block: fix an integer overflow in logical block size

commit ad6bf88a6c19a39fb3b0045d78ea880325dfcf15 upstream.

Logical block size has type unsigned short. That means that it can be at
most 32768. However, there are architectures that can run with 64k pages
(for example arm64) and on these architectures, it may be possible to
create block devices with 64k block size.

For exmaple (run this on an architecture with 64k pages):

Mount will fail with this error because it tries to read the superblock using 2-sector
access:
  device-mapper: writecache: I/O is not aligned, sector 2, size 1024, block size 65536
  EXT4-fs (dm-0): unable to read superblock

This patch changes the logical block size from unsigned short to unsigned
int to avoid the overflow.

Cc: stable@vger.kernel.org
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix built-in early-load Intel microcode alignment

commit f5ae2ea6347a308cfe91f53b53682ce635497d0d upstream.

Intel Software Developer's Manual, volume 3, chapter 9.11.6 says:

 "Note that the microcode update must be aligned on a 16-byte boundary
  and the size of the microcode update must be 1-KByte granular"

When early-load Intel microcode is loaded from initramfs, userspace tool
'iucode_tool' has already 16-byte aligned those microcode bits in that
initramfs image.  Image that was created something like this:

 iucode_tool --write-earlyfw=FOO.cpio microcode-files...

However, when early-load Intel microcode is loaded from built-in
firmware BLOB using CONFIG_EXTRA_FIRMWARE= kernel config option, that
16-byte alignment is not guaranteed.

Fix this by forcing all built-in firmware BLOBs to 16-byte alignment.

[ If we end up having other firmware with much bigger alignment
  requirements, we might need to introduce some method for the firmware
  to specify it, this is the minimal "just increase the alignment a bit
  to account for this one special case" patch    - Linus ]

Signed-off-by: Jari Ruusu <jari.ruusu@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: seq: Fix racy access for queue timer in proc read

commit 60adcfde92fa40fcb2dbf7cc52f9b096e0cd109a upstream.

snd_seq_info_timer_read() reads the information of the timer assigned
for each queue, but it's done in a racy way which may lead to UAF as
spotted by syzkaller.

This patch applies the missing q->timer_mutex lock while accessing the
timer object as well as a slight code change to adapt the standard
coding style.

Reported-by: syzbot+2b2ef983f973e5c40943@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200115203733.26530-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ocfs2: call journal flush to mark journal as empty after journal recovery when mount

[ Upstream commit 397eac17f86f404f5ba31d8c3e39ec3124b39fd3 ]

If journal is dirty when mount, it will be replayed but jbd2 sb log tail
cannot be updated to mark a new start because journal->j_flag has
already been set with JBD2_ABORT first in journal_init_common.

When a new transaction is committed, it will be recored in block 1
first(journal->j_tail is set to 1 in journal_reset).  If emergency
restart happens again before journal super block is updated
unfortunately, the new recorded trans will not be replayed in the next
mount.

The following steps describe this procedure in detail.
1. mount and touch some files
2. these transactions are committed to journal area but not checkpointed
3. emergency restart
4. mount again and its journals are replayed
5. journal super block's first s_start is 1, but its s_seq is not updated
6. touch a new file and its trans is committed but not checkpointed
7. emergency restart again
8. mount and journal is dirty, but trans committed in 6 will not be
replayed.

This exception happens easily when this lun is used by only one node.
If it is used by multi-nodes, other node will replay its journal and its
journal super block will be updated after recovery like what this patch
does.

ocfs2_recover_node->ocfs2_replay_journal.

The following jbd2 journal can be generated by touching a new file after
journal is replayed, and seq 15 is the first valid commit, but first seq
is 13 in journal super block.

logdump:
  Block 0: Journal Superblock
  Seq: 0   Type: 4 (JBD2_SUPERBLOCK_V2)
  Blocksize: 4096   Total Blocks: 32768   First Block: 1
  First Commit ID: 13   Start Log Blknum: 1
  Error: 0
  Feature Compat: 0
  Feature Incompat: 2 block64
  Feature RO compat: 0
  Journal UUID: 4ED3822C54294467A4F8E87D2BA4BC36
  FS Share Cnt: 1   Dynamic Superblk Blknum: 0
  Per Txn Block Limit    Journal: 0    Data: 0

  Block 1: Journal Commit Block
  Seq: 14   Type: 2 (JBD2_COMMIT_BLOCK)

  Block 2: Journal Descriptor
  Seq: 15   Type: 1 (JBD2_DESCRIPTOR_BLOCK)
  No. Blocknum        Flags
   0. 587             none
  UUID: 00000000000000000000000000000000
   1. 8257792         JBD2_FLAG_SAME_UUID
   2. 619             JBD2_FLAG_SAME_UUID
   3. 24772864        JBD2_FLAG_SAME_UUID
   4. 8257802         JBD2_FLAG_SAME_UUID
   5. 513             JBD2_FLAG_SAME_UUID JBD2_FLAG_LAST_TAG
  ...
  Block 7: Inode
  Inode: 8257802   Mode: 0640   Generation: 57157641 (0x3682809)
  FS Generation: 2839773110 (0xa9437fb6)
  CRC32: 00000000   ECC: 0000
  Type: Regular   Attr: 0x0   Flags: Valid
  Dynamic Features: (0x1) InlineData
  User: 0 (root)   Group: 0 (root)   Size: 7
  Links: 1   Clusters: 0
  ctime: 0x5de5d870 0x11104c61 -- Tue Dec  3 11:37:20.286280801 2019
  atime: 0x5de5d870 0x113181a1 -- Tue Dec  3 11:37:20.288457121 2019
  mtime: 0x5de5d870 0x11104c61 -- Tue Dec  3 11:37:20.286280801 2019
  dtime: 0x0 -- Thu Jan  1 08:00:00 1970
  ...
  Block 9: Journal Commit Block
  Seq: 15   Type: 2 (JBD2_COMMIT_BLOCK)

The following is journal recovery log when recovering the upper jbd2
journal when mount again.

syslog:
  ocfs2: File system on device (252,1) was not unmounted cleanly, recovering it.
  fs/jbd2/recovery.c:(do_one_pass, 449): Starting recovery pass 0
  fs/jbd2/recovery.c:(do_one_pass, 449): Starting recovery pass 1
  fs/jbd2/recovery.c:(do_one_pass, 449): Starting recovery pass 2
  fs/jbd2/recovery.c:(jbd2_journal_recover, 278): JBD2: recovery, exit status 0, recovered transactions 13 to 13

Due to first commit seq 13 recorded in journal super is not consistent
with the value recorded in block 1(seq is 14), journal recovery will be
terminated before seq 15 even though it is an unbroken commit, inode
8257802 is a new file and it will be lost.

Link: http://lkml.kernel.org/r/20191217020140.2197-1-li.kai4@h3c.com
Signed-off-by: Kai Li <li.kai4@h3c.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: Changwei Ge <gechangwei@live.cn>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hexagon: work around compiler crash

[ Upstream commit 63e80314ab7cf4783526d2e44ee57a90514911c9 ]

Clang cannot translate the string "r30" into a valid register yet.

Link: https://github.com/ClangBuiltLinux/linux/issues/755
Link: http://lkml.kernel.org/r/20191028155722.23419-1-ndesaulniers@google.com
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Suggested-by: Sid Manning <sidneym@quicinc.com>
Reviewed-by: Brian Cain <bcain@codeaurora.org>
Cc: Allison Randal <allison@lohutok.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Richard Fontana <rfontana@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rseq/selftests: Turn off timeout setting

[ Upstream commit af9cb29c5488381083b0b5ccdfb3cd931063384a ]

As the rseq selftests can run for a long period of time, disable the
timeout that the general selftests have.

Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Paul E. McKenney" <paulmck@linux.ibm.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Paul Turner <pjt@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: msm6242: Fix reading of 10-hour digit

commit e34494c8df0cd96fc432efae121db3212c46ae48 upstream.

The driver was reading the wrong register as the 10-hour digit due to
a misplaced ')'. It was in fact reading the 1-second digit register due
to this bug.

Also remove the use of a magic number for the hour mask and use the define
for it which was already present.

Fixes: 4f9b9bba1dd1 ("rtc: Add an RTC driver for the Oki MSM6242")
Tested-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Link: https://lore.kernel.org/r/20191116110548.8562-1-jongk@linux-m68k.org
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: Remove unnecessary NULL check in rtl_regd_init

commit 091c6e9c083f7ebaff00b37ad13562d51464d175 upstream.

When building with Clang + -Wtautological-pointer-compare:

drivers/net/wireless/realtek/rtlwifi/regd.c:389:33: warning: comparison
of address of 'rtlpriv->regd' equal to a null pointer is always false
[-Wtautological-pointer-compare]
        if (wiphy == NULL || &rtlpriv->regd == NULL)
                              ~~~~~~~~~^~~~    ~~~~
1 warning generated.

The address of an array member is never NULL unless it is the first
struct member so remove the unnecessary check. This was addressed in
the staging version of the driver in commit f986978b32b3 ("Staging:
rtlwifi: remove unnecessary NULL check").

While we are here, fix the following checkpatch warning:

CHECK: Comparison to NULL could be written "!wiphy"
35: FILE: drivers/net/wireless/realtek/rtlwifi/regd.c:389:
+       if (wiphy == NULL)

Fixes: 0c8173385e54 ("rtl8192ce: Add new driver")
Link:https://github.com/ClangBuiltLinux/linux/issues/750
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: atmel: fix handling of cs_change set on non-last xfer

commit fed8d8c7a6dc2a76d7764842853d81c770b0788e upstream.

The driver does the wrong thing when cs_change is set on a non-last
xfer in a message.  When cs_change is set, the driver deactivates the
CS and leaves it off until a later xfer again has cs_change set whereas
it should be briefly toggling CS off and on again.

This patch brings the behaviour of the driver back in line with the
documentation and common sense.  The delay of 10 us is the same as is
used by the default spi_transfer_one_message() function in spi.c.
[gregory: rebased on for-5.5 from spi tree]
Fixes: 8090d6d1a415 ("spi: atmel: Refactor spi-atmel to use SPI framework queue")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191018153504.4249-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: exynos4-is: Fix recursive locking in isp_video_release()

commit 704c6c80fb471d1bb0ef0d61a94617d1d55743cd upstream.

>From isp_video_release(), &isp->video_lock is held and subsequent
vb2_fop_release() tries to lock vdev->lock which is same with the
previous one. Replace vb2_fop_release() with _vb2_fop_release() to
fix the recursive locking.

Fixes: 1380f5754cb0 ("[media] videobuf2: Add missing lock held on vb2_fop_release")
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: pch_uart: correct usage of dma_unmap_sg

commit 74887542fdcc92ad06a48c0cca17cdf09fc8aa00 upstream.

Per Documentation/DMA-API-HOWTO.txt,
To unmap a scatterlist, just call:
dma_unmap_sg(dev, sglist, nents, direction);

.. note::

The 'nents' argument to the dma_unmap_sg call must be
the _same_ one you passed into the dma_map_sg call,
it should _NOT_ be the 'count' value _returned_ from the
dma_map_sg call.

However in the driver, priv->nent is directly assigned with value
returned from dma_map_sg, and dma_unmap_sg use priv->nent for unmap,
this breaks the API usage.

So introduce a new entry orig_nent to remember 'nents'.

Fixes: da3564ee027e ("pch_uart: add multi-scatter processing")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1573623259-6339-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: imx: use the sg count from dma_map_sg

commit 596fd8dffb745afcebc0ec6968e17fe29f02044c upstream.

The dmaengine_prep_slave_sg needs to use sg count returned
by dma_map_sg, not use sport->dma_tx_nents, because the return
value of dma_map_sg is not always same with "nents".

Fixes: b4cdc8f61beb ("serial: imx: add DMA support for imx6q")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1573108875-26530-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

compat_ioctl: handle SIOCOUTQNSD

commit 9d7bf41fafa5b5ddd4c13eb39446b0045f0a8167 upstream.

Unlike the normal SIOCOUTQ, SIOCOUTQNSD was never handled in compat
mode. Add it to the common socket compat handler along with similar
ones.

Fixes: 2f4e1b397097 ("tcp: ioctl type SIOCOUTQNSD returns amount of data not sent")
Cc: Eric Dumazet <edumazet@google.com>
Cc: netdev@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: samsung: exynos5420: Preserve CPU clocks configuration during suspend/resume

commit e21be0d1d7bd7f78a77613f6bcb6965e72b22fc1 upstream.

Save and restore top PLL related configuration registers for big (APLL)
and LITTLE (KPLL) cores during suspend/resume cycle. So far, CPU clocks
were reset to default values after suspend/resume cycle and performance
after system resume was affected when performance governor has been selected.

Fixes: 773424326b51 ("clk: samsung: exynos5420: add more registers to restore list")
Signed-off-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mei: fix modalias documentation

commit 73668309215285366c433489de70d31362987be9 upstream.

mei client bus added the client protocol version to the device alias,
but ABI documentation was not updated.

Fixes: b26864cad1c9 (mei: bus: add client protocol version to the device alias)
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191008005735.12707-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: imu: adis16480: assign bias value only if operation succeeded

commit 9b742763d9d4195e823ae6ece760c9ed0500c1dc upstream.

This was found only after the whole thing with the inline functions, but
the compiler actually found something. The value of the `bias` (in
adis16480_get_calibbias()) should only be set if the read operation was
successful.

No actual known problem occurs as users of this function all
ultimately check the return value.  Hence probably not stable material.

Fixes: 2f3abe6cbb6c9 ("iio:imu: Add support for the ADIS16480 and similar IMUs")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform/x86: asus-wmi: Fix keyboard brightness cannot be set to 0

commit 176a7fca81c5090a7240664e3002c106d296bf31 upstream.

Some of ASUS laptops like UX431FL keyboard backlight cannot be set to
brightness 0. According to ASUS' information, the brightness should be
0x80 ~ 0x83. This patch fixes it by following the logic.

Fixes: e9809c0b9670 ("asus-wmi: add keyboard backlight support")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: sd: Clear sdkp->protection_type if disk is reformatted without PI

commit 465f4edaecc6c37f81349233e84d46246bcac11a upstream.

If an attached disk with protection information enabled is reformatted
to Type 0 the revalidation code does not clear the original protection
type and subsequent accesses will keep setting RDPROTECT/WRPROTECT.

Set the protection type to 0 if the disk reports PROT_EN=0 in READ
CAPACITY(16).

[mkp: commit desc]

Fixes: fe542396da73 ("[SCSI] sd: Ensure we correctly disable devices with unknown protection type")
Link: https://lore.kernel.org/r/1578532344-101668-1-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: enclosure: Fix stale device oops with hot replug

commit 529244bd1afc102ab164429d338d310d5d65e60d upstream.

Doing an add/remove/add on a SCSI device in an enclosure leads to an oops
caused by poisoned values in the enclosure device list pointers.  The
reason is because we are keeping the enclosure device across the enclosed
device add/remove/add but the current code is doing a
device_add/device_del/device_add on it.  This is the wrong thing to do in
sysfs, so fix it by not doing a device_del on the enclosure device simply
because of a hot remove of the drive in the slot.

[mkp: added missing email addresses]

Fixes: 43d8eb9cfd0a ("[SCSI] ses: add support for enclosure component hot removal")
Link: https://lore.kernel.org/r/1578532892.3852.10.camel@HansenPartnership.com
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reported-by: Luo Jiaxing <luojiaxing@huawei.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/srpt: Report the SCSI residual to the initiator

commit e88982ad1bb12db699de96fbc07096359ef6176c upstream.

The code added by this patch is similar to the code that already exists in
ibmvscsis_determine_resid(). This patch has been tested by running the
following command:

strace sg_raw -r 1k /dev/sdb 12 00 00 00 60 00 -o inquiry.bin |&
    grep resid=

Link: https://lore.kernel.org/r/20191105214632.183302-1-bvanassche@acm.org
Fixes: a42d985bd5b2 ("ib_srpt: Initial SRP Target merge for v3.3-rc1")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Honggang Li <honli@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: Adjust indentation in smb2_open_file

commit 7935799e041ae10d380d04ea23868240f082bd11 upstream.

Clang warns:

../fs/cifs/smb2file.c:70:3: warning: misleading indentation; statement
is not part of the previous 'if' [-Wmisleading-indentation]
         if (oparms->tcon->use_resilient) {
         ^
../fs/cifs/smb2file.c:66:2: note: previous statement is here
        if (rc)
        ^
1 warning generated.

This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.

Fixes: 592fafe644bf ("Add resilienthandles mount parm")
Link: https://github.com/ClangBuiltLinux/linux/issues/826
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hsr: reset network header when supervision frame is created

commit 3ed0a1d563903bdb4b4c36c58c4d9c1bcb23a6e6 upstream.

The supervision frame is L2 frame.
When supervision frame is created, hsr module doesn't set network header.
If tap routine is enabled, dev_queue_xmit_nit() is called and it checks
network_header. If network_header pointer wasn't set(or invalid),
it resets network_header and warns.
In order to avoid unnecessary warning message, resetting network_header
is needed.

Test commands:
    ip netns add nst
    ip link add veth0 type veth peer name veth1
    ip link add veth2 type veth peer name veth3
    ip link set veth1 netns nst
    ip link set veth3 netns nst
    ip link set veth0 up
    ip link set veth2 up
    ip link add hsr0 type hsr slave1 veth0 slave2 veth2
    ip a a 192.168.100.1/24 dev hsr0
    ip link set hsr0 up
    ip netns exec nst ip link set veth1 up
    ip netns exec nst ip link set veth3 up
    ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
    ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
    ip netns exec nst ip link set hsr1 up
    tcpdump -nei veth0

Splat looks like:
[  175.852292][    C3] protocol 88fb is buggy, dev veth0

Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gpio: Fix error message on out-of-range GPIO in lookup table

commit d935bd50dd14a7714cbdba9a76435dbb56edb1ae upstream.

When a GPIO offset in a lookup table is out-of-range, the printed error
message (1) does not include the actual out-of-range value, and (2)
contains an off-by-one error in the upper bound.

Avoid user confusion by also printing the actual GPIO offset, and
correcting the upper bound of the range.
While at it, use "%u" for unsigned int.

Sample impact:

    -requested GPIO 0 is out of range [0..32] for chip e6052000.gpio
    +requested GPIO 0 (45) is out of range [0..31] for chip e6052000.gpio

Fixes: 2a3cf6a3599e9015 ("gpiolib: return -ENOENT if no GPIO mapping exists")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191127095919.4214-1-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu: Remove device link to group on failure

commit 7d4e6ccd1fb09dbfbc49746ca82bd5c25ad4bfe4 upstream.

This adds the missing teardown step that removes the device link from
the group when the device addition fails.

Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Fixes: 797a8b4d768c5 ("iommu: Handle default domain attach failure")
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: mt6397: fix alarm register overwrite

commit 653997eeecef95c3ead4fba1b2d27e6a5854d6cd upstream.

Alarm registers high byte was reserved for other functions.
This add mask in alarm registers operation functions.
This also fix error condition in interrupt handler.

Fixes: fc2979118f3f ("rtc: mediatek: Add MT6397 RTC driver")

Signed-off-by: Ran Bi <ran.bi@mediatek.com>
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Link: https://lore.kernel.org/r/1576057435-3561-6-git-send-email-hsin-hsiung.wang@mediatek.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dccp: Fix memleak in __feat_register_sp

commit 1d3ff0950e2b40dc861b1739029649d03f591820 upstream.

If dccp_feat_push_change fails, we forget free the mem
which is alloced by kmemdup in dccp_feat_clone_sp_val.

Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e8ef967a54f4 ("dccp: Registration routines for changing feature values")
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: add more paranoia checking in ext4_expand_extra_isize handling

commit 4ea99936a1630f51fc3a2d61a58ec4a1c4b7d55a upstream.

It's possible to specify a non-zero s_want_extra_isize via debugging
option, and this can cause bad things(tm) to happen when using a file
system with an inode size of 128 bytes.

Add better checking when the file system is mounted, as well as when
we are actually doing the trying to do the inode expansion.

Link: https://lore.kernel.org/r/20191110121510.GH23325@mit.edu
Reported-by: syzbot+f8d6f8386ceacdbfff57@syzkaller.appspotmail.com
Reported-by: syzbot+33d7ea72e47de3bdf4e1@syzkaller.appspotmail.com
Reported-by: syzbot+44b6763edfc17144296f@syzkaller.appspotmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[bwh: Backported to 4.4: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix use-after-free race with debug_want_extra_isize

commit 7bc04c5c2cc467c5b40f2b03ba08da174a0d5fa7 upstream.

When remounting with debug_want_extra_isize, we were not performing the
same checks that we do during a normal mount.  That allowed us to set a
value for s_want_extra_isize that reached outside the s_inode_size.

Fixes: e2b911c53584 ("ext4: clean up feature test macros with predicate functions")
Reported-by: syzbot+f584efa0ac7213c226b7@syzkaller.appspotmail.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Barret Rhoden <brho@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[bwh: Backported to 4.4: The debug_want_extra_isize mount option is not
 supported]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wimax: i2400: Fix memory leak in i2400m_op_rfkill_sw_toggle

commit 6f3ef5c25cc762687a7341c18cbea5af54461407 upstream.

In the implementation of i2400m_op_rfkill_sw_toggle() the allocated
buffer for cmd should be released before returning. The
documentation for i2400m_msg_to_dev() says when it returns the buffer
can be reused. Meaning cmd should be released in either case. Move
kfree(cmd) before return to be reached by all execution paths.

Fixes: 2507e6ab7a9a ("wimax: i2400: fix memory leak")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wimax: i2400: fix memory leak

commit 2507e6ab7a9a440773be476141a255934468c5ef upstream.

In i2400m_op_rfkill_sw_toggle cmd buffer should be released along with
skb response.

Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen: let alloc_xenballooned_pages() fail if not enough memory free

commit a1078e821b605813b63bf6bca414a85f804d5c66 upstream.

Instead of trying to allocate pages with GFP_USER in
add_ballooned_pages() check the available free memory via
si_mem_available(). GFP_USER is far less limiting memory exhaustion
than the test via si_mem_available().

This will avoid dom0 running out of memory due to excessive foreign
page mappings especially on ARM and on x86 in PVH mode, as those don't
have a pre-ballooned area which can be used for foreign mappings.

As the normal ballooning suffers from the same problem don't balloon
down more than si_mem_available() pages in one iteration. At the same
time limit the default maximum number of retries.

This is part of XSA-300.

Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/page_alloc.c: calculate 'available' memory in a separate function

commit d02bd27bd33dd7e8d22594cd568b81be0cb584cd upstream.

Add a new field, VIRTIO_BALLOON_S_AVAIL, to virtio_balloon memory
statistics protocol, corresponding to 'Available' in /proc/meminfo.

It indicates to the hypervisor how big the balloon can be inflated
without pushing the guest system to swap.  This metric would be very
useful in VM orchestration software to improve memory management of
different VMs under overcommit.

This patch (of 2):

Factor out calculation of the available memory counter into a separate
exportable function, in order to be able to use it in other parts of the
kernel.

In particular, it appears a relevant metric to report to the hypervisor
via virtio-balloon statistics interface (in a followup patch).

Signed-off-by: Igor Redko <redkoi@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 4.4 as dependency of commit a1078e821b60
 "xen: let alloc_xenballooned_pages() fail if not enough memory free"]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: line6: Fix memory leak at line6_init_pcm() error path

commit 1bc8d18c75fef3b478dbdfef722aae09e2a9fde7 upstream.

I forgot to release the allocated object at the early error path in
line6_init_pcm().  For addressing it, slightly shuffle the code so
that the PCM destructor (pcm->private_free) is assigned properly
before all error paths.

Fixes: 3450121997ce ("ALSA: line6: Fix write on zero-sized buffer")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 4.4: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: line6: Fix write on zero-sized buffer

commit 3450121997ce872eb7f1248417225827ea249710 upstream.

LINE6 drivers allocate the buffers based on the value returned from
usb_maxpacket() calls.  The manipulated device may return zero for
this, and this results in the kmalloc() with zero size (and it may
succeed) while the other part of the driver code writes the packet
data with the fixed size -- which eventually overwrites.

This patch adds a simple sanity check for the invalid buffer size for
avoiding that problem.

Reported-by: syzbot+219f00fb49874dcaea17@syzkaller.appspotmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 4.4: Driver doesn't support asymmetrical packet
 sizes, so only check snd_line6_pcm::max_packet_size]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

p54usb: Fix race between disconnect and firmware loading

commit 6e41e2257f1094acc37618bf6c856115374c6922 upstream.

The syzbot fuzzer found a bug in the p54 USB wireless driver.  The
issue involves a race between disconnect and the firmware-loader
callback routine, and it has several aspects.

One big problem is that when the firmware can't be loaded, the
callback routine tries to unbind the driver from the USB _device_ (by
calling device_release_driver) instead of from the USB _interface_ to
which it is actually bound (by calling usb_driver_release_interface).

The race involves access to the private data structure.  The driver's
disconnect handler waits for a completion that is signalled by the
firmware-loader callback routine.  As soon as the completion is
signalled, you have to assume that the private data structure may have
been deallocated by the disconnect handler -- even if the firmware was
loaded without errors.  However, the callback routine does access the
private data several times after that point.

Another problem is that, in order to ensure that the USB device
structure hasn't been freed when the callback routine runs, the driver
takes a reference to it.  This isn't good enough any more, because now
that the callback routine calls usb_driver_release_interface, it has
to ensure that the interface structure hasn't been freed.

Finally, the driver takes an unnecessary reference to the USB device
structure in the probe function and drops the reference in the
disconnect handler.  This extra reference doesn't accomplish anything,
because the USB core already guarantees that a device structure won't
be deallocated while a driver is still bound to any of its interfaces.

To fix these problems, this patch makes the following changes:

Call usb_driver_release_interface() rather than
device_release_driver().

Don't signal the completion until after the important
information has been copied out of the private data structure,
and don't refer to the private data at all thereafter.

Lock udev (the interface's parent) before unbinding the driver
instead of locking udev->parent.

During the firmware loading process, take a reference to the
USB interface instead of the USB device.

Don't take an unnecessary reference to the device during probe
(and then don't drop it during disconnect).

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+200d4bb11b23d929335f@syzkaller.appspotmail.com
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 4.4: adjust filename]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: usb:zr364xx:Fix KASAN:null-ptr-deref Read in zr364xx_vidioc_querycap

commit 5d2e73a5f80a5b5aff3caf1ec6d39b5b3f54b26e upstream.

SyzKaller hit the null pointer deref while reading from uninitialized
udev->product in zr364xx_vidioc_querycap().

==================================================================
BUG: KASAN: null-ptr-deref in read_word_at_a_time+0xe/0x20
include/linux/compiler.h:274
Read of size 1 at addr 0000000000000000 by task v4l_id/5287

CPU: 1 PID: 5287 Comm: v4l_id Not tainted 5.1.0-rc3-319004-g43151d6 #6
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
  __dump_stack lib/dump_stack.c:77 [inline]
  dump_stack+0xe8/0x16e lib/dump_stack.c:113
  kasan_report.cold+0x5/0x3c mm/kasan/report.c:321
  read_word_at_a_time+0xe/0x20 include/linux/compiler.h:274
  strscpy+0x8a/0x280 lib/string.c:207
  zr364xx_vidioc_querycap+0xb5/0x210 drivers/media/usb/zr364xx/zr364xx.c:706
  v4l_querycap+0x12b/0x340 drivers/media/v4l2-core/v4l2-ioctl.c:1062
  __video_do_ioctl+0x5bb/0xb40 drivers/media/v4l2-core/v4l2-ioctl.c:2874
  video_usercopy+0x44e/0xf00 drivers/media/v4l2-core/v4l2-ioctl.c:3056
  v4l2_ioctl+0x14e/0x1a0 drivers/media/v4l2-core/v4l2-dev.c:364
  vfs_ioctl fs/ioctl.c:46 [inline]
  file_ioctl fs/ioctl.c:509 [inline]
  do_vfs_ioctl+0xced/0x12f0 fs/ioctl.c:696
  ksys_ioctl+0xa0/0xc0 fs/ioctl.c:713
  __do_sys_ioctl fs/ioctl.c:720 [inline]
  __se_sys_ioctl fs/ioctl.c:718 [inline]
  __x64_sys_ioctl+0x74/0xb0 fs/ioctl.c:718
  do_syscall_64+0xcf/0x4f0 arch/x86/entry/common.c:290
  entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7f3b56d8b347
Code: 90 90 90 48 8b 05 f1 fa 2a 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff
ff c3 90 90 90 90 90 90 90 90 90 90 b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff
ff 73 01 c3 48 8b 0d c1 fa 2a 00 31 d2 48 29 c2 64
RSP: 002b:00007ffe005d5d68 EFLAGS: 00000202 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f3b56d8b347
RDX: 00007ffe005d5d70 RSI: 0000000080685600 RDI: 0000000000000003
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000400884
R13: 00007ffe005d5ec0 R14: 0000000000000000 R15: 0000000000000000
==================================================================

For this device udev->product is not initialized and accessing it causes a NULL pointer deref.

The fix is to check for NULL before strscpy() and copy empty string, if
product is NULL

Reported-by: syzbot+66010012fd4c531a1a96@syzkaller.appspotmail.com
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
[bwh: Backported to 4.4: This function uses strlcpy() instead of strscpy()]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: Do not send Layer 2 Update frame before authorization

commit 3e493173b7841259a08c5c8e5cbe90adb349da7e upstream.

The Layer 2 Update frame is used to update bridges when a station roams
to another AP even if that STA does not transmit any frames after the
reassociation. This behavior was described in IEEE Std 802.11F-2003 as
something that would happen based on MLME-ASSOCIATE.indication, i.e.,
before completing 4-way handshake. However, this IEEE trial-use
recommended practice document was published before RSN (IEEE Std
802.11i-2004) and as such, did not consider RSN use cases. Furthermore,
IEEE Std 802.11F-2003 was withdrawn in 2006 and as such, has not been
maintained amd should not be used anymore.

Sending out the Layer 2 Update frame immediately after association is
fine for open networks (and also when using SAE, FT protocol, or FILS
authentication when the station is actually authenticated by the time
association completes). However, it is not appropriate for cases where
RSN is used with PSK or EAP authentication since the station is actually
fully authenticated only once the 4-way handshake completes after
authentication and attackers might be able to use the unauthenticated
triggering of Layer 2 Update frame transmission to disrupt bridge
behavior.

Fix this by postponing transmission of the Layer 2 Update frame from
station entry addition to the point when the station entry is marked
authorized. Similarly, send out the VLAN binding update only if the STA
entry has already been authorized.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 4.4: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfg80211/mac80211: make ieee80211_send_layer2_update a public function

commit 30ca1aa536211f5ac3de0173513a7a99a98a97f3 upstream.

Make ieee80211_send_layer2_update() a common function so other drivers
can re-use it.

Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 4.4 as dependency of commit 3e493173b784
 "mac80211: Do not send Layer 2 Update frame before authorization":
 - Retain type-casting of skb_put() return value
 - Adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rsi: add fix for crash during assertions

commit abd39c6ded9db53aa44c2540092bdd5fb6590fa8 upstream.

Observed crash in some scenarios when assertion has occurred,
this is because hw structure is freed and is tried to get
accessed in some functions where null check is already
present. So, avoided the crash by making the hw to NULL after
freeing.

Signed-off-by: Sanjay Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: hidraw, uhid: Always report EPOLLOUT

[ Upstream commit 9e635c2851df6caee651e589fbf937b637973c91 ]

hidraw and uhid device nodes are always available for writing so we should
always report EPOLLOUT and EPOLLWRNORM bits, not only in the cases when
there is nothing to read.

Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: be54e7461ffdc ("HID: uhid: Fix returning EPOLLOUT from uhid_char_poll")
Fixes: 9f3b61dc1dd7b ("HID: hidraw: Fix returning EPOLLOUT from hidraw_poll")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: hidraw: Fix returning EPOLLOUT from hidraw_poll

[ Upstream commit 9f3b61dc1dd7b81e99e7ed23776bb64a35f39e1a ]

When polling a connected /dev/hidrawX device, it is useful to get the
EPOLLOUT when writing is possible. Since writing is possible as soon as
the device is connected, always return it.

Right now EPOLLOUT is only returned when there are also input reports
are available. This works if devices start sending reports when
connected, but some HID devices might need an output report first before
sending any input reports. This change will allow using EPOLLOUT here as
well.

Fixes: 378b80370aa1 ("hidraw: Return EPOLLOUT from hidraw_poll")
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hidraw: Return EPOLLOUT from hidraw_poll

[ Upstream commit 378b80370aa1fe50f9c48a3ac8af3e416e73b89f ]

Always return EPOLLOUT from hidraw_poll when a device is connected.
This is safe since writes are always possible (but will always block).

hidraw does not support non-blocking writes and instead always calls
blocking backend functions on write requests. Hence, so far, a call to
poll never returned EPOLLOUT, which confuses tools like socat.

Signed-off-by: Fabian Henneke <fabian.henneke@gmail.com>
In-reply-to: <CA+hv5qkyis03CgYTWeWX9cr0my-d2Oe+aZo+mjmWRXgjrGqyrw@mail.gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Linux 4.4.210

drm/i915/gen9: Clear residual context state on context switch

commit bc8a76a152c5f9ef3b48104154a65a68a8b76946 upstream.

Intel ID: PSIRT-TA-201910-001
CVEID: CVE-2019-14615

Intel GPU Hardware prior to Gen11 does not clear EU state
during a context switch. This can result in information
leakage between contexts.

For Gen8 and Gen9, hardware provides a mechanism for
fast cleardown of the EU state, by issuing a PIPE_CONTROL
with bit 27 set. We can use this in a context batch buffer
to explicitly cleardown the state on every context switch.

As this workaround is already in place for gen8, we can borrow
the code verbatim for Gen9.

Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Kumar Valsan Prathap <prathap.kumar.valsan@intel.com>
Cc: Chris Wilson <chris.p.wilson@intel.com>
Cc: Balestrieri Francesco <francesco.balestrieri@intel.com>
Cc: Bloomfield Jon <jon.bloomfield@intel.com>
Cc: Dutt Sudeep <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: ipset: avoid null deref when IPSET_ATTR_LINENO is present

commit 22dad713b8a5ff488e07b821195270672f486eb2 upstream.

The set uadt functions assume lineno is never NULL, but it is in
case of ip_set_utest().

syzkaller managed to generate a netlink message that calls this with
LINENO attr present:

general protection fault: 0000 [#1] PREEMPT SMP KASAN
RIP: 0010:hash_mac4_uadt+0x1bc/0x470 net/netfilter/ipset/ip_set_hash_mac.c:104
Call Trace:
 ip_set_utest+0x55b/0x890 net/netfilter/ipset/ip_set_core.c:1867
 nfnetlink_rcv_msg+0xcf2/0xfb0 net/netfilter/nfnetlink.c:229
 netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477
 nfnetlink_rcv+0x1ba/0x460 net/netfilter/nfnetlink.c:563

pass a dummy lineno storage, its easier than patching all set
implementations.

This seems to be a day-0 bug.

Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Reported-by: syzbot+34bd2369d38707f3f4a7@syzkaller.appspotmail.com
Fixes: a7b4f989a6294 ("netfilter: ipset: IP set core support")
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: arp_tables: init netns pointer in xt_tgchk_param struct

commit 1b789577f655060d98d20ed0c6f9fbd469d6ba63 upstream.

We get crash when the targets checkentry function tries to make
use of the network namespace pointer for arptables.

When the net pointer got added back in 2010, only ip/ip6/ebtables were
changed to initialize it, so arptables has this set to NULL.

This isn't a problem for normal arptables because no existing
arptables target has a checkentry function that makes use of par->net.

However, direct users of the setsockopt interface can provide any
target they want as long as its registered for ARP or UNPSEC protocols.

syzkaller managed to send a semi-valid arptables rule for RATEEST target
which is enough to trigger NULL deref:

kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
RIP: xt_rateest_tg_checkentry+0x11d/0xb40 net/netfilter/xt_RATEEST.c:109
[..]
 xt_check_target+0x283/0x690 net/netfilter/x_tables.c:1019
 check_target net/ipv4/netfilter/arp_tables.c:399 [inline]
 find_check_entry net/ipv4/netfilter/arp_tables.c:422 [inline]
 translate_table+0x1005/0x1d70 net/ipv4/netfilter/arp_tables.c:572
 do_replace net/ipv4/netfilter/arp_tables.c:977 [inline]
 do_arpt_set_ctl+0x310/0x640 net/ipv4/netfilter/arp_tables.c:1456

Fixes: add67461240c1d ("netfilter: add struct net * to target parameters")
Reported-by: syzbot+d7358a458d8a81aee898@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: Fix: Don't skip endpoint descriptors with maxpacket=0

commit 2548288b4fb059b2da9ceada172ef763077e8a59 upstream.

It turns out that even though endpoints with a maxpacket length of 0
aren't useful for data transfer, the descriptors do serve other
purposes.  In particular, skipping them will also skip over other
class-specific descriptors for classes such as UVC.  This unexpected
side effect has caused some UVC cameras to stop working.

In addition, the USB spec requires that when isochronous endpoint
descriptors are present in an interface's altsetting 0 (which is true
on some devices), the maxpacket size _must_ be set to 0.  Warning
about such things seems like a bad idea.

This patch updates an earlier commit which would log a warning and
skip these endpoint descriptors.  Now we only log a warning, and we
don't even do that for isochronous endpoints in altsetting 0.

We don't need to worry about preventing endpoints with maxpacket = 0
from ever being used for data transfers; usb_submit_urb() already
checks for this.

Reported-and-tested-by: Roger Whittaker <Roger.Whittaker@suse.com>
Fixes: d482c7bb0541 ("USB: Skip endpoints with 0 maxpacket length")
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://marc.info/?l=linux-usb&m=157790377329882&w=2
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001061040270.1514-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtl8xxxu: prevent leaking urb

commit a2cdd07488e666aa93a49a3fc9c9b1299e27ef3c upstream.

In rtl8xxxu_submit_int_urb if usb_submit_urb fails the allocated urb
should be released.

Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: bfa: release allocated memory in case of error

commit 0e62395da2bd5166d7c9e14cbc7503b256a34cb0 upstream.

In bfad_im_get_stats if bfa_port_get_stats fails, allocated memory needs to
be released.

Link: https://lore.kernel.org/r/20190910234417.22151-1-navid.emamdoost@gmail.com
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mwifiex: pcie: Fix memory leak in mwifiex_pcie_alloc_cmdrsp_buf

commit db8fd2cde93227e566a412cf53173ffa227998bc upstream.

In mwifiex_pcie_alloc_cmdrsp_buf, a new skb is allocated which should be
released if mwifiex_map_pci_memory() fails. The release is added.

Fixes: fc3314609047 ("mwifiex: use pci_alloc/free_consistent APIs for PCIe")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mwifiex: fix possible heap overflow in mwifiex_process_country_ie()

commit 3d94a4a8373bf5f45cf5f939e88b8354dbf2311b upstream.

mwifiex_process_country_ie() function parse elements of bss
descriptor in beacon packet. When processing WLAN_EID_COUNTRY
element, there is no upper limit check for country_ie_len before
calling memcpy. The destination buffer domain_info->triplet is an
array of length MWIFIEX_MAX_TRIPLET_802_11D(83). The remote
attacker can build a fake AP with the same ssid as real AP, and
send malicous beacon packet with long WLAN_EID_COUNTRY elemen
(country_ie_len > 83). Attacker can  force STA connect to fake AP
on a different channel. When the victim STA connects to fake AP,
will trigger the heap buffer overflow. Fix this by checking for
length and if found invalid, don not connect to the AP.

This fix addresses CVE-2019-14895.

Reported-by: huangwen <huangwenabc@gmail.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: always relink the port

commit 273f632912f1b24b642ba5b7eb5022e43a72f3b5 upstream.

If the serial device is disconnected and reconnected, it re-enumerates
properly but does not link it. fwiw, linking means just saving the port
index, so allow it always as there is no harm in saving the same value
again even if it tries to relink with the same port.

Fixes: fb2b90014d78 ("tty: link tty and port before configuring it as console")
Reported-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191227174434.12057-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: link tty and port before configuring it as console

commit fb2b90014d782d80d7ebf663e50f96d8c507a73c upstream.

There seems to be a race condition in tty drivers and I could see on
many boot cycles a NULL pointer dereference as tty_init_dev() tries to
do 'tty->port->itty = tty' even though tty->port is NULL.
'tty->port' will be set by the driver and if the driver has not yet done
it before we open the tty device we can get to this situation. By adding
some extra debug prints, I noticed that:

6.650130: uart_add_one_port
6.663849: register_console
6.664846: tty_open
6.674391: tty_init_dev
6.675456: tty_port_link_device

uart_add_one_port() registers the console, as soon as it registers, the
userspace tries to use it and that leads to tty_open() but
uart_add_one_port() has not yet done tty_port_link_device() and so
tty->port is not yet configured when control reaches tty_init_dev().

Further look into the code and tty_port_link_device() is done by
uart_add_one_port(). After registering the console uart_add_one_port()
will call tty_port_register_device_attr_serdev() and
tty_port_link_device() is called from this.

Call add tty_port_link_device() before uart_configure_port() is done and
add a check in tty_port_link_device() so that it only links the port if
it has not been done yet.

Suggested-by: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191212131602.29504-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: Add device code for TP-Link TL-WN727N v5.21

commit 58dcc5bf4030cab548d5c98cd4cd3632a5444d5a upstream.

This device was added to the stand-alone driver on github.
Add it to the staging driver as well.

Link: https://github.com/lwfinger/rtl8188eu/commit/b9b537aa25a8
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191228143725.24455-1-straube.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: dma: Correct parameter passed to IRQ handler

commit c80d0f4426c7fdc7efd6ae8d8b021dcfc89b4254 upstream.

The IRQ handler was passed a pointer to a struct dma_controller, but the
argument was then casted to a pointer to a struct musb_dma_controller.

Fixes: 427c4f333474 ("usb: struct device - replace bus_id with dev_name(), dev_set_name()")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20191216161844.772-2-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: Disable pullup at init

commit 96a0c12843109e5c4d5eb1e09d915fdd0ce31d25 upstream.

The pullup may be already enabled before the driver is initialized. This
happens for instance on JZ4740.

It has to be disabled at init time, as we cannot guarantee that a gadget
driver will be bound to the UDC.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Suggested-by: Bin Liu <b-liu@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200107152625.857-3-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add ZLP support for 0x1bc7/0x9010

commit 2438c3a19dec5e98905fd3ffcc2f24716aceda6b upstream.

Telit FN980 flashing device 0x1bc7/0x9010 requires zero packet
to be sent if out data size is is equal to the endpoint max size.

Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
[ johan: switch operands in conditional ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vt6656: set usb_set_intfdata on driver fail.

commit c0bcf9f3f5b661d4ace2a64a79ef661edd2a4dc8 upstream.

intfdata will contain stale pointer when the device is detached after
failed initialization when referenced in vt6656_disconnect

Provide driver access to it here and NULL it.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/6de448d7-d833-ef2e-dd7b-3ef9992fee0e@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: can_dropped_invalid_skb(): ensure an initialized headroom in outgoing CAN sk_buffs

commit e7153bf70c3496bac00e7e4f395bb8d8394ac0ea upstream.

KMSAN sysbot detected a read access to an untinitialized value in the
headroom of an outgoing CAN related sk_buff. When using CAN sockets this
area is filled appropriately - but when using a packet socket this
initialization is missing.

The problematic read access occurs in the CAN receive path which can
only be triggered when the sk_buff is sent through a (virtual) CAN
interface. So we check in the sending path whether we need to perform
the missing initializations.

Fixes: d3b58c47d330d ("can: replace timestamp as unique skb attribute")
Reported-by: syzbot+b02ff0707a97e4e79ebb@syzkaller.appspotmail.com
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.1
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: mscan: mscan_rx_poll(): fix rx path lockup when returning from polling to irq mode

commit 2d77bd61a2927be8f4e00d9478fe6996c47e8d45 upstream.

Under load, the RX side of the mscan driver can get stuck while TX still
works. Restarting the interface locks up the system. This behaviour
could be reproduced reliably on a MPC5121e based system.

The patch fixes the return value of the NAPI polling function (should be
the number of processed packets, not constant 1) and the condition under
which IRQs are enabled again after polling is finished.

With this patch, no more lockups were observed over a test period of ten
days.

Fixes: afa17a500a36 ("net/can: add driver for mscan family & mpc52xx_mscan")
Signed-off-by: Florian Faber <faber@faberman.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: gs_usb: gs_usb_probe(): use descriptors of current altsetting

commit 2f361cd9474ab2c4ab9ac8db20faf81e66c6279b upstream.

Make sure to always use the descriptors of the current alternate setting
to avoid future issues when accessing fields that may differ between
settings.

Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/dp_mst: correct the shifting in DP_REMOTE_I2C_READ

commit c4e4fccc5d52d881afaac11d3353265ef4eccb8b upstream.

[Why]
According to DP spec, it should shift left 4 digits for NO_STOP_BIT
in REMOTE_I2C_READ message. Not 5 digits.

In current code, NO_STOP_BIT is always set to zero which means I2C
master is always generating a I2C stop at the end of each I2C write
transaction while handling REMOTE_I2C_READ sideband message. This issue
might have the generated I2C signal not meeting the requirement. Take
random read in I2C for instance, I2C master should generate a repeat
start to start to read data after writing the read address. This issue
will cause the I2C master to generate a stop-start rather than a
re-start which is not expected in I2C random read.

[How]
Correct the shifting value of NO_STOP_BIT for DP_REMOTE_I2C_READ case in
drm_dp_encode_sideband_req().

Changes since v1:(https://patchwork.kernel.org/patch/11312667/)
* Add more descriptions in commit and cc to stable

Fixes: ad7f8a1f9ced ("drm/helper: add Displayport multi-stream helper (v0.6)")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200103055001.10287-1-Wayne.Lin@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: add safety guards to input_set_keycode()

commit cb222aed03d798fc074be55e59d9a112338ee784 upstream.

If we happen to have a garbage in input device's keycode table with values
too big we'll end up doing clear_bit() with offset way outside of our
bitmaps, damaging other objects within an input device or even outside of
it. Let's add sanity checks to the returned old keycodes.

Reported-by: syzbot+c769968809f9359b07aa@syzkaller.appspotmail.com
Reported-by: syzbot+76f3a30e88d256644c78@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20191207212757.GA245964@dtor-ws
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: hid-input: clear unmapped usages

commit 4f3882177240a1f55e45a3d241d3121341bead78 upstream.

We should not be leaving half-mapped usages with potentially invalid
keycodes, as that may confuse hidinput_find_key() when the key is located
by index, which may end up feeding way too large keycode into the VT
keyboard handler and cause OOB write there:

BUG: KASAN: global-out-of-bounds in clear_bit include/asm-generic/bitops-instrumented.h:56 [inline]
BUG: KASAN: global-out-of-bounds in kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
BUG: KASAN: global-out-of-bounds in kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
Write of size 8 at addr ffffffff89a1b2d8 by task syz-executor108/1722
...
 kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
 kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
 input_to_handler+0x3b6/0x4c0 drivers/input/input.c:118
 input_pass_values.part.0+0x2e3/0x720 drivers/input/input.c:145
 input_pass_values drivers/input/input.c:949 [inline]
 input_set_keycode+0x290/0x320 drivers/input/input.c:954
 evdev_handle_set_keycode_v2+0xc4/0x120 drivers/input/evdev.c:882
 evdev_do_ioctl drivers/input/evdev.c:1150 [inline]

Cc: stable@vger.kernel.org
Reported-by: syzbot+19340dff067c2d3835c0@syzkaller.appspotmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: uhid: Fix returning EPOLLOUT from uhid_char_poll

commit be54e7461ffdc5809b67d2aeefc1ddc9a91470c7 upstream.

Always return EPOLLOUT from uhid_char_poll to allow polling /dev/uhid
for writable state.

Fixes: 1f9dec1e0164 ("HID: uhid: allow poll()'ing on uhid devices")
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: Fix slab-out-of-bounds read in hid_field_extract

commit 8ec321e96e056de84022c032ffea253431a83c3c upstream.

The syzbot fuzzer found a slab-out-of-bounds bug in the HID report
handler.  The bug was caused by a report descriptor which included a
field with size 12 bits and count 4899, for a total size of 7349
bytes.

The usbhid driver uses at most a single-page 4-KB buffer for reports.
In the test there wasn't any problem about overflowing the buffer,
since only one byte was received from the device.  Rather, the bug
occurred when the HID core tried to extract the data from the report
fields, which caused it to try reading data beyond the end of the
allocated buffer.

This patch fixes the problem by rejecting any report whose total
length exceeds the HID_MAX_BUFFER_SIZE limit (minus one byte to allow
for a possible report index).  In theory a device could have a report
longer than that, but if there was such a thing we wouldn't handle it
correctly anyway.

Reported-and-tested-by: syzbot+09ef48aa58261464b621@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Have stack tracer compile when MCOUNT_INSN_SIZE is not defined

commit b8299d362d0837ae39e87e9019ebe6b736e0f035 upstream.

On some archs with some configurations, MCOUNT_INSN_SIZE is not defined, and
this makes the stack tracer fail to compile. Just define it to zero in this
case.

Link: https://lore.kernel.org/r/202001020219.zvE3vsty%lkp@intel.com
Cc: stable@vger.kernel.org
Fixes: 4df297129f622 ("tracing: Remove most or all of stack tracer stack size from stack_max_size")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kernel/trace: Fix do not unregister tracepoints when register sched_migrate_task fail

commit 50f9ad607ea891a9308e67b81f774c71736d1098 upstream.

In the function, if register_trace_sched_migrate_task() returns error,
sched_switch/sched_wakeup_new/sched_wakeup won't unregister. That is
why fail_deprobe_sched_switch was added.

Link: http://lkml.kernel.org/r/20191231133530.2794-1-pilgrimtao@gmail.com
Cc: stable@vger.kernel.org
Fixes: 478142c39c8c2 ("tracing: do not grab lock in wakeup latency function tracing")
Signed-off-by: Kaitao Cheng <pilgrimtao@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Apply the sample rate quirk for Bose Companion 5

commit 51d4efab7865e6ea6a4ebcd25b3f03c019515c4c upstream.

Bose Companion 5 (with USB ID 05a7:1020) doesn't seem supporting
reading back the sample rate, so the existing quirk is needed.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206063
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200104110936.14288-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: chipidea: host: Disable port power only if previously enabled

commit c1ffba305dbcf3fb9ca969c20a97acbddc38f8e9 upstream.

On shutdown, ehci_power_off() is called unconditionally to power off
each port, even if it was never called to power on the port.
For chipidea, this results in a call to ehci_ci_portpower() with a request
to power off ports even if the port was never powered on.
This results in the following warning from the regulator code.

WARNING: CPU: 0 PID: 182 at drivers/regulator/core.c:2596 _regulator_disable+0x1a8/0x210
unbalanced disables for usb_otg2_vbus
Modules linked in:
CPU: 0 PID: 182 Comm: init Not tainted 5.4.6 #1
Hardware name: Freescale i.MX7 Dual (Device Tree)
[<c0313658>] (unwind_backtrace) from [<c030d698>] (show_stack+0x10/0x14)
[<c030d698>] (show_stack) from [<c1133afc>] (dump_stack+0xe0/0x10c)
[<c1133afc>] (dump_stack) from [<c0349098>] (__warn+0xf4/0x10c)
[<c0349098>] (__warn) from [<c0349128>] (warn_slowpath_fmt+0x78/0xbc)
[<c0349128>] (warn_slowpath_fmt) from [<c09f36ac>] (_regulator_disable+0x1a8/0x210)
[<c09f36ac>] (_regulator_disable) from [<c09f374c>] (regulator_disable+0x38/0xe8)
[<c09f374c>] (regulator_disable) from [<c0df7bac>] (ehci_ci_portpower+0x38/0xdc)
[<c0df7bac>] (ehci_ci_portpower) from [<c0db4fa4>] (ehci_port_power+0x50/0xa4)
[<c0db4fa4>] (ehci_port_power) from [<c0db5420>] (ehci_silence_controller+0x5c/0xc4)
[<c0db5420>] (ehci_silence_controller) from [<c0db7644>] (ehci_stop+0x3c/0xcc)
[<c0db7644>] (ehci_stop) from [<c0d5bdc4>] (usb_remove_hcd+0xe0/0x19c)
[<c0d5bdc4>] (usb_remove_hcd) from [<c0df7638>] (host_stop+0x38/0xa8)
[<c0df7638>] (host_stop) from [<c0df2f34>] (ci_hdrc_remove+0x44/0xe4)
...

Keeping track of the power enable state avoids the warning and traceback.

Fixes: c8679a2fb8dec ("usb: chipidea: host: add portpower override")
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20191226155754.25451-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

chardev: Avoid potential use-after-free in 'chrdev_open()'

commit 68faa679b8be1a74e6663c21c3a9d25d32f1c079 upstream.

'chrdev_open()' calls 'cdev_get()' to obtain a reference to the
'struct cdev *' stashed in the 'i_cdev' field of the target inode
structure. If the pointer is NULL, then it is initialised lazily by
looking up the kobject in the 'cdev_map' and so the whole procedure is
protected by the 'cdev_lock' spinlock to serialise initialisation of
the shared pointer.

Unfortunately, it is possible for the initialising thread to fail *after*
installing the new pointer, for example if the subsequent '->open()' call
on the file fails. In this case, 'cdev_put()' is called, the reference
count on the kobject is dropped and, if nobody else has taken a reference,
the release function is called which finally clears 'inode->i_cdev' from
'cdev_purge()' before potentially freeing the object. The problem here
is that a racing thread can happily take the 'cdev_lock' and see the
non-NULL pointer in the inode, which can result in a refcount increment
from zero and a warning:

  |  ------------[ cut here ]------------
  |  refcount_t: addition on 0; use-after-free.
  |  WARNING: CPU: 2 PID: 6385 at lib/refcount.c:25 refcount_warn_saturate+0x6d/0xf0
  |  Modules linked in:
  |  CPU: 2 PID: 6385 Comm: repro Not tainted 5.5.0-rc2+ #22
  |  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
  |  RIP: 0010:refcount_warn_saturate+0x6d/0xf0
  |  Code: 05 55 9a 15 01 01 e8 9d aa c8 ff 0f 0b c3 80 3d 45 9a 15 01 00 75 ce 48 c7 c7 00 9c 62 b3 c6 08
  |  RSP: 0018:ffffb524c1b9bc70 EFLAGS: 00010282
  |  RAX: 0000000000000000 RBX: ffff9e9da1f71390 RCX: 0000000000000000
  |  RDX: ffff9e9dbbd27618 RSI: ffff9e9dbbd18798 RDI: ffff9e9dbbd18798
  |  RBP: 0000000000000000 R08: 000000000000095f R09: 0000000000000039
  |  R10: 0000000000000000 R11: ffffb524c1b9bb20 R12: ffff9e9da1e8c700
  |  R13: ffffffffb25ee8b0 R14: 0000000000000000 R15: ffff9e9da1e8c700
  |  FS:  00007f3b87d26700(0000) GS:ffff9e9dbbd00000(0000) knlGS:0000000000000000
  |  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  |  CR2: 00007fc16909c000 CR3: 000000012df9c000 CR4: 00000000000006e0
  |  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  |  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  |  Call Trace:
  |   kobject_get+0x5c/0x60
  |   cdev_get+0x2b/0x60
  |   chrdev_open+0x55/0x220
  |   ? cdev_put.part.3+0x20/0x20
  |   do_dentry_open+0x13a/0x390
  |   path_openat+0x2c8/0x1470
  |   do_filp_open+0x93/0x100
  |   ? selinux_file_ioctl+0x17f/0x220
  |   do_sys_open+0x186/0x220
  |   do_syscall_64+0x48/0x150
  |   entry_SYSCALL_64_after_hwframe+0x44/0xa9
  |  RIP: 0033:0x7f3b87efcd0e
  |  Code: 89 54 24 08 e8 a3 f4 ff ff 8b 74 24 0c 48 8b 3c 24 41 89 c0 44 8b 54 24 08 b8 01 01 00 00 89 f4
  |  RSP: 002b:00007f3b87d259f0 EFLAGS: 00000293 ORIG_RAX: 0000000000000101
  |  RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f3b87efcd0e
  |  RDX: 0000000000000000 RSI: 00007f3b87d25a80 RDI: 00000000ffffff9c
  |  RBP: 00007f3b87d25e90 R08: 0000000000000000 R09: 0000000000000000
  |  R10: 0000000000000000 R11: 0000000000000293 R12: 00007ffe188f504e
  |  R13: 00007ffe188f504f R14: 00007f3b87d26700 R15: 0000000000000000
  |  ---[ end trace 24f53ca58db8180a ]---

Since 'cdev_get()' can already fail to obtain a reference, simply move
it over to use 'kobject_get_unless_zero()' instead of 'kobject_get()',
which will cause the racing thread to return -ENXIO if the initialising
thread fails unexpectedly.

Cc: Hillf Danton <hdanton@sina.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: syzbot+82defefbbd8527e1c2cb@syzkaller.appspotmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191219120203.32691-1-will@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kobject: Export kobject_get_unless_zero()

commit c70c176ff8c3ff0ac6ef9a831cd591ea9a66bd1a upstream.

Make the function available for outside use and fortify it against NULL
kobject.

CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.4.209

USB: serial: option: add Telit ME910G1 0x110a composition

commit 0d3010fa442429f8780976758719af05592ff19f upstream.

This patch adds the following Telit ME910G1 composition:

0x110a: tty, tty, tty, rmnet

Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: core: fix check for duplicate endpoints

commit 3e4f8e21c4f27bcf30a48486b9dcc269512b79ff upstream.

Amend the endpoint-descriptor sanity checks to detect all duplicate
endpoint addresses in a configuration.

Commit 0a8fd1346254 ("USB: fix problems with duplicate endpoint
addresses") added a check for duplicate endpoint addresses within a
single alternate setting, but did not look for duplicate addresses in
other interfaces.

The current check would also not detect all duplicate addresses when one
endpoint is as a (bi-directional) control endpoint.

This specifically avoids overwriting the endpoint entries in struct
usb_device when enabling a duplicate endpoint, something which could
potentially lead to crashes or leaks, for example, when endpoints are
later disabled.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191219161016.6695-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

macvlan: do not assume mac_header is set in macvlan_broadcast()

[ Upstream commit 96cc4b69581db68efc9749ef32e9cf8e0160c509 ]

Use of eth_hdr() in tx path is error prone.

Many drivers call skb_reset_mac_header() before using it,
but others do not.

Commit 6d1ccff62780 ("net: reset mac header in dev_start_xmit()")
attempted to fix this generically, but commit d346a3fae3ff
("packet: introduce PACKET_QDISC_BYPASS socket option") brought
back the macvlan bug.

Lets add a new helper, so that tx paths no longer have
to call skb_reset_mac_header() only to get a pointer
to skb->data.

Hopefully we will be able to revert 6d1ccff62780
("net: reset mac header in dev_start_xmit()") and save few cycles
in transmit fast path.

BUG: KASAN: use-after-free in __get_unaligned_cpu32 include/linux/unaligned/packed_struct.h:19 [inline]
BUG: KASAN: use-after-free in mc_hash drivers/net/macvlan.c:251 [inline]
BUG: KASAN: use-after-free in macvlan_broadcast+0x547/0x620 drivers/net/macvlan.c:277
Read of size 4 at addr ffff8880a4932401 by task syz-executor947/9579

CPU: 0 PID: 9579 Comm: syz-executor947 Not tainted 5.5.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x197/0x210 lib/dump_stack.c:118
 print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374
 __kasan_report.cold+0x1b/0x41 mm/kasan/report.c:506
 kasan_report+0x12/0x20 mm/kasan/common.c:639
 __asan_report_load_n_noabort+0xf/0x20 mm/kasan/generic_report.c:145
 __get_unaligned_cpu32 include/linux/unaligned/packed_struct.h:19 [inline]
 mc_hash drivers/net/macvlan.c:251 [inline]
 macvlan_broadcast+0x547/0x620 drivers/net/macvlan.c:277
 macvlan_queue_xmit drivers/net/macvlan.c:520 [inline]
 macvlan_start_xmit+0x402/0x77f drivers/net/macvlan.c:559
 __netdev_start_xmit include/linux/netdevice.h:4447 [inline]
 netdev_start_xmit include/linux/netdevice.h:4461 [inline]
 dev_direct_xmit+0x419/0x630 net/core/dev.c:4079
 packet_direct_xmit+0x1a9/0x250 net/packet/af_packet.c:240
 packet_snd net/packet/af_packet.c:2966 [inline]
 packet_sendmsg+0x260d/0x6220 net/packet/af_packet.c:2991
 sock_sendmsg_nosec net/socket.c:639 [inline]
 sock_sendmsg+0xd7/0x130 net/socket.c:659
 __sys_sendto+0x262/0x380 net/socket.c:1985
 __do_sys_sendto net/socket.c:1997 [inline]
 __se_sys_sendto net/socket.c:1993 [inline]
 __x64_sys_sendto+0xe1/0x1a0 net/socket.c:1993
 do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x442639
Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 5b 10 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007ffc13549e08 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000442639
RDX: 000000000000000e RSI: 0000000020000080 RDI: 0000000000000003
RBP: 0000000000000004 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000403bb0 R14: 0000000000000000 R15: 0000000000000000

Allocated by task 9389:
 save_stack+0x23/0x90 mm/kasan/common.c:72
 set_track mm/kasan/common.c:80 [inline]
 __kasan_kmalloc mm/kasan/common.c:513 [inline]
 __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:486
 kasan_kmalloc+0x9/0x10 mm/kasan/common.c:527
 __do_kmalloc mm/slab.c:3656 [inline]
 __kmalloc+0x163/0x770 mm/slab.c:3665
 kmalloc include/linux/slab.h:561 [inline]
 tomoyo_realpath_from_path+0xc5/0x660 security/tomoyo/realpath.c:252
 tomoyo_get_realpath security/tomoyo/file.c:151 [inline]
 tomoyo_path_perm+0x230/0x430 security/tomoyo/file.c:822
 tomoyo_inode_getattr+0x1d/0x30 security/tomoyo/tomoyo.c:129
 security_inode_getattr+0xf2/0x150 security/security.c:1222
 vfs_getattr+0x25/0x70 fs/stat.c:115
 vfs_statx_fd+0x71/0xc0 fs/stat.c:145
 vfs_fstat include/linux/fs.h:3265 [inline]
 __do_sys_newfstat+0x9b/0x120 fs/stat.c:378
 __se_sys_newfstat fs/stat.c:375 [inline]
 __x64_sys_newfstat+0x54/0x80 fs/stat.c:375
 do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Freed by task 9389:
 save_stack+0x23/0x90 mm/kasan/common.c:72
 set_track mm/kasan/common.c:80 [inline]
 kasan_set_free_info mm/kasan/common.c:335 [inline]
 __kasan_slab_free+0x102/0x150 mm/kasan/common.c:474
 kasan_slab_free+0xe/0x10 mm/kasan/common.c:483
 __cache_free mm/slab.c:3426 [inline]
 kfree+0x10a/0x2c0 mm/slab.c:3757
 tomoyo_realpath_from_path+0x1a7/0x660 security/tomoyo/realpath.c:289
 tomoyo_get_realpath security/tomoyo/file.c:151 [inline]
 tomoyo_path_perm+0x230/0x430 security/tomoyo/file.c:822
 tomoyo_inode_getattr+0x1d/0x30 security/tomoyo/tomoyo.c:129
 security_inode_getattr+0xf2/0x150 security/security.c:1222
 vfs_getattr+0x25/0x70 fs/stat.c:115
 vfs_statx_fd+0x71/0xc0 fs/stat.c:145
 vfs_fstat include/linux/fs.h:3265 [inline]
 __do_sys_newfstat+0x9b/0x120 fs/stat.c:378
 __se_sys_newfstat fs/stat.c:375 [inline]
 __x64_sys_newfstat+0x54/0x80 fs/stat.c:375
 do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

The buggy address belongs to the object at ffff8880a4932000
 which belongs to the cache kmalloc-4k of size 4096
The buggy address is located 1025 bytes inside of
 4096-byte region [ffff8880a4932000, ffff8880a4933000)
The buggy address belongs to the page:
page:ffffea0002924c80 refcount:1 mapcount:0 mapping:ffff8880aa402000 index:0x0 compound_mapcount: 0
raw: 00fffe0000010200 ffffea0002846208 ffffea00028f3888 ffff8880aa402000
raw: 0000000000000000 ffff8880a4932000 0000000100000001 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff8880a4932300: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff8880a4932380: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8880a4932400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
                   ^
 ffff8880a4932480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff8880a4932500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb

Fixes: b863ceb7ddce ("[NET]: Add macvlan driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vxlan: fix tos value before xmit

[ Upstream commit 71130f29979c7c7956b040673e6b9d5643003176 ]

Before ip_tunnel_ecn_encap() and udp_tunnel_xmit_skb() we should filter
tos value by RT_TOS() instead of using config tos directly.

vxlan_get_route() would filter the tos to fl4.flowi4_tos but we didn't
return it back, as geneve_get_v4_rt() did. So we have to use RT_TOS()
directly in function ip_tunnel_ecn_encap().

Fixes: 206aaafcd279 ("VXLAN: Use IP Tunnels tunnel ENC encap API")
Fixes: 1400615d64cf ("vxlan: allow setting ipv6 traffic class")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vlan: fix memory leak in vlan_dev_set_egress_priority

[ Upstream commit 9bbd917e0bec9aebdbd0c8dbc966caec15eb33e9 ]

There are few cases where the ndo_uninit() handler might be not
called if an error happens while device is initialized.

Since vlan_newlink() calls vlan_changelink() before
trying to register the netdevice, we need to make sure
vlan_dev_uninit() has been called at least once,
or we might leak allocated memory.

BUG: memory leak
unreferenced object 0xffff888122a206c0 (size 32):
  comm "syz-executor511", pid 7124, jiffies 4294950399 (age 32.240s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 61 73 00 00 00 00 00 00 00 00  ......as........
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<000000000eb3bb85>] kmemleak_alloc_recursive include/linux/kmemleak.h:43 [inline]
    [<000000000eb3bb85>] slab_post_alloc_hook mm/slab.h:586 [inline]
    [<000000000eb3bb85>] slab_alloc mm/slab.c:3320 [inline]
    [<000000000eb3bb85>] kmem_cache_alloc_trace+0x145/0x2c0 mm/slab.c:3549
    [<000000007b99f620>] kmalloc include/linux/slab.h:556 [inline]
    [<000000007b99f620>] vlan_dev_set_egress_priority+0xcc/0x150 net/8021q/vlan_dev.c:194
    [<000000007b0cb745>] vlan_changelink+0xd6/0x140 net/8021q/vlan_netlink.c:126
    [<0000000065aba83a>] vlan_newlink+0x135/0x200 net/8021q/vlan_netlink.c:181
    [<00000000fb5dd7a2>] __rtnl_newlink+0x89a/0xb80 net/core/rtnetlink.c:3305
    [<00000000ae4273a1>] rtnl_newlink+0x4e/0x80 net/core/rtnetlink.c:3363
    [<00000000decab39f>] rtnetlink_rcv_msg+0x178/0x4b0 net/core/rtnetlink.c:5424
    [<00000000accba4ee>] netlink_rcv_skb+0x61/0x170 net/netlink/af_netlink.c:2477
    [<00000000319fe20f>] rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5442
    [<00000000d51938dc>] netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
    [<00000000d51938dc>] netlink_unicast+0x223/0x310 net/netlink/af_netlink.c:1328
    [<00000000e539ac79>] netlink_sendmsg+0x2c0/0x570 net/netlink/af_netlink.c:1917
    [<000000006250c27e>] sock_sendmsg_nosec net/socket.c:639 [inline]
    [<000000006250c27e>] sock_sendmsg+0x54/0x70 net/socket.c:659
    [<00000000e2a156d1>] ____sys_sendmsg+0x2d0/0x300 net/socket.c:2330
    [<000000008c87466e>] ___sys_sendmsg+0x8a/0xd0 net/socket.c:2384
    [<00000000110e3054>] __sys_sendmsg+0x80/0xf0 net/socket.c:2417
    [<00000000d71077c8>] __do_sys_sendmsg net/socket.c:2426 [inline]
    [<00000000d71077c8>] __se_sys_sendmsg net/socket.c:2424 [inline]
    [<00000000d71077c8>] __x64_sys_sendmsg+0x23/0x30 net/socket.c:2424

Fixe: 07b5b17e157b ("[VLAN]: Use rtnl_link API")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vlan: vlan_changelink() should propagate errors

[ Upstream commit eb8ef2a3c50092bb018077c047b8dba1ce0e78e3 ]

Both vlan_dev_change_flags() and vlan_dev_set_egress_priority()
can return an error. vlan_changelink() should not ignore them.

Fixes: 07b5b17e157b ("[VLAN]: Use rtnl_link API")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: fix "old stuff" D-SACK causing SACK to be treated as D-SACK

[ Upstream commit c9655008e7845bcfdaac10a1ed8554ec167aea88 ]

When we receive a D-SACK, where the sequence number satisfies:
undo_marker <= start_seq < end_seq <= prior_snd_una
we consider this is a valid D-SACK and tcp_is_sackblock_valid()
returns true, then this D-SACK is discarded as "old stuff",
but the variable first_sack_index is not marked as negative
in tcp_sacktag_write_queue().

If this D-SACK also carries a SACK that needs to be processed
(for example, the previous SACK segment was lost), this SACK
will be treated as a D-SACK in the following processing of
tcp_sacktag_write_queue(), which will eventually lead to
incorrect updates of undo_retrans and reordering.

Fixes: fd6dad616d4f ("[TCP]: Earlier SACK block verification & simplify access to them")
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sctp: free cmd->obj.chunk for the unprocessed SCTP_CMD_REPLY

[ Upstream commit be7a7729207797476b6666f046d765bdf9630407 ]

This patch is to fix a memleak caused by no place to free cmd->obj.chunk
for the unprocessed SCTP_CMD_REPLY. This issue occurs when failing to
process a cmd while there're still SCTP_CMD_REPLY cmds on the cmd seq
with an allocated chunk in cmd->obj.chunk.

So fix it by freeing cmd->obj.chunk for each SCTP_CMD_REPLY cmd left on
the cmd seq when any cmd returns error. While at it, also remove 'nomem'
label.

Reported-by: syzbot+107c4aff5f392bf1517f@syzkaller.appspotmail.com
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pkt_sched: fq: do not accept silly TCA_FQ_QUANTUM

[ Upstream commit d9e15a2733067c9328fb56d98fe8e574fa19ec31 ]

As diagnosed by Florian :

If TCA_FQ_QUANTUM is set to 0x80000000, fq_deueue()
can loop forever in :

if (f->credit <= 0) {
  f->credit += q->quantum;
  goto begin;
}

... because f->credit is either 0 or -2147483648.

Let's limit TCA_FQ_QUANTUM to no more than 1 << 20 :
This max value should limit risks of breaking user setups
while fixing this bug.

Fixes: afe4fd062416 ("pkt_sched: fq: Fair Queue packet scheduler")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Diagnosed-by: Florian Westphal <fw@strlen.de>
Reported-by: syzbot+dc9071cc5a85950bdfce@syzkaller.appspotmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: usb: lan78xx: fix possible skb leak

[ Upstream commit 47240ba0cd09bb6fe6db9889582048324999dfa4 ]

If skb_linearize() fails, we need to free the skb.

TSO makes skb bigger, and this bug might be the reason
Raspberry Pi 3B+ users had to disable TSO.

Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: stmmac: dwmac-sunxi: Allow all RGMII modes

[ Upstream commit 52cc73e5404c7ba0cbfc50cb4c265108c84b3d5a ]

Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.

Fixes: af0bd4e9ba80 ("net: stmmac: sunxi platform extensions for GMAC in Allwinner A20 SoC's")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)

[ Upstream commit af1c0e4e00f3cc76cb136ebf2e2c04e8b6446285 ]

When a frame with NULL DSAP is received, llc_station_rcv is called.
In turn, llc_stat_ev_rx_null_dsap_xid_c is called to check if it is a NULL
XID frame. The return statement of llc_stat_ev_rx_null_dsap_xid_c returns 1
when the incoming frame is not a NULL XID frame and 0 otherwise. Hence, a
NULL XID response is returned unexpectedly, e.g. when the incoming frame is
a NULL TEST command.

To fix the error, simply remove the conditional operator.

A similar error in llc_stat_ev_rx_null_dsap_test_c is also fixed.

Signed-off-by: Chan Shu Tak, Alex <alexchan@task.com.hk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

parisc: Fix compiler warnings in debug_core.c

[ Upstream commit 75cf9797006a3a9f29a3a25c1febd6842a4a9eb2 ]

Fix this compiler warning:
kernel/debug/debug_core.c: In function ‘kgdb_cpu_enter’:
arch/parisc/include/asm/cmpxchg.h:48:3: warning: value computed is not used [-Wunused-value]
   48 |  ((__typeof__(*(ptr)))__xchg((unsigned long)(x), (ptr), sizeof(*(ptr))))
arch/parisc/include/asm/atomic.h:78:30: note: in expansion of macro ‘xchg’
   78 | #define atomic_xchg(v, new) (xchg(&((v)->counter), new))
      |                              ^~~~
kernel/debug/debug_core.c:596:4: note: in expansion of macro ‘atomic_xchg’
  596 |    atomic_xchg(&kgdb_active, cpu);
      |    ^~~~~~~~~~~

Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kconfig: don't crash on NULL expressions in expr_eq()

[ Upstream commit 272a72103012862e3a24ea06635253ead0b6e808 ]

NULL expressions are taken to always be true, as implemented by the
expr_is_yes() macro and by several other functions in expr.c. As such,
they ought to be valid inputs to expr_eq(), which compares two
expressions.

Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

regulator: rn5t618: fix module aliases

[ Upstream commit 62a1923cc8fe095912e6213ed5de27abbf1de77e ]

platform device aliases were missing, preventing
autoloading of module.

Fixes: 811b700630ff ("regulator: rn5t618: add driver for Ricoh RN5T618 regulators")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20191211221600.29438-1-andreas@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: wm8962: fix lambda value

[ Upstream commit 556672d75ff486e0b6786056da624131679e0576 ]

According to user manual, it is required that FLL_LAMBDA > 0
in all cases (Integer and Franctional modes).

Fixes: 9a76f1ff6e29 ("ASoC: Add initial WM8962 CODEC driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1576065442-19763-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rfkill: Fix incorrect check to avoid NULL pointer dereference

[ Upstream commit 6fc232db9e8cd50b9b83534de9cd91ace711b2d7 ]

In rfkill_register, the struct rfkill pointer is first derefernced
and then checked for NULL. This patch removes the BUG_ON and returns
an error to the caller in case rfkill is NULL.

Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Link: https://lore.kernel.org/r/20191215153409.21696-1-pakki001@umn.edu
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: usb: lan78xx: Fix error message format specifier

[ Upstream commit 858ce8ca62ea1530f2779d0e3f934b0176e663c3 ]

Display the return code as decimal integer.

Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bnx2x: Fix logic to get total no. of PFs per engine

[ Upstream commit ee699f89bdbaa19c399804504241b5c531b48888 ]

Driver doesn't calculate total number of PFs configured on a
given engine correctly which messed up resources in the PFs
loaded on that engine, leading driver to exceed configuration
of resources (like vlan filters etc.) beyond the limit per
engine, which ended up with asserts from the firmware.

Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bnx2x: Do not handle requests from VFs after parity

[ Upstream commit 7113f796bbbced2470cd6d7379d50d7a7a78bf34 ]

Parity error from the hardware will cause PF to lose the state
of their VFs due to PF's internal reload and hardware reset following
the parity error. Restrict any configuration request from the VFs after
the parity as it could cause unexpected hardware behavior, only way
for VFs to recover would be to trigger FLR on VFs and reload them.

Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc: Ensure that swiotlb buffer is allocated from low memory

[ Upstream commit 8fabc623238e68b3ac63c0dd1657bf86c1fa33af ]

Some powerpc platforms (e.g. 85xx) limit DMA-able memory way below 4G.
If a system has more physical memory than this limit, the swiotlb
buffer is not addressable because it is allocated from memblock using
top-down mode.

Force memblock to bottom-up mode before calling swiotlb_init() to
ensure that the swiotlb buffer is DMA-able.

Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191204123524.22919-1-rppt@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: am437x-gp/epos-evm: fix panel compatible

[ Upstream commit c6b16761c6908d3dc167a0a566578b4b0b972905 ]

The LCD panel on AM4 GP EVMs and ePOS boards seems to be
osd070t1718-19ts. The current dts files say osd057T0559-34ts. Possibly
the panel has changed since the early EVMs, or there has been a mistake
with the panel type.

Update the DT files accordingly.

Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: uapi: Avoid undefined left-shift in xt_sctp.h

[ Upstream commit 164166558aacea01b99c8c8ffb710d930405ba69 ]

With 'bytes(__u32)' being 32, a left-shift of 31 may happen which is
undefined for the signed 32-bit value 1. Avoid this by declaring 1 as
unsigned.

Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: vexpress: Set-up shared OPP table instead of individual for each CPU

[ Upstream commit 2a76352ad2cc6b78e58f737714879cc860903802 ]

Currently we add individual copy of same OPP table for each CPU within
the cluster. This is redundant and doesn't reflect the reality.

We can't use core cpumask to set policy->cpus in ve_spc_cpufreq_init()
anymore as it gets called via cpuhp_cpufreq_online()->cpufreq_online()
->cpufreq_driver->init() and the cpumask gets updated upon CPU hotplug
operations. It also may cause issues when the vexpress_spc_cpufreq
driver is built as a module.

Since ve_spc_clk_init is built-in device initcall, we should be able to
use the same topology_core_cpumask to set the opp sharing cpumask via
dev_pm_opp_set_sharing_cpus and use the same later in the driver via
dev_pm_opp_get_sharing_cpus.

Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: ctnetlink: netns exit must wait for callbacks

[ Upstream commit 18a110b022a5c02e7dc9f6109d0bd93e58ac6ebb ]

Curtis Taylor and Jon Maxwell reported and debugged a crash on 3.10
based kernel.

Crash occurs in ctnetlink_conntrack_events because net->nfnl socket is
NULL.  The nfnl socket was set to NULL by netns destruction running on
another cpu.

The exiting network namespace calls the relevant destructors in the
following order:

1. ctnetlink_net_exit_batch

This nulls out the event callback pointer in struct netns.

2. nfnetlink_net_exit_batch

This nulls net->nfnl socket and frees it.

3. nf_conntrack_cleanup_net_list

This removes all remaining conntrack entries.

This is order is correct. The only explanation for the crash so ar is:

cpu1: conntrack is dying, eviction occurs:
 -> nf_ct_delete()
   -> nf_conntrack_event_report \
     -> nf_conntrack_eventmask_report
       -> notify->fcn() (== ctnetlink_conntrack_events).

cpu1: a. fetches rcu protected pointer to obtain ctnetlink event callback.
      b. gets interrupted.
 cpu2: runs netns exit handlers:
     a runs ctnetlink destructor, event cb pointer set to NULL.
     b runs nfnetlink destructor, nfnl socket is closed and set to NULL.
cpu1: c. resumes and trips over NULL net->nfnl.

Problem appears to be that ctnetlink_net_exit_batch only prevents future
callers of nf_conntrack_eventmask_report() from obtaining the callback.
It doesn't wait of other cpus that might have already obtained the
callbacks address.

I don't see anything in upstream kernels that would prevent similar
crash: We need to wait for all cpus to have exited the event callback.

Fixes: 9592a5c01e79dbc59eb56fa ("netfilter: ctnetlink: netns support")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

locking/spinlock/debug: Fix various data races

[ Upstream commit 1a365e822372ba24c9da0822bc583894f6f3d821 ]

This fixes various data races in spinlock_debug. By testing with KCSAN,
it is observable that the console gets spammed with data races reports,
suggesting these are extremely frequent.

Example data race report:

  read to 0xffff8ab24f403c48 of 4 bytes by task 221 on cpu 2:
   debug_spin_lock_before kernel/locking/spinlock_debug.c:85 [inline]
   do_raw_spin_lock+0x9b/0x210 kernel/locking/spinlock_debug.c:112
   __raw_spin_lock include/linux/spinlock_api_smp.h:143 [inline]
   _raw_spin_lock+0x39/0x40 kernel/locking/spinlock.c:151
   spin_lock include/linux/spinlock.h:338 [inline]
   get_partial_node.isra.0.part.0+0x32/0x2f0 mm/slub.c:1873
   get_partial_node mm/slub.c:1870 [inline]
  <snip>

  write to 0xffff8ab24f403c48 of 4 bytes by task 167 on cpu 3:
   debug_spin_unlock kernel/locking/spinlock_debug.c:103 [inline]
   do_raw_spin_unlock+0xc9/0x1a0 kernel/locking/spinlock_debug.c:138
   __raw_spin_unlock_irqrestore include/linux/spinlock_api_smp.h:159 [inline]
   _raw_spin_unlock_irqrestore+0x2d/0x50 kernel/locking/spinlock.c:191
   spin_unlock_irqrestore include/linux/spinlock.h:393 [inline]
   free_debug_processing+0x1b3/0x210 mm/slub.c:1214
   __slab_free+0x292/0x400 mm/slub.c:2864
  <snip>

As a side-effect, with KCSAN, this eventually locks up the console, most
likely due to deadlock, e.g. .. -> printk lock -> spinlock_debug ->
KCSAN detects data race -> kcsan_print_report() -> printk lock ->
deadlock.

This fix will 1) avoid the data races, and 2) allow using lock debugging
together with KCSAN.

Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Marco Elver <elver@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Link: https://lkml.kernel.org/r/20191120155715.28089-1-elver@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pstore/ram: Write new dumps to start of recycled zones

[ Upstream commit 9e5f1c19800b808a37fb9815a26d382132c26c3d ]

The ram_core.c routines treat przs as circular buffers. When writing a
new crash dump, the old buffer needs to be cleared so that the new dump
doesn't end up in the wrong place (i.e. at the end).

The solution to this problem is to reset the circular buffer state before
writing a new Oops dump.

Signed-off-by: Aleksandr Yashkin <a.yashkin@inango-systems.com>
Signed-off-by: Nikolay Merinov <n.merinov@inango-systems.com>
Signed-off-by: Ariel Gilman <a.gilman@inango-systems.com>
Link: https://lore.kernel.org/r/20191223133816.28155-1-n.merinov@inango-systems.com
Fixes: 896fc1f0c4c6 ("pstore/ram: Switch to persistent_ram routines")
[kees: backport to v4.9]
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>