OSDN Git Service
himanshu.madhani@cavium.com [Mon, 4 Dec 2017 22:45:17 +0000 (14:45 -0800)]
scsi: qla2xxx: Update driver version to 10.00.00.03-k
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
himanshu.madhani@cavium.com [Mon, 4 Dec 2017 22:45:16 +0000 (14:45 -0800)]
scsi: qla2xxx: Fix memory leak in dual/target mode
When driver is loaded in Target/Dual mode, it creates QPair to support
MQ and allocates resources for each QPair. This Qpair initialization is
delayed until the FW personality is changed to Dual/Target mode by
issuing chip reset. At the time of chip reset firmware is re-initilized
in correct personality all the QPairs are initialized by sending
MBC_INITIALIZE_MULTIQ (001Fh).
This patch fixes memory leak by adding check to issue
MBC_INITIALIZE_MULTIQ command only while deleting rsp/req queue when the
flag is set for initiator mode, and clean up QPair resources correctly
during the driver unload. This MBX does not need to be issued for
Target/Dual mode because chip reset will reset ISP.
Fixes:
d65237c7f0860 ("scsi: qla2xxx: Fix mailbox failure while deleting Queue pairs")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:45:15 +0000 (14:45 -0800)]
scsi: qla2xxx: Fix system crash in qlt_plogi_ack_unref
Fix system crash due to NULL pointer access.
qlt_plogi_ack_t and fc_port structures were not properly bound before
calling qlt_plogi_ack_unref().
RIP: 0010:qlt_plogi_ack_unref+0xa1/0x150 [qla2xxx]
Call Trace:
qla24xx_create_new_sess+0xb1/0x320 [qla2xxx]
qla2x00_do_work+0x123/0x260 [qla2xxx]
qla2x00_iocb_work_fn+0x30/0x40 [qla2xxx]
process_one_work+0x1f3/0x530
worker_thread+0x4e/0x480
kthread+0x10c/0x140
Fixes:
726b85487067d ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Giridhar Malavali [Mon, 4 Dec 2017 22:45:14 +0000 (14:45 -0800)]
scsi: qla2xxx: Remove aborting ELS IOCB call issued as part of timeout.
This fix the spinlock recursion issue seen while unloading the driver.
14 [
ffff9f2e21e03db8] native_queued_spin_lock_slowpath at
ffffffffad0d8802
15 [
ffff9f2e21e03dc0] do_raw_spin_lock at
ffffffffad0d99e4
16 [
ffff9f2e21e03dd8] _raw_spin_lock_irqsave at
ffffffffad652471
17 [
ffff9f2e21e03e00] qla2x00_els_dcmd_iocb_timeout at
ffffffffc070cd63
18 [
ffff9f2e21e03e40] qla2x00_sp_timeout at
ffffffffc06f06d3 [qla2xxx]
19 [
ffff9f2e21e03e68] call_timer_fn at
ffffffffad0f97d8
20 [
ffff9f2e21e03ed8] run_timer_softirq at
ffffffffad0faf47
21 [
ffff9f2e21e03f68] __softirqentry_text_start at
ffffffffad655f32
Fixes:
6eb54715b54bb ("qla2xxx: Added interface to send explicit LOGO.")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Giridhar Malavali [Mon, 4 Dec 2017 22:45:13 +0000 (14:45 -0800)]
scsi: qla2xxx: Defer processing of GS IOCB calls
This patch defers processing of GS IOCB calls from interrupt context to
avoid hardware spinlock recursion.
Following stack trace is seen
? mod_timer+0x193/0x330
? ql_dbg+0xa7/0xf0 [qla2xxx]
_raw_spin_lock_irqsave+0x31/0x40
qla2x00_start_sp+0x3b/0x250 [qla2xxx]
qla24xx_async_gnl+0x1d3/0x240 [qla2xxx]
qla24xx_fcport_handle_login+0x285/0x290 [qla2xxx]
? vprintk_func+0x20/0x50
Fixes:
726b85487067d ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:45:12 +0000 (14:45 -0800)]
scsi: qla2xxx: Clear loop id after delete
Clear loop id after delete to prevent session invalidation of stale
session.
Fixes:
726b85487067d ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:45:11 +0000 (14:45 -0800)]
scsi: qla2xxx: Fix scan state field for fcport
Add correct value of scan_state field indicating state of the FC port
Fixes:
726b85487067d ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:45:10 +0000 (14:45 -0800)]
scsi: qla2xxx: Replace fcport alloc with qla2x00_alloc_fcport
Current code manually allocate an fcport structure that is not properly
initialize. Replace kzalloc with qla2x00_alloc_fcport, so that all
fields are initialized. Also set set scan flag to port found
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:45:09 +0000 (14:45 -0800)]
scsi: qla2xxx: Fix abort command deadlock due to spinlock
Original code acquires hardware_lock to add Abort IOCB onto driver
request queue for processing. However, abort_command() will also acquire
hardware lock to look up sp pointer before issuing abort IOCB command
resulting into a deadlock. This patch safely removes the possible
deadlock scenario by removing extra spinlock.
Fixes:
6eb54715b54bb ("qla2xxx: Added interface to send explicit LOGO.")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:45:08 +0000 (14:45 -0800)]
scsi: qla2xxx: Fix PRLI state check
Get Port Database MBX cmd is to validate current Login state upon PRLI
completion. Current code looks at the last login state for re-validation
which was incorrect. This patch removed incorrect state check.
Fixes:
15f30a5752287 ("qla2xxx: Use IOCB interface to submit non-critical MBX.")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:45:06 +0000 (14:45 -0800)]
scsi: qla2xxx: Fix Relogin being triggered too fast
Current driver design schedules relogin process via DPC thread every 1
second. In a large fabric, this DPC thread tries to schedule too many
jobs and might get overloaded. As a result of this processing of DPC
thread, it can schedule relogin earlier than 1 second.
Fixes:
726b85487067d ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:45:05 +0000 (14:45 -0800)]
scsi: qla2xxx: Relogin to target port on a cable swap
If user swaps one target port for another target port for same switch
port, the new target port is not being recognized by the driver. Current
code assumes that old Target port has recovered from link down. The fix
will ask switch what is the WWPN of a specific NportID (GPNID) rather
than assuming it's the same Target port which has came back.
Fixes:
726b85487067d ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sawan Chandak [Mon, 4 Dec 2017 22:45:04 +0000 (14:45 -0800)]
scsi: qla2xxx: Fix NPIV host cleanup in target mode
Add check to make sure we are cleaning up global target host list only
for NPIV hosts
Fixes:
bdbe24de281e2 ("scsi: qla2xxx: Cleanup NPIV host in target mode during config teardown")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:45:03 +0000 (14:45 -0800)]
scsi: qla2xxx: Fix login state machine stuck at GPDB
This patch returns discovery state machine back to Login Complete.
Fixes:
726b85487067d ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:45:02 +0000 (14:45 -0800)]
scsi: qla2xxx: Serialize GPNID for multiple RSCN
GPNID is triggered by RSCN. For multiple RSCNs of the same affected
NPORT ID, serialize the GPNID to prevent confusion.
Fixes:
726b85487067d ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:45:01 +0000 (14:45 -0800)]
scsi: qla2xxx: Retry switch command on time out
Retry GID_PN & GPN_ID switch commands for time out case.
Fixes:
726b85487067d ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:45:00 +0000 (14:45 -0800)]
scsi: qla2xxx: Fix re-login for Nport Handle in use
When NPort Handle is in use, driver needs to mark the handle as used and
pick another. Instead, the code clears the handle and re-pick the same
handle.
Fixes:
726b85487067d ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:44:59 +0000 (14:44 -0800)]
scsi: qla2xxx: Skip IRQ affinity for Target QPairs
Fix co-existence between Block MQ and Target Mode. Block MQ and
initiator mode requires midlayer queue mapping to check for IRQ to be
affinitized. For target mode, it's not the case.
Fixes:
09620eeb62c41 ("scsi: qla2xxx: Add debug knob for user control workload")
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:44:58 +0000 (14:44 -0800)]
scsi: qla2xxx: Move session delete to driver work queue
Move session delete from system work queue to driver's work queue for in
time processing.
Fixes:
726b85487067d ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:44:57 +0000 (14:44 -0800)]
scsi: qla2xxx: Fix gpnid error processing
Stop GPNID command from advancing if command has failed.
Fixes:
726b85487067d ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Mon, 4 Dec 2017 22:44:56 +0000 (14:44 -0800)]
scsi: qla2xxx: Fix system crash for Notify ack timeout handling
Fix NULL pointer crash due to missing timeout handling callback for
Notify Ack IOCB.
Fixes:
726b85487067d ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Douglas Gilbert [Tue, 5 Dec 2017 05:05:49 +0000 (00:05 -0500)]
scsi: scsi_debug: add cdb_len parameter
While testing "sd: Micro-optimize READ / WRITE CDB encoding" patches it
was helpful to check various code paths associated with READ/WRITE 6, 10
and 16 byte cdb variants. There seems to be no user space "knobs" to
twiddle use_10_for_rw and friends in the scsi_device structure. So add
a parameter to scsi_debug called "cdb_len" for this purpose.
[mkp: fixed typo]
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Mon, 4 Dec 2017 18:36:33 +0000 (10:36 -0800)]
scsi: core: Introduce scsi_devinfo_key enumeration type
Since symbolic names for the device information keys alread exist,
associate an enumeration type with these symbolic values. This change
makes it clear what the valid values for the 'key' arguments are.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Mon, 4 Dec 2017 18:36:31 +0000 (10:36 -0800)]
scsi: core: scsi_get_device_flags_keyed(): Always return device flags
Since scsi_get_device_flags_keyed() callers do not check whether or not
the returned value is an error code, change that function such that it
returns a flags value even if the 'key' argument is invalid. Note:
since commit
28a0bc4120d3 ("scsi: sd: Implement blacklist option for
WRITE SAME w/ UNMAP") bit 31 is a valid device information flag so
checking whether bit 31 is set in the return value is not sufficient to
tell the difference between an error code and a flags value.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Mon, 4 Dec 2017 18:06:24 +0000 (10:06 -0800)]
scsi: core: Convert a source code comment into a runtime check
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Mon, 4 Dec 2017 18:06:23 +0000 (10:06 -0800)]
scsi: core: Ensure that the SCSI error handler gets woken up
If scsi_eh_scmd_add() is called concurrently with
scsi_host_queue_ready() while shost->host_blocked > 0 then it can
happen that neither function wakes up the SCSI error handler. Fix
this by making every function that decreases the host_busy counter
wake up the error handler if necessary and by protecting the
host_failed checks with the SCSI host lock.
Reported-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
References: https://marc.info/?l=linux-kernel&m=
150461610630736
Fixes: commit
746650160866 ("scsi: convert host_busy to atomic_t")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Cc: Konstantin Khorenko <khorenko@virtuozzo.com>
Cc: Stuart Hayes <stuart.w.hayes@gmail.com>
Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Paul E. McKenney [Thu, 7 Dec 2017 17:40:38 +0000 (09:40 -0800)]
rcu: Export init_rcu_head() and destroy_rcu_head() to GPL modules
Use of init_rcu_head() and destroy_rcu_head() from modules results in
the following build-time error with CONFIG_DEBUG_OBJECTS_RCU_HEAD=y:
ERROR: "init_rcu_head" [drivers/scsi/scsi_mod.ko] undefined!
ERROR: "destroy_rcu_head" [drivers/scsi/scsi_mod.ko] undefined!
This commit therefore adds EXPORT_SYMBOL_GPL() for each to allow them to
be used by GPL-licensed kernel modules.
Reported-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 03:28:37 +0000 (11:28 +0800)]
scsi: arcmsr: Fix command result for CHECK_CONDITION
Fix report command result error when CHECK_CONDITION.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 02:29:44 +0000 (10:29 +0800)]
scsi: arcmsr: Update driver version to v1.40.00.04-
20171130
Update driver version to v1.40.00.04-
20171130
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 02:26:38 +0000 (10:26 +0800)]
scsi: arcmsr: Add driver module parameter msix_enable
Add module parameter msix_enable so user has the option of disabling
MSI-X interrupts if there is a platform problem.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 02:24:01 +0000 (10:24 +0800)]
scsi: arcmsr: Add driver module parameter msi_enable
Add module parameter msi_enable so user has the option of disabling MSI
interrupts if there is a platform problem.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 02:18:47 +0000 (10:18 +0800)]
scsi: arcmsr: Fix grammar
Fix grammar.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 02:16:13 +0000 (10:16 +0800)]
scsi: arcmsr: Adjust whitespace
Adjust tabs and whitespace.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 02:11:23 +0000 (10:11 +0800)]
scsi: arcmsr: Spin off duplicate code
Spin off duplicate code of timer init for message isr BH in arcmsr_probe
and arcmsr_resume as a function arcmsr_init_get_devmap_timer.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 02:02:16 +0000 (10:02 +0800)]
scsi: arcmsr: Fix clear doorbell queue on ACB_ADAPTER_TYPE_B
Fix clear doorbell queue on ACB_ADAPTER_TYPE_B controller.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 01:59:52 +0000 (09:59 +0800)]
scsi: arcmsr: Add a function to set date and time to firmware
Add a function arcmsr_set_iop_datetime and driver option set_date_time
to set date and time to firmware.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 01:57:23 +0000 (09:57 +0800)]
scsi: arcmsr: Add ACB_F_MSG_GET_CONFIG to acb->acb_flags
Add ACB_F_MSG_GET_CONFIG to acb->acb_flags for for message interrupt
checking before schedule work for get device map.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 01:55:02 +0000 (09:55 +0800)]
scsi: arcmsr: Add driver option cmd_per_lun
Add driver option cmd_per_lun to set host->cmd_per_lun value by user.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 01:51:27 +0000 (09:51 +0800)]
scsi: arcmsr: Replace constant ARCMSR_MAX_OUTSTANDING_CMD
Replace constant ARCMSR_MAX_OUTSTANDING_CMD by variable
acb->maxOutstanding that was determined by user.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 01:47:44 +0000 (09:47 +0800)]
scsi: arcmsr: Add driver option host_can_queue
Add driver option host_can_queue to set host->can_queue value by
user. It's value expands up to 1024.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 01:44:23 +0000 (09:44 +0800)]
scsi: arcmsr: replace constant ARCMSR_MAX_FREECCB_NUM
Replace constant ARCMSR_MAX_FREECCB_NUM by variable acb->maxFreeCCB that
was received from firmware.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 01:41:25 +0000 (09:41 +0800)]
scsi: arcmsr: Increase host controller command queue depth
Update ARCMSR_MAX_OUTSTANDING_CMD and ARCMSR_MAX_FREECCB_NUM to 1024.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 01:35:34 +0000 (09:35 +0800)]
scsi: arcmsr: Add code for ACB_ADAPTER_TYPE_E
Add code for ACB_ADAPTER_TYPE_E to support new adapter ARC-1884.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 01:31:59 +0000 (09:31 +0800)]
scsi: arcmsr: simplify arcmsr_iop_init function
Simplify arcmsr_iop_init function.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Tue, 5 Dec 2017 01:28:04 +0000 (09:28 +0800)]
scsi: arcmsr: Redefine ACB_ADAPTER_TYPE_A, _B, _C, _D
Redefine ACB_ADAPTER_TYPE_A, _B, _C, _D and subsequent changes.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bryant G. Ly [Mon, 4 Dec 2017 22:07:28 +0000 (16:07 -0600)]
scsi: ibmvscsis: add DRC indices to debug statements
Where applicable, changes pr_debug, pr_info, pr_err, etc. calls to the
dev_* versions. This adds the DRC index of the device to the
corresponding trace statement.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Brad Warrum <bwarrum@us.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Fri, 1 Dec 2017 13:33:27 +0000 (13:33 +0000)]
scsi: ipr: fix incorrect indentation of assignment statement
Remove one extraneous level of indentation on an assignment statement.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Fri, 1 Dec 2017 09:40:09 +0000 (09:40 +0000)]
scsi: csiostor: fix spelling mistake: "Couldnt" -> "Couldn't"
Trivial fix to spelling mistake in error message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Fri, 1 Dec 2017 09:37:25 +0000 (09:37 +0000)]
scsi: bnx2fc: fix spelling mistake: "Couldnt" -> "Couldn't"
Trivial fix to spelling mistake in error message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Michał Mirosław [Fri, 24 Nov 2017 17:02:35 +0000 (18:02 +0100)]
scsi: sd: add missing KERN_CONT for disk spin-up
KERN_CONT is now required for continued printks(). Add it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
kwmad.kim@samsung.com [Tue, 28 Nov 2017 05:35:29 +0000 (14:35 +0900)]
scsi: ufs: add some definitions included in UFS HCI specification
These would be used in the future in some specific drivers.
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Suganath Prabu S [Sat, 2 Dec 2017 10:19:26 +0000 (02:19 -0800)]
scsi: mpt3sas: Remove unused variable requeue_event
No Functional change just cleanup. Removed variable requeue_event and
made function as void.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Romain Perier [Mon, 20 Nov 2017 19:32:46 +0000 (20:32 +0100)]
scsi: mpt3sas: Replace PCI pool old API
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Vasyl Gomonovych [Tue, 21 Nov 2017 21:15:46 +0000 (22:15 +0100)]
scsi: fnic: Fix coccinelle warnings
Remove the duplicate copies of this simple function and use an
open-coded version.
drivers/scsi/fnic/fnic_debugfs.c:122:11-31: WARNING opportunity for simple_open, see also structure on line 223
Generated by: coccinelle/api/simple_open.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Li Dongyang [Mon, 13 Nov 2017 23:48:04 +0000 (10:48 +1100)]
scsi: ses: don't ask for diagnostic pages repeatedly during probe
We are testing if there is a match with the ses device in a loop by
calling ses_match_to_enclosure(), which will issue scsi receive
diagnostics commands to the ses device for every device on the same
host. On one of our boxes with 840 disks, it takes a long time to load
the driver:
[root@g1b-oss06 ~]# time modprobe ses
real 40m48.247s
user 0m0.001s
sys 0m0.196s
With the patch:
[root@g1b-oss06 ~]# time modprobe ses
real 0m17.915s
user 0m0.008s
sys 0m0.053s
Note that we still need to refresh page 10 when we see a new disk to
create the link.
Signed-off-by: Li Dongyang <dongyang.li@anu.edu.au>
Tested-by: Jason Ozolins <jason.ozolins@hpe.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Tue, 28 Nov 2017 18:12:34 +0000 (18:12 +0000)]
scsi: wd719x: make card_types static const, shrinks object size
Don't populate the read-only array card_types on the stack but instead
make it static and constify it. Makes the object code smaller by over
110 bytes:
Before:
text data bss dec hex filename
25625 5752 0 31377 7a91 drivers/scsi/wd719x.o
After:
text data bss dec hex filename
25447 5816 0 31263 7a1f drivers/scsi/wd719x.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Mon, 27 Nov 2017 11:36:25 +0000 (12:36 +0100)]
scsi: scsi_debug: remove jiffies_to_timespec
There is no need to go through an intermediate timespec to convert to
ktime_t when we just want a simple multiplication. This gets rid of one
of the few users of jiffies_to_timespec, which I hope to remove as part
of the y2038 cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dan Carpenter [Tue, 7 Nov 2017 13:01:32 +0000 (16:01 +0300)]
scsi: hpsa: remove an unnecessary NULL check
device->scsi3addr[] is an array, not a pointer, so it can't be NULL.
I've removed the check.
[mkp: fixed typo]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:44 +0000 (16:00 -0800)]
scsi: lpfc: update driver version to 11.4.0.5
Update the driver version to 11.4.0.5
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:43 +0000 (16:00 -0800)]
scsi: lpfc: small sg cnt cleanup
The logic for sg_seg_cnt is a bit convoluted. This patch tries to clean
up a couple of areas, especially around the +2 and +1 logic.
This patch:
- Cleans up the lpfc_sg_seg_cnt attribute to specify a real minimum
rather than making the minimum be whatever the default is.
- Removes the hardcoding of +2 (for the number of elements we use in a
sgl for cmd iu and rsp iu) and +1 (an additional entry to compensate
for nvme's reduction of io size based on a possible partial page)
logic in sg list initialization. In the case where the +1 logic is
referenced in host and target io checks, use the values set in the
transport template as that value was properly set.
There can certainly be more done in this area and it will be addressed
in combined host/target driver effort.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:42 +0000 (16:00 -0800)]
scsi: lpfc: Fix driver handling of nvme resources during unload
During driver unload, the driver may crash due to NULL pointers. The
NULL pointers were due to the driver not protecting itself sufficiently
during some of the teardown paths. Additionally, the driver was not
waiting for and cleanup up nvme io resources. As such, the driver wasn't
making the callbacks to the transport, stalling the transports
association teardown.
This patch waits for io clean up before tearding down and adds checks
for possible NULL pointers.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:41 +0000 (16:00 -0800)]
scsi: lpfc: Fix crash during driver unload with running nvme traffic
When the driver is unloading, the nvme transport could be in the process
of submitting new requests, will send abort requests to terminate
associations, or may make LS-related requests. The driver's abort and
request entry points currently is ignorant of the unloading state and is
starting the requests even though the infrastructure to complete them
continues to teardown.
Change the entry points for new requests to check whether unloading and
if so, reject the requests. Abort routines check unloading, and if so,
noop the request. An abort is noop'd as the teardown paths are already
aborting/terminating the io outstanding at the time the teardown
initiated.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:40 +0000 (16:00 -0800)]
scsi: lpfc: Correct driver deregistrations with host nvme transport
The driver's interaction with the host nvme transport has been incorrect
for a while. The driver did not wait for the unregister callbacks
(waited only 5 jiffies). Thus the driver may remove objects that may be
referenced by subsequent abort commands from the transport, and the
actual unregister callback was effectively a noop. This was especially
problematic if the driver was unloaded.
The driver now waits for the unregister callbacks, as it should, before
continuing with teardown.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:39 +0000 (16:00 -0800)]
scsi: lpfc: correct port registrations with nvme_fc
The driver currently registers any remote port that has NVME support.
It should only be registering target ports.
Register only target ports.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:38 +0000 (16:00 -0800)]
scsi: lpfc: Linux LPFC driver does not process all RSCNs
During RSCN storms, the driver does not rediscover some targets. The
driver marks some RSCN as to be handled after the ones it's working
on. The driver missed processing some deferred RSCN.
Move where the driver checks for deferred RSCNs and initiate deferred
RSCN handling if the flag was set. Also revise nport state within the
RSCN confirm routine. Add some state data to a possible debug print to
aid future debugging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:37 +0000 (16:00 -0800)]
scsi: lpfc: Fix ndlp ref count for pt2pt mode issue RSCN
pt2pt ndlp ref count prematurely goes to 0. There was reference removed
that should only be removed if connected to a switch, not if in
point-to-point mode.
Add a mode check before the reference remove.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:36 +0000 (16:00 -0800)]
scsi: lpfc: Adjust default value of lpfc_nvmet_mrq
The current default for async hw receive queues is 1, which presents
issues under heavy load as number of queues influence the available
async receive buffer limits.
Raise the default to the either the current hw limit (16) or the number
of hw qs configured (io channel value).
Revise the attribute definition for mrq to better reflect what we do for
hw queues. E.g. 0 means default to optimal (# of cpus), non-zero
specifies a specific limit. Before this change, mrq=0 meant target mode
was disabled. As 0 now has a different meaning, rework the if tests to
use the better nvmet_support check.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:35 +0000 (16:00 -0800)]
scsi: lpfc: Fix display for debugfs queInfo
Display for lpfc/fnX/iDiag/queInfo isn't formatted perfectly. Corrected
the format strings for the queue info debug messages.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:34 +0000 (16:00 -0800)]
scsi: lpfc: Driver fails to detect direct attach storage array
The driver does not respond to PLOGI from the direct attach target. The
driver uses incorrect S_ID in CONFIG_LINK, after FLOGI completion
Correct by issuing CONFIG_LINK with the correct S_ID after receiving the
PLOGI from the target
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:33 +0000 (16:00 -0800)]
scsi: lpfc: Raise maximum NVME sg list size for 256 elements
Raise the maximum NVME sg list size allowed to 256 elements.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:32 +0000 (16:00 -0800)]
scsi: lpfc: Fix NVME LS abort_xri
Performing an LS abort results in the following message being seen:
0603 Invalid CQ subtype 6:
00000300 22000002 ffff0016 d0050000
and the associated exchange is not properly freed.
The code did not recognize the exchange type that was aborted, thus it
was not properly handled.
Correct by adding the NVME LS ELS type to the exchange types that are
recognized.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:31 +0000 (16:00 -0800)]
scsi: lpfc: Fix crash after bad bar setup on driver attachment
In test cases where an instance of the driver is detached and
reattached, the driver will crash on reattachment. There is a compound
if statement that will skip over the bar setup if the pci_resource_start
call is not successful. The driver erroneously returns success to its
bar setup in this scenario even though the bars aren't properly
configured.
Rework the offending code segment for proper initialization steps. If
the pci_resource_start call fails, -ENOMEM is now returned.
Sample stack:
rport-5:0-10: blocked FC remote port time out: removing rport
BUG: unable to handle kernel NULL pointer dereference at (null)
... lpfc_sli4_wait_bmbx_ready+0x32/0x70 [lpfc]
...
... RIP: 0010:... ... lpfc_sli4_wait_bmbx_ready+0x32/0x70 [lpfc]
Call Trace:
... lpfc_sli4_post_sync_mbox+0x106/0x4d0 [lpfc]
... ? __alloc_pages_nodemask+0x176/0x420
... ? __kmalloc+0x2e/0x230
... lpfc_sli_issue_mbox_s4+0x533/0x720 [lpfc]
... ? mempool_alloc+0x69/0x170
... ? dma_generic_alloc_coherent+0x8f/0x140
... lpfc_sli_issue_mbox+0xf/0x20 [lpfc]
... lpfc_sli4_driver_resource_setup+0xa6f/0x1130 [lpfc]
... ? lpfc_pci_probe_one+0x23e/0x16f0 [lpfc]
... lpfc_pci_probe_one+0x445/0x16f0 [lpfc]
... local_pci_probe+0x45/0xa0
... work_for_cpu_fn+0x14/0x20
... process_one_work+0x17a/0x440
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:30 +0000 (16:00 -0800)]
scsi: lpfc: Handle XRI_ABORTED_CQE in soft IRQ
XRI_ABORTED_CQE completions were not being handled in the fast path.
They were being queued and deferred to the lpfc worker thread for
processing. This is an artifact of the driver design prior to moving
queue processing out of the isr and into a workq element. Now that queue
processing is already in a deferred context, remove this artifact and
process them directly.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:29 +0000 (16:00 -0800)]
scsi: lpfc: Expand WQE capability of every NVME hardware queue
Hardware queues are a fast staging area to push commands into the
adapter. The adapter should drain them extremely quickly. However,
under heavy io load, the host cpu is pushing commands faster than the
drain rate of the adapter causing the driver to resource busy commands.
Enlarge the hardware queue (wq & cq) to support a larger number of queue
entries (4x the prior size) before backpressure. Enlarging the queue
requires larger contiguous buffers (16k) per logical page for the
hardware. This changed calling sequences that were expecting 4K page
sizes that now must pass a parameter with the page sizes. It also
required use of a new version of an adapter command that can vary the
page size values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 21 Nov 2017 00:00:28 +0000 (16:00 -0800)]
scsi: lpfc: FLOGI failures are reported when connected to a private loop.
When the HBA is connected to a private loop, the driver reports FLOGI
loop-open failure as functional error. This is an expected condition.
Mark loop-open failure as a warning instead of error.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Wed, 15 Nov 2017 17:08:49 +0000 (17:08 +0000)]
scsi: bfa: remove unused pointer 'port'
The pointer 'port' is being assigned but it is never read, hence it is
redundant and can be removed. Cleans up clang warning:
drivers/scsi/bfa/bfad_attr.c:505:2: warning: Value stored to 'port' is
never read.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Wed, 15 Nov 2017 16:53:41 +0000 (16:53 +0000)]
scsi: aacraid: remove unused variable managed_request_id
Variable managed_request_id is being assigned but it is never read,
hence it is redundant and can be removed. Cleans up clang warning:
drivers/scsi/aacraid/linit.c:706:5: warning: Value stored to
'managed_request_id' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Randy Dunlap [Tue, 21 Nov 2017 02:25:08 +0000 (18:25 -0800)]
scsi: st: fix kernel-doc mismatch
Fix kernel-doc function name and comments in st.c::read_ns_show():
change us to ns to match the function name.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Randy Dunlap [Sun, 19 Nov 2017 01:46:59 +0000 (17:46 -0800)]
scsi: fix another I2O typo
Correct another typo I20 to I2O.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Greg Kroah-Hartman [Fri, 17 Nov 2017 14:21:22 +0000 (15:21 +0100)]
scsi: csiostor: remove unneeded DRIVER_LICENSE #define
There is no need to #define the license of the driver, just put it in
the MODULE_LICENSE() line directly as a text string.
This allows tools that check that the module license matches the source
code license to work properly, as there is no need to unwind the
unneeded dereference, especially when the string is defined in a .h file
far away from the .c file it is used in.
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Varun Prakash <varun@chelsio.com>
Reported-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Fri, 10 Nov 2017 15:58:27 +0000 (16:58 +0100)]
scsi: 3w-9xxx: rework lock timeouts
The TW_IOCTL_GET_LOCK ioctl uses do_gettimeofday() to check whether a
lock has expired. This can misbehave due to a concurrent settimeofday()
call, as it is based on 'real' time, and it will overflow in y2038 on
32-bit architectures, producing unexpected results when used across the
overflow time.
This changes it to using monotonic time, using ktime_get() to simplify
the code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Fri, 10 Nov 2017 15:58:26 +0000 (16:58 +0100)]
scsi: 3ware: use 64-bit times for FW time sync
The calculation of the number of seconds since Sunday 00:00:00 overflows
in 2106, meaning that we instead will return the seconds since Wednesday
06:28:16 afterwards.
Using 64-bit time stamps avoids this slight inconsistency, and the
deprecated do_gettimeofday(), replacing it with the simpler
ktime_get_real_seconds().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Fri, 10 Nov 2017 15:58:25 +0000 (16:58 +0100)]
scsi: 3ware: fix 32-bit time calculations
twl_aen_queue_event/twa_aen_queue_event, we use do_gettimeofday() to
read the lower 32 bits of the current time in seconds, to pass them to
the TW_IOCTL_GET_NEXT_EVENT ioctl or the 3ware_aen_read sysfs file.
This will overflow on all architectures in year 2106, there is not much
we can do about that without breaking the ABI. User space has 90 years
to learn to deal with it, so it's probably ok.
I'm changing it to use ktime_get_real_seconds() with a comment to
document what happens when.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Fri, 10 Nov 2017 15:37:15 +0000 (16:37 +0100)]
scsi: bfa: use 64-bit times in bfa_aen_entry_s ABI
bfa_aen_entry_s is passed through a netlink socket that can be read by
either 32-bit or 64-bit processes, but the data format is different
between the two on current implementations.
Originally, this was using a 'struct timeval', which also suffers from
getting redefined with a new libc implementation.
With this patch, the layout gets fixed to having two 64-bit members for
the time, making it the same on 32-bit kernels and 64-bit kernels
running either compat or native user space including x32.
Provided that the new header file gets used to recompile any 32-bit
application binaries, this will fix running those on a 64-bit kernel
(with or without this patch) e.g. in a container environment, and it
will make binaries work that will be built against a future 32-bit glibc
that uses a 64-bit time_t, and avoid the y2038 overflow there.
However, this also breaks compatibility with any existing 32-bit binary
running on a native 32-bit kernel, those must be recompiled against the
new header, which in turn makes them incompatible with older kernels
unless the same change gets applied there.
Obviously this patch should only be applied when the benefits outweigh
the possible breakage. I'm posting it under the assumption that there
are no open-source tools using the netlink interface, and that users of
the binaries provided by qlogic for SLES10/11 and RHEL5/6 are not
actually being used on new future systems with 32-bit x86 kernels.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Anil Gurumurthy <Anil.Gurumurthy@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Fri, 10 Nov 2017 15:37:14 +0000 (16:37 +0100)]
scsi: bfa: try to sanitize vendor netlink events
bfa_aen_entry_s is passed to user space in a netlink message, but is
defined using a 'struct timeval' and an 'enum' that are not only
different between architectures, but also between 32-bit user space and
64-bit kernels they may run on, as well as depending on the particular C
library that defines timeval.
This changes the in-kernel definition to no longer use the timeval type
directly but instead use two open-coded 'unsigned long' members. This
keeps the existing ABI, but making the variable unsigned also helps make
it work after y2038, until it overflows in 2106.
Since the macro becomes overly complex at this point, I'm changing it to
an inline function for readability.
I'm not changing the 32-bit user-space ABI at this point, to keep the
changes separate, I deally this would be defined using the same binary
layout for all architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Anil Gurumurthy <Anil.Gurumurthy@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Fri, 10 Nov 2017 15:37:13 +0000 (16:37 +0100)]
scsi: bfa: replace bfa_get_log_time() with ktime_get_real_seconds()
The bfa_get_log_time() returns a 64-bit timestamp that does not suffer
from the y2038 overflow on 64-bit systems. However, on 32-bit
architectures the timestamp will jump from 0x000000007fffffff to
0xffffffff80000000 in y2038 and produce wrong results.
The ktime_get_real_seconds() function does the same thing as
bfa_get_log_time() without that problem, so we can simply remove the
former use ktime_get_real_seconds() instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Anil Gurumurthy <Anil.Gurumurthy@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Fri, 10 Nov 2017 15:37:12 +0000 (16:37 +0100)]
scsi: bfa: document overflow of io_profile_start_time
io_profile_start_time() gets read using do_gettimeofday() and passed
down as a 32-bit value through multiple functions. This will overflow in
y2038 or y2106, depending on whether it gets interpreted as unsigned in
the end.
This changes do_gettimeofday() to ktime_get_real_seconds() and pushes
the point at which it overflows to where we actually assign it to the
bfa_fcpim_del_itn_stats_s structure, with an appropriate comment.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Anil Gurumurthy <Anil.Gurumurthy@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Fri, 10 Nov 2017 15:37:11 +0000 (16:37 +0100)]
scsi: bfa: improve bfa_ioc_send_enable/disable data
In bfa_ioc_send_enable, we use the deprecated do_gettimeofday() function
to read the current time. This is not a problem, since the firmware
interface is already limited to 32-bit timestamps, but it's better to
use ktime_get_seconds() and document what the limitation is.
I noticed that I did the same change in commit
a5af83925363 ("bna: avoid
writing uninitialized data into hw registers") for the ethernet
driver. That commit also changed the "disable" funtion to initialize the
data we pass to the firmware properly, so I'm doing the same thing here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Anil Gurumurthy <Anil.Gurumurthy@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Fri, 10 Nov 2017 15:37:10 +0000 (16:37 +0100)]
scsi: bfa: use proper time accessor for stats_reset_time
We use the deprecated do_gettimeofday() function to read the current
time when resetting the statistics in both bfa_port and bfa_svc. This
works fine because overflow is handled correctly, but we want to get rid
of do_gettimeofday() and using a non-monotonic time suffers from
concurrent settimeofday calls and other problems.
This uses the ktime_get_seconds() function instead, which does what we
need here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Anil Gurumurthy <Anil.Gurumurthy@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Fri, 10 Nov 2017 15:37:09 +0000 (16:37 +0100)]
scsi: bfa: use ktime_get_real_ts64 for firmware timestamp
BFA_TRC_TS() calculates a 32-bit microsecond timestamp using the
deprecated do_gettimeofday() function. This overflows roughly every 71
minutes, so it's obviously not used as an absolute time stamp, but it
seems wrong to use a time base for it that will jump during
settimeofday() calls, leap seconds, or the y2038 overflow.
This converts it to ktime_get_ts64(), which has none of those problems
but is not synchronized to wall-clock time.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Anil Gurumurthy <Anil.Gurumurthy@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gustavo A. R. Silva [Wed, 8 Nov 2017 17:17:39 +0000 (11:17 -0600)]
scsi: ppa: mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114988
Addresses-Coverity-ID: 114989
Addresses-Coverity-ID: 114990
Addresses-Coverity-ID: 114991
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gustavo A. R. Silva [Fri, 3 Nov 2017 19:58:39 +0000 (14:58 -0500)]
scsi: bnx2i: bnx2i_hwi: use swap macro in bnx2i_send_iscsi_nopout
Make use of the swap macro and remove unnecessary variable tmp. This
makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Linus Torvalds [Mon, 27 Nov 2017 00:01:47 +0000 (16:01 -0800)]
Linux 4.15-rc1
Linus Torvalds [Sun, 26 Nov 2017 23:03:49 +0000 (15:03 -0800)]
Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- LPAE fixes for kernel-readonly regions
- Fix for get_user_pages_fast on LPAE systems
- avoid tying decompressor to a particular platform if DEBUG_LL is
enabled
- BUG if we attempt to return to userspace but the to-be-restored PSR
value keeps us in privileged mode (defeating an issue that ftracetest
found)
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: BUG if jumping to usermode address in kernel mode
ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE
ARM: 8721/1: mm: dump: check hardware RO bit for LPAE
ARM: make decompressor debug output user selectable
ARM: fix get_user_pages_fast
Linus Torvalds [Sun, 26 Nov 2017 22:39:20 +0000 (14:39 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fixes from Thomas Glexiner:
- unbreak the irq trigger type check for legacy platforms
- a handful fixes for ARM GIC v3/4 interrupt controllers
- a few trivial fixes all over the place
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/matrix: Make - vs ?: Precedence explicit
irqchip/imgpdc: Use resource_size function on resource object
irqchip/qcom: Fix u32 comparison with value less than zero
irqchip/exiu: Fix return value check in exiu_init()
irqchip/gic-v3-its: Remove artificial dependency on PCI
irqchip/gic-v4: Add forward definition of struct irq_domain_ops
irqchip/gic-v3: pr_err() strings should end with newlines
irqchip/s3c24xx: pr_err() strings should end with newlines
irqchip/gic-v3: Fix ppi-partitions lookup
irqchip/gic-v4: Clear IRQ_DISABLE_UNLAZY again if mapping fails
genirq: Track whether the trigger type has been set
Linus Torvalds [Sun, 26 Nov 2017 22:11:54 +0000 (14:11 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull misc x86 fixes from Ingo Molnar:
- topology enumeration fixes
- KASAN fix
- two entry fixes (not yet the big series related to KASLR)
- remove obsolete code
- instruction decoder fix
- better /dev/mem sanity checks, hopefully working better this time
- pkeys fixes
- two ACPI fixes
- 5-level paging related fixes
- UMIP fixes that should make application visible faults more debuggable
- boot fix for weird virtualization environment
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/decoder: Add new TEST instruction pattern
x86/PCI: Remove unused HyperTransport interrupt support
x86/umip: Fix insn_get_code_seg_params()'s return value
x86/boot/KASLR: Remove unused variable
x86/entry/64: Add missing irqflags tracing to native_load_gs_index()
x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing
x86/pkeys/selftests: Fix protection keys write() warning
x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
x86/mpx/selftests: Fix up weird arrays
x86/pkeys: Update documentation about availability
x86/umip: Print a warning into the syslog if UMIP-protected instructions are used
x86/smpboot: Fix __max_logical_packages estimate
x86/topology: Avoid wasting 128k for package id array
perf/x86/intel/uncore: Cache logical pkg id in uncore driver
x86/acpi: Reduce code duplication in mp_override_legacy_irq()
x86/acpi: Handle SCI interrupts above legacy space gracefully
x86/boot: Fix boot failure when SMP MP-table is based at 0
x86/mm: Limit mmap() of /dev/mem to valid physical addresses
x86/selftests: Add test for mapping placement for 5-level paging
...
Linus Torvalds [Sun, 26 Nov 2017 21:43:25 +0000 (13:43 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: a documentation fix, a Sparse warning fix and a debugging
fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/debug: Fix task state recording/printout
sched/deadline: Don't use dubious signed bitfields
sched/deadline: Fix the description of runtime accounting in the documentation
Linus Torvalds [Sun, 26 Nov 2017 21:41:48 +0000 (13:41 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc fixes: two PMU driver fixes and a memory leak fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix memory leak triggered by perf --namespace
perf/x86/intel/uncore: Add event constraint for BDX PCU
perf/x86/intel: Hide TSX events when RTM is not supported
Linus Torvalds [Sun, 26 Nov 2017 21:36:54 +0000 (13:36 -0800)]
Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull static key fix from Ingo Molnar:
"Fix a boot warning related to bad init ordering of the static keys
self-test"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
jump_label: Invoke jump_label_test() via early_initcall()
Linus Torvalds [Sun, 26 Nov 2017 21:11:18 +0000 (13:11 -0800)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull objtool fixes from Ingo Molnar:
"A handful of objtool fixes, most of them related to making the UAPI
header-syncing warnings easier to read and easier to act upon"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools/headers: Sync objtool UAPI header
objtool: Fix cross-build
objtool: Move kernel headers/code sync check to a script
objtool: Move synced files to their original relative locations
objtool: Make unreachable annotation inline asms explicitly volatile
objtool: Add a comment for the unreachable annotation macros