OSDN Git Service
Arnd Bergmann [Fri, 22 May 2015 15:33:12 +0000 (17:33 +0200)]
Merge branch 'for-upstream/juno-dts' of git://linux-arm.org/linux-ld into next/dt
Merge "Documentation: bindings: Add DT bindings for ARM Juno boards" from Liviu Dudau:
* 'for-upstream/juno-dts' of git://linux-arm.org/linux-ld:
Documentation: bindings: Add DT bindings for ARM Juno boards.
arm64: Add DT support for Juno r1 board.
arm64: Juno: Add GICv2m support in device tree.
arm64: Juno: Add memory mapped timer node
arm64: Juno: Split juno.dts into juno-base.dtsi and juno.dts.
arm64: Juno: Fix the GIC node address label and the frequency of FAXI clock.
Arnd Bergmann [Fri, 29 May 2015 12:01:52 +0000 (14:01 +0200)]
Merge tag 'qcom-arm64-for-4.2' of git://git./linux/kernel/git/galak/linux-qcom into next/dt
Merge "Qualcomm ARM64 Updates for v4.2" Kumar Gala:
* Added SPMI PMIC Arbiter device tree node for MSM8916
* Added 8x16 chipset SPMI PMIC's nodes
* Added MSM8916 restart device node
* Added initial set of PMIC and SoC pins for APQ8016 SBC board
* tag 'qcom-arm64-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
arm64: dts: qcom: Add initial set of PMIC and SoC pins for APQ8016 SBC board
arm64: dts: qcom: Add MSM8916 restart device node
arm64: dts: qcom: Add 8x16 chipset SPMI PMIC's nodes
arm64: dts: qcom: Add SPMI PMIC Arbiter node for MSM8916
Arnd Bergmann [Fri, 29 May 2015 11:59:55 +0000 (13:59 +0200)]
Merge tag 'renesas-dt2-for-v4.2' of git://git./linux/kernel/git/horms/renesas into next/dt
Merge "Second Round of Renesas ARM Based SoC DT Updates for v4.2" from Simon Horman:
* Describe DMA for the serial ports of R-Car Gen2 SoCs
* Add MMCIF max-frequency to R-Car Gen2 SoCs
* Use "nor-jedec" instead of "jedec,spi-nor"
* tag 'renesas-dt2-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790 dtsi: Describe DMA for the serial ports
ARM: shmobile: r8a7791 dtsi: Describe DMA for the serial ports
ARM: shmobile: r8a7794 dtsi: Describe DMA for the serial ports
ARM: shmobile: r8a7791: add MMCIF max-frequency
ARM: shmobile: r8a7790: add MMCIF max-frequency
ARM: shmobile: bockw dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: henninger dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: bockw-reference dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: koelsch dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: lager dts: Replace "nor-jedec" by "jedec,spi-nor"
Arnd Bergmann [Fri, 29 May 2015 11:58:41 +0000 (13:58 +0200)]
Merge tag 'zynq-dt-for-4.2' of https://github.com/Xilinx/linux-xlnx into next/dt
Merge "arm: Xilinx Zynq dt patches for v4.2" from Michal Simek:
- Fix aliases and stdout properties
- Document current TTC binding
- Add Ceva to prefixes
- Use new compatible string for MACB
* tag 'zynq-dt-for-4.2' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: DT: Use the zynq binding with macb
of: Add vendor prefix for Ceva
PCI: xilinx: Trivial fix in DT example
devicetree: cadence_ttc: Document binding for timer width
ARM: dts: zynq: Fix stdout-path and bootargs
ARM: dts: zynq: Add missing alias node for zybo and parallella
Arnd Bergmann [Fri, 29 May 2015 11:56:58 +0000 (13:56 +0200)]
Merge tag 'v4.1-next-dts' of https://github.com/mbgg/linux-mediatek into next/dt
Merge "ARM: mediatek: dts updates for v4.2" from Matthias Brugger:
- dts: add pinctrl/GPIO/EINT to mt8135
- dts: fix uart address for mt8127
* tag 'v4.1-next-dts' of https://github.com/mbgg/linux-mediatek:
ARM: dts: mt8127: correct uart instance address
ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135.
Arnd Bergmann [Fri, 29 May 2015 11:55:50 +0000 (13:55 +0200)]
Merge tag 'qcom-dt-for-4.2' of git://git./linux/kernel/git/galak/linux-qcom into next/dt
Merge "Qualcomm ARM Based Device Tree Updates for v4.2" from Kumar Gala:
* Added support for regulators, USB Host & OTG, SATA, and i2c
controllers on APQ8064 based platforms
* Added PM8841/PM8941/PMA8084 device nodes
* Added PMU support on MSM8660
* tag 'qcom-dt-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: dts: qcom: Add msm8660 PMU node
ARM: dts: qcom: Add PMA8084 functions device nodes
ARM: dts: qcom: Add PM8941 functions device nodes
ARM: dts: qcom: Add PM8841 functions device nodes
ARM: dts: qcom: apq8064 - add i2c3 node for panel.
ARM: dts: qcom: apq8064 - Move i2c1 pinctrl to apq8064.dtsi
ARM: dts: qcom: apq8064-ifc6410 - Add DT alias for serial port
ARM: dts: qcom: apq8064 - Add USB OTG support for CM QS-600
ARM: dts: qcom: apq8064 - Add usb host support to CM QS-600
ARM: dts: qcom: apq8064-cm-qs600 - Add basic regulators
ARM: dts: qcom: apq8064 - Add SATA controller support
ARM: dts: qcom: apq8064 - Add USB OTG support
ARM: dts: qcom: apq8064 - Add usb host support.
ARM: dts: qcom: apq8064-ifc6410 - Add basic regulators
ARM: dts: qcom: apq8064 - add RPM regulators support
Arnd Bergmann [Thu, 28 May 2015 20:41:13 +0000 (22:41 +0200)]
Merge tag 'omap-for-v4.2/dt-pt1' of git://git./linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Device tree related changes for omaps" from Tony Lindgren:
- Configure MMC data lines 4..8 for 1.8V IO on boards that
are using them as GPIOs instead of MMC data lines
- Add support for Baltos IR5221
- Add device tree support for LogicPD Torpedo devkit
- Add 3717 core pinctrl region
- Add gta04 1w and GSM audio support
- Add wilink and ov2659 support for am437x-gp-evm
- Add am335x-evm bluetooth and mmc3 support
- Enable omap5-uevm uart wakeup interrupt
- Enable I2C2 on BeagleBone as it's used for the capes
- Use defines for LDP GPIO keys
* tag 'omap-for-v4.2/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-evm: add mmc3 and wlan definitions to dts
ARM: dts: Enable SDIO card interrupt for 37xx-evm
ARM: dts: Fix ldp gpio keys to use defines
ARM: dts: Beaglebone i2c definitions
ARM: dts: am437x-gp-evm: add DT nodes for ov2659 sensor
ARM: dts: add DTS for Baltos IR5221
ARM: dts: omap5-uevm: Add Uart wakeup interrupt
ARM: dts: omap3-gta04: Add GSM audio support
ARM: dts: am335x-evm: add bluetooth support
ARM: dts: am437x-gp-evm: add wilink8 support
ARM: dts: omap3-gta04: Add hdqw1 support
ARM: dts: add core2 padconf region for am3517
ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit
ARM: OMAP3: Add support for configuring MMC pins as GPIO pins
Nathan Sullivan [Wed, 27 May 2015 20:00:01 +0000 (15:00 -0500)]
ARM: zynq: DT: Use the zynq binding with macb
Use the new zynq binding for macb ethernet, since it will disable half
duplex gigabit like the Zynq TRM says to do. Also allow the compatible
cadence gem binding that won't disable half duplex but works otherwise.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 9 Apr 2015 06:22:41 +0000 (08:22 +0200)]
of: Add vendor prefix for Ceva
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 2 Oct 2014 10:36:45 +0000 (12:36 +0200)]
PCI: xilinx: Trivial fix in DT example
Good to have it properly describe for c&p cases.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Peter Crosthwaite [Tue, 22 Jul 2014 00:25:26 +0000 (17:25 -0700)]
devicetree: cadence_ttc: Document binding for timer width
Modern TTC implementations can extend the timer width to 32 bit. This
feature is not self identifying so the driver needs to be made aware
via device tree.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 11 Feb 2015 12:06:36 +0000 (13:06 +0100)]
ARM: dts: zynq: Fix stdout-path and bootargs
parallella - Remove linux,stdout-path.
Use stdout-path to identify kernel console
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Michal Simek [Wed, 11 Feb 2015 12:05:11 +0000 (13:05 +0100)]
ARM: dts: zynq: Add missing alias node for zybo and parallella
Add missing alias node.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Geert Uytterhoeven [Wed, 20 May 2015 17:46:25 +0000 (19:46 +0200)]
ARM: shmobile: r8a7790 dtsi: Describe DMA for the serial ports
Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven [Wed, 20 May 2015 17:46:26 +0000 (19:46 +0200)]
ARM: shmobile: r8a7791 dtsi: Describe DMA for the serial ports
Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven [Wed, 20 May 2015 17:46:27 +0000 (19:46 +0200)]
ARM: shmobile: r8a7794 dtsi: Describe DMA for the serial ports
Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Thu, 14 May 2015 07:23:20 +0000 (07:23 +0000)]
ARM: shmobile: r8a7791: add MMCIF max-frequency
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Thu, 14 May 2015 07:23:04 +0000 (07:23 +0000)]
ARM: shmobile: r8a7790: add MMCIF max-frequency
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Arnd Bergmann [Fri, 22 May 2015 15:33:12 +0000 (17:33 +0200)]
Merge branch 'for-upstream/juno-dts' of git://linux-arm.org/linux-ld into next/dt
Merge "Documentation: bindings: Add DT bindings for ARM Juno boards" from Liviu Dudau:
* 'for-upstream/juno-dts' of git://linux-arm.org/linux-ld:
Documentation: bindings: Add DT bindings for ARM Juno boards.
arm64: Add DT support for Juno r1 board.
arm64: Juno: Add GICv2m support in device tree.
arm64: Juno: Add memory mapped timer node
arm64: Juno: Split juno.dts into juno-base.dtsi and juno.dts.
arm64: Juno: Fix the GIC node address label and the frequency of FAXI clock.
Liviu Dudau [Wed, 20 May 2015 10:42:37 +0000 (11:42 +0100)]
Documentation: bindings: Add DT bindings for ARM Juno boards.
List the required properties and nodes used to describe the
ARM Juno boards.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Liviu Dudau [Tue, 10 Mar 2015 15:31:37 +0000 (15:31 +0000)]
arm64: Add DT support for Juno r1 board.
This board is based on Juno r0 with updated Cortex A5x revisions
and board errata fixes. It also contains coherent ThinLinks ports
on the expansion slot that allow for an AXI master on the daughter
card to participate in a coherency domain.
Support for SoC PCIe host bridge will be added as a separate series.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Liviu Dudau [Thu, 26 Mar 2015 12:16:31 +0000 (12:16 +0000)]
arm64: Juno: Add GICv2m support in device tree.
Juno contains a GICv2m extension for handling PCIe MSI messages.
Add a node declaring the first frame of the extension.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Liviu Dudau [Tue, 10 Mar 2015 15:21:23 +0000 (15:21 +0000)]
arm64: Juno: Add memory mapped timer node
Juno based boards have a memory mapped timer @ 0x2a810000. This
is disabled on r0 version of the board due to an SoC errata.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Liviu Dudau [Tue, 10 Mar 2015 15:18:18 +0000 (15:18 +0000)]
arm64: Juno: Split juno.dts into juno-base.dtsi and juno.dts.
Prepare the device tree for adding more boards based on Juno r0.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Liviu Dudau [Thu, 30 Apr 2015 15:45:57 +0000 (16:45 +0100)]
arm64: Juno: Fix the GIC node address label and the frequency of FAXI clock.
During the review of the Juno DT files I've noticed that the GIC
node label had two digits swapped leading to a different address
being shown in the /sys/devices fs.
Sudeep also pointed that public revisions of the Juno documentation
list a different frequency for the FAXI system than what the one
I've been using when creating the DT file. Verified with the firmware
people to be the correct value in the shipped systems.
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Jon Medhurst <tixy@linaro.org>
Arnd Bergmann [Fri, 22 May 2015 15:17:17 +0000 (17:17 +0200)]
Merge tag 'at91-dt3' of git://git./linux/kernel/git/nferre/linux-at91 into next/dt
Merge "Third batch of DT changes for 4.2" from Nicolas Ferre:
- USB host clock refine following changes in drivers
- one little fix for usart pinctrl
* tag 'at91-dt3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: remove useless usb clock
ARM: at91/dt: remove useless uhpck clock references from ehci defintions
USB: atmel: update DT bindings documentation
ARM: at91/dt: at91sam9x5: fix usart1 sck pin definition
Arnd Bergmann [Fri, 22 May 2015 15:16:20 +0000 (17:16 +0200)]
Merge tag 'v4.2-rockchip-dts2' of git://git./linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: dts relicensing for 4.2" from Heiko Stuebner:
Relicense all Rockchip-related devicetree files to the GPL2/X11 combo.
I've now finally aquired necessary Acks from all contributors.
* tag 'v4.2-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: relicense rk3288-evb* under GPLv2/X11
ARM: dts: rockchip: relicense rk3288.dtsi under GPLv2/X11
ARM: dts: rockchip: relicense rk3188-radxarock.dts under GPLv2/X11
ARM: dts: rockchip: relicense rk3066a-bqcurie2.dts under GPLv2/X11
ARM: dts: rockchip: relicense rk3288-thermal.dtsi under GPLv2/X11
ARM: dts: rockchip: relicense rk3188.dtsi under GPLv2/X11
ARM: dts: rockchip: relicense rk3066a.dtsi under GPLv2/X11
ARM: dts: rockchip: relicense rk3xxx.dtsi under GPLv2/X11
Boris Brezillon [Tue, 17 Mar 2015 16:15:50 +0000 (17:15 +0100)]
ARM: at91/dt: remove useless usb clock
The ohci driver now calls clk_set_rate on the uhpck clock (which forwards
set_rate requests to its parent: the usb clock).
Remove useless references to usb clocks from ohci definitions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris Brezillon [Tue, 17 Mar 2015 16:15:49 +0000 (17:15 +0100)]
ARM: at91/dt: remove useless uhpck clock references from ehci defintions
The uhpck is useless for High-Speed communications, remove the reference
to this clock in all ehci definitions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris Brezillon [Tue, 17 Mar 2015 16:15:48 +0000 (17:15 +0100)]
USB: atmel: update DT bindings documentation
Add documentation for the missing clocks, clock-names, reg and interrupts
properties.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Eyal Reizer [Sun, 3 May 2015 12:19:28 +0000 (15:19 +0300)]
ARM: dts: am335x-evm: add mmc3 and wlan definitions to dts
This includes the wlan regulator, pinmux, DMA
and wlcore bindings.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Geert Uytterhoeven [Wed, 20 May 2015 18:16:51 +0000 (20:16 +0200)]
ARM: shmobile: bockw dts: Replace "nor-jedec" by "jedec,spi-nor"
Cfr. commit
8947e396a8296c52 ('Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"')
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven [Wed, 20 May 2015 18:16:53 +0000 (20:16 +0200)]
ARM: shmobile: henninger dts: Replace "nor-jedec" by "jedec,spi-nor"
Cfr. commit
8947e396a8296c52 ('Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"')
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven [Wed, 20 May 2015 18:16:50 +0000 (20:16 +0200)]
ARM: shmobile: bockw-reference dts: Replace "nor-jedec" by "jedec,spi-nor"
Cfr. commit
8947e396a8296c52 ('Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"')
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven [Wed, 20 May 2015 18:16:54 +0000 (20:16 +0200)]
ARM: shmobile: koelsch dts: Replace "nor-jedec" by "jedec,spi-nor"
Cfr. commit
8947e396a8296c52 ('Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"')
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven [Wed, 20 May 2015 18:16:52 +0000 (20:16 +0200)]
ARM: shmobile: lager dts: Replace "nor-jedec" by "jedec,spi-nor"
Cfr. commit
8947e396a8296c52 ('Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"')
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tony Lindgren [Wed, 20 May 2015 21:48:35 +0000 (14:48 -0700)]
ARM: dts: Enable SDIO card interrupt for 37xx-evm
This allows to use the MMC1 slot with SDIO cards.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Wed, 20 May 2015 21:48:34 +0000 (14:48 -0700)]
ARM: dts: Fix ldp gpio keys to use defines
Fix ldp gpio keys to use defines.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Stefan Agner [Tue, 19 May 2015 22:05:18 +0000 (00:05 +0200)]
ARM: dts: add support for Vybrid running on Cortex-M4
This adds an initial device tree to run Linux on the Cortex-M4 on
the Vybrid based Colibri VF61 module.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 20 May 2015 21:03:25 +0000 (23:03 +0200)]
Merge tag 'berlin-dt-4.2-1' of git://git.infradead.org/users/hesselba/linux-berlin into next/dt
Merge "Berlin DT changes for v4.2" from Sebastian Hesselbarth:
- GPLv2/X11 dual licensing
- Mark Berlin DT bindings as unstable
- Updated binding documentation for reworked
chip/system ctrl nodes
* tag 'berlin-dt-4.2-1' of git://git.infradead.org/users/hesselba/linux-berlin:
Documentation: bindings: update the berlin chip and system ctrl doc
Documentation: bindings: move the Berlin clock documentation
Documentation: bindings: move the Berlin pinctrl documentation
Documentation: bindings: move the Berlin reset documentation
Documentation: bindings: update the Berlin controllers documentation
Documentation: bindings: berlin: consider our dt bindings as unstable
ARM: dts: berlin: relicense the BG2CD Google Chromecast dts under GPLv2/X11
ARM: dts: berlin: relicense the berlin2cd dtsi under GPLv2/X11
ARM: dts: berlin: relicense the BG2 Sony NSZ-GS7 dts under GPLv2/X11
ARM: dts: berlin: relicense the berlin2 dtsi under GPLv2/X11
ARM: dts: berlin: relicense the BG2Q Marvell DMP dts under GPLv2/X11
ARM: dts: berlin: relicense the berlin2q dtsi under GPLv2/X11
Pantelis Antoniou [Wed, 13 May 2015 08:04:34 +0000 (11:04 +0300)]
ARM: dts: Beaglebone i2c definitions
The beaglebone family of boards contain two I2C busses enabled.
The first one with a baseboard identification EEPROM and a
cape I2C bus.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Lad, Prabhakar [Thu, 12 Mar 2015 23:38:21 +0000 (23:38 +0000)]
ARM: dts: am437x-gp-evm: add DT nodes for ov2659 sensor
this patch does the following:
1: adds DT node for fixed oscillator.
2: adds DT node entries for ov2659 sensor
3: adds remote-endpoint entry for VPFE.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Yegor Yefremov [Tue, 19 May 2015 08:29:48 +0000 (10:29 +0200)]
ARM: dts: add DTS for Baltos IR5221
This device is an industrial PC based on
AM335x SoC.
[ balbi@ti.com : updated to fit current mainline ]
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Fri, 15 May 2015 22:16:40 +0000 (17:16 -0500)]
ARM: dts: omap5-uevm: Add Uart wakeup interrupt
UART3 wakeup takes place with iodaisy chain. enable the wakeup pin.
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: tabify uart pins properly while at it]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Marek Belisko [Thu, 7 May 2015 19:35:05 +0000 (21:35 +0200)]
ARM: dts: omap3-gta04: Add GSM audio support
Add voice audio card which is used for telephony on gta04 board.
gtm601 codec is UMTS modem with pcm interface which get samples from
microphone and provide data from other party side. Use simple audio card
to describe audio card.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliad Peller [Mon, 4 May 2015 12:41:13 +0000 (15:41 +0300)]
ARM: dts: am335x-evm: add bluetooth support
uart1 is used for connecting to wilink8 bluetooth subsystem.
add the needed muxes and definitions.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eyal Reizer [Mon, 4 May 2015 12:24:24 +0000 (15:24 +0300)]
ARM: dts: am437x-gp-evm: add wilink8 support
enable mmc3 used for wlan and uart3 used for bluetooth
configure the gpios used for wlan and bluetooth controls
add fixed voltage regulator used for wlan power control
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Marek Belisko [Tue, 28 Apr 2015 20:54:27 +0000 (22:54 +0200)]
ARM: dts: omap3-gta04: Add hdqw1 support
Enable omap-hdq for battery fuel gauge access.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Andrey Skvortsov [Sun, 10 May 2015 21:27:53 +0000 (00:27 +0300)]
ARM: dts: add core2 padconf region for am3517
According to the technical reference manual for AM35xx system
controller module (SCM) PADCONFS core registers are divided in two
regions: 0x48002030..0x48002268 and 0x480025d8..0x480025fc.
First region is the same for all omap3 SoC and is described in omap3.dtsi.
The second region is the same as in omap34xx (see omap34xx.dtsi)
and omap35xx. The patch adds missing description for the second region.
This patch was tested on AM3517.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Wed, 20 May 2015 16:23:43 +0000 (09:23 -0700)]
ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit
The LogicPD Torpedo DM3730 devkit consists of a base board and
two processor boards. One of the processor boards has a WLAN and
the other one does not.
Let's set up basic dts file so we can move to device tree only
based booting over next few merge windows. So far I've tested
that UARTs, MMC1, USB OTG, smsc911x, and basic PM support works.
Note that the wireless support in kernel for wl1283 seems to be
broken, it tries to load wl127x-nvs.bin instead of wl128x-nvs.bin
with firmware.
Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Wed, 20 May 2015 16:23:43 +0000 (09:23 -0700)]
ARM: OMAP3: Add support for configuring MMC pins as GPIO pins
Some devices are using the MMC1 pins 4..8 as GPIO pins, and in
this case they need to be configured for 1.8V IO voltage if not
done by the bootloader as otherwise some devices like smsc911x
won't work properly.
Let's also make sure this register is saved and restored for
idle.
Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Arnd Bergmann [Wed, 20 May 2015 15:38:02 +0000 (17:38 +0200)]
Merge tag 'at91-dt2' of git://git./linux/kernel/git/nferre/linux-at91 into next/dt
Merge "Second batch of DT changes for 4.2:" from Nicolas Ferre:
- sama5d4: more peripherals: usarts, uarts, spi, pioD access
- sama5d3: phy address for gmac
- change NFC register map
- regulator additions for the sd/mmc
* tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sama5d4 xplained: add regulators for v(q)mmc1 supplies
ARM: at91/dt: sama5d3 xplained: add fixed regulator for vmmc0
ARM: at91/dt: sama5d3 xplained: add mmc0 vqmmc entry
ARM: at91/dt: sama5d3 xplained: fill in mmc1 and set it to disabled
ARM: at91/dt: sama5: reduce the NFC command register map
ARM: at91/dt: sama5d4: update pinctrl ranges
ARM: at91/dt: sama5d3 xplained: add phy address for macb0
ARM: at91/dt: sama5d4 xplained: add spi1 on j14 connector
ARM: at91/dt: sama5d4: add spi1, spi2 dt nodes
ARM: at91/dt: sama5d4: add uart0, uart1 dt nodes
ARM: at91/dt: sama5d4: add usart0, usart1 dt nodes
Nicolas Ferre [Wed, 20 May 2015 12:31:49 +0000 (14:31 +0200)]
ARM: at91/dt: at91sam9x5: fix usart1 sck pin definition
SCK1 pin is pioC 29. Comment was okay.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Ludovic Desroches [Mon, 27 Apr 2015 13:27:52 +0000 (15:27 +0200)]
ARM: at91/dt: sama5d4 xplained: add regulators for v(q)mmc1 supplies
Add vcc_mmc1 fixed regulator to remove the 'no vmmc regulator found' warning
when probing the mmc1 device.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Ben Dooks [Mon, 27 Apr 2015 13:19:12 +0000 (15:19 +0200)]
ARM: at91/dt: sama5d3 xplained: add fixed regulator for vmmc0
Add fixed regulator for vmmc0 and attach the vmmc for it to the mmc0
node on the SAM5D3 Xplained board. This will remove the following
warning from the kernel:
atmel_mci
f0000000.mmc: No vmmc regulator found
Note, atmel_defconfig will need fixed regulator support enabled if this
is to be used properly.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[use a fixed regulator instead of gpio one]
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Ben Dooks [Mon, 27 Apr 2015 13:19:11 +0000 (15:19 +0200)]
ARM: at91/dt: sama5d3 xplained: add mmc0 vqmmc entry
The SAM5D3 Xplained device tree is missing the vqmmc node which is
tied to 3.3V on the board. Add this to avoid the kernel warning that
there is no vqmmc node.
atmel_mci
f0000000.mmc: No vqmmc regulator found
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Ben Dooks [Mon, 27 Apr 2015 13:19:10 +0000 (15:19 +0200)]
ARM: at91/dt: sama5d3 xplained: fill in mmc1 and set it to disabled
The mmc1 channel is not populated on the SAM5D3 Xplained board, however
it is enabled and therefore the driver is attaching to it.
The node configuration for mmc1 is missing, so add an mmc1 node in the
device tree and set its status to disabled. Also add the vmmc and the
necessary slot configuration if this node were enabled to avoid the following
warnings from the driver:
atmel_mci
f8000000.mmc: No vmmc regulator found
atmel_mci
f8000000.mmc: No vqmmc regulator found
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Josh Wu [Thu, 2 Apr 2015 06:17:56 +0000 (14:17 +0800)]
ARM: at91/dt: sama5: reduce the NFC command register map
commit
111573ccd89b ("mtd: atmel_nand: check NFC busy flag by HSMC_SR
instead of NFC cmd regs")
check NFC busy by nfc SR instead of NFC cmd regs. So we don't need to
map NFC cmd registers to include NFCBUSY bit.
That means we only need map 0x08000000 instead of 0x10000000 for NFC
cmd regs.
This patch reduce the NFC cmd regs map for sama5d3 & sama5d4.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Ludovic Desroches [Mon, 27 Apr 2015 09:15:06 +0000 (11:15 +0200)]
ARM: at91/dt: sama5d4: update pinctrl ranges
Update the pinctrl ranges property to support pioD controller whose
mapping is not contiguous with other pio controllers. Without this
update, getting resource will fail, then pinctrl probe will fail too
because there is a missing pio controller.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Ferre [Tue, 31 Mar 2015 09:01:12 +0000 (11:01 +0200)]
ARM: at91/dt: sama5d3 xplained: add phy address for macb0
Specify the phy address on macb0 node aka GEM.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Ferre [Mon, 18 May 2015 10:18:03 +0000 (12:18 +0200)]
ARM: at91/dt: sama5d4 xplained: add spi1 on j14 connector
Route SPI1 on the Arduino "in the middle" spi connector.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Suchang Ko [Tue, 12 May 2015 06:34:43 +0000 (15:34 +0900)]
ARM: at91/dt: sama5d4: add spi1, spi2 dt nodes
Add sama5d4 spi1, spi2 dt nodes & pinctrl.
Signed-off-by: Suchang Ko <suchangko@samul.kr>
[nicolas.ferre@atmel.com: split patch, reorder & whitespace fixes]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Yingjoe Chen [Sat, 16 May 2015 07:30:11 +0000 (15:30 +0800)]
ARM: dts: mt8127: correct uart instance address
The instance address for uart nodes are incorrect. Correct them.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Antoine Tenart [Tue, 7 Apr 2015 14:45:06 +0000 (16:45 +0200)]
Documentation: bindings: update the berlin chip and system ctrl doc
Now that the rework to have one sub-node per device in the chip and
system controllers is done, their dedicated compatible can be removed.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Antoine Tenart [Tue, 7 Apr 2015 14:45:02 +0000 (16:45 +0200)]
Documentation: bindings: move the Berlin clock documentation
The Berlin clock documentation was part of the Marvell Berlin SoC
documentation because the Berlin clock configuration was inside the
chip controller. With the recent rework of the chip and system
controller handling (now all sub-devices of the soc and system
controller nodes are registred with simple-mfd, and each device has its
own sub-node), the documentation of the Berlin clock driver can be moved
to the generic clock documentation directory.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Antoine Tenart [Mon, 27 Apr 2015 19:39:48 +0000 (21:39 +0200)]
Documentation: bindings: move the Berlin pinctrl documentation
The Berlin pinctrl documentation was part of the Marvell Berlin SoC
documentation because the Berlin pinctrl configuration was inside the
chip and the system controllers. With the recent rework of the chip and
system controller handling (now an MFD driver registers all sub-devices
of the two soc and system controller nodes and each device has its own
sub-node), the documentation of the Berlin pinctrl driver can be moved
to the generic pinctrl documentation directory.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Antoine Tenart [Mon, 27 Apr 2015 19:39:48 +0000 (21:39 +0200)]
Documentation: bindings: move the Berlin reset documentation
The Berlin reset documentation was part of the Marvell Berlin SoC
documentation because the Berlin reset configuration was inside the chip
controller. With the recent rework of the chip and system controller
handling (now an MFD driver registers all sub-devices of the two soc and
system controller nodes and each device has its own sub-node), the
documentation of the Berlin reset driver can be moved to the generic
reset documentation directory.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Antoine Tenart [Mon, 27 Apr 2015 19:39:48 +0000 (21:39 +0200)]
Documentation: bindings: update the Berlin controllers documentation
We're moving from a single node for multiple devices to a node with one
sub-node per sub-device, registered by simple-mfd. Update the
documentation to reflect the changes.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Antoine Tenart [Mon, 27 Apr 2015 19:39:47 +0000 (21:39 +0200)]
Documentation: bindings: berlin: consider our dt bindings as unstable
Because the support of Marvell Berlin SoCs is still a work in progress,
add a statement to explicitly consider our device tree files and
bindings as unstable.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Antoine Tenart [Mon, 27 Apr 2015 19:39:47 +0000 (21:39 +0200)]
ARM: dts: berlin: relicense the BG2CD Google Chromecast dts under GPLv2/X11
The current GPLv2 only licensing on this dts makes it very impractical
for other software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense
this dts under a GPLv2/X11 dual-license.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Antoine Tenart [Mon, 27 Apr 2015 19:39:47 +0000 (21:39 +0200)]
ARM: dts: berlin: relicense the berlin2cd dtsi under GPLv2/X11
The current GPLv2 only licensing on this dtsi makes it very impractical
for other software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense
this dtsi under a GPLv2/X11 dual-license.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Antoine Tenart [Mon, 27 Apr 2015 19:39:47 +0000 (21:39 +0200)]
ARM: dts: berlin: relicense the BG2 Sony NSZ-GS7 dts under GPLv2/X11
The current GPLv2 only licensing on this dts makes it very impractical
for other software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense
this dts under a GPLv2/X11 dual-license.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Antoine Tenart [Mon, 27 Apr 2015 19:39:47 +0000 (21:39 +0200)]
ARM: dts: berlin: relicense the berlin2 dtsi under GPLv2/X11
The current GPLv2 only licensing on this dtsi makes it very impractical
for other software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense
this dtsi under a GPLv2/X11 dual-license.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Antoine Tenart [Mon, 27 Apr 2015 19:39:46 +0000 (21:39 +0200)]
ARM: dts: berlin: relicense the BG2Q Marvell DMP dts under GPLv2/X11
The current GPLv2 only licensing on this dts makes it very impractical
for other software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense
this dts under a GPLv2/X11 dual-license.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Antoine Tenart [Mon, 27 Apr 2015 19:39:46 +0000 (21:39 +0200)]
ARM: dts: berlin: relicense the berlin2q dtsi under GPLv2/X11
The current GPLv2 only licensing on this dtsi makes it very impractical
for other software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense
this dtsi under a GPLv2/X11 dual-license.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Ariel D'Alessandro [Mon, 11 May 2015 22:00:52 +0000 (00:00 +0200)]
ARM: dts: Add DT for Hitex LPC4350 Evaluation Board
Add basic support for Hitex LPC4350 Evaluation Board. Board
features a LPC4350 Soc, 8 MB SDRAM, 8 MB SPI Flash, USB and
Ethernet.
More information can be found on:
http://www.hitex.com/index.php?id=3212
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@gmail.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Joachim Eastwood [Mon, 11 May 2015 22:00:51 +0000 (00:00 +0200)]
ARM: dts: Add DT for Embedded Artists LPC4357 Developers Kit
Adds basic support for Embedded Artists' LPC4357 Developer's Kit. Board
features a LPC4357 Soc, 32 MB SDRAM, 128 MB NAND Flash, 16 MB SPI
Flash, USB and Ethernet.
More information can be found on:
http://www.embeddedartists.com/products/kits/lpc4357_kit.php
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Joachim Eastwood [Mon, 11 May 2015 22:00:50 +0000 (00:00 +0200)]
ARM: dts: Add base DT for NXP LPC18xx
NXP LPC18xx/43xx SoCs are very similar devices and should be able to
share a common base (lpc18xx.dtsi). Diffences between the devices are
put in a dtsi which is specific to that device.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Maxime Coquelin [Sat, 9 May 2015 07:53:55 +0000 (09:53 +0200)]
ARM: dts: Add ARM System timer as clocksource in armv7m
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 15 May 2015 15:27:55 +0000 (17:27 +0200)]
Merge tag 'mvebu-dt-4.2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu dt changes for v4.2 (part #1)" from Gregory CLEMENT:
- A series adding support for the Compulab CM-A510
- Add alias for mdio on Armada 38x
* tag 'mvebu-dt-4.2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add alias for mdio on Armada 38x
ARM: dts: dove: Add Compulab SBC-A510 to Makefile
ARM: dts: dove: Add proper support for Compulab CM-A510/SBC-A510
ARM: dts: dove: Remove Compulab CM-A510 from Makefile
ARM: dts: dove: Add internal i2c multiplexer node
Arnd Bergmann [Fri, 15 May 2015 15:26:31 +0000 (17:26 +0200)]
Merge tag 'sti-dt-for-v4.2-2' of git://git./linux/kernel/git/mcoquelin/sti into next/dt
Merge "STi DT updates for v4.2, round 2." from Maxime Coquelin:
Highlights:
-----------
- Add USB3 support to STiH410 & STiH418
- Add PWM support to STiH416 & STiH407 family
- Add restart support to STiH416 & STiH407 family
- Add PMU support to STiH416 & STiH407 family
- Reorder includes in STiH407 DT files
* tag 'sti-dt-for-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti:
ARM: STi: DT: STih407: Re-order #include <*.dtsi> files
ARM: STi: Ensure requested STi's SysCfg Controlled IRQs are enabled at boot
ARM: STi: STiH407: Enable PMU IRQs
ARM: STi: STiH407: Enable Cortex-A9 PMU support
ARM: STi: STiH416: Enable PMU IRQs
ARM: STi: STiH416: Enable Cortex-A9 PMU support
ARM: STi: STiH416: Add Restart support for STiH416
ARM: STi: STiH407: Add Restart support for STiH407
ARM: STi: STiH416-b2020e: Enable PWM on the B2020 Rev-E
ARM: STi: STiH416: Add DT nodes for PWM
ARM: STi: STiH416: Add Pinctrl settings for PWM
ARM: STi: STiH407: Add DT nodes for for PWM
ARM: DT: STi: STiH418: Enable USB3 port on stih418-b2199.
ARM: DT: STi: STiH418: Add miphy28lp optional oscillator clock properties
ARM: DT: STi: stihxxx-b2120: Enable USB3 port on stih407-b2120 and stih410-b2120
ARM: DT: STi: STiH407: Add dwc3 usb3 DT node.
ARM: DT: STi: STiH407: Update picophyreset for the usb3 controllers usb2 phy
Arnd Bergmann [Fri, 15 May 2015 15:23:29 +0000 (17:23 +0200)]
Merge tag 'rpi-dt-for-armsoc-v4.2' of git://git./linux/kernel/git/rpi/linux-rpi into next/dt
Merge "RaspberryPi Device Tree changes due for v4.2" from Lee Jones:
* tag 'rpi-dt-for-armsoc-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rpi/linux-rpi:
ARM: bcm2835: dt: Use 0x4 prefix for DMA bus addresses to SDRAM.
ARM: bcm2835: dt: Add the mailbox to the device tree
ARM: bcm2835: dt: Fix i2c0 node name
ARM: bcm2835: dt: Use pinctrl header
ARM: bcm2835: dt: Add header file for pinctrl constants
ARM: bcm2835: dt: Add root properties for Raspberry Pi
ARM: bcm2835: dt: Add vendor prefix for Raspberry Pi
Linus Walleij [Thu, 14 May 2015 09:22:34 +0000 (11:22 +0200)]
ARM: ux500: add SCU and WD to device tree
The Ux500 like other Cortex-A9 SoC's has a Snoop Control
Unit (SCU) and a Watchdog in the same address range as
the local timers. Add these to the SoC device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 15 May 2015 15:21:10 +0000 (17:21 +0200)]
Merge tag 'renesas-dt-for-v4.2' of git://git./linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.2" from Simon Horman:
* Enable DMA for HSUSB on r8a7790 and r8a7791 SoCs
* Configure the HOME key as wake-up source on kzm9g board
* Use generic names for device nodes on SH Mobile SoCs and boards
* Add "nor-jedec" compatible value to SH Mobile boards
* Add IRQC clock to r8a73a4, r8a779* SoCs
* Remove MSIOF address from r8a7790 and r8a7791 SoCs
* tag 'renesas-dt-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
ARM: shmobile: r8a7791: Enable DMA for HSUSB
ARM: shmobile: r8a7791: add USB-DMAC device nodes
ARM: shmobile: r8a7790: Enable DMA for HSUSB
ARM: shmobile: r8a7790: add USB-DMAC device nodes
ARM: shmobile: kzm9g dts: Configure the HOME key as wake-up source
ARM: shmobile: koelsch dts: Use generic names for device nodes
ARM: shmobile: lager dts: Use generic names for device nodes
ARM: shmobile: bockw dts: Use generic names for device nodes
ARM: shmobile: koelsch dts: Add "nor-jedec" compatible value
ARM: shmobile: bockw dts: Add "nor-jedec" compatible value
ARM: shmobile: lager dts: Add "nor-jedec" compatible value
ARM: shmobile: bockw-reference dts: Add "nor-jedec" compatible value
ARM: shmobile: henninger dts: Add "nor-jedec" compatible value
ARM: shmobile: armadillo800eva dts: Use generic names for device nodes
ARM: shmobile: marzen dts: Use generic names for device nodes
ARM: shmobile: kzm9d dts: Use generic names for device nodes
ARM: shmobile: ape6evm dts: Use generic names for device nodes
ARM: shmobile: sh73a0 dtsi: Use generic names for device nodes
ARM: shmobile: r8a7791 dtsi: Use generic names for device nodes
ARM: shmobile: r8a7790 dtsi: Use generic names for device nodes
...
Arnd Bergmann [Fri, 15 May 2015 15:18:57 +0000 (17:18 +0200)]
Merge tag 'pxa-dt-4.2' of https://github.com/rjarzmik/linux into next/dt
Merge "device-tree pxa update" from Robert Jarzmik:
- clocks descriptions (pxa27x, pxa3xx)
- timer descriptions (pxa27x, pxa3xx)
- IPs which are embedded on the SoC
- keypad
- udc (USB client)
- power I2C
These are amongst the building blocks for future pxa device-tree board
description.
* tag 'pxa-dt-4.2' of https://github.com/rjarzmik/linux:
ARM: dts: pxa: add pxa-timer to pxa27x and pxa3xx
ARM: dts: pxa: add pxa27x-keypad to pxa27x
ARM: dts: pxa: add pxa27x-udc to pxa27x
ARM: dts: pxa: add clocks
ARM: dts: pxa: add pwri2c to pxa device-tree
Arnd Bergmann [Fri, 15 May 2015 15:17:24 +0000 (17:17 +0200)]
Merge tag 'arm-soc/for-4.2/dts' of github.com/broadcom/stblinux into next/dt
Merge "Device Tree changes" from Florian Fainelli:
New devices:
- Felix adds support for the Buffalo WXR-1900DHP and adds the USB led on Buffalo
WZR-1750DHP
- Rafal adds support for the SmartRG SR400ac, Asus RT-AC68U and RT-AC56U
New peripheral support:
- Brian adds Device Tree nodes for the Broadcom NAND controller found on
BCM7xxx, BCM63138 and Cygnus SoCs
- Brian adds Device Tree nodes for the SATA AHCI and PHY controller found on
BCM7xxx
- I add the Device Tree nodes and bindings documents for bringing-up secondary
CPUs and timer/syscon-reboot on BCM63138
* tag 'arm-soc/for-4.2/dts' of http://github.com/broadcom/stblinux:
ARM: BCM5301X: Add DT for Asus RT-AC56U
ARM: BCM5301X: Add DT for Asus RT-AC68U
ARM: dts: BCM63xx: Add timer and syscon-reboot nodes
dt-bindings: Add documentation for the BCM63138 timer and syscon-reboot
ARM: dts: brcmstb: add nodes for SATA controller and PHY
ARM: dts: cygnus: Enable NAND support for Cygnus
ARM: bcm63138: add NAND DT support
ARM: bcm7445: add NAND to DTS
ARM: BCM5301X: Add DT for SmartRG SR400ac
ARM: BCM5301X: Add DT for Buffalo WXR-1900DHP
ARM: BCM5301X: Add USB LED for Buffalo WZR-1750DHP
ARM: dts: BCM63xx: Add SMP nodes and required properties
Documentation: DT: Document SMP DT nodes and properties for BCM63138
ARM: dts: BCM63xx: Add PMB busses nodes
Documentation: DT: Add Broadcom BCM63138 PMB binding
Heiko Stuebner [Fri, 6 Mar 2015 18:04:06 +0000 (19:04 +0100)]
ARM: dts: rockchip: relicense rk3288-evb* under GPLv2/X11
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3288-evb files to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Caesar Wang <caesar.wang@rock-chips.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Chris Zhong<zyw@rock-chips.com>
Acked-by: Roger Chen <roger.chen@rock-chips.com>
Acked-by: Yunzhi Li <lyz@rock-chips.com>
on behalf of Rockchip
Acked-by: Eddie Cai <eddie.cai@rock-chips.com>
Heiko Stuebner [Fri, 6 Mar 2015 18:04:02 +0000 (19:04 +0100)]
ARM: dts: rockchip: relicense rk3288.dtsi under GPLv2/X11
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3288.dtsi to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Doug Anderson <dianders@chromium.org>
Acked-by: Sonny Rao <sonnyrao@chromium.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Caesar Wang <caesar.wang@rock-chips.com>
Acked-by: Lin Huang <hl@rock-chips.com>
Acked-by: Chris Zhong <zyw@rock-chips.com>
Acked-by: Jianqun Xu<jay.xu@rock-chips.com>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Roger Chen <roger.chen@rock-chips.com>
Acked-by: Yunzhi Li <lyz@rock-chips.com>
on behalf of Rockchip
Acked-by: Eddie Cai <eddie.cai@rock-chips.com>
Lee Jones [Mon, 11 May 2015 14:12:00 +0000 (16:12 +0200)]
ARM: STi: DT: STih407: Re-order #include <*.dtsi> files
This patch fixes a regression where serial is enabled by the first
(board) DTSI, then disabled by the second (SoC) file. To enable
serial and keep it enabled, we need to include the file which enables
it last.
Reported-by: LAVA [via Peter Griffin <peter.griffin@linaro.org>]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Eric Anholt [Tue, 5 May 2015 20:10:11 +0000 (13:10 -0700)]
ARM: bcm2835: dt: Use 0x4 prefix for DMA bus addresses to SDRAM.
There exists a tiny MMU, configurable only by the VC (running the
closed firmware), which maps from the ARM's physical addresses to bus
addresses. These bus addresses determine the caching behavior in the
VC's L1/L2 (note: separate from the ARM's L1/L2) according to the top
2 bits. The bits in the bus address mean:
From the VideoCore processor:
0x0... L1 and L2 cache allocating and coherent
0x4... L1 non-allocating, but coherent. L2 allocating and coherent
0x8... L1 non-allocating, but coherent. L2 non-allocating, but coherent
0xc... SDRAM alias. Cache is bypassed. Not L1 or L2 allocating or coherent
From the GPU peripherals (note: all peripherals bypass the L1
cache. The ARM will see this view once through the VC MMU):
0x0... Do not use
0x4... L1 non-allocating, and incoherent. L2 allocating and coherent.
0x8... L1 non-allocating, and incoherent. L2 non-allocating, but coherent
0xc... SDRAM alias. Cache is bypassed. Not L1 or L2 allocating or coherent
The 2835 firmware always configures the MMU to turn ARM physical
addresses with 0x0 top bits to 0x4, meaning present in L2 but
incoherent with L1. However, any bus addresses we were generating in
the kernel to be passed to a device had 0x0 bits. That would be a
reserved (possibly totally incoherent) value if sent to a GPU
peripheral like USB, or L1 allocating if sent to the VC (like a
firmware property request). By setting dma-ranges, all of the devices
below it get a dev->dma_pfn_offset, so that dma_alloc_coherent() and
friends return addresses with 0x4 bits and avoid cache incoherency.
This matches the behavior in the downstream 2708 kernel (see
BUS_OFFSET in arch/arm/mach-bcm2708/include/mach/memory.h).
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Eric Anholt [Tue, 5 May 2015 20:27:46 +0000 (13:27 -0700)]
ARM: bcm2835: dt: Add the mailbox to the device tree
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Baruch Siach [Wed, 18 Mar 2015 09:00:22 +0000 (11:00 +0200)]
ARM: bcm2835: dt: Fix i2c0 node name
Device tree node names should contain the node's reg property address value.
The i2c0 node was apparently forgotten in commit
25b2f1bd0b7e0 (ARM: bcm2835:
node name unit address cleanup).
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Stefan Wahren [Thu, 29 Jan 2015 18:10:50 +0000 (18:10 +0000)]
ARM: bcm2835: dt: Use pinctrl header
This patch converts all bcm2835 dts and dtsi files to use the pinctrl
header file.
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Stefan Wahren [Thu, 29 Jan 2015 18:10:49 +0000 (18:10 +0000)]
ARM: bcm2835: dt: Add header file for pinctrl constants
This new header file defines pincontrol constants to use
from bcm2835 DTS files for pincontrol properties option.
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Stefan Wahren [Thu, 29 Jan 2015 18:10:48 +0000 (18:10 +0000)]
ARM: bcm2835: dt: Add root properties for Raspberry Pi
This patch adds root compatible properties for the following boards:
- Raspberry Pi Model A
- Raspberry Pi Model A+
- Raspberry Pi Model B
- Raspberry Pi Model B (no P5)
- Raspberry Pi Model B rev2
- Raspberry Pi Model B+
- Raspberry Pi Compute Module
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Stefan Wahren [Thu, 29 Jan 2015 18:10:47 +0000 (18:10 +0000)]
ARM: bcm2835: dt: Add vendor prefix for Raspberry Pi
Since the prefix is already in use, we need to add it in the
vendor list.
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Heiko Stuebner [Fri, 6 Mar 2015 18:04:05 +0000 (19:04 +0100)]
ARM: dts: rockchip: relicense rk3188-radxarock.dts under GPLv2/X11
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3188-radxarock.dts to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Julien Chauveau <chauveau.julien@gmail.com>
Heiko Stuebner [Fri, 6 Mar 2015 18:04:04 +0000 (19:04 +0100)]
ARM: dts: rockchip: relicense rk3066a-bqcurie2.dts under GPLv2/X11
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3066a-bqcurie2.dts to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Heiko Stuebner [Fri, 6 Mar 2015 18:04:03 +0000 (19:04 +0100)]
ARM: dts: rockchip: relicense rk3288-thermal.dtsi under GPLv2/X11
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3288-thermal.dtsi to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Caesar Wang <caesar.wang@rock-chips.com>
Heiko Stuebner [Fri, 6 Mar 2015 18:04:01 +0000 (19:04 +0100)]
ARM: dts: rockchip: relicense rk3188.dtsi under GPLv2/X11
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3188.dtsi to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Julien Chauveau <chauveau.julien@gmail.com>
Acked-by: Max Schwarz <max.schwarz@online.de>