OSDN Git Service
Alexander Duyck [Wed, 17 Nov 2010 03:26:58 +0000 (19:26 -0800)]
ixgbe: reorder Tx cleanup so that if adapter will reset we don't rearm
The code as it existed could re-arm the queues when it was requesting a HW
reset due to a TX hang. Instead of doing that this change makes it so that
we will just exit if the hardware is believed to be hung.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 17 Nov 2010 03:26:57 +0000 (19:26 -0800)]
ixgbe: Disable RSC when ITR setting is too high to allow RSC
RSC will flush its descriptors every time the interrupt throttle timer
expires. In addition there are known issues with RSC when the rx-usecs
value is set too low. As such we are forced to clear the RSC_ENABLED bit
and reset the adapter when the rx-usecs value is set too low.
However we do not need to clear the NETIF_F_LRO flag because it is used to
indicate that the user wants to leave the LRO feature enabled, and in fact
with this change we will now re-enable RSC as soon as the rx-usecs value is
increased and the flag is still set.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 17 Nov 2010 03:26:57 +0000 (19:26 -0800)]
ixgbe: cleanup race conditions in link setup
This change makes it so that we perform link setup with interrupts
disabled. If the SFP has not been detected previously we will schedule the
SFP detection task to run in order to detect link. By doing this we avoid
the possibility of interrupts firing in the middle of our link setup during
ixgbe_up_complete.
In addition this change makes it so that the multi-speed fiber setup and SFP
setup are not mutually exclusive. The addresses issues seen in which a
link would only come up at 1G on some multi-speed fiber modules.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 17 Nov 2010 03:26:56 +0000 (19:26 -0800)]
ixgbe: add a state flags to ring
This change adds a set of state flags to the rings that allow them to
independently function allowing for features like RSC, packet split, and
TX hang detection to be done per ring instead of for the entire device.
This is accomplished by re-purposing the flow director reinit_state member
and making it a global state instead since a long for a single bit flag is
a bit wasteful.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 17 Nov 2010 03:26:55 +0000 (19:26 -0800)]
ixgbe: move CPU variable from ring into q_vector, add ring->q_vector
This is the start of work to sort out what belongs in the rings and what
belongs in the q_vector. Items like the CPU variable for make much more
sense in the q_vector since the CPU is a per-interrupt thing rather than a
per ring thing.
I also added a back-pointer from the ring to the q_vector.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 17 Nov 2010 03:26:54 +0000 (19:26 -0800)]
ixgbe: move adapter into pci_dev driver data instead of netdev
This change moves an adapter pointer into the private portion of the
pci_dev instead of a pointer to the netdev. The reason for this change is
because in most cases we just want the adapter anyway. In addition as we
start moving toward multiple netdevs per port we may want to move the
adapter pointer out of the netdevs entirely.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 17 Nov 2010 03:26:53 +0000 (19:26 -0800)]
ixgbe: remove residual code left over from earlier combining of TXDCTL
Missed some code that was left floating around in the DCB configuration
for the TXDCTL register. As a result the register was being messed with in
two different spots when we only needed to do the change once.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 17 Nov 2010 03:26:52 +0000 (19:26 -0800)]
ixgbe: move ixgbe_clear_interrupt_scheme to before pci_save_state
The main reason for this change is to keep the suspend/resume logic matched
up. The clear_interrupt_scheme function will disable MSI-X which will
effect the PCIe configuration space. Therefore we will want to do it before
we save state to avoid having the interrupt state restored by
pci_restore_state, and then trying to re-enable MSI/MSI-X interrupts via
ixgbe_setup_interrupt_scheme.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 17 Nov 2010 03:26:51 +0000 (19:26 -0800)]
ixgbe: add a netdev pointer to the ring structure
This change places a netdev pointer directly into the ring structure. This
way we can avoid having to determine which netdev we are supposed to be
using and can just access the one on the ring directly.
As a result of this change further collapse of the code is possible by
dropping the adapter from ixgbe_alloc_rx_buffers, and the netdev pointer
from ixgbe_xmit_frame_ring_adv and ixgbe_maybe_stop_tx.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 17 Nov 2010 03:26:50 +0000 (19:26 -0800)]
ixgbe: combine some stats into a union to allow for Tx/Rx stats overlap
This change moved some of the RX and TX stats into separate structures and
them placed those structures in a union in order to help reduce the size of
the ring structure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 17 Nov 2010 03:26:49 +0000 (19:26 -0800)]
ixgbe: move device pointer into the ring structure
This change is meant to simplify DMA map/unmap by providing a device
pointer. As a result the adapter pointer can be dropped from many of
the calls.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 17 Nov 2010 03:26:49 +0000 (19:26 -0800)]
ixgbe: drop ring->head, make ring->tail a pointer instead of offset
This change drops ring->head since it is not used in any hot-path and can
easily be determined using IXGBE_[RT]DH(ring->reg_idx).
It also changes ring->tail into a true pointer so we can avoid unnecessary
pointer math to find the location of the tail.
In addition I also dropped the setting of head and tail in
ixgbe_clean_[rx|tx]_ring. The only location that should be setting the head
and tail values is ixgbe_configure_[rx|tx]_ring and that is only while the
queue is disabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 17 Nov 2010 03:26:48 +0000 (19:26 -0800)]
ixgbe: cleanup ixgbe_alloc_rx_buffers
This change re-orders alloc_rx_buffers to make better use of the packet
split enabled flag. The new setup should require less branching in the
code since now we are down to fewer if statements since we either are
handling packet split or aren't.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 17 Nov 2010 03:26:47 +0000 (19:26 -0800)]
ixgbe: move GSO segments and byte count processing into ixgbe_tx_map
This change simplifies the work being done by the TX interrupt handler and
pushes it into the tx_map call. This allows for fewer cache misses since
the TX cleanup now accesses almost none of the skb members.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 17 Nov 2010 03:26:46 +0000 (19:26 -0800)]
ixgbe: remove unnecessary re-init of adapter on Rx-csum change
There is no need to reset the adapter when changing the Rx checksum
settings. Since the only change is a software flag we can disable it
without needing to reset the entire adapter.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Fastabend [Wed, 17 Nov 2010 03:26:45 +0000 (19:26 -0800)]
ixgbe: DCB: credit max only needs to be gt TSO size for 82598
The maximum credits per traffic class only needs to be greater
then the TSO size for 82598 devices. The 82599 devices do not
have this requirement so only do this test for 82598 devices.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Fastabend [Wed, 17 Nov 2010 03:26:44 +0000 (19:26 -0800)]
ixgbe: DCB set PFC high and low water marks per data sheet specs
Currently the high and low water marks for PFC are being set
conservatively for jumbo frames. This means the RX buffers
are being underutilized in the default 1500 MTU. This patch
fixes this so that the water marks are set as described in
the data sheet considering the MTU size.
The equation used is,
RTT * 1.44 + MTU * 1.44 + MTU
Where RTT is the round trip time and MTU is the max frame size
in KB. To avoid floating point arithmetic FC_HIGH_WATER is
defined
((((RTT + MTU) * 144) + 99) / 100) + MTU
This changes how the hardware field fc.low_water and
fc.high_water are used. With this change they are no longer
storing the actual low water and high water markers but are
storing the required head room in the buffer. This simplifies
the logic and we do not need to account for the size of the
buffer when setting the thresholds.
Testing with iperf and 16 threads showed a slight uptick in
throughput over a single traffic class .1-.2Gbps and a reduction
in pause frames. Without the patch a 30 second run would show
~10-15 pause frames being transmitted with the patch ~2-5 are
seen. Test were run back to back with 82599.
Note RXPBSIZE is in KB and low and high water marks fields are
also in KB. However the FCRT* registers are 32B granularity and
right shifted 5 into the register,
(((rx_pbsize - water_mark) * 1024) / 32) << 5
is the most explicit conversion here we simplify
(rx_pbsize - water_mark) * 32 << 5 = (rx_pbsize - water_mark) << 10
This patch updates the PFC thresholds and legacy FC thresholds.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Greg Rose [Wed, 17 Nov 2010 03:26:43 +0000 (19:26 -0800)]
ixgbevf: Update Version String and Copyright Notice
Update version string and copyright notice.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric Dumazet [Wed, 17 Nov 2010 03:26:42 +0000 (19:26 -0800)]
ixgbe: delay rx_ring freeing
"cat /proc/net/dev" uses RCU protection only.
Its quite possible we call a driver get_stats() method while device is
dismantling and freeing its data structures.
So get_stats() methods must be very careful not accessing driver private
data without appropriate locking.
In ixgbe case, we access rx_ring pointers. These pointers are freed in
ixgbe_clear_interrupt_scheme() and set to NULL, this can trigger NULL
dereference in ixgbe_get_stats64()
A possible fix is to use RCU locking in ixgbe_get_stats64() and defer
rx_ring freeing after a grace period in ixgbe_clear_interrupt_scheme()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Tantilov, Emil S <emil.s.tantilov@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric Dumazet [Tue, 16 Nov 2010 05:56:04 +0000 (05:56 +0000)]
net: reorder struct sock fields
Right now, fields in struct sock are not optimally ordered, because each
path (RX softirq, TX completion, RX user, TX user) has to touch fields
that are contained in many different cache lines.
The really critical thing is to shrink number of cache lines that are
used at RX softirq time : CPU handling softirqs for a device can receive
many frames per second for many sockets. If load is too big, we can drop
frames at NIC level. RPS or multiqueue cards can help, but better reduce
latency if possible.
This patch starts with UDP protocol, then additional patches will try to
reduce latencies of other ones as well.
At RX softirq time, fields of interest for UDP protocol are :
(not counting ones in inet struct for the lookup)
Read/Written:
sk_refcnt (atomic increment/decrement)
sk_rmem_alloc & sk_backlog.len (to check if there is room in queues)
sk_receive_queue
sk_backlog (if socket locked by user program)
sk_rxhash
sk_forward_alloc
sk_drops
Read only:
sk_rcvbuf (sk_rcvqueues_full())
sk_filter
sk_wq
sk_policy[0]
sk_flags
Additional notes :
- sk_backlog has one hole on 64bit arches. We can fill it to save 8
bytes.
- sk_backlog is used only if RX sofirq handler finds the socket while
locked by user.
- sk_rxhash is written only once per flow.
- sk_drops is written only if queues are full
Final layout :
[1] One section grouping all read/write fields, but placing rxhash and
sk_backlog at the end of this section.
[2] One section grouping all read fields in RX handler
(sk_filter, sk_rcv_buf, sk_wq)
[3] Section used by other paths
I'll post a patch on its own to put sk_refcnt at the end of struct
sock_common so that it shares same cache line than section [1]
New offsets on 64bit arch :
sizeof(struct sock)=0x268
offsetof(struct sock, sk_refcnt) =0x10
offsetof(struct sock, sk_lock) =0x48
offsetof(struct sock, sk_receive_queue)=0x68
offsetof(struct sock, sk_backlog)=0x80
offsetof(struct sock, sk_rmem_alloc)=0x80
offsetof(struct sock, sk_forward_alloc)=0x98
offsetof(struct sock, sk_rxhash)=0x9c
offsetof(struct sock, sk_rcvbuf)=0xa4
offsetof(struct sock, sk_drops) =0xa0
offsetof(struct sock, sk_filter)=0xa8
offsetof(struct sock, sk_wq)=0xb0
offsetof(struct sock, sk_policy)=0xd0
offsetof(struct sock, sk_flags) =0xe0
Instead of :
sizeof(struct sock)=0x270
offsetof(struct sock, sk_refcnt) =0x10
offsetof(struct sock, sk_lock) =0x50
offsetof(struct sock, sk_receive_queue)=0xc0
offsetof(struct sock, sk_backlog)=0x70
offsetof(struct sock, sk_rmem_alloc)=0xac
offsetof(struct sock, sk_forward_alloc)=0x10c
offsetof(struct sock, sk_rxhash)=0x128
offsetof(struct sock, sk_rcvbuf)=0x4c
offsetof(struct sock, sk_drops) =0x16c
offsetof(struct sock, sk_filter)=0x198
offsetof(struct sock, sk_wq)=0x88
offsetof(struct sock, sk_policy)=0x98
offsetof(struct sock, sk_flags) =0x130
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 15 Nov 2010 19:58:26 +0000 (19:58 +0000)]
udp: use atomic_inc_not_zero_hint
UDP sockets refcount is usually 2, unless an incoming frame is going to
be queued in receive or backlog queue.
Using atomic_inc_not_zero_hint() permits to reduce latency, because
processor issues less memory transactions.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 11 Nov 2010 09:42:45 +0000 (09:42 +0000)]
vlan: remove ndo_select_queue() logic
Now vlan are lockless, we dont need special ndo_select_queue() logic.
dev_pick_tx() will do the multiqueue stuff on the real device transmit.
Suggested-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 10 Nov 2010 23:42:00 +0000 (23:42 +0000)]
vlan: lockless transmit path
vlan is a stacked device, like tunnels. We should use the lockless
mechanism we are using in tunnels and loopback.
This patch completely removes locking in TX path.
tx stat counters are added into existing percpu stat structure, renamed
from vlan_rx_stats to vlan_pcpu_stats.
Note : this partially reverts commit
2e59af3dcbdf (vlan: multiqueue vlan
device)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 10 Nov 2010 21:14:04 +0000 (21:14 +0000)]
macvlan: lockless tx path
macvlan is a stacked device, like tunnels. We should use the lockless
mechanism we are using in tunnels and loopback.
This patch completely removes locking in TX path.
tx stat counters are added into existing percpu stat structure, renamed
from rx_stats to pcpu_stats.
Note : this reverts commit
2c11455321f37 (macvlan: add multiqueue
capability)
Note : rx_errors converted to a 32bit counter, like tx_dropped, since
they dont need 64bit range.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Tue, 16 Nov 2010 18:26:47 +0000 (10:26 -0800)]
packet: Enhance AF_PACKET implementation to not require high order contiguous memory allocation (v4)
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit
Version 4 of this patch.
Change notes:
1) Removed extra memset. Didn't think kcalloc added a GFP_ZERO the way kzalloc did :)
Summary:
It was shown to me recently that systems under high load were driven very deep
into swap when tcpdump was run. The reason this happened was because the
AF_PACKET protocol has a SET_RINGBUFFER socket option that allows the user space
application to specify how many entries an AF_PACKET socket will have and how
large each entry will be. It seems the default setting for tcpdump is to set
the ring buffer to 32 entries of 64 Kb each, which implies 32 order 5
allocation. Thats difficult under good circumstances, and horrid under memory
pressure.
I thought it would be good to make that a bit more usable. I was going to do a
simple conversion of the ring buffer from contigous pages to iovecs, but
unfortunately, the metadata which AF_PACKET places in these buffers can easily
span a page boundary, and given that these buffers get mapped into user space,
and the data layout doesn't easily allow for a change to padding between frames
to avoid that, a simple iovec change is just going to break user space ABI
consistency.
So I've done this, I've added a three tiered mechanism to the af_packet set_ring
socket option. It attempts to allocate memory in the following order:
1) Using __get_free_pages with GFP_NORETRY set, so as to fail quickly without
digging into swap
2) Using vmalloc
3) Using __get_free_pages with GFP_NORETRY clear, causing us to try as hard as
needed to get the memory
The effect is that we don't disturb the system as much when we're under load,
while still being able to conduct tcpdumps effectively.
Tested successfully by me.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Tue, 9 Nov 2010 14:35:16 +0000 (14:35 +0000)]
drivers/isdn/mISDN: Use printf extension %pV
Using %pV reduces the number of printk calls and
eliminates any possible message interleaving from
other printk calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt [Tue, 16 Nov 2010 17:52:32 +0000 (09:52 -0800)]
netlink: let nlmsg and nla functions take pointer-to-const args
The changed functions do not modify the NL messages and/or attributes
at all. They should use const (similar to strchr), so that callers
which have a const nlmsg/nlattr around can make use of them without
casting.
While at it, constify a data array.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Mon, 15 Nov 2010 20:29:21 +0000 (20:29 +0000)]
ipv6: fix missing in6_ifa_put in addrconf
Fix ref count bug introduced by
commit
2de795707294972f6c34bae9de713e502c431296
Author: Lorenzo Colitti <lorenzo@google.com>
Date: Wed Oct 27 18:16:49 2010 +0000
ipv6: addrconf: don't remove address state on ifdown if the address
is being kept
Fix logic so that addrconf_ifdown() decrements the inet6_ifaddr
refcnt correctly with in6_ifa_put().
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 16 Nov 2010 17:17:12 +0000 (09:17 -0800)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6
David S. Miller [Tue, 16 Nov 2010 04:15:03 +0000 (20:15 -0800)]
net: Export netif_get_vlan_features().
ERROR: "netif_get_vlan_features" [drivers/net/xen-netfront.ko] undefined!
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasanthy Kolluri [Mon, 15 Nov 2010 08:09:55 +0000 (08:09 +0000)]
enic: Fix build warnings
Fix data type of argument passed to pci_alloc_consistent and pci_free_consistent routines.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Cox [Mon, 15 Nov 2010 07:30:42 +0000 (07:30 +0000)]
hso: Fix unused variable warning
Fallout from the TIOCGICOUNT work
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 15 Nov 2010 06:38:14 +0000 (06:38 +0000)]
bridge: add RCU annotations to bridge port lookup
br_port_get() renamed to br_port_get_rtnl() to make clear RTNL is held.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Mon, 15 Nov 2010 06:38:13 +0000 (06:38 +0000)]
bridge: fix RCU races with bridge port
The macro br_port_exists() is not enough protection when only
RCU is being used. There is a tiny race where other CPU has cleared port
handler hook, but is bridge port flag might still be set.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Mon, 15 Nov 2010 06:38:12 +0000 (06:38 +0000)]
netdev: add rcu annotations to receive handler hook
Suggested by Eric's bridge RCU changes.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 15 Nov 2010 06:38:11 +0000 (06:38 +0000)]
bridge: add proper RCU annotation to should_route_hook
Add br_should_route_hook_t typedef, this is the only way we can
get a clean RCU implementation for function pointer.
Move route_hook to location where it is used.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 15 Nov 2010 06:38:10 +0000 (06:38 +0000)]
bridge: add RCU annotation to bridge multicast table
Add modern __rcu annotatations to bridge multicast table.
Use newer hlist macros to avoid direct access to hlist internals.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sun, 14 Nov 2010 17:05:00 +0000 (17:05 +0000)]
net/ipv6/mcast.c: Remove unnecessary semicolons
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sun, 14 Nov 2010 17:04:58 +0000 (17:04 +0000)]
include/net/caif/cfctrl.h: Remove unnecessary semicolons
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sun, 14 Nov 2010 17:04:57 +0000 (17:04 +0000)]
include/linux/if_macvlan.h: Remove unnecessary semicolons
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sun, 14 Nov 2010 17:04:37 +0000 (17:04 +0000)]
drivers/net/cnic.c: Remove unnecessary semicolons
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sun, 14 Nov 2010 17:04:33 +0000 (17:04 +0000)]
drivers/net/ixgbe: Remove unnecessary semicolons
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sun, 14 Nov 2010 17:04:32 +0000 (17:04 +0000)]
drivers/net/e1000e: Remove unnecessary semicolons
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sun, 14 Nov 2010 17:04:31 +0000 (17:04 +0000)]
drivers/net/bnx2x: Remove unnecessary semicolons
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sun, 14 Nov 2010 17:04:26 +0000 (17:04 +0000)]
drivers/isdn: Remove unnecessary semicolons
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 15 Nov 2010 18:59:49 +0000 (10:59 -0800)]
Merge branch 'dccp' of git://eden-feed.erg.abdn.ac.uk/net-next-2.6
Tom Herbert [Tue, 9 Nov 2010 10:47:38 +0000 (10:47 +0000)]
net: Simplify RX queue allocation
This patch move RX queue allocation to alloc_netdev_mq and freeing of
the queues to free_netdev (symmetric to TX queue allocation). Each
kobject RX queue takes a reference to the queue's device so that the
device can't be freed before all the kobjects have been released-- this
obviates the need for reference counts specific to RX queues.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Tue, 9 Nov 2010 10:47:30 +0000 (10:47 +0000)]
net: Move TX queue allocation to alloc_netdev_mq
TX queues are now allocated in alloc_netdev_mq and freed in
free_netdev.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timo Teräs [Wed, 3 Nov 2010 04:41:38 +0000 (04:41 +0000)]
xfrm: use gre key as flow upper protocol info
The GRE Key field is intended to be used for identifying an individual
traffic flow within a tunnel. It is useful to be able to have XFRM
policy selector matches to have different policies for different
GRE tunnels.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 15 Nov 2010 18:37:30 +0000 (10:37 -0800)]
vlan: Fix build warning in vlandev_seq_show()
net/8021q/vlanproc.c: In function 'vlandev_seq_show':
net/8021q/vlanproc.c:283:20: warning: unused variable 'fmt'
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Lamparter [Fri, 29 Oct 2010 21:11:23 +0000 (23:11 +0200)]
carl9170: use generic sign_extend32
This patch replaces the handcrafted
sign extension cruft with a generic
bitop function.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andreas Herrmann [Mon, 30 Aug 2010 19:04:01 +0000 (19:04 +0000)]
bitops: Provide generic sign_extend32 function
This patch moves code out from wireless drivers where two different
functions are defined in three code locations for the same purpose and
provides a common function to sign extend a 32-bit value.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Grazvydas Ignotas [Wed, 3 Nov 2010 22:13:49 +0000 (00:13 +0200)]
wl1251: use wl12xx_platform_data to pass data
Make use the newly added method to pass platform data for wl1251 too.
This allows to eliminate some redundant code.
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Grazvydas Ignotas [Mon, 8 Nov 2010 13:29:36 +0000 (15:29 +0200)]
wl1251: add runtime PM support for SDIO
Add runtime PM support, similar to how it's done for wl1271.
This allows to power down the card when the driver is loaded but
network is not in use.
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Grazvydas Ignotas [Wed, 3 Nov 2010 22:13:47 +0000 (00:13 +0200)]
wl1251: add power callback to wl1251_if_operations
Call interface specific power callback before calling board specific
one. Also allow that callback to fail. This is how it's done for
wl1271 and will be used for runtime_pm support.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Wed, 10 Nov 2010 17:56:50 +0000 (09:56 -0800)]
iwlagn: enable shadow register
For 6000 series devices and up, enable automatic update MAC's register
for better power usage in PSP mode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shanyu Zhao [Wed, 10 Nov 2010 17:56:49 +0000 (09:56 -0800)]
iwlwifi: disable disconnected antenna for advanced bt coex
Disconnected antenna algorithm is used to find out which antennas are
disconnected. It should be disabled for devices that support advanced
bluetooth coexist.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shanyu Zhao [Wed, 10 Nov 2010 17:56:48 +0000 (09:56 -0800)]
iwlwifi: seperate disconnected antenna function
Disconnected antenna algorithm is seperated into its own function from chain noise
calibration routine for better code management.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 10 Nov 2010 17:56:47 +0000 (09:56 -0800)]
iwlagn: fix RXON HT
When the HT information is changed due to
BSS changes (like legacy stations joining)
we need to recalculate HT RXON parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 10 Nov 2010 17:56:46 +0000 (09:56 -0800)]
iwlagn: re-enable calibration
During the RXON rewrite, this code got lost.
When we've just associated, we need to enable
all calibrations and see if some were already
finished. Add back the missing code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 10 Nov 2010 17:56:45 +0000 (09:56 -0800)]
iwlagn: fix RXON issues
The RXON rework resulted in a massive loss of
throughput because we weren't programming the
device completely correctly -- the BSSID has
to be programmed into the device before the
AP station is uploaded. To fix this, simply
always send the unassoc RXON, i.e. even when
it was already unassoc so that the BSSID and
some other parameters are updated properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 10 Nov 2010 17:56:44 +0000 (09:56 -0800)]
iwlagn: fix needed chains calculation
Garen noticed that this was wrong. Fix
the calibration -- default to multiple
chains and fall back to single where
possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Wed, 10 Nov 2010 17:56:43 +0000 (09:56 -0800)]
iwlwifi: resending QoS command when HT changes
"mac80211: Fix WMM driver queue configuration"
inadvertedly broke iwlwifi, because now mac80211
configures the QoS settings before assoc, and
therefore before HT. Thus, iwlwifi no longer told
the device about the HT setting, which it needs
to -- and thus throughput went down a lot. Fix
this by resending the QoS command to the device
not only when QoS/WMM settings change, but also
when HT changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Winkler, Tomas [Wed, 10 Nov 2010 17:56:42 +0000 (09:56 -0800)]
iwlwlifi: update rx write pointer w/o request mac access in the CAM mode
In iwl_rx_queue_update_write_ptr function
replace iwl_write_direct32 with iwl_write32 when not in power save mode.
We don't have to go through grab nic access as the NIC is already awake.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Wed, 10 Nov 2010 17:56:41 +0000 (09:56 -0800)]
iwlwifi: legacy tx_cmd_protection function
Legacy (4965 and 3945) devices has different tx_cmd_protection routine.
Move to iwl-legacy.c
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Wed, 10 Nov 2010 17:56:40 +0000 (09:56 -0800)]
iwlwifi: put all the isr related function under ops
There were two type of isr supported by iwlwifi devices.
legacy isr - only used by legacy devices (3945 & 4965)
ict isr - used by all new generation of iwlwifi devices
Move all the isr related functions into ops, the ict type of isr
supports only needed for newer devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Wed, 10 Nov 2010 17:56:39 +0000 (09:56 -0800)]
iwlwifi: Legacy isr only used by legacy devices
Move iwl_isr_legacy function to iwl_legacy.c since it only used
by legacy devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 10 Nov 2010 17:56:38 +0000 (09:56 -0800)]
iwlagn: fix non-5000+ build
When building 4965 without 5000+ there were a
lot of build errors due to functions being used
that weren't even compiled in. To fix this move
some code around and only compile the HCMD code
for 5000+ series as it's not used for 4965.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Wed, 10 Nov 2010 17:56:37 +0000 (09:56 -0800)]
iwlagn: update PCI ID for 100 series devices
Update the supported PCI ID list for 100 series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Wed, 10 Nov 2010 17:56:36 +0000 (09:56 -0800)]
iwlagn: update PCI ID for 6000g2a series devices
Update the supported PCI ID list for 6000g2a series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Wed, 10 Nov 2010 17:56:35 +0000 (09:56 -0800)]
iwlagn: update PCI ID for 6000g2b series devices
Update the supported PCI ID list for 6000g2b series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Mon, 8 Nov 2010 18:50:03 +0000 (10:50 -0800)]
ath5k: Print stats as unsigned ints.
The debugfs code for ath5k was printing some unsigned int
stats with %d instead of %u. This meant that you could see
negative numbers instead of a clean wrap.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 6 Nov 2010 14:49:01 +0000 (15:49 +0100)]
rt2x00: Add watchdog functions for HW queue
Add watchdog functions for managing the Queues inside the hardware.
Normally the driver doesn't have much to do with these queues
directly, but the Ralink drivers did implement watchdog functions
for these. These watchdog functions are not triggered that often,
compared to the other watchdog functions, but I have at least
seen them trigger once or twice during a long stresstest run.
v2: Add extra documentation for register fields
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 6 Nov 2010 14:48:43 +0000 (15:48 +0100)]
rt2x00: Remove rt2x00lib_toggle_rx
As part of the queue refactoring, the rt2x00lib_toggle_rx
can be removed and replaced with the call directly to
the set_device_state callback function.
We can remove the STATE_RADIO_RX_ON_LINK and
STATE_RADIO_RX_OFF_LINK, as it was only used for
special behavior inside rt2x00lib rather then the
drivers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 6 Nov 2010 14:48:23 +0000 (15:48 +0100)]
rt2x00: Fix rt2x00queue_kick_tx_queue arguments
The queue_entry argument to rt2x00queue_kick_tx_queue,
doesn't make sense due to the function name (it is called
kick QUEUE)... But neither do we need the queue_entry, since
we need the data_queue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 6 Nov 2010 14:48:05 +0000 (15:48 +0100)]
rt2x00: Rename queue->lock to queue->index_lock
The queue->lock is only used to protect the index
numbers. Rename the lock accordingly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Einon [Sat, 6 Nov 2010 14:47:46 +0000 (15:47 +0100)]
rt2x00: checkpatch.pl error fixes for rt73usb.c
rt73usb.c:43: ERROR: do not initialise statics to 0 or NULL
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Einon [Sat, 6 Nov 2010 14:47:25 +0000 (15:47 +0100)]
rt2x00: checkpatch.pl error fixes for rt2x00queue.c
rt2x00queue.c:804: ERROR: space prohibited after that open parenthesis '('
rt2x00queue.c:805: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Einon [Sat, 6 Nov 2010 14:47:09 +0000 (15:47 +0100)]
rt2x00: checkpatch.pl error fixes for rt2x00link.c
rt2x00link.c:70: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Einon [Sat, 6 Nov 2010 14:46:53 +0000 (15:46 +0100)]
rt2x00: checkpatch.pl error fixes for rt2x00lib.h
rt2x00lib.h:60: ERROR: space prohibited after that open parenthesis '('
rt2x00lib.h:60: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Einon [Sat, 6 Nov 2010 14:46:36 +0000 (15:46 +0100)]
rt2x00: checkpatch.pl error fixes for rt2x00dev.c
rt2x00dev.c:689: ERROR: spaces required around that '=' (ctx:WxV)
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Einon [Sat, 6 Nov 2010 14:46:17 +0000 (15:46 +0100)]
rt2x00: checkpatch.pl error fixes for rt2x00config.c
rt2x00config.c:136: ERROR: space required before the open parenthesis '('
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Einon [Sat, 6 Nov 2010 14:45:58 +0000 (15:45 +0100)]
rt2x00: checkpatch.pl error fixes for rt2800usb.h
rt2800usb.h:43: ERROR: space prohibited after that open parenthesis '('
rt2800usb.h:43: ERROR: space prohibited before that close parenthesis ')'
rt2800usb.h:44: ERROR: space prohibited after that open parenthesis '('
rt2800usb.h:44: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Einon [Sat, 6 Nov 2010 14:45:41 +0000 (15:45 +0100)]
rt2x00: checkpatch.pl error fixes for rt2800usb.c
rt2800usb.c:48: ERROR: do not initialise statics to 0 or NULL
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Einon [Sat, 6 Nov 2010 14:45:22 +0000 (15:45 +0100)]
rt2x00: checkpatch.pl error fixes for rt2800pci.h
rt2800pci.h:41: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:42: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:43: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:44: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:55: ERROR: space prohibited after that open parenthesis '('
rt2800pci.h:55: ERROR: space prohibited before that close parenthesis ')'
rt2800pci.h:56: ERROR: space prohibited after that open parenthesis '('
rt2800pci.h:56: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Einon [Sat, 6 Nov 2010 14:45:06 +0000 (15:45 +0100)]
rt2x00: checkpatch.pl error fixes for rt2800lib.c
rt2800lib.c:831: ERROR: inline keyword should sit between storage class and type
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Einon [Sat, 6 Nov 2010 14:44:52 +0000 (15:44 +0100)]
rt2x00: checkpatch.pl error fixes for rt2800.h
rt2800.h:1511: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1511: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1513: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1513: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1515: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1515: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1517: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1517: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1519: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1519: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1521: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1521: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1661: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1661: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1662: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1662: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1663: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:2013: ERROR: space prohibited after that open parenthesis '('
rt2800.h:2013: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:2014: ERROR: space prohibited after that open parenthesis '('
rt2800.h:2014: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Einon [Sat, 6 Nov 2010 14:44:33 +0000 (15:44 +0100)]
rt2x00: checkpatch.pl error fixes for rt2500usb.c
rt2500usb.c:42: ERROR: do not initialise statics to 0 or NULL
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Einon [Sat, 6 Nov 2010 14:44:15 +0000 (15:44 +0100)]
rt2x00: checkpatch.pl error fixes for rt2500pci.h
rt2500pci.h:1091: ERROR: space prohibited after that open parenthesis '('
rt2500pci.h:1091: ERROR: space prohibited before that close parenthesis ')'
rt2500pci.h:1092: ERROR: space prohibited after that open parenthesis '('
rt2500pci.h:1092: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Einon [Sat, 6 Nov 2010 14:44:00 +0000 (15:44 +0100)]
rt2x00: checkpatch.pl error fixes for rt2400pci.h
rt2400pci.h:812: ERROR: space prohibited after that open parenthesis '('
rt2400pci.h:812: ERROR: space prohibited before that close parenthesis ')'
rt2400pci.h:813: ERROR: space prohibited after that open parenthesis '('
rt2400pci.h:813: ERROR: space prohibited before that close parenthesis ')'
rt2400pci.h:950: ERROR: Macros with complex values should be enclosed in parenthesis
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Sat, 6 Nov 2010 13:07:10 +0000 (14:07 +0100)]
carl9170: tx path review
This patch fixes a few shortcomings in the tx path.
* move temp. ampdu_[ack]_len out of txinfo->pad.
* fix WARN_ON from tx.c:line 300 when tx_ampdu_queue
fails to queue the frame.
* In tx_prepare, we already have a local pointer
to the station's ieee80211_sta struct.
* remove a second !sta check, tx_prepare already takes
care of that.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jesper Juhl [Thu, 4 Nov 2010 21:59:56 +0000 (22:59 +0100)]
mac80211: Remove redundant checks for NULL before calls to crypto_free_cipher()
crypto_free_cipher() is a wrapper around crypto_free_tfm() which is a
wrapper around crypto_destroy_tfm() and the latter can handle being passed
a NULL pointer, so checking for NULL in the
ieee80211_aes_key_free()/ieee80211_aes_cmac_key_free() wrappers around
crypto_free_cipher() is pointless and just increase object code size
needlesly and makes us execute extra test/branch instructions that we
don't need.
Btw; don't we have to many wrappers around wrappers ad nauseam here?
Anyway, this patch removes the redundant conditionals.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lalith Suresh [Thu, 4 Nov 2010 19:43:16 +0000 (20:43 +0100)]
rt2x00: Fix comments in rt73usb.h and rt61pci.h
This patch fixes a few comments in rt73usb.h and rt61pci.h.
Signed-off-by: Lalith Suresh <suresh.lalith@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 4 Nov 2010 19:42:36 +0000 (20:42 +0100)]
rt2x00: Fix hw crypto in AP mode for some devices
The BSSID register shouldn't be set in AP mode on some older devices (like
rt73usb) as it breaks hw crypto on these. However, rt2800 devices explicitly
need the BSSID register set to the same value as our own MAC address (only
in AP mode).
Hence, don't set the BSSID from rt2x00lib but move it down into rt2800 to
avoid problems on older devices.
This fixes a regression (at least for rt73usb) and avoids a new regression
for rt2800 devices in 2.6.36.
Reported-by: Johannes Stezenbach <js@sig21.net>
Reported-by: Lee <lee-in-berlin@web.de>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Thu, 4 Nov 2010 19:41:05 +0000 (20:41 +0100)]
rt2x00: Fix crash on USB unplug
By not scheduling the TX/RX completion worker threads
when Radio is disabled, or hardware has been unplugged,
the queues cannot be completely cleaned.
This causes crashes when the hardware has been unplugged while
the radio is still enabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Thu, 4 Nov 2010 19:40:46 +0000 (20:40 +0100)]
rt2x00: Fix MCU_SLEEP arguments
Legacy driver uses 0xff as the second argument for the MCU_SLEEP
command. It is still unknown what the values actually mean, but
this will at least keep the command in-sync with the original
driver.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Thu, 4 Nov 2010 19:40:11 +0000 (20:40 +0100)]
rt2x00: Implement flush callback
Implement a basic flush callback function, which simply loops
over all TX queues and waits until all frames have been transmitted
and the status reports have been gathered.
At this moment we don't support dropping any frames during the
flush, but mac80211 will only send 'false' for this argument anyway,
so this is not important at this time.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Thu, 4 Nov 2010 19:39:48 +0000 (20:39 +0100)]
rt2x00: Remove failsave from rt2x00usb_watchdog_tx_dma
When the TX status handler failed to clear the queue
in rt2x00usb_watchdog_tx_dma() we shouldn't use a failsave
to use the rt2x00usb txdone handler.
If a driver has overriden the txdone handler it must make
sure the txdone handler is capable of cleaning up the queue itself.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Thu, 4 Nov 2010 19:39:23 +0000 (20:39 +0100)]
rt2x00: Rename rt2x00queue_timeout
Rename rt2x00queue_timeout to rt2x00queue_status_timeout to
better describe what is actually timing out (note that
we already have a rt2x00queue_dma_timeout).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 4 Nov 2010 19:38:56 +0000 (20:38 +0100)]
rt2x00: Optimize rt2x00debug_dump_frame when frame dumping is not active
When rt2x00 is compiled with debugging but frame dumping is currently
not active we can avoid the call to do_gettimeofday. Furthermore,
frame dumping is not the default case, mark it as unlikely.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>