OSDN Git Service
Andrew Lunn [Thu, 9 Nov 2017 22:11:01 +0000 (23:11 +0100)]
net: dsa: add more const attributes
The notify mechanism does not need to modify the port it is notifying.
So make the parameter const.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 9 Nov 2017 22:11:00 +0000 (23:11 +0100)]
net: dsa: slave: Handle switchdev host mdb add/del
Add code to handle switchdev host mdb add/del. Since DSA uses one of
the switch ports as a transport to the host, we just need to add an
MDB on this port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 9 Nov 2017 22:10:59 +0000 (23:10 +0100)]
net: bridge: Add/del switchdev object on host join/leave
When the host joins or leaves a multicast group, use switchdev to add
an object to the hardware to forward traffic for the group to the
host.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 9 Nov 2017 22:10:58 +0000 (23:10 +0100)]
net: bridge: Send notification when host join/leaves a group
The host can join or leave a multicast group on the brX interface, as
indicated by IGMP snooping. This is tracked within the bridge
multicast code. Send a notification when this happens, in the same way
a notification is sent when a port of the bridge joins/leaves a group
because of IGMP snooping.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 9 Nov 2017 22:10:57 +0000 (23:10 +0100)]
net: bridge: Rename mglist to host_joined
The boolean mglist indicates the host has joined a particular
multicast group on the bridge interface. It is badly named, obscuring
what is means. Rename it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 10 Nov 2017 01:00:18 +0000 (10:00 +0900)]
Merge git://git./linux/kernel/git/davem/net
Simple cases of overlapping changes in the packet scheduler.
Must easier to resolve this time.
Which probably means that I screwed it up somehow.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 9 Nov 2017 19:16:28 +0000 (11:16 -0800)]
Merge tag 'pm-final-4.14' of git://git./linux/kernel/git/rafael/linux-pm
Pull final power management fixes from Rafael Wysocki:
"These fix a regression in the schedutil cpufreq governor introduced by
a recent change and blacklist Dell XPS13 9360 from using the Low Power
S0 Idle _DSM interface which triggers serious problems on one of these
machines.
Specifics:
- Prevent the schedutil cpufreq governor from using the utilization
of a wrong CPU in some cases which started to happen after one of
the recent changes in it (Chris Redpath).
- Blacklist Dell XPS13 9360 from using the Low Power S0 Idle _DSM
interface as that causes serious issue (related to NVMe) to appear
on one of these machines, even though the other Dells XPS13 9360 in
somewhat different HW configurations behave correctly (Rafael
Wysocki)"
* tag 'pm-final-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Blacklist Low Power S0 Idle _DSM for Dell XPS13 9360
cpufreq: schedutil: Examine the correct CPU when we update util
Linus Torvalds [Thu, 9 Nov 2017 17:58:11 +0000 (09:58 -0800)]
Merge tag 'sound-4.14' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The amount of the changes isn't as quite small as wished, nevertheless
they are straight fixes that deserve merging to 4.14 final.
Most of fixes are about ALSA core bugs spotted by fuzzer: a follow-up
fix for the previous nested rwsem patch, a fix to avoid the resource
hogs due to too many concurrent ALSA timer invocations, and a fix for
a crash with SYSEX MIDI transfer over OSS sequencer emulation that is
used by none but fuzzer.
The rest are usual HD-audio and USB-audio device-specific quirks,
which are safe to apply"
* tag 'sound-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - fix headset mic problem for Dell machines with alc274
ALSA: seq: Fix OSS sysex delivery in OSS emulation
ALSA: seq: Avoid invalid lockdep class warning
ALSA: timer: Limit max instances per timer
ALSA: usb-audio: support new Amanero Combo384 firmware version
Linus Torvalds [Thu, 9 Nov 2017 17:31:34 +0000 (09:31 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix use-after-free in IPSEC input parsing, desintation address
pointer was loaded before pskb_may_pull() which can change the SKB
data pointers. From Florian Westphal.
2) Stack out-of-bounds read in xfrm_state_find(), from Steffen
Klassert.
3) IPVS state of SKB is not properly reset when moving between
namespaces, from Ye Yin.
4) Fix crash in asix driver suspend and resume, from Andrey Konovalov.
5) Don't deliver ipv6 l2tp tunnel packets to ipv4 l2tp tunnels, and
vice versa, from Guillaume Nault.
6) Fix DSACK undo on non-dup ACKs, from Priyaranjan Jha.
7) Fix regression in bond_xmit_hash()'s behavior after the TCP port
selection changes back in 4.2, from Hangbin Liu.
8) Two divide by zero bugs in USB networking drivers when parsing
descriptors, from Bjorn Mork.
9) Fix bonding slaves being stuck in BOND_LINK_FAIL state, from Jay
Vosburgh.
10) Missing skb_reset_mac_header() in qmi_wwan, from Kristian Evensen.
11) Fix the destruction of tc action object races properly, from Cong
Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (31 commits)
cls_u32: use tcf_exts_get_net() before call_rcu()
cls_tcindex: use tcf_exts_get_net() before call_rcu()
cls_rsvp: use tcf_exts_get_net() before call_rcu()
cls_route: use tcf_exts_get_net() before call_rcu()
cls_matchall: use tcf_exts_get_net() before call_rcu()
cls_fw: use tcf_exts_get_net() before call_rcu()
cls_flower: use tcf_exts_get_net() before call_rcu()
cls_flow: use tcf_exts_get_net() before call_rcu()
cls_cgroup: use tcf_exts_get_net() before call_rcu()
cls_bpf: use tcf_exts_get_net() before call_rcu()
cls_basic: use tcf_exts_get_net() before call_rcu()
net_sched: introduce tcf_exts_get_net() and tcf_exts_put_net()
Revert "net_sched: hold netns refcnt for each action"
net: usb: asix: fill null-ptr-deref in asix_suspend
Revert "net: usb: asix: fill null-ptr-deref in asix_suspend"
qmi_wwan: Add missing skb_reset_mac_header-call
bonding: fix slave stuck in BOND_LINK_FAIL state
qrtr: Move to postcore_initcall
net: qmi_wwan: fix divide by 0 on bad descriptors
net: cdc_ether: fix divide by 0 on bad descriptors
...
Hui Wang [Thu, 9 Nov 2017 00:48:08 +0000 (08:48 +0800)]
ALSA: hda - fix headset mic problem for Dell machines with alc274
Confirmed with Kailang of Realtek, the pin 0x19 is for Headset Mic, and
the pin 0x1a is for Headphone Mic, he suggested to apply
ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to fix this problem. And we
verified applying this FIXUP can fix this problem.
Cc: <stable@vger.kernel.org>
Cc: Kailang Yang <kailang@realtek.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
David S. Miller [Thu, 9 Nov 2017 01:58:35 +0000 (10:58 +0900)]
Merge branch 'master' of git://git./linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2017-11-09
1) Fix a use after free due to a reallocated skb head.
From Florian Westphal.
2) Fix sporadic lookup failures on labeled IPSEC.
From Florian Westphal.
3) Fix a stack out of bounds when a socket policy is applied
to an IPv6 socket that sends IPv4 packets.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 9 Nov 2017 01:03:10 +0000 (10:03 +0900)]
Merge branch 'net-sched-race-fix'
Cong Wang says:
====================
net_sched: close the race between call_rcu() and cleanup_net()
This patchset tries to fix the race between call_rcu() and
cleanup_net() again. Without holding the netns refcnt the
tc_action_net_exit() in netns workqueue could be called before
filter destroy works in tc filter workqueue. This patchset
moves the netns refcnt from tc actions to tcf_exts, without
breaking per-netns tc actions.
Patch 1 reverts the previous fix, patch 2 introduces two new
API's to help to address the bug and the rest patches switch
to the new API's. Please see each patch for details.
I was not able to reproduce this bug, but now after adding
some delay in filter destroy work I manage to trigger the
crash. After this patchset, the crash is not reproducible
any more and the debugging printk's show the order is expected
too.
====================
Fixes:
ddf97ccdd7cb ("net_sched: add network namespace support for tc actions")
Reported-by: Lucas Bates <lucasb@mojatatu.com>
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:30 +0000 (13:47 -0800)]
cls_u32: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:29 +0000 (13:47 -0800)]
cls_tcindex: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:28 +0000 (13:47 -0800)]
cls_rsvp: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:27 +0000 (13:47 -0800)]
cls_route: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:26 +0000 (13:47 -0800)]
cls_matchall: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:25 +0000 (13:47 -0800)]
cls_fw: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:24 +0000 (13:47 -0800)]
cls_flower: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:23 +0000 (13:47 -0800)]
cls_flow: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:22 +0000 (13:47 -0800)]
cls_cgroup: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:21 +0000 (13:47 -0800)]
cls_bpf: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:20 +0000 (13:47 -0800)]
cls_basic: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:19 +0000 (13:47 -0800)]
net_sched: introduce tcf_exts_get_net() and tcf_exts_put_net()
Instead of holding netns refcnt in tc actions, we can minimize
the holding time by saving it in struct tcf_exts instead. This
means we can just hold netns refcnt right before call_rcu() and
release it after tcf_exts_destroy() is done.
However, because on netns cleanup path we call tcf_proto_destroy()
too, obviously we can not hold netns for a zero refcnt, in this
case we have to do cleanup synchronously. It is fine for RCU too,
the caller cleanup_net() already waits for a grace period.
For other cases, refcnt is non-zero and we can safely grab it as
normal and release it after we are done.
This patch provides two new API for each filter to use:
tcf_exts_get_net() and tcf_exts_put_net(). And all filters now can
use the following pattern:
void __destroy_filter() {
tcf_exts_destroy();
tcf_exts_put_net(); // <== release netns refcnt
kfree();
}
void some_work() {
rtnl_lock();
__destroy_filter();
rtnl_unlock();
}
void some_rcu_callback() {
tcf_queue_work(some_work);
}
if (tcf_exts_get_net()) // <== hold netns refcnt
call_rcu(some_rcu_callback);
else
__destroy_filter();
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:18 +0000 (13:47 -0800)]
Revert "net_sched: hold netns refcnt for each action"
This reverts commit
ceffcc5e254b450e6159f173e4538215cebf1b59.
If we hold that refcnt, the netns can never be destroyed until
all actions are destroyed by user, this breaks our netns design
which we expect all actions are destroyed when we destroy the
whole netns.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 9 Nov 2017 00:26:50 +0000 (09:26 +0900)]
Merge branch 'dsa-setup-stage'
Vivien Didelot says:
====================
net: dsa: setup stage
When probing a DSA switch, there is basically two stages.
The first stage is the parsing of the switch device, from either device
tree or platform data. It fetches the DSA tree to which it belongs, and
validates its ports. The switch device is then added to the tree, and
the second stage is called if this was the last switch of the tree.
The second stage is the setup of the tree, which validates that the tree
is complete, sets up the routing tables, the default CPU port for user
ports, sets up the switch drivers and finally the master interfaces,
which makes the whole switch fabric functional.
This patch series covers the second setup stage. The setup and teardown
of a switch tree have been separated into logical steps, and the probing
of a switch now simply parses and adds a switch to a tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 6 Nov 2017 21:11:53 +0000 (16:11 -0500)]
net: dsa: rename probe and remove switch functions
This commit brings no functional changes. It gets rid of the underscore
prefixed _dsa_register_switch and _dsa_unregister_switch functions in
favor of dsa_switch_probe() which parses and adds a switch to a tree and
dsa_switch_remove() which removes a switch from a tree.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 6 Nov 2017 21:11:52 +0000 (16:11 -0500)]
net: dsa: setup a tree when adding a switch to it
Now that the tree setup is centralized, we can simplify the code a bit
more by setting up or tearing down the tree directly when adding or
removing a switch to/from it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 6 Nov 2017 21:11:51 +0000 (16:11 -0500)]
net: dsa: setup routing table
The *_complete() functions take too much arguments to do only one thing:
they try to fetch the dsa_port structures corresponding to device nodes
under the "link" list property of DSA ports, and use them to setup the
routing table of switches.
This patch simplifies them by providing instead simpler
dsa_{port,switch,tree}_setup_routing_table functions which return a
boolean value, true if the tree is complete.
dsa_tree_setup_routing_table is called inside dsa_tree_setup which
simplifies the switch registering function as well.
A switch's routing table is now initialized before its setup.
This also makes dsa_port_is_valid obsolete, remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 6 Nov 2017 21:11:50 +0000 (16:11 -0500)]
net: dsa: use of_for_each_phandle
The OF code provides a of_for_each_phandle() helper to iterate over
phandles. Use it instead of arbitrary iterating ourselves over the list
of phandles hanging to the "link" property of the port's device node.
The of_phandle_iterator_next() helper calls of_node_put() itself on
it.node. Thus We must only do it ourselves if we break the loop.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 6 Nov 2017 21:11:49 +0000 (16:11 -0500)]
net: dsa: add find port by node helper
Instead of having two dsa_ds_find_port_dn (which returns a bool) and
dsa_dst_find_port_dn (which returns a switch) functions, provide a more
explicit dsa_tree_find_port_by_node function which returns a matching
port.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 6 Nov 2017 21:11:48 +0000 (16:11 -0500)]
net: dsa: setup and teardown ports
The dsa_dsa_port_apply and dsa_cpu_port_apply functions do exactly the
same. The dsa_user_port_apply function does not try to register a fixed
link but try to create a slave.
This commit factorizes and scopes all that in two convenient
dsa_port_setup and dsa_port_teardown functions.
It won't hurt to register a devlink_port for unused port as well.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 6 Nov 2017 21:11:47 +0000 (16:11 -0500)]
net: dsa: setup and teardown switches
This patches brings no functional changes. It removes the unused dst
argument from the dsa_ds_apply and dsa_ds_unapply functions, rename them
to dsa_switch_setup and dsa_switch_teardown for a more explicit scope.
This clarifies the steps of the setup or teardown of a switch fabric.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 6 Nov 2017 21:11:46 +0000 (16:11 -0500)]
net: dsa: setup and teardown tree
This commit provides better scope for the DSA tree setup and teardown
functions. It renames the "applied" bool to "setup" and print a message
when the tree is setup, as it is done during teardown.
At the same time, check dst->setup in dsa_tree_setup, where it is set to
true.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 6 Nov 2017 21:11:45 +0000 (16:11 -0500)]
net: dsa: setup and teardown master device
Add DSA helpers to setup and teardown a master net device wired to its
CPU port. This centralizes the dsa_ptr assignment.
This also makes the master ethtool helpers static at the same time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 6 Nov 2017 21:11:44 +0000 (16:11 -0500)]
net: dsa: setup and teardown default CPU port
The dsa_dst_parse function called just before dsa_dst_apply does not
parse the tree but does only one thing: it assigns the default CPU port
to dst->cpu_dp and to each user ports.
This patch simplifies this by calling a dsa_tree_setup_default_cpu
function at the beginning of dsa_dst_apply directly.
A dsa_port_is_user helper is added for convenience.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 6 Nov 2017 21:11:43 +0000 (16:11 -0500)]
net: dsa: constify cpu_dp member of dsa_port
A DSA port has a dedicated CPU port assigned to it, stored in the cpu_dp
member. It is not meant to be modified by a port, thus make it const.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Konovalov [Mon, 6 Nov 2017 12:26:46 +0000 (13:26 +0100)]
net: usb: asix: fill null-ptr-deref in asix_suspend
When asix_suspend() is called dev->driver_priv might not have been
assigned a value, so we need to check that it's not NULL.
Similar issue is present in asix_resume(), this patch fixes it as well.
Found by syzkaller.
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
Modules linked in:
CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted
4.14.0-rc4-43422-geccacdd69a8c #400
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
task:
ffff88006bb36300 task.stack:
ffff88006bba8000
RIP: 0010:asix_suspend+0x76/0xc0 drivers/net/usb/asix_devices.c:629
RSP: 0018:
ffff88006bbae718 EFLAGS:
00010202
RAX:
dffffc0000000000 RBX:
ffff880061ba3b80 RCX:
1ffff1000c34d644
RDX:
0000000000000001 RSI:
0000000000000402 RDI:
0000000000000008
RBP:
ffff88006bbae738 R08:
1ffff1000d775cad R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000000 R12:
ffff8800630a8b40
R13:
0000000000000000 R14:
0000000000000402 R15:
ffff880061ba3b80
FS:
0000000000000000(0000) GS:
ffff88006c600000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007ff33cf89000 CR3:
0000000061c0a000 CR4:
00000000000006f0
Call Trace:
usb_suspend_interface drivers/usb/core/driver.c:1209
usb_suspend_both+0x27f/0x7e0 drivers/usb/core/driver.c:1314
usb_runtime_suspend+0x41/0x120 drivers/usb/core/driver.c:1852
__rpm_callback+0x339/0xb60 drivers/base/power/runtime.c:334
rpm_callback+0x106/0x220 drivers/base/power/runtime.c:461
rpm_suspend+0x465/0x1980 drivers/base/power/runtime.c:596
__pm_runtime_suspend+0x11e/0x230 drivers/base/power/runtime.c:1009
pm_runtime_put_sync_autosuspend ./include/linux/pm_runtime.h:251
usb_new_device+0xa37/0x1020 drivers/usb/core/hub.c:2487
hub_port_connect drivers/usb/core/hub.c:4903
hub_port_connect_change drivers/usb/core/hub.c:5009
port_event drivers/usb/core/hub.c:5115
hub_event+0x194d/0x3740 drivers/usb/core/hub.c:5195
process_one_work+0xc7f/0x1db0 kernel/workqueue.c:2119
worker_thread+0x221/0x1850 kernel/workqueue.c:2253
kthread+0x3a1/0x470 kernel/kthread.c:231
ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:431
Code: 8d 7c 24 20 48 89 fa 48 c1 ea 03 80 3c 02 00 75 5b 48 b8 00 00
00 00 00 fc ff df 4d 8b 6c 24 20 49 8d 7d 08 48 89 fa 48 c1 ea 03 <80>
3c 02 00 75 34 4d 8b 6d 08 4d 85 ed 74 0b e8 26 2b 51 fd 4c
RIP: asix_suspend+0x76/0xc0 RSP:
ffff88006bbae718
---[ end trace
dfc4f5649284342c ]---
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 9 Nov 2017 00:21:44 +0000 (09:21 +0900)]
Revert "net: usb: asix: fill null-ptr-deref in asix_suspend"
This reverts commit
baedf68a068ca29624f241426843635920f16e1d.
There is an updated version of this fix which covers
the problem more thoroughly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafael J. Wysocki [Wed, 8 Nov 2017 23:07:56 +0000 (00:07 +0100)]
Merge branch 'pm-cpufreq-sched'
* pm-cpufreq-sched:
cpufreq: schedutil: Examine the correct CPU when we update util
Jiri Kosina [Wed, 8 Nov 2017 20:18:18 +0000 (21:18 +0100)]
x86/mm: Unbreak modules that rely on external PAGE_KERNEL availability
Commit
7744ccdbc16f0 ("x86/mm: Add Secure Memory Encryption (SME)
support") as a side-effect made PAGE_KERNEL all of a sudden unavailable
to modules which can't make use of EXPORT_SYMBOL_GPL() symbols.
This is because once SME is enabled, sme_me_mask (which is introduced as
EXPORT_SYMBOL_GPL) makes its way to PAGE_KERNEL through _PAGE_ENC,
causing imminent build failure for all the modules which make use of all
the EXPORT-SYMBOL()-exported API (such as vmap(), __vmalloc(),
remap_pfn_range(), ...).
Exporting (as EXPORT_SYMBOL()) interfaces (and having done so for ages)
that take pgprot_t argument, while making it impossible to -- all of a
sudden -- pass PAGE_KERNEL to it, feels rather incosistent.
Restore the original behavior and make it possible to pass PAGE_KERNEL
to all its EXPORT_SYMBOL() consumers.
[ This is all so not wonderful. We shouldn't need that "sme_me_mask"
access at all in all those places that really don't care about that
level of detail, and just want _PAGE_KERNEL or whatever.
We have some similar issues with _PAGE_CACHE_WP and _PAGE_NOCACHE,
both of which hide a "cachemode2protval()" call, and which also ends
up using another EXPORT_SYMBOL(), but at least that only triggers for
the much more rare cases.
Maybe we could move these dynamic page table bits to be generated much
deeper down in the VM layer, instead of hiding them in the macros that
everybody uses.
So this all would merit some cleanup. But not today. - Linus ]
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Despised-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 8 Nov 2017 19:21:52 +0000 (11:21 -0800)]
Merge branch 'fixes-v4.14-rc8' of git://git./linux/kernel/git/jmorris/linux-security
Pull key handling fix from James Morris:
"Fix by Eric Biggers for the keys subsystem"
* 'fixes-v4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: fix NULL pointer dereference during ASN.1 parsing [ver #2]
John Johansen [Wed, 8 Nov 2017 16:09:52 +0000 (08:09 -0800)]
apparmor: fix off-by-one comparison on MAXMAPPED_SIG
This came in yesterday, and I have verified our regression tests
were missing this and it can cause an oops. Please apply.
There is a an off-by-one comparision on sig against MAXMAPPED_SIG
that can lead to a read outside the sig_map array if sig
is MAXMAPPED_SIG. Fix this.
Verified that the check is an out of bounds case that can cause an oops.
Revised: add comparison fix to second case
Fixes:
cd1dbf76b23d ("apparmor: add the ability to mediate signals")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Biggers [Tue, 7 Nov 2017 22:29:02 +0000 (22:29 +0000)]
KEYS: fix NULL pointer dereference during ASN.1 parsing [ver #2]
syzkaller reported a NULL pointer dereference in asn1_ber_decoder(). It
can be reproduced by the following command, assuming
CONFIG_PKCS7_TEST_KEY=y:
keyctl add pkcs7_test desc '' @s
The bug is that if the data buffer is empty, an integer underflow occurs
in the following check:
if (unlikely(dp >= datalen - 1))
goto data_overrun_error;
This results in the NULL data pointer being dereferenced.
Fix it by checking for 'datalen - dp < 2' instead.
Also fix the similar check for 'dp >= datalen - n' later in the same
function. That one possibly could result in a buffer overread.
The NULL pointer dereference was reproducible using the "pkcs7_test" key
type but not the "asymmetric" key type because the "asymmetric" key type
checks for a 0-length payload before calling into the ASN.1 decoder but
the "pkcs7_test" key type does not.
The bug report was:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: asn1_ber_decoder+0x17f/0xe60 lib/asn1_decoder.c:233
PGD
7b708067 P4D
7b708067 PUD
7b6ee067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in:
CPU: 0 PID: 522 Comm: syz-executor1 Not tainted 4.14.0-rc8 #7
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.3-20171021_125229-anatol 04/01/2014
task:
ffff9b6b3798c040 task.stack:
ffff9b6b37970000
RIP: 0010:asn1_ber_decoder+0x17f/0xe60 lib/asn1_decoder.c:233
RSP: 0018:
ffff9b6b37973c78 EFLAGS:
00010216
RAX:
0000000000000000 RBX:
0000000000000000 RCX:
000000000000021c
RDX:
ffffffff814a04ed RSI:
ffffb1524066e000 RDI:
ffffffff910759e0
RBP:
ffff9b6b37973d60 R08:
0000000000000001 R09:
ffff9b6b3caa4180
R10:
0000000000000000 R11:
0000000000000000 R12:
0000000000000002
R13:
0000000000000000 R14:
0000000000000000 R15:
0000000000000000
FS:
00007f10ed1f2700(0000) GS:
ffff9b6b3ea00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000000000000 CR3:
000000007b6f3000 CR4:
00000000000006f0
Call Trace:
pkcs7_parse_message+0xee/0x240 crypto/asymmetric_keys/pkcs7_parser.c:139
verify_pkcs7_signature+0x33/0x180 certs/system_keyring.c:216
pkcs7_preparse+0x41/0x70 crypto/asymmetric_keys/pkcs7_key_type.c:63
key_create_or_update+0x180/0x530 security/keys/key.c:855
SYSC_add_key security/keys/keyctl.c:122 [inline]
SyS_add_key+0xbf/0x250 security/keys/keyctl.c:62
entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x4585c9
RSP: 002b:
00007f10ed1f1bd8 EFLAGS:
00000216 ORIG_RAX:
00000000000000f8
RAX:
ffffffffffffffda RBX:
00007f10ed1f2700 RCX:
00000000004585c9
RDX:
0000000020000000 RSI:
0000000020008ffb RDI:
0000000020008000
RBP:
0000000000000000 R08:
ffffffffffffffff R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000216 R12:
00007fff1b2260ae
R13:
00007fff1b2260af R14:
00007f10ed1f2700 R15:
0000000000000000
Code: dd ca ff 48 8b 45 88 48 83 e8 01 4c 39 f0 0f 86 a8 07 00 00 e8 53 dd ca ff 49 8d 46 01 48 89 85 58 ff ff ff 48 8b 85 60 ff ff ff <42> 0f b6 0c 30 89 c8 88 8d 75 ff ff ff 83 e0 1f 89 8d 28 ff ff
RIP: asn1_ber_decoder+0x17f/0xe60 lib/asn1_decoder.c:233 RSP:
ffff9b6b37973c78
CR2:
0000000000000000
Fixes:
42d5ec27f873 ("X.509: Add an ASN.1 decoder")
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: <stable@vger.kernel.org> # v3.7+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Yi Yang [Tue, 7 Nov 2017 13:07:02 +0000 (21:07 +0800)]
openvswitch: enable NSH support
v16->17
- Fixed disputed check code: keep them in nsh_push and nsh_pop
but also add them in __ovs_nla_copy_actions
v15->v16
- Add csum recalculation for nsh_push, nsh_pop and set_nsh
pointed out by Pravin
- Move nsh key into the union with ipv4 and ipv6 and add
check for nsh key in match_validate pointed out by Pravin
- Add nsh check in validate_set and __ovs_nla_copy_actions
v14->v15
- Check size in nsh_hdr_from_nlattr
- Fixed four small issues pointed out By Jiri and Eric
v13->v14
- Rename skb_push_nsh to nsh_push per Dave's comment
- Rename skb_pop_nsh to nsh_pop per Dave's comment
v12->v13
- Fix NSH header length check in set_nsh
v11->v12
- Fix missing changes old comments pointed out
- Fix new comments for v11
v10->v11
- Fix the left three disputable comments for v9
but not fixed in v10.
v9->v10
- Change struct ovs_key_nsh to
struct ovs_nsh_key_base base;
__be32 context[NSH_MD1_CONTEXT_SIZE];
- Fix new comments for v9
v8->v9
- Fix build error reported by daily intel build
because nsh module isn't selected by openvswitch
v7->v8
- Rework nested value and mask for OVS_KEY_ATTR_NSH
- Change pop_nsh to adapt to nsh kernel module
- Fix many issues per comments from Jiri Benc
v6->v7
- Remove NSH GSO patches in v6 because Jiri Benc
reworked it as another patch series and they have
been merged.
- Change it to adapt to nsh kernel module added by NSH
GSO patch series
v5->v6
- Fix the rest comments for v4.
- Add NSH GSO support for VxLAN-gpe + NSH and
Eth + NSH.
v4->v5
- Fix many comments by Jiri Benc and Eric Garver
for v4.
v3->v4
- Add new NSH match field ttl
- Update NSH header to the latest format
which will be final format and won't change
per its author's confirmation.
- Fix comments for v3.
v2->v3
- Change OVS_KEY_ATTR_NSH to nested key to handle
length-fixed attributes and length-variable
attriubte more flexibly.
- Remove struct ovs_action_push_nsh completely
- Add code to handle nested attribute for SET_MASKED
- Change PUSH_NSH to use the nested OVS_KEY_ATTR_NSH
to transfer NSH header data.
- Fix comments and coding style issues by Jiri and Eric
v1->v2
- Change encap_nsh and decap_nsh to push_nsh and pop_nsh
- Dynamically allocate struct ovs_action_push_nsh for
length-variable metadata.
OVS master and 2.8 branch has merged NSH userspace
patch series, this patch is to enable NSH support
in kernel data path in order that OVS can support
NSH in compat mode by porting this.
Signed-off-by: Yi Yang <yi.y.yang@intel.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Eric Garver <e@erig.me>
Acked-by: Pravin Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kristian Evensen [Tue, 7 Nov 2017 12:47:56 +0000 (13:47 +0100)]
qmi_wwan: Add missing skb_reset_mac_header-call
When we receive a packet on a QMI device in raw IP mode, we should call
skb_reset_mac_header() to ensure that skb->mac_header contains a valid
offset in the packet. While it shouldn't really matter, the packets have
no MAC header and the interface is configured as-such, it seems certain
parts of the network stack expects a "good" value in skb->mac_header.
Without the skb_reset_mac_header() call added in this patch, for example
shaping traffic (using tc) triggers the following oops on the first
received packet:
[ 303.642957] skbuff: skb_under_panic: text:
8f137918 len:177 put:67 head:
8e4b0f00 data:
8e4b0eff tail:0x8e4b0fb0 end:0x8e4b1520 dev:wwan0
[ 303.655045] Kernel bug detected[#1]:
[ 303.658622] CPU: 1 PID: 1002 Comm: logd Not tainted 4.9.58 #0
[ 303.664339] task:
8fdf05e0 task.stack:
8f15c000
[ 303.668844] $ 0 :
00000000 00000001 0000007a 00000000
[ 303.674062] $ 4 :
8149a2fc 8149a2fc 8149ce20 00000000
[ 303.679284] $ 8 :
00000030 3878303a 31623465 20303235
[ 303.684510] $12 :
ded731e3 2626a277 00000000 03bd0000
[ 303.689747] $16 :
8ef62b40 00000043 8f137918 804db5fc
[ 303.694978] $20 :
00000001 00000004 8fc13800 00000003
[ 303.700215] $24 :
00000001 8024ab10
[ 303.705442] $28 :
8f15c000 8fc19cf0 00000043 802cc920
[ 303.710664] Hi :
00000000
[ 303.713533] Lo :
74e58000
[ 303.716436] epc :
802cc920 skb_panic+0x58/0x5c
[ 303.721046] ra :
802cc920 skb_panic+0x58/0x5c
[ 303.725639] Status:
11007c03 KERNEL EXL IE
[ 303.729823] Cause :
50800024 (ExcCode 09)
[ 303.733817] PrId :
0001992f (MIPS 1004Kc)
[ 303.737892] Modules linked in: rt2800pci rt2800mmio rt2800lib qcserial ppp_async option usb_wwan rt2x00pci rt2x00mmio rt2x00lib rndis_host qmi_wwan ppp_generic nf_nat_pptp nf_conntrack_pptp nf_conntrack_ipv6 mt76x2i
Process logd (pid: 1002, threadinfo=
8f15c000, task=
8fdf05e0, tls=
77b3eee4)
[ 303.962509] Stack :
00000000 80408990 8f137918 000000b1 00000043 8e4b0f00 8e4b0eff 8e4b0fb0
[ 303.970871]
8e4b1520 8fec1800 00000043 802cd2a4 6e000045 00000043 00000000 8ef62000
[ 303.979219]
8eef5d00 8ef62b40 8fea7300 8f137918 00000000 00000000 0002bb01 793e5664
[ 303.987568]
8ef08884 00000001 8fea7300 00000002 8fc19e80 8eef5d00 00000006 00000003
[ 303.995934]
00000000 8030ba90 00000003 77ab3fd0 8149dc80 8004d1bc 8f15c000 8f383700
[ 304.004324] ...
[ 304.006767] Call Trace:
[ 304.009241] [<
802cc920>] skb_panic+0x58/0x5c
[ 304.013504] [<
802cd2a4>] skb_push+0x78/0x90
[ 304.017783] [<
8f137918>] 0x8f137918
[ 304.021269] Code:
00602825 0c02a3b4 24842888 <
000c000d>
8c870060 8c8200a0 0007382b 00070336 8c88005c
[ 304.031034]
[ 304.032805] ---[ end trace
b778c482b3f0bda9 ]---
[ 304.041384] Kernel panic - not syncing: Fatal exception in interrupt
[ 304.051975] Rebooting in 3 seconds..
While the oops is for a 4.9-kernel, I was able to trigger the same oops with
net-next as of yesterday.
Fixes:
32f7adf633b9 ("net: qmi_wwan: support "raw IP" mode")
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jay Vosburgh [Tue, 7 Nov 2017 10:50:07 +0000 (19:50 +0900)]
bonding: fix slave stuck in BOND_LINK_FAIL state
The bonding miimon logic has a flaw, in that a failure of the
rtnl_trylock can cause a slave to become permanently stuck in
BOND_LINK_FAIL state.
The sequence of events to cause this is as follows:
1) bond_miimon_inspect finds that a slave's link is down, and so
calls bond_propose_link_state, setting slave->new_link_state to
BOND_LINK_FAIL, then sets slave->new_link to BOND_LINK_DOWN and returns
non-zero.
2) In bond_mii_monitor, the rtnl_trylock fails, and the timer is
rescheduled. No change is committed.
3) bond_miimon_inspect is called again, but this time the slave
from step 1 has recovered. slave->new_link is reset to NOCHANGE, and, as
slave->link was never changed, the switch enters the BOND_LINK_UP case,
and does nothing. The pending BOND_LINK_FAIL state from step 1 remains
pending, as new_link_state is not reset.
4) The state from step 3 persists until another slave changes link
state and causes bond_miimon_inspect to return non-zero. At this point,
the BOND_LINK_FAIL state change on the slave from steps 1-3 is committed,
and the slave will remain stuck in BOND_LINK_FAIL state even though it
is actually link up.
The remedy for this is to initialize new_link_state on each entry
to bond_miimon_inspect, as is already done with new_link.
Fixes:
fb9eb899a6dc ("bonding: handle link transition from FAIL to UP correctly")
Reported-by: Alex Sidorenko <alexandre.sidorenko@hpe.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Tue, 7 Nov 2017 10:38:32 +0000 (11:38 +0100)]
pktgen: document 32-bit timestamp overflow
Timestamps in pktgen are currently retrieved using the deprecated
do_gettimeofday() function that wraps its signed 32-bit seconds in 2038
(on 32-bit architectures) and requires a division operation to calculate
microseconds.
The pktgen header is also defined with the same limitations, hardcoding
to a 32-bit seconds field that can be interpreted as unsigned to produce
times that only wrap in 2106. Whatever code reads the timestamps should
be aware of that problem in general, but probably doesn't care too
much as we are mostly interested in the time passing between packets,
and that is correctly represented.
Using 64-bit nanoseconds would be cheaper and good for 584 years. Using
monotonic times would also make this unambiguous by avoiding the overflow,
but would make it harder to correlate to the times with those on remote
machines. Either approach would require adding a new runtime flag and
implementing the same thing on the remote side, which we probably don't
want to do unless someone sees it as a real problem. Also, this should
be coordinated with other pktgen implementations and might need a new
magic number.
For the moment, I'm documenting the overflow in the source code, and
changing the implementation over to an open-coded ktime_get_real_ts64()
plus division, so we don't have to look at it again while scanning for
deprecated time interfaces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjorn Andersson [Tue, 7 Nov 2017 04:50:35 +0000 (20:50 -0800)]
qrtr: Move to postcore_initcall
Registering qrtr with module_init makes the ability of typical platform
code to create AF_QIPCRTR socket during probe a matter of link order
luck. Moving qrtr to postcore_initcall() avoids this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Nov 2017 05:22:50 +0000 (14:22 +0900)]
Merge git://git./linux/kernel/git/pablo/nf-next
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree, they are:
1) Speed up table replacement on busy systems with large tables
(and many cores) in x_tables. Now xt_replace_table() synchronizes by
itself by waiting until all cpus had an even seqcount and we use no
use seqlock when fetching old counters, from Florian Westphal.
2) Add nf_l4proto_log_invalid() and nf_ct_l4proto_log_invalid() to speed
up packet processing in the fast path when logging is not enabled, from
Florian Westphal.
3) Precompute masked address from configuration plane in xt_connlimit,
from Florian.
4) Don't use explicit size for set selection if performance set policy
is selected.
5) Allow to get elements from an existing set in nf_tables.
6) Fix incorrect check in nft_hash_deactivate(), from Florian.
7) Cache netlink attribute size result in l4proto->nla_size, from
Florian.
8) Handle NFPROTO_INET in nf_ct_netns_get() from conntrack core.
9) Use power efficient workqueue in conntrack garbage collector, from
Vincent Guittot.
10) Remove unnecessary parameter, in conntrack l4proto functions, also
from Florian.
11) Constify struct nf_conntrack_l3proto definitions, from Florian.
12) Remove all typedefs in nf_conntrack_h323 via coccinelle semantic
patch, from Harsha Sharma.
13) Don't store address in the rbtree nodes in xt_connlimit, they are
never used, from Florian.
14) Fix out of bound access in the conntrack h323 helper, patch from
Eric Sesterhenn.
15) Print symbols for the address returned with %pS in IPVS, from
Helge Deller.
16) Proc output should only display its own netns in IPVS, from
KUWAZAWA Takuya.
17) Small clean up in size_entry_mwt(), from Colin Ian King.
18) Use test_and_clear_bit from nf_nat_proto_clean() instead of separated
non-atomic test and then clear bit, from Florian Westphal.
19) Consolidate prefix length maps in ipset, from Aaron Conole.
20) Fix sparse warnings in ipset, from Jozsef Kadlecsik.
21) Simplify list_set_memsize(), from simran singhal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Miquel Raynal [Mon, 6 Nov 2017 21:56:53 +0000 (22:56 +0100)]
net: mvpp2: add ethtool GOP statistics
Add ethtool statistics support by reading the GOP statistics from the
hardware counters. Also implement a workqueue to gather the statistics
every second or some 32-bit counters could overflow.
Suggested-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Nov 2017 04:53:34 +0000 (13:53 +0900)]
Merge branch 'fsl-fman-next'
Christophe JAILLET says:
====================
fsl/fman: Fix some error handling code in mac_probe
Commit
c6e26ea8c893 ("dpaa_eth: change device used") generated some
conflicts in my patches waiting for submission. So I took a closer look at
it.
So here is a serie of 4 patches.
The 1st one is just about a spurious call to 'dev_set_drvdata()', which is
done in only 1 error handling path in the function.
The 2nd one removes some devm_iounmap/release/kfree functions which look
useless to me.
The 3rd one fixes a missing of_node_put.
The 4th one is just cosmetic and removes a useless message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Mon, 6 Nov 2017 21:53:32 +0000 (22:53 +0100)]
fsl/fman: Remove a useless 'dev_err()' call
Memory allocation functions already display some informaton in case of
memory allocation failure. There is no need to add an extra 'dev_err' here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Mon, 6 Nov 2017 21:53:31 +0000 (22:53 +0100)]
fsl/fman: Add a missing 'of_node_put()' call in an error handling path
If 'of_phy_find_device()' fails, we must undo the previous 'of_node_get()'
call, as done the the following error handling code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Mon, 6 Nov 2017 21:53:30 +0000 (22:53 +0100)]
fsl/fman: Remove some useless code
There is no need to release explicitly some devm_ allocated resources.
If the 'mac_probe()' probe function fails, they will be released
automatically, as already done in the other error handling paths of
this function.
Also goto '_return_of_get_parent' as in the other error handling paths.
This is useless (priv->fixed_link is NULL at this point), but at least
it is consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Mon, 6 Nov 2017 21:53:29 +0000 (22:53 +0100)]
fsl/fman: Remove a useless call to 'dev_set_drvdata()'
Commit
c6e26ea8c893 ("dpaa_eth: change device used") has removed usage of
'dev_set_drvdata()' in the 'mac_probe() function.
This call should also be axed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Mon, 6 Nov 2017 15:04:54 +0000 (15:04 +0000)]
rtnetlink: fix missing size for IFLA_IF_NETNSID
The size for IFLA_IF_NETNSID is missing from the size calculation
because the proceeding semicolon was not removed. Fix this by removing
the semicolon.
Detected by CoverityScan, CID#
1461135 ("Structurally dead code")
Fixes:
79e1ad148c84 ("rtnetlink: use netnsid to query interface")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Mon, 6 Nov 2017 14:32:18 +0000 (15:32 +0100)]
net: qmi_wwan: fix divide by 0 on bad descriptors
A CDC Ethernet functional descriptor with wMaxSegmentSize = 0 will
cause a divide error in usbnet_probe:
divide error: 0000 [#1] PREEMPT SMP KASAN
Modules linked in:
CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted
4.14.0-rc8-44453-g1fdc1a82c34f #56
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
task:
ffff88006bef5c00 task.stack:
ffff88006bf60000
RIP: 0010:usbnet_update_max_qlen+0x24d/0x390 drivers/net/usb/usbnet.c:355
RSP: 0018:
ffff88006bf67508 EFLAGS:
00010246
RAX:
00000000000163c8 RBX:
ffff8800621fce40 RCX:
ffff8800621fcf34
RDX:
0000000000000000 RSI:
ffffffff837ecb7a RDI:
ffff8800621fcf34
RBP:
ffff88006bf67520 R08:
ffff88006bef5c00 R09:
ffffed000c43f881
R10:
ffffed000c43f880 R11:
ffff8800621fc406 R12:
0000000000000003
R13:
ffffffff85c71de0 R14:
0000000000000000 R15:
0000000000000000
FS:
0000000000000000(0000) GS:
ffff88006ca00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007ffe9c0d6dac CR3:
00000000614f4000 CR4:
00000000000006f0
Call Trace:
usbnet_probe+0x18b5/0x2790 drivers/net/usb/usbnet.c:1783
qmi_wwan_probe+0x133/0x220 drivers/net/usb/qmi_wwan.c:1338
usb_probe_interface+0x324/0x940 drivers/usb/core/driver.c:361
really_probe drivers/base/dd.c:413
driver_probe_device+0x522/0x740 drivers/base/dd.c:557
Fix by simply ignoring the bogus descriptor, as it is optional
for QMI devices anyway.
Fixes:
423ce8caab7e ("net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Mon, 6 Nov 2017 14:37:22 +0000 (15:37 +0100)]
net: cdc_ether: fix divide by 0 on bad descriptors
Setting dev->hard_mtu to 0 will cause a divide error in
usbnet_probe. Protect against devices with bogus CDC Ethernet
functional descriptors by ignoring a zero wMaxSegmentSize.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Egil Hjelmeland [Mon, 6 Nov 2017 14:19:49 +0000 (15:19 +0100)]
net: dsa: lan9303: Drop port range check
Now that ds->num_ports is 3, there is no need to check range of "port"
parameter.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 6 Nov 2017 14:04:39 +0000 (15:04 +0100)]
bnxt: fix bnxt_hwrm_fw_set_time for y2038
On 32-bit architectures, rtc_time_to_tm() returns incorrect results
in 2038 or later, and do_gettimeofday() is broken for the same reason.
This changes the code to use ktime_get_real_seconds() and time64_to_tm()
instead, both of them are 2038-safe, and we can also get rid of the
CONFIG_RTC_LIB dependency that way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 6 Nov 2017 13:26:10 +0000 (14:26 +0100)]
of: add of_property_read_variable_* dummy helpers
Commit
a67e9472da42 ("of: Add array read functions with min/max size
limits") added a new interface for reading variable-length arrays from
DT properties. One user was added in dsa recently and this causes a
build error because that code can be built with CONFIG_OF disabled:
net/dsa/dsa2.c: In function 'dsa_switch_parse_member_of':
net/dsa/dsa2.c:678:7: error: implicit declaration of function 'of_property_read_variable_u32_array'; did you mean 'of_property_read_u32_array'? [-Werror=implicit-function-declaration]
This adds a dummy functions for of_property_read_variable_u32_array()
and a few others that had been missing here. I decided to move
of_property_read_string() and of_property_read_string_helper() in the
process to make it easier to compare the two sets of function prototypes
to make sure they match.
Fixes:
975e6e32215e ("net: dsa: rework switch parsing")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Mon, 6 Nov 2017 11:43:01 +0000 (14:43 +0300)]
bnxt: delete some unreachable code
We return on the previous line so this "return 0;" statement should just
be deleted.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Nov 2017 04:29:06 +0000 (13:29 +0900)]
Merge branch 'dsa-lan9303-Linting'
Egil Hjelmeland says:
====================
net: dsa: lan9303: Linting
This series is non-functional.
- Correct some errors in comments and documentation.
Remove scripts/checkpatch.pl WARNINGs and most CHECKs:
- Replace msleep(1) with usleep_range()
- Adjust indenting
Changes v1 -> v2:
- Removed patch 4 "Remove unnecessary parentheses", to be addressed later
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Egil Hjelmeland [Mon, 6 Nov 2017 11:42:04 +0000 (12:42 +0100)]
net: dsa: lan9303: Adjust indenting
Remove scripts/checkpatch.pl CHECKs by adjusting indenting.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Egil Hjelmeland [Mon, 6 Nov 2017 11:42:03 +0000 (12:42 +0100)]
net: dsa: lan9303: Replace msleep(1) with usleep_range()
Remove scripts/checkpatch.pl WARNING by replacing msleep(1) with usleep_range()
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Egil Hjelmeland [Mon, 6 Nov 2017 11:42:02 +0000 (12:42 +0100)]
net: dsa: lan9303: Fix syntax errors in device tree examples
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Egil Hjelmeland [Mon, 6 Nov 2017 11:42:01 +0000 (12:42 +0100)]
net: dsa: lan9303: Correct register names in comments
Two comments refer to registers, but lack the LAN9303_ prefix.
Fix that.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 6 Nov 2017 11:11:28 +0000 (11:11 +0000)]
mlxsw: spectrum: Fix error return code in mlxsw_sp_port_create()
Fix to return a negative error code from the VID create error handling
case instead of 0, as done elsewhere in this function.
Fixes:
c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 6 Nov 2017 11:12:08 +0000 (11:12 +0000)]
dpaa_eth: fix error return code in dpaa_eth_probe()
Fix to return a negative error code from the dpaa_bp_alloc() error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Nov 2017 03:23:39 +0000 (12:23 +0900)]
Merge branch 'qdisc-RED-offload'
Jiri Pirko says:
====================
qdisc RED offload
Nogah says:
Add an offload support for RED qdisc for mlxsw driver.
The first patch adds the ability to offload RED qdisc by using
ndo_setup_tc. It gives RED three commands, to offload, change or delete
the qdisc, to get the qdisc generic stats and to get it's RED xstats.
There is no enforcement on a driver to offload or not offload the qdisc and
it is up to the driver to decide.
RED qdisc is first being created and only later graft to a parent (unless
it is a root qdisc). For that reason the return value of the offload
replace command that is called in the init process doesn't reflect actual
offload state. The offload state is determined in the dump function so it
can be reflected to the user. This function is also responsible for stats
update.
The patchses 2-3 change the name of TC_SETUP_MQPRIO & TC_SETUP_CBS to match
with the new convention of QDISC prefix.
The rest of the patchset is driver support for the qdisc. Currently only
as root qdisc that is being set on the default traffic class. It supports
only the following parameters of RED: min, max, probability and ECN mode.
Limit and burst size related params are being ignored at this moment.
---
v7->v8 internal: (external RFC->v1)
- patch 1/9:
- unite the offload and un-offload functions
- clean the OFFLOAD flag when the qdisc in not offloaded
- patch 2/9:
- minor change to avoid a conflict
- patch 5/9:
- check for bad min/max values
- clean the offloaded qdisc after a bad config call
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Mon, 6 Nov 2017 06:23:49 +0000 (07:23 +0100)]
mlxsw: spectrum: Support general qdisc stats
Add support for ndo_setup_tc with enum tc_setup_type value of
TC_SETUP_QDISC_STATS. This call updates the generic qdisc stats from the
cache if the handle ID that is asked for matching the root qdisc ID and
fails otherwise.
Currently doesn't support qlen and rqueues.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Mon, 6 Nov 2017 06:23:48 +0000 (07:23 +0100)]
mlxsw: spectrum: Support RED xstats
Add support for ndo_setup_tc with enum tc_setup_type value of
TC_SETUP_RED_XSTATS. This call returns the RED qdisc xstats from the cache
if the handle ID that is asked for matching the root qdisc ID and fails
otherwise.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Mon, 6 Nov 2017 06:23:47 +0000 (07:23 +0100)]
mlxsw: spectrum: Collect tclass related stats periodically
Add more statistics to be collected from the HW periodically. These stats
are tclass based (beside ECN marked packet, that exist only port based).
They are needed to expose RED qdisc stats and xstats correctly.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 6 Nov 2017 06:23:46 +0000 (07:23 +0100)]
mlxsw: reg: Add ext and tc-cong counter groups
This adds the counter group definitions for 2 new counter groups
which are necessary for gaining ECN & wred counters.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Mon, 6 Nov 2017 06:23:45 +0000 (07:23 +0100)]
mlxsw: spectrum: Support RED qdisc offload
Add support for ndo_setup_tc with enum tc_setup_type value of TC_SETUP_RED.
This call sets RED qdisc on a traffic class.
This patch supports RED qdisc only as a root qdisc and set in on the
default tclass. It can be set with or without ECN.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Mon, 6 Nov 2017 06:23:44 +0000 (07:23 +0100)]
mlxsw: reg: Add cwtp & cwtpm registers
This patch adds 2 new registers:
- Congestion WRED ECN TClass Profile Register [CWTP]
- Congestion WRED ECN TClass and Pool Mapping Register [CWTPM]
These registers would later be needed to offload RED-related
functionality to the HW.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Mon, 6 Nov 2017 06:23:43 +0000 (07:23 +0100)]
net_sch: cbs: Change TC_SETUP_CBS to TC_SETUP_QDISC_CBS
Change TC_SETUP_CBS to TC_SETUP_QDISC_CBS to match the new convention..
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Mon, 6 Nov 2017 06:23:42 +0000 (07:23 +0100)]
net_sch: mqprio: Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO
Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new
convention.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Mon, 6 Nov 2017 06:23:41 +0000 (07:23 +0100)]
net_sch: red: Add offload ability to RED qdisc
Add the ability to offload RED qdisc by using ndo_setup_tc.
There are four commands for RED offloading:
* TC_RED_SET: handles set and change.
* TC_RED_DESTROY: handle qdisc destroy.
* TC_RED_STATS: update the qdiscs counters (given as reference)
* TC_RED_XSTAT: returns red xstats.
Whether RED is being offloaded is being determined every time dump action
is being called because parent change of this qdisc could change its
offload state but doesn't require any RED function to be called.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lawrence Brakmo [Mon, 6 Nov 2017 02:44:10 +0000 (18:44 -0800)]
bpf: Rename tcp_bbf.readme to tcp_bpf.readme
The original patch had the wrong filename.
Fixes:
bfdf75693875 ("bpf: create samples/bpf/tcp_bpf.readme")
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Mon, 6 Nov 2017 01:01:57 +0000 (09:01 +0800)]
bonding: discard lowest hash bit for 802.3ad layer3+4
After commit
07f4c90062f8 ("tcp/dccp: try to not exhaust ip_local_port_range
in connect()"), we will try to use even ports for connect(). Then if an
application (seen clearly with iperf) opens multiple streams to the same
destination IP and port, each stream will be given an even source port.
So the bonding driver's simple xmit_hash_policy based on layer3+4 addressing
will always hash all these streams to the same interface. And the total
throughput will limited to a single slave.
Change the tcp code will impact the whole tcp behavior, only for bonding
usage. Paolo Abeni suggested fix this by changing the bonding code only,
which should be more reasonable, and less impact.
Fix this by discarding the lowest hash bit because it contains little entropy.
After the fix we can re-balance between slaves.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Nov 2017 02:21:28 +0000 (11:21 +0900)]
Merge branch 'ila-make-identifier-format-optional-and-other-fixes'
Tom Herbert says:
====================
ila: make identifier format optional and other fixes
The identifier type and checksum neutral mapping bits are optional
in identifier formats. This patch set fixes the implementation to
make them optional and configurable.
Specific items:
- Clean up checksum diff code in ILA
- Add checksum neutral mapping auto so that checksum neutral
mapping can be configured without requiring use of the C-bit
- Add identifier type configuration and allow identifier
type to be configured so that the identifier type field does
not need to be present
- Added ILA documention: ila.txt
I have fixes for ILA in iproute2 that will be poseted separately.
Tested: Ran netperf TCP_RR on various combinations of checksum
mode and the two supported identifier types.
v2:
- Add proper sign off
- In ILA LWT, only check prefix length includes identifier type
if identifier type is enabled (ILA_ATYPE_USE_FORMAT).
- Add a hook type so that it can be specified whether ILA
translation is done on input or output route funciton in
LWT.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 5 Nov 2017 23:58:26 +0000 (15:58 -0800)]
ila: Add ila.txt
Add documenation for kernel ILA. This describes ILA, features,
configuration gives some examples.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 5 Nov 2017 23:58:25 +0000 (15:58 -0800)]
ila: Add a hook type for LWT routes
In LWT tunnels both an input and output route method is defined.
If both of these are executed in the same path then double translation
happens and the effect is not correct.
This patch adds a new attribute that indicates the hook type. Two
values are defined for route output and route output. ILA
translation is only done for the one that is set. The default is
to enable ILA on route output.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 5 Nov 2017 23:58:24 +0000 (15:58 -0800)]
ila: allow configuration of identifier type
Allow identifier to be explicitly configured for a mapping.
This can either be one of the identifier types specified in the
ILA draft or a value of ILA_ATYPE_USE_FORMAT which means the
identifier type is inferred from the identifier type field.
If a value other than ILA_ATYPE_USE_FORMAT is set for a
mapping then it is assumed that the identifier type field is
not present in an identifier.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 5 Nov 2017 23:58:23 +0000 (15:58 -0800)]
ila: add checksum neutral map auto
Add checksum neutral auto that performs checksum neutral mapping
without using the C-bit. This is enabled by configuration of
a mapping.
The checksum neutral function has been split into
ila_csum_do_neutral_fmt and ila_csum_do_neutral_nofmt. The former
handles the C-bit and includes it in the adjustment value. The latter
just sets the adjustment value on the locator diff only.
Added configuration for checksum neutral map aut in ila_lwt
and ila_xlat.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 5 Nov 2017 23:58:22 +0000 (15:58 -0800)]
ila: cleanup checksum diff
Consolidate computing checksum diff into one function.
Add get_csum_diff_iaddr that computes the checksum diff between
an address argument and locator being written. get_csum_diff
calls this using the destination address in the IP header as
the argument.
Also moved ila_init_saved_csum to be close to the checksum
diff functions.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Sun, 5 Nov 2017 03:54:53 +0000 (22:54 -0500)]
net/mlx5e/core/en_fs: fix pointer dereference after free in mlx5e_execute_l2_action
hn is being kfree'd in mlx5e_del_l2_from_hash and then dereferenced
by accessing hn->ai.addr
Fix this by copying the MAC address into a local variable for its safe use
in all possible execution paths within function mlx5e_execute_l2_action.
Addresses-Coverity-ID:
1417789
Fixes:
eeb66cdb6826 ("net/mlx5: Separate between E-Switch and MPFS")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christina Jacob [Sun, 5 Nov 2017 03:22:30 +0000 (08:52 +0530)]
xdp: Sample xdp program implementing ip forward
Implements port to port forwarding with route table and arp table
lookup for ipv4 packets using bpf_redirect helper function and
lpm_trie map.
Signed-off-by: Christina Jacob <Christina.Jacob@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Troy Kisky [Fri, 3 Nov 2017 17:29:59 +0000 (10:29 -0700)]
net: fec: Let fec_ptp have its own interrupt routine
This is better for code locality and should slightly
speed up normal interrupts.
This also allows PPS clock output to start working for
i.mx7. This is because i.mx7 was already using the limit
of 3 interrupts, and needed another.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Zyngier [Sat, 4 Nov 2017 12:33:47 +0000 (12:33 +0000)]
net: mvpp2: Prevent userspace from changing TX affinities
The mvpp2 driver can't cope at all with the TX affinities being
changed from userspace, and spit an endless stream of
[ 91.779920] mvpp2
f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.779930] mvpp2
f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780402] mvpp2
f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780406] mvpp2
f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780415] mvpp2
f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780418] mvpp2
f4000000.ethernet eth2: wrong cpu on the end of Tx processing
rendering the box completely useless (I've measured around 600k
interrupts/s on a 8040 box) once irqbalance kicks in and start
doing its job.
Obviously, the driver was never designed with this in mind. So let's
work around the problem by preventing userspace from interacting
with these interrupts altogether.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Nov 2017 01:28:54 +0000 (10:28 +0900)]
Merge branch 'hv_netvsc-fix-a-hang-on-channel-mtu-changes'
Vitaly Kuznetsov says:
====================
hv_netvsc: fix a hang on channel/mtu changes
It was found that netvsc driver doesn't survive e.g.
test. I was able to identify a hang in guest/host communication, it is
fixed by PATCH1 of this series. PATCH2 is a cosmetic change masking
unneeded messages.
Changes since v1:
- Throw away patches 2 and 3 of the original series as one is unneeded and
the other is not justified [Eric Dumazet, Stephen Hemminger] so I'm only
fixing the hang now, the crash doesn't reproduce. Will keep an eye on it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Thu, 2 Nov 2017 10:35:31 +0000 (11:35 +0100)]
hv_netvsc: hide warnings about uninitialized/missing rndis device
Hyper-V hosts are known to send RNDIS messages even after we halt the
device in rndis_filter_halt_device(). Remove user visible messages
as they are not really useful.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Thu, 2 Nov 2017 10:35:30 +0000 (11:35 +0100)]
hv_netvsc: netvsc_teardown_gpadl() split
It was found that in some cases host refuses to teardown GPADL for send/
receive buffers (probably when some work with these buffere is scheduled or
ongoing). Change the teardown logic to be:
1) Send NVSP_MSG1_TYPE_REVOKE_* messages
2) Close the channel
3) Teardown GPADLs.
This seems to work reliably.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej S. Szmigiero [Wed, 1 Nov 2017 23:49:18 +0000 (00:49 +0100)]
net: phy: leds: Add support for "link" trigger
Currently, we create a LED trigger for any link speed known to a PHY.
These triggers only fire when their exact link speed had been negotiated
(they aren't cumulative, that is, they don't fire for "their or any higher"
link speed).
What we are missing, however, is a trigger which will fire on any link
speed known to the PHY. Such trigger can then be used for implementing a
poor man's substitute of the "link" LED on boards that lack it.
Let's add it.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej S. Szmigiero [Wed, 1 Nov 2017 23:48:45 +0000 (00:48 +0100)]
net: phy: leds: Refactor "no link" handler into a separate function
Currently, phy_led_trigger_change_speed() is handling a "no link" condition
like it was some kind of an error (using "goto" to a code at the function
end).
However, having no link at PHY is an ordinary operational state, so let's
handle it in an appropriately named separate function so it is more obvious
what the code is doing.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Borislav Petkov [Tue, 7 Nov 2017 16:37:24 +0000 (17:37 +0100)]
drivers/ide-cd: Handle missing driver data during status check gracefully
The 0day bot reports the below failure which happens occasionally, with
their randconfig testing (once every ~100 boots). The Code points at
the private pointer ->driver_data being NULL, which hints at a race of
sorts where the private driver_data descriptor has disappeared by the
time we get to run the workqueue.
So let's check that pointer before we continue with issuing the command
to the drive.
This fix is of the brown paper bag nature but considering that IDE is
long deprecated, let's do that so that random testing which happens to
enable CONFIG_IDE during randconfig builds, doesn't fail because of
this.
Besides, failing the TEST_UNIT_READY command because the drive private
data is gone is something which we could simply do anyway, to denote
that there was a problem communicating with the device.
BUG: unable to handle kernel NULL pointer dereference at
000001c0
IP: cdrom_check_status
*pde =
00000000
Oops: 0000 [#1] SMP
CPU: 1 PID: 155 Comm: kworker/1:2 Not tainted 4.14.0-rc8 #127
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Workqueue: events_freezable_power_ disk_events_workfn
task:
4fe90980 task.stack:
507ac000
EIP: cdrom_check_status+0x2c/0x90
EFLAGS:
00210246 CPU: 1
EAX:
00000000 EBX:
4fefec00 ECX:
00000000 EDX:
00000000
ESI:
00000003 EDI:
ffffffff EBP:
467a9340 ESP:
507aded0
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
CR0:
80050033 CR2:
000001c0 CR3:
06e0f000 CR4:
00000690
Call Trace:
? ide_cdrom_check_events_real
? cdrom_check_events
? disk_check_events
? process_one_work
? process_one_work
? worker_thread
? kthread
? process_one_work
? __kthread_create_on_node
? ret_from_fork
Code: 53 83 ec 14 89 c3 89 d1 be 03 00 00 00 65 a1 14 00 00 00 89 44 24 10 31 c0 8b 43 18 c7 44 24 04 00 00 00 00 c7 04 24 00 00 00 00 <8a> 80 c0 01 00 00 c7 44 24 08 00 00 00 00 83 e0 03 c7 44 24 0c
EIP: cdrom_check_status+0x2c/0x90 SS:ESP: 0068:
507aded0
CR2:
00000000000001c0
---[ end trace
2410e586dd8f88b2 ]---
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 7 Nov 2017 17:04:32 +0000 (09:04 -0800)]
Revert "scsi: make 'state' device attribute pollable"
This reverts commit
8a97712e5314aefe16b3ffb4583a34deaa49de04.
This commit added a call to sysfs_notify() from within
scsi_device_set_state(), which in turn turns out to make libata very
unhappy, because ata_eh_detach_dev() does
spin_lock_irqsave(ap->lock, flags);
..
if (ata_scsi_offline_dev(dev)) {
dev->flags |= ATA_DFLAG_DETACHED;
ap->pflags |= ATA_PFLAG_SCSI_HOTPLUG;
}
and ata_scsi_offline_dev() then does that scsi_device_set_state() to set
it offline.
So now we called sysfs_notify() from within a spinlocked region, which
really doesn't work. The 0day robot reported this as:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:238
because sysfs_notify() ends up calling kernfs_find_and_get_ns() which
then does mutex_lock(&kernfs_mutex)..
The pollability of the device state isn't critical, so revert this all
for now, and maybe we'll do it differently in the future.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takashi Iwai [Tue, 7 Nov 2017 15:05:24 +0000 (16:05 +0100)]
ALSA: seq: Fix OSS sysex delivery in OSS emulation
The SYSEX event delivery in OSS sequencer emulation assumed that the
event is encoded in the variable-length data with the straight
buffering. This was the normal behavior in the past, but during the
development, the chained buffers were introduced for carrying more
data, while the OSS code was left intact. As a result, when a SYSEX
event with the chained buffer data is passed to OSS sequencer port,
it may end up with the wrong memory access, as if it were having a too
large buffer.
This patch addresses the bug, by applying the buffer data expansion by
the generic snd_seq_dump_var_event() helper function.
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: Mark Salyzyn <salyzyn@android.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>