OSDN Git Service
David S. Miller [Thu, 22 Aug 2013 23:04:41 +0000 (16:04 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
1) Some constifications, from Mathias Krause.
2) Catch bugs if a hold timer is still active when xfrm_policy_destroy()
is called, from Fan Du.
3) Remove a redundant address family checking, from Fan Du.
4) Make xfrm_state timer monotonic to be independent of system clock changes,
from Fan Du.
5) Remove an outdated comment on returning -EREMOTE in the xfrm_lookup(),
from Rami Rosen.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Thu, 22 Aug 2013 01:57:20 +0000 (10:57 +0900)]
ethernet: broadcom: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Thu, 22 Aug 2013 01:55:21 +0000 (10:55 +0900)]
ethernet: moxa: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Thu, 22 Aug 2013 00:29:23 +0000 (17:29 -0700)]
tcp: increase throughput when reordering is high
The stack currently detects reordering and avoid spurious
retransmission very well. However the throughput is sub-optimal under
high reordering because cwnd is increased only if the data is deliverd
in order. I.e., FLAG_DATA_ACKED check in tcp_ack(). The more packet
are reordered the worse the throughput is.
Therefore when reordering is proven high, cwnd should advance whenever
the data is delivered regardless of its ordering. If reordering is low,
conservatively advance cwnd only on ordered deliveries in Open state,
and retain cwnd in Disordered state (RFC5681).
Using netperf on a qdisc setup of 20Mbps BW and random RTT from 45ms
to 55ms (for reordering effect). This change increases TCP throughput
by 20 - 25% to near bottleneck BW.
A special case is the stretched ACK with new SACK and/or ECE mark.
For example, a receiver may receive an out of order or ECN packet with
unacked data buffered because of LRO or delayed ACK. The principle on
such an ACK is to advance cwnd on the cummulative acked part first,
then reduce cwnd in tcp_fastretrans_alert().
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Wed, 21 Aug 2013 22:18:30 +0000 (02:18 +0400)]
SolutionEngine7724: fix typo in Ether platform data
Commit
bd61224b1cbec096694e89c4187119c8576fe186 (SolutionEngine7724: fix Ether
support) has a typo in the 'phy_interface' field name of the platform data which
causes build error -- fix it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Wed, 21 Aug 2013 22:17:25 +0000 (02:17 +0400)]
SH7619: fix typo in Ether platform data
Commit
06a64f91da72cb5827e2bedef2ead60a123fd66e (SH7619: fix Ether support) has
a typo in the 'phy_interface' field name of the platform data which causes build
error -- fix it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Wu [Wed, 21 Aug 2013 21:17:11 +0000 (23:17 +0200)]
r8169: fix invalid register dump
For some reason, my PCIe RTL8111E onboard NIC on a GA-Z68X-UD3H-B3
motherboard reads as FFs when reading from MMIO with a block size
larger than 7. Therefore change to reading blocks of four bytes.
Ben Hutchings noted that the buffer is large enough to hold all
registers, so now all registers are read.
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Aug 2013 20:00:46 +0000 (13:00 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to igb and e1000e.
Akeem provides 3 igb patches, the first resets the link when EEE is enabled
or disabled if the link is up. His second patch changes a register read
which normally stores of the read value to "just-read" so that hardware
can accurately latch the register read. Lastly, he adds rcu_lock to avoid
a possible race condition with igb_update_stats function.
Mitch provides a fix for SR-IOV, where MSI-X interrupts are required, so
make sure that MSI-X is enabled before allowing the user to turn on SR-IOV.
Alex's igb patch make it so that we limit the lower bound for max_frame_size
to the size of a standard Ethernet frame. This allows for feature parity
with other Intel based drivers such as ixgbe.
Carolyn adds a SKU for a flashless i210 device and a fix for get_fw_version()
so that it works for all parts for igb. In addition, she has 2 igb patches
to refactor NVM code to accommodate devices with no flash. Lastly, she
adds code to check for the failure of pci_disable_link_state() to attempt
to work around a problem found with some systems.
Laura provides the remaining 2 igb patches. One removing the hard-coded
value for the size of the RETA indirection table, and creates a macro instead
for the RETA indirection table. The second adds the ethtool callbacks
necessary to change the RETA indirection table from userspace.
Bruce fixes a whitespace issue in a recent commit and resolves a jiffies
comparison warning by using time_after().
Li provides a fix for e1000e to avoid a kernel crash on shutdown by adding
one more check in e1000e_shutdown(). This is due to e1000e_shutdown()
trying to clear correctable errors on the upstream P2P bridge, when under
some cases we do not have the upstream P2P bridge.
v2:
- fixed patch 11 conditional statement from < to <= based on feedback
from Ben Hutchings
- fixed patch 12 patch description (adding the commit summary) based
on feedback from Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Thu, 15 Aug 2013 03:43:24 +0000 (03:43 +0000)]
e1000e: resolve checkpatch JIFFIES_COMPARISON warning
WARNING:JIFFIES_COMPARISON: Comparing jiffies is almost always wrong;
prefer time_after, time_before and friends
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Li Zhang [Tue, 13 Aug 2013 18:42:58 +0000 (18:42 +0000)]
e1000e: Avoid kernel crash during shutdown
While doing shutdown on the PCI device, the corresponding callback
function e1000e_shutdown() is trying to clear those correctable
errors on the upstream P2P bridge. Unfortunately, we don't have
the upstream P2P bridge under some cases (e.g. PCI-passthrou for
KVM on Power). That leads to kernel crash eventually.
The patch adds one more check on that to avoid kernel crash.
Signed-off-by: Li Zhang <zhlcindy@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Sat, 3 Aug 2013 01:53:54 +0000 (01:53 +0000)]
e1000e: Add code to check for failure of pci_disable_link_state call
This patch attempts to work around a problem found with some systems where
the call to pci_diable_link_state_locked() fails. As a result, ASPM is not,
in fact, disabled. Changing disable ASPM code to check if state actually
is disabled after the call and, if not, try another way to disable it.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Fri, 2 Aug 2013 03:33:32 +0000 (03:33 +0000)]
e1000e: cleanup whitespace in recent commit
Commit (
c96ddb0b e1000e: Use marco instead of digit for defining
e1000_rx_desc_packet_split) moved a define from one file to another but
missed using proper indentation/whitespace.
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Laura Mihaela Vasilescu [Wed, 31 Jul 2013 20:19:54 +0000 (20:19 +0000)]
igb: Expose RSS indirection table for ethtool
This patch adds the ethtool callbacks necessary to change the RETA
indirection table from userspace.
In order to achieve this, we add the indirection table field (rss_indir_tbl)
in the board specific data structure (struct igb_adapter) to preserve the
values across hardware resets.
The indirection table must be initialized with default values in the
following cases:
* at module init time
* when the number of RX queues changes.
For this reason we add a new field (rss_indir_tbl_init) in igb_adapter
that keeps track of the number of RX queues. Whenever the number of RX
queues changes, the rss_indir_tbl is modified and initialized with default
values. The rss_indir_tbl_init is updated accordingly.
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Laura Mihaela Vasilescu <laura.vasilescu@rosedu.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Laura Mihaela Vasilescu [Wed, 31 Jul 2013 20:19:48 +0000 (20:19 +0000)]
igb: Add macro for size of RETA indirection table
RETA indirection table is used to assign the received data to a CPU
in order to maintain an efficient distribution of network receive
processing across multiple CPUs.
This patch removes the hard-coded value for the size of the indirection
table and defines a new macro.
Signed-off-by: Laura Mihaela Vasilescu <laura.vasilescu@rosedu.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Tue, 16 Jul 2013 19:25:33 +0000 (19:25 +0000)]
igb: Fix get_fw_version function for all parts
This patch fixes issues found with older parts and older NVM tools in the
display of the version in ethtool.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Tue, 16 Jul 2013 19:18:36 +0000 (19:18 +0000)]
igb: Add device support for flashless SKU of i210 device
This patch adds the specific device id support for versions of i210 that do
not have flash installed.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Wed, 17 Jul 2013 19:02:53 +0000 (19:02 +0000)]
igb: Refactor NVM read functions to accommodate devices with no flash
This patch refactors NVM read functions in order to accommodate i210 devices
that do not have a flash. Previously, this was not supported on i210
devices.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Tue, 16 Jul 2013 19:17:32 +0000 (19:17 +0000)]
igb: Refactor of init_nvm_params
This patch refactors the init_nvm_params functions for 82575 and adds a new
function for the i210/i211 devices in order to configure separately the NVM
functionality for the i210/i211 family.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Tue, 16 Jul 2013 00:20:34 +0000 (00:20 +0000)]
igb: Update MTU so that it is always at least a standard frame size
This change makes it so that we limit the lower bound for max_frame_size to
the size of a standard Ethernet frame. This allows for feature parity with
other Intel based drivers such as ixgbe.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch A Williams [Thu, 20 Jun 2013 06:03:36 +0000 (06:03 +0000)]
igb: don't allow SR-IOV without MSI-X
MSI-X interrupts are required for SR-IOV operation. Check to make sure
they're enabled before allowing the user to turn on VFs.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Akeem G Abodunrin [Thu, 27 Jun 2013 09:10:23 +0000 (09:10 +0000)]
igb: Added rcu_lock to avoid race
This patch adds rcu_lock to avoid possible race condition with igb_update_stats
function accessing the rings in free_ q_vector.
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Akeem G Abodunrin [Thu, 6 Jun 2013 01:31:09 +0000 (01:31 +0000)]
igb: Read register for latch_on without return value
This patch changes register read to "just-read" without returning a value
for hardware to accurately latch the register value.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Akeem G Abodunrin [Fri, 24 May 2013 07:20:57 +0000 (07:20 +0000)]
igb: Reset the link when EEE setting changed
This patch resets the link, if link is up - whenever users enable or disable EEE
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Libo Chen [Wed, 21 Aug 2013 10:15:15 +0000 (18:15 +0800)]
net: phy: mdio-octeon: use platform_set_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_set_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Wed, 21 Aug 2013 10:15:11 +0000 (18:15 +0800)]
net: irda: pxaficp_ir: use platform_set_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using deva_set_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Aug 2013 03:46:16 +0000 (20:46 -0700)]
Merge branch 'for-davem' of git://gitorious.org/linux-can/linux-can-next
Marc Kleine-Budde says:
====================
this pull-request for net-next consists of a series by Alexander
Shiyan, he cleans up the mcp251x driver. As the first patch touches
arch/arm/mach-pxa, it's acked by Haojian Zhuang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Giuseppe CAVALLARO [Wed, 21 Aug 2013 07:11:14 +0000 (09:11 +0200)]
stmmac: remove useless csum flag
This patch removes the no_csum_insertion private parameter that is not used anymore
and, also, the "likely" annotation from the condition that is not in a critical path.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Wed, 21 Aug 2013 07:02:45 +0000 (15:02 +0800)]
net: emac: remove unnecessary dev_set_drvdata()
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Wed, 21 Aug 2013 07:02:41 +0000 (15:02 +0800)]
net: davinci_mdio: remove unnecessary dev_set_drvdata()
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Wed, 21 Aug 2013 07:02:36 +0000 (15:02 +0800)]
net: xilinx_emaclite: remove unnecessary dev_set_drvdata()
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Wed, 21 Aug 2013 07:02:31 +0000 (15:02 +0800)]
net: sunhme: remove unnecessary dev_set_drvdata()
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Wed, 21 Aug 2013 07:02:27 +0000 (15:02 +0800)]
net: sunbmac: remove unnecessary dev_set_drvdata()
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Wed, 21 Aug 2013 07:02:22 +0000 (15:02 +0800)]
net: fec_mpc52xx_phy: remove unnecessary dev_set_drvdata()
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Wed, 21 Aug 2013 07:02:18 +0000 (15:02 +0800)]
net: ucc_geth: remove unnecessary dev_set_drvdata()
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Wed, 21 Aug 2013 07:02:13 +0000 (15:02 +0800)]
net: fsl_pq_mdio: remove unnecessary dev_set_drvdata()
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 21 Aug 2013 19:21:50 +0000 (12:21 -0700)]
Merge branch 'tuntap'
Pavel Emelyanov says:
====================
tun: Some bits required for tun's checkpoint-restore (v2)
After taking a closer look on tun checkpoint-restore I've found several
issues with the tun's API that make it impossible to dump and restore
the state of tun device and attached tun-files.
The proposed API changes are all about extending the existing ioctl-based
stuff. Patches fit today's net-next.
This v2 has David's comments about patch #1 fixed. All the rest is the same.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Wed, 21 Aug 2013 10:32:39 +0000 (14:32 +0400)]
tun: Get skfilter layout
The only thing we may have from tun device is the fprog, whic contains
the number of filter elements and a pointer to (user-space) memory
where the elements are. The program itself may not be available if the
device is persistent and detached.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Wed, 21 Aug 2013 10:32:21 +0000 (14:32 +0400)]
tun: Allow to skip filter on attach
There's a small problem with sk-filters on tun devices. Consider
an application doing this sequence of steps:
fd = open("/dev/net/tun");
ioctl(fd, TUNSETIFF, { .ifr_name = "tun0" });
ioctl(fd, TUNATTACHFILTER, &my_filter);
ioctl(fd, TUNSETPERSIST, 1);
close(fd);
At that point the tun0 will remain in the system and will keep in
mind that there should be a socket filter at address '&my_filter'.
If after that we do
fd = open("/dev/net/tun");
ioctl(fd, TUNSETIFF, { .ifr_name = "tun0" });
we most likely receive the -EFAULT error, since tun_attach() would
try to connect the filter back. But (!) if we provide a filter at
address &my_filter, then tun0 will be created and the "new" filter
would be attached, but application may not know about that.
This may create certain problems to anyone using tun-s, but it's
critical problem for c/r -- if we meet a persistent tun device
with a filter in mind, we will not be able to attach to it to dump
its state (flags, owner, address, vnethdr size, etc.).
The proposal is to allow to attach to tun device (with TUNSETIFF)
w/o attaching the filter to the tun-file's socket. After this
attach app may e.g clean the device by dropping the filter, it
doesn't want to have one, or (in case of c/r) get information
about the device with tun ioctls.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Wed, 21 Aug 2013 10:32:00 +0000 (14:32 +0400)]
tun: Report whether the queue is attached or not
Multiqueue tun devices allow to attach and detach from its queues
while keeping the interface itself set on file.
Knowing this is critical for the checkpoint part of criu project.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Wed, 21 Aug 2013 10:31:38 +0000 (14:31 +0400)]
tun: Add ability to create tun device with given index
Tun devices cannot be created with ifidex user wants, but it's
required by checkpoint-restore project.
Long time ago such ability was implemented for rtnl_ops-based
interface for creating links (
9c7dafbf net: Allow to create links
with given ifindex), but the only API for creating and managing
tuntap devices is ioctl-based and is evolving with adding new ones
(
cde8b15f tuntap: add ioctl to attach or detach a file form tuntap
device).
Following that trend, here's how a new ioctl that sets the ifindex
for device, that _will_ be created by TUNSETIFF ioctl looks like.
So those who want a tuntap device with the ifindex N, should open
the tun device, call ioctl(fd, TUNSETIFINDEX, &N), then call TUNSETIFF.
If the index N is busy, then the register_netdev will find this out
and the ioctl would be failed with -EBUSY.
If setifindex is not called, then it will be generated as before.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai [Wed, 21 Aug 2013 07:08:59 +0000 (10:08 +0300)]
net/mlx4_en: Reduce scope of local variables in mlx4_en_xmit
Some variables could have their scope reduced.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai [Wed, 21 Aug 2013 07:08:58 +0000 (10:08 +0300)]
net/mlx4_en: Fix handling of dma_map failure
Result of skb_frag_dma_map() and dma_map_single() wasn't checked.
Added a check and proper handling in case of failure.
Moved the mapping to the beginning of mlx4_en_xmit(), before updating
the ring data structure to make error handling easier.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai [Wed, 21 Aug 2013 07:08:57 +0000 (10:08 +0300)]
net/mlx4_en: Notify user when TX ring in error state
When hardware gets into error state, must notify user about it.
When QP in error state no traffic will be tx'ed from the attached
tx_ring.
Driver should know how to recover from this unexpected state. I will send later
on the recovery flow, but having the print shouldn't be delayed.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eugenia Emantayev [Wed, 21 Aug 2013 07:08:56 +0000 (10:08 +0300)]
net/mlx4_en: Disable global flow control when PFC enabled
Fix a bug when FC and PFC are enabled/disabled at the same time.
According to ConnectX-3 Programmer Manual these two features are mutial
exclusive. So make sure when enabling PFC to turn off global FC and
vise versa. Otherwise it hurts the performance.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai [Wed, 21 Aug 2013 07:08:55 +0000 (10:08 +0300)]
net/mlx4_en: Coding style cleanup in mlx4_en_dcbnl_ieee_setpfc()
Fix some coding style issues in this function.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Himanshu Madhani [Wed, 21 Aug 2013 15:24:14 +0000 (11:24 -0400)]
qlcnic: Update version to 5.3.48
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shahed Shaikh [Wed, 21 Aug 2013 15:24:13 +0000 (11:24 -0400)]
qlcnic: Implement ndo_get_phys_port_id for 82xx adapter
Each function driver instance uses the MAC address of the
lowest function belonging to that physical port as a unique
port identifier. This port identifier is read and cached in
driver during probe and provided to user space through
ndo_get_phys_port_id()
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Himanshu Madhani [Wed, 21 Aug 2013 15:24:12 +0000 (11:24 -0400)]
qlcnic: Enable diagnostic test for multiple Tx queues.
o Enable diagnostic test via ethtool and QConvergeConsole
application when Multiple Tx queues are enabled on 82xx
series adapters.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Himanshu Madhani [Wed, 21 Aug 2013 15:24:11 +0000 (11:24 -0400)]
qlcnic: Enable Tx queue changes using ethtool for 82xx Series adapter.
o using ethtool {set|get}_channel option, user can change number
of Tx queues for 82xx Series adapter.
o updated ethtool -S <ethX> option to display stats from each Tx queue.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Himanshu Madhani [Wed, 21 Aug 2013 15:24:10 +0000 (11:24 -0400)]
qlcnic: Multi Tx queue support for 82xx Series adapter.
o 82xx firmware allows support for multiple Tx queues. This
patch will enable multi Tx queue support for 82xx series
adapter. Max number of Tx queues supported will be 8.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Shiyan [Mon, 19 Aug 2013 11:39:21 +0000 (15:39 +0400)]
can: mcp251x: Allow tuning SPI mode and limit maximal SPI speed
Patch allow to use different mode settings for SPI (MODE3 for example)
and limit maximal speed according to IC datasheet.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Alexander Shiyan [Mon, 19 Aug 2013 11:39:20 +0000 (15:39 +0400)]
can: mcp251x: Eliminate irq_flags from driver platform_data
Flags is not used by boards, so remove this field from the driver
platform_data.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Alexander Shiyan [Mon, 19 Aug 2013 11:39:19 +0000 (15:39 +0400)]
can: mcp251x: Replace power callbacks with regulator API
This patch replaces power callbacks to the regulator API. To improve
the readability of the code, helper for the regulator enable/disable
was added.
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sean Cross [Wed, 21 Aug 2013 01:46:12 +0000 (01:46 +0000)]
net/phy: micrel: Add OF configuration support for ksz9021
Some boards require custom PHY configuration, for example due to trace
length differences. Add the ability to configure these registers in
order to get the PHY to function on boards that need it.
Because PHYs are auto-detected based on MDIO device IDs, allow PHY
configuration to be specified in the parent Ethernet device node if no
PHY device node is present.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 20 Aug 2013 10:22:02 +0000 (12:22 +0200)]
net: ipv6: mcast: minor: use defines for rfc3810/8.1 lengths
Instead of hard-coding length values, use a define to make it clear
where those lengths come from.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 20 Aug 2013 10:22:01 +0000 (12:22 +0200)]
net: ipv6: minor: *_start_timer: rather use unsigned long
For the functions mld_gq_start_timer(), mld_ifc_start_timer(),
and mld_dad_start_timer(), rather use unsigned long than int
as we operate only on unsigned values anyway. This seems more
appropriate as there is no good reason to do type conversions
to int, that could lead to future errors.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 20 Aug 2013 10:22:00 +0000 (12:22 +0200)]
net: ipv6: igmp6_event_query: use msecs_to_jiffies
Use proper API functions to calculate jiffies from milliseconds and
not the crude method of dividing HZ by a value. This ensures more
accurate values even in the case of strange HZ values. While at it,
also simplify code in the mlh2 case by using max().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matus Ujhelyi [Tue, 20 Aug 2013 05:59:38 +0000 (07:59 +0200)]
net: cpsw: Add support for wake-on-lan for cpsw
Some phy's can be configured to enable wake on lan (e.g. at803x or marvell 88E1318S).
There is no way how to enable wol on CPSW with such connected phys. This patch
adds this support. It is provided by calling the phy's related code.
Tested on board with at8030x connected phy. Wol interrupt line is
connected to GPIO0 on am335x.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Mon, 19 Aug 2013 12:17:40 +0000 (17:47 +0530)]
drivers: net: cpsw: remove platform data header file of cpsw
CPSW driver no longer supports platform register as all the SoCs which has CPSW
are supporting DT only booting, so moving cpsw.h header file from platform
include to drivers/net/ethernet/ti
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Tue, 20 Aug 2013 10:16:06 +0000 (12:16 +0200)]
ip6_tunnel: ensure to always have a link local address
When an Xin6 tunnel is set up, we check other netdevices to inherit the link-
local address. If none is available, the interface will not have any link-local
address. RFC4862 expects that each interface has a link local address.
Now than this kind of tunnels supports x-netns, it's easy to fall in this case
(by creating the tunnel in a netns where ethernet interfaces stand and then
moving it to a other netns where no ethernet interface is available).
RFC4291, Appendix A suggests two methods: the first is the one currently
implemented, the second is to generate a unique identifier, so that we can
always generate the link-local address. Let's use eth_random_addr() to generate
this interface indentifier.
I remove completly the previous method, hence for the whole life of the
interface, the link-local address remains the same (previously, it depends on
which ethernet interfaces were up when the tunnel interface was set up).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 21 Aug 2013 06:44:39 +0000 (23:44 -0700)]
Revert "ipv6: fix checkpatch errors in net/ipv6/addrconf.c"
This reverts commit
df8372ca747f6da9e8590775721d9363c1dfc87e.
These changes are buggy and make unintended semantic changes
to ip6_tnl_add_linklocal().
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Mon, 19 Aug 2013 11:20:39 +0000 (13:20 +0200)]
bcm63xx_enet: replace devm_request_and_ioremap by devm_ioremap_resource
Use devm_ioremap_resource instead of devm_request_and_ioremap.
This was done using the semantic patch
scripts/coccinelle/api/devm_ioremap_resource.cocci
The relevant call to platform_get_resource was manually moved down to the
call to devm_ioremap_resource.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Mon, 19 Aug 2013 12:00:37 +0000 (20:00 +0800)]
net: davinci_mdio: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Mon, 19 Aug 2013 12:00:25 +0000 (20:00 +0800)]
net: xilinx_emaclite: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of_dev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Mon, 19 Aug 2013 11:59:36 +0000 (19:59 +0800)]
net: sunhme: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Mon, 19 Aug 2013 11:59:25 +0000 (19:59 +0800)]
net: sunbmac: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Mon, 19 Aug 2013 11:59:16 +0000 (19:59 +0800)]
net: fec_mpc52xx_phy: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Mon, 19 Aug 2013 11:59:09 +0000 (19:59 +0800)]
net: ucc_geth: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &ofdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libo Chen [Mon, 19 Aug 2013 11:58:40 +0000 (19:58 +0800)]
net: fsl_pq_mdio: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sat, 17 Aug 2013 23:13:26 +0000 (03:13 +0400)]
sh_eth: remove 'register_type' field from 'struct sh_eth_plat_data'
Now that the 'register_type' field of the 'sh_eth' driver's platform data is not
used by the driver anymore, it's time to remove it and its initializers from
the SH platform code. Also move *enum* declaring values for this field from
<linux/sh_eth.h> to the local driver's header file as they're only needed
by the driver itself now...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sat, 17 Aug 2013 23:11:28 +0000 (03:11 +0400)]
sh_eth: get register layout from 'struct sh_eth_cpu_data'
The register layout is a SoC characteristic, so it's wrong that it's stored
in the otherwise board specific platform data. Add 'register_type' field to
'struct sh_eth_cpu_data', initialize it properly for each SoC, and read it
from this structure instead of the platfrom data from now on...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sat, 17 Aug 2013 22:19:09 +0000 (02:19 +0400)]
SolutionEngine7724: fix Ether support
The Ether platform data is behind the declaration of 'struct sh_eth_plat_data'
as it's lacking the initializers for the 'register_type' and 'phy_interface'
fields -- it means they'll be implicitly and wrongly set to SH_ETH_REG_GIGABIT
and PHY_INTERFACE_MODE_NA. Initialize the fields explicitly and fix off-by-one
error in the Ether memory resource end, while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sat, 17 Aug 2013 22:15:42 +0000 (02:15 +0400)]
SH7619: fix Ether support
The 'sh_eth' driver's probe will crash as the platform code is hopelessly behind
the platform data -- it passes PHY ID instead of 'struct sh_eth_plat_data *'.
Strangely, both commit
d88a3ea6fa4c (SH7619 add ethernet controler support) that
added the platform code and commit
71557a37adb5 ([netdrvr] sh_eth: Add SH7619
support) were done in about the same time, yet the latter one added 'struct
sh_eth_plat_data' and the platform code didn't ever get updated...
Add the proper platform data and fix off-by-one memory resource end error, while
at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Mon, 19 Aug 2013 07:05:10 +0000 (10:05 +0300)]
ipip: dereferencing an ERR_PTR in ip_tunnel_init_net()
We need to move the derefernce after the IS_ERR() check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hyong-Youb Kim [Mon, 19 Aug 2013 09:02:19 +0000 (02:02 -0700)]
myri10ge: Add support for ndo_busy_poll
Add the ndo_busy_poll handler. Use skb_mark_napi_id to mark receive
packets with the napi id. For each slice, use per-slice spinlock and
state variable to ensure that only one handler processes receive
pacekts.
Locking, statistics counters, and the ndo_busy_poll handler follow
those in the ixgbe driver. So, credit goes to that driver's authors.
Signed-off-by: Hyong-Youb Kim <hykim@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 19 Aug 2013 02:08:07 +0000 (19:08 -0700)]
ipv4: raise IP_MAX_MTU to theoretical limit
As discussed last year [1], there is no compelling reason
to limit IPv4 MTU to 0xFFF0, while real limit is 0xFFFF
[1] : http://marc.info/?l=linux-netdev&m=
135607247609434&w=2
Willem raised this issue again because some of our internal
regression tests broke after lo mtu being set to 65536.
IP_MTU reports 0xFFF0, and the test attempts to send a RAW datagram of
mtu + 1 bytes, expecting the send() to fail, but it does not.
Alexey raised interesting points about TCP MSS, that should be addressed
in follow-up patches in TCP stack if needed, as someone could also set
an odd mtu anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Asias He [Mon, 19 Aug 2013 01:23:19 +0000 (09:23 +0800)]
vhost: Include linux/uio.h instead of linux/socket.h
memcpy_fromiovec is moved from net/core/iovec.c to lib/iovec.c.
linux/uio.h provides the declaration for memcpy_fromiovec.
Include linux/uio.h instead of inux/socket.h for it.
Signed-off-by: Asias He <asias@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Paasch [Sun, 18 Aug 2013 15:34:38 +0000 (17:34 +0200)]
tcp: trivial: Remove nocache argument from tcp_v4_send_synack
The nocache-argument was used in tcp_v4_send_synack as an argument to
inet_csk_route_req. However, since
ba3f7f04ef2b (ipv4: Kill
FLOWI_FLAG_RT_NOCACHE and associated code.) this is no more used.
This patch removes the unsued argument from tcp_v4_send_synack.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anders Larsen [Sun, 18 Aug 2013 09:54:40 +0000 (11:54 +0200)]
pch_gbe: ethtool cannot change parameters when link is down
When attempting to change e.g. the advertising mask when the link is down
ecmd->speed is -1 causing mii_ethtool_sset() to bail out.
This bug bit when connecting to a gigabit switch through a 4-pin (industrial)
cable, since link negotiation would not complete (both endpoints claimed to
be gigabit-capable, but this is not possible with only 4 pins).
Any attempt to fix this by setting autonegation to not offer 1000Mbps
failed as the setting would not be accepted while the link was still down...
Set ecmd->speed to SPEED_1000 to satisfy mii_ethtool_sset()
(the actual value of ecmd->speed doesn't matter as long as it is valid,
since a re-negotation is forced afterwards).
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Sun, 18 Aug 2013 08:09:30 +0000 (16:09 +0800)]
moxa: fix missing unlock on error in moxart_mac_start_xmit()
Add the missing unlock before return from function moxart_mac_start_xmit()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Kirjanov [Sat, 17 Aug 2013 05:08:49 +0000 (09:08 +0400)]
sundance: Add myself as a maintainer
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Kirjanov [Sat, 17 Aug 2013 05:08:48 +0000 (09:08 +0400)]
sundance: Add netpoll support
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dingtianhong [Sat, 17 Aug 2013 02:27:15 +0000 (10:27 +0800)]
ipv6: fix checkpatch errors in net/ipv6/addrconf.c
ERROR: code indent should use tabs where possible: fix 2.
ERROR: do not use assignment in if condition: fix 5.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dingtianhong [Sat, 17 Aug 2013 02:27:04 +0000 (10:27 +0800)]
ipv6: convert the uses of ADBG and remove the superfluous parentheses
Just follow the Joe Perches's opinion, it is a better way to fix the
style errors.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Fri, 16 Aug 2013 23:32:09 +0000 (07:32 +0800)]
vxlan: using kfree_rcu() to simplify the code
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Wu [Fri, 16 Aug 2013 23:07:53 +0000 (01:07 +0200)]
r8169,sis190: remove unnecessary length check
The ethtool core will lower the requested length to the one returned by
get_regs_len, therefore no additional check is needed in the get_regs
function.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neel Patel [Fri, 16 Aug 2013 22:47:41 +0000 (15:47 -0700)]
drivers/net: enic: Generate notification of hardware crash
This patch generates a hardware crash notification (NETDEV_REBOOT)
during reset. After a hardware crash, ENIC resets all its resources
including queue pair filters programmed by USNIC. USNIC registers for
this notification, and on receiving it, reprograms the queue pair
filters.
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neel Patel [Fri, 16 Aug 2013 22:47:40 +0000 (15:47 -0700)]
drivers/net: enic: Add an interface for USNIC to interact with firmware
This patch adds an interface for USNIC to proxy firmware commands
through ENIC.
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neel Patel [Fri, 16 Aug 2013 22:47:39 +0000 (15:47 -0700)]
drivers/net: enic: Adding support for Cisco Low Latency NIC
This patch,
- Adds new firmware commands for the new Cisco Low Latency NIC
(aka. USNIC).
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 20 Aug 2013 20:30:54 +0000 (13:30 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/pablo/nf-next
Conflicts:
net/netfilter/nf_conntrack_proto_tcp.c
The conflict had to do with overlapping changes dealing with
fixing the use of an "s32" to hold the value returned by
NAT_OFFSET().
Pablo Neira Ayuso says:
====================
The following batch contains Netfilter/IPVS updates for your net-next tree.
More specifically, they are:
* Trivial typo fix in xt_addrtype, from Phil Oester.
* Remove net_ratelimit in the conntrack logging for consistency with other
logging subsystem, from Patrick McHardy.
* Remove unneeded includes from the recently added xt_connlabel support, from
Florian Westphal.
* Allow to update conntracks via nfqueue, don't need NFQA_CFG_F_CONNTRACK for
this, from Florian Westphal.
* Remove tproxy core, now that we have socket early demux, from Florian
Westphal.
* A couple of patches to refactor conntrack event reporting to save a good
bunch of lines, from Florian Westphal.
* Fix missing locking in NAT sequence adjustment, it did not manifested in
any known bug so far, from Patrick McHardy.
* Change sequence number adjustment variable to 32 bits, to delay the
possible early overflow in long standing connections, also from Patrick.
* Comestic cleanups for IPVS, from Dragos Foianu.
* Fix possible null dereference in IPVS in the SH scheduler, from Daniel
Borkmann.
* Allow to attach conntrack expectations via nfqueue. Before this patch, you
had to use ctnetlink instead, thus, we save the conntrack lookup.
* Export xt_rpfilter and xt_HMARK header files, from Nicolas Dichtel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 20 Aug 2013 20:23:29 +0000 (13:23 -0700)]
Merge branch '6lowpan'
Alexander Aring says:
====================
6lowpan: address uncompression fixes
The current implementation to uncompress addresses in a 6lowpan header
is completely broken.
This patch series fixes the parsing of addresses in a 6lowpan header.
It contains a major rewrite of the uncompress address function to parse
the address in a correct way.
Tested with the ravenusbstick(contiki 6LoWPAN stack) and beaglebone
(linux 6LoWPAN Stack) on the other side. The linux side contains all
possible addresses for the uncompression cases. Then I type a ping6 for
each case and lookup in wireshark and dmesg the correct reconstruction.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Fri, 16 Aug 2013 19:59:59 +0000 (21:59 +0200)]
6lowpan: handle context based source address
Handle context based address when an unspecified address is given.
For other context based address we print a warning and drop the packet
because we don't support it right now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Fri, 16 Aug 2013 19:59:58 +0000 (21:59 +0200)]
6lowpan: lowpan_uncompress_addr with address_mode
This patch drops the pre and postcount calculation from the
lowpan_uncompress_addr function.We use instead a switch/case
over address_mode value. The original implementation has several
bugs in this function and it was hard to decrypt how it works.
To make it maintainable and fix these bugs this patch basically
reimplements lowpan_uncompress_addr from scratch.
A list of bugs we found in the current implementation:
1) Properly support uncompression of short-address based IPv6 addresses
(instead of basically copying garbage)
2) Fix use and uncompression of long-addresses based IPv6 addresses
3) Add missing ff:fe00 in the case of SAM/DAM = 2 and M = 0
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Fri, 16 Aug 2013 19:59:57 +0000 (21:59 +0200)]
6lowpan: add function to uncompress multicast addr
Add function to uncompress multicast address.
This function split the uncompress function for a multicast address
in a seperate function.
To uncompress a multicast address is different than a other
non-multicasts addresses according to rfc6282.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Fri, 16 Aug 2013 19:59:56 +0000 (21:59 +0200)]
6lowpan: introduce lowpan_fetch_skb function
This patch adds a helper function to parse the ipv6 header to a
6lowpan header in stream.
This function checks first if we can pull data with a specific
length from a skb. If this seems to be okay, we copy skb data to
a destination pointer and run skb_pull.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Hauweele [Fri, 16 Aug 2013 19:59:55 +0000 (21:59 +0200)]
6lowpan: Fix fragmentation with link-local compressed addresses
When a new 6lowpan fragment is received, a skbuff is allocated for
the reassembled packet. However when a 6lowpan packet compresses
link-local addresses based on link-layer addresses, the processing
function relies on the skb mac control block to find the related
link-layer address.
This patch copies the control block from the first fragment into
the newly allocated skb to keep a trace of the link-layer addresses
in case of a link-local compressed address.
Edit: small changes on comment issue
Signed-off-by: David Hauweele <david@hauweele.net>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Fri, 16 Aug 2013 19:59:54 +0000 (21:59 +0200)]
6lowpan: init ipv6hdr buffer to zero
This patch simplify the handling to set fields inside of struct ipv6hdr
to zero. Instead of setting some memory regions with memset to zero we
initialize the whole ipv6hdr to zero.
This is a simplification for parsing the 6lowpan header for the upcomming
patches.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Himanshu Madhani [Fri, 16 Aug 2013 23:07:17 +0000 (19:07 -0400)]
qlcnic: Update version to 5.3.47
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pratik Pujar [Fri, 16 Aug 2013 23:07:16 +0000 (19:07 -0400)]
qlcnic: Add support for 84xx adapters to load firmware from file
o Use appropriate firmware image file name based on device IDs.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Fri, 16 Aug 2013 23:07:15 +0000 (19:07 -0400)]
qlcnic: Loopback Inter Driver Communication AEN handler
o Loopback initiator function drivers should process loopback time extend AEN.
These AENs are triggered by the loopback time extend mailbox command
issued by the target function drivers.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>