OSDN Git Service
Chris Wilson [Wed, 25 Sep 2013 16:34:56 +0000 (17:34 +0100)]
drm/i915: Boost RPS frequency for CPU stalls
If we encounter a situation where the CPU blocks waiting for results
from the GPU, give the GPU a kick to boost its the frequency.
This should work to reduce user interface stalls and to quickly promote
mesa to high frequencies - but the cost is that our requested frequency
stalls high (as we do not idle for long enough before rc6 to start
reducing frequencies, nor are we aggressive at down clocking an
underused GPU). However, this should be mitigated by rc6 itself powering
off the GPU when idle, and that energy use is dependent upon the workload
of the GPU in addition to its frequency (e.g. the math or sampler
functions only consume power when used). Still, this is likely to
adversely affect light workloads.
In particular, this nearly eliminates the highly noticeable wake-up lag
in animations from idle. For example, expose or workspace transitions.
(However, given the situation where we fail to downclock, our requested
frequency is almost always the maximum, except for Baytrail where we
manually downclock upon idling. This often masks the latency of
upclocking after being idle, so animations are typically smooth - at the
cost of increased power consumption.)
Stéphane raised the concern that this will punish good applications and
reward bad applications - but due to the nature of how mesa performs its
client throttling, I believe all mesa applications will be roughly
equally affected. To address this concern, and to prevent applications
like compositors from permanently boosting the RPS state, we ratelimit the
frequency of the wait-boosts each client recieves.
Unfortunately, this techinique is ineffective with Ironlake - which also
has dynamic render power states and suffers just as dramatically. For
Ironlake, the thermal/power headroom is shared with the CPU through
Intelligent Power Sharing and the intel-ips module. This leaves us with
no GPU boost frequencies available when coming out of idle, and due to
hardware limitations we cannot change the arbitration between the CPU and
GPU quickly enough to be effective.
v2: Limit each client to receiving a single boost for each active period.
Tested by QA to only marginally increase power, and to demonstrably
increase throughput in games. No latency measurements yet.
v3: Cater for front-buffer rendering with manual throttling.
v4: Tidy up.
v5: Sadly the compositor needs frequent boosts as it may never idle, but
due to its picking mechanism (using ReadPixels) may require frequent
waits. Those waits, along with the waits for the vrefresh swap, conspire
to keep the GPU at low frequencies despite the interactive latency. To
overcome this we ditch the one-boost-per-active-period and just ratelimit
the number of wait-boosts each client can receive.
Reported-and-tested-by: Paul Neumann <paul104x@yahoo.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68716
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Stéphane Marchesin <stephane.marchesin@gmail.com>
Cc: Owen Taylor <otaylor@redhat.com>
Cc: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Cc: "Zhuang, Lena" <lena.zhuang@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: No extern for function prototypes in headers.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 25 Sep 2013 16:34:55 +0000 (17:34 +0100)]
drm/i915: Fix __wait_seqno to use true infinite timeouts
When we switched to always using a timeout in conjunction with
wait_seqno, we lost the ability to detect missed interrupts. Since, we
have had issues with interrupts on a number of generations, and they are
required to be delivered in a timely fashion for a smooth UX, it is
important that we do log errors found in the wild and prevent the
display stalling for upwards of 1s every time the seqno interrupt is
missed.
Rather than continue to fix up the timeouts to work around the interface
impedence in wait_event_*(), open code the combination of
wait_event[_interruptible][_timeout], and use the exposed timer to
poll for seqno should we detect a lost interrupt.
v2: In order to satisfy the debug requirement of logging missed
interrupts with the real world requirments of making machines work even
if interrupts are hosed, we revert to polling after detecting a missed
interrupt.
v3: Throw in a debugfs interface to simulate broken hw not reporting
interrupts.
v4: s/EGAIN/EAGAIN/ (Imre)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Don't use the struct typedef in new code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 23 Sep 2013 20:33:20 +0000 (17:33 -0300)]
drm/i915: Add some missing steps to i915_driver_load error path
We missed adding a few cleanup steps for recent additions.
Reviewer: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Wed, 2 Oct 2013 16:25:02 +0000 (09:25 -0700)]
drm/i915: Clean up the ring scaling calculations
This patch attempts to clean up the ring/IA scaling programming in the
following ways.
1. Fix the comment about the DDR frequency. The math is 266MHz, not
133MHz. Formula was right, docs are wrong.
2. Mask the DCLK register since I don't know how it is defined on future
platforms.
3. use mult_frac instead of magic math.
This helps for future platform enabling.
v2: Actually use the right patch. The v1 was a mix of things, none of
which was right. Note that due to rounding, we actually get different
values (slightly higher) for the effective ring frequency.
v3: Use 1.25 instead of 1.33 as the original code did. (Jesse)
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 1 Oct 2013 19:52:14 +0000 (22:52 +0300)]
drm/i915: Don't populate pipe_src_{w,h} multiple times
If we ever end up doing the retry loop due to bandwidth constraints, we
would rewrite pipe_src_{w,n} based on adjusted_mode timings. But by that
time the encoder may have already replaced the adjusted_mode with a
fixed panel mode, which would then corrupt pipe_src_{w,h}.
v2: Use requested_mode and slap on a big comment from Daniel
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 20 Sep 2013 19:21:19 +0000 (16:21 -0300)]
drm/i915: implement the Haswell mode set sequence workaround
This workaround is described in the mode set sequence documentation.
When enabling planes for the second pipe, we need to wait for 2
vblanks on the first pipe. This should solve "a flash of screen
corruption if planes are enabled on second/third pipe during the time
that big FIFO mode is exiting". Watermarks are fun :)
v2: Save indentation levels
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 19 Sep 2013 20:00:37 +0000 (17:00 -0300)]
drm/i915: Disable/enable planes as the first/last thing during modeset on HSW
Refactor the plane enabling/disabling into helper functions and move
the calls to happen as the first thing during .crtc_disable, and the
last thing during .crtc_enable.
Those are the two clear points where we are sure that the pipe is
actually running regardless of the encoder type or hardware
generation.
v2: Made by Paulo:
Remove the code touching everything but the Haswell functions. We
need this change on Haswell right now since it fixes a FIFO underrun
that we get on pipe A while we enable pipe B (see the workaround
notes on the Haswell mode set sequence documentation). We can bring
back the code to gens 2-7 later, once they're tested.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes [Tue, 1 Oct 2013 17:41:38 +0000 (10:41 -0700)]
i915/vlv: untangle integrated clock source handling v4
The global integrated clock source bit resides in DPLL B on VLV, but we
were treating it as a per-pipe resource. It needs to be set whenever
any PLL is active, so pull setting the bit out of vlv_update_pll and
into vlv_enable_pll. Also add a vlv_disable_pll to prevent disabling it
when pipe B shuts down.
I'm guessing on the references here, I expect this to bite any config
where multiple displays are active or displays are moved from pipe to
pipe.
v2: re-add bits in vlv_update_pll to keep from confusing the state checker
v3: use enum pipe checks (Daniel)
set CRI clock source early (Ville)
consistently set CRI clock source everywhere (Ville)
v4: drop unnecessary setting of bit in vlv enable pll (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=67245
References: https://bugs.freedesktop.org/show_bug.cgi?id=69693
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: s/1/PIPE_B/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Tue, 1 Oct 2013 09:12:33 +0000 (12:12 +0300)]
drm/i915: fix typo s/PatherPoint/PantherPoint/
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Sat, 28 Sep 2013 15:46:56 +0000 (16:46 +0100)]
drm/i915: Make intel_resume_power_well() static
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 26 Sep 2013 23:05:59 +0000 (20:05 -0300)]
drm/i915: destroy connector sysfs files earlier
For some reason, every single time I try to run module_reload
something tries to read the connector sysfs files. This happens
after we destroy the encoders and before we destroy the connectors, so
when the sysfs read triggers the connector detect() function,
intel_conector->encoder points to memory that was already freed.
The bad backtrace is just:
[<
ffffffff8163ca9a>] dump_stack+0x54/0x74
[<
ffffffffa00c2c8e>] intel_dp_detect+0x1e/0x4b0 [i915]
[<
ffffffffa001913d>] status_show+0x3d/0x80 [drm]
[<
ffffffff813d5340>] dev_attr_show+0x20/0x60
[<
ffffffff81221f50>] ? sysfs_read_file+0x80/0x1b0
[<
ffffffff81221f79>] sysfs_read_file+0xa9/0x1b0
[<
ffffffff811aaf1e>] vfs_read+0x9e/0x170
[<
ffffffff811aba4c>] SyS_read+0x4c/0xa0
[<
ffffffff8164e392>] system_call_fastpath+0x16/0x1b
But if you add tons of memory checking debug options to your Kernel
you'll also see:
- general protection fault: 0000
- BUG kmalloc-4096 (Tainted: G D W ): Poison overwritten
- INFO: Allocated in intel_ddi_init+0x65/0x270 [i915]
- INFO: Freed in intel_dp_encoder_destroy+0x69/0xb0 [i915]
Among a bunch of other error messages.
So this commit just destroys the sysfs files before both the encoder
and connectors are freed.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Fri, 27 Sep 2013 12:10:44 +0000 (15:10 +0300)]
drm/i915/dp: do not write DP_TRAINING_PATTERN_SET all the time
Neither the DP spec nor the compliance test spec state or imply that we
should write the DP_TRAINING_PATTERN_SET at every voltage swing and
pre-emphasis change. Indeed we probably shouldn't. So don't.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49402
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Smoke-tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Fri, 20 Sep 2013 13:42:14 +0000 (16:42 +0300)]
drm/i915/dp: retry i2c-over-aux seven times on AUX DEFER
Per DP1.2 spec.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes [Fri, 27 Sep 2013 17:40:54 +0000 (10:40 -0700)]
drm/i915/vlv: reduce GT FIFO error info to a debug message
It indicates a probable BIOS bug, but it appears to be harmless, and
there's nothing the user can do about it anyway, so reduce to a debug
msg. I've filed a bug with the BIOS folks about it anyway, so hopefully
they'll fix whatever GT SB read they were doing when the GT was off.
References: https://bugs.freedesktop.org/show_bug.cgi?id=69396
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Fri, 27 Sep 2013 11:11:50 +0000 (12:11 +0100)]
drm: Reject stereo modes with an unknown layout
The kernel shouldn't accept invalid modes, just say No.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Fri, 27 Sep 2013 11:11:49 +0000 (12:11 +0100)]
drm: Revert "drm: Reject modes with more than 1 stereo flags set"
Now that the coding of stereo layout has changed from a bit field to an
enum, we need remove that check.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Fri, 27 Sep 2013 11:11:48 +0000 (12:11 +0100)]
drm: Code stereo layouts as an enum rather than a bit field
This allows us to use fewer bits in the mode structure, leaving room for
future work while allowing more stereo layouts types than we could have
ever dreamt of.
I also exposed the previously private DRM_MODE_FLAG_3D_MASK to set in
stone that we are using 5 bits for the stereo layout enum, reserving 32
values.
Even with that reservation, we gain 3 bits from the previous encoding.
The code adding the mandatory stereo modes needeed to be adapted as it was
relying or being able to or stereo layouts together.
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes [Fri, 27 Sep 2013 00:55:58 +0000 (17:55 -0700)]
drm/i915/vlv: use correct units for rc6 residency v2
We need to use the clock control reg to figure out how many CZ clks are in
30ns and use that as the basis for our RC6 residency calculations.
v2: use ULL everywhere for consistency (Chris)
factor out bias for clarity (Chris)
References: https://bugs.freedesktop.org/show_bug.cgi?id=69692
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes [Fri, 27 Sep 2013 00:55:57 +0000 (17:55 -0700)]
drm/i915/vlv: use lower precision RC6 counter
And add some reg defines while we're at it. Since the units of the RC6
residency counter are actually in CZ clocks, we want to just use the
high bits or we'll overflow too frequently.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 24 Sep 2013 18:26:19 +0000 (21:26 +0300)]
drm/i915: Use DIV_ROUND_CLOSEST()
vlv_find_best_dpll() has an open coded DIV_ROUND_CLOSEST(). Replace it
with the real thing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 24 Sep 2013 18:26:18 +0000 (21:26 +0300)]
drm/i915: Eliminate one indent leel from vlv_find_best_dpll
Use 'continue' to get rid of one indent level in vlv_find_best_dpll()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chon Ming Lee [Fri, 27 Sep 2013 07:31:00 +0000 (15:31 +0800)]
drm/i915: Program GMBUS Frequency based on the CDCLK for VLV.
CDCLK is used to generate the gmbus clock. This is normally done by
BIOS. Program the value if the BIOS-less system doesn't do it.
v2: Move this to intel_i2c_reset to allow reprogram the gmbus frequency
during resume. (Daniel)
v3: Change GMBUS_FREQ to GMBUSFREQ_VLV, and use VLV_DISPLAY_BASE.
(Ville).
Remove cdclk_ratio[] table, and calculate the cdclk ratio instead.
(Ville).
Change the shift then mask for reg read, to mask first, then shift.
(Ville).
Remove the gmbus frequency calculation = cdclk/1.01. Based on BIOS
programming, gmbus frequency = cdclk frequency. (Ville)
Add get_disp_clk_div, which can use to get cdclk/czclk divide.
v4: Fix the mmio_offset base for CZCLK_CDCLK_FREQ_RATIO, gmbus_freq
calculation, and duplicate check for gmbus_freq. (Ville)
In VLV, the spec is wrong about 4Mhz reference frequency for GMBUS. It
should be 1Mhz.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[danvet: Add the comment Ville suggested. Also appease checkpatch a
bit.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes [Wed, 25 Sep 2013 21:04:32 +0000 (14:04 -0700)]
drm/i915/vlv: hack to init backlight regs if BIOS fails to do so v2
Still digging up the actual VBT info for this, but wanted to get this
out there for testing, or in case others are also bugged by this.
This can happen if you boot with an external display connected. In that
case, the attached eDP backlight modulation frequency may not be
programmed, so we need to use something (in this case the value my BIOS
normally programs with just the internal display enabled).
v2: fix masking and magic value in read_blc_pwm_ctl (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67732
Tested-by: shui yangwei <yangweix.shui@intel.com> (v1)
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:40 +0000 (16:45 +0100)]
drm/i915: Allow stereo modes on HDMI
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:39 +0000 (16:45 +0100)]
drm/i915: Prefer crtc_{h|v}display for pipe src dimensions
Now that we ask to adjust the crtc timings for stereo modes, the correct
pipe_src_w and pipe_src_h can be found in crtc_vdisplay and crtc_hdisplay.
v2: Add comment about why pipe_src_w/h need to be set afert
set_crtcinfo() (Daniel Vetter)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:38 +0000 (16:45 +0100)]
drm/i915: Ask the DRM core do make stereo timings adjustements
When scanning out big stereo buffers that are actually bigger that their
natural 2D counterpart, we need to blow up the crtc timings as well.
Not that this is only done for frame packing as this is the only stereo
mode currently exposed needing this kind of ajdustements.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:37 +0000 (16:45 +0100)]
drm/i915: Use crtc_clock with the adjusted mode
struct drm_mode_display now has a separate crtc_ version of the clock to
be used when we're talking about the timings given to the harwadre (was
far as the mode is concerned).
This commit is really the result of a git grep adjusted_mode.*clock and
replacing those by adjusted_mode.crtc_clock. No functional change.
v2: Rebased on drm-intel-queued-next
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:36 +0000 (16:45 +0100)]
drm/i915: Use crtc_clock in intel_dump_crtc_timings()
We want to dump the parameters given to the hardware, so let's use
crtc_clock here.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:31 +0000 (16:45 +0100)]
drm: Check the fb size against the adjusted v/hdisplay for stereo modes
Some stereo modes, like frame packing, need a larger CRTC viewport than
the "natural" underlying 2D mode and thus drm_crtc_check_viewport()
needs to query the adjusted mode to use the correct h/vdisplay.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:30 +0000 (16:45 +0100)]
drm: Factor out common CRTC viewport checking code
Both setcrtc and page_flip are checking that the framebuffer is big
enough for the defined crtc viewport (x, y, hdisplay, vdisplay). Factor
that code out in a single function.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:35 +0000 (16:45 +0100)]
drm: Implement timings adjustments for frame packing
When using the frame packing and a single big framebuffer, some hardware
requires that we do everything like if we were scanning out the big
buffer itself. Let's instrument drm_mode_set_crtcinfo() to be able to do
this adjustement if the driver is asking for it.
v2: Use crtc_vtotal and multiply the clock by 2 instead of
reconstructing it (Ville Syrjälä)
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:34 +0000 (16:45 +0100)]
drm: Introduce a crtc_clock for struct drm_display_mode
Just like the various timings, make it possible to have a clock field
what we can tweak before giving it to hardware.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:33 +0000 (16:45 +0100)]
drm: Remove synth_clock from struct drm_display_mode
This field is unused. Garbage collect it.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:32 +0000 (16:45 +0100)]
drm: Remove clock_index from struct drm_display_mode
This field was only accessed by the nouveau driver, but never set. So
concluded we can rid of this one.
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:29 +0000 (16:45 +0100)]
drm: Make exposing stereo modes a per-connector opt-in
Just like with interlaced or double scan modes, make stereo modes a
per-connector opt-in to give a chance to driver authors to make it work
before enabling it.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:28 +0000 (16:45 +0100)]
drm: Carry over the stereo flags when adding the alternate mode
This allows to expose the alternate clock versions of the stereo modes.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:27 +0000 (16:45 +0100)]
drm: Make drm_match_cea_mode() return the underlying 2D VIC for 3d modes
When scanning out a stereo mode, the AVI infoframe vic field has to be
the underlyng 2D VIC. Before that commit, we weren't matching the CEA
mode because of the extra stereo flag and then were setting the VIC
field in the AVI infoframe to 0.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:26 +0000 (16:45 +0100)]
drm: Set the relevant infoframe field when scanning out a 3D mode
When scanning out a 3D mode on HDMI, we need to send an HDMI infoframe
with the corresponding layout to the sink.
v2: Make s3d_structure_from_display_mode() less subtle (Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:25 +0000 (16:45 +0100)]
drm: Reject modes with more than 1 stereo flags set
When setting a stereo 3D mode, there can be only one bit set describing
the layout of the frambuffer(s). So reject invalid modes early.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:24 +0000 (16:45 +0100)]
drm: Extract add_hdmi_mode() out of do_hdmi_vsdb_modes()
So we respect a nice design of having similar functions at the same
level, in this case:
do_hdmi_vsdb_modes()
- add_hdmi_mandatory_stereo_modes()
- add_hdmi_mode()
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:23 +0000 (16:45 +0100)]
drm/edid: Expose mandatory stereo modes for HDMI sinks
For now, let's just look at the 3D_present flag of the CEA HDMI vendor
block to detect if the sink supports a small list of then mandatory 3D
formats.
See the HDMI 1.4a 3D extraction for detail:
http://www.hdmi.org/manufacturer/specification.aspx
v2: Rename freq to vrefresh, make the mandatory structure a bit more
compact, fix some white space issues and add a couple of const
(Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:22 +0000 (16:45 +0100)]
drm: Add a STEREO_3D capability to the SET_CLIENT_CAP ioctl
This capability allows user space to control the delivery of modes with
the 3D flags set. This is to not play games with current user space
users not knowing anything about stereo 3D flags and that could try
to set a mode with one or several of those bits set.
So, the plan is to remove the stereo modes from the list of modes we
give to DRM clients by default, and let them through if we are being
told otherwise.
stereo_allowed is bound to the drm_file structure to make it a
per-client setting, not a global one.
v2: Replace clearing 3D flags by discarding the stereo modes now that
they are regular modes.
v3: SET_CAP -> SET_CLIENT_CAP rename (Chris Wilson)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:21 +0000 (16:45 +0100)]
drm: Add HDMI stereo 3D flags to struct drm_mode_modeinfo
HDMI 1.4a defines a few layouts that we'd like to expose. This commits
add new modeinfo flags that can be used to list the supported stereo
layouts (when querying the list of modes) and to set a given stereo 3D
mode (when setting a mode).
v2: Add a drm_mode_is_stereo() helper
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:20 +0000 (16:45 +0100)]
drm: Add a SET_CLIENT_CAP ioctl
This ioctl can be used to turn some knobs in a DRM driver. The client
can ask the DRM core for an alternate view of the reality: it can be
useful to be able to instruct the core that the DRM client can handle
new functionnality that would otherwise break current ABI.
v2: Rename to ioctl from SET_CAP to SET_CLIENT_CAP (Chris Wilson)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 25 Sep 2013 15:45:19 +0000 (16:45 +0100)]
drm: Move the GET_CAP macros next to the corresponding ioctl structure
It's a tiny bit more logical to find the different capabilities you can
use with the GET_CAP ioctl next to the structure rather than putting
them at the end of the file.
v2: Tab align the litterals (David Herrmann)
v3: Make it clearer that DRM_PRIME_CAP_EXPORT/IMPORT are flags of
DRM_CAP_PRIME.
v4: Rebase on top of latest bits (DRM_CAP_ASYNC_PAGE_FLIP was
introduced)
Reviewed-by: David Herrmann <dh.herrmann@gmail.com> (for v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 25 Sep 2013 21:24:01 +0000 (14:24 -0700)]
drm/i915/vlv: fix up broken precision in vlv_crtc_clock_get
With some divider values we end up with the wrong result. So remove the
intermediates (like Ville suggested in the first place) to get the right
answer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes [Fri, 20 Sep 2013 18:29:32 +0000 (11:29 -0700)]
drm/i915/vlv: add VLV specific clock_get function v3
Calculation is a little different than other platforms.
v2: update to use port_clock instead
rebase on top of Ville's changes
v3: update to new port_clock semantics - don't divide by
pixel_multiplier (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=67345
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 25 Sep 2013 10:43:28 +0000 (11:43 +0100)]
drm/i915: Add a tracepoint for using a semaphore
So that we can find the callers who introduce a ring stall. A single
ring stall is not too unwelcome, the right issue becomes when they start
to interlock and prevent any concurrent work. That, however, is a little
tricker to detect with a mere tracepoint!
v2: Rebrand it as a ring event, rather than an object event.
v3: Include the seqno in the tracepoint for posterity or something.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 25 Sep 2013 09:23:19 +0000 (10:23 +0100)]
drm/i915: Show WT caching in debugfs
Add the missing cache-level to the describe_obj() function for debug and
error reporting.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chon Ming Lee [Wed, 25 Sep 2013 07:47:51 +0000 (15:47 +0800)]
drm/i915: Fix VLV eDP timing v2
Fix the typo in previous commit for DP 1.62 divisor.
drm/i915: Move Valleyview DP DPLL divisor calc to intel_dp_set_clock v2
v2: sigh, the m1 div is 3.
Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 23 Sep 2013 20:33:19 +0000 (17:33 -0300)]
drm/i915: Move the conditional seqno query into the tracepoint
We only wish to know the value of seqno when emitting the tracepoint, so
move the query from a parameter to the macro to inside the conditional
macro body so that the query is only evaluated when required.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Tue, 24 Sep 2013 16:57:58 +0000 (09:57 -0700)]
drm/i915: Convert active API to VMA
Even though we track object activity and not VMA, because we have the
active_list be based on the VM, it makes the most sense to use VMAs in
the APIs.
NOTE: Daniel intends to eventually rip out active/inactive LRUs, but for
now, leave them be.
v2: Remove leftover hunk from the previous patch which didn't keep
i915_gem_object_move_to_active. That patch had to rely on the ring to
get the dev instead of the obj. (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Tue, 24 Sep 2013 16:57:57 +0000 (09:57 -0700)]
drm/i915: Provide a cheap ggtt vma lookup
"We do fairly often lookup the ggtt vma for an obj." - Chris Wilson. As
such, provide a function to offer slightly cheaper access to the vma.
Not performance tested. By my quick estimation it saves at least 3
pointer dereferences from the existing mechanism.
This patch mostly matches code from Chris in
<
20130911221430.GB7825@nuc-i3427.alporthouse.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Tue, 24 Sep 2013 16:57:56 +0000 (09:57 -0700)]
drm/i915: trace vm eviction instead of everything
Tracing vm eviction is really the event we care about. For the cases we
evict everything, we still will get the trace.
v2: Add the drm device to the trace since we might not be the only
device in the system. (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 24 Sep 2013 18:48:31 +0000 (15:48 -0300)]
drm/i915: remove "extern" keywords from intel_drv.h functions
Since I already reorganized the header file, Daniel requested me to
remove those keywords. It seems "checkpath.pl --strict" also doesn't
like "extern" on header files.
At least now we're consistent :)
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 24 Sep 2013 16:52:57 +0000 (13:52 -0300)]
drm/i915: make hsw_{disable, restore}_lcpll static
These functions were added before the final PC8 implementation, and
their callers moved to intel_display.c during the code review.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 24 Sep 2013 16:52:56 +0000 (13:52 -0300)]
drm/i915: make intel_crtc_fb_gamma_{set, get} static
By moving them to intel_fb.c.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 24 Sep 2013 16:52:55 +0000 (13:52 -0300)]
drm/i915: make intel_crtc_load_lut static
And move it so it doesn't need a forward declaration.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 24 Sep 2013 16:52:54 +0000 (13:52 -0300)]
drm/i915: make intel_pipe_has_type static
Also move it to the top of the file so we can remove the forward
declaration.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 24 Sep 2013 16:52:53 +0000 (13:52 -0300)]
drm/i915: reorganize intel_drv.h
Daniel complained that we keep adding stuff to the bottom of the file,
so we constantly have conflicts. So reorganize everything and split
them file-by-file, also sorting the files in alphabetical order. This
way, patches touching different files will have a smaller chance of
conflicting. Of course, this commit will conflict with everybody on
the list :)
Also remove a few useless comments and make some things fit into 80
lines.
v2: - Conflict with intel_ddi_get_config
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Tue, 24 Sep 2013 13:44:39 +0000 (16:44 +0300)]
drm/i915: backlight combination mode bit is gen4 only
Not valid for later non-PCH split platforms such as VLV.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 24 Sep 2013 11:24:05 +0000 (14:24 +0300)]
drm/i915: Add HSW CRT output readout support
Call intel_ddi_get_config() to get the pipe_bpp settings from
DDI.
The sync polarity settings from DDI are irrelevant for CRT
output, so override them with data from the ADPA register.
v2: Extract intel_crt_get_flags()
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69691
Tested-by: Qingshuai Tian <qingshuai.tian@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Fri, 13 Sep 2013 08:03:09 +0000 (11:03 +0300)]
drm/i915: clean up and simplify i9xx_crtc_mode_set wrt PLL handling
Flat out skip anything to do with PLL if we have a DSI encoder (and thus
DSI PLL). Also skip PLL computation if the encoder has already set
clocks. This allows for some tidying up of the code, including a
superfluous call to intel_limit() for LVDS downclock path.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Tue, 24 Sep 2013 11:55:40 +0000 (12:55 +0100)]
drm/i915: Add some debug spam for intialising SDVO
During SDVO initialisation it would be useful to a have a record of the
individual devices we try to enable and later probe - in particular to
be able to see which fail.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 26 Aug 2013 12:46:09 +0000 (13:46 +0100)]
drm/i915: Delay the release of the forcewake by a jiffie
Obtaining the forcwake requires expensive and time consuming
serialisation. And we often try to obtain the forcewake multiple times
in very quick succession. We can reduce the overhead of these sequences
by delaying the forcewake release, and so not hammer the hw quite so
hard.
I was hoping this would help with the spurious
[drm:__gen6_gt_force_wake_mt_get] *ERROR* Timed out waiting for forcewake old ack to clear.
found on Haswell. Alas not.
v2: Fix teardown ordering - unmap the regs after turning off forcewake,
and make sure we do turn off forcewake - both found by Ville.
v3: As we introduce intel_uncore_fini(), use it to make sure everything
is disabled before we hand back to the BIOS.
Note: I have no claims for improved performance, stablity or power
comsumption for this patch. We should not be hitting the registers often
enough for this to improve benchmarks, but given the nature of our hw it
is likely to improve long term stability.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dan Carpenter [Tue, 24 Sep 2013 07:57:35 +0000 (10:57 +0300)]
drm/i915: precendence bug in GT_PARITY_ERROR()
The | operation has higher precedence than "?:" so the macro always
returns GT_RENDER_L3_PARITY_ERROR_INTERRUPT_S1.
This regression has been introduce in "drm/i915: Add second slice l3
remapping".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 23 Sep 2013 14:48:20 +0000 (17:48 +0300)]
drm/i915: Fix intel_crtc_mode_get() mode clock
i9xx_crtc_clock_get() no longer populates adjusted_mode.clock, so we
must get the pixel clock from port_clock in intel_crtc_mode_get().
This bug caused Chris's 845g machine to lockup during boot, and it
was introduced in:
commit
18442d08786472c63a0a80c27f92b033dffc26de
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Sep 13 16:00:08 2013 +0300
drm/i915: Fix port_clock and adjusted_mode.clock readout all over
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69713
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Fri, 20 Sep 2013 16:35:30 +0000 (09:35 -0700)]
drm/i915: Calculate PSR register offsets from base + gen
Future generations will be changing these registers (thanks to design
for giving us an early heads up). To help abstract, create the
definition of the base of the register block, and define all registers
relative to that.
Design has promised to not change the offsets relative to the base.
v2: Also change IS_HASWELL checks to HAS_PSR
CC: Rodrigo Vivi <rodrigo.vivi@gmail.com>
CC: Intel GFX <intel-gfx@lists.freedesktop.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Fri, 20 Sep 2013 13:42:17 +0000 (16:42 +0300)]
drm/i915/dp: read DPCD PSR capability only on eDP
Reduce AUX transactions for non-eDP.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 16 Sep 2013 14:38:37 +0000 (17:38 +0300)]
drm/i915: Drop explicit plane restoration during resume
We already restore planes during the modeset operation, so no need to do
another loop over the planes and try to restore them again.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 16 Sep 2013 14:38:36 +0000 (17:38 +0300)]
drm/i915: Call intel_uncore_early_sanitize() during resume
Call intel_uncore_early_sanitize() first thing during resume to prevent
stale BIOS leftovers from being reported as unclaimed register access.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 16 Sep 2013 14:38:35 +0000 (17:38 +0300)]
drm/i915: Move power well resume earlier
i915_restore_state() -> i915_restore_display() will attempt to
re-disable VGA during resume. So the power well needs to be powered on
before that.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 16 Sep 2013 14:38:34 +0000 (17:38 +0300)]
drm/i915: Move power well init earlier during driver load
intel_modeset_init() will already attempt to disable VGA. In order to do
that, it needs the power well to be on. So move the power well init
to happen before intel_modeset_init() during driver load.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 16 Sep 2013 14:38:33 +0000 (17:38 +0300)]
drm/i915: Redisable VGA before the modeset on resume
The VGA plane needs to be disabled before we start doing any
modeset operations on resume.
This should also guarantee that the power well will be enabled
when we call i915_redisable_vga() since it gets explicitly powered on
during resume, and will get powered back off during the modeset
operation if no longer needed.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 20 Sep 2013 07:14:23 +0000 (10:14 +0300)]
drm/i915: Fix unclaimed register access due to delayed VGA memory disable
VGA registers live inside the power well on HSW, so in order to write
the VGA MSR register we need the power well to be on.
We really must write to the register to properly clear the
VGA_MSR_MEM_EN enable bit, even if all VGA registers get zeroed when
the power well is down. It seems that the implicit zeroing done by
the power well is not enough to propagate the VGA_MSR_MEM_EN bit to
whomever is actually responsible for the memory decode ranges.
If we leave VGA memory decode enabled, and then turn off the power well,
all VGA memory reads will return zeroes. But if we first disable VGA
memory deocde and then turn off the power well, VGA memory reads
return all ones, indicating that the access wasn't claimed by anyone.
For the vga arbiter to function correctly the IGD must not claim the
VGA memory accesses.
Previously we were doing the VGA_MSR register access while the power well
was excplicitly powered up during driver init. But ever since
commit
6e1b4fdad5157bb9e88777d525704aba24389bee
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Sep 5 20:40:52 2013 +0300
drm/i915: Delay disabling of VGA memory until vgacon->fbcon handoff is done
we delay the VGA memory disable until fbcon has initialized, and so
there's a possibility that the power well got turned off during the
fbcon modeset. Also vgacon_save_screen() will need the power well to be
on to be able to read the VGA memory.
So immediately after enabling the power well during init grab a refence
for VGA purposes, and after all the VGA handling is done, release it.
v2: Add intel_display_power_put() for the num_pipes==0 case
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix up the patch wiggle screw-up that I've done and which
Paulo catched. Also polish spelling in the patch headline.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Fri, 20 Sep 2013 22:48:39 +0000 (00:48 +0200)]
drm/i915: Rip out SUPPORTS_EDP
It only controls the setting of the vbt.edp_support variable, which in
turn only controls one debug output plus can also force-disable the
lvds output.
Since the value only restricted this logic to mobile ilk there's the
slight risk that this will break lvds on desktop ilk or on snb/ivb
platforms. But with the vbt it's better when we know what's going on
here, so let's rip it out and see what happens.
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 12 Sep 2013 20:12:18 +0000 (17:12 -0300)]
drm/i915: don't init DP or HDMI when not supported by DDI port
There's no reason to init a DP connector if the encoder just supports
HDMI: we'll just waste hundreds and hundreds of cycles trying to do DP
AUX transactions to detect if there's something there. Same goes for a
DP connector that doesn't support HDMI, but I'm not sure these
actually exist.
v2: - Use bit fields
- Remove useless identation level
- Replace DRM_ERROR with DRM_DEBUG_KMS
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 12 Sep 2013 20:10:11 +0000 (17:10 -0300)]
drm/i915: add some assertions about VBT DDI port types
Our code makes a lot of assumptions regarding what each DDI port
actually supports, and the VBT should tell us what is really happening
in the hardware. So parse the information provided by the VBT and
check if any of our assumptions is wrong.
Our driver also has a history of not really trusting the VBT, so a
WARN here could mean that:
a) our coding assumptions are wrong
b) the VBT is wrong
c) we're incorrectly parsing the VBT
d) the checks are wrong
But I really hope we won't ever trigger any of those WARNs.
v2: Don't check the redundant "Capabilities" field from byte 24 since
it doesn't seem to be used.
v3: Rebase
v4: Replace WARN with DRM_DEBUG_KMS
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 12 Sep 2013 20:07:55 +0000 (17:07 -0300)]
drm/i915: check the DDC and AUX bits of the VBT on DDI machines
Our code currently assumes that port X will use the DP AUX channel X
and the DDC pin X. The VBT should tell us how things are mapped, so
add some WARNs in case we discover our assumptions are wrong (or in
case the VBT is just wrong, which is also perfectly possible).
Why would someone wire port B to AUX C and DDC D?
v2: Rebase
v3: Convert WARNs to DRM_DEBUG_KMS
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 12 Sep 2013 20:06:24 +0000 (17:06 -0300)]
drm/i915: use the HDMI DDI buffer translations from VBT
We currently use the recommended values from BSpec, but the VBT
specifies the correct value to use for the hardware we have, so use
it. We also fall back to the recommended value in case we can't find
the VBT.
In addition, this code also provides some infrastructure to parse more
information about the DDI ports. There's a lot more information we
could extract and use in the future.
v2: - Move some code to init_vbt_defaults.
v3: - Rebase
- Clarify the "DVO Port" matching code
v4: - Use I915_MAX_PORTS
- Change the HAS_DDI checks
- Replace DRM_ERROR with DRM_DEBUG_KMS
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Wed, 11 Sep 2013 21:02:47 +0000 (18:02 -0300)]
drm/i915: VBT's child_device_config changes over time
We currently treat the child_device_config as a simple struct, but
this is not correct: new BDB versions change the meaning of some
offsets, so the struct needs to be adjusted for each version.
Since there are too many changes (today we're in version 170!), making
a big versioned union would be too complicated, so child_device_config
is now a union of 3 things: (i) a "raw" byte array that's safe to use
anywhere; (ii) an "old" structure that's the one we've been using and
should be safe to keep in the SDVO and TV code; and (iii) a "common"
structure that should contain only fields that are common for all the
known VBT versions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 13 Sep 2013 22:57:04 +0000 (23:57 +0100)]
drm/i915: Do not unlock upon error in i915_gem_idle()
We never took the lock ourselves and all callers expect the struct_mutex
to be locked upon return (be it success or error), thereore dropping the
lock along the error paths looks to be a vestigial error from
commit
db1b76ca6a79c774074ae87bee7afc0825a478f5
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jul 9 16:51:37 2013 +0200
drm/i915: don't frob mm.suspended when not using ums
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 19 Sep 2013 12:00:11 +0000 (14:00 +0200)]
drm/i915: Use unsigned for overflow checks in execbuf
There's actually no real risk since we already check for stricter
constraints earlier (using UINT_MAX / sizeof (struct
drm_i915_gem_exec_object2) as the limit). But in eb_create we use
signed integers, which steals a factor of 2. Luckily struct
drm_i915_gem_exec_object2 for this to not matter.
Still, be consistent and use unsigned integers.
Similar use unsinged integers when checking for overflows in the
relocation entry processing.
I've also added a new subtests to igt/gem_reloc_overflow to also
test for overflowing args->buffer_count values.
v2: Give the variables again tighter scope to make it clear that the
computation is purely local and doesn't leak out to the 2nd block.
Requested by Chris Wilson.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 19 Sep 2013 12:05:45 +0000 (14:05 +0200)]
drm/i915: Ditch INTELFB_CONN_LIMIT
And the gratious overallocation of crtcs. Seems to go back to the ums
days of yonder ...
We also still need it to make the fbdev emulation happy, but I don't
think there's really a need. Especially since the current fbdev
emulation doesn't actually support cloning.
v2: Use sizeof(*pointer) pattern (Jani).
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Fri, 20 Sep 2013 22:35:38 +0000 (00:35 +0200)]
drm/i915: Use kcalloc more
No buffer overflows here, but better safe than sorry.
v2:
- Fixup the sizeof conversion, I've missed the pointer deref (Jani).
- Drop the redundant GFP_ZERO, kcalloc alreads memsets (Jani).
- Use kmalloc_array for the execbuf fastpath to avoid the memset
(Chris). I've opted to leave all other conversions as-is since they
aren't in a fastpath and dealing with cleared memory instead of
random garbage is just generally nicer.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop the contentious kmalloc_array hunk in execbuf.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 19 Sep 2013 10:18:32 +0000 (12:18 +0200)]
drm/i915: use pointer = k[cmz...]alloc(sizeof(*pointer), ...) pattern
Done while reviewing all our allocations for fubar. Also a few errant
cases of lacking () for the sizeof operator - just a bit of OCD.
I've left out all the conversions that also should use kcalloc from
this patch (it's only 2).
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Airlie [Tue, 1 Oct 2013 00:00:50 +0000 (10:00 +1000)]
Merge tag 'drm-intel-next-2013-09-21-merged' of git://people.freedesktop.org/~danvet/drm-intel into drm-next
drm-intel-next-2013-09-21:
- clock state handling rework from Ville
- l3 parity handling fixes for hsw from Ben
- some more watermark improvements from Ville
- ban badly behaved context from Mika
- a few vlv improvements from Jesse
- VGA power domain handling from Ville
drm-intel-next-2013-09-06:
- Basic mipi dsi support from Jani. Not yet converted over to drm_bridge
since that was too fresh, but the porting is in progress already.
- More vma patches from Ben, this time the code to convert the execbuffer
code. Now that the shrinker recursion bug is tracked down we can move
ahead here again. Yay!
- Optimize hw context switching to not generate needless interrupts (Chris
Wilson). Also some shuffling for the oustanding request allocation.
- Opregion support for SWSCI, although not yet fully wired up (we need a
bit of runtime D3 support for that apparently, due to Windows design
deficiencies), from Jani Nikula.
- A few smaller changes all over.
[airlied: merge conflict fix in i9xx_set_pipeconf]
* tag 'drm-intel-next-2013-09-21-merged' of git://people.freedesktop.org/~danvet/drm-intel: (119 commits)
drm/i915: assume all GM45 Acer laptops use inverted backlight PWM
drm/i915: cleanup a min_t() cast
drm/i915: Pull intel_init_power_well() out of intel_modeset_init_hw()
drm/i915: Add POWER_DOMAIN_VGA
drm/i915: Refactor power well refcount inc/dec operations
drm/i915: Add intel_display_power_{get, put} to request power for specific domains
drm/i915: Change i915_request power well handling
drm/i915: POSTING_READ IPS_CTL before waiting for the vblank
drm/i915: don't disable ERR_INT on the IRQ handler
drm/i915/vlv: disable rc6p and rc6pp residency reporting on BYT
drm/i915/vlv: honor i915_enable_rc6 boot param on VLV
drm/i915: s/HAS_L3_GPU_CACHE/HAS_L3_DPF
drm/i915: Do remaps for all contexts
drm/i915: Keep a list of all contexts
drm/i915: Make l3 remapping use the ring
drm/i915: Add second slice l3 remapping
drm/i915: Fix HSW parity test
drm/i915: dump crtc timings from the pipe config
drm/i915: register backlight device also when backlight class is a module
drm/i915: write D_COMP using the mailbox
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Linus Torvalds [Sun, 29 Sep 2013 22:02:38 +0000 (15:02 -0700)]
Linux 3.12-rc3
Linus Torvalds [Sun, 29 Sep 2013 20:47:35 +0000 (13:47 -0700)]
Merge tag 'usb-3.12-rc3' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB driver fixes for 3.12-rc3.
These are all for host controller issues that have been reported, and
there's a fix for an annoying error message that gets printed every
time you remove a USB 3 device from the system that's been bugging me
for a while"
* tag 'usb-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: dwc3: add support for Merrifield
USB: fsl/ehci: fix failure of checking PHY_CLK_VALID during reinitialization
USB: Fix breakage in ffs_fs_mount()
fsl/usb: Resolve PHY_CLK_VLD instability issue for ULPI phy
usb/core/devio.c: Don't reject control message to endpoint with wrong direction bit
usb: chipidea: USB_CHIPIDEA should depend on HAS_DMA
usb: chipidea: udc: free pending TD at removal procedure
usb: chipidea: imx: Add usb_phy_shutdown at probe's error path
usb: chipidea: Fix memleak for ci->hw_bank.regmap when removal
usb: chipidea: udc: fix the oops after rmmod gadget
USB: fix PM config symbol in uhci-hcd, ehci-hcd, and xhci-hcd
USB: OHCI: accept very late isochronous URBs
USB: UHCI: accept very late isochronous URBs
USB: iMX21: accept very late isochronous URBs
usbcore: check usb device's state before sending a Set SEL control transfer
xhci: Fix race between ep halt and URB cancellation
usb: Fix xHCI host issues on remote wakeup.
xhci: Ensure a command structure points to the correct trb on the command ring
xhci: Fix oops happening after address device timeout
Linus Torvalds [Sun, 29 Sep 2013 20:47:00 +0000 (13:47 -0700)]
Merge tag 'tty-3.12-rc3' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some serial at tty driver fixes for 3.12-rc3
The serial driver fixes some kref leaks, documentation is moved to the
proper places, and the tty and n_tty fixes resolve some reported
regressions. There is still one outstanding tty regression fix that
isn't in here yet, as I want to test it out some more, it will be sent
for 3.12-rc4 if it checks out"
* tag 'tty-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: ar933x_uart: move devicetree binding documentation
tty: Fix SIGTTOU not sent with tcflush()
n_tty: Fix EOF push index when termios changes
serial: pch_uart: remove unnecessary tty_port_tty_get
serial: pch_uart: fix tty-kref leak in dma-rx path
serial: pch_uart: fix tty-kref leak in rx-error path
serial: tegra: fix tty-kref leak
Linus Torvalds [Sun, 29 Sep 2013 20:46:18 +0000 (13:46 -0700)]
Merge tag 'staging-3.12-rc3' of git://git./linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some staging driver fixes, MAINTAINER updates, and a new
device id. All of these have been in the linux-next tree, and are
pretty simple patches"
* tag 'staging-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Add new device ID
staging: imx-drm: Fix probe failure
staging: vt6656: [BUG] iwctl_siwencodeext return if device not open
staging: vt6656: [BUG] main_usb.c oops on device_close move flag earlier.
staging: vt6656: rxtx.c [BUG] s_vGetFreeContext dead lock on null apTD.
Staging: rtl8192u: r819xU_cmdpkt: checking NULL value after doing dev_alloc_skb
staging: usbip: Orphan usbip
staging: r8188eu: Add files for new drive: Cocci spatch "noderef"
staging: r8188eu: Cocci spatch "noderef"
staging: octeon-usb: Cocci spatch "noderef"
staging: r8188eu: Add files for new drive: Cocci spatch "noderef"
MAINTAINERS: staging: dgnc and dgap drivers: add maintainer
staging: lustre: Cocci spatch "noderef"
Linus Torvalds [Sun, 29 Sep 2013 20:45:23 +0000 (13:45 -0700)]
Merge tag 'driver-core-3.12-rc3' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver core / sysfs fixes from Greg KH:
"Here are 2 fixes for 3.12-rc3. One fixes a sysfs problem with
mounting caused by 3.12-rc1, and the other is a bug reported by the
chromeos developers with the driver core.
Both have been in linux-next for a bit"
* tag 'driver-core-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core : Fix use after free of dev->parent in device_shutdown
sysfs: Allow mounting without CONFIG_NET
Linus Torvalds [Sun, 29 Sep 2013 20:44:48 +0000 (13:44 -0700)]
Merge tag 'char-misc-3.12-rc3' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some HyperV and MEI driver fixes for 3.12-rc3. They resolve
some issues that people have been reporting for them"
* tag 'char-misc-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: Terminate vmbus version negotiation on timeout
Drivers: hv: util: Correctly support ws2008R2 and earlier
mei: cancel stall timers in mei_reset
mei: bus: stop wait for read during cl state transition
mei: make me client counters less error prone
Linus Torvalds [Sun, 29 Sep 2013 17:04:03 +0000 (10:04 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf revert from Ingo Molnar:
"This fixes the 'perf top' regression Markus Trippelsdorf reported"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "perf symbols: Demangle cloned functions"
Linus Torvalds [Sun, 29 Sep 2013 17:02:40 +0000 (10:02 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too major, radeon still has some dpm changes for off by
default.
Radeon, intel, msm:
- radeon: a few more dpm fixes (still off by default), uvd fixes
- i915: runtime warn backtrace and regression fix
- msm: iommu changes fallout"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (27 commits)
drm/msm: use drm_gem_dumb_destroy helper
drm/msm: deal with mach/iommu.h removal
drm/msm: Remove iommu include from mdp4_kms.c
drm/msm: Odd PTR_ERR usage
drm/i915: Fix up usage of SHRINK_STOP
drm/radeon: fix hdmi audio on DCE3.0/3.1 asics
drm/i915: preserve pipe A quirk in i9xx_set_pipeconf
drm/i915/tv: clear adjusted_mode.flags
drm/i915/dp: increase i2c-over-aux retry interval on AUX DEFER
drm/radeon/cik: fix overflow in vram fetch
drm/radeon: add missing hdmi callbacks for rv6xx
drm/i915: Use a temporary va_list for two-pass string handling
drm/radeon/uvd: lower msg&fb buffer requirements on UVD3
drm/radeon: disable tests/benchmarks if accel is disabled
drm/radeon: don't set default clocks for SI when DPM is disabled
drm/radeon/dpm/ci: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/si: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/ni: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/btc: filter clocks based on voltage/clk dep tables
drm/radeon/dpm: fetch the max clk from voltage dep tables helper
...
Ingo Molnar [Sun, 29 Sep 2013 14:12:54 +0000 (16:12 +0200)]
Revert "perf symbols: Demangle cloned functions"
This reverts commit
de95ab53645a2f0015e0f68ee723f18dce2b8b51.
Markus Trippelsdorf reported that this commit broke 'perf top':
> I just see a gray screen with no text at all. Sometimes the
> following error messages are printed:
>
> *** Error in `perf': invalid fastbin entry (free): 0x00000000029b18c0
> ***
> *** Error in `perf': malloc(): memory corruption (fast): 0x0000000000ee0b10 ***
While this code is fixable, the commit itself fails on several levels:
- it should have been a separate helper function
- why the heck does it do strchr() twice
- it casts a const char * over into char *
- sloppy style
- it's not even a regression fix!
So lets revert it and re-try the patch in v3.13.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Airlie [Sun, 29 Sep 2013 00:06:28 +0000 (10:06 +1000)]
Merge branch 'msm-fixes-3.12-rc2' of git://people.freedesktop.org/~robclark/linux into drm-fixes
A small fix + deal with fallout of iommu changes + use new
drm_gem_dumb_destroy helper.
* 'msm-fixes-3.12-rc2' of git://people.freedesktop.org/~robclark/linux:
drm/msm: use drm_gem_dumb_destroy helper
drm/msm: deal with mach/iommu.h removal
drm/msm: Remove iommu include from mdp4_kms.c
drm/msm: Odd PTR_ERR usage
Linus Torvalds [Sat, 28 Sep 2013 21:22:17 +0000 (14:22 -0700)]
Merge branches 'sched-urgent-for-linus', 'timers-urgent-for-linus' and 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler, timer and x86 fixes from Ingo Molnar:
- A context tracking ARM build and functional fix
- A handful of ARM clocksource/clockevent driver fixes
- An AMD microcode patch level sysfs reporting fixlet
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm: Fix build error with context tracking calls
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: em_sti: Set cpu_possible_mask to fix SMP broadcast
clocksource: of: Respect device tree node status
clocksource: exynos_mct: Set IRQ affinity when the CPU goes online
arm: clocksource: mvebu: Use the main timer as clock source from DT
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode/AMD: Fix patch level reporting for family 15h
Linus Torvalds [Sat, 28 Sep 2013 21:21:13 +0000 (14:21 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"A couple of tooling fixlets and a PMU detection printout fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix PMU detection printout when no PMU is detected
perf symbols: Demangle cloned functions
perf machine: Fix path unpopulated in machine__create_modules()
perf tools: Explicitly add libdl dependency
perf probe: Fix probing symbols with optimization suffix
perf trace: Add mmap2 handler
perf kmem: Make it work again on non NUMA machines
Linus Torvalds [Sat, 28 Sep 2013 20:52:05 +0000 (13:52 -0700)]
Merge tag 'xfs-for-linus-v3.12-rc3' of git://oss.sgi.com/xfs/xfs
Pull xfs bugfixes from Ben Myers:
- fix for directory node collapse regression
- fix for recovery over stale on disk structures
- fix for eofblocks ioctl
- fix asserts in xfs_inode_free
- lock the ail before removing an item from it
* tag 'xfs-for-linus-v3.12-rc3' of git://oss.sgi.com/xfs/xfs:
xfs: fix node forward in xfs_node_toosmall
xfs: log recovery lsn ordering needs uuid check
xfs: fix XFS_IOC_FREE_EOFBLOCKS definition
xfs: asserting lock not held during freeing not valid
xfs: lock the AIL before removing the buffer item