OSDN Git Service
ludovic.desroches@atmel.com [Wed, 29 Jul 2015 14:22:47 +0000 (16:22 +0200)]
mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC
Introduce driver for he Atmel SDMMC available on sama5d2. It is a sdhci
compliant controller.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ludovic.desroches@atmel.com [Wed, 29 Jul 2015 14:22:46 +0000 (16:22 +0200)]
mmc: sdhci: switch from programmable clock mode to divided one if needed
In programmable mode, if the clock frequency is too high, the divider
can be too small to meet the clock frequency requirement especially to
init the SD card. In this case, switch to the divided clock mode.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Addy Ke [Mon, 10 Aug 2015 16:27:18 +0000 (01:27 +0900)]
mmc: dw_mmc: add quirk for broken data transfer over scheme
This patch add a new quirk to add a s/w timer to notify the driver
to terminate current transfer and report a data timeout to the core,
if DTO interrupt does NOT come within the given time.
dw_mmc call mmc_request_done func to finish transfer depends on
DTO interrupt. If DTO interrupt does not come in sending data state,
the current transfer will be blocked.
We got the reply from synopsys:
There are two counters but both use the same value of [31:8] bits.
Data timeout counter doesn't wait for stop clock and you should get
DRTO even when the clock is not stopped.
Host Starvation timeout counter is triggered with stop clock condition.
This means that host should get DRTO and DTO interrupt.
But this case really exists, when driver reads tuning data from
card on RK3288-pink2 board. I measured waveforms by oscilloscope
and found that card clock was always on and data lines were always
holded high level in sending data state.
There are two possibility that data over interrupt doesn't come in
reading data state on RK3X SoCs:
- get command done interrupt, but doesn't get any data-related interrupt.
- get data error interrupt, but doesn't get data over interrupt.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Jaehoon Chung [Thu, 6 Aug 2015 07:23:26 +0000 (16:23 +0900)]
mmc: dw_mmc: print the message for deprecated property
supports-highspeed was deprecated.
If someone use it, we need to notice information for it.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Jaehoon Chung [Thu, 6 Aug 2015 07:23:25 +0000 (16:23 +0900)]
mmc: dw_mmc: remove the unused blk_setting
"blk_setting" doesn't use anywhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Jaehoon Chung [Thu, 6 Aug 2015 07:23:24 +0000 (16:23 +0900)]
mmc: dw_mmc: fix the wrong condition checking
When num-slots is lower than 1, it's right that should be returned -ENODEV.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Heiko Stuebner [Mon, 3 Aug 2015 15:04:10 +0000 (17:04 +0200)]
mmc: dw_mmc: fix pio mode when internal dmac is enabled
The dw_mci_init_dma() may decide to not use dma, but pio instead, caused
by things like wrong dma settings in the system.
Till now the code dw_mci_init_slot() always assumed that dma is available
when CONFIG_MMC_DW_IDMAC was defined, ignoring the host->use_dma var
set during dma init.
So when now the dma init failed for whatever reason, the transfer sizes
would still be set for dma transfers, especially including the maximum
block-count calculated from host->ring_size and resulting in a
[ 4.991109] ------------[ cut here ]------------
[ 4.991111] kernel BUG at drivers/mmc/core/core.c:256!
[ 4.991113] Internal error: Oops - BUG: 0 [#1] SMP ARM
because host->ring_size is 0 in this case and the slot init code uses
the wrong code to calculate the values.
Fix this by selecting the correct calculations using the host->use_dma
variable instead of the CONFIG_MMC_DW_IDMAC config option.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Shawn Lin [Mon, 3 Aug 2015 07:07:21 +0000 (15:07 +0800)]
mmc: dw_mmc: Fix coding style issues
This patch fixes the following issues reported by checkpatch.pl:
- use -EINVAL instead of -ENOSYS, to fix warning message:
"ENOSYS means 'invalid syscall nr' and nothing else"
- split lines whose length is greater than 80 characters
- avoid quoted string split across lines
- use min_t instead of min, to fix warning message:
"min() should probably be min_t(int, cnt, host->part_buf_count)"
- fix missing a blank line after declarations
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Alexey Brodkin [Thu, 25 Jun 2015 08:25:07 +0000 (11:25 +0300)]
mmc: dw_mmc: handle data blocks > than 4kB if IDMAC is used
As per DW MobileStorage databook "each descriptor can transfer up to 4kB
of data in chained mode", moreover buffer size that is put in "des1" is
limited to 13 bits, i.e. for example on attempt to
IDMAC_SET_BUFFER1_SIZE(desc, 8192) size value that's effectively written
will be 0.
On the platform with 8kB PAGE_SIZE I see dw_mmc gets data blocks in
SG-list of 8kB size and that leads to unpredictable behavior of the
SD/MMC controller.
In particular on write to FAT partition of SD-card the controller will
stuck in the middle of DMA transaction.
Solution to the problem is simple - we need to pass large (> 4kB) data
buffers to the controller via multiple descriptors. And that's what
that change does.
What's interesting I did try original driver on same platform but
configured with 4kB PAGE_SIZE and may confirm that data blocks passed
in SG-list to dw_mmc never exeed 4kB limit - that explains why nobody
ever faced a problem I did.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Seungwon Jeon <tgih.jun@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: arc-linux-dev@synopsys.com
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Yangbo Lu [Fri, 10 Jul 2015 03:44:03 +0000 (11:44 +0800)]
mmc: block: add fixup of broken CMD23 for Sandisk card
Some Sandisk cards(such as "SDMB-32" and "SDM032" cards)
can't support CMD23, and would generate CMD timeout. So add
FIX-UP for these two types Sandisk cards.
Error log:
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
end_request: I/O error, dev mmcblk0, sector 0
Buffer I/O error on device mmcblk0, logical block 0
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Yangbo Lu [Fri, 10 Jul 2015 03:42:37 +0000 (11:42 +0800)]
mmc: sdhci-esdhc: add default quirk SDHCI_QUIRK_NO_HISPD_BIT
eSDHC supports high speed mode, but has no enabling bit for it.
Add this quirk to avoid writing to eSDHC_PROCTL[DTW] by mistake.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Yangbo Lu [Fri, 10 Jul 2015 03:36:45 +0000 (11:36 +0800)]
mmc: sdio: avoid using NULL sdio_irq_thread pointer
For Freescale QorIQ LS1021AQDS board, there is a SDIO interrupt
in the process of resume without inserting SD adapter because of
some unknown issue. But the driver doesn't assign sdio_irq_thread
pointer. This will block the resume of kernel. This patch is used
to avoid using NULL sdio_irq_thread pointer.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andreas Fenkart [Tue, 7 Jul 2015 18:38:44 +0000 (20:38 +0200)]
mmc: omap_hsmmc: regulator automatically released by devm
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andreas Fenkart [Tue, 7 Jul 2015 18:38:43 +0000 (20:38 +0200)]
mmc: omap_hsmmc: call omap_hsmmc_set_power directly
If no pdata.set_power was set by the platform code, the driver
was updating pdata with its own fallback function. This is a no-no
since pdata shall be read-only.
This patch pushes the check 'pdata->set_power != NULL' down into
the fallback functions. If pdata.set_power is really set, it calls them
and exits, otherwise the fallback code is used.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andreas Fenkart [Tue, 7 Jul 2015 17:53:10 +0000 (19:53 +0200)]
Documentation: dt: update ti,am33xx-hsmmc swakeup workaround
Before
5b83b2234be6733cf the driver was hard coding the wakeup irq to
be active low. The generic pm wakeirq does not override the active
high/low parameter, hence it must be specified correctly in the
device tree.
Mind that SDIO IRQ is active low as defined in the SDIO specification
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ivan T. Ivanov [Mon, 6 Jul 2015 12:16:21 +0000 (15:16 +0300)]
mmc: sdhci: properly check card present state when quirk NO_CARD_NO_RESET is set
Controller could have both NO_CARD_NO_RESET and BROKEN_CARD_DETECTION
quirks set. Use sdhci_do_get_cd() when applying NO_CARD_NO_RESET, which
properly check for BROKEN_CARD_DETECTION quirk.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ivan T. Ivanov [Mon, 6 Jul 2015 12:16:20 +0000 (15:16 +0300)]
mmc: sdhci: don't use card state polling when CD GPIO is defined
There is no reason to use polling for card detection state change when
drivers are using dedicated GPIO for this. Don't poll in this case.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ivan T. Ivanov [Mon, 6 Jul 2015 12:16:19 +0000 (15:16 +0300)]
mmc: sdhci: let GPIO based card detection have higher precedence
Controller could have BROKEN_CARD_DETECTION quirk set, but drivers
could use GPIO to detect card present state. Let, when defined, GPIO
take precedence, so drivers could properly detect card state and not
use polling.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ivan T. Ivanov [Mon, 6 Jul 2015 11:53:38 +0000 (14:53 +0300)]
mmc: sdhci-msm: Boost controller core clock
Ensure SDCC is working with maximum clock otherwise card
detection could be extremely slow, up to 7 seconds.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andy Shevchenko [Wed, 24 Jun 2015 11:32:21 +0000 (14:32 +0300)]
mmc: block: don't use parameter prefix if built as module
It's excessive to use prefix for the parameters when you do
modprobe mmc-block mmcblk.perdev_minors=16
Make this available only for built-in case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fabian Frederick [Tue, 16 Jun 2015 19:15:15 +0000 (21:15 +0200)]
mmc: omap: use for_each_sg() for scatterlist parsing
See Documentation/DMA-API.txt - Part Id
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Suneel Garapati [Tue, 9 Jun 2015 07:31:51 +0000 (13:01 +0530)]
mmc: sdhci-of-arasan: add quirks for broken clock base
adding SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,SDHCI_QUIRK2_PRESET_VALUE_BROKEN
flags for arasan sdhc.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Suneel Garapati [Tue, 9 Jun 2015 07:31:50 +0000 (13:01 +0530)]
mmc: sdhci: add quirk SDHCI_QUIRK_CLOCK_DIV_ZERO_BROKEN
adds quirk for controllers whose clock divider zero is broken,
sdhci_set_clock function will incorporate this modification.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Daniel Mack [Sat, 6 Jun 2015 21:15:22 +0000 (23:15 +0200)]
mmc: pxamci: switch over to dmaengine use
Switch over pxamci to dmaengine. This prepares the devicetree full
support of pxamci.
This was successfully tested on a PXA3xx board, as well as PXA27x.
Signed-off-by: Daniel Mack <zonque@gmail.com>
[adapted to pxa-dma]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
David Jander [Tue, 23 Jun 2015 09:43:52 +0000 (11:43 +0200)]
mmc: core: Optimize case for exactly one erase-group budget
In the (not so unlikely) case that the mmc controller timeout budget is
enough for exactly one erase-group, the simplification of allowing one
sector has an enormous performance penalty. We optimize this special case
by introducing a flag that prohibits erase-group boundary crossing, so
that we can allow trimming more than one sector at a time.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Linus Torvalds [Sun, 16 Aug 2015 23:34:13 +0000 (16:34 -0700)]
Linux 4.2-rc7
Linus Torvalds [Sun, 16 Aug 2015 22:44:33 +0000 (15:44 -0700)]
Merge tag 'armsoc-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A smallish batch of fixes, a little more than expected this late, but
all fixes are contained to their platforms and seem reasonably low
risk:
- a somewhat large SMP fix for ux500 that still seemed warranted to
include here
- OMAP DT fixes for pbias regulator specification that broke due to
some DT reshuffling
- PCIe IRQ routing bugfix for i.MX
- networking fixes for keystone
- runtime PM for OMAP GPMC
- a couple of error path bug fixes for exynos"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: keystone: Fix the mdio bindings by moving it to soc specific file
ARM: dts: keystone: fix the clock node for mdio
memory: omap-gpmc: Don't try to save uninitialized GPMC context
ARM: imx6: correct i.MX6 PCIe interrupt routing
ARM: ux500: add an SMP enablement type and move cpu nodes
ARM: dts: dra7: Fix broken pbias device creation
ARM: dts: OMAP5: Fix broken pbias device creation
ARM: dts: OMAP4: Fix broken pbias device creation
ARM: dts: omap243x: Fix broken pbias device creation
ARM: EXYNOS: fix double of_node_put() on error path
ARM: EXYNOS: Fix potentian kfree() of ro memory
Linus Torvalds [Sun, 16 Aug 2015 22:39:31 +0000 (15:39 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS bugfix from Ralf Baechle:
"Only a single MIPS fix - the math when invoking syscall_trace_enter
was wrong"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix seccomp syscall argument for MIPS64
Linus Torvalds [Sun, 16 Aug 2015 22:11:25 +0000 (15:11 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Merge x86 fixes from Ingo Molnar:
"Two followup fixes related to the previous LDT fix"
Also applied a further FPU emulation fix from Andy Lutomirski to the
branch before actually merging it.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
x86/ldt: Further fix FPU emulation
x86/ldt: Correct FPU emulation access to LDT
x86/ldt: Correct LDT access in single stepping logic
Andy Lutomirski [Fri, 14 Aug 2015 22:02:55 +0000 (15:02 -0700)]
x86/ldt: Further fix FPU emulation
The previous fix confused a selector with a segment prefix. Fix it.
Compile-tested only.
Cc: stable@vger.kernel.org
Cc: Juergen Gross <jgross@suse.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes:
4809146b86c3 ("x86/ldt: Correct FPU emulation access to LDT")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jann Horn [Sun, 16 Aug 2015 18:27:01 +0000 (20:27 +0200)]
fs/fuse: fix ioctl type confusion
fuse_dev_ioctl() performed fuse_get_dev() on a user-supplied fd,
leading to a type confusion issue. Fix it by checking file->f_op.
Signed-off-by: Jann Horn <jann@thejh.net>
Acked-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Sun, 16 Aug 2015 19:29:57 +0000 (21:29 +0200)]
Merge tag 'keystone-dts-late-fixes-v2' of git://git./linux/kernel/git/ssantosh/linux-keystone into fixes
ARM: Couple of Keysyone MDIO DTS fixes for 4.2-rc6+
These are necessary to get the NIC card working on all Keystone
EVMs. Couple of boards are broken without these two fixes.
* tag 'keystone-dts-late-fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone: Fix the mdio bindings by moving it to soc specific file
ARM: dts: keystone: fix the clock node for mdio
Signed-off-by: Olof Johansson <olof@lixom.net>
Markos Chandras [Thu, 13 Aug 2015 07:47:59 +0000 (08:47 +0100)]
MIPS: Fix seccomp syscall argument for MIPS64
Commit
4c21b8fd8f14 ("MIPS: seccomp: Handle indirect system calls (o32)")
fixed indirect system calls on O32 but it also introduced a bug for MIPS64
where it erroneously modified the v0 (syscall) register with the assumption
that the sycall offset hasn't been taken into consideration. This breaks
seccomp on MIPS64 n64 and n32 ABIs. We fix this by replacing the addition
with a move instruction.
Fixes:
4c21b8fd8f14 ("MIPS: seccomp: Handle indirect system calls (o32)")
Cc: <stable@vger.kernel.org> # 3.15+
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10951/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds [Sat, 15 Aug 2015 20:54:53 +0000 (13:54 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This has two libfc fixes for bugs causing rare crashes, one iscsi fix
for a potential hang on shutdown, and a fix for an I/O blocksize issue
which caused a regression"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
sd: Fix maximum I/O size for BLOCK_PC requests
libfc: Fix fc_fcp_cleanup_each_cmd()
libfc: Fix fc_exch_recv_req() error path
libiscsi: Fix host busy blocking during connection teardown
Linus Torvalds [Sat, 15 Aug 2015 00:27:52 +0000 (17:27 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Just two very small & simple patches"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Use adjustment in guest cycles when handling MSR_IA32_TSC_ADJUST
KVM: x86: zero IDT limit on entry to SMM
Linus Torvalds [Sat, 15 Aug 2015 00:05:26 +0000 (17:05 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge fixes from Andrew Morton:
"11 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
Update maintainers for DRM STI driver
mm: cma: mark cma_bitmap_maxno() inline in header
zram: fix pool name truncation
memory-hotplug: fix wrong edge when hot add a new node
.mailmap: Andrey Ryabinin has moved
ipc/sem.c: update/correct memory barriers
mm/hwpoison: fix panic due to split huge zero page
ipc,sem: remove uneeded sem_undo_list lock usage in exit_sem()
ipc,sem: fix use after free on IPC_RMID after a task using same semaphore set exits
mm/hwpoison: fix fail isolate hugetlbfs page w/ refcount held
mm/hwpoison: fix page refcount of unknown non LRU page
Linus Torvalds [Fri, 14 Aug 2015 23:10:04 +0000 (16:10 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clock fix from Stephen Boyd:
"A one-liner for a regression found in the PXA clock driver"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: pxa: pxa3xx: fix CKEN register access
Benjamin Gaignard [Fri, 14 Aug 2015 22:35:24 +0000 (15:35 -0700)]
Update maintainers for DRM STI driver
Add Vincent Abriou and myself as maintainers.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gregory Fong [Fri, 14 Aug 2015 22:35:21 +0000 (15:35 -0700)]
mm: cma: mark cma_bitmap_maxno() inline in header
cma_bitmap_maxno() was marked as static and not static inline, which can
cause warnings about this function not being used if this file is included
in a file that does not call that function, and violates the conventions
used elsewhere. The two options are to move the function implementation
back to mm/cma.c or make it inline here, and it's simple enough for the
latter to make sense.
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sergey Senozhatsky [Fri, 14 Aug 2015 22:35:19 +0000 (15:35 -0700)]
zram: fix pool name truncation
zram_meta_alloc() constructs a pool name for zs_create_pool() call as
snprintf(pool_name, sizeof(pool_name), "zram%d", device_id);
However, it defines pool name buffer to be only 8 bytes long (minus
trailing zero), which means that we can have only 1000 pool names: zram0
-- zram999.
With CONFIG_ZSMALLOC_STAT enabled an attempt to create a device zram1000
can fail if device zram100 already exists, because snprintf() will
truncate new pool name to zram100 and pass it debugfs_create_dir(),
causing:
debugfs dir <zram100> creation failed
zram: Error creating memory pool
... and so on.
Fix it by passing zram->disk->disk_name to zram_meta_alloc() instead of
divice_id. We construct zram%d name earlier and keep it as a ->disk_name,
no need to snprintf() it again.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xishi Qiu [Fri, 14 Aug 2015 22:35:16 +0000 (15:35 -0700)]
memory-hotplug: fix wrong edge when hot add a new node
When we add a new node, the edge of memory may be wrong.
e.g. system has 4 nodes, and node3 is movable, node3 mem:[24G-32G],
1. hotremove the node3,
2. then hotadd node3 with a part of memory, mem:[26G-30G],
3. call hotadd_new_pgdat()
free_area_init_node()
get_pfn_range_for_nid()
4. it will return wrong start_pfn and end_pfn, because we have not
update the memblock.
This patch also fixes a BUG_ON during hot-addition, please see
http://marc.info/?l=linux-kernel&m=
142961156129456&w=2
Signed-off-by: Xishi Qiu <qiuxishi@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Taku Izumi <izumi.taku@jp.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Fri, 14 Aug 2015 22:35:13 +0000 (15:35 -0700)]
.mailmap: Andrey Ryabinin has moved
Update my email address.
Signed-off-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Manfred Spraul [Fri, 14 Aug 2015 22:35:10 +0000 (15:35 -0700)]
ipc/sem.c: update/correct memory barriers
sem_lock() did not properly pair memory barriers:
!spin_is_locked() and spin_unlock_wait() are both only control barriers.
The code needs an acquire barrier, otherwise the cpu might perform read
operations before the lock test.
As no primitive exists inside <include/spinlock.h> and since it seems
noone wants another primitive, the code creates a local primitive within
ipc/sem.c.
With regards to -stable:
The change of sem_wait_array() is a bugfix, the change to sem_lock() is a
nop (just a preprocessor redefinition to improve the readability). The
bugfix is necessary for all kernels that use sem_wait_array() (i.e.:
starting from 3.10).
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Reported-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Kirill Tkhai <ktkhai@parallels.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wanpeng Li [Fri, 14 Aug 2015 22:35:08 +0000 (15:35 -0700)]
mm/hwpoison: fix panic due to split huge zero page
Bug:
------------[ cut here ]------------
kernel BUG at mm/huge_memory.c:1957!
invalid opcode: 0000 [#1] SMP
Modules linked in: snd_hda_codec_hdmi i915 rpcsec_gss_krb5 snd_hda_codec_realtek snd_hda_codec_generic nfsv4 dns_re
CPU: 2 PID: 2576 Comm: test_huge Not tainted 4.2.0-rc5-mm1+ #27
Hardware name: Dell Inc. OptiPlex 7020/0F5C5X, BIOS A03 01/08/2015
task:
ffff880204e3d600 ti:
ffff8800db16c000 task.ti:
ffff8800db16c000
RIP: split_huge_page_to_list+0xdb/0x120
Call Trace:
memory_failure+0x32e/0x7c0
madvise_hwpoison+0x8b/0x160
SyS_madvise+0x40/0x240
? do_page_fault+0x37/0x90
entry_SYSCALL_64_fastpath+0x12/0x71
Code: ff f0 41 ff 4c 24 30 74 0d 31 c0 48 83 c4 08 5b 41 5c 41 5d c9 c3 4c 89 e7 e8 e2 58 fd ff 48 83 c4 08 31 c0
RIP split_huge_page_to_list+0xdb/0x120
RSP <
ffff8800db16fde8>
---[ end trace
aee7ce0df8e44076 ]---
Testcase:
#define _GNU_SOURCE
#include <stdlib.h>
#include <stdio.h>
#include <sys/mman.h>
#include <unistd.h>
#include <fcntl.h>
#include <sys/types.h>
#include <errno.h>
#include <string.h>
#define MB 1024*1024
int main(void)
{
char *mem;
posix_memalign((void **)&mem, 2 * MB, 200 * MB);
madvise(mem, 200 * MB, MADV_HWPOISON);
free(mem);
return 0;
}
Huge zero page is allocated if page fault w/o FAULT_FLAG_WRITE flag.
The get_user_pages_fast() which called in madvise_hwpoison() will get
huge zero page if the page is not allocated before. Huge zero page is a
tranparent huge page, however, it is not an anonymous page.
memory_failure will split the huge zero page and trigger
BUG_ON(is_huge_zero_page(page));
After commit
98ed2b0052e6 ("mm/memory-failure: give up error handling
for non-tail-refcounted thp"), memory_failure will not catch non anon
thp from madvise_hwpoison path and this bug occur.
Fix it by catching non anon thp in memory_failure in order to not split
huge zero page in madvise_hwpoison path.
After this patch:
Injecting memory failure for page 0x202800 at 0x7fd8ae800000
MCE: 0x202800: non anonymous thp
[...]
[akpm@linux-foundation.org: remove second split, per Wanpeng]
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Herton R. Krzesinski [Fri, 14 Aug 2015 22:35:05 +0000 (15:35 -0700)]
ipc,sem: remove uneeded sem_undo_list lock usage in exit_sem()
After we acquire the sma->sem_perm lock in exit_sem(), we are protected
against a racing IPC_RMID operation. Also at that point, we are the last
user of sem_undo_list. Therefore it isn't required that we acquire or use
ulp->lock.
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Acked-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Rafael Aquini <aquini@redhat.com>
CC: Aristeu Rozanski <aris@redhat.com>
Cc: David Jeffery <djeffery@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Herton R. Krzesinski [Fri, 14 Aug 2015 22:35:02 +0000 (15:35 -0700)]
ipc,sem: fix use after free on IPC_RMID after a task using same semaphore set exits
The current semaphore code allows a potential use after free: in
exit_sem we may free the task's sem_undo_list while there is still
another task looping through the same semaphore set and cleaning the
sem_undo list at freeary function (the task called IPC_RMID for the same
semaphore set).
For example, with a test program [1] running which keeps forking a lot
of processes (which then do a semop call with SEM_UNDO flag), and with
the parent right after removing the semaphore set with IPC_RMID, and a
kernel built with CONFIG_SLAB, CONFIG_SLAB_DEBUG and
CONFIG_DEBUG_SPINLOCK, you can easily see something like the following
in the kernel log:
Slab corruption (Not tainted): kmalloc-64 start=
ffff88003b45c1c0, len=64
000: 6b 6b 6b 6b 6b 6b 6b 6b 00 6b 6b 6b 6b 6b 6b 6b kkkkkkkk.kkkkkkk
010: ff ff ff ff 6b 6b 6b 6b ff ff ff ff ff ff ff ff ....kkkk........
Prev obj: start=
ffff88003b45c180, len=64
000: 00 00 00 00 ad 4e ad de ff ff ff ff 5a 5a 5a 5a .....N......ZZZZ
010: ff ff ff ff ff ff ff ff c0 fb 01 37 00 88 ff ff ...........7....
Next obj: start=
ffff88003b45c200, len=64
000: 00 00 00 00 ad 4e ad de ff ff ff ff 5a 5a 5a 5a .....N......ZZZZ
010: ff ff ff ff ff ff ff ff 68 29 a7 3c 00 88 ff ff ........h).<....
BUG: spinlock wrong CPU on CPU#2, test/18028
general protection fault: 0000 [#1] SMP
Modules linked in: 8021q mrp garp stp llc nf_conntrack_ipv4 nf_defrag_ipv4 ip6t_REJECT nf_reject_ipv6 nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables binfmt_misc ppdev input_leds joydev parport_pc parport floppy serio_raw virtio_balloon virtio_rng virtio_console virtio_net iosf_mbi crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcspkr qxl ttm drm_kms_helper drm snd_hda_codec_generic i2c_piix4 snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep snd_seq snd_seq_device snd_pcm snd_timer snd soundcore crc32c_intel virtio_pci virtio_ring virtio pata_acpi ata_generic [last unloaded: speedstep_lib]
CPU: 2 PID: 18028 Comm: test Not tainted 4.2.0-rc5+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.8.1-20150318_183358- 04/01/2014
RIP: spin_dump+0x53/0xc0
Call Trace:
spin_bug+0x30/0x40
do_raw_spin_unlock+0x71/0xa0
_raw_spin_unlock+0xe/0x10
freeary+0x82/0x2a0
? _raw_spin_lock+0xe/0x10
semctl_down.clone.0+0xce/0x160
? __do_page_fault+0x19a/0x430
? __audit_syscall_entry+0xa8/0x100
SyS_semctl+0x236/0x2c0
? syscall_trace_leave+0xde/0x130
entry_SYSCALL_64_fastpath+0x12/0x71
Code: 8b 80 88 03 00 00 48 8d 88 60 05 00 00 48 c7 c7 a0 2c a4 81 31 c0 65 8b 15 eb 40 f3 7e e8 08 31 68 00 4d 85 e4 44 8b 4b 08 74 5e <45> 8b 84 24 88 03 00 00 49 8d 8c 24 60 05 00 00 8b 53 04 48 89
RIP [<
ffffffff810d6053>] spin_dump+0x53/0xc0
RSP <
ffff88003750fd68>
---[ end trace
783ebb76612867a0 ]---
NMI watchdog: BUG: soft lockup - CPU#3 stuck for 22s! [test:18053]
Modules linked in: 8021q mrp garp stp llc nf_conntrack_ipv4 nf_defrag_ipv4 ip6t_REJECT nf_reject_ipv6 nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables binfmt_misc ppdev input_leds joydev parport_pc parport floppy serio_raw virtio_balloon virtio_rng virtio_console virtio_net iosf_mbi crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcspkr qxl ttm drm_kms_helper drm snd_hda_codec_generic i2c_piix4 snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep snd_seq snd_seq_device snd_pcm snd_timer snd soundcore crc32c_intel virtio_pci virtio_ring virtio pata_acpi ata_generic [last unloaded: speedstep_lib]
CPU: 3 PID: 18053 Comm: test Tainted: G D 4.2.0-rc5+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.8.1-20150318_183358- 04/01/2014
RIP: native_read_tsc+0x0/0x20
Call Trace:
? delay_tsc+0x40/0x70
__delay+0xf/0x20
do_raw_spin_lock+0x96/0x140
_raw_spin_lock+0xe/0x10
sem_lock_and_putref+0x11/0x70
SYSC_semtimedop+0x7bf/0x960
? handle_mm_fault+0xbf6/0x1880
? dequeue_task_fair+0x79/0x4a0
? __do_page_fault+0x19a/0x430
? kfree_debugcheck+0x16/0x40
? __do_page_fault+0x19a/0x430
? __audit_syscall_entry+0xa8/0x100
? do_audit_syscall_entry+0x66/0x70
? syscall_trace_enter_phase1+0x139/0x160
SyS_semtimedop+0xe/0x10
SyS_semop+0x10/0x20
entry_SYSCALL_64_fastpath+0x12/0x71
Code: 47 10 83 e8 01 85 c0 89 47 10 75 08 65 48 89 3d 1f 74 ff 7e c9 c3 0f 1f 44 00 00 55 48 89 e5 e8 87 17 04 00 66 90 c9 c3 0f 1f 00 <55> 48 89 e5 0f 31 89 c1 48 89 d0 48 c1 e0 20 89 c9 48 09 c8 c9
Kernel panic - not syncing: softlockup: hung tasks
I wasn't able to trigger any badness on a recent kernel without the
proper config debugs enabled, however I have softlockup reports on some
kernel versions, in the semaphore code, which are similar as above (the
scenario is seen on some servers running IBM DB2 which uses semaphore
syscalls).
The patch here fixes the race against freeary, by acquiring or waiting
on the sem_undo_list lock as necessary (exit_sem can race with freeary,
while freeary sets un->semid to -1 and removes the same sem_undo from
list_proc or when it removes the last sem_undo).
After the patch I'm unable to reproduce the problem using the test case
[1].
[1] Test case used below:
#include <stdio.h>
#include <sys/types.h>
#include <sys/ipc.h>
#include <sys/sem.h>
#include <sys/wait.h>
#include <stdlib.h>
#include <time.h>
#include <unistd.h>
#include <errno.h>
#define NSEM 1
#define NSET 5
int sid[NSET];
void thread()
{
struct sembuf op;
int s;
uid_t pid = getuid();
s = rand() % NSET;
op.sem_num = pid % NSEM;
op.sem_op = 1;
op.sem_flg = SEM_UNDO;
semop(sid[s], &op, 1);
exit(EXIT_SUCCESS);
}
void create_set()
{
int i, j;
pid_t p;
union {
int val;
struct semid_ds *buf;
unsigned short int *array;
struct seminfo *__buf;
} un;
/* Create and initialize semaphore set */
for (i = 0; i < NSET; i++) {
sid[i] = semget(IPC_PRIVATE , NSEM, 0644 | IPC_CREAT);
if (sid[i] < 0) {
perror("semget");
exit(EXIT_FAILURE);
}
}
un.val = 0;
for (i = 0; i < NSET; i++) {
for (j = 0; j < NSEM; j++) {
if (semctl(sid[i], j, SETVAL, un) < 0)
perror("semctl");
}
}
/* Launch threads that operate on semaphore set */
for (i = 0; i < NSEM * NSET * NSET; i++) {
p = fork();
if (p < 0)
perror("fork");
if (p == 0)
thread();
}
/* Free semaphore set */
for (i = 0; i < NSET; i++) {
if (semctl(sid[i], NSEM, IPC_RMID))
perror("IPC_RMID");
}
/* Wait for forked processes to exit */
while (wait(NULL)) {
if (errno == ECHILD)
break;
};
}
int main(int argc, char **argv)
{
pid_t p;
srand(time(NULL));
while (1) {
p = fork();
if (p < 0) {
perror("fork");
exit(EXIT_FAILURE);
}
if (p == 0) {
create_set();
goto end;
}
/* Wait for forked processes to exit */
while (wait(NULL)) {
if (errno == ECHILD)
break;
};
}
end:
return 0;
}
[akpm@linux-foundation.org: use normal comment layout]
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Acked-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Rafael Aquini <aquini@redhat.com>
CC: Aristeu Rozanski <aris@redhat.com>
Cc: David Jeffery <djeffery@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wanpeng Li [Fri, 14 Aug 2015 22:34:59 +0000 (15:34 -0700)]
mm/hwpoison: fix fail isolate hugetlbfs page w/ refcount held
Hugetlbfs pages will get a refcount in get_any_page() or
madvise_hwpoison() if soft offlining through madvise. The refcount which
is held by the soft offline path should be released if we fail to isolate
hugetlbfs pages.
Fix it by reducing the refcount for both isolation success and failure.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: <stable@vger.kernel.org> [3.9+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wanpeng Li [Fri, 14 Aug 2015 22:34:56 +0000 (15:34 -0700)]
mm/hwpoison: fix page refcount of unknown non LRU page
After trying to drain pages from pagevec/pageset, we try to get reference
count of the page again, however, the reference count of the page is not
reduced if the page is still not on LRU list.
Fix it by adding the put_page() to drop the page reference which is from
__get_any_page().
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: <stable@vger.kernel.org> [3.9+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 14 Aug 2015 18:06:43 +0000 (11:06 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"A single clocksource driver suspend/resume fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents/drivers/sh_cmt: Only perform clocksource suspend/resume if enabled
Linus Torvalds [Fri, 14 Aug 2015 17:57:16 +0000 (10:57 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc fixes: PMU driver corner cases, tooling fixes, and an 'AUX'
(Intel PT) race related core fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/cqm: Do not access cpu_data() from CPU_UP_PREPARE handler
perf/x86/intel: Fix memory leak on hot-plug allocation fail
perf: Fix PERF_EVENT_IOC_PERIOD migration race
perf: Fix double-free of the AUX buffer
perf: Fix fasync handling on inherited events
perf tools: Fix test build error when bindir contains double slash
perf stat: Fix transaction lenght metrics
perf: Fix running time accounting
Linus Torvalds [Fri, 14 Aug 2015 17:45:23 +0000 (10:45 -0700)]
Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull locking fix from Ingo Molnar:
"A single fix for a locking self-test crash"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/pvqspinlock: Fix kernel panic in locking-selftest
Linus Torvalds [Fri, 14 Aug 2015 17:39:32 +0000 (10:39 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Back from holidays, found these in the cracks: one nouveau revert, one
vmwgfx locking fix and a bunch of exynos fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "drm/nouveau/fifo/gk104: kick channels when deactivating them"
drm/vmwgfx: Fix execbuf locking issues
drm/exynos/fimc: fix runtime pm support
drm/exynos/mixer: always update INT_EN cache
drm/exynos/mixer: correct vsync configuration sequence
drm/exynos/mixer: fix interrupt clearing
drm/exynos/hdmi: fix edid memory leak
drm/exynos: gsc: fix wrong bitwise operation for swap detection
Alexandre Courbot [Wed, 12 Aug 2015 04:17:38 +0000 (13:17 +0900)]
Revert "drm/nouveau/fifo/gk104: kick channels when deactivating them"
This reverts commit
1addc1264852
This commit seems to cause crashes in gk104_fifo_intr_runlist() by
returning 0xbad0da00 when register 0x2a00 is read. Since this commit was
intended for GM20B which is not completely supported yet, let's revert
it for the time being.
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Thomas Hellstrom [Wed, 12 Aug 2015 05:31:17 +0000 (22:31 -0700)]
drm/vmwgfx: Fix execbuf locking issues
This addresses two issues that cause problems with viewperf maya-03 in
situation with memory pressure.
The first issue causes attempts to unreserve buffers if batched
reservation fails due to, for example, a signal pending. While previously
the ttm_eu api was resistant against this type of error, it is no longer
and the lockdep code will complain about attempting to unreserve buffers
that are not reserved. The issue is resolved by avoid calling
ttm_eu_backoff_reservation in the buffer reserve error path.
The second issue is that the binding_mutex may be held when user-space
fence objects are created and hence during memory reclaims. This may cause
recursive attempts to grab the binding mutex. The issue is resolved by not
holding the binding mutex across fence creation and submission.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 13 Aug 2015 23:47:07 +0000 (09:47 +1000)]
Merge branch 'exynos-drm-fixes' of git://git./linux/kernel/git/daeinki/drm-exynos into drm-fixes
This pull request fixes memory leak and some issues related to
mixer and gscaler driver issues.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos/fimc: fix runtime pm support
drm/exynos/mixer: always update INT_EN cache
drm/exynos/mixer: correct vsync configuration sequence
drm/exynos/mixer: fix interrupt clearing
drm/exynos/hdmi: fix edid memory leak
drm/exynos: gsc: fix wrong bitwise operation for swap detection
Linus Torvalds [Thu, 13 Aug 2015 23:34:56 +0000 (16:34 -0700)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Another few small ARM fixes, mostly addressing some VDSO issues"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8410/1: VDSO: fix coarse clock monotonicity regression
ARM: 8409/1: Mark ret_fast_syscall as a function
ARM: 8408/1: Fix the secondary_startup function in Big Endian case
ARM: 8405/1: VDSO: fix regression with toolchains lacking ld.bfd executable
Linus Torvalds [Thu, 13 Aug 2015 23:19:44 +0000 (16:19 -0700)]
x86: fix error handling for 32-bit compat out-of-range system call numbers
Commit
3f5159a9221f ("x86/asm/entry/32: Update -ENOSYS handling to match
the 64-bit logic") broke the ENOSYS handling for the 32-bit compat case.
The proper error return value was never loaded into %rax, except if
things just happened to go through the audit paths, which ended up
reloading the return value.
This moves the loading or %rax into the normal system call path, just to
make sure the error case triggers it. It's kind of sad, since it adds a
useless instruction to reload the register to the fast path, but it's
not like that single load from the stack is going to be noticeable.
Reported-by: David Drysdale <drysdale@google.com>
Tested-by: Kees Cook <keescook@chromium.org>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 13 Aug 2015 20:52:46 +0000 (13:52 -0700)]
Merge tag 'dm-4.2-fixes-5' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- two stable fixes for corruption seen in a snapshot of thinp metadata;
metadata snapshots aren't widely used but help provide a consistent
view of the metadata associated with an active thin-pool.
- a dm-cache fix for the 4.2 "default" policy switch from "mq" to "smq"
* tag 'dm-4.2-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache policy smq: move 'dm-cache-default' module alias to SMQ
dm btree: add ref counting ops for the leaves of top level btrees
dm thin metadata: delete btrees when releasing metadata snapshot
Linus Torvalds [Thu, 13 Aug 2015 20:44:32 +0000 (13:44 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull xen block driver fixes from Jens Axboe:
"A few small bug fixes for xen-blk{front,back} that have been sitting
over my vacation"
* 'for-linus' of git://git.kernel.dk/linux-block:
xen-blkback: replace work_pending with work_busy in purge_persistent_gnt()
xen-blkfront: don't add indirect pages to list when !feature_persistent
xen-blkfront: introduce blkfront_gather_backend_features()
Linus Torvalds [Thu, 13 Aug 2015 20:36:22 +0000 (13:36 -0700)]
Merge tag 'for-linus-4.2-rc6-tag' of git://git./linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- revert a fix from 4.2-rc5 that was causing lots of WARNING spam.
- fix a memory leak affecting backends in HVM guests.
- fix PV domU hang with certain configurations.
* tag 'for-linus-4.2-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: Don't leak memory when unmapping the ring on HVM backend
Revert "xen/events/fifo: Handle linked events when closing a port"
x86/xen: build "Xen PV" APIC driver for domU as well
Linus Torvalds [Thu, 13 Aug 2015 15:25:20 +0000 (08:25 -0700)]
Revert x86 sigcontext cleanups
This reverts commits
9a036b93a344 ("x86/signal/64: Remove 'fs' and 'gs'
from sigcontext") and
c6f2062935c8 ("x86/signal/64: Fix SS handling for
signals delivered to 64-bit programs").
They were cleanups, but they break dosemu by changing the signal return
behavior (and removing 'fs' and 'gs' from the sigcontext struct - while
not actually changing any behavior - causes build problems).
Reported-and-tested-by: Stas Sergeev <stsp@list.ru>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 13 Aug 2015 17:46:39 +0000 (10:46 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Workaround hw bug when acquiring PCI bos ownership of iwlwifi
devices, from Emmanuel Grumbach.
2) Falling back to vmalloc in conntrack should not emit a warning, from
Pablo Neira Ayuso.
3) Fix NULL deref when rtlwifi driver is used as an AP, from Luis
Felipe Dominguez Vega.
4) Rocker doesn't free netdev on device removal, from Ido Schimmel.
5) UDP multicast early sock demux has route handling races, from Eric
Dumazet.
6) Fix L4 checksum handling in openvswitch, from Glenn Griffin.
7) Fix use-after-free in skb_set_peeked, from Herbert Xu.
8) Don't advertize NETIF_F_FRAGLIST in virtio_net driver, this can lead
to fraglists longer than the driver can support. From Jason Wang.
9) Fix mlx5 on non-4k-pagesize systems, from Carol L Soto.
10) Fix interrupt storm in bna driver, from Ivan Vecera.
11) Don't propagate -EBUSY from netlink_insert(), from Daniel Borkmann.
12) Fix inet request sock leak, from Eric Dumazet.
13) Fix TX interrupt masking and marking in TX descriptors of fs_enet
driver, from LEROY Christophe.
14) Get rid of rule optimizer in gianfar driver, it's buggy and unlikely
to get fixed any time soon. From Jakub Kicinski
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
cosa: missing error code on failure in probe()
gianfar: remove faulty filer optimizer
gianfar: correct list membership accounting
gianfar: correct filer table writing
bonding: Gratuitous ARP gets dropped when first slave added
net: dsa: Do not override PHY interface if already configured
net: fs_enet: mask interrupts for TX partial frames.
net: fs_enet: explicitly remove I flag on TX partial frames
inet: fix possible request socket leak
inet: fix races with reqsk timers
mkiss: Fix error handling in mkiss_open()
bnx2x: Free NVRAM lock at end of each page
bnx2x: Prevent null pointer dereference on SKB release
cxgb4: missing curly braces in t4_setup_debugfs()
net-timestamp: Update skb_complete_tx_timestamp comment
ipv6: don't reject link-local nexthop on other interface
netlink: make sure -EBUSY won't escape from netlink_insert
bna: fix interrupts storm caused by erroneous packets
net: mvpp2: replace TX coalescing interrupts with hrtimer
net: mvpp2: enable proper per-CPU TX buffers unmapping
...
Linus Torvalds [Thu, 13 Aug 2015 17:22:11 +0000 (10:22 -0700)]
Merge tag 'edac_fix_for_4.2' of git://git./linux/kernel/git/bp/bp
Pull EDAC fix from Borislav Petkov:
"A ppc4xx_edac fix for accessing ->csrows properly. This driver was
missed during the conversion a couple of years ago"
* tag 'edac_fix_for_4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, ppc4xx: Access mci->csrows array elements properly
Murali Karicheri [Mon, 10 Aug 2015 03:06:27 +0000 (20:06 -0700)]
ARM: dts: keystone: Fix the mdio bindings by moving it to soc specific file
Currently mdio bindings are defined in keystone.dtsi and this results
in incorrect unit address for the node on K2E and K2L SoCs. Fix this
by moving them to SoC specific DTS file.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Murali Karicheri [Mon, 10 Aug 2015 03:06:27 +0000 (20:06 -0700)]
ARM: dts: keystone: fix the clock node for mdio
Currently the MDIO clock is pointing to clkpa instead of clkcpgmac.
MDIO is part of the ethss and the clock should be clkcpgmac.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Olof Johansson [Thu, 13 Aug 2015 12:27:12 +0000 (14:27 +0200)]
Merge tag 'omap-for-v4.2/fixes-rc6' of git://git./linux/kernel/git/tmlind/linux-omap into fixes
Fix a NULL pointer exception for omap GPMC bus code if probe fails.
* tag 'omap-for-v4.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
memory: omap-gpmc: Don't try to save uninitialized GPMC context
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Thu, 13 Aug 2015 10:24:55 +0000 (12:24 +0200)]
Merge tag 'imx-fixes-4.2-3' of git://git./linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.2, 3rd round:
- Fix i.MX6 PCIe interrupt routing which gets missed from stacked IRQ
domain conversion. The PCIe wakeup support is currently broken
because of this.
* tag 'imx-fixes-4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6: correct i.MX6 PCIe interrupt routing
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Thu, 13 Aug 2015 10:18:45 +0000 (12:18 +0200)]
Merge tag 'samsung-mach-fixes-4.2' of https://github.com/krzk/linux into fixes
Two fixes for bugs in Exynos power domain error exit path:
1. kfree() of read-only memory (name of power domain returned
by kstrdup_const()),
2. Doubled of_node_put() leading to invalid ref count for OF node.
* tag 'samsung-mach-fixes-4.2' of https://github.com/krzk/linux:
ARM: EXYNOS: fix double of_node_put() on error path
ARM: EXYNOS: Fix potentian kfree() of ro memory
Signed-off-by: Olof Johansson <olof@lixom.net>
Michael Walle [Tue, 21 Jul 2015 09:00:53 +0000 (11:00 +0200)]
EDAC, ppc4xx: Access mci->csrows array elements properly
The commit
de3910eb79ac ("edac: change the mem allocation scheme to
make Documentation/kobject.txt happy")
changed the memory allocation for the csrows member. But ppc4xx_edac was
forgotten in the patch. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: <stable@vger.kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Link: http://lkml.kernel.org/r/1437469253-8611-1-git-send-email-michael@walle.cc
Signed-off-by: Borislav Petkov <bp@suse.de>
Dan Carpenter [Wed, 12 Aug 2015 21:08:01 +0000 (00:08 +0300)]
cosa: missing error code on failure in probe()
If register_hdlc_device() fails, the current code returns 0 but we
should return an error code instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 12 Aug 2015 21:47:06 +0000 (14:47 -0700)]
Merge branch 'gianfar-fixes'
Jakub Kicinski says:
====================
gianfar: filer changes
respinning with examples as requested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 12 Aug 2015 00:41:57 +0000 (02:41 +0200)]
gianfar: remove faulty filer optimizer
Current filer rule optimization is broken in several ways:
(1) Can perform reads/writes beyond end of allocated tables.
(gianfar_ethtool.c:1326).
(2) It breaks badly for rules with more than 2 specifiers
(e.g. matching ip, port, tos).
Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 tos 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 tos 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 tos 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK ==
00000210 AND Q:00 ctrl:
00000080 prop:
00000210
01: FPR ==
00000210 AND CLE Q:00 ctrl:
00000281 prop:
00000210
02: MASK ==
ffffffff AND Q:00 ctrl:
00000080 prop:
ffffffff
03: DPT ==
00000003 AND Q:00 ctrl:
0000008e prop:
00000003
04: TOS ==
00000003 AND Q:00 ctrl:
0000008a prop:
00000003
05: DIA ==
0a000003 AND Q:11 ctrl:
0000448c prop:
0a000003
06: DPT ==
00000002 AND Q:00 ctrl:
0000008e prop:
00000002
07: TOS ==
00000002 AND Q:00 ctrl:
0000008a prop:
00000002
08: DIA ==
0a000002 AND Q:09 ctrl:
0000248c prop:
0a000002
09: DIA ==
0a000001 AND Q:00 ctrl:
0000008c prop:
0a000001
0a: DPT ==
00000001 AND Q:00 ctrl:
0000008e prop:
00000001
0b: TOS ==
00000001 CLE Q:01 ctrl:
0000060a prop:
00000001
ff: MASK >=
00000000 Q:00 ctrl:
00000020 prop:
00000000
(Entire cluster gets AND-ed together).
(3) We observed that the masking rules it generates do not
play well with clustering on P2020. Only first rule
of the cluster would ever fire. Given that optimizer
relies heavily on masking this is very hard to fix.
Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK ==
00000210 AND Q:00 ctrl:
00000080 prop:
00000210
01: FPR ==
00000210 AND CLE Q:00 ctrl:
00000281 prop:
00000210
02: MASK ==
ffffffff AND Q:00 ctrl:
00000080 prop:
ffffffff
03: DPT ==
00000003 AND Q:00 ctrl:
0000008e prop:
00000003
04: DIA ==
0a000003 Q:11 ctrl:
0000440c prop:
0a000003
05: DPT ==
00000002 AND Q:00 ctrl:
0000008e prop:
00000002
06: DIA ==
0a000002 Q:09 ctrl:
0000240c prop:
0a000002
07: DIA ==
0a000001 AND Q:00 ctrl:
0000008c prop:
0a000001
08: DPT ==
00000001 CLE Q:01 ctrl:
0000060e prop:
00000001
ff: MASK >=
00000000 Q:00 ctrl:
00000020 prop:
00000000
Which looks correct according to the spec but only the first
(eth id 252)/last added rule for 10.0.0.3 will ever trigger.
As if filer did not treat the AND CLE as cluster start but
also kept AND-ing the rules. We found no errata covering this.
The fact that nobody noticed (2) or (3) makes me think
that this feature is not very widely used and we should just
remove it.
Reported-by: Aleksander Dutkowski <adutkowski@gmail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 12 Aug 2015 00:41:56 +0000 (02:41 +0200)]
gianfar: correct list membership accounting
At a cost of one line let's make sure .count is correct
when calling gfar_process_filer_changes().
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 12 Aug 2015 00:41:55 +0000 (02:41 +0200)]
gianfar: correct filer table writing
MAX_FILER_IDX is the last usable index. Using less-than
will already guarantee that one entry for catch-all rule
will be left, no need to subtract 1 here.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Venkat Venkatsubra [Tue, 11 Aug 2015 14:57:23 +0000 (07:57 -0700)]
bonding: Gratuitous ARP gets dropped when first slave added
When the first slave is added (such as during bootup) the first
gratuitous ARP gets dropped. We don't see this drop during a failover.
The packet gets dropped in qdisc (noop_enqueue).
The fix is to delay the sending of gratuitous ARPs till the bond dev's
carrier is present.
It can also be worked around by setting num_grat_arp to more than 1.
Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sat, 8 Aug 2015 19:58:57 +0000 (12:58 -0700)]
net: dsa: Do not override PHY interface if already configured
In case we need to divert reads/writes using the slave MII bus, we may have
already fetched a valid PHY interface property from Device Tree, and that
mode is used by the PHY driver to make configuration decisions.
If we could not fetch the "phy-mode" property, we will assign p->phy_interface
to PHY_INTERFACE_MODE_NA, such that we can actually check for that condition as
to whether or not we should override the interface value.
Fixes:
19334920eaf7 ("net: dsa: Set valid phy interface type")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin K. Petersen [Tue, 23 Jun 2015 16:13:59 +0000 (12:13 -0400)]
sd: Fix maximum I/O size for BLOCK_PC requests
Commit
bcdb247c6b6a ("sd: Limit transfer length") clamped the maximum
size of an I/O request to the MAXIMUM TRANSFER LENGTH field in the BLOCK
LIMITS VPD. This had the unfortunate effect of also limiting the maximum
size of non-filesystem requests sent to the device through sg/bsg.
Avoid using blk_queue_max_hw_sectors() and set the max_sectors queue
limit directly.
Also update the comment in blk_limits_max_hw_sectors() to clarify that
max_hw_sectors defines the limit for the I/O controller only.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Brian King <brking@linux.vnet.ibm.com>
Tested-by: Brian King <brking@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Linus Torvalds [Wed, 12 Aug 2015 18:25:01 +0000 (11:25 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fix from Catalin Marinas:
"Fix coarse clock monotonicity (VDSO timestamp off by one jiffy
compared to the syscall one)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: VDSO: fix coarse clock monotonicity regression
Bart Van Assche [Fri, 5 Jun 2015 21:20:51 +0000 (14:20 -0700)]
libfc: Fix fc_fcp_cleanup_each_cmd()
Since fc_fcp_cleanup_cmd() can sleep this function must not
be called while holding a spinlock. This patch avoids that
fc_fcp_cleanup_each_cmd() triggers the following bug:
BUG: scheduling while atomic: sg_reset/1512/0x00000202
1 lock held by sg_reset/1512:
#0: (&(&fsp->scsi_pkt_lock)->rlock){+.-...}, at: [<
ffffffffc0225cd5>] fc_fcp_cleanup_each_cmd.isra.21+0xa5/0x150 [libfc]
Preemption disabled at:[<
ffffffffc0225cd5>] fc_fcp_cleanup_each_cmd.isra.21+0xa5/0x150 [libfc]
Call Trace:
[<
ffffffff816c612c>] dump_stack+0x4f/0x7b
[<
ffffffff810828bc>] __schedule_bug+0x6c/0xd0
[<
ffffffff816c87aa>] __schedule+0x71a/0xa10
[<
ffffffff816c8ad2>] schedule+0x32/0x80
[<
ffffffffc0217eac>] fc_seq_set_resp+0xac/0x100 [libfc]
[<
ffffffffc0218b11>] fc_exch_done+0x41/0x60 [libfc]
[<
ffffffffc0225cff>] fc_fcp_cleanup_each_cmd.isra.21+0xcf/0x150 [libfc]
[<
ffffffffc0225f43>] fc_eh_device_reset+0x1c3/0x270 [libfc]
[<
ffffffff814a2cc9>] scsi_try_bus_device_reset+0x29/0x60
[<
ffffffff814a3908>] scsi_ioctl_reset+0x258/0x2d0
[<
ffffffff814a2650>] scsi_ioctl+0x150/0x440
[<
ffffffff814b3a9d>] sd_ioctl+0xad/0x120
[<
ffffffff8132f266>] blkdev_ioctl+0x1b6/0x810
[<
ffffffff811da608>] block_ioctl+0x38/0x40
[<
ffffffff811b4e08>] do_vfs_ioctl+0x2f8/0x530
[<
ffffffff811b50c1>] SyS_ioctl+0x81/0xa0
[<
ffffffff816cf8b2>] system_call_fastpath+0x16/0x7a
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Bart Van Assche [Fri, 5 Jun 2015 21:20:46 +0000 (14:20 -0700)]
libfc: Fix fc_exch_recv_req() error path
Due to patch "libfc: Do not invoke the response handler after
fc_exch_done()" (commit ID
7030fd62) the lport_recv() call
in fc_exch_recv_req() is passed a dangling pointer. Avoid this
by moving the fc_frame_free() call from fc_invoke_resp() to its
callers. This patch fixes the following crash:
general protection fault: 0000 [#3] PREEMPT SMP
RIP: fc_lport_recv_req+0x72/0x280 [libfc]
Call Trace:
fc_exch_recv+0x642/0xde0 [libfc]
fcoe_percpu_receive_thread+0x46a/0x5ed [fcoe]
kthread+0x10a/0x120
ret_from_fork+0x42/0x70
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Linus Torvalds [Wed, 12 Aug 2015 18:13:54 +0000 (11:13 -0700)]
Merge branch 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux
Pull amd drm fixes from Alex Deucher:
"Dave is on vacation at the moment, so please pull these radeon and
amdgpu fixes directly.
Just a few minor things for 4.2:
- add a new radeon pci id
- fix a power management regression in amdgpu
- fix HEVC command buffer validation in amdgpu"
* 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add new OLAND pci id
Revert "drm/amdgpu: Configure doorbell to maximum slots"
drm/amdgpu: add context buffer size check for HEVC
John Soni Jose [Wed, 24 Jun 2015 01:11:58 +0000 (06:41 +0530)]
libiscsi: Fix host busy blocking during connection teardown
In case of hw iscsi offload, an host can have N-number of active
connections. There can be IO's running on some connections which
make host->host_busy always TRUE. Now if logout from a connection
is tried then the code gets into an infinite loop as host->host_busy
is always TRUE.
iscsi_conn_teardown(....)
{
.........
/*
* Block until all in-progress commands for this connection
* time out or fail.
*/
for (;;) {
spin_lock_irqsave(session->host->host_lock, flags);
if (!atomic_read(&session->host->host_busy)) { /* OK for ERL == 0 */
spin_unlock_irqrestore(session->host->host_lock, flags);
break;
}
spin_unlock_irqrestore(session->host->host_lock, flags);
msleep_interruptible(500);
iscsi_conn_printk(KERN_INFO, conn, "iscsi conn_destroy(): "
"host_busy %d host_failed %d\n",
atomic_read(&session->host->host_busy),
session->host->host_failed);
................
...............
}
}
This is not an issue with software-iscsi/iser as each cxn is a separate
host.
Fix:
Acquiring eh_mutex in iscsi_conn_teardown() before setting
session->state = ISCSI_STATE_TERMINATE.
Signed-off-by: John Soni Jose <sony.john@avagotech.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Chris Leech <cleech@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Alex Deucher [Mon, 10 Aug 2015 19:28:49 +0000 (15:28 -0400)]
drm/radeon: add new OLAND pci id
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Alex Deucher [Mon, 10 Aug 2015 15:08:31 +0000 (11:08 -0400)]
Revert "drm/amdgpu: Configure doorbell to maximum slots"
This reverts commit
78ad5cdd21f0d614983fc397338944e797ec70b9.
This commit breaks dpm and suspend/resume on CZ.
Boyuan Zhang [Wed, 5 Aug 2015 18:03:48 +0000 (14:03 -0400)]
drm/amdgpu: add context buffer size check for HEVC
Signed-off-by: Boyuan Zhang <boyuan.zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Linus Torvalds [Wed, 12 Aug 2015 16:06:39 +0000 (09:06 -0700)]
Merge tag 'regmap-fix-v4.2-rc6' of git://git./linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"regmap: Fix handling of present bits on rbtree cache block resize
When expanding a cache block we use krealloc() to resize the register
present bitmap without initialising the newly allocated data (the
original code was written for kzalloc()). Add an appropraite memset()
to fix that"
* tag 'regmap-fix-v4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: regcache-rbtree: Clean new present bits on present bitmap resize
Yi Zhang [Wed, 12 Aug 2015 11:22:43 +0000 (19:22 +0800)]
dm cache policy smq: move 'dm-cache-default' module alias to SMQ
When creating dm-cache with the default policy, it will call
request_module("dm-cache-default") to register the default policy.
But the "dm-cache-default" alias was left referring to the MQ policy.
Fix this by moving the module alias to SMQ.
Fixes:
bccab6a0 (dm cache: switch the "default" cache replacement policy from mq to smq)
Signed-off-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Joe Thornber [Wed, 12 Aug 2015 14:12:09 +0000 (15:12 +0100)]
dm btree: add ref counting ops for the leaves of top level btrees
When using nested btrees, the top leaves of the top levels contain
block addresses for the root of the next tree down. If we shadow a
shared leaf node the leaf values (sub tree roots) should be incremented
accordingly.
This is only an issue if there is metadata sharing in the top levels.
Which only occurs if metadata snapshots are being used (as is possible
with dm-thinp). And could result in a block from the thinp metadata
snap being reused early, thus corrupting the thinp metadata snap.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Joe Thornber [Wed, 12 Aug 2015 14:10:21 +0000 (15:10 +0100)]
dm thin metadata: delete btrees when releasing metadata snapshot
The device details and mapping trees were just being decremented
before. Now btree_del() is called to do a deep delete.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Matt Fleming [Thu, 6 Aug 2015 12:12:43 +0000 (13:12 +0100)]
perf/x86/intel/cqm: Do not access cpu_data() from CPU_UP_PREPARE handler
Tony reports that booting his 144-cpu machine with maxcpus=10 triggers
the following WARN_ON():
[ 21.045727] WARNING: CPU: 8 PID: 647 at arch/x86/kernel/cpu/perf_event_intel_cqm.c:1267 intel_cqm_cpu_prepare+0x75/0x90()
[ 21.045744] CPU: 8 PID: 647 Comm: systemd-udevd Not tainted 4.2.0-rc4 #1
[ 21.045745] Hardware name: Intel Corporation BRICKLAND/BRICKLAND, BIOS BRHSXSD1.86B.0066.R00.
1506021730 06/02/2015
[ 21.045747]
0000000000000000 0000000082771b09 ffff880856333ba8 ffffffff81669b67
[ 21.045748]
0000000000000000 0000000000000000 ffff880856333be8 ffffffff8107b02a
[ 21.045750]
ffff88085b789800 ffff88085f68a020 ffffffff819e2470 000000000000000a
[ 21.045750] Call Trace:
[ 21.045757] [<
ffffffff81669b67>] dump_stack+0x45/0x57
[ 21.045759] [<
ffffffff8107b02a>] warn_slowpath_common+0x8a/0xc0
[ 21.045761] [<
ffffffff8107b15a>] warn_slowpath_null+0x1a/0x20
[ 21.045762] [<
ffffffff81036725>] intel_cqm_cpu_prepare+0x75/0x90
[ 21.045764] [<
ffffffff81036872>] intel_cqm_cpu_notifier+0x42/0x160
[ 21.045767] [<
ffffffff8109a33d>] notifier_call_chain+0x4d/0x80
[ 21.045769] [<
ffffffff8109a44e>] __raw_notifier_call_chain+0xe/0x10
[ 21.045770] [<
ffffffff8107b538>] _cpu_up+0xe8/0x190
[ 21.045771] [<
ffffffff8107b65a>] cpu_up+0x7a/0xa0
[ 21.045774] [<
ffffffff8165e920>] cpu_subsys_online+0x40/0x90
[ 21.045777] [<
ffffffff81433b37>] device_online+0x67/0x90
[ 21.045778] [<
ffffffff81433bea>] online_store+0x8a/0xa0
[ 21.045782] [<
ffffffff81430e78>] dev_attr_store+0x18/0x30
[ 21.045785] [<
ffffffff8126b6ba>] sysfs_kf_write+0x3a/0x50
[ 21.045786] [<
ffffffff8126ad40>] kernfs_fop_write+0x120/0x170
[ 21.045789] [<
ffffffff811f0b77>] __vfs_write+0x37/0x100
[ 21.045791] [<
ffffffff811f38b8>] ? __sb_start_write+0x58/0x110
[ 21.045795] [<
ffffffff81296d2d>] ? security_file_permission+0x3d/0xc0
[ 21.045796] [<
ffffffff811f1279>] vfs_write+0xa9/0x190
[ 21.045797] [<
ffffffff811f2075>] SyS_write+0x55/0xc0
[ 21.045800] [<
ffffffff81067300>] ? do_page_fault+0x30/0x80
[ 21.045804] [<
ffffffff816709ae>] entry_SYSCALL_64_fastpath+0x12/0x71
[ 21.045805] ---[ end trace
fe228b836d8af405 ]---
The root cause is that CPU_UP_PREPARE is completely the wrong notifier
action from which to access cpu_data(), because smp_store_cpu_info()
won't have been executed by the target CPU at that point, which in turn
means that ->x86_cache_max_rmid and ->x86_cache_occ_scale haven't been
filled out.
Instead let's invoke our handler from CPU_STARTING and rename it
appropriately.
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Kanaka Juvva <kanaka.d.juvva@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vikas Shivappa <vikas.shivappa@intel.com>
Link: http://lkml.kernel.org/r/1438863163-14083-1-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Zijlstra [Mon, 10 Aug 2015 12:17:34 +0000 (14:17 +0200)]
perf/x86/intel: Fix memory leak on hot-plug allocation fail
We fail to free the shared_regs allocation if the constraint_list
allocation fails.
Cure this and be more consistent in NULL-ing the pointers after free.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Zijlstra [Tue, 4 Aug 2015 17:22:49 +0000 (19:22 +0200)]
perf: Fix PERF_EVENT_IOC_PERIOD migration race
I ran the perf fuzzer, which triggered some WARN()s which are due to
trying to stop/restart an event on the wrong CPU.
Use the normal IPI pattern to ensure we run the code on the correct CPU.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes:
bad7192b842c ("perf: Fix PERF_EVENT_IOC_PERIOD to force-reset the period")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ben Hutchings [Sun, 26 Jul 2015 23:31:08 +0000 (00:31 +0100)]
perf: Fix double-free of the AUX buffer
If rb->aux_refcount is decremented to zero before rb->refcount,
__rb_free_aux() may be called twice resulting in a double free of
rb->aux_pages. Fix this by adding a check to __rb_free_aux().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes:
57ffc5ca679f ("perf: Fix AUX buffer refcounting")
Link: http://lkml.kernel.org/r/1437953468.12842.17.camel@decadent.org.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tomeu Vizoso [Wed, 5 Aug 2015 12:24:15 +0000 (14:24 +0200)]
memory: omap-gpmc: Don't try to save uninitialized GPMC context
If for some reason the GPMC device hasn't been probed yet, gpmc_base is
going to be NULL. Because there's no context yet to be saved, just turn
these functions into no-ops until that device gets probed.
Unable to handle kernel NULL pointer dereference at virtual address
00000010
pgd =
c0204000
[
00000010] *pgd=
00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted
4.2.0-rc5-next-20150804-05947-g23f38fe8eda9 #1
Hardware name: Generic OMAP3-GP (Flattened Device Tree)
task:
c0e623e8 ti:
c0e5c000 task.ti:
c0e5c000
PC is at omap3_gpmc_save_context+0x8/0xc4
LR is at omap_sram_idle+0x154/0x23c
pc : [<
c087c7ac>] lr : [<
c023262c>] psr:
60000193
sp :
c0e5df40 ip :
c0f92a80 fp :
c0999eb0
r10:
c0e57364 r9 :
c0e66f14 r8 :
00000003
r7 :
00000000 r6 :
00000003 r5 :
00000000 r4 :
c0f5f174
r3 :
c0fa4fe8 r2 :
00000000 r1 :
00000000 r0 :
fa200280
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control:
10c5387d Table:
80204019 DAC:
00000015
Process swapper/0 (pid: 0, stack limit = 0xc0e5c220)
Stack: (0xc0e5df40 to 0xc0e5e000)
df40:
00000000 c0e66ef8 c0f5f1a4 00000000 00000003 c02333a4 c3813822 00000000
df60:
00000000 c0e5a5c8 cfb8a5d0 c07f0c44 0e4f1d7e 00000000 00000000 00000000
df80:
c3813822 00000000 cfb8a5d0 c0e5e4e4 cfb8a5d0 c0e66f14 c0e5a5c8 c0e5e54c
dfa0:
c0e5e544 c0e57364 c0999eb0 c0277758 000000fa c0f5d000 00000000 c0d61c18
dfc0:
ffffffff ffffffff 00000000 c0d61674 00000000 c0df7a48 00000000 c0f5d5d4
dfe0:
c0e5e4c0 c0df7a44 c0e634f8 80204059 00000000 8020807c 00000000 00000000
[<
c087c7ac>] (omap3_gpmc_save_context) from [<
c023262c>] (omap_sram_idle+0x154/0x23c)
[<
c023262c>] (omap_sram_idle) from [<
c02333a4>] (omap3_enter_idle_bm+0xec/0x1a8)
[<
c02333a4>] (omap3_enter_idle_bm) from [<
c07f0c44>] (cpuidle_enter_state+0xbc/0x284)
[<
c07f0c44>] (cpuidle_enter_state) from [<
c0277758>] (cpu_startup_entry+0x174/0x24c)
[<
c0277758>] (cpu_startup_entry) from [<
c0d61c18>] (start_kernel+0x358/0x3c0)
[<
c0d61c18>] (start_kernel) from [<
8020807c>] (0x8020807c)
Code:
c0ccace8 c0ccacc0 e59f30b4 e5932000 (
e5921010)
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Suggested-by: Javier Martinez Canillas <javier@dowhile0.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Roger Quadros <rogerq@ti.com>
[tony@atomide.com: updated description as suggested by Javier]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Tue, 11 Aug 2015 22:13:41 +0000 (15:13 -0700)]
Merge tag 'localmodconfig-v4.2-rc6' of git://git./linux/kernel/git/rostedt/linux-kconfig
Pull localmodconfig fix from Steven Rostedt:
"Leonidas Spyropoulos found that modules like nouveau were being
unselected by make localmodconfig even though their configs were set
and the module was loaded and visible by lsmod.
The reason for this was because streamline-config.pl only looks at
Makefiles, and not Kbuild files. As these modules use Kbuild for
their names, they too need to be checked by localmodconfig. This was
fixed by Richard Weinberger"
* tag 'localmodconfig-v4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-kconfig:
localmodconfig: Use Kbuild files too
Richard Weinberger [Sun, 26 Jul 2015 22:06:55 +0000 (00:06 +0200)]
localmodconfig: Use Kbuild files too
In kbuild it is allowed to define objects in files named "Makefile"
and "Kbuild".
Currently localmodconfig reads objects only from "Makefile"s and misses
modules like nouveau.
Link: http://lkml.kernel.org/r/1437948415-16290-1-git-send-email-richard@nod.at
Cc: stable@vger.kernel.org
Reported-and-tested-by: Leonidas Spyropoulos <artafinde@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
David S. Miller [Tue, 11 Aug 2015 21:16:07 +0000 (14:16 -0700)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2015-08-11
Here's an important regression fix for the 4.2-rc series that ensures
user space isn't given invalid LTK values. The bug essentially prevents
the encryption of subsequent LE connections, i.e. makes it impossible to
pair devices over LE.
Let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
LEROY Christophe [Tue, 11 Aug 2015 10:11:03 +0000 (12:11 +0200)]
net: fs_enet: mask interrupts for TX partial frames.
We are not interested in interrupts for partially transmitted frames.
Unlike SCC and FCC, the FEC doesn't handle the I bit in buffer
descriptors, instead it defines two interrupt bits, TXB and TXF.
We have to mask TXB in order to only get interrupts once the
frame is fully transmitted.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
LEROY Christophe [Tue, 11 Aug 2015 10:11:00 +0000 (12:11 +0200)]
net: fs_enet: explicitly remove I flag on TX partial frames
We are not interested in interrupts for partially transmitted frames,
we have to clear BD_ENET_TX_INTR explicitly otherwise it may remain
from a previously used descriptor.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 11 Aug 2015 17:23:59 +0000 (10:23 -0700)]
Merge tag 'fbdev-fixes-4.2' of git://git./linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- fix display regression on Versatile boards
- fix OF node refcount bugs on omapdss
- fix WARN about clock prepare on pxa3xx_gcu
- fix mem leak in videomode helpers
- fix fbconsole related boot problem on sun7i-a20-olinuxino-micro
* tag 'fbdev-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
fbcon: unconditionally initialize cursor blink interval
video: Fix possible leak in of_get_videomode()
video: fbdev: pxa3xx_gcu: prepare the clocks
OMAPDSS: Fix omap_dss_find_output_by_port_node() port refcount decrement
OMAPDSS: Fix node refcount leak in omapdss_of_get_next_port()
fbdev: select versatile helpers for the integrator