OSDN Git Service
Jingoo Han [Tue, 30 Jul 2013 08:05:28 +0000 (17:05 +0900)]
usb: misc: usb3503: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jingoo Han [Tue, 30 Jul 2013 08:06:20 +0000 (17:06 +0900)]
usb: renesas: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jingoo Han [Tue, 30 Jul 2013 08:25:19 +0000 (17:25 +0900)]
USB: c67x00: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joe Perches [Tue, 30 Jul 2013 15:17:59 +0000 (08:17 -0700)]
MAINTAINERS: USB, remove F: drivers/net/usb/ pattern
On Tue, 2013-07-30 at 06:58 -0700, Greg KH wrote:
> In the future, you do not need to send drivers/net/usb/ patches to me,
> netdev and the linux-usb mailing lists should be sufficient.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Julius Werner [Wed, 31 Jul 2013 02:51:20 +0000 (19:51 -0700)]
usb: core: don't try to reset_device() a port that got just disconnected
The USB hub driver's event handler contains a check to catch SuperSpeed
devices that transitioned into the SS.Inactive state and tries to fix
them with a reset. It decides whether to do a plain hub port reset or
call the usb_reset_device() function based on whether there was a device
attached to the port.
However, there are device/hub combinations (found with a JetFlash
Transcend mass storage stick (8564:1000) on the root hub of an Intel
LynxPoint PCH) which can transition to the SS.Inactive state on
disconnect (and stay there long enough for the host to notice). In this
case, above-mentioned reset check will call usb_reset_device() on the
stale device data structure. The kernel will send pointless LPM control
messages to the no longer connected device address and can even cause
several 5 second khubd stalls on some (buggy?) host controllers, before
finally accepting the device's fate amongst a flurry of error messages.
This patch makes the choice of reset dependent on the port status that
has just been read from the hub in addition to the existence of an
in-kernel data structure for the device, and only proceeds with the more
extensive reset if both are valid.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Feng-Hsin Chiang [Mon, 29 Jul 2013 16:48:32 +0000 (16:48 +0000)]
usb: host: Faraday fotg210-hcd driver
FOTG210 is an OTG controller which can be configured as an
USB2.0 host. FOTG210 host is an ehci-like controller with
some differences. First, register layout of FOTG210 is
incompatible with EHCI. Furthermore, FOTG210 is lack of
siTDs which means iTDs are used for both HS and FS ISO
transfer.
Signed-off-by: Feng-Hsin Chiang <john453@faraday-tech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Frank Schäfer [Mon, 29 Jul 2013 16:33:22 +0000 (18:33 +0200)]
USB: serial: pl2303: fix the upper baud rate limit check for type_0/1 chips
Fixes the following regression that has been introduced recently with
commit
b2d6d98fc7:
With type_0 and type_1 chips
- all baud rates <
1228800 baud are rounded up to
1228800 baud
- the device silently runs at 9600 baud for all baud rates >
1228800
baud
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Mon, 29 Jul 2013 14:43:16 +0000 (07:43 -0700)]
Merge 3.11-rc3 into usb-next
Linus Torvalds [Mon, 29 Jul 2013 03:53:33 +0000 (20:53 -0700)]
Linux 3.11-rc3
Linus Torvalds [Mon, 29 Jul 2013 01:19:27 +0000 (18:19 -0700)]
Merge tag 'pinctrl-for-v3.11-2' of git://git./linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Driver fixes for AM33xx, SIRF and PFC pin controllers
- Fix a compile warning from the pinctrl single-register driver
- Fix a little nasty memory leak
* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: fix a memleak when freeing maps
pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
pinctrl: sirf: fix the pin number and mux bit for usp0
pinctrl: am33xx dt binding: correct include path
Linus Torvalds [Mon, 29 Jul 2013 01:10:39 +0000 (18:10 -0700)]
Merge tag 'trace-fixes-3.11-rc2' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Oleg is working on fixing a very tight race between opening a event
file and deleting that event at the same time (both must be done as
root).
I also found a bug while testing Oleg's patches which has to do with a
race with kprobes using the function tracer.
There's also a deadlock fix that was introduced with the previous
fixes"
* tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Remove locking trace_types_lock from tracing_reset_all_online_cpus()
ftrace: Add check for NULL regs if ops has SAVE_REGS set
tracing: Kill trace_cpu struct/members
tracing: Change tracing_fops/snapshot_fops to rely on tracing_get_cpu()
tracing: Change tracing_entries_fops to rely on tracing_get_cpu()
tracing: Change tracing_stats_fops to rely on tracing_get_cpu()
tracing: Change tracing_buffers_fops to rely on tracing_get_cpu()
tracing: Change tracing_pipe_fops() to rely on tracing_get_cpu()
tracing: Introduce trace_create_cpu_file() and tracing_get_cpu()
Linus Torvalds [Mon, 29 Jul 2013 01:09:34 +0000 (18:09 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is five bug fixes, two of which fix long standing problems
causing crashes (sd and mvsas). The remaining three are hung (isci
race) or lost (qla2xxx, isci) devices"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] isci: fix breakage caused by >16byte CDB patch
[SCSI] mvsas: Fix kernel panic on tile due to unaligned data access
[SCSI] sd: fix crash when UA received on DIF enabled device
[SCSI] qla2xxx: Properly set the tagging for commands.
[SCSI] isci: Fix a race condition in the SSP task management path
Linus Torvalds [Fri, 26 Jul 2013 21:40:10 +0000 (14:40 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This is just a regular fixes pull apart from the qxl one, it has
radeon and intel bits in it,
The intel fixes are for a regression with the RC6 fix and a 3.10 hdmi
regression, whereas radeon is more DPM fixes, a few lockup fixes and
some rn50/r100 DAC fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/dpm: fix r600_enable_sclk_control()
drm/radeon/dpm: implement force performance levels for rv6xx
drm/radeon/dpm: fix displaygap programming on rv6xx
drm/radeon/dpm: fix a typo in the rv6xx mclk setup
drm/i915: initialize gt_lock early with other spin locks
drm/i915: fix hdmi portclock limits
drm/radeon: fix combios tables on older cards
drm/radeon: improve dac adjust heuristics for legacy pdac
drm/radeon: Another card with wrong primary dac adj
drm/radeon: fix endian issues with DP handling (v3)
drm/radeon/vm: only align the pt base to 32k
drm/radeon: wait for 3D idle before using CP DMA
Linus Torvalds [Fri, 26 Jul 2013 21:38:50 +0000 (14:38 -0700)]
Merge branch 'qxl-fixes' of git://people.freedesktop.org/~airlied/linux
Pull qxl drm fixes from Dave Airlie:
"Okay as I warned, the qxl driver was running a bit free and loose with
its ttm object reservations and the new lockdep enabled reservation
tracking shone a bright light into it, it also with the new
reservations mutexes hits a possible deadlock during boot.
The first patch is a real fix to render the console correctly as the
driver used to just drop irq renderering as too hard, this also fixes
a sleeping while atomic warning.
The other two patches are the big ugly ones that redo how the driver
allocates objects and reserves them and makes things all work
properly, I've tested this in a VM, and compared to the current code
which hits a lockdep warning and the sleep while atomic warning before
failing.
So sorry this is coming in late, I should have tested qxl before
merging the mutex code, but I'd rather just fix qxl with this than
revert the reservations code at this point"
* 'qxl-fixes' of git://people.freedesktop.org/~airlied/linux:
qxl: convert qxl driver to proper use for reservations
qxl: allow creation of pre-pinned objects and use for releases.
drm/qxl: add delayed fb operations
Linus Torvalds [Fri, 26 Jul 2013 21:37:18 +0000 (14:37 -0700)]
Merge tag 'pm+acpi-3.11-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are just two fixes, a revert of the would-be backlight fix that
didn't work and an intel_pstate fix for two problems related to
maximum P-state selection.
Specifics:
- Revert of the ACPI video commit that I hoped would help fix
backlight problems related to Windows 8 compatibility on some
systems. Unfortunately, it turned out to cause problems to happen
too.
- Fix for two problems in intel_pstate, a possible failure to respond
to a load change on a quiet system and a possible failure to select
the highest available P-state on some systems. From Dirk
Brandewie"
* tag 'pm+acpi-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / video / i915: No ACPI backlight if firmware expects Windows 8"
cpufreq / intel_pstate: Change to scale off of max P-state
caizhiyong [Fri, 26 Jul 2013 07:12:14 +0000 (07:12 +0000)]
USB: ohci_usb warn "irq nobody cared" on shutdown
When ohci-hcd is shutting down, call ohci_usb_reset reset ohci-hcd, the
root hub generate an interrupt, but ohci->rh_state is OHCI_RH_HALTED,
and ohci_irq ignore the interrupt, the kernel trigger warning "irq
nobody cared". ehci-hcd is first disable interrupts, then reset ehci.
This patch disable ohci interrupt before reset ohci.
The patch is tested at the arm cortex-a9 demo board.
Signed-off-by: caizhiyong <caizhiyong@huawei.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Gortmaker [Thu, 4 Jul 2013 05:39:10 +0000 (01:39 -0400)]
usb: limit OMAP related USB options to OMAP2PLUS platforms
commit
57f6ce072e35770a63be0c5d5e82f90d8da7d665 ("usb: phy:
add a new driver for usb3 phy") added the new Kconfig option
OMAP_USB3, but it had no dependencies whatsoever, and hence
became available across all arch/platforms.
Which presumably caused this to show up in x86 randconfig:
warning: (USB_MUSB_HDRC && OMAP_USB3) selects \
OMAP_CONTROL_USB which has unmet direct \
dependencies (USB_SUPPORT && ARCH_OMAP2PLUS)
Then commit
6992819feb39cb9adac72170555d957d07f869f2 ("usb: phy:
fix Kconfig warning") was added. However, this just deleted the
ARCH_OMAP2PLUS dependency from OMAP_CONTROL_USB, further
compounding the problem by opening up OMAP_CONTROL_USB to
all arch/platforms as well.
Earlier it was suggested[1] that we revert the change of
6992819feb
to restore the dependency, and add a same ARCH_OMAP2PLUS dependency
to the new OMAP_USB3 entry. However that was discouraged on the
grounds of people wanting the extra sanity compile testing on x86,
even though the driver could probably never be used there.
Now we have CONFIG_COMPILE_TEST, so developers who value the ability
to compile drivers on an architecture that it never can be used for
can have that, and people who want dependencies to shield them from
seeing options that aren't relevant to their platform get what they
want too.
Here we restore the dependency but couple it with COMPILE_TEST, in
order to achieve both of the above goals.
[1] https://patchwork.kernel.org/patch/
2194511/
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Moiz Sonasath <m-sonasath@ti.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
H Hartley Sweeten [Mon, 1 Jul 2013 22:53:02 +0000 (15:53 -0700)]
usb: ohci-ep93xx: tidy up driver (*probe) and (*remove)
Merge the usb_hcd_ep93xx_probe() into ohci_hcd_ep93xx_drv_probe() and
the usb_hcd_ep93xx_remove() into ohci_hcd_ep93xx_drv_remove(). As Alan
Stern pointed out, there is no reason for them to be separate.
Also, as Alan Stern suggested, eliminate the ep93xx_start_hc() and
ep93xx_stop_hc() routines and simply call clk_enable() and clk_disable()
directly. The extra level of redirection does not add any clarity.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
H Hartley Sweeten [Mon, 1 Jul 2013 22:52:59 +0000 (15:52 -0700)]
usb: ohci-ep93xx: use devm_clk_get()
Use devm_clk_get() to make the code a bit cleaner and simpler.
This also fixes a bug where a clk_put() is not done if usb_add_hcd()
fails.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
H Hartley Sweeten [Mon, 1 Jul 2013 22:52:51 +0000 (15:52 -0700)]
usb: ohci-ep93xx: use platform_get_irq()
Use platform_get_irq() instead of accessing the platform_device
resources directly.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
H Hartley Sweeten [Mon, 1 Jul 2013 22:52:42 +0000 (15:52 -0700)]
usb: ohci-ep93xx: use devm_ioremap_resource()
Use devm_ioremap_resource() to make the code a bit cleaner and
simpler.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Fri, 26 Jul 2013 19:43:59 +0000 (12:43 -0700)]
Merge tag 'arm64-stable' of git://git./linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fixes from Catalin Marinas:
- Stack size increased to 16K (similar to other 64-bit architectures)
- Additional cache flushing for secondary CPUs boot mode
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Change kernel stack size to 16K
arm64: Fix definition of arm_pm_restart to match the declaration
arm64: virt: ensure visibility of __boot_cpu_mode
Linus Torvalds [Fri, 26 Jul 2013 19:42:40 +0000 (12:42 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is a largeish batch of fixes, mostly because I missed -rc2 due to
travel/vacation. So in number these are a bit more than ideal unless
you amortize them over two -rcs.
Quick breakdown:
- Defconfig updates
- Making multi_v7_defconfig useful on more hardware to encourage
single-image usage
- Davinci and nomadik updates due to new code merged this merge
window
- Fixes for UART on Samsung platforms, both PM and clock-related
- A handful of warning fixes from defconfig builds, including for
max8925 backlight and pxamci (both with appropriate acks)
- Exynos5440 fixes for LPAE configuration, PM
- ...plus a bunch of other smaller changes all over the place
I expect to switch to regressions-or-severe-bugs-only fixes from here
on out"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
mfd: max8925: fix dt code for backlight
ARM: omap5: Only select errata 798181 if SMP
ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
ARM: EXYNOS: Fix low level debug support
ARM: SAMSUNG: Save/restore only selected uart's registers
ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
ARM: multi_v7_defconfig: Select USB chipidea driver
ARM: pxa: propagate errors from regulator_enable() to pxamci
ARM: zynq: fix compilation warning
ARM: keystone: fix compilation warning
ARM: highbank: Only touch common coherency control register fields
ARM: footbridge: fix overlapping PCI mappings
dmaengine: shdma: fix a build failure on platforms with no DMA support
ARM: STi: Set correct ARM ERRATAs.
ARM: dts: STi: Fix pinconf setup for STiH416 serial2
ARM: nomadik: configure for NO_HZ and HRTIMERS
ARM: nomadik: update defconfig base
ARM: nomadik: Update MMC defconfigs
ARM: davinci: defconfig: enable EDMA driver
...
Linus Torvalds [Fri, 26 Jul 2013 18:38:13 +0000 (11:38 -0700)]
Merge tag 'usb-3.11-rc3' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 3.11-rc3.
Lots of little things, nothing major. A number of new device ids,
build fixes for DMA, and a bunch of other minor things. All of these
have been in the linux-next tree"
* tag 'usb-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (40 commits)
usb: Clear both buffers when clearing a control transfer TT buffer.
usb/gadget: free opts struct on error recovery
USB: mos7840: fix memory leak in open
usb: serial: option.c: remove ONDA MT825UP product ID fromdriver
usb: serial: option: add Olivetti Olicard 200
usb: serial: option: blacklist ONDA MT689DC QMI interface
xhci: fix null pointer dereference on ring_doorbell_for_active_rings
usb: host: xhci: Enable XHCI_SPURIOUS_SUCCESS for all controllers with xhci 1.0
usb: fix build warning in pci-quirks.h when CONFIG_PCI is not enabled
usb: xhci: Mark two functions __maybe_unused
xhci: Avoid NULL pointer deref when host dies.
usb: serial: option: Add ONYX 3G device support
USB: ti_usb_3410_5052: fix dynamic-id matching
usb: option: add TP-LINK MA260
USB: option: add D-Link DWM-152/C1 and DWM-156/C1
USB: EHCI: Fix resume signalling on remote wakeup
USB: cp210x: add MMB and PI ZigBee USB Device Support
usb: cp210x support SEL C662 Vendor/Device
USB: option: append Petatel NP10T device to GSM modems list
USB: misc: Add Manhattan Hi-Speed USB DVI Converter to sisusbvga
...
Linus Torvalds [Fri, 26 Jul 2013 18:37:41 +0000 (11:37 -0700)]
Merge tag 'tty-3.11-rc3' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are 3 fixes for TTY and serial issues that have been reported.
Nothing huge, but nice to get fixed"
* tag 'tty-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: tegra: correct help message in Kconfig from 'ttyHS' to 'ttyTHS'
tty/8250_early: Don't truncate last character of options
TTY: snyclinkmp: calculating wrong addresses
Linus Torvalds [Fri, 26 Jul 2013 18:36:51 +0000 (11:36 -0700)]
Merge tag 'staging-3.11-rc3' of git://git./linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some tiny drivers/staging/ fixes for 3.11-rc3
A number of bugfixes, all pretty tiny, but resolve issues that have
been reported (the kstrtos32 change fixes a data corruption problem
that Dan found). And a MAINTAINERS file update for the comedi
drivers"
* tag 'staging-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
MAINTAINERS: Update the list of maintainers for staging/comedi driver.
staging: tidspbridge: replace strict_strtol() with kstrtos32()
staging: android: logger: Correct write offset reset on error
staging: zram: protect zram_reset_device() call
staging: gdm72xx: potential use after free in send_qos_list()
staging: drm/imx: drop "select OF_VIDEOMODE"
staging: frontier: use after free in disconnect()
staging: comedi: fix a race between do_cmd_ioctl() and read/write
staging: comedi: COMEDI_CANCEL ioctl should wake up read/write
Linus Torvalds [Fri, 26 Jul 2013 18:36:12 +0000 (11:36 -0700)]
Merge tag 'char-misc-3.11-rc3' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc patches from Greg KH:
"Here are some char/misc patches for 3.11-rc3. It's pretty much just:
- mei fixes
- hyperv fixes
- new ja_JP translation update
all tiny stuff, but fixes for issues people have reported."
* tag 'char-misc-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
HOWTO ja_JP sync
mei: me: fix waiting for hw ready
mei: don't have to clean the state on power up
mei: me: fix reset state machine
mei: hbm: fix typo in error message
Tools: hv: KVP: Fix a bug in IPV6 subnet enumeration
Drivers: hv: balloon: Do not post pressure status if interrupted
Drivers: hv: balloon: Fix a bug in the hot-add code
Drivers: hv: vmbus: incorrect device name is printed when child device is unregistered
Linus Torvalds [Fri, 26 Jul 2013 18:25:25 +0000 (11:25 -0700)]
Merge tag 'sound-3.11' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a handful of regression and small fixes in ASoC, HD-audio and
USB-audio drivers.
- Sigmetal HD-audio codec regression fixes
- A copule of XRUN indication fixes for usb-audio devices
- ASoC: ep93xx build fix, sgtl5000 fix for probe order changes,
max98088 register access fix, etc"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hiface: return correct XRUN indication
ASoC: tegra: correct playback_dma_data setup
ASoC: core: double free in snd_soc_add_platform()
ALSA: usb-audio: 6fire: return correct XRUN indication
ASoC: ep93xx: fix build of ep93xx-ac97.c
ALSA: hda - Remove NO_PRESENCE bit override for Dell 1420n Laptop
ALSA: hda - Fix EAPD GPIO control for Sigmatel codecs
ASoC: atmel-ssc: remove clk_disable_unprepare call from critical section
ASoC: sgtl5000: defer the probe if clock is not found
ASoC: max98088 - fix element type of the register cache.
Linus Torvalds [Fri, 26 Jul 2013 18:22:54 +0000 (11:22 -0700)]
Merge tag 'for-linus-v3.11-rc3' of git://oss.sgi.com/xfs/xfs
Pull xfs fix from Ben Myers:
"Fix for regression in commit
cca9f93a52d2 ("xfs: don't do IO when
creating an new inode"), recovery causing filesystem corruption after
a crash"
* tag 'for-linus-v3.11-rc3' of git://oss.sgi.com/xfs/xfs:
xfs: di_flushiter considered harmful
Linus Torvalds [Fri, 26 Jul 2013 18:21:43 +0000 (11:21 -0700)]
Merge branch 'for-3.11' of git://linux-nfs.org/~bfields/linux
Pull nfsd fix from Bruce Fields:
"One more nfsd bugfix for 3.11"
* 'for-3.11' of git://linux-nfs.org/~bfields/linux:
nfsd: nfsd_open: when dentry_open returns an error do not propagate as struct file
Linus Torvalds [Fri, 26 Jul 2013 18:20:10 +0000 (11:20 -0700)]
Merge tag 'md/3.11-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Two more bugfixes for md in 3.11
Both marked for -stable, both since 3.3. I guess I should spend more
time testing..."
* tag 'md/3.11-fixes' of git://neil.brown.name/md:
md/raid5: fix interaction of 'replace' and 'recovery'.
md/raid10: remove use-after-free bug.
Linus Torvalds [Fri, 26 Jul 2013 18:17:46 +0000 (11:17 -0700)]
Merge branch 'for-3.11-fixes' of git://git./linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Assorted libata updates.
The most critical one is a fix for ahci oops during boot. Also, a new
smallish platform ahci driver is added and sata_inic162x is marked
clearly as experimental (it whines during boot too) as data corruption
seems rather common on the device and it's unlikely to get any love in
the foreseeable future. If the whining doesn't draw any attention, I
think we'd probably be better of making the driver depend on BROKEN in
a couple releases"
This is v2 of this pull request with fixed dependencies for ahci_imx.
* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci_imx: depend on CONFIG_MFD_SYSCON
ahci_imx: add ahci sata support on imx platforms
ARM: imx6q: update the sata bits definitions of gpr13
ahci: fix Null pointer dereference in achi_host_active()
libata: make it clear that sata_inic162x is experimental
libata: replace strict_strtol() with kstrtol()
ata: Fix DVD not dectected at some platform with Wellsburg PCH
Rafael J. Wysocki [Thu, 25 Jul 2013 19:43:39 +0000 (21:43 +0200)]
Revert "ACPI / video / i915: No ACPI backlight if firmware expects Windows 8"
We attempted to address a regression introduced by commit
a57f7f9
(ACPICA: Add Windows8/Server2012 string for _OSI method.) after which
ACPI video backlight support doesn't work on a number of systems,
because the relevant AML methods in the ACPI tables in their BIOSes
become useless after the BIOS has been told that the OS is compatible
with Windows 8. That problem is tracked by the bug entry at:
https://bugzilla.kernel.org/show_bug.cgi?id=51231
Commit
8c5bd7a (ACPI / video / i915: No ACPI backlight if firmware
expects Windows 8) introduced for this purpose essentially prevented
the ACPI backlight support from being used if the BIOS had been told
that the OS was compatible with Windows 8 and the i915 driver was
loaded, in which case the backlight would always be handled by i915.
Unfortunately, however, that turned out to cause problems with
backlight to appear on multiple systems with symptoms indicating that
i915 was unable to control the backlight on those systems as
expected.
For this reason, revert commit
8c5bd7a, but leave the function
acpi_video_backlight_quirks() introduced by it, because another
commit on top of it uses that function.
References: https://lkml.org/lkml/2013/7/21/119
References: https://lkml.org/lkml/2013/7/22/261
References: https://lkml.org/lkml/2013/7/23/429
References: https://lkml.org/lkml/2013/7/23/459
References: https://lkml.org/lkml/2013/7/23/81
References: https://lkml.org/lkml/2013/7/24/27
Reported-and-tested-by: James Hogan <james@albanarts.com>
Reported-and-tested-by: Kamal Mostafa <kamal@canonical.com>
Reported-and-tested-by: Jörg Otte <jrg.otte@gmail.com>
Reported-and-tested-by: Steven Newbury <steve@snewbury.org.uk>
Reported-by: Martin Steigerwald <Martin@lichtvoll.de>
Reported-by: Kalle Valo <kvalo@adurom.com>
Tested-by: Joerg Platte <jplatte@naasa.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tejun Heo [Fri, 26 Jul 2013 12:57:56 +0000 (08:57 -0400)]
ahci_imx: depend on CONFIG_MFD_SYSCON
ahci_imx makes use of regmap but the dependency wasn't specified in
Kconfig leading build failures if CONFIG_AHCI_IMX is enabled but
CONFIG_MFD_SYSCON is not. Add the Kconfig dependency.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Steven Rostedt (Red Hat) [Wed, 24 Jul 2013 02:21:59 +0000 (22:21 -0400)]
tracing: Remove locking trace_types_lock from tracing_reset_all_online_cpus()
Commit
a82274151af "tracing: Protect ftrace_trace_arrays list in trace_events.c"
added taking the trace_types_lock mutex in trace_events.c as there were
several locations that needed it for protection. Unfortunately, it also
encapsulated a call to tracing_reset_all_online_cpus() which also takes
the trace_types_lock, causing a deadlock.
This happens when a module has tracepoints and has been traced. When the
module is removed, the trace events module notifier will grab the
trace_types_lock, do a bunch of clean ups, and also clears the buffer
by calling tracing_reset_all_online_cpus. This doesn't happen often
which explains why it wasn't caught right away.
Commit
a82274151af was marked for stable, which means this must be
sent to stable too.
Link: http://lkml.kernel.org/r/51EEC646.7070306@broadcom.com
Reported-by: Arend van Spril <arend@broadcom.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Cc: Alexander Z Lam <azl@google.com>
Cc: Vaibhav Nagarnaik <vnagarnaik@google.com>
Cc: David Sharp <dhsharp@google.com>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Feng Kan [Tue, 23 Jul 2013 17:52:31 +0000 (18:52 +0100)]
arm64: Change kernel stack size to 16K
Written by Catalin Marinas, tested by APM on storm platform. This is needed
because of the failures encountered when running SpecWeb benchmark test.
Signed-off-by: Feng Kan <fkan@apm.com>
Acked-by: Kumar Sankaran <ksankaran@apm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Dave Airlie [Fri, 26 Jul 2013 10:38:14 +0000 (20:38 +1000)]
Merge tag 'drm-intel-fixes-2013-07-25' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Brown-paper-bag pull request here. The snb rc6 fix from the last pull
broke forcewake BIOS dirt cleanup, which with fixed. But that fix broke
the spinlock init sequence, which results in an ugly BUG when spinlock
debugging is enabled :( So I get to throw another patch at cc: stable to
fix up the mess ...
* tag 'drm-intel-fixes-2013-07-25' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: initialize gt_lock early with other spin locks
drm/i915: fix hdmi portclock limits
Dave Airlie [Fri, 26 Jul 2013 10:37:15 +0000 (20:37 +1000)]
Merge branch 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
r600 dpm fixes, old school card dac fixes, lockup fixes
endian fixes
* 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/dpm: fix r600_enable_sclk_control()
drm/radeon/dpm: implement force performance levels for rv6xx
drm/radeon/dpm: fix displaygap programming on rv6xx
drm/radeon/dpm: fix a typo in the rv6xx mclk setup
drm/radeon: fix combios tables on older cards
drm/radeon: improve dac adjust heuristics for legacy pdac
drm/radeon: Another card with wrong primary dac adj
drm/radeon: fix endian issues with DP handling (v3)
drm/radeon/vm: only align the pt base to 32k
drm/radeon: wait for 3D idle before using CP DMA
Alex Deucher [Fri, 26 Jul 2013 01:46:21 +0000 (21:46 -0400)]
drm/radeon/dpm: fix r600_enable_sclk_control()
Actually program the correct register to enable
engine clock scaling control.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Fri, 26 Jul 2013 00:07:25 +0000 (20:07 -0400)]
drm/radeon/dpm: implement force performance levels for rv6xx
Allows you to limit the selected power levels via sysfs.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Olof Johansson [Wed, 24 Jul 2013 15:42:27 +0000 (08:42 -0700)]
mfd: max8925: fix dt code for backlight
The device-tree enablement for max8925 has several problems, but besides
the bindings being wrong (and not having seen review) there's also some
bad coding practices on how to fill in the platform_data from device tree.
I came across this since it causes a warning when compiling
mmp2_defconfig, and instead of doing the minimal fix to silence the
warning, I restructured the code a bit.
This silences the warning:
drivers/video/backlight/max8925_bl.c: In function 'max8925_backlight_probe':
drivers/video/backlight/max8925_bl.c:177:3: warning: statement with no effect [-Wunused-value]
Note that the bindings themselves need to be revisited too, but that will
affect more than just the backlight driver and is best done separately;
this just fixes the bad code for the backlight driver.
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Alex Deucher [Thu, 25 Jul 2013 22:29:14 +0000 (18:29 -0400)]
drm/radeon/dpm: fix displaygap programming on rv6xx
Need to use the driver state rather than the register
state since the displays may not be enabled when the
power state is programmed.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Thu, 25 Jul 2013 22:27:45 +0000 (18:27 -0400)]
drm/radeon/dpm: fix a typo in the rv6xx mclk setup
Need to set high for the last two entries. Looks
like a copy and paste typo.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chen Wang [Fri, 19 Jul 2013 02:15:18 +0000 (10:15 +0800)]
USB: usb-skeleton.c: add retry for nonblocking read
Updated skel_read() in usb-skeleton.c. When there is no data in the
buffer, we would allow retry for both blocking and nonblocking cases.
Original logic give retry only for blocking case. Actually we can also
allow retry for nonblocking case. This will reuse the existing retry
logic and handle the return of -EAGAIN in one place. Also if the data to
be read is short and can be retrieved in quick time, we can also give a
chance for nonblocking case and may catch the data and copy it back to
userspace in one read() call too.
Signed-off-by: Chen Wang <unicornxx.wang@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Mon, 15 Jul 2013 08:59:41 +0000 (11:59 +0300)]
usbtmc: convert to devm_kzalloc
kfree(data) will be called implicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Mon, 15 Jul 2013 08:59:43 +0000 (11:59 +0300)]
usbtmc: remove redundant braces
There is a few cases where braces are not needed. This patch removes
unnecessary '& 255' pieces as well when lvalue type is u8.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Mon, 15 Jul 2013 08:59:42 +0000 (11:59 +0300)]
usbtmc: call pr_err instead of plain printk
Additionally remove useless label.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Mon, 15 Jul 2013 08:59:40 +0000 (11:59 +0300)]
usbtmc: remove trailing spaces
Recent patch series introduces few trailing spaces. This patch removes them.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Fri, 12 Jul 2013 08:04:18 +0000 (10:04 +0200)]
usbfs: Allow printer class 'get_device_id' without needing to claim the intf
For certain (HP) printers the printer device_id does not only contain a
static part identifying the printer, but it also contains a dynamic part
giving printer status, ink level, etc.
To get to this info various userspace utilities need to be able to make a
printer class 'get_device_id' request without first claiming the interface
(as that is in use for the actual printer driver).
Since the printer class 'get_device_id' request does not change interface
settings in anyway, allowing this without claiming the interface should not
cause any issues.
CC: Sanjay Kumar <sanjay.kumar14@hp.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roger Quadros [Mon, 22 Jul 2013 12:04:50 +0000 (15:04 +0300)]
USB: host: Use usb_hcd_platform_shutdown() wherever possible
Most HCD drivers are doing the same thing in their ".shutdown" callback
so it makes sense to use the generic usb_hcd_platform_shutdown()
handler there.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Thu, 11 Jul 2013 18:58:23 +0000 (14:58 -0400)]
USB: remove redundant "#if"
This patch removes a redundant nested "#ifdef CONFIG_PM" from the hub
driver. It also adds a label to the "#endif" line corresponding to
the outer "#ifdef CONFIG_PM".
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Manu Gautam [Wed, 3 Jul 2013 03:13:51 +0000 (20:13 -0700)]
usb: misc: EHSET Test Fixture device driver for host compliance
An Embedded Host High-Speed Electrical Test (EHSET) test fixture is
used to initiate test modes on a host controller in order to perform
the high speed electrical testing procedure for USB-IF compliance.
When this test fixture is connected to a host, it can enumerate as
one of several selectable VID/PID pairs, each corresponding to one
of the following test modes:
* TEST_SE0_NAK
* TEST_J
* TEST_K
* TEST_PACKET
* HS_HOST_PORT_SUSPEND_RESUME
* SINGLE_STEP_GET_DEV_DESC
* SINGLE_STEP_SET_FEATURE
The USB EHSET procedure can be found here:
http://www.usb.org/developers/onthego/EHSET_v1.01.pdf
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
[jackp@codeaurora.org: imported from commit
073c9409 on codeaurora.org;
minor cleanup and updated author email]
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felipe Balbi [Tue, 2 Jul 2013 07:50:15 +0000 (10:50 +0300)]
usb: clamp bInterval to allowed range
bInterval must be within the range 1 - 16
when running at High/Super speed, and within
the range 1 - 255 when running at Full/Low speed.
In order to catch drivers passing a too
large bInterval on Super/High speed scenarios
(thus overflowing urb->interval), let's clamp()
the argument to the allowed ranges.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felipe Balbi [Mon, 1 Jul 2013 08:23:23 +0000 (11:23 +0300)]
usb: atm: speedtch: be careful with bInterval
bInterval must be on the range 1 - 16, if we
want to pass the maximum allowed, we should
be passing 16.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felipe Balbi [Mon, 1 Jul 2013 08:23:24 +0000 (11:23 +0300)]
usb: class: cdc-acm: be careful with bInterval
bInterval must be on the range 1 - 16, if we
want to pass the maximum allowed, we should
be passing 16
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
William Gulland [Thu, 27 Jun 2013 23:10:20 +0000 (16:10 -0700)]
usb: Clear both buffers when clearing a control transfer TT buffer.
Control transfers have both IN and OUT (or SETUP) packets, so when
clearing TT buffers for a control transfer it's necessary to send
two HUB_CLEAR_TT_BUFFER requests to the hub.
Signed-off-by: William Gulland <wgulland@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrzej Pietrasiewicz [Thu, 25 Jul 2013 07:13:18 +0000 (09:13 +0200)]
usb/gadget: free opts struct on error recovery
Fix memory leaks introduced in commits:
40d133d7f542616cf9538508a372306e626a16e9
usb: gadget: f_ncm: convert to new function interface with backward compatibility
fee562a6450b7806f1fbbe1469a67b5395b5c10a
usb: gadget: f_ecm: convert to new function interface with backward compatibility
fcbdf12ebef73a6069e2a1aada1e546fb578a4aa
usb: gadget: f_phonet: convert to new function interface with backward compatibility
b29002a157940752dfed2c488b2011f63f007d71
usb: gadget: f_eem: convert to new function interface with backward compatibility
8cedba7c73af1369599b1111639cfeb66fe13aaa
usb: gadget: f_subset: convert to new function interface with backward compatibility
f466c6353819326873fa48a02c6f2d7c903240d6
usb: gadget: f_rndis: convert to new function interface with backward compatibility
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 1 Jul 2013 12:03:33 +0000 (14:03 +0200)]
USB: mos7840: fix memory leak in open
Allocated urbs and buffers were never freed on errors in open.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enrico Mioso [Sat, 13 Jul 2013 16:54:14 +0000 (18:54 +0200)]
usb: serial: option.c: remove ONDA MT825UP product ID fromdriver
Some (very few) early devices like mine, where not exposting a proper CDC
descriptor. This was fixed with an immediate firmware update from the vendor,
and pre-installed on newer devices.
So actual devices can be driven by cdc_acm.c + cdc_ether.c.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Williams [Wed, 10 Jul 2013 17:25:02 +0000 (12:25 -0500)]
usb: serial: option: add Olivetti Olicard 200
Speaks AT on interfaces 5 (command & PPP) and 3 (secondary), other
interface protocols are unknown.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enrico Mioso [Sat, 29 Jun 2013 13:33:35 +0000 (15:33 +0200)]
usb: serial: option: blacklist ONDA MT689DC QMI interface
Prevent the option driver from binding itself to the QMI/WWAN interface, making
it unusable by the proper driver.
Signed-off-by: enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Thu, 25 Jul 2013 17:02:24 +0000 (10:02 -0700)]
Merge tag 'for-usb-linus-2013-07-25' of git://git./linux/kernel/git/sarah/xhci into usb-linus
Sarah writes:
xhci: Bug fixes, now with more tags!
Hi Greg,
Here's five bug fixes for 3.12.
The three patches are marked for stable. Two fix NULL pointer dereferences.
The third marked for stable suppresses some serious log spam from unnecessary
xHCI driver warnings, whenever an isochronous short packet happens on an xHCI
1.0 host.
The other two patches fix build warnings.
Sarah Sharp
Dave Chinner [Wed, 24 Jul 2013 05:47:30 +0000 (15:47 +1000)]
xfs: di_flushiter considered harmful
When we made all inode updates transactional, we no longer needed
the log recovery detection for inodes being newer on disk than the
transaction being replayed - it was redundant as replay of the log
would always result in the latest version of the inode would be on
disk. It was redundant, but left in place because it wasn't
considered to be a problem.
However, with the new "don't read inodes on create" optimisation,
flushiter has come back to bite us. Essentially, the optimisation
made always initialises flushiter to zero in the create transaction,
and so if we then crash and run recovery and the inode already on
disk has a non-zero flushiter it will skip recovery of that inode.
As a result, log recovery does the wrong thing and we end up with a
corrupt filesystem.
Because we have to support old kernel to new kernel upgrades, we
can't just get rid of the flushiter support in log recovery as we
might be upgrading from a kernel that doesn't have fully transactional
inode updates. Unfortunately, for v4 superblocks there is no way to
guarantee that log recovery knows about this fact.
We cannot add a new inode format flag to say it's a "special inode
create" because it won't be understood by older kernels and so
recovery could do the wrong thing on downgrade. We cannot specially
detect the combination of zero mode/non-zero flushiter on disk to
non-zero mode, zero flushiter in the log item during recovery
because wrapping of the flushiter can result in false detection.
Hence that makes this "don't use flushiter" optimisation limited to
a disk format that guarantees that we don't need it. And that means
the only fix here is to limit the "no read IO on create"
optimisation to version 5 superblocks....
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit
e60896d8f2b81412421953e14d3feb14177edb56)
Linus Walleij [Mon, 22 Jul 2013 23:43:20 +0000 (01:43 +0200)]
pinctrl: fix a memleak when freeing maps
We forgot to free the node itself when free:ing a map.
Reported-by: xulinuxkernel <xulinuxkernel@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Oleksij Rempel [Sun, 21 Jul 2013 13:36:19 +0000 (15:36 +0200)]
xhci: fix null pointer dereference on ring_doorbell_for_active_rings
in some cases where device is attched to xhci port and do not responding,
for example ath9k_htc with stalled firmware, kernel will
crash on ring_doorbell_for_active_rings.
This patch check if pointer exist before it is used.
This patch should be backported to kernels as old as 2.6.35, that
contain the commit
e9df17eb1408cfafa3d1844bfc7f22c7237b31b8 "USB: xhci:
Correct assumptions about number of rings per endpoint"
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
George Cherian [Mon, 1 Jul 2013 05:29:12 +0000 (10:59 +0530)]
usb: host: xhci: Enable XHCI_SPURIOUS_SUCCESS for all controllers with xhci 1.0
Xhci controllers with hci_version > 0.96 gives spurious success
events on short packet completion. During webcam capture the
"ERROR Transfer event TRB DMA ptr not part of current TD" was observed.
The same application works fine with synopsis controllers hci_version 0.96.
The same issue is seen with Intel Pantherpoint xhci controller. So enabling
this quirk in xhci_gen_setup if controller verion is greater than 0.96.
For xhci-pci move the quirk to much generic place xhci_gen_setup.
Note from Sarah:
The xHCI 1.0 spec changed how hardware handles short packets. The HW
will notify SW of the TRB where the short packet occurred, and it will
also give a successful status for the last TRB in a TD (the one with the
IOC flag set). On the second successful status, that warning will be
triggered in the driver.
Software is now supposed to not assume the TD is not completed until it
gets that last successful status. That means we have a slight race
condition, although it should have little practical impact. This patch
papers over that issue.
It's on my long-term to-do list to fix this race condition, but it is a
much more involved patch that will probably be too big for stable. This
patch is needed for stable to avoid serious log spam.
This patch should be backported to kernels as old as 3.0, that
contain the commit
ad808333d8201d53075a11bc8dd83b81f3d68f0b "Intel xhci:
Ignore spurious successful event."
The patch will have to be modified for kernels older than 3.2, since
that kernel added the xhci_gen_setup function for xhci platform devices.
The correct conflict resolution for kernels older than 3.2 is to set
XHCI_SPURIOUS_SUCCESS in xhci_pci_quirks for all xHCI 1.0 hosts.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Randy Dunlap [Tue, 23 Jul 2013 22:22:59 +0000 (15:22 -0700)]
usb: fix build warning in pci-quirks.h when CONFIG_PCI is not enabled
Fix warning when CONFIG_PCI is not enabled
(from commit
296365781903226a3fb8758901eaeec09d2798e4).
drivers/usb/host/pci-quirks.h: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Olof Johansson [Tue, 23 Jul 2013 18:58:20 +0000 (11:58 -0700)]
usb: xhci: Mark two functions __maybe_unused
Resolves the following build warnings:
drivers/usb/host/xhci.c:332:13: warning: 'xhci_msix_sync_irqs' defined but not used [-Wunused-function]
drivers/usb/host/xhci.c:3901:12: warning: 'xhci_change_max_exit_latency' defined but not used [-Wunused-function]
These functions are not always used, and since they're marked static
they will produce build warnings:
- xhci_msix_sync_irqs is only used with CONFIG_PCI.
- xhci_change_max_exit_latency is a little more complicated with
dependencies on CONFIG_PM and CONFIG_PM_RUNTIME.
Instead of building a bigger maze of ifdefs in this code, I've just
marked both with __maybe_unused.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Sarah Sharp [Wed, 24 Jul 2013 17:27:13 +0000 (10:27 -0700)]
xhci: Avoid NULL pointer deref when host dies.
When the host controller fails to respond to an Enable Slot command, and
the host fails to respond to the register write to abort the command
ring, the xHCI driver will assume the host is dead, and call
usb_hc_died().
The USB device's slot_id is still set to zero, and the pointer stored at
xhci->devs[0] will always be NULL. The call to xhci_check_args in
xhci_free_dev should have caught the NULL virt_dev pointer.
However, xhci_free_dev is designed to free the xhci_virt_device
structures, even if the host is dead, so that we don't leak kernel
memory. xhci_free_dev checks the return value from the generic
xhci_check_args function. If the return value is -ENODEV, it carries on
trying to free the virtual device.
The issue is that xhci_check_args looks at the host controller state
before it looks at the xhci_virt_device pointer. It will return -ENIVAL
because the host is dead, and xhci_free_dev will ignore the return
value, and happily dereference the NULL xhci_virt_device pointer.
The fix is to make sure that xhci_check_args checks the xhci_virt_device
pointer before it checks the host state.
See https://bugs.launchpad.net/ubuntu/+source/linux/+bug/
1203453 for
further details. This patch doesn't solve the underlying issue, but
will ensure we don't see any more NULL pointer dereferences because of
the issue.
This patch should be backported to kernels as old as 3.1, that
contain the commit
7bd89b4017f46a9b92853940fd9771319acb578a "xhci: Don't
submit commands or URBs to halted hosts."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Vincent Thiele <vincentthiele@gmail.com>
Cc: stable@vger.kernel.org
Jani Nikula [Thu, 25 Jul 2013 09:44:34 +0000 (12:44 +0300)]
drm/i915: initialize gt_lock early with other spin locks
commit
181d1b9e31c668259d3798c521672afb8edd355c
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jul 21 13:16:24 2013 +0200
drm/i915: fix up gt init sequence fallout
moved dev_priv->gt_lock initialization after use. Do the initialization
much earlier with other spin lock initializations.
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: stable@vger.kernel.org (since the regressing patch is also cc: stable)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
NeilBrown [Mon, 22 Jul 2013 02:57:21 +0000 (12:57 +1000)]
md/raid5: fix interaction of 'replace' and 'recovery'.
If a device in a RAID4/5/6 is being replaced while another is being
recovered, then the writes to the replacement device currently don't
happen, resulting in corruption when the replacement completes and the
new drive takes over.
This is because the replacement writes are only triggered when
's.replacing' is set and not when the similar 's.sync' is set (which
is the case during resync and recovery - it means all devices need to
be read).
So schedule those writes when s.replacing is set as well.
In this case we cannot use "STRIPE_INSYNC" to record that the
replacement has happened as that is needed for recording that any
parity calculation is complete. So introduce STRIPE_REPLACED to
record if the replacement has happened.
For safety we should also check that STRIPE_COMPUTE_RUN is not set.
This has a similar effect to the "s.locked == 0" test. The latter
ensure that now IO has been flagged but not started. The former
checks if any parity calculation has been flagged by not started.
We must wait for both of these to complete before triggering the
'replace'.
Add a similar test to the subsequent check for "are we finished yet".
This possibly isn't needed (is subsumed in the STRIPE_INSYNC test),
but it makes it more obvious that the REPLACE will happen before we
think we are finished.
Finally if a NeedReplace device is not UPTODATE then that is an
error. We really must trigger a warning.
This bug was introduced in commit
9a3e1101b827a59ac9036a672f5fa8d5279d0fe2
(md/raid5: detect and handle replacements during recovery.)
which introduced replacement for raid5.
That was in 3.3-rc3, so any stable kernel since then would benefit
from this fix.
Cc: stable@vger.kernel.org (3.3+)
Reported-by: qindehua <13691222965@163.com>
Tested-by: qindehua <qindehua@163.com>
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Wed, 24 Jul 2013 05:37:42 +0000 (15:37 +1000)]
md/raid10: remove use-after-free bug.
We always need to be careful when calling generic_make_request, as it
can start a chain of events which might free something that we are
using.
Here is one place I wasn't careful enough. If the wbio2 is not in
use, then it might get freed at the first generic_make_request call.
So perform all necessary tests first.
This bug was introduced in 3.3-rc3 (
24afd80d99) and can cause an
oops, so fix is suitable for any -stable since then.
Cc: stable@vger.kernel.org (3.3+)
Signed-off-by: NeilBrown <neilb@suse.de>
Tsugikazu Shibata [Thu, 25 Jul 2013 00:17:23 +0000 (09:17 +0900)]
HOWTO ja_JP sync
Attached is Documentation/ja_JP/HOWTO sync patch for 3.10.
This patch was reviewed by Japanese translation community called JF.
Signed-off-by: Tsugikazu Shibata <tshibata@ab.jp.nec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enrico Mioso [Thu, 25 Jul 2013 00:01:39 +0000 (02:01 +0200)]
usb: serial: option: Add ONYX 3G device support
This patch adds support for the ONYX 3G device (version 1) from ALFA
NETWORK.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Olof Johansson [Thu, 25 Jul 2013 00:06:47 +0000 (17:06 -0700)]
Merge tag 'samsung-fixes-1' of git://git./linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim:
Samsung fixes for v3.11
- fix kernel booting on exynos5440
skip pm which is not supported
update regarding LPAE features
- fix s3c2440 uart with adding clkdev entries
- fix compilatioin for Samsung SoCs with selecting pm
- update ARCH_NR_GPIO to support exynos4412 has more gpios
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
ARM: EXYNOS: Fix low level debug support
ARM: SAMSUNG: Save/restore only selected uart's registers
ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
ARM: EXYNOS: Enable 64-bit DMA for EXYNOS5440 if LPAE is enabled
ARM: EXYNOS: change the PHYSMEM_BITS and SECTION_SIZE
ARM: EXYNOS: skip pm support on exynos5440
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 24 Jul 2013 23:55:23 +0000 (16:55 -0700)]
ARM: omap5: Only select errata 798181 if SMP
Avoids the following warning when SMP is off:
warning: (ARCH_KEYSTONE && SOC_OMAP5) selects ARM_ERRATA_798181 which
has unmet direct dependencies (CPU_V7 && SMP)
Reported-by: Emilio López <emilio@elopez.com.ar>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Greg Kroah-Hartman [Wed, 24 Jul 2013 23:10:58 +0000 (16:10 -0700)]
Revert "usb: host: Faraday fotg210-hcd driver"
This reverts commit
1dd3d123239179fad5de5dc00a6e0014a1918fde.
The email address for the developer now bounces, which means they have
moved on, so remove the driver until someone else from the company steps
up to maintain it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yuan-Hsin Chen [Wed, 19 Jun 2013 19:53:04 +0000 (19:53 +0000)]
usb: host: Faraday fotg210-hcd driver
FOTG210 is an OTG controller which can be configured as an
USB2.0 host. FOTG210 host is an ehci-like controller with
some differences. First, register layout of FOTG210 is
incompatible with EHCI. Furthermore, FOTG210 is lack of
siTDs which means iTDs are used for both HS and FS ISO
transfer.
Signed-off-by: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Fri, 28 Jun 2013 10:24:26 +0000 (12:24 +0200)]
USB: ti_usb_3410_5052: fix dynamic-id matching
The driver failed to take the dynamic ids into account when determining
the device type and therefore all devices were detected as 2-port
devices when using the dynamic-id interface.
Match on the usb-serial-driver field instead of doing redundant id-table
searches.
Reported-by: Anders Hammarquist <iko@iko.pp.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ming Lei [Fri, 28 Jun 2013 01:38:12 +0000 (09:38 +0800)]
USB: check sg buffer size in usb_submit_urb
USB spec stats that short packet can only appear at the end
of transfer. Because lost of HC(EHCI/UHCI/OHCI/...) can't
build a full packet from discontinuous buffers, we introduce
the limit in usb_submit_urb() to avoid such kind of bad sg buffers
coming from driver.
The limit might be a bit strict:
- platform has iommu to do sg list mapping
- some host controllers may support to build full packet from
discontinuous buffers.
But considered that most of HCs don't support that, and driver
need work well or keep consistent on different HCs and ARCHs, we
have to introduce the limit.
Currently, only usbtest is reported to pass such sg buffers to HC,
and other users(mass storage, usbfs) don't have the problem.
We don't check it on USB wireless device, because:
- wireless devices can't be attached to common USB
bus(EHCI/UHCI/OHCI/...)
- the max packet size of endpoint may be odd, and often can't
devide 4KB which is a typical usage in usb mass storage application
Reported-by: Konstantin Filatov <kfilatov@parallels.com>
Reported-by: Denis V. Lunev <den@openvz.org>
Cc: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Richard Zhao [Sun, 21 Jul 2013 02:43:26 +0000 (10:43 +0800)]
serial: tegra: correct help message in Kconfig from 'ttyHS' to 'ttyTHS'
ttyTHS is consistent with the name used in driver.
Signed-off-by: Richard Zhao <rizhao@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Henrik Nordström [Tue, 23 Jul 2013 19:06:07 +0000 (21:06 +0200)]
tty/8250_early: Don't truncate last character of options
The earlier change to use strlcpy uncovered a bug in the options
argument length calculation causing last character to be truncated.
This makes the actual console to be configured with incorrect
baudrate when specifying the console using console=uart,... syntax.
Bug symptom seen in kernel log output:
Kernel command line: console=uart,mmio,0x90000000,115200
Early serial console at MMIO 0x90000000 (options '11520')
which then results in a invalid baud rate 11520 instead of the
expected 115200 when the console is switched to ttyS0 later
in the boot process.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Fri, 19 Jul 2013 05:53:13 +0000 (08:53 +0300)]
TTY: snyclinkmp: calculating wrong addresses
This is a static checker fix and I don't have a way to test it. But
from the context it looks like this is a typo where SCABUFSIZE was
intended instead of sizeof(SCABUFSIZE). SCABUFSIZE is 1024 and
sizeof(int) is 4. I would suspect this is a bad bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Tue, 2 Jul 2013 19:22:07 +0000 (12:22 -0700)]
USB: isp1362: move debug files from proc to debugfs
Drivers should not be putting debug files in /proc/ that is what debugfs
is for, so move the isp1362 driver's debug file to debugfs.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Tue, 2 Jul 2013 19:22:06 +0000 (12:22 -0700)]
USB: sl811: move debug files from proc to debugfs
Drivers should not be putting debug files in /proc/ that is what debugfs
is for, so move the sl811 driver's debug file to debugfs.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Tue, 2 Jul 2013 19:22:05 +0000 (12:22 -0700)]
USB: remove unneeded idr.h include
None of these USB files need idr.h, so don't include it.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Bottomley [Wed, 24 Jul 2013 19:43:18 +0000 (12:43 -0700)]
[SCSI] isci: fix breakage caused by >16byte CDB patch
Oops, apparently no-one I cc'd at intel actually bothered to check this
patch for the isci driver:
commit
e73823f7a2c921dcf068d34ea03bd682498d9e42
Author: James Bottomley <JBottomley@Parallels.com>
Date: Tue May 7 15:38:18 2013 -0700
[SCSI] libsas: implement > 16 byte CDB support
sci_swab32_cpy needs multiples of four, so for commands that aren't that, it's
rounding the wrong way. fix by doing (len+3)/4 instead of len/4.
Reported-by: Tony Luck <tony.luck@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Linus Torvalds [Wed, 24 Jul 2013 18:07:18 +0000 (11:07 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here is a series of powerpc fixes. It's a bit big, mostly because of
the series of 11 "EEH" patches from Gavin. The EEH (Our IBM specific
PCI/PCIe Enhanced Error Handling) code had been rotting for a while
and this merge window saw a significant rework & fixing of it by Gavin
Shan.
However, that wasn't complete and left some open issues. There were
still a few corner cases that didn't work properly, for example in
relation to hotplug and devices without explicit error handlers. We
had some patches but they weren't quite good enough yet so I left them
off the 3.11 merge window.
Gavin since then fixed it all up, we ran quite a few rounds of testing
and it seems fairly solid (at least probably more than it has ever
been). This should probably have made -rc1 but both Gavin and I took
some vacation so it had to wait for -rc2.
The rest is more bug fixes, mostly to new features recently added, for
example, we missed the cpu table entry for one of the two models of P8
(we didn't realize they had different PVR [Processor Version Register]
values), some module CRC issues, etc..."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (23 commits)
powerpc/perf: BHRB filter configuration should follow the task
powerpc/perf: Ignore separate BHRB privilege state filter request
powerpc/powernv: Mark pnv_pci_init_ioda2_phb() as __init
powerpc/mm: Use the correct SLB(LLP) encoding in tlbie instruction
powerpc/mm: Fix fallthrough bug in hpte_decode
powerpc/pseries: Fix a typo in pSeries_lpar_hpte_insert()
powerpc/eeh: Introdce flag to protect sysfs
powerpc/eeh: Fix unbalanced enable for IRQ
powerpc/eeh: Don't use pci_dev during BAR restore
powerpc/eeh: Use partial hotplug for EEH unaware drivers
powerpc/pci: Partial tree hotplug support
powerpc/eeh: Use safe list traversal when walking EEH devices
powerpc/eeh: Keep PE during hotplug
powerpc/pci/hotplug: Don't need to remove from EEH cache twice
powerpc/pci: Override pcibios_release_device()
powerpc/eeh: Export functions for hotplug
powerpc/eeh: Remove reference to PCI device
powerpc: Fix the corrupt r3 error during MCE handling.
powerpc/perf: Set PPC_FEATURE2_EBB when we register the power8 PMU
powerpc/pseries: Drop "select HOTPLUG"
...
Linus Torvalds [Wed, 24 Jul 2013 18:05:18 +0000 (11:05 -0700)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This push fixes a memory corruption issue in caam, as well as
reverting the new optimised crct10dif implementation as it breaks boot
on initrd systems.
Hopefully crct10dif will be reinstated once the supporting code is
added so that it doesn't break boot"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
Revert "crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework"
crypto: caam - Fixed the memory out of bound overwrite issue
Lidza Louina [Wed, 24 Jul 2013 15:29:33 +0000 (11:29 -0400)]
MAINTAINERS: Update the list of maintainers for staging/comedi driver.
This patch updates the list of maintainers for the staging/comedi
driver.
Signed-off-by: Lidza Louina <lidza.louina@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jingoo Han [Wed, 24 Jul 2013 05:34:08 +0000 (14:34 +0900)]
staging: tidspbridge: replace strict_strtol() with kstrtos32()
The usage of strict_strtol() is not preferred, because
strict_strtol() is obsolete. Thus, kstrtos32() should be
used in order to convert a string to s32. Also, error handling
is added to get rid of a __must_check warning.
This fixes a memory corruption bug as well.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Richard Zhu [Wed, 24 Jul 2013 06:15:29 +0000 (14:15 +0800)]
ahci_imx: add ahci sata support on imx platforms
imx6q contains one Synopsys AHCI SATA controller, But it can't share
ahci_platform driver with other controllers because there are some
misalignments of the generic AHCI controller - the bits definitions of
the HBA registers, the Vendor Specific registers, the AHCI PHY clock
and the AHCI signals adjustment window(GPR13 register).
- CAP_SSS(bit20) of the HOST_CAP is writable, default value is '0',
should be configured to be '1'
- bit0 (only one AHCI SATA port on imx6q) of the HOST_PORTS_IMPL
should be set to be '1'.(default 0)
- One Vendor Specific register HOST_TIMER1MS(offset:0xe0) should be
configured regarding to the frequency of AHB bus clock.
- Configurations of the AHCI PHY clock, and the signal parameters of
the GPR13
Setup its own ahci sata driver, contained the imx6q specific
initialized codes, re-use the generic ahci_platform driver, and keep
the generic ahci_platform driver clean as much as possible.
tj: patch description reformatted
Signed-off-by: Richard Zhu <r65037@freescale.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Richard Zhu [Wed, 24 Jul 2013 06:15:28 +0000 (14:15 +0800)]
ARM: imx6q: update the sata bits definitions of gpr13
Replace the SATA_PHY_# by the more readable definitons.
tj: Being routed through libata branch to enable implementation of
ahci_imx.
Signed-off-by: Richard Zhu <r65037@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Greg Kroah-Hartman [Wed, 24 Jul 2013 16:07:32 +0000 (09:07 -0700)]
Merge tag 'for-usb-next-2013-07-23' of git://git./linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Features for 3.12
In the spirit of "let's stop gossiping around the water cooler and get to work",
here's some xHCI patches for 3.12.
They include a patch for suspend/resume support for xhci platform hosts, two
patches to support showing USB 2.1 link status, and a patch to future-proof the
Intel EHCI to xHCI port switchover.
Sarah Sharp
Steven Rostedt (Red Hat) [Wed, 24 Jul 2013 02:06:15 +0000 (22:06 -0400)]
ftrace: Add check for NULL regs if ops has SAVE_REGS set
If a ftrace ops is registered with the SAVE_REGS flag set, and there's
already a ops registered to one of its functions but without the
SAVE_REGS flag, there's a small race window where the SAVE_REGS ops gets
added to the list of callbacks to call for that function before the
callback trampoline gets set to save the regs.
The problem is, the function is not currently saving regs, which opens
a small race window where the ops that is expecting regs to be passed
to it, wont. This can cause a crash if the callback were to reference
the regs, as the SAVE_REGS guarantees that regs will be set.
To fix this, we add a check in the loop case where it checks if the ops
has the SAVE_REGS flag set, and if so, it will ignore it if regs is
not set.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Oleg Nesterov [Tue, 23 Jul 2013 15:26:13 +0000 (17:26 +0200)]
tracing: Kill trace_cpu struct/members
After the previous changes trace_array_cpu->trace_cpu and
trace_array->trace_cpu becomes write-only. Remove these members
and kill "struct trace_cpu" as well.
As a side effect this also removes memset(per_cpu_memory, 0).
It was not needed, alloc_percpu() returns zero-filled memory.
Link: http://lkml.kernel.org/r/20130723152613.GA23741@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Oleg Nesterov [Tue, 23 Jul 2013 15:26:10 +0000 (17:26 +0200)]
tracing: Change tracing_fops/snapshot_fops to rely on tracing_get_cpu()
tracing_open() and tracing_snapshot_open() are racy, the memory
inode->i_private points to can be already freed.
Convert these last users of "inode->i_private == trace_cpu" to
use "i_private = trace_array" and rely on tracing_get_cpu().
v2: incorporate the fix from Steven, tracing_release() must not
blindly dereference file->private_data unless we know that
the file was opened for reading.
Link: http://lkml.kernel.org/r/20130723152610.GA23737@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Oleg Nesterov [Tue, 23 Jul 2013 15:26:06 +0000 (17:26 +0200)]
tracing: Change tracing_entries_fops to rely on tracing_get_cpu()
tracing_open_generic_tc() is racy, the memory inode->i_private
points to can be already freed.
1. Change its last user, tracing_entries_fops, to use
tracing_*_generic_tr() instead.
2. Change debugfs_create_file("buffer_size_kb", data) callers
to pass "data = tr".
3. Change tracing_entries_read() and tracing_entries_write() to
use tracing_get_cpu().
4. Kill the no longer used tracing_open_generic_tc() and
tracing_release_generic_tc().
Link: http://lkml.kernel.org/r/20130723152606.GA23730@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Oleg Nesterov [Tue, 23 Jul 2013 15:26:03 +0000 (17:26 +0200)]
tracing: Change tracing_stats_fops to rely on tracing_get_cpu()
tracing_open_generic_tc() is racy, the memory inode->i_private
points to can be already freed.
1. Change one of its users, tracing_stats_fops, to use
tracing_*_generic_tr() instead.
2. Change trace_create_cpu_file("stats", data) to pass "data = tr".
3. Change tracing_stats_read() to use tracing_get_cpu().
Link: http://lkml.kernel.org/r/20130723152603.GA23727@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Oleg Nesterov [Tue, 23 Jul 2013 15:26:00 +0000 (17:26 +0200)]
tracing: Change tracing_buffers_fops to rely on tracing_get_cpu()
tracing_buffers_open() is racy, the memory inode->i_private points
to can be already freed.
Change debugfs_create_file("trace_pipe_raw", data) caller to pass
"data = tr", tracing_buffers_open() can use tracing_get_cpu().
Change debugfs_create_file("snapshot_raw_fops", data) caller too,
this file uses tracing_buffers_open/release.
Link: http://lkml.kernel.org/r/20130723152600.GA23720@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>