OSDN Git Service
Mark Edwards [Tue, 14 Apr 2015 12:52:34 +0000 (08:52 -0400)]
USB: cp210x: add ID for KCF Technologies PRN device
commit
c735ed74d83f8ecb45c4c4c95a16853c9c3c8157 upstream.
Added the USB serial console device ID for KCF Technologies PRN device
which has a USB port for its serial console.
Signed-off-by: Mark Edwards <sonofaforester@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jason A. Donenfeld [Wed, 22 Apr 2015 12:35:08 +0000 (14:35 +0200)]
USB: pl2303: Remove support for Samsung I330
commit
48ef23a4f686b1e4519d4193c20d26834ff810ff upstream.
This phone is already supported by the visor driver.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jason A. Donenfeld [Wed, 22 Apr 2015 12:35:09 +0000 (14:35 +0200)]
USB: visor: Match I330 phone more precisely
commit
82ee3aeb9295c5fc37fd2ddf20f13ac2b40ec97d upstream.
Samsung has just released a portable USB3 SSD, coming in a very small
and nice form factor. It's USB ID is 04e8:8001, which unfortunately is
already used by the Palm Visor driver for the Samsung I330 phone cradle.
Having pl2303 or visor pick up this device ID results in conflicts with
the usb-storage driver, which handles the newly released portable USB3
SSD.
To work around this conflict, I've dug up a mailing list post [1] from a
long time ago, in which a user posts the full USB descriptor
information. The most specific value in this appears to be the interface
class, which has value 255 (0xff). Since usb-storage requires an
interface class of 0x8, I believe it's correct to disambiguate the two
devices by matching on 0xff inside visor.
[1] http://permalink.gmane.org/gmane.linux.usb.user/4264
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joe Lawrence [Thu, 30 Apr 2015 14:16:04 +0000 (17:16 +0300)]
xhci: gracefully handle xhci_irq dead device
commit
948fa13504f80b9765d2b753691ab94c83a10341 upstream.
If the xHCI host controller has died (ie, device removed) or suffered
other serious fatal error (STS_FATAL), then xhci_irq should handle this
condition with IRQ_HANDLED instead of -ESHUTDOWN.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Thu, 30 Apr 2015 14:16:03 +0000 (17:16 +0300)]
xhci: Solve full event ring by increasing TRBS_PER_SEGMENT to 256
commit
18cc2f4cbbaf825a4fedcf2d60fd388d291e0a38 upstream.
Our event ring consists of only one segment, and we risk filling
the event ring in case we get isoc transfers with short intervals
such as webcams that fill a TD every microframe (125us)
With 64 TRB segment size one usb camera could fill the event ring in 8ms.
A setup with several cameras and other devices can fill up the
event ring as it is shared between all devices.
This has occurred when uvcvideo queues 5 * 32TD URBs which then
get cancelled when the video mode changes. The cancelled URBs are returned
in the xhci interrupt context and blocks the interrupt handler from
handling the new events.
A full event ring will block xhci from scheduling traffic and affect all
devices conneted to the xhci, will see errors such as Missed Service
Intervals for isoc devices, and and Split transaction errors for LS/FS
interrupt devices.
Increasing the TRB_PER_SEGMENT will also increase the default endpoint ring
size, which is welcome as for most isoc transfer we had to dynamically
expand the endpoint ring anyway to be able to queue the 5 * 32TDs uvcvideo
queues.
The default size used to be 64 TRBs per segment
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Thu, 30 Apr 2015 14:16:02 +0000 (17:16 +0300)]
xhci: fix isoc endpoint dequeue from advancing too far on transaction error
commit
d104d0152a97fade389f47635b73a9ccc7295d0b upstream.
Isoc TDs usually consist of one TRB, sometimes two. When all goes well we
receive only one success event for a TD, and move the dequeue pointer to
the next TD.
This fails if the TD consists of two TRBs and we get a transfer error
on the first TRB, we will then see two events for that TD.
Fix this by making sure the event we get is for the last TRB in that TD
before moving the dequeue pointer to the next TD. This will resolve some
of the uvc and dvb issues with the
"ERROR Transfer event TRB DMA ptr not part of current TD" error message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Grover [Fri, 22 May 2015 21:07:44 +0000 (14:07 -0700)]
target/pscsi: Don't leak scsi_host if hba is VIRTUAL_HOST
commit
5a7125c64def3b21f8147eca8b54949a60963942 upstream.
See https://bugzilla.redhat.com/show_bug.cgi?id=
1025672
We need to put() the reference to the scsi host that we got in
pscsi_configure_device(). In VIRTUAL_HOST mode it is associated with
the dev_virt, not the hba_virt.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephane Eranian [Thu, 23 Apr 2015 07:07:09 +0000 (09:07 +0200)]
perf/x86/rapl: Enable Broadwell-U RAPL support
commit
44b11fee51711ca85aa2b121a49bf029d18a3722 upstream.
This patch enables RAPL counters (energy consumption counters)
support for Intel Broadwell-U processors (Model 61):
To use:
$ perf stat -a -I 1000 -e power/energy-cores/,power/energy-pkg/,power/energy-ram/ sleep 10
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jacob.jun.pan@linux.intel.com
Cc: kan.liang@intel.com
Cc: peterz@infradead.org
Cc: sonnyrao@chromium.org
Link: http://lkml.kernel.org/r/20150423070709.GA4970@thinkpad
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Malcolm Priestley [Tue, 21 Apr 2015 21:33:02 +0000 (22:33 +0100)]
staging: vt6655: lock MACvWriteBSSIDAddress.
commit
664a5c1d1e33cd89cb7883e8c74638cc482b5da7 upstream.
This function selects page 1 and cause intermittent problems on
interrupt handler.
lock call with spin_lock_irqsave.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Malcolm Priestley [Tue, 21 Apr 2015 21:33:00 +0000 (22:33 +0100)]
staging: vt6655: vnt_tx_packet Correct TX order of OWNED_BY_NIC
commit
d65d2b25d2761153390df8026cca1a528d9b6c5a upstream.
The state of m_td0TD0.f1Owner should change after the buff_addr
has been filled otherwise the device grabs the buffer too early.
m_td0TD0.f1Owner is protected by memory barriers on both sides
of change.
iTDUsed is best incremented after MACvTransmit.
It appears that f1Owner actually polls to do the memory transfer.
A back port patch will be needed for v3.19
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Malcolm Priestley [Sat, 11 Apr 2015 19:29:41 +0000 (20:29 +0100)]
staging: vt6655: Fix 80211 control and management status reporting.
commit
ad3fee9b17b90b8f1ac94b615111b2f14dd90adb upstream.
Currently only TD_FLAGS_NETIF_SKB are reported back to mac80211.
Move vnt_int_report_rate to report all frame types.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Malcolm Priestley [Thu, 9 Apr 2015 19:53:44 +0000 (20:53 +0100)]
staging: vt6655: implement IEEE80211_TX_STAT_NOACK_TRANSMITTED
commit
6e44dc4be009eef60a1744e4a4b830131f6b9a8e upstream.
Make use of this macro for non ack frames.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Malcolm Priestley [Thu, 9 Apr 2015 19:53:43 +0000 (20:53 +0100)]
staging: vt6655: device_free_tx_buf use only ieee80211_tx_status_irqsafe
commit
3fa0917beb29d886550fcf61a6378563d1ce9684 upstream.
TD_FLAGS_NETIF_SKB is only for data.
Fixes issue of ack frames not being reported.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Malcolm Priestley [Sat, 4 Apr 2015 19:49:10 +0000 (20:49 +0100)]
staging: vt6656: use ieee80211_tx_info to select packet type.
commit
b23f14302e86628625ac3982a6d23e35888755f2 upstream.
Information for packet type is in ieee80211_tx_info
band IEEE80211_BAND_5GHZ for PK_TYPE_11A.
IEEE80211_TX_RC_USE_CTS_PROTECT via tx_rate flags selects PK_TYPE_11GB
This ensures that the packet is always the right type.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sławomir Demeszko [Tue, 5 May 2015 15:49:54 +0000 (17:49 +0200)]
staging: gdm724x: Correction of variable usage after applying ALIGN()
commit
892c89d5d7ffd1bb794fe54d86c0eef18d215fab upstream.
Fix regression introduced by commit <
29ef8a53542a>. After it writing
AT commands to /dev/GCT-ATM0 is unsuccessful (no echo, no response)
and dmesg show "gdmtty: invalid payload : 1 16 f011".
Before that commit value of dummy_cnt was only a padding size. After using
ALIGN() this value is increased by its first argument. So the following
usage of this variable needs correction.
Signed-off-by: Sławomir Demeszko <s.demeszko@wireless-instruments.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tatyana Nikolova [Fri, 8 May 2015 21:36:33 +0000 (16:36 -0500)]
RDMA/core: Fix for parsing netlink string attribute
commit
ec04847c0c5b471bab2dacceadfdb803a9d1a2ea upstream.
The string iwpm_ulib_name is recorded in a nlmsg as a netlink attribute.
Without this fix parsing of the nlmsg by the userspace port mapper service fails
because of unknown attribute length, causing the port mapper service not to
register the client, which has sent the nlmsg.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zidan Wang [Tue, 12 May 2015 06:58:50 +0000 (14:58 +0800)]
ASoC: wm8994: correct BCLK DIV 348 to 384
commit
17fc2e0a3db11889e942c5ab15a1fcb876638f25 upstream.
According to the RM of wm8958, BCLK DIV 348 doesn't exist, correct it
to 384.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zidan Wang [Tue, 12 May 2015 06:58:36 +0000 (14:58 +0800)]
ASoC: wm8960: fix "RINPUT3" audio route error
commit
85e36a1f4a735d991ba5106781ea48e89a0b8901 upstream.
It should be "RINPUT3" instead of "LINPUT3" route to "Right Input
Mixer".
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Koro Chen [Mon, 11 May 2015 02:36:53 +0000 (10:36 +0800)]
ASoC: dapm: Modify widget stream name according to prefix
commit
fdb6eb0a12871d5bfaf266c5a0d5259a5437a72f upstream.
When there is prefix specified, currently we will add this prefix in
widget->name, but not in widget->sname.
it causes failure at snd_soc_dapm_link_dai_widgets:
if (!w->sname || !strstr(w->sname, dai_w->name))
because dai_w->name has prefix added, but w->sname does not.
We should also add prefix for stream name
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vasily Khoruzhick [Sun, 3 May 2015 18:11:47 +0000 (21:11 +0300)]
ASoC: uda1380: Avoid accessing i2c bus when codec is disabled
commit
810e4425c224af6be67dff68c8832af1b5a11f89 upstream.
set_dai_fmt_both() callback is called from snd_soc_runtime_set_dai_fmt()
which is called from snd_soc_register_card(), but at this time codec
is not powered on yet. Replace direct i2c write with regcache write.
Fixes:
5f0acedddf533c (ASoC: rx1950_uda1380: Use static DAI format setup)
Fixes:
5cc10b9b77c234 (ASoC: h1940_uda1380: Use static DAI format setup)
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Axel Lin [Mon, 27 Apr 2015 06:51:35 +0000 (14:51 +0800)]
ASoC: mc13783: Fix wrong mask value used in mc13xxx_reg_rmw() calls
commit
545774bd6e1427d98dde77244329d2311c5eca6f upstream.
mc13xxx_reg_rmw() won't change any bit if passing 0 to the mask field.
Pass AUDIO_SSI_SEL instead of 0 for the mask field to set AUDIO_SSI_SEL
bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Wed, 27 May 2015 14:17:19 +0000 (16:17 +0200)]
ALSA: hda - Fix noise on AMD radeon 290x controller
commit
0fa372b6c95013af1334b3d5c9b5f03a70ecedab upstream.
A new AMD controller [1002:aac8] seems to need the quirk for other AMD
NS HDMI stuff, otherwise it gives noisy sounds.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99021
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Sun, 24 May 2015 06:27:52 +0000 (08:27 +0200)]
Revert "ALSA: hda - Add mute-LED mode control to Thinkpad"
commit
3530febb5c7636f6b26d15637f68296804d26491 upstream.
This reverts commit
7290006d8c0900c56d8c58428134f02c35109d17.
Through the regression report, it was revealed that the
tpacpi_led_set() call to thinkpad_acpi helper doesn't only toggle the
mute LED but actually mutes the sound. This is contradiction to the
expectation, and rather confuses user.
According to Henrique, it's not trivial to judge which TP model
behaves "LED-only" and which model does whatever more intrusive, as
Lenovo's implementations vary model by model. So, from the safety
reason, we should revert the patch for now.
Reported-by: Martin Steigerwald <martin@lichtvoll.de>
Cc: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vittorio G (VittGam) [Fri, 22 May 2015 19:15:19 +0000 (21:15 +0200)]
ALSA: usb-audio: Add quirk for MS LifeCam HD-3000
commit
ae425bb2a05bebe786a25cc8ae64e9d16c4d9b83 upstream.
Microsoft LifeCam HD-3000 (045e:0779) needs a similar quirk for
suppressing the unsupported sample rate inquiry.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98481
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ansgar Hegerfeld [Thu, 14 May 2015 10:31:32 +0000 (12:31 +0200)]
ALSA: hda/realtek - ALC292 dock fix for Thinkpad L450
commit
09ea997677cd44ebe7f42573119aaf46b775c683 upstream.
The Lenovo ThinkPad L450 requires the ALC292_FIXUP_TPT440_DOCK fix in
order to get sound output on the docking stations audio port.
This patch was tested using a ThinkPad L450 (20DSS00B00) using kernel
4.0.3 and a ThinkPad Pro Dock.
Signed-off-by: Ansgar Hegerfeld <linux@hegerfeld.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Henningsson [Mon, 11 May 2015 12:04:14 +0000 (14:04 +0200)]
ALSA: hda - Add headset mic quirk for Dell Inspiron 5548
commit
9b5a4e395c2f39fae89f75e4a749be5dba342d22 upstream.
This enables the headset microphone on Dell Inspiron 5548,
or at least some variants of it.
BugLink: https://bugs.launchpad.net/bugs/1452175
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Fri, 1 May 2015 07:20:34 +0000 (09:20 +0200)]
ALSA: hda - Add headphone quirk for Lifebook E752
commit
88776f366ede7d9cdce60bd2c9753dd6d6fa8b77 upstream.
Fujitsu Lifebook E752 laptop needs a similar quirk done for Lifebook
T731. Otherwise the headphone is always muted.
Reported-and-tested-by: Christian Weber <we_chris@hotmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Henningsson [Wed, 13 May 2015 11:28:54 +0000 (13:28 +0200)]
ALSA: hda - Add Conexant codecs CX20721, CX20722, CX20723 and CX20724
commit
6ffc0898b29a2811a6c0569c5dd9b581980110df upstream.
This patch adds support for Conexant HD Audio codecs
CX20721, CX20722, CX20723 and CX20724.
BugLink: https://bugs.launchpad.net/bugs/1454656
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 19 May 2015 08:46:49 +0000 (10:46 +0200)]
ALSA: usb-audio: Add quirk for MS LifeCam Studio
commit
fa94b0d72511add5822dc4124f2a3eae66b8863f upstream.
Microsoft LifeCam Studio (045e:0772) needs a similar quirk for
suppressing the wrong sample rate inquiry.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98481
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steven Rostedt [Fri, 8 May 2015 17:36:23 +0000 (03:06 +0930)]
module: Call module notifier on failure after complete_formation()
commit
37815bf866ab6722a47550f8d25ad3f1a16a680c upstream.
The module notifier call chain for MODULE_STATE_COMING was moved up before
the parsing of args, into the complete_formation() call. But if the module failed
to load after that, the notifier call chain for MODULE_STATE_GOING was
never called and that prevented the users of those call chains from
cleaning up anything that was allocated.
Link: http://lkml.kernel.org/r/554C52B9.9060700@gmail.com
Reported-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Fixes:
4982223e51e8 "module: set nx before marking module MODULE_STATE_COMING"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro [Fri, 29 May 2015 03:09:19 +0000 (23:09 -0400)]
d_walk() might skip too much
commit
2159184ea01e4ae7d15f2017e296d4bc82d5aeb0 upstream.
when we find that a child has died while we'd been trying to ascend,
we should go into the first live sibling itself, rather than its sibling.
Off-by-one in question had been introduced in "deal with deadlock in
d_walk()" and the fix needs to be backported to all branches this one
has been backported to.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Tue, 2 Jun 2015 15:10:28 +0000 (17:10 +0200)]
lib: Fix strnlen_user() to not touch memory after specified maximum
commit
f18c34e483ff6b1d9866472221e4015b3a4698e4 upstream.
If the specified maximum length of the string is a multiple of unsigned
long, we would load one long behind the specified maximum. If that
happens to be in a next page, we can hit a page fault although we were
not expected to.
Fix the off-by-one bug in the test whether we are at the end of the
specified range.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arend van Spriel [Tue, 26 May 2015 11:19:46 +0000 (13:19 +0200)]
brcmfmac: avoid null pointer access when brcmf_msgbuf_get_pktid() fails
commit
7d072b404c5d8f1e0b62b6bc488dfeaa61bd2d8d upstream.
The function brcmf_msgbuf_get_pktid() may return a NULL pointer so
the callers should check the return pointer before accessing it to
avoid the crash below (see [1]):
brcmfmac: brcmf_msgbuf_get_pktid: Invalid packet id 273 (not in use)
BUG: unable to handle kernel NULL pointer dereference at
0000000000000080
IP: [<
ffffffff8145b225>] skb_pull+0x5/0x50
PGD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: pci_stub vboxpci(O) vboxnetflt(O) vboxnetadp(O) vboxdrv(O)
snd_hda_codec_hdmi bnep mousedev hid_generic ushwmon msr ext4 crc16 mbcache
jbd2 sd_mod uas usb_storage ahci libahci libata scsi_mod xhci_pci xhci_hcd
usbcore usb_common
CPU: 0 PID: 1661 Comm: irq/61-brcmf_pc Tainted: G O 4.0.1-MacbookPro-ARCH #1
Hardware name: Apple Inc. MacBookPro12,1/Mac-
E43C1C25D4880AD6,
BIOS MBP121.88Z.0167.B02.
1503241251 03/24/2015
task:
ffff880264203cc0 ti:
ffff88025ffe4000 task.ti:
ffff88025ffe4000
RIP: 0010:[<
ffffffff8145b225>] [<
ffffffff8145b225>] skb_pull+0x5/0x50
RSP: 0018:
ffff88025ffe7d40 EFLAGS:
00010202
RAX:
0000000000000000 RBX:
ffff88008a33c000 RCX:
0000000000000044
RDX:
0000000000000000 RSI:
000000000000004a RDI:
0000000000000000
RBP:
ffff88025ffe7da8 R08:
0000000000000096 R09:
000000000000004a
R10:
0000000000000000 R11:
000000000000048e R12:
ffff88025ff14f00
R13:
0000000000000000 R14:
ffff880263b48200 R15:
ffff88008a33c000
FS:
0000000000000000(0000) GS:
ffff88026ec00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000000000080 CR3:
000000000180b000 CR4:
00000000003407f0
Stack:
ffffffffa06aed74 ffff88025ffe7dc8 ffff880263b48270 ffff880263b48278
05ea88020000004a 0002ffff81014635 000000001720b2f6 ffff88026ec116c0
ffff880263b48200 0000000000010000 ffff880263b4ae00 ffff880264203cc0
Call Trace:
[<
ffffffffa06aed74>] ? brcmf_msgbuf_process_rx+0x404/0x480 [brcmfmac]
[<
ffffffff810cea60>] ? irq_finalize_oneshot.part.30+0xf0/0xf0
[<
ffffffffa06afb55>] brcmf_proto_msgbuf_rx_trigger+0x35/0xf0 [brcmfmac]
[<
ffffffffa06baf2a>] brcmf_pcie_isr_thread_v2+0x8a/0x130 [brcmfmac]
[<
ffffffff810cea80>] irq_thread_fn+0x20/0x50
[<
ffffffff810ceddf>] irq_thread+0x13f/0x170
[<
ffffffff810cebf0>] ? wake_threads_waitq+0x30/0x30
[<
ffffffff810ceca0>] ? irq_thread_dtor+0xb0/0xb0
[<
ffffffff81092a08>] kthread+0xd8/0xf0
[<
ffffffff81092930>] ? kthread_create_on_node+0x1c0/0x1c0
[<
ffffffff8156d898>] ret_from_fork+0x58/0x90
[<
ffffffff81092930>] ? kthread_create_on_node+0x1c0/0x1c0
Code: 01 83 e2 f7 88 50 01 48 83 c4 08 5b 5d f3 c3 0f 1f 80 00 00 00 00 83 e2
f7 88 50 01 c3 66 0f 1f 84 00 00 00 00 00 0f 1f
RIP [<
ffffffff8145b225>] skb_pull+0x5/0x50
RSP <
ffff88025ffe7d40>
CR2:
0000000000000080
---[ end trace
b074c0f90e7c997d ]---
[1] http://mid.gmane.org/
20150430193259.GA5630@googlemail.com
Reported-by: Michael Hornung <mhornung.linux@gmail.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dong Aisheng [Wed, 15 Apr 2015 14:26:36 +0000 (22:26 +0800)]
clk: add missing lock when call clk_core_enable in clk_set_parent
commit
d2a5d46b167a9a8231264daf80165b739aecf1d7 upstream.
Before commit
035a61c314eb ("clk: Make clk API return per-user
struct clk instances") we acquired the enable_lock in
__clk_set_parent_{before,after}() by means of calling
clk_enable(). After commit
035a61c314eb we use clk_core_enable()
in place of the clk_enable(), and clk_core_enable() doesn't
acquire the enable_lock. This opens up a race condition between
clk_set_parent() and clk_enable(). Fix it.
Fixes:
035a61c314eb ("clk: Make clk API return per-user struct clk instances")
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Javier Martinez Canillas [Wed, 8 Apr 2015 05:34:12 +0000 (07:34 +0200)]
clk: exynos5420: Restore GATE_BUS_TOP on suspend
commit
97372e5a99449b4fffa824a382ad6358066a9918 upstream.
Commit
ae43b3289186 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power
Management support v12") added pm support for the pl330 dma driver but
it makes the clock for the Exynos5420 MDMA0 DMA controller to be gated
during suspend and this in turn makes its parent clock aclk266_g2d to
be gated. But the clock needs to be ungated prior suspend to allow the
system to be suspend and resumed correctly.
Add GATE_BUS_TOP register to the list of registers to be restored when
the system enters into a suspend state so aclk266_g2d will be ungated.
Thanks to Abhilash Kesavan for figuring out that this was the issue.
Fixes:
ae43b32 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power Management support v12")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter Roeck [Thu, 28 May 2015 16:12:23 +0000 (09:12 -0700)]
hwmon: (nct6683) Add missing sysfs attribute initialization
commit
c7bd6dc320b85445b6b36a0aff41f929210027c7 upstream.
The following error message is seen when loading the nct6683 driver
with DEBUG_LOCK_ALLOC enabled.
BUG: key
ffff88040b2f0030 not in .data!
------------[ cut here ]------------
WARNING: CPU: 0 PID: 186 at kernel/locking/lockdep.c:2988
lockdep_init_map+0x469/0x630()
DEBUG_LOCKS_WARN_ON(1)
Caused by a missing call to sysfs_attr_init() when initializing
sysfs attributes.
Reported-by: Alexey Orishko <alexey.orishko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter Roeck [Thu, 28 May 2015 16:08:09 +0000 (09:08 -0700)]
hwmon: (nct6775) Add missing sysfs attribute initialization
commit
1b63bf617206ff35b93c57c67bbe067ac735a85a upstream.
The following error message is seen when loading the nct6775 driver
with DEBUG_LOCK_ALLOC enabled.
BUG: key
ffff88040b2f0030 not in .data!
------------[ cut here ]------------
WARNING: CPU: 0 PID: 186 at kernel/locking/lockdep.c:2988
lockdep_init_map+0x469/0x630()
DEBUG_LOCKS_WARN_ON(1)
Caused by a missing call to sysfs_attr_init() when initializing
sysfs attributes.
Reported-by: Alexey Orishko <alexey.orishko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter Roeck [Wed, 27 May 2015 23:11:48 +0000 (16:11 -0700)]
hwmon: (tmp401) Do not auto-detect chip on I2C address 0x37
commit
9aecac04d8d89e730ae362a748113b19c06a9d39 upstream.
I2C address 0x37 may be used by EEPROMs, which can result in false
positives. Do not attempt to detect a chip at this address.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Betker [Wed, 15 Apr 2015 19:11:50 +0000 (21:11 +0200)]
iio: adc: xilinx: Fix VREFN sign
commit
97ffae1d30c3f6ceee67d5b0d3e540c08c13c744 upstream.
The VREFN channel is bipolar, not unipolar. Small negative values do
occur (e.g., -1mV), and unsigned conversion maps them incorrectly to
large positive values (about +1V), so fix this.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Betker [Wed, 15 Apr 2015 19:11:49 +0000 (21:11 +0200)]
iio: adc: xilinx: Fix VREFP scale
commit
00db4e52f4541965f7fda225eb458a75f892017b upstream.
The scaling factor for VREFP is 3.0/4096, not 1.0/4096; fix this to get
correct readings.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Betker [Wed, 15 Apr 2015 19:11:48 +0000 (21:11 +0200)]
iio: adc: xilinx: Fix "vccaux" channel .address
commit
d6c96c42283601e311a7a1a3d7e51cde9d7fdb6e upstream.
For the "vccaux" channel, read the VCCAUX register, not VCCINT.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Betker [Wed, 15 Apr 2015 19:11:47 +0000 (21:11 +0200)]
iio: adc: xilinx: Fix register addresses
commit
3960d2c0c4aafe98da47a4a2eb64dfa8e88d8df5 upstream.
Define the register addresses for MIN_VCCPINT, MIN_VCCPAUX, MIN_VCCO_DDR
correctly.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Naidu Tellapati [Thu, 7 May 2015 21:22:19 +0000 (18:22 -0300)]
iio: adc:
cc10001: Fix regulator_get_voltage() return value check
commit
65a761bf8d55fdcf8ecc4642382a4e76c086e44c upstream.
regulator_get_voltage() returns a non-negative value in case of success,
and a negative error in case of error. Let's fix this.
Fixes:
1664f6a5b0c8 ("iio: adc: Cosmic Circuits 10001 ADC driver")
Signed-off-by: Naidu Tellapati <naidu.tellapati@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Naidu Tellapati [Thu, 7 May 2015 21:22:20 +0000 (18:22 -0300)]
iio: adc:
cc10001: Add delay before setting START bit
commit
f29b212edb9e253cafcb4a2ab7842a890989f1a5 upstream.
According to hardware team there should be some delay after
setting channel number, start mode and before setting START.
Add a one microsecond delay for this purpose.
Fixes:
1664f6a5b0c8 ("iio: adc: Cosmic Circuits 10001 ADC driver")
Signed-off-by: Naidu Tellapati <naidu.tellapati@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Naidu Tellapati [Thu, 7 May 2015 21:22:18 +0000 (18:22 -0300)]
iio: adc:
cc10001: Fix incorrect use of power-up/power-down register
commit
713276ea88a295a79aa6633ba639ed47692a8de4 upstream.
At present we are incorrectly setting the register to 0x1 to power up
the ADC. Since it is an active high power down register, we need to set
the register to 0x0 to actually power up. Conversely, writing 0x1 to the
register powers it down.
This commit adds a couple of helpers to make the code clearer and then
use them to do the power-up/power-down properly.
Fixes:
1664f6a5b0c8 ("iio: adc: Cosmic Circuits 10001 ADC driver")
Signed-off-by: Naidu Tellapati <naidu.tellapati@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Naidu Tellapati [Thu, 7 May 2015 21:22:17 +0000 (18:22 -0300)]
iio: adc:
cc10001: Fix the channel number mapping
commit
13415a998adb1802b5bd6bd5a336331589e866a1 upstream.
When some of the ADC channels are reserved for remote CPUs,
the scan index and the corresponding channel number doesn't
match. This leads to convesion on the incorrect channel during
triggered capture.
Fix this by using a scan index to channel mapping encoded
in the iio_chan_spec for this purpose while starting conversion
on a particular ADC channel in trigger handler.
Also, the channel_map is not really used anywhere but in probe(), so
no need to keep track of it. Remove it from device structure.
While here, add 1 to number of channels to register timestamp channel
with the IIO core.
Fixes:
1664f6a5b0c8 ("iio: adc: Cosmic Circuits 10001 ADC driver")
Signed-off-by: Naidu Tellapati <naidu.tellapati@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ivan T. Ivanov [Fri, 17 Apr 2015 14:51:08 +0000 (17:51 +0300)]
iio: adc: spmi-vadc: Fix overflow in output value normalization
commit
937125aca00e0478c4024afe58bc620a7bbe2a93 upstream.
With 'dx' equal to 0.625V and 15 bit ADC, calculations overflow
when difference against GND is ~20% of the ADC range. Fix this.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Srinivas Pandruvada [Tue, 14 Apr 2015 21:54:18 +0000 (14:54 -0700)]
iio: pressure: hid-sensor-press: Fix modifier
commit
964e2255f1d73fc0136bc206a78a1f86bdad72a7 upstream.
Fix "null" in the raw attribute and scan elements.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Srinivas Pandruvada [Tue, 14 Apr 2015 21:53:22 +0000 (14:53 -0700)]
iio: light: hid-sensor-prox: Fix modifier
commit
c2aab3d58b96002555a3e70004f593b043830248 upstream.
Currently in_proximity_(null)_raw is getting presented as raw sysfs
attribute. Same with the scan_elements.
The modifier doesn't apply to this channel.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alban Bedel [Mon, 20 Apr 2015 11:57:18 +0000 (13:57 +0200)]
iio:st_sensors: Fix oops when probing SPI devices
commit
8e71c04f863a1754f21b27fb8ecb773d680a0a80 upstream.
In SPI mode the transfer buffer is locked with a mutex. However this
mutex is only initilized after the probe, but some transfer needs to
be done in the probe.
To fix this bug we move the mutex initialization at the beginning of
the device probe.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jacob Pan [Mon, 6 Apr 2015 18:38:20 +0000 (11:38 -0700)]
iio/axp288_adc: add missing channel info mask
commit
d0716b0ea4ce11a13477163c14b26e180922ba51 upstream.
Commit
65de7654d39c70c2b ("iio: iio: Fix iio_channel_read return if
channel havn't info") added a check for valid info masks.
This patch adds missing channel info masks for all ADC channels.
Otherwise, iio_read_channel_raw() would return -EINVAL when called
by consumer drivers.
Note that the change of _processed to _raw actually fixes an ABI abuse
in the original driver where it was used to avoid some special handling
rather than because it was correct.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Lesiak [Tue, 26 May 2015 20:40:44 +0000 (15:40 -0500)]
hwmon: (ntc_thermistor) Ensure iio channel is of type IIO_VOLTAGE
commit
adba657533bdd255f7b78bc8a324091f46b294cd upstream.
When configured via device tree, the associated iio device needs to be
measuring voltage for the conversion to resistance to be correct.
Return -EINVAL if that is not the case.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Vrabel [Tue, 19 May 2015 17:40:49 +0000 (18:40 +0100)]
xen/events: don't bind non-percpu VIRQs with percpu chip
commit
77bb3dfdc0d554befad58fdefbc41be5bc3ed38a upstream.
A non-percpu VIRQ (e.g., VIRQ_CONSOLE) may be freed on a different
VCPU than it is bound to. This can result in a race between
handle_percpu_irq() and removing the action in __free_irq() because
handle_percpu_irq() does not take desc->lock. The interrupt handler
sees a NULL action and oopses.
Only use the percpu chip/handler for per-CPU VIRQs (like VIRQ_TIMER).
# cat /proc/interrupts | grep virq
40: 87246 0 xen-percpu-virq timer0
44: 0 0 xen-percpu-virq debug0
47: 0 20995 xen-percpu-virq timer1
51: 0 0 xen-percpu-virq debug1
69: 0 0 xen-dyn-virq xen-pcpu
74: 0 0 xen-dyn-virq mce
75: 29 0 xen-dyn-virq hvc_console
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Filipe Manana [Mon, 18 May 2015 18:11:40 +0000 (19:11 +0100)]
Btrfs: fix racy system chunk allocation when setting block group ro
commit
a96295965b600f2dc6ad661c4803c86e87db3d7b upstream.
If while setting a block group read-only we end up allocating a system
chunk, through check_system_chunk(), we were not doing it while holding
the chunk mutex which is a problem if a concurrent chunk allocation is
happening, through do_chunk_alloc(), as it means both block groups can
end up using the same logical addresses and physical regions in the
device(s). So make sure we hold the chunk mutex.
Fixes:
2f0810880f08 ("btrfs: delete chunk allocation attemp when
setting block group ro")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ilya Dryomov [Mon, 11 May 2015 14:53:34 +0000 (17:53 +0300)]
Revert "libceph: clear r_req_lru_item in __unregister_linger_request()"
commit
521a04d06a729e5971cdee7f84080387ed320527 upstream.
This reverts commit
ba9d114ec5578e6e99a4dfa37ff8ae688040fd64.
.. which introduced a regression that prevented all lingering requests
requeued in kick_requests() from ever being sent to the OSDs, resulting
in a lot of missed notifies. In retrospect it's pretty obvious that
r_req_lru_item item in the case of lingering requests can be used not
only for notarget, but also for unsent linkage due to how tightly
actual map and enqueue operations are coupled in __map_request().
The assertion that was being silenced is taken care of in the previous
("libceph: request a new osdmap if lingering request maps to no osd")
commit: by always kicking homeless lingering requests we ensure that
none of them ends up on the notarget list outside of the critical
section guarded by request_mutex.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ilya Dryomov [Mon, 11 May 2015 14:53:10 +0000 (17:53 +0300)]
libceph: request a new osdmap if lingering request maps to no osd
commit
b0494532214bdfbf241e94fabab5dd46f7b82631 upstream.
This commit does two things. First, if there are any homeless
lingering requests, we now request a new osdmap even if the osdmap that
is being processed brought no changes, i.e. if a given lingering
request turned homeless in one of the previous epochs and remained
homeless in the current epoch. Not doing so leaves us with a stale
osdmap and as a result we may miss our window for reestablishing the
watch and lose notifies.
MON=1 OSD=1:
# cat linger-needmap.sh
#!/bin/bash
rbd create --size 1 test
DEV=$(rbd map test)
ceph osd out 0
rbd map dne/dne # obtain a new osdmap as a side effect (!)
sleep 1
ceph osd in 0
rbd resize --size 2 test
# rbd info test | grep size -> 2M
# blockdev --getsize $DEV -> 1M
N.B.: Not obtaining a new osdmap in between "osd out" and "osd in"
above is enough to make it miss that resize notify, but that is a
bug^Wlimitation of ceph watch/notify v1.
Second, homeless lingering requests are now kicked just like those
lingering requests whose mapping has changed. This is mainly to
recognize that a homeless lingering request makes no sense and to
preserve the invariant that a registered lingering request is not
sitting on any of r_req_lru_item lists. This spares us a WARN_ON,
which commit
ba9d114ec557 ("libceph: clear r_req_lru_item in
__unregister_linger_request()") tried to fix the _wrong_ way.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Fri, 15 May 2015 14:27:40 +0000 (16:27 +0200)]
mfd: da9052: Fix broken regulator probe
commit
e0c21530fa91f119bfca19640a67380c6b14f12a upstream.
Fix broken probe of da9052 regulators, which since commit
b3f6c73db732
("mfd: da9052-core: Fix platform-device id collision") use a
non-deterministic platform-device id to retrieve static regulator
information. Fortunately, adequate error handling was in place so probe
would simply fail with an error message.
Update the mfd-cell ids to be zero-based and use those to identify the
cells when probing the regulator devices.
Fixes:
b3f6c73db732 ("mfd: da9052-core: Fix platform-device id collision")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Miklos Szeredi [Tue, 19 May 2015 12:30:12 +0000 (14:30 +0200)]
ovl: mount read-only if workdir can't be created
commit
cc6f67bcafcb6bbbb2d1be1603dcd95125a52800 upstream.
OpenWRT folks reported that overlayfs fails to mount if upper fs is full,
because workdir can't be created. Wordir creation can fail for various
other reasons too.
There's no reason that the mount itself should fail, overlayfs can work
fine without a workdir, as long as the overlay isn't modified.
So mount it read-only and don't allow remounting read-write.
Add a couple of WARN_ON()s for the impossible case of workdir being used
despite being read-only.
Reported-by: Bastian Bittorf <bittorf@bluebottle.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Miklos Szeredi [Thu, 14 May 2015 08:04:44 +0000 (10:04 +0200)]
ovl: don't remove non-empty opaque directory
commit
d377c5eb54dd05aeb3094b7740252d19ba7791f7 upstream.
When removing an opaque directory we can't just call rmdir() to check for
emptiness, because the directory will need to be replaced with a whiteout.
The replacement is done with RENAME_EXCHANGE, which doesn't check
emptiness.
Solution is just to check emptiness by reading the directory. In the
future we could add a new rename flag to check for emptiness even for
RENAME_EXCHANGE to optimize this case.
Reported-by: Vincent Batts <vbatts@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Jordi Pujol Palomer <jordipujolp@gmail.com>
Fixes:
263b4a0fee43 ("ovl: dont replace opaque dir")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rusty Russell [Wed, 27 May 2015 01:29:26 +0000 (10:59 +0930)]
lguest: fix out-by-one error in address checking.
commit
83a35114d0e4583e6b0ca39502e68b6a92e2910c upstream.
This bug has been there since day 1; addresses in the top guest physical
page weren't considered valid. You could map that page (the check in
check_gpte() is correct), but if a guest tried to put a pagetable there
we'd check that address manually when walking it, and kill the guest.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Chinner [Thu, 28 May 2015 21:40:32 +0000 (07:40 +1000)]
xfs: xfs_iozero can return positive errno
commit
cddc116228cb9d51d3224d23ba3e61fbbc3ec3d2 upstream.
It was missed when we converted everything in XFs to use negative error
numbers, so fix it now. Bug introduced in 3.17 by commit
2451337 ("xfs: global
error sign conversion"), and should go back to stable kernels.
Thanks to Brian Foster for noticing it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Chinner [Thu, 28 May 2015 21:40:08 +0000 (07:40 +1000)]
xfs: xfs_attr_inactive leaves inconsistent attr fork state behind
commit
6dfe5a049f2d48582050339d2a6b6fda36dfd14c upstream.
xfs_attr_inactive() is supposed to clean up the attribute fork when
the inode is being freed. While it removes attribute fork extents,
it completely ignores attributes in local format, which means that
there can still be active attributes on the inode after
xfs_attr_inactive() has run.
This leads to problems with concurrent inode writeback - the in-core
inode attribute fork is removed without locking on the assumption
that nothing will be attempting to access the attribute fork after a
call to xfs_attr_inactive() because it isn't supposed to exist on
disk any more.
To fix this, make xfs_attr_inactive() completely remove all traces
of the attribute fork from the inode, regardless of it's state.
Further, also remove the in-core attribute fork structure safely so
that there is nothing further that needs to be done by callers to
clean up the attribute fork. This means we can remove the in-core
and on-disk attribute forks atomically.
Also, on error simply remove the in-memory attribute fork. There's
nothing that can be done with it once we have failed to remove the
on-disk attribute fork, so we may as well just blow it away here
anyway.
Reported-by: Waiman Long <waiman.long@hp.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bob Copeland [Thu, 28 May 2015 22:44:35 +0000 (15:44 -0700)]
omfs: fix sign confusion for bitmap loop counter
commit
c0345ee57d461343586b5e1e2f9c3c3766d07fe6 upstream.
The count variable is used to iterate down to (below) zero from the size
of the bitmap and handle the one-filling the remainder of the last
partial bitmap block. The loop conditional expects count to be signed
in order to detect when the final block is processed, after which count
goes negative.
Unfortunately, a recent change made this unsigned along with some other
related fields. The result of is this is that during mount,
omfs_get_imap will overrun the bitmap array and corrupt memory unless
number of blocks happens to be a multiple of 8 * blocksize.
Fix by changing count back to signed: it is guaranteed to fit in an s32
without overflow due to an enforced limit on the number of blocks in the
filesystem.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sasha Levin [Thu, 28 May 2015 22:44:29 +0000 (15:44 -0700)]
fs, omfs: add NULL terminator in the end up the token list
commit
dcbff39da3d815f08750552fdd04f96b51751129 upstream.
match_token() expects a NULL terminator at the end of the token list so
that it would know where to stop. Not having one causes it to overrun
to invalid memory.
In practice, passing a mount option that omfs didn't recognize would
sometimes panic the system.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
John Stultz [Fri, 8 May 2015 20:47:23 +0000 (13:47 -0700)]
ktime: Fix ktime_divns to do signed division
commit
f7bcb70ebae0dcdb5a2d859b09e4465784d99029 upstream.
It was noted that the 32bit implementation of ktime_divns()
was doing unsigned division and didn't properly handle
negative values.
And when a ktime helper was changed to utilize
ktime_divns, it caused a regression on some IR blasters.
See the following bugzilla for details:
https://bugzilla.redhat.com/show_bug.cgi?id=
1200353
This patch fixes the problem in ktime_divns by checking
and preserving the sign bit, and then reapplying it if
appropriate after the division, it also changes the return
type to a s64 to make it more obvious this is expected.
Nicolas also pointed out that negative dividers would
cause infinite loops on 32bit systems, negative dividers
is unlikely for users of this function, but out of caution
this patch adds checks for negative dividers for both
32-bit (BUG_ON) and 64-bit(WARN_ON) versions to make sure
no such use cases creep in.
[ tglx: Hand an u64 to do_div() to avoid the compiler warning ]
Fixes:
166afb64511e 'ktime: Sanitize ktime_to_us/ms conversion'
Reported-and-tested-by: Trevor Cordes <trevor@tecnopolis.ca>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Link: http://lkml.kernel.org/r/1431118043-23452-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liang Li [Wed, 20 May 2015 20:41:25 +0000 (04:41 +0800)]
kvm/fpu: Enable eager restore kvm FPU for MPX
commit
c447e76b4cabb49ddae8e49c5758f031f35d55fb upstream.
The MPX feature requires eager KVM FPU restore support. We have verified
that MPX cannot work correctly with the current lazy KVM FPU restore
mechanism. Eager KVM FPU restore should be enabled if the MPX feature is
exposed to VM.
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Signed-off-by: Liang Li <liang.z.li@intel.com>
[Also activate the FPU on AMD processors. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xiao Guangrong [Mon, 11 May 2015 14:55:21 +0000 (22:55 +0800)]
KVM: MMU: fix SMAP virtualization
commit
0be0226f07d14b153a5eedf2bb86e1eb7dcefab5 upstream.
KVM may turn a user page to a kernel page when kernel writes a readonly
user page if CR0.WP = 1. This shadow page entry will be reused after
SMAP is enabled so that kernel is allowed to access this user page
Fix it by setting SMAP && !CR0.WP into shadow page's role and reset mmu
once CR4.SMAP is updated
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrea Arcangeli [Fri, 8 May 2015 12:32:56 +0000 (14:32 +0200)]
kvm: fix crash in kvm_vcpu_reload_apic_access_page
commit
e8fd5e9e9984675f45b9a5485909c143fbde248f upstream.
memslot->userfault_addr is set by the kernel with a mmap executed
from the kernel but the userland can still munmap it and lead to the
below oops after memslot->userfault_addr points to a host virtual
address that has no vma or mapping.
[ 327.538306] BUG: unable to handle kernel paging request at
fffffffffffffffe
[ 327.538407] IP: [<
ffffffff811a7b55>] put_page+0x5/0x50
[ 327.538474] PGD
1a01067 PUD
1a03067 PMD 0
[ 327.538529] Oops: 0000 [#1] SMP
[ 327.538574] Modules linked in: macvtap macvlan xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT iptable_filter ip_tables tun bridge stp llc rpcsec_gss_krb5 nfsv4 dns_resolver nfs fscache xprtrdma ib_isert iscsi_target_mod ib_iser libiscsi scsi_transport_iscsi ib_srpt target_core_mod ib_srp scsi_transport_srp scsi_tgt ib_ipoib rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm ipmi_devintf iTCO_wdt iTCO_vendor_support intel_powerclamp coretemp dcdbas intel_rapl kvm_intel kvm crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd pcspkr sb_edac edac_core ipmi_si ipmi_msghandler acpi_pad wmi acpi_power_meter lpc_ich mfd_core mei_me
[ 327.539488] mei shpchp nfsd auth_rpcgss nfs_acl lockd grace sunrpc mlx4_ib ib_sa ib_mad ib_core mlx4_en vxlan ib_addr ip_tunnel xfs libcrc32c sd_mod crc_t10dif crct10dif_common crc32c_intel mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit drm_kms_helper ttm drm ahci i2c_core libahci mlx4_core libata tg3 ptp pps_core megaraid_sas ntb dm_mirror dm_region_hash dm_log dm_mod
[ 327.539956] CPU: 3 PID: 3161 Comm: qemu-kvm Not tainted 3.10.0-240.el7.userfault19.
4ca4011.x86_64.debug #1
[ 327.540045] Hardware name: Dell Inc. PowerEdge R420/0CN7CM, BIOS 2.1.2 01/20/2014
[ 327.540115] task:
ffff8803280ccf00 ti:
ffff880317c58000 task.ti:
ffff880317c58000
[ 327.540184] RIP: 0010:[<
ffffffff811a7b55>] [<
ffffffff811a7b55>] put_page+0x5/0x50
[ 327.540261] RSP: 0018:
ffff880317c5bcf8 EFLAGS:
00010246
[ 327.540313] RAX:
00057ffffffff000 RBX:
ffff880616a20000 RCX:
0000000000000000
[ 327.540379] RDX:
0000000000002014 RSI:
00057ffffffff000 RDI:
fffffffffffffffe
[ 327.540445] RBP:
ffff880317c5bd10 R08:
0000000000000103 R09:
0000000000000000
[ 327.540511] R10:
0000000000000000 R11:
0000000000000000 R12:
fffffffffffffffe
[ 327.540576] R13:
0000000000000000 R14:
ffff880317c5bd70 R15:
ffff880317c5bd50
[ 327.540643] FS:
00007fd230b7f700(0000) GS:
ffff880630800000(0000) knlGS:
0000000000000000
[ 327.540717] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 327.540771] CR2:
fffffffffffffffe CR3:
000000062a2c3000 CR4:
00000000000427e0
[ 327.540837] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[ 327.540904] DR3:
0000000000000000 DR6:
00000000ffff0ff0 DR7:
0000000000000400
[ 327.540974] Stack:
[ 327.541008]
ffffffffa05d6d0c ffff880616a20000 0000000000000000 ffff880317c5bdc0
[ 327.541093]
ffffffffa05ddaa2 0000000000000000 00000000002191bf 00000042f3feab2d
[ 327.541177]
00000042f3feab2d 0000000000000002 0000000000000001 0321000000000000
[ 327.541261] Call Trace:
[ 327.541321] [<
ffffffffa05d6d0c>] ? kvm_vcpu_reload_apic_access_page+0x6c/0x80 [kvm]
[ 327.543615] [<
ffffffffa05ddaa2>] vcpu_enter_guest+0x3f2/0x10f0 [kvm]
[ 327.545918] [<
ffffffffa05e2f10>] kvm_arch_vcpu_ioctl_run+0x2b0/0x5a0 [kvm]
[ 327.548211] [<
ffffffffa05e2d02>] ? kvm_arch_vcpu_ioctl_run+0xa2/0x5a0 [kvm]
[ 327.550500] [<
ffffffffa05ca845>] kvm_vcpu_ioctl+0x2b5/0x680 [kvm]
[ 327.552768] [<
ffffffff810b8d12>] ? creds_are_invalid.part.1+0x12/0x50
[ 327.555069] [<
ffffffff810b8d71>] ? creds_are_invalid+0x21/0x30
[ 327.557373] [<
ffffffff812d6066>] ? inode_has_perm.isra.49.constprop.65+0x26/0x80
[ 327.559663] [<
ffffffff8122d985>] do_vfs_ioctl+0x305/0x530
[ 327.561917] [<
ffffffff8122dc51>] SyS_ioctl+0xa1/0xc0
[ 327.564185] [<
ffffffff816de829>] system_call_fastpath+0x16/0x1b
[ 327.566480] Code: 0b 31 f6 4c 89 e7 e8 4b 7f ff ff 0f 0b e8 24 fd ff ff e9 a9 fd ff ff 66 66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 66 66 66 66 90 <48> f7 07 00 c0 00 00 55 48 89 e5 75 2a 8b 47 1c 85 c0 74 1e f0
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xiao Guangrong [Thu, 7 May 2015 08:20:15 +0000 (16:20 +0800)]
KVM: MMU: fix smap permission check
commit
7cbeed9bce7580479bb97457dad220cb3594b875 upstream.
Current permission check assumes that RSVD bit in PFEC is always zero,
however, it is not true since MMIO #PF will use it to quickly identify
MMIO access
Fix it by clearing the bit if walking guest page table is needed
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Bonzini [Thu, 2 Apr 2015 09:04:05 +0000 (11:04 +0200)]
KVM: MMU: fix CR4.SMEP=1, CR0.WP=0 with shadow pages
commit
898761158be7682082955e3efa4ad24725305fc7 upstream.
smep_andnot_wp is initialized in kvm_init_shadow_mmu and shadow pages
should not be reused for different values of it. Thus, it has to be
added to the mask in kvm_mmu_pte_write.
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ingo Molnar [Wed, 20 May 2015 09:45:30 +0000 (11:45 +0200)]
x86/fpu: Disable XSAVES* support for now
commit
e88221c50cadade0eb4f7f149f4967d760212695 upstream.
The kernel's handling of 'compacted' xsave state layout is buggy:
http://marc.info/?l=linux-kernel&m=
142967852317199
I don't have such a system, and the description there is vague, but
from extrapolation I guess that there were two kinds of bugs
observed:
- boot crashes, due to size calculations being wrong and the dynamic
allocation allocating a too small xstate area. (This is now fixed
in the new FPU code - but still present in stable kernels.)
- FPU state corruption and ABI breakage: if signal handlers try to
change the FPU state in standard format, which then the kernel
tries to restore in the compacted format.
These breakages are scary, but they only occur on a small number of
systems that have XSAVES* CPU support. Yet we have had XSAVES support
in the upstream kernel for a large number of stable kernel releases,
and the fixes are involved and unproven.
So do the safe resolution first: disable XSAVES* support and only
use the standard xstate format. This makes the code work and is
easy to backport.
On top of this we can work on enabling (and testing!) proper
compacted format support, without backporting pressure, on top of the
new, cleaned up FPU code.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Borislav Petkov [Mon, 18 May 2015 08:07:17 +0000 (10:07 +0200)]
x86/mce: Fix MCE severity messages
commit
17fea54bf0ab34fa09a06bbde2f58ed7bbdf9299 upstream.
Derek noticed that a critical MCE gets reported with the wrong
error type description:
[Hardware Error]: CPU 34: Machine Check Exception: 5 Bank 9:
f200003f000100b0
[Hardware Error]: RIP !INEXACT! 10:<
ffffffff812e14c1> {intel_idle+0xb1/0x170}
[Hardware Error]: TSC
49587b8e321cb
[Hardware Error]: PROCESSOR 0:306e4 TIME
1431561296 SOCKET 1 APIC 29
[Hardware Error]: Some CPUs didn't answer in synchronization
[Hardware Error]: Machine check: Invalid
^^^^^^^
The last line with 'Invalid' should have printed the high level
MCE error type description we get from mce_severity, i.e.
something like:
[Hardware Error]: Machine check: Action required: data load error in a user process
this happens due to the fact that mce_no_way_out() iterates over
all MCA banks and possibly overwrites the @msg argument which is
used in the panic printing later.
Change behavior to take the message of only and the (last)
critical MCE it detects.
Reported-by: Derek <denc716@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1431936437-25286-3-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Bonzini [Wed, 20 May 2015 09:33:43 +0000 (11:33 +0200)]
Revert "KVM: x86: drop fpu_activate hook"
commit
0fdd74f7784b5cdff7075736992bbb149b1ae49c upstream.
This reverts commit
4473b570a7ebb502f63f292ccfba7df622e5fdd3. We'll
use the hook again.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon [Fri, 8 May 2015 16:44:22 +0000 (17:44 +0100)]
iommu/arm-smmu: Fix sign-extension of upstream bus addresses at stage 1
commit
5dc5616ee850eaba055bb469a6c4a471d489140e upstream.
Stage 1 translation is controlled by two sets of page tables (TTBR0 and
TTBR1) which grow up and down from zero respectively in the ARMv8
translation regime. For the SMMU, we only care about TTBR0 and, in the
case of a 48-bit virtual space, we expect to map virtual addresses 0x0
through to 0xffff_ffff_ffff.
Given that some masters may be incapable of emitting virtual addresses
targetting TTBR1 (e.g. because they sit on a 48-bit bus), the SMMU
architecture allows bit 47 to be sign-extended, halving the virtual
range of TTBR0 but allowing TTBR1 to be used. This is controlled by the
SEP field in TTBCR2.
The SMMU driver incorrectly enables this sign-extension feature, which
causes problems when userspace addresses are programmed into a master
device with the SMMU expecting to map the incoming transactions via
TTBR0; if the top bit of address is set, we will instead get a
translation fault since TTBR1 walks are disabled in the TTBCR.
This patch fixes the issue by disabling sign-extension of a fixed
virtual address bit and instead basing the behaviour on the upstream bus
size: the incoming address is zero extended unless the upstream bus is
only 49 bits wide, in which case bit 48 is used as the sign bit and is
replicated to the upper bits.
Reported-by: Varun Sethi <varun.sethi@freescale.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oded Gabbay [Thu, 16 Apr 2015 14:08:44 +0000 (17:08 +0300)]
iommu/amd: Fix bug in put_pasid_state_wait
commit
1bf1b431d98d7e5b5419876d4c219469e60693e1 upstream.
This patch fixes a bug in put_pasid_state_wait that appeared in kernel 4.0
The bug is that pasid_state->count wasn't decremented before entering the
wait_event. Thus, the condition in wait_event will never be true.
The fix is to decrement (atomically) the pasid_state->count before the
wait_event.
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric W. Biederman [Thu, 2 Apr 2015 21:35:48 +0000 (16:35 -0500)]
fs_pin: Allow for the possibility that m_list or s_list go unused.
commit
820f9f147dcce2602eefd9b575bbbd9ea14f0953 upstream.
This is needed to support lazily umounting locked mounts. Because the
entire unmounted subtree needs to stay together until there are no
users with references to any part of the subtree.
To support this guarantee that the fs_pin m_list and s_list nodes
are initialized by initializing them in init_fs_pin allowing
for the possibility that pin_insert_group does not touch them.
Further use hlist_del_init in pin_remove so that there is
a hlist_unhashed test before the list we attempt to update
the previous list item.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric W. Biederman [Wed, 7 Jan 2015 20:28:26 +0000 (14:28 -0600)]
mnt: Fail collect_mounts when applied to unmounted mounts
commit
cd4a40174b71acd021877341684d8bb1dc8ea4ae upstream.
The only users of collect_mounts are in audit_tree.c
In audit_trim_trees and audit_add_tree_rule the path passed into
collect_mounts is generated from kern_path passed an audit_tree
pathname which is guaranteed to be an absolute path. In those cases
collect_mounts is obviously intended to work on mounted paths and
if a race results in paths that are unmounted when collect_mounts
it is reasonable to fail early.
The paths passed into audit_tag_tree don't have the absolute path
check. But are used to play with fsnotify and otherwise interact with
the audit_trees, so again operating only on mounted paths appears
reasonable.
Avoid having to worry about what happens when we try and audit
unmounted filesystems by restricting collect_mounts to mounts
that appear in the mount tree.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sun, 17 May 2015 16:55:21 +0000 (09:55 -0700)]
Linux 4.0.4
Lv Zheng [Mon, 13 Apr 2015 03:48:52 +0000 (11:48 +0800)]
ACPICA: Utilities: Cleanup to remove useless ACPI_PRINTF/FORMAT_xxx helpers.
commit
1d0a0b2f6df2bf2643fadc990eb143361eca6ada upstream.
ACPICA commit
b60612373a4ef63b64a57c124576d7ddb6d8efb6
For physical addresses, since the address may exceed 32-bit address range
after calculation, we should use 0x%8.8X%8.8X instead of ACPI_PRINTF_UINT
and ACPI_FORMAT_UINT64() instead of
ACPI_FORMAT_NATIVE_UINT()/ACPI_FORMAT_TO_UINT().
This patch also removes above replaced macros as there are no users.
This is a preparation to switch acpi_physical_address to 64-bit on 32-bit
kernel builds.
Link: https://github.com/acpica/acpica/commit/b6061237
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lv Zheng [Mon, 13 Apr 2015 03:48:46 +0000 (11:48 +0800)]
ACPICA: Utilities: Cleanup to convert physical address printing formats.
commit
cc2080b0e5a7c6c33ef5e9ffccbc2b8f6f861393 upstream.
ACPICA commit
7f06739db43a85083a70371c14141008f20b2198
For physical addresses, since the address may exceed 32-bit address range
after calculation, we should use %8.8X%8.8X (see ACPI_FORMAT_UINT64()) to
convert the %p formats.
This is a preparation to switch acpi_physical_address to 64-bit on 32-bit
kernel builds.
Link: https://github.com/acpica/acpica/commit/7f06739d
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lv Zheng [Mon, 13 Apr 2015 03:48:37 +0000 (11:48 +0800)]
ACPICA: Utilities: Cleanup to enforce ACPI_PHYSADDR_TO_PTR()/ACPI_PTR_TO_PHYSADDR().
commit
6d3fd3cc33d50e4c0d0c0bd172de02caaec3127c upstream.
ACPICA commit
154f6d074dd38d6ebc0467ad454454e6c5c9ecdf
There are code pieces converting pointers using "(acpi_physical_address) x"
or "ACPI_CAST_PTR (t, x)" formats, this patch cleans up them.
Known issues:
1. Cleanup of "(ACPI_PHYSICAL_ADDRRESS) x" for a table field
For the conversions around the table fields, it is better to fix it with
alignment also fixed. So this patch doesn't modify such code. There
should be no functional problem by leaving them unchanged.
Link: https://github.com/acpica/acpica/commit/154f6d07
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lv Zheng [Mon, 13 Apr 2015 03:48:18 +0000 (11:48 +0800)]
ACPICA: Tables: Change acpi_find_root_pointer() to use acpi_physical_address.
commit
f254e3c57b9d952e987502aefa0804c177dd2503 upstream.
ACPICA commit
7d9fd64397d7c38899d3dc497525f6e6b044e0e3
OSPMs like Linux expect an acpi_physical_address returning value from
acpi_find_root_pointer(). This triggers warnings if sizeof (acpi_size) doesn't
equal to sizeof (acpi_physical_address):
drivers/acpi/osl.c:275:3: warning: passing argument 1 of 'acpi_find_root_pointer' from incompatible pointer type [enabled by default]
In file included from include/acpi/acpi.h:64:0,
from include/linux/acpi.h:36,
from drivers/acpi/osl.c:41:
include/acpi/acpixf.h:433:1: note: expected 'acpi_size *' but argument is of type 'acpi_physical_address *'
This patch corrects acpi_find_root_pointer().
Link: https://github.com/acpica/acpica/commit/7d9fd643
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro [Fri, 3 Apr 2015 19:23:17 +0000 (15:23 -0400)]
coredump: accept any write method
commit
86cc05840a0da1afcb6b8151b53f3b606457c91b upstream.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Khoroshilov [Fri, 17 Apr 2015 23:53:25 +0000 (02:53 +0300)]
sound/oss: fix deadlock in sequencer_ioctl(SNDCTL_SEQ_OUTOFBAND)
commit
bc26d4d06e337ade069f33d3f4377593b24e6e36 upstream.
A deadlock can be initiated by userspace via ioctl(SNDCTL_SEQ_OUTOFBAND)
on /dev/sequencer with TMR_ECHO midi event.
In this case the control flow is:
sound_ioctl()
-> case SND_DEV_SEQ:
case SND_DEV_SEQ2:
sequencer_ioctl()
-> case SNDCTL_SEQ_OUTOFBAND:
spin_lock_irqsave(&lock,flags);
play_event();
-> case EV_TIMING:
seq_timing_event()
-> case TMR_ECHO:
seq_copy_to_input()
-> spin_lock_irqsave(&lock,flags);
It seems that spin_lock_irqsave() around play_event() is not necessary,
because the only other call location in seq_startplay() makes the call
without acquiring spinlock.
So, the patch just removes spinlocks around play_event().
By the way, it removes unreachable code in seq_timing_event(),
since (seq_mode == SEQ_2) case is handled in the beginning.
Compile tested only.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Rutland [Fri, 6 Mar 2015 11:08:30 +0000 (12:08 +0100)]
ARM: 8307/1: psci: move psci firmware calls out of line
commit
c097877319ab61dd045b6497953b4e3df8f2bb44 upstream.
arm64 builds with GCC 5 have caused the __asmeq assertions in the PSCI
calling code to fire, so move the ARM PSCI calls out of line into their
own assembly file for consistency and to safeguard against the same
issue occuring with the 32-bit toolchain.
[will: brought into line with arm64 implementation]
Reported-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takeshi Kihara [Wed, 29 Apr 2015 17:03:51 +0000 (02:03 +0900)]
mmc: sh_mmcif: Fix timeout value for command request
commit
bad4371d87d1d1ed1aecd9c9cc21c41ac3f289c8 upstream.
f9fd54f22e ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout")
changed the timeout value from 1000 jiffies to 1s. In the case where
HZ is 1000 the values are the same. However, for smaller HZ values the
timeout is now smaller, 1s instead of 10s in the case of HZ=100.
Since the timeout occurs in spite of a normal data transfer a timeout of
10s seems more appropriate. This restores the previous timeout in the
case where HZ=100 and results in an increase over the previous timeout
for larger values of HZ.
Fixes:
f9fd54f22e ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[horms: rewrote changelog to refer to HZ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Grygorii Strashko [Thu, 23 Apr 2015 10:43:43 +0000 (13:43 +0300)]
mmc: core: add missing pm event in mmc_pm_notify to fix hib restore
commit
184af16b09360d6273fd6160e6ff7f8e2482ef23 upstream.
The PM_RESTORE_PREPARE is not handled now in mmc_pm_notify(),
as result mmc_rescan() could be scheduled and executed at
late hibernation restore stages when MMC device is suspended
already - which, in turn, will lead to system crash on TI dra7-evm board:
WARNING: CPU: 0 PID: 3188 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x258/0x374()
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in User mode during Functional access
Hence, add missed PM_RESTORE_PREPARE PM event in mmc_pm_notify().
Fixes:
4c2ef25fe0b8 (mmc: fix all hangs related to mmc/sd card...)
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chuanxiao Dong [Tue, 12 Aug 2014 04:01:30 +0000 (12:01 +0800)]
mmc: card: Don't access RPMB partitions for normal read/write
commit
4e93b9a6abc0d028daf3c8a00cb77b679d8a4df4 upstream.
During kernel boot, it will try to read some logical sectors
of each block device node for the possible partition table.
But since RPMB partition is special and can not be accessed
by normal eMMC read / write CMDs, it will cause below error
messages during kernel boot:
...
mmc0: Got data interrupt 0x00000002 even though no data operation was in progress.
mmcblk0rpmb: error -110 transferring data, sector 0, nr 32, cmd response 0x900, card status 0xb00
mmcblk0rpmb: retrying using single block read
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
end_request: I/O error, dev mmcblk0rpmb, sector 0
Buffer I/O error on device mmcblk0rpmb, logical block 0
end_request: I/O error, dev mmcblk0rpmb, sector 8
Buffer I/O error on device mmcblk0rpmb, logical block 1
end_request: I/O error, dev mmcblk0rpmb, sector 16
Buffer I/O error on device mmcblk0rpmb, logical block 2
end_request: I/O error, dev mmcblk0rpmb, sector 24
Buffer I/O error on device mmcblk0rpmb, logical block 3
...
This patch will discard the access request in eMMC queue if
it is RPMB partition access request. By this way, it avoids
trigger above error messages.
Fixes:
090d25fe224c ("mmc: core: Expose access to RPMB partition")
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Tested-by: Michael Shigorin <mike@altlinux.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Doug Anderson [Fri, 1 May 2015 16:01:27 +0000 (09:01 -0700)]
pinctrl: Don't just pretend to protect pinctrl_maps, do it for real
commit
c5272a28566b00cce79127ad382406e0a8650690 upstream.
Way back, when the world was a simpler place and there was no war, no
evil, and no kernel bugs, there was just a single pinctrl lock. That
was how the world was when (
57291ce pinctrl: core device tree mapping
table parsing support) was written. In that case, there were
instances where the pinctrl mutex was already held when
pinctrl_register_map() was called, hence a "locked" parameter was
passed to the function to indicate that the mutex was already locked
(so we shouldn't lock it again).
A few years ago in (
42fed7b pinctrl: move subsystem mutex to
pinctrl_dev struct), we switched to a separate pinctrl_maps_mutex.
...but (oops) we forgot to re-think about the whole "locked" parameter
for pinctrl_register_map(). Basically the "locked" parameter appears
to still refer to whether the bigger pinctrl_dev mutex is locked, but
we're using it to skip locks of our (now separate) pinctrl_maps_mutex.
That's kind of a bad thing(TM). Probably nobody noticed because most
of the calls to pinctrl_register_map happen at boot time and we've got
synchronous device probing. ...and even cases where we're
asynchronous don't end up actually hitting the race too often. ...but
after banging my head against the wall for a bug that reproduced 1 out
of 1000 reboots and lots of looking through kgdb, I finally noticed
this.
Anyway, we can now safely remove the "locked" parameter and go back to
a war-free, evil-free, and kernel-bug-free world.
Fixes:
42fed7ba44e4 ("pinctrl: move subsystem mutex to pinctrl_dev struct")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian König [Thu, 7 May 2015 13:19:24 +0000 (15:19 +0200)]
drm/radeon: more strictly validate the UVD codec
commit
d52cdfa4a0c6406bbfb33206341eaf1fb1555994 upstream.
MPEG 2/4 are only supported since UVD3.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian König [Thu, 7 May 2015 13:19:23 +0000 (15:19 +0200)]
drm/radeon: make UVD handle checking more strict
commit
a1b403da70e038ca6c6c6fe434d1d873546873a3 upstream.
Invalid messages can crash the hw otherwise.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian König [Thu, 7 May 2015 13:19:22 +0000 (15:19 +0200)]
drm/radeon: make VCE handle check more strict
commit
29c63fe22a17c64e54016040cd882481bd45ee5a upstream.
Invalid handles can crash the hw.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
monk.liu [Tue, 5 May 2015 07:24:17 +0000 (09:24 +0200)]
drm/radeon: fix userptr BO unpin bug v3
commit
db12973cd581d4e79f4aadd0960948f268d15af7 upstream.
Fixing a memory leak with userptrs.
v2: clean up the loop, use an iterator instead
v3: remove unused variable
Signed-off-by: monk.liu <monk.liu@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Deucher [Mon, 4 May 2015 18:35:01 +0000 (14:35 -0400)]
drm/radeon: don't setup audio on asics that don't support it
commit
d73a824acc705571c0f47596326d7967fba9a1d9 upstream.
bug: https://bugzilla.kernel.org/show_bug.cgi?id=97701
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Tested-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian König [Fri, 1 May 2015 10:34:12 +0000 (12:34 +0200)]
drm/radeon: disable semaphores for UVD V1 (v2)
commit
013ead48a843442e63b9426e3bd5df18ca5d054a upstream.
Hardware doesn't seem to work correctly, just block userspace in this case.
v2: add missing defines
Bugs: https://bugs.freedesktop.org/show_bug.cgi?id=85320
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xihan Zhang [Tue, 28 Apr 2015 15:48:40 +0000 (23:48 +0800)]
drm/amdkfd: Initialize sdma vm when creating sdma queue
commit
79b066bd76d501cfe8328142153da301f5ca11d1 upstream.
This patch fixes a bug where sdma vm wasn't initialized when
an sdma queue was created in HWS mode.
This caused GPUVM faults to appear on dmesg and it is one of the
causes that SDMA queues are not working.
Signed-off-by: Xihan Zhang <xihan.zhang@amd.com>
Reviewed-by: Ben Goz <ben.goz@amd.comt>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oded Gabbay [Tue, 14 Apr 2015 11:13:18 +0000 (14:13 +0300)]
drm/amdkfd: allow unregister process with queues
commit
1e5ec956a057585adaa1365615c82810b2f5356f upstream.
Sometimes we might unregister process that have queues, because we couldn't
preempt the queues. Until now we blocked it with BUG_ON but instead just
print it as debug.
Reviewed-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jani Nikula [Tue, 5 May 2015 13:32:12 +0000 (16:32 +0300)]
drm/i915/dp: there is no audio on port A
commit
9fcb1704d1d51b12e2f03c78bca013d0cbbb7c98 upstream.
The eDP port A register on PCH split platforms has a slightly different
register layout from the other ports, with bit 6 being either alternate
scrambler reset or reserved, depending on the generation. Our
misinterpretation of the bit as audio has lead to warning.
Fix this by not enabling audio on port A, since none of our platforms
support audio on port A anyway.
v2: DDI doesn't have audio on port A either (Sivakumar Thulasimani)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89958
Reported-and-tested-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lukas Wunner [Mon, 4 May 2015 13:06:49 +0000 (15:06 +0200)]
drm/i915: Add missing MacBook Pro models with dual channel LVDS
commit
3916e3fd81021fb795bfbdb17f375b6b3685bced upstream.
Single channel LVDS maxes out at 112 MHz. The 15" pre-retina models
shipped with 1440x900 (106 MHz) by default or 1680x1050 (119 MHz)
as a BTO option, both versions used dual channel LVDS even though
the smaller one would have fit into a single channel.
Notes:
Bug report showing that the MacBookPro8,2 with 1440x900 uses dual
channel LVDS (this lead to it being hardcoded in intel_lvds.c by
Daniel Vetter with commit
618563e3945b9d0864154bab3c607865b557cecc):
https://bugzilla.kernel.org/show_bug.cgi?id=42842
If i915.lvds_channel_mode=2 is missing even though the machine needs
it, every other vertical line is white and consequently, only the left
half of the screen is visible (verified by myself on a MacBookPro9,1).
Forum posting concerning a MacBookPro6,2 with 1440x900, author is
using i915.lvds_channel_mode=2 on the kernel command line, proving
that the machine uses dual channels:
https://bbs.archlinux.org/viewtopic.php?id=185770
Chi Mei N154C6-L04 with 1440x900 is a replacement panel for all
MacBook Pro "A1286" models, and that model number encompasses the
MacBookPro6,2 / 8,2 / 9,1. Page 17 of the panel's datasheet shows it's
driven with dual channel LVDS:
http://www.ebay.com/itm/-/
400690878560
http://www.everymac.com/ultimate-mac-lookup/?search_keywords=A1286
http://www.taopanel.com/chimei/datasheet/N154C6-L04.pdf
Those three 15" models, MacBookPro6,2 / 8,2 / 9,1, are the only ones
with i915 graphics and dual channel LVDS, so that list should be
complete. And the 8,2 is already in intel_lvds.c.
Possible motivation to use dual channel LVDS even on the 1440x900
models: Reduce the number of different parts, i.e. use identical logic
boards and display cabling on both versions and the only differing
component is the panel.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
[Jani: included notes in the commit message for posterity]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lukas Wunner [Sun, 12 Apr 2015 19:10:35 +0000 (21:10 +0200)]
drm/i915: Assume dual channel LVDS if pixel clock necessitates it
commit
6f317cfe42c9d8a7c9c1a327d2f1bcc517a3cd91 upstream.
Single channel LVDS maxes out at 112 MHz, anything above must be dual
channel. This avoids the need to specify i915.lvds_channel_mode=2 on
all 17" MacBook Pro models with i915 graphics since they had 1920x1200
(193 MHz), plus those 15" pre-retina models which had a resolution
of 1680x1050 (119 MHz) as a BTO option.
Source for 112 MHz limit of single channel LVDS is section 2.3 of:
https://01.org/linuxgraphics/sites/default/files/documentation/ivb_ihd_os_vol3_part4.pdf
v2: Avoid hardcoding 17" models by assuming dual channel LVDS if the
resolution necessitates it, suggested by Jani Nikula.
v3: Fix typo, thanks Joonas Lahtinen.
v4: Split commit in two, suggested by Ville Syrjälä.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Jani: included spec reference into the commit message]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>