OSDN Git Service
Adrian Hunter [Tue, 4 Nov 2014 10:42:37 +0000 (12:42 +0200)]
mmc: sdhci: Fix ADMA table size warning
The intent of the warning is to warn if the ADMA table
overflows. However there can be one more 'end' entry
so the condition should be adjusted accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Tue, 4 Nov 2014 10:42:36 +0000 (12:42 +0200)]
mmc: sdhci: Fix ADMA page boundary warnings
Bytes are being copied from/to a single page. The intent
of the warning is to warn if the page boundary is crossed.
There are two problems. First, PAGE_MASK is mistaken for
(PAGE_SIZE - 1). Secondly, instead of using the number
of bytes to copy, the warning is using the maximum that
that value could be. Fix both.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Tue, 4 Nov 2014 10:42:35 +0000 (12:42 +0200)]
mmc: sdhci: Fix incorrect ADMA2 descriptor table size
The ADMA2 descriptor table size was being calculated incorrectly
Fix it.
Note that it has been wrong for a long time and likely has not
caused any problems because of a combination of 1) not needing
alignment descriptors for block operations 2) more memory being
allocated than was requested 3) the use of
SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC which does not use an extra
descriptor for the end marker.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Timo Kokkonen [Mon, 3 Nov 2014 11:12:59 +0000 (13:12 +0200)]
mmc: host: atmel-mci: Add support for non-removable slots
Add support for non-removable slots which have no card detection GPIO
and which should not be polled for a card change.
Signed-off-by: Timo Kokkonen <timo.kokkonen@offcode.fi>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sebastian Hesselbarth [Tue, 21 Oct 2014 09:22:41 +0000 (11:22 +0200)]
mmc: sdhci-pxav3: Document clocks and additional clock-names property
Now that sdhci-pxav3 driver allows to have more than one IP clock defined,
document both clocks and clock-names properties.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sebastian Hesselbarth [Tue, 21 Oct 2014 09:22:40 +0000 (11:22 +0200)]
mmc: sdhci-pxav3: Get optional core clock
Besides the I/O clock, some PXAv3 SDHCI IP also requires a core clock to
be enabled. Add an optional core clock to the corresponding driver.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sebastian Hesselbarth [Tue, 21 Oct 2014 09:22:39 +0000 (11:22 +0200)]
mmc: sdhci-pxav3: Try to get named I/O clock first
With support for more than one clock, we'll need to distinguish between
the clock by name. Change clock probing to first try to get "io" clock
before falling back to unnamed clock.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sebastian Hesselbarth [Tue, 21 Oct 2014 09:22:38 +0000 (11:22 +0200)]
mmc: sdhci-pxav3: Move I/O clock to private data
As we are using references to the I/O clock throughout the driver,
move it to the private data. Also, in preparation for core clock,
rename it to clk_io.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Mike Looijmans [Tue, 28 Oct 2014 07:53:21 +0000 (08:53 +0100)]
mmc: sdhci-of-arasan: Omit superfluous error messages
sdhci_add_host and sdhci_platfm_init already report failure,
so don't emit error messages when a failure occurs. This prevents
occurences of "deferred" messages when required power supplies
are not ready for operation yet.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Fri, 17 Oct 2014 10:00:56 +0000 (12:00 +0200)]
mmc: core: Convert to use kzalloc() for CXD register buffers
While allocating buffers for CXD data, let's use kzalloc() to make sure
those are zeroed.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Fri, 17 Oct 2014 09:58:24 +0000 (11:58 +0200)]
mmc: core: Don't handle buffers on stack while fetching CXD registers
Due to previous patches, all callers of mmc_send_cxd_data() now
allocates their buffers from the heap. This enables us to simplify
mmc_send_cxd_data() by removing the support of handling buffers, which
are allocated from the stack.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Fri, 17 Oct 2014 09:54:22 +0000 (11:54 +0200)]
mmc: core: Remove the redundant mmc_send_ext_csd() API
Previous patches has replaced the calls to mmc_send_ext_csd() into
mmc_get_ext_csd(), thus mmc_send_ext_csd() has become redundant. Let's
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Fri, 17 Oct 2014 09:48:23 +0000 (11:48 +0200)]
mmc: core: Use mmc_get_ext_csd() instead of mmc_send_ext_csd()
By using mmc_get_ext_csd() in favor of mmc_send_ext_csd, we decrease
code duplication.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Fri, 17 Oct 2014 09:39:05 +0000 (11:39 +0200)]
mmc: block: Use mmc_get_ext_csd() instead of mmc_send_ext_csd()
By using mmc_get_ext_csd() in favor of mmc_send_ext_csd, we decrease
code duplication.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Fri, 17 Oct 2014 09:32:32 +0000 (11:32 +0200)]
mmc: core: Export mmc_get_ext_csd()
Callers of mmc_send_ext_csd() will be able to decrease code duplication
by using mmc_get_ext_csd() instead. Let's make it available.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Thu, 16 Oct 2014 15:00:39 +0000 (17:00 +0200)]
mmc: core: Don't panic when fetching EXT_CSD
Instead of doing BUG_ON(), return an error code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 20 Oct 2014 12:08:16 +0000 (14:08 +0200)]
mmc: core: Let's callers of from mmc_get_ext_csd() do error handling
The callers of mmc_get_ext_csd() need the flexibility to handle errors
themselves, because they behave differently.
Let's clean up mmc_get_ext_csd() with its friends and adopt the error
handling as stated above.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 20 Oct 2014 11:37:24 +0000 (13:37 +0200)]
mmc: core: Fetch and decode EXT_CSD from mmc_read_ext_csd()
As a step in cleaning up code around reading/decoding EXT_CSD, convert
the current mmc_read_ext_csd(), to handle both fetching the EXT_CSD
and decoding its data.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 20 Oct 2014 09:33:53 +0000 (11:33 +0200)]
mmc: core: Add helper function for EXT_CSD support
The helper function mmc_can_ext_csd() will return a positive value if
the card supports the EXT_CSD register. Start using it at relavant
places in the mmc core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Tue, 21 Oct 2014 15:16:14 +0000 (17:16 +0200)]
mmc: core: Remove unnecessary 'out of memory' message
Rely on the prints handled internally by kmalloc().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 20 Oct 2014 09:49:21 +0000 (11:49 +0200)]
mmc: core: Remove redundant check of max_dtr while selecting timings
If the MMC spec version is < CSD_SPEC_VER_4, there aren't support for
the EXT_CSD register. Since max_dtr is fetched from there, it will
default to zero, which thus isn't needed to verify.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 20 Oct 2014 09:18:41 +0000 (11:18 +0200)]
mmc: core: Remove redundant check while selecting powerclass
The validation of the buswidth and the MMC spec version in
__mmc_select_powerclass() is redundant, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Fri, 17 Oct 2014 09:16:57 +0000 (11:16 +0200)]
mmc: core: Remove duplicated definition of mmc_send_ext_csd()
mmc_send_ext_csd() is an exported function used by both the mmc core
and the mmc block layer. Let's remove the local duplicated definition
in the mmc core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Thu, 16 Oct 2014 14:18:51 +0000 (16:18 +0200)]
mmc: core: Remove mmc_free_ext_csd()
Let callers of mmc_free_ext_csd() do kfree() directly instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Doug Anderson [Tue, 14 Oct 2014 16:33:09 +0000 (09:33 -0700)]
mmc: dw_mmc: Remove old card detect infrastructure
The dw_mmc driver had a bunch of code that ran whenever a card was
ejected and inserted. However, this code was old and crufty and
should be removed. Some evidence that it's really not needed:
1. Is is supposed to be legal to use 'cd-gpio' on dw_mmc instead of
using the built-in card detect mechanism. The 'cd-gpio' code
doesn't run any of the crufty old code but yet still works.
2. While looking at this, I realized that my old change (
369ac86 mmc:
dw_mmc: don't queue up a card detect at slot startup) actually
castrated the old code a little bit already and nobody noticed.
Specifically "last_detect_state" was left as 0 at bootup. That
means that on the first card removal none of the crufty code ran.
3. I can run "while true; do dd if=/dev/mmcblk1 of=/dev/null; done"
while ejecting and inserting an SD Card and the world doesn't
explode.
If some of the crufty old code is actually needed, we should justify
it and also put it in some place where it will be run even with
"cd-gpio".
Note that in my case I'm using the "cd-gpio" mechanism but for various
reasons the hardware triggers a dw_mmc "card detect" at bootup. That
was actually causing a real bug. The card detect workqueue was
running while the system was trying to enumerate the card. The
"present != slot->last_detect_state" triggered and we were doing all
kinds of crazy stuff and messing up enumeration. The new mechanism of
just asking the core to check the card is much safer and then the
bogus interrupt doesn't hurt.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: alim.akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dan Carpenter [Thu, 23 Oct 2014 11:37:00 +0000 (14:37 +0300)]
mmc: core: silence a shift wrapping warning
Presumably ->slotno is normally fairly small and the shift doesn't wrap
but static checkers will complain about it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Mike Looijmans [Thu, 23 Oct 2014 11:31:00 +0000 (13:31 +0200)]
mmc: sdhci-of-arasan: Use signed formatting in error messages
"ret" is a signed int, so use "%d" in format strings instead of "%u".
This prevents cryptic codes in error messages like this:
sdhci-arasan
e0101000.sdhci: platform register failed (
4294966779)
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Alexandre Belloni [Fri, 17 Oct 2014 08:26:38 +0000 (10:26 +0200)]
avr32: remove mach/atmel-mci.h
Use the generic platform_data header file instead of mach/atmel-mci.h
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Alexandre Belloni [Fri, 17 Oct 2014 08:26:37 +0000 (10:26 +0200)]
ARM: at91: remove mach/atmel-mci.h
Use the generic platform_data header file instead of mach/atmel-mci.h
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Alexandre Belloni [Fri, 17 Oct 2014 08:26:36 +0000 (10:26 +0200)]
mmc: atmel-mci: move mach header to platform_data
Move the mach header that can come either from arm/mach-at91 or avr32 to
platform_data to be able to switch the AT91 platforms to multiplatform.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Ulf: Fixed compile error]
Gwendal Grignou [Thu, 16 Oct 2014 18:27:16 +0000 (11:27 -0700)]
mmc: core: Report firmware version for eMMC 5.0 devices.
For eMMC 5.0 compliant device, firmware version is stored in ext_csd.
Report firmware as a 64bit hexa decimal. Vendor can use hexa or ascii
string to report firmware version.
Also add FFU related EXT_CSD register and note if the device is FFU capable.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Doug Anderson [Tue, 14 Oct 2014 16:39:12 +0000 (09:39 -0700)]
mmc: dw_mmc: rockchip: Don't recalc the clock when it goes off
The "set_ios" function is called with a clock of 0 when the clock is
turning off. There's no reason to go through all the extra Rockchip
logic (whose goal is to make sure DIV is 0 or 1) in that case. The
Rockchip logic happened to work because the CCF will pick the lowest
possible rate when you ask it for a clock of 0, but it's silly to go
through all the remuxing and adjusting for no reason.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Doug Anderson [Sat, 11 Oct 2014 04:16:16 +0000 (21:16 -0700)]
mmc: dw_mmc: Change signal voltage error to dev_dbg()
In (
28f92b5 mmc: core: Try other signal levels during power up) we can
see that there are times when it's valid to try several signal
voltages. Don't print an ugly error in the logs when that happens.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sonny Rao [Thu, 16 Oct 2014 16:58:05 +0000 (09:58 -0700)]
mmc: dw_mmc: Reset DMA before enabling IDMAC
We've already got a reset of DMA after it's done. Add one before we
start DMA too. This fixes a data corruption on Rockchip SoCs which
will get bad data when doing a DMA transfer after doing a PIO transfer.
We tested this on an Exynos 5800 with HS200 and didn't notice any
difference in sequential read throughput.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 6 Oct 2014 12:39:03 +0000 (14:39 +0200)]
mmc: core: Remove unused mmc_list_to_card() macro
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 6 Oct 2014 12:34:09 +0000 (14:34 +0200)]
mmc: block: Use dev_set|get_drvdata()
In most of the cases mmc_get|set_drvdata() didn't simplify code, which
should be the primary reason for such macros.
Let's remove them and convert to the common device_driver macros,
dev_set|get_drvdata() instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 6 Oct 2014 12:08:09 +0000 (14:08 +0200)]
mmc: msm_sdcc: Use platform_set|get_drvdata
The msm_sdcc host shall not use mmc core specific macros to handle its
driver data. Instead, convert to use the platform device driver macros.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 6 Oct 2014 11:51:40 +0000 (13:51 +0200)]
mmc: core: Convert mmc_driver to device_driver
The struct mmc_driver adds an extra layer on top of the struct
device_driver. That would be fine, if there were a good reason, but
that's not the case.
Let's simplify code by converting to the common struct device_driver
instead and thus also removing superfluous overhead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 6 Oct 2014 09:29:42 +0000 (11:29 +0200)]
mmc: core: Convert the mmc_driver to use the modern PM ops
Instead of having specific mmc system PM callbacks for the mmc driver,
let's convert to use the common ones.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 6 Oct 2014 09:00:15 +0000 (11:00 +0200)]
mmc: core: Don't export the to_sdio_driver macro
The macro is only used by the mmc core, so let's move it in there.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 6 Oct 2014 08:28:35 +0000 (10:28 +0200)]
mmc: core: Remove superfluous ifdefs for SDIO bus' PM callbacks
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sebastian Hesselbarth [Tue, 21 Oct 2014 09:22:37 +0000 (11:22 +0200)]
mmc: sdhci-pxav3: Remove checks for mandatory host clock
NULL-checking a struct clk it not only wrong but also not required as
for PXAv3 driver the corresponding clock is mandatory. Remove the
checks from sdhci_pxav3_runtime_{suspend,resume}.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sebastian Hesselbarth [Tue, 21 Oct 2014 09:22:36 +0000 (11:22 +0200)]
mmc: sdhci-pxav3: Remove unused clk_enable from sdhci_pxa
clk_enable from struct sdhci_pxa is unused, remove it from the private
driver data.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sebastian Hesselbarth [Tue, 21 Oct 2014 09:22:35 +0000 (11:22 +0200)]
mmc: sdhci-pxav3: Move private driver data to driver source
struct sdhci_pxa is only used in sdhci_pxa driver itself, so move it
there.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sebastian Hesselbarth [Tue, 21 Oct 2014 09:22:34 +0000 (11:22 +0200)]
mmc: sdhci-pxav3: Respect MMC_DDR52 timing on uhs signaling
commit
bb8175a8aa42d731a840cd474e348ac3367eb5a0
("mmc: sdhci: clarify DDR timing mode between SD-UHS and eMMC")
added MMC_DDR52 as eMMC's DDR mode to be distinguished from SD-UHS.
While the differentation may be useful, pxav3 SDHCI controller lacks
a corresponding check in its custom .set_uhs_signaling callback for
MMC_DDR52. This patch adds a new switch case for MMC_TIMING_MMC_DDR52
to MMC_TIMING_UHS_DDR50 case.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sebastian Hesselbarth [Tue, 21 Oct 2014 09:22:33 +0000 (11:22 +0200)]
mmc: sdhci-pxav2: Drop unused struct sdhci_pxa
struct sdhci_pxa is private data of PXA SDHCI driver, but not used in
sdhci-pxav2 at all. Drop unused references to struct sdhci_pxa.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tomeu Vizoso [Fri, 3 Oct 2014 15:53:18 +0000 (17:53 +0200)]
mmc: sunxi: Remove unused includes of linux/clk-private.h
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Srinivas Kandagatla [Wed, 8 Oct 2014 11:25:17 +0000 (12:25 +0100)]
mmc: mmci: fix mmci_post_request
If the post request is cancelling the channel and descriptor and which are
equal to host->dma_current and host->dma_desc_current respectively, then it
makes sense to reset these pointers to NULL, so that the driver does not
reference it.
Also the host_cookie can be reset to 0 in cases of error, so that the
core could reissue the same mmc_request.
This patch was tested with 'mmc: core: fix prepared requests while doing
bkops' to fix the below issue.
mmci-pl18x
12400000.sdcc: error during DMA transfer!
Unable to handle kernel paging request at virtual address
40000000
pgd =
c0204000
[
40000000] *pgd=
00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in: ipv6 ath6kl_sdio ath6kl_core
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 3.17.0-rc7-linaro-multi-v7 #1
task:
c0c9d7e0 ti:
c0c92000 task.ti:
c0c92000
PC is at v7_dma_inv_range+0x34/0x4c
LR is at __dma_page_dev_to_cpu+0x80/0x100
pc : [<
c021efc0>] lr : [<
c021af18>] psr:
400f0193
sp :
c0c93e20 ip :
c0c9a478 fp :
c08ea538
r10:
c0c9f548 r9 :
00000002 r8 :
e97d9000
r7 :
00000200 r6 :
c0c9d504 r5 :
c0db0880 r4 :
00000000
r3 :
0000003f r2 :
00000040 r1 :
40000200 r0 :
40000000
Flags: nZcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control:
10c5787d Table:
a9ef406a DAC:
00000015
Process swapper/0 (pid: 0, stack limit = 0xc0c92250)
Stack: (0xc0c93e20 to 0xc0c94000)
3e20:
c021f058 e9a17178 e9a171bc e99dfd6c 00000001 00000001 e995de10 00000002
3e40:
00000000 c021b574 00000000 c04bc4a4 00000000 e9b49ac0 c0ce6e6c e99dfda4
3e60:
00000088 e9810780 c0d8291c c072ea58 00000000 c072d3fc 00000000 c072f534
3e80:
00000000 e9b49ac0 00000100 c0c9a444 00000088 c072f6b4 c072f5d4 e9d40080
3ea0:
e98107dc 00000000 00000000 c0280a60 00000000 7d55bf61 e9810780 e98107dc
3ec0:
00000000 f0002000 c0d460e8 c0d460e8 c0c92000 c0280b60 e9810780 c0ce7190
3ee0:
00000000 c028369c c02835f4 00000088 00000088 c0280278 c0c8ec70 c020f080
3f00:
f000200c c0c9a958 c0c93f28 c02088e4 c04bd630 c04bd5bc 200f0013 ffffffff
3f20:
c0c93f5c c0212800 00000001 a987c000 c0c93f3c c04bd574 00000000 0000015b
3f40:
ea7a0e40 00000000 c0d460e8 c0d460e8 c0c92000 c08ea538 29b12000 c0c93f70
3f60:
c04bd630 c04bd5bc 200f0013 ffffffff c04bd574 c071bd24 7d50c9b4 c0719a44
3f80:
7d50c9b4 0000015b c0c9a498 c0c92028 c0c9a498 c0c9a4fc ea7a0e40 c0c8ee38
3fa0:
c0d460e8 c0276198 00000000 c0d8291a 00000000 c0c9a400 00000000 c0be0bc4
3fc0:
ffffffff ffffffff c0be05f8 00000000 00000000 c0c533d8 c0d82ed4 c0c9a47c
3fe0:
c0c533d4 c0c9e870 8020406a 511f06f0 00000000 80208074 00000000 00000000
[<
c021efc0>] (v7_dma_inv_range) from [<
c021af18>] (__dma_page_dev_to_cpu+0x80/0x100)
[<
c021af18>] (__dma_page_dev_to_cpu) from [<
c021b574>] (arm_dma_unmap_sg+0x5c/0x84)
[<
c021b574>] (arm_dma_unmap_sg) from [<
c072ea58>] (mmci_dma_unmap.isra.16+0x60/0x74)
[<
c072ea58>] (mmci_dma_unmap.isra.16) from [<
c072f534>] (mmci_data_irq+0x1fc/0x29c)
[<
c072f534>] (mmci_data_irq) from [<
c072f6b4>] (mmci_irq+0xe0/0x114)
[<
c072f6b4>] (mmci_irq) from [<
c0280a60>] (handle_irq_event_percpu+0x78/0x134)
[<
c0280a60>] (handle_irq_event_percpu) from [<
c0280b60>] (handle_irq_event+0x44/0x64)
[<
c0280b60>] (handle_irq_event) from [<
c028369c>] (handle_fasteoi_irq+0xa8/0x1a8)
[<
c028369c>] (handle_fasteoi_irq) from [<
c0280278>] (generic_handle_irq+0x2c/0x3c)
[<
c0280278>] (generic_handle_irq) from [<
c020f080>] (handle_IRQ+0x40/0x90)
[<
c020f080>] (handle_IRQ) from [<
c02088e4>] (gic_handle_irq+0x38/0x68)
[<
c02088e4>] (gic_handle_irq) from [<
c0212800>] (__irq_svc+0x40/0x54)
Exception stack(0xc0c93f28 to 0xc0c93f70)
3f20:
00000001 a987c000 c0c93f3c c04bd574 00000000 0000015b
3f40:
ea7a0e40 00000000 c0d460e8 c0d460e8 c0c92000 c08ea538 29b12000 c0c93f70
3f60:
c04bd630 c04bd5bc 200f0013 ffffffff
[<
c0212800>] (__irq_svc) from [<
c04bd5bc>] (msm_cpu_pm_enter_sleep+0x48/0x4c)
[<
c04bd5bc>] (msm_cpu_pm_enter_sleep) from [<
c071bd24>] (qcom_lpm_enter_spc+0x20/0x2c)
[<
c071bd24>] (qcom_lpm_enter_spc) from [<
c0719a44>] (cpuidle_enter_state+0x44/0xf0)
[<
c0719a44>] (cpuidle_enter_state) from [<
c0276198>] (cpu_startup_entry+0x1f4/0x238)
[<
c0276198>] (cpu_startup_entry) from [<
c0be0bc4>] (start_kernel+0x384/0x390)
Code:
1e070f3e e1110003 e1c11003 1e071f3e (
ee070f36)
---[ end trace
cf6cb3f6432c9834 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Srinivas Kandagatla [Wed, 8 Oct 2014 11:24:24 +0000 (12:24 +0100)]
mmc: core: fix prepared requests while doing bkops
While starting the bkops the previously prepared request should be canceled
and restarted after the bkops. As the prepared resource might already
setup the dma channels and ready to be started. Now with the arrival of bkops
request this prepared request can be serviced ONLY after the bkops. So
holding on to the prepared request in the host driver is confusing at
this point in time, so it makes sense to cleanup such dangling requests and
reissue this request once bkops is done.
Canceling the prepared request would give opportunity to the host drivers
to perform cleanup on the prepared request.
Without this patch host drivers like mmci gets confused when a blocking
request like send_ext_csd(CMD8) is issued while there is already a prepared
request. With the help of this patch, the driver can better manage such
blocking requests and cleanup the prepared requests which are not started yet.
Without this patch I hit below crash on Qualcomm APQ8064 based IFC6410 board
with mmci host driver.
mmci-pl18x
12400000.sdcc: error during DMA transfer!
Unable to handle kernel paging request at virtual address
40000000
pgd =
c0204000
[
40000000] *pgd=
00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in: ipv6 ath6kl_sdio ath6kl_core
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 3.17.0-rc7-linaro-multi-v7 #1
task:
c0c9d7e0 ti:
c0c92000 task.ti:
c0c92000
PC is at v7_dma_inv_range+0x34/0x4c
LR is at __dma_page_dev_to_cpu+0x80/0x100
pc : [<
c021efc0>] lr : [<
c021af18>] psr:
400f0193
sp :
c0c93e20 ip :
c0c9a478 fp :
c08ea538
r10:
c0c9f548 r9 :
00000002 r8 :
e97d9000
r7 :
00000200 r6 :
c0c9d504 r5 :
c0db0880 r4 :
00000000
r3 :
0000003f r2 :
00000040 r1 :
40000200 r0 :
40000000
Flags: nZcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control:
10c5787d Table:
a9ef406a DAC:
00000015
Process swapper/0 (pid: 0, stack limit = 0xc0c92250)
Stack: (0xc0c93e20 to 0xc0c94000)
3e20:
c021f058 e9a17178 e9a171bc e99dfd6c 00000001 00000001 e995de10 00000002
3e40:
00000000 c021b574 00000000 c04bc4a4 00000000 e9b49ac0 c0ce6e6c e99dfda4
3e60:
00000088 e9810780 c0d8291c c072ea58 00000000 c072d3fc 00000000 c072f534
3e80:
00000000 e9b49ac0 00000100 c0c9a444 00000088 c072f6b4 c072f5d4 e9d40080
3ea0:
e98107dc 00000000 00000000 c0280a60 00000000 7d55bf61 e9810780 e98107dc
3ec0:
00000000 f0002000 c0d460e8 c0d460e8 c0c92000 c0280b60 e9810780 c0ce7190
3ee0:
00000000 c028369c c02835f4 00000088 00000088 c0280278 c0c8ec70 c020f080
3f00:
f000200c c0c9a958 c0c93f28 c02088e4 c04bd630 c04bd5bc 200f0013 ffffffff
3f20:
c0c93f5c c0212800 00000001 a987c000 c0c93f3c c04bd574 00000000 0000015b
3f40:
ea7a0e40 00000000 c0d460e8 c0d460e8 c0c92000 c08ea538 29b12000 c0c93f70
3f60:
c04bd630 c04bd5bc 200f0013 ffffffff c04bd574 c071bd24 7d50c9b4 c0719a44
3f80:
7d50c9b4 0000015b c0c9a498 c0c92028 c0c9a498 c0c9a4fc ea7a0e40 c0c8ee38
3fa0:
c0d460e8 c0276198 00000000 c0d8291a 00000000 c0c9a400 00000000 c0be0bc4
3fc0:
ffffffff ffffffff c0be05f8 00000000 00000000 c0c533d8 c0d82ed4 c0c9a47c
3fe0:
c0c533d4 c0c9e870 8020406a 511f06f0 00000000 80208074 00000000 00000000
[<
c021efc0>] (v7_dma_inv_range) from [<
c021af18>] (__dma_page_dev_to_cpu+0x80/0x100)
[<
c021af18>] (__dma_page_dev_to_cpu) from [<
c021b574>] (arm_dma_unmap_sg+0x5c/0x84)
[<
c021b574>] (arm_dma_unmap_sg) from [<
c072ea58>] (mmci_dma_unmap.isra.16+0x60/0x74)
[<
c072ea58>] (mmci_dma_unmap.isra.16) from [<
c072f534>] (mmci_data_irq+0x1fc/0x29c)
[<
c072f534>] (mmci_data_irq) from [<
c072f6b4>] (mmci_irq+0xe0/0x114)
[<
c072f6b4>] (mmci_irq) from [<
c0280a60>] (handle_irq_event_percpu+0x78/0x134)
[<
c0280a60>] (handle_irq_event_percpu) from [<
c0280b60>] (handle_irq_event+0x44/0x64)
[<
c0280b60>] (handle_irq_event) from [<
c028369c>] (handle_fasteoi_irq+0xa8/0x1a8)
[<
c028369c>] (handle_fasteoi_irq) from [<
c0280278>] (generic_handle_irq+0x2c/0x3c)
[<
c0280278>] (generic_handle_irq) from [<
c020f080>] (handle_IRQ+0x40/0x90)
[<
c020f080>] (handle_IRQ) from [<
c02088e4>] (gic_handle_irq+0x38/0x68)
[<
c02088e4>] (gic_handle_irq) from [<
c0212800>] (__irq_svc+0x40/0x54)
Exception stack(0xc0c93f28 to 0xc0c93f70)
3f20:
00000001 a987c000 c0c93f3c c04bd574 00000000 0000015b
3f40:
ea7a0e40 00000000 c0d460e8 c0d460e8 c0c92000 c08ea538 29b12000 c0c93f70
3f60:
c04bd630 c04bd5bc 200f0013 ffffffff
[<
c0212800>] (__irq_svc) from [<
c04bd5bc>] (msm_cpu_pm_enter_sleep+0x48/0x4c)
[<
c04bd5bc>] (msm_cpu_pm_enter_sleep) from [<
c071bd24>] (qcom_lpm_enter_spc+0x20/0x2c)
[<
c071bd24>] (qcom_lpm_enter_spc) from [<
c0719a44>] (cpuidle_enter_state+0x44/0xf0)
[<
c0719a44>] (cpuidle_enter_state) from [<
c0276198>] (cpu_startup_entry+0x1f4/0x238)
[<
c0276198>] (cpu_startup_entry) from [<
c0be0bc4>] (start_kernel+0x384/0x390)
Code:
1e070f3e e1110003 e1c11003 1e071f3e (
ee070f36)
---[ end trace
cf6cb3f6432c9834 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Reported-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andrew Gabbasov [Wed, 1 Oct 2014 12:14:11 +0000 (07:14 -0500)]
mmc: core: Fix error paths and messages in mmc_init_card
In mmc_init_card function some of the branches in error handling paths
go to "err" label, which skips removing of newly allocated card structure,
that will actually not be used. Fix that by using proper "free_card" label.
Also, some messages in these branches are reported as warnings,
although the operation processing is not continued. Change these
messages to error level.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andrew Gabbasov [Wed, 1 Oct 2014 12:14:10 +0000 (07:14 -0500)]
mmc: core: Add debug message for SET_BLOCK_COUNT result
The debug messages with commands execution results, that are printed
after processing the request, do not include results of sbc (set block count)
part of request. Add the debug message for that part too.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andrew Gabbasov [Wed, 1 Oct 2014 12:14:09 +0000 (07:14 -0500)]
mmc: core: Initialize SET_BLOCK_COUNT request fields
Some request fields are initialized just before request processing
for sanity purposes. This is done for command, data, and stop parts
of the request, but not for sbc (set block count) part. Add such
initialization for that part too.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andrew Gabbasov [Wed, 1 Oct 2014 12:14:08 +0000 (07:14 -0500)]
mmc: sdhci: fix error conditions for controller reset
Add the case of SET_BLOCK_COUNT command error to the error conditions
check for making a controller reset at request handling finish.
Otherwise, if the SET_BLOCK_COUNT command failed, e.g. with a timeout,
the controller state was not reset, and the next command failed too.
In the case of data error the controller reset is already done in
finish_data() function before sending stop command (if present),
so the finish tasklet should make a reset after data error only
if no stop command existed in the request.
Also, fix the indentation of this condition check to make it more logical.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andrew Gabbasov [Wed, 1 Oct 2014 12:14:07 +0000 (07:14 -0500)]
mmc: sdhci: Balance vmmc regulator_disable()
As a follow-up of commit
"mmc: sdhci: Balance vmmc regulator_enable(), and always enable vqmmc"
vmmc regulator disable is also not needed in sdhci_remove_host.
The regulator is completely controlled by mmc_power_up and mmc_power_off
functions and is already disabled by the time of removing the host.
Extra regulator_disable call in sdhci_remove_host is unbalanced and
causes a warning reported by regulator core, so should be removed.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dirk Behme [Wed, 1 Oct 2014 09:25:32 +0000 (04:25 -0500)]
mmc: sdhci-esdhc-imx: don't exit in case of no pinctrl states
The commit
ad93220de7da ("mmc: sdhci-esdhc-imx: change pinctrl state
according to uhs mode") exits the probe in case there are no valid
pinctrl states found.
As there are configurations doing the pin mux properly in the boot
loader, don't exit. Just warn, but go on in case if there are no
pinctrl states in the device tree.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Matteo Facchinetti [Wed, 8 Oct 2014 14:24:33 +0000 (16:24 +0200)]
mmc: mxcmmc: fix the default value for available voltages into mxcmci_probe
If available voltages are not given, mmc_regulator_get_supply() function
returns 0 and mxcmmc driver doesn't set a value for ocr_avail mask.
In accordance with the comment in platform_data/mmc-mxcmmc.h,
fix it, assuming MMC_VDD_32_33 | MMC_VDD_33_34 as default value.
Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Matteo Facchinetti [Tue, 30 Sep 2014 14:59:37 +0000 (16:59 +0200)]
mmc: mxcmmc: fix race condition when dma finish a data transfer
During a read of data block using dma, driver might have two ways to finish to read
and free the resources:
1) checking STATUS_DATA_TRANS_DONE mask, in the mxcmci_irq() routine
(pending to mmc irq)
2) mxmmc driver, registers also a mxcmci_dma_callback() and when transfer is finished,
dma driver calls this callback. (pending to dma irq)
Both ways are concurrent with each other.
Race condition happens when following events occur:
/* (1) mxcmci driver start data transfer */
158.418970: mpc_dma_execute: mpc_dma_execute(): will_access_peripheral start cid=31
158.418976: mpc_dma_issue_pending <-mxcmci_request
158.418983: mxcmci_start_cmd <-mxcmci_request
/* (2) mxcmci driver receive mmc irq */
158.419656: mxcmci_irq <-handle_irq_event_percpu
158.419692: mxcmci_read_response <-mxcmci_irq
/* (3) mxcmci driver checks that transfer is complete and call mxcmci_finish_data() */
158.419726: mxcmci_data_done <-mxcmci_irq
158.419729: mxcmci_finish_data <-mxcmci_data_done
158.419733: dma_direct_unmap_sg <-mxcmci_finish_data
158.419736: mxcmci_swap_buffers.isra.24 <-mxcmci_finish_data
158.419762: mxcmci_read_response <-mxcmci_data_done
/* (4) mxcmci driver (no dma): send stop command */
158.419765: mxcmci_start_cmd <-mxcmci_data_done
/* (5) mxcmci driver (no dma): receive the stop command irq response */
158.419782: mxcmci_irq <-handle_irq_event_percpu
158.419812: mxcmci_read_response <-mxcmci_irq
158.419843: mxcmci_finish_request <-mxcmci_irq
/* (6) dma driver: receive dma irq (finish data transfer) related by request on step 1 */
158.419853: mpc_dma_irq <-handle_irq_event_percpu
158.420001: mpc_dma_irq_process <-mpc_dma_irq
158.420004: mpc_dma_irq_process <-mpc_dma_irq
/* (7) dma driver: start dma tasklet to finish the dma irq handling */
158.420008: mpc_dma_irq_process: mpc_dma_irq_process(): completed ch:31
/* (8) mxcmci driver: start next data transfer using dma */
158.420174: mxcmci_request <-mmc_start_req
158.420182: dma_direct_map_sg <-mxcmci_request
158.420192: mpc_dma_prep_slave_sg <-mxcmci_request
/* (9) dma driver: schedule irq tasklet and execute mxcmci dma driver callback */
158.420250: mpc_dma_tasklet <-tasklet_action
158.420254: mpc_dma_process_completed <-tasklet_action
158.420267: mxcmci_dma_callback <-mpc_dma_process_completed
/* ERROR!!! (10) mxcmci driver callback works on dma data related to the step 1
that is already finished */
158.420271: mxcmci_data_done <-mpc_dma_process_completed
158.420273: mxcmci_finish_data <-mxcmci_data_done
/* ERROR!!! (11) mxcmci driver: clear data that should be used by step 8 and
send an other mmc stop command (already sended on step 4) */
158.420276: dma_direct_unmap_sg <-mxcmci_finish_data
158.420279: mxcmci_swap_buffers.isra.24 <-mxcmci_finish_data
158.420330: mxcmci_read_response <-mxcmci_data_done
158.420333: mxcmci_start_cmd <-mxcmci_data_done
158.420338: dma_run_dependencies <-mpc_dma_process_completed
...
...
...
168.474223: mxcmci_watchdog <-call_timer_fn
168.474236: mxcmci_watchdog: mxcmci_watchdog
168.474397: mpc_dma_device_control <-mxcmci_watchdog
In accordance with the other drivers that using the dma engine,
fix it, leaving *only* to dma driver the complete control to
ending the read operation.
Removing STATUS_READ_OP_DONE event activation, has as effect
to force mxcmci driver to handle the finish data transfer only
by mxcmci dma callback.
Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Peter Guo [Wed, 24 Sep 2014 02:29:04 +0000 (04:29 +0200)]
mmc: sdhci-pci-o2micro: Fix Dell E5440 issue
Fix Dell E5440 when reboot Linux, can't find o2micro sd host chip issue.
Fixes:
01acf6917aed (mmc: sdhci-pci: add support of O2Micro/BayHubTech SD hosts)
Signed-off-by: Peter Guo <peter.guo@bayhubtech.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Baruch Siach [Mon, 22 Sep 2014 07:12:51 +0000 (10:12 +0300)]
mmc: block: add newline to sysfs display of force_ro
Make force_ro consistent with other sysfs entries.
Fixes:
371a689f64b0d ('mmc: MMC boot partitions support')
Cc: Andrei Warkentin <andrey.warkentin@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Linus Torvalds [Sun, 9 Nov 2014 22:55:29 +0000 (14:55 -0800)]
Linux 3.18-rc4
Linus Torvalds [Sun, 9 Nov 2014 22:49:56 +0000 (14:49 -0800)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- enable bpf syscall for compat
- cpu_suspend fix when checking the idle state type
- defconfig update
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: update defconfig for 3.18
arm64: compat: Enable bpf syscall
arm64: psci: fix cpu_suspend to check idle state type for index
Linus Torvalds [Sun, 9 Nov 2014 22:46:36 +0000 (14:46 -0800)]
Merge tag 'armsoc-for-rc4' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another quiet week:
- a fix to silence edma probe error on non-supported platforms from
Arnd
- a fix to enable the PL clock for Parallella, to make mainline
usable with the SDK.
- a somewhat verbose fix for the PLL clock tree on VF610
- enabling of SD/MMC on one of the VF610-based boards (for testing)
- a fix for i.MX where CONFIG_SPI used to be implicitly enabled and
now needs to be added to the defconfig instead
- another maintainer added for bcm2835: Lee Jones"
* tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: zynq: Enable PL clocks for Parallella
dma: edma: move device registration to platform code
ARM: dts: vf610: add SD node to cosmic dts
MAINTAINERS: update bcm2835 entry
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
Linus Torvalds [Sun, 9 Nov 2014 22:33:49 +0000 (14:33 -0800)]
Merge branch 'devicetree/merge' of git://git./linux/kernel/git/glikely/linux
Pull devicetree bugfix from Grant Likely:
"One buffer overflow bug that shouldn't be left around"
* 'devicetree/merge' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of: Fix overflow bug in string property parsing functions
Linus Torvalds [Sun, 9 Nov 2014 22:30:24 +0000 (14:30 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"It's a one liner for an error cleanup path that leads to crashes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix kfree on list_head in btrfs_lookup_csums_range error cleanup
Linus Torvalds [Sun, 9 Nov 2014 22:11:58 +0000 (14:11 -0800)]
Merge tag 'driver-core-3.18-rc4' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are 3 tiny fixes for 3.18-rc4.
One fixes up a long-stading race condition in the driver core for
removing directories in /sys/devices/virtual/ and the other 2 fix up
the wording of a new Kconfig option that was added in 3.18-rc1"
* tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
sysfs: driver core: Fix glue dir race condition by gdp_mutex
Linus Torvalds [Sun, 9 Nov 2014 22:11:07 +0000 (14:11 -0800)]
Merge tag 'staging-3.18-rc4' of git://git./linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some staging/iio fixes for 3.18-rc4.
Nothing major, just a few bugfixes of things that have been reported"
* tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging:iio:
ade7758: Remove "raw" from channel name
staging:iio:
ade7758: Fix check if channels are enabled in prenable
staging:iio:
ade7758: Fix NULL pointer deref when enabling buffer
iio: as3935: allocate correct iio_device size
io: accel: kxcjk-1013: Fix iio_event_spec direction
iio: tsl4531: Fix compiler error when CONFIG_PM_OPS is not defined
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
Linus Torvalds [Sun, 9 Nov 2014 22:07:30 +0000 (14:07 -0800)]
Merge tag 'tty-3.18-rc4' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tiny serial/tty fixes for 3.18-rc4 that resolve some
reported issues"
* tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix pty master poll() after slave closes v2
serial: of-serial: fix uninitialized kmalloc variable
tty/vt: don't set font mappings on vc not supporting this
tty: serial: 8250_mtk: Fix quot calculation
tty: Prevent "read/write wait queue active!" log flooding
tty: Fix high cpu load if tty is unreleaseable
serial: Fix divide-by-zero fault in uart_get_divisor()
Linus Torvalds [Sun, 9 Nov 2014 22:05:53 +0000 (14:05 -0800)]
Merge tag 'usb-3.18-rc4' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.18-rc4.
Just a bunch of little fixes resolving reported issues and new device
ids for existing drivers. Full details are in the shortlog"
* tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
USB: Update default usb-storage delay_use value in kernel-parameters.txt
USB: cdc-acm: add quirk for control-line state requests
phy: omap-usb2: Enable runtime PM of omap-usb2 phy properly
USB: storage: Fix timeout in usb_stor_euscsi_init() and usb_stor_huawei_e220_init()
USB: cdc-acm: only raise DTR on transitions from B0
Revert "storage: Replace magic number with define in usb_stor_euscsi_init()"
usb: core: notify disconnection when core detects disconnect
usb: core: need to call usb_phy_notify_connect after device setup
uas: Add US_FL_NO_ATA_1X quirk for 2 more Seagate models
xhci: no switching back on non-ULT Haswell
USB: quirks: enable device-qualifier quirk for yet another Elan touchscreen
USB: quirks: enable device-qualifier quirk for another Elan touchscreen
MAINTAINERS: Remove duplicate entry for usbip driver
usb: storage: fix build warnings !CONFIG_PM
usb: Remove references to non-existent PLAT_S5P symbol
uas: Add NO_ATA_1X for VIA VL711 devices
xhci: Disable streams on Asmedia 1042 xhci controllers
USB: HWA: fix a warning message
uas: Add US_FL_NO_ATA_1X quirk for 1 more Seagate model
usb-storage: handle a skipped data phase
...
Andreas Färber [Thu, 6 Nov 2014 17:22:10 +0000 (18:22 +0100)]
ARM: dts: zynq: Enable PL clocks for Parallella
The Parallella board comes with a U-Boot bootloader that loads one of
two predefined FPGA bitstreams before booting the kernel. Both define an
AXI interface to the on-board Epiphany processor.
Enable clocks FCLK0..FCLK3 for the Programmable Logic by default.
Otherwise accessing, e.g., the ESYSRESET register freezes the board,
as seen with the Epiphany SDK tools e-reset and e-hw-rev, using /dev/mem.
Cc: <stable@vger.kernel.org> # 3.17.x
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Sat, 8 Nov 2014 17:32:29 +0000 (09:32 -0800)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c bugfixes from Wolfram Sang:
"One bigger cleanup (FSF address removal) and two bugfixes for I2C"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
Linus Torvalds [Sat, 8 Nov 2014 16:47:16 +0000 (08:47 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Two fixlets for the armada SoC interrupt controller"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: armada-370-xp: Fix MPIC interrupt handling
irqchip: armada-370-xp: Fix MSI interrupt handling
Linus Torvalds [Sat, 8 Nov 2014 16:45:20 +0000 (08:45 -0800)]
Merge git://git./linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"For:
- some regression fixes at the Remote Controller core and imon driver
- a build fix for certain randconfigs with ir-hix5hd2
- don't feed power to satellite system at ds3000 driver init
It also contains some fixes for drivers added for Kernel 3.18:
- some fixes at the new ISDB-S driver, and the corresponding bits to
fix some descriptors for this Japanese TV standard at the DVB core
- two warning cleanups for sp2 driver if PM is disabled
- change the default mode for the new vivid driver"
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] sp2: sp2_init() can be static
[media] dvb:tc90522: fix always-false expression
[media] dvb-core: set default properties of ISDB-S
[media] dvb:tc90522: fix stats report
[media] vivid: default to single planar device instances
[media] imon: fix other RC type protocol support
[media] ir-hix5hd2 fix build warning
[media] ds3000: fix LNB supply voltage on Tevii S480 on initialization
[media] rc5-decoder: BZ#85721: Fix RC5-SZ decoding
[media] rc-core: fix protocol_change regression in ir_raw_event_register
Linus Torvalds [Sat, 8 Nov 2014 02:08:02 +0000 (18:08 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This weeks' round of MIPS bug fixes for 3.18:
- wire up the bpf syscall
- fix TLB dump output for R3000 class TLBs
- fix strnlen_user return value if no NUL character was found.
- fix build with binutils 2.24.51+. While there is no binutils 2.25
release yet, toolchains derived from binutils 2.24.51+ are already
in common use.
- the Octeon GPIO code forgot to offline GPIO IRQs.
- fix build error for XLP.
- fix possible BUG assertion with EVA for CMA"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix build with binutils 2.24.51+
MIPS: R3000: Fix debug output for Virtual page number
MIPS: Fix strnlen_user() return value in case of overlong strings.
MIPS: CMA: Do not reserve memory if not required
MIPS: Wire up bpf syscall.
MIPS/Xlp: Remove the dead function destroy_irq() to fix build error
MIPS: Octeon: Make Octeon GPIO IRQ chip CPU hotplug-aware
Linus Torvalds [Fri, 7 Nov 2014 22:08:13 +0000 (14:08 -0800)]
Merge tag 'xfs-for-linus-3.18-rc3' of git://git./linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"This update fixes a warning in the new pagecache_isize_extended() and
updates some related comments, another fix for zero-range
misbehaviour, and an unforntuately large set of fixes for regressions
in the bulkstat code.
The bulkstat fixes are large but necessary. I wouldn't normally push
such a rework for a -rcX update, but right now xfsdump can silently
create incomplete dumps on 3.17 and it's possible that even xfsrestore
won't notice that the dumps were incomplete. Hence we need to get
this update into 3.17-stable kernels ASAP.
In more detail, the refactoring work I committed in 3.17 has exposed a
major hole in our QA coverage. With both xfsdump (the major user of
bulkstat) and xfsrestore silently ignoring missing files in the
dump/restore process, incomplete dumps were going unnoticed if they
were being triggered. Many of the dump/restore filesets were so small
that they didn't evenhave a chance of triggering the loop iteration
bugs we introduced in 3.17, so we didn't exercise the code
sufficiently, either.
We have already taken steps to improve QA coverage in xfstests to
avoid this happening again, and I've done a lot of manual verification
of dump/restore on very large data sets (tens of millions of inodes)
of the past week to verify this patch set results in bulkstat behaving
the same way as it does on 3.16.
Unfortunately, the fixes are not exactly simple - in tracking down the
problem historic API warts were discovered (e.g xfsdump has been
working around a 20 year old bug in the bulkstat API for the past 10
years) and so that complicated the process of diagnosing and fixing
the problems. i.e. we had to fix bugs in the code as well as
discover and re-introduce the userspace visible API bugs that we
unwittingly "fixed" in 3.17 that xfsdump relied on to work correctly.
Summary:
- incorrect warnings about i_mutex locking in pagecache_isize_extended()
and updates comments to match expected locking
- another zero-range bug fix for stray file size updates
- a bunch of fixes for regression in the bulkstat code introduced in
3.17"
* tag 'xfs-for-linus-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
xfs: rework zero range to prevent invalid i_size updates
mm: Remove false WARN_ON from pagecache_isize_extended()
xfs: Check error during inode btree iteration in xfs_bulkstat()
xfs: bulkstat doesn't release AGI buffer on error
Linus Torvalds [Fri, 7 Nov 2014 19:55:47 +0000 (11:55 -0800)]
Merge tag 'regulator-v3.18-rc3' of git://git./linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"More changes than I'd like here, most of them for a single bug
repeated in a bunch of drivers with data not being initialized
correctly, plus a fix to lower the severity of a warning introduced in
the last merge window which can legitimately go off so we don't want
to alarm users excessively"
* tag 'regulator-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mpa01: zero-initialize regulator match table array
regulator: max8660: zero-initialize regulator match table array
regulator: max77802: zero-initialize regulator match table
regulator: max77686: zero-initialize regulator match table
regulator: max1586: zero-initialize regulator match table array
regulator: max77693: Fix use of uninitialized regulator config
regulator: of: Lower the severity of the error with no container
Linus Torvalds [Fri, 7 Nov 2014 19:54:44 +0000 (11:54 -0800)]
Merge tag 'spi-v3.18-rc3' of git://git./linux/kernel/git/broonie/spi
Pull spi bugfixes from Mark Brown:
"A couple of small driver fixes for v3.18, both quite problematic if
you hit a use case that's affected"
* tag 'spi-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: toggle clocks on suspend if not disabled by runtime PM
spi: fsl-dspi: Fix CTAR selection
Johannes Berg [Thu, 30 Oct 2014 09:00:35 +0000 (10:00 +0100)]
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
The ENABLE_DEV_COREDUMP option is misleading as it implies that
it gets the framework enabled, this isn't true it just allows it
to get enabled if a driver needs it.
Rename it to ALLOW_DEV_COREDUMP to better capture its semantics.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aristeu Rozanski [Thu, 16 Oct 2014 15:49:49 +0000 (11:49 -0400)]
tiny: reverse logic for DISABLE_DEV_COREDUMP
It's desirable for allnconfig and tinyconfig targets to result in the
least amount of code possible. DISABLE_DEV_COREDUMP exists as a way to
switch off DEV_COREDUMP regardless if any drivers select
WANT_DEV_COREDUMP.
This patch renames the option to ENABLE_DEV_COREDUMP and setting it to
'n' (as in allnconfig or tinyconfig) will effectively disable device
coredump.
Cc: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laurent Pinchart [Thu, 30 Oct 2014 13:59:37 +0000 (15:59 +0200)]
i2c: core: Dispose OF IRQ mapping at client removal time
Clients instantiated from OF get an IRQ mapping created at device
registration time. Dispose the mapping when the client is removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Wolfram Sang [Mon, 3 Nov 2014 20:16:16 +0000 (21:16 +0100)]
i2c: at91: don't account as iowait
iowait is for blkio [1]. I2C shouldn't use it.
[1] https://lkml.org/lkml/2014/11/3/317
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@kernel.org
Wolfram Sang [Tue, 4 Nov 2014 22:46:27 +0000 (23:46 +0100)]
i2c: remove FSF address
We have a central copy of the GPL for that. Some addresses were already
outdated.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Mark Knibbs [Tue, 4 Nov 2014 13:00:15 +0000 (13:00 +0000)]
USB: Update default usb-storage delay_use value in kernel-parameters.txt
Back in 2010 the default usb-storage delay_use time was reduced from 5 to 1
second (commit
a4a47bc03fe520e95e0c4212bf97c86545fb14f9), but
kernel-parameters.txt wasn't updated to reflect that.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yijing Wang [Fri, 7 Nov 2014 04:05:49 +0000 (12:05 +0800)]
sysfs: driver core: Fix glue dir race condition by gdp_mutex
There is a race condition when removing glue directory.
It can be reproduced in following test:
path 1: Add first child device
device_add()
get_device_parent()
/*find parent from glue_dirs.list*/
list_for_each_entry(k, &dev->class->p->glue_dirs.list, entry)
if (k->parent == parent_kobj) {
kobj = kobject_get(k);
break;
}
....
class_dir_create_and_add()
path2: Remove last child device under glue dir
device_del()
cleanup_device_parent()
cleanup_glue_dir()
kobject_put(glue_dir);
If path2 has been called cleanup_glue_dir(), but not
call kobject_put(glue_dir), the glue dir is still
in parent's kset list. Meanwhile, path1 find the glue
dir from the glue_dirs.list. Path2 may release glue dir
before path1 call kobject_get(). So kernel will report
the warning and bug_on.
This is a "classic" problem we have of a kref in a list
that can be found while the last instance could be removed
at the same time.
This patch reuse gdp_mutex to fix this race condition.
The following calltrace is captured in kernel 3.4, but
the latest kernel still has this bug.
-----------------------------------------------------
<4>[ 3965.441471] WARNING: at ...include/linux/kref.h:41 kobject_get+0x33/0x40()
<4>[ 3965.441474] Hardware name: Romley
<4>[ 3965.441475] Modules linked in: isd_iop(O) isd_xda(O)...
...
<4>[ 3965.441605] Call Trace:
<4>[ 3965.441611] [<
ffffffff8103717a>] warn_slowpath_common+0x7a/0xb0
<4>[ 3965.441615] [<
ffffffff810371c5>] warn_slowpath_null+0x15/0x20
<4>[ 3965.441618] [<
ffffffff81215963>] kobject_get+0x33/0x40
<4>[ 3965.441624] [<
ffffffff812d1e45>] get_device_parent.isra.11+0x135/0x1f0
<4>[ 3965.441627] [<
ffffffff812d22d4>] device_add+0xd4/0x6d0
<4>[ 3965.441631] [<
ffffffff812d0dbc>] ? dev_set_name+0x3c/0x40
....
<2>[ 3965.441912] kernel BUG at ..../fs/sysfs/group.c:65!
<4>[ 3965.441915] invalid opcode: 0000 [#1] SMP
...
<4>[ 3965.686743] [<
ffffffff811a677e>] sysfs_create_group+0xe/0x10
<4>[ 3965.686748] [<
ffffffff810cfb04>] blk_trace_init_sysfs+0x14/0x20
<4>[ 3965.686753] [<
ffffffff811fcabb>] blk_register_queue+0x3b/0x120
<4>[ 3965.686756] [<
ffffffff812030bc>] add_disk+0x1cc/0x490
....
-------------------------------------------------------
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Weng Meiling <wengmeiling.weng@huawei.com>
Cc: <stable@vger.kernel.org> #3.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Manuel Lauss [Fri, 7 Nov 2014 13:13:54 +0000 (14:13 +0100)]
MIPS: Fix build with binutils 2.24.51+
Starting with version 2.24.51.
20140728 MIPS binutils complain loudly
about mixing soft-float and hard-float object files, leading to this
build failure since GCC is invoked with "-msoft-float" on MIPS:
{standard input}: Warning: .gnu_attribute 4,3 requires `softfloat'
LD arch/mips/alchemy/common/built-in.o
mipsel-softfloat-linux-gnu-ld: Warning: arch/mips/alchemy/common/built-in.o
uses -msoft-float (set by arch/mips/alchemy/common/prom.o),
arch/mips/alchemy/common/sleeper.o uses -mhard-float
To fix this, we detect if GAS is new enough to support "-msoft-float" command
option, and if it does, we can let GCC pass it to GAS; but then we also need
to sprinkle the files which make use of floating point registers with the
necessary ".set hardfloat" directives.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: Markos Chandras <Markos.Chandras@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8355/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Dave Chinner [Thu, 6 Nov 2014 21:33:52 +0000 (08:33 +1100)]
xfs: track bulkstat progress by agino
The bulkstat main loop progress is tracked by the "lastino"
variable, which is a full 64 bit inode. However, the loop actually
works on agno/agino pairs, and so there's a significant disconnect
between the rest of the loop and the main cursor. Convert this to
use the agino, and pass the agino into the chunk formatting function
and convert it too.
This gets rid of the inconsistency in the loop processing, and
finally makes it simple for us to skip inodes at any point in the
loop simply by incrementing the agino cursor.
cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 6 Nov 2014 21:31:15 +0000 (08:31 +1100)]
xfs: bulkstat error handling is broken
The error propagation is a horror - xfs_bulkstat() returns
a rval variable which is only set if there are formatter errors. Any
sort of btree walk error or corruption will cause the bulkstat walk
to terminate but will not pass an error back to userspace. Worse
is the fact that formatter errors will also be ignored if any inodes
were correctly formatted into the user buffer.
Hence bulkstat can fail badly yet still report success to userspace.
This causes significant issues with xfsdump not dumping everything
in the filesystem yet reporting success. It's not until a restore
fails that there is any indication that the dump was bad and tha
bulkstat failed. This patch now triggers xfsdump to fail with
bulkstat errors rather than silently missing files in the dump.
This now causes bulkstat to fail when the lastino cookie does not
fall inside an existing inode chunk. The pre-3.17 code tolerated
that error by allowing the code to move to the next inode chunk
as the agino target is guaranteed to fall into the next btree
record.
With the fixes up to this point in the series, xfsdump now passes on
the troublesome filesystem image that exposes all these bugs.
cc: <stable@vger.kernel.org>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Dave Chinner [Thu, 6 Nov 2014 21:31:13 +0000 (08:31 +1100)]
xfs: bulkstat main loop logic is a mess
There are a bunch of variables tha tare more wildy scoped than they
need to be, obfuscated user buffer checks and tortured "next inode"
tracking. This all needs cleaning up to expose the real issues that
need fixing.
cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 6 Nov 2014 21:30:58 +0000 (08:30 +1100)]
xfs: bulkstat chunk-formatter has issues
The loop construct has issues:
- clustidx is completely unused, so remove it.
- the loop tries to be smart by terminating when the
"freecount" tells it that all inodes are free. Just drop
it as in most cases we have to scan all inodes in the
chunk anyway.
- move the "user buffer left" condition check to the only
point where we consume space int eh user buffer.
- move the initialisation of agino out of the loop, leaving
just a simple loop control logic using the clusteridx.
Also, double handling of the user buffer variables leads to problems
tracking the current state - use the cursor variables directly
rather than keeping local copies and then having to update the
cursor before returning.
cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 6 Nov 2014 21:30:30 +0000 (08:30 +1100)]
xfs: bulkstat chunk formatting cursor is broken
The xfs_bulkstat_agichunk formatting cursor takes buffer values from
the main loop and passes them via the structure to the chunk
formatter, and the writes the changed values back into the main loop
local variables. Unfortunately, this complex dance is full of corner
cases that aren't handled correctly.
The biggest problem is that it is double handling the information in
both the main loop and the chunk formatting function, leading to
inconsistent updates and endless loops where progress is not made.
To fix this, push the struct xfs_bulkstat_agichunk outwards to be
the primary holder of user buffer information. this removes the
double handling in the main loop.
Also, pass the last inode processed by the chunk formatter as a
separate parameter as it purely an output variable and is not
related to the user buffer consumption cursor.
Finally, the chunk formatting code is not shared by anyone, so make
it local to xfs_itable.c.
cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 6 Nov 2014 21:29:57 +0000 (08:29 +1100)]
xfs: bulkstat btree walk doesn't terminate
The bulkstat code has several different ways of detecting the end of
an AG when doing a walk. They are not consistently detected, and the
code that checks for the end of AG conditions is not consistently
coded. Hence the are conditions where the walk code can get stuck in
an endless loop making no progress and not triggering any
termination conditions.
Convert all the "tmp/i" status return codes from btree operations
to a common name (stat) and apply end-of-ag detection to these
operations consistently.
cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Jan Kara [Thu, 6 Nov 2014 21:29:25 +0000 (08:29 +1100)]
mm: Fix comment before truncate_setsize()
XFS doesn't always hold i_mutex when calling truncate_setsize() and it
uses a different lock to serialize truncates and writes. So fix the
comment before truncate_setsize().
Reported-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Johan Hovold [Thu, 6 Nov 2014 17:08:33 +0000 (18:08 +0100)]
USB: cdc-acm: add quirk for control-line state requests
Add new quirk for devices that cannot handle control-line state
requests.
Note that we currently send these requests to all devices, regardless of
whether they claim to support it, but that errors are only logged if
support is claimed.
Since commit
0943d8ead30e ("USB: cdc-acm: use tty-port dtr_rts"), which
only changed the timings for these requests slightly, this has been
reported to cause occasional firmware crashes on Simtec Electronics
Entropy Key devices after re-enumeration. Enable the quirk for this
device.
Reported-by: Nix <nix@esperi.org.uk>
Tested-by: Nix <nix@esperi.org.uk>
Cc: stable <stable@vger.kernel.org> # v3.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Thu, 6 Nov 2014 20:24:03 +0000 (12:24 -0800)]
Merge tag 'fixes-for-v3.18-rc4' of git://git./linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.18-rc4
A single fix this for dwc2 this time. Because of
excessive debugging messages, dwc2 would sometimes
fail enumeration. The fix is simple, just converting
a dev_info() into dev_dbg().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Francesco Ruggeri [Fri, 10 Oct 2014 20:09:53 +0000 (13:09 -0700)]
tty: Fix pty master poll() after slave closes v2
Commit
f95499c3030f ("n_tty: Don't wait for buffer work in read() loop")
introduces a race window where a pty master can be signalled that the pty
slave was closed before all the data that the slave wrote is delivered.
Commit
f8747d4a466a ("tty: Fix pty master read() after slave closes") fixed the
problem in case of n_tty_read, but the problem still exists for n_tty_poll.
This can be seen by running 'for ((i=0; i<100;i++));do ./test.py ;done'
where test.py is:
import os, select, pty
(pid, pty_fd) = pty.fork()
if pid == 0:
os.write(1, 'This string should be received by parent')
else:
poller = select.epoll()
poller.register( pty_fd, select.EPOLLIN )
ready = poller.poll( 1 * 1000 )
for fd, events in ready:
if not events & select.EPOLLIN:
print 'missed POLLIN event'
else:
print os.read(fd, 100)
poller.close()
The string from the slave is missed several times.
This patch takes the same approach as the fix for read and special cases
this condition for poll.
Tested on 3.16.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Thu, 6 Nov 2014 20:22:36 +0000 (12:22 -0800)]
Merge tag 'usb-serial-3.18-rc4' of git://git./linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v3.18-rc4
Two fixes of non-atomic allocations in write paths.
Signed-off-by: Johan Hovold <johan@kernel.org>
Linus Torvalds [Thu, 6 Nov 2014 19:33:06 +0000 (11:33 -0800)]
Merge tag 'pci-v3.18-fixes-2' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"This fixes an oops when enabling SR-IOV VF devices. The oops is a
regression I added by configuring all devices during enumeration.
- Don't oops on virtual buses in acpi_pci_get_bridge_handle() (Yinghai Lu)"
* tag 'pci-v3.18-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Don't oops on virtual buses in acpi_pci_get_bridge_handle()
Linus Torvalds [Thu, 6 Nov 2014 19:31:32 +0000 (11:31 -0800)]
Merge tag 'sound-3.18-rc4' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This update contains mostly only fixes for Realtek HD-audio codec
driver in addition to a long-standing sysfs warning bug fix for
USB-audio.
One significant fix for Realtek codecs is the update of EAPD init
codes. This avoids invalid COEF setups for some codec models and may
fix "lost sound" in some cases.
The rest are a bit high volume but only new quirks and ALC668-specific
COEF tables"
* tag 'sound-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Restore default value for ALC668
ALSA: usb-audio: Fix device_del() sysfs warnings at disconnect
ALSA: hda - fix mute led problem for three HP laptops
ALSA: hda/realtek - Update Initial AMP for EAPD control
ALSA: hda - change three SSID quirks to one pin quirk
ALSA: hda - Set GPIO 4 low for a few HP machines
ALSA: hda - Add ultra dock support for Thinkpad X240.
Linus Torvalds [Thu, 6 Nov 2014 19:29:45 +0000 (11:29 -0800)]
Merge tag 'mmc-v3.18-2' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fix from Ulf Hansson:
"Fix card detection regression in the MMC core.
The MMC_CAP2_CD_ACTIVE_HIGH and MMC_CAP2_RO_ACTIVE_HIGH could under
some circumstances be set incorrectly, causing the card detection to
fail"
* tag 'mmc-v3.18-2' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: core: fix card detection regression
Linus Torvalds [Thu, 6 Nov 2014 19:28:14 +0000 (11:28 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull another filesystem fix from Al Viro:
"A fix for embarrassing braino in o2net_send_tcp_msg(). -stable
fodder..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix breakage in o2net_send_tcp_msg()
Isamu Mogi [Thu, 30 Oct 2014 13:07:36 +0000 (22:07 +0900)]
MIPS: R3000: Fix debug output for Virtual page number
Virtual page number of R3000 in entryhi is 20 bit from MSB. But in
dump_tlb(), the bit mask to read it from entryhi is 19 bit (0xffffe000).
The patch fixes that to 0xfffff000.
Signed-off-by: Isamu Mogi <isamu@leafytree.jp>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8290/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>