OSDN Git Service
Mark Brown [Mon, 17 Nov 2008 16:59:24 +0000 (16:59 +0000)]
ASoC: Allow writes to uncached registers in WM8990
Only fully documented registers are cached in the WM8990 but additional
registers exist.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Christian Pellegrin [Sat, 15 Nov 2008 07:58:32 +0000 (08:58 +0100)]
ASoC: Machine driver for for s3c24xx with uda134x
Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Christian Pellegrin [Sat, 15 Nov 2008 07:58:16 +0000 (08:58 +0100)]
ASoC: UDA134x codec driver
Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Peter Ujfalusi [Fri, 14 Nov 2008 06:57:28 +0000 (08:57 +0200)]
ASoC: Fix for master playback/capture volume range for TWL4030 codec
FGAIN for playback is in range of 0-0x3f, while for capture GAIN it
is in the range of 0-0x1f.
The original value of 128 (0x7f) would modify the CGAIN also for
playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 13 Nov 2008 14:33:14 +0000 (14:33 +0000)]
ASoC: Add WM8728 codec driver
The WM8728 is a high performance stereo DAC designed for applications
such as DVD, home theatre and digital TV.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 14 Nov 2008 14:40:46 +0000 (14:40 +0000)]
ASoC: Revert "ASoC: Add new parameter to s3c24xx_pcm_enqueue"
This reverts commit
8dc840f88d9c9f75f46d5dbe489242f8a114fab6. Christian
Pellegrin <chripell@gmail.com> reported that on some systems the patch
caused DMA to fail which is much more serious than the original skipped
audio issue. Further investigation by Dave shows that the behaviour
depends on the clock speed of the SoC - a better fix is neeeded.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jarkko Nikula [Wed, 12 Nov 2008 15:05:51 +0000 (17:05 +0200)]
ASoC: OMAP: Add more supported sample rates into McBSP DAI driver
Originally it was put too tight limits to support only 44.1 kHz and 48 kHz
sample rates in McBSP DAI driver. Extend it now to 8 kHz - 96 kHz. With
96 kHz and 2*16 bits, bit clock is 3.072 MHz < 3.125 MHz (I2S max?).
Tested on Nokia N810 with TVL320AIC33 from rates 8 - 96 kHz and on Texas
Instruments Beagle with TWL4030 from rates 8 - 48 kHz.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jarkko Nikula [Wed, 12 Nov 2008 15:05:41 +0000 (17:05 +0200)]
ASoC: Fix supported sample rates of TWL4030 audio codec
TWL4030 currently supports rates between 8 kHz and 48 kHz and sets the codec
mode register accordingly in twl4030_hw_params. Expose this info so that
ASoC can match other rates than 44.1 kHz or 48 kHz as well.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Naresh Medisetty [Wed, 12 Nov 2008 04:56:31 +0000 (10:26 +0530)]
ASoC: DaVinci: Audio: Fix swapping of channels at start of stereo playback
Fixes swapping of channels at start of stereo playback.
Channel swap can be observed while playing left-only or right-only audio data. The channel
swap is fixed by handling the XSYNCERR condition.
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Hugo Villeneuve [Sat, 8 Nov 2008 18:26:09 +0000 (13:26 -0500)]
ASoC: Add Right-Justified mode and Codec clock master to davinci-i2s
The TI DVEVM board uses the SND_SOC_DAIFMT_CBM_CFM & I2S formats, but the
Lyrtech SFFSDR board uses the SND_SOC_DAIFMT_CBM_CFS & RIGHT-JUSTIFIED formats.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Christian Pellegrin [Sat, 8 Nov 2008 07:44:16 +0000 (08:44 +0100)]
ASoC: s3c24xx 8 bit sound fix
fixes playing/recording of 8 bit audio files.
Generated on
20081108 against v2.6.27
Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Troy Kisky [Wed, 5 Nov 2008 18:53:28 +0000 (18:53 +0000)]
ASoC: TLV320AIC23B Support more sample rates
Add support for more sample rates, different crystals
and split playback/capture rates.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Grazvydas Ignotas [Wed, 5 Nov 2008 21:51:05 +0000 (23:51 +0200)]
ALSA: ASoC: TWL4030 codec - fix 256*Fs clock
According to TRM, 256*Fs clock output should be enabled
when TWL4030 is in slave mode, not master.
This allows sound to work on OMAP3 Pandora, which uses
256*Fs clock.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
David Anders [Wed, 5 Nov 2008 15:39:47 +0000 (07:39 -0800)]
ASoC: Add new parameter to s3c24xx_pcm_enqueue
The S3C24xx dma does not allow more than one buffer to be enqueue prior to
the dma transfers starting. This patch adds an additional parameter to
s3c24xx_pcm_enqueue() to allow for passing an initial dma maximum load
value.
Signed-off-by: David Anders <danders at amltd.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 5 Nov 2008 11:13:21 +0000 (11:13 +0000)]
ASoC: Remove core version number
Rather than try to remember to keep the core version number updated
(which hasn't been happening) just remove it. It was much more useful
when ASoC was out of tree.
Signed-off-by: Mark brown <broonie@opensource.wolfsonmicro.com>
Marek Vasut [Mon, 3 Nov 2008 12:02:12 +0000 (12:02 +0000)]
ASoC: Add Palm/PXA27x unified ASoC audio driver
this patch adds asoc audio driver for pxa27x based Palm PDAs. I tested it for
palmtx, t5 and ld, it should work with palmz72 as well (slapin, please test).
I sent it here some time ago, but now I got to fixing bugs in it. It should
be somehow mostly ok and ready for applying.
[Converted to use snd_soc_dapm_nc_pin() and bool Kconfig -- broonie]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Takashi Iwai [Tue, 4 Nov 2008 17:06:23 +0000 (18:06 +0100)]
ALSA: ASoC - Remove unnecessary inclusion of linux/version.h
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Huang Weiyi [Fri, 31 Oct 2008 14:50:00 +0000 (22:50 +0800)]
ALSA: ASoC codec: remove unused #include <version.h>
The file(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
sound/soc/codecs/
ad73311.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Troy Kisky [Mon, 3 Nov 2008 19:22:07 +0000 (12:22 -0700)]
ALSA: SOC: Fix setting codec register with debugfs filesystem merge error
Call device_create_file only once in snd_soc_dapm_sys_add function.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Fri, 31 Oct 2008 16:13:10 +0000 (17:13 +0100)]
Merge commit 'v2.6.28-rc2' into topic/asoc
Takashi Iwai [Fri, 31 Oct 2008 13:39:49 +0000 (14:39 +0100)]
Merge branch 'topic/fix/asoc' into topic/asoc
Sedji Gaouaou [Fri, 3 Oct 2008 14:58:58 +0000 (16:58 +0200)]
ASoC: Add audio support for the Atmel AT91SAM9G20ek board(uing wolfson 8731).
Add audio support for the Atmel AT91SAM9G20ek board(uing wolfson 8731).
It is based on the former eti_b1_wm8731.c file, using the atmel scc API.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sedji Gaouaou [Fri, 3 Oct 2008 14:57:50 +0000 (16:57 +0200)]
ASoC: Merge AT91 and AVR32 support into a single atmel architecture
The Ateml AT91 and AVR32 SoC share common IP for audio and can share the
same driver code using the atmel-ssc API provided for both architectures.
Do this, creating a new unified atmel ASoC architecture to replace the
previous at32 and at91 ones.
[This was contributed as a patch series for reviewability but has been
squashed down to a single commit to help preserve both the history and
bisectability. A small bugfix from Jukka is included.]
Tested-by: Jukka Hynninen <ext-jukka.hynninen@vaisala.com>
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Steve Sakoman [Fri, 31 Oct 2008 04:55:24 +0000 (21:55 -0700)]
ASoC: Add support for Beagleboard
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Steve Sakoman [Fri, 31 Oct 2008 04:50:13 +0000 (21:50 -0700)]
ASoC: Add support for Gumstix Overo
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Steve Sakoman [Fri, 31 Oct 2008 04:35:26 +0000 (21:35 -0700)]
ASoC: Add support for TWL4030 audio codec
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Rothwell [Fri, 31 Oct 2008 03:41:06 +0000 (14:41 +1100)]
ALSA: ASoC - restore removed variable declaration
sound/soc/soc-dapm.c: In function 'snd_soc_dapm_sys_add':
sound/soc/soc-dapm.c:828: error: 'ret' undeclared (first use in this function)
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Thu, 30 Oct 2008 16:53:19 +0000 (17:53 +0100)]
ALSA: ASoC - Fix a typo in Kconfig
The last change to Kconfig
ca53fb24dd21bff32c4b41b2be1035a1adfc0135
added a wrong item SND_SOC_AC97, which must be SND_SOC_AC97_CODEC.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Timur Tabi [Thu, 7 Aug 2008 16:22:32 +0000 (11:22 -0500)]
ASoC: Disable automatic volume control in the CS4270 sound driver
Disable the automatic volume control feature of the CS4270 audio codec. This
feature, which is enabled by default, causes volume change commands to be
delayed. Sometimes the volume change happens after playback is started.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 22 Oct 2008 21:41:11 +0000 (22:41 +0100)]
ASoC: Use finer grained dependencies in SND_SOC_ALL_CODECS
Move the bus dependencies in SND_SOC_ALL_CODECS into the individual
codec options rather than have them centrally. This allows the
inclusion of AC97 codecs when testing on platforms with AC97 support
and will also handle codecs on multi-function devices more gracefully.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 28 Oct 2008 15:04:35 +0000 (15:04 +0000)]
ASoC: Do a warm reset after cold when resetting the WM9713
The WM9713 comes out of cold reset in low power mode so always requires
a warm reset to bring up the AC97 link after a cold reset.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 30 Jul 2008 18:12:04 +0000 (19:12 +0100)]
ASoC: Add PXA SSP support
The SSP ports PXA series processors can be used to implement a variety of
audio interface formats. This patch implements support for I2S, DSP A and
DSP B modes on these ports.
This patch is based on the previous out of tree pxa2xx-ssp driver (which
was originally written by Liam Girdwood with updates from Philipp Zabel
and Nicola Perrino) and pxa3xx-ssp driver (originally written by Seth
Forsee based on the pxa2xx-ssp driver). Testing coverage is not complete
currently.
Tested-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 28 Oct 2008 13:02:31 +0000 (13:02 +0000)]
ASoC: Remove DAPM restriction on mixer control name lengths
As well as ensuring that UI-relevant parts of control names don't get
truncated in the DAPM code this avoids conflicts in long control names
that differ only at the end of a long string.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 21 Oct 2008 20:45:08 +0000 (21:45 +0100)]
ASoC: Convert core to use standard debug print macros
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 14 Oct 2008 12:58:36 +0000 (13:58 +0100)]
ASoC: Fix handling of DAPM suspend work
Since we can query the playback stream power state directly we do not
need to infer if it is powered up from the timer being scheduled. Doing
this avoids problems that previously existed with streams being
incorrectly determined to be powered up caused when the timer is
scheduled when streams are closed after being partially set up.
Reported-by: Nobin Mathew <nobin.mathew@gmail.com>
Reported-by: Jukka Hynninen <ext-jukka.hynninen@vaisala.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Troy Kisky [Tue, 14 Oct 2008 00:42:14 +0000 (17:42 -0700)]
ASoC: Allow setting codec register with debugfs filesystem
i.e. echo 6 59 >/sys/kernel/debug/soc-audio.0/codec_reg
will set register 0x06 to a value of 0x59.
Also, pop_time debugfs interface setup is moved so that it
is setup in the same function as codec_reg
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 30 Oct 2008 12:37:10 +0000 (12:37 +0000)]
ALSA: ASoC: Fix WM9713 ALC Decay Time name
The control had an extra space at the end of the name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jon Smirl [Thu, 30 Oct 2008 12:37:09 +0000 (12:37 +0000)]
ALSA: ASoC: Fix some minor errors in mpc5200 psc i2s driver
Fix missing unsigned for irqsave flags in psc i2s driver
Make attribute visiblity static
Collect all sysfs errors before checking status
[Word wrapped DEVICE_ATTR() lines for 80 columns -- broonie]
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mark Brown [Thu, 30 Oct 2008 12:37:08 +0000 (12:37 +0000)]
ALSA: ASoC: Fix mono controls after conversion to support full int masks
When ASoC was converted to support full int width masks SOC_SINGLE_VALUE()
omitted the assignment of rshift, causing the control operatins to report
some mono controls as stereo. This happened to work some of the time due
to a confusion between shift and min in snd_soc_info_volsw().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Tue, 28 Oct 2008 10:41:18 +0000 (11:41 +0100)]
Merge branch 'topic/fix/asoc' into topic/asoc
Cliff Cai [Mon, 27 Oct 2008 09:09:25 +0000 (17:09 +0800)]
ALSA: ASoC: Blackfin: update SPORT0 port selector (v2)
- Setting the TFS pin selector for SPORT 0 based on whether the selected
port id F or G. If the port is F then no conflict should exist for the
TFS. When Port G is selected and EMAC then there is a conflict between
the PHY interrupt line and TFS. Current settings prevent the conflict
by ignoring the TFS pin when Port G is selected. This allows both
ssm2602 using Port G and EMAC concurrently.
- some code cleanup
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 27 Oct 2008 07:37:08 +0000 (08:37 +0100)]
Merge branch 'topic/asoc-next' into topic/asoc
Linus Torvalds [Sun, 26 Oct 2008 19:13:29 +0000 (12:13 -0700)]
Linux 2.6.28-rc2
.. fix all the worst problems in -rc1
Geert Uytterhoeven [Sun, 26 Oct 2008 18:51:14 +0000 (19:51 +0100)]
m68k: Disable Amiga serial console support if modular
If CONFIG_AMIGA_BUILTIN_SERIAL=m, I get the following warnings:
| drivers/char/amiserial.c: At top level:
| drivers/char/amiserial.c:2138: warning: data definition has no type or storage class
| drivers/char/amiserial.c:2138: warning: type defaults to 'int' in declaration of 'console_initcall'
| drivers/char/amiserial.c:2138: warning: parameter names (without types) in function declaration
| drivers/char/amiserial.c:2134: warning: 'amiserial_console_init' defined but not used
because console_initcall() is not defined (nor really sensible) in the
modular case.
So disable serial console support if the driver is modular.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Davide Libenzi [Fri, 17 Oct 2008 23:17:40 +0000 (16:17 -0700)]
epoll: avoid double-inserts in case of EFAULT
In commit
f337b9c58332bdecde965b436e47ea4c94d30da0 ("epoll: drop
unnecessary test") Thomas found that there is an unnecessary (always
true) test in ep_send_events(). The callback never inserts into
->rdllink while the send loop is performed, and also does the
~EP_PRIVATE_BITS test. Given we're holding the mutex during this time,
the conditions tested inside the loop are always true.
HOWEVER.
The test "!ep_is_linked(&epi->rdllink)" wasn't there because we insert
into ->rdllink, but because the send-events loop might terminate before
the whole list is scanned (-EFAULT).
In such cases, when the loop terminates early, and when a (leftover)
file received an event while we're performing the lockless loop, we need
such test to avoid to double insert the epoll items. The list_splice()
done a few steps below, will correctly re-insert the ones that were left
on "txlist".
This should fix the kenrel.org bugzilla entry 11831.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arjan van de Ven [Sat, 25 Oct 2008 19:41:41 +0000 (12:41 -0700)]
select: deal with math overflow from borderline valid userland data
Some userland apps seem to pass in a "0" for the seconds, and several
seconds worth of usecs to select(). The old kernels accepted this just
fine, so the new kernels must too.
However, due to the upscaling of the microseconds to nanoseconds we had
some cases where we got math overflow, and depending on the GCC version
(due to inlining decisions) that actually resulted in an -EINVAL return.
This patch fixes this by adding the excess microseconds to the seconds
field.
Also with thanks to Marcin Slusarz for spotting some implementation bugs
in the diagnostics patches.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arjan van de Ven [Sun, 26 Oct 2008 17:25:30 +0000 (10:25 -0700)]
wireless: fix regression caused by regulatory config option
The default for the regulatory compatibility option is wrong;
if you picked the default you ended up with a non-functional wifi
system (at least I did on Fedora 9 with iwl4965).
I don't think even the October 2008 releases of the various distros
has the new userland so clearly the default is wrong, and also
we can't just go about deleting this in 2.6.29...
Change the default to "y" and also adjust the config text a little to
reflect this.
This patch fixes regression #11859
With thanks to Johannes Berg for the diagnostics
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen Rothwell [Tue, 21 Oct 2008 05:11:20 +0000 (16:11 +1100)]
cgroup: remove unused variable
/scratch/sfr/next/kernel/cgroup.c: In function 'cgroup_tasks_start':
/scratch/sfr/next/kernel/cgroup.c:2107: warning: unused variable 'i'
Introduced in commit
cc31edceee04a7b87f2be48f9489ebb72d264844 "cgroups:
convert tasks file to use a seq_file with shared pid array".
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 26 Oct 2008 16:36:19 +0000 (09:36 -0700)]
Merge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (abituguru3) enable DMI probing feature on AW9D-MAX
hwmon: (abituguru3) Cosmetic whitespace fixes
hwmon: (adt7473) Fix voltage conversion routines
hwmon: (lm90) Add support for the LM99 16 degree offset
hwmon: (lm90) Fix handling of hysteresis value
hwmon-vid: Add support for AMD family 10h CPUs
hwmon: (w83781d) Fix linking when built-in
Francois Romieu [Sun, 26 Oct 2008 16:02:49 +0000 (17:02 +0100)]
r8169: revert "read MAC address from EEPROM on init"
This reverts commit
7bf6bf4803df1adc927f585168d2135fb019c698.
The code has both a short existence and an increasing track of failures
despite some work to amend it for -rc1. It is not just a matter of
reading the eeprom: sometimes the eeprom is read correctly, then the mac
address is not written correctly back into the mac registers.
Some chipsets seem to work reliably but it is not clear at this point if
the code can simply be made to work on a per-chipset basis and post -rc1
is not the place where I want to experiment these things.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sun, 26 Oct 2008 05:40:26 +0000 (05:40 +0000)]
arm ide breakage
a) semicolon before the function body is a bad idea
b) it's const struct foo, not struct const foo
c) incidentally, it's ecard_remove_driver(), not ecard_unregister_driver()
d) compiling is occasionally useful.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sun, 26 Oct 2008 05:12:34 +0000 (05:12 +0000)]
fix allmodconfig breakage
If you use KCONFIG_ALLCONFIG (even with empty file) you get broken
allmodconfig/allyesconfig; CONFIG_MODULES gets turned off, with obvious
massive fallout.
Breakage had been introduced when conf_set_all_new_symbols() got used
for allmodconfig et.al.
What happens is that sym_calc_value(modules_sym) done in
conf_read_simple() sets SYMBOL_VALID on both modules_sym and MODULES.
When we get to conf_set_all_new_symbols(), we set sym->def[S_DEF_USER]
on everything, but it has no effect on sym->curr for the symbols that
already have SYMBOL_VALID - these are stuck.
Solution: use sym_clear_all_valid() in there. Note that it makes
reevaluation of modules_sym redundant - sym_clear_all_valid() will do
that itself.
[ Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11512, says Alexey ]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alistair John Strachan [Sun, 26 Oct 2008 16:04:40 +0000 (17:04 +0100)]
hwmon: (abituguru3) enable DMI probing feature on AW9D-MAX
Switch the AW9D-MAX over from port probing to the preferred DMI
probe method.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Alistair John Strachan [Sun, 26 Oct 2008 16:04:40 +0000 (17:04 +0100)]
hwmon: (abituguru3) Cosmetic whitespace fixes
As the probable result of zealous copy/pasting, many supported boards
contain sensor names with trailing whitespace. Though this is not a
huge problem, it is inconsistent with other sensor names, and with
other similar hwmon drivers.
Additionally, the DMI nag message added in 2.6.27 was missing a
space between two sentence fragments -- might as well clean that up
too.
Doesn't alter any kernel text, just data.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Sun, 26 Oct 2008 16:04:40 +0000 (17:04 +0100)]
hwmon: (adt7473) Fix voltage conversion routines
Fix voltage conversion routines. Based on an earlier patch from
Paulius Zaleckas.
According to the datasheet voltage is scaled with resistors and
value 192 is nominal voltage. 0 is 0V.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Jean Delvare [Sun, 26 Oct 2008 16:04:39 +0000 (17:04 +0100)]
hwmon: (lm90) Add support for the LM99 16 degree offset
The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Jean Delvare [Sun, 26 Oct 2008 16:04:39 +0000 (17:04 +0100)]
hwmon: (lm90) Fix handling of hysteresis value
There are several problems in the way the hysteresis value is handled
by the lm90 driver:
* In show_temphyst(), specific handling of the MAX6646 is missing, so
the hysteresis is reported incorrectly if the critical temperature
is over 127 degrees C.
* In set_temphyst(), the new hysteresis register value is written to
the chip but data->temp_hyst isn't updated accordingly, so there is
a short period of time (up to 2 seconds) where the old hystereris
value will be returned while the new one is already active.
* In set_temphyst(), the critical temperature which is used as a base
to compute the value of the hysteresis register lacks
device-specific handling. As a result, the value of the hysteresis
register might be incorrect for the ADT7461 and MAX6646 chips.
Fix these 3 bugs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Nate Case <ncase@xes-inc.com>
Jean Delvare [Sun, 26 Oct 2008 16:04:39 +0000 (17:04 +0100)]
hwmon-vid: Add support for AMD family 10h CPUs
The AMD family 10h CPUs use the same VID decoding table as the family
0Fh CPUs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Geert Uytterhoeven [Sun, 26 Oct 2008 16:04:38 +0000 (17:04 +0100)]
hwmon: (w83781d) Fix linking when built-in
When w83781d is built-in, the final links fails with the following vague error
message:
`.exit.text' referenced in section `.init.text' of drivers/built-in.o: defined
in discarded section `.exit.text' of drivers/built-in.o
w83781d_isa_unregister() cannot be marked __exit, as it's also called from
sensors_w83781d_init(), which is marked __init.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Linus Torvalds [Sun, 26 Oct 2008 02:57:30 +0000 (19:57 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: Fix duplicate entries returned from getdents() system call
ext3: Fix duplicate entries returned from getdents() system call
Linus Torvalds [Sun, 26 Oct 2008 02:53:38 +0000 (19:53 -0700)]
Revert "Call init_workqueues before pre smp initcalls."
This reverts commit
a802dd0eb5fc97a50cf1abb1f788a8f6cc5db635 by moving
the call to init_workqueues() back where it belongs - after SMP has been
initialized.
It also moves stop_machine_init() - which needs workqueues - to a later
phase using a core_initcall() instead of early_initcall(). That should
satisfy all ordering requirements, and was apparently the reason why
init_workqueues() was moved to be too early.
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Theodore Ts'o [Sat, 25 Oct 2008 15:39:08 +0000 (11:39 -0400)]
ext4: Fix duplicate entries returned from getdents() system call
Fix a regression caused by commit
d0156417, "ext4: fix ext4_dx_readdir
hash collision handling", where deleting files in a large directory
(requiring more than one getdents system call), results in some
filenames being returned twice. This was caused by a failure to
update info->curr_hash and info->curr_minor_hash, so that if the
directory had gotten modified since the last getdents() system call
(as would be the case if the user is running "rm -r" or "git clean"),
a directory entry would get returned twice to the userspace.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch fixes the bug reported by Markus Trippelsdorf at:
http://bugzilla.kernel.org/show_bug.cgi?id=11844
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Theodore Ts'o [Sat, 25 Oct 2008 15:38:37 +0000 (11:38 -0400)]
ext3: Fix duplicate entries returned from getdents() system call
Fix a regression caused by commit
6a897cf4, "ext3: fix ext3_dx_readdir
hash collision handling", where deleting files in a large directory
(requiring more than one getdents system call), results in some
filenames being returned twice. This was caused by a failure to
update info->curr_hash and info->curr_minor_hash, so that if the
directory had gotten modified since the last getdents() system call
(as would be the case if the user is running "rm -r" or "git clean"),
a directory entry would get returned twice to the userspace.
This patch fixes the bug reported by Markus Trippelsdorf at:
http://bugzilla.kernel.org/show_bug.cgi?id=11844
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Jens Axboe [Fri, 24 Oct 2008 07:22:42 +0000 (09:22 +0200)]
libata: fix bug with non-ncq devices
The recent commit
2fca5ccf97d2c28bcfce44f5b07d85e74e3cd18e ("libata:
switch to using block layer tagging support") to enable support for
block layer tagging in libata was broken for non-NCQ devices
The block layer initializes the tag field to -1 to detect invalid uses
of a tag, and if the libata devices does NOT support NCQ, we just used
that field to index the internal command list. So we need to check for
-1 first and only use the tag field if it's valid.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 24 Oct 2008 03:06:52 +0000 (20:06 -0700)]
Linux 2.6.28-rc1
Randy Dunlap [Fri, 24 Oct 2008 01:14:55 +0000 (18:14 -0700)]
Fix PCI hotplug printk format
Fix printk format warning:
drivers/pci/hotplug/acpiphp_ibm.c:207: warning: format '%08lx' expects type 'long unsigned int', but argument 3 has type 'long long unsigned int'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 24 Oct 2008 02:31:34 +0000 (19:31 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: remove unused resource assignment in pci_read_bridge_bases()
PCI hotplug: shpchp: message refinement
PCI hotplug: shpchp: replace printk with dev_printk
PCI: add routines for debugging and handling lost interrupts
PCI hotplug: pciehp: message refinement
PCI: fix ARI code to be compatible with mixed ARI/non-ARI systems
PCI hotplug: cpqphp: fix kernel NULL pointer dereference
Linus Torvalds [Fri, 24 Oct 2008 02:19:54 +0000 (19:19 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
tcp: Restore ordering of TCP options for the sake of inter-operability
net: Fix disjunct computation of netdev features
sctp: Fix to handle SHUTDOWN in SHUTDOWN_RECEIVED state
sctp: Fix to handle SHUTDOWN in SHUTDOWN-PENDING state
sctp: Add check for the TSN field of the SHUTDOWN chunk
sctp: Drop ICMP packet too big message with MTU larger than current PMTU
p54: enable 2.4/5GHz spectrum by eeprom bits.
orinoco: reduce stack usage in firmware download path
ath5k: fix suspend-related oops on rmmod
[netdrvr] fec_mpc52xx: Implement polling, to make netconsole work.
qlge: Fix MSI/legacy single interrupt bug.
smc911x: Make the driver safer on SMP
smc911x: Add IRQ polarity configuration
smc911x: Allow Kconfig dependency on ARM
sis190: add identifier for Atheros AR8021 PHY
8139x: reduce message severity on driver overlap
igb: add IGB_DCA instead of selecting INTEL_IOATDMA
igb: fix tx data corruption with transition to L0s on 82575
ehea: Fix memory hotplug support
netdev: DM9000: remove BLACKFIN hacking in DM9000 netdev driver
...
Linus Torvalds [Fri, 24 Oct 2008 02:19:14 +0000 (19:19 -0700)]
Merge git://git./linux/kernel/git/davem/sparc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
math-emu: Fix thinko in _FP_DIV
math-emu: Fix signalling of underflow and inexact while packing result.
sparc: Add checkstack support
sparc: correct section of current_pc()
sparc: correct section of apc_no_idle
sparc64: Fix race in arch/sparc64/kernel/trampoline.S
Zhao, Yu [Mon, 13 Oct 2008 13:02:27 +0000 (21:02 +0800)]
PCI: remove unused resource assignment in pci_read_bridge_bases()
This cleanup removes the resource assignment in pci_read_bridge_bases()
since it has taken care by pci_alloc_child_bus() when allocating the bus:
/* Set up default resource pointers and names.. */
for (i = 0; i < PCI_BRIDGE_RES_NUM; i++) {
child->resource[i] = &bridge->resource[PCI_BRIDGE_RESOURCES+i];
child->resource[i]->name = child->name;
}
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Taku Izumi [Thu, 23 Oct 2008 02:54:39 +0000 (11:54 +0900)]
PCI hotplug: shpchp: message refinement
This patch refines messages in shpchp module. The main changes are as
follows:
- remove the trailing "."
- remove __func__ as much as possible
- capitalize the first letter of messages
- show PCI device address including its domain
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Taku Izumi [Thu, 23 Oct 2008 02:52:12 +0000 (11:52 +0900)]
PCI hotplug: shpchp: replace printk with dev_printk
This patch replaces printks within shpchp module with dev_printks.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Linus Torvalds [Thu, 23 Oct 2008 23:08:11 +0000 (16:08 -0700)]
Merge git://git./linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: drivers/ide/generic.c -> drivers/ide/ide-pci-generic.c
ide-disk: set non-rotational queue flag for SSD and CF devices
ide-cd: add TEAC CD-224E to the NO_AUTOCLOSE list
ide: Add tx4938ide driver (v2)
TXx9: Add TX4938 ATA support (v3)
ide: Add tx4939ide driver (v6)
ide: two more pci_ioremap_bar() conversions
pci: use pci_ioremap_bar() in drivers/ide
sgiioc4: use ide_host_add() (take 2)
sgiioc4: fix error cleanup path (take 2)
Linus Torvalds [Thu, 23 Oct 2008 23:07:32 +0000 (16:07 -0700)]
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds/acpi: Fix merge fallout from acpi_driver_data change
leds: Simplify logic in leds-ams-delta
leds: Fix trigger registration race
leds: Fix leds-class.c comment
leds: Add driver for HP harddisk protection LEDs
leds: leds-pca955x - Mark pca955x_led_set() static
leds: Remove uneeded leds-cm-x270 driver
leds: Remove uneeded strlen calls
leds: Add leds-wrap default-trigger
leds: Make default trigger fields const
leds: Add backlight LED trigger
leds: da903x: Add support for LEDs found on DA9030/DA9034
Linus Torvalds [Thu, 23 Oct 2008 23:06:49 +0000 (16:06 -0700)]
Merge branch 'for-linus' of /home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: corgi backlight driver should not select ssp drivers
[ARM] 5321/1: Kirkwood: fix typo in Makefile
[ARM] 5320/1: fix assembly constraints in implementation of do_div()
[ARM] 5318/1: Swap the PRRR and NMRR values in proc-v7.S
[ARM] 5316/1: AT91: oops (regression) fix on gpio irq
[ARM] msm: vreg interface to msm7k pmic
[ARM] msm: dma: various basic dma improvements and bugfixes
[ARM] msm: clock: provide clk_*() api support for
[ARM] msm: clean up iomap and devices
[ARM] msm: add proc_comm support, necessary for clock and power control
[ARM] msm: rename ARCH_MSM7X00A to ARCH_MSM
[ARM] pxa/spitz: fix unbalance parenthesis in header file spitz.h
[ARM] pxa: update {corgi,spitz}_defconfig to favor SPI-based drivers
[ARM] pxa: fix the corgi_ssp.c dependency issue in {corgi,spitz}_defconfig
Revert "[ARM] pxa/corgi: remove now unused corgi_ssp.c and corgi_lcd.c"
Linus Torvalds [Thu, 23 Oct 2008 23:05:59 +0000 (16:05 -0700)]
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Add driver for Tabletkiosk Sahara TouchIT-213 Tablet PC
backlight: da903x: Add backlight driver for DA9030/DA9034
tosa: add support for bl/lcd driver
backlight: add support for Sharp SL-6000 LCD and backlight drivers
Jens Axboe [Wed, 22 Oct 2008 07:34:49 +0000 (09:34 +0200)]
libata: switch to using block layer tagging support
libata currently has a pretty dumb ATA_MAX_QUEUE loop for finding
a free tag to use. Instead of fixing that up, convert libata to
using block layer tagging - gets rid of code in libata, and is also
much faster.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
James Bottomley [Sun, 3 Aug 2008 18:02:12 +0000 (13:02 -0500)]
PCI: add routines for debugging and handling lost interrupts
We're getting a lot of storage drivers blamed for interrupt misrouting
issues. This patch provides a standard way of reporting the problem
... and, if possible, correcting it.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Taku Izumi [Thu, 23 Oct 2008 02:47:32 +0000 (11:47 +0900)]
PCI hotplug: pciehp: message refinement
This patch refines messages in pciehp module. The main changes are as
follows:
- remove the trailing "."
- remove __func__ as much as possible
- capitalize the first letter of messages
- show PCI device address including its domain
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Zhao, Yu [Thu, 23 Oct 2008 05:15:39 +0000 (13:15 +0800)]
PCI: fix ARI code to be compatible with mixed ARI/non-ARI systems
The original ARI support code has a compatibility problem with non-ARI
devices. If a device doesn't support ARI, turning on ARI forwarding on
its upper level bridge will cause undefined behavior.
This fix turns on ARI forwarding only when the subordinate devices
support it.
Tested-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Kenji Kaneshige [Fri, 17 Oct 2008 00:23:51 +0000 (09:23 +0900)]
PCI hotplug: cpqphp: fix kernel NULL pointer dereference
The following patch fixes the regression in 2.6.27 that causes kernel
NULL pointer dereference at cpqphp driver probe time. This patch should
be backported to the .27 stable series.
Seems to have been introduced by
f46753c5e354b857b20ab8e0fe7b2579831dc369.
The root cause of this problem seems that cpqphp driver calls
pci_hp_register() wrongly. In current implementation, cpqphp driver
passes 'ctrl->pci_dev->subordinate' as a second parameter for
pci_hp_register(). But because hotplug slots and it's hotplug controller
(exists as a pci funcion) are on the same bus, it should be
'ctrl->pci_dev->bus' instead.
Cc: <stable@kernel.org>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stephen Rothwell [Thu, 23 Oct 2008 21:35:19 +0000 (22:35 +0100)]
leds/acpi: Fix merge fallout from acpi_driver_data change
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Bartlomiej Zolnierkiewicz [Thu, 23 Oct 2008 21:24:20 +0000 (23:24 +0200)]
ide: drivers/ide/generic.c -> drivers/ide/ide-pci-generic.c
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Thu, 23 Oct 2008 21:22:09 +0000 (23:22 +0200)]
ide-disk: set non-rotational queue flag for SSD and CF devices
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Márton Németh [Thu, 23 Oct 2008 21:22:09 +0000 (23:22 +0200)]
ide-cd: add TEAC CD-224E to the NO_AUTOCLOSE list
The "TEAC CD-ROM CD-224E" cannot close its tray, so add it to the NO_AUTOCLOSE
list. This will correct the "Can close tray" field of /proc/sys/dev/cdrom/info.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
[bart: minor fixups to patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Atsushi Nemoto [Thu, 23 Oct 2008 21:22:08 +0000 (23:22 +0200)]
ide: Add tx4938ide driver (v2)
This is the driver for the Toshiba TX4938 SoC EBUS controller ATA mode.
It has custom set_pio_mode and some hacks for big endian.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: ralf@linux-mips.org
Cc: sshtylyov@ru.mvista.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Atsushi Nemoto [Thu, 23 Oct 2008 21:22:08 +0000 (23:22 +0200)]
TXx9: Add TX4938 ATA support (v3)
Add a helper routine to register tx4938ide driver and use it on
RBTX4938 board.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Atsushi Nemoto [Thu, 23 Oct 2008 21:22:07 +0000 (23:22 +0200)]
ide: Add tx4939ide driver (v6)
This is the driver for the Toshiba TX4939 SoC ATA controller.
This controller has standard ATA taskfile registers and DMA
command/status registers, but the register layout is swapped on big
endian. There are some other endian issue and some special registers
which requires many custom dma_ops/tp_ops routines and build_dmatable.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: ralf@linux-mips.org
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Arjan van de Ven [Thu, 23 Oct 2008 21:22:07 +0000 (23:22 +0200)]
ide: two more pci_ioremap_bar() conversions
based on suggestion from Sergei Shtylyov, there are two more places
where using pci_ioremap_bar() makes sense.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Arjan van de Ven [Thu, 23 Oct 2008 21:22:07 +0000 (23:22 +0200)]
pci: use pci_ioremap_bar() in drivers/ide
Use the newly introduced pci_ioremap_bar() function in drivers/ide.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Thu, 23 Oct 2008 21:22:06 +0000 (23:22 +0200)]
sgiioc4: use ide_host_add() (take 2)
Convert the driver to use ide_host_add() -- this seems to be a straightforward
change which I'm not sure why hasn't been done yet...
While doing this at last, get rid of:
- useless local copy of the 'sgiioc4_port_info' variable;
- unnecessary 'goto' and label...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: jeremy@sgi.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Thu, 23 Oct 2008 21:22:06 +0000 (23:22 +0200)]
sgiioc4: fix error cleanup path (take 2)
The driver "forgot" to call iounmap() iff request_mem_region() call failed in
sgiioc4_ide_setup_pci_device()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: jeremy@sgi.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Russell King [Thu, 23 Oct 2008 21:06:53 +0000 (22:06 +0100)]
[ARM] pxa: corgi backlight driver should not select ssp drivers
Resolves build errors with eseries and magician defconfigs (which
make use of the corgi backlight driver.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ilpo Järvinen [Thu, 23 Oct 2008 21:06:35 +0000 (14:06 -0700)]
tcp: Restore ordering of TCP options for the sake of inter-operability
This is not our bug! Sadly some devices cannot cope with the change
of TCP option ordering which was a result of the recent rewrite of
the option code (not that there was some particular reason steming
from the rewrite for the reordering) though any ordering of TCP
options is perfectly legal. Thus we restore the original ordering
to allow interoperability with/through such broken devices and add
some warning about this trap. Since the reordering just happened
without any particular reason, this change shouldn't cost us
anything.
There are already couple of known failure reports (within close
proximity of the last release), so the problem might be more
wide-spread than a single device. And other reports which may
be due to the same problem though the symptoms were less obvious.
Analysis of one of the case revealed (with very high probability)
that sack capability cannot be negotiated as the first option
(SYN never got a response).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Reported-by: Aldo Maggi <sentiniate@tiscali.it>
Tested-by: Aldo Maggi <sentiniate@tiscali.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 23 Oct 2008 20:02:48 +0000 (13:02 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
staging: pcc_acpi: delete obsolete driver
Linus Torvalds [Thu, 23 Oct 2008 20:02:03 +0000 (13:02 -0700)]
Merge git://git./linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (21 commits)
[SCSI] sd: fix computation of the full size of the device
[SCSI] lib: string_get_size(): don't hang on zero; no decimals on exact
[SCSI] sun3x_esp: Convert && to ||
[SCSI] sd: remove command-size switching code
[SCSI] 3w-9xxx: remove unnecessary local_irq_save/restore for scsi sg copy API
[SCSI] 3w-xxxx: remove unnecessary local_irq_save/restore for scsi sg copy API
[SCSI] fix netlink kernel-doc
[SCSI] sd: Fix handling of NO_SENSE check condition
[SCSI] export busy state via q->lld_busy_fn()
[SCSI] refactor sdev/starget/shost busy checking
[SCSI] mptfusion: Increase scsi-timeouts, similariy to the LSI 4.x driver.
[SCSI] aic7xxx: Take the LED out of diagnostic mode on PM resume
[SCSI] aic79xx: user visible misuse wrong SI units (not disk size!)
[SCSI] ipr: use memory_read_from_buffer()
[SCSI] aic79xx: fix shadowed variables
[SCSI] aic79xx: fix shadowed variables, add statics
[SCSI] aic7xxx: update *_shipped files
[SCSI] aic7xxx: update .reg files
[SCSI] aic7xxx: introduce "dont_generate_debug_code" keyword in aicasm parser
[SCSI] scsi_dh: Initialize path state to be passive when path is not owned
...
Linus Torvalds [Thu, 23 Oct 2008 19:38:39 +0000 (12:38 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix section mismatch warning - apic_x2apic_phys
x86: fix section mismatch warning - apic_x2apic_cluster
x86: fix section mismatch warning - apic_x2apic_uv_x
x86: fix section mismatch warning - apic_physflat
x86: fix section mismatch warning - apic_flat
x86: memtest fix use of reserve_early()
x86 syscall.h: fix argument order
x86/tlb_uv: remove strange mc146818rtc include
x86: remove redundant KERN_DEBUG on pr_debug
x86: do_boot_cpu - check if we have ESR register
x86: MAINTAINERS change for AMD microcode patch loader
x86/proc: fix /proc/cpuinfo cpu offline bug
x86: call dmi-quirks for HP Laptops after early-quirks are executed
x86, kexec: fix hang on i386 when panic occurs while console_sem is held
MCE: Don't run 32bit machine checks with interrupts on
x86: SB600: skip IRQ0 override if it is not routed to INT2 of IOAPIC
x86: make variables static
Len Brown [Thu, 23 Oct 2008 19:14:52 +0000 (15:14 -0400)]
staging: pcc_acpi: delete obsolete driver
pcc_acpi is based on an old version
of drivers/misc/panasonic-laptop.c
Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Thu, 23 Oct 2008 19:07:17 +0000 (12:07 -0700)]
Fix compile warning in kernel/params.c
Move free_module_param_attrs() into the CONFIG_MODULES section, since
it's only used inside there. Thus avoiding the warning
kernel/params.c:514: warning: 'free_module_param_attrs' defined but not used
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 23 Oct 2008 19:04:37 +0000 (12:04 -0700)]
Merge branch 'proc' of git://git./linux/kernel/git/adobriyan/proc
* 'proc' of git://git.kernel.org/pub/scm/linux/kernel/git/adobriyan/proc: (35 commits)
proc: remove fs/proc/proc_misc.c
proc: move /proc/vmcore creation to fs/proc/vmcore.c
proc: move pagecount stuff to fs/proc/page.c
proc: move all /proc/kcore stuff to fs/proc/kcore.c
proc: move /proc/schedstat boilerplate to kernel/sched_stats.h
proc: move /proc/modules boilerplate to kernel/module.c
proc: move /proc/diskstats boilerplate to block/genhd.c
proc: move /proc/zoneinfo boilerplate to mm/vmstat.c
proc: move /proc/vmstat boilerplate to mm/vmstat.c
proc: move /proc/pagetypeinfo boilerplate to mm/vmstat.c
proc: move /proc/buddyinfo boilerplate to mm/vmstat.c
proc: move /proc/vmallocinfo to mm/vmalloc.c
proc: move /proc/slabinfo boilerplate to mm/slub.c, mm/slab.c
proc: move /proc/slab_allocators boilerplate to mm/slab.c
proc: move /proc/interrupts boilerplate code to fs/proc/interrupts.c
proc: move /proc/stat to fs/proc/stat.c
proc: move rest of /proc/partitions code to block/genhd.c
proc: move /proc/cpuinfo code to fs/proc/cpuinfo.c
proc: move /proc/devices code to fs/proc/devices.c
proc: move rest of /proc/locks to fs/locks.c
...