OSDN Git Service
Michal Nazarewicz [Fri, 25 Jun 2010 14:29:28 +0000 (16:29 +0200)]
USB: gadget: f_mass_storage: stale common->fsg value bug fix
On fsg_unbind the common->fsg pointer was not NULLed if the
unbound fsg_dev instance was the current one. As an effect,
the incorrect pointer was preserved in all further operations
which caused do_set_interface to reference an invalid region.
This commit fixes this by raising an exception in fsg_bind
which will change the common->fsg pointer. This also requires
an wait queue so that the thread in fsg_bind can wait till the
worker thread handles the exception.
This commit removes also a config and new_config fields of
fsg_common as they are no longer needed since fsg can be
used to determine whether function is active or not.
Moreover, this commit removes possible race condition where
the fsg field was modified in both the worker thread and
form various other contexts. This is fixed by replacing
prev_fsg with new_fsg. At this point, fsg is assigned only
in worker thread.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michal Nazarewicz [Fri, 25 Jun 2010 14:29:26 +0000 (16:29 +0200)]
USB: gadget: f_mass_storage: fixed fs descriptors not being updated
The full speed descriptors were copied to the usb_function structure
in the fsg_bind_config function before call to the usb_ep_autoconfig.
The usb_ep_autoconfig was called in fsg_bind using the original
descriptors. In effect copied descriptors were not updated.
This patch changes the copy full speed descriptors after the call to
usb_op_autoconfig is performed. This way, copied full speed
descriptors have updated values.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reported-by: Dries Van Puymbroeck <Dries.VanPuymbroeck@dekimo.com>
Tested-by: Dries Van Puymbroeck <Dries.VanPuymbroeck@dekimo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hema HK [Thu, 24 Jun 2010 17:37:09 +0000 (23:07 +0530)]
USB: musb: Enable the maximum supported burst mode for DMA
Setting MUSB Burst Mode 3 automatically enables support for
lower burst modes (BURST4, BURST8, BURST16 or bursts of unspecified
length). There is no need to set these burst modes based on the
packet size. Also enable the burst mode for both mode1 and mode0.
This is a fix for buggy hardware - having the lower burst modes
enabled can potentially cause lockups of the DMA engine used in
OMAP2/3/4 chips.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mike Frysinger [Thu, 24 Jun 2010 17:37:08 +0000 (23:07 +0530)]
USB: musb: fix Blackfin ulpi stubs
The new ulpi code defines fallback stubs for the Blackfin arch, but does
so incorrectly leading to a build failure:
drivers/usb/musb/musb_core.c:227: error: 'musb_ulpi_read' undeclared here (not in a function)
drivers/usb/musb/musb_core.c:228: error: 'musb_ulpi_write' undeclared here (not in a function)
Tweak the fallback stubs so that they do work as intended.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sergei Shtylyov [Thu, 24 Jun 2010 17:37:07 +0000 (23:07 +0530)]
USB: MUSB: make non-OMAP platforms build with CONFIG_PM=y
Attempt to build MUSB driver with CONFIG_PM=y (e.g. in the OTG mode) on DaVinci
results in these link errors:
drivers/built-in.o: In function `musb_restore_context':
led-triggers.c:(.text+0x714d8): undefined reference to
`musb_platform_restore_context'
drivers/built-in.o: In function `musb_save_context':
led-triggers.c:(.text+0x71788): undefined reference to
`musb_platform_save_context'
This turned out to be caused by commit
9957dd97ec5e98dd334f87ade1d9a0b24d1f86eb
(usb: musb: Fix compile error for omaps for musb_hdrc). Revert it, taking into
account the rename of CONFIG_ARCH_OMAP34XX into CONFIG_ARCH_OMAP3 (which that
commit fixed in a completely inappropriate way) and the recent addition of
OMAP4 support.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sergei Shtylyov [Thu, 24 Jun 2010 17:37:06 +0000 (23:07 +0530)]
USB: musb_core: make disconnect and suspend interrupts work again
Commit
1c25fda4a09e8229800979986ef399401053b46e (usb: musb: handle irqs in the
order dictated by programming guide) forgot to get rid of the old 'STAGE0_MASK'
filter for calling musb_stage0_irq(), so now disconnect and suspend interrupts
are effectively ignored...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 22 Jun 2010 20:14:48 +0000 (16:14 -0400)]
USB: obey the sysfs power/wakeup setting
This patch (as1403) is a partial reversion of an earlier change
(commit
5f677f1d45b2bf08085bbba7394392dfa586fa8e "USB: fix remote
wakeup settings during system sleep"). After hearing from a user, I
realized that remote wakeup should be enabled during system sleep
whenever userspace allows it, and not only if a driver requests it
too.
Indeed, there could be a device with no driver, that does nothing but
generate a wakeup request when the user presses a button. Such a
device should be allowed to do its job.
The problem fixed by the earlier patch -- device generating a wakeup
request for no reason, causing system suspend to abort -- was also
addressed by a later patch ("USB: don't enable remote wakeup by
default", accepted but not yet merged into mainline). The device
won't be able to generate the bogus wakeup requests because it will be
disabled for remote wakeup by default. Hence this reversion will not
re-introduce any old problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jiri Pinkava [Sun, 20 Jun 2010 18:05:52 +0000 (20:05 +0200)]
USB: gadget eth: Fix calculate CRC32 in EEM
CRC should be calculated for Ethernet frame, not for whole recievede EEM data.
This bug shows rarely, because in many times len == skb->len.
Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Axel Lin [Mon, 21 Jun 2010 00:44:17 +0000 (08:44 +0800)]
USB: qcserial: fix a memory leak in qcprobe error path
This patch adds missing kfree(data) before return -ENODEV.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jiri Slaby [Mon, 21 Jun 2010 15:02:40 +0000 (17:02 +0200)]
USB: gadget/printer, fix sleep inside atomic
Stanse found that sleep is called inside atomic context created by
lock_printer_io spinlock in several functions. It's used in process
context only and some functions sleep inside its critical section. As
this is not allowed for spinlocks, switch it to mutex.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Craig W. Nadler <craig@nadler.us>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jiri Slaby [Mon, 21 Jun 2010 15:02:51 +0000 (17:02 +0200)]
USB: isp1362-hcd, fix double lock
Stanse found that isp1362_sw_reset tries to take a isp1362_hcd->lock,
but it is already held in isp1362_hc_stop. Avoid that by introducing
__isp1362_sw_reset which doesn't take the lock and call it from
isp1362_hc_stop. isp1362_sw_reset is then as simple as lock --
__isp1362_sw_reset -- unlock.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Sangorrin [Fri, 18 Jun 2010 06:30:02 +0000 (15:30 +0900)]
USB: serial: ftdi: correct merge conflict with CONTEC id
This patch corrects a problem with the merge of a previous
patch to add the CONTEC identifier.
I believe the merge problem occurred with the commit:
dee5658b482e9e2ac7d6205dc876fc11d4008138
Originally I submitted a patch and then they asked me to order the IDs
and resubmit, so did I. But unfortunately in the end somehow both
patches were merged.
Signed-off-by: Daniel Sangorrin <daniel.sangorrin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 18 Jun 2010 14:16:33 +0000 (10:16 -0400)]
USB: fix oops in usb_sg_init()
This patch (as1401) fixes a bug in usb_sg_init() that can cause an
invalid pointer dereference. An inner loop reuses some local variables
in an unsafe manner, so new variables are introduced.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Vladimir Zapolskiy [Fri, 18 Jun 2010 04:25:00 +0000 (08:25 +0400)]
USB: s3c2410: deactivate endpoints before gadget unbinding
Gadget disconnect must be called before unbinding to avoid races.
The change fixes an oops on g_ether module unregistering.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wolfram Sang [Tue, 15 Jun 2010 10:34:23 +0000 (12:34 +0200)]
USB: ehci-mxc: bail out on transceiver problems
The old code registered the hcd even if there were no transceivers
detected, leading to oopses like this if we try to probe a non-existant
ULPI:
[ 2.730000] mxc-ehci mxc-ehci.0: unable to init transceiver
[ 2.740000] timeout polling for ULPI device
[ 2.740000] timeout polling for ULPI device
[ 2.750000] mxc-ehci mxc-ehci.0: unable to enable vbus on transceiver
[ 2.750000] mxc-ehci mxc-ehci.0: Freescale On-Chip EHCI Host Controller
[ 2.760000] mxc-ehci mxc-ehci.0: new USB bus registered, assigned bus number 2
[ 2.770000] Unhandled fault: external abort on non-linefetch (0x808) at 0xc4876184
[ 2.770000] Internal error: : 808 [#1] PREEMPT
[ 2.770000] last sysfs file:
[ 2.770000] Modules linked in:
[ 2.770000] CPU: 0 Not tainted (2.6.33.5 #5)
[ 2.770000] PC is at ehci_hub_control+0x4d4/0x8f8
[ 2.770000] LR is at ehci_mxc_setup+0xbc/0xdc
[ 2.770000] pc : [<
c0196dfc>] lr : [<
c019bc8c>] psr:
00000093
[ 2.770000] sp :
c3815e40 ip :
00000001 fp :
60000013
[ 2.770000] r10:
c4876184 r9 :
00000000 r8 :
c3814000
[ 2.770000] r7 :
c391d2cc r6 :
00000001 r5 :
00000001 r4 :
00000000
[ 2.770000] r3 :
80000000 r2 :
00000007 r1 :
80000000 r0 :
c4876184
[ 2.770000] Flags: nzcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 2.770000] Control:
0005317f Table:
a0004000 DAC:
00000017
[ 2.770000] Process swapper (pid: 1, stack limit = 0xc3814270)
...
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable <stable@kernel.org>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wolfram Sang [Tue, 15 Jun 2010 10:34:22 +0000 (12:34 +0200)]
USB: otg/ulpi: bail out on read errors
otg_read may return errnos, so bail out correctly to prevent bogus
ID-numbers.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Daniel Mack <daniel@caiaq.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Maulik Mankad [Tue, 15 Jun 2010 09:10:27 +0000 (14:40 +0530)]
usb: musb: Fix a bug by making suspend interrupt available in device mode
As a part of aligning the ISR code for MUSB with the specs, the
ISR code was re-written.
See Commit
1c25fda4a09e8229800979986ef399401053b46e (usb: musb: handle
irqs in the order dictated by programming guide)
With this the suspend interrupt came accidently under CONFIG_USB_MUSB_HDRC_HCD.
The fix brings suspend interrupt handling outside
CONFIG_USB_MUSB_HDRC_HCD.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nobuhiro Iwamatsu [Mon, 7 Jun 2010 07:55:56 +0000 (16:55 +0900)]
USB: r8a66597: Fix failure in change of status
In the change by
749da5f82fe33ff68dd4aa1a5e35cd9aa6246dab,
The change in the status when the USB device is connected is wrong.
Therefore, the device is not recognized.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Paul Mundt" <lethal@linux-sh.org>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Thu, 10 Jun 2010 19:25:28 +0000 (12:25 -0700)]
USB: xHCI: Fix bug in link TRB activation change.
Commit
6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for
control transfers. The patch was supposed to change when the link TRBs at
the end of each ring segment were given to the hardware. If a transfer
descriptor (TD) ended just before the link TRB, the code wouldn't give
back the link TRB to the hardware; instead it would be given back in
prepare_ring() just before the next TD was enqueued at the top of the
ring.
Unfortunately, the code relied on checking the chain bit of the TRB to
determine whether the TD ended just before the link TRB. It assumed that
the ring enqueuing code would call prepare_ring() before enqueuing the
next TD. However, control transfers are made of multiple TDs, and
prepare_ring() is only called once before enqueuing two or three TDs.
If the first or second TD of the control transfer ended just before the
link TRB, then the code in inc_enq() would not move the enqueue pointer
past the link TRB, and the link TRB would get overwritten. This would
cause the xHCI driver to start writing to memory past the ring segment,
and eventually the system would crash or hang.
The fix is to add a flag to inc_enq() that says whether the caller will
enqueue more TDs before calling prepare_ring(). If the chain bit is
cleared (meaning this is the last TRB in a TD), and the caller will not
enqueue more TDs, then we defer giving back the link TRB.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michal Nazarewicz [Mon, 14 Jun 2010 08:43:34 +0000 (10:43 +0200)]
USB: gadget: g_fs: possible invalid pointer reference bug fixed
During __gfs_do_config() some invalid pointers may be left
in usb_configuration::interfaces array from previous calls
to the __gfs_do_config() for the same configuration. This
will always happen if an user space function which has
a fewer then the last user space function registers itself.
Composite's set_config() function that a pointer after the
last interface in usb_configuration::interface is NULL
unless the array is full.
This patch makes the __gfs_do_config() make sure that if the
usb_configuration::interface is not full then a pointer
after the last interface is NULL.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jon Povey [Mon, 14 Jun 2010 10:42:10 +0000 (19:42 +0900)]
USB: g_serial: fix tty cleanup on unload
Call put_tty_driver() in cleanup function, to fix Oops when trying to open
gadget serial char device after module unload.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jon Povey [Mon, 14 Jun 2010 10:41:04 +0000 (19:41 +0900)]
USB: g_serial: don't set low_latency flag
No longer set low_latency flag as it causes this warning backtrace:
WARNING: at kernel/mutex.c:207 __mutex_lock_slowpath+0x6c/0x288()
Fix associated locking and wakeups.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Cc: Maulik Mankad <x0082077@ti.com>
Cc: stable <stable@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds [Mon, 28 Jun 2010 05:56:32 +0000 (22:56 -0700)]
Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
md/raid5: don't include 'spare' drives when reshaping to fewer devices.
md/raid5: add a missing 'continue' in a loop.
md/raid5: Allow recovered part of partially recovered devices to be in-sync
md/raid5: More careful check for "has array failed".
md: Don't update ->recovery_offset when reshaping an array to fewer devices.
md/raid5: avoid oops when number of devices is reduced then increased.
md: enable raid4->raid0 takeover
md: clear layout after ->raid0 takeover
md: fix raid10 takeover: use new_layout for setup_conf
md: fix handling of array level takeover that re-arranges devices.
md: raid10: Fix null pointer dereference in fix_read_error()
Restore partition detection of newly created md arrays.
Linus Torvalds [Sun, 27 Jun 2010 18:33:44 +0000 (11:33 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tj/percpu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: fix first chunk match in per_cpu_ptr_to_phys()
percpu: fix trivial bugs in pcpu_build_alloc_info()
Linus Torvalds [Sun, 27 Jun 2010 18:28:02 +0000 (11:28 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (52 commits)
phylib: Add autoload support for the LXT973 phy.
ISDN: hysdn, fix potential NULL dereference
vxge: fix memory leak in vxge_alloc_msix() error path
isdn/gigaset: correct CAPI connection state storage
isdn/gigaset: encode HLC and BC together
isdn/gigaset: correct CAPI DATA_B3 Delivery Confirmation
isdn/gigaset: correct CAPI voice connection encoding
isdn/gigaset: honor CAPI application's buffer size request
cpmac: do not leak struct net_device on phy_connect errors
smc91c92_cs: fix the problem that lan & modem does not work simultaneously
ipv6: fix NULL reference in proxy neighbor discovery
Bluetooth: Bring back var 'i' increment
xfrm: check bundle policy existance before dereferencing it
sky2: enable rx/tx in sky2_phy_reinit()
cnic: Disable statistics initialization for eth clients that do not support statistics
net: add dependency on fw class module to qlcnic and netxen_nic
snmp: fix SNMP_ADD_STATS()
hso: remove setting of low_latency flag
udp: Fix bogus UFO packet generation
lasi82596: fix netdev_mc_count conversion
...
Linus Torvalds [Sun, 27 Jun 2010 16:04:02 +0000 (09:04 -0700)]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFSv4: Fix an embarassing typo in encode_attrs()
NFSv4: Ensure that /proc/self/mountinfo displays the minor version number
NFSv4.1: Ensure that we initialise the session when following a referral
SUNRPC: Fix a re-entrancy bug in xs_tcp_read_calldir()
nfs4 use mandatory attribute file type in nfs4_get_root
Linus Torvalds [Sun, 27 Jun 2010 15:18:20 +0000 (08:18 -0700)]
Merge branch 'sh/for-linus' of git://git./linux/kernel/git/lethal/sh-2.6
* 'sh/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
clocksource: sh_cmt: Fix up bogus shift value.
arch/sh/mm: Eliminate a double lock
sh: Fix up IORESOURCE_PCI_FIXED usage in pcibios_fixup_device_resources().
sh: remove duplicated #include
Linus Torvalds [Sun, 27 Jun 2010 15:03:00 +0000 (08:03 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
MAINTAINERS - Add an entry for the input MT protocol
Input: wacom - fix serial number handling on Cintiq 21UX2
Input: fixup X86_MRST selects
Input: sysrq - fix "stuck" SysRq mode
Input: ad7877 - fix spi word size to 16 bit
Input: pcf8574_keypad - fix off by one in pcf8574_kp_irq_handler()
Linus Torvalds [Sun, 27 Jun 2010 14:50:47 +0000 (07:50 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
ext3: update ctime when changing the file's permission by setfacl
ext2: update ctime when changing the file's permission by setfacl
Linus Torvalds [Sun, 27 Jun 2010 14:49:45 +0000 (07:49 -0700)]
Merge branch 'virtio' of git://git./linux/kernel/git/rusty/linux-2.6
* 'virtio' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6:
virtio-pci: disable msi at startup
virtio: return ENOMEM on out of memory
Linus Torvalds [Sun, 27 Jun 2010 14:41:04 +0000 (07:41 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/PM: Do not use native PCIe PME by default
Linus Torvalds [Sun, 27 Jun 2010 14:39:57 +0000 (07:39 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: usb/endpoint, fix dangling pointer use
ALSA: asihpi - Get rid of incorrect "long" types and casts.
ASoC: DaVinci: Fix McASP hardware FIFO configuration
ALSA: hda - Fix line-in for mb5 model MacBook (Pro) 5,1 / 5,2
ALSA: usb-audio: fix UAC2 control value queries
ALSA: usb-audio: parse UAC2 sample rate ranges correctly
ALSA: usb-audio: fix control messages for USB_RECIP_INTERFACE
ALSA: usb-audio: add check for faulty clock in parse_audio_format_rates_v2()
ALSA: hda - Don't check capture source mixer if no ADC is available
Linus Torvalds [Sun, 27 Jun 2010 14:39:38 +0000 (07:39 -0700)]
Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (k8temp) Bypass core swapping on single-core processors
hwmon: (i5k_amb) Fix sysfs attribute for lockdep
hwmon: (k10temp) Do not blacklist known working CPU models
Linus Torvalds [Sun, 27 Jun 2010 14:38:20 +0000 (07:38 -0700)]
Merge git://git./linux/kernel/git/wim/linux-2.6-watchdog
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
watchdog: at32ap700x_wdt: register misc device last in probe() function
watchdog: [PATCH 3/3] imx2_wdt: fix section mismatch
Linus Torvalds [Sun, 27 Jun 2010 14:37:51 +0000 (07:37 -0700)]
Merge git://git.infradead.org/iommu-2.6
* git://git.infradead.org/iommu-2.6:
intel-iommu: Force-disable IOMMU for iGFX on broken Cantiga revisions.
intel-iommu: Fix double lock in get_domain_for_dev()
intel-iommu: Fix reference by physical address in intel_iommu_attach_device()
Linus Torvalds [Sun, 27 Jun 2010 14:36:16 +0000 (07:36 -0700)]
Merge branch 'for-linus' of git://gitorious.org/linux-omap-dss2/linux
* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux:
OMAP: OMAPFB: fix rfbi.c compile error
OMAPFB: LCDC: change update_mode to DISABLED when going suspend
Linus Torvalds [Sun, 27 Jun 2010 14:34:02 +0000 (07:34 -0700)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
MAINTAINERS: change mailing list address for CIFS
cifs: remove bogus first_time check in NTLMv2 session setup code
cifs: don't call cifs_new_fileinfo unless cifs_open succeeds
cifs: don't ignore cifs_posix_open_inode_helper return value
cifs: clean up arguments to cifs_open_inode_helper
cifs: pass instantiated filp back after open call
cifs: move cifs_new_fileinfo call out of cifs_posix_open
cifs: implement drop_inode superblock op
cifs: don't attempt busy-file rename unless it's in same directory
Linus Torvalds [Sun, 27 Jun 2010 14:30:25 +0000 (07:30 -0700)]
Merge branch 'merge' of git://git.secretlab.ca/git/linux-2.6
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
powerpc/5200: fix lite5200 ethernet phy address
powerpc/5200: Fix build error in sound code.
powerpc/5200: fix oops during going to standby
powerpc/5200: add lite5200 onboard I2C eeprom and flash
maintainers: Add git trees for SPI and device tree
of: Drop properties with "/" in their name
Linus Torvalds [Sun, 27 Jun 2010 14:29:19 +0000 (07:29 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mattst88/alpha-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: Fix de2104x driver failing to readout MAC address correctly
alpha: Detect Super IO chip, no IDE on Avanti, enable EPP19
alpha: fix pci_mmap_resource API breakage
alpha: fix __arch_hweight32 typo
Linus Torvalds [Sun, 27 Jun 2010 14:15:53 +0000 (07:15 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix mpic_resume on early G5 macs
powerpc: rtas_flash needs to use rtas_data_buf
powerpc: Unconditionally enabled irq stacks
powerpc/kexec: Wait for online/possible CPUs only.
powerpc: Disable CONFIG_SYSFS_DEPRECATED
powerpc/boot: Remove addRamdisk.c since it is now unused
powerpc: Move kdump default base address to 64MB on 64bit
powerpc: Remove dead CONFIG_HIGHPTE
powerpc/fsl-booke: Move loadcam_entry back to asm code to fix SMP ftrace
powerpc/fsl-booke: Fix InstructionTLBError execute permission check
Linus Torvalds [Sun, 27 Jun 2010 14:13:13 +0000 (07:13 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
TPM: ReadPubEK output struct fix
Linus Torvalds [Sun, 27 Jun 2010 14:05:02 +0000 (07:05 -0700)]
Merge branch 'rc-fixes' of git://git./linux/kernel/git/mmarek/kbuild-2.6
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
kbuild: fix LOCALVERSION handling to match description
kbuild: Fix modpost segfault
Linus Torvalds [Sun, 27 Jun 2010 14:03:12 +0000 (07:03 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI / PM: Do not enable GPEs for system wakeup in advance
ACPICA: Truncate I/O addresses to 16 bits for Windows compatibility
ACPICA: Limit maximum time for Sleep() operator
ACPICA: Fix namestring associated with AE_NO_HANDLER exception
ACPI / ACPICA: Fix sysfs GPE interface
ACPI / ACPICA: Fix GPE initialization
ACPI / ACPICA: Avoid writing full enable masks to GPE registers
ACPI / ACPICA: Fix low-level GPE manipulation code
ACPI / ACPICA: Use helper function for computing GPE masks
ACPI / ACPICA: Do not attempt to disable GPE when installing handler
ACPI: Disable Vista compatibility for Sony VGN-NS50B_L
ACPI: fan: fix unbalanced code block
ACPI: Store NVS state even when entering suspend to RAM
suspend: Move NVS save/restore code to generic suspend functionality
ACPI: Do not try to set up acpi processor stuff on cores exceeding maxcpus=
ACPI: acpi_pad: Don't needlessly mark LAPIC unstable
Dan Carpenter [Fri, 11 Jun 2010 16:30:05 +0000 (17:30 +0100)]
KEYS: Propagate error code instead of returning -EINVAL
This is from a Smatch check I'm writing.
strncpy_from_user() returns -EFAULT on error so the first change just
silences a warning but doesn't change how the code works.
The other change is a bug fix because install_thread_keyring_to_cred()
can return a variety of errors such as -EINVAL, -EEXIST, -ENOMEM or
-EKEYREVOKED.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Woodhouse [Tue, 22 Jun 2010 02:38:13 +0000 (02:38 +0000)]
phylib: Add autoload support for the LXT973 phy.
Commit
e13647c1 (phylib: Add support for the LXT973 phy.) added a new ID
but neglected to also add it to the MODULE_DEVICE_TABLE.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Slaby [Tue, 22 Jun 2010 01:41:36 +0000 (01:41 +0000)]
ISDN: hysdn, fix potential NULL dereference
Stanse found that lp is dereferenced earlier than checked for being
NULL in hysdn_rx_netpkt. Move the initialization below the test.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Thu, 24 Jun 2010 04:13:44 +0000 (04:13 +0000)]
vxge: fix memory leak in vxge_alloc_msix() error path
When pci_enable_msix() returned ret<0, entries and vxge_entries were leaked.
While at it, use the centralized exit idiom in the function.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tilman Schmidt [Mon, 21 Jun 2010 13:55:20 +0000 (13:55 +0000)]
isdn/gigaset: correct CAPI connection state storage
CAPI applications can handle several connections in parallel,
so one connection state per application isn't sufficient.
Store the connection state in the channel structure instead.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tilman Schmidt [Mon, 21 Jun 2010 13:55:05 +0000 (13:55 +0000)]
isdn/gigaset: encode HLC and BC together
Adapt to buggy device firmware which accepts setting HLC only in the
same command line as BC, by encoding HLC and BC in a single command
if both are specified, and rejecting HLC without BC.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tilman Schmidt [Mon, 21 Jun 2010 13:54:50 +0000 (13:54 +0000)]
isdn/gigaset: correct CAPI DATA_B3 Delivery Confirmation
The Gigaset CAPI driver handled all DATA_B3_REQ messages as if the
Delivery Confirmation flag bit was set, delaying the emission of the
DATA_B3_CONF reply until the data was actually transmitted. Some
CAPI applications (notably Asterisk) aren't happy with that
behaviour. Change it to actually evaluate the Delivery Confirmation
flag as described the CAPI specification.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tilman Schmidt [Mon, 21 Jun 2010 13:54:35 +0000 (13:54 +0000)]
isdn/gigaset: correct CAPI voice connection encoding
Make the Gigaset CAPI driver select L2_VOICE (AT^SBPR=2) as the
layer 2 encoding for transparent connections, like the ISDN4Linux
variant. L2_BITSYNC (AT^SBPR=0) mutes internal connections and
distorts external ones.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tilman Schmidt [Mon, 21 Jun 2010 13:54:19 +0000 (13:54 +0000)]
isdn/gigaset: honor CAPI application's buffer size request
Fix the Gigaset CAPI driver to limit the length of a connection's
payload data receive buffers to the corresponding CAPI application's
data buffer size, as some real-life CAPI applications tend to be
rather unhappy if they receive bigger data blocks than requested.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sun, 20 Jun 2010 22:07:48 +0000 (22:07 +0000)]
cpmac: do not leak struct net_device on phy_connect errors
If the call to phy_connect fails, we will return directly instead of freeing
the previously allocated struct net_device.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Ken Kawasaki [Sat, 19 Jun 2010 15:24:27 +0000 (15:24 +0000)]
smc91c92_cs: fix the problem that lan & modem does not work simultaneously
smc91c92_cs:
Fix the problem that lan & modem does not work simultaneously
in the Megahertz multi-function card.
We need to write MEGAHERTZ_ISR to retrigger interrupt.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Mon, 21 Jun 2010 11:00:13 +0000 (11:00 +0000)]
ipv6: fix NULL reference in proxy neighbor discovery
The addition of TLLAO option created a kernel OOPS regression
for the case where neighbor advertisement is being sent via
proxy path. When using proxy, ipv6_get_ifaddr() returns NULL
causing the NULL dereference.
Change causing the bug was:
commit
f7734fdf61ec6bb848e0bafc1fb8bad2c124bb50
Author: Octavian Purdila <opurdila@ixiacom.com>
Date: Fri Oct 2 11:39:15 2009 +0000
make TLLAO option for NA packets configurable
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo F. Padovan [Fri, 18 Jun 2010 14:24:00 +0000 (14:24 +0000)]
Bluetooth: Bring back var 'i' increment
commit
ff6e2163f28a1094fb5ca5950fe2b43c3cf6bc7a accidentally added a
regression on the bnep code. Fixing it.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Henrik Rydberg [Fri, 25 Jun 2010 02:10:40 +0000 (19:10 -0700)]
MAINTAINERS - Add an entry for the input MT protocol
This patch adds a maintainer for the input multitouch (MT) protocol,
such that get_maintainer.pl selects it whenever an MT event is present
in the patch.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Miao Xie [Thu, 27 May 2010 08:28:40 +0000 (16:28 +0800)]
ext3: update ctime when changing the file's permission by setfacl
ext3 didn't update the ctime of the file when its permission was changed.
Steps to reproduce:
# touch aaa
# stat -c %Z aaa
1275289822
# setfacl -m 'u::x,g::x,o::x' aaa
# stat -c %Z aaa
1275289822 <- unchanged
But, according to the spec of the ctime, ext3 must update it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Wed, 2 Jun 2010 14:26:51 +0000 (16:26 +0200)]
ext2: update ctime when changing the file's permission by setfacl
ext2 didn't update the ctime of the file when its permission was changed.
Steps to reproduce:
# touch aaa
# stat -c %Z aaa
1275289822
# setfacl -m 'u::x,g::x,o::x' aaa
# stat -c %Z aaa
1275289822 <- unchanged
But, according to the spec of the ctime, ext2 must update it.
Port of ext3 patch by Miao Xie <miaox@cn.fujitsu.com>.
Signed-off-by: Jan Kara <jack@suse.cz>
Timo Teräs [Thu, 24 Jun 2010 21:35:00 +0000 (14:35 -0700)]
xfrm: check bundle policy existance before dereferencing it
Fix the bundle validation code to not assume having a valid policy.
When we have multiple transformations for a xfrm policy, the bundle
instance will be a chain of bundles with only the first one having
the policy reference. When policy_genid is bumped it will expire the
first bundle in the chain which is equivalent of expiring the whole
chain.
Reported-bisected-and-tested-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
NeilBrown [Thu, 17 Jun 2010 07:48:26 +0000 (17:48 +1000)]
md/raid5: don't include 'spare' drives when reshaping to fewer devices.
There are few situations where it would make any sense to add a spare
when reducing the number of devices in an array, but it is
conceivable: A 6 drive RAID6 with two missing devices could be
reshaped to a 5 drive RAID6, and a spare could become available
just in time for the reshape, but not early enough to have been
recovered first. 'freezing' recovery can make this easy to
do without any races.
However doing such a thing is a bad idea. md will not record the
partially-recovered state of the 'spare' and when the reshape
finished it will think that the spare is still spare.
Easiest way to avoid this confusion is to simply disallow it.
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Thu, 17 Jun 2010 07:41:03 +0000 (17:41 +1000)]
md/raid5: add a missing 'continue' in a loop.
As the comment says, the tail of this loop only applies to devices
that are not fully in sync, so if In_sync was set, we should avoid
the rest of the loop.
This bug will hardly ever cause an actual problem. The worst it
can do is allow an array to be assembled that is dirty and degraded,
which is not generally a good idea (without warning the sysadmin
first).
This will only happen if the array is RAID4 or a RAID5/6 in an
intermediate state during a reshape and so has one drive that is
all 'parity' - no data - while some other device has failed.
This is certainly possible, but not at all common.
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Thu, 17 Jun 2010 07:25:21 +0000 (17:25 +1000)]
md/raid5: Allow recovered part of partially recovered devices to be in-sync
During a recovery of reshape the early part of some devices might be
in-sync while the later parts are not.
We we know we are looking at an early part it is good to treat that
part as in-sync for stripe calculations.
This is particularly important for a reshape which suffers device
failure. Treating the data as in-sync can mean the difference between
data-safety and data-loss.
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Wed, 16 Jun 2010 07:17:53 +0000 (17:17 +1000)]
md/raid5: More careful check for "has array failed".
When we are reshaping an array, the device failure combinations
that cause us to decide that the array as failed are more subtle.
In particular, any 'spare' will be fully in-sync in the section
of the array that has already been reshaped, thus failures that
affect only that section are less critical.
So encode this subtlety in a new function and call it as appropriate.
The case that showed this problem was a 4 drive RAID5 to 8 drive RAID6
conversion where the last two devices failed.
This resulted in:
good good good good incomplete good good failed failed
while converting a 5-drive RAID6 to 8 drive RAID5
The incomplete device causes the whole array to look bad,
bad as it was actually good for the section that had been
converted to 8-drives, all the data was actually safe.
Reported-by: Terry Morris <tbmorris@tbmorris.com>
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Wed, 16 Jun 2010 07:01:25 +0000 (17:01 +1000)]
md: Don't update ->recovery_offset when reshaping an array to fewer devices.
When an array is reshaped to have fewer devices, the reshape proceeds
from the end of the devices to the beginning.
If a device happens to be non-In_sync (which is possible but rare)
we would normally update the ->recovery_offset as the reshape
progresses. However that would be wrong as the recover_offset records
that the early part of the device is in_sync, while in fact it would
only be the later part that is in_sync, and in any case the offset
number would be measured from the wrong end of the device.
Relatedly, if after a reshape a spare is discovered to not be
recoverred all the way to the end, not allow spare_active
to incorporate it in the array.
This becomes relevant in the following sample scenario:
A 4 drive RAID5 is converted to a 6 drive RAID6 in a combined
operation.
The RAID5->RAID6 conversion will cause a 5 drive to be included as a
spare, then the 5drive -> 6drive reshape will effectively rebuild that
spare as it progresses. The 6th drive is treated as in_sync the whole
time as there is never any case that we might consider reading from
it, but must not because there is no valid data.
If we interrupt this reshape part-way through and reverse it to return
to a 5-drive RAID6 (or event a 4-drive RAID5), we don't want to update
the recovery_offset - as that would be wrong - and we don't want to
include that spare as active in the 5-drive RAID6 when the reversed
reshape completed and it will be mostly out-of-sync still.
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Wed, 16 Jun 2010 06:45:16 +0000 (16:45 +1000)]
md/raid5: avoid oops when number of devices is reduced then increased.
The entries in the stripe_cache maintained by raid5 are enlarged
when we increased the number of devices in the array, but not
shrunk when we reduce the number of devices.
So if entries are added after reducing the number of devices, we
much ensure to initialise the whole entry, not just the part that
is currently relevant. Otherwise if we enlarge the array again,
we will reference uninitialised values.
As grow_buffers/shrink_buffer now want to use a count that is stored
explicity in the raid_conf, they should get it from there rather than
being passed it as a parameter.
Signed-off-by: NeilBrown <neilb@suse.de>
Maciej Trela [Wed, 16 Jun 2010 10:56:12 +0000 (11:56 +0100)]
md: enable raid4->raid0 takeover
Only level 5 with layout=PARITY_N can be taken over to raid0 now.
Lets allow level 4 either.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Maciej Trela [Wed, 16 Jun 2010 10:55:14 +0000 (11:55 +0100)]
md: clear layout after ->raid0 takeover
After takeover from raid5/10 -> raid0 mddev->layout is not cleared.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Maciej Trela [Wed, 16 Jun 2010 10:46:29 +0000 (11:46 +0100)]
md: fix raid10 takeover: use new_layout for setup_conf
Use mddev->new_layout in setup_conf.
Also use new_chunk, and don't set ->degraded in takeover(). That
gets set in run()
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Tue, 15 Jun 2010 08:36:03 +0000 (09:36 +0100)]
md: fix handling of array level takeover that re-arranges devices.
Most array level changes leave the list of devices largely unchanged,
possibly causing one at the end to become redundant.
However conversions between RAID0 and RAID10 need to renumber
all devices (except 0).
This renumbering is currently being done in the ->run method when the
new personality takes over. However this is too late as the common
code in md.c might already have invalidated some of the devices if
they had a ->raid_disk number that appeared to high.
Moving it into the ->takeover method is too early as the array is
still active at that time and wrong ->raid_disk numbers could cause
confusion.
So add a ->new_raid_disk field to mdk_rdev_s and use it to communicate
the new raid_disk number.
Now the common code knows exactly which devices need to be renumbered,
and which can be invalidated, and can do it all at a convenient time
when the array is suspend.
It can also update some symlinks in sysfs which previously were not be
updated correctly.
Reported-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Prasanna S. Panchamukhi [Thu, 24 Jun 2010 03:31:03 +0000 (13:31 +1000)]
md: raid10: Fix null pointer dereference in fix_read_error()
Such NULL pointer dereference can occur when the driver was fixing the
read errors/bad blocks and the disk was physically removed
causing a system crash. This patch check if the
rcu_dereference() returns valid rdev before accessing it in fix_read_error().
Cc: stable@kernel.org
Signed-off-by: Prasanna S. Panchamukhi <prasanna.panchamukhi@riverbed.com>
Signed-off-by: Rob Becker <rbecker@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Thu, 24 Jun 2010 03:31:03 +0000 (13:31 +1000)]
Restore partition detection of newly created md arrays.
Commit
b821eaa572fd737faaf6928ba046e571526c36c6 broke partition
detection for md arrays.
The logic was almost right. However if revalidate_disk is called
when the device is not yet open, bdev->bd_disk won't be set, so the
flush_disk() Call will not set bd_invalidated.
So when md_open is called we still need to ensure that
->bd_invalidated gets set. This is easily done with a call to
check_disk_size_change in the place where the offending commit removed
check_disk_change. At the important times, the size will have changed
from 0 to non-zero, so check_disk_size_change will set bd_invalidated.
Tested-by: Duncan <1i5t5.duncan@cox.net>
Reported-by: Duncan <1i5t5.duncan@cox.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Brandon Philips [Wed, 16 Jun 2010 16:21:58 +0000 (16:21 +0000)]
sky2: enable rx/tx in sky2_phy_reinit()
sky2_phy_reinit is called by the ethtool helpers sky2_set_settings,
sky2_nway_reset and sky2_set_pauseparam when netif_running.
However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and
GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to
stop working:
$ ethtool -r eth0
$ ethtool -A eth0 autoneg off
Fix this issue by enabling Rx/Tx after running sky2_phy_init in
sky2_phy_reinit.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Tested-by: Brandon Philips <bphilips@suse.de>
Cc: stable@kernel.org
Tested-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Layton [Sun, 6 Jun 2010 12:05:58 +0000 (08:05 -0400)]
MAINTAINERS: change mailing list address for CIFS
We're moving the mailing list to linux-cifs@vger.kernel.org.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Dmitry Kravkov [Wed, 23 Jun 2010 18:57:09 +0000 (11:57 -0700)]
cnic: Disable statistics initialization for eth clients that do not support statistics
Disable statistics initialization for eth clients that do not support
statistics. This prevents memory corruption on bnx2x hw.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Anirban Chakraborty [Wed, 23 Jun 2010 18:49:42 +0000 (11:49 -0700)]
net: add dependency on fw class module to qlcnic and netxen_nic
netxen_nic and qlcnic driver depends on firmware_class module.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 23 Jun 2010 00:32:03 +0000 (00:32 +0000)]
snmp: fix SNMP_ADD_STATS()
commit
aa2ea0586d9d (tcp: fix outsegs stat for TSO segments) incorrectly
assumed SNMP_ADD_STATS() was used from BH context.
Fix this using mib[!in_softirq()] instead of mib[0]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael S. Tsirkin [Thu, 24 Jun 2010 04:49:06 +0000 (22:49 -0600)]
virtio-pci: disable msi at startup
virtio-pci resets the device at startup by writing to the status
register, but this does not clear the pci config space,
specifically msi enable status which affects register
layout.
This breaks things like kdump when they try to use e.g. virtio-blk.
Fix by forcing msi off at startup. Since pci.c already has
a routine to do this, we export and use it instead of duplicating code.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Michael S. Tsirkin [Thu, 10 Jun 2010 15:16:11 +0000 (18:16 +0300)]
virtio: return ENOMEM on out of memory
add_buf returns ring size on out of memory,
this is not what devices expect.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org # .34.x
Ping Cheng [Tue, 22 Jun 2010 18:21:34 +0000 (11:21 -0700)]
Input: wacom - fix serial number handling on Cintiq 21UX2
Cintiq 21UX2 added 8 more bits for the tool serial number and more
buttons for the expresskey. We did not enable them properly in the
last patch.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Randy Dunlap [Fri, 18 Jun 2010 05:31:17 +0000 (22:31 -0700)]
Input: fixup X86_MRST selects
Some of the recent X86_MRST additions make some "select"s
conditional on X86_MRST but missed some related kconfig symbols,
causing:
drivers/built-in.o: In function `ps2_end_command':
(.text+0x257ab2): undefined reference to `i8042_check_port_owner'
drivers/built-in.o: In function `ps2_end_command':
(.text+0x257ae1): undefined reference to `i8042_unlock_chip'
drivers/built-in.o: In function `ps2_begin_command':
(.text+0x257b40): undefined reference to `i8042_check_port_owner'
drivers/built-in.o: In function `ps2_begin_command':
(.text+0x257b6f): undefined reference to `i8042_lock_chip'
when SERIO_I8042=m, SERIO_LIBPS2=y, KEYBOARD_ATKBD=y.
We need to make i8042 dependant upon !X86_MRST and allow deselecting
atkbd on Moorestown even when !CONFIG_EMBEDDED.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Dmitry Torokhov [Tue, 22 Jun 2010 18:32:04 +0000 (11:32 -0700)]
Merge commit 'v2.6.35-rc3' into for-linus
David S. Miller [Tue, 22 Jun 2010 17:54:12 +0000 (10:54 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6
Trond Myklebust [Tue, 22 Jun 2010 12:52:39 +0000 (08:52 -0400)]
NFSv4: Fix an embarassing typo in encode_attrs()
Apparently, we have never been able to set the atime correctly from the
NFSv4 client.
Reported-by: 小倉一夫 <ka-ogura@bd6.so-net.ne.jp>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Trond Myklebust [Fri, 18 Jun 2010 16:23:58 +0000 (12:23 -0400)]
NFSv4: Ensure that /proc/self/mountinfo displays the minor version number
Currently, we do not display the minor version mount parameter in the
/proc mount info.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Trond Myklebust [Thu, 17 Jun 2010 15:45:12 +0000 (11:45 -0400)]
NFSv4.1: Ensure that we initialise the session when following a referral
Put the code that is common to both the referral and ordinary mount cases
into a common helper routine.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Wed, 16 Jun 2010 17:57:32 +0000 (13:57 -0400)]
SUNRPC: Fix a re-entrancy bug in xs_tcp_read_calldir()
If the attempt to read the calldir fails, then instead of storing the read
bytes, we currently discard them. This leads to a garbage final result when
upon re-entry to the same routine, we read the remaining bytes.
Fixes the regression in bugzilla number 16213. Please see
https://bugzilla.kernel.org/show_bug.cgi?id=16213
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Andy Adamson [Wed, 16 Jun 2010 13:51:02 +0000 (09:51 -0400)]
nfs4 use mandatory attribute file type in nfs4_get_root
S_ISDIR(fsinfo.fattr->mode) checks the file type rather than the mode bits,
so we should be checking for the NFS_ATTR_FATTR_TYPE fattr property.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Filip Aben [Tue, 22 Jun 2010 17:10:35 +0000 (10:10 -0700)]
hso: remove setting of low_latency flag
This patch removes the setting of the low_latency flag.
tty_flip_buffer_push() is occasionally being called in irq context, which
causes a hang if the low_latency flag is set.
Removing the low_latency flag only seems to impact the flush to ldisc,
which will now be put on a workqueue.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Mundt [Tue, 22 Jun 2010 07:41:31 +0000 (16:41 +0900)]
clocksource: sh_cmt: Fix up bogus shift value.
The previous CMT fixup accidentally copied in the TMU shift value, reset
this back to its original value while preserving the TMU fix.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Herbert Xu [Tue, 15 Jun 2010 01:52:25 +0000 (01:52 +0000)]
udp: Fix bogus UFO packet generation
It has been reported that the new UFO software fallback path
fails under certain conditions with NFS. I tracked the problem
down to the generation of UFO packets that are smaller than the
MTU. The software fallback path simply discards these packets.
This patch fixes the problem by not generating such packets on
the UFO path.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Helge Deller [Mon, 21 Jun 2010 20:50:18 +0000 (13:50 -0700)]
lasi82596: fix netdev_mc_count conversion
Fix commit
4cd24eaf0 (net: use netdev_mc_count and netdev_mc_empty when
appropriate)
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ralf Baechle [Mon, 21 Jun 2010 03:44:50 +0000 (03:44 +0000)]
NET: MIPSsim: Fix modpost warning.
$ make CONFIG_DEBUG_SECTION_MISMATCH=y
[...]
WARNING: drivers/net/built-in.o(.data+0x0): Section mismatch in reference from the variable mipsnet_driver to the function .init.text:mipsnet_probe()
The variable mipsnet_driver references
the function __init mipsnet_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
[...]
Fixed by making mipsnet_probe __devinit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/mipsnet.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai [Mon, 21 Jun 2010 15:08:41 +0000 (17:08 +0200)]
Merge branch 'fix/misc' into for-linus
Jiri Slaby [Mon, 21 Jun 2010 15:03:21 +0000 (17:03 +0200)]
ALSA: usb/endpoint, fix dangling pointer use
Stanse found that in snd_usb_parse_audio_endpoints, there is a
dangling pointer dereference. When snd_usb_parse_audio_format fails,
fp is freed, and continue invoked. On the next loop, there is
"fp && fp->altsetting == 1 && fp->channels == 1" test, but fp is set
from the last iteration (but is bogus) and thus ilegally dereferenced.
Set fp to NULL before "continue".
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Julia Lawall [Sun, 20 Jun 2010 11:24:54 +0000 (11:24 +0000)]
arch/sh/mm: Eliminate a double lock
The function begins and ends with a read_lock. The latter is changed to a
read_unlock.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@locked@
expression E1;
position p;
@@
read_lock(E1@p,...);
@r exists@
expression x <= locked.E1;
expression locked.E1;
expression E2;
identifier lock;
position locked.p,p1,p2;
@@
*lock@p1 (E1@p,...);
... when != E1
when != \(x = E2\|&x\)
*lock@p2 (E1,...);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Takashi Iwai [Sun, 20 Jun 2010 08:38:19 +0000 (10:38 +0200)]
Merge branch 'fix/misc' into for-linus
Takashi Iwai [Sun, 20 Jun 2010 08:38:14 +0000 (10:38 +0200)]
Merge branch 'fix/asoc' into for-linus
Jean Delvare [Sun, 20 Jun 2010 07:22:32 +0000 (09:22 +0200)]
hwmon: (k8temp) Bypass core swapping on single-core processors
Commit
a2e066bba2aad6583e3ff648bf28339d6c9f0898 introduced core
swapping for CPU models 64 and later. I recently had a report about
a Sempron 3200+, model 95, for which this patch broke temperature
reading. It happens that this is a single-core processor, so the
effect of the swapping was to read a temperature value for a core
that didn't exist, leading to an incorrect value (-49 degrees C.)
Disabling core swapping on singe-core processors should fix this.
Additional comment from Andreas:
The BKDG says
Thermal Sensor Core Select (ThermSenseCoreSel)-Bit 2. This bit
selects the CPU whose temperature is reported in the CurTemp
field. This bit only applies to dual core processors. For
single core processors CPU0 Thermal Sensor is always selected.
k8temp_probe() correctly detected that SEL_CORE can't be used on single
core CPU. Thus k8temp did never update the temperature values stored
in temp[1][x] and -49 degrees was reported. For single core CPUs we
must use the values read into temp[0][x].
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Rick Moritz <rhavin@gmx.net>
Acked-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: stable@kernel.org
KAMEZAWA Hiroyuki [Sun, 20 Jun 2010 07:22:31 +0000 (09:22 +0200)]
hwmon: (i5k_amb) Fix sysfs attribute for lockdep
i5k_amb.ko uses dynamically allocated memory (by kmalloc) for
attributes passed to sysfs. So, sysfs_attr_init() should be called
for working happy with lockdep.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org [2.6.34 only]