OSDN Git Service
Michael Trimarchi [Tue, 17 Jul 2018 09:25:26 +0000 (14:55 +0530)]
ARM: dts: imx6dl-mamoj: Add usb host and device support
Add USB host and device support for BTicino i.MX6DL Mamoj board.
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jagan Teki [Tue, 17 Jul 2018 09:25:25 +0000 (14:55 +0530)]
ARM: dts: imx6dl-mamoj: Add Wifi support
Add TI WL18XX Wifi for BTicino i.MX6DL board.
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jagan Teki [Tue, 17 Jul 2018 09:25:24 +0000 (14:55 +0530)]
ARM: dts: imx6dl-mamoj: Add parallel display support
This patch adds parallel display support for i.MX6DL Mamoj board
along with relevant backlight through pwm.
LCD power sequence is added by 'Michael Trimarchi'.
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Tue, 17 Jul 2018 04:06:51 +0000 (21:06 -0700)]
ARM: dts: vf610: Add ZII SSMB SPU3 board
Add support for Zodiac Inflight Innovations SSMB SPU3
board (VF610-based).
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 17 Jul 2018 02:08:45 +0000 (23:08 -0300)]
ARM: dts: imx6ul-pico-hobbit: Do not hardcode the memory size
There are two variants of imx6ul-pico boards: one with 256MB and
another one with 512MB of RAM.
Do not hardcode the memory size in the device tree and let the
bootloader fill the correct value instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Robin Gong [Tue, 17 Jul 2018 05:12:05 +0000 (13:12 +0800)]
ARM: dts: imx6sl-evk: make pfuze100 sw4 always on
On i.MX6SL EVK board, pfuze100 sw4 supplies
LPDDR2 which is critical for system, must be
always on.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Tue, 17 Jul 2018 05:12:04 +0000 (13:12 +0800)]
ARM: dts: imx6sll-evk: make pfuze100 sw4 always on
On i.MX6SLL EVK board, pfuze100 sw4 supplies
LPDDR3 which is critical for system, must be
always on.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Tue, 17 Jul 2018 05:12:03 +0000 (13:12 +0800)]
ARM: dts: imx6sx-sdb-reva: make pfuze100 sw4 always on
On i.MX6SX SDB Rev-A board, pfuze100 sw4 supplies
csi, audio codec and i2c etc., these modules do NOT
implement power domain control, so pfuze100 sw4
needs to be always on to make sure these modules
work normally.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Tue, 17 Jul 2018 05:12:02 +0000 (13:12 +0800)]
ARM: dts: imx6qdl-sabresd: make pfuze100 sw4 always on
On i.MX6QDL Sabre-SD board, pfuze100 sw4 supplies
GPS, touch and RGMII etc., these modules do NOT
implement power domain control, so pfuze100 sw4
needs to be always on to make sure these modules
work normally.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Sat, 14 Jul 2018 01:53:58 +0000 (09:53 +0800)]
ARM: dts: imx6sl-evk: add missing GPIO iomux setting
On i.MX6SL EVK board, the MX6SL_PAD_KEY_ROW5 pin is
used as lcd 3v3 regulator control pin, need to make
sure MX6SL_PAD_KEY_ROW5 is muxed as GPIO function
for controlling lcd 3v3 regulator.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by; Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Tue, 17 Jul 2018 06:44:38 +0000 (14:44 +0800)]
ARM: dts: imx51-zii-scu3-esb: Fix RAVE SP watchdog compatible string
It looks like I made a nasty typo in the original patch which resulted
in missing watchdog device. Fix it.
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Fri, 13 Jul 2018 17:30:04 +0000 (10:30 -0700)]
ARM: dts: imx51-zii-scu3-esb: Add switch IRQ line pinumx config
Instead of relying on default values, configure PAD_AUD3_BB_CK to be a
GPIO explicitly. While at, it change the pad configuration to enable
a 100K pull-down (the pin is used as IRQ_TYPE_LEVEL_HIGH).
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Fri, 13 Jul 2018 12:49:04 +0000 (14:49 +0200)]
ARM: dts: imx6sx-nitrogen6sx: remove obsolete display configuration
This display configuration isn't working as-is as it depends on the
tfp410 LCD to HDMI bridge. This will need to be updated later once
the DRM MXSFB driver will be the default.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Fri, 13 Jul 2018 12:49:03 +0000 (14:49 +0200)]
ARM: dts: imx7d-nitrogen7: use OF graph to describe the display
To make use of the new eLCDIF DRM driver OF graph description is
required. Describe the display using OF graph nodes.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Fri, 13 Jul 2018 12:49:02 +0000 (14:49 +0200)]
ARM: dts: imx: Switch Boundary Devices boards to SPDX identifier
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Leonard Crestez [Fri, 13 Jul 2018 09:39:35 +0000 (12:39 +0300)]
ARM: dts: imx6sl: Add vivante gpu nodes
The imx6sl soc has gpu_2d and gpu_vg, no 3d support:
etnaviv-gpu
2200000.gpu: model: GC320, revision: 5007
etnaviv-gpu
2204000.gpu: model: GC355, revision: 1215
The IP blocks seem to be already supported.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Fri, 13 Jul 2018 07:58:27 +0000 (15:58 +0800)]
ARM: dts: imx6sll-evk: enable SEIKO 43WVF1G lcdif panel
Enable SEIKO 43WVF1G lcdif panel for DRM driver,
add necessary properties according to SEIKO 43WVF1G
driver's requirement, such as "dvdd-supply", "avdd-supply"
and "backlight" etc..
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Fri, 13 Jul 2018 07:58:26 +0000 (15:58 +0800)]
ARM: dts: imx6sll-evk: correct lcd regulator GPIO pin
On i.MX6SLL EVK board, lcd regulator is controlled
by GPIO4 IO03 using MX6SLL_PAD_KEY_ROW5__GPIO4_IO03 pin,
NOT MX6SLL_PAD_ECSPI1_SCLK__GPIO4_IO08, correct it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Fri, 13 Jul 2018 07:58:25 +0000 (15:58 +0800)]
ARM: dts: imx6sll-evk: enable PWM1 for backlight driver
Enable pwm1 module on i.MX6SLL EVK board to make
backlight driver really work with LCD panel connected.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Thu, 12 Jul 2018 13:02:38 +0000 (10:02 -0300)]
ARM: dts: imx51-zii-rdu1: Enable secure-reg-access
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Thu, 12 Jul 2018 13:02:37 +0000 (10:02 -0300)]
ARM: dts: imx51-babbage: Enable secure-reg-access
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Sebastian Reichel [Thu, 12 Jul 2018 13:02:36 +0000 (10:02 -0300)]
ARM: dts: imx53-ppd: Enable secure-reg-access
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
[fabio: kept the change only in imx53-ppd context]
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alex Gonzalez [Thu, 12 Jul 2018 08:20:36 +0000 (10:20 +0200)]
ARM: dts: imx6ul: Add DTS for ConnectCore 6UL SBC Express
The ConnectCore 6UL Single Board Computer (SBC) Express contains the
ConnectCore 6UL System-On-Module.
Its hardware specifications are:
* 256MB DDR3 memory
* 256MB NAND flash
* Single Ethernet
* USB Host and USB-OTG
* MicroSD external storage
* Groove connectors and Raspberry Pi Hat compatible expansion header
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alex Gonzalez [Thu, 12 Jul 2018 08:20:35 +0000 (10:20 +0200)]
ARM: dts: imx6ul: Add DTS for ConnectCore 6UL System-On-Module (SOM)
The ConnectCore 6UL System-On-Module has the following hardware
specification:
* Based on a NXP i.MX6UL SoC
* Industrial temperature ranges (-40ºC to +85ºC)
* Up to 1GB DDR3 memory
* Up to 2GB NAND flash
* Dual Ethernet
* On module 802.11 WiFi and Bluetooth 4.2 (QCA6564)
* On module NXP Kinetis KL03
* On module Microchip ATECC508A crypto element
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 11 Jul 2018 21:34:27 +0000 (18:34 -0300)]
ARM: dts: imx51-zii-rdu1: Disable internal watchdog
imx51-zii-rdu1 has an external watchdog in the environment
microcontroller, so disable the internal one.
This aligns with what was done in commit
7055f714032c ("ARM: dts:
imx6: RDU2: disable internal watchdog") for imx6 rdu2 board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 10 Jul 2018 16:31:47 +0000 (13:31 -0300)]
ARM: dts: imx53: Add a label for the PMU node
Add a label for the PMU node so that the board dts may be able to
pass the 'secure-reg-access' property like this:
&pmu {
secure-reg-access;
};
This also makes it consistent with the PMU node in imx6qdl.dtsi
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 10 Jul 2018 16:31:46 +0000 (13:31 -0300)]
ARM: dts: imx53: Add tigerp support
As per the i.MX53 Reference Manual add an entry for the
'tigerp' region in the device tree.
This is needed for accessing the ARM_GPC register to set the
DBGEN bit, so that the debug clocks can be turned on.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 10 Jul 2018 16:31:45 +0000 (13:31 -0300)]
ARM: dts: imx51: Add tigerp support
As per the i.MX51 Reference Manual add an entry for the
'tigerp' region in the device tree.
This is needed for accessing the ARM_GPC register to set the
DBGEN bit, so that the debug clocks can be turned on.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 10 Jul 2018 16:31:44 +0000 (13:31 -0300)]
ARM: dts: imx51: Add PMU support
Add PMU support in the device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 10 Jul 2018 16:31:43 +0000 (13:31 -0300)]
dt-bindings: freescale: Add bindings for the tigerp module
Add bindings for the tigerp module present on i.MX51.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Mon, 9 Jul 2018 18:19:14 +0000 (15:19 -0300)]
ARM: dts: imx51: Add M4IF support
As per the i.MX51 Reference Manual the M4IF register region
starts at 0x83fd8000 and has a 4kB address range.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Sergey Lapin <sergey.lapin@cogentembedded.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Mon, 9 Jul 2018 18:19:13 +0000 (15:19 -0300)]
dt-bindings: freescale: Add bindings for the M4IF module
Add bindings for the M4IF module present on i.MX51.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Wed, 11 Jul 2018 05:07:04 +0000 (22:07 -0700)]
ARM: dts: imx: Add ZII SCU3 ESB
Add support for the Zodiac Inflight Innovations i.MX51-base SCU3 Ethernet
Switch Board (ESB)
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Leonard Crestez [Wed, 11 Jul 2018 12:11:17 +0000 (15:11 +0300)]
ARM: dts: imx6sl: Convert gpc to new bindings
With old bindings imx_gpc_onecell_data always sets num_domains to 2 so
the DISPMIX domain can't actually be referenced. The pd is still defined
and pm core shuts it down as "unused" so display can't work.
Fix this by converting to new gpc bindings by adding pgc nodes and
referencing the newly-defined &pu_disp domain from &lcdif.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Wed, 11 Jul 2018 00:58:59 +0000 (08:58 +0800)]
ARM: dts: imx6sx: add ocram_s support
i.MX6SX has a 16KB always-on ocram bank called
ocram_s, enable it as another mmio sram.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Mon, 9 Jul 2018 15:48:48 +0000 (17:48 +0200)]
ARM: dts: imx6qdl-apalis/-colibri: remove unused pinctrl groups
100/200MHz states for USDHC3 are not required since the SoC
does not support modes faster than DDR52 for the on board eMMC.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Mon, 9 Jul 2018 15:48:47 +0000 (17:48 +0200)]
ARM: dts: imx6qdl-apalis/-colibri: assign VDDD to SGTL5000
VDDD is connected to VGEN4 of the PF0100. This rail should only
run at 1.8V since there are multiple consumer and they all
expect the rail to be at 1.8V.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Mon, 9 Jul 2018 15:48:46 +0000 (17:48 +0200)]
ARM: dts: imx6qdl-apalis/-colibri: fix on-module regulators
Remove the 2.5V regulator, it does not exist. There is 3.3V and
3.3V_AUDIO provided to the module through the edge connector,
model those as fixed regulators like we use to do in other
Colibri device trees. The SGTL5000 uses 3.3V_AUDIO as VDDA. Note
that the driver derives the analog ground voltage (VAG) from this
supply. The new value should allow higher output swings before
clipping occurs. Refer to the SGTL5000 datasheet for details.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Mon, 9 Jul 2018 15:48:45 +0000 (17:48 +0200)]
ARM: dts: imx6qdl-apalis/-colibri: remove 1.8V regulator
The fixed 1.8V regulator is not used, and there is in fact no
fixed 1.8V regulator on the module. Remove it.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Mon, 9 Jul 2018 15:48:44 +0000 (17:48 +0200)]
ARM: dts: imx6qdl-apalis/-colibri: disable read-only switch
Use the disable-wp to indicate that Apalis and Colibri iMX6 do not
make use of the native write-protect signal available on the i.MX 6
SoCs. This prevents warnings:
mmc0: host does not support reading read-only switch, assuming write-enable
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Mon, 9 Jul 2018 15:48:43 +0000 (17:48 +0200)]
ARM: dts: imx6qdl-apalis/-colibri: prevent 1.8V modes
Use no-1-8-v device tree property to indicate that the board does
not support 1.8V signaling. The property voltage-ranges seems not
appropriate in our case since we do not have level shifters in
place.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Mon, 9 Jul 2018 15:48:42 +0000 (17:48 +0200)]
ARM: dts: imx6q-apalis-eval: add carrier board 3.3V supply
Add the 3.3V main supply on the carrier board. Currently as a fixed
supply since not all consumer are modeled yet. This gets also rid of
some missing supply warnings.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Mon, 9 Jul 2018 15:48:41 +0000 (17:48 +0200)]
ARM: dts: imx6q-apalis: add chosen node
Add Apalis UART1 as default serial console.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Sat, 7 Jul 2018 02:49:02 +0000 (19:49 -0700)]
ARM: dts: imx: Add ZII SCU2 Mezz board
Add support for the Zodiac Inflight Innovations SCU2 Mezz
board (i.MX51-based).
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 4 Jul 2018 17:52:50 +0000 (14:52 -0300)]
ARM: dts: imx: Remove optional 'fsl,sec-era' property
Since commit
654f2b937b38 ("crypto: caam - allow retrieving 'era' from
register") the CAAM driver is capable of obtaining the era version by
reading the appropriate CAAM registers, so let the CAAM driver discover
the era version in run-time instead of hardcoding such information in the
device tree.
According to Documentation/devicetree/bindings/crypto/fsl-sec4.txt the
'fsl,sec-era' is an optional property and this can be safely removed
now.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Vladimir Zapolskiy [Tue, 3 Jul 2018 19:29:34 +0000 (22:29 +0300)]
ARM: dts: imx31: add LogicPD MX31Lite board description
The added DTS contains a combined description of LogicPD MX31 Lite
SoM devices, peripherals are routed to ports on a baseboard:
* PATA controller,
* SD/MMC controller,
* 2 GPIO LEDs,
* UART controllers,
* Freescale MC13783 MFD connected over SPI,
* SMSC LAN9117,
* ST Micro NAND SLC, 64 MiB,
* Intel NOR flash, 16 MiB.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Vladimir Zapolskiy [Thu, 5 Jul 2018 19:05:49 +0000 (22:05 +0300)]
ARM: dts: imx31: add device tree description of basic controllers
The change adds a number of basic peripherals found on i.MX31 SoC:
* GPIO controllers,
* I2C master controllers,
* SPI master controllers,
* ATA controller,
* SDHC controllers,
* RTC, watchdog and PWM contollers,
* SDMA,
* IRAM,
* NAND and WEIM controllers on EMI.
The added controller devices were tested on Freescale i.MX31 powered
LogicPD Lite SoM and baseboard.
DMA functionality was tested on SDHC and SPI controllers so far,
thus dmas properties are added to those device nodes only.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 3 Jul 2018 13:05:54 +0000 (10:05 -0300)]
ARM: dts: imx51: Fix USB PHY duplicate unit-address
Currently the following DTC warnings are seen with W=1:
arch/arm/boot/dts/imx51-babbage.dtb: Warning (unique_unit_address): /usbphy/usbphy@0: duplicate unit-address (also used in node /usbphy/usbh1phy@0)
arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dtb: Warning (unique_unit_address): /usbphy/usbphy@0: duplicate unit-address (also used in node /usbphy/usbh1phy@0)
Fix it by moving the USB PHY nodes outside of simple-bus and drop the
unneeded unit-address, which matches the bindings documentation
at Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
While at it rename the USB PHY node to usbphy1 for consistency.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Viresh Kumar [Fri, 25 May 2018 10:32:01 +0000 (16:02 +0530)]
ARM: dts: imx: Add missing OPP properties for CPUs
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing properties (like clocks, supply, clock latency) as
well to make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Mon, 2 Jul 2018 02:04:36 +0000 (10:04 +0800)]
ARM: dts: imx6: correct anatop regulators range
According to i.MX6 datasheet, the LDO_1P1's typical
programming operating range is 1.0V to 1.2V, and
the LDO_2P5's typical programming operating range
is 2.25V to 2.75V, correct LDO_1P1 and LDO_2P5's
regulator range settings for i.MX6 SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Sun, 1 Jul 2018 22:56:01 +0000 (19:56 -0300)]
ARM: dts: imx6sll: Fix the SPDX notation for header file
Per Documentation/process/license-rules.rst the SPDX notation for
header file should be /* */ style, so fix it accordingly.
Fixes:
9f30b6b1a957 ("ARM: dts: imx: Add basic dtsi file for imx6sll")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Sébastien Szymanski [Fri, 29 Jun 2018 14:52:21 +0000 (16:52 +0200)]
ARM: dts: imx6ull: add operating points
i.MX6ULL has different operating ranges than i.MX6UL so add the
operating points for the i.MX6ULL and remove them from board device
trees. A 25mV offset is added to the minimum allowed values like for the
i.MX6UL.
The valid frequencies are now selected by the cpufreq driver according
to ratings stored in fuses since commit
0aa9abd4c212 ("cpufreq: imx6q:
check speed grades for i.MX6ULL")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Nick Dyer [Thu, 28 Jun 2018 22:56:26 +0000 (23:56 +0100)]
ARM: dts: imx51-zii-rdu1: correct touchscreen axis inversion
The RMI4 touchscreen driver applied inversion and axis swap in the
wrong order, violating the DT binding for those properties. This was fixed in
645a397, so correct the RDU1 DT to apply the inversion to the
correct axis.
Tested on Zii RDU1 00-5105-30 rev B
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Sebastian Reichel [Thu, 28 Jun 2018 16:36:39 +0000 (18:36 +0200)]
ARM: dts: imx53-ppd: Rename usbphy nodes
This renames usbphy nodes 2 & 3, so that they follow the same
format as usbphy node 0 & 1 from imx53.dtsi.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Sebastian Reichel [Thu, 28 Jun 2018 16:36:38 +0000 (18:36 +0200)]
ARM: dts: imx53-ppd: Add fixed-regulator information
Add information about 3V3 power rail to avoid kernel warnings,
that dummy regulators have been added.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Tue, 3 Jul 2018 05:43:47 +0000 (13:43 +0800)]
ARM: dts: imx51-babbage: Make use of pinctrl_usbh1reg
Pinctrl_usbh1reg defines pinmux setting for reset GPIO used by
usbh1phy, but is not referenced by that node. Fix that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Viresh Kumar [Fri, 25 May 2018 10:31:48 +0000 (16:01 +0530)]
ARM: dts: ls1021a: Add missing cooling device properties for CPUs
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Thu, 28 Jun 2018 01:04:27 +0000 (09:04 +0800)]
ARM: dts: imx6sll-evk: enable usdhc3 slot
On i.MX6SLL EVK board, SD3 slot can be used for
WiFi and other SD accessories, enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Thu, 28 Jun 2018 04:24:24 +0000 (21:24 -0700)]
ARM: dts: imx6qdl-zii-rdu2: Populate RAVE SP power button node
RAVE SP found on RDU2 implements power button control compatible with
the rave-sp-pwrbutton driver. Add a node to make it availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Thu, 28 Jun 2018 04:24:23 +0000 (21:24 -0700)]
ARM: dts: imx6qdl-zii-rdu2: Populate RAVE SP backlight node
RAVE SP found on RDU2 implements backlight control compatible with the
rave-sp-backlight driver. Add a node to make it availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Thu, 28 Jun 2018 04:24:22 +0000 (21:24 -0700)]
ARM: dts: imx6qdl-zii-rdu2: Populate RAVE SP EEPROM nodes
ZII's RDU2s come with two EEPROMs attached to RAVE SP. Add
corresponding nodes to make them availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Thu, 28 Jun 2018 04:24:21 +0000 (21:24 -0700)]
ARM: dts: imx51-zii-rdu1: Populate RAVE SP EEPROM nodes
ZII's RDU1s come with up to 3 EEPROMs attached to RAVE SP. Add
corresponding nodes to make them availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 27 Jun 2018 00:34:22 +0000 (21:34 -0300)]
ARM: dts: imx53-qsb: Let the codec control MCLK pinctrl
The hog pinctrl hog is meant for pins that do not have an
associated driver.
The MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK pin is the one that
provides the MCLK signal to the SGTL5000 codec, so a
better represenation is to move it under the codec node.
While at it, change the pinctrl value from 0x80000000 to the
POR reset value of register IOMUXC_SW_PAD_CTL_PAD_GPIO_0.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 27 Jun 2018 00:05:01 +0000 (21:05 -0300)]
ARM: dts: imx6ull: Switch to SPDX identifier
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 26 Jun 2018 23:18:52 +0000 (20:18 -0300)]
ARM: dts: imx51: Add sahara crypto support
The sahara crypto block on i.MX51 has the same IP version as
the one on i.MX53.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Tue, 26 Jun 2018 14:52:43 +0000 (16:52 +0200)]
ARM: dts: imx6qdl-colibri: use pull-down on wake-up pin
The wake-up pin is pulled low with 100kOhm on the carrier board.
The current configuration of 100kOhm pull-up caused lots of
interrupts, especially during boot up. Make sure the pin is at a
reasonable level at startup by pulling it low on SoC side too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Tue, 26 Jun 2018 14:52:42 +0000 (16:52 +0200)]
ARM: dts: imx6qdl-colibri: move card detect to module device tree
Muxing the card detect only in the carrier board device tree
overwrites the USDHC muxing in the module level device tree.
Move card detect to the module level device tree since this
is also a default pinout of the Colibri standard. If a carrier
board requires a different setting it still can overwrite the
nodes in the carrier board specific device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Tue, 26 Jun 2018 14:52:41 +0000 (16:52 +0200)]
ARM: dts: imx6qdl-colibri: mux SD/MMC card detect explicitly
Do not rely on reset/boot defaults and use a default GPIO setting
with pull-up enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Leonard Crestez [Mon, 25 Jun 2018 20:09:32 +0000 (23:09 +0300)]
ARM: dts: imx: Add missing chosen/stdout-path
This makes it possible to enable earlycon for debugging by just passing
an empty "earlycon" argument on the kernel command-line.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Kurz [Sun, 24 Jun 2018 06:15:38 +0000 (06:15 +0000)]
ARM: dts: imx50: remove non-existent USB instances
According to the i.MX50 Reference Manual, the SoC features one USB OTG
and one host controller. Remove the non-existent instances from the
DTS which probably got initially copied from the mx53 DTS.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Kurz [Sun, 24 Jun 2018 05:59:29 +0000 (05:59 +0000)]
ARM: dts: imx50: fix KPP pin definition typos
iMX50 pin mux options for pads KEY_COL2 and KEY_COL3 allow muxing the same
KEY_COL instances as the pad name. Fix typos shifting KEY_COL instances.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 20 Jun 2018 18:06:19 +0000 (15:06 -0300)]
ARM: dts: imx51: Add aipstz nodes
Currently when trying to use the 'devmem' tool to read/write
registers the following bus error is observed:
[ 82.689185] Unhandled fault: external abort on non-linefetch (0x1018) at 0xb6ff10c4
[ 82.697071] pgd = (ptrval)
[ 82.699920] [
b6ff10c4] *pgd=
a87c5831, *pte=
73fa8383, *ppte=
73fa8a33
Bus error
Add the aipstz nodes, so that the following function from
imx51_dt_init() can work properly:
imx_aips_allow_unprivileged_access("fsl,imx51-aipstz");
After adding these nodes, 'devmem' tool can work correctly,
which is very useful for debugging purposes.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Leonard Crestez [Wed, 20 Jun 2018 10:41:16 +0000 (13:41 +0300)]
ARM: dts: imx7d-sdb: Restore pwm backlight support
This was removed in commit
5eaeaccdaedb ("ARM: dts: imx7d-sdb: Pass
'enable-gpios' and 'power-supply' properties") with a note claiming that
GPIO1_IO01 is connected to a pin labeled as "PWREN" on the connector.
Despite that label this pin does actually work as a PWM controlling
brightness. So restore pwm functionality.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Wed, 20 Jun 2018 08:38:37 +0000 (16:38 +0800)]
ARM: dts: imx6sll: declare src module to be compatible to imx51's src
i.MX6SLL uses same SRC module as i.MX51, add "fsl,imx51-src"
compatible string to enable SRC driver to support setting
CPU resume address for cpu-idle and suspend/resume.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Emmanuel Vadot [Mon, 18 Jun 2018 15:42:57 +0000 (17:42 +0200)]
ARM: dts: imx6: RIoTboard Add chosen stdout-path property
The RIoTboard debug uart is connected to serial1.
Add a chosen property in the DTS so OS knows what serial port to use for
the console.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Fri, 8 Jun 2018 09:06:40 +0000 (11:06 +0200)]
ARM: dts: imx: add cooling-cells for cpufreq cooling device
Add #cooling-cells for i.MX6/7 SoCs for cpufreq cooling device usage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Philipp Zabel [Wed, 13 Dec 2017 14:24:06 +0000 (15:24 +0100)]
ARM: dts: imx51: add CodaHx4 VPU
Add the CodaHx4 VPU to the i.MX51 device tree.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Leonard Crestez [Mon, 18 Jun 2018 13:11:09 +0000 (16:11 +0300)]
ARM: dts: imx7d-sdb: Remove duplicate regulator-can2-3v3
Two different regulators are defined with the same name and label but
distinct properties.
The first definition was added with the first board dts and the second
was added when upstream added flexcan support.
Looking at schematics it is indeed gpio2 14 connected to the STB pin of
the CAN transceiver so remove the first definition.
The second definition entirely overrides the first so this already
worked and this patch results in no DTB change, just a cleanup.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Leonard Crestez [Mon, 18 Jun 2018 08:15:44 +0000 (11:15 +0300)]
ARM: dts: imx6qdl-sabreauto: Add sensors
The following sensors are on I2C3 on the baseboard:
* isil,isl29023 light sensor
* fsl,mag3110 magnetometer
* fsl,mma8451 accelerometer
Added under i2cmux/i2c@1 because they're not otherwise accessible.
These are all supported by iio with following configs:
* CONFIG_SENSORS_ISL29018
* CONFIG_MAG3110
* CONFIG_MMA8452
Tested with raw reads from iio sysfs.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jagan Teki [Thu, 7 Jun 2018 13:51:33 +0000 (19:21 +0530)]
ARM: dts: imx6qdl-icore: Fix wrong reg_2p5 regulator node name
- in reg_2p5, fix regulator node name as regulator-2p5v
- remove exctra line
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jagan Teki [Thu, 7 Jun 2018 13:51:32 +0000 (19:21 +0530)]
ARM: dts: imx6q-icore-mipi: Add OV5640 Camera sensor
OV5640 Camera sensor is connected in i.CoreM6 1.5 Quad/Dual MIPI
starter kit.
This patch also move MX6QDL_PAD_GPIO_0__CCM_CLKO1 pinctrl
from i2c3 to ov5640 pinctrl.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jagan Teki [Thu, 7 Jun 2018 13:51:31 +0000 (19:21 +0530)]
ARM: dts: imx6dl: Add Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit support
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.
notable features:
CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory Up to 2 GB DDR3-1066
Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4
port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lucas Stach [Wed, 6 Jun 2018 09:30:45 +0000 (11:30 +0200)]
ARM: dts: imx6: RDU2: correct touchscreen axis inversion
The RMI4 touchscreen driver applied inversion and axis swap in the
wrong order, violating the DT binding for those properties. This is
fixed now, so correct the RDU2 DT to apply the inversion to the
correct axis.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Kurz [Tue, 29 May 2018 06:20:21 +0000 (06:20 +0000)]
ARM: dts: imx6dl-riotboard: fix OTG regulator polarity
USB OTG power is switched on when the GPIO is pulled low.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Kurz [Tue, 29 May 2018 06:20:20 +0000 (06:20 +0000)]
ARM: dts: imx6qdl-wandboard: enable USB OTG
Enable USB OTG (dual-role) on the Wandboard.
Note, that the USB_OTG_VBUS current is quite limited due to a 22R resistor
in the power line. Hence, the overcurrent signal of 1A will never be
triggered on this board.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Kurz [Tue, 29 May 2018 06:20:19 +0000 (06:20 +0000)]
ARM: dts: imx6dl-riotboard: remove regulators bus node
To match the convention, move regulator-fixed nodes directly into
the root node.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Kurz [Tue, 29 May 2018 06:20:18 +0000 (06:20 +0000)]
ARM: dts: imx6qdl-wandboard: remove regulators bus node
To match the convention, move all regulator-fixed nodes directly into
the root node.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Sat, 26 May 2018 02:12:38 +0000 (19:12 -0700)]
ARM: dts: imx51-zii-rdu1: Make sure SD1_WP is low
Make sure that MX51_PAD_GPIO1_1 does not remain configure as
ALT0/SD1_WP (it is out of reset). This is needed because of external
pull-up resistor attached to that pad that, when left unchanged, will
drive SD1_WP high preventing eSDHC1/eMMC from working correctly.
To fix that add a pinmux configuration line configureing the pad to
function as a GPIO. While we are at it, add a corresponding
output-high GPIO hog in an effort to minimize current consumption.
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-By: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Nikita Yushchenko [Thu, 17 May 2018 19:19:23 +0000 (22:19 +0300)]
ARM: dts: imx51-zii-rdu1: add rave-sp subdevices
This adds rave-sp powerbutton and backlight devices to RDU1 device tree.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lukasz Majewski [Tue, 12 Jun 2018 13:32:08 +0000 (15:32 +0200)]
ARM: dts: imx53: Add support for imx53 HSC/DDC boards from K+P
This commit provides support for HSC and DDC boards from
Kieback&Peter GmbH vendor.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Daniel Mack [Wed, 23 May 2018 08:30:12 +0000 (10:30 +0200)]
ARM: dts: imx6: make edt-ft5x06 a wakeup source for imx6 boards
The touchscreen driver no longer configures the device as wakeup source by
default. A "wakeup-source" property is needed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bai Ping [Fri, 25 May 2018 07:42:07 +0000 (15:42 +0800)]
ARM: dts: imx: Add basic dts support for imx6sll EVK board
Add dts file support for imx6sll EVK board.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bai Ping [Fri, 25 May 2018 07:42:06 +0000 (15:42 +0800)]
ARM: dts: imx: Add basic dtsi file for imx6sll
Add dtsi file for imx6sll.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Linus Torvalds [Sat, 16 Jun 2018 23:04:49 +0000 (08:04 +0900)]
Linux 4.18-rc1
Linus Torvalds [Sat, 16 Jun 2018 20:37:55 +0000 (05:37 +0900)]
Merge tag 'for-linus-
20180616' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes that should go into -rc1. This contains:
- bsg_open vs bsg_unregister race fix (Anatoliy)
- NVMe pull request from Christoph, with fixes for regressions in
this window, FC connect/reconnect path code unification, and a
trace point addition.
- timeout fix (Christoph)
- remove a few unused functions (Christoph)
- blk-mq tag_set reinit fix (Roman)"
* tag 'for-linus-
20180616' of git://git.kernel.dk/linux-block:
bsg: fix race of bsg_open and bsg_unregister
block: remov blk_queue_invalidate_tags
nvme-fabrics: fix and refine state checks in __nvmf_check_ready
nvme-fabrics: handle the admin-only case properly in nvmf_check_ready
nvme-fabrics: refactor queue ready check
blk-mq: remove blk_mq_tagset_iter
nvme: remove nvme_reinit_tagset
nvme-fc: fix nulling of queue data on reconnect
nvme-fc: remove reinit_request routine
blk-mq: don't time out requests again that are in the timeout handler
nvme-fc: change controllers first connect to use reconnect path
nvme: don't rely on the changed namespace list log
nvmet: free smart-log buffer after use
nvme-rdma: fix error flow during mapping request data
nvme: add bio remapping tracepoint
nvme: fix NULL pointer dereference in nvme_init_subsystem
blk-mq: reinit q->tag_set_list entry only after grace period
Linus Torvalds [Sat, 16 Jun 2018 20:25:18 +0000 (05:25 +0900)]
Merge tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental
Pull documentation fixes from Mauro Carvalho Chehab:
"This solves a series of broken links for files under Documentation,
and improves a script meant to detect such broken links (see
scripts/documentation-file-ref-check).
The changes on this series are:
- can.rst: fix a footnote reference;
- crypto_engine.rst: Fix two parsing warnings;
- Fix a lot of broken references to Documentation/*;
- improve the scripts/documentation-file-ref-check script, in order
to help detecting/fixing broken references, preventing
false-positives.
After this patch series, only 33 broken references to doc files are
detected by scripts/documentation-file-ref-check"
* tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental: (26 commits)
fix a series of Documentation/ broken file name references
Documentation: rstFlatTable.py: fix a broken reference
ABI: sysfs-devices-system-cpu: remove a broken reference
devicetree: fix a series of wrong file references
devicetree: fix name of pinctrl-bindings.txt
devicetree: fix some bindings file names
MAINTAINERS: fix location of DT npcm files
MAINTAINERS: fix location of some display DT bindings
kernel-parameters.txt: fix pointers to sound parameters
bindings: nvmem/zii: Fix location of nvmem.txt
docs: Fix more broken references
scripts/documentation-file-ref-check: check tools/*/Documentation
scripts/documentation-file-ref-check: get rid of false-positives
scripts/documentation-file-ref-check: hint: dash or underline
scripts/documentation-file-ref-check: add a fix logic for DT
scripts/documentation-file-ref-check: accept more wildcards at filenames
scripts/documentation-file-ref-check: fix help message
media: max2175: fix location of driver's companion documentation
media: v4l: fix broken video4linux docs locations
media: dvb: point to the location of the old README.dvb-usb file
...
Linus Torvalds [Sat, 16 Jun 2018 20:06:18 +0000 (05:06 +0900)]
Merge tag 'fsnotify_for_v4.18-rc1' of git://git./linux/kernel/git/jack/linux-fs
Pull fsnotify updates from Jan Kara:
"fsnotify cleanups unifying handling of different watch types.
This is the shortened fsnotify series from Amir with the last five
patches pulled out. Amir has modified those patches to not change
struct inode but obviously it's too late for those to go into this
merge window"
* tag 'fsnotify_for_v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fsnotify: add fsnotify_add_inode_mark() wrappers
fanotify: generalize fanotify_should_send_event()
fsnotify: generalize send_to_group()
fsnotify: generalize iteration of marks by object type
fsnotify: introduce marks iteration helpers
fsnotify: remove redundant arguments to handle_event()
fsnotify: use type id to identify connector object type
Linus Torvalds [Sat, 16 Jun 2018 20:00:24 +0000 (05:00 +0900)]
Merge tag 'fbdev-v4.18' of git://github.com/bzolnier/linux
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"There is nothing really major here, few small fixes, some cleanups and
dead drivers removal:
- mark omapfb drivers as orphans in MAINTAINERS file (Tomi Valkeinen)
- add missing module license tags to omap/omapfb driver (Arnd
Bergmann)
- add missing GPIOLIB dependendy to omap2/omapfb driver (Arnd
Bergmann)
- convert savagefb, aty128fb & radeonfb drivers to use msleep & co.
(Jia-Ju Bai)
- allow COMPILE_TEST build for viafb driver (media part was reviewed
by media subsystem Maintainer)
- remove unused MERAM support from sh_mobile_lcdcfb and shmob-drm
drivers (drm parts were acked by shmob-drm driver Maintainer)
- remove unused auo_k190xfb drivers
- misc cleanups (Souptick Joarder, Wolfram Sang, Markus Elfring, Andy
Shevchenko, Colin Ian King)"
* tag 'fbdev-v4.18' of git://github.com/bzolnier/linux: (26 commits)
fb_omap2: add gpiolib dependency
video/omap: add module license tags
MAINTAINERS: make omapfb orphan
video: fbdev: pxafb: match_string() conversion fixup
video: fbdev: nvidia: fix spelling mistake: "scaleing" -> "scaling"
video: fbdev: fix spelling mistake: "frambuffer" -> "framebuffer"
video: fbdev: pxafb: Convert to use match_string() helper
video: fbdev: via: allow COMPILE_TEST build
video: fbdev: remove unused sh_mobile_meram driver
drm: shmobile: remove unused MERAM support
video: fbdev: sh_mobile_lcdcfb: remove unused MERAM support
video: fbdev: remove unused auo_k190xfb drivers
video: omap: Improve a size determination in omapfb_do_probe()
video: sm501fb: Improve a size determination in sm501fb_probe()
video: fbdev-MMP: Improve a size determination in path_init()
video: fbdev-MMP: Delete an error message for a failed memory allocation in two functions
video: auo_k190x: Delete an error message for a failed memory allocation in auok190x_common_probe()
video: sh_mobile_lcdcfb: Delete an error message for a failed memory allocation in two functions
video: sh_mobile_meram: Delete an error message for a failed memory allocation in sh_mobile_meram_probe()
video: fbdev: sh_mobile_meram: Drop SUPERH platform dependency
...
Linus Torvalds [Sat, 16 Jun 2018 07:32:04 +0000 (16:32 +0900)]
Merge branch 'afs-proc' of git://git./linux/kernel/git/viro/vfs
Pull AFS updates from Al Viro:
"Assorted AFS stuff - ended up in vfs.git since most of that consists
of David's AFS-related followups to Christoph's procfs series"
* 'afs-proc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
afs: Optimise callback breaking by not repeating volume lookup
afs: Display manually added cells in dynamic root mount
afs: Enable IPv6 DNS lookups
afs: Show all of a server's addresses in /proc/fs/afs/servers
afs: Handle CONFIG_PROC_FS=n
proc: Make inline name size calculation automatic
afs: Implement network namespacing
afs: Mark afs_net::ws_cell as __rcu and set using rcu functions
afs: Fix a Sparse warning in xdr_decode_AFSFetchStatus()
proc: Add a way to make network proc files writable
afs: Rearrange fs/afs/proc.c to remove remaining predeclarations.
afs: Rearrange fs/afs/proc.c to move the show routines up
afs: Rearrange fs/afs/proc.c by moving fops and open functions down
afs: Move /proc management functions to the end of the file
Linus Torvalds [Sat, 16 Jun 2018 07:21:50 +0000 (16:21 +0900)]
Merge branch 'work.compat' of git://git./linux/kernel/git/viro/vfs
Pull compat updates from Al Viro:
"Some biarch patches - getting rid of assorted (mis)uses of
compat_alloc_user_space().
Not much in that area this cycle..."
* 'work.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
orangefs: simplify compat ioctl handling
signalfd: lift sigmask copyin and size checks to callers of do_signalfd4()
vmsplice(): lift importing iovec into vmsplice(2) and compat counterpart