loop: Refactor loop_set_status() size calculation

figure_loop_size() calculates the loop size based on the passed in
parameters, but at the same time it updates the offset and sizelimit
parameters in the loop device configuration. That is a somewhat
unexpected side effect of a function with this name, and it is only only
needed by one of the two callers of this function - loop_set_status().

Move the lo_offset and lo_sizelimit assignment back into loop_set_status(),
and use the newly factored out functions to validate and apply the newly
calculated size. This allows us to get rid of figure_loop_size() in a
follow-up commit.

Signed-off-by: Martijn Coenen <maco@android.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

loop: Switch to set_capacity_revalidate_and_notify()

This was recently added to block/genhd.c, and takes care of both
updating the capacity and notifying userspace of the new size.

Signed-off-by: Martijn Coenen <maco@android.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

loop: Factor out setting loop device size

This code is used repeatedly.

Signed-off-by: Martijn Coenen <maco@android.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

loop: Remove sector_t truncation checks

sector_t is now always u64, so we don't need to check for truncation.

Signed-off-by: Martijn Coenen <maco@android.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

loop: Call loop_config_discard() only after new config is applied

loop_set_status() calls loop_config_discard() to configure discard for
the loop device; however, the discard configuration depends on whether
the loop device uses encryption, and when we call it the encryption
configuration has not been updated yet. Move the call down so we apply
the correct discard configuration based on the new configuration.

Signed-off-by: Martijn Coenen <maco@android.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bob Liu <bob.liu@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block/swim3: use set_current_state macro

Use set_current_state macro instead of current->state = TASK_RUNNING.

Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Merge branch 'md-next' of git://git./linux/kernel/git/song/md into for-5.8/drivers

Pull MD changes from Song.

* 'md-next' of git://git.kernel.org/pub/scm/linux/kernel/git/song/md:
  md/raid1: Replace zero-length array with flexible-array
  md: add a newline when printing parameter 'start_ro' by sysfs
  md: stop using ->queuedata
  md/raid1: release pending accounting for an I/O only after write-behind is also finished
  md: remove redundant memalloc scope API usage
  raid5: update code comment of scribble_alloc()
  raid5: remove gfp flags from scribble_alloc()
  md: use memalloc scope APIs in mddev_suspend()/mddev_resume()
  md: remove the extra line for ->hot_add_disk
  md: flush md_rdev_misc_wq for HOT_ADD_DISK case
  md: don't flush workqueue unconditionally in md_open
  md: add new workqueue for delete rdev
  md: add checkings before flush md_misc_wq

md/raid1: Replace zero-length array with flexible-array

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Song Liu <songliubraving@fb.com>

md: add a newline when printing parameter 'start_ro' by sysfs

Add a missing newline when printing module parameter 'start_ro' by
sysfs.

Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

md: stop using ->queuedata

Pointer to mddev is already available in private_data.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Song Liu <songliubraving@fb.com>

md/raid1: release pending accounting for an I/O only after write-behind is also finished

When using RAID1 and write-behind, md can deadlock when errors occur. With
write-behind, r1bio structs can be accounted by raid1 as queued but not
counted as pending. The pending count is dropped when the original bio is
returned complete but write-behind for the r1bio may still be active.

This breaks the accounting used in some conditions to know when the raid1
md device has reached an idle state. It can result in calls to
freeze_array deadlocking. freeze_array will never complete from a negative
"unqueued" value being calculated due to a queued count larger than the
pending count.

To properly account for write-behind, move the call to allow_barrier from
call_bio_endio to raid_end_bio_io. When using write-behind, md can call
call_bio_endio before all write-behind I/O is complete. Using
raid_end_bio_io for the point to call allow_barrier will release the
pending count at a point where all I/O for an r1bio, even write-behind, is
done.

Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

md: remove redundant memalloc scope API usage

In mddev_create_serial_pool(), memalloc scope APIs memalloc_noio_save()
and memalloc_noio_restore() are used when allocating memory by calling
mempool_create_kmalloc_pool(). After adding the memalloc scope APIs in
raid array suspend context, it is unncessary to explicitly call them
around mempool_create_kmalloc_pool() any longer.

This patch removes the redundant memalloc scope APIs in
mddev_create_serial_pool().

Signed-off-by: Coly Li <colyli@suse.de>
Cc: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

raid5: update code comment of scribble_alloc()

Code comments of scribble_alloc() is outdated for a while. This patch
update the comments in function header for the new parameter list.

Suggested-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Song Liu <songliubraving@fb.com>

raid5: remove gfp flags from scribble_alloc()

Using GFP_NOIO flag to call scribble_alloc() from resize_chunk() does
not have the expected behavior. kvmalloc_array() inside scribble_alloc()
which receives the GFP_NOIO flag will eventually call kmalloc_node() to
allocate physically continuous pages.

Now we have memalloc scope APIs in mddev_suspend()/mddev_resume() to
prevent memory reclaim I/Os during raid array suspend context, calling
to kvmalloc_array() with GFP_KERNEL flag may avoid deadlock of recursive
I/O as expected.

This patch removes the useless gfp flags from parameters list of
scribble_alloc(), and call kvmalloc_array() with GFP_KERNEL flag. The
incorrect GFP_NOIO flag does not exist anymore.

Fixes: b330e6a49dc3 ("md: convert to kvmalloc")
Suggested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Song Liu <songliubraving@fb.com>

md: use memalloc scope APIs in mddev_suspend()/mddev_resume()

In raid5.c:resize_chunk(), scribble_alloc() is called with GFP_NOIO
flag, then it is sent into kvmalloc_array() inside scribble_alloc().

The problem is kvmalloc_array() eventually calls kvmalloc_node() which
does not accept non GFP_KERNEL compatible flag like GFP_NOIO, then
kmalloc_node() is called indeed to allocate physically continuous
pages. When system memory is under heavy pressure, and the requesting
size is large, there is high probability that allocating continueous
pages will fail.

But simply using GFP_KERNEL flag to call kvmalloc_array() is also
progblematic. In the code path where scribble_alloc() is called, the
raid array is suspended, if kvmalloc_node() triggers memory reclaim I/Os
and such I/Os go back to the suspend raid array, deadlock will happen.

What is desired here is to allocate non-physically (a.k.a virtually)
continuous pages and avoid memory reclaim I/Os. Michal Hocko suggests
to use the mmealloc sceope APIs to restrict memory reclaim I/O in
allocating context, specifically to call memalloc_noio_save() when
suspend the raid array and to call memalloc_noio_restore() when
resume the raid array.

This patch adds the memalloc scope APIs in mddev_suspend() and
mddev_resume(), to restrict memory reclaim I/Os during the raid array
is suspended. The benifit of adding the memalloc scope API in the
unified entry point mddev_suspend()/mddev_resume() is, no matter which
md raid array type (personality), we are sure the deadlock by recursive
memory reclaim I/O won't happen on the suspending context.

Please notice that the memalloc scope APIs only take effect on the raid
array suspending context, if the memory allocation is from another new
created kthread after raid array suspended, the recursive memory reclaim
I/Os won't be restricted. The mddev_suspend()/mddev_resume() entries are
used for the critical section where the raid metadata is modifying,
creating a kthread to allocate memory inside the critical section is
queer and very probably being buggy.

Fixes: b330e6a49dc3 ("md: convert to kvmalloc")
Suggested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Song Liu <songliubraving@fb.com>

md: remove the extra line for ->hot_add_disk

It is not not necessary to add a newline for them since they don't exceed
80 characters, and it is not intutive to distinguish ->hot_add_disk() from
hot_add_disk() too.

Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

md: flush md_rdev_misc_wq for HOT_ADD_DISK case

Since rdev->kobj is removed asynchronously, it is possible that the
rdev->kobj still exists when try to add the rdev again after rdev
is removed. But this path md_ioctl (HOT_ADD_DISK) -> hot_add_disk
-> bind_rdev_to_array missed it.

Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

md: don't flush workqueue unconditionally in md_open

We need to check mddev->del_work before flush workqueu since the purpose
of flush is to ensure the previous md is disappeared. Otherwise the similar
deadlock appeared if LOCKDEP is enabled, it is due to md_open holds the
bdev->bd_mutex before flush workqueue.

kernel: [  154.522645] ======================================================
kernel: [  154.522647] WARNING: possible circular locking dependency detected
kernel: [  154.522650] 5.6.0-rc7-lp151.27-default #25 Tainted: G           O
kernel: [  154.522651] ------------------------------------------------------
kernel: [  154.522653] mdadm/2482 is trying to acquire lock:
kernel: [  154.522655] ffff888078529128 ((wq_completion)md_misc){+.+.}, at: flush_workqueue+0x84/0x4b0
kernel: [  154.522673]
kernel: [  154.522673] but task is already holding lock:
kernel: [  154.522675] ffff88804efa9338 (&bdev->bd_mutex){+.+.}, at: __blkdev_get+0x79/0x590
kernel: [  154.522691]
kernel: [  154.522691] which lock already depends on the new lock.
kernel: [  154.522691]
kernel: [  154.522694]
kernel: [  154.522694] the existing dependency chain (in reverse order) is:
kernel: [  154.522696]
kernel: [  154.522696] -> #4 (&bdev->bd_mutex){+.+.}:
kernel: [  154.522704]        __mutex_lock+0x87/0x950
kernel: [  154.522706]        __blkdev_get+0x79/0x590
kernel: [  154.522708]        blkdev_get+0x65/0x140
kernel: [  154.522709]        blkdev_get_by_dev+0x2f/0x40
kernel: [  154.522716]        lock_rdev+0x3d/0x90 [md_mod]
kernel: [  154.522719]        md_import_device+0xd6/0x1b0 [md_mod]
kernel: [  154.522723]        new_dev_store+0x15e/0x210 [md_mod]
kernel: [  154.522728]        md_attr_store+0x7a/0xc0 [md_mod]
kernel: [  154.522732]        kernfs_fop_write+0x117/0x1b0
kernel: [  154.522735]        vfs_write+0xad/0x1a0
kernel: [  154.522737]        ksys_write+0xa4/0xe0
kernel: [  154.522745]        do_syscall_64+0x64/0x2b0
kernel: [  154.522748]        entry_SYSCALL_64_after_hwframe+0x49/0xbe
kernel: [  154.522749]
kernel: [  154.522749] -> #3 (&mddev->reconfig_mutex){+.+.}:
kernel: [  154.522752]        __mutex_lock+0x87/0x950
kernel: [  154.522756]        new_dev_store+0xc9/0x210 [md_mod]
kernel: [  154.522759]        md_attr_store+0x7a/0xc0 [md_mod]
kernel: [  154.522761]        kernfs_fop_write+0x117/0x1b0
kernel: [  154.522763]        vfs_write+0xad/0x1a0
kernel: [  154.522765]        ksys_write+0xa4/0xe0
kernel: [  154.522767]        do_syscall_64+0x64/0x2b0
kernel: [  154.522769]        entry_SYSCALL_64_after_hwframe+0x49/0xbe
kernel: [  154.522770]
kernel: [  154.522770] -> #2 (kn->count#253){++++}:
kernel: [  154.522775]        __kernfs_remove+0x253/0x2c0
kernel: [  154.522778]        kernfs_remove+0x1f/0x30
kernel: [  154.522780]        kobject_del+0x28/0x60
kernel: [  154.522783]        mddev_delayed_delete+0x24/0x30 [md_mod]
kernel: [  154.522786]        process_one_work+0x2a7/0x5f0
kernel: [  154.522788]        worker_thread+0x2d/0x3d0
kernel: [  154.522793]        kthread+0x117/0x130
kernel: [  154.522795]        ret_from_fork+0x3a/0x50
kernel: [  154.522796]
kernel: [  154.522796] -> #1 ((work_completion)(&mddev->del_work)){+.+.}:
kernel: [  154.522800]        process_one_work+0x27e/0x5f0
kernel: [  154.522802]        worker_thread+0x2d/0x3d0
kernel: [  154.522804]        kthread+0x117/0x130
kernel: [  154.522806]        ret_from_fork+0x3a/0x50
kernel: [  154.522807]
kernel: [  154.522807] -> #0 ((wq_completion)md_misc){+.+.}:
kernel: [  154.522813]        __lock_acquire+0x1392/0x1690
kernel: [  154.522816]        lock_acquire+0xb4/0x1a0
kernel: [  154.522818]        flush_workqueue+0xab/0x4b0
kernel: [  154.522821]        md_open+0xb6/0xc0 [md_mod]
kernel: [  154.522823]        __blkdev_get+0xea/0x590
kernel: [  154.522825]        blkdev_get+0x65/0x140
kernel: [  154.522828]        do_dentry_open+0x1d1/0x380
kernel: [  154.522831]        path_openat+0x567/0xcc0
kernel: [  154.522834]        do_filp_open+0x9b/0x110
kernel: [  154.522836]        do_sys_openat2+0x201/0x2a0
kernel: [  154.522838]        do_sys_open+0x57/0x80
kernel: [  154.522840]        do_syscall_64+0x64/0x2b0
kernel: [  154.522842]        entry_SYSCALL_64_after_hwframe+0x49/0xbe
kernel: [  154.522844]
kernel: [  154.522844] other info that might help us debug this:
kernel: [  154.522844]
kernel: [  154.522846] Chain exists of:
kernel: [  154.522846]   (wq_completion)md_misc --> &mddev->reconfig_mutex --> &bdev->bd_mutex
kernel: [  154.522846]
kernel: [  154.522850]  Possible unsafe locking scenario:
kernel: [  154.522850]
kernel: [  154.522852]        CPU0                    CPU1
kernel: [  154.522853]        ----                    ----
kernel: [  154.522854]   lock(&bdev->bd_mutex);
kernel: [  154.522856]                                lock(&mddev->reconfig_mutex);
kernel: [  154.522858]                                lock(&bdev->bd_mutex);
kernel: [  154.522860]   lock((wq_completion)md_misc);
kernel: [  154.522861]
kernel: [  154.522861]  *** DEADLOCK ***
kernel: [  154.522861]
kernel: [  154.522864] 1 lock held by mdadm/2482:
kernel: [  154.522865]  #0: ffff88804efa9338 (&bdev->bd_mutex){+.+.}, at: __blkdev_get+0x79/0x590
kernel: [  154.522868]
kernel: [  154.522868] stack backtrace:
kernel: [  154.522873] CPU: 1 PID: 2482 Comm: mdadm Tainted: G           O      5.6.0-rc7-lp151.27-default #25
kernel: [  154.522875] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
kernel: [  154.522878] Call Trace:
kernel: [  154.522881]  dump_stack+0x8f/0xcb
kernel: [  154.522884]  check_noncircular+0x194/0x1b0
kernel: [  154.522888]  ? __lock_acquire+0x1392/0x1690
kernel: [  154.522890]  __lock_acquire+0x1392/0x1690
kernel: [  154.522893]  lock_acquire+0xb4/0x1a0
kernel: [  154.522895]  ? flush_workqueue+0x84/0x4b0
kernel: [  154.522898]  flush_workqueue+0xab/0x4b0
kernel: [  154.522900]  ? flush_workqueue+0x84/0x4b0
kernel: [  154.522905]  ? md_open+0xb6/0xc0 [md_mod]
kernel: [  154.522908]  md_open+0xb6/0xc0 [md_mod]
kernel: [  154.522910]  __blkdev_get+0xea/0x590
kernel: [  154.522912]  ? bd_acquire+0xc0/0xc0
kernel: [  154.522914]  blkdev_get+0x65/0x140
kernel: [  154.522916]  ? bd_acquire+0xc0/0xc0
kernel: [  154.522918]  do_dentry_open+0x1d1/0x380
kernel: [  154.522921]  path_openat+0x567/0xcc0
kernel: [  154.522923]  ? __lock_acquire+0x380/0x1690
kernel: [  154.522926]  do_filp_open+0x9b/0x110
kernel: [  154.522929]  ? __alloc_fd+0xe5/0x1f0
kernel: [  154.522935]  ? kmem_cache_alloc+0x28c/0x630
kernel: [  154.522939]  ? do_sys_openat2+0x201/0x2a0
kernel: [  154.522941]  do_sys_openat2+0x201/0x2a0
kernel: [  154.522944]  do_sys_open+0x57/0x80
kernel: [  154.522946]  do_syscall_64+0x64/0x2b0
kernel: [  154.522948]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
kernel: [  154.522951] RIP: 0033:0x7f98d279d9ae

And md_alloc also flushed the same workqueue, but the thing is different
here. Because all the paths call md_alloc don't hold bdev->bd_mutex, and
the flush is necessary to avoid race condition, so leave it as it is.

Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

md: add new workqueue for delete rdev

Since the purpose of call flush_workqueue in new_dev_store is to ensure
md_delayed_delete() has completed, so we should check rdev->del_work is
pending or not.

To suppress lockdep warning, we have to check mddev->del_work while
md_delayed_delete is attached to rdev->del_work, so it is not aligned
to the purpose of flush workquee. So a new workqueue is needed to avoid
the awkward situation, and introduce a new func flush_rdev_wq to flush
the new workqueue after check if there was pending work.

Also like new_dev_store, ADD_NEW_DISK ioctl has the same purpose to flush
workqueue while it holds bdev->bd_mutex, so make the same change applies
to the ioctl to avoid similar lock issue.

And md_delayed_delete actually wants to delete rdev, so rename the function
to rdev_delayed_delete.

Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

md: add checkings before flush md_misc_wq

Coly reported possible circular locking dependencyi with LOCKDEP enabled,
quote the below info from the detailed report [1].

[ 1607.673903] Chain exists of:
[ 1607.673903]   kn->count#256 --> (wq_completion)md_misc -->
(work_completion)(&rdev->del_work)
[ 1607.673903]
[ 1607.827946]  Possible unsafe locking scenario:
[ 1607.827946]
[ 1607.898780]        CPU0                    CPU1
[ 1607.952980]        ----                    ----
[ 1608.007173]   lock((work_completion)(&rdev->del_work));
[ 1608.069690]                                lock((wq_completion)md_misc);
[ 1608.149887]                                lock((work_completion)(&rdev->del_work));
[ 1608.242563]   lock(kn->count#256);
[ 1608.283238]
[ 1608.283238]  *** DEADLOCK ***
[ 1608.283238]
[ 1608.354078] 2 locks held by kworker/5:0/843:
[ 1608.405152]  #0: ffff8889eecc9948 ((wq_completion)md_misc){+.+.}, at:
process_one_work+0x42b/0xb30
[ 1608.512399]  #1: ffff888a1d3b7e10
((work_completion)(&rdev->del_work)){+.+.}, at: process_one_work+0x42b/0xb30
[ 1608.632130]

Since works (rdev->del_work and mddev->del_work) are queued in md_misc_wq,
then lockdep_map lock is held if either of them are running, then both of
them try to hold kernfs lock by call kobject_del. Then if new_dev_store
or array_state_store are triggered by write to the related sysfs node, so
the write operation gets kernfs lock, but need the lockdep_map because all
of them would trigger flush_workqueue(md_misc_wq) finally, then the same
lockdep_map lock is needed.

To suppress the lockdep warnning, we should flush the workqueue in case the
related work is pending. And several works are attached to md_misc_wq, so
we need to check which work should be checked:

1. for __md_stop_writes, the purpose of call flush workqueue is ensure sync
thread is started if it was starting, so check mddev->del_work is pending
or not since md_start_sync is attached to mddev->del_work.

2. __md_stop flushes md_misc_wq to ensure event_work is done, check the
event_work is enough. Assume raid_{ctr,dtr} -> md_stop -> __md_stop doesn't
need the kernfs lock.

3. both new_dev_store (holds kernfs lock) and ADD_NEW_DISK ioctl (holds the
bdev->bd_mutex) call flush_workqueue to ensure md_delayed_delete has
completed, this case will be handled in next patch.

4. md_open flushes workqueue to ensure the previous md is disappeared, but
it holds bdev->bd_mutex then try to flush workqueue, so it is better to
check mddev->del_work as well to avoid potential lock issue, this will be
done in another patch.

[1]: https://marc.info/?l=linux-raid&m=158518958031584&w=2

Cc: Coly Li <colyli@suse.de>
Reported-by: Coly Li <colyli@suse.de>
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

Merge tag 'floppy-for-5.8' of https://github.com/evdenis/linux-floppy into for-5.8/drivers

Floppy patches for 5.8

Cleanups:
  - symbolic register names for x86,sparc64,sparc32,powerpc,parisc,m68k
  - split of local/global variables for drive,fdc
  - UBSAN warning suppress in setup_rw_floppy()

Changes were compile tested on arm, sparc64, powerpc, m68k. Many patches
introduce no binary changes by using defines instead of magic numbers.
The patches were also tested with syzkaller and simple write/read/format
tests on real hardware.

Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* tag 'floppy-for-5.8' of https://github.com/evdenis/linux-floppy: (31 commits)
  floppy: suppress UBSAN warning in setup_rw_floppy()
  floppy: add defines for sizes of cmd & reply buffers of floppy_raw_cmd
  floppy: add FD_AUTODETECT_SIZE define for struct floppy_drive_params
  floppy: use print_hex_dump() in setup_DMA()
  floppy: cleanup: make set_fdc() always set current_drive and current_fd
  floppy: cleanup: get rid of current_reqD in favor of current_drive
  floppy: make sure to reset all FDCs upon resume()
  floppy: cleanup: do not iterate on current_fdc in do_floppy_init()
  floppy: cleanup: add a few comments about expectations in certain functions
  floppy: cleanup: do not iterate on current_fdc in DMA grab/release functions
  floppy: cleanup: make get_fdc_version() not rely on current_fdc anymore
  floppy: cleanup: make next_valid_format() not rely on current_drive anymore
  floppy: cleanup: make check_wp() not rely on current_{fdc,drive} anymore
  floppy: cleanup: make fdc_specify() not rely on current_{fdc,drive} anymore
  floppy: cleanup: make fdc_configure() not rely on current_fdc anymore
  floppy: cleanup: make perpendicular_mode() not rely on current_fdc anymore
  floppy: cleanup: make need_more_output() not rely on current_fdc anymore
  floppy: cleanup: make result() not rely on current_fdc anymore
  floppy: cleanup: make output_byte() not rely on current_fdc anymore
  floppy: cleanup: make wait_til_ready() not rely on current_fdc anymore
  ...

floppy: suppress UBSAN warning in setup_rw_floppy()

UBSAN: array-index-out-of-bounds in drivers/block/floppy.c:1521:45
index 16 is out of range for type 'unsigned char [16]'
Call Trace:
...
 setup_rw_floppy+0x5c3/0x7f0
 floppy_ready+0x2be/0x13b0
 process_one_work+0x2c1/0x5d0
 worker_thread+0x56/0x5e0
 kthread+0x122/0x170
 ret_from_fork+0x35/0x40

From include/uapi/linux/fd.h:
struct floppy_raw_cmd {
...
unsigned char cmd_count;
unsigned char cmd[16];
unsigned char reply_count;
unsigned char reply[16];
...
}

This out-of-bounds access is intentional. The command in struct
floppy_raw_cmd may take up the space initially intended for the reply
and the reply count. It is needed for long 82078 commands such as
RESTORE, which takes 17 command bytes. Initial cmd size is not enough
and since struct setup_rw_floppy is a part of uapi we check that
cmd_count is in [0:16+1+16] in raw_cmd_copyin().

The patch adds union with original cmd,reply_count,reply fields and
fullcmd field of equivalent size. The cmd accesses are turned to
fullcmd where appropriate to suppress UBSAN warning.

Link: https://lore.kernel.org/r/20200501134416.72248-5-efremov@linux.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: add defines for sizes of cmd & reply buffers of floppy_raw_cmd

Use FD_RAW_CMD_SIZE, FD_RAW_REPLY_SIZE defines instead of magic numbers
for cmd & reply buffers of struct floppy_raw_cmd. Remove local to
floppy.c MAX_REPLIES define, as it is now FD_RAW_REPLY_SIZE.
FD_RAW_CMD_FULLSIZE added as we allow command to also fill reply_count
and reply fields.

Link: https://lore.kernel.org/r/20200501134416.72248-4-efremov@linux.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: add FD_AUTODETECT_SIZE define for struct floppy_drive_params

Use FD_AUTODETECT_SIZE for autodetect buffer size in struct
floppy_drive_params instead of a magic number.

Link: https://lore.kernel.org/r/20200501134416.72248-3-efremov@linux.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: use print_hex_dump() in setup_DMA()

Remove pr_cont() and use print_hex_dump() in setup_DMA() to print the
contents of the cmd buffer.

Link: https://lore.kernel.org/r/20200501134416.72248-2-efremov@linux.com
Suggested-by: Joe Perches <joe@perches.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: make set_fdc() always set current_drive and current_fd

When called with a negative drive value, set_fdc() would stick to the
current fdc (which was assumed to reflect the current_drive's FDC). We
do not need this anymore as the last call place with a negative value
was just addressed. Let's make this function always set both current_fdc
and current_drive so that there's no more ambiguity. A few comments
stating this were added to a few non-obvious places.

Link: https://lore.kernel.org/r/20200410101904.14652-3-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: get rid of current_reqD in favor of current_drive

This macro equals -1 and is used as an alternative for current_drive when
calling reschedule_timeout(), which in turn needs to remap it. This only
adds obfuscation, let's simply use current_drive.

Link: https://lore.kernel.org/r/20200410101904.14652-2-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: make sure to reset all FDCs upon resume()

In floppy_resume() we don't properly reinitialize all FDCs, instead
we reinitialize the current FDC once per available FDC because value
-1 is passed to user_reset_fdc(). Let's simply save the current drive
and properly reinitialize each FDC.

Link: https://lore.kernel.org/r/20200410101904.14652-1-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: do not iterate on current_fdc in do_floppy_init()

There's no need to iterate on current_fdc in do_floppy_init() anymore,
in the first case it's only used as an array index to access fdc_state[],
so let's get rid of this confusing assignment. The second case is a bit
trickier because user_reset_fdc() needs to already know current_fdc when
called with drive==-1 due to this call chain:

    user_reset_fdc()
      lock_fdc()
        set_fdc()
           drive<0 ==> new_fdc = current_fdc

Note that current_drive is not used in this code part and may even not
match a unit belonging to current_fdc. Instead of passing -1 we can
simply pass the first drive of the FDC being initialized, which is even
cleaner as it will allow the function chain above to consistently assign
both variables.

Link: https://lore.kernel.org/r/20200410093023.14499-1-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: add a few comments about expectations in certain functions

The locking in the driver is far from being obvious, with unlocking
automatically happening at end of operations scheduled by interrupt,
especially for the error paths where one does not necessarily expect
that such an interrupt may be triggered. Let's add a few comments
about what to expect at certain places to avoid misdetecting bugs
which are not.

Link: https://lore.kernel.org/r/20200331094054.24441-24-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: do not iterate on current_fdc in DMA grab/release functions

Both floppy_grab_irq_and_dma() and floppy_release_irq_and_dma() used to
iterate on the global variable while setting up or freeing resources.
Now that they exclusively rely on functions which take the fdc as an
argument, so let's not touch the global one anymore.

Link: https://lore.kernel.org/r/20200331094054.24441-23-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: make get_fdc_version() not rely on current_fdc anymore

Now the fdc is passed in argument so that the function does not
use current_fdc anymore.

Link: https://lore.kernel.org/r/20200331094054.24441-22-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: make next_valid_format() not rely on current_drive anymore

Now the drive is passed in argument so that the function does not
use current_drive anymore.

Link: https://lore.kernel.org/r/20200331094054.24441-21-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: make check_wp() not rely on current_{fdc,drive} anymore

Now the fdc and drive are passed in argument so that the function does
not use current_fdc nor current_drive anymore.

Link: https://lore.kernel.org/r/20200331094054.24441-20-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: make fdc_specify() not rely on current_{fdc,drive} anymore

Now the fdc and drive are passed in argument so that the function does
not use current_fdc nor current_drive anymore.

Link: https://lore.kernel.org/r/20200331094054.24441-19-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: make fdc_configure() not rely on current_fdc anymore

Now the fdc is passed in argument so that the function does not
use current_fdc anymore.

Link: https://lore.kernel.org/r/20200331094054.24441-18-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: make perpendicular_mode() not rely on current_fdc anymore

Now the fdc is passed in argument so that the function does not
use current_fdc anymore.

It's worth noting that there's still a single raw_cmd pointer
specific to the current fdc. It may make sense to have one per
fdc in the future. In addition, cont->done() still relies on the
current drive and current raw_cmd.

Link: https://lore.kernel.org/r/20200331094054.24441-17-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: make need_more_output() not rely on current_fdc anymore

Now the fdc is passed in argument so that the function does not
use current_fdc anymore.

Link: https://lore.kernel.org/r/20200331094054.24441-16-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: make result() not rely on current_fdc anymore

Now the fdc is passed in argument so that the function does not
use current_fdc anymore.

It's worth noting that there's still a single reply_buffer[] which
will store the result for the current fdc. It may or may not make
sense to implement one buffer per fdc in the future.

Link: https://lore.kernel.org/r/20200331094054.24441-15-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: make output_byte() not rely on current_fdc anymore

Now the fdc is passed in argument so that the function does not
use current_fdc anymore.

Link: https://lore.kernel.org/r/20200331094054.24441-14-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: make wait_til_ready() not rely on current_fdc anymore

Now the fdc is passed in argument so that the function does not
use current_fdc anymore.

Link: https://lore.kernel.org/r/20200331094054.24441-13-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: make show_floppy() not rely on current_fdc anymore

Now the fdc is passed in argument so that the function does not
use current_fdc anymore.

Link: https://lore.kernel.org/r/20200331094054.24441-12-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: make reset_fdc_info() not rely on current_fdc anymore

Now the fdc is passed in argument so that the function does not
use current_fdc anymore.

Link: https://lore.kernel.org/r/20200331094054.24441-11-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: cleanup: make twaddle() not rely on current_{fdc,drive} anymore

Now the fdc and drive are passed in argument so that the function does
not use current_fdc nor current_drive anymore.

Link: https://lore.kernel.org/r/20200331094054.24441-10-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: use symbolic register names in the x86 port

Now we can use FD_STATUS and FD_DATA instead of 4 or 5, let's do
this, and also use STATUS_DMA and STATUS_READY for the status bits.

Link: https://lore.kernel.org/r/20200331094054.24441-9-w@1wt.eu
Cc: x86@kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: use symbolic register names in the sparc64 port

Now by splitting the base address from the register index we can
use the symbolic register names instead of the hard-coded numeric
values.

Link: https://lore.kernel.org/r/20200331094054.24441-8-w@1wt.eu
Cc: "David S. Miller" <davem@davemloft.net>
[willy: fix printk warnings s/%lx/%x/g in sun_82077_fd_{inb,outb}()]
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: use symbolic register names in the sparc32 port

The sparc port used to be forced to rely on numeric register indexes
with their equivalent in comments. Now that they don't depend on the
IO port we can use their symbolic names.

Link: https://lore.kernel.org/r/20200331094054.24441-7-w@1wt.eu
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: use symbolic register names in the powerpc port

Now we can use FD_STATUS and FD_DATA instead of 4 or 5, let's do
this, and also use STATUS_DMA and STATUS_READY for the status bits.

Link: https://lore.kernel.org/r/20200331094054.24441-6-w@1wt.eu
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: use symbolic register names in the parisc port

Now we can use FD_STATUS and FD_DATA instead of 4 or 5, let's do
this, and also use STATUS_DMA and STATUS_READY for the status bits.

Link: https://lore.kernel.org/r/20200331094054.24441-5-w@1wt.eu
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: use symbolic register names in the m68k port

Now we can use FD_STATUS and FD_DATA instead of 4 or 5, let's do
this, and also use STATUS_DMA and STATUS_READY for the status bits.

Link: https://lore.kernel.org/r/20200331094054.24441-4-w@1wt.eu
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: add references to 82077's extra registers

This controller provides extra status registers SRA and SRB as well
as a tape drive register (TDR) and a data rate select register (DSR),
which are referenced in the sparc port, so let's have their symbolic
definitions centralized.

Link: https://lore.kernel.org/r/20200331094054.24441-3-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

floppy: split the base port from the register in I/O accesses

Currently we have architecture-specific fd_inb() and fd_outb() functions
or macros, taking just a port which is in fact made of a base address and
a register. The base address is FDC-specific and derived from the local or
global "fdc" variable through the FD_IOPORT macro used in the base address
calculation.

This change splits this by explicitly passing the FDC's base address and
the register separately to fd_outb() and fd_inb(). It affects the
following archs:
  - x86, alpha, mips, powerpc, parisc, arm, m68k:
    simple remap of port -> base+reg

  - sparc32: use of reg only, since the base address was already masked
    out and the FDC controller is known from a static struct.

  - sparc64: like x86 for PCI, like sparc32 for 82077

Some archs use inline functions and others macros. This was not
unified in order to minimize the number of changes to review. For the
same reason checkpatch still spews a few warnings about things that
were already there before.

The parisc still uses hard-coded register values and could be cleaned up
by taking the register definitions.

The sparc per-controller inb/outb functions could further be refined
to explicitly take an FDC register instead of a port in argument but it
was not needed yet and may be cleaned later.

Link: https://lore.kernel.org/r/20200331094054.24441-2-w@1wt.eu
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Ian Molton <spyro@f2s.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: x86@kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>

nvme: define constants for identification values

Improve code readability by defining the specification's constants that
the driver is using when decoding identification payloads.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Bart van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvmet: align addrfam list to spec

With reference to the NVMeOF Specification (page 44, Figure 38)
discovery log page entry provides address family field. We do set the
transport type field but the adrfam field is not set when using loop
transport and also it doesn't have support in the nvme-cli. So when
reading discovery log page with a loop transport it leads to confusing
output.

As per the spec for adrfam value 254 is reserved for Intra Host
Transport i.e. loopback), we add a required macro in the protocol
header file, set default port disc addr entry's adrfam to
NVMF_ADDR_FAMILY_MAX, and update nvmet_addr_family configfs array for
show/store attribute.

Without this patch, setting adrfam to (ipv4/ipv6/ib/fc/loop/" ") we get
following output for nvme discover command from nvme-cli which is
confusing.
trtype:  loop
adrfam:  ipv4
trtype:  loop
adrfam:  ipv6
trtype:  loop
adrfam:  infiniband
trtype:  loop
adrfam:  fibre-channel
trtype:  loop # ${CFGFS_HOME}/nvmet/ports/1/addr_adrfam = loop
adrfam:  pci            # <----- pci for loop
trtype:  loop # ${CFGFS_HOME}/nvmet/ports/1/addr_adrfam = " "
adrfam:  pci            # <----- pci for unrecognized

This patch fixes above output :-
trtype:  loop
adrfam:  ipv4
trtype:  loop
adrfam:  ipv6
trtype:  loop
adrfam:  infiniband
trtype:  loop
adrfam:  fibre-channel
trtype:  loop           # ${CFGFS_HOME}/nvmet/ports/1/addr_adrfam = loop
adrfam:  loop           # <----- loop for loop
trtype:  loop # ${CFGFS_HOME}/config/nvmet/ports/adrfam = " "
adrfam:  unrecognized   # <----- unrecognized when invalid value

Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvmet: centralize port enable access for configfs

The configfs attributes which are supposed to set when port is disable
such as addr[addrfam|portid|traddr|treq|trsvcid|inline_data_size|trtype]
has repetitive check and generic error message printing.

This patch creates centralize helper to check and print an error
message that also accepts caller as a parameter. This makes error
message easy to parse for the user, removes the duplicate code and
makes it available for futures such scenarios.

Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvmet: use type-name map for address treq

Currently nvmet_addr_treq_[store|show]() uses switch and if else
ladder for address transport requirements to string and reverse
mapping. With addtion of the generic nvmet_type_name_map structure
we can get rid of the switch and if else ladder with string
duplication.

Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvmet: use type-name map for ana states

Now that we have a generic type to name map for configfs, get rid of
the nvmet_ana_state_names structure and replace it with newly added
nvmet_type_name_map.

Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvmet: use type-name map for address family

Right now nvmet_addr_adrfam_[store|show]() uses switch and if else
ladder for address family to string and reverse mapping which also
repeats the strings in show and store function.

With addition of generic nvmet_type_name_map structure we can now get rid
of the switch and if else ladder and string duplication.

Also, we add a newline in before found label in nvmet_addr_trtype_store()
which keeps goto label code consistent with
nvmet_allowed_hosts_drop_link(), nvmet_port_subsys_drop_link() and
nvmet_ana_group_ana_state_store().

Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvmet: add generic type-name mapping

This patch adds a new type to name mapping generic structure. It
replaces nvmet_transport_name with new generic mapping structure
nvmet_transport.

Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme-multipath: stop using ->queuedata

nvme-multipath already uses the gendisk private data, not need to
also set up the request_queue queuedata and use it in one place only.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme-tcp: try to send request in queue_rq context

Today, nvme-tcp automatically schedules a send request
to a workqueue context, which is 1 more than we'd need
in case the socket buffer is wide open.

However, because we have async send activity (as a result
of r2t, or write_space callbacks), we need to synchronize
sends from possibly multiple contexts (ideally all running
on the same cpu though).

Thus, we only try to send directly from queue_rq in cases:
1. the send_list is empty
2. we can send it synchronously (i.e. not from the RX path)
3. we run on the same cpu as the queue->io_cpu to avoid
   contention on the send operation.

Proposed-by: Mark Wunderlich <mark.wunderlich@intel.com>
Signed-off-by: Mark Wunderlich <mark.wunderlich@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme-tcp: avoid scheduling io_work if we are already polling

When the user runs polled I/O, we shouldn't have to trigger
the workqueue to generate the receive work upon the .data_ready
upcall. This prevents a redundant context switch when the
application is already polling for completions.

Proposed-by: Mark Wunderlich <mark.wunderlich@intel.com>
Signed-off-by: Mark Wunderlich <mark.wunderlich@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme-tcp: use bh_lock in data_ready

data_ready may be invoked from send context or from
softirq, so need bh locking for that.

Fixes: 3f2304f8c6d6 ("nvme-tcp: add NVMe over TCP host driver")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme-pci: align io queue count with allocted nvme_queue in nvme_probe

Since commit 147b27e4bd08 ("nvme-pci: allocate device queues storage
space at probe"), nvme_alloc_queue does not alloc the nvme queues
itself anymore.

If the write/poll_queues module parameters are changed at runtime to
values larger than the number of allocated queues in nvme_probe,
nvme_alloc_queue will access unallocated memory.

Add a new nr_allocated_queues member to struct nvme_dev to record how
many queues were alloctated in nvme_probe to avoid using more than the
allocated queues after a reset following a change to the
write/poll_queues module parameters.

Also add nr_write_queues and nr_poll_queues members to allow refreshing
the number of write and poll queues based on a change to the module
parameters when resetting the controller.

Fixes: 147b27e4bd08 ("nvme-pci: allocate device queues storage space at probe")
Signed-off-by: Weiping Zhang <zhangweiping@didiglobal.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
[hch: add nvme_max_io_queues, update the commit message]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme-pci: remove last_sq_tail

The nvme driver does not have enough tags to wrap the queue, and blk-mq
will no longer call commit_rqs() when there are no new submissions to
notify.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme-pci: remove volatile cqes

The completion queue entry is not volatile once the phase is confirmed.
Remove the volatile keywords and check the phase using the appropriate
READ_ONCE() accessor, allowing the compiler to optimize the remaining
completion path.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: flush scan work on passthrough commands

If a passthrough command causes the namespace inventory or capabilities
to change, flush the scan work that handles these changes so the driver
synchronizes with the user command's effects before returning the result
to user space.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: clean up error handling in nvme_init_ns_head

Use a common label for putting the nshead if needed and only convert
nvme status codes for the one case where it actually is needed.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme-fc: avoid gcc-10 zero-length-bounds warning

When CONFIG_ARCH_NO_SG_CHAIN is set, op->sgl[0] cannot be dereferenced,
as gcc-10 now points out:

drivers/nvme/host/fc.c: In function 'nvme_fc_init_request':
drivers/nvme/host/fc.c:1774:29: warning: array subscript 0 is outside the bounds of an interior zero-length array 'struct scatterlist[0]' [-Wzero-length-bounds]
 1774 |  op->op.fcp_req.first_sgl = &op->sgl[0];
      |                             ^~~~~~~~~~~
drivers/nvme/host/fc.c:98:21: note: while referencing 'sgl'
   98 |  struct scatterlist sgl[NVME_INLINE_SG_CNT];
      |                     ^~~

I don't know if this is a legitimate warning or a false-positive.
If this is just a false alarm, the warning is easily suppressed
by interpreting the array as a pointer.

Fixes: b1ae1a238900 ("nvme-fc: Avoid preallocating big SGL for data")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvmet: add ns revalidation support

Add support for detecting capacity changes on nvmet blockdev and file
backed namespaces. This allows for emulating and testing online resizing
of nvme devices and filesystems on top.

Signed-off-by: Anthony Iliopoulos <ailiop@suse.com>
[chaitanya: Fix comments posted on V1]
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
[hch: reuse code a bit more]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: consolodate io settings

The stream parameters indicating optimal io settings were just getting
overwritten later. Rearrange the settings so the streams parameters can
be preserved if provided.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: revalidate namespace stream parameters

The stream parameters are based on the currently formatted logical block
size. Recheck these parameters on namespace revalidation so the
registered constraints will be accurate.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: consolidate chunk_sectors settings

Move the quirked chunk_sectors setting to the same location as noiob so
one place registers this setting. And since the noiob value is only used
locally, remove the member from struct nvme_ns.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: revalidate after verifying identifiers

If the namespace identifiers have changed, skip updating the disk
information, as that will register parameters from a mismatched
namespace.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme-multipath: set bdi capabilities once

The queues' backing device info capabilities don't change with each
namespace revalidation. Set it only when each path's request_queue
is initially added to a multipath queue.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: check namespace head shared property

Reject a new shared namespace if a duplicate unshared namespace exists.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: always search for namespace head

Even if a namespace reports it is not capable of sharing, search the
subsystem for a matching namespace head. If found, the driver should
reject that namespace since it's coming from an invalid configuration.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: release namespace head reference on error

If a namespace identification does not match the subsystem's head for
that NSID, release the reference that was taken when the matching head
was initially found.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: unlink head after removing last namespace

The driver had been unlinking the namespace head from the subsystem's
list only after the last reference was released, and outside of the
list's subsys->lock protection.

There is no reason to track an empty head, so unlink the entry from the
subsystem's list when the last namespace using that head is removed and
with the mutex lock protecting the list update. The next namespace to
attach reusing the previous NSID will allocate a new head rather than
find the old head with mismatched identifiers.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: remove the magic 1024 constant in nvme_scan_ns_list

Replace it with a value derived from the identify data and nsid sizes.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: avoid an Identify Controller command for each namespace scan

The namespace lists are 0-terminated, so we don't really need the NN value
execept for the legacy sequential scan.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: factor out a nvme_ns_remove_by_nsid helper

Factor out a piece of deeply indented and logicaly separate code
from nvme_scan_ns_list into a new helper.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: clean up nvme_scan_work

Move the check for the supported CNS value into nvme_scan_ns_list, and
limit the life time of the identify controller allocation.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: refine the Qemu Identify CNS quirk

Add a helper to check if we can use Identify CNS values > 1, and refine
the Qemu quirk to not apply to reported versions larger than 1.1, as the
Qemu implementation had been fixed by then.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvmet-fc: slight cleanup for kbuild test warnings

The kbuild tst robot flagged the following 3 issues:

Case 1)
>> drivers/nvme/target/fc.c:1201:37: warning: Either the condition
>> '!assoc' is redundant or there is possible null pointer dereference:
>> assoc. [nullPointerRedundantCheck]
>>  struct nvmet_fc_tgtport *tgtport = assoc->tgtport;
                                       ^
>> drivers/nvme/target/fc.c:1853:7: note: Assuming that condition '!assoc'
>> is not redundant
>>   if (!assoc)
         ^
>> drivers/nvme/target/fc.c:1850:37: note: Assignment
>> 'assoc=nvmet_fc_find_target_assoc(tgtport,be64_to_cpu(
>>              rqst->associd.association_id))', assigned value is 0
>>   assoc = nvmet_fc_find_target_assoc(tgtport,
                                       ^
>> drivers/nvme/target/fc.c:1896:31: note: Calling function
>> 'nvmet_fc_delete_target_assoc', 1st argument 'assoc' value is 0
>>  nvmet_fc_delete_target_assoc(assoc);
                                 ^

The tool isn't smart enough to see that line 1854 sets a ret value which
thereafter causes the routine to exit. This occurs before any of the assoc
references, so it is not an issue. There are 2 more reportings of this
same failure.

To quiet the tool - rework the if test that does the exit to also
reference assoc.  No change in logic otherwise.

Case 2)
drivers/nvme/target/fc.c:1202:29: warning: The scope of the variable
'queue' can be reduced. [variableScope]
    struct nvmet_fc_tgt_queue *queue;
                               ^

The tool is requesting the variable be declared within the code block
that utilizes it. Ignoring this report as existing code style is fine.

Case 3)
drivers/nvme/target/fc.c:1137:16: warning: Variable 'needrandom' is
assigned a value that is never used. [unreadVariable]
       needrandom = true;
                  ^

Another parsing issue with the tool. Given that parens were not used
with the list_for_each_entry() check, it inadvertantly thinks the
break exited the outer while loop not the inner for loop.

This is not an error. But, added parens to the inner list_for_each_entry()
to quiet the tool and as it is better coding style.

-- james

Signed-off-by: James Smart <jsmart2021@gmail.com>
Reported-by: kbuild test robot <lkp@intel.com>
CC: kbuild test robot <lkp@intel.com>
CC: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvmet-rdma: use SRQ per completion vector

In order to save resource allocation and utilize the completion
locality in a better way (compared to SRQ per device that exist today),
allocate Shared Receive Queues (SRQs) per completion vector. Associate
each created QP/CQ with an appropriate SRQ according to the queue index.
This association will reduce the lock contention in the fast path
(compared to SRQ per device solution) and increase the locality in
memory buffers. Add new module parameter for SRQ size to adjust it
according to the expected load. User should make sure the size is >= 256
to avoid lack of resources. Also reduce the debug level of "last WQE
reached" event that is raised when a QP is using SRQ during destruction
process to relief the log.

Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: remove unused parameter

nvme_alloc_ns_head() doesn't use the 'struct nvme_id_ns' parameter.
Remove it, and update caller accordingly.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: provide num dword helper

Various nvme commands use a zeroes based number of dwords field. Create
a helper function to convert byte lengths to this format.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

lpfc: nvmet: Add Send LS Request and Abort LS Request support

Now that common helpers exist, add the ability to Send an NVME LS Request
and to Abort an outstanding LS Request to the nvmet side of the driver.

Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

lpfc: nvmet: Add support for NVME LS request hosthandle

As the nvmet layer does not have the concept of a remoteport object, which
can be used to identify the entity on the other end of the fabric that is
to receive an LS, the hosthandle was introduced.  The driver passes the
hosthandle, a value representative of the remote port, with a ls request
receive. The LS request will create the association.  The transport will
remember the hosthandle for the association, and if there is a need to
initiate a LS request to the remote port for the association, the
hosthandle will be used. When the driver loses connectivity with the
remote port, it needs to notify the transport that the hosthandle is no
longer valid, allowing the transport to terminate associations related to
the hosthandle.

This patch adds support to the driver for the hosthandle. The driver will
use the ndlp pointer of the remote port for the hosthandle in calls to
nvmet_fc_rcv_ls_req().  The discovery engine is updated to invalidate the
hosthandle whenever connectivity with the remote port is lost.

Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

lpfc: nvme: Add Receive LS Request and Send LS Response support to nvme

Now that common helpers exist, add the ability to receive NVME LS requests
to the driver. New requests will be delivered to the transport by
nvme_fc_rcv_ls_req().

In order to complete the LS, add support for Send LS Response and send
LS response completion handling to the driver.

Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

lpfc: Refactor Send LS Response support

Currently, the ability to send an NVME LS response is limited to the nvmet
(controller/target) side of the driver.  In preparation of both the nvme
and nvmet sides supporting Send LS Response, rework the existing send
ls_rsp and ls_rsp completion routines such that there is common code that
can be used by both sides.

Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

lpfc: Refactor Send LS Abort support

Send LS Abort support is needed when Send LS Request is supported.

Currently, the ability to abort an NVME LS request is limited to the nvme
(host) side of the driver.  In preparation of both the nvme and nvmet sides
supporting Send LS Abort, rework the existing ls_req abort routines such
that there is common code that can be used by both sides.

While refactoring it was seen the logic in the abort routine was incorrect.
It attempted to abort all NVME LS's on the indicated port. As such, the
routine was reworked to abort only the NVME LS request that was specified.

Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

lpfc: Refactor Send LS Request support

Currently, the ability to send an NVME LS request is limited to the nvme
(host) side of the driver.  In preparation of both the nvme and nvmet sides
support Send LS Request, rework the existing send ls_req and ls_req
completion routines such that there is common code that can be used by
both sides.

Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

lpfc: Refactor NVME LS receive handling

In preparation for supporting both intiator mode and target mode
receiving NVME LS's, commonize the existing NVME LS request receive
handling found in the base driver and in the nvmet side.

Using the original lpfc_nvmet_unsol_ls_event() and
lpfc_nvme_unsol_ls_buffer() routines as a templates, commonize the
reception of an NVME LS request. The common routine will validate the LS
request, that it was received from a logged-in node, and allocate a
lpfc_async_xchg_ctx that is used to manage the LS request. The role of
the port is then inspected to determine which handler is to receive the
LS - nvme or nvmet. As such, the nvmet handler is tied back in. A handler
is created in nvme and is stubbed out.

Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

lpfc: Commonize lpfc_async_xchg_ctx state and flag definitions

The last step of commonization is to remove the 'T' suffix from
state and flag field definitions.  This is minor, but removes the
mental association that it solely applies to nvmet use.

Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

lpfc: Refactor nvmet_rcv_ctx to create lpfc_async_xchg_ctx

To support FC-NVME-2 support (actually FC-NVME (rev 1) with Ammendment 1),
both the nvme (host) and nvmet (controller/target) sides will need to be
able to receive LS requests.  Currently, this support is in the nvmet side
only. To prepare for both sides supporting LS receive, rename
lpfc_nvmet_rcv_ctx to lpfc_async_xchg_ctx and commonize the definition.

Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

lpfc: Refactor lpfc nvme headers

A lot of files in lpfc include nvme headers, building up relationships that
require a file to change for its headers when there is no other change
necessary. It would be better to localize the nvme headers.

There is also no need for separate nvme (initiator) and nvmet (tgt)
header files.

Refactor the inclusion of nvme headers so that all nvme items are
included by lpfc_nvme.h

Merge lpfc_nvmet.h into lpfc_nvme.h so that there is a single header used
by both the nvme and nvmet sides. This prepares for structure sharing
between the two roles. Prep to add shared function prototypes for upcoming
shared routines.

Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme-fcloop: add target to host LS request support

Add support for performing LS requests from target to host.
Include sending request from targetport, reception into host,
host sending ls rsp.

Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme-fcloop: refactor to enable target to host LS

Currently nvmefc-loop only sends LS's from host to target.
Slightly rework data structures and routine names to reflect this
path. Allows a straight-forward conversion to be used by ls's
from target to host.

Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>