OSDN Git Service
Eric Dumazet [Thu, 19 Apr 2012 02:24:36 +0000 (02:24 +0000)]
ipv6: tcp: dont drop packet but consume it
When we need to clone skb, we dont drop a packet.
Call consume_skb() to not confuse dropwatch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 19 Apr 2012 02:24:28 +0000 (02:24 +0000)]
netlink: dont drop packet but consume it
When we need to clone skb, we dont drop a packet.
Call consume_skb() to not confuse dropwatch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 19 Apr 2012 02:24:17 +0000 (02:24 +0000)]
ip6_tunnel: dont drop packet but consume it
When we need to reallocate skb, we dont drop a packet.
Call consume_skb() to not confuse dropwatch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shan Wei [Wed, 18 Apr 2012 18:05:46 +0000 (18:05 +0000)]
net: fix compile error of leaking kmemleak.h header
net/core/sysctl_net_core.c: In function ‘sysctl_core_init’:
net/core/sysctl_net_core.c:259: error: implicit declaration of function ‘kmemleak_not_leak’
with same error in net/ipv4/route.c
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huang, Xiong [Tue, 17 Apr 2012 19:32:36 +0000 (19:32 +0000)]
atl1c: restore max-read-request-size in Device Conrol Register
in some platforms, we found the max-read-request-size in Device Control
Register is set to 0 by (BIOS?) during bootup, this will cause the
performance(throughput) very bad.
Restore it to a min-value.
register definition of REG_DEVICE_CTRL is removed, using kernel API to
access it as it's a standard pcie register.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huang, Xiong [Tue, 17 Apr 2012 19:32:35 +0000 (19:32 +0000)]
atl1c: using fixed TXQ configuration for l2cb and l1c
using fixed TXQ config for l2cb and l1c regardless dmar_block
to make tx-DMA more stable.
register REG_TXQ_CTRL is refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huang, Xiong [Tue, 17 Apr 2012 19:32:34 +0000 (19:32 +0000)]
atl1c: remove dmaw_block
dmaw_block is never used in the driver, remove it.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huang, Xiong [Tue, 17 Apr 2012 19:32:33 +0000 (19:32 +0000)]
atl1c: correct wrong definition of REG_DMA_CTRL
some fields of REG_DMA_CTRL(15C0) are wrong, replace with the newest one.
haredware uses fixed dma-write-block size, remove dmaw_block related code
in function atl1c_configure_dma.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huang, Xiong [Tue, 17 Apr 2012 19:32:32 +0000 (19:32 +0000)]
atl1c: wrong register used to stop TXQ
function atl1c_stop_mac uses wrong register of REG_TWSI_CTRL
to stop mac, replace it with REG_TXQ_CTRL.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huang, Xiong [Tue, 17 Apr 2012 19:32:31 +0000 (19:32 +0000)]
atl1c: remove code related to rxq 1/2/3
remove code related to rxq 1/2/3 since multi-q not support.
refine REG_RXQ_CTRL definition as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huang, Xiong [Tue, 17 Apr 2012 19:32:30 +0000 (19:32 +0000)]
atl1c: split 2 32bit registers of TPD to 4 16bit registers
TPD producer/consumer index is 16bit wide.
16bit read/write reduce the dependency of the 2 tpd rings (hi and lo)
rename reg(157C/1580) to keep name coninsistency.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huang, Xiong [Tue, 17 Apr 2012 19:32:29 +0000 (19:32 +0000)]
atl1c: remove SMB/CMB DMA related code
l1c & later chips don't support DMA for SMB.
CMB is removed from hardware.
reg(15C8) is used to trig interrupt by tpd threshold.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huang, Xiong [Tue, 17 Apr 2012 19:32:28 +0000 (19:32 +0000)]
atl1c: remove VPD register
VPD register is only used for L1(devid=PCI_DEVICE_ID_ATTANSIC_L1) to
access external NV-memory.
l1c & later chip doesn't use it any more.
PHY 0/1 registers occupy the last 2 slots of the dump table.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huang, Xiong [Tue, 17 Apr 2012 19:32:27 +0000 (19:32 +0000)]
atl1c: remove HDS register
remove HDS register as it doesn't exist in hardware.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huang, Xiong [Tue, 17 Apr 2012 19:32:26 +0000 (19:32 +0000)]
atl1c: remove multiple-RX-Q code
the multiple-RX-Q in hardware doesn't work,
all related register definition & code are removed.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huang, Xiong [Tue, 17 Apr 2012 19:32:25 +0000 (19:32 +0000)]
atl1c: update author contact info & company/driver desciption
replace unavailable email of the author since he left with a mail-list.
update company info as well, Atheros was acquired by Qualcomm.
insert "100" to driver description since it support 100M controller.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville [Wed, 18 Apr 2012 18:17:13 +0000 (14:17 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
drivers/net/wireless/iwlwifi/iwl-testmode.c
include/net/nfc/nfc.h
net/nfc/netlink.c
net/wireless/nl80211.c
David S. Miller [Wed, 18 Apr 2012 17:21:59 +0000 (13:21 -0400)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
* remove duplicated line in comment
* add htons() invocation for tt_crc as suggested by Al Viro
* OriGinator Message seqno initial value is now random
* some cleanups and fixes
Antonio Quartulli [Sun, 26 Feb 2012 14:39:42 +0000 (15:39 +0100)]
batman-adv: skip the window protection test when the originator has no neighbours
When we receive an OGM from from a node for the first time, the last_real_seqno
field of the orig_node structure has not been initialised yet. The value of this
field is used to compute the current ogm-seqno window and therefore the
protection mechanism will probably drop the packet due to an out-of-window error.
To avoid this situation this patch adds a check to skip the window protection
mechanism if no neighbour nodes have already been added. When the first
neighbour node is added, the last_real_seqno field is initialised too.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Antonio Quartulli [Sun, 26 Feb 2012 14:39:41 +0000 (15:39 +0100)]
batman-adv: print OGM seq numbers as unsigned int
OGM sequence numbers are declared as uint32_t and so they have to printed
using %u instead of %d in order to avoid wrong representations.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Antonio Quartulli [Sat, 18 Feb 2012 10:27:34 +0000 (11:27 +0100)]
batman-adv: use ETH_HLEN instead of sizeof(struct ethhdr)
Instead of using sizeof(struct ethhdr) it is strongly recommended to use the
kernel macro ETH_HLEN. This patch substitute each occurrence of the former
expressione with the latter one.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Tue, 7 Feb 2012 09:20:51 +0000 (17:20 +0800)]
batman-adv: mark existing ogm variables as batman iv
The coming protocol changes also will have a part called "OGM". That
makes it necessary to introduce a distinction in the code base.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Tue, 7 Feb 2012 09:20:50 +0000 (17:20 +0800)]
batman-adv: rename BATMAN_OGM_LEN to BATMAN_OGM_HLEN
Using BATMAN_OGM_LEN leaves one with the impression that this is
the full packet size which is not the case. Therefore the variable
is renamed.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Tue, 7 Feb 2012 09:20:49 +0000 (17:20 +0800)]
batman-adv: refactoring API: find generalized name for bat_ogm_init_primary callback
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Tue, 7 Feb 2012 09:20:48 +0000 (17:20 +0800)]
batman-adv: handle routing code initialization properly
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Tue, 7 Feb 2012 09:20:47 +0000 (17:20 +0800)]
batman-adv: add iface_disable() callback to routing API
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Tue, 7 Feb 2012 09:20:46 +0000 (17:20 +0800)]
batman-adv: randomize initial seqno to avoid collision
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Tue, 7 Feb 2012 09:20:45 +0000 (17:20 +0800)]
batman-adv: refactoring API: find generalized name for bat_ogm_init callback
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Tue, 7 Feb 2012 09:19:58 +0000 (17:19 +0800)]
batman-adv: move ogm initialization into the proper function
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Antonio Quartulli [Wed, 18 Apr 2012 07:47:57 +0000 (09:47 +0200)]
batman-adv: remove duplicated line in comment
Remove an accidentally added duplicated line in a function comment
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Antonio Quartulli [Sat, 14 Apr 2012 11:15:27 +0000 (13:15 +0200)]
batman-adv: convert the tt_crc to network order
Before sending out a TT_Request packet we must convert the tt_crc field value
to network order (since it is 16bits long).
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
majianpeng [Mon, 16 Apr 2012 19:58:28 +0000 (19:58 +0000)]
net/core:Remove memleak reports by kmemleak_not_leak.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
majianpeng [Mon, 16 Apr 2012 19:33:31 +0000 (19:33 +0000)]
net/ipv4:Remove two memleak reports by kmemleak_not_leak.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 17 Apr 2012 16:51:19 +0000 (16:51 +0000)]
net: filter: remove unused cpu_off in sparc JIT
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
françois romieu [Tue, 17 Apr 2012 11:11:40 +0000 (11:11 +0000)]
dmfe: enforce consistent timing delay.
The driver does not always use the same timing for what looks like
the same operations.
- DCR0
Use the same udelay everywhere for reset. Upper bound is 100 us.
- DCR9
Use 5us delay for srom clock. 1us delay for phy_write_1bit (writes
PHY_DATA_[01]) are not changed as they stay withing a 2,5MHz MDIO
clock range.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Apr 2012 20:38:16 +0000 (16:38 -0400)]
net: filter: Fix some more small issues in sparc JIT.
Fix mixed space and tabs.
Put bpf_jit_load_*[] externs into bpf_jit.h
"while(0)" --> "while (0)"
"COND (X)" --> "COND(X)"
Document branch offset calculations, and bpf_error's return
sequence.
Document the reason we need to emit three nops between the
%y register write and the divide instruction.
Remove erroneous trailing semicolons from emit_read_y() and
emit_write_y().
Based upon feedback from Sam Ravnborg.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Apr 2012 20:08:29 +0000 (16:08 -0400)]
net: filter: Fix some minor issues in sparc JIT.
Correct conventions comments. %o4 and %o5 were swapped,
%g3 was not documented.
Use r_TMP instead of r_SKB_DATA + r_OFF where possible in
assembler stubs.
Correct discussion of %o4 and %o5 in one of bpf_jit_compile()'s
comments.
Based upon feedback from Richard Mortimer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Amitkumar Karwar [Tue, 17 Apr 2012 04:36:52 +0000 (21:36 -0700)]
mwifiex: corrections in timestamp related code
We get two timing related fields for each bss from firmware in scan
results.
1) timestamp - Actual timestamp information in probe response/beacon
2) network_tsf - firmware's TSF value at the time the beacon or probe
response was received.
Both are needed while associating by firmware.
The patch takes care of following things.
1) We should pass "timestamp" to cfg80211_inform_bss(), but currently
"network_tsf" is being provided. This error is corrected here.
2) Rename "network_tsf" to "fw_tsf"
3) Make use of u64 variable instead of an array of u8/u32 to save
parsed "timestamp" information.
4) Use timestamp provided to stack in scan results using
cfg80211_inform_bss() while associating. (bss->tsf)
5) Allocate space to save fw_tsf in "priv" of cfg80211_bss
and retrieve it while associating.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Tue, 17 Apr 2012 04:36:51 +0000 (21:36 -0700)]
mwifiex: code cleanup in BSS handling
Rearrange some code to save extra parameters to the functions.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Mon, 16 Apr 2012 22:53:55 +0000 (23:53 +0100)]
libertas USB: convert to asynchronous firmware loading
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Mon, 16 Apr 2012 22:53:43 +0000 (23:53 +0100)]
libertas SDIO: convert to asynchronous firmware loading
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Mon, 16 Apr 2012 22:53:26 +0000 (23:53 +0100)]
libertas: add asynchronous firmware loading capability
As described at
http://article.gmane.org/gmane.linux.kernel.wireless.general/86084
libertas is taking a long time to load because it loads firmware
during module loading.
Add a new API for interface drivers to load their firmware
asynchronously. The same semantics of the firmware table are followed
like before.
Interface drivers will be converted in follow-up patches, then we can
remove the old, synchronous firmware loading function.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Mon, 16 Apr 2012 22:53:02 +0000 (23:53 +0100)]
libertas: harden-up exit paths
These simple sanity check avoids extra complexity in error paths when
moving to asynchronous firmware loading (which means the device may fail to
init some time after its creation).
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Mon, 16 Apr 2012 22:52:42 +0000 (23:52 +0100)]
libertas: Firmware loading simplifications
Remove the ability to pass module parameters with firmware filenames
for USB and SDIO interfaces.
Remove the ability to pass custom "user" filenames to lbs_get_firmware().
Remove the ability to reprogram internal device memory with a different
firmware from the USB driver (we don't know of any users), and simplify
the OLPC firmware loading quirk to simply placing the OLPC firmware
at the top of the list (we don't know of any users other than OLPC).
Move lbs_get_firmware() into its own file.
These simplifications should have no real-life effect but make the
upcoming transition to asynchronous firmware loading considerably less
painful.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andreas Hartmann [Mon, 16 Apr 2012 22:25:28 +0000 (00:25 +0200)]
rt2x00: Don't let mac80211 send a BAR when an AMPDU subframe fails
There are connection stalls or very poor throughputs with rt2800
hardware using 802.11n in AP mode since patch "mac80211: retry sending
failed BAR frames later instead of tearing down aggr"[1][2].
Since rt2800 hardware is not able to correctly report the tx status of
BAR frames, this patch removes as workaround the existing error handling
on AP side, which lets mac80211 send a BAR when an AMPDU subframe fails.
As a result, most wifi clients (aside from Intel STAs on Windows)
instead will timeout now the reorder buffer and request the lost frame
again.
The correct solution would be, to tear down BA session on AP side.
This patch was born on the basis of "[RFT] rt2x00: Tear down BA
session on QoS frame failure"[3].
Thanks to Helmut Schaa for his support!
[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/83297/focus=83304
[2] http://git.kernel.org/?p=linux/kernel/git/linville/wireless-testing.git;a=commit;h=
f0425beda4d404a6e751439b562100b902ba9c98
[3] http://thread.gmane.org/gmane.linux.drivers.rt2x00.user/569
Signed-off-by: Andreas Hartmann <andihartmann@01019freenet.de>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 16 Apr 2012 20:46:32 +0000 (22:46 +0200)]
ath9k: use ath9k_hw_fbin2freq instead of FBIN2FREQ
The FBIN2FREQ macro and the ath9k_hw_fbin2freq function
does the same thing. Remove the macro, and use the inline
function instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 16 Apr 2012 20:46:31 +0000 (22:46 +0200)]
ath9k: move ath9k_hw_fbin2freq function to eeprom.h
Both eeprom.c and ar9003_eeprom.c has an indentical
'ath9k_hw_fbin2freq' function. Move the function to
a common place and remove the duplicates.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 16 Apr 2012 20:22:50 +0000 (22:22 +0200)]
ath9k: remove unused PWRINC_*_TO_*_CHAIN defines
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 16 Apr 2012 20:22:49 +0000 (22:22 +0200)]
ath9k: merge power correction constants
The existing constants are used for reduction/increase
tx power level on devices with 2x2 and 3x3 chainmask.
Both reduction and increase must use the same value, so
it makes no sense to use separate constants for them.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Mon, 16 Apr 2012 15:44:00 +0000 (17:44 +0200)]
drivers/net/wireless/libertas/if_usb.c: add missing debugging code
Add a corresponding leave call on error failure.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hayes Wang [Fri, 30 Mar 2012 06:48:06 +0000 (14:48 +0800)]
r8169: support the new RTL8411 chip.
Compared with previous chipsets, it needs no special action trough the
jumbo{enable/disable} helpers to operate with jumbo frames.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Hayes Wang [Fri, 30 Mar 2012 06:33:03 +0000 (14:33 +0800)]
r8169: adjust some functions of 8111f
Put some settings of 8111f into one function which may be reused.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Hayes Wang [Fri, 30 Mar 2012 06:33:02 +0000 (14:33 +0800)]
r8169: support the new RTL8402 chip.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Hayes Wang [Fri, 30 Mar 2012 06:33:01 +0000 (14:33 +0800)]
r8169: add device specific CSI access helpers.
New chipsets need it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Hayes Wang [Fri, 30 Mar 2012 06:33:00 +0000 (14:33 +0800)]
r8169: modify pll power function
Adjust r810x_pll_power_down, r810x_pll_power_up, and r8168_pll_power_up.
Always power up device during rtl_open. For r810x, turn off more power
when the WOL is disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Francois Romieu [Tue, 17 Apr 2012 09:12:01 +0000 (11:12 +0200)]
r8169: 8168c and later require bit 0x20 to be set in Config2 for PME signaling.
The new 84xx stopped flying below the radars.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Francois Romieu [Tue, 17 Apr 2012 09:10:11 +0000 (11:10 +0200)]
r8169: Config1 is read-only on 8168c and later.
Suggested by Hayes.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Randy Dunlap [Mon, 16 Apr 2012 15:01:33 +0000 (15:01 +0000)]
hippi: fix printk format in rrunner.c
Fix printk format warning (from i386 build):
drivers/net/hippi/rrunner.c:146:9: warning: format '%08llx' expects type 'long long unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Jes Sorensen <jes@trained-monkey.org>
Cc: linux-hippi@sunsite.dk
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Apr 2012 03:47:37 +0000 (23:47 -0400)]
Merge branch 'master' of git://gitorious.org/linux-can/linux-can-next
David S. Miller [Mon, 16 Apr 2012 03:06:27 +0000 (20:06 -0700)]
net: filter: Just In Time compiler for sparc
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Mon, 26 Mar 2012 15:23:39 +0000 (08:23 -0700)]
iwlwifi: remove get_cmd_string
The command strings are needed through the layers for
debug and error messages, but can differ with opmode.
As a result, we need to give the command names to the
transport layer as configuration.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Mon, 16 Apr 2012 21:48:08 +0000 (14:48 -0700)]
iwlwifi: optimize struct iwl_cmd_meta layout
Having a u32 before a potential 64-bit value is
not very efficient, move it last.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
David Spinadel [Mon, 16 Apr 2012 21:43:30 +0000 (14:43 -0700)]
iwlwifi: expose static methods for MVM use
To support hybrid state of MVM op_mode, most of the functioanallity
will be done using DVM functions.
When MVM will have independant live, the declarations will be removed
and the functions will be static back.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
David Spinadel [Thu, 15 Mar 2012 09:22:31 +0000 (11:22 +0200)]
iwlwifi: phy db channel to tx power channel group
Implement mapping of channel to TX power channel group,
for sending channel specific data before add context.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Dor Shaish [Mon, 26 Mar 2012 15:20:55 +0000 (08:20 -0700)]
iwlwifi: Disabling calibrations variable
Add a variable for disabling specific calibrations.
Merged old variables for calibrations disabling.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Emmanuel Grumbach [Tue, 20 Mar 2012 12:50:09 +0000 (14:50 +0200)]
iwlwifi: remove uneeded include from iwl-pci.c
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
David Spinadel [Tue, 13 Mar 2012 12:46:38 +0000 (14:46 +0200)]
iwlwifi: remove double verification of ucode sections
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
David Spinadel [Tue, 13 Mar 2012 12:32:48 +0000 (14:32 +0200)]
iwlwifi: set size of ucode section
Set size of firmware section in mvm bundle format.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 23 Mar 2012 15:37:30 +0000 (08:37 -0700)]
iwlwifi: remove iwl_tx_queue declaration
The declaration isn't needed as the struct is only
used in code that includes the right header file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Don Fry [Fri, 23 Mar 2012 15:34:31 +0000 (08:34 -0700)]
iwlwifi: move status definitions from iwl-shared
The code has been changed, move the definitions to the proper file
being used by the code.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Amit Beka [Sun, 19 Feb 2012 09:07:46 +0000 (11:07 +0200)]
iwlwifi: added HBUS_TARG_TEST_REG
This register is used to enable some debug mechanisms.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Don Fry [Tue, 20 Mar 2012 23:36:54 +0000 (16:36 -0700)]
iwlwifi: move HCMD_ACTIVE to trans
The HCMD_ACTIVE bit is only used in trans.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Don Fry [Tue, 20 Mar 2012 17:33:34 +0000 (10:33 -0700)]
iwlwifi: complete STATUS_READY refactoring
When WiMax takes over the RF, inform the op_mode.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 9 Mar 2012 08:42:52 +0000 (09:42 +0100)]
iwlwifi: remove antenna from mod params struct
It doesn't even exist as a module parameter,
so just remove the item from the struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 9 Mar 2012 08:16:35 +0000 (09:16 +0100)]
iwlwifi: remove uCode alternatives mechanism
We've never released firmware using the alternatives
mechanism and our build process makes that difficult
anyway. This means that in every file we have ever
built (except maybe by hand for testing) the listed
alternative was 0. Make the alternative field in the
TLVs part of the TLV number (thus expanding that to
32 bits); this gives us more TLV numbers (not really
needed) and more importantly protects against rogue
firmware files that actually do use the alternatives
mechanism -- those will now be rejected since they
don't contain any valid TLVs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 9 Mar 2012 07:58:46 +0000 (08:58 +0100)]
iwlwifi: remove no_sleep_autoadjust
My original idea with this was to adjust the sleep
pattern of the uCode based on the maximum network
latency userspace asked for. Due to nobody wanting
to test it, this logic was disabled by default. It
seems the time has come to remove it, since it's
not only always disabled but there also don't seem
to be any applications that actually request a max
network latency.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Axel Lin [Sat, 14 Apr 2012 04:38:43 +0000 (12:38 +0800)]
net/can: use module_pci_driver
This patch converts the drivers in drivers/net/can/* to use
module_pci_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-can@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Daniel Baluta [Sun, 25 Mar 2012 23:05:50 +0000 (02:05 +0300)]
can: fix sparse warning for cgw_list
Make cgw_list static to remove the following sparse warning:
net/can/gw.c:69:1: warning: symbol 'cgw_list' was not declared.
Should it be static?
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Xose Vazquez Perez [Sat, 14 Apr 2012 21:33:21 +0000 (23:33 +0200)]
wireless: rt2x00: rt2800pci add more RT539x ids
RT539x devices:
(0x1814, 0x5362)
(0x1814, 0x5392)
Taken from ralink driver 2011_0406_RT5390_RT5392_Linux_STA_V2.5.0.3_DPO
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Xose Vazquez Perez [Sat, 14 Apr 2012 21:00:01 +0000 (23:00 +0200)]
wireless: rt2x00: rt{2500,73}usb.c put back duplicate id
put back 0x050d,0x7050 to rt73usb, same usb_id for two chips:
K7SF5D7050A ver 2xxx is rt2500
K7SF5D7050B ver 3xxx is rt73
<http://en-us-support.belkin.com/app/answers/detail/a_id/297/kw/K7SF5D7050>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Sat, 14 Apr 2012 20:01:59 +0000 (22:01 +0200)]
ath9k: simplify ath9k_hw_get_scaled_power function
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Sat, 14 Apr 2012 20:01:58 +0000 (22:01 +0200)]
ath9k: introduce ath9k_hw_get_scaled_power helper
The computation of the scaled power value in
various eeprom files uses identical code. Move
that code into a helper function and use that
instead of code duplication.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Sat, 14 Apr 2012 20:01:57 +0000 (22:01 +0200)]
ath9k: use consistent value for REDUCE_SCALED_POWER_BY_THREE_CHAIN
The REDUCE_SCALED_POWER_BY_THREE_CHAIN symbol is
defined in different eeprom files, and the value
varies between the different files.
In eeprom_def.c and in ar9003_eeprom.c the value
of the symbol is 9, however the comments in these
files indicates the value should be 10*log10(3)*2
which is 9.
54242509439325. Replace the the value
to 10 in these files.
Also add comments to eeprom_9287.c.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Sat, 14 Apr 2012 18:35:19 +0000 (20:35 +0200)]
ath9k: use ath9k_hw_update_regulatory_maxpower in ath9k_hw_def_set_txpower
We have a helper function for updating the max_power_level
value. Use that and remove the duplicated code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Axel Lin [Sat, 14 Apr 2012 02:38:36 +0000 (10:38 +0800)]
net/wireless: use module_pci_driver
This patch converts the drivers in drivers/net/wireless/* to use
module_pci_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Simon Kelley <simon@thekelleys.org.uk>
Cc: Jouni Malinen <j@w1.fi>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 13 Apr 2012 19:02:57 +0000 (12:02 -0700)]
mac80211: add function retrieve average rssi
Add utility function to provide the average rssi per vif
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 13 Apr 2012 18:57:43 +0000 (13:57 -0500)]
rtlwifi: rtl8192ce: Remove false positives for kmemleak
When rtl8192ce is in operation, kmemleak indicates a number of leaks, yet
when the driver is removed all are gone. These false positives happen
in two locations:
unreferenced object 0xffff880041124000 (size 9536):
comm "work_for_cpu", pid 9295, jiffies
4295037203 (age 20596.320s)
hex dump (first 32 bytes):
33 00 00 01 01 6d 00 00 00 00 b1 0e 21 0b 00 00 3....m......!...
01 01 6d 00 00 00 00 8b 20 c0 e9 00 00 01 01 6d ..m..... ......m
backtrace:
[<
ffffffff8137a1b1>] kmemleak_alloc+0x21/0x50
[<
ffffffff8138d01f>] kmalloc_large_node+0x9a/0xa6
[<
ffffffff811335a5>] __kmalloc_node_track_caller+0x175/0x3b0
[<
ffffffff812ddfe3>] __alloc_skb+0x73/0x230
[<
ffffffff812de1b8>] dev_alloc_skb+0x18/0x30
[<
ffffffffa091a3b7>] rtl_pci_probe+0x10e0/0x17d2 [rtlwifi]
-- snip --
unreferenced object 0xffff8800b4d3f600 (size 256):
comm "kworker/u:2", pid 13221, jiffies
4297830173 (age 9424.568s)
hex dump (first 32 bytes):
1c d6 45 b1 00 88 ff ff 1c d6 45 b1 00 88 ff ff ..E.......E.....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<
ffffffff8137a1b1>] kmemleak_alloc+0x21/0x50
[<
ffffffff81130f43>] kmem_cache_alloc_node+0x153/0x270
[<
ffffffff812ddfb6>] __alloc_skb+0x46/0x230
[<
ffffffff812de1b8>] dev_alloc_skb+0x18/0x30
[<
ffffffffa093264a>] rtl92c_set_fw_rsvdpagepkt+0x22a/0x5c0 [rtl8192c_common]
-- snip --
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yoshinori Sato [Fri, 13 Apr 2012 15:32:32 +0000 (00:32 +0900)]
ath5k: add PCI id
This device works fine of ath5k.
Details bellow
05:00.0 0200: 168c:ff1b (rev 01)
05:00.0 Ethernet controller: Atheros Communications Inc. Device ff1b (rev 01)
Flags: bus master, fast devsel, latency 0, IRQ 19
Memory at
febf0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath5k
ath5k 0000:05:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ath5k 0000:05:00.0: setting latency timer to 64
ath5k 0000:05:00.0: registered as 'phy0'
ath: EEPROM regdomain: 0x67
ath: EEPROM indicates we should expect a direct regpair map
ath: Country alpha2 being used: 00
ath: Regpair used: 0x67
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 13 Apr 2012 11:14:22 +0000 (16:44 +0530)]
ath9k: fix beacon descriptor
The tx interrupt for beacon queue is configured only for edma chips.
As the edma chip does not support per descriptor interrupt, no need to
set INTREQ for every beacon descriptor. And also clear ps filter for
beacon frame.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 13 Apr 2012 11:14:21 +0000 (16:44 +0530)]
ath9k: skip beaconing when reset work is pending
Whenever the reset work is queued up, do not generate beacon. And also
clear the beacon miss count once the beacon stuck was observed.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 13 Apr 2012 11:14:20 +0000 (16:44 +0530)]
ath9k: reset noiseimmunity level to default
After the chip reset, the noise immunity levels are restored with
history values. If the immunity levels are lower than the defaults,
lets start with the optimal values.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 13 Apr 2012 11:08:40 +0000 (16:38 +0530)]
cfg80211: increse bss expire time
The background scan completion takes more time when the station is
having heavy uplink traffic. The scan state machine decides to fall
back to home channel on every off-channel visit when there are pending
frames in tx queue. bgscan completion took ~30sec on dual band US
regulatory card.
scan period = (20 active channels * probe timeout) +
(12 passive channels * passive probe timeout) +
(32 * timeout on home channel) +
(32 * flush timeout)
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 13 Apr 2012 07:46:34 +0000 (13:16 +0530)]
ath9k: fix ibss beacon next tbtt
Sync-up ibss beacon timer with the beacon frame's timestamp. When the
node acts as joiner, it has to sync with the received beacon timestamp
instead of reading tsf from hw. As the hw tsf wont wont be update till
bssid is configured. This patch programs hw tsf with the received beacon
timestamp if beacon timers are yet to be configured.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 13 Apr 2012 07:46:33 +0000 (13:16 +0530)]
ath9k: fix ibss fair beacon distribution for AR9462
Update AR9462 initval to fix unbalance beacon distribution
in Ad-Hoc network.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Neal Cardwell [Mon, 16 Apr 2012 07:08:06 +0000 (07:08 +0000)]
tcp: restore formatting of macros for tcp_skb_cb sacked field
Commit
b82d1bb4 inadvertendly placed unrelated new code between
TCPCB_EVER_RETRANS and TCPCB_RETRANS and the other macros that refer
to the sacked field in the struct tcp_skb_cb (probably because there
was a misleading empty line there). This commit fixes up the
formatting so that all macros related to the sacked field are adjacent
again.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Zelenoff [Sun, 15 Apr 2012 21:27:29 +0000 (21:27 +0000)]
atl1: remove unused member from atl1_adapter structure
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Renzelmann [Thu, 12 Apr 2012 22:42:43 +0000 (17:42 -0500)]
hostap: GFP_ATOMIC/GFP_KERNEL cleanup
The driver is allocating memory during initialization with GFP_ATOMIC
even though GFP_KERNEL is sufficient. This patch fixes it.
Signed-off-by: Matt Renzelmann <mjr@cs.wisc.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Thu, 12 Apr 2012 21:32:23 +0000 (14:32 -0700)]
mac80211: Take into account TSF adjustment latency in Toffset setpoint
When testing mesh synchronization we observed a global TSF slowdown that
was dependent on the number of synchronized mesh stations. This seems
to be caused by the TSF adjustment (read/write) latency.
Adding a small margin to the Toffset setpoint solved the problem.
Signed-off-by: Shinichi Hotori <hotorinn@gmail.com>
Signed-off-by: Yu Niiro <yu.niiro@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Thu, 12 Apr 2012 21:32:22 +0000 (14:32 -0700)]
mac80211: Choose a new toffset setpoint if a big tsf jump is detected.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Thu, 12 Apr 2012 21:32:21 +0000 (14:32 -0700)]
mac80211_hwsim: fixup for tsf setting
Last patch I sent failed to take into account the offset of each phy.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>