OSDN Git Service
James Smart [Fri, 2 Jun 2017 04:07:08 +0000 (21:07 -0700)]
scsi: lpfc: Fix vports not logging into target
vports cannot login to target.
For vports, lpfc_nodelist is allocated for targets only on completion of
GFF_ID command. Driver checks if lpfc_nodelist exists for target before
sending GFF_ID. So, GFF_ID and PLOGI are not sent.
As mentioned by the comment in lpfc_prep_node_fc4type() routine, do not
send GFF_ID only if this NPortID is previously identified as FCP
target. Send GFF_ID if it is a newly identified remote port from GID_FT
response.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Fri, 2 Jun 2017 04:07:07 +0000 (21:07 -0700)]
scsi: lpfc: Fix PRLI retry handling when target rejects it.
The nvmet driver was rejecting the initiator's PRLI because its reg_rpi
for the PLOGI was still outstanding. The initiator would resend the
PRLI without delay and get the same answer. The PRLI retries would
exhaust causing the nvme initiator to set the nvmet ndlp to UNMAPPED.
The driver's lpfc_els_retry handler did not have a policy for an LS_RJT
with explanation CMD_IN_PROGRESS for PRLI or NVME_PRLI. This caused the
delay to remain at 0 but retry set 1.
Fix: When the ELS response is LS_RJT, TPC and the command was PRLI or
NVME_PRLI, just set the delay to 1000 mS to get a 1 second delay on the
PRLI retry. This was enough to allow the REG_RPI to complete at the
target.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Fri, 2 Jun 2017 04:07:06 +0000 (21:07 -0700)]
scsi: lpfc: Null pointer dereference when log_verbose is set to 0xffffffff
Kernel panic when log_verbose is set to 0xffffffff
phba->pport is dereferenced before it is initialized
Fix: Do not dereference phba->pport if it is NULL
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Fri, 2 Jun 2017 04:07:05 +0000 (21:07 -0700)]
scsi: lpfc: Fix System panic after loading the driver
System panic with general protection fault during driver load
The driver uses a static array sli4_hba.handler_name to store the irq
handler names. If the io_channel_irqs exceeds the pre-allocated size
(32+1), then the driver will overwrite other fields of sli4_hba.
Fix: Dynamically allocate handler_name.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Fri, 2 Jun 2017 04:07:04 +0000 (21:07 -0700)]
scsi: lpfc: Fix crash on powering off BFS VM with passthrough device
Null pointer dereference when BFS VM is powered off
The driver incorrectly uses sli3_ring on SLI-4 adapters
Use the correct ring structure based on sli_rev
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Tested-by: Raphael Silva <raphasil@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Fri, 2 Jun 2017 04:07:03 +0000 (21:07 -0700)]
scsi: lpfc: Fix return value of board_mode store routine in case of online failure
On hbacmd reset failure, observing wrong string "nline" in kernel log.
On failure, non negative value (1) is returned from sysfs store
routine. It is interpreted as count by kernel and store routine is
called again with the remaining characters as input.
Fix: Return negative error code (-EIO) in case of failure.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Fri, 2 Jun 2017 04:07:02 +0000 (21:07 -0700)]
scsi: lpfc: Fix counters so outstandng NVME IO count is accurate
NVME FC counters don't reflect actual results
Since counters are not atomic, or protected by a lock, the values often
get screwed up.
Make them atomic, like NVMET. Fix up sysfs and debugfs display
accordingly Added Outstanding IOs to stats display
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Fri, 2 Jun 2017 04:07:01 +0000 (21:07 -0700)]
scsi: lpfc: Fix Port going offline after multiple resets.
Observing lpfc port down after issuing hbacmd reset command
Failure in posting SGL buffers. If there is only one SGL buffer and rrq
is valid for its XRI, we are rightly returning NULL but not adding the
buffer back to the SGL list. So, number of buffers become less than
total count and repost fails during reset.
Add SGL buffer back to list before returning NULL.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Fri, 2 Jun 2017 04:07:00 +0000 (21:07 -0700)]
scsi: lpfc: Fix nvmet node ref count handling
When unloading the driver, the NVMET driver would wait the full 30
seconds for its UNMAPPED initiator node to get removed before continuing
with the unload process. NVMEI worked correctly.
For each rport put into UNMAPPED or MAPPED state by NVMET, the driver
puts a reference on the NDLP. The difference is that NVMEI has a
unregister call for its rports and the extra reference is removed in the
unregister process. For NVMET, the driver has to remove the reference
explicitly when dropping out of UNMAPPED or MAPPED because there is no
unregister call.
Add a call to lpfc_nlp_put on the ndlp when NVMET and the old state was
UNMAPPED or MAPPED.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Fri, 2 Jun 2017 04:06:59 +0000 (21:06 -0700)]
scsi: lpfc: Fix Lun Priority level shown as NA
Lun Priority level shown as NA
Remote port is not getting registered for nameserver and fdmi. Due to
which dfc SendCTPassThru cmd is failing.
Made changes to register the remote port for both.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Fri, 2 Jun 2017 04:06:58 +0000 (21:06 -0700)]
scsi: lpfc: Add changes to assist in NVMET debugging
Inconsistent error messages and context state checks
Context state sanity checks were not accurate or inconsistent in the
code paths.
Separated LS context states from FCP.
Added and modified context state sanity checks.
Use context state to determine if a sol or unsol ABORT is needed.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Fri, 2 Jun 2017 04:06:57 +0000 (21:06 -0700)]
scsi: lpfc: Fix nvme port role handling in sysfs and debugfs handlers.
While debugging Devloss and recovery, debugfs and sysfs were found to
not show the NVME port roles consistently.
The port role FC_PORT_ROLE_NVME_DISCOVERY was added with the devloss
bringup and the other issues were just oversight.
Add NVME Target and DISCSRVC to debugfs nodeinfo and sysfs nvme info
handlers. The full port role was added to the NVME data only not the
generic nodelist.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Fri, 2 Jun 2017 04:06:56 +0000 (21:06 -0700)]
scsi: lpfc: Fix transition nvme-i rport handling to nport only.
As the devloss API was implemented in the nvmei driver, an evaluation of
the nvme transport and the lpfc driver showed dual management of the
rports. This creates a bug possibility when the thread count and SAN
size increases.
The nvmei driver code was based on a very early transport and was not
revisited until the devloss API was introduced.
Remove the listhead in the driver's rport data structure and the
listhead in the driver's lport data structure. Remove all rport_list
traversal. Convert the driver to use the nrport (nvme rport) pointer
that is now NULL or nonNULL depending on a devloss action. Convert
debugfs and nvme_info in sysfs to use the fc_nodes list in the vport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Fri, 2 Jun 2017 04:06:55 +0000 (21:06 -0700)]
scsi: lpfc: Add nvme initiator devloss support
Add nvme initiator devloss support
The existing implementation was based on no devloss behavior in the
transport (e.g. immediate teardown) so code didn't properly handle
delayed nvme rport device unregister calls. In addition, the driver was
not correctly cycling the rport port role for each
register-unregister-reregister process.
This patch does the following:
Rework the code to properly handle rport device unregister calls and
potential re-allocation of the remoteport structure if the port comes
back in under dev_loss_tmo.
Correct code that was incorrectly cycling the rport port role for each
register-unregister-reregister process.
Prep the code to enable calling the nvme_fc transport api to dynamically
update dev_loss_tmo when the scsi sysfs interface changes it.
Memset the rpinfo structure in the registration call to enforce "accept
nvme transport defaults" in the registration call. Driver parameters do
influence the dev_loss_tmo transport setting dynamically.
Simplifies the register function: the driver was incorrectly searching
its local rport list to determine resume or new semantics, which is not
valid as the transport already handles this. The rport was resumed if
the rport handed back matches the ndlp->nrport pointer. Otherwise,
devloss fired and the ndlp's nrport is NULL.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christophe JAILLET [Sun, 11 Jun 2017 06:16:04 +0000 (08:16 +0200)]
scsi: qedf: Merge a few quoted strings split across lines
Merge some quoted strings to improve readability and to save some lines
of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christophe JAILLET [Sun, 11 Jun 2017 06:16:03 +0000 (08:16 +0200)]
scsi: qedf: Use 'dma_zalloc_coherent' to reduce code verbosity.
Replace some 'dma_alloc_coherent+memset' by some quivalent
'dma_zalloc_coherent' in order to reduce code verbosity
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christophe JAILLET [Sun, 11 Jun 2017 06:16:02 +0000 (08:16 +0200)]
scsi: qedf: Fix a return value in case of error in 'qedf_alloc_global_queues'
We should return -ENOMEM in case of memory allocation error, as done
elsewhere in this function.
[mkp: fixed typo]
Fixes:
61d8658b4a435 ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Binoy Jayan [Thu, 8 Jun 2017 10:07:31 +0000 (15:37 +0530)]
scsi: esas2r: Replace semaphore fs_api_semaphore with mutex
The semaphore 'fs_api_semaphore' is used as a simple mutex, so it should
be written as one. Semaphores are going away in the future.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Binoy Jayan [Thu, 8 Jun 2017 10:07:30 +0000 (15:37 +0530)]
scsi: esas2r: Replace semaphore fm_api_semaphore with mutex
The semaphore 'fm_api_semaphore' is used as a simple mutex, so it should
be written as one. Semaphores are going away in the future.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Himanshu Madhani [Tue, 6 Jun 2017 20:55:23 +0000 (13:55 -0700)]
scsi: qla2xxx: Fix compile warning
Fixes following 0-day kernel build warnings:
drivers/scsi/qla2xxx/qla_init.c:6407:50: warning: format '%lx' expects
argument of type 'long unsigned int', but argument 5 has type 'unsigned
int' [-Wformat=]
drivers/scsi/qla2xxx/qla_init.c:6709:50: warning: format '%lx'
expects argument of type 'long unsigned int', but argument 5 has
type 'unsigned int' [-Wformat=]
Fixes:
b95b9452aacf ("scsi: qla2xxx: Fix crash due to mismatch mumber of Q-pair creation for Multi queue")
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Mon, 5 Jun 2017 17:29:58 +0000 (18:29 +0100)]
scsi: qla2xxx: remove redundant null check on tgt
An earlier commit
ed7fb808477b846bb2 ("scsi: qla2xxx: Remove redundant
wait when target is stopped.") removed a null check on ha->tgt.tgt_ops
and replaced it with a new check that null checked tgt, thus making the
subsequent null check on tgt totally redundant. Remove it.
Detected by CoverityScan, CID#
1440452 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adrian Hunter [Tue, 6 Jun 2017 11:35:31 +0000 (14:35 +0300)]
scsi: ufshcd-pci: Add Intel CNL support
Add PCI id and variant ops for Intel CNL UFS host controller.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adrian Hunter [Tue, 6 Jun 2017 11:35:30 +0000 (14:35 +0300)]
scsi: ufshcd-pci: Fix PM config
Put PM functions under correct config options and use standard PM macros
to set callbacks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Thu, 18 May 2017 09:35:24 +0000 (10:35 +0100)]
scsi: lpfc: make a couple of functions static
functions lpfc_nvmet_cleanup_io_context and lpfc_nvmet_setup_io_context
can be made static as they do not need to be in global scope.
Cleans up sparse warnings:
"warning: symbol 'lpfc_nvmet_cleanup_io_context' was not declared.
Should it be static?"
"warning: symbol 'lpfc_nvmet_setup_io_context' was not declared.
Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Fri, 2 Jun 2017 21:22:03 +0000 (14:22 -0700)]
scsi: xen-scsifront: Remove code that zeroes driver-private command data
Since the SCSI core zeroes driver-private command data, remove
that code from the xen-scsifront driver.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: xen-devel@lists.xenproject.org
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Fri, 2 Jun 2017 21:22:02 +0000 (14:22 -0700)]
scsi: virtio_scsi: Remove code that zeroes driver-private command data
Since the SCSI core zeroes driver-private command data, remove
that code from the virtio driver.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Fri, 2 Jun 2017 21:22:01 +0000 (14:22 -0700)]
scsi: snic: Remove code that zeroes driver-private command data
Since the SCSI core zeroes driver-private command data, remove that code
from the snic driver.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Narsimhulu Musini <nmusini@cisco.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Sesidhar Baddela <sebaddel@cisco.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Fri, 2 Jun 2017 21:22:00 +0000 (14:22 -0700)]
scsi: Make scsi_mq_prep_fn() call scsi_init_command()
This patch reduces code duplication. There are two functional changes in
this patch:
- It causes scsi_mq_prep_fn() to clear driver-private command data, just
like the already upstream commit
1bad6c4a57ef ("scsi: zero per-cmd
private driver data for each MQ I/O").
- The initialization of .prot_sdb is moved from scsi_mq_prep_fn() into
scsi_init_request().
[mkp: applied by hand]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Fri, 2 Jun 2017 21:21:59 +0000 (14:21 -0700)]
scsi: Introduce scsi_mq_sgl_size()
This patch does not change any functionality but makes the next patch
easier to read.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Fri, 2 Jun 2017 21:21:58 +0000 (14:21 -0700)]
scsi: Only add commands to the device command list if required by the LLD
Just like for the scsi-mq code path, in the single queue SCSI code path
only add commands to the per-device command list if required by the SCSI
LLD. This patch will make it easier to merge the single-queue and
multiqueue command initialization code.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Fri, 2 Jun 2017 21:21:57 +0000 (14:21 -0700)]
scsi: Make __scsi_remove_device go straight from BLOCKED to DEL
If a device is blocked, make __scsi_remove_device() cause it to
transition to the DEL state. This means that all the commands issued in
.shutdown() will error in the mid-layer, thus making the removal proceed
without being stopped.
This patch is a slightly modified version of a patch from James
Bottomley. This patch avoids that the following lockup occurs:
Call Trace:
schedule+0x35/0x80
schedule_timeout+0x237/0x2d0
io_schedule_timeout+0xa6/0x110
wait_for_completion_io+0xa3/0x110
blk_execute_rq+0xdf/0x120
scsi_execute+0xce/0x150 [scsi_mod]
scsi_execute_req_flags+0x8f/0xf0 [scsi_mod]
sd_sync_cache+0xa9/0x190 [sd_mod]
sd_shutdown+0x6a/0x100 [sd_mod]
sd_remove+0x64/0xc0 [sd_mod]
__device_release_driver+0x8d/0x120
device_release_driver+0x1e/0x30
bus_remove_device+0xf9/0x170
device_del+0x127/0x240
__scsi_remove_device+0xc1/0xd0 [scsi_mod]
scsi_forget_host+0x57/0x60 [scsi_mod]
scsi_remove_host+0x72/0x110 [scsi_mod]
srp_remove_work+0x8b/0x200 [ib_srp]
Reported-by: Israel Rukshin <israelr@mellanox.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Israel Rukshin <israelr@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Fri, 2 Jun 2017 21:21:56 +0000 (14:21 -0700)]
scsi: Introduce scsi_start_queue()
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Israel Rukshin <israelr@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Fri, 2 Jun 2017 21:21:55 +0000 (14:21 -0700)]
scsi: Protect SCSI device state changes with a mutex
Serializing SCSI device state changes avoids that two state changes can
occur concurrently, e.g. the state changes in scsi_target_block() and
__scsi_remove_device(). This serialization is essential to make patch
"Make __scsi_remove_device go straight from BLOCKED to DEL" work
reliably.
Enable this mechanism for all scsi_target_*block() callers but not for
the scsi_internal_device_unblock() calls from the mpt3sas driver because
that driver can call scsi_internal_device_unblock() from atomic context.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Fri, 2 Jun 2017 21:21:54 +0000 (14:21 -0700)]
scsi: Create two versions of scsi_internal_device_unblock()
This will make it easier to serialize SCSI device state changes through
a mutex.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Fri, 2 Jun 2017 21:21:53 +0000 (14:21 -0700)]
scsi: Split scsi_internal_device_block()
Instead of passing a "wait" argument to scsi_internal_device_block(),
split this function into a function that waits and a function that
doesn't wait. This will make it easier to serialize SCSI device state
changes through a mutex.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Fri, 2 Jun 2017 21:21:52 +0000 (14:21 -0700)]
scsi: Avoid that scsi_exit_rq() triggers a use-after-free
Dereferencing shost from scsi_exit_rq() is not safe because the SCSI
host may already have been freed when scsi_exit_rq() is called.
Increasing the shost reference count in scsi_init_rq() and dropping that
reference in scsi_exit_rq() is nontrivial since scsi_host_dev_release()
may sleep and since scsi_exit_rq() may be called from interrupt
context. Since scsi_exit_rq() only needs a single bit from shost, copy
that bit into struct scsi_cmnd.
Reported-by: Scott Bauer <scott.bauer@intel.com>
Fixes:
e9c787e65c0c ("scsi: allocate scsi_cmnd structures as part of struct request")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Scott Bauer <scott.bauer@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Jia-Ju Bai [Wed, 31 May 2017 02:56:56 +0000 (10:56 +0800)]
scsi: megaraid: Fix a sleep-in-atomic bug
The driver may sleep under a spin lock, and the function call path is:
mraid_mm_attach_buf (acquire the lock by spin_lock_irqsave)
pci_pool_alloc(GFP_KERNEL) --> may sleep
To fix it, the "GFP_KERNEL" is replaced with "GFP_ATOMIC".
[mkp: fixed whitespace]
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Szymon Mielczarek [Mon, 5 Jun 2017 08:36:54 +0000 (11:36 +0300)]
scsi: ufs: Tidy clocks list head usage
Move the initialization of clocks list head to ufshcd_alloc_host() so
that every driver doesn't have to do it. Remove checks for the list head
being NULL because that is not possible.
Signed-off-by: Szymon Mielczarek <szymonx.mielczarek@intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Michael Schmitz [Mon, 5 Jun 2017 07:37:59 +0000 (19:37 +1200)]
scsi: atari_scsi: Use m68k_realnum_memory for FastRAM test
m68k_num_memory is unsuitable to test for the presence of FastRAM on
CT60 if the kernel is located in FastRAM: in arch/m68k/mm/motorola.c the
ST-RAM chunk is skipped and m68k_num_memory is decremented in this
case. m68k_realnum_memory still contains the actual number of RAM chunks
so use that.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Christian T. Steigies <cts@debian.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Corentin Labbe [Fri, 2 Jun 2017 11:32:25 +0000 (13:32 +0200)]
scsi: qla2xxx: remove writeq/readq function definitions
Instead of rewriting write/readq, use linux/io-64-nonatomic-lo-hi.h
which already have them.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dupuis, Chad [Fri, 2 Jun 2017 19:02:05 +0000 (12:02 -0700)]
scsi: qedf: Check if sense buffer has been allocated during completion
sc_cmd->sense_buffer is not guaranteed to be allocated so we need to
sc_cmd->check
if the pointer is NULL before trying to copy anything into it.
Fixes the crash:
[ 143.793176] [0000:00:00.0]:[qedf_eh_device_reset:626]: LUN RESET Issued...
[ 143.802996] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 143.803063] IP: qedf_parse_fcp_rsp+0xe2/0x290 [qedf]
[ 143.803077] PGD 0
[ 143.803078] P4D 0
[ 143.803103] Oops: 0002 [#1] SMP
[ 143.803115] Modules linked in: msr(E) ebtable_filter(E) ebtables(E) ip6table_filter(E) ip6_tables(E) iptable_filter(E) ip_tables(E) x_tables(E) raw(E) scsi_transport_iscsi(E) br_netfilter(E) bridge(E) iscsi_ibft(E) iscsi_boot_sysfs(E) intel_rapl(E) sb_edac(E) x86_pkg_temp_thermal(E) intel_powerclamp(E) coretemp(E) kvm_intel(E) kvm(E) irqbypass(E) crct10dif_pclmul(E) crc32_pclmul(E) xfs(E) ghash_clmulni_intel(E) pcbc(E) aesni_intel(E) aes_x86_64(E) crypto_simd(E) ipmi_ssif(E) glue_helper(E) iTCO_wdt(E) iTCO_vendor_support(E) lpc_ich(E) ipmi_si(E) pcspkr(E) hpilo(E) ioatdma(E) cryptd(E) ipmi_devintf(E) hpwdt(E) mfd_core(E) shpchp(E) dca(E) thermal(E) pcc_cpufreq(E) ipmi_msghandler(E) acpi_cpufreq(E) af_packet(E) btrfs(E) xor(E) raid6_pq(E) sr_mod(E) cdrom(E) ata_generic(E) sd_mod(E) 8021q(E) garp(E)
[ 143.803302] stp(E) llc(E) mrp(E) bnx2fc(E) cnic(E) uio(E) mgag200(E) ata_piix(E) i2c_algo_bit(E) drm_kms_helper(E) syscopyarea(E) sysfillrect(E) sysimgblt(E) ahci(E) fb_sys_fops(E) bnx2x(E) qedf(E) serio_raw(E) libahci(E) ttm(E) uhci_hcd(E) ehci_pci(E) qed(E) mdio(E) libcrc32c(E) ehci_hcd(E) crc32c_intel(E) drm(E) libata(E) usbcore(E) tg3(E) ptp(E) hpsa(E) pps_core(E) scsi_transport_sas(E) libphy(E) wmi(E) button(E) fcoe(E) libfcoe(E) libfc(E) scsi_transport_fc(E) sg(E) dm_multipath(E) dm_mod(E) scsi_dh_rdac(E) scsi_dh_emc(E) scsi_dh_alua(E) scsi_mod(E) autofs4(E)
[ 143.803438] CPU: 31 PID: 494 Comm: kworker/31:2 Tainted: G E 4.12.0-rc1-69-default+ #1
[ 143.803461] Hardware name: HP ProLiant DL380p Gen8, BIOS P70 08/20/2012
[ 143.803480] Workqueue: qedf_io_wq qedf_fp_io_handler [qedf]
[ 143.803496] task:
ffff8804181a0000 task.stack:
ffffc90003b64000
[ 143.803514] RIP: 0010:qedf_parse_fcp_rsp+0xe2/0x290 [qedf]
[ 143.803529] RSP: 0018:
ffffc90003b67dc8 EFLAGS:
00010246
[ 143.803544] RAX:
0000000000000000 RBX:
ffff880401abdd48 RCX:
000000000000000c
[ 143.803563] RDX:
0000000000000060 RSI:
ffffffffa039c740 RDI:
0000000000000000
[ 143.803581] RBP:
ffffc90003b67df0 R08:
ffffffffa039dba8 R09:
0000000000000000
[ 143.803600] R10:
0000000000000000 R11:
0000000000000018 R12:
0000000000000000
[ 143.803619] R13:
ffff88040ac80bc8 R14:
0000000000000008 R15:
ffff880407c14008
[ 143.803638] FS:
0000000000000000(0000) GS:
ffff88043f7c0000(0000) knlGS:
0000000000000000
[ 143.804360] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 143.805065] CR2:
0000000000000000 CR3:
0000000001c09000 CR4:
00000000000406e0
[ 143.805753] Call Trace:
[ 143.806436] qedf_process_tmf_compl+0x19/0x30 [qedf]
[ 143.807124] qedf_process_cqe+0x265/0x280 [qedf]
[ 143.807800] qedf_fp_io_handler+0x26/0x60 [qedf]
[ 143.808469] process_one_work+0x138/0x370
[ 143.809133] worker_thread+0x4d/0x3b0
[ 143.809797] kthread+0x109/0x140
[ 143.810451] ? rescuer_thread+0x320/0x320
[ 143.811100] ? kthread_park+0x60/0x60
[ 143.811743] ret_from_fork+0x2c/0x40
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 2 Jun 2017 16:12:07 +0000 (09:12 -0700)]
scsi: qla2xxx: Remove extra register read
Remove extra register read in each interrupt processing to improve
performance.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 2 Jun 2017 16:12:06 +0000 (09:12 -0700)]
scsi: qla2xxx: Remove unused irq_cmd_count field.
When driver is unloaded, all sessions are torn down, all commmands are
flushed, chip is reset to ensure there is no knowledge of target mode in
ISP. The irq_cmd_count field was used to make sure all commands are
processed on top of that. The irq_cmd_count is now redundant and not
needed.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 2 Jun 2017 16:12:05 +0000 (09:12 -0700)]
scsi: qla2xxx: Accelerate SCSI BUSY status generation in target mode
Accelerate generation of SCSI busy to let initiators slow down when
target is running low in resources.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 2 Jun 2017 16:12:04 +0000 (09:12 -0700)]
scsi: qla2xxx: Remove redundant wait when target is stopped.
Current code already destroy all target sessions when target Mode is
stopped. Target core would waits for all commands that belong to each
session to purge. The extra wait for interrupts to settle down is not
relevant.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 2 Jun 2017 16:12:03 +0000 (09:12 -0700)]
scsi: qla2xxx: Add ql2xiniexchg parameter
Previously, the ql2xexchoffld module parameter was used to control the
max number of exchanges to be offload onto host memory.
Module parameter ql_dm_tgt_ex_pct was used to control the percentage of
exchanges allocated to the Target side.
With this patch, module parameter ql_dm_tgt_ex_pct is no longer used to
control exchanges for the driver. New module parameter ql2xiniexchg is
added to control exchanges between target mode and initiator mode.
With the updated module parameters, users can control the exact number
of exchanges for either Initiator or Target. The exchange offload
feature will be automatically enabled when the total number of exchanges
exceeds 2048 limit.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 2 Jun 2017 16:12:02 +0000 (09:12 -0700)]
scsi: qla2xxx: Turn on FW option for exchange check
Tell FW to track exchange/cmd state to prevent driver from using stale
exchange or exchange that is not meant for this command.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 2 Jun 2017 16:12:01 +0000 (09:12 -0700)]
scsi: qla2xxx: Cleanup debug message IDs
Assign unique id to all traces and logs for debug purpose.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 2 Jun 2017 16:12:00 +0000 (09:12 -0700)]
scsi: qla2xxx: Fix name server relogin
Name server login is normally handle by FW. In some rare case where one
of the switches is being updated, name server login could get
affected. Trigger relogin to name server when driver detects this
condition.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 2 Jun 2017 16:11:59 +0000 (09:11 -0700)]
scsi: qla2xxx: Convert 32-bit LUN usage to 64-bit
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sawan Chandak [Fri, 2 Jun 2017 16:11:58 +0000 (09:11 -0700)]
scsi: qla2xxx: Use flag PFLG_DISCONNECTED.
There is already flag defined PFLG_DISCONNECTED, which is set
for PCI or register disconnect error condition. There is no need to have
flag PCI_ERR, which has same purpose. Remove use of PCI_ERR flag and use
PFLG_DISCONNECTED flag during error condition.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 2 Jun 2017 16:11:57 +0000 (09:11 -0700)]
scsi: tcm_qla2xxx: Do not allow aborted cmd to advance.
In case of hardware queue full, commands can loop between
TCM stack and tcm_qla2xx shim layers for retry. While command
is waiting for retry, task mgmt can get ahead and abort the
cmmand that encountered queue full condition. Fix this by
dropping the command, if task mgmt has already started the
command free process.
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 2 Jun 2017 16:11:56 +0000 (09:11 -0700)]
scsi: qla2xxx: Fix path recovery
If the port is moved/changed, current code would trigger
a deletion. If the port is already deleted, then do relogin.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Joe Carnuccio [Fri, 2 Jun 2017 16:11:55 +0000 (09:11 -0700)]
scsi: qla2xxx: Retain loop test for fwdump length exceeding buffer length
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 2 Jun 2017 16:11:54 +0000 (09:11 -0700)]
scsi: qla2xxx: Replace usage of spin_lock with spin_lock_irqsave
Convert usage of spin_lock to spin_lock_irqsave because qla2xxx driver
can access all the data structures in an interrupt context.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 2 Jun 2017 16:11:53 +0000 (09:11 -0700)]
scsi: qla2xxx: Allow ABTS, PURX, RIDA on ATIOQ for ISP83XX/27XX
Driver added mechanism to move ABTS/PUREX/RIDA mailbox to
ATIO queue as part of commit id
41dc529a4602ac737020f423f84686a81de38e6d
("qla2xxx: Improve RSCN handling in driver").
This patch adds a check to only allow ABTS/PURX/RIDA
to be moved to ATIO Queue for ISP83XX and ISP27XX.
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Wed, 31 May 2017 13:34:02 +0000 (06:34 -0700)]
scsi: qedf: Update version number to 8.18.22.0.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Wed, 31 May 2017 13:34:01 +0000 (06:34 -0700)]
scsi: qedf: Add change_queue_depth member to scsi_host_template().
Add the change_queue_depth member to our SCSI host template so the queue
depth of devices attached to qedf can be changed dynamically.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Wed, 31 May 2017 13:34:00 +0000 (06:34 -0700)]
scsi: qedf: Change cmd_per_lun in scsi_host_template to 32 to increase performance.
Increase the default number of commands that the driver tells the
SCSI mid-layer it can do to increase the default performance of the
driver.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Wed, 31 May 2017 13:33:59 +0000 (06:33 -0700)]
scsi: qedf: Move some prints to a debug level so they do not print when no debugging is enabled.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Wed, 31 May 2017 13:33:58 +0000 (06:33 -0700)]
scsi: qedf: Fixup unnecessary parantheses around test_bit operations.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Wed, 31 May 2017 13:33:57 +0000 (06:33 -0700)]
scsi: qedf: Add non-offload receive filters.
Drop invalid or unexpected FCoE frames that come into the non-offload path
since the FCoE firmware would not do the filtering for us.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Wed, 31 May 2017 13:33:56 +0000 (06:33 -0700)]
scsi: qedf: Add bus_reset No-op.
We need to add a bus reset no-op as without it some of the LUNs attached to a
vport may go offline when the error handler escalates to host reset due to not
having a bus reset handler in the driver. What happens is we escalate to host
reset which does a soft link down/link up to reset the adapter. However with
multiple vports attached it's been observed that if the vports do log back into
the target within 5 seconds, the SCSI layer offlines the devices most likely
due to a TUR timing out to verify that the device is online. Adding a bus
reset handler will cause the TUR to be sent after the bus reset handler where
the devices will still be online if the bus reset is initiated by sg_reset
(which is the case in the test that was failing). The bus reset will succeed
and not needlessly bring the device offline/online.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Wed, 31 May 2017 13:33:55 +0000 (06:33 -0700)]
scsi: qedf: Use same logic for SCSI host reset and FC lip_reset.
We should be using the same logic to do a soft reset of the FCoE function
whether it is initiated via sg_reset or the fc_host issue_lip attribute.
Refactor the host reset and fcoe reset handlers to use the preferred logic
which is currently contained in qedf_eh_host_reset().
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Wed, 31 May 2017 13:33:54 +0000 (06:33 -0700)]
scsi: qedf: Set qed logging level to QED_LEVEL_NOTICE.
Reduce the logging level we set for qed messages pertaining to this PCI
function so that unnecessary messages are not printed in the kernel
message log.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Wed, 31 May 2017 13:33:53 +0000 (06:33 -0700)]
scsi: qedf: Add fka_period SCSI host attribute to show fip keep alive period.
Expose this information for interested applications.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Wed, 31 May 2017 13:33:52 +0000 (06:33 -0700)]
scsi: qedf: Check that fcport is offloaded before dereferencing pointers in initiate_abts|cleanup.
If an fcport is not offloaded then the members of the qedf_rport struct
are undefined which may cause a system crash.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Wed, 31 May 2017 13:33:51 +0000 (06:33 -0700)]
scsi: qedf: Look at all descriptors when processing a clear virtual link.
If there are multiple descriptors for a particular type in a clear virtual
link we receive, we will not process it correctly but rather take the last
value. This can cause us not to not flap the virtual link as the value from
the descriptors that we compare against the our stored FCF or fc_lport values
may not match.
Change this to do a comparison when processing the each descriptor instead of at
the end and then set a bool if we need to do the reset.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Wed, 31 May 2017 13:33:50 +0000 (06:33 -0700)]
scsi: qedf: Honor qed_ops->common->set_fp_int() return code.
We need to check the return code the set_fp_int() callback in case we were
not allocated any fastpath interrupts or there was an error setting up the
fastpath interrupts from the qed perspective.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Wed, 31 May 2017 13:33:49 +0000 (06:33 -0700)]
scsi: qedf: Update copyright to 2017.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Wed, 31 May 2017 13:33:48 +0000 (06:33 -0700)]
scsi: qedf: Enable basic FDMI information.
For libfc to register FDMI attributes we need to do two things:
- Set the appropriate fc_host attributes that libfc will use to form the
FDMI registration commands
- Set lport->fdmi_enabled to 1
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Varun Prakash [Thu, 1 Jun 2017 07:18:33 +0000 (12:48 +0530)]
scsi: csiostor: add check for supported fw version
T6 FCoE support is added in fw version 1.16.45.0 so return error if fw
version < 1.16.45.0 for T6 adapters.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Milan P. Gandhi [Thu, 1 Jun 2017 12:08:55 +0000 (17:38 +0530)]
scsi: fcoe: Remove an extra out label in _fcoe_create function
This patch removes an extra out label in _fcoe_create function where we
return if creation of FCOE interface is failed.
Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Milan P. Gandhi [Thu, 1 Jun 2017 12:05:49 +0000 (17:35 +0530)]
scsi: fcoe: Fix few small typos in fcoe.c
This patch does a cleanup and fixes few small typos in fcoe.c
Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Fri, 26 May 2017 10:11:37 +0000 (11:11 +0100)]
scsi: lpfc: fix spelling mistake "entrys" -> "entries"
Trivial fix to spelling mistake in debugfs message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Mon, 22 May 2017 20:10:53 +0000 (13:10 -0700)]
scsi: qla2xxx: Remove an unused structure member
qla_tgt_cmd.free_work is not used by the qla2xxx driver. Hence remove
that member of struct qla_tgt_cmd.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Quinn Tran <quinn.tran@cavium.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gustavo A. R. Silva [Mon, 22 May 2017 18:00:29 +0000 (13:00 -0500)]
scsi: hisi_sas: add null check before indirect pointer dereference
Add null check before indirectly dereferencing pointer task->lldd_task
in statement u32 tag = slot->idx;
Addresses-Coverity-ID:
1373843
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Thu, 18 May 2017 08:32:18 +0000 (10:32 +0200)]
scsi: smartpqi: mark PM functions as __maybe_unused
The newly added suspend/resume support causes harmless warnings when
CONFIG_PM is disabled:
smartpqi/smartpqi_init.c:5147:12: error: 'pqi_ctrl_wait_for_pending_io' defined but not used [-Werror=unused-function]
smartpqi/smartpqi_init.c:2019:13: error: 'pqi_wait_until_lun_reset_finished' defined but not used [-Werror=unused-function]
smartpqi/smartpqi_init.c:2013:13: error: 'pqi_wait_until_scan_finished' defined but not used [-Werror=unused-function]
We can avoid the warnings by removing the #ifdef around the handlers and
instead marking them as __maybe_unused, which will let gcc drop the
unused code silently.
Fixes:
f44d210312a6 ("scsi: smartpqi: add suspend and resume support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kees Cook [Tue, 9 May 2017 22:34:44 +0000 (15:34 -0700)]
scsi: csiostor: Avoid content leaks and casts
When copying attributes, the len argument was padded out and the
resulting memcpy() would copy beyond the end of the source buffer.
Avoid this, and use size_t for val_len to avoid all the casts.
Similarly, avoid source buffer casts and use void *.
Additionally enforces val_len can be represented by u16 and that the DMA
buffer was not overflowed. Fixes the size of mfa, which is not
FC_FDMI_PORT_ATTR_MAXFRAMESIZE_LEN (but it will be padded up to 4). This
was noticed by the future CONFIG_FORTIFY_SOURCE checks.
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stephen Hemminger [Thu, 18 May 2017 16:18:12 +0000 (09:18 -0700)]
scsi: storvsc: remove unnecessary channel inbound lock
In storvsc driver, inbound messages do not go through inbound lock. The
only effect of this lock was is to provide a barrier for connect and
remove logic.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stephen Hemminger [Thu, 18 May 2017 16:18:11 +0000 (09:18 -0700)]
scsi: storvsc: use in place iterator function
In 4.12-rc1, new functions were added to support iterating over elements
in the vmbus event ring. This patch uses them to simplify the ring
buffer handling in virtual SCSI driver as well.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Varun Prakash [Thu, 18 May 2017 14:47:38 +0000 (20:17 +0530)]
scsi: csiostor: add support for Chelsio T6 adapters
Enable probe for T6 adapters, add code to flash T6 firmware and firmware
config file, use T6 specific macros.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kyle Fortin [Wed, 17 May 2017 20:21:54 +0000 (16:21 -0400)]
scsi: libiscsi: use kvzalloc for iscsi_pool_init
iscsiadm session login can fail with the following error:
iscsiadm: Could not login to [iface: default, target: iqn.1986-03.com...
iscsiadm: initiator reported error (9 - internal error)
When /etc/iscsi/iscsid.conf sets node.session.cmds_max = 4096, it
results in 64K-sized kmallocs per session. A system under fragmented
slab pressure may not have any 64K objects available and fail iscsiadm
session login. Even though memory objects of a smaller size are
available, the large order allocation ends up failing.
The kernel prints a warning and does dump_stack, like below:
iscsid: page allocation failure: order:4, mode:0xc0d0
CPU: 0 PID: 2456 Comm: iscsid Not tainted 4.1.12-61.1.28.el6uek.x86_64 #2
Call Trace:
[<
ffffffff816c6e40>] dump_stack+0x63/0x83
[<
ffffffff8118e58a>] warn_alloc_failed+0xea/0x140
[<
ffffffff81191df9>] __alloc_pages_slowpath+0x409/0x760
[<
ffffffff81192401>] __alloc_pages_nodemask+0x2b1/0x2d0
[<
ffffffffa048f6c0>] ? dev_attr_host_ipaddress+0x20/0xffffffffffffc722
[<
ffffffff811dc38f>] alloc_pages_current+0xaf/0x170
[<
ffffffff81192581>] alloc_kmem_pages+0x31/0xd0
[<
ffffffffa048f600>] ? iscsi_transport_group+0x20/0xffffffffffffc7e2
[<
ffffffff811ad738>] kmalloc_order+0x18/0x50
[<
ffffffff811ad7a4>] kmalloc_order_trace+0x34/0xe0
[<
ffffffff8146ee30>] ? transport_remove_classdev+0x70/0x70
[<
ffffffff811e843d>] __kmalloc+0x27d/0x2a0
[<
ffffffff810c8cbd>] ? complete_all+0x4d/0x60
[<
ffffffffa04af299>] iscsi_pool_init+0x69/0x160 [libiscsi]
[<
ffffffff81465d90>] ? device_initialize+0xb0/0xd0
[<
ffffffffa04af510>] iscsi_session_setup+0x180/0x2f4 [libiscsi]
[<
ffffffffa04c5a60>] ? iscsi_max_lun+0x20/0xfffffffffffffa9e [iscsi_tcp]
[<
ffffffffa04c531f>] iscsi_sw_tcp_session_create+0xcf/0x150 [iscsi_tcp]
[<
ffffffffa04c5a60>] ? iscsi_max_lun+0x20/0xfffffffffffffa9e [iscsi_tcp]
[<
ffffffffa048a633>] iscsi_if_create_session+0x33/0xd0
[<
ffffffffa04c5a60>] ? iscsi_max_lun+0x20/0xfffffffffffffa9e [iscsi_tcp]
[<
ffffffffa048abd8>] iscsi_if_recv_msg+0x508/0x8c0 [scsi_transport_iscsi]
[<
ffffffff811922eb>] ? __alloc_pages_nodemask+0x19b/0x2d0
[<
ffffffff811e6d69>] ? __kmalloc_node_track_caller+0x209/0x2c0
[<
ffffffffa048b00c>] iscsi_if_rx+0x7c/0x200 [scsi_transport_iscsi]
[<
ffffffff81623dc6>] netlink_unicast+0x126/0x1c0
[<
ffffffff8162468c>] netlink_sendmsg+0x36c/0x400
[<
ffffffff815d2fed>] sock_sendmsg+0x4d/0x60
[<
ffffffff815d596a>] ___sys_sendmsg+0x30a/0x330
[<
ffffffff811bc72c>] ? handle_pte_fault+0x20c/0x230
[<
ffffffff811bc90c>] ? __handle_mm_fault+0x1bc/0x330
[<
ffffffff811bcb32>] ? handle_mm_fault+0xb2/0x1a0
[<
ffffffff815d5b99>] __sys_sendmsg+0x49/0x90
[<
ffffffff815d5bf9>] SyS_sendmsg+0x19/0x20
[<
ffffffff816cbb2e>] system_call_fastpath+0x12/0x71
Use kvzalloc for iscsi_pool in iscsi_pool_init.
Signed-off-by: Kyle Fortin <kyle.fortin@oracle.com>
Tested-by: Kyle Fortin <kyle.fortin@oracle.com>
Reviewed-by: Joseph Slember <joe.slember@oracle.com>
Reviewed-by: Lance Hartmann <lance.hartmann@oracle.com>
Acked-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:55:55 +0000 (18:55 -0500)]
scsi: smartpqi: bump driver version
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Corentin Labbe [Wed, 3 May 2017 23:55:49 +0000 (18:55 -0500)]
scsi: smartpqi: remove writeq/readq function definitions
Instead of rewriting write/readq, use existing functions
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:55:43 +0000 (18:55 -0500)]
scsi: smartpqi: add module parameters
Add module parameters to disable heartbeat support and to disable
shutting down the controller when a controller is taken offline.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:55:37 +0000 (18:55 -0500)]
scsi: smartpqi: cleanup list initialization
Better initialization of linked list heads.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:55:31 +0000 (18:55 -0500)]
scsi: smartpqi: add raid level show
Display the RAID level via sysfs
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:55:25 +0000 (18:55 -0500)]
scsi: smartpqi: make ioaccel references consistent
- make all references to RAID bypass consistent throughout driver.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:55:19 +0000 (18:55 -0500)]
scsi: smartpqi: enhance device add and remove messages
Improved formatting of information displayed when devices
are added/removed from the system.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:55:13 +0000 (18:55 -0500)]
scsi: smartpqi: update timeout on admin commands
Increase the timeout on admin commands from 3 seconds to 60
seconds and added a check for controller crash in the loop
where the driver polls for admin command completion.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:55:07 +0000 (18:55 -0500)]
scsi: smartpqi: map more raid errors to SCSI errors
enhance mapping of RAID path errors to Linux SCSI host
error codes.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:55:01 +0000 (18:55 -0500)]
scsi: smartpqi: cleanup controller branding
- Improve controller branding support.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:54:55 +0000 (18:54 -0500)]
scsi: smartpqi: update rescan worker
improve support for taking controller offline.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:54:49 +0000 (18:54 -0500)]
scsi: smartpqi: update device offline
- Improve handling of offline devices.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:54:43 +0000 (18:54 -0500)]
scsi: smartpqi: correct aio error path
set the internal flag that causes I/O to be sent down the
RAID path when the AIO path is disabled
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:54:37 +0000 (18:54 -0500)]
scsi: smartpqi: add lockup action
add support for actions to take when controller goes offline.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:54:31 +0000 (18:54 -0500)]
scsi: smartpqi: remove qdepth calculations for logical volumes
make the queue depth for LVs the same as the maximum
I/Os supported by the controller
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:54:25 +0000 (18:54 -0500)]
scsi: smartpqi: enhance kdump
constrain resource usage during kdump to avoid kdump failures
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 3 May 2017 23:54:18 +0000 (18:54 -0500)]
scsi: smartpqi: change return value for LUN reset operations
change return value for controller offline to be consistent
with the rest of the driver.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>