OSDN Git Service
Florian Fainelli [Fri, 30 Aug 2013 14:36:14 +0000 (15:36 +0100)]
net: fix comment typo for __skb_alloc_pages()
The name of the function in the comment is __skb_alloc_page() while we
are actually commenting __skb_alloc_pages(). Fix this typo and make it
a valid kernel doc comment.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Fri, 30 Aug 2013 12:01:15 +0000 (15:01 +0300)]
gianfar: Fix reported number of sent bytes to BQL
Fix the amount of sent bytes reported to BQL by reporting the
number of bytes on wire in the xmit routine, and recording that
value for each skb in order to be correctly confirmed on Tx
confirmation cleanup.
Reporting skb->len to BQL just before exiting xmit is not correct
due to possible insertions of TOE block and alignment bytes in the
skb->data, which are being stripped off by the controller before
transmission on wire. This led to mismatch of (incorrectly)
reported bytes to BQL b/w xmit and Tx confirmation, resulting in
Tx timeout firing, for the h/w tx timestamping acceleration case.
There's no easy way to obtain the number of bytes on wire in the Tx
confirmation routine, so skb->cb is used to convey that information
from xmit to Tx confirmation, for now (as proposed by Eric). Revived
the currently unused GFAR_CB() construct for that purpose.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Aloni [Fri, 30 Aug 2013 10:59:46 +0000 (13:59 +0300)]
netconsole: avoid a crash with multiple sysfs writers
When my 'ifup eth' script was fired multiple times and ran concurrent on
my laptop, for some obscure /etc scripting reason, it was revealed
that the store_enabled() function in netconsole doesn't handle it nicely,
as recorded by the Oops below (a syslog paste, but not mangled too much
to prevent from discerning the traceback).
On Linux 3.10.4, this patch seeks to remedy the problem, and it has been
running stable on my laptop for a few days.
[52608.609325] BUG: unable to handle kernel NULL pointer dereference at
00000000000003e0
[52608.609331] IP: [<
ffffffff81532a17>] __netpoll_cleanup+0x27/0xe0
[52608.609339] PGD
15e51a067 PUD
15433e067 PMD 0
[52608.609343] Oops: 0000 [#1] SMP re firewire_ohci firewire_core crc_itu_t [last unloaded: kvm_intel]
[52608.609347] Modules linked in: kvm_intel tun vfat fat ppdev parport_pc parport fuse ipt_MASQUERADE usb_storage nf_conntrack_netbios_ns nf_conn [..garbled..]
[52608.609433] RAX:
0000000000000000 RBX:
ffff880210bbcc68 RCX:
0000000000000000
[52608.609435] RDX:
0000000000000000 RSI:
ffff8801ba447da0 RDI:
ffff880210bbcc68
[52608.609437] RBP:
ffff8801ba447e18 R08:
0000000000000000 R09:
0000000000000001
[52608.609439] R10:
000000000000000a R11:
f000000000000000 R12:
ffff880210bbcc68
[52608.609441] R13:
ffff88020bc41000 R14:
0000000000000002 R15:
000000000000000200000000000
[52608.609443] FS:
00007f38d7bff740(0000) GS:
ffff88021dc40000(0000) knlGS:
0000000000000000
[52608.609446] CS: 0010 DS: 0000 ES: 0000 CR0:
000000008005003300000000001427e0
[52608.609448] CR2:
00000000000003e0 CR3:
0000000154103000 CR4:
00000000001427e0
[52608.609450] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[52608.609452] netpoll: netconsole: local port 6665ess 10.0.0.27
[52608.609454] netpoll: netconsole: local IPv4 address 10.0.0.27
[52608.609456] netpoll: netconsole: interface 'em1'
[52608.609457] netpoll: netconsole: remote port 514ress 10.0.0.15
[52608.609459] netpoll: netconsole: remote IPv4 address 10.0.0.15:65:a8:9a:c7
[52608.609461] netpoll: netconsole: remote ethernet address 1c:6f:65:a8:9a:c7
[52608.609463] DR3:
0000000000000000 DR6:
00000000ffff0ff0 DR7:
0000000000000400
[52608.609464] Stack:
801ba447e08 ffff880210bbcc68 ffffffffffffffea ffff88020bc41000
[52608.609466]
ffff8801ba447e08 ffff880210bbcc68 ffffffffffffffea ffff88020bc41000
[52608.609471]
0000000000000002 0000000000000002 ffff8801ba447e38 ffffffff81532af4
[52608.609475]
0000000000000000 ffff880210bbcc00 ffff8801ba447e78 ffffffff81420e7c
[52608.609479] Call Trace:
[52608.609484] [<
ffffffff81532af4>] netpoll_cleanup+0x24/0x50
[52608.609489] [<
ffffffff81420e7c>] store_enabled+0x5c/0xe0
[52608.609492] [<
ffffffff81420abe>] netconsole_target_attr_store+0x2e/0x40
[52608.609498] [<
ffffffff811ff2a2>] configfs_write_file+0xd2/0x130
[52608.609503] [<
ffffffff81188f95>] vfs_write+0xc5/0x1f0
[52608.609506] [<
ffffffff81189482>] SyS_write+0x52/0xa0/0x10
[52608.609511] [<
ffffffff81628c2e>] ? do_page_fault+0xe/0x10
[52608.609516] [<
ffffffff8162d402>] system_call_fastpath+0x16/0x1b
[52608.609517] Code: 1f 44 00 00 0f 1f 44 00 00 55 48 89 e5 48 83 ec 30 4c 89 65 e0 48 89 5d d8 49 89 fc 4c 89 6d e8 4c 89 75 f0 4c 89 7d f8 48 8 [..garbled..]
[52608.609559] RIP [<
ffffffff81532a17>] __netpoll_cleanup+0x27/0xe0
[52608.609563] RSP <
ffff8801ba447de8>
[52608.609564] CR2:
00000000000003e0
[52608.609567] ---[ end trace
d25ec343349b61d2 ]---
Signed-off-by: Dan Aloni <alonid@postram.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kouei Abe [Fri, 30 Aug 2013 03:41:08 +0000 (12:41 +0900)]
sh_eth: Enable Rx descriptor word 0 shift for r8a7790
This corrects an oversight when r8a7790 support was added to sh_eth.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kouei Abe [Fri, 30 Aug 2013 03:41:07 +0000 (12:41 +0900)]
sh_eth: Fix cache invalidation omission of receive buffer
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Veaceslav Falico [Thu, 29 Aug 2013 21:38:57 +0000 (23:38 +0200)]
bonding: use rlb_client_info->vlan_id instead of ->tag
Store VID in ->vlan_id (if any), and remove the useless ->tag.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Veaceslav Falico [Thu, 29 Aug 2013 21:38:56 +0000 (23:38 +0200)]
bonding: remove bond_vlan_used()
We're using it currently to verify if we have vlans before getting the tag
from the skb we're about to send. It's useless because the vlan_get_tag()
verifies if the skb has the tag (and returns an error if not), and we can
receive tagged skbs only if we *already* have vlans.
Plus, the current RCUed implementation is kind of useless anyway - the we
can remove the last vlan in the moment we return from the function.
So remove the only usage of it and the whole function.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 4 Sep 2013 01:54:02 +0000 (21:54 -0400)]
Merge branch 'for-davem' of git://gitorious.org/linux-can/linux-can-next
Marc Kleine-Budde says:
====================
this is a pull request for net-next. There are two patches from Gerhard
Sittig, which improves the clock handling on mpc5121. Oliver Hartkopp
provides a patch that adds a per rule limitation of frame hops.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 4 Sep 2013 01:45:31 +0000 (21:45 -0400)]
Merge branch 'for-davem' of git://git./linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
Please accept this batch of updates intended for the 3.12 stream.
For the mac80211 bits, Johannes says this:
"This time I have various improvements all over the place: IBSS, mesh,
testmode, AP client powersave handling, one of the rare rfkill patches
and some code cleanup."
Also for mac80211:
"And I also have some more changes for -next, just a few small fixes and
improvements, nothing really stands out."
And for iwlwifi:
"This time I have some powersave work (notably uAPSD support), CQM
offloads, support for a new firmware API and various code cleanups."
Regarding the Bluetooth bits, Gustavo says:
"Patches to 3.12, here we have:
* implementation of a proper tty_port for RFCOMM devices, this fixes some
issues people were seeing lately in the kernel.
* Add voice_setting option for SCO, it is used for SCO Codec selection
* bugfixes, small improvements and clean ups"
For the NFC bits, Samuel says:
"With this one we have:
- A few pn533 improvements and minor fixes. Testing our pn533 driver
against Google's NCI stack triggered a few issues that we fixed now.
We also added Tx fragmentation support to this driver.
- More NFC secure element handling. We added a GET_SE netlink command
for getting all the discovered secure elements, and we defined 2
additional secure element netlink event (transaction and connectivity).
We also fixed a couple of typos and copy-paste bugs from the secure
element handling code.
- Firmware download support for the pn544 driver. This chipset can enter a
special mode where it's waiting for firmware blobs to replace the
already flashed one. We now support that mode."
With repect to the ath tree, Kalle says:
"New features in ath10k are rx/tx checsumming in hw and survey scan
implemented by Michal. Also he made fixes to different areas of the
driver, most notable being fixing the case when using two streams and
reducing the number of interface combinations to avoid firmware crashes.
Bartosz did a clean related to how we handle SoC power save in PCI
layer.
For ath6kl Mohammed and Vasanth sent each a patch to fix two infrequent
crashes."
I also pulled the wireless tree into wireless-next to support a
request from Johannes. On top of all that, there are the usual
sort of driver updates. The mwifiex, brcmfmac, brcmsmac, ath9k,
and rt2x00 drivers all get some attention, as does the bcma bus and
a few other random bits here and there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 29 Aug 2013 16:54:49 +0000 (18:54 +0200)]
net: sctp: probe: allow more advanced ingress filtering by mark
This is a follow-up commit for commit
b1dcdc68b1f4 ("net: tcp_probe:
allow more advanced ingress filtering by mark") that allows for
advanced SCTP probe module filtering based on skb mark (for a more
detailed description and advantages using mark, refer to
b1dcdc68b1f4).
The current option to filter by a given port is still being preserved.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tim Gardner [Thu, 29 Aug 2013 12:38:47 +0000 (06:38 -0600)]
net: neighbour: Remove CONFIG_ARPD
This config option is superfluous in that it only guards a call
to neigh_app_ns(). Enabling CONFIG_ARPD by default has no
change in behavior. There will now be call to __neigh_notify()
for each ARP resolution, which has no impact unless there is a
user space daemon waiting to receive the notification, i.e.,
the case for which CONFIG_ARPD was designed anyways.
Suggested-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Cc: Joe Perches <joe@perches.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Huth [Tue, 27 Aug 2013 15:09:02 +0000 (17:09 +0200)]
virtio-net: Set RXCSUM feature if GUEST_CSUM is available
If the VIRTIO_NET_F_GUEST_CSUM virtio feature is available, the guest
does not have to calculate the checksums on all received packets. This
is pretty much the same feature as RX checksum offloading on real
network cards, so the virtio-net driver should report this by setting
the NETIF_F_RXCSUM flag. When the user now runs "ethtool -k", he or she
can see whether the virtio-net interface has to calculate RX checksums
or not.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 4 Sep 2013 00:57:57 +0000 (20:57 -0400)]
Merge branch 'addr_assign_type'
Bjørn Mork says:
====================
net: set addr_assign_type when inheriting a dev_addr
Copying the dev_addr from a parent device is an operation
common to a number of drivers. The addr_assign_type should
be updated accordingly, either by reusing the value from
the source device or explicitly indicating that the address
is stolen by setting addr_assign_type to NET_ADDR_STOLEN.
This patch set adds a helper copying both the dev_addr and
the addr_assign_type, and use this helper in drivers which
don't currently set the addr_assign_type. Using NET_ADDR_STOLEN
might be more appropriate in some of these cases. Please
let me know, and I'll update the patch accordingly.
Changes in v2:
- assuming addr_len == ETH_ALEN to allow optimized memcpy
- dropped the vt6656 patch due to addr_len being unset in that driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 30 Aug 2013 16:08:52 +0000 (18:08 +0200)]
staging: vt6655: inherit addr_assign_type along with dev_addr
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Cc: Forest Bond <forest@alittletooquiet.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 30 Aug 2013 16:08:51 +0000 (18:08 +0200)]
net: libertas: inherit addr_assign_type along with dev_addr
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 30 Aug 2013 16:08:50 +0000 (18:08 +0200)]
net: hostap: inherit addr_assign_type along with dev_addr
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 30 Aug 2013 16:08:49 +0000 (18:08 +0200)]
net: airo: inherit addr_assign_type along with dev_addr
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 30 Aug 2013 16:08:48 +0000 (18:08 +0200)]
net: team: inherit addr_assign_type along with dev_addr
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 30 Aug 2013 16:08:47 +0000 (18:08 +0200)]
net: macvlan: inherit addr_assign_type along with dev_addr
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 30 Aug 2013 16:08:46 +0000 (18:08 +0200)]
net: dsa: inherit addr_assign_type along with dev_addr
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 30 Aug 2013 16:08:45 +0000 (18:08 +0200)]
net: vlan: inherit addr_assign_type along with dev_addr
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 30 Aug 2013 16:08:44 +0000 (18:08 +0200)]
net: etherdevice: add address inherit helper
Some etherdevices inherit their address from a parent or
master device. The addr_assign_type should be updated along
with the address in these cases. Adding a helper function
to simplify this.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 2 Sep 2013 02:06:53 +0000 (10:06 +0800)]
net: make snmp_mib_free static inline
Fengguang reported:
net/built-in.o: In function `in6_dev_finish_destroy':
(.text+0x4ca7d): undefined reference to `snmp_mib_free'
this is due to snmp_mib_free() is defined when CONFIG_INET is enabled,
but in6_dev_finish_destroy() is now moved to core kernel.
I think snmp_mib_free() is small enough to be inlined, so just make it
static inline.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 2 Sep 2013 02:06:52 +0000 (10:06 +0800)]
vxlan: include net/ip6_checksum.h for csum_ipv6_magic()
Fengguang reported a compile warning:
drivers/net/vxlan.c: In function 'vxlan6_xmit_skb':
drivers/net/vxlan.c:1352:3: error: implicit declaration of function 'csum_ipv6_magic' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
this patch fixes it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 2 Sep 2013 02:06:51 +0000 (10:06 +0800)]
vxlan: fix flowi6_proto value
It should be IPPROTO_UDP.
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 1 Sep 2013 02:35:26 +0000 (22:35 -0400)]
Merge branch 'qlcnic'
Shahed Shaikh says:
====================
This patch series contains -
* Enhanced PVID handling for 84xx adapters by
not indicating PVID configuration to VF driver and
keeping VF driver in no VLAN configuration mode becasue
adapter supports VLAN stripping.
* Removed inappropriate usage of inline keyword.
* Enhanced minidump feature by using firmware recommended
dump capture mask and using CAMRAM register to store
firmware dump state.
* AER handling support for 83xx adapter.
* Added support for per port eswitch configuration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shahed Shaikh [Fri, 30 Aug 2013 17:51:24 +0000 (13:51 -0400)]
qlcnic: Update version to 5.3.50
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sony Chacko [Fri, 30 Aug 2013 17:51:23 +0000 (13:51 -0400)]
qlcnic: Add support for per port eswitch configuration
There is an embedded switch per physical port on the adapter.
Add support for enabling and disabling the embedded switch
on per port basis.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pratik Pujar [Fri, 30 Aug 2013 17:51:22 +0000 (13:51 -0400)]
qlcnic: Restructuring of qlc_83xx_fw_info structure.
o Removed unused and unnecessary members from qlc_83xx_fw_info
structure.
o Made fw_info member of qlcnic_hardware_context as a pointer to
qlc_83xx_fw_info structure.
o Added a member fw_file_name to qlc_83xx_fw_info structure which
will hold the name of firmware image file name.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pratik Pujar [Fri, 30 Aug 2013 17:51:21 +0000 (13:51 -0400)]
qlcnic: Add AER support for 83xx adapter
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pratik Pujar [Fri, 30 Aug 2013 17:51:20 +0000 (13:51 -0400)]
qlcnic: Add AER callback handlers.
o Generic AER callback handlers will make use of qlcnic_hardware_ops structure
to call adapter specific handlers.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shahed Shaikh [Fri, 30 Aug 2013 17:51:19 +0000 (13:51 -0400)]
qlcnic: Store firmware dump state in CAMRAM register
-Use CAMRAM register to store firmware dump state in adapter
instead of maintaining it in each function driver separately.
-Return appropriate error code on failure
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shahed Shaikh [Fri, 30 Aug 2013 17:51:18 +0000 (13:51 -0400)]
qlcnic: Use firmware recommended dump capture mask as default
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Fri, 30 Aug 2013 17:51:17 +0000 (13:51 -0400)]
qlcnic: Remove inline keyword
o Remove inline keyword from function prototypes wherever it is not appropriate.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Fri, 30 Aug 2013 17:51:16 +0000 (13:51 -0400)]
qlcnic: Enhance PVID handling for 84xx adapters
o PF driver should not indicate PVID configuration to VF driver.
As adapter supports VLAN stripping, VF driver should stay agnostic
to any PVID configuration.
o Return "QLC_NO_VLAN_MODE(= 0)" to VFD when PVID is configured.
VF driver should be in no VLAN configuration mode.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sat, 31 Aug 2013 05:44:38 +0000 (13:44 +0800)]
net: unify skb_udp_tunnel_segment() and skb_udp6_tunnel_segment()
As suggested by Pravin, we can unify the code in case of duplicated
code.
Cc: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sat, 31 Aug 2013 05:44:37 +0000 (13:44 +0800)]
ipv6: Add generic UDP Tunnel segmentation
Similar to commit
731362674580cb0c696cd1b1a03d8461a10cf90a
(tunneling: Add generic Tunnel segmentation)
This patch adds generic tunneling offloading support for
IPv6-UDP based tunnels.
This can be used by tunneling protocols like VXLAN.
Cc: Jesse Gross <jesse@nicira.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sat, 31 Aug 2013 05:44:36 +0000 (13:44 +0800)]
vxlan: add ipv6 proxy support
This patch adds the IPv6 version of "arp_reduce", ndisc_send_na()
will be needed.
Cc: David S. Miller <davem@davemloft.net>
Cc: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sat, 31 Aug 2013 05:44:35 +0000 (13:44 +0800)]
ipv6: move in6_dev_finish_destroy() into core kernel
in6_dev_put() will be needed by vxlan module, so is
in6_dev_finish_destroy().
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sat, 31 Aug 2013 05:44:34 +0000 (13:44 +0800)]
vxlan: add ipv6 route short circuit support
route short circuit only has IPv4 part, this patch adds
the IPv6 part. nd_tbl will be needed.
Cc: David S. Miller <davem@davemloft.net>
Cc: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sat, 31 Aug 2013 05:44:33 +0000 (13:44 +0800)]
vxlan: add ipv6 support
This patch adds IPv6 support to vxlan device, as the new version
RFC already mentions it:
http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-03
Cc: David Stevens <dlstevens@us.ibm.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sat, 31 Aug 2013 05:44:32 +0000 (13:44 +0800)]
ipv6: do not call ndisc_send_rs() with write lock
Because vxlan module will call ip6_dst_lookup() in TX path,
which will hold write lock. So we have to release this write lock
before calling ndisc_send_rs(), otherwise could deadlock.
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sat, 31 Aug 2013 05:44:31 +0000 (13:44 +0800)]
ipv6: export in6addr_loopback to modules
It is needed by vxlan module. Noticed by Mike.
Cc: Mike Rapoport <mike.rapoport@ravellosystems.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sat, 31 Aug 2013 05:44:30 +0000 (13:44 +0800)]
ipv6: export a stub for IPv6 symbols used by vxlan
In case IPv6 is compiled as a module, introduce a stub
for ipv6_sock_mc_join and ipv6_sock_mc_drop etc.. It will be used
by vxlan module. Suggested by Ben.
This is an ugly but easy solution for now.
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sat, 31 Aug 2013 05:44:29 +0000 (13:44 +0800)]
ipv6: move ip6_local_out into core kernel
It will be used the vxlan kernel module.
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sat, 31 Aug 2013 05:44:28 +0000 (13:44 +0800)]
ipv6: move ip6_dst_hoplimit() into core kernel
It will be used by vxlan, and may not be inlined.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 1 Sep 2013 02:24:24 +0000 (22:24 -0400)]
Merge branch 'for-davem' of git://git./linux/kernel/git/bwh/sfc-next
Ben Hutchings says:
====================
1. A little more refactoring.
2. Remove the unnecessary use of atomic_t that you pointed out.
3. Add support for starting or queueing firmware requests from atomic
context.
4. Add hwmon support for additional sensors found on some new boards.
5. Add support for the EF10 controller architecture, the SFC9100 family
and specifically the SFC9120 controller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Sat, 31 Aug 2013 17:15:33 +0000 (10:15 -0700)]
qdisc: fix build with !CONFIG_NET_SCHED
Multiqueue scheduler refers to default_qdisc_ops; therefore the
variable definition needs to be moved to handle case where net
scheduler API is not available.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Sat, 31 Aug 2013 17:15:50 +0000 (10:15 -0700)]
qdisc: make args to qdisc_create_default const
Fixes warnings introduced by the qdisc default patch.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Tue, 27 Aug 2013 23:19:08 +0000 (16:19 -0700)]
qdisc: allow setting default queuing discipline
By default, the pfifo_fast queue discipline has been used by default
for all devices. But we have better choices now.
This patch allow setting the default queueing discipline with sysctl.
This allows easy use of better queueing disciplines on all devices
without having to use tc qdisc scripts. It is intended to allow
an easy path for distributions to make fq_codel or sfq the default
qdisc.
This patch also makes pfifo_fast more of a first class qdisc, since
it is now possible to manually override the default and explicitly
use pfifo_fast. The behavior for systems who do not use the sysctl
is unchanged, they still get pfifo_fast
Also removes leftover random # in sysctl net core.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 29 Aug 2013 08:25:14 +0000 (11:25 +0300)]
net/fec: cleanup types in fec_get_mac()
My static checker complains that on some arches unsigned longs can be 8
characters which is larger than the buffer is only 6 chars.
Additionally, Ben Hutchings points out that the buffer actually holds
big endian data and the buffer we are reading from is CPU endian.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:13:46 +0000 (14:13 +0900)]
net: stmmac: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:12:21 +0000 (14:12 +0900)]
net: macb: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:11:53 +0000 (14:11 +0900)]
net: at91_ether: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:09:26 +0000 (14:09 +0900)]
net: mdio-mux-gpio: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:08:55 +0000 (14:08 +0900)]
net: mdio-gpio: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:08:22 +0000 (14:08 +0900)]
net: ixp4xx_eth: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:07:38 +0000 (14:07 +0900)]
net: w5100: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:07:06 +0000 (14:07 +0900)]
net: w5300: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:06:41 +0000 (14:06 +0900)]
net: tsi108: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:06:02 +0000 (14:06 +0900)]
net: davinci_mdio: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 03:29:57 +0000 (12:29 +0900)]
net: davinci_emac: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:05:02 +0000 (14:05 +0900)]
net: cpmac: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:04:17 +0000 (14:04 +0900)]
net: niu: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:02:57 +0000 (14:02 +0900)]
net: smsc911x: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:02:06 +0000 (14:02 +0900)]
net: smc911x: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:01:35 +0000 (14:01 +0900)]
net: smc91x: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:00:45 +0000 (14:00 +0900)]
net: seeq: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 05:00:11 +0000 (14:00 +0900)]
net: sh_eth: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 04:59:34 +0000 (13:59 +0900)]
net: netx-eth: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 04:59:01 +0000 (13:59 +0900)]
net: ks8851-ml: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 04:58:30 +0000 (13:58 +0900)]
net: ks8842: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 04:58:00 +0000 (13:58 +0900)]
net: pxa168_eth: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 04:57:13 +0000 (13:57 +0900)]
net: mv643xx_eth: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 04:56:26 +0000 (13:56 +0900)]
net: fec: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 04:55:46 +0000 (13:55 +0900)]
net: ethoc: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 04:55:14 +0000 (13:55 +0900)]
net: dm9000: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 04:54:37 +0000 (13:54 +0900)]
net: ep93xx_eth: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 04:52:21 +0000 (13:52 +0900)]
net: bcm63xx_enet: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 04:51:45 +0000 (13:51 +0900)]
net: au1000_eth: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 04:50:48 +0000 (13:50 +0900)]
net: bfin_mac: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Fri, 30 Aug 2013 04:44:34 +0000 (13:44 +0900)]
net: ax88796: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lutz Jaenicke [Wed, 28 Aug 2013 11:34:31 +0000 (13:34 +0200)]
macvlan: fix typo in assignment
commit
3b04ddde02cf1b6f14f2697da5c20eca5715017f
"[NET]: Move hardware header operations out of netdevice."
moved the handling into macvlan setup adding
dev->header_ops = &macvlan_hard_header_ops,
At the end of the line the ',' should have been a ';'
Signed-off-by: Lutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sonic Zhang [Wed, 28 Aug 2013 10:55:39 +0000 (18:55 +0800)]
driver:net:stmmac: Disable DMA store and forward mode if platform data force_thresh_dma_mode is set.
Some synopsys ip implementation doesn't support DMA store and forward mode,
such as BF60x. So, set force_thresh_dma_mode to use DMA thresholds only.
Update document and devicetree as well.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Wed, 28 Aug 2013 10:05:38 +0000 (12:05 +0200)]
ipv6: Remove redundant sk variable
A sk variable initialized to ndisc_sk is already available outside
of the branch.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Fri, 30 Aug 2013 15:35:53 +0000 (08:35 -0700)]
tcp: do not use cached RTT for RTT estimation
RTT cached in the TCP metrics are valuable for the initial timeout
because SYN RTT usually does not account for serialization delays
on low BW path.
However using it to seed the RTT estimator maybe disruptive because
other components (e.g., pacing) require the smooth RTT to be obtained
from actual connection.
The solution is to use the higher cached RTT to set the first RTO
conservatively like tcp_rtt_estimator(), but avoid seeding the other
RTT estimator variables such as srtt. It is also a good idea to
keep RTO conservative to obtain the first RTT sample, and the
performance is insured by TCP loss probe if SYN RTT is available.
To keep the seeding formula consistent across SYN RTT and cached RTT,
the rttvar is twice the cached RTT instead of cached RTTVAR value. The
reason is because cached variation may be too small (near min RTO)
which defeats the purpose of being conservative on first RTO. However
the metrics still keep the RTT variations as they might be useful for
user applications (through ip).
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 30 Aug 2013 16:46:43 +0000 (09:46 -0700)]
pkt_sched: fq: prefetch() fix
kbuild bot reported following m68k build error :
net/sched/sch_fq.c: In function 'fq_dequeue':
>> net/sched/sch_fq.c:491:2: error: implicit declaration of function
'prefetch' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
While we are fixing this, move this prefetch() call a bit earlier.
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Tue, 27 Aug 2013 05:45:23 +0000 (22:45 -0700)]
drivers:net: Convert dma_alloc_coherent(...__GFP_ZERO) to dma_zalloc_coherent
__GFP_ZERO is an uncommon flag and perhaps is better
not used. static inline dma_zalloc_coherent exists
so convert the uses of dma_alloc_coherent with __GFP_ZERO
to the more common kernel style with zalloc.
Remove memset from the static inline dma_zalloc_coherent
and add just one use of __GFP_ZERO instead.
Trivially reduces the size of the existing uses of
dma_zalloc_coherent.
Realign arguments as appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 29 Aug 2013 22:49:55 +0000 (15:49 -0700)]
pkt_sched: fq: Fair Queue packet scheduler
- Uses perfect flow match (not stochastic hash like SFQ/FQ_codel)
- Uses the new_flow/old_flow separation from FQ_codel
- New flows get an initial credit allowing IW10 without added delay.
- Special FIFO queue for high prio packets (no need for PRIO + FQ)
- Uses a hash table of RB trees to locate the flows at enqueue() time
- Smart on demand gc (at enqueue() time, RB tree lookup evicts old
unused flows)
- Dynamic memory allocations.
- Designed to allow millions of concurrent flows per Qdisc.
- Small memory footprint : ~8K per Qdisc, and 104 bytes per flow.
- Single high resolution timer for throttled flows (if any).
- One RB tree to link throttled flows.
- Ability to have a max rate per flow. We might add a socket option
to add per socket limitation.
Attempts have been made to add TCP pacing in TCP stack, but this
seems to add complex code to an already complex stack.
TCP pacing is welcomed for flows having idle times, as the cwnd
permits TCP stack to queue a possibly large number of packets.
This removes the 'slow start after idle' choice, hitting badly
large BDP flows, and applications delivering chunks of data
as video streams.
Nicely spaced packets :
Here interface is 10Gbit, but flow bottleneck is ~20Mbit
cwin is big, yet FQ avoids the typical bursts generated by TCP
(as in netperf TCP_RR -- -r 100000,100000)
15:01:23.545279 IP A > B: . 78193:81089(2896) ack 65248 win 3125 <nop,nop,timestamp 1115
11597805>
15:01:23.545394 IP B > A: . ack 81089 win 3668 <nop,nop,timestamp
11597985 1115>
15:01:23.546488 IP A > B: . 81089:83985(2896) ack 65248 win 3125 <nop,nop,timestamp 1115
11597805>
15:01:23.546565 IP B > A: . ack 83985 win 3668 <nop,nop,timestamp
11597986 1115>
15:01:23.547713 IP A > B: . 83985:86881(2896) ack 65248 win 3125 <nop,nop,timestamp 1115
11597805>
15:01:23.547778 IP B > A: . ack 86881 win 3668 <nop,nop,timestamp
11597987 1115>
15:01:23.548911 IP A > B: . 86881:89777(2896) ack 65248 win 3125 <nop,nop,timestamp 1115
11597805>
15:01:23.548949 IP B > A: . ack 89777 win 3668 <nop,nop,timestamp
11597988 1115>
15:01:23.550116 IP A > B: . 89777:92673(2896) ack 65248 win 3125 <nop,nop,timestamp 1115
11597805>
15:01:23.550182 IP B > A: . ack 92673 win 3668 <nop,nop,timestamp
11597989 1115>
15:01:23.551333 IP A > B: . 92673:95569(2896) ack 65248 win 3125 <nop,nop,timestamp 1115
11597805>
15:01:23.551406 IP B > A: . ack 95569 win 3668 <nop,nop,timestamp
11597991 1115>
15:01:23.552539 IP A > B: . 95569:98465(2896) ack 65248 win 3125 <nop,nop,timestamp 1115
11597805>
15:01:23.552576 IP B > A: . ack 98465 win 3668 <nop,nop,timestamp
11597992 1115>
15:01:23.553756 IP A > B: . 98465:99913(1448) ack 65248 win 3125 <nop,nop,timestamp 1115
11597805>
15:01:23.554138 IP A > B: P 99913:100001(88) ack 65248 win 3125 <nop,nop,timestamp 1115
11597805>
15:01:23.554204 IP B > A: . ack 100001 win 3668 <nop,nop,timestamp
11597993 1115>
15:01:23.554234 IP B > A: . 65248:68144(2896) ack 100001 win 3668 <nop,nop,timestamp
11597993 1115>
15:01:23.555620 IP B > A: . 68144:71040(2896) ack 100001 win 3668 <nop,nop,timestamp
11597993 1115>
15:01:23.557005 IP B > A: . 71040:73936(2896) ack 100001 win 3668 <nop,nop,timestamp
11597993 1115>
15:01:23.558390 IP B > A: . 73936:76832(2896) ack 100001 win 3668 <nop,nop,timestamp
11597993 1115>
15:01:23.559773 IP B > A: . 76832:79728(2896) ack 100001 win 3668 <nop,nop,timestamp
11597993 1115>
15:01:23.561158 IP B > A: . 79728:82624(2896) ack 100001 win 3668 <nop,nop,timestamp
11597994 1115>
15:01:23.562543 IP B > A: . 82624:85520(2896) ack 100001 win 3668 <nop,nop,timestamp
11597994 1115>
15:01:23.563928 IP B > A: . 85520:88416(2896) ack 100001 win 3668 <nop,nop,timestamp
11597994 1115>
15:01:23.565313 IP B > A: . 88416:91312(2896) ack 100001 win 3668 <nop,nop,timestamp
11597994 1115>
15:01:23.566698 IP B > A: . 91312:94208(2896) ack 100001 win 3668 <nop,nop,timestamp
11597994 1115>
15:01:23.568083 IP B > A: . 94208:97104(2896) ack 100001 win 3668 <nop,nop,timestamp
11597994 1115>
15:01:23.569467 IP B > A: . 97104:100000(2896) ack 100001 win 3668 <nop,nop,timestamp
11597994 1115>
15:01:23.570852 IP B > A: . 100000:102896(2896) ack 100001 win 3668 <nop,nop,timestamp
11597994 1115>
15:01:23.572237 IP B > A: . 102896:105792(2896) ack 100001 win 3668 <nop,nop,timestamp
11597994 1115>
15:01:23.573639 IP B > A: . 105792:108688(2896) ack 100001 win 3668 <nop,nop,timestamp
11597994 1115>
15:01:23.575024 IP B > A: . 108688:111584(2896) ack 100001 win 3668 <nop,nop,timestamp
11597994 1115>
15:01:23.576408 IP B > A: . 111584:114480(2896) ack 100001 win 3668 <nop,nop,timestamp
11597994 1115>
15:01:23.577793 IP B > A: . 114480:117376(2896) ack 100001 win 3668 <nop,nop,timestamp
11597994 1115>
TCP timestamps show that most packets from B were queued in the same ms
timeframe (TSval
1159799{3,4}), but FQ managed to send them right
in time to avoid a big burst.
In slow start or steady state, very few packets are throttled [1]
FQ gets a bunch of tunables as :
limit : max number of packets on whole Qdisc (default 10000)
flow_limit : max number of packets per flow (default 100)
quantum : the credit per RR round (default is 2 MTU)
initial_quantum : initial credit for new flows (default is 10 MTU)
maxrate : max per flow rate (default : unlimited)
buckets : number of RB trees (default : 1024) in hash table.
(consumes 8 bytes per bucket)
[no]pacing : disable/enable pacing (default is enable)
All of them can be changed on a live qdisc.
$ tc qd add dev eth0 root fq help
Usage: ... fq [ limit PACKETS ] [ flow_limit PACKETS ]
[ quantum BYTES ] [ initial_quantum BYTES ]
[ maxrate RATE ] [ buckets NUMBER ]
[ [no]pacing ]
$ tc -s -d qd
qdisc fq 8002: dev eth0 root refcnt 32 limit 10000p flow_limit 100p buckets 256 quantum 3028 initial_quantum 15140
Sent
216532416 bytes 148395 pkt (dropped 0, overlimits 0 requeues 14)
backlog 0b 0p requeues 14
511 flows, 511 inactive, 0 throttled
110 gc, 0 highprio, 0 retrans, 1143 throttled, 0 flows_plimit
[1] Except if initial srtt is overestimated, as if using
cached srtt in tcp metrics. We'll provide a fix for this issue.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 29 Aug 2013 22:32:48 +0000 (23:32 +0100)]
sfc: Update copyright banners
Update the dates for files that have been added to in 2012-2013.
Drop the 'Solarstorm' brand name that's still lingering here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Oliver Hartkopp [Mon, 26 Aug 2013 13:05:36 +0000 (15:05 +0200)]
can: gw: add a per rule limitation of frame hops
Usually the received CAN frames can be processed/routed as much as 'max_hops'
times (which is given at module load time of the can-gw module).
Introduce a new configuration option to reduce the number of possible hops
for a specific gateway rule to a value smaller then max_hops.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Gerhard Sittig [Fri, 23 Aug 2013 11:09:03 +0000 (13:09 +0200)]
can: mscan: improve clock API use
the .get_clock() callback is run from probe() and might allocate
resources, introduce a .put_clock() callback that is run from remove()
to undo any allocation activities
prepare and enable the clocks in open(), disable and unprepare the
clocks in close() if clocks were acquired during probe(), to not assume
knowledge about which activities are done in probe() and remove()
use devm_get_clk() to lookup the SYS and REF clocks, to have the clocks
put upon device shutdown
store pointers to data structures upon successful allocation already
instead of deferral until complete setup, such that subroutines in the
setup sequence may access those data structures as well to track their
resource acquisition
since clock allocation remains optional, the release callback as well as
the enable/disable calls in open/close are optional as well
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Gerhard Sittig [Fri, 23 Aug 2013 11:09:02 +0000 (13:09 +0200)]
can: mscan: add a comment on reg to idx mapping
add a comment about the magic of deriving an MSCAN component index
from the peripheral's physical address / register offset
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Daniel Borkmann [Wed, 28 Aug 2013 20:13:11 +0000 (22:13 +0200)]
net: packet: document available fanout policies
Update documentation to add fanout policies that are available.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 28 Aug 2013 20:13:10 +0000 (22:13 +0200)]
net: packet: use reciprocal_divide in fanout_demux_hash
Instead of hard-coding reciprocal_divide function, use the inline
function from reciprocal_div.h.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 28 Aug 2013 20:13:09 +0000 (22:13 +0200)]
net: packet: add randomized fanout scheduler
We currently allow for different fanout scheduling policies in pf_packet
such as scheduling by skb's rxhash, round-robin, by cpu, and rollover.
Also allow for a random, equidistributed selection of the socket from the
fanout process group.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Thu, 29 Aug 2013 20:24:47 +0000 (00:24 +0400)]
sh_eth: no need to call ether_setup()
There's no need to call ether_setup() in the driver since prior alloc_etherdev()
call already arranges for it.
Suggested-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 29 Aug 2013 20:19:50 +0000 (16:19 -0400)]
Merge branch 'bond_vlan'
Veaceslav Falico says:
====================
bonding: remove vlan special handling
v1: Per Jiri's advice, remove the exported netdev_upper struct to keep it
inside dev.c only, and instead implement a macro to iterate over the
list and return only net_device *.
v2: Jiri noted that we need to see every upper device, but not only the
first level. Modify the netdev_upper logic to include a list of lower
devices and for both upper/lower lists every device would see both its
first-level devices and every other devices that is lower/upper of it.
Also, convert some annoying spamming warnings to pr_debug in
bond_arp_send_all.
v3: move renaming part completely to patch 1 (did I forget to git add
before commiting?) and address Jiri's input about comments/style of
patch 2.
v4: as Vlad found spotted, bond_arp_send_all() won't work in a config where
we have a device with ip on top of our upper vlan. It fails to send
packets because we don't tag the packet, while the device on top of
vlan will emit tagged packets through this vlan. Fix this by first
searching for all upper vlans, and for each vlan - for the devs on top
of it. If we find the dev - then tag the packet with the underling's
vlan_id, otherwise just search the old way - for all devices on top of
bonding. Also, move the version changes under "---" so they won't get
into the commit message, if/when applied.
The aim of this patchset is to remove bondings' own vlan handling as much
as possible and replace it with the netdev upper device functionality.
The upper device functionality is extended to include also lower devices
and to have, for each device, a full view of every lower and upper device,
but not only the first-level ones. This might permit in the future to
avoid, for any grouping/teaming/upper/lower devices, to maintain its own
lists of slaves/vlans/etc.
This is achieved by adding a helper function to upper dev list handling -
netdev_upper_get_next_dev(dev, iter), which returns the next device after
the list_head **iter, and sets *iter to the next list_head *. This patchset
also adds netdev_for_each_upper_dev(dev, upper, iter), which iterates
through the whole dev->upper_dev_list, setting upper to the net_device.
The only special treatment of vlans remains in rlb code.
This patchset solves several issues with bonding, simplifies it overall,
RCUify further and exports upper list functions for any other users which
might also want to get rid of its own vlan_lists or slaves.
I'm testing it continuously currently, no issues found, will update on
anything.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Veaceslav Falico [Wed, 28 Aug 2013 21:25:16 +0000 (23:25 +0200)]
bonding: pr_debug instead of pr_warn in bond_arp_send_all
They're simply annoying and will spam dmesg constantly if we hit them, so
convert to pr_debug so that we still can access them in case of debugging.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Veaceslav Falico [Wed, 28 Aug 2013 21:25:15 +0000 (23:25 +0200)]
bonding: remove vlan_list/current_alb_vlan
Currently there are no real users of vlan_list/current_alb_vlan, only the
helpers which maintain them, so remove them.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>