OSDN Git Service
Casey Leedom [Tue, 15 Aug 2017 03:23:26 +0000 (11:23 +0800)]
net/cxgb4: Use new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag
cxgb4 Ethernet driver now queries PCIe configuration space to determine
if it can send TLPs to it with the Relaxed Ordering Attribute set.
Remove the enable_pcie_relaxed_ordering() to avoid enable PCIe Capability
Device Control[Relaxed Ordering Enable] at probe routine, to make sure
the driver will not send the Relaxed Ordering TLPs to the Root Complex which
could not deal the Relaxed Ordering TLPs.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dingtianhong [Tue, 15 Aug 2017 03:23:25 +0000 (11:23 +0800)]
PCI: Disable Relaxed Ordering Attributes for AMD A1100
Casey reported that the AMD ARM A1100 SoC has a bug in its PCIe
Root Port where Upstream Transaction Layer Packets with the Relaxed
Ordering Attribute clear are allowed to bypass earlier TLPs with
Relaxed Ordering set, it would cause Data Corruption, so we need
to disable Relaxed Ordering Attribute when Upstream TLPs to the
Root Port.
Reported-and-suggested-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dingtianhong [Tue, 15 Aug 2017 03:23:24 +0000 (11:23 +0800)]
PCI: Disable Relaxed Ordering for some Intel processors
According to the Intel spec section 3.9.1 said:
3.9.1 Optimizing PCIe Performance for Accesses Toward Coherent Memory
and Toward MMIO Regions (P2P)
In order to maximize performance for PCIe devices in the processors
listed in Table 3-6 below, the soft- ware should determine whether the
accesses are toward coherent memory (system memory) or toward MMIO
regions (P2P access to other devices). If the access is toward MMIO
region, then software can command HW to set the RO bit in the TLP
header, as this would allow hardware to achieve maximum throughput for
these types of accesses. For accesses toward coherent memory, software
can command HW to clear the RO bit in the TLP header (no RO), as this
would allow hardware to achieve maximum throughput for these types of
accesses.
Table 3-6. Intel Processor CPU RP Device IDs for Processors Optimizing
PCIe Performance
Processor CPU RP Device IDs
Intel Xeon processors based on 6F01H-6F0EH
Broadwell microarchitecture
Intel Xeon processors based on 2F01H-2F0EH
Haswell microarchitecture
It means some Intel processors has performance issue when use the Relaxed
Ordering Attribute, so disable Relaxed Ordering for these root port.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dingtianhong [Tue, 15 Aug 2017 03:23:23 +0000 (11:23 +0800)]
PCI: Disable PCIe Relaxed Ordering if unsupported
When bit4 is set in the PCIe Device Control register, it indicates
whether the device is permitted to use relaxed ordering.
On some platforms using relaxed ordering can have performance issues or
due to erratum can cause data-corruption. In such cases devices must avoid
using relaxed ordering.
The patch adds a new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING to indicate that
Relaxed Ordering (RO) attribute should not be used for Transaction Layer
Packets (TLP) targeted towards these affected root complexes.
This patch checks if there is any node in the hierarchy that indicates that
using relaxed ordering is not safe. In such cases the patch turns off the
relaxed ordering by clearing the capability for this device.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Mon, 14 Aug 2017 16:28:49 +0000 (18:28 +0200)]
tipc: avoid inheriting msg_non_seq flag when message is returned
In the function msg_reverse(), we reverse the header while trying to
reuse the original buffer whenever possible. Those rejected/returned
messages are always transmitted as unicast, but the msg_non_seq field
is not explicitly set to zero as it should be.
We have seen cases where multicast senders set the message type to
"NOT dest_droppable", meaning that a multicast message shorter than
one MTU will be returned, e.g., during receive buffer overflow, by
reusing the original buffer. This has the effect that even the
'msg_non_seq' field is inadvertently inherited by the rejected message,
although it is now sent as a unicast message. This again leads the
receiving unicast link endpoint to steer the packet toward the broadcast
link receive function, where it is dropped. The affected unicast link is
thereafter (after 100 failed retransmissions) declared 'stale' and
reset.
We fix this by unconditionally setting the 'msg_non_seq' flag to zero
for all rejected/returned messages.
Reported-by: Canh Duc Luu <canh.d.luu@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Mon, 14 Aug 2017 15:55:56 +0000 (17:55 +0200)]
tipc: accept PACKET_MULTICAST packets
On L2 bearers, the TIPC broadcast function is sending out packets using
the corresponding L2 broadcast address. At reception, we filter such
packets under the assumption that they will also be delivered as
broadcast packets.
This assumption doesn't always hold true. Under high load, we have seen
that a switch may convert the destination address and deliver the packet
as a PACKET_MULTICAST, something leading to inadvertently dropped
packets and a stale and reset broadcast link.
We fix this by extending the reception filtering to accept packets of
type PACKET_MULTICAST.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Sun, 13 Aug 2017 22:52:58 +0000 (00:52 +0200)]
ipv4: route: fix inet_rtm_getroute induced crash
"ip route get $daddr iif eth0 from $saddr" causes:
BUG: KASAN: use-after-free in ip_route_input_rcu+0x1535/0x1b50
Call Trace:
ip_route_input_rcu+0x1535/0x1b50
ip_route_input_noref+0xf9/0x190
tcp_v4_early_demux+0x1a4/0x2b0
ip_rcv+0xbcb/0xc05
__netif_receive_skb+0x9c/0xd0
netif_receive_skb_internal+0x5a8/0x890
Problem is that inet_rtm_getroute calls either ip_route_input_rcu (if an
iif was provided) or ip_route_output_key_hash_rcu.
But ip_route_input_rcu, unlike ip_route_output_key_hash_rcu, already
associates the dst_entry with the skb. This clears the SKB_DST_NOREF
bit (i.e. skb_dst_drop will release/free the entry while it should not).
Thus only set the dst if we called ip_route_output_key_hash_rcu().
I tested this patch by running:
while true;do ip r get 10.0.1.2;done > /dev/null &
while true;do ip r get 10.0.1.2 iif eth0 from 10.0.1.1;done > /dev/null &
... and saw no crash or memory leak.
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: David Ahern <dsahern@gmail.com>
Fixes:
ba52d61e0ff ("ipv4: route: restore skb_dst_set in inet_rtm_getroute")
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Born [Fri, 11 Aug 2017 22:36:55 +0000 (00:36 +0200)]
bonding: ratelimit failed speed/duplex update warning
bond_miimon_commit() handles the UP transition for each slave of a bond
in the case of MII. It is triggered 10 times per second for the default
MII Polling interval of 100ms. For device drivers that do not implement
__ethtool_get_link_ksettings() the call to bond_update_speed_duplex()
fails persistently while the MII status could remain UP. That is, in
this and other cases where the speed/duplex update keeps failing over a
longer period of time while the MII state is UP, a warning is printed
every MII polling interval.
To address these excessive warnings net_ratelimit() should be used.
Printing a warning once would not be sufficient since the call to
bond_update_speed_duplex() could recover to succeed and fail again
later. In that case there would be no new indication what went wrong.
Fixes:
b5bf0f5b16b9c (bonding: correctly update link status during mii-commit phase)
Signed-off-by: Andreas Born <futur.andy@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 11 Aug 2017 17:48:53 +0000 (10:48 -0700)]
udp: harden copy_linear_skb()
syzkaller got crashes with CONFIG_HARDENED_USERCOPY=y configs.
Issue here is that recvfrom() can be used with user buffer of Z bytes,
and SO_PEEK_OFF of X bytes, from a skb with Y bytes, and following
condition :
Z < X < Y
kernel BUG at mm/usercopy.c:72!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 0 PID: 2917 Comm: syzkaller842281 Not tainted 4.13.0-rc3+ #16
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
task:
ffff8801d2fa40c0 task.stack:
ffff8801d1fe8000
RIP: 0010:report_usercopy mm/usercopy.c:64 [inline]
RIP: 0010:__check_object_size+0x3ad/0x500 mm/usercopy.c:264
RSP: 0018:
ffff8801d1fef8a8 EFLAGS:
00010286
RAX:
0000000000000078 RBX:
ffffffff847102c0 RCX:
0000000000000000
RDX:
0000000000000078 RSI:
1ffff1003a3fded5 RDI:
ffffed003a3fdf09
RBP:
ffff8801d1fef998 R08:
0000000000000001 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000000 R12:
ffff8801d1ea480e
R13:
fffffffffffffffa R14:
ffffffff84710280 R15:
dffffc0000000000
FS:
0000000001360880(0000) GS:
ffff8801dc000000(0000)
knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00000000202ecfe4 CR3:
00000001d1ff8000 CR4:
00000000001406f0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
check_object_size include/linux/thread_info.h:108 [inline]
check_copy_size include/linux/thread_info.h:139 [inline]
copy_to_iter include/linux/uio.h:105 [inline]
copy_linear_skb include/net/udp.h:371 [inline]
udpv6_recvmsg+0x1040/0x1af0 net/ipv6/udp.c:395
inet_recvmsg+0x14c/0x5f0 net/ipv4/af_inet.c:793
sock_recvmsg_nosec net/socket.c:792 [inline]
sock_recvmsg+0xc9/0x110 net/socket.c:799
SYSC_recvfrom+0x2d6/0x570 net/socket.c:1788
SyS_recvfrom+0x40/0x50 net/socket.c:1760
entry_SYSCALL_64_fastpath+0x1f/0xbe
Fixes:
b65ac44674dd ("udp: try to avoid 2 cache miss on dequeue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 11 Aug 2017 21:59:24 +0000 (14:59 -0700)]
Merge branch 'bpf-Minor-fix-in-bpf_convert_ctx_access'
Daniel Borkmann says:
====================
bpf: Minor fix in bpf_convert_ctx_access
First one was found while trying to compile the kernel
with !CONFIG_NET_RX_BUSY_POLL.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 11 Aug 2017 16:31:25 +0000 (18:31 +0200)]
bpf: fix two missing target_size settings in bpf_convert_ctx_access
When CONFIG_NET_SCHED or CONFIG_NET_RX_BUSY_POLL is /not/ set and
we try a narrow __sk_buff load of tc_index or napi_id, respectively,
then verifier rightfully complains that it's misconfigured, because
we need to set target_size in each of the two cases. The rewrite
for the ctx access is just a dummy op, but needs to pass, so fix
this up.
Fixes:
f96da09473b5 ("bpf: simplify narrower ctx access")
Reported-by: Shubham Bansal <illusionist.neo@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 11 Aug 2017 16:31:24 +0000 (18:31 +0200)]
net: fix compilation when busy poll is not enabled
MIN_NAPI_ID is used in various places outside of
CONFIG_NET_RX_BUSY_POLL wrapping, so when it's not set
we run into build errors such as:
net/core/dev.c: In function 'dev_get_by_napi_id':
net/core/dev.c:886:16: error: ‘MIN_NAPI_ID’ undeclared (first use in this function)
if (napi_id < MIN_NAPI_ID)
^~~~~~~~~~~
Thus, have MIN_NAPI_ID always defined to fix these errors.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Vasilyev [Fri, 11 Aug 2017 12:57:22 +0000 (15:57 +0300)]
mISDN: Fix null pointer dereference at mISDN_FsmNew
If mISDN_FsmNew() fails to allocate memory for jumpmatrix
then null pointer dereference will occur on any write to
jumpmatrix.
The patch adds check on successful allocation and
corresponding error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Fri, 11 Aug 2017 08:18:20 +0000 (10:18 +0200)]
nfp: do not update MTU from BH in flower app
The Flower app may receive a request to update the MTU of a representor
netdev upon receipt of a control message from the firmware. This requires
the RTNL lock which needs to be taken outside of the packet processing
path.
As a handling of this correctly seems a little to invasive for a fix simply
skip setting the MTU for now.
Relevant backtrace:
[ 1496.288489] BUG: scheduling while atomic: kworker/0:3/373/0x00000100
[ 1496.294911] dca syscopyarea sysfillrect sysimgblt fb_sys_fops ptp drm mxm_wmi ahci pps_core libahci i2c_algo_bit wmi [last unloaded: nfp]
[ 1496.294918] CPU: 0 PID: 373 Comm: kworker/0:3 Tainted: G OE 4.13.0-rc3+ #3
[ 1496.294919] Hardware name: Supermicro X10DRi/X10DRi, BIOS 2.0 12/28/2015
[ 1496.294923] Workqueue: events work_for_cpu_fn
[ 1496.294924] Call Trace:
[ 1496.294927] <IRQ>
[ 1496.294931] dump_stack+0x63/0x82
[ 1496.294935] __schedule_bug+0x54/0x70
[ 1496.294937] __schedule+0x62f/0x890
[ 1496.294941] ? intel_unmap_sg+0x90/0x90
[ 1496.294942] schedule+0x36/0x80
[ 1496.294943] schedule_preempt_disabled+0xe/0x10
[ 1496.294945] __mutex_lock.isra.2+0x445/0x4a0
[ 1496.294947] ? device_is_rmrr_locked+0x12/0x50
[ 1496.294950] ? kfree+0x162/0x170
[ 1496.294952] ? device_is_rmrr_locked+0x12/0x50
[ 1496.294953] ? iommu_should_identity_map+0x50/0xe0
[ 1496.294954] __mutex_lock_slowpath+0x13/0x20
[ 1496.294955] ? iommu_no_mapping+0x48/0xd0
[ 1496.294956] ? __mutex_lock_slowpath+0x13/0x20
[ 1496.294957] mutex_lock+0x2f/0x40
[ 1496.294960] rtnl_lock+0x15/0x20
[ 1496.294979] nfp_flower_cmsg_rx+0xc8/0x150 [nfp]
[ 1496.294986] nfp_ctrl_poll+0x286/0x350 [nfp]
[ 1496.294989] tasklet_action+0xf6/0x110
[ 1496.294992] __do_softirq+0xed/0x278
[ 1496.294993] irq_exit+0xb6/0xc0
[ 1496.294994] do_IRQ+0x4f/0xd0
[ 1496.294996] common_interrupt+0x89/0x89
Fixes:
948faa46c05b ("nfp: add support for control messages for flower app")
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Romain Perier [Thu, 10 Aug 2017 14:56:05 +0000 (16:56 +0200)]
net: stmmac: Use the right logging function in stmmac_mdio_register
Currently, the function stmmac_mdio_register() is only used by
stmmac_dvr_probe() from stmmac_main.c, in order to register the MDIO bus
and probe information about the PHY. As this function is called before
calling register_netdev(), all messages logged from stmmac_mdio_register
are prefixed by "(unnamed net_device)". The goal of netdev_info or
netdev_err is to dump useful infos about a net_device, when this data
structure is partially initialized, there is no point for using these
functions.
This commit fixes the issue by replacing all netdev_*() by the
corresponding dev_*() function for logging. The last netdev_info is
replaced by phy_attached_info(), as a valid phydev can be used at this
point.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Konstantin Khlebnikov [Thu, 10 Aug 2017 09:31:40 +0000 (12:31 +0300)]
net/sched/hfsc: allocate tcf block for hfsc root class
Without this filters cannot be attached.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Fixes:
6529eaba33f0 ("net: sched: introduce tcf block infractructure")
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Born [Thu, 10 Aug 2017 04:41:44 +0000 (06:41 +0200)]
bonding: require speed/duplex only for 802.3ad, alb and tlb
The patch
c4adfc822bf5 ("bonding: make speed, duplex setting consistent
with link state") puts the link state to down if
bond_update_speed_duplex() cannot retrieve speed and duplex settings.
Assumably the patch was written with 802.3ad mode in mind which relies
on link speed/duplex settings. For other modes like active-backup these
settings are not required. Thus, only for these other modes, this patch
reintroduces support for slaves that do not support reporting speed or
duplex such as wireless devices. This fixes the regression reported in
bug 196547 (https://bugzilla.kernel.org/show_bug.cgi?id=196547).
Fixes:
c4adfc822bf5 ("bonding: make speed, duplex setting consistent
with link state")
Signed-off-by: Andreas Born <futur.andy@googlemail.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Wed, 9 Aug 2017 20:46:09 +0000 (16:46 -0400)]
net: dsa: ksz: fix skb freeing
The DSA layer frees the original skb when an xmit function returns NULL,
meaning an error occurred. But if the tagging code copied the original
skb, it is responsible of freeing the copy if an error occurs.
The ksz tagging code currently has two issues: if skb_put_padto fails,
the skb copy is not freed, and the original skb will be freed twice.
To fix that, move skb_put_padto inside both branches of the skb_tailroom
condition, before freeing the original skb, and free the copy on error.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 10 Aug 2017 17:30:29 +0000 (10:30 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix handling of initial STATE message in TIPC, from Jon Paul Maloy.
2) Fix stats handling in bcm_sysport_get_stats(), from Florian
Fainelli.
3) Reject
16777215 VNI value in geneve_validate(), from Girish
Moodalbail.
4) Fix initial IGMP sysctl setting regression, from Nikolay Borisov.
5) Once a UFO fragmented frame is treated as UFO, we should continue
doing so. Likewise once a frame has been segmented, we should
continue doing that and not try to convert it to a UFO frame. From
Willem de Bruijn.
6) Test the AF_PACKET RX/TX ring pg_vec state under the socket lock to
prevent races. From Willem de Bruijn.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
packet: fix tp_reserve race in packet_set_ring
udp: consistently apply ufo or fragmentation
net: sched: set xt_tgchk_param par.nft_compat as 0 in ipt_init_target
igmp: Fix regression caused by igmp sysctl namespace code.
geneve: maximum value of VNI cannot be used
net: systemport: Fix software statistics for SYSTEMPORT Lite
tipc: remove premature ESTABLISH FSM event at link synchronization
Willem de Bruijn [Thu, 10 Aug 2017 16:41:58 +0000 (12:41 -0400)]
packet: fix tp_reserve race in packet_set_ring
Updates to tp_reserve can race with reads of the field in
packet_set_ring. Avoid this by holding the socket lock during
updates in setsockopt PACKET_RESERVE.
This bug was discovered by syzkaller.
Fixes:
8913336a7e8d ("packet: add PACKET_RESERVE sockopt")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Thu, 10 Aug 2017 16:29:19 +0000 (12:29 -0400)]
udp: consistently apply ufo or fragmentation
When iteratively building a UDP datagram with MSG_MORE and that
datagram exceeds MTU, consistently choose UFO or fragmentation.
Once skb_is_gso, always apply ufo. Conversely, once a datagram is
split across multiple skbs, do not consider ufo.
Sendpage already maintains the first invariant, only add the second.
IPv6 does not have a sendpage implementation to modify.
A gso skb must have a partial checksum, do not follow sk_no_check_tx
in udp_send_skb.
Found by syzkaller.
Fixes:
e89e9cf539a2 ("[IPv4/IPv6]: UFO Scatter-gather approach")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 10 Aug 2017 16:36:06 +0000 (09:36 -0700)]
Merge git://git./linux/kernel/git/davem/sparc
Pull sparc updates from David Miller:
1) Recognize M8 cpus, just basic chip ID matching, from Allen Pais.
2) Prevent crashes when bringing up sunvdc virtual block devices in
some environments. From Jim Quigley.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sunvdc: prevent sunvdc panic when mpgroup disk added to guest domain
sparc64: Increase max_phys_bits to 51 and VA bits to 53 for M8.
sparc64: recognize and support sparc M8 cpu type
sparc64: properly name the cpu constants
Xin Long [Wed, 9 Aug 2017 10:15:19 +0000 (18:15 +0800)]
net: sched: set xt_tgchk_param par.nft_compat as 0 in ipt_init_target
Commit
55917a21d0cc ("netfilter: x_tables: add context to know if
extension runs from nft_compat") introduced a member nft_compat to
xt_tgchk_param structure.
But it didn't set it's value for ipt_init_target. With unexpected
value in par.nft_compat, it may return unexpected result in some
target's checkentry.
This patch is to set all it's fields as 0 and only initialize the
non-zero fields in ipt_init_target.
v1->v2:
As Wang Cong's suggestion, fix it by setting all it's fields as
0 and only initializing the non-zero fields.
Fixes:
55917a21d0cc ("netfilter: x_tables: add context to know if extension runs from nft_compat")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Borisov [Wed, 9 Aug 2017 11:38:04 +0000 (14:38 +0300)]
igmp: Fix regression caused by igmp sysctl namespace code.
Commit
dcd87999d415 ("igmp: net: Move igmp namespace init to correct file")
moved the igmp sysctls initialization from tcp_sk_init to igmp_net_init. This
function is only called as part of per-namespace initialization, only if
CONFIG_IP_MULTICAST is defined, otherwise igmp_mc_init() call in ip_init is
compiled out, casuing the igmp pernet ops to not be registerd and those sysctl
being left initialized with 0. However, there are certain functions, such as
ip_mc_join_group which are always compiled and make use of some of those
sysctls. Let's do a partial revert of the aforementioned commit and move the
sysctl initialization into inet_init_net, that way they will always have
sane values.
Fixes:
dcd87999d415 ("igmp: net: Move igmp namespace init to correct file")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196595
Reported-by: Gerardo Exequiel Pozzi <vmlinuz386@gmail.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Girish Moodalbail [Wed, 9 Aug 2017 00:26:24 +0000 (17:26 -0700)]
geneve: maximum value of VNI cannot be used
Geneve's Virtual Network Identifier (VNI) is 24 bit long, so the range
of values for it would be from 0 to
16777215 (2^24 -1). However, one
cannot create a geneve device with VNI set to
16777215. This patch fixes
this issue.
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 8 Aug 2017 21:45:09 +0000 (14:45 -0700)]
net: systemport: Fix software statistics for SYSTEMPORT Lite
With SYSTEMPORT Lite we have holes in our statistics layout that make us
skip over the hardware MIB counters, bcm_sysport_get_stats() was not
taking that into account resulting in reporting 0 for all SW-maintained
statistics, fix this by skipping accordingly.
Fixes:
44a4524c54af ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Tue, 8 Aug 2017 20:23:56 +0000 (22:23 +0200)]
tipc: remove premature ESTABLISH FSM event at link synchronization
When a link between two nodes come up, both endpoints will initially
send out a STATE message to the peer, to increase the probability that
the peer endpoint also is up when the first traffic message arrives.
Thereafter, if the establishing link is the second link between two
nodes, this first "traffic" message is a TUNNEL_PROTOCOL/SYNCH message,
helping the peer to perform initial synchronization between the two
links.
However, the initial STATE message may be lost, in which case the SYNCH
message will be the first one arriving at the peer. This should also
work, as the SYNCH message itself will be used to take up the link
endpoint before initializing synchronization.
Unfortunately the code for this case is broken. Currently, the link is
brought up through a tipc_link_fsm_evt(ESTABLISHED) when a SYNCH
arrives, whereupon __tipc_node_link_up() is called to distribute the
link slots and take the link into traffic. But, __tipc_node_link_up() is
itself starting with a test for whether the link is up, and if true,
returns without action. Clearly, the tipc_link_fsm_evt(ESTABLISHED) call
is unnecessary, since tipc_node_link_up() is itself issuing such an
event, but also harmful, since it inhibits tipc_node_link_up() to
perform the test of its tasks, and the link endpoint in question hence
is never taken into traffic.
This problem has been exposed when we set up dual links between pre-
and post-4.4 kernels, because the former ones don't send out the
initial STATE message described above.
We fix this by removing the unnecessary event call.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jim Quigley [Fri, 21 Jul 2017 13:20:15 +0000 (09:20 -0400)]
sunvdc: prevent sunvdc panic when mpgroup disk added to guest domain
Using mpgroup to define multiple paths for a virtual disk causes multiple
virtual-device-port ports to be created for that virtual device.
Each virtual-device-port port then gets a vdisk created for it by the Linux
sunvdc driver. As mpgroup is not supported by the Linux sunvdc driver it
cannot handle multiple ports for a single vdisk, leading to a kernel panic
at startup.
This fix prevents more than one vdisk per virtual-device-port being created
until full virtual disk multipathing (mpgroup) support is implemented.
Signed-off-by: Jim Quigley <Jim.Quigley@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Reviewed-by: Aaron Young <aaron.young@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 9 Aug 2017 21:30:34 +0000 (14:30 -0700)]
Merge tag 'pinctrl-v4.13-2' of git://git./linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"These are the pin control fixes I have gathered since the return from
my vacation. They boiled in -next a while so let's get them in.
Apart from the documentation build it is purely driver fixes. Which is
nice. The Intel fixes seem kind of important.
- Fix the documentation build as the docs were moved
- Correct the UART pin list on the Intel Merrifield
- Fix pin assignment and number of pins on the Marvell Armada 37xx
pin controller
- Cover the Setzer models in the Chromebook DMI quirk in the Intel
cheryview driver so they start working
- Add the missing "sim" function to the sunxi driver
- Fix USB pin definitions on Uniphier Pro4
- Smatch fix for invalid reference in the zx pin control driver"
* tag 'pinctrl-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: generic: update references to Documentation/pinctrl.txt
pinctrl: intel: merrifield: Correct UART pin lists
pinctrl: armada-37xx: Fix number of pin in south bridge
pinctrl: armada-37xx: Fix the pin 23 on south bridge
pinctrl: cherryview: Add Setzer models to the Chromebook DMI quirk
pinctrl: sunxi: add a missing function of A10/A20 pinctrl driver
pinctrl: uniphier: fix USB3 pin assignment for Pro4
pinctrl: zte: fix dereference of 'data' in zx_set_mux()
Mel Gorman [Wed, 9 Aug 2017 07:27:11 +0000 (08:27 +0100)]
futex: Remove unnecessary warning from get_futex_key
Commit
65d8fc777f6d ("futex: Remove requirement for lock_page() in
get_futex_key()") removed an unnecessary lock_page() with the
side-effect that page->mapping needed to be treated very carefully.
Two defensive warnings were added in case any assumption was missed and
the first warning assumed a correct application would not alter a
mapping backing a futex key. Since merging, it has not triggered for
any unexpected case but Mark Rutland reported the following bug
triggering due to the first warning.
kernel BUG at kernel/futex.c:679!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 3695 Comm: syz-executor1 Not tainted
4.13.0-rc3-00020-g307fec773ba3 #3
Hardware name: linux,dummy-virt (DT)
task:
ffff80001e271780 task.stack:
ffff000010908000
PC is at get_futex_key+0x6a4/0xcf0 kernel/futex.c:679
LR is at get_futex_key+0x6a4/0xcf0 kernel/futex.c:679
pc : [<
ffff00000821ac14>] lr : [<
ffff00000821ac14>] pstate:
80000145
The fact that it's a bug instead of a warning was due to an unrelated
arm64 problem, but the warning itself triggered because the underlying
mapping changed.
This is an application issue but from a kernel perspective it's a
recoverable situation and the warning is unnecessary so this patch
removes the warning. The warning may potentially be triggered with the
following test program from Mark although it may be necessary to adjust
NR_FUTEX_THREADS to be a value smaller than the number of CPUs in the
system.
#include <linux/futex.h>
#include <pthread.h>
#include <stdio.h>
#include <stdlib.h>
#include <sys/mman.h>
#include <sys/syscall.h>
#include <sys/time.h>
#include <unistd.h>
#define NR_FUTEX_THREADS 16
pthread_t threads[NR_FUTEX_THREADS];
void *mem;
#define MEM_PROT (PROT_READ | PROT_WRITE)
#define MEM_SIZE 65536
static int futex_wrapper(int *uaddr, int op, int val,
const struct timespec *timeout,
int *uaddr2, int val3)
{
syscall(SYS_futex, uaddr, op, val, timeout, uaddr2, val3);
}
void *poll_futex(void *unused)
{
for (;;) {
futex_wrapper(mem, FUTEX_CMP_REQUEUE_PI, 1, NULL, mem + 4, 1);
}
}
int main(int argc, char *argv[])
{
int i;
mem = mmap(NULL, MEM_SIZE, MEM_PROT,
MAP_SHARED | MAP_ANONYMOUS, -1, 0);
printf("Mapping @ %p\n", mem);
printf("Creating futex threads...\n");
for (i = 0; i < NR_FUTEX_THREADS; i++)
pthread_create(&threads[i], NULL, poll_futex, NULL);
printf("Flipping mapping...\n");
for (;;) {
mmap(mem, MEM_SIZE, MEM_PROT,
MAP_FIXED | MAP_SHARED | MAP_ANONYMOUS, -1, 0);
}
return 0;
}
Reported-and-tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 9 Aug 2017 20:21:28 +0000 (13:21 -0700)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"The main thing is to allow empty id_tables for ACPI to make some
drivers get probed again. It looks a bit bigger than usual because it
needs some internal renaming, too.
Other than that, there is a fix for broken DSTDs, a super simple
enablement for ARM MPS, and two documentation fixes which I'd like to
see in v4.13 already"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rephrase explanation of I2C_CLASS_DEPRECATED
i2c: allow i2c-versatile for ARM MPS platforms
i2c: designware: Some broken DSTDs use 1MiHz instead of 1MHz
i2c: designware: Print clock freq on invalid clock freq error
i2c: core: Allow empty id_table in ACPI case as well
i2c: mux: pinctrl: mention correct module name in Kconfig help text
Linus Torvalds [Wed, 9 Aug 2017 17:37:35 +0000 (10:37 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Three patches that should go into this release.
Two of them are from Paolo and fix up some corner cases with BFQ, and
the last patch is from Ming and fixes up a potential usage count
imbalance regression due to the recent NOWAIT work"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: don't leak preempt counter/q_usage_counter when allocating rq failed
block, bfq: consider also in_service_entity to state whether an entity is active
block, bfq: reset in_service_entity if it becomes idle
Linus Torvalds [Wed, 9 Aug 2017 17:33:49 +0000 (10:33 -0700)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"Fix two regressions in the inside-secure driver with respect to
hmac(sha1)"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: inside-secure - fix the sha state length in hmac_sha1_setkey
crypto: inside-secure - fix invalidation check in hmac_sha1_setkey
Linus Torvalds [Wed, 9 Aug 2017 17:14:04 +0000 (10:14 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"The pull requests are getting smaller, that's progress I suppose :-)
1) Fix infinite loop in CIPSO option parsing, from Yujuan Qi.
2) Fix remote checksum handling in VXLAN and GUE tunneling drivers,
from Koichiro Den.
3) Missing u64_stats_init() calls in several drivers, from Florian
Fainelli.
4) TCP can set the congestion window to an invalid ssthresh value
after congestion window reductions, from Yuchung Cheng.
5) Fix BPF jit branch generation on s390, from Daniel Borkmann.
6) Correct MIPS ebpf JIT merge, from David Daney.
7) Correct byte order test in BPF test_verifier.c, from Daniel
Borkmann.
8) Fix various crashes and leaks in ASIX driver, from Dean Jenkins.
9) Handle SCTP checksums properly in mlx4 driver, from Davide
Caratti.
10) We can potentially enter tcp_connect() with a cached route
already, due to fastopen, so we have to explicitly invalidate it.
11) skb_warn_bad_offload() can bark in legitimate situations, fix from
Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
net: avoid skb_warn_bad_offload false positives on UFO
qmi_wwan: fix NULL deref on disconnect
ppp: fix xmit recursion detection on ppp channels
rds: Reintroduce statistics counting
tcp: fastopen: tcp_connect() must refresh the route
net: sched: set xt_tgchk_param par.net properly in ipt_init_target
net: dsa: mediatek: add adjust link support for user ports
net/mlx4_en: don't set CHECKSUM_COMPLETE on SCTP packets
qed: Fix a memory allocation failure test in 'qed_mcp_cmd_init()'
hysdn: fix to a race condition in put_log_buffer
s390/qeth: fix L3 next-hop in xmit qeth hdr
asix: Fix small memory leak in ax88772_unbind()
asix: Ensure asix_rx_fixup_info members are all reset
asix: Add rx->ax_skb = NULL after usbnet_skb_return()
bpf: fix selftest/bpf/test_pkt_md_access on s390x
netvsc: fix race on sub channel creation
bpf: fix byte order test in test_verifier
xgene: Always get clk source, but ignore if it's missing for SGMII ports
MIPS: Add missing file for eBPF JIT.
bpf, s390: fix build for libbpf and selftest suite
...
Willem de Bruijn [Tue, 8 Aug 2017 18:22:55 +0000 (14:22 -0400)]
net: avoid skb_warn_bad_offload false positives on UFO
skb_warn_bad_offload triggers a warning when an skb enters the GSO
stack at __skb_gso_segment that does not have CHECKSUM_PARTIAL
checksum offload set.
Commit
b2504a5dbef3 ("net: reduce skb_warn_bad_offload() noise")
observed that SKB_GSO_DODGY producers can trigger the check and
that passing those packets through the GSO handlers will fix it
up. But, the software UFO handler will set ip_summed to
CHECKSUM_NONE.
When __skb_gso_segment is called from the receive path, this
triggers the warning again.
Make UFO set CHECKSUM_UNNECESSARY instead of CHECKSUM_NONE. On
Tx these two are equivalent. On Rx, this better matches the
skb state (checksum computed), as CHECKSUM_NONE here means no
checksum computed.
See also this thread for context:
http://patchwork.ozlabs.org/patch/799015/
Fixes:
b2504a5dbef3 ("net: reduce skb_warn_bad_offload() noise")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Tue, 8 Aug 2017 16:02:11 +0000 (18:02 +0200)]
qmi_wwan: fix NULL deref on disconnect
qmi_wwan_disconnect is called twice when disconnecting devices with
separate control and data interfaces. The first invocation will set
the interface data to NULL for both interfaces to flag that the
disconnect has been handled. But the matching NULL check was left
out when qmi_wwan_disconnect was added, resulting in this oops:
usb 2-1.4: USB disconnect, device number 4
qmi_wwan 2-1.4:1.6 wwp0s29u1u4i6: unregister 'qmi_wwan' usb-0000:00:1d.0-1.4, WWAN/QMI device
BUG: unable to handle kernel NULL pointer dereference at
00000000000000e0
IP: qmi_wwan_disconnect+0x25/0xc0 [qmi_wwan]
PGD 0
P4D 0
Oops: 0000 [#1] SMP
Modules linked in: <stripped irrelevant module list>
CPU: 2 PID: 33 Comm: kworker/2:1 Tainted: G E 4.12.3-nr44-normandy-r1500619820+ #1
Hardware name: LENOVO 4291LR7/4291LR7, BIOS CBET4000
4.6-810-g50522254fb 07/21/2017
Workqueue: usb_hub_wq hub_event [usbcore]
task:
ffff8c882b716040 task.stack:
ffffb8e800d84000
RIP: 0010:qmi_wwan_disconnect+0x25/0xc0 [qmi_wwan]
RSP: 0018:
ffffb8e800d87b38 EFLAGS:
00010246
RAX:
0000000000000000 RBX:
0000000000000000 RCX:
0000000000000000
RDX:
0000000000000001 RSI:
ffff8c8824f3f1d0 RDI:
ffff8c8824ef6400
RBP:
ffff8c8824ef6400 R08:
0000000000000000 R09:
0000000000000000
R10:
ffffb8e800d87780 R11:
0000000000000011 R12:
ffffffffc07ea0e8
R13:
ffff8c8824e2e000 R14:
ffff8c8824e2e098 R15:
0000000000000000
FS:
0000000000000000(0000) GS:
ffff8c8835300000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00000000000000e0 CR3:
0000000229ca5000 CR4:
00000000000406e0
Call Trace:
? usb_unbind_interface+0x71/0x270 [usbcore]
? device_release_driver_internal+0x154/0x210
? qmi_wwan_unbind+0x6d/0xc0 [qmi_wwan]
? usbnet_disconnect+0x6c/0xf0 [usbnet]
? qmi_wwan_disconnect+0x87/0xc0 [qmi_wwan]
? usb_unbind_interface+0x71/0x270 [usbcore]
? device_release_driver_internal+0x154/0x210
Reported-and-tested-by: Nathaniel Roach <nroach44@gmail.com>
Fixes:
c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Tue, 8 Aug 2017 09:43:24 +0000 (11:43 +0200)]
ppp: fix xmit recursion detection on ppp channels
Commit
e5dadc65f9e0 ("ppp: Fix false xmit recursion detect with two ppp
devices") dropped the xmit_recursion counter incrementation in
ppp_channel_push() and relied on ppp_xmit_process() for this task.
But __ppp_channel_push() can also send packets directly (using the
.start_xmit() channel callback), in which case the xmit_recursion
counter isn't incremented anymore. If such packets get routed back to
the parent ppp unit, ppp_xmit_process() won't notice the recursion and
will call ppp_channel_push() on the same channel, effectively creating
the deadlock situation that the xmit_recursion mechanism was supposed
to prevent.
This patch re-introduces the xmit_recursion counter incrementation in
ppp_channel_push(). Since the xmit_recursion variable is now part of
the parent ppp unit, incrementation is skipped if the channel doesn't
have any. This is fine because only packets routed through the parent
unit may enter the channel recursively.
Finally, we have to ensure that pch->ppp is not going to be modified
while executing ppp_channel_push(). Instead of taking this lock only
while calling ppp_xmit_process(), we now have to hold it for the full
ppp_channel_push() execution. This respects the ppp locks ordering
which requires locking ->upl before ->downl.
Fixes:
e5dadc65f9e0 ("ppp: Fix false xmit recursion detect with two ppp devices")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Håkon Bugge [Tue, 8 Aug 2017 09:13:32 +0000 (11:13 +0200)]
rds: Reintroduce statistics counting
In commit
7e3f2952eeb1 ("rds: don't let RDS shutdown a connection
while senders are present"), refilling the receive queue was removed
from rds_ib_recv(), along with the increment of
s_ib_rx_refill_from_thread.
Commit
73ce4317bf98 ("RDS: make sure we post recv buffers")
re-introduces filling the receive queue from rds_ib_recv(), but does
not add the statistics counter. rds_ib_recv() was later renamed to
rds_ib_recv_path().
This commit reintroduces the statistics counting of
s_ib_rx_refill_from_thread and s_ib_rx_refill_from_cq.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: Knut Omang <knut.omang@oracle.com>
Reviewed-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Reviewed-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 8 Aug 2017 08:41:58 +0000 (01:41 -0700)]
tcp: fastopen: tcp_connect() must refresh the route
With new TCP_FASTOPEN_CONNECT socket option, there is a possibility
to call tcp_connect() while socket sk_dst_cache is either NULL
or invalid.
+0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 4
+0 fcntl(4, F_SETFL, O_RDWR|O_NONBLOCK) = 0
+0 setsockopt(4, SOL_TCP, TCP_FASTOPEN_CONNECT, [1], 4) = 0
+0 connect(4, ..., ...) = 0
<< sk->sk_dst_cache becomes obsolete, or even set to NULL >>
+1 sendto(4, ..., 1000, MSG_FASTOPEN, ..., ...) = 1000
We need to refresh the route otherwise bad things can happen,
especially when syzkaller is running on the host :/
Fixes:
19f6d3f3c8422 ("net/tcp-fastopen: Add new API support")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 8 Aug 2017 07:25:25 +0000 (15:25 +0800)]
net: sched: set xt_tgchk_param par.net properly in ipt_init_target
Now xt_tgchk_param par in ipt_init_target is a local varibale,
par.net is not initialized there. Later when xt_check_target
calls target's checkentry in which it may access par.net, it
would cause kernel panic.
Jaroslav found this panic when running:
# ip link add TestIface type dummy
# tc qd add dev TestIface ingress handle ffff:
# tc filter add dev TestIface parent ffff: u32 match u32 0 0 \
action xt -j CONNMARK --set-mark 4
This patch is to pass net param into ipt_init_target and set
par.net with it properly in there.
v1->v2:
As Wang Cong pointed, I missed ipt_net_id != xt_net_id, so fix
it by also passing net_id to __tcf_ipt_init.
v2->v3:
Missed the fixes tag, so add it.
Fixes:
ecb2421b5ddf ("netfilter: add and use nf_ct_netns_get/put")
Reported-by: Jaroslav Aster <jaster@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Crispin [Mon, 7 Aug 2017 14:20:49 +0000 (16:20 +0200)]
net: dsa: mediatek: add adjust link support for user ports
Manually adjust the port settings of user ports once PHY polling has
completed. This patch extends the adjust_link callback to configure the
per port PMCR register, applying the proper values polled from the PHY.
Without this patch flow control was not always getting setup properly.
Signed-off-by: Shashidhar Lakkavalli <shashidhar.lakkavalli@openmesh.com>
Signed-off-by: Muciri Gatimu <muciri@openmesh.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Thu, 3 Aug 2017 20:54:48 +0000 (22:54 +0200)]
net/mlx4_en: don't set CHECKSUM_COMPLETE on SCTP packets
if the NIC fails to validate the checksum on TCP/UDP, and validation of IP
checksum is successful, the driver subtracts the pseudo-header checksum
from the value obtained by the hardware and sets CHECKSUM_COMPLETE. Don't
do that if protocol is IPPROTO_SCTP, otherwise CRC32c validation fails.
V2: don't test MLX4_CQE_STATUS_IPV6 if MLX4_CQE_STATUS_IPV4 is set
Reported-by: Shuang Li <shuali@redhat.com>
Fixes:
f8c6455bb04b ("net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 8 Aug 2017 18:42:33 +0000 (11:42 -0700)]
Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Third set of -rc fixes for 4.13 cycle
- small set of miscellanous fixes
- a reasonably sizable set of IPoIB fixes that deal with multiple
long standing issues"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/hns: checking for IS_ERR() instead of NULL
RDMA/mlx5: Fix existence check for extended address vector
IB/uverbs: Fix device cleanup
RDMA/uverbs: Prevent leak of reserved field
IB/core: Fix race condition in resolving IP to MAC
IB/ipoib: Notify on modify QP failure only when relevant
Revert "IB/core: Allow QP state transition from reset to error"
IB/ipoib: Remove double pointer assigning
IB/ipoib: Clean error paths in add port
IB/ipoib: Add get statistics support to SRIOV VF
IB/ipoib: Add multicast packets statistics
IB/ipoib: Set IPOIB_NEIGH_TBL_FLUSH after flushed completion initialization
IB/ipoib: Prevent setting negative values to max_nonsrq_conn_qp
IB/ipoib: Make sure no in-flight joins while leaving that mcast
IB/ipoib: Use cancel_delayed_work_sync when needed
IB/ipoib: Fix race between light events and interface restart
Joe Perches [Sun, 6 Aug 2017 01:45:49 +0000 (18:45 -0700)]
parse-maintainers: Move matching sections from MAINTAINERS
Allow any number of command line arguments to match either the
section header or the section contents and create new files.
Create MAINTAINERS.new and SECTION.new.
This allows scripting of the movement of various sections from
MAINTAINERS.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Sun, 6 Aug 2017 01:45:48 +0000 (18:45 -0700)]
parse-maintainers: Use perl hash references and specific filenames
Instead of reading STDIN and writing STDOUT, use specific filenames of
MAINTAINERS and MAINTAINERS.new.
Use hash references instead of global hash %hash so future modifications
can read and write specific hashes to split up MAINTAINERS into multiple
files using a script.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Sun, 6 Aug 2017 01:45:47 +0000 (18:45 -0700)]
parse-maintainers: Add section pattern sorting
Section [A-Z]: patterns are not currently in any required sorting order.
Add a specific sorting sequence to MAINTAINERS entries.
Sort F: and X: patterns in alphabetic order.
The preferred section ordering is:
SECTION HEADER
M: Maintainers
R: Reviewers
P: Named persons without email addresses
L: Mailing list addresses
S: Status of this section (Supported, Maintained, Orphan, etc...)
W: Any relevant URLs
T: Source code control type (git, quilt, etc)
Q: Patchwork patch acceptance queue site
B: Bug tracking URIs
C: Chat URIs
F: Files with wildcard patterns (alphabetic ordered)
X: Excluded files with wildcard patterns (alphabetic ordered)
N: Files with regex patterns
K: Keyword regexes in source code for maintainership identification
Miscellaneous perl neatening:
- Rename %map to %hash, map has a different meaning in perl
- Avoid using \& and local variables for function indirection
- Use return for a little c like clarity
- Use c-like function call style instead of &function
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Sat, 5 Aug 2017 04:45:48 +0000 (21:45 -0700)]
get_maintainer: Prepare for separate MAINTAINERS files
Allow for MAINTAINERS to become a directory and if it is,
read all the files in the directory for maintained sections.
Optionally look for all files named MAINTAINERS in directories
excluding the .git directory by using --find-maintainer-files.
This optional feature adds ~.3 seconds of CPU on an Intel
i5-6200 with an SSD.
Miscellanea:
- Create a read_maintainer_file subroutine from the existing code
- Test only the existence of MAINTAINERS, not whether it's a file
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Wed, 2 Aug 2017 17:57:45 +0000 (10:57 -0700)]
MAINTAINERS: openbmc mailing list is moderated
The openbmc mailing list is moderated for non-subscribers.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sedat Dilek [Tue, 25 Jul 2017 12:53:42 +0000 (14:53 +0200)]
MAINTAINERS: greybus: Fix typo s/LOOBACK/LOOPBACK
Fixes:
f47e07bc5f1a5c48 ("Fix up MAINTAINERS file problems")
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 8 Aug 2017 16:38:41 +0000 (09:38 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes, one re-fix of a previous fix and five patches sorting
out hotplug in the bnx2X class of drivers. The latter is rather
involved, but necessary because these drivers have started dropping
lockdep recursion warnings on the hotplug lock because of its
conversion to a percpu rwsem"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sg: only check for dxfer_len greater than 256M
scsi: aacraid: reading out of bounds
scsi: qedf: Limit number of CQs
scsi: bnx2i: Simplify cpu hotplug code
scsi: bnx2fc: Simplify CPU hotplug code
scsi: bnx2i: Prevent recursive cpuhotplug locking
scsi: bnx2fc: Prevent recursive cpuhotplug locking
scsi: bnx2fc: Plug CPU hotplug race
Helge Deller [Tue, 8 Aug 2017 16:28:41 +0000 (18:28 +0200)]
random: fix warning message on ia64 and parisc
Fix the warning message on the parisc and IA64 architectures to show the
correct function name of the caller by using %pS instead of %pF. The
message is printed with the value of _RET_IP_ which calls
__builtin_return_address(0) and as such returns the IP address caller
instead of pointer to a function descriptor of the caller.
The effect of this patch is visible on the parisc and ia64 architectures
only since those are the ones which use function descriptors while on
all others %pS and %pF will behave the same.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes:
eecabf567422 ("random: suppress spammy warnings about unseeded randomness")
Fixes:
d06bfd1989fe ("random: warn when kernel uses unseeded randomness")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 8 Aug 2017 01:58:10 +0000 (18:58 -0700)]
Merge tag 'xtensa-
20170807' of git://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa fixes from Max Filippov:
- use asm-generic instances of asm/param.h and asm/device.h instead of
exact copies in arch/xtensa/include/asm;
- fix build error for xtensa cores with aliasing WT cache: define cache
flushing functions and copy_{to,from}_user_page;
- add missing EXPORT_SYMBOLs for clear_user_highpage, copy_user_highpage,
flush_dcache_page, local_flush_cache_range, local_flush_cache_page,
csum_partial and csum_partial_copy_generic.
* tag 'xtensa-
20170807' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: mm/cache: add missing EXPORT_SYMBOLs
xtensa: don't limit csum_partial export by CONFIG_NET
xtensa: fix cache aliasing handling code for WT cache
xtensa: remove wrapper header for asm/param.h
xtensa: remove wrapper header for asm/device.h
Linus Torvalds [Tue, 8 Aug 2017 01:40:18 +0000 (18:40 -0700)]
Merge tag 'for-linus-
20170807' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"I missed getting these out for rc4, but here are some MTD fixes.
Just NAND fixes (in both the core handling, and a few drivers). Notes
stolen from Boris:
Core fixes:
- fix data interface setup for ONFI NANDs that do not support the SET
FEATURES command
- fix a kernel doc header
- fix potential integer overflow when retrieving timing information
from the parameter page
- fix wrong OOB layout for small page NANDs
Driver fixes:
- fix potential division-by-zero bug
- fix backward compat with old atmel-nand DT bindings
- fix ->setup_data_interface() in the atmel NAND driver"
* tag 'for-linus-
20170807' of git://git.infradead.org/linux-mtd:
mtd: nand: atmel: Fix EDO mode check
mtd: nand: Declare tBERS, tR and tPROG as u64 to avoid integer overflow
mtd: nand: Fix timing setup for NANDs that do not support SET FEATURES
mtd: nand: Fix a docs build warning
mtd: nand: sunxi: fix potential divide-by-zero error
nand: fix wrong default oob layout for small pages using soft ecc
mtd: nand: atmel: Fix DT backward compatibility in pmecc.c
Linus Torvalds [Tue, 8 Aug 2017 01:16:22 +0000 (18:16 -0700)]
Merge tag 'xfs-4.13-fixes-3' of git://git./fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"I have a couple more bug fixes for you today:
- fix memory leak when issuing discard
- fix propagation of the dax inode flag"
* tag 'xfs-4.13-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: Fix per-inode DAX flag inheritance
xfs: Fix leak of discard bio
Christophe Jaillet [Sun, 6 Aug 2017 22:00:17 +0000 (00:00 +0200)]
qed: Fix a memory allocation failure test in 'qed_mcp_cmd_init()'
We allocate 'p_info->mfw_mb_cur' and 'p_info->mfw_mb_shadow' but we check
'p_info->mfw_mb_addr' instead of 'p_info->mfw_mb_cur'.
'p_info->mfw_mb_addr' is never 0, because it is initiliazed a few lines
above in 'qed_load_mcp_offsets()'.
Update the test and check the result of the 2 'kzalloc()' instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Volkov [Mon, 7 Aug 2017 12:54:14 +0000 (15:54 +0300)]
hysdn: fix to a race condition in put_log_buffer
The synchronization type that was used earlier to guard the loop that
deletes unused log buffers may lead to a situation that prevents any
thread from going through the loop.
The patch deletes previously used synchronization mechanism and moves
the loop under the spin_lock so the similar cases won't be feasible in
the future.
Found by by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Volkov <avolkov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Mon, 7 Aug 2017 11:28:39 +0000 (13:28 +0200)]
s390/qeth: fix L3 next-hop in xmit qeth hdr
On L3, the qeth_hdr struct needs to be filled with the next-hop
IP address.
The current code accesses rtable->rt_gateway without checking that
rtable is a valid address. The accidental access to a lowcore area
results in a random next-hop address in the qeth_hdr.
rtable (or more precisely, skb_dst(skb)) can be NULL in rare cases
(for instance together with AF_PACKET sockets).
This patch adds the missing NULL-ptr checks.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Fixes:
87e7597b5a3 qeth: Move away from using neighbour entries in qeth_l3_fill_header()
Signed-off-by: David S. Miller <davem@davemloft.net>
Doug Ledford [Mon, 7 Aug 2017 17:30:40 +0000 (13:30 -0400)]
Merge tag 'rdma-rc-2017-07-26' of git://git./linux/kernel/git/leon/linux-rdma into leon-ipoib
IPoIB fixes for 4.13
The patchset provides various fixes for IPoIB. It is combination of
fixes to various issues discovered during verification along with
static checkers cleanup patches.
Most of the patches are from pre-git era and hence lack of Fixes lines.
There is one exception in this IPoIB group - addition of patch revert:
Revert "IB/core: Allow QP state transition from reset to error", but
it followed by proper fix to the annoying print, so I thought it is
appropriate to include it.
Signed-off-by: Doug Ledford <dledford@redhat.com>
David S. Miller [Mon, 7 Aug 2017 17:10:19 +0000 (10:10 -0700)]
Merge branch 'asix-Improve-robustness'
Dean Jenkins says:
====================
asix: Improve robustness
Please consider taking these patches to improve the robustness of the ASIX USB
to Ethernet driver.
Failures prompting an ASIX driver code review
=============================================
On an ARM i.MX6 embedded platform some strange one-off and two-off failures were
observed in and around the ASIX USB to Ethernet driver. This was observed on a
highly modified kernel 3.14 with the ASIX driver containing back-ported changes
from kernel.org up to kernel 4.8 approximately.
a) A one-off failure in asix_rx_fixup_internal():
There was an occurrence of an attempt to write off the end of the netdev buffer
which was trapped by skb_over_panic() in skb_put().
[20030.846440] skbuff: skb_over_panic: text:
7f2271c0 len:120 put:60 head:
8366ecc0 data:
8366ed02 tail:0x8366ed7a end:0x8366ed40 dev:eth0
[20030.863007] Kernel BUG at
8044ce38 [verbose debug info unavailable]
[20031.215345] Backtrace:
[20031.217884] [<
8044cde0>] (skb_panic) from [<
8044d50c>] (skb_put+0x50/0x5c)
[20031.227408] [<
8044d4bc>] (skb_put) from [<
7f2271c0>] (asix_rx_fixup_internal+0x1c4/0x23c [asix])
[20031.242024] [<
7f226ffc>] (asix_rx_fixup_internal [asix]) from [<
7f22724c>] (asix_rx_fixup_common+0x14/0x18 [asix])
[20031.260309] [<
7f227238>] (asix_rx_fixup_common [asix]) from [<
7f21f7d4>] (usbnet_bh+0x74/0x224 [usbnet])
[20031.269879] [<
7f21f760>] (usbnet_bh [usbnet]) from [<
8002f834>] (call_timer_fn+0xa4/0x1f0)
[20031.283961] [<
8002f790>] (call_timer_fn) from [<
80030834>] (run_timer_softirq+0x230/0x2a8)
[20031.302782] [<
80030604>] (run_timer_softirq) from [<
80028780>] (__do_softirq+0x15c/0x37c)
[20031.321511] [<
80028624>] (__do_softirq) from [<
80028c38>] (irq_exit+0x8c/0xe8)
[20031.339298] [<
80028bac>] (irq_exit) from [<
8000e9c8>] (handle_IRQ+0x8c/0xc8)
[20031.350038] [<
8000e93c>] (handle_IRQ) from [<
800085c8>] (gic_handle_irq+0xb8/0xf8)
[20031.365528] [<
80008510>] (gic_handle_irq) from [<
8050de80>] (__irq_svc+0x40/0x70)
Analysis of the logic of the ASIX driver (containing backported changes from
kernel.org up to kernel 4.8 approximately) suggested that the software could not
trigger skb_over_panic(). The analysis of the kernel BUG() crash information
suggested that the netdev buffer was written with 2 minimal 60 octet length
Ethernet frames (ASIX hardware drops the 4 octet FCS field) and the 2nd Ethernet
frame attempted to write off the end of the netdev buffer.
Note that the netdev buffer should only contain 1 Ethernet frame so if an
attempt to write 2 Ethernet frames into the buffer is made then that is wrong.
However, the logic of the asix_rx_fixup_internal() only allows 1 Ethernet frame
to be written into the netdev buffer.
Potentially this failure was due to memory corruption because it was only seen
once.
b) Two-off failures in the NAPI layer's backlog queue:
There were 2 crashes in the NAPI layer's backlog queue presumably after
asix_rx_fixup_internal() called usbnet_skb_return().
[24097.273945] Unable to handle kernel NULL pointer dereference at virtual address
00000004
[24097.398944] PC is at process_backlog+0x80/0x16c
[24097.569466] Backtrace:
[24097.572007] [<
8045ad98>] (process_backlog) from [<
8045b64c>] (net_rx_action+0xcc/0x248)
[24097.591631] [<
8045b580>] (net_rx_action) from [<
80028780>] (__do_softirq+0x15c/0x37c)
[24097.610022] [<
80028624>] (__do_softirq) from [<
800289cc>] (run_ksoftirqd+0x2c/0x84)
and
[ 1059.828452] Unable to handle kernel NULL pointer dereference at virtual address
00000000
[ 1059.953715] PC is at process_backlog+0x84/0x16c
[ 1060.140896] Backtrace:
[ 1060.143434] [<
8045ad98>] (process_backlog) from [<
8045b64c>] (net_rx_action+0xcc/0x248)
[ 1060.163075] [<
8045b580>] (net_rx_action) from [<
80028780>] (__do_softirq+0x15c/0x37c)
[ 1060.181474] [<
80028624>] (__do_softirq) from [<
80028c38>] (irq_exit+0x8c/0xe8)
[ 1060.199256] [<
80028bac>] (irq_exit) from [<
8000e9c8>] (handle_IRQ+0x8c/0xc8)
[ 1060.210006] [<
8000e93c>] (handle_IRQ) from [<
800085c8>] (gic_handle_irq+0xb8/0xf8)
[ 1060.225492] [<
80008510>] (gic_handle_irq) from [<
8050de80>] (__irq_svc+0x40/0x70)
The embedded board was only using an ASIX USB to Ethernet adaptor eth0.
Analysis suggested that the doubly-linked list pointers of the backlog queue had
been corrupted because one of the link pointers was NULL.
Potentially this failure was due to memory corruption because it was only seen
twice.
Results of the ASIX driver code review
======================================
During the code review some weaknesses were observed in the ASIX driver and the
following patches have been created to improve the robustness.
Brief overview of the patches
-----------------------------
1. asix: Add rx->ax_skb = NULL after usbnet_skb_return()
The current ASIX driver sends the received Ethernet frame to the NAPI layer of
the network stack via the call to usbnet_skb_return() in
asix_rx_fixup_internal() but retains the rx->ax_skb pointer to the netdev
buffer. The driver no longer needs the rx->ax_skb pointer at this point because
the NAPI layer now has the Ethernet frame.
This means that asix_rx_fixup_internal() must not use rx->ax_skb after the call
to usbnet_skb_return() because it could corrupt the handling of the Ethernet
frame within the network layer.
Therefore, to remove the risk of erroneous usage of rx->ax_skb, set rx->ax_skb
to NULL after the call to usbnet_skb_return(). This avoids potential erroneous
freeing of rx->ax_skb and erroneous writing to the netdev buffer. If the
software now somehow inappropriately reused rx->ax_skb, then a NULL pointer
dereference of rx->ax_skb would occur which makes investigation easier.
2. asix: Ensure asix_rx_fixup_info members are all reset
This patch creates reset_asix_rx_fixup_info() to allow all the
asix_rx_fixup_info structure members to be consistently reset to initial
conditions.
Call reset_asix_rx_fixup_info() upon each detectable error condition so that the
next URB is processed from a known state.
Otherwise, there is a risk that some members of the asix_rx_fixup_info structure
may be incorrect after an error occurred so potentially leading to a
malfunction.
3. asix: Fix small memory leak in ax88772_unbind()
This patch creates asix_rx_fixup_common_free() to allow the rx->ax_skb to be
freed when necessary.
asix_rx_fixup_common_free() is called from ax88772_unbind() before the parent
private data structure is freed.
Without this patch, there is a risk of a small netdev buffer memory leak each
time ax88772_unbind() is called during the reception of an Ethernet frame that
spans across 2 URBs.
Testing
=======
The patches have been sanity tested on a 64-bit Linux laptop running kernel
4.13-rc2 with the 3 patches applied on top.
The ASIX USB to Adaptor used for testing was (output of lsusb):
ID 0b95:772b ASIX Electronics Corp. AX88772B
Test #1
-------
The test ran a flood ping test script which slowly incremented the ICMP Echo
Request's payload from 0 to 5000 octets. This eventually causes IPv4
fragmentation to occur which causes Ethernet frames to be sent very close to
each other so increases the probability that an Ethernet frame will span 2 URBs.
The test showed that all pings were successful. The test took about 15 minutes
to complete.
Test #2
-------
A script was run on the laptop to periodically run ifdown and ifup every second
so that the ASIX USB to Adaptor was up for 1 second and down for 1 second.
From a Linux PC connected to the laptop, the following ping command was used
ping -f -s 5000 <ip address of laptop>
The large ICMP payload causes IPv4 fragmentation resulting in multiple
Ethernet frames per original IP packet.
Kernel debug within the ASIX driver was enabled to see whether any ASIX errors
were generated. The test was run for about 24 hours and no ASIX errors were
seen.
Patches
=======
The 3 patches have been rebased off the net-next repo master branch with HEAD
fbbeefd net: fec: Allow reception of frames bigger than 1522 bytes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dean Jenkins [Mon, 7 Aug 2017 08:50:16 +0000 (09:50 +0100)]
asix: Fix small memory leak in ax88772_unbind()
When Ethernet frames span mulitple URBs, the netdev buffer memory
pointed to by the asix_rx_fixup_info structure remains allocated
during the time gap between the 2 executions of asix_rx_fixup_internal().
This means that if ax88772_unbind() is called within this time
gap to free the memory of the parent private data structure then
a memory leak of the part filled netdev buffer memory will occur.
Therefore, create a new function asix_rx_fixup_common_free() to
free the memory of the netdev buffer and add a call to
asix_rx_fixup_common_free() from inside ax88772_unbind().
Consequently when an unbind occurs part way through receiving
an Ethernet frame, the netdev buffer memory that is holding part
of the received Ethernet frame will now be freed.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dean Jenkins [Mon, 7 Aug 2017 08:50:15 +0000 (09:50 +0100)]
asix: Ensure asix_rx_fixup_info members are all reset
There is a risk that the members of the structure asix_rx_fixup_info
become unsynchronised leading to the possibility of a malfunction.
For example, rx->split_head was not being set to false after an
error was detected so potentially could cause a malformed 32-bit
Data header word to be formed.
Therefore add function reset_asix_rx_fixup_info() to reset all the
members of asix_rx_fixup_info so that future processing will start
with known initial conditions.
Also, if (skb->len != offset) becomes true then call
reset_asix_rx_fixup_info() so that the processing of the next URB
starts with known initial conditions. Without the call, the check
does nothing which potentially could lead to a malfunction
when the next URB is processed.
In addition, for robustness, call reset_asix_rx_fixup_info() before
every error path's "return 0". This ensures that the next URB is
processed from known initial conditions.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dean Jenkins [Mon, 7 Aug 2017 08:50:14 +0000 (09:50 +0100)]
asix: Add rx->ax_skb = NULL after usbnet_skb_return()
In asix_rx_fixup_internal() there is a risk that rx->ax_skb gets
reused after passing the Ethernet frame into the network stack via
usbnet_skb_return().
The risks include:
a) asynchronously freeing rx->ax_skb after passing the netdev buffer
to the NAPI layer which might corrupt the backlog queue.
b) erroneously reusing rx->ax_skb such as calling skb_put_data() multiple
times which causes writing off the end of the netdev buffer.
Therefore add a defensive rx->ax_skb = NULL after usbnet_skb_return()
so that it is not possible to free rx->ax_skb or to apply
skb_put_data() too many times.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Richter [Mon, 7 Aug 2017 08:16:36 +0000 (10:16 +0200)]
bpf: fix selftest/bpf/test_pkt_md_access on s390x
Commit
18f3d6be6be1 ("selftests/bpf: Add test cases to test narrower ctx field loads")
introduced new eBPF test cases. One of them (test_pkt_md_access.c)
fails on s390x. The BPF verifier error message is:
[root@s8360046 bpf]# ./test_progs
test_pkt_access:PASS:ipv4 349 nsec
test_pkt_access:PASS:ipv6 212 nsec
[....]
libbpf: load bpf program failed: Permission denied
libbpf: -- BEGIN DUMP LOG ---
libbpf:
0: (71) r2 = *(u8 *)(r1 +0)
invalid bpf_context access off=0 size=1
libbpf: -- END LOG --
libbpf: failed to load program 'test1'
libbpf: failed to load object './test_pkt_md_access.o'
Summary: 29 PASSED, 1 FAILED
[root@s8360046 bpf]#
This is caused by a byte endianness issue. S390x is a big endian
architecture. Pointer access to the lowest byte or halfword of a
four byte value need to add an offset.
On little endian architectures this offset is not needed.
Fix this and use the same approach as the originator used for other files
(for example test_verifier.c) in his original commit.
With this fix the test program test_progs succeeds on s390x:
[root@s8360046 bpf]# ./test_progs
test_pkt_access:PASS:ipv4 236 nsec
test_pkt_access:PASS:ipv6 217 nsec
test_xdp:PASS:ipv4 3624 nsec
test_xdp:PASS:ipv6 1722 nsec
test_l4lb:PASS:ipv4 926 nsec
test_l4lb:PASS:ipv6 1322 nsec
test_tcp_estats:PASS: 0 nsec
test_bpf_obj_id:PASS:get-fd-by-notexist-prog-id 0 nsec
test_bpf_obj_id:PASS:get-fd-by-notexist-map-id 0 nsec
test_bpf_obj_id:PASS:get-prog-info(fd) 0 nsec
test_bpf_obj_id:PASS:get-map-info(fd) 0 nsec
test_bpf_obj_id:PASS:get-prog-info(fd) 0 nsec
test_bpf_obj_id:PASS:get-map-info(fd) 0 nsec
test_bpf_obj_id:PASS:get-prog-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-prog-info(next_id->fd) 0 nsec
test_bpf_obj_id:PASS:get-prog-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-prog-info(next_id->fd) 0 nsec
test_bpf_obj_id:PASS:check total prog id found by get_next_id 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:check get-map-info(next_id->fd) 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:check get-map-info(next_id->fd) 0 nsec
test_bpf_obj_id:PASS:check total map id found by get_next_id 0 nsec
test_pkt_md_access:PASS: 277 nsec
Summary: 30 PASSED, 0 FAILED
[root@s8360046 bpf]#
Fixes:
18f3d6be6be1 ("selftests/bpf: Add test cases to test narrower ctx field loads")
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ludovic Desroches [Sun, 6 Aug 2017 14:00:05 +0000 (16:00 +0200)]
pinctrl: generic: update references to Documentation/pinctrl.txt
Update deprecated references to Documentation/pinctrl.txt since it has been
moved to Documentation/driver-api/pinctl.rst.
Signed-off-by: Ludovic Desroches <ludovic.desroches@o2linux.fr>
Fixes:
5a9b73832e9e ("pinctrl.txt: move it to the driver-api book")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andy Shevchenko [Fri, 4 Aug 2017 16:26:34 +0000 (19:26 +0300)]
pinctrl: intel: merrifield: Correct UART pin lists
UART pin lists consist GPIO numbers which is simply wrong.
Replace it by pin numbers.
Fixes:
4e80c8f50574 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Gregory CLEMENT [Tue, 1 Aug 2017 15:57:20 +0000 (17:57 +0200)]
pinctrl: armada-37xx: Fix number of pin in south bridge
On the south bridge we have pin from to 29, so it gives 30 pins (and not
29).
Without this patch the kernel complain with the following traces:
cat /sys/kernel/debug/pinctrl/
d0018800.pinctrl/pingroups
[ 154.530205] armada-37xx-pinctrl
d0018800.pinctrl: failed to get pin(29) name
[ 154.537567] ------------[ cut here ]------------
[ 154.542348] WARNING: CPU: 1 PID: 1347 at /home/gclement/open/kernel/marvell-mainline-linux/drivers/pinctrl/core.c:1610 pinctrl_groups_show+0x15c/0x1a0
[ 154.555918] Modules linked in:
[ 154.558890] CPU: 1 PID: 1347 Comm: cat Tainted: G W
4.13.0-rc1-00001-g19e1b9fa219d #525
[ 154.568316] Hardware name: Marvell Armada 3720 Development Board DB-
88F3720-DDR3 (DT)
[ 154.576311] task:
ffff80001d32d100 task.stack:
ffff80001bdc0000
[ 154.583048] PC is at pinctrl_groups_show+0x15c/0x1a0
[ 154.587816] LR is at pinctrl_groups_show+0x148/0x1a0
[ 154.592847] pc : [<
ffff0000083e3adc>] lr : [<
ffff0000083e3ac8>] pstate:
00000145
[ 154.600840] sp :
ffff80001bdc3c80
[ 154.604255] x29:
ffff80001bdc3c80 x28:
00000000f7750000
[ 154.609825] x27:
ffff80001d05d198 x26:
0000000000000009
[ 154.615224] x25:
ffff0000089ead20 x24:
0000000000000002
[ 154.620705] x23:
ffff000008c8e1d0 x22:
ffff80001be55700
[ 154.626187] x21:
ffff80001d05d100 x20:
0000000000000005
[ 154.631667] x19:
0000000000000006 x18:
0000000000000010
[ 154.637238] x17:
0000000000000000 x16:
ffff0000081fc4b8
[ 154.642726] x15:
0000000000000006 x14:
ffff0000899e537f
[ 154.648214] x13:
ffff0000099e538d x12:
206f742064656c69
[ 154.653613] x11:
6166203a6c727463 x10:
0000000005f5e0ff
[ 154.659094] x9 :
ffff80001bdc38c0 x8 :
286e697020746567
[ 154.664576] x7 :
ffff000008551870 x6 :
000000000000011b
[ 154.670146] x5 :
0000000000000000 x4 :
0000000000000000
[ 154.675544] x3 :
0000000000000000 x2 :
0000000000000000
[ 154.681025] x1 :
ffff000008c8e1d0 x0 :
ffff80001be55700
[ 154.686507] Call trace:
[ 154.688668] Exception stack(0xffff80001bdc3ab0 to 0xffff80001bdc3be0)
[ 154.695224] 3aa0:
0000000000000006 0001000000000000
[ 154.703310] 3ac0:
ffff80001bdc3c80 ffff0000083e3adc ffff80001bdc3bb0 00000000ffffffd8
[ 154.711304] 3ae0:
4554535953425553 6f6674616c703d4d 4349564544006d72 6674616c702b3d45
[ 154.719478] 3b00:
313030643a6d726f 6e69702e30303838 ffff80006c727463 ffff0000089635d8
[ 154.727562] 3b20:
ffff80001d1ca0cb ffff000008af0fa4 ffff80001bdc3b40 ffff000008c8e1dc
[ 154.735648] 3b40:
ffff80001bdc3bc0 ffff000008223174 ffff80001be55700 ffff000008c8e1d0
[ 154.743731] 3b60:
0000000000000000 0000000000000000 0000000000000000 0000000000000000
[ 154.752354] 3b80:
000000000000011b ffff000008551870 286e697020746567 ffff80001bdc38c0
[ 154.760446] 3ba0:
0000000005f5e0ff 6166203a6c727463 206f742064656c69 ffff0000099e538d
[ 154.767910] 3bc0:
ffff0000899e537f 0000000000000006 ffff0000081fc4b8 0000000000000000
[ 154.776085] [<
ffff0000083e3adc>] pinctrl_groups_show+0x15c/0x1a0
[ 154.782823] [<
ffff000008222abc>] seq_read+0x184/0x460
[ 154.787505] [<
ffff000008344120>] full_proxy_read+0x60/0xa8
[ 154.793431] [<
ffff0000081f9bec>] __vfs_read+0x1c/0x110
[ 154.799001] [<
ffff0000081faff4>] vfs_read+0x84/0x140
[ 154.803860] [<
ffff0000081fc4fc>] SyS_read+0x44/0xa0
[ 154.808983] [<
ffff000008082f30>] el0_svc_naked+0x24/0x28
[ 154.814459] ---[ end trace
4cbb00a92d616b95 ]---
Cc: stable@vger.kernel.org
Fixes:
87466ccd9401 ("pinctrl: armada-37xx: Add pin controller support
for Armada 37xx")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Gregory CLEMENT [Tue, 1 Aug 2017 15:57:19 +0000 (17:57 +0200)]
pinctrl: armada-37xx: Fix the pin 23 on south bridge
Pin 23 on South bridge does not belong to the rgmii group. It belongs to
a separate group which can have 3 functions.
Due to this the fix also have to update the way the functions are
managed. Until now each groups used NB_FUNCS(which was 2) functions. For
the mpp23, 3 functions are available but it is the only group which needs
it, so on the loop involving NB_FUNCS an extra test was added to handle
only the functions added.
The bug was visible with the merge of the commit
07d065abf93d "arm64:
dts: marvell: armada-3720-db: Add vqmmc regulator for SD slot", the gpio
regulator used the gpio 23, due to this the whole rgmii group was setup
to gpio which broke the Ethernet support on the Armada 3720 DB
board. Thanks to this patch, the UHS SD cards (which need the vqmmc)
_and_ the Ethernet work again.
Cc: stable@vger.kernel.org
Fixes:
87466ccd9401 ("pinctrl: armada-37xx: Add pin controller support
for Armada 37xx")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
stephen hemminger [Fri, 4 Aug 2017 00:13:54 +0000 (17:13 -0700)]
netvsc: fix race on sub channel creation
The existing sub channel code did not wait for all the sub-channels
to completely initialize. This could lead to race causing crash
in napi_netif_del() from bad list. The existing code would send
an init message, then wait only for the initial response that
the init message was received. It thought it was waiting for
sub channels but really the init response did the wakeup.
The new code keeps track of the number of open channels and
waits until that many are open.
Other issues here were:
* host might return less sub-channels than was requested.
* the new init status is not valid until after init was completed.
Fixes:
b3e6b82a0099 ("hv_netvsc: Wait for sub-channels to be processed during probe")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 7 Aug 2017 01:44:49 +0000 (18:44 -0700)]
Linux 4.13-rc4
Linus Torvalds [Sun, 6 Aug 2017 23:11:34 +0000 (16:11 -0700)]
Merge tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fix from Darren Hart:
"Fix loop preventing some platforms from waking up via the power button
in s2idle:
- intel-vbtn: match power button on press rather than release"
* tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: intel-vbtn: match power button on press rather than release
Linus Torvalds [Sun, 6 Aug 2017 19:31:17 +0000 (12:31 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"A large number of ext4 bug fixes and cleanups for v4.13"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix copy paste error in ext4_swap_extents()
ext4: fix overflow caused by missing cast in ext4_resize_fs()
ext4, project: expand inode extra size if possible
ext4: cleanup ext4_expand_extra_isize_ea()
ext4: restructure ext4_expand_extra_isize
ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
ext4: make xattr inode reads faster
ext4: inplace xattr block update fails to deduplicate blocks
ext4: remove unused mode parameter
ext4: fix warning about stack corruption
ext4: fix dir_nlink behaviour
ext4: silence array overflow warning
ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize
ext4: release discard bio after sending discard commands
ext4: convert swap_inode_data() over to use swap() on most of the fields
ext4: error should be cleared if ea_inode isn't added to the cache
ext4: Don't clear SGID when inheriting ACLs
ext4: preserve i_mode if __ext4_set_acl() fails
ext4: remove unused metadata accounting variables
ext4: correct comment references to ext4_ext_direct_IO()
Linus Torvalds [Sun, 6 Aug 2017 18:52:01 +0000 (11:52 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"This fixes two build issues for ralink platforms, both due to missing
#includes which used to be included indirectly via other headers"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ralink: mt7620: Add missing header
MIPS: ralink: Fix build error due to missing header
Dmitry V. Levin [Sat, 5 Aug 2017 20:00:50 +0000 (23:00 +0300)]
Fix compat_sys_sigpending breakage
The latest change of compat_sys_sigpending in commit
8f13621abced
("sigpending(): move compat to native") has broken it in two ways.
First, it tries to write 4 bytes more than userspace expects:
sizeof(old_sigset_t) == sizeof(long) == 8 instead of
sizeof(compat_old_sigset_t) == sizeof(u32) == 4.
Second, on big endian architectures these bytes are being written in the
wrong order.
This bug was found by strace test suite.
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Inspired-by: Eugene Syromyatnikov <evgsyr@gmail.com>
Fixes:
8f13621abced ("sigpending(): move compat to native")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Maninder Singh [Sun, 6 Aug 2017 05:33:07 +0000 (01:33 -0400)]
ext4: fix copy paste error in ext4_swap_extents()
This bug was found by a static code checker tool for copy paste
problems.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Jerry Lee [Sun, 6 Aug 2017 05:18:31 +0000 (01:18 -0400)]
ext4: fix overflow caused by missing cast in ext4_resize_fs()
On a 32-bit platform, the value of n_blcoks_count may be wrong during
the file system is resized to size larger than 2^32 blocks. This may
caused the superblock being corrupted with zero blocks count.
Fixes:
1c6bd7173d66
Signed-off-by: Jerry Lee <jerrylee@qnap.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org # 3.7+
Miao Xie [Sun, 6 Aug 2017 05:00:49 +0000 (01:00 -0400)]
ext4, project: expand inode extra size if possible
When upgrading from old format, try to set project id
to old file first time, it will return EOVERFLOW, but if
that file is dirtied(touch etc), changing project id will
be allowed, this might be confusing for users, we could
try to expand @i_extra_isize here too.
Reported-by: Zhang Yi <yi.zhang@huawei.com>
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Wang Shilong <wshilong@ddn.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Miao Xie [Sun, 6 Aug 2017 04:55:48 +0000 (00:55 -0400)]
ext4: cleanup ext4_expand_extra_isize_ea()
Clean up some goto statement, make ext4_expand_extra_isize_ea() clearer.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
Miao Xie [Sun, 6 Aug 2017 04:40:01 +0000 (00:40 -0400)]
ext4: restructure ext4_expand_extra_isize
Current ext4_expand_extra_isize just tries to expand extra isize, if
someone is holding xattr lock or some check fails, it will give up.
So rename its name to ext4_try_to_expand_extra_isize.
Besides that, we clean up unnecessary check and move some relative checks
into it.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
Miao Xie [Sun, 6 Aug 2017 04:27:38 +0000 (00:27 -0400)]
ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
We should avoid the contention between the i_extra_isize update and
the inline data insertion, so move the xattr trylock in front of
i_extra_isize update.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
Tahsin Erdogan [Sun, 6 Aug 2017 04:07:01 +0000 (00:07 -0400)]
ext4: make xattr inode reads faster
ext4_xattr_inode_read() currently reads each block sequentially while
waiting for io operation to complete before moving on to the next
block. This prevents request merging in block layer.
Add a ext4_bread_batch() function that starts reads for all blocks
then optionally waits for them to complete. A similar logic is used
in ext4_find_entry(), so update that code to use the new function.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Tahsin Erdogan [Sun, 6 Aug 2017 02:41:42 +0000 (22:41 -0400)]
ext4: inplace xattr block update fails to deduplicate blocks
When an xattr block has a single reference, block is updated inplace
and it is reinserted to the cache. Later, a cache lookup is performed
to see whether an existing block has the same contents. This cache
lookup will most of the time return the just inserted entry so
deduplication is not achieved.
Running the following test script will produce two xattr blocks which
can be observed in "File ACL: " line of debugfs output:
mke2fs -b 1024 -I 128 -F -O extent /dev/sdb 1G
mount /dev/sdb /mnt/sdb
touch /mnt/sdb/{x,y}
setfattr -n user.1 -v aaa /mnt/sdb/x
setfattr -n user.2 -v bbb /mnt/sdb/x
setfattr -n user.1 -v aaa /mnt/sdb/y
setfattr -n user.2 -v bbb /mnt/sdb/y
debugfs -R 'stat x' /dev/sdb | cat
debugfs -R 'stat y' /dev/sdb | cat
This patch defers the reinsertion to the cache so that we can locate
other blocks with the same contents.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Tahsin Erdogan [Sun, 6 Aug 2017 02:15:45 +0000 (22:15 -0400)]
ext4: remove unused mode parameter
ext4_alloc_file_blocks() does not use its mode parameter. Remove it.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Arnd Bergmann [Sun, 6 Aug 2017 01:57:46 +0000 (21:57 -0400)]
ext4: fix warning about stack corruption
After commit
62d1034f53e3 ("fortify: use WARN instead of BUG for now"),
we get a warning about possible stack overflow from a memcpy that
was not strictly bounded to the size of the local variable:
inlined from 'ext4_mb_seq_groups_show' at fs/ext4/mballoc.c:2322:2:
include/linux/string.h:309:9: error: '__builtin_memcpy': writing between 161 and 1116 bytes into a region of size 160 overflows the destination [-Werror=stringop-overflow=]
We actually had a bug here that would have been found by the warning,
but it was already fixed last year in commit
30a9d7afe70e ("ext4: fix
stack memory corruption with 64k block size").
This replaces the fixed-length structure on the stack with a variable-length
structure, using the correct upper bound that tells the compiler that
everything is really fine here. I also change the loop count to check
for the same upper bound for consistency, but the existing code is
already correct here.
Note that while clang won't allow certain kinds of variable-length arrays
in structures, this particular instance is fine, as the array is at the
end of the structure, and the size is strictly bounded.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Andreas Dilger [Sat, 5 Aug 2017 23:47:34 +0000 (19:47 -0400)]
ext4: fix dir_nlink behaviour
The dir_nlink feature has been enabled by default for new ext4
filesystems since e2fsprogs-1.41 in 2008, and was automatically
enabled by the kernel for older ext4 filesystems since the
dir_nlink feature was added with ext4 in kernel 2.6.28+ when
the subdirectory count exceeded EXT4_LINK_MAX-1.
Automatically adding the file system features such as dir_nlink is
generally frowned upon, since it could cause the file system to not be
mountable on older kernel, thus preventing the administrator from
rolling back to an older kernel if necessary.
In this case, the administrator might also want to disable the feature
because glibc's fts_read() function does not correctly optimize
directory traversal for directories that use st_nlinks field of 1 to
indicate that the number of links in the directory are not tracked by
the file system, and could fail to traverse the full directory
hierarchy. Fortunately, in the past ten years very few users have
complained about incomplete file system traversal by glibc's
fts_read().
This commit also changes ext4_inc_count() to allow i_nlinks to reach
the full EXT4_LINK_MAX links on the parent directory (including "."
and "..") before changing i_links_count to be 1.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196405
Signed-off-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Dan Carpenter [Sat, 5 Aug 2017 23:00:31 +0000 (19:00 -0400)]
ext4: silence array overflow warning
I get a static checker warning:
fs/ext4/ext4.h:3091 ext4_set_de_type()
error: buffer overflow 'ext4_type_by_mode' 15 <= 15
It seems unlikely that we would hit this read overflow in real life, but
it's also simple enough to make the array 16 bytes instead of 15.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Jan Kara [Sat, 5 Aug 2017 21:43:24 +0000 (17:43 -0400)]
ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize
ext4_find_unwritten_pgoff() does not properly handle a situation when
starting index is in the middle of a page and blocksize < pagesize. The
following command shows the bug on filesystem with 1k blocksize:
xfs_io -f -c "falloc 0 4k" \
-c "pwrite 1k 1k" \
-c "pwrite 3k 1k" \
-c "seek -a -r 0" foo
In this example, neither lseek(fd, 1024, SEEK_HOLE) nor lseek(fd, 2048,
SEEK_DATA) will return the correct result.
Fix the problem by neglecting buffers in a page before starting offset.
Reported-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
CC: stable@vger.kernel.org # 3.8+
Mario Limonciello [Fri, 4 Aug 2017 17:00:06 +0000 (12:00 -0500)]
platform/x86: intel-vbtn: match power button on press rather than release
This fixes a problem where the system gets stuck in a loop
unable to wakeup via power button in s2idle.
The problem happens because:
- press power button:
- system emits 0xc0 (power press), event ignored
- system emits 0xc1 (power release), event processed,
emited as KEY_POWER
- set wakeup_mode to true
- system goes to s2idle
- press power button
- system emits 0xc0 (power press), wakeup_mode is true,
system wakes
- system emits 0xc1 (power release), event processed,
emited as KEY_POWER
- system goes to s2idle again
To avoid this situation, process the presses (which matches what
intel-hid does too).
Verified on an Dell XPS 9365
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Linus Torvalds [Sat, 5 Aug 2017 21:09:26 +0000 (14:09 -0700)]
Merge tag 'media/v4.13-2' of git://git./linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"This series is larger than I would like to submit for -rc4. My
original intent were to sent it to either -rc2 or -rc3. Unfortunately,
due to my vacations, I got a lot of pending stuff after my return, and
had to do some biz trips, with prevented me to send this earlier.
Several fixes:
- some fixes at atomisp staging driver
- several gcc 7 warning fixes
- cleanup media SVG files, in order to fix PDF build on some distros
- fix random Kconfig build of venus driver
- some fixes for the venus driver
- some changes from semaphone to mutex in ngene's driver
- some locking fixes at dib0700 driver
- several fixes on ngene's driver and frontends to make it properly
support some new boards added on Kernel 4.13
- some fixes to CEC drivers
- omap_vout: vrfb: convert to dmaengine
- docs-rst: document EBUSY for VIDIOC_S_FMT
Please notice that the big diffstat changes here are at the SVG files.
Visually, the images look the same, but the file size is now a lot
smaller than before, and they don't use some XML tags that would cause
them to be badly parsed by some ImageMagick versions, or to require a
lot of memory by TeTex, with would break PDF output on some
distributions"
* tag 'media/v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (68 commits)
media: atomisp2: array underflow in imx_enum_frame_size()
media: atomisp2: array underflow in ap1302_enum_frame_size()
media: atomisp2: Array underflow in atomisp_enum_input()
media: platform: davinci: drop VPFE_CMD_S_CCDC_RAW_PARAMS
media: platform: davinci: return -EINVAL for VPFE_CMD_S_CCDC_RAW_PARAMS ioctl
media: venus: don't abuse dma_alloc for non-DMA allocations
media: venus: hfi: fix error handling in hfi_sys_init_done()
media: venus: fix compile-test build on non-qcom ARM platform
media: venus: mark PM functions as __maybe_unused
media: cec-notifier: small improvements
media: pulse8-cec: persistent_config should be off by default
media: cec: cec_transmit_attempt_done: ignore CEC_TX_STATUS_MAX_RETRIES
media: staging: atomisp: array underflow in ioctl
media: lirc: LIRC_GET_REC_RESOLUTION should return microseconds
media: svg: avoid too long lines
media: svg files: simplify files
media: selection.svg: simplify the SVG file
media: vimc: set id_table for platform drivers
media: staging: atomisp: disable warnings with cc-disable-warning
media: davinci: variable 'common' set but not used
...
Daeho Jeong [Sat, 5 Aug 2017 17:11:57 +0000 (13:11 -0400)]
ext4: release discard bio after sending discard commands
We've changed the discard command handling into parallel manner.
But, in this change, I forgot decreasing the usage count of the bio
which was used to send discard request. I'm sorry about that.
Fixes:
a015434480dc ("ext4: send parallel discards on commit completions")
Signed-off-by: Daeho Jeong <daeho.jeong@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Linus Torvalds [Sat, 5 Aug 2017 13:55:13 +0000 (06:55 -0700)]
Merge tag 'gpio-v4.13-2' of git://git./linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- LP87565: set the proper output level for direction_output.
- stm32: fix the kernel build by selecting the hierarchical irqdomain
symbol properly - this happens to be done in the pin control
framework but whatever, it had dependencies to GPIO so we need to
apply it here.
- Select the hierarchical IRQ domain also for Xgene.
- Fix wakeups to work on MXC.
- Fix up the device tree binding on Exar that went astray, also add the
right bindings.
- Fix the unwanted events for edges from the library.
- Fix the unbalanced chanined IRQ on the Tegra.
* tag 'gpio-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tegra: fix unbalanced chained_irq_enter/exit
gpiolib: skip unwanted events, don't convert them to opposite edge
gpio: exar: Use correct property prefix and document bindings
gpio: gpio-mxc: Fix: higher 16 GPIOs usable as wake source
gpio: xgene-sb: select IRQ_DOMAIN_HIERARCHY
pinctrl: stm32: select IRQ_DOMAIN_HIERARCHY instead of depends on
gpio: lp87565: Set proper output level and direction for direction_output
MAINTAINERS: Add entry for Whiskey Cove PMIC GPIO driver
Brian Norris [Sat, 5 Aug 2017 01:42:37 +0000 (18:42 -0700)]
Merge tag 'nand/fixes-for-4.13-rc4' of git://git.infradead.org/l2-mtd into MTD
"""
This PR contains both core and drivers fixes for 4.13.
Core fixes:
- Fix data interface setup for ONFI NANDs that do not support the SET
FEATURES command
- Fix a kernel doc header
- Fix potential integer overflow when retrieving timing information
from the parameter page
- Fix wrong OOB layout for small page NANDs
Driver fixes:
- Fix potential division-by-zero bug
- Fix backward compat with old atmel-nand DT bindings
- Fix ->setup_data_interface() in the atmel NAND driver
"""
Linus Torvalds [Fri, 4 Aug 2017 23:45:29 +0000 (16:45 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of critical fixes for changes introduce this merge window.
- The TI sci_clk_get() API was pretty broken and nobody noticed.
- There were some CPUfreq crashes on C.H.I.P devices because we
failed to propagate rates up the clk tree.
- Also, the Intel Atom PMC clk driver needs to mark a clk critical if
the firmware has it enabled already so that audio doesn't get
killed on Baytrail.
- Gemini devices have a dead serial console because the reset control
usage in the serial driver assume one method of reset that gemini
doesn't support (this will be fixed in the next version in the
reset framework so this is the small fix for -rc series).
- Finally we have two rate calculation fixes, one for Exynos and one
for Meson SoCs, that fix rate inconsistencies"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: keystone: sci-clk: Fix sci_clk_get
clk: meson: mpll: fix mpll0 fractional part ignored
clk: samsung: exynos5420: The EPLL rate table corrections
clk: sunxi-ng: sun5i: Add clk_set_rate_parent to the CPU clock
clk: x86: Do not gate clocks enabled by the firmware
clk: gemini: Fix reset regression
Daniel Borkmann [Fri, 4 Aug 2017 20:24:41 +0000 (22:24 +0200)]
bpf: fix byte order test in test_verifier
We really must check with #if __BYTE_ORDER == XYZ instead of
just presence of #ifdef __LITTLE_ENDIAN. I noticed that when
actually running this on big endian machine, the latter test
resolves to true for user space, same for #ifdef __BIG_ENDIAN.
E.g., looking at endian.h from libc, both are also defined
there, so we really must test this against __BYTE_ORDER instead
for proper insns selection. For the kernel, such checks are
fine though e.g. see
13da9e200fe4 ("Revert "endian: #define
__BYTE_ORDER"") and
415586c9e6d3 ("UAPI: fix endianness conditionals
in M32R's asm/stat.h") for some more context, but not for
user space. Lets also make sure to properly include endian.h.
After that, suite passes for me:
./test_verifier: ELF 64-bit MSB executable, [...]
Linux foo 4.13.0-rc3+ #4 SMP Fri Aug 4 06:59:30 EDT 2017 s390x s390x s390x GNU/Linux
Before fix: Summary: 505 PASSED, 11 FAILED
After fix: Summary: 516 PASSED, 0 FAILED
Fixes:
18f3d6be6be1 ("selftests/bpf: Add test cases to test narrower ctx field loads")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 4 Aug 2017 22:18:27 +0000 (15:18 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- Yet another race with VM destruction plugged
- A set of small vgic fixes
x86:
- Preserve pending INIT
- RCU fixes in paravirtual async pf, VM teardown, and VMXOFF
emulation
- nVMX interrupt injection and dirty tracking fixes
- initialize to make UBSAN happy"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm/arm64: vgic: Use READ_ONCE fo cmpxchg
KVM: nVMX: Fix interrupt window request with "Acknowledge interrupt on exit"
KVM: nVMX: mark vmcs12 pages dirty on L2 exit
kvm: nVMX: don't flush VMCS12 during VMXOFF or VCPU teardown
KVM: nVMX: do not pin the VMCS12
KVM: avoid using rcu_dereference_protected
KVM: X86: init irq->level in kvm_pv_kick_cpu_op
KVM: X86: Fix loss of pending INIT due to race
KVM: async_pf: make rcu irq exit if not triggered from idle task
KVM: nVMX: fixes to nested virt interrupt injection
KVM: nVMX: do not fill vm_exit_intr_error_code in prepare_vmcs12
KVM: arm/arm64: Handle hva aging while destroying the vm
KVM: arm/arm64: PMU: Fix overflow interrupt injection
KVM: arm/arm64: Fix bug in advertising KVM_CAP_MSI_DEVID capability
Linus Torvalds [Fri, 4 Aug 2017 22:16:09 +0000 (15:16 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"The recent irq core changes unearthed API abuse in the HPET code,
which manifested itself in a suspend/resume regression.
The fix replaces the cruft with the proper function calls and cures
the regression"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hpet: Cure interface abuse in the resume path
Linus Torvalds [Fri, 4 Aug 2017 22:14:09 +0000 (15:14 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A single fix for a multiplication overflow in the timer code on 32bit
systems"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Fix overflow in get_next_timer_interrupt
Linus Torvalds [Fri, 4 Aug 2017 22:12:15 +0000 (15:12 -0700)]
Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This comes a bit later than I planned, and as a consequence is a
larger than it should be.
Most of the changes are devicetree fixes, across lots of platforms:
Renesas, Samsung Exynos, Marvell EBU, TI OMAP, Rockchips, Amlogic
Meson, Sigma Desings Tango, Allwinner SUNxi and TI Davinci.
Also across many platforms, I applied an older series of simple
randconfig build fixes. This includes making the CONFIG_MTD_XIP option
compile again, which had been broken for many years and probably has
not been missed, but it felt wrong to just remove it completely.
The only other changes are:
- We enable HWSPINLOCK in defconfig to get some Qualcomm boards to
work out of the box.
- A few regression fixes for Texas Instruments OMAP2+.
- A boot regression fix for the Renesas regulator quirk.
- A suspend/resume fix for Uniphier SoCs, fixing the resume of the
system bus"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: dts: tango4: Request RGMII RX and TX clock delays
bus: uniphier-system-bus: set up registers when resuming
ARM64: dts: marvell: armada-37xx: Fix the number of GPIO on south bridge
ARM: shmobile: rcar-gen2: Fix deadlock in regulator quirk
arm64: defconfig: enable missing HWSPINLOCK
ARM: pxa: select both FB and FB_W100 for eseries
ARM: ixp4xx: fix ioport_unmap definition
ARM: ep93xx: use ARM_PATCH_PHYS_VIRT correctly
ARM: mmp: mark usb_dma_mask as __maybe_unused
ARM: omap2: mark unused functions as __maybe_unused
ARM: omap1: avoid unused variable warning
ARM: sirf: mark sirfsoc_init_late as __maybe_unused
ARM: ixp4xx: use normal prototype for {read,write}s{b,w,l}
ARM: omap1/ams-delta: warn about failed regulator enable
ARM: rpc: rename RAM_SIZE macro
ARM: w90x900: normalize clk API
ARM: ep93xx: normalize clk API
ARM: dts: sun8i: a83t: Switch to CCU device tree binding macros
arm64: allwinner: sun50i-a64: Correct emac register size
ARM: dts: sunxi: h3/h5: Correct emac register size
...
Lukas Czerner [Thu, 3 Aug 2017 20:19:13 +0000 (13:19 -0700)]
xfs: Fix per-inode DAX flag inheritance
According to the commit that implemented per-inode DAX flag:
commit
58f88ca2df72 ("xfs: introduce per-inode DAX enablement")
the flag is supposed to act as "inherit flag".
Currently this only works in the situations where parent directory
already has a flag in di_flags set, otherwise inheritance does not
work. This is because setting the XFS_DIFLAG2_DAX flag is done in a
wrong branch designated for di_flags, not di_flags2.
Fix this by moving the code to branch designated for setting di_flags2,
which does test for flags in di_flags2.
Fixes:
58f88ca2df72 ("xfs: introduce per-inode DAX enablement")
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Jan Kara [Wed, 2 Aug 2017 19:37:16 +0000 (12:37 -0700)]
xfs: Fix leak of discard bio
The bio describing discard operation is allocated by
__blkdev_issue_discard() which returns us a reference to it. That
reference is never released and thus we leak this bio. Drop the bio
reference once it completes in xlog_discard_endio().
CC: stable@vger.kernel.org
Fixes:
4560e78f40cb55bd2ea8f1ef4001c5baa88531c7
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Linus Torvalds [Fri, 4 Aug 2017 19:11:48 +0000 (12:11 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are some more arm64 fixes for 4.13. The main one is the PTE race
with the hardware walker, but there are a couple of other things too.
- Report correct timer frequency to userspace when trapping
CNTFRQ_EL0
- Fix race with hardware page table updates when updating access
flags
- Silence clang overflow warning in VA_START and PAGE_OFFSET
calculations"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: avoid overflow in VA_START and PAGE_OFFSET
arm64: Fix potential race with hardware DBM in ptep_set_access_flags()
arm64: Use arch_timer_get_rate when trapping CNTFRQ_EL0