OSDN Git Service
Qu Wenruo [Mon, 31 May 2021 08:50:46 +0000 (16:50 +0800)]
btrfs: make page Ordered bit to be subpage compatible
This involves the following modification:
- Ordered extent creation
This is done in process_one_page(), now PAGE_SET_ORDERED will call
subpage helper to do the work.
- endio functions
This is done in btrfs_mark_ordered_io_finished().
- btrfs_invalidatepage()
- btrfs_cleanup_ordered_extents()
Use the subpage page helper, and add an extra branch to exit if the
locked page have covered the full range.
Now the usage of page Ordered flag for ordered extent accounting is fully
subpage compatible.
Tested-by: Ritesh Harjani <riteshh@linux.ibm.com> # [ppc64]
Tested-by: Anand Jain <anand.jain@oracle.com> # [aarch64]
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 31 May 2021 08:50:45 +0000 (16:50 +0800)]
btrfs: introduce helpers for subpage ordered status
This patch introduces the following functions to handle btrfs subpage
ordered (Private2) status:
- btrfs_subpage_set_ordered()
- btrfs_subpage_clear_ordered()
- btrfs_subpage_test_ordered()
These helpers can only be called when the range is ensured to be
inside the page.
- btrfs_page_set_ordered()
- btrfs_page_clear_ordered()
- btrfs_page_test_ordered()
These helpers can handle both regular sector size and subpage without
problem.
These functions are here to coordinate btrfs_invalidatepage() with
btrfs_writepage_endio_finish_ordered(), to make sure only one of those
functions can finish the ordered extent.
Tested-by: Ritesh Harjani <riteshh@linux.ibm.com> # [ppc64]
Tested-by: Anand Jain <anand.jain@oracle.com> # [aarch64]
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 31 May 2021 08:50:44 +0000 (16:50 +0800)]
btrfs: make process_one_page() to handle subpage locking
Introduce a new data inodes specific subpage member, writers, to record
how many sectors are under page lock for delalloc writing.
This member acts pretty much the same as readers, except it's only for
delalloc writes.
This is important for delalloc code to trace which page can really be
freed, as we have cases like run_delalloc_nocow() where we may exit
processing nocow range inside a page, but need to exit to do cow half
way.
In that case, we need a way to determine if we can really unlock a full
page.
With the new btrfs_subpage::writers, there is a new requirement:
- Page locked by process_one_page() must be unlocked by
process_one_page()
There are still tons of call sites manually lock and unlock a page,
without updating btrfs_subpage::writers.
So if we lock a page through process_one_page() then it must be
unlocked by process_one_page() to keep btrfs_subpage::writers
consistent.
This will be handled in next patch.
Tested-by: Ritesh Harjani <riteshh@linux.ibm.com> # [ppc64]
Tested-by: Anand Jain <anand.jain@oracle.com> # [aarch64]
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 31 May 2021 08:50:43 +0000 (16:50 +0800)]
btrfs: make end_bio_extent_writepage() to be subpage compatible
Now in end_bio_extent_writepage(), the only subpage incompatible code is
the end_page_writeback().
Just call the subpage helpers.
Tested-by: Ritesh Harjani <riteshh@linux.ibm.com> # [ppc64]
Tested-by: Anand Jain <anand.jain@oracle.com> # [aarch64]
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 31 May 2021 08:50:42 +0000 (16:50 +0800)]
btrfs: make __process_pages_contig() to handle subpage dirty/error/writeback status
For __process_pages_contig() and process_one_page(), to handle subpage
we only need to pass bytenr in and call subpage helpers to handle
dirty/error/writeback status.
Tested-by: Ritesh Harjani <riteshh@linux.ibm.com> # [ppc64]
Tested-by: Anand Jain <anand.jain@oracle.com> # [aarch64]
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 31 May 2021 08:50:41 +0000 (16:50 +0800)]
btrfs: make btrfs_dirty_pages() to be subpage compatible
Since the extent io tree operations in btrfs_dirty_pages() are already
subpage compatible, we only need to make the page status update to use
subpage helpers.
Tested-by: Ritesh Harjani <riteshh@linux.ibm.com> # [ppc64]
Tested-by: Anand Jain <anand.jain@oracle.com> # [aarch64]
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 31 May 2021 08:50:40 +0000 (16:50 +0800)]
btrfs: only require sector size alignment for end_bio_extent_writepage()
Just like read page, for subpage support we only require sector size
alignment.
So change the error message condition to only require sector alignment.
This should not affect existing code, as for regular sectorsize ==
PAGE_SIZE case, we are still requiring page alignment.
Tested-by: Ritesh Harjani <riteshh@linux.ibm.com> # [ppc64]
Tested-by: Anand Jain <anand.jain@oracle.com> # [aarch64]
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 31 May 2021 08:50:39 +0000 (16:50 +0800)]
btrfs: provide btrfs_page_clamp_*() helpers
In the coming subpage RW supports, there are a lot of page status update
calls which need to be converted to subpage compatible version, which
needs @start and @len.
Some call sites already have such @start/@len and are already in
page range, like various endio functions.
But there are also call sites which need to clamp the range for subpage
case, like btrfs_dirty_pagse() and __process_contig_pages().
Here we introduce new helpers, btrfs_page_clamp_*(), to do and only do the
clamp for subpage version.
Although in theory all existing btrfs_page_*() calls can be converted to
use btrfs_page_clamp_*() directly, but that would make us to do
unnecessary clamp operations.
Tested-by: Ritesh Harjani <riteshh@linux.ibm.com> # [ppc64]
Tested-by: Anand Jain <anand.jain@oracle.com> # [aarch64]
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 31 May 2021 08:50:38 +0000 (16:50 +0800)]
btrfs: refactor page status update into process_one_page()
In __process_pages_contig() we update page status according to page_ops.
That update process is a bunch of 'if' branches, which lie inside
two loops, this makes it pretty hard to expand for later subpage
operations.
So this patch will extract these operations into its own function,
process_one_pages().
Also since we're refactoring __process_pages_contig(), also move the new
helper and __process_pages_contig() before the first caller of them, to
remove the forward declaration.
Tested-by: Ritesh Harjani <riteshh@linux.ibm.com> # [ppc64]
Tested-by: Anand Jain <anand.jain@oracle.com> # [aarch64]
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 31 May 2021 08:50:37 +0000 (16:50 +0800)]
btrfs: pass bytenr directly to __process_pages_contig()
As a preparation for incoming subpage support, we need bytenr passed to
__process_pages_contig() directly, not the current page index.
So change the parameter and all callers to pass bytenr in.
With the modification, here we need to replace the old @index_ret with
@processed_end for __process_pages_contig(), but this brings a small
problem.
Normally we follow the inclusive return value, meaning @processed_end
should be the last byte we processed.
If parameter @start is 0, and we failed to lock any page, then we would
return @processed_end as -1, causing more problems for
__unlock_for_delalloc().
So here for @processed_end, we use two different return value patterns.
If we have locked any page, @processed_end will be the last byte of
locked page.
Or it will be @start otherwise.
This change will impact lock_delalloc_pages(), so it needs to check
@processed_end to only unlock the range if we have locked any.
Tested-by: Ritesh Harjani <riteshh@linux.ibm.com> # [ppc64]
Tested-by: Anand Jain <anand.jain@oracle.com> # [aarch64]
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 18 May 2021 07:09:41 +0000 (15:09 +0800)]
btrfs: fix hang when run_delalloc_range() failed
[BUG]
When running subpage preparation patches on x86, btrfs/125 will hang
forever with one ordered extent never finished.
[CAUSE]
The test case btrfs/125 itself will always fail as the fix is never merged.
When the test fails at balance, btrfs needs to cleanup the ordered
extent in btrfs_cleanup_ordered_extents() for data reloc inode.
The problem is in the sequence how we cleanup the page Order bit.
Currently it works like:
btrfs_cleanup_ordered_extents()
|- find_get_page();
|- btrfs_page_clear_ordered(page);
| Now the page doesn't have Ordered bit anymore.
| !!! This also includes the first (locked) page !!!
|
|- offset += PAGE_SIZE
| This is to skip the first page
|- __endio_write_update_ordered()
|- btrfs_mark_ordered_io_finished(NULL)
Except the first page, all ordered extents are finished.
Then the locked page is cleaned up in __extent_writepage():
__extent_writepage()
|- If (PageError(page))
|- end_extent_writepage()
|- btrfs_mark_ordered_io_finished(page)
|- if (btrfs_test_page_ordered(page))
|- !!! The page gets skipped !!!
The ordered extent is not decreased as the page doesn't
have ordered bit anymore.
This leaves the ordered extent with bytes_left == sectorsize, thus never
finish.
[FIX]
The fix is to ensure we never clear page Ordered bit without running the
ordered extent accounting.
Here we choose to skip the locked page in
btrfs_cleanup_ordered_extents() so that later end_extent_writepage() can
properly finish the ordered extent.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Wed, 7 Apr 2021 11:22:13 +0000 (19:22 +0800)]
btrfs: rename PagePrivate2 to PageOrdered inside btrfs
Inside btrfs we use Private2 page status to indicate we have an ordered
extent with pending IO for the sector.
But the page status name, Private2, tells us nothing about the bit
itself, so this patch will rename it to Ordered.
And with extra comment about the bit added, so reader who is still
uncertain about the page Ordered status, will find the comment pretty
easily.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 6 Apr 2021 11:54:53 +0000 (19:54 +0800)]
btrfs: refactor btrfs_invalidatepage() for subpage support
This patch will refactor btrfs_invalidatepage() for the incoming subpage
support.
The involved modifications are:
- Use while() loop instead of "goto again;"
- Use single variable to determine whether to delete extent states
Each branch will also have comments why we can or cannot delete the
extent states
- Do qgroup free and extent states deletion per-loop
Current code can only work for PAGE_SIZE == sectorsize case.
This refactor also makes it clear what we do for different sectors:
- Sectors without ordered extent
We're completely safe to remove all extent states for the sector(s)
- Sectors with ordered extent, but no Private2 bit
This means the endio has already been executed, we can't remove all
extent states for the sector(s).
- Sectors with ordere extent, still has Private2 bit
This means we need to decrease the ordered extent accounting.
And then it comes to two different variants:
* We have finished and removed the ordered extent
Then it's the same as "sectors without ordered extent"
* We didn't finished the ordered extent
We can remove some extent states, but not all.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 27 Apr 2021 07:03:40 +0000 (15:03 +0800)]
btrfs: introduce btrfs_lookup_first_ordered_range()
Although we already have btrfs_lookup_first_ordered_extent() and
btrfs_lookup_ordered_extent(), they all have their own limitations:
- btrfs_lookup_ordered_extent() can't do extra range check
It's only designed to lookup any ordered extent before certain bytenr.
- btrfs_lookup_first_ordered_extent() may not return the first ordered
extent in the range
It doesn't ensure the first ordered extent is returned.
The existing callers are only interested in exhausting all ordered
extents in a range, the order is not important.
For incoming btrfs_invalidatepage() refactoring, we need a way to
properly iterate all ordered extents in their bytenr order of a range.
So this patch will introduce a new function,
btrfs_lookup_first_ordered_range(), to do ordered extent with bytenr
order awareness and extra range check.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 6 Apr 2021 00:27:18 +0000 (08:27 +0800)]
btrfs: update comments in btrfs_invalidatepage()
The existing comments in btrfs_invalidatepage() don't really get to the
point, especially for what Private2 is really representing and how the
race avoidance is done.
The truth is, there are only three entrances to do ordered extent
accounting:
- btrfs_writepage_endio_finish_ordered()
- __endio_write_update_ordered()
Those two entrance are just endio functions for dio and buffered
write.
- btrfs_invalidatepage()
But there is a pitfall, in endio functions there is no check on whether
the ordered extent is already accounted.
They just blindly clear the Private2 bit and do the accounting.
So it's all btrfs_invalidatepage()'s responsibility to make sure we
won't do double account for the same sector.
That's why in btrfs_invalidatepage() we have to wait for page writeback,
this will ensure all submitted bios have finished, thus their endio
functions have finished the accounting on the ordered extent.
Then we also check page Private2 to ensure that, we only run ordered
extent accounting on pages who has no bio submitted.
This patch will rework related comments to make it more clear on the
race and how we use wait_on_page_writeback() and Private2 to prevent
double accounting on ordered extent.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Thu, 1 Apr 2021 07:15:06 +0000 (15:15 +0800)]
btrfs: refactor how we finish ordered extent io for endio functions
Btrfs has two endio functions to mark certain io range finished for
ordered extents:
- __endio_write_update_ordered()
This is for direct IO
- btrfs_writepage_endio_finish_ordered()
This for buffered IO.
However they go different routines to handle ordered extent io:
- Whether to iterate through all ordered extents
__endio_write_update_ordered() will but
btrfs_writepage_endio_finish_ordered() will not.
In fact, iterating through all ordered extents will benefit later
subpage support, while for current PAGE_SIZE == sectorsize requirement
this behavior makes no difference.
- Whether to update page Private2 flag
__endio_write_update_ordered() will not update page Private2 flag as
for iomap direct IO, the page can not be even mapped.
While btrfs_writepage_endio_finish_ordered() will clear Private2 to
prevent double accounting against btrfs_invalidatepage().
Those differences are pretty subtle, and the ordered extent iterations
code in callers makes code much harder to read.
So this patch will introduce a new function,
btrfs_mark_ordered_io_finished(), to do the heavy lifting:
- Iterate through all ordered extents in the range
- Do the ordered extent accounting
- Queue the work for finished ordered extent
This function has two new feature:
- Proper underflow detection and recovery
The old underflow detection will only detect the problem, then
continue.
No proper info like root/inode/ordered extent info, nor noisy enough
to be caught by fstests.
Furthermore when underflow happens, the ordered extent will never
finish.
New error detection will reset the bytes_left to 0, do proper
kernel warning, and output extra info including root, ino, ordered
extent range, the underflow value.
- Prevent double accounting based on Private2 flag
Now if we find a range without Private2 flag, we will skip to next
range.
As that means someone else has already finished the accounting of
ordered extent.
This makes no difference for current code, but will be a critical part
for incoming subpage support, as we can call
btrfs_mark_ordered_io_finished() for multiple sectors if they are
beyond inode size.
Thus such double accounting prevention is a key feature for subpage.
Now both endio functions only need to call that new function.
And since the only caller of btrfs_dec_test_first_ordered_pending() is
removed, also remove btrfs_dec_test_first_ordered_pending() completely.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Fri, 22 Jan 2021 06:00:52 +0000 (14:00 +0800)]
btrfs: make Private2 lifespan more consistent
Currently we use page Private2 bit to indicate that we have ordered
extent for the page range.
But the lifespan of it is not consistent, during regular writeback path,
there are two locations to clear the same PagePrivate2:
T ----- Page marked Dirty
|
+ ----- Page marked Private2, through btrfs_run_dealloc_range()
|
+ ----- Page cleared Private2, through btrfs_writepage_cow_fixup()
| in __extent_writepage_io()
| ^^^ Private2 cleared for the first time
|
+ ----- Page marked Writeback, through btrfs_set_range_writeback()
| in __extent_writepage_io().
|
+ ----- Page cleared Private2, through
| btrfs_writepage_endio_finish_ordered()
| ^^^ Private2 cleared for the second time.
|
+ ----- Page cleared Writeback, through
btrfs_writepage_endio_finish_ordered()
Currently PagePrivate2 is mostly to prevent ordered extent accounting
being executed for both endio and invalidatepage.
Thus only the one who cleared page Private2 is responsible for ordered
extent accounting.
But the fact is, in btrfs_writepage_endio_finish_ordered(), page
Private2 is cleared and ordered extent accounting is executed
unconditionally.
The race prevention only happens through btrfs_invalidatepage(), where
we wait for the page writeback first, before checking the Private2 bit.
This means, Private2 is also protected by Writeback bit, and there is no
need for btrfs_writepage_cow_fixup() to clear Priavte2.
This patch will change btrfs_writepage_cow_fixup() to just check
PagePrivate2, not to clear it.
The clearing will happen in either btrfs_invalidatepage() or
btrfs_writepage_endio_finish_ordered().
This makes the Private2 bit easier to understand, just meaning the page
has unfinished ordered extent attached to it.
And this patch is a hard requirement for the incoming refactoring for
how we finished ordered IO for endio context, as the coming patch will
check Private2 to determine if we need to do the ordered extent
accounting. Thus this patch is definitely needed or we will hang due to
unfinished ordered extent.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Thu, 8 Apr 2021 12:32:27 +0000 (20:32 +0800)]
btrfs: pass btrfs_inode to btrfs_writepage_endio_finish_ordered()
There is a pretty bad abuse of btrfs_writepage_endio_finish_ordered() in
end_compressed_bio_write().
It passes compressed pages to btrfs_writepage_endio_finish_ordered(),
which is only supposed to accept inode pages.
Thankfully the important info here is the inode, so let's pass
btrfs_inode directly into btrfs_writepage_endio_finish_ordered(), and
make @page parameter optional.
By this, end_compressed_bio_write() can happily pass page=NULL while
still getting everything done properly.
Also, to cooperate with such modification, replace @page parameter for
trace_btrfs_writepage_end_io_hook() with btrfs_inode.
Although this removes page_index info, the existing start/len should be
enough for most usage.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 27 Apr 2021 04:53:35 +0000 (12:53 +0800)]
btrfs: make subpage metadata write path call its own endio functions
For subpage metadata, we're reusing two functions for subpage metadata
write:
- end_bio_extent_buffer_writepage()
- write_one_eb()
But the truth is, for subpage we just call
end_bio_subpage_eb_writepage() without using any bit in
end_bio_extent_buffer_writepage().
For write_one_eb(), it's pretty similar, but with a small part of code
reused.
There is really no need to pollute the existing code path if we're not
really using most of them.
So this patch will do the following change to separate the subpage
metadata write path from regular write path by:
- Use end_bio_subpage_eb_writepage() directly as endio in
write_one_subpage_eb()
- Directly call write_one_subpage_eb() in submit_eb_subpage()
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Wed, 14 Apr 2021 08:42:15 +0000 (16:42 +0800)]
btrfs: refactor submit_extent_page() to make bio and its flag tracing easier
There is a lot of code inside extent_io.c needs both "struct bio
**bio_ret" and "unsigned long prev_bio_flags", along with some
parameters like "unsigned long bio_flags".
Such strange parameters are here for bio assembly.
For example, we have such inode page layout:
0 4K 8K 12K
|<-- Extent A-->|<- EB->|
Then what we do is:
- Page [0, 4K)
*bio_ret = NULL
So we allocate a new bio to bio_ret,
Add page [0, 4K) to *bio_ret.
- Page [4K, 8K)
*bio_ret != NULL
We found this page is continuous to *bio_ret,
and if we're not at stripe boundary, we
add page [4K, 8K) to *bio_ret.
- Page [8K, 12K)
*bio_ret != NULL
But we found this page is not continuous, so
we submit *bio_ret, then allocate a new bio,
and add page [8K, 12K) to the new bio.
This means we need to record both the bio and its bio_flag, but we
record them manually using those strange parameter list, other than
encapsulating them into their own structure.
So this patch will introduce a new structure, btrfs_bio_ctrl, to record
both the bio, and its bio_flags.
Also, in above case, for all pages added to the bio, we need to check if
the new page crosses stripe boundary. This check itself can be time
consuming, and we don't really need to do that for each page.
This patch also integrates the stripe boundary check into btrfs_bio_ctrl.
When a new bio is allocated, the stripe and ordered extent boundary is
also calculated, so no matter how large the bio will be, we only
calculate the boundaries once, to save some CPU time.
The following functions/structures are affected:
- struct extent_page_data
Replace its bio pointer with structure btrfs_bio_ctrl (embedded
structure, not pointer)
- end_write_bio()
- flush_write_bio()
Just change how bio is fetched
- btrfs_bio_add_page()
Use pre-calculated boundaries instead of re-calculating them.
And use @bio_ctrl to replace @bio and @prev_bio_flags.
- calc_bio_boundaries()
New function
- submit_extent_page() callers
- btrfs_do_readpage() callers
- contiguous_readpages() callers
To Use @bio_ctrl to replace @bio and @prev_bio_flags, and how to grab
bio.
- btrfs_bio_fits_in_ordered_extent()
Removed, as now the ordered extent size limit is done at bio
allocation time, no need to check for each page range.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 13 Apr 2021 10:00:47 +0000 (18:00 +0800)]
btrfs: allow btrfs_bio_fits_in_stripe() to accept bio without any page
Function btrfs_bio_fits_in_stripe() now requires a bio with at least one
page added. Or btrfs_get_chunk_map() will fail with -ENOENT.
But in fact this requirement is not needed at all, as we can just pass
sectorsize for btrfs_get_chunk_map().
This tiny behavior change is important for later subpage refactoring on
submit_extent_page().
As for 64K page size, we can have a page range with pgoff=0 and size=64K.
If the logical bytenr is just 16K before the stripe boundary, we have to
split the page range into two bios.
This means, we must check page range against stripe boundary, even adding
the range to an empty bio.
This tiny refactoring is for the incoming changes, but on its own,
regular sectorsize == PAGE_SIZE is not affected anyway.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 13 Apr 2021 09:58:48 +0000 (17:58 +0800)]
btrfs: remove the unused parameter @len for btrfs_bio_fits_in_stripe()
The parameter @len is not really used in btrfs_bio_fits_in_stripe(),
just remove it.
It got removed in
420343131970 ("btrfs: let callers of
btrfs_get_io_geometry pass the em"), before that btrfs_get_chunk_map
utilized it.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 13 Apr 2021 06:23:14 +0000 (14:23 +0800)]
btrfs: make free space cache size consistent across different PAGE_SIZE
Currently free space cache inode size is determined by two factors:
- block group size
- PAGE_SIZE
This means, for the same sized block groups, with different PAGE_SIZE,
it will result in different inode sizes.
This will not be a good thing for subpage support, so change the
requirement for PAGE_SIZE to sectorsize.
Now for the same 4K sectorsize btrfs, it should result the same inode
size no matter what the PAGE_SIZE is.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Thu, 22 Apr 2021 11:02:46 +0000 (19:02 +0800)]
btrfs: scrub: fix subpage repair error caused by hard coded PAGE_SIZE
[BUG]
For the following file layout, scrub will not be able to repair all
these two repairable error, but in fact make one corruption even
unrepairable:
inode offset 0 4k 8K
Mirror 1 |XXXXXX| |
Mirror 2 | |XXXXXX|
[CAUSE]
The root cause is the hard coded PAGE_SIZE, which makes scrub repair to
go crazy for subpage.
For above case, when reading the first sector, we use PAGE_SIZE other
than sectorsize to read, which makes us to read the full range [0, 64K).
In fact, after 8K there may be no data at all, we can just get some
garbage.
Then when doing the repair, we also writeback a full page from mirror 2,
this means, we will also writeback the corrupted data in mirror 2 back
to mirror 1, leaving the range [4K, 8K) unrepairable.
[FIX]
This patch will modify the following PAGE_SIZE use with sectorsize:
- scrub_print_warning_inode()
Remove the min() and replace PAGE_SIZE with sectorsize.
The min() makes no sense, as csum is done for the full sector with
padding.
This fixes a bug that subpage report extra length like:
checksum error at logical
298844160 on dev /dev/mapper/arm_nvme-test,
physical
575668224, root 5, inode 257, offset 0, length 12288, links 1 (path: file)
Where the error is only 1 sector.
- scrub_handle_errored_block()
Comments with PAGE|page involved, all changed to sector.
- scrub_setup_recheck_block()
- scrub_repair_page_from_good_copy()
- scrub_add_page_to_wr_bio()
- scrub_wr_submit()
- scrub_add_page_to_rd_bio()
- scrub_block_complete()
Replace PAGE_SIZE with sectorsize.
This solves several problems where we read/write extra range for
subpage case.
RAID56 code is excluded intentionally, as RAID56 has extra PAGE_SIZE
usage, and is not really safe enough.
Thus we will reject RAID56 for subpage in later commit.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Nikolay Borisov [Mon, 31 May 2021 07:37:03 +0000 (10:37 +0300)]
btrfs: use list_last_entry in add_falloc_range
Instead of calling list_entry with head->prev simply call
list_last_entry which makes it obvious which member of the list is
being referred. This allows to remove the extra 'prev' pointer.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Anand Jain [Sat, 29 May 2021 09:48:36 +0000 (17:48 +0800)]
btrfs: fix comment about max_out in btrfs_compress_pages
Commit
e5d74902362f ("btrfs: derive maximum output size in the
compression implementation") removed @max_out argument in
btrfs_compress_pages() but its comment remained, remove it.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Anand Jain [Sat, 29 May 2021 09:48:35 +0000 (17:48 +0800)]
btrfs: optimize variables size in btrfs_submit_compressed_write
Patch "btrfs: reduce compressed_bio member's types" reduced some
member's size. Function arguments @len, @compressed_len and @nr_pages
can be declared as unsigned int.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Anand Jain [Sat, 29 May 2021 09:48:34 +0000 (17:48 +0800)]
btrfs: optimize variables size in btrfs_submit_compressed_read
Patch "btrfs: reduce compressed_bio member's types" reduced some
member's size. Declare the variables @compressed_len, @nr_pages and
@pg_index size as an unsigned int in the function
btrfs_submit_compressed_read.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Anand Jain [Sat, 29 May 2021 09:48:33 +0000 (17:48 +0800)]
btrfs: reduce the variable size to fit nr_pages
Patch "btrfs: reduce compressed_bio member's types" reduced the
@nr_pages size to unsigned int, its cascading effects are updated here.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Fri, 28 May 2021 10:37:32 +0000 (11:37 +0100)]
btrfs: avoid unnecessary logging of xattrs during fast fsyncs
When logging an inode we always log all its xattrs, so that we are able
to figure out which ones should be deleted during log replay. However this
is unnecessary when we are doing a fast fsync and no xattrs were added,
changed or deleted since the last time we logged the inode in the current
transaction.
So skip the logging of xattrs when the inode was previously logged in the
current transaction and no xattrs were added, changed or deleted. If any
changes to xattrs happened, than the inode has BTRFS_INODE_COPY_EVERYTHING
set in its runtime flags and the xattrs get logged. This saves time on
scanning for xattrs, allocating memory, COWing log tree extent buffers and
adding more lock contention on the extent buffers when there are multiple
tasks logging in parallel.
The use of xattrs is common when using ACLs, some applications, or when
using security modules like SELinux where every inode gets a security
xattr added to it.
The following test script, using fio, was used on a box with 12 cores, 64G
of RAM, a NVMe device and the default non-debug kernel config from Debian.
It uses 8 concurrent jobs each writing in blocks of 64K to its own 4G file,
each file with a single xattr of 50 bytes (about the same size for an ACL
or SELinux xattr), doing random buffered writes with an fsync after each
write.
$ cat test.sh
#!/bin/bash
DEV=/dev/nvme0n1
MNT=/mnt/test
MOUNT_OPTIONS="-o ssd"
MKFS_OPTIONS="-d single -m single"
NUM_JOBS=8
FILE_SIZE=4G
cat <<EOF > /tmp/fio-job.ini
[writers]
rw=randwrite
fsync=1
fallocate=none
group_reporting=1
direct=0
bs=64K
ioengine=sync
size=$FILE_SIZE
directory=$MNT
numjobs=$NUM_JOBS
EOF
echo "performance" | \
tee /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor
mkfs.btrfs -f $MKFS_OPTIONS $DEV > /dev/null
mount $MOUNT_OPTIONS $DEV $MNT
echo "Creating files before fio runs, each with 1 xattr of 50 bytes"
for ((i = 0; i < $NUM_JOBS; i++)); do
path="$MNT/writers.$i.0"
truncate -s $FILE_SIZE $path
setfattr -n user.xa1 -v $(printf '%0.sX' $(seq 50)) $path
done
fio /tmp/fio-job.ini
umount $MNT
fio output before this change:
WRITE: bw=120MiB/s (126MB/s), 120MiB/s-120MiB/s (126MB/s-126MB/s), io=32.0GiB (34.4GB), run=272145-272145msec
fio output after this change:
WRITE: bw=142MiB/s (149MB/s), 142MiB/s-142MiB/s (149MB/s-149MB/s), io=32.0GiB (34.4GB), run=230408-230408msec
+16.8% throughput, -16.6% runtime
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Fri, 14 May 2021 19:21:27 +0000 (21:21 +0200)]
btrfs: add device delete cancel
Accept device name "cancel" as a request to cancel running device
deletion operation. The string is literal, in case there's a real device
named "cancel", pass it as full absolute path or as "./cancel"
This works for v1 and v2 ioctls when the device is specified by name.
Moving chunks from the device uses relocation, use the conditional
exclusive operation start and cancellation helpers
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Tue, 18 May 2021 19:12:33 +0000 (21:12 +0200)]
btrfs: add cancellation to resize
Accept literal string "cancel" as resize operation and interpret that
as a request to cancel the running operation. If it's running, wait
until it finishes current work and return ECANCELED.
Shrinking resize uses relocation to move the chunks away, use the
conditional exclusive operation start and cancellation helpers.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Fri, 14 May 2021 19:32:44 +0000 (21:32 +0200)]
btrfs: add wrapper for conditional start of exclusive operation
To support optional cancellation of some operations, add helper that will
wrap all the combinations. In normal mode it's same as
btrfs_exclop_start, in cancellation mode it checks if it's already
running and request cancellation and waits until completion.
The error codes can be returned to to user space and semantics is not
changed, adding ECANCELED. This should be evaluated as an error and that
the operation has not completed and the operation should be restarted
or the filesystem status reviewed.
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Tue, 18 May 2021 19:05:52 +0000 (21:05 +0200)]
btrfs: introduce try-lock semantics for exclusive op start
Add try-lock for exclusive operation start to allow callers to do more
checks. The same operation must already be running. The try-lock and
unlock must pair and are a substitute for btrfs_exclop_start, thus it
must also pair with btrfs_exclop_finish to release the exclop context.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Mon, 17 May 2021 22:37:36 +0000 (00:37 +0200)]
btrfs: add cancellable chunk relocation support
Add support code that will allow canceling relocation on the chunk
granularity. This is different and independent of balance, that also
uses relocation but is a higher level operation and manages it's own
state and pause/cancellation requests.
Relocation is used for resize (shrink) and device deletion so this will
be a common point to implement cancellation for both. The context is
entirely in btrfs_relocate_block_group and btrfs_recover_relocation,
enclosing one chunk relocation. The status bit is set and unset between
the chunks. As relocation can take long, the effects may not be
immediate and the request and actual action can slightly race.
The fs_info::reloc_cancel_req is only supposed to be increased and does
not pair with decrement like fs_info::balance_cancel_req.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Fri, 14 May 2021 15:42:30 +0000 (17:42 +0200)]
btrfs: protect exclusive_operation by super_lock
The exclusive operation is now atomically checked and set using bit
operations. Switch it to protection by spinlock. The super block lock is
not frequently used and adding a new lock seems like an overkill so it
should be safe to reuse it.
The reason to use spinlock is to enhance the locking context so more
checks can be done, eg. allowing the same exclusive operation enter
the exclop section and cancel the running one. This will be used for
resize and device delete.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Mon, 21 Sep 2020 20:07:14 +0000 (22:07 +0200)]
btrfs: clean up header members offsets in write helpers
Move header offsetof() to the expression that calculates the address so
it's part of get_eb_offset_in_page where the 2nd parameter is the member
offset.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Mon, 21 Sep 2020 20:07:14 +0000 (22:07 +0200)]
btrfs: simplify eb checksum verification in btrfs_validate_metadata_buffer
The verification copies the calculated checksum bytes to a temporary
buffer but this is not necessary. We can map the eb header on the first
page and use the checksum bytes directly.
This saves at least one function call and boundary checks so it could
lead to a minor performance improvement.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Mon, 21 Sep 2020 19:58:14 +0000 (21:58 +0200)]
btrfs: remove extra sb::s_id from message in btrfs_validate_metadata_buffer
The s_id is already printed by message helpers.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Mon, 14 Oct 2019 12:38:33 +0000 (14:38 +0200)]
btrfs: reduce compressed_bio members' types
Several members of compressed_bio are of type that's unnecessarily big
for the values that they'd hold:
- the size of the uncompressed and compressed data is 128K now, we can
keep is as int
- same for number of pages
- the compress type fits to a byte
- the errors is 0/1
The size of the unpatched structure is 80 bytes with several holes.
Reordering nr_pages next to the pages the hole after pending_bios is
filled and the resulting size is 56 bytes. This keeps the csums array
aligned to 8 bytes, which is nice. Further size optimizations may be
possible but right now it looks good to me:
struct compressed_bio {
refcount_t pending_bios; /* 0 4 */
unsigned int nr_pages; /* 4 4 */
struct page * * compressed_pages; /* 8 8 */
struct inode * inode; /* 16 8 */
u64 start; /* 24 8 */
unsigned int len; /* 32 4 */
unsigned int compressed_len; /* 36 4 */
u8 compress_type; /* 40 1 */
u8 errors; /* 41 1 */
/* XXX 2 bytes hole, try to pack */
int mirror_num; /* 44 4 */
struct bio * orig_bio; /* 48 8 */
u8 sums[]; /* 56 0 */
/* size: 56, cachelines: 1, members: 12 */
/* sum members: 54, holes: 1, sum holes: 2 */
/* last cacheline: 56 bytes */
};
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Tue, 15 Sep 2020 19:10:03 +0000 (21:10 +0200)]
btrfs: document byte swap optimization of root_item::flags accessors
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 28 Nov 2019 14:37:46 +0000 (15:37 +0100)]
btrfs: scrub: factor out common scrub_stripe constraints
There are common values set for the stripe constraints, some of them
are already factored out. Do that for increment and mirror_num as well.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Tue, 7 Jul 2020 16:38:05 +0000 (18:38 +0200)]
btrfs: clear log tree recovering status if starting transaction fails
When a log recovery is in progress, lots of operations have to take that
into account, so we keep this status per tree during the operation. Long
time ago error handling revamp patch
79787eaab461 ("btrfs: replace many
BUG_ONs with proper error handling") removed clearing of the status in
an error branch. Add it back as was intended in
e02119d5a7b4 ("Btrfs:
Add a write ahead tree log to optimize synchronous operations").
There are probably no visible effects, log replay is done only during
mount and if it fails all structures are cleared so the stale status
won't be kept.
Fixes:
79787eaab461 ("btrfs: replace many BUG_ONs with proper error handling")
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Tue, 7 Jul 2020 16:30:06 +0000 (18:30 +0200)]
btrfs: clear defrag status of a root if starting transaction fails
The defrag loop processes leaves in batches and starting transaction for
each. The whole defragmentation on a given root is protected by a bit
but in case the transaction fails, the bit is not cleared
In case the transaction fails the bit would prevent starting
defragmentation again, so make sure it's cleared.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Fri, 7 May 2021 18:00:14 +0000 (20:00 +0200)]
btrfs: sysfs: fix format string for some discard stats
The type of discard_bitmap_bytes and discard_extent_bytes is u64 so the
format should be %llu, though the actual values would hardly ever
overflow to negative values.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Thu, 20 May 2021 15:21:31 +0000 (11:21 -0400)]
btrfs: always abort the transaction if we abort a trans handle
While stress testing our error handling I noticed that sometimes we
would still commit the transaction even though we had aborted the
transaction.
Currently we track if a trans handle has dirtied any metadata, and if it
hasn't we mark the filesystem as having an error (so no new transactions
can be started), but we will allow the current transaction to complete
as we do not mark the transaction itself as having been aborted.
This sounds good in theory, but we were not properly tracking IO errors
in btrfs_finish_ordered_io, and thus committing the transaction with
bogus free space data. This isn't necessarily a problem per-se with the
free space cache, as the other guards in place would have kept us from
accepting the free space cache as valid, but highlights a real world
case where we had a bug and could have corrupted the filesystem because
of it.
This "skip abort on empty trans handle" is nice in theory, but assumes
we have perfect error handling everywhere, which we clearly do not.
Also we do not allow further transactions to be started, so all this
does is save the last transaction that was happening, which doesn't
necessarily gain us anything other than the potential for real
corruption.
Remove this particular bit of code, if we decide we need to abort the
transaction then abort the current one and keep us from doing real harm
to the file system, regardless of whether this specific trans handle
dirtied anything or not.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Mon, 24 May 2021 10:35:55 +0000 (11:35 +0100)]
btrfs: don't set the full sync flag when truncation does not touch extents
At btrfs_truncate() where we truncate the inode either to the same size
or to a smaller size, we always set the full sync flag on the inode.
This is needed in case the truncation drops or trims any file extent items
that start beyond or cross the new inode size, so that the next fsync
drops all inode items from the log and scans again the fs/subvolume tree
to find all items that must be logged.
However if the truncation does not drop or trims any file extent items, we
do not need to set the full sync flag and force the next fsync to use the
slow code path. So do not set the full sync flag in such cases.
One use case where it is frequent to do truncations that do not change
the inode size and do not drop any extents (no prealloc extents beyond
i_size) is when running Microsoft's SQL Server inside a Docker container.
One example workload is the one Philipp Fent reported recently, in the
thread with a link below. In this workload a large number of fsyncs are
preceded by such truncate operations.
After this change I constantly get the runtime for that workload from
Philipp to be reduced by about -12%, for example from 184 seconds down
to 162 seconds.
Link: https://lore.kernel.org/linux-btrfs/93c4600e-5263-5cba-adf0-6f47526e7561@in.tum.de/
Tested-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Mon, 24 May 2021 10:35:54 +0000 (11:35 +0100)]
btrfs: fix misleading and incomplete comment of btrfs_truncate()
The comment at the top of btrfs_truncate() mentions that csum items are
dropped or truncated to the new i_size, but this is wrong and non sense,
as they are unrelated to the i_size and are located in the csums tree and
not on a tree with inode items (fs/subvolume tree or a log tree). Instead
that claim applies to file extent items, so fix the comment to refer to
them instead.
While at it make the whole comment for the function more descriptive and
follow the kernel doc style.
Tested-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Fri, 21 May 2021 20:44:09 +0000 (16:44 -0400)]
btrfs: abort transaction if we fail to update the delayed inode
If we fail to update the delayed inode we need to abort the transaction,
because we could leave an inode with the improper counts or some other
such corruption behind.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Fri, 21 May 2021 20:44:08 +0000 (16:44 -0400)]
btrfs: fix error handling in __btrfs_update_delayed_inode
If we get an error while looking up the inode item we'll simply bail
without cleaning up the delayed node. This results in this style of
warning happening on commit:
WARNING: CPU: 0 PID: 76403 at fs/btrfs/delayed-inode.c:1365 btrfs_assert_delayed_root_empty+0x5b/0x90
CPU: 0 PID: 76403 Comm: fsstress Tainted: G W 5.13.0-rc1+ #373
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
RIP: 0010:btrfs_assert_delayed_root_empty+0x5b/0x90
RSP: 0018:
ffffb8bb815a7e50 EFLAGS:
00010286
RAX:
0000000000000000 RBX:
ffff95d6d07e1888 RCX:
ffff95d6c0fa3000
RDX:
0000000000000002 RSI:
000000000029e91c RDI:
ffff95d6c0fc8060
RBP:
ffff95d6c0fc8060 R08:
00008d6d701a2c1d R09:
0000000000000000
R10:
ffff95d6d1760ea0 R11:
0000000000000001 R12:
ffff95d6c15a4d00
R13:
ffff95d6c0fa3000 R14:
0000000000000000 R15:
ffffb8bb815a7e90
FS:
00007f490e8dbb80(0000) GS:
ffff95d73bc00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007f6e75555cb0 CR3:
00000001101ce001 CR4:
0000000000370ef0
Call Trace:
btrfs_commit_transaction+0x43c/0xb00
? finish_wait+0x80/0x80
? vfs_fsync_range+0x90/0x90
iterate_supers+0x8c/0x100
ksys_sync+0x50/0x90
__do_sys_sync+0xa/0x10
do_syscall_64+0x3d/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Because the iref isn't dropped and this leaves an elevated node->count,
so any release just re-queues it onto the delayed inodes list. Fix this
by going to the out label to handle the proper cleanup of the delayed
node.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Fri, 21 May 2021 20:44:07 +0000 (16:44 -0400)]
btrfs: make btrfs_release_delayed_iref handle the !iref case
Right now we only cleanup the delayed iref if we have
BTRFS_DELAYED_NODE_DEL_IREF set on the node. However we have some error
conditions that need to cleanup the iref if it still exists, so to make
this code cleaner move the test_bit into btrfs_release_delayed_iref
itself and unconditionally call it in each of the cases instead.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Wed, 9 Oct 2019 11:58:13 +0000 (13:58 +0200)]
btrfs: scrub: per-device bandwidth control
Add sysfs interface to limit io during scrub. We relied on the ionice
interface to do that, eg. the idle class let the system usable while
scrub was running. This has changed when mq-deadline got widespread and
did not implement the scheduling classes. That was a CFQ thing that got
deleted. We've got numerous complaints from users about degraded
performance.
Currently only BFQ supports that but it's not a common scheduler and we
can't ask everybody to switch to it.
Alternatively the cgroup io limiting can be used but that also a
non-trivial setup (v2 required, the controller must be enabled on the
system). This can still be used if desired.
Other ideas that have been explored: piggy-back on ionice (that is set
per-process and is accessible) and interpret the class and classdata as
bandwidth limits, but this does not have enough flexibility as there are
only 8 allowed and we'd have to map fixed limits to each value. Also
adjusting the value would need to lookup the process that currently runs
scrub on the given device, and the value is not sticky so would have to
be adjusted each time scrub runs.
Running out of options, sysfs does not look that bad:
- it's accessible from scripts, or udev rules
- the name is similar to what MD-RAID has
(/proc/sys/dev/raid/speed_limit_max or /sys/block/mdX/md/sync_speed_max)
- the value is sticky at least for filesystem mount time
- adjusting the value has immediate effect
- sysfs is available in constrained environments (eg. system rescue)
- the limit also applies to device replace
Sysfs:
- raw value is in bytes
- values written to the file accept suffixes like K, M
- file is in the per-device directory /sys/fs/btrfs/FSID/devinfo/DEVID/scrub_speed_max
- 0 means use default priority of IO
The scheduler is a simple deadline one and the accuracy is up to nearest
128K.
Signed-off-by: David Sterba <dsterba@suse.com>
Johannes Thumshirn [Tue, 18 May 2021 15:40:29 +0000 (00:40 +0900)]
btrfs: zoned: factor out zoned device lookup
To be able to construct a zone append bio we need to look up the
btrfs_device. The code doing the chunk map lookup to get the device is
present in btrfs_submit_compressed_write and submit_extent_page.
Factor out the lookup calls into a helper and use it in the submission
paths.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Tian Tao [Wed, 5 May 2021 01:26:28 +0000 (09:26 +0800)]
btrfs: return EAGAIN if defrag is canceled
When inode defrag is canceled, the error is set to EAGAIN but then
overwritten by number of defragmented bytes. As this would hide the
error, rather return EAGAIN. This does not harm 'btrfs fi defrag', it
will print the error and continue to next file (as it does in for any
other error).
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 3 May 2021 02:08:56 +0000 (10:08 +0800)]
btrfs: remove io_failure_record::in_validation
The io_failure_record::in_validation was introduced to handle failed bio
which cross several sectors. In such case, we still need to verify
which sectors are corrupted.
But since we've changed the way how we handle corrupted sectors, by only
submitting repair for each corrupted sector, there is no need for extra
validation any more.
This patch will cleanup all io_failure_record::in_validation related
code.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 3 May 2021 02:08:55 +0000 (10:08 +0800)]
btrfs: submit read time repair only for each corrupted sector
Currently btrfs_submit_read_repair() has some extra check on whether the
failed bio needs extra validation for repair. But we can avoid all
these extra mechanisms if we submit the repair for each sector.
By this, each read repair can be easily handled without the need to
verify which sector is corrupted.
This will also benefit subpage, as one subpage bvec can contain several
sectors, making the extra verification more complex.
So this patch will:
- Introduce repair_one_sector()
The main code submitting repair, which is more or less the same as old
btrfs_submit_read_repair().
But this time, it only repairs one sector.
- Make btrfs_submit_read_repair() to handle sectors differently
There are 3 different cases:
* Good sector
We need to release the page and extent, set the range uptodate.
* Bad sector and failed to submit repair bio
We need to release the page and extent, but not set the range
uptodate.
* Bad sector but repair bio submitted
The page and extent release will be handled by the submitted repair
bio. Nothing needs to be done.
Since btrfs_submit_read_repair() will handle the page and extent
release now, we need to skip to next bvec even we hit some error.
- Change the lifespan of @uptodate in end_bio_extent_readpage()
Since now btrfs_submit_read_repair() will handle the full bvec
which contains any corruption, we don't need to bother updating
@uptodate bit anymore.
Just let @uptodate to be local variable inside the main loop,
so that any error from one bvec won't affect later bvec.
- Only export btrfs_repair_one_sector(), unexport
btrfs_submit_read_repair()
The only outside caller for read repair is DIO, which already submits
its repair for just one sector.
Only export btrfs_repair_one_sector() for DIO.
This patch will focus on the change on the repair path, the extra
validation code is still kept as is, and will be cleaned up later.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 3 May 2021 02:08:54 +0000 (10:08 +0800)]
btrfs: make btrfs_verify_data_csum() to return a bitmap
This will provide the basis for later per-sector repair for subpage,
while still keeping the existing code happy.
As if all csums match, the return value will be 0, same as now.
Only when csum mismatches, the return value is different.
The new return value will be a bitmap, for 4K sectorsize and 4K page
size, it will be either 1, instead of the -EIO (which is not used
directly by the callers, no effective change).
But for 4K sectorsize and 64K page size, aka subpage case, since the
bvec can contain multiple sectors, knowing which sectors are corrupted
will allow us to submit repair only for corrupted sectors.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Johannes Thumshirn [Mon, 10 May 2021 15:17:26 +0000 (00:17 +0900)]
btrfs: rename check_async_write and let it return bool
The 'check_async_write' function is a helper used in
'btrfs_submit_metadata_bio' and it checks if asynchronous writing can be
used for metadata.
Make the function return bool and get rid of the local variable async in
btrfs_submit_metadata_bio storing the result of check_async_write's
tests.
As this is touching all function call sites, also rename it to
should_async_write as this is more in line with the naming we use.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Johannes Thumshirn [Fri, 30 Apr 2021 13:34:18 +0000 (15:34 +0200)]
btrfs: zoned: bail out if we can't read a reliable write pointer
If we can't read a reliable write pointer from a sequential zone fail
creating the block group with an I/O error.
Also if the read write pointer is beyond the end of the respective zone,
fail the creation of the block group on this zone with an I/O error.
While this could also happen in real world scenarios with misbehaving
drives, this issue addresses a problem uncovered by fstests' test case
generic/475.
CC: stable@vger.kernel.org # 5.12+
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Fri, 30 Apr 2021 13:34:17 +0000 (15:34 +0200)]
btrfs: zoned: print message when zone sanity check type fails
This extends patch
784daf2b9628 ("btrfs: zoned: sanity check zone
type"), the message was supposed to be there but was lost during merge.
We want to make the error noticeable so add it.
Fixes:
784daf2b9628 ("btrfs: zoned: sanity check zone type")
CC: stable@vger.kernel.org # 5.12+
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 28 Apr 2021 17:38:48 +0000 (13:38 -0400)]
btrfs: handle preemptive delalloc flushing slightly differently
If we decide to flush delalloc from the preemptive flusher, we really do
not want to wait on ordered extents, as it gains us nothing. However
there was logic to go ahead and wait on ordered extents if there was
more ordered bytes than delalloc bytes. We do not want this behavior,
so pass through whether this flushing is for preemption, and do not wait
for ordered extents if that's the case. Also break out of the shrink
loop after the first flushing, as we just want to one shot shrink
delalloc.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 28 Apr 2021 17:38:47 +0000 (13:38 -0400)]
btrfs: only ignore delalloc if delalloc is much smaller than ordered
While testing heavy delalloc workloads I noticed that sometimes we'd
just stop preemptively flushing when we had loads of delalloc available
to flush. This is because we skip preemptive flushing if delalloc <=
ordered. However if we start with say 4gib of delalloc, and we flush
2gib of that, we'll stop flushing there, when we still have 2gib of
delalloc to flush.
Instead adjust the ordered bytes down by half, this way if 2/3 of our
outstanding delalloc reservations are tied up by ordered extents we
don't bother preemptive flushing, as we're getting close to the state
where we need to wait on ordered extents.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 28 Apr 2021 17:38:46 +0000 (13:38 -0400)]
btrfs: don't include the global rsv size in the preemptive used amount
When deciding if we should preemptively flush space, we will add in the
amount of space used by all block rsvs. However this also includes the
global block rsv, which isn't flushable so shouldn't be accounted for in
this calculation. If we decide to use ->bytes_may_use in our used
calculation we need to subtract the global rsv size from this amount so
it most closely matches the flushable space.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 28 Apr 2021 17:38:45 +0000 (13:38 -0400)]
btrfs: use the global rsv size in the preemptive thresh calculation
We calculate the amount of "free" space available for normal
reservations by taking the total space and subtracting out the hard used
space, which is readonly, used, and reserved space.
However we weren't taking into account the global block rsv, which is
essentially hard used space. Handle this by subtracting it from the
available free space, so that our threshold more closely mirrors
reality.
We need to do the check because it's possible that the global_rsv_size +
used is > total_bytes, sometimes the global reserve can end up being
calculated as larger than the available size (think small filesystems
where we only have the original 8MiB chunk of metadata). It doesn't
usually happen, but that can get us into trouble so this is safer.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 28 Apr 2021 17:38:44 +0000 (13:38 -0400)]
btrfs: take into account global rsv in need_preemptive_reclaim
Global rsv can't be used for normal allocations, and for very full file
systems we can decide to try and async flush constantly even though
there's really not a lot of space to reclaim. Deal with this by
including the global block rsv size in the "total used" calculation.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 28 Apr 2021 17:38:43 +0000 (13:38 -0400)]
btrfs: only clamp the first time we have to start flushing
We were clamping the threshold for preemptive reclaim any time we added
a ticket to wait on, which if we have a lot of threads means we'd
essentially max out the clamp the first time we start to flush.
Instead of doing this, simply do it every time we have to start
flushing, this will make us ramp up gradually instead of going to max
clamping as soon as we start needing to do flushing.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 28 Apr 2021 17:38:42 +0000 (13:38 -0400)]
btrfs: check worker before need_preemptive_reclaim
need_preemptive_reclaim() does some calculations, which aren't heavy,
but if we're already running preemptive reclaim there's no reason to do
them at all, so re-order the checks so that we don't do the calculation
if we're already doing reclaim.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Su Yue [Sun, 25 Apr 2021 08:35:04 +0000 (16:35 +0800)]
btrfs: remove stale comment for argument seed of btrfs_find_device
Commit
b2598edf8b36 ("btrfs: remove unused argument seed from
btrfs_find_device") removed the argument seed from btrfs_find_device
but forgot the comment, so remove it.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Su Yue <l@damenly.su>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Goldwyn Rodrigues [Thu, 8 Apr 2021 12:40:25 +0000 (07:40 -0500)]
btrfs: correct try_lock_extent() usage in read_extent_buffer_subpage()
try_lock_extent() returns 1 on success or 0 for failure and not an error
code. If try_lock_extent() fails, read_extent_buffer_subpage() returns
zero indicating subpage extent read success.
Return EAGAIN/EWOULDBLOCK if try_lock_extent() fails in locking the
extent.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Linus Torvalds [Sun, 20 Jun 2021 22:03:15 +0000 (15:03 -0700)]
Linux 5.13-rc7
Linus Torvalds [Sun, 20 Jun 2021 16:44:52 +0000 (09:44 -0700)]
Merge tag 'sched_urgent_for_v5.13_rc6' of git://git./linux/kernel/git/tip/tip
Pull scheduler fix from Borislav Petkov:
"A single fix to restore fairness between control groups with equal
priority"
* tag 'sched_urgent_for_v5.13_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Correctly insert cfs_rq's to list on unthrottle
Linus Torvalds [Sun, 20 Jun 2021 16:38:14 +0000 (09:38 -0700)]
Merge tag 'irq_urgent_for_v5.13_rc6' of git://git./linux/kernel/git/tip/tip
Pull irq fix from Borislav Petkov:
"A single fix for GICv3 to not take an interrupt in an NMI context"
* tag 'irq_urgent_for_v5.13_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Workaround inconsistent PMR setting on NMI entry
Linus Torvalds [Sun, 20 Jun 2021 16:09:58 +0000 (09:09 -0700)]
Merge tag 'x86_urgent_for_v5.13_rc6' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
"A first set of urgent fixes to the FPU/XSTATE handling mess^W code.
(There's a lot more in the pipe):
- Prevent corruption of the XSTATE buffer in signal handling by
validating what is being copied from userspace first.
- Invalidate other task's preserved FPU registers on XRSTOR failure
(#PF) because latter can still modify some of them.
- Restore the proper PKRU value in case userspace modified it
- Reset FPU state when signal restoring fails
Other:
- Map EFI boot services data memory as encrypted in a SEV guest so
that the guest can access it and actually boot properly
- Two SGX correctness fixes: proper resources freeing and a NUMA fix"
* tag 'x86_urgent_for_v5.13_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Avoid truncating memblocks for SGX memory
x86/sgx: Add missing xa_destroy() when virtual EPC is destroyed
x86/fpu: Reset state for all signal restore failures
x86/pkru: Write hardware init value to PKRU when xstate is init
x86/process: Check PF_KTHREAD and not current->mm for kernel threads
x86/fpu: Invalidate FPU state after a failed XRSTOR from a user buffer
x86/fpu: Prevent state corruption in __fpu__restore_sig()
x86/ioremap: Map EFI-reserved memory as encrypted for SEV
Linus Torvalds [Sat, 19 Jun 2021 23:50:23 +0000 (16:50 -0700)]
Merge tag 'powerpc-5.13-6' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fix initrd corruption caused by our recent change to use relative jump
labels.
Fix a crash using perf record on systems without a hardware PMU
backend.
Rework our 64-bit signal handling slighty to make it more closely
match the old behaviour, after the recent change to use unsafe user
accessors.
Thanks to Anastasia Kovaleva, Athira Rajeev, Christophe Leroy, Daniel
Axtens, Greg Kurz, and Roman Bolshakov"
* tag 'powerpc-5.13-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/perf: Fix crash in perf_instruction_pointer() when ppmu is not set
powerpc: Fix initrd corruption with relative jump labels
powerpc/signal64: Copy siginfo before changing regs->nip
powerpc/mem: Add back missing header to fix 'no previous prototype' error
Linus Torvalds [Sat, 19 Jun 2021 21:50:43 +0000 (14:50 -0700)]
Merge tag 'perf-tools-fixes-for-v5.13-2021-06-19' of git://git./linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix refcount usage when processing PERF_RECORD_KSYMBOL.
- 'perf stat' metric group fixes.
- Fix 'perf test' non-bash issue with stat bpf counters.
- Update unistd, in.h and socket.h with the kernel sources, silencing
perf build warnings.
* tag 'perf-tools-fixes-for-v5.13-2021-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
tools headers UAPI: Sync linux/in.h copy with the kernel sources
tools headers UAPI: Sync asm-generic/unistd.h with the kernel original
perf beauty: Update copy of linux/socket.h with the kernel sources
perf test: Fix non-bash issue with stat bpf counters
perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL
perf metricgroup: Return error code from metricgroup__add_metric_sys_event_iter()
perf metricgroup: Fix find_evsel_group() event selector
Linus Torvalds [Sat, 19 Jun 2021 15:45:34 +0000 (08:45 -0700)]
Merge tag 'riscv-for-linus-5.13-rc7' of git://git./linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A build fix to always build modules with the 'medany' code model, as
the module loader doesn't support 'medlow'.
- A Kconfig warning fix for the SiFive errata.
- A pair of fixes that for regressions to the recent memory layout
changes.
- A fix for the FU740 device tree.
* tag 'riscv-for-linus-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: dts: fu740: fix cache-controller interrupts
riscv: Ensure BPF_JIT_REGION_START aligned with PMD size
riscv: kasan: Fix MODULES_VADDR evaluation due to local variables' name
riscv: sifive: fix Kconfig errata warning
riscv32: Use medany C model for modules
Linus Torvalds [Sat, 19 Jun 2021 15:39:13 +0000 (08:39 -0700)]
Merge tag 's390-5.13-4' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Fix zcrypt ioctl hang due to AP queue msg counter dropping below 0
when pending requests are purged.
- Two fixes for the machine check handler in the entry code.
* tag 's390-5.13-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ap: Fix hanging ioctl caused by wrong msg counter
s390/mcck: fix invalid KVM guest condition check
s390/mcck: fix calculation of SIE critical section size
Arnaldo Carvalho de Melo [Sat, 19 Jun 2021 13:15:22 +0000 (10:15 -0300)]
tools headers UAPI: Sync linux/in.h copy with the kernel sources
To pick the changes in:
321827477360934d ("icmp: don't send out ICMP messages with a source address of 0.0.0.0")
That don't result in any change in tooling, as INADDR_ are not used to
generate id->string tables used by 'perf trace'.
This addresses this build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/in.h' differs from latest version at 'include/uapi/linux/in.h'
diff -u tools/include/uapi/linux/in.h include/uapi/linux/in.h
Cc: David S. Miller <davem@davemloft.net>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Sat, 19 Jun 2021 13:11:46 +0000 (10:11 -0300)]
tools headers UAPI: Sync asm-generic/unistd.h with the kernel original
To pick the changes in:
8b1462b67f23da54 ("quota: finish disable quotactl_path syscall")
Those headers are used in some arches to generate the syscall table used
in 'perf trace' to translate syscall numbers into strings.
This addresses this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/asm-generic/unistd.h' differs from latest version at 'include/uapi/asm-generic/unistd.h'
diff -u tools/include/uapi/asm-generic/unistd.h include/uapi/asm-generic/unistd.h
Cc: Jan Kara <jack@suse.cz>
Cc: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Sat, 19 Jun 2021 13:09:08 +0000 (10:09 -0300)]
perf beauty: Update copy of linux/socket.h with the kernel sources
To pick the changes in:
ea6932d70e223e02 ("net: make get_net_ns return error if NET_NS is disabled")
That don't result in any changes in the tables generated from that
header.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/perf/trace/beauty/include/linux/socket.h' differs from latest version at 'include/linux/socket.h'
diff -u tools/perf/trace/beauty/include/linux/socket.h include/linux/socket.h
Cc: Changbin Du <changbin.du@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ian Rogers [Thu, 17 Jun 2021 18:42:13 +0000 (11:42 -0700)]
perf test: Fix non-bash issue with stat bpf counters
$(( .. )) is a bash feature but the test's interpreter is !/bin/sh,
switch the code to use expr.
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: bpf@vger.kernel.org
Link: http://lore.kernel.org/lkml/20210617184216.2075588-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Riccardo Mancini [Sat, 12 Jun 2021 17:37:48 +0000 (19:37 +0200)]
perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL
ASan reported a memory leak of BPF-related ksymbols map and dso. The
leak is caused by refount never reaching 0, due to missing __put calls
in the function machine__process_ksymbol_register.
Once the dso is inserted in the map, dso__put() should be called
(map__new2() increases the refcount to 2).
The same thing applies for the map when it's inserted into maps
(maps__insert() increases the refcount to 2).
$ sudo ./perf record -- sleep 5
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.025 MB perf.data (8 samples) ]
=================================================================
==297735==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 6992 byte(s) in 19 object(s) allocated from:
#0 0x4f43c7 in calloc (/home/user/linux/tools/perf/perf+0x4f43c7)
#1 0x8e4e53 in map__new2 /home/user/linux/tools/perf/util/map.c:216:20
#2 0x8cf68c in machine__process_ksymbol_register /home/user/linux/tools/perf/util/machine.c:778:10
[...]
Indirect leak of 8702 byte(s) in 19 object(s) allocated from:
#0 0x4f43c7 in calloc (/home/user/linux/tools/perf/perf+0x4f43c7)
#1 0x8728d7 in dso__new_id /home/user/linux/tools/perf/util/dso.c:1256:20
#2 0x872015 in dso__new /home/user/linux/tools/perf/util/dso.c:1295:9
#3 0x8cf623 in machine__process_ksymbol_register /home/user/linux/tools/perf/util/machine.c:774:21
[...]
Indirect leak of 1520 byte(s) in 19 object(s) allocated from:
#0 0x4f43c7 in calloc (/home/user/linux/tools/perf/perf+0x4f43c7)
#1 0x87b3da in symbol__new /home/user/linux/tools/perf/util/symbol.c:269:23
#2 0x888954 in map__process_kallsym_symbol /home/user/linux/tools/perf/util/symbol.c:710:8
[...]
Indirect leak of 1406 byte(s) in 19 object(s) allocated from:
#0 0x4f43c7 in calloc (/home/user/linux/tools/perf/perf+0x4f43c7)
#1 0x87b3da in symbol__new /home/user/linux/tools/perf/util/symbol.c:269:23
#2 0x8cfbd8 in machine__process_ksymbol_register /home/user/linux/tools/perf/util/machine.c:803:8
[...]
Signed-off-by: Riccardo Mancini <rickyman7@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tommi Rantala <tommi.t.rantala@nokia.com>
Link: http://lore.kernel.org/lkml/20210612173751.188582-1-rickyman7@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
John Garry [Thu, 10 Jun 2021 14:33:00 +0000 (22:33 +0800)]
perf metricgroup: Return error code from metricgroup__add_metric_sys_event_iter()
The error code is not set at all in the sys event iter function.
This may lead to an uninitialized value of "ret" in
metricgroup__add_metric() when no CPU metric is added.
Fix by properly setting the error code.
It is not necessary to init "ret" to 0 in metricgroup__add_metric(), as
if we have no CPU or sys event metric matching, then "has_match" should
be 0 and "ret" is set to -EINVAL.
However gcc cannot detect that it may not have been set after the
map_for_each_metric() loop for CPU metrics, which is strange.
Fixes:
be335ec28efa8 ("perf metricgroup: Support adding metrics for system PMUs")
Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/1623335580-187317-3-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
John Garry [Thu, 10 Jun 2021 14:32:59 +0000 (22:32 +0800)]
perf metricgroup: Fix find_evsel_group() event selector
The following command segfaults on my x86 broadwell:
$ ./perf stat -M frontend_bound,retiring,backend_bound,bad_speculation sleep 1
WARNING: grouped events cpus do not match, disabling group:
anon group { raw 0x10e }
anon group { raw 0x10e }
perf: util/evsel.c:1596: get_group_fd: Assertion `!(!leader->core.fd)' failed.
Aborted (core dumped)
The issue shows itself as a use-after-free in evlist__check_cpu_maps(),
whereby the leader of an event selector (evsel) has been deleted (yet we
still attempt to verify for an evsel).
Fundamentally the problem comes from metricgroup__setup_events() ->
find_evsel_group(), and has developed from the previous fix attempt in
commit
9c880c24cb0d ("perf metricgroup: Fix for metrics containing
duration_time").
The problem now is that the logic in checking if an evsel is in the same
group is subtly broken for the "cycles" event. For the "cycles" event,
the pmu_name is NULL; however the logic in find_evsel_group() may set an
event matched against "cycles" as used, when it should not be.
This leads to a condition where an evsel is set, yet its leader is not.
Fix the check for evsel pmu_name by not matching evsels when either has a
NULL pmu_name.
There is still a pre-existing metric issue whereby the ordering of the
metrics may break the 'stat' function, as discussed at:
https://lore.kernel.org/lkml/
49c6fccb-b716-1bf0-18a6-
cace1cdb66b9@huawei.com/
Fixes:
9c880c24cb0d ("perf metricgroup: Fix for metrics containing duration_time")
Signed-off-by: John Garry <john.garry@huawei.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> # On a Thinkpad T450S
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/1623335580-187317-2-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
David Abdurachmanov [Sun, 13 Jun 2021 00:43:57 +0000 (17:43 -0700)]
riscv: dts: fu740: fix cache-controller interrupts
The order of interrupt numbers is incorrect.
The order for FU740 is: DirError, DataError, DataFail, DirFail
From SiFive FU740-C000 Manual:
19 - L2 Cache DirError
20 - L2 Cache DirFail
21 - L2 Cache DataError
22 - L2 Cache DataFail
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Jisheng Zhang [Fri, 18 Jun 2021 14:09:13 +0000 (22:09 +0800)]
riscv: Ensure BPF_JIT_REGION_START aligned with PMD size
Andreas reported commit
fc8504765ec5 ("riscv: bpf: Avoid breaking W^X")
breaks booting with one kind of defconfig, I reproduced a kernel panic
with the defconfig:
[ 0.138553] Unable to handle kernel paging request at virtual address
ffffffff81201220
[ 0.139159] Oops [#1]
[ 0.139303] Modules linked in:
[ 0.139601] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc5-default+ #1
[ 0.139934] Hardware name: riscv-virtio,qemu (DT)
[ 0.140193] epc : __memset+0xc4/0xfc
[ 0.140416] ra : skb_flow_dissector_init+0x1e/0x82
[ 0.140609] epc :
ffffffff8029806c ra :
ffffffff8033be78 sp :
ffffffe001647da0
[ 0.140878] gp :
ffffffff81134b08 tp :
ffffffe001654380 t0 :
ffffffff81201158
[ 0.141156] t1 :
0000000000000002 t2 :
0000000000000154 s0 :
ffffffe001647dd0
[ 0.141424] s1 :
ffffffff80a43250 a0 :
ffffffff81201220 a1 :
0000000000000000
[ 0.141654] a2 :
000000000000003c a3 :
ffffffff81201258 a4 :
0000000000000064
[ 0.141893] a5 :
ffffffff8029806c a6 :
0000000000000040 a7 :
ffffffffffffffff
[ 0.142126] s2 :
ffffffff81201220 s3 :
0000000000000009 s4 :
ffffffff81135088
[ 0.142353] s5 :
ffffffff81135038 s6 :
ffffffff8080ce80 s7 :
ffffffff80800438
[ 0.142584] s8 :
ffffffff80bc6578 s9 :
0000000000000008 s10:
ffffffff806000ac
[ 0.142810] s11:
0000000000000000 t3 :
fffffffffffffffc t4 :
0000000000000000
[ 0.143042] t5 :
0000000000000155 t6 :
00000000000003ff
[ 0.143220] status:
0000000000000120 badaddr:
ffffffff81201220 cause:
000000000000000f
[ 0.143560] [<
ffffffff8029806c>] __memset+0xc4/0xfc
[ 0.143859] [<
ffffffff8061e984>] init_default_flow_dissectors+0x22/0x60
[ 0.144092] [<
ffffffff800010fc>] do_one_initcall+0x3e/0x168
[ 0.144278] [<
ffffffff80600df0>] kernel_init_freeable+0x1c8/0x224
[ 0.144479] [<
ffffffff804868a8>] kernel_init+0x12/0x110
[ 0.144658] [<
ffffffff800022de>] ret_from_exception+0x0/0xc
[ 0.145124] ---[ end trace
f1e9643daa46d591 ]---
After some investigation, I think I found the root cause: commit
2bfc6cd81bd ("move kernel mapping outside of linear mapping") moves
BPF JIT region after the kernel:
| #define BPF_JIT_REGION_START PFN_ALIGN((unsigned long)&_end)
The &_end is unlikely aligned with PMD size, so the front bpf jit
region sits with part of kernel .data section in one PMD size mapping.
But kernel is mapped in PMD SIZE, when bpf_jit_binary_lock_ro() is
called to make the first bpf jit prog ROX, we will make part of kernel
.data section RO too, so when we write to, for example memset the
.data section, MMU will trigger a store page fault.
To fix the issue, we need to ensure the BPF JIT region is PMD size
aligned. This patch acchieve this goal by restoring the BPF JIT region
to original position, I.E the 128MB before kernel .text section. The
modification to kasan_init.c is inspired by Alexandre.
Fixes:
fc8504765ec5 ("riscv: bpf: Avoid breaking W^X")
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Jisheng Zhang [Fri, 18 Jun 2021 14:01:36 +0000 (22:01 +0800)]
riscv: kasan: Fix MODULES_VADDR evaluation due to local variables' name
commit
2bfc6cd81bd1 ("riscv: Move kernel mapping outside of linear
mapping") makes use of MODULES_VADDR to populate kernel, BPF, modules
mapping. Currently, MODULES_VADDR is defined as below for RV64:
| #define MODULES_VADDR (PFN_ALIGN((unsigned long)&_end) - SZ_2G)
But kasan_init() has two local variables which are also named as _start,
_end, so MODULES_VADDR is evaluated with the local variable _end
rather than the global "_end" as we expected. Fix this issue by
renaming the two local variables.
Fixes:
2bfc6cd81bd1 ("riscv: Move kernel mapping outside of linear mapping")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Linus Torvalds [Sat, 19 Jun 2021 01:55:29 +0000 (18:55 -0700)]
Merge tag 'net-5.13-rc7' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.13-rc7, including fixes from wireless, bpf,
bluetooth, netfilter and can.
Current release - regressions:
- mlxsw: spectrum_qdisc: Pass handle, not band number to find_class()
to fix modifying offloaded qdiscs
- lantiq: net: fix duplicated skb in rx descriptor ring
- rtnetlink: fix regression in bridge VLAN configuration, empty info
is not an error, bot-generated "fix" was not needed
- libbpf: s/rx/tx/ typo on umem->rx_ring_setup_done to fix umem
creation
Current release - new code bugs:
- ethtool: fix NULL pointer dereference during module EEPROM dump via
the new netlink API
- mlx5e: don't update netdev RQs with PTP-RQ, the special purpose
queue should not be visible to the stack
- mlx5e: select special PTP queue only for SKBTX_HW_TSTAMP skbs
- mlx5e: verify dev is present in get devlink port ndo, avoid a panic
Previous releases - regressions:
- neighbour: allow NUD_NOARP entries to be force GCed
- further fixes for fallout from reorg of WiFi locking (staging:
rtl8723bs, mac80211, cfg80211)
- skbuff: fix incorrect msg_zerocopy copy notifications
- mac80211: fix NULL ptr deref for injected rate info
- Revert "net/mlx5: Arm only EQs with EQEs" it may cause missed IRQs
Previous releases - always broken:
- bpf: more speculative execution fixes
- netfilter: nft_fib_ipv6: skip ipv6 packets from any to link-local
- udp: fix race between close() and udp_abort() resulting in a panic
- fix out of bounds when parsing TCP options before packets are
validated (in netfilter: synproxy, tc: sch_cake and mptcp)
- mptcp: improve operation under memory pressure, add missing
wake-ups
- mptcp: fix double-lock/soft lookup in subflow_error_report()
- bridge: fix races (null pointer deref and UAF) in vlan tunnel
egress
- ena: fix DMA mapping function issues in XDP
- rds: fix memory leak in rds_recvmsg
Misc:
- vrf: allow larger MTUs
- icmp: don't send out ICMP messages with a source address of 0.0.0.0
- cdc_ncm: switch to eth%d interface naming"
* tag 'net-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (139 commits)
net: ethernet: fix potential use-after-free in ec_bhf_remove
selftests/net: Add icmp.sh for testing ICMP dummy address responses
icmp: don't send out ICMP messages with a source address of 0.0.0.0
net: ll_temac: Avoid ndo_start_xmit returning NETDEV_TX_BUSY
net: ll_temac: Fix TX BD buffer overwrite
net: ll_temac: Add memory-barriers for TX BD access
net: ll_temac: Make sure to free skb when it is completely used
MAINTAINERS: add Guvenc as SMC maintainer
bnxt_en: Call bnxt_ethtool_free() in bnxt_init_one() error path
bnxt_en: Fix TQM fastpath ring backing store computation
bnxt_en: Rediscover PHY capabilities after firmware reset
cxgb4: fix wrong shift.
mac80211: handle various extensible elements correctly
mac80211: reset profile_periodicity/ema_ap
cfg80211: avoid double free of PMSR request
cfg80211: make certificate generation more robust
mac80211: minstrel_ht: fix sample time check
net: qed: Fix memcpy() overflow of qed_dcbx_params()
net: cdc_eem: fix tx fixup skb leak
net: hamradio: fix memory leak in mkiss_close
...
Linus Torvalds [Fri, 18 Jun 2021 23:39:03 +0000 (16:39 -0700)]
Merge tag 'for-5.13-rc6-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"One more fix, for a space accounting bug in zoned mode. It happens
when a block group is switched back rw->ro and unusable bytes (due to
zoned constraints) are subtracted twice.
It has user visible effects so I consider it important enough for late
-rc inclusion and backport to stable"
* tag 'for-5.13-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zoned: fix negative space_info->bytes_readonly
Linus Torvalds [Fri, 18 Jun 2021 20:54:11 +0000 (13:54 -0700)]
Merge tag 'pci-v5.13-fixes-2' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Clear 64-bit flag for host bridge windows below 4GB to fix a resource
allocation regression added in -rc1 (Punit Agrawal)
- Fix tegra194 MCFG quirk build regressions added in -rc1 (Jon Hunter)
- Avoid secondary bus resets on TI KeyStone C667X devices (Antti
Järvinen)
- Avoid secondary bus resets on some NVIDIA GPUs (Shanker Donthineni)
- Work around FLR erratum on Huawei Intelligent NIC VF (Chiqijun)
- Avoid broken ATS on AMD Navi14 GPU (Evan Quan)
- Trust Broadcom BCM57414 NIC to isolate functions even though it
doesn't advertise ACS support (Sriharsha Basavapatna)
- Work around AMD RS690 BIOSes that don't configure DMA above 4GB
(Mikel Rychliski)
- Fix panic during PIO transfer on Aardvark controller (Pali Rohár)
* tag 'pci-v5.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: aardvark: Fix kernel panic during PIO transfer
PCI: Add AMD RS690 quirk to enable 64-bit DMA
PCI: Add ACS quirk for Broadcom BCM57414 NIC
PCI: Mark AMD Navi14 GPU ATS as broken
PCI: Work around Huawei Intelligent NIC VF FLR erratum
PCI: Mark some NVIDIA GPUs to avoid bus reset
PCI: Mark TI C667X to avoid bus reset
PCI: tegra194: Fix MCFG quirk build regressions
PCI: of: Clear 64-bit flag for non-prefetchable memory below 4GB
Matthew Wilcox (Oracle) [Wed, 16 Jun 2021 21:22:28 +0000 (22:22 +0100)]
afs: Re-enable freezing once a page fault is interrupted
If a task is killed during a page fault, it does not currently call
sb_end_pagefault(), which means that the filesystem cannot be frozen
at any time thereafter. This may be reported by lockdep like this:
====================================
WARNING: fsstress/10757 still has locks held!
5.13.0-rc4-build4+ #91 Not tainted
------------------------------------
1 lock held by fsstress/10757:
#0:
ffff888104eac530
(
sb_pagefaults
as filesystem freezing is modelled as a lock.
Fix this by removing all the direct returns from within the function,
and using 'ret' to indicate whether we were interrupted or successful.
Fixes:
1cf7a1518aef ("afs: Implement shared-writeable mmap")
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/20210616154900.1958373-1-willy@infradead.org/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pavel Skripkin [Fri, 18 Jun 2021 13:49:02 +0000 (16:49 +0300)]
net: ethernet: fix potential use-after-free in ec_bhf_remove
static void ec_bhf_remove(struct pci_dev *dev)
{
...
struct ec_bhf_priv *priv = netdev_priv(net_dev);
unregister_netdev(net_dev);
free_netdev(net_dev);
pci_iounmap(dev, priv->dma_io);
pci_iounmap(dev, priv->io);
...
}
priv is netdev private data, but it is used
after free_netdev(). It can cause use-after-free when accessing priv
pointer. So, fix it by moving free_netdev() after pci_iounmap()
calls.
Fixes:
6af55ff52b02 ("Driver for Beckhoff CX5020 EtherCAT master module.")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 18 Jun 2021 19:22:55 +0000 (12:22 -0700)]
Merge tag 'mac80211-for-net-2021-06-18' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A couple of straggler fixes:
* a minstrel HT sample check fix
* peer measurement could double-free on races
* certificate file generation at build time could
sometimes hang
* some parameters weren't reset between connections
in mac80211
* some extensible elements were treated as non-
extensible, possibly causuing bad connections
(or failures) if the AP adds data
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Toke Høiland-Jørgensen [Fri, 18 Jun 2021 11:04:36 +0000 (13:04 +0200)]
selftests/net: Add icmp.sh for testing ICMP dummy address responses
This adds a new icmp.sh selftest for testing that the kernel will respond
correctly with an ICMP unreachable message with the dummy (192.0.0.8)
source address when there are no IPv4 addresses configured to use as source
addresses.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toke Høiland-Jørgensen [Fri, 18 Jun 2021 11:04:35 +0000 (13:04 +0200)]
icmp: don't send out ICMP messages with a source address of 0.0.0.0
When constructing ICMP response messages, the kernel will try to pick a
suitable source address for the outgoing packet. However, if no IPv4
addresses are configured on the system at all, this will fail and we end up
producing an ICMP message with a source address of 0.0.0.0. This can happen
on a box routing IPv4 traffic via v6 nexthops, for instance.
Since 0.0.0.0 is not generally routable on the internet, there's a good
chance that such ICMP messages will never make it back to the sender of the
original packet that the ICMP message was sent in response to. This, in
turn, can create connectivity and PMTUd problems for senders. Fortunately,
RFC7600 reserves a dummy address to be used as a source for ICMP
messages (192.0.0.8/32), so let's teach the kernel to substitute that
address as a last resort if the regular source address selection procedure
fails.
Below is a quick example reproducing this issue with network namespaces:
ip netns add ns0
ip l add type veth peer netns ns0
ip l set dev veth0 up
ip a add 10.0.0.1/24 dev veth0
ip a add fc00:dead:cafe:42::1/64 dev veth0
ip r add 10.1.0.0/24 via inet6 fc00:dead:cafe:42::2
ip -n ns0 l set dev veth0 up
ip -n ns0 a add fc00:dead:cafe:42::2/64 dev veth0
ip -n ns0 r add 10.0.0.0/24 via inet6 fc00:dead:cafe:42::1
ip netns exec ns0 sysctl -w net.ipv4.icmp_ratelimit=0
ip netns exec ns0 sysctl -w net.ipv4.ip_forward=1
tcpdump -tpni veth0 -c 2 icmp &
ping -w 1 10.1.0.1 > /dev/null
tcpdump: verbose output suppressed, use -v[v]... for full protocol decode
listening on veth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes
IP 10.0.0.1 > 10.1.0.1: ICMP echo request, id 29, seq 1, length 64
IP 0.0.0.0 > 10.0.0.1: ICMP net 10.1.0.1 unreachable, length 92
2 packets captured
2 packets received by filter
0 packets dropped by kernel
With this patch the above capture changes to:
IP 10.0.0.1 > 10.1.0.1: ICMP echo request, id 31127, seq 1, length 64
IP 192.0.0.8 > 10.0.0.1: ICMP net 10.1.0.1 unreachable, length 92
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Juliusz Chroboczek <jch@irif.fr>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Esben Haabendal [Fri, 18 Jun 2021 10:52:38 +0000 (12:52 +0200)]
net: ll_temac: Avoid ndo_start_xmit returning NETDEV_TX_BUSY
As documented in Documentation/networking/driver.rst, the ndo_start_xmit
method must not return NETDEV_TX_BUSY under any normal circumstances, and
as recommended, we simply stop the tx queue in advance, when there is a
risk that the next xmit would cause a NETDEV_TX_BUSY return.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Esben Haabendal [Fri, 18 Jun 2021 10:52:33 +0000 (12:52 +0200)]
net: ll_temac: Fix TX BD buffer overwrite
Just as the initial check, we need to ensure num_frag+1 buffers available,
as that is the number of buffers we are going to use.
This fixes a buffer overflow, which might be seen during heavy network
load. Complete lockup of TEMAC was reproducible within about 10 minutes of
a particular load.
Fixes:
84823ff80f74 ("net: ll_temac: Fix race condition causing TX hang")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Esben Haabendal [Fri, 18 Jun 2021 10:52:28 +0000 (12:52 +0200)]
net: ll_temac: Add memory-barriers for TX BD access
Add a couple of memory-barriers to ensure correct ordering of read/write
access to TX BDs.
In xmit_done, we should ensure that reading the additional BD fields are
only done after STS_CTRL_APP0_CMPLT bit is set.
When xmit_done marks the BD as free by setting APP0=0, we need to ensure
that the other BD fields are reset first, so we avoid racing with the xmit
path, which writes to the same fields.
Finally, making sure to read APP0 of next BD after the current BD, ensures
that we see all available buffers.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Esben Haabendal [Fri, 18 Jun 2021 10:52:23 +0000 (12:52 +0200)]
net: ll_temac: Make sure to free skb when it is completely used
With the skb pointer piggy-backed on the TX BD, we have a simple and
efficient way to free the skb buffer when the frame has been transmitted.
But in order to avoid freeing the skb while there are still fragments from
the skb in use, we need to piggy-back on the TX BD of the skb, not the
first.
Without this, we are doing use-after-free on the DMA side, when the first
BD of a multi TX BD packet is seen as completed in xmit_done, and the
remaining BDs are still being processed.
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Fri, 18 Jun 2021 07:00:30 +0000 (09:00 +0200)]
MAINTAINERS: add Guvenc as SMC maintainer
Add Guvenc as maintainer for Shared Memory Communications (SMC)
Sockets.
Cc: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>