OSDN Git Service
Teresa Remmet [Fri, 18 Feb 2022 12:04:57 +0000 (13:04 +0100)]
arm64: dts: imx8mp-phycore-som: LDO5 needs to be enabled instead of LDO4
LDO4 is not connected so disable it. And LDO5 is used for VSEL of
the NVCC_SD2 SD-Card bus. Having it disabled seems not to have an
impact on the functionality. We enable it, as it is used.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Teresa Remmet [Fri, 18 Feb 2022 12:04:56 +0000 (13:04 +0100)]
arm64: dts: imx8mp-phycore-som: Set VDD_ARM run and standby voltage
Add bindings for VDD_ARM (BUCK2) run and standby voltage.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Teresa Remmet [Fri, 18 Feb 2022 12:04:55 +0000 (13:04 +0100)]
arm64: dts: imx8mp-phycore-som: Update WDOG muxing
To be able to trigger a reset also from an external source we
need to configure the WDOG pin as open drain.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Teresa Remmet [Fri, 18 Feb 2022 12:04:54 +0000 (13:04 +0100)]
arm64: dts: imx8mp-phycore-som: Reduce drive strength for fec tx lines
Reduce drive strength on fec tx lines for signal quality improvements.
Measurements showed that TD0 and TD1 require X4 and the other lines
X2 for optimized settings.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Teresa Remmet [Fri, 18 Feb 2022 12:04:53 +0000 (13:04 +0100)]
arm64: dts: imx8mp-phycore-som: Adapt eMMC drive strength
Set eMMC drive strength for USDHC3_DATA lines (200Mhz)
to X4 for signal improvement.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Teresa Remmet [Fri, 18 Feb 2022 12:04:52 +0000 (13:04 +0100)]
arm64: dts: imx8mp-phycore-som: Set minimum output impedance for eth phy
To fit spec requirements set minimum output impedance for dp83867
ethernet phy.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Mon, 14 Feb 2022 23:14:24 +0000 (15:14 -0800)]
arm64: dts: imx8mm-venice-gw72xx-0x: add dt overlay for imx219 rpi v2 camera
Add support for the RaspberryPi Camera v2 which is an IMX219 8MP module:
- https://datasheets.raspberrypi.com/camera/camera-v2-schematics.pdf
- has its own on-board 24MHz osc so no clock required from baseboard
- pin 11 enables 1.8V and 2.8V LDO which is connected to
GW73xx MIPI_GPIO4 (IMX8MM GPIO1_IO1) so we use this as a gpio
Support is added via a device-tree overlay.
The IMX219 supports RAW8/RAW10 image formats.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Mon, 14 Feb 2022 23:14:23 +0000 (15:14 -0800)]
arm64: dts: imx8mm-venice-gw73xx-0x: add dt overlay for imx219 rpi v2 camera
Add support for the RaspberryPi Camera v2 which is an IMX219 8MP module:
- https://datasheets.raspberrypi.com/camera/camera-v2-schematics.pdf
- has its own on-board 24MHz osc so no clock required from baseboard
- pin 11 enables 1.8V and 2.8V LDO which is connected to
GW73xx MIPI_GPIO4 (IMX8MM GPIO1_IO1) so we use this as a gpio
controlled regulator enable.
Support is added via a device-tree overlay.
The IMX219 supports RAW8/RAW10 image formats.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Mon, 14 Feb 2022 23:14:22 +0000 (15:14 -0800)]
arm64: dts: imx8mm-venice-gw72xx-0x: add dt overlays for serial modes
The imx8mm-venice-gw72xx-0x som+baseboard combination has a multi-protocol
RS-232/RS-485/RS-422 transceiver to an off-board connector which
can be configured in a number of ways via UART and GPIO configuration.
The default configuration per the imx8mm-venice-gw72xx-0x dts is for
UART2 TX/RX and UART4 TX/RX to be available as RS-232:
J15.1 UART2 TX out
J15.2 UART2 RX in
J15.3 UART4 TX out
J15.4 UART4 RX in
J15.5 GND
Add dt overlays to allow additional the modes of operation:
rs232-rts (UART2 RS-232 with RTS/CTS hardware flow control)
J15.1 TX out
J15.2 RX in
J15.3 RTS out
J15.4 CTS in
J15.5 GND
rs485 (UART2 RS-485 half duplex)
J15.1 TXRX-
J15.2 N/C
J15.3 TXRX+
J15.4 N/C
J15.5 GND
rs422 (UART2 RS-422 full duplex)
J15.1 TX-
J15.2 RX+
J15.3 TX+
J15.4 RX-
J15.5 GND
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Mon, 14 Feb 2022 23:14:21 +0000 (15:14 -0800)]
arm64: dts: imx8mm-venice-gw73xx-0x: add dt overlays for serial modes
The imx8mm-venice-gw73xx-0x som+baseboard combination has a multi-protocol
RS-232/RS-485/RS-422 transceiver to an off-board connector which
can be configured in a number of ways via UART and GPIO configuration.
The default configuration per the imx8mm-venice-gw73xx-0x dts is for
UART2 TX/RX and UART4 TX/RX to be available as RS-232:
J15.1 UART2 TX out
J15.2 UART2 RX in
J15.3 UART4 TX out
J15.4 UART4 RX in
J15.5 GND
Add dt overlays to allow additional the modes of operation:
rs232-rts (UART2 RS-232 with RTS/CTS hardware flow control)
J15.1 TX out
J15.2 RX in
J15.3 RTS out
J15.4 CTS in
J15.5 GND
rs485 (UART2 RS-485 half duplex)
J15.1 TXRX-
J15.2 N/C
J15.3 TXRX+
J15.4 N/C
J15.5 GND
rs422 (UART2 RS-422 full duplex)
J15.1 TX-
J15.2 RX+
J15.3 TX+
J15.4 RX-
J15.5 GND
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Fri, 11 Feb 2022 19:04:18 +0000 (11:04 -0800)]
arm64: dts: imx: Add i.mx8mm Gateworks gw7903 dts support
The GW7903 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD connector with UHS support
- LIS2DE12 3-axis accelerometer
- Gateworks System Controller
- IMX8M FEC
- software selectable RS232/RS485/RS422 serial transceiver
- PMIC
- 2x off-board bi-directional opto-isolated digital I/O
- 1x M.2 A-E Key Socket and 1x MiniPCIe socket with USB2.0 and PCIe
(resistor loading to route PCIe/USB2 between M.2 and MiniPCIe socket)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michael Walle [Mon, 14 Feb 2022 11:55:29 +0000 (12:55 +0100)]
arm64: dts: ls1028a: add efuse node
Layerscape SoCs contain a Security Fuse Processor which is basically a
efuse controller. Add the node, so userspace can read the efuses.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Hugo Villeneuve [Fri, 11 Feb 2022 15:38:43 +0000 (10:38 -0500)]
arm64: dts: imx8mp-evk: add support for I2C5
Add support for i2c5, which is used to access the
external I2C bus on connector J22 of the imx8mp-evk.
Limit the speed to 100kHz since this is an external I2C bus.
Disabled by default, since it is shared with the CAN1 bus.
To enable i2c5, you need to disable the CAN1 function, enable the i2c5
function and also configure the CAN1/I2C5_SEL GPIO to HIGH to
select i2c5 instead of CAN1. This can be done by defining a gpio-hog
inside the pca6416 node, in your board device tree, like in this example:
&flexcan1 {
status = "disabled";
};
&i2c5 {
status = "okay";
};
&pca6416 {
can1-i2c5-sel-hog {
gpio-hog;
gpios = <2 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "can1-i2c5-sel";
};
};
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Hugo Villeneuve [Fri, 11 Feb 2022 15:38:17 +0000 (10:38 -0500)]
arm64: dts: imx8mp-evk: add PCA6416 gpio line names
Add gpio-line-names for the various GPIO's connected to the PCA6416
I/O expander on the imx8mp EVK.
This helps when using the new gpiod interface to find the GPIOs by name.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oliver Graute [Wed, 9 Feb 2022 15:50:55 +0000 (16:50 +0100)]
arm64: dts: imx8qm: added more serial alias to dts
Add more serial alias to imx8qm.dtsi file
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oliver Graute [Wed, 9 Feb 2022 15:42:23 +0000 (16:42 +0100)]
arm64: dts: imx8qm: add compatible string for usdhc3
add compatible string for usdhc3
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Richard Zhu [Wed, 9 Feb 2022 02:06:48 +0000 (10:06 +0800)]
arm64: dts: imx8mq-evk: Add second PCIe port support
Enable the second PCIe port support on i.MX8MQ EVK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Sat, 5 Feb 2022 17:31:01 +0000 (11:31 -0600)]
arm64: dts: imx8mm-beacon: Enable PCIe
The baseboard supports a PCIe slot with a 100MHz reference clock,
but it's controlled by a different GPIO, so a gated clock is
required.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marcel Ziswiler [Fri, 11 Feb 2022 09:23:22 +0000 (10:23 +0100)]
arm64: dts: freescale: add initial support for verdin imx8m mini
This patch adds the device tree to support Toradex Verdin iMX8M Mini a
computer on module which can be used on different carrier boards.
The module consists of an NXP i.MX 8M Mini family SoC (either i.MX 8M
Mini Quad or 8M Mini DualLite), a PCA9450A PMIC, a Gigabit Ethernet PHY,
1 or 2 GB of LPDDR4 RAM, an eMMC, a TLA2024 ADC, an I2C EEPROM, an
RX8130 RTC, an optional SPI CAN controller plus an optional Bluetooth/
Wi-Fi module.
Anything that is not self-contained on the module is disabled by
default.
The device tree for the Dahlia includes the module's device tree and
enables the supported peripherals of the carrier board.
The device tree for the Verdin Development Board includes the module's
device tree as well as the Dahlia one as it is a superset and supports
almost all peripherals available.
So far there is no display functionality supported at all but basic
console UART, PCIe, USB host, eMMC and Ethernet and PCIe functionality
work fine.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Hugo Villeneuve [Sat, 29 Jan 2022 20:26:17 +0000 (15:26 -0500)]
arm64: dts: imx8mp-evk: add PCA6416 interrupt controller mode
Add interrupt controller mode for the pca6416 on i.MX8MP EVK board's.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Shawn Guo [Wed, 26 Jan 2022 08:54:20 +0000 (16:54 +0800)]
arm64: dts: freescale: Use overlay target for simplicity
With commit
15d16d6dadf6 ("kbuild: Add generic rule to apply
fdtoverlay"), overlay target can be used to simplify the build of DTB
overlays. It also performs a cross check to ensure base DT and overlay
actually match.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Shawn Guo [Wed, 26 Jan 2022 08:49:40 +0000 (16:49 +0800)]
arm64: dts: fsl-ls1028a-qds: Drop overlay syntax hard coding
As suggested by commit
9ae8578b517a ("of: Documentation: change overlay
example to use current syntax"), there is no need to have overlay syntax
be hard coded in the device tree source file any more.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Marcel Ziswiler [Fri, 28 Jan 2022 16:00:49 +0000 (17:00 +0100)]
arm64: dts: imx8mm: fix strange hex notation
Fix strange hex notation with mixed lower-case and upper-case letters.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reinhold Mueller [Thu, 27 Jan 2022 15:35:00 +0000 (16:35 +0100)]
arm64: dts: imx8mm: Add support for emtrion emCON-MX8M Mini
This patch adds support for the emtrion GmbH emCON-MX8M Mini modules.
They are available with NXP i.MX 8M Mini equipped with 2 or 4 GB Memory.
The devicetree imx8mm-emcon.dtsi is the common part providing all
module components and the basic support for the SoC. The support for the
avari baseboard in the developer-kit configuration is provided by the
emcon-avari dts files.
Signed-off-by: Reinhold Mueller <reinhold.mueller@emtrion.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Stein [Wed, 26 Jan 2022 13:23:38 +0000 (14:23 +0100)]
arm64: dts: tqma8mqml: add PCIe support
Add PCIe support to TQMa8MxML series.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Tue, 25 Jan 2022 17:11:28 +0000 (11:11 -0600)]
arm64: dts: imx8mm: Enable Hantro G1 and G2 video decoders
There are two decoders on the i.MX8M Mini controlled by the
vpu-blk-ctrl. The G1 supports H264 and VP8 while the
G2 support HEVC and VP9.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Tue, 25 Jan 2022 17:11:24 +0000 (11:11 -0600)]
arm64: dts: imx8mq: Enable both G1 and G2 VPU's with vpu-blk-ctrl
With the Hantro G1 and G2 now setup to run independently, update
the device tree to allow both to operate. This requires the
vpu-blk-ctrl node to be configured. Since vpu-blk-ctrl needs
certain clock enabled to handle the gating of the G1 and G2
fuses, the clock-parents and clock-rates for the various VPU's
to be moved into the pgc_vpu because they cannot get re-parented
once enabled, and the pgc_vpu is the highest in the chain.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Shawn Guo [Fri, 11 Feb 2022 03:21:29 +0000 (11:21 +0800)]
Adam Ford [Tue, 25 Jan 2022 17:11:18 +0000 (11:11 -0600)]
arm64: dts: imx8mq-tqma8mq: Remove redundant vpu reference
The vpu is enabled by default, so there is no need to manually
enable it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Wed, 26 Jan 2022 09:26:50 +0000 (03:26 -0600)]
arm64: dts: ls1028a-qds: define mdio slots for networking options
The ls1028a QDS board support different pluggable PHY cards. Define the
nodes for these slots to be updated at boot time with overlay according
to board setup.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Fri, 28 Jan 2022 01:06:03 +0000 (17:06 -0800)]
arm64: dts: imx8m{m,n}_venice*: add gpio-line-names
Add gpio-line-names for the various GPIO's used on Gateworks Venice
boards. Note that these GPIO's are typically 'configured' in Boot
Firmware via gpio-hog therefore we only configure line names to keep the
boot firmware configuration from changing on kernel init.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Thu, 16 Dec 2021 16:12:27 +0000 (08:12 -0800)]
arm64: dts: imx8mn-venice-gw7902: disable gpu
Since commit
9a0f3b157e22 ("arm64: dts: imx8mn: Enable GPU")
imx8mn-venice-gw7902 will hang during kernel init because it uses
a MIMX8MN5CVTI which does not have a GPU.
Disable pgc_gpumix to work around this. We also disable the GPU devices
that depend on the gpumix power domain and pgc_gpu to avoid them staying
in a probe deferred state forever.
Cc: Adam Ford <aford173@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Fixes:
9a0f3b157e22 ("arm64: dts: imx8mn: Enable GPU")
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marek Vasut [Tue, 25 Jan 2022 02:54:09 +0000 (03:54 +0100)]
arm64: dts: imx8mm: Add missing MX8MM_IOMUXC_NAND_READY_B_SD3_RESET_B
The i.MX8M Mini Application Processor Reference Manual, Rev. 3, 11/2020
documents AF MX8MM_IOMUXC_NAND_READY_B_SD3_RESET_B , add it into the
pinmux tables.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lucas Stach [Wed, 19 Jan 2022 13:23:48 +0000 (14:23 +0100)]
arm64: dts: imx8mp: disable usb3_phy1
Like usb3_phy0 the default state of the usb3_phy1 should be disabled, so
it is only enabled on boards exposing this USB port.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Abel Vesa [Tue, 18 Jan 2022 13:59:18 +0000 (15:59 +0200)]
arm64: dts: imx8qxp-ss-adma: Drop fsl,imx7ulp-lpuart comaptible
The driver differs from clocks point of view, so the i.MX8QXP
is not backwards compatible with i.MX7ULP.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Peng Fan [Tue, 11 Jan 2022 06:20:13 +0000 (14:20 +0800)]
arm64: dts: imx8: add mu5/6 node
Add mu5/6 for i.MX8QXP/QM, these two mu will be used for
communicating with general purpose Cortex-M4 cores.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Abel Vesa [Mon, 3 Jan 2022 22:49:00 +0000 (00:49 +0200)]
arm64: dts: imx8qm: Add SCU RTC node
Add SCU RTC node to support SC RTC driver.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lucas Stach [Sat, 18 Dec 2021 18:20:21 +0000 (19:20 +0100)]
arm64: dts: mnt-reform2: correct i2c3 pad-ctrl
The slew rate and drive-strength of the i2c3 pads were much too
high. Bring them down to avoid signal quality issues.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lucas Stach [Sat, 18 Dec 2021 18:20:20 +0000 (19:20 +0100)]
arm64: dts: mnt-reform2: add internal display support
This adds support for the internal display of the Reform2 Laptop, which
is connected to the i.MX8MQ via a MIPI-DSI->eDP bridge chip. Clocking
is derived from a system PLL, which provides quite good rate matching
for the single supported display mode and keeps the video PLL free for
usage with the external display, which isn't supported yet.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lucas Stach [Sat, 18 Dec 2021 18:18:08 +0000 (19:18 +0100)]
arm64: dts: imx8mq: disable DDRC node by default
Without a OPP table or a downstream TF-A running on the system the DDRC will
fail to probe, as it has no means to scale the DRAM frequency in that case.
This however will block the bus scaling driver to come up and this in turn
prevents other devices that hook into the interconnect from probing.
If the DDRC is disabled, the interconnect driver will simply ignore it. As
most systems don't want to scale the DRAM frequency, disable the node by
default and only enable it on the systems that actually uses this
capability and provides a valid OPP table in the DT.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
David Jander [Fri, 17 Dec 2021 21:36:17 +0000 (22:36 +0100)]
arm64: dts: imx: add Protonic PRT8MM board
The Protonic PRT8MM is a low-cost agricultural Virtual Terminal. This
commit adds most of the board functionality sans the display output,
as the i.MX8MM display support isn't ready yet.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rob Herring [Fri, 17 Dec 2021 17:39:08 +0000 (11:39 -0600)]
arm64: dts: imx8qm: Drop CPU 'arm,armv8' compatible
The CPU 'arm,armv8' compatible is only for s/w models, so remove it from
i.MX8QM CPU nodes.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Thu, 16 Dec 2021 16:41:49 +0000 (08:41 -0800)]
arm64: dts: imx8mm-venice*: add PCIe support
Add PCIe support to GW71xx/GW72xx/GW73xx/GW7901/GW7902
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Wed, 15 Dec 2021 00:46:26 +0000 (18:46 -0600)]
arm64: dts: imx8mn: Enable GPU
The i.MX8M-Nano features a GC7000. The Etnaviv driver detects it as:
etnaviv-gpu
38000000.gpu: model: GC7000, revision: 6203
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Wed, 15 Dec 2021 00:46:25 +0000 (18:46 -0600)]
arm64: dts: imx8mn: add DISP blk-ctrl
Add the DT node for the DISP blk-ctrl. With this in place the
display/mipi power domains should be functional.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Wed, 15 Dec 2021 00:46:24 +0000 (18:46 -0600)]
arm64: dts: imx8mn: put USB controller into power-domains
Now that we have support for the power domain controller on the i.MX8MN,
we can put the USB controller in the respective power domain to allow
it to power down the PHY when possible.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Wed, 15 Dec 2021 00:46:23 +0000 (18:46 -0600)]
arm64: dts: imx8mn: add GPC node
Add the DT node for the GPC, including all the PGC power domains,
some of them are not fully functional yet, as they require interaction
with the blk-ctrls to properly power up/down the peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Richard Zhu [Thu, 2 Dec 2021 08:02:37 +0000 (16:02 +0800)]
arm64: dts: imx8mm-evk: Add the pcie support on imx8mm evk board
Add the PCIe support on iMX8MM EVK boards.
And set the default reference clock mode.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Richard Zhu [Thu, 2 Dec 2021 08:02:36 +0000 (16:02 +0800)]
arm64: dts: imx8mm: Add the pcie support
Add the PCIe support on i.MX8MM platforms.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Richard Zhu [Thu, 2 Dec 2021 08:02:34 +0000 (16:02 +0800)]
arm64: dts: imx8mm: Add the pcie phy support
Add the PCIe PHY support on iMX8MM platforms.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lucas Stach [Tue, 25 Jan 2022 17:11:19 +0000 (11:11 -0600)]
dt-bindings: power: imx8mq: add defines for VPU blk-ctrl domains
This adds the defines for the power domains provided by the VPU
blk-ctrl on the i.MX8MQ.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Linus Torvalds [Sun, 23 Jan 2022 08:12:53 +0000 (10:12 +0200)]
Linux 5.17-rc1
Linus Torvalds [Sun, 23 Jan 2022 06:14:21 +0000 (08:14 +0200)]
Merge tag 'perf-tools-for-v5.17-2022-01-22' of git://git./linux/kernel/git/acme/linux
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Fix printing 'phys_addr' in 'perf script'.
- Fix failure to add events with 'perf probe' in ppc64 due to not
removing leading dot (ppc64 ABIv1).
- Fix cpu_map__item() python binding building.
- Support event alias in form foo-bar-baz, add pmu-events and
parse-event tests for it.
- No need to setup affinities when starting a workload or attaching to
a pid.
- Use path__join() to compose a path instead of ad-hoc snprintf()
equivalent.
- Override attr->sample_period for non-libpfm4 events.
- Use libperf cpumap APIs instead of accessing the internal state
directly.
- Sync x86 arch prctl headers and files changed by the new
set_mempolicy_home_node syscall with the kernel sources.
- Remove duplicate include in cpumap.h.
- Remove redundant err variable.
* tag 'perf-tools-for-v5.17-2022-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf tools: Remove redundant err variable
perf test: Add parse-events test for aliases with hyphens
perf test: Add pmu-events test for aliases with hyphens
perf parse-events: Support event alias in form foo-bar-baz
perf evsel: Override attr->sample_period for non-libpfm4 events
perf cpumap: Remove duplicate include in cpumap.h
perf cpumap: Migrate to libperf cpumap api
perf python: Fix cpu_map__item() building
perf script: Fix printing 'phys_addr' failure issue
tools headers UAPI: Sync files changed by new set_mempolicy_home_node syscall
tools headers UAPI: Sync x86 arch prctl headers with the kernel sources
perf machine: Use path__join() to compose a path instead of snprintf(dir, '/', filename)
perf evlist: No need to setup affinities when disabling events for pid targets
perf evlist: No need to setup affinities when enabling events for pid targets
perf stat: No need to setup affinities when starting a workload
perf affinity: Allow passing a NULL arg to affinity__cleanup()
perf probe: Fix ppc64 'perf probe add events failed' case
Linus Torvalds [Sun, 23 Jan 2022 06:07:02 +0000 (08:07 +0200)]
Merge tag 'trace-v5.17-3' of git://git./linux/kernel/git/rostedt/linux-trace
Pull ftrace fix from Steven Rostedt:
"Fix s390 breakage from sorting mcount tables.
The latest merge of the tracing tree sorts the mcount table at build
time. But s390 appears to do things differently (like always) and
replaces the sorted table back to the original unsorted one. As the
ftrace algorithm depends on it being sorted, bad things happen when it
is not, and s390 experienced those bad things.
Add a new config to tell the boot if the mcount table is sorted or
not, and allow s390 to opt out of it"
* tag 'trace-v5.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix assuming build time sort works for s390
Steven Rostedt (Google) [Sat, 22 Jan 2022 14:17:10 +0000 (09:17 -0500)]
ftrace: Fix assuming build time sort works for s390
To speed up the boot process, as mcount_loc needs to be sorted for ftrace
to work properly, sorting it at build time is more efficient than boot up
and can save milliseconds of time. Unfortunately, this change broke s390
as it will modify the mcount_loc location after the sorting takes place
and will put back the unsorted locations. Since the sorting is skipped at
boot up if it is believed that it was sorted at run time, ftrace can crash
as its algorithms are dependent on the list being sorted.
Add a new config BUILDTIME_MCOUNT_SORT that is set when
BUILDTIME_TABLE_SORT but not if S390 is set. Use this config to determine
if sorting should take place at boot up.
Link: https://lore.kernel.org/all/yt9dee51ctfn.fsf@linux.ibm.com/
Fixes:
72b3942a173c ("scripts: ftrace - move the sort-processing in ftrace_init")
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Tested-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Linus Torvalds [Sun, 23 Jan 2022 04:32:29 +0000 (06:32 +0200)]
Merge tag 'kbuild-fixes-v5.17' of git://git./linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Bring include/uapi/linux/nfc.h into the UAPI compile-test coverage
- Revert the workaround of CONFIG_CC_IMPLICIT_FALLTHROUGH
- Fix build errors in certs/Makefile
* tag 'kbuild-fixes-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
certs: Fix build error when CONFIG_MODULE_SIG_KEY is empty
certs: Fix build error when CONFIG_MODULE_SIG_KEY is PKCS#11 URI
Revert "Makefile: Do not quote value for CONFIG_CC_IMPLICIT_FALLTHROUGH"
usr/include/Makefile: add linux/nfc.h to the compile-test coverage
Linus Torvalds [Sun, 23 Jan 2022 04:20:44 +0000 (06:20 +0200)]
Merge tag 'bitmap-5.17-rc1' of git://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- introduce for_each_set_bitrange()
- use find_first_*_bit() instead of find_next_*_bit() where possible
- unify for_each_bit() macros
* tag 'bitmap-5.17-rc1' of git://github.com/norov/linux:
vsprintf: rework bitmap_list_string
lib: bitmap: add performance test for bitmap_print_to_pagebuf
bitmap: unify find_bit operations
mm/percpu: micro-optimize pcpu_is_populated()
Replace for_each_*_bit_from() with for_each_*_bit() where appropriate
find: micro-optimize for_each_{set,clear}_bit()
include/linux: move for_each_bit() macros from bitops.h to find.h
cpumask: replace cpumask_next_* with cpumask_first_* where appropriate
tools: sync tools/bitmap with mother linux
all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate
cpumask: use find_first_and_bit()
lib: add find_first_and_bit()
arch: remove GENERIC_FIND_FIRST_BIT entirely
include: move find.h from asm_generic to linux
bitops: move find_bit_*_le functions from le.h to find.h
bitops: protect find_first_{,zero}_bit properly
Minghao Chi [Wed, 12 Jan 2022 08:01:09 +0000 (08:01 +0000)]
perf tools: Remove redundant err variable
Return value from perf_event__process_tracing_data() directly instead
of taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/20220112080109.666800-1-chi.minghao@zte.com.cn
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
John Garry [Mon, 17 Jan 2022 15:10:15 +0000 (23:10 +0800)]
perf test: Add parse-events test for aliases with hyphens
Add a test which allows us to test parsing an event alias with hyphens.
Since these events typically do not exist on most host systems, add the
alias to the fake pmu.
Function perf_pmu__test_parse_init() has terms added to match known test
aliases.
Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qi Liu <liuqi115@huawei.com>
Cc: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: linuxarm@huawei.com
Link: https://lore.kernel.org/r/1642432215-234089-4-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
John Garry [Mon, 17 Jan 2022 15:10:14 +0000 (23:10 +0800)]
perf test: Add pmu-events test for aliases with hyphens
Add a test for aliases with hyphens in the name to ensure that the
pmu-events tables are as expects. There should be no reason why these sort
of aliases would be treated differently, but no harm in checking.
Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qi Liu <liuqi115@huawei.com>
Cc: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: linuxarm@huawei.com
Link: https://lore.kernel.org/r/1642432215-234089-3-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
John Garry [Mon, 17 Jan 2022 15:10:13 +0000 (23:10 +0800)]
perf parse-events: Support event alias in form foo-bar-baz
Event aliasing for events whose name in the form foo-bar-baz is not
supported, while foo-bar, foo_bar_baz, and other combinations are, i.e.
two hyphens are not supported.
The HiSilicon D06 platform has events in such form:
$ ./perf list sdir-home-migrate
List of pre-defined events (to be used in -e):
uncore hha:
sdir-home-migrate
[Unit: hisi_sccl,hha]
$ sudo ./perf stat -e sdir-home-migrate
event syntax error: 'sdir-home-migrate'
\___ parser error
Run 'perf list' for a list of valid events
Usage: perf stat [<options>] [<command>]
-e, --event <event>event selector. use 'perf list' to list available events
To support, add an extra PMU event symbol type for "baz", and add a new
rule in the bison file.
Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qi Liu <liuqi115@huawei.com>
Cc: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: linuxarm@huawei.com
Link: https://lore.kernel.org/r/1642432215-234089-2-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
German Gomez [Tue, 18 Jan 2022 14:40:54 +0000 (14:40 +0000)]
perf evsel: Override attr->sample_period for non-libpfm4 events
A previous patch preventing "attr->sample_period" values from being
overridden in pfm events changed a related behaviour in arm-spe.
Before said patch:
perf record -c 10000 -e arm_spe_0// -- sleep 1
Would yield an SPE event with period=10000. After the patch, the period
in "-c 10000" was being ignored because the arm-spe code initializes
sample_period to a non-zero value.
This patch restores the previous behaviour for non-libpfm4 events.
Fixes:
ae5dcc8abe31 (“perf record: Prevent override of attr->sample_period for libpfm4 events”)
Reported-by: Chase Conklin <chase.conklin@arm.com>
Signed-off-by: German Gomez <german.gomez@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: KP Singh <kpsingh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: bpf@vger.kernel.org
Cc: netdev@vger.kernel.org
Link: http://lore.kernel.org/lkml/20220118144054.2541-1-german.gomez@arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Lv Ruyi [Mon, 17 Jan 2022 08:37:30 +0000 (08:37 +0000)]
perf cpumap: Remove duplicate include in cpumap.h
Remove all but the first include of stdbool.h from cpumap.h.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20220117083730.863200-1-lv.ruyi@zte.com.cn
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ian Rogers [Sat, 22 Jan 2022 04:58:10 +0000 (20:58 -0800)]
perf cpumap: Migrate to libperf cpumap api
Switch from directly accessing the perf_cpu_map to using the appropriate
libperf API when possible. Using the API simplifies the job of
refactoring use of perf_cpu_map.
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Bayduraev <alexey.v.bayduraev@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: André Almeida <andrealmeid@collabora.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: German Gomez <german.gomez@arm.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Miaoqian Lin <linmq006@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Riccardo Mancini <rickyman7@gmail.com>
Cc: Shunsuke Nakamura <nakamura.shun@fujitsu.com>
Cc: Song Liu <song@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Stephen Brennan <stephen.s.brennan@oracle.com>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Yury Norov <yury.norov@gmail.com>
Link: http://lore.kernel.org/lkml/20220122045811.3402706-3-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ian Rogers [Sat, 22 Jan 2022 04:58:09 +0000 (20:58 -0800)]
perf python: Fix cpu_map__item() building
Value should be built as an integer.
Switch some uses of perf_cpu_map to use the library API.
Fixes:
6d18804b963b78dc ("perf cpumap: Give CPUs their own type")
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Bayduraev <alexey.v.bayduraev@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: André Almeida <andrealmeid@collabora.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: German Gomez <german.gomez@arm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Miaoqian Lin <linmq006@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Riccardo Mancini <rickyman7@gmail.com>
Cc: Shunsuke Nakamura <nakamura.shun@fujitsu.com>
Cc: Song Liu <song@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Stephen Brennan <stephen.s.brennan@oracle.com>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Yury Norov <yury.norov@gmail.com>
Link: http://lore.kernel.org/lkml/20220122045811.3402706-2-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Yao Jin [Fri, 21 Jan 2022 06:59:54 +0000 (14:59 +0800)]
perf script: Fix printing 'phys_addr' failure issue
Perf script was failed to print the phys_addr for SPE profiling.
One 'dummy' event is added by SPE profiling but it doesn't have PHYS_ADDR
attribute set, perf script then exits with error.
Now referring to 'addr', use evsel__do_check_stype() to check the type.
Before:
# perf record -e arm_spe_0/branch_filter=0,ts_enable=1,pa_enable=1,load_filter=1,jitter=0,\
store_filter=0,min_latency=0,event_filter=2/ -p
4064384 -- sleep 3
# perf script -F pid,tid,addr,phys_addr
Samples for 'dummy:u' event do not have PHYS_ADDR attribute set. Cannot print 'phys_addr' field.
After:
# perf record -e arm_spe_0/branch_filter=0,ts_enable=1,pa_enable=1,load_filter=1,jitter=0,\
store_filter=0,min_latency=0,event_filter=2/ -p
4064384 -- sleep 3
# perf script -F pid,tid,addr,phys_addr
4064384/
4064384 ffff802f921be0d0 2f921be0d0
4064384/
4064384 ffff802f921be0d0 2f921be0d0
Reviewed-by: German Gomez <german.gomez@arm.com>
Signed-off-by: Yao Jin <jinyao5@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20220121065954.2121900-1-liwei391@huawei.com
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Masahiro Yamada [Thu, 20 Jan 2022 19:22:05 +0000 (04:22 +0900)]
certs: Fix build error when CONFIG_MODULE_SIG_KEY is empty
Since
b8c96a6b466c ("certs: simplify $(srctree)/ handling and remove
config_filename macro"), when CONFIG_MODULE_SIG_KEY is empty,
signing_key.x509 fails to build:
CERT certs/signing_key.x509
Usage: extract-cert <source> <dest>
make[1]: *** [certs/Makefile:78: certs/signing_key.x509] Error 2
make: *** [Makefile:1831: certs] Error 2
Pass "" to the first argument of extract-cert to fix the build error.
Link: https://lore.kernel.org/linux-kbuild/20220120094606.2skuyb26yjlnu66q@lion.mk-sys.cz/T/#u
Fixes:
b8c96a6b466c ("certs: simplify $(srctree)/ handling and remove config_filename macro")
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Michal Kubecek <mkubecek@suse.cz>
Masahiro Yamada [Thu, 20 Jan 2022 19:22:04 +0000 (04:22 +0900)]
certs: Fix build error when CONFIG_MODULE_SIG_KEY is PKCS#11 URI
When CONFIG_MODULE_SIG_KEY is PKCS#11 URL (pkcs11:*), signing_key.x509
fails to build:
certs/Makefile:77: *** target pattern contains no '%'. Stop.
Due to the typo, $(X509_DEP) contains a colon.
Fix it.
Fixes:
b8c96a6b466c ("certs: simplify $(srctree)/ handling and remove config_filename macro")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Masahiro Yamada [Thu, 20 Jan 2022 05:31:00 +0000 (14:31 +0900)]
Revert "Makefile: Do not quote value for CONFIG_CC_IMPLICIT_FALLTHROUGH"
This reverts commit
cd8c917a56f20f48748dd43d9ae3caff51d5b987.
Commit
129ab0d2d9f3 ("kbuild: do not quote string values in
include/config/auto.conf") provided the final solution.
Now reverting the temporary workaround.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Dmitry V. Levin [Mon, 3 Jan 2022 01:24:02 +0000 (04:24 +0300)]
usr/include/Makefile: add linux/nfc.h to the compile-test coverage
As linux/nfc.h userspace compilation was finally fixed by commits
79b69a83705e ("nfc: uapi: use kernel size_t to fix user-space builds")
and
7175f02c4e5f ("uapi: fix linux/nfc.h userspace compilation errors"),
there is no need to keep the compile-test exception for it in
usr/include/Makefile.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Linus Torvalds [Sat, 22 Jan 2022 09:28:23 +0000 (11:28 +0200)]
Merge branch 'akpm' (patches from Andrew)
Merge yet more updates from Andrew Morton:
"This is the post-linux-next queue. Material which was based on or
dependent upon material which was in -next.
69 patches.
Subsystems affected by this patch series: mm (migration and zsmalloc),
sysctl, proc, and lib"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (69 commits)
mm: hide the FRONTSWAP Kconfig symbol
frontswap: remove support for multiple ops
mm: mark swap_lock and swap_active_head static
frontswap: simplify frontswap_register_ops
frontswap: remove frontswap_test
mm: simplify try_to_unuse
frontswap: remove the frontswap exports
frontswap: simplify frontswap_init
frontswap: remove frontswap_curr_pages
frontswap: remove frontswap_shrink
frontswap: remove frontswap_tmem_exclusive_gets
frontswap: remove frontswap_writethrough
mm: remove cleancache
lib/stackdepot: always do filter_irq_stacks() in stack_depot_save()
lib/stackdepot: allow optional init and stack_table allocation by kvmalloc()
proc: remove PDE_DATA() completely
fs: proc: store PDE()->data into inode->i_private
zsmalloc: replace get_cpu_var with local_lock
zsmalloc: replace per zpage lock with pool->migrate_lock
locking/rwlocks: introduce write_lock_nested
...
Linus Torvalds [Sat, 22 Jan 2022 09:12:26 +0000 (11:12 +0200)]
Merge tag '5.17-rc-part2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
- multichannel fixes, addressing additional reconnect and DFS scenarios
- reenabling fscache support (indexing rewrite, metadata caching e.g.)
- send additional version information during NTLMSSP negotiate to
improve debugging
- fix for a mount race
- DFS fixes
- fix for a memory leak for stable
* tag '5.17-rc-part2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module number
smb3: send NTLMSSP version information
cifs: Support fscache indexing rewrite
cifs: cifs_ses_mark_for_reconnect should also update reconnect bits
cifs: update tcpStatus during negotiate and sess setup
cifs: make status checks in version independent callers
cifs: remove repeated state change in dfs tree connect
cifs: fix the cifs_reconnect path for DFS
cifs: remove unused variable ses_selected
cifs: protect all accesses to chan_* with chan_lock
cifs: fix the connection state transitions with multichannel
cifs: check reconnects for channels of active tcons too
smb3: add new defines from protocol specification
cifs: serialize all mount attempts
cifs: quirk for STATUS_OBJECT_NAME_INVALID returned for non-ASCII dfs refs
cifs: alloc_path_with_tree_prefix: do not append sep. if the path is empty
cifs: clean up an inconsistent indenting
cifs: free ntlmsspblob allocated in negotiate
Linus Torvalds [Sat, 22 Jan 2022 09:04:27 +0000 (11:04 +0200)]
Merge tag 'xfs-5.17-merge-7' of git://git./fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"One of the patches removes some dead code from xfs_ioctl32.h and the
other fixes broken workqueue flushing in the inode garbage collector.
- Minor cleanup of ioctl32 cruft
- Clean up open coded inodegc workqueue function calls"
* tag 'xfs-5.17-merge-7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: flush inodegc workqueue tasks before cancel
xfs: remove unused xfs_ioctl32.h declarations
Linus Torvalds [Sat, 22 Jan 2022 08:59:32 +0000 (10:59 +0200)]
Merge tag 'fscache-fixes-
20220121' of git://git./linux/kernel/git/dhowells/linux-fs
Pull more fscache updates from David Howells:
"A set of fixes and minor updates for the fscache rewrite:
- Fix mishandling of volume collisions (the wait condition is
inverted and so it was only waiting if the volume collision was
already resolved).
- Fix miscalculation of whether there's space available in
cachefiles.
- Make sure a default cache name is set on a cache if the user hasn't
set one by the time they bind the cache.
- Adjust the way the backing inode is presented in tracepoints, add a
tracepoint for mkdir and trace directory lookup.
- Add a tracepoint for failure to set the active file mark.
- Add an explanation of the checks made on the backing filesystem.
- Check that the backing filesystem supports tmpfile.
- Document how the page-release cancellation of the read-skip
optimisation works.
And I've included a change for netfslib:
- Make ops->init_rreq() optional"
* tag 'fscache-fixes-
20220121' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
netfs: Make ops->init_rreq() optional
fscache: Add a comment explaining how page-release optimisation works
cachefiles: Check that the backing filesystem supports tmpfiles
cachefiles: Explain checks in a comment
cachefiles: Trace active-mark failure
cachefiles: Make some tracepoint adjustments
cachefiles: set default tag name if it's unspecified
cachefiles: Calculate the blockshift in terms of bytes, not pages
fscache: Fix the volume collision wait condition
Linus Torvalds [Sat, 22 Jan 2022 08:43:07 +0000 (10:43 +0200)]
Merge tag 'folio-5.17a' of git://git.infradead.org/users/willy/pagecache
Pull more folio updates from Matthew Wilcox:
"Three small folio patches.
One bug fix, one patch pulled forward from the patches destined for
5.18 and then a patch to make use of that functionality"
* tag 'folio-5.17a' of git://git.infradead.org/users/willy/pagecache:
filemap: Use folio_put_refs() in filemap_free_folio()
mm: Add folio_put_refs()
pagevec: Initialise folio_batch->percpu_pvec_drained
Linus Torvalds [Sat, 22 Jan 2022 08:24:02 +0000 (10:24 +0200)]
Merge tag 'scsi-misc' of git://git./linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This series is all the stragglers that didn't quite make the first
merge window pull. It's mostly minor updates and bug fixes of merge
window code"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: nsp_cs: Check of ioremap return value
scsi: ufs: ufs-mediatek: Fix error checking in ufs_mtk_init_va09_pwr_ctrl()
scsi: ufs: Modify Tactive time setting conditions
scsi: efct: Remove useless DMA-32 fallback configuration
scsi: message: fusion: mptctl: Use dma_alloc_coherent()
scsi: message: fusion: mptsas: Use dma_alloc_coherent()
scsi: message: fusion: Use dma_alloc_coherent() in mptsas_exp_repmanufacture_info()
scsi: message: fusion: mptbase: Use dma_alloc_coherent()
scsi: message: fusion: Use dma_alloc_coherent() in mpt_alloc_fw_memory()
scsi: message: fusion: Remove usage of the deprecated "pci-dma-compat.h" API
scsi: megaraid: Avoid mismatched storage type sizes
scsi: hisi_sas: Remove unused variable and check in hisi_sas_send_ata_reset_each_phy()
scsi: aic79xx: Remove redundant error variable
scsi: pm80xx: Port reset timeout error handling correction
scsi: mpi3mr: Fix formatting problems in some kernel-doc comments
scsi: mpi3mr: Fix some spelling mistakes
scsi: mpt3sas: Update persistent trigger pages from sysfs interface
scsi: core: Fix scsi_mode_select() interface
scsi: aacraid: Fix spelling of "its"
scsi: qedf: Fix potential dereference of NULL pointer
Linus Torvalds [Sat, 22 Jan 2022 08:22:11 +0000 (10:22 +0200)]
Merge tag 'ata-5.17-rc1-part2' of git://git./linux/kernel/git/dlemoal/libata
Pull ATA fix from Damien Le Moal:
"A single patch to fix a compilation error in the pata_octeon_cf driver
(mips architecture), from me"
* tag 'ata-5.17-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: pata_octeon_cf: fix call to trace_ata_bmdma_stop()
Linus Torvalds [Sat, 22 Jan 2022 08:15:41 +0000 (10:15 +0200)]
Merge tag 'thermal-5.17-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm
Pull more thermal control updates from Rafael Wysocki:
"Add device IDs for Raptor Lake to the int340x thermal control driver
(Srinivas Pandruvada)"
* tag 'thermal-5.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: int340x: Add Raptor Lake PCI device id
thermal: int340x: Support Raptor Lake
Linus Torvalds [Sat, 22 Jan 2022 08:09:51 +0000 (10:09 +0200)]
Merge tag 'acpi-5.17-rc1-3' of git://git./linux/kernel/git/rafael/linux-pm
Pull extra ACPI updates from Rafael Wysocki:
"These fix and clean up the ACPI CPPC driver on top of the recent
changes in it merged previously and add some new device IDs to the
ACPI DPTF driver.
Specifics:
- Fix a recently introduced endianness-related issue in the ACPI CPPC
library and clean it up on top of that (Rafael Wysocki)
- Add new device IDs for the Raptor Lake SoC to the ACPI DPTF driver
(Srinivas Pandruvada)"
* tag 'acpi-5.17-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: DPTF: Support Raptor Lake
ACPI: CPPC: Drop redundant local variable from cpc_read()
ACPI: CPPC: Fix up I/O port access in cpc_read()
Linus Torvalds [Sat, 22 Jan 2022 07:52:17 +0000 (09:52 +0200)]
Merge tag 'devicetree-fixes-for-5.17-1' of git://git./linux/kernel/git/robh/linux
Pull devicetree fixes and cleanups from Rob Herring:
- Fix a regression when probing a child device reusing the parent
device's DT node pointer
- Refactor of_parse_phandle*() variants to static inlines
- Drop Enric Balletbo i Serra as a maintainer
- Fix DT schemas with arrays incorrectly encoded as a matrix
- Drop unneeded pinctrl properties from schemas
- Add SPI peripheral schema to SPI based displays
- Clean-up several schema examples
- Clean-up trivial-devices.yaml comments
- Add missing, in use vendor prefixes: Wingtech, Thundercomm, Huawei,
F(x)tec, 8devices
* tag 'devicetree-fixes-for-5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: google,cros-ec: drop Enric Balletbo i Serra from maintainers
dt-bindings: display: bridge: drop Enric Balletbo i Serra from maintainers
of: Check 'of_node_reused' flag on of_match_device()
of: property: define of_property_read_u{8,16,32,64}_array() unconditionally
of: base: make small of_parse_phandle() variants static inline
dt-bindings: mfd: cirrus,madera: Fix 'interrupts' in example
dt-bindings: Fix array schemas encoded as matrices
dt-bindings: Drop unnecessary pinctrl properties
dt-bindings: rtc: st,stm32-rtc: Make each example a separate entry
dt-bindings: mmc: arm,pl18x: Make each example a separate entry
dt-bindings: display: Add SPI peripheral schema to SPI based displays
scripts/dtc: dtx_diff: remove broken example from help text
dt-bindings: trivial-devices: fix double spaces in comments
dt-bindings: trivial-devices: fix swapped comments
dt-bindings: vendor-prefixes: add Wingtech
dt-bindings: vendor-prefixes: add Thundercomm
dt-bindings: vendor-prefixes: add Huawei
dt-bindings: vendor-prefixes: add F(x)tec
dt-bindings: vendor-prefixes: add 8devices
dt-bindings: power: reset: gpio-restart: Correct default priority
Linus Torvalds [Sat, 22 Jan 2022 07:40:01 +0000 (09:40 +0200)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull more kvm updates from Paolo Bonzini:
"Generic:
- selftest compilation fix for non-x86
- KVM: avoid warning on s390 in mark_page_dirty
x86:
- fix page write-protection bug and improve comments
- use binary search to lookup the PMU event filter, add test
- enable_pmu module parameter support for Intel CPUs
- switch blocked_vcpu_on_cpu_lock to raw spinlock
- cleanups of blocked vCPU logic
- partially allow KVM_SET_CPUID{,2} after KVM_RUN (5.16 regression)
- various small fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (46 commits)
docs: kvm: fix WARNINGs from api.rst
selftests: kvm/x86: Fix the warning in lib/x86_64/processor.c
selftests: kvm/x86: Fix the warning in pmu_event_filter_test.c
kvm: selftests: Do not indent with spaces
kvm: selftests: sync uapi/linux/kvm.h with Linux header
selftests: kvm: add amx_test to .gitignore
KVM: SVM: Nullify vcpu_(un)blocking() hooks if AVIC is disabled
KVM: SVM: Move svm_hardware_setup() and its helpers below svm_x86_ops
KVM: SVM: Drop AVIC's intermediate avic_set_running() helper
KVM: VMX: Don't do full kick when handling posted interrupt wakeup
KVM: VMX: Fold fallback path into triggering posted IRQ helper
KVM: VMX: Pass desired vector instead of bool for triggering posted IRQ
KVM: VMX: Don't do full kick when triggering posted interrupt "fails"
KVM: SVM: Skip AVIC and IRTE updates when loading blocking vCPU
KVM: SVM: Use kvm_vcpu_is_blocking() in AVIC load to handle preemption
KVM: SVM: Remove unnecessary APICv/AVIC update in vCPU unblocking path
KVM: SVM: Don't bother checking for "running" AVIC when kicking for IPIs
KVM: SVM: Signal AVIC doorbell iff vCPU is in guest mode
KVM: x86: Remove defunct pre_block/post_block kvm_x86_ops hooks
KVM: x86: Unexport LAPIC's switch_to_{hv,sw}_timer() helpers
...
Linus Torvalds [Sat, 22 Jan 2022 07:37:31 +0000 (09:37 +0200)]
Merge tag 'for-5.17/parisc-2' of git://git./linux/kernel/git/deller/parisc-linux
Pull more parisc architecture updates from Helge Deller:
"Fixes and enhancements:
- a memory leak fix in an error path in pdc_stable (Miaoqian Lin)
- two compiler warning fixes in the TOC code
- added autodetection for currently used console type (serial or
graphics) which inserts console=<type> if it's missing"
* tag 'for-5.17/parisc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: pdc_stable: Fix memory leak in pdcs_register_pathentries
parisc: Fix missing prototype for 'toc_intr' warning in toc.c
parisc: Autodetect default output device and set console= kernel parameter
parisc: Use safer strscpy() in setup_cmdline()
parisc: Add visible flag to toc_stack variable
Linus Torvalds [Sat, 22 Jan 2022 07:34:49 +0000 (09:34 +0200)]
Merge tag 'riscv-for-linus-5.17-mw1' of git://git./linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
- Support for sv48 paging
- Hart ID mappings are now sparse, which enables more CPUs to come up
on systems with sparse hart IDs
- A handful of cleanups and fixes
* tag 'riscv-for-linus-5.17-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (27 commits)
RISC-V: nommu_virt: Drop unused SLAB_MERGE_DEFAULT
RISC-V: Remove redundant err variable
riscv: dts: sifive unmatched: Add gpio poweroff
riscv: canaan: remove useless select of non-existing config SYSCON
RISC-V: Do not use cpumask data structure for hartid bitmap
RISC-V: Move spinwait booting method to its own config
RISC-V: Move the entire hart selection via lottery to SMP
RISC-V: Use __cpu_up_stack/task_pointer only for spinwait method
RISC-V: Do not print the SBI version during HSM extension boot print
RISC-V: Avoid using per cpu array for ordered booting
riscv: default to CONFIG_RISCV_SBI_V01=n
riscv: fix boolconv.cocci warnings
riscv: Explicit comment about user virtual address space size
riscv: Use pgtable_l4_enabled to output mmu_type in cpuinfo
riscv: Implement sv48 support
asm-generic: Prepare for riscv use of pud_alloc_one and pud_free
riscv: Allow to dynamically define VA_BITS
riscv: Introduce functions to switch pt_ops
riscv: Split early kasan mapping to prepare sv48 introduction
riscv: Move KASAN mapping next to the kernel mapping
...
Linus Torvalds [Sat, 22 Jan 2022 07:22:10 +0000 (09:22 +0200)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes/cleanups from Catalin Marinas:
"Some fixes that turned up during the merge window:
- Add brackets to the io_stop_wc macro
- Avoid -Warray-bounds warning with the LSE atomics inline asm
- Apply __ro_after_init to memory_limit"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: apply __ro_after_init to memory_limit
arm64: atomics: lse: Dereference matching size
asm-generic: Add missing brackets for io_stop_wc macro
Linus Torvalds [Sat, 22 Jan 2022 07:02:57 +0000 (09:02 +0200)]
Merge tag 'docs-5.17-2' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"Three small documentation fixes"
* tag 'docs-5.17-2' of git://git.lwn.net/linux:
Documentation: fix firewire.rst ABI file path error
docs: ftrace: fix ambiguous sentence
docs: staging/tee.rst: fix two typos found while reading
Christoph Hellwig [Sat, 22 Jan 2022 06:15:14 +0000 (22:15 -0800)]
mm: hide the FRONTSWAP Kconfig symbol
Select FRONTSWAP from ZSWAP instead of prompting for it.
Link: https://lkml.kernel.org/r/20211224062246.1258487-14-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Sat, 22 Jan 2022 06:15:10 +0000 (22:15 -0800)]
frontswap: remove support for multiple ops
There is only a single instance of frontswap ops in the kernel, so
simplify the frontswap code by removing support for multiple operations.
Link: https://lkml.kernel.org/r/20211224062246.1258487-13-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Sat, 22 Jan 2022 06:15:07 +0000 (22:15 -0800)]
mm: mark swap_lock and swap_active_head static
swap_lock and swap_active_head are only used in swapfile.c, so mark them
static.
Link: https://lkml.kernel.org/r/20211224062246.1258487-12-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Sat, 22 Jan 2022 06:15:04 +0000 (22:15 -0800)]
frontswap: simplify frontswap_register_ops
Given that frontswap_register_ops must be called from built-in code,
there is no need to handle the case of swapfiles coming online before or
during it, so delete the code that deals with that case.
Link: https://lkml.kernel.org/r/20211224062246.1258487-11-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Sat, 22 Jan 2022 06:15:01 +0000 (22:15 -0800)]
frontswap: remove frontswap_test
frontswap_test is unused now, remove it.
Link: https://lkml.kernel.org/r/20211224062246.1258487-10-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Sat, 22 Jan 2022 06:14:57 +0000 (22:14 -0800)]
mm: simplify try_to_unuse
Remove the unused frontswap and pages_to_unuse arguments, and mark the
function static now that the caller in frontswap is gone.
[akpm@linux-foundation.org: fix shmem_unuse() stub, per Matthew]
Link: https://lkml.kernel.org/r/20211224062246.1258487-9-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Sat, 22 Jan 2022 06:14:54 +0000 (22:14 -0800)]
frontswap: remove the frontswap exports
None of the frontswap API is called from modular code.
Link: https://lkml.kernel.org/r/20211224062246.1258487-8-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Sat, 22 Jan 2022 06:14:51 +0000 (22:14 -0800)]
frontswap: simplify frontswap_init
Just use IS_ENABLED() and remove the __frontswap_init indirection.
Also remove the unused export.
Link: https://lkml.kernel.org/r/20211224062246.1258487-7-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Sat, 22 Jan 2022 06:14:47 +0000 (22:14 -0800)]
frontswap: remove frontswap_curr_pages
frontswap_curr_pages is never called, so remove it.
Link: https://lkml.kernel.org/r/20211224062246.1258487-6-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Sat, 22 Jan 2022 06:14:44 +0000 (22:14 -0800)]
frontswap: remove frontswap_shrink
frontswap_shrink is never called, so remove it.
Link: https://lkml.kernel.org/r/20211224062246.1258487-5-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Sat, 22 Jan 2022 06:14:41 +0000 (22:14 -0800)]
frontswap: remove frontswap_tmem_exclusive_gets
frontswap_tmem_exclusive_gets is never called, so remove it.
Link: https://lkml.kernel.org/r/20211224062246.1258487-4-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Sat, 22 Jan 2022 06:14:38 +0000 (22:14 -0800)]
frontswap: remove frontswap_writethrough
frontswap_writethrough is never called, so remove it.
Link: https://lkml.kernel.org/r/20211224062246.1258487-3-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Sat, 22 Jan 2022 06:14:34 +0000 (22:14 -0800)]
mm: remove cleancache
Patch series "remove Xen tmem leftovers".
Since the removal of the Xen tmem driver in 2019, the cleancache hooks
are entirely unused, as are large parts of frontswap. This series
against linux-next (with the folio changes included) removes
cleancaches, and cuts down frontswap to the bits actually used by zswap.
This patch (of 13):
The cleancache subsystem is unused since the removal of Xen tmem driver
in commit
814bbf49dcd0 ("xen: remove tmem driver").
[akpm@linux-foundation.org: remove now-unreachable code]
Link: https://lkml.kernel.org/r/20211224062246.1258487-1-hch@lst.de
Link: https://lkml.kernel.org/r/20211224062246.1258487-2-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marco Elver [Sat, 22 Jan 2022 06:14:31 +0000 (22:14 -0800)]
lib/stackdepot: always do filter_irq_stacks() in stack_depot_save()
The non-interrupt portion of interrupt stack traces before interrupt
entry is usually arbitrary. Therefore, saving stack traces of
interrupts (that include entries before interrupt entry) to stack depot
leads to unbounded stackdepot growth.
As such, use of filter_irq_stacks() is a requirement to ensure
stackdepot can efficiently deduplicate interrupt stacks.
Looking through all current users of stack_depot_save(), none (except
KASAN) pass the stack trace through filter_irq_stacks() before passing
it on to stack_depot_save().
Rather than adding filter_irq_stacks() to all current users of
stack_depot_save(), it became clear that stack_depot_save() should
simply do filter_irq_stacks().
Link: https://lkml.kernel.org/r/20211130095727.2378739-1-elver@google.com
Signed-off-by: Marco Elver <elver@google.com>
Reviewed-by: Alexander Potapenko <glider@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Vijayanand Jitta <vjitta@codeaurora.org>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Imran Khan <imran.f.khan@oracle.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vlastimil Babka [Sat, 22 Jan 2022 06:14:27 +0000 (22:14 -0800)]
lib/stackdepot: allow optional init and stack_table allocation by kvmalloc()
Currently, enabling CONFIG_STACKDEPOT means its stack_table will be
allocated from memblock, even if stack depot ends up not actually used.
The default size of stack_table is 4MB on 32-bit, 8MB on 64-bit.
This is fine for use-cases such as KASAN which is also a config option
and has overhead on its own. But it's an issue for functionality that
has to be actually enabled on boot (page_owner) or depends on hardware
(GPU drivers) and thus the memory might be wasted. This was raised as
an issue [1] when attempting to add stackdepot support for SLUB's debug
object tracking functionality. It's common to build kernels with
CONFIG_SLUB_DEBUG and enable slub_debug on boot only when needed, or
create only specific kmem caches with debugging for testing purposes.
It would thus be more efficient if stackdepot's table was allocated only
when actually going to be used. This patch thus makes the allocation
(and whole stack_depot_init() call) optional:
- Add a CONFIG_STACKDEPOT_ALWAYS_INIT flag to keep using the current
well-defined point of allocation as part of mem_init(). Make
CONFIG_KASAN select this flag.
- Other users have to call stack_depot_init() as part of their own init
when it's determined that stack depot will actually be used. This may
depend on both config and runtime conditions. Convert current users
which are page_owner and several in the DRM subsystem. Same will be
done for SLUB later.
- Because the init might now be called after the boot-time memblock
allocation has given all memory to the buddy allocator, change
stack_depot_init() to allocate stack_table with kvmalloc() when
memblock is no longer available. Also handle allocation failure by
disabling stackdepot (could have theoretically happened even with
memblock allocation previously), and don't unnecessarily align the
memblock allocation to its own size anymore.
[1] https://lore.kernel.org/all/CAMuHMdW=eoVzM1Re5FVoEN87nKfiLmM2+Ah7eNu2KXEhCvbZyA@mail.gmail.com/
Link: https://lkml.kernel.org/r/20211013073005.11351-1-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Marco Elver <elver@google.com> # stackdepot
Cc: Marco Elver <elver@google.com>
Cc: Vijayanand Jitta <vjitta@codeaurora.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Oliver Glitta <glittao@gmail.com>
Cc: Imran Khan <imran.f.khan@oracle.com>
From: Colin Ian King <colin.king@canonical.com>
Subject: lib/stackdepot: fix spelling mistake and grammar in pr_err message
There is a spelling mistake of the work allocation so fix this and
re-phrase the message to make it easier to read.
Link: https://lkml.kernel.org/r/20211015104159.11282-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
From: Vlastimil Babka <vbabka@suse.cz>
Subject: lib/stackdepot: allow optional init and stack_table allocation by kvmalloc() - fixup
On FLATMEM, we call page_ext_init_flatmem_late() just before
kmem_cache_init() which means stack_depot_init() (called by page owner
init) will not recognize properly it should use kvmalloc() and not
memblock_alloc(). memblock_alloc() will also not issue a warning and
return a block memory that can be invalid and cause kernel page fault when
saving stacks, as reported by the kernel test robot [1].
Fix this by moving page_ext_init_flatmem_late() below kmem_cache_init() so
that slab_is_available() is true during stack_depot_init(). SPARSEMEM
doesn't have this issue, as it doesn't do page_ext_init_flatmem_late(),
but a different page_ext_init() even later in the boot process.
Thanks to Mike Rapoport for pointing out the FLATMEM init ordering issue.
While at it, also actually resolve a checkpatch warning in stack_depot_init()
from DRM CI, which was supposed to be in the original patch already.
[1] https://lore.kernel.org/all/
20211014085450.GC18719@xsang-OptiPlex-9020/
Link: https://lkml.kernel.org/r/6abd9213-19a9-6d58-cedc-2414386d2d81@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: kernel test robot <oliver.sang@intel.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
From: Vlastimil Babka <vbabka@suse.cz>
Subject: lib/stackdepot: allow optional init and stack_table allocation by kvmalloc() - fixup3
Due to
cd06ab2fd48f ("drm/locking: add backtrace for locking contended
locks without backoff") landing recently to -next adding a new stack depot
user in drivers/gpu/drm/drm_modeset_lock.c we need to add an appropriate
call to stack_depot_init() there as well.
Link: https://lkml.kernel.org/r/2a692365-cfa1-64f2-34e0-8aa5674dce5e@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Marco Elver <elver@google.com>
Cc: Vijayanand Jitta <vjitta@codeaurora.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Oliver Glitta <glittao@gmail.com>
Cc: Imran Khan <imran.f.khan@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
From: Vlastimil Babka <vbabka@suse.cz>
Subject: lib/stackdepot: allow optional init and stack_table allocation by kvmalloc() - fixup4
Due to
4e66934eaadc ("lib: add reference counting tracking
infrastructure") landing recently to net-next adding a new stack depot
user in lib/ref_tracker.c we need to add an appropriate call to
stack_depot_init() there as well.
Link: https://lkml.kernel.org/r/45c1b738-1a2f-5b5f-2f6d-86fab206d01c@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Slab <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>