OSDN Git Service
Robert Marko [Tue, 22 Sep 2020 10:16:31 +0000 (12:16 +0200)]
net: mdio-ipq4019: change defines to upper case
In the commit adding the IPQ4019 MDIO driver, defines for timeout and sleep partially used lower case.
Lets change it to upper case in line with the rest of driver defines.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 24 Sep 2020 00:35:26 +0000 (17:35 -0700)]
Merge branch 'Introduce-mbox-tracepoints-for-Octeontx2'
Subbaraya Sundeep says:
====================
Introduce mbox tracepoints for Octeontx2
This patchset adds tracepoints support for mailbox.
In Octeontx2, PFs and VFs need to communicate with AF
for allocating and freeing resources. Once all the
configuration is done by AF for a PF/VF then packet I/O
can happen on PF/VF queues. When an interface
is brought up many mailbox messages are sent
to AF for initializing queues. Say a VF is brought up
then each message is sent to PF and PF forwards to
AF and response also traverses from AF to PF and then VF.
To aid debugging, tracepoints are added at places where
messages are allocated, sent and message interrupts.
Below is the trace of one of the messages from VF to AF
and AF response back to VF:
~ # echo 1 > /sys/kernel/tracing/events/rvu/enable
~ # ifconfig eth20 up
[ 279.379559] eth20 NIC Link is UP 10000 Mbps Full duplex
~ # cat /sys/kernel/tracing/trace
ifconfig-171 [000] .... 275.753345: otx2_msg_alloc: [0002:02:00.1] msg:(0x400) size:40
ifconfig-171 [000] ...1 275.753347: otx2_msg_send: [0002:02:00.1] sent 1 msg(s) of size:48
<idle>-0 [001] dNh1 275.753356: otx2_msg_interrupt: [0002:02:00.0] mbox interrupt VF(s) to PF (0x1)
kworker/u9:1-90 [001] ...1 275.753364: otx2_msg_send: [0002:02:00.0] sent 1 msg(s) of size:48
kworker/u9:1-90 [001] d.h. 275.753367: otx2_msg_interrupt: [0002:01:00.0] mbox interrupt PF(s) to AF (0x2)
kworker/u9:2-167 [002] .... 275.753535: otx2_msg_process: [0002:01:00.0] msg:(0x400) error:0
kworker/u9:2-167 [002] ...1 275.753537: otx2_msg_send: [0002:01:00.0] sent 1 msg(s) of size:32
<idle>-0 [003] d.h1 275.753543: otx2_msg_interrupt: [0002:02:00.0] mbox interrupt AF to PF (0x1)
<idle>-0 [001] d.h2 275.754376: otx2_msg_interrupt: [0002:02:00.1] mbox interrupt PF to VF (0x1)
v3 changes:
Removed EXPORT_TRACEPOINT_SYMBOLS of otx2_msg_send and otx2_msg_check
since they are called locally only
v2 changes:
Removed otx2_msg_err tracepoint since it is similar to devlink_hwerr
and it will be used instead when devlink supported is added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Subbaraya Sundeep [Tue, 22 Sep 2020 02:57:05 +0000 (08:27 +0530)]
octeontx2-pf: Add tracepoints for PF/VF mailbox
With tracepoints support present in the mailbox
code this patch adds tracepoints in PF and VF drivers
at places where mailbox messages are allocated,
sent and at message interrupts.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subbaraya Sundeep [Tue, 22 Sep 2020 02:57:04 +0000 (08:27 +0530)]
octeontx2-af: Introduce tracepoints for mailbox
Added tracepoints in mailbox code so that
the mailbox operations like message allocation,
sending message and message interrupts are traced.
Also the mailbox errors occurred like timeout
or wrong responses are traced.
These will help in debugging mailbox issues.
Here's an example output showing one of the mailbox
messages sent by PF to AF and AF responding to it:
~# mount -t tracefs none /sys/kernel/tracing/
~# echo 1 > /sys/kernel/tracing/events/rvu/enable
~# ifconfig eth0 up
~# cat /sys/kernel/tracing/trace
~# cat /sys/kernel/tracing/trace
tracer: nop
_-----=> irqs-off
/ _----=> need-resched
| / _---=> hardirq/softirq
|| / _--=> preempt-depth
||| / delay
TASK-PID CPU# |||| TIMESTAMP FUNCTION
| | | |||| | |
ifconfig-2382 [002] .... 756.161892: otx2_msg_alloc: [0002:02:00.0] msg:(0x400) size:40
ifconfig-2382 [002] ...1 756.161895: otx2_msg_send: [0002:02:00.0] sent 1 msg(s) of size:48
<idle>-0 [000] d.h1 756.161902: otx2_msg_interrupt: [0002:01:00.0] mbox interrupt PF(s) to AF (0x2)
kworker/u49:0-1165 [000] .... 756.162049: otx2_msg_process: [0002:01:00.0] msg:(0x400) error:0
kworker/u49:0-1165 [000] ...1 756.162051: otx2_msg_send: [0002:01:00.0] sent 1 msg(s) of size:32
kworker/u49:0-1165 [000] d.h. 756.162056: otx2_msg_interrupt: [0002:02:00.0] mbox interrupt AF to PF (0x1)
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Barry Song [Tue, 22 Sep 2020 01:56:15 +0000 (13:56 +1200)]
net: allwinner: remove redundant irqsave and irqrestore in hardIRQ
The comment "holders of db->lock must always block IRQs" and related
code to do irqsave and irqrestore don't make sense since we are in a
IRQ-disabled hardIRQ context.
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rikard Falkeborn [Mon, 21 Sep 2020 22:55:17 +0000 (00:55 +0200)]
net: hns3: Constify static structs
A number of static variables were not modified. Make them const to allow
the compiler to put them in read-only memory. In order to do so,
constify a couple of input pointers as well as some local pointers.
This moves about 35Kb to read-only memory as seen by the output of the
size command.
Before:
text data bss dec hex filename
404938 111534 640 517112 7e3f8 drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge.ko
After:
text data bss dec hex filename
439499 76974 640 517113 7e3f9 drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge.ko
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 23 Sep 2020 20:24:35 +0000 (13:24 -0700)]
Merge branch 'net-bridge-mcast-IGMPv3-MLDv2-fast-path-part-2'
Nikolay Aleksandrov says:
====================
net: bridge: mcast: IGMPv3/MLDv2 fast-path (part 2)
This is the second part of the IGMPv3/MLDv2 support which adds support
for the fast-path. In order to be able to handle source entries we add
mdb support for S,G entries (i.e. we add source address support to
br_ip), that requires to extend the current mdb netlink API, fortunately
we just add another attribute which will contain nested future mdb
attributes, then we use it to add support for S,G user- add, del and
dump. The lookup sequence is simple: when IGMPv3/MLDv2 are enabled do
the S,G lookup first and if it fails fallback to *,G. The more complex
part is when we begin handling source lists and auto-installing S,G entries
and *,G filter mode transitions. We have the following cases:
1) *,G INCLUDE -> EXCLUDE transition: we need to install the port in
all of *,G's installed S,G entries for proper replication (except
the ones explicitly blocked), this is also necessary when adding a
new *,G EXCLUDE port group
2) *,G EXCLUDE -> INCLUDE transition: we need to remove the port from
all of *,G's installed S,G entries, this is also necessary when
removing a *,G port group
3) New S,G port entry: we need to install all current *,G EXCLUDE ports
4) Remove S,G port entry: if all other port groups were auto-installed we
can safely remove them and delete the whole S,G entry
Currently we compute these operations from the available ports, their
source lists and their filter mode. In the future we can extend the port
group structure and reduce the running time of these ops. Also one
current limitation is that host-joined S,G entries are not supported.
I.e. one cannot add "dev bridge port bridge" mdb S,G entries. The host
join is currently considered an EXCLUDE {} join, so it's reflected in
all of *,G's installed S,G entries. If an S,G,port entry is added as
temporary then the kernel can take it over if a source shows up from a
report, permanent entries are skipped. In order to properly handle
blocked sources we add a new port group blocked flag to avoid forwarding
to that port group in the S,G. Finally when forwarding we use the port
group filter mode (if it's INCLUDE and the port group is from a *,G then
don't replicate to it, respectively if it's EXCLUDE then forward) and the
blocked flag (obviously if it's set - skip that port unless it's a
router port) to decide if the port should be skipped. Another limitation
is that we can't do some of the above transitions without small traffic
drop while installing/removing entries. That will be taken care of when
we add atomic swap of port replication lists later.
Patch break down:
patches 1-3: prepare the mdb code for better extack support which is
used in future patches to return a more meaningful error
patches 4-6: add the source address field to struct br_ip, and do minor
cleanups around it
patches 7-8: extend the mdb netlink API so we can send new mdb
attributes and uses the new API for S,G entry add/del/dump
support
patch 9: takes care of S,G entries when doing a lookup (first S,G
then *,G lookup)
patch 10: adds a new port group field and attribute for origin protocol
we use the already available RTPROT_ definitions,
currently user-space entries are added as RTPROT_STATIC and
kernel entries are added as RTPROT_KERNEL, we may allow
user-space to set custom values later (e.g. for FRR, clag)
patch 11: adds an internal S,G,port rhashtable to speed up filter
mode transitions
patch 12: initial automatic install of S,G entries based on port
groups' source lists
patch 13: handles port group modes on transitions or when new
port group entries are added
patch 14: self-explanatory - adds support for blocked port group
entries needed to stop forwarding to particular S,G,port
entries
patch 15: handles host-join/leave state changes, treats host-joins
as EXCLUDE {} groups (reflected in all *,G's S,G entries)
patch 16: finally adds the fast-path filter mode and block flag
support
Here're the sets that will come next (in order):
- iproute2 support for IGMPv3/MLDv2
- selftests for all mode transitions and group flags
- explicit host tracking for proper fast-leave support
- atomic port replication lists (these are also needed for broadcast
forwarding optimizations)
- mode transition optimization and removal of open-coded sorted lists
Not implemented yet:
- Host IGMPv3/MLDv2 filter support (currently we handle only join/leave
as before)
- Proper other querier source timer and value updates
- IGMPv3/v2 MLDv2/v1 compat (I have a few rough patches for this one)
v2: fix build with CONFIG_BATMAN_ADV_MCAST in patch 6
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:27 +0000 (10:30 +0300)]
net: bridge: mcast: when forwarding handle filter mode and blocked flag
We need to avoid forwarding to ports in MCAST_INCLUDE filter mode when the
mdst entry is a *,G or when the port has the blocked flag.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:26 +0000 (10:30 +0300)]
net: bridge: mcast: handle host state
Since host joins are considered as EXCLUDE {} joins we need to reflect
that in all of *,G ports' S,G entries. Since the S,Gs can have
host_joined == true only set automatically we can safely set it to false
when removing all automatically added entries upon S,G delete.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:25 +0000 (10:30 +0300)]
net: bridge: mcast: add support for blocked port groups
When excluding S,G entries we need a way to block a particular S,G,port.
The new port group flag is managed based on the source's timer as per
RFCs 3376 and 3810. When a source expires and its port group is in
EXCLUDE mode, it will be blocked.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:24 +0000 (10:30 +0300)]
net: bridge: mcast: handle port group filter modes
We need to handle group filter mode transitions and initial state.
To change a port group's INCLUDE -> EXCLUDE mode (or when we have added
a new port group in EXCLUDE mode) we need to add that port to all of
*,G ports' S,G entries for proper replication. When the EXCLUDE state is
changed from IGMPv3 report, br_multicast_fwd_filter_exclude() must be
called after the source list processing because the assumption is that
all of the group's S,G entries will be created before transitioning to
EXCLUDE mode, i.e. most importantly its blocked entries will already be
added so it will not get automatically added to them.
The transition EXCLUDE -> INCLUDE happens only when a port group timer
expires, it requires us to remove that port from all of *,G ports' S,G
entries where it was automatically added previously.
Finally when we are adding a new S,G entry we must add all of *,G's
EXCLUDE ports to it.
In order to distinguish automatically added *,G EXCLUDE ports we have a
new port group flag - MDB_PG_FLAGS_STAR_EXCL.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:23 +0000 (10:30 +0300)]
net: bridge: mcast: install S,G entries automatically based on reports
This patch adds support for automatic install of S,G mdb entries based
on the port group's source list and the source entry's timer.
Once installed the S,G will be used when forwarding packets if the
approprate multicast/mld versions are set. A new source flag called
BR_SGRP_F_INSTALLED denotes if the source has a forwarding mdb entry
installed.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:22 +0000 (10:30 +0300)]
net: bridge: mcast: add sg_port rhashtable
To speedup S,G forward handling we need to be able to quickly find out
if a port is a member of an S,G group. To do that add a global S,G port
rhashtable with key: source addr, group addr, protocol, vid (all br_ip
fields) and port pointer.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:21 +0000 (10:30 +0300)]
net: bridge: mcast: add rt_protocol field to the port group struct
We need to be able to differentiate between pg entries created by
user-space and the kernel when we start generating S,G entries for
IGMPv3/MLDv2's fast path. User-space entries are created by default as
RTPROT_STATIC and the kernel entries are RTPROT_KERNEL. Later we can
allow user-space to provide the entry rt_protocol so we can
differentiate between who added the entries specifically (e.g. clag,
admin, frr etc).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:20 +0000 (10:30 +0300)]
net: bridge: mcast: when igmpv3/mldv2 are enabled lookup (S,G) first, then (*,G)
If (S,G) entries are enabled (igmpv3/mldv2) then look them up first. If
there isn't a present (S,G) entry then try to find (*,G).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:19 +0000 (10:30 +0300)]
net: bridge: mdb: add support for add/del/dump of entries with source
Add new mdb attributes (MDBE_ATTR_SOURCE for setting,
MDBA_MDB_EATTR_SOURCE for dumping) to allow add/del and dump of mdb
entries with a source address (S,G). New S,G entries are created with
filter mode of MCAST_INCLUDE. The same attributes are used for IPv4 and
IPv6, they're validated and parsed based on their protocol.
S,G host joined entries which are added by user are not allowed yet.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:18 +0000 (10:30 +0300)]
net: bridge: mdb: add support to extend add/del commands
Since the MDB add/del code expects an exact struct br_mdb_entry we can't
really add any extensions, thus add a new nested attribute at the level of
MDBA_SET_ENTRY called MDBA_SET_ENTRY_ATTRS which will be used to pass
all new options via netlink attributes. This patch doesn't change
anything functionally since the new attribute is not used yet, only
parsed.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:17 +0000 (10:30 +0300)]
net: bridge: mcast: rename br_ip's u member to dst
Since now we have src in br_ip, u no longer makes sense so rename
it to dst. No functional changes.
v2: fix build with CONFIG_BATMAN_ADV_MCAST
CC: Marek Lindner <mareklindner@neomailbox.ch>
CC: Simon Wunderlich <sw@simonwunderlich.de>
CC: Antonio Quartulli <a@unstable.cc>
CC: Sven Eckelmann <sven@narfation.org>
CC: b.a.t.m.a.n@lists.open-mesh.org
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:16 +0000 (10:30 +0300)]
net: bridge: mcast: use br_ip's src for src groups and querier address
Now that we have src and dst in br_ip it is logical to use the src field
for the cases where we need to work with a source address such as
querier source address and group source address.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:15 +0000 (10:30 +0300)]
net: bridge: add src field to br_ip
Add a new src field to struct br_ip which will be used to lookup S, G
entries. When SSM option is added we will enable full br_ip lookups.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:14 +0000 (10:30 +0300)]
net: bridge: mdb: use extack in br_mdb_add() and br_mdb_add_group()
Pass and use extack all the way down to br_mdb_add_group().
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:13 +0000 (10:30 +0300)]
net: bridge: mdb: move all port and bridge checks to br_mdb_add
To avoid doing duplicate device checks and searches (the same were done
in br_mdb_add and __br_mdb_add) pass the already found port to __br_mdb_add
and pull the bridge's netif_running and enabled multicast checks to
br_mdb_add. This would also simplify the future extack errors.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 22 Sep 2020 07:30:12 +0000 (10:30 +0300)]
net: bridge: mdb: use extack in br_mdb_parse()
We can drop the pr_info() calls and just use extack to return a
meaningful error to user-space when br_mdb_parse() fails.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zheng Yongjun [Mon, 21 Sep 2020 13:32:09 +0000 (21:32 +0800)]
net: realtek: Remove set but not used variable
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/realtek/8139cp.c: In function cp_tx_timeout:
drivers/net/ethernet/realtek/8139cp.c:1242:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
`rc` is never used, so remove it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Luo bin [Mon, 21 Sep 2020 07:31:03 +0000 (15:31 +0800)]
hinic: improve the comments of function header
Fix the warnings about function header comments when building hinic
driver with "W=1" option.
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 23 Sep 2020 20:11:11 +0000 (13:11 -0700)]
Merge git://git./linux/kernel/git/bpf/bpf-next
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-09-23
The following pull-request contains BPF updates for your *net-next* tree.
We've added 95 non-merge commits during the last 22 day(s) which contain
a total of 124 files changed, 4211 insertions(+), 2040 deletions(-).
The main changes are:
1) Full multi function support in libbpf, from Andrii.
2) Refactoring of function argument checks, from Lorenz.
3) Make bpf_tail_call compatible with functions (subprograms), from Maciej.
4) Program metadata support, from YiFei.
5) bpf iterator optimizations, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Olsa [Wed, 23 Sep 2020 18:57:35 +0000 (20:57 +0200)]
tools resolve_btfids: Always force HOSTARCH
Seth reported problem with cross builds, that fail
on resolve_btfids build, because we are trying to
build it on cross build arch.
Fixing this by always forcing the host arch.
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200923185735.3048198-2-jolsa@kernel.org
Jiri Olsa [Wed, 23 Sep 2020 18:57:34 +0000 (20:57 +0200)]
bpf: Check CONFIG_BPF option for resolve_btfids
Currently all the resolve_btfids 'users' are under CONFIG_BPF
code, so if we have CONFIG_BPF disabled, resolve_btfids will
fail, because there's no data to resolve.
Disabling resolve_btfids if there's CONFIG_BPF disabled,
so we won't fail such builds.
Suggested-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200923185735.3048198-1-jolsa@kernel.org
David S. Miller [Wed, 23 Sep 2020 19:09:08 +0000 (12:09 -0700)]
Merge tag 'linux-can-next-for-5.10-
20200923' of git://git./linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2020-09-23
this is a pull request of 20 patches for net-next.
The complete series target the flexcan driver and is created by Joakim
Zhang and me.
The first six patches are cleanup (sort include files alphabetically,
remove stray empty line, get rid of long lines) and adding more
registers and documentation (registers and wakeup interrupt).
Then in two patches the transceiver regulator is made optional, and a
check for maximum transceiver bitrate is added.
Then the ECC support for HW thats supports this is added.
The next three patches improve suspend and low power mode handling.
Followed by six patches that add CAN-FD support and CAN-FD related
features.
The last two patches add support for the flexcan IP core on the imx8qm
and lx2160ar1.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 23 Sep 2020 19:07:55 +0000 (12:07 -0700)]
Merge branch 's390-qeth-next'
Julian Wiedmann says:
====================
s390/qeth: updates 2020-09-23
please apply the following patch series for qeth to netdev's net-next tree.
This brings all sorts of cleanups. Highlights are more code sharing in
the init/teardown paths, and more fine-grained rollback on errors during
initialization (instead of a full-blown teardown).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 23 Sep 2020 08:37:00 +0000 (10:37 +0200)]
s390/qeth: remove forward declarations in L2 code
Shuffle some code around (primarily all the discipline-related stuff) to
get rid of all the unnecessary forward declarations.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 23 Sep 2020 08:36:59 +0000 (10:36 +0200)]
s390/qeth: consolidate teardown code
Clarify which discipline-specific steps are needed to roll back after
error in qeth_l?_set_online(), and which are common to roll back
from qeth_hardsetup_card().
Some steps (cancelling the RX modeset, draining the TX queues) are only
necessary if the netdev was potentially UP before, so move them to the
common qeth_set_offline().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 23 Sep 2020 08:36:58 +0000 (10:36 +0200)]
s390/qeth: consolidate online code
Move duplicated code from the disciplines into the core path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 23 Sep 2020 08:36:57 +0000 (10:36 +0200)]
s390/qeth: cancel cmds earlier during teardown
Originators of cmd IO typically hold the rtnl or conf_mutex to protect
against a concurrent teardown.
Since qeth_set_offline() already holds the conf_mutex, the main reason
why we still care about cancelling pending cmds is so that they release
the rtnl when we need it ourselves.
So move this step a little earlier into the teardown sequence.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 23 Sep 2020 08:36:56 +0000 (10:36 +0200)]
s390/qeth: tighten ucast IP locking
The programming of ucast IPs via qeth_l3_modify_ip() is driven
independently from any of our typical locking mechanisms (eg. detaching
the netdevice, or holding the conf_mutex).
So when we inspect the card state to check whether the required cmd IO
should be deferred, there is no protection against concurrent state
changes.
But by slightly re-ordering the teardown sequence, we can rely on the
ip_lock to sufficiently serialize things:
1. when running concurrently to qeth_l3_set_online(), any instance of
qeth_l3_modify_ip() that aquires the ip_lock _after_
qeth_l3_recover_ip() will observe the state as CARD_STATE_SOFTSETUP
and not defer the IO.
2. when running concurrently to qeth_l3_set_offline(), any instance of
qeth_l3_modify_ip() that aquires the ip_lock _after_
qeth_l3_clear_ip_htable() will observe the state as CARD_STATE_DOWN
and defer the IO.
These guarantees in mind, we can now drop the conf_mutex from the
qeth_l3_modify_rxip_vipa() wrapper.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 23 Sep 2020 08:36:55 +0000 (10:36 +0200)]
s390/qeth: replace deprecated simple_stroul()
Convert the remaining occurences in sysfs code to kstrtouint().
While at it move some input parsing out of locked sections, replace an
open-coded clamp() and remove some unnecessary run-time checks for
ipatoe->mask_bits that are already enforced when creating the object.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 23 Sep 2020 08:36:54 +0000 (10:36 +0200)]
s390/qeth: clean up string ops in qeth_l3_parse_ipatoe()
Indicate the max number of to-be-parsed characters, and avoid copying
the address sub-string.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 23 Sep 2020 08:36:53 +0000 (10:36 +0200)]
s390/qeth: relax locking for ipato config data
card->ipato is currently protected by the conf_mutex. But most users
also hold the ip_lock - in particular qeth_l3_add_ip().
So slightly expand the sections under ip_lock in a few places (to
effectively cover a few error & no-op cases), and then drop the
conf_mutex where it's no longer needed.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 23 Sep 2020 08:36:52 +0000 (10:36 +0200)]
s390/qeth: don't init refcount twice for mcast IPs
mcast IP objects are allocated within qeth_l3_add_mcast_rtnl(),
with .ref_counter already set to 1 via qeth_l3_init_ipaddr().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenz Bauer [Wed, 23 Sep 2020 16:01:55 +0000 (17:01 +0100)]
bpf: Explicitly size compatible_reg_types
Arrays with designated initializers have an implicit length of the highest
initialized value plus one. I used this to ensure that newly added entries
in enum bpf_reg_type get a NULL entry in compatible_reg_types.
This is difficult to understand since it requires knowledge of the
peculiarities of designated initializers. Use __BPF_ARG_TYPE_MAX to size
the array instead.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200923160156.80814-1-lmb@cloudflare.com
Zheng Yongjun [Wed, 23 Sep 2020 03:21:40 +0000 (11:21 +0800)]
net: microchip: Make `lan743x_pm_suspend` function return right value
drivers/net/ethernet/microchip/lan743x_main.c: In function lan743x_pm_suspend:
`ret` is set but not used. In fact, `pci_prepare_to_sleep` function value should
be the right value of `lan743x_pm_suspend` function, therefore, fix it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 23 Sep 2020 00:44:59 +0000 (17:44 -0700)]
Merge tag 'mlx5-updates-2020-09-21' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-09-21
Multi packet TX descriptor support for SKBs.
This series introduces some refactoring of the regular TX data path in
mlx5 and adds the Enhanced TX MPWQE feature support. MPWQE stands for
multi-packet work queue element, and it can serve multiple packets,
reducing the PCI bandwidth spent on control traffic. It should improve
performance in scenarios where PCI is the bottleneck, and xmit_more is
signaled by the kernel. The refactoring done in this series also
improves the packet rate on its own.
MPWQE is already implemented in the XDP tx path, this series adds the
support of MPWQE for regular kernel SKB tx path.
MPWQE is supported from ConnectX-5 and onward, for legacy devices we need
to keep backward compatibility for regular (Single packet) WQE descriptor.
MPWQE is not compatible with certain offloads and features, such as TLS
offload, TSO, nonlinear SKBs. If such incompatible features are in use,
the driver gracefully falls back to non-MPWQE per SKB.
Prior to the final patch "net/mlx5e: Enhanced TX MPWQE for SKBs" that adds
the actual support, Maxim did some refactoring to the tx data path to
split it into stages and smaller helper functions that can be utilized and
reused for both legacy and new MPWQE feature.
Performance testing:
UDP performance is improved in a single stream pktgen test:
Packet rate: 16.86 Mpps (±0.15 Mpps) -> 20.94 Mpps (±0.33 Mpps)
Instructions per packet: 434 -> 329
Cycles per packet: 158 -> 123
Instructions per cycle: 2.75 -> 2.67
TCP and XDP_TX single stream tests show no performance difference.
MPWQE can reduce PCI bandwidth:
PCI Gen2, pktgen at fixed rate of
36864000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 80.3%
Inbound PCI utilization with MPWQE on: 59.0%
PCI Gen3, pktgen at fixed rate of
56064000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 65.4%
Inbound PCI utilization with MPWQE on: 49.3%
MPWQE can also reduce CPU load, increasing the packet rate in case of
CPU bottleneck:
PCI Gen2, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 37.5 Mpps
Packet rate with MPWQE on: 49.0 Mpps
PCI Gen3, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 57.0 Mpps
Packet rate with MPWQE on: 66.8 Mpps
Burst size in all pktgen tests is 32.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (x86_64)
NIC: Mellanox ConnectX-6 Dx
GCC 10.2.0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 23 Sep 2020 00:38:42 +0000 (17:38 -0700)]
Merge branch 'devlink-Use-nla_policy-to-validate-range'
Parav Pandit says:
====================
devlink: Use nla_policy to validate range
This two small patches uses nla_policy to validate user specified
fields are in valid range or not.
Patch summary:
Patch-1 checks the range of eswitch mode field
Patch-2 checks for the port type field. It eliminates a check in
code by using nla policy infrastructure.
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parav Pandit [Mon, 21 Sep 2020 16:41:30 +0000 (19:41 +0300)]
devlink: Enhance policy to validate port type input value
Use range checking facility of nla_policy to validate port type
attribute input value is valid or not.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parav Pandit [Mon, 21 Sep 2020 16:41:29 +0000 (19:41 +0300)]
devlink: Enhance policy to validate eswitch mode value
Use range checking facility of nla_policy to validate eswitch mode input
attribute value is valid or not.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 22 Sep 2020 23:45:34 +0000 (16:45 -0700)]
Merge git://git./linux/kernel/git/netdev/net
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 22 Sep 2020 22:08:41 +0000 (15:08 -0700)]
Merge branch 'fixes' of git://git./linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"No common topic, just assorted fixes"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fuse: fix the ->direct_IO() treatment of iov_iter
fs: fix cast in fsparam_u32hex() macro
vboxsf: Fix the check for the old binary mount-arguments struct
Linus Torvalds [Tue, 22 Sep 2020 21:43:50 +0000 (14:43 -0700)]
Merge git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
- fix failure to add bond interfaces to a bridge, the offload-handling
code was too defensive there and recent refactoring unearthed that.
Users complained (Ido)
- fix unnecessarily reflecting ECN bits within TOS values / QoS marking
in TCP ACK and reset packets (Wei)
- fix a deadlock with bpf iterator. Hopefully we're in the clear on
this front now... (Yonghong)
- BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)
- fix AQL on mt76 devices with FW rate control and add a couple of AQL
issues in mac80211 code (Felix)
- fix authentication issue with mwifiex (Maximilian)
- WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)
- fix exception handling for multipath routes via same device (David
Ahern)
- revert back to a BH spin lock flavor for nsid_lock: there are paths
which do require the BH context protection (Taehee)
- fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)
- fix ife module load deadlock (Cong)
- make an adjustment to netlink reply message type for code added in
this release (the sole change touching uAPI here) (Michal)
- a number of fixes for small NXP and Microchip switches (Vladimir)
[ Pull request acked by David: "you can expect more of this in the
future as I try to delegate more things to Jakub" ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
net: Update MAINTAINERS for MediaTek switch driver
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
net/mlx5e: kTLS, Fix leak on resync error flow
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
net/mlx5e: Fix endianness when calculating pedit mask first bit
net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
net/mlx5e: CT: Fix freeing ct_label mapping
net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
net/mlx5e: Use synchronize_rcu to sync with NAPI
net/mlx5e: Use RCU to protect rq->xdp_prog
...
Linus Torvalds [Tue, 22 Sep 2020 21:36:50 +0000 (14:36 -0700)]
Merge tag 'io_uring-5.9-2020-09-22' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"A few fixes - most of them regression fixes from this cycle, but also
a few stable heading fixes, and a build fix for the included demo tool
since some systems now actually have gettid() available"
* tag 'io_uring-5.9-2020-09-22' of git://git.kernel.dk/linux-block:
io_uring: fix openat/openat2 unified prep handling
io_uring: mark statx/files_update/epoll_ctl as non-SQPOLL
tools/io_uring: fix compile breakage
io_uring: don't use retry based buffered reads for non-async bdev
io_uring: don't re-setup vecs/iter in io_resumit_prep() is already there
io_uring: don't run task work on an exiting task
io_uring: drop 'ctx' ref on task work cancelation
io_uring: grab any needed state during defer prep
Linus Torvalds [Tue, 22 Sep 2020 21:31:38 +0000 (14:31 -0700)]
Merge tag 'block-5.9-2020-09-22' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A few NVMe fixes, and a dasd write zero fix"
* tag 'block-5.9-2020-09-22' of git://git.kernel.dk/linux-block:
nvmet: get transport reference for passthru ctrl
nvme-core: get/put ctrl and transport module in nvme_dev_open/release()
nvme-tcp: fix kconfig dependency warning when !CRYPTO
nvme-pci: disable the write zeros command for Intel 600P/P3100
s390/dasd: Fix zero write for FBA devices
Linus Torvalds [Tue, 22 Sep 2020 16:08:33 +0000 (09:08 -0700)]
Merge tag 'trace-v5.9-rc5' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Check kprobe is enabled before unregistering from ftrace as it isn't
registered when disabled.
- Remove kprobes enabled via command-line that is on init text when
freed.
- Add missing RCU synchronization for ftrace trampoline symbols removed
from kallsyms.
- Free trampoline on error path if ftrace_startup() fails.
- Give more space for the longer PID numbers in trace output.
- Fix a possible double free in the histogram code.
- A couple of fixes that were discovered by sparse.
* tag 'trace-v5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
bootconfig: init: make xbc_namebuf static
kprobes: tracing/kprobes: Fix to kill kprobes on initmem after boot
tracing: fix double free
ftrace: Let ftrace_enable_sysctl take a kernel pointer buffer
tracing: Make the space reserved for the pid wider
ftrace: Fix missing synchronize_rcu() removing trampoline from kallsyms
ftrace: Free the trampoline when ftrace_startup() fails
kprobes: Fix to check probe enabled before disarm_kprobe_ftrace()
Joakim Zhang [Fri, 12 Jul 2019 08:03:01 +0000 (08:03 +0000)]
can: flexcan: add lx2160ar1 support
The Flexcan on lx2160ar1 supports CAN FD protocol.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20190712075926.7357-9-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Joakim Zhang [Fri, 12 Jul 2019 08:02:59 +0000 (08:02 +0000)]
can: flexcan: add imx8qm support
The Flexcan on i.MX8QM supports CAN FD protocol.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20190712075926.7357-8-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Joakim Zhang [Fri, 12 Jul 2019 08:02:56 +0000 (08:02 +0000)]
can: flexcan: add Transceiver Delay Compensation support
The CAN-FD protocol allows the transmission and reception of data at a
higher bit rate than the nominal rate used in the arbitration phase when
the message's BRS bit is set.
The TDC mechanism is effective only during the data phase of FD frames
having BRS bit set. It has no effect either on non-FD frames, or on FD
frames transmitted at normal bit rate.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20190712075926.7357-7-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Joakim Zhang [Fri, 12 Jul 2019 08:02:47 +0000 (08:02 +0000)]
can: flexcan: add CAN FD BRS support
This patch adds CAN FD BitRate Switch (BRS) support to driver.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20190712075926.7357-5-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Joakim Zhang [Fri, 12 Jul 2019 08:02:51 +0000 (08:02 +0000)]
can: flexcan: add ISO CAN FD feature support
ISO CAN FD is introduced to increase the failture detection capability
than non-ISO CAN FD. The non-ISO CAN FD is still supported by FlexCAN so
that it can be used mainly during an intermediate phase, for evaluation
and development purposes.
Therefore, it is strongly recommended to configure FlexCAN to the ISO
CAN FD protocol by setting the ISOCANFDEN field in the CTRL2 register.
NOTE: If you only set "fd on", driver will use ISO FD mode by default.
You should set "fd-non-iso on" after setting "fd on" if you want to use
NON ISO FD mode.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20190712075926.7357-6-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Joakim Zhang [Fri, 12 Jul 2019 08:02:44 +0000 (08:02 +0000)]
can: flexcan: add CAN-FD mode support
This patch adds CAN-FD mode support to the driver, it means that
payload size can extend up to 64 bytes.
Bit timing always set in the CBT register, not in the CTRL1 register any
more. This has an extend range of all CAN bit timing variables (PRESDIV,
PROPSEG, PSEG1, PSEG2 and RJW), which will improve the bit timing
accuracy.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
[mkl: move cbt-based bitrate support into separate function]
Link: https://lore.kernel.org/r/20200922144429.2613631-16-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Joakim Zhang [Fri, 12 Jul 2019 08:02:41 +0000 (08:02 +0000)]
can: flexcan: use struct canfd_frame for CAN classic frame
This patch prepares for CAN FD mode, using struct canfd_frame can both
for classic format frame and fd format frame.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20190712075926.7357-3-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 22 Sep 2020 14:44:22 +0000 (16:44 +0200)]
can: flexcan: flexcan_set_bittiming(): move setup of CAN-2.0 bitiming into separate function
This is a patch prepares for the CAN-FD support. In a later patch the
setup for canfd bittiming will be added, with this patch the change is
easier to read.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-14-mkl@pengutronix.de
Joakim Zhang [Wed, 4 Dec 2019 11:36:19 +0000 (11:36 +0000)]
can: flexcan: add LPSR mode support
On the i.MX7D in LPSR mode, the controller will be powered off and the
configuration state is lost after system resume. Upcoming i.MX8QM/QXP
will also completely power off the domain, the controller state is lost
and needs restore, too. So we need to set the pinctrl state again and
re-start chip to re-configuration after resume.
For the wakeup case, it should not set pinctrl to sleep state by
pinctrl_pm_select_sleep_state.
If the interface is down before suspend, we don't need to re-configure
it as it will be configured if the interface is brought up later.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20191204113249.3381-7-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Joakim Zhang [Tue, 10 Dec 2019 09:00:13 +0000 (09:00 +0000)]
can: flexcan: disable clocks during stop mode
Disable clocks while CAN core is in stop mode.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20191210085721.9853-2-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Joakim Zhang [Tue, 22 Sep 2020 14:44:19 +0000 (16:44 +0200)]
can: flexcan: flexcan_chip_stop(): add error handling and propagate error value
This patch implements error handling and propagates the error value of
flexcan_chip_stop(). This function will be called from flexcan_suspend()
in an upcoming patch in some SoCs which support LPSR mode.
Add a new function flexcan_chip_stop_disable_on_error() that tries to
disable the chip even in case of errors.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
[mkl: introduce flexcan_chip_stop_disable_on_error() and use it in flexcan_close()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-11-mkl@pengutronix.de
Joakim Zhang [Thu, 16 Apr 2020 09:31:25 +0000 (17:31 +0800)]
can: flexcan: add correctable errors correction when HW supports ECC
commit
cdce844865be ("can: flexcan: add vf610 support for FlexCAN")
From above commit by Stefan Agner, the patch just disables
non-correctable errors interrupt and freeze mode. It still can correct
the correctable errors since ECC enabled by default after reset (MECR[ECCDIS]=0,
enable memory error correct) if HW supports ECC.
commit
5e269324db5a ("can: flexcan: disable completely the ECC mechanism")
From above commit by Joakim Zhang, the patch disables ECC completely (assert
MECR[ECCDIS]) according to the explanation of FLEXCAN_QUIRK_DISABLE_MECR that
disable memory error detection. This cause correctable errors cannot be
corrected even HW supports ECC.
The error correction mechanism ensures that in this 13-bit word, errors
in one bit can be corrected (correctable errors) and errors in two bits can
be detected but not corrected (non-correctable errors). Errors in more than
two bits may not be detected.
If HW supports ECC, we can use this to correct the correctable errors detected
from FlexCAN memory. Then disable non-correctable errors interrupt and freeze
mode to avoid that put FlexCAN in freeze mode.
This patch adds correctable errors correction when HW supports ECC, and
modify explanation for FLEXCAN_QUIRK_DISABLE_MECR.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20200416093126.15242-1-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Joakim Zhang [Wed, 30 Oct 2019 06:45:57 +0000 (06:45 +0000)]
can: flexcan: Add check for transceiver maximum bitrate limitation
CAN FD can transmit up to 8Mbps, but some transceivers only can support
5Mbps, so add check in driver.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20191030064245.12923-2-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 22 Sep 2020 14:44:16 +0000 (16:44 +0200)]
can: flexcan: flexcan_probe(): make regulator xceiver optional
As the transcevier regulator is optional, this patch switches from
devm_regulator_get() to devm_regulator_get_optional(). This gets rid of "using
dummy regulator" warning message from the regulator core, if no regulator is
available.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-8-mkl@pengutronix.de
Joakim Zhang [Wed, 4 Dec 2019 11:36:08 +0000 (11:36 +0000)]
can: flexcan: Ack wakeup interrupt separately
As FLEXCAN_ESR_ALL_INT is for all bus errors and state change IRQ
sources, strictly speaking FLEXCAN_ESR_WAK_INT does not belong to these.
So add wakeup interrupt ack separately to existing ack of the
interrupts.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20191204113249.3381-3-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 22 Sep 2020 14:44:14 +0000 (16:44 +0200)]
can: flexcan: quirks: get rid of long lines
This patch reformats the quirks to get rid of long lines.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-6-mkl@pengutronix.de
Marc Kleine-Budde [Tue, 22 Sep 2020 14:44:13 +0000 (16:44 +0200)]
can: flexcan: struct flexcan_regs: document registers not affected by soft reset
This patch documents which registers are not affected by a soft reset of the
flexcan IP core.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-5-mkl@pengutronix.de
Marc Kleine-Budde [Tue, 22 Sep 2020 14:44:12 +0000 (16:44 +0200)]
can: flexcan: more register names
This patch adds some new register names and tries to ensure with a
static_assert that the documented offset is correct.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-4-mkl@pengutronix.de
Marc Kleine-Budde [Tue, 22 Sep 2020 14:44:11 +0000 (16:44 +0200)]
can: flexcan: flexcan_exit_stop_mode(): remove stray empty line
This patch removes a stray empty line from the flexcan_exit_stop_mode()
function.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-3-mkl@pengutronix.de
Marc Kleine-Budde [Tue, 22 Sep 2020 14:44:10 +0000 (16:44 +0200)]
can: flexcan: sort include files alphabetically
This patch sorts the include files alphabetically.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-2-mkl@pengutronix.de
Maxim Mikityanskiy [Thu, 2 Jul 2020 09:37:29 +0000 (12:37 +0300)]
net/mlx5e: Enhanced TX MPWQE for SKBs
This commit adds support for Enhanced TX MPWQE feature in the regular
(SKB) data path. A MPWQE (multi-packet work queue element) can serve
multiple packets, reducing the PCI bandwidth on control traffic.
Two new stats (tx*_mpwqe_blks and tx*_mpwqe_pkts) are added. The feature
is on by default and controlled by the skb_tx_mpwqe private flag.
In a MPWQE, eseg is shared among all packets, so eseg-based offloads
(IPSEC, GENEVE, checksum) run on a separate eseg that is compared to the
eseg of the current MPWQE session to decide if the new packet can be
added to the same session.
MPWQE is not compatible with certain offloads and features, such as TLS
offload, TSO, nonlinear SKBs. If such incompatible features are in use,
the driver gracefully falls back to non-MPWQE.
This change has no performance impact in TCP single stream test and
XDP_TX single stream test.
UDP pktgen, 64-byte packets, single stream, MPWQE off:
Packet rate: 16.96 Mpps (±0.12 Mpps) -> 17.01 Mpps (±0.20 Mpps)
Instructions per packet: 421 -> 429
Cycles per packet: 156 -> 161
Instructions per cycle: 2.70 -> 2.67
UDP pktgen, 64-byte packets, single stream, MPWQE on:
Packet rate: 16.96 Mpps (±0.12 Mpps) -> 20.94 Mpps (±0.33 Mpps)
Instructions per packet: 421 -> 329
Cycles per packet: 156 -> 123
Instructions per cycle: 2.70 -> 2.67
Enabling MPWQE can reduce PCI bandwidth:
PCI Gen2, pktgen at fixed rate of
36864000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 80.3%
Inbound PCI utilization with MPWQE on: 59.0%
PCI Gen3, pktgen at fixed rate of
56064000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 65.4%
Inbound PCI utilization with MPWQE on: 49.3%
Enabling MPWQE can also reduce CPU load, increasing the packet rate in
case of CPU bottleneck:
PCI Gen2, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 37.5 Mpps
Packet rate with MPWQE on: 49.0 Mpps
PCI Gen3, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 57.0 Mpps
Packet rate with MPWQE on: 66.8 Mpps
Burst size in all pktgen tests is 32.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (x86_64)
NIC: Mellanox ConnectX-6 Dx
GCC 10.2.0
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Mon, 9 Dec 2019 13:07:57 +0000 (15:07 +0200)]
net/mlx5e: Move TX code into functions to be used by MPWQE
mlx5e_txwqe_complete performs some actions that can be taken to separate
functions:
1. Update the flags needed for hardware timestamping.
2. Stop the TX queue if it's full.
Take these actions into separate functions to be reused by the MPWQE
code in the following commit and to maintain clear responsibilities of
functions.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Thu, 16 Apr 2020 08:30:14 +0000 (11:30 +0300)]
net/mlx5e: Rename xmit-related structs to generalize them
As preparation for the upcoming TX MPWQE support for SKBs, rename struct
mlx5e_xdp_mpwqe to mlx5e_tx_mpwqe and move it above struct mlx5e_txqsq.
This structure will be reused in the regular SQ and in the regular TX
data path. Also rename mlx5e_xdp_xmit_data to mlx5e_xmit_data - it will
be used in the upcoming TX MPWQE flow.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Thu, 4 Jun 2020 13:43:27 +0000 (16:43 +0300)]
net/mlx5e: Generalize TX MPWQE checks for full session
As preparation for the upcoming TX MPWQE for SKBs, create a function
(mlx5e_tx_mpwqe_is_full) to check whether an MPWQE session is full. This
function will be shared by MPWQE code for XDP and for SKBs. Defines are
renamed and moved to make them not XDP-specific.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Thu, 16 Apr 2020 08:30:33 +0000 (11:30 +0300)]
net/mlx5e: Support multiple SKBs in a TX WQE
TX MPWQE support for SKBs is coming in one of the following patches, and
a single MPWQE can send multiple SKBs. This commit prepares the TX path
code to handle such cases:
1. An additional FIFO for SKBs is added, just like the FIFO for DMA
chunks.
2. struct mlx5e_tx_wqe_info will contain num_fifo_pkts. If a given WQE
contains only one packet, num_fifo_pkts will be zero, and the SKB will
be stored in mlx5e_tx_wqe_info, as usual. If num_fifo_pkts > 0, the SKB
pointer will be NULL, and the SKBs will be stored in the FIFO.
This change has no performance impact in TCP single stream test and
XDP_TX single stream test.
When compiled with a recent GCC, this change shows no visible
performance impact on UDP pktgen (burst 32) single stream test either:
Packet rate: 16.95 Mpps (±0.15 Mpps) -> 16.96 Mpps (±0.12 Mpps)
Instructions per packet: 429 -> 421
Cycles per packet: 160 -> 156
Instructions per cycle: 2.69 -> 2.70
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (x86_64)
NIC: Mellanox ConnectX-6 Dx
GCC 10.2.0
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Thu, 30 Jul 2020 14:53:46 +0000 (17:53 +0300)]
net/mlx5e: Move the TLS resync check out of the function
Before this patch, mlx5e_ktls_tx_handle_resync_dump_comp checked for
resync_dump_frag_page. It happened for all WQEs without an SKB,
including padding WQEs, and required a function call. Normally, padding
WQEs happen more often than TLS resyncs. Take this check out of the
function and put it to an inline function to save a call on all padding
WQEs.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Thu, 9 Jul 2020 11:05:31 +0000 (14:05 +0300)]
net/mlx5e: Unify constants for WQE_EMPTY_DS_COUNT
A constant for the number of DS in an empty WQE (i.e. a WQE without data
segments) is needed in multiple places (normal TX data path, MPWQE in
XDP), but currently we have a constant for XDP and an inline formula in
normal TX. This patch introduces a common constant.
Additionally, mlx5e_xdp_mpwqe_session_start is converted to use struct
assignment, because the code nearby is touched.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Thu, 30 Jul 2020 13:14:58 +0000 (16:14 +0300)]
net/mlx5e: Small improvements for XDP TX MPWQE logic
Use MLX5E_XDP_MPW_MAX_WQEBBS to reserve space for a MPWQE, because it's
actually the maximal size a MPWQE can take.
Reorganize the logic that checks when to close the MPWQE session:
1. Put all checks into a single function.
2. When inline is on, make only one comparison - if it's false, the less
strict one will also be false. The compiler probably optimized it out
anyway, but it's clearer to also reflect it in the code.
The MLX5E_XDP_INLINE_WQE_* defines are also changed to make the
calculations more correct from the logical point of view. Though
MLX5E_XDP_INLINE_WQE_MAX_DS_CNT used to be 16 and didn't change its
value, the calculation used to be DIV_ROUND_UP(max inline packet size,
MLX5_SEND_WQE_DS), and the numerator should have included sizeof(struct
mlx5_wqe_inline_seg).
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Fri, 14 Feb 2020 09:22:49 +0000 (11:22 +0200)]
net/mlx5e: Refactor xmit functions
A huge function mlx5e_sq_xmit was split into several to achieve multiple
goals:
1. Reuse the code in IPoIB.
2. Better intergrate with TLS, IPSEC, GENEVE and checksum offloads. Now
it's possible to reserve space in the WQ before running eseg-based
offloads, so:
2.1. It's not needed to copy cseg and eseg after mlx5e_fill_sq_frag_edge
anymore.
2.2. mlx5e_txqsq_get_next_pi will be used instead of the legacy
mlx5e_fill_sq_frag_edge for better code maintainability and reuse.
3. Prepare for the upcoming TX MPWQE for SKBs. It will intervene after
mlx5e_sq_calc_wqe_attr to check if it's possible to use MPWQE, and the
code flow will split into two paths: MPWQE and non-MPWQE.
Two high-level functions are provided to send packets:
* mlx5e_xmit is called by the networking stack, runs offloads and sends
the packet. In one of the following patches, MPWQE support will be added
to this flow.
* mlx5e_sq_xmit_simple is called by the TLS offload, runs only the
checksum offload and sends the packet.
This change has no performance impact in TCP single stream test and
XDP_TX single stream test.
When compiled with a recent GCC, this change shows no visible
performance impact on UDP pktgen (burst 32) single stream test either:
Packet rate: 16.86 Mpps (±0.15 Mpps) -> 16.95 Mpps (±0.15 Mpps)
Instructions per packet: 434 -> 429
Cycles per packet: 158 -> 160
Instructions per cycle: 2.75 -> 2.69
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (x86_64)
NIC: Mellanox ConnectX-6 Dx
GCC 10.2.0
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Tue, 8 Sep 2020 08:03:51 +0000 (11:03 +0300)]
net/mlx5e: Move mlx5e_tx_wqe_inline_mode to en_tx.c
Move mlx5e_tx_wqe_inline_mode from en/txrx.h to en_tx.c as it's only
used there.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Tue, 8 Sep 2020 07:46:09 +0000 (10:46 +0300)]
net/mlx5e: Use struct assignment to initialize mlx5e_tx_wqe_info
Struct assignment guarantees that all fields of the structure are
initialized (those that are not mentioned are zeroed). It makes code
mode robust and reduces chances for unpredictable behavior when one
forgets to reset some field and it holds an old value from previous
iterations of using the structure.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maxim Mikityanskiy [Mon, 9 Dec 2019 13:39:32 +0000 (15:39 +0200)]
net/mlx5e: Refactor inline header size calculation in the TX path
As preparation for the next patch, don't increase ihs to calculate
ds_cnt and then decrease it, but rather calculate the intermediate value
temporarily. This code has the same amount of arithmetic operations, but
now allows to split out ds_cnt calculation, which will be performed in
the next patch.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
David S. Miller [Tue, 22 Sep 2020 00:40:53 +0000 (17:40 -0700)]
Merge branch 'Fix-broken-tc-flower-rules-for-mscc_ocelot-switches'
Vladimir Oltean says:
====================
Fix broken tc-flower rules for mscc_ocelot switches
All 3 switch drivers from the Ocelot family have the same bug in the
VCAP IS2 key offsets, which is that some keys are in the incorrect
order.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 21 Sep 2020 22:56:38 +0000 (01:56 +0300)]
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
The IS2 IP4_TCP_UDP key offsets do not correspond to the VSC7514
datasheet. Whether they work or not is unknown to me. On VSC9959 and
VSC9953, with the same mistake and same discrepancy from the
documentation, tc-flower src_port and dst_port rules did not work, so I
am assuming the same is true here.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 21 Sep 2020 22:56:37 +0000 (01:56 +0300)]
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
Since these were copied from the Felix VCAP IS2 code, and only the
offsets were adjusted, the order of the bit fields is still wrong.
Fix it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xiaoliang Yang [Mon, 21 Sep 2020 22:56:36 +0000 (01:56 +0300)]
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
Some of the IS2 IP4_TCP_UDP keys are not correct, like L4_DPORT,
L4_SPORT and other L4 keys. This prevents offloaded tc-flower rules from
matching on src_port and dst_port for TCP and UDP packets.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 21 Sep 2020 14:27:20 +0000 (07:27 -0700)]
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
User space could send an invalid INET_DIAG_REQ_PROTOCOL attribute
as caught by syzbot.
BUG: KMSAN: uninit-value in inet_diag_lock_handler net/ipv4/inet_diag.c:55 [inline]
BUG: KMSAN: uninit-value in __inet_diag_dump+0x58c/0x720 net/ipv4/inet_diag.c:1147
CPU: 0 PID: 8505 Comm: syz-executor174 Not tainted 5.9.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x21c/0x280 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:122
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:219
inet_diag_lock_handler net/ipv4/inet_diag.c:55 [inline]
__inet_diag_dump+0x58c/0x720 net/ipv4/inet_diag.c:1147
inet_diag_dump_compat+0x2a5/0x380 net/ipv4/inet_diag.c:1254
netlink_dump+0xb73/0x1cb0 net/netlink/af_netlink.c:2246
__netlink_dump_start+0xcf2/0xea0 net/netlink/af_netlink.c:2354
netlink_dump_start include/linux/netlink.h:246 [inline]
inet_diag_rcv_msg_compat+0x5da/0x6c0 net/ipv4/inet_diag.c:1288
sock_diag_rcv_msg+0x24f/0x620 net/core/sock_diag.c:256
netlink_rcv_skb+0x6d7/0x7e0 net/netlink/af_netlink.c:2470
sock_diag_rcv+0x63/0x80 net/core/sock_diag.c:275
netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline]
netlink_unicast+0x11c8/0x1490 net/netlink/af_netlink.c:1330
netlink_sendmsg+0x173a/0x1840 net/netlink/af_netlink.c:1919
sock_sendmsg_nosec net/socket.c:651 [inline]
sock_sendmsg net/socket.c:671 [inline]
____sys_sendmsg+0xc82/0x1240 net/socket.c:2353
___sys_sendmsg net/socket.c:2407 [inline]
__sys_sendmsg+0x6d1/0x820 net/socket.c:2440
__do_sys_sendmsg net/socket.c:2449 [inline]
__se_sys_sendmsg+0x97/0xb0 net/socket.c:2447
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2447
do_syscall_64+0x9f/0x140 arch/x86/entry/common.c:48
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x441389
Code: e8 fc ab 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 1b 09 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007fff3b02ce98 EFLAGS:
00000246 ORIG_RAX:
000000000000002e
RAX:
ffffffffffffffda RBX:
0000000000000000 RCX:
0000000000441389
RDX:
0000000000000000 RSI:
0000000020001500 RDI:
0000000000000003
RBP:
00000000006cb018 R08:
00000000004002c8 R09:
00000000004002c8
R10:
0000000000000004 R11:
0000000000000246 R12:
0000000000402130
R13:
00000000004021c0 R14:
0000000000000000 R15:
0000000000000000
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:143 [inline]
kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:126
kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:80
slab_alloc_node mm/slub.c:2907 [inline]
__kmalloc_node_track_caller+0x9aa/0x12f0 mm/slub.c:4511
__kmalloc_reserve net/core/skbuff.c:142 [inline]
__alloc_skb+0x35f/0xb30 net/core/skbuff.c:210
alloc_skb include/linux/skbuff.h:1094 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1176 [inline]
netlink_sendmsg+0xdb9/0x1840 net/netlink/af_netlink.c:1894
sock_sendmsg_nosec net/socket.c:651 [inline]
sock_sendmsg net/socket.c:671 [inline]
____sys_sendmsg+0xc82/0x1240 net/socket.c:2353
___sys_sendmsg net/socket.c:2407 [inline]
__sys_sendmsg+0x6d1/0x820 net/socket.c:2440
__do_sys_sendmsg net/socket.c:2449 [inline]
__se_sys_sendmsg+0x97/0xb0 net/socket.c:2447
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2447
do_syscall_64+0x9f/0x140 arch/x86/entry/common.c:48
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes:
3f935c75eb52 ("inet_diag: support for wider protocol numbers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Christoph Paasch <cpaasch@apple.com>
Cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 21 Sep 2020 22:07:09 +0000 (01:07 +0300)]
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
When calling the RCU brother of br_vlan_get_pvid(), lockdep warns:
=============================
WARNING: suspicious RCU usage
5.9.0-rc3-01631-g13c17acb8e38-dirty #814 Not tainted
-----------------------------
net/bridge/br_private.h:1054 suspicious rcu_dereference_protected() usage!
Call trace:
lockdep_rcu_suspicious+0xd4/0xf8
__br_vlan_get_pvid+0xc0/0x100
br_vlan_get_pvid_rcu+0x78/0x108
The warning is because br_vlan_get_pvid_rcu() calls nbp_vlan_group()
which calls rtnl_dereference() instead of rcu_dereference(). In turn,
rtnl_dereference() calls rcu_dereference_protected() which assumes
operation under an RCU write-side critical section, which obviously is
not the case here. So, when the incorrect primitive is used to access
the RCU-protected VLAN group pointer, READ_ONCE() is not used, which may
cause various unexpected problems.
I'm sad to say that br_vlan_get_pvid() and br_vlan_get_pvid_rcu() cannot
share the same implementation. So fix the bug by splitting the 2
functions, and making br_vlan_get_pvid_rcu() retrieve the VLAN groups
under proper locking annotations.
Fixes:
7582f5b70f9a ("bridge: add br_vlan_get_pvid_rcu()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 22 Sep 2020 00:32:42 +0000 (17:32 -0700)]
Merge tag 'mlx5-fixes-2020-09-18' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes-2020-09-18
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
v1->v2:
Remove missing patch from -stable list.
For -stable v5.1
('net/mlx5: Fix FTE cleanup')
For -stable v5.3
('net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported')
('net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported')
For -stable v5.7
('net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready')
For -stable v5.8
('net/mlx5e: Use RCU to protect rq->xdp_prog')
('net/mlx5e: Fix endianness when calculating pedit mask first bit')
('net/mlx5e: Use synchronize_rcu to sync with NAPI')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Wang [Mon, 21 Sep 2020 23:09:23 +0000 (07:09 +0800)]
net: Update MAINTAINERS for MediaTek switch driver
Update maintainers for MediaTek switch driver with Landen Chao who is
familiar with MediaTek MT753x switch devices and will help maintenance
from the vendor side.
Cc: Steven Liu <steven.liu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Fri, 11 Sep 2020 18:00:06 +0000 (11:00 -0700)]
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
Returning errno is a bug, fix that.
Also fixes smatch warnings:
drivers/net/ethernet/mellanox/mlx5/core/en/port.c:453
mlx5e_fec_in_caps() warn: signedness bug returning '(-95)'
Fixes:
2132b71f78d2 ("net/mlx5e: Advertise globaly supported FEC modes")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Saeed Mahameed [Tue, 8 Sep 2020 05:54:43 +0000 (22:54 -0700)]
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
The spinlock only needed when accessing the channel's icosq, grab the lock
after the buf allocation in resync_post_get_progress_params() to avoid
kzalloc(GFP_KERNEL) in atomic context.
Fixes:
0419d8c9d8f8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Reported-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Saeed Mahameed [Fri, 11 Sep 2020 04:16:04 +0000 (21:16 -0700)]
net/mlx5e: kTLS, Fix leak on resync error flow
Resync progress params buffer and dma weren't released on error,
Add missing error unwinding for resync_post_get_progress_params().
Fixes:
0419d8c9d8f8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Saeed Mahameed [Tue, 8 Sep 2020 05:58:50 +0000 (22:58 -0700)]
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
Progress params dma address is never unmapped, unmap it when completion
handling is over.
Fixes:
0419d8c9d8f8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Tariq Toukan [Mon, 10 Aug 2020 12:59:41 +0000 (15:59 +0300)]
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
Using synchronize_rcu() is sufficient to wait until running NAPI quits.
See similar upstream fix with detailed explanation:
("net/mlx5e: Use synchronize_rcu to sync with NAPI")
This change also fixes a possible use-after-free as the NAPI
might be already released at this stage.
Fixes:
0419d8c9d8f8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tariq Toukan [Sun, 28 Jun 2020 10:06:06 +0000 (13:06 +0300)]
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
The set of TLS TX global SW counters in mlx5e_tls_sw_stats_desc
is updated from all rings by using atomic ops.
This set of stats is used only in the FPGA TLS use case, not in
the Connect-X TLS one, where regular per-ring counters are used.
Do not expose them in the Connect-X use case, as this would cause
counter duplication. For example, tx_tls_drop_no_sync_data would
appear twice in the ethtool stats.
Fixes:
d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Alaa Hleihel [Tue, 25 Aug 2020 07:41:50 +0000 (10:41 +0300)]
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
The cited commit started to reuse function mlx5e_update_ndo_stats() for
the representors as well.
However, the function is hard-coded to work on mlx5e_nic_stats_grps only.
Due to this issue, the representors statistics were not updated in the
output of "ip -s".
Fix it to work with the correct group by extracting it from the caller's
profile.
Also, while at it and since this function became generic, move it to
en_stats.c and rename it accordingly.
Fixes:
8a236b15144b ("net/mlx5e: Convert rep stats to mlx5e_stats_grp-based infra")
Signed-off-by: Alaa Hleihel <alaa@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Ron Diskin [Sun, 10 May 2020 11:39:51 +0000 (14:39 +0300)]
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
Currently the FW does not generate events for counters other than error
counters. Unlike ".get_ethtool_stats", ".ndo_get_stats64" (which ip -s
uses) might run in atomic context, while the FW interface is non atomic.
Thus, 'ip' is not allowed to issue FW commands, so it will only display
cached counters in the driver.
Add a SW counter (mcast_packets) in the driver to count rx multicast
packets. The counter also counts broadcast packets, as we consider it a
special case of multicast.
Use the counter value when calling "ip -s"/"ifconfig".
Fixes:
f62b8bb8f2d3 ("net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality")
Signed-off-by: Ron Diskin <rondi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Maor Dickman [Wed, 2 Sep 2020 13:49:52 +0000 (16:49 +0300)]
net/mlx5e: Fix endianness when calculating pedit mask first bit
The field mask value is provided in network byte order and has to
be converted to host byte order before calculating pedit mask
first bit.
Fixes:
88f30bbcbaaa ("net/mlx5e: Bit sized fields rewrite support")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>