git.osdn.net Git - uclinux-h8/linux.git/log

drm/i915/icl: Fix MG PLL setup when refclk is 38.4MHz

Atm we're zeroing out fields in MG_PLL_BIAS and MG_PLL_TDC_COLDST_BIAS
if refclk is 38.4MHz, whereas the spec tells us to preserve them.
Although the calculated values mostly match the register defaults even
for the 38.4MHz case, there are some differences wrt. what BIOS
programs (I noticed at least differences in the MG_PLL_BIAS/IREFTRIM and
MG_PLL_BIAS/BIASCAL_EN fields). In the lack of further info on how to
program these fields, just do what the spec says and preserve the BIOS
state.

v2:
- Preserve the BIOS programmed reg fields instead of programming them.

Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com> (v1)
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615143911.31082-1-imre.deak@intel.com

drm/i915: remove check for aux irq

This became dead code with commit 309bd8ed464f ("drm/i915: Reinstate
GMBUS and AUX interrupts on gen4/g4x").

v2: Move comment about HW behavior to where decision is made to enable
MSI (Ville).

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180523180435.18042-1-lucas.demarchi@intel.com

drm/i915: Redefine EINVAL for debugging

To aide debugging spurious EINVALs, include a debug message every time
we emit one from execbuf.

References: https://bugs.freedesktop.org/show_bug.cgi?id=106744
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621080150.8110-1-chris@chris-wilson.co.uk

drm/i915: Ignore applying the self-relocation BIAS if no relocations

We only need to apply the BIAS for self-relocations into the batchbuffer
iff the execobject has any relocations.

This suppresses some warnings we may get with a full gtt (so the batch
object has wound up at 0 from a previous invocation), but doesn't fix
the underlying problem of how we tried to move a pinned batch vma (how
we have a pinned user vma outside of execbuf, I do not know, though this
being on an aliasing ppgtt means it could be a spurious pinning via the
global gtt). One step at a time...

References: https://bugs.freedesktop.org/show_bug.cgi?id=106744#c1
Testcase: igt/gem_exec_gttfill # byt (sporadic)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621073205.26701-1-chris@chris-wilson.co.uk

drm/i915: Disable bh around call to tasklet

The guc submission backends expects to only be run from (at least)
softirq context, but during our intel_engine_is_idle() check we would
call into the tasklet to make sure it was flushed. As this could occur
from process context, occasionally we would be caught out using a
wait_for_atomic() not from an atomic context:

[   59.939091] WARN_ON_ONCE((1) && !(preempt_count() != 0))
[   59.939142] WARNING: CPU: 1 PID: 2901 at drivers/gpu/drm/i915/intel_guc_submission.c:615 guc_submission_tasklet+0x784/0xa90 [i915]
[   59.939143] Modules linked in: vgem snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic i915 x86_pkg_temp_thermal intel_powerclamp coretemp crct10dif_pclmul snd_hda_intel crc32_pclmul snd_hda_codec ghash_clmulni_intel snd_hwdep snd_hda_core e1000e snd_pcm mei_me mei prime_numbers
[   59.939164] CPU: 1 PID: 2901 Comm: gem_exec_schedu Tainted: G     U  W         4.18.0-rc1-g93475d62c730-drmtip_67+ #1
[   59.939165] Hardware name: System manufacturer System Product Name/Z170M-PLUS, BIOS 3610 03/29/2018
[   59.939188] RIP: 0010:guc_submission_tasklet+0x784/0xa90 [i915]
[   59.939189] Code: fc ff ff 80 3d 2f 87 11 00 00 0f 85 80 fb ff ff 48 c7 c6 f8 49 40 c0 48 c7 c7 80 41 3e c0 c6 05 14 87 11 00 01 e8 2c ea d6 d3 <0f> 0b e9 5f fb ff ff 8b 46 38 89 cf 31 c7 83 e7 c0 75 08 39 c1 0f
[   59.939253] RSP: 0018:ffffaafe08a03c10 EFLAGS: 00010286
[   59.939255] RAX: 0000000000000000 RBX: ffff8f9112c246f0 RCX: 0000000000000001
[   59.939256] RDX: 0000000080000001 RSI: ffffffff95086d8e RDI: 00000000ffffffff
[   59.939257] RBP: ffff8f9112c24680 R08: 000000009517be77 R09: 0000000000000000
[   59.939258] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8f9112c24700
[   59.939259] R13: ffff8f9112c24700 R14: 0000000000000000 R15: ffff8f9112c242a8
[   59.939260] FS:  00007fc2cc7e5980(0000) GS:ffff8f9136c40000(0000) knlGS:0000000000000000
[   59.939261] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   59.939262] CR2: 00007fc2cc815040 CR3: 000000021f10e003 CR4: 00000000003606e0
[   59.939263] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   59.939264] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   59.939265] Call Trace:
[   59.939288]  ? intel_engine_is_idle+0x64/0x160 [i915]
[   59.939323]  ? intel_engine_dump+0x638/0x890 [i915]
[   59.939327]  ? seq_printf+0x49/0x70
[   59.939353]  ? i915_engine_info+0xc8/0x100 [i915]
[   59.939356]  ? drm_get_color_range_name+0x20/0x20
[   59.939361]  ? seq_read+0xf1/0x470
[   59.939365]  ? trace_hardirqs_on_caller+0xe0/0x1b0
[   59.939370]  ? full_proxy_read+0x51/0x80
[   59.939389]  ? __vfs_read+0x31/0x170
[   59.939395]  ? do_sys_open+0x13b/0x240
[   59.939398]  ? rcu_read_lock_sched_held+0x6f/0x80
[   59.939401]  ? vfs_read+0x9e/0x140
[   59.939404]  ? ksys_read+0x50/0xc0
[   59.939409]  ? do_syscall_64+0x55/0x190
[   59.939412]  ? entry_SYSCALL_64_after_hwframe+0x49/0xbe
[   59.939420] irq event stamp: 552834
[   59.939422] hardirqs last  enabled at (552833): [<ffffffff940fc74c>] console_unlock+0x3fc/0x600
[   59.939425] hardirqs last disabled at (552834): [<ffffffff94a0111c>] error_entry+0x7c/0x100
[   59.939451] softirqs last  enabled at (552614): [<ffffffffc02e0f53>] i915_request_add+0x2e3/0x7b0 [i915]
[   59.939470] softirqs last disabled at (552604): [<ffffffffc02e0ecb>] i915_request_add+0x25b/0x7b0 [i915]

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106977
Fixes: dd0cf235d81f ("drm/i915: Speed up idle detection by kicking the tasklets")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180620135929.23956-1-chris@chris-wilson.co.uk

drm/i915: Update DRIVER_DATE to 20180620

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915/icl: Add 10-bit support for hdmi

Starting Icelake silicon supports 10-bpc hdmi to support certain
media workloads. Currently hdmi supports 8 and 12 bpc. Plumbed
in support for 10 bit hdmi.

Cc: James Ausmus <james.ausmus@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180522002558.29262-18-paulo.r.zanoni@intel.com

drm/i915/psr: fix copy-paste error with setting of tp2_wakeup_time_us

Currently for the psr_table->tp2_tp3_wakeup_time case 3 there appears
to be a copy-paste error from the previous switch statement where
dev_priv->vbt.psr.tp1_wakeup_time_us is being assigned and I believe
it should be dev_priv->vbt.psr.tp2_tp3_wakeup_time_us that should be
assigned instead.

Detected by CoverityScan, CID#1470105 ("Copy-paste error")

Fixes: 77312ae8f071 ("drm/i915/psr: vbt change for psr")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180620132543.28092-1-colin.king@canonical.com

drm/i915/psr: Fix warning in intel_psr_activate()

commit 5422b37c907e ("drm/i915/psr: Kill delays when activating psr
back.") removed the call to cancel a scheduled psr_work from
psr_disable() and instead added an early return in the work function. But,
if the scheduled work item is executed after psr_enable(), we end up
printing warnings as PSR is already enabled and active. So, put the
cancel_work call back in psr_disable().

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Fixes: 5422b37c907e ("drm/i915/psr: Kill delays when activating psr back.")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106948
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618220207.2778-1-dhinakaran.pandiyan@intel.com

drm/i915/selftests: Avoid ERR_PTR dereference

Along the early error path for igt_switch_to_kernel_context we may try
to dereference an invalid error pointer. Instead, return early rather
than dump the GEM trace since we haven't yet emitted anything of
interest.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 09a4c02e58c1 ("drm/i915: Look for an active kernel context before switching")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180620112441.13085-1-chris@chris-wilson.co.uk

Merge tag 'gvt-next-2018-06-19' of https://github.com/intel/gvt-linux into drm-intel-next-queued

gvt-next-2018-06-19

- fine-grained per vgpu locking (Colin)
- fine-grained vgpu scheduler locking (Colin)
- deliver windows guest cursor hotspot info (Tina)
- GVT-g BXT support (Colin)
- other misc and checker fixes (Chris, Xinyun)

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180619090043.ly6gquafbmxuus6h@zhen-hp.sh.intel.com

drm/i915/audio: constify ELD pointers

The hooks aren't supposed to modify the ELD, so use const pointer. As a
drive-by fix, use drm_eld_size() to log ELD size.

Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180619124437.10982-1-jani.nikula@intel.com

drm/i915: Enforce max hdisplay/hblank_start limits on HSW/BDW FDI

The PCH transcoder registers are only 12 bits wide for the hdisplay
and hblank_start values. On HSW/BDW the CPU side registers are 13
bits wide. intel_mode_valid() only checks against the higher limit
(since we don't know where the mode is to be used), so an extra
check is required against the FDI limits.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615174406.12258-3-ville.syrjala@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>

drm/i915: Check timings against hardware maximums

Validate that all display timings fit within the number of bits
we have in the transcoder timing registers.

The limits are:
hsw+:
4k: vdisplay, vblank_start
8k: everything else
gen3+:
4k: h/vdisplay, h/vblank_start
8k: everything else
gen2:
2k: h/vdisplay, h/vblank_start
4k: everything else

Also document the fact that the mode_config.max_width/height limits
refer to just the max framebuffer dimensions we support. Which may
be larger than the max hdisplay/vdisplay.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615174406.12258-2-ville.syrjala@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>

drm/i915: Nuke the cursor size defines

No point in having this extra indireciton for the cursor max size.
So drop the defines and just write out the raw numbers. Makes it
easier to see what's going on.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615174406.12258-1-ville.syrjala@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>

drm/i915: Print prop name/id when rejecting it

Use the '[PROP:id:name]' format I introduced for the core in the driver
debug messages as well.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611193403.16118-3-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/psr: Adds psrwake options for all platforms

Adds new psrwake options defined in the below table.
Platform PSR wake options vbt version
KBL/CFL/WHL All(205+)
BXT Uses old interpretation.
CNL/ICL+ All(205+)
GLK All(205+)
SKL All PV releases (Check for 205+ might help but cannot be foolproof)

We will continue with newer interpretation for SKL from 205.

v2: Jani
    Keep the bdb version check.
v3:
    Apply newer version for skl from 205+(DK).
    Add (version check && platform list) (Jani).
    Add bdb version for each platform in commit message(DK).

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Puthikorn Voravootivat <puthik@chromium.org>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ashutosh D Shukla <ashutosh.d.shukla@intel.com>
Cc: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1529302326-3567-1-git-send-email-vathsala.nagaraju@intel.com

i915: remove timespec_to_jiffies_timeout

This function has been unused since commit 5ed0bdf21a85 ("drm: i915:
Use nsec based interfaces"). Let's remove the definition as well now
to help get rid of all uses of 'timespec'.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618153855.2126048-1-arnd@arndb.de

drm/i915/icl: Handle hotplug interrupts for DP over TBT

This patch enables hotplug interrupts for DP over TBT output on TC
ports. The TBT interrupts are enabled and handled irrespective of the
actual output type which could be DP Alternate, DP over TBT, native DP
or native HDMI.

Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180616000530.5357-3-paulo.r.zanoni@intel.com

drm/i915/icl: Support for TC North Display interrupts

The hotplug interrupts for the ports can be routed to either North
Display or South Display depending on the output mode. DP Alternate or
DP over TBT outputs will have hotplug interrupts routed to the North
Display while interrupts for legacy modes will be routed to the South
Display in PCH. This patch adds hotplug interrupt handling support for
DP Alternate mode.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
[Paulo: coding style changes]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180616000530.5357-2-paulo.r.zanoni@intel.com

drm/i915/icl: GSE interrupt moves from DE_MISC to GU_MISC

The Graphics System Event(GSE) interrupt bit has a new location in the
GU_MISC_INTERRUPT_{IIR, ISR, IMR, IER} registers. Since GSE was the only
DE_MISC interrupt that was enabled, with this change we don't enable/handle
any of DE_MISC interrupts for gen11. Credits to Paulo for pointing out
the register change.

v2: from DK
raw_reg_[read/write], branch prediction hint and drop platform check (Mika)

v3: From DK
Early re-enable of master interrupt (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
[Paulo: bikesheds and rebases]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180616000530.5357-1-paulo.r.zanoni@intel.com

drm/i915/i915_reg.h: fix the checkpatch MACRO_ARG_PRECEDENCE issues

While I don't see any issue with the way these macros are being called
today, let's protect them against operator precedence issues before
they happen.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612235654.7914-4-paulo.r.zanoni@intel.com

drm/i915/i915_reg.h: fix the checkpatch SPACE_BEFORE_TAB issues

Since I'm touching the file I might as well fix this class of errors
since they are just a few. Also drive-by fix the styling of the
VLV_TURBO_SOC_OVERRIDE definitions instead of just the spaces before
the tabs.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612235654.7914-3-paulo.r.zanoni@intel.com

drm/i915/i915_reg.h: fix the checkpatch SPACING issues

Because OCD.

Now seriously, commit 1aa920ea0e85 ("drm/i915: add register macro
definition style guide") has finally established a coding standard to
be followed by the rest of the file, and I've been trying to request
everybody to adhere to that since then. The problem is that when
someone adds a new line to a register that has the wrong style, these
people generally propagate the wrong style and I have to keep asking
them to drive-by fix the whole register, which is not something I like
to do and also creates extra work for them. Or I can ignore the
propagation of the wrong coding style and feel anxious about it. On
top of that, we now have our CI happily reminding us about these
problems, which makes everything worse.

So IMHO the best way to proceed is to fix the spacing issues in the
file once and for all. Contributors will stop propagating the bad
style when adding new bits to registers that already have bad style,
we will stop asking them to redo their patches and the CI emails will
become more relevant by having less semi-false errors.

Yes, there will be some pain involved for backporters, but at least
spacing issues like that are easy to spot and fix in the patch files.

This patch was generated by:

../../../../scripts/checkpatch.pl -f --strict --types SPACING \
--fix-inplace i915_reg.h

I manually checked the output and everything seems sane.

v2: Single conflict around the addition of DP_TP_CTL_LINK_TRAIN_PAT4.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618180943.894-1-paulo.r.zanoni@intel.com

drm/i915/audio: Add 810 MHz clock entries to dp_aud_n_m table

Expand the Maud/Naud table according to DP 1.4 spec to include entries for
810 MHz clock. This is required for audio to work with HBR3.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180607192013.25872-1-radhakrishna.sripada@intel.com

drm/i915/aml: Introducing Amber Lake platform

Amber Lake uses the same gen graphics as Kaby Lake, including a id
that were previously marked as reserved on Kaby Lake, but that
now is moved to AML page.

So, let's just move it to AML macro that will feed into KBL macro
just to keep it better organized to make easier future code review
but it will be handled as a KBL.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614233720.30517-2-jose.souza@intel.com

drm/i915/whl: Introducing Whiskey Lake platform

Whiskey Lake uses the same gen graphics as Coffe Lake, including some
ids that were previously marked as reserved on Coffe Lake, but that
now are moved to WHL page.

So, let's just move them to WHL macros that will feed into CFL macro
just to keep it better organized to make easier future code review
but it will be handled as a CFL.

v2:
Fixing GT level of some ids

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614233720.30517-1-jose.souza@intel.com

drm/i915/execlists: Pull the w/a LRI emission into a helper

Having the w/a registers as an open-coded table leaves a trap for the
unwary; it would be easy to miss incrementing the LRI counter when
adding a new register to the list. Instead, pull the list of registers
into a table, so that we only need add new registers to that table
rather than try and remember important side-effects of earlier chunks of
GPU instructions.

Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618094150.30895-1-chris@chris-wilson.co.uk

drm/i915: Only show debug for state changes when banning

Since we trigger 10,000s of hangs and resets during selftesting, we emit
many, many thousands of lines of useless debug messages. Reduce the
frequency by only logging a change in state of a guilty context.

Fixes: 14921f3cef85 ("drm/i915: Fix context ban and hang accounting for client")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618073135.10849-1-chris@chris-wilson.co.uk

drm/i915/lspcon: switch to kernel unsigned int types

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1e132575785d9b615208eb60ee5e388df5991172.1528794959.git.jani.nikula@intel.com

drm/i915/audio: switch to kernel unsigned int types

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/808b06e1f0a95a4ee892553abf11fdbc30025571.1528794959.git.jani.nikula@intel.com

drm/i915/backlight: switch to kernel unsigned int types

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e68c3f16738eb3ab9f276d797f20326ed6d15848.1528794959.git.jani.nikula@intel.com

drm/i915/dvo: switch to kernel unsigned int types

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.

v2: fix checkpatch warning on indentation

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612095621.21101-1-jani.nikula@intel.com

drm/i915/uncore: switch to kernel unsigned int types

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4af5f30fc9665d1bed1eed09e7f749737749d739.1528794959.git.jani.nikula@intel.com

drm/i915/hdmi: switch to kernel unsigned int types

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d8b79de3d52e1fcaeabf3abfbb2ed99c4397ff2b.1528794959.git.jani.nikula@intel.com

drm/i915/vbt: switch to kernel unsigned int types

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ed5de29c280797b20eb625d52592dcbba8326684.1528794959.git.jani.nikula@intel.com

drm/i915: Fix fallout of fake reset along resume

commit b2209e62a450 ("drm/i915/execlists: Reset the CSB head tracking on
reset/sanitization") and commit 1288786b18f7 ("drm/i915: Move GEM sanitize
from resume_early to resume") show the conflicting requirements on the
code. We must reset the GPU before trashing live state on a fast resume
(hibernation debug, or error paths), but we must only reset our state
tracking iff the GPU is reset (or power cycled). This is tricky if we
are disabling GPU reset to simulate broken hardware; we reset our state
tracking but the GPU is left intact and recovers from its stale state.

v2: Again without the assertion for forcewake, no longer required since
commit b3ee09a4de33 ("drm/i915/ringbuffer: Fix context restore upon reset")
as the contexts are reset from the CS ensuring everything is powered up.

Fixes: b2209e62a450 ("drm/i915/execlists: Reset the CSB head tracking on reset/sanitization")
Fixes: 1288786b18f7 ("drm/i915: Move GEM sanitize from resume_early to resume")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180616202534.18767-1-chris@chris-wilson.co.uk

drm/i915: Enable provoking vertex fix on Gen9 systems.

The SF and clipper units mishandle the provoking vertex in some cases,
which can cause misrendering with shaders that use flat shaded inputs.

There are chicken bits in 3D_CHICKEN3 (for SF) and FF_SLICE_CHICKEN
(for the clipper) that work around the issue. These registers are
unfortunately not part of the logical context (even the power context),
and so we must reload them every time we start executing in a context.

Bugzilla: https://bugs.freedesktop.org/103047
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615190605.16238-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org

drm/i915/icl: update VBT's child_device_config flags2 field

Some bits from the flags2 field are going to be used in the next
patches, so replace the whole-byte definition with the actual bits and
document their versions.

This patch is based on a patch by Animesh Manna.

Cc: Animesh Manna <animesh.manna@intel.com>
Credits-to: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614221018.19044-2-paulo.r.zanoni@intel.com

drm/i915/icl: implement DVFS for ICL

ICL DVFS is almost the same as CNL, except for the CDCLK/DDICLK
table. Implement it just like CNL does.

References: commit 48469eced282 ("drm/i915: Use cdclk_state->voltage
on CNL")
References: commit 53e9bf5e8159 ("drm/i915: Adjust system agent
voltage on CNL if required by DDI ports")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614221018.19044-1-paulo.r.zanoni@intel.com

drm/i915: s/IS_G4X && !IS_GM45/IS_G45/

We have IS_G45 these days. Let's use it instead of the
'IS_G4X && !IS_GM45' construct.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614180500.2565-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/execlists: Reset the CSB head tracking on reset/sanitization

We can avoid the mmio read of the CSB pointers after reset based on the
knowledge that the HW always start writing at entry 0 in the CSB buffer.
We need to reset our CSB head tracking after GPU reset (and on
sanitization after resume) so that we are expecting to read from entry
0, hence we reset our head tracking back to the entry before (the last
entry in the ring).

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615093137.14270-2-chris@chris-wilson.co.uk

drm/i915: Be irqsafe inside reset

As we want to be able to call i915_reset_engine and co from a softirq or
timer context, we need to be irqsafe at all times. So we have to forgo
the simple spin_lock_irq for the full spin_lock_irqsave.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615093137.14270-1-chris@chris-wilson.co.uk

drm/i915: Fix context ban and hang accounting for client

If client is smart or lucky enough to create a new context
after each hang, our context banning mechanism will never
catch up, and as a result of that it will be saved from
client banning. This can result in a never ending streak of
gpu hangs caused by bad or malicious client, preventing
access from other legit gpu clients.

Fix this by always incrementing per client ban score if
it hangs in short successions regardless of context ban
scoring. The exception are non bannable contexts. They remain
detached from client ban scoring mechanism.

v2: xchg timestamp, tidyup (Chris)
v3: comment, bannable & banned together (Chris)

Fixes: b083a0870c79 ("drm/i915: Add per client max context ban limit")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615104429.31477-1-mika.kuoppala@linux.intel.com

drm/i915: Keep the ctx workarounds tightly packed

For each platform, we have a few registers that are rewritten with
different values -- they are not part of a sequence, just different parts
of a masked register set at different times (e.g. platform and gen
workarounds). Consolidate these into a single register write to keep the
table compact, important since we are running of room in the current
fixed sized buffer.

While adjusting the construction of the wa table, make it non fatal so
that the driver still loads but keeping the warning and extra details
for inspection.

Inspecting the changes for a Kabylake system,
Before:
Address val mask read
0x07014 0x20002000 0x00002000 0x00002100
0x0E194 0x01000100 0x00000100 0x00000114
0x0E4F0 0x81008100 0x00008100 0xFFFF8120
0x0E184 0x00200020 0x00000020 0x00000022
0x0E194 0x00140014 0x00000014 0x00000114
0x07004 0x00420042 0x00000042 0x000029C2
0x0E188 0x00080000 0x00000008 0x00008030
0x07300 0x80208020 0x00008020 0x00008830
0x07300 0x00100010 0x00000010 0x00008830
0x0E184 0x00020002 0x00000002 0x00000022
0x0E180 0x20002000 0x00002000 0x00002000
0x02580 0x00010000 0x00000001 0x00000004
0x02580 0x00060004 0x00000006 0x00000004
0x07014 0x01000100 0x00000100 0x00002100
0x0E100 0x00100010 0x00000010 0x00008050

After:
Address val mask read
0x02580 0x00070004 0x00000007 0x00000004
0x07004 0x00420042 0x00000042 0x000029C2
0x07014 0x21002100 0x00002100 0x00002100
0x07300 0x80308030 0x00008030 0x00008830
0x0E100 0x00100010 0x00000010 0x00008050
0x0E180 0x20002000 0x00002000 0x00002000
0x0E184 0x00220022 0x00000022 0x00000022
0x0E188 0x00080000 0x00000008 0x00008030
0x0E194 0x01140114 0x00000114 0x00000114
0x0E4F0 0x81008100 0x00008100 0xFFFF8120

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615120207.13952-1-chris@chris-wilson.co.uk

drm/i915/dp: Add support for HBR3 and TPS4 during link training

DP spec 1.4 supports training pattern set 4 (TPS4) for HBR3 link
rate. This will be used in link training's channel equalization
phase if supported by both source and sink.
This patch adds the helpers to check if HBR3 is supported and uses
TPS4 in training pattern selection during link training.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611222655.5696-2-paulo.r.zanoni@intel.com

drm/i915/icl: Add allowed DP rates for Icelake

For ICL, on Combo PHY the allowed max rates are:
- HBR3 8.1 eDP (DDIA)
- HBR2 5.4 DisplayPort (DDIB)
and for MG PHY/TC DDI Ports allowed DP rates are:
- HBR3 8.1 DisplayPort (DP alternate mode, DP over TBT,
- DP on legacy connector - DDIC/D/E/F)

v2 (from Paulo): Remove misleading comment (Ville).

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
[Paulo: bikeshed to keep future platforms on "else", v2.]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611222655.5696-1-paulo.r.zanoni@intel.com

drm/i915/icl: start adding the TBT pll

This commit just adds the register addresses and the basic skeleton of
the code. The next commits will expand on more specific functions.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180522002558.29262-15-paulo.r.zanoni@intel.com

drm/i915/icl: unconditionally init DDI for every port

On ICP, port present straps (from SFUSE_STRAP PCH register) are no
longer supported. Software should determine the presence through BIOS
VBT, hotplug or other mechanisms.

v2: Improve commit message (Lucas).

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180522002558.29262-14-paulo.r.zanoni@intel.com

drm/i915/icl: add icelake_get_ddi_pll()

Implement the hardware state readout code.

Thanks to Animesh Manna for spotting this problem.

Cc: Animesh Manna <animesh.manna@intel.com>
Credits-to: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180522002558.29262-11-paulo.r.zanoni@intel.com

drm/i915/gtt: Reduce a pair of runtime asserts

We can stop asserting using WARN_ON as given sufficient CI coverage, we
can rely on using GEM_BUG_ON() to catch problems before merging.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614184218.1606-2-chris@chris-wilson.co.uk

drm/i915/gtt: Cache the PTE encoding of the scratch page

As the most frequent PTE encoding is for the scratch page, cache it upon
creation.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614184218.1606-1-chris@chris-wilson.co.uk

drm/i915/gtt: Free unused page tables on unbind the context

As we cannot reliably change used page tables while the context is
active, the earliest opportunity we have to recover excess pages is when
the context becomes idle. So whenever we unbind the context (it must be
idle, and indeed being evicted) free the unused ptes.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614134315.5900-2-chris@chris-wilson.co.uk

drm/i915/gtt: Lazily allocate page directories for gen7

As we were only supporting aliasing_ppgtt on gen7 for some time, we
saved a few checks by preallocating the page directories on creation.
However, since we need 2MiB of page directories for each ppgtt, to
support arbitrary numbers of user contexts, we need to be more prudent
in our allocations, and defer the page allocation until it is used. We
don't recover unused pages yet as we found that doing so on the fly
(i.e. altering TLB entries) would confuse the GPU.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614134315.5900-1-chris@chris-wilson.co.uk

drm/i915: Declare the driver wedged if hangcheck makes no progress

Hangcheck is our back up in case the GPU or the driver gets stuck. It
detects when the GPU is not making any progress and issues a GPU reset.
However, if the driver is failing to make any progress, we can get
ourselves into a situation where we continually try resetting the GPU to
no avail. Employ a second timeout such that if we continue to see the
same seqno (the stalled engine has made no progress at all) over the
course of several hangchecks, declare the driver wedged and attempt to
start afresh.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180602104853.17140-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>

drm/i915/execlists: Push the tasklet kick after reset to reset_finish

In the unlikely case where we have failed to keep submitting to the GPU,
we end up with the ELSP queue empty but a pending queue of requests.
Here, we skip the per-engine reset as there is no guilty request, but in
doing so we also skip the engine restart leaving ourselves with a
permanently hung engine. A quick way to recover is by moving the tasklet
kick to execlists_reset_finish() (from init_hw). We still emit the error
on hanging, so the error is not lost but we should be able to recover.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604073441.6737-2-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>

drm/i915/selftests: Initialise request to silence a compiler

With an old (4.7.3 on 32bit) gcc, it emits a warning for

In file included from drivers/gpu/drm/i915/i915_request.c:1425:0:
drivers/gpu/drm/i915/selftests/i915_request.c: In function ‘live_nop_request’:
drivers/gpu/drm/i915/selftests/i915_request.c:380:21: error: ‘request’ may be used uninitialized in this function [-Werror=maybe-uninitialized]

Silence it by just setting it to NULL on initialisation.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614124923.18071-1-chris@chris-wilson.co.uk

drm/i915: Turn off g4x DP port in .post_disable()

While Bspec doesn't list a specific sequence for turning off the DP port
on g4x we are getting an underrun if the port is disabled in the
.disable() hook. Looks like the pipe stops when the port stops, and by
that time the plane disable may not have completed yet. Also the plane(s)
seem to end up in some wonky state when this happens as they also signal
another underrun immediately after we turn them back on during the next
enable sequence.

We could add a vblank wait in .disable() to avoid wedging the planes,
but I assume we're still tripping up the pipe in some way. So it seems
better to me to just follow the ILK+ sequence and turn off the DP port
in .post_disable() instead. This sequence doesn't seem to suffer from
this problem. Could be it was always the intended sequence for DP and
the gen4 bspec was just never updated to include it.

Originally we used the bad sequence even on ilk+, but I changed that
in commit 08aff3fe26ae ("drm/i915: Move DP port disable to post_disable
for pch platforms") as it was causing issues on those platforms as well.
I left out g4x then only because I didn't have the hardware to test it.
Now that I do it's fairly clear that the ilk+ sequence is also the
right choice for g4x.

v2: Fix whitespace fail (Jani)
Mention the ilk+ commit (Jani)

Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Disallow interlaced modes on g4x DP outputs

Looks like interlaced DP output doesn't work on g4x either. Not all
that surprising considering we already established that interlaced
DP output is busted on VLV/CHV.

Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-1-ville.syrjala@linux.intel.com

drm/i915: Fix PIPESTAT irq ack on i965/g4x

On i965/g4x IIR is edge triggered. So in order for IIR to notice that
there is still a pending interrupt we have to force and edge in ISR.
For the ISR/IIR pipe event bits we can do that by temporarily
clearing all the PIPESTAT enable bits when we ack the status bits.
This will force the ISR pipe event bit low, and it can then go back
high when we restore the PIPESTAT enable bits.

This avoids the following race:
1. stat = read(PIPESTAT)
2. an enabled PIPESTAT status bit goes high
3. write(PIPESTAT, enable|stat);
4. write(IIR, PIPE_EVENT)

The end result is IIR==0 and ISR!=0. This can lead to nasty
vblank wait/flip_done timeouts if another interrupt source
doesn't trick us into looking at the PIPESTAT status bits despite
the IIR PIPE_EVENT bit being low.

Before i965 IIR was level triggered so this problem can't actually
happen there. And curiously VLV/CHV went back to the level triggered
scheme as well. But for simplicity we'll use the same i965/g4x
compatible code for all platforms.

Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106033
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105225
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106030
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611200258.27121-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/ddi: Removed unused var from hsw_write_infoframe()

Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613170710.15080-6-imre.deak@intel.com

drm/i915/ddi: Set HDMI infoframes with pipe clocks enabled

On ICL for setting the HDMI infoframe the pipe clock needs to be
enabled, otherwise accessing the VIDEO_DIP_CTL register will hang the
machine.

Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613170710.15080-5-imre.deak@intel.com

drm/i915/ddi: Check transcoder instead of port when setting HDMI infoframe

The only requirement by BSpec for setting the HDMI infoframes is on DDI
platforms to do that before enabling the HDMI transcoder function, see
VIDEO_DIP_CTL bit 16. Accordingly check for the transcoder function
disabled state instead of the port's disabled state on DDI platforms.
This is needed by the next patch as it will set the infoframe during
crtc disabling where the port is still enabled.

Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613170710.15080-4-imre.deak@intel.com

drm/i915/ddi: Push pipe clock enabling to encoders

On ICL the pipe clock needs to be enabled before setting the HDMI
infoframe, but these steps are in the reverse order atm. Move the pipe
clock enabling to the encoders, so reordering of the two steps can be
done in a clean way.

No functional change.

v2:
- Rebased on drm-tip.

Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613172746.18525-1-imre.deak@intel.com

drm/i915/ddi: s/crtc->config/old_crtc_state in haswell_crtc_disable()

crtc->config points to the old crtc state at the point
display.crtc_disable() is called, so use the more descriptive pointer
instead.

v2:
- Convert one remaining instance of the ptr in the function. (Ville)

Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613170710.15080-2-imre.deak@intel.com

drm/i915/psr: Kill delays when activating psr back.

The immediate enabling was actually not an issue for the
HW perspective for core platforms that have HW tracking.
HW will wait few identical idle frames before transitioning
to actual psr active anyways.

Now that we removed VLV/CHV out of the picture completely
we can safely remove any delays.

Note that this patch also remove the delayed activation
on HSW and BDW introduced by commit 'd0ac896a477d
("drm/i915: Delay first PSR activation.")'. This was
introduced to fix a blank screen on VLV/CHV and also
masked some frozen screens on other core platforms.
Probably the same that we are now properly hunting and fixing.

v2:(DK): Remove unnecessary WARN_ONs and make some other
         VLV | CHV more readable.
v3: Do it regardless the timer rework.
v4: (DK/CI): Add VLV || CHV check on cancel work at psr_disable.
v5: Kill remaining items and fully rework activation functions.
v6: Rebase on top of VLV/CHV clean-up and keep the reactivation
    on a regular non-delayed work to avoid extra delays on exit
    calls and allow us to add few more safety checks before
    real activation.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613192600.3955-1-rodrigo.vivi@intel.com

drm/i915/gtt: Only keep gen6 page directories pinned while active

In order to be able to evict the gen6 ppgtt, we have to unpin it at some
point. We can simply use our context activity tracking to know when the
ppgtt is no longer in use by hardware, and so only keep it pinned while
being used a request.

For the kernel_context (and thus aliasing_ppgtt), it remains pinned at
all times, as the kernel_context itself is pinned at all times.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614094103.18025-5-chris@chris-wilson.co.uk

drm/i915: Show CCID in engine dumps

For debugging context issues, knowing what context the GPU is
loading/using is helpful.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614094103.18025-4-chris@chris-wilson.co.uk

drm/i915: Make the hexdump row offset visually distinct

Currently we use %08x for the row offset, and %08x for the binary
contents of the buffer. This makes it very easily to confuse the two, so
switch to using [%04x] for the start-of-row offset.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614094103.18025-3-chris@chris-wilson.co.uk

drm/i915: Dump the ringbuffer of the active request for debugging

Sometimes we need to see what instructions we emitted for a request to
try and gather a glimmer of insight into what the GPU is doing when it
stops responding.

v2: Move ring dumping into its own routine

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614122150.17552-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915/dsm: remove unnecessary dsm priv structure

Pass a local acpi_handle around instead of having a static dsm priv
structure. If we need it later, we can always move it to dev_priv, and
the change at hand will make that easier as well.

Care is taken to preserve old behaviour, particularly using the last
non-NULL acpi handle, whether it makes sense or not.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614104709.2808-1-jani.nikula@intel.com

drm/i915: Move GEM sanitize from resume_early to resume

This should be a no-op in terms of our control flow, we move the
sanitization (GPU reset) from the bottom of the early resume phase to
the top of the next. However, following hibernation debug, the power
code skips the early resume phase, but as we are about to completely
restore the GTT mappings, we first need to stop the GPU using them i.e.
perform a GPU reset (i915_gem_sanitize()).

Testcase: igt/gem_exec_suspend/basic-S4-devices
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614094103.18025-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915/opregion: move acpi notifier to dev_priv

Get rid of the silly static variable.

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613113927.30033-1-jani.nikula@intel.com

drm/i915/perf: make oa format tables const

No reason not to be const.

Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613114929.14541-1-jani.nikula@intel.com

drm/i915: Make closing request flush mandatory

For symmetry, simplicity and ensuring the request is always truly idle
upon its completion, always emit the closing flush prior to emitting the
request breadcrumb. Previously, we would only emit the flush if we had
started a user batch, but this just leaves all the other paths open to
speculation (do they affect the GPU caches or not?) With mm switching, a
key requirement is that the GPU is flushed and invalidated before hand,
so for absolute safety, we want that closing flush be mandatory.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612105135.4459-1-chris@chris-wilson.co.uk

drm/i915: Allow DBLSCAN user modes with eDP/LVDS/DSI

When encountering a connector with the scaling mode property both
intel and modesetting ddxs sometimes add tons of DBLSCAN modes
to the output's mode list. The idea presumably being that since the
output will be going through the panel fitter anyway we can pretend
to use any kind of mode.

Sadly that means we can't reject user modes with the DBLSCAN flag
until we know whether we're going to be using the panel's native
mode or the user mode directly. Doing otherwise means X clients using
xf86vidmode/xrandr will get a protocol error (and often self
terminate as a result) when the kernel refuses to use the requested
mode with the DBLSCAN flag.

To undo the regression we'll move the DBLSCAN checks into the
connector->mode_valid() and encoder->compute_config() hooks.

Cc: stable@vger.kernel.org
Cc: Vito Caputo <vcaputo@pengaru.com>
Reported-by: Vito Caputo <vcaputo@pengaru.com>
Fixes: e995ca0b8139 ("drm/i915: Provide a device level .mode_valid() hook")
References: https://lkml.org/lkml/2018/5/21/715
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180524125403.23445-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106804
Tested-by: Arkadiusz Miskiewicz <arekm@maven.pl>

drm/i915: Enable KVMGT for BXT.

Enable KVMGT for BXT.
is_supported_device() acting as the gatekeeper of GVT-g init.
If all supported platforms share the same configurations for some
specific feature, platform check will rely on this check only.

Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Add mmio handler for for BXT.

Leverage most SKL/KBL mmio init info and add different mmio to
BXT specific function init_bxt_mmio_info().

Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Enable dma_buf support for BXT.

Handle dma_buf on BXT as SKL and KBL.

Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Enable virtual display support for BXT.

Virtual monitor on BXT start from port B.
Unlike SKL/KBL, digital display port connectivity is detected via
GEN8_DE_PORT_ISR so emulate monitor state change by setting it.

Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Enable force wake support for BXT.

BXT forcewake is handled in the same way as SKL/KBL.

v2: Add missing inhibit_context restore for BXT.

Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Enable cmd_parser support for BXT.

Handle BXT cmd_parser as SKL/KBL.

v2: All supported platforms share the same routines.
Remove the platform check by now and let is_supported_device()
be the gate keeper.

Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Enable mmio context init and switch for BXT.

Handle pending tlb flush, mocs/mmio switch and context as KBL.

Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Enable irq initialization for BXT.

Initialize BXT irq handler as SKL/KBL.

v2: All supported platforms share the same irq ops and map.
Remove the platform check by now and let is_supported_device()
be the gate keeper.

Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Enable gtt initialization for BXT.

Initialize BXT gtt as SKL/KBL.

v2: All supported platforms share the same gtt ops.
Remove the platform check by now and let is_supported_device()
be the gate keeper.

Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Enable device info initialization for BXT.

Initialize BXT device info as SKL/KBL.

v2: All supported platforms share the same device configuration.
Remove the platform check by now and let is_supported_device()
be the gate keeper.

Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Add MEDIA_POOL_STATE for BXT.

As referred in PRM for Broxton Graphics on 01.org

Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Add D_BXT device type define for BXT.

Broxton belongs to GEN9 family so add to SKL and GEN9 plus.

Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/icl: DP_AUX_E is valid on ICL+

Add support for DP_AUX_E. Here we also introduce the bits for the AUX
power well E, however ICL power well support is still not enabled yet,
so the power well is not used.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612002512.29783-2-paulo.r.zanoni@intel.com

drm/i915/icl: fix gmbus gpio pin mapping

ICP has GPIO pin 1/2 mapped to combo-phy ports & GPIO pins 9/10/11/12
mapped to tc ports[1-4].
This patch defines GPIOCTL registers for GPIO pins 9-12 & uses them in GPIO
pin mapping table.

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612002512.29783-1-paulo.r.zanoni@intel.com

drm/i915/icl: Add DDI HDMI level selection for ICL

This patch adds a proper HDMI DDI entry level for vswing
programming sequences on ICL.

Spec doesn't specify any default for HDMI tables,
so let's pick the last entry as the default for now
to stay consistent with older platform like CNL.

Cc: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180522002558.29262-8-paulo.r.zanoni@intel.com

drm/i915/gtt: Make gen6 page directories evictable

Currently all page directories are bound at creation using an
unevictable node in the GGTT. This severely limits us as we cannot
remove any inactive ppgtt for new contexts, or under aperture pressure.
To fix this we need to make the page directory into a first class and
unbindable vma. Hence, the creation of a custom vma to wrap the page
directory as opposed to a GEM object.

In this patch, we leave the page directories pinned upon creation.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612120446.13901-1-chris@chris-wilson.co.uk

drm/i915/guc: Add support for define guc_log_size in megabytes.

At this moment we can define GuC logs sizes only using pages.
But GuC also allows use for this values expressed in megabytes.
Lets add support for define guc_log_size in megabytes when we
debug of GuC.

v2:
- change buffers size to more friendly (Michał Wajdeczko)
- merge statements in guc_ctl_log_params_flags() (Michał Wajdeczko)
v3:
- fix ifdef (rename DRM_I915_DEBUG_GUC to CONFIG_DRM_I915_DEBUG_GUC)
(Michał Wajdeczko)
- use SZ_* macros to define buffers sizes (Michał Wajdeczko)

Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180605151330.9954-2-piotr.piorkowski@intel.com

drm/i915/guc: Move defines with size of GuC logs to intel_guc_log.h

At this moment, we have defined GuC logs sizes in intel_guc_fwif.h, but
as these values are related directly to the GuC logs, and not to API of
GuC parameters, we should move these defines to intel_guc_log.h.

v2:
- change buffers size to more friendly (Michał Wajdeczko)
- remove GUC_LOG_SIZE define (Michał Wajdeczko)
v3:
- use SZ_* macros to define buffers sizes (Michał Wajdeczko)

Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180605151330.9954-1-piotr.piorkowski@intel.com

drm/i915/guc: Refactoring preparation of the GUC_CTL_CTXINFO parameter

At the moment, the preparation of GUC_CTL_CTXINFO is disordered.
Lets move all GUC_CTL_CTXINFO related operations to one place.

v2:
- move 'ctxnum' and 'base' declarations to USES_GUC_SUBMISSION case
(Michał Wajdeczko)

Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604141947.8299-5-piotr.piorkowski@intel.com

drm/i915/guc: Refactoring preparation of the GUC_CTL_LOG_PARAMS parameter

At the moment, the preparation of GUC_CTL_LOG_PARAMS is disordered.
Additionally, in struct intel_guc_log we have an unnecessary field
'flags' which we use only to assign value to GuC parameter.
Lets move all GUC_CTL_LOG_PARAMS related operations to one place,
and lets remove field 'flags' from struct intel_guc_log.

Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604141947.8299-4-piotr.piorkowski@intel.com

drm/i915/guc: Refactoring preparation of the GUC_CTL_FEATURE parameter

At the moment, the preparation of GUC_CTL_FEATURE is disordered.
Lets move all GUC_CTL_FEATURE related operations to one place.

Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604141947.8299-3-piotr.piorkowski@intel.com

drm/i915/guc: Refactoring preparation of the GUC_CTL_DEBUG parameter

At the moment, the preparation of GUC_CTL_DEBUG is disordered.
Lets move all GUC_CTL_DEBUG related operations to one place.

v2:
- move 'ads' declaration to USES_GUC_SUBMISSION case (Michał Wajdeczko)

Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604141947.8299-2-piotr.piorkowski@intel.com

drm/i915/guc: Don't store runtime GuC log level in modparam

Currently we are using modparam as placeholder for GuC log level.
Stop doing this and keep runtime GuC level in intel_guc_log struct.

v2:
- rename functions intel_guc_log_level_[get|set] to
intel_guc_log_[get|set]_level (Michał Wajdeczko)
- remove GEM_BUG_ON from intel_guc_log_get_level() (Michał Wajdeczko)

Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604141947.8299-1-piotr.piorkowski@intel.com