OSDN Git Service
Daniel Vetter [Wed, 21 May 2014 15:37:52 +0000 (17:37 +0200)]
drm/i915: move bsd dispatch index somewhere better
Adding stuff at the bottom is really no how this should be done, since
that's the place for ums/dri dungeons.
This was added in
commit
a8ebba75b358f9c912cbcba0c14a2072e7280b2f
Author: Zhao Yakui <yakui.zhao@intel.com>
Date: Thu Apr 17 10:37:40 2014 +0800
drm/i915: Use the coarse ping-pong mechanism based on drm fd to dispatch the BSD command on BDW GT3
Also add a note to prevent this from happening again - people really
should be less lazy and take more time to look for a good home of
their new driver-global state.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 16 May 2014 16:40:25 +0000 (19:40 +0300)]
drm/i915: Shuffle fifo underrun disable/enable points for gmch platforms
Gen2 reports FIFO underruns whenever no planes are enabled on the pipe.
So in order to avoid false positives we must enable the FIFO underrun
reporting only when at least one plane is enabled on the pipe. For
now just move the underrun reporting enable/disable points to the
other side of the plane enable/disable point. That doesn't cover cases
when we turn off all the planes for the pipe but leave the pipe running
on purpose, but it's better than the current situation.
On gen4+ we can actually move the underrun reporting enable/disable to
the opposite ends of the crtc enable/disable hooks. I suppose in theory
we could leave the underrun reporting enabled all the time, except on
VLV where PIPESTAT stops working when the display power well is down.
If we ever get around to unifying the PIPESTAT irq handling for all
gmch platforms, we should still follow the VLV route for other platforms.
It would also micro-optimize the irq handler a bit since we could then
skip the PIPESTAT reads for all disabled pipes.
Gen3 is still a mystery, but for now I'm going to assume it behaves
like gen4+.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 16 May 2014 16:40:24 +0000 (19:40 +0300)]
drm/i915: Simplify the uncleared FIFO underrun detection
Checking whether the error interrupt was enabled or not isn't really
necessary when we check for uncleared FIFO underruns. If it was enabled
we'll race with the interrupt handler a bit, but that seems OK as we
still claim the interrupt.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 16 May 2014 16:40:22 +0000 (19:40 +0300)]
drm/i915: Check for FIFO underruns at the end of modeset on gmch
FIFO underruns don't generate interrupts on gmch platforms, so
if we want to know whether a modeset triggered FIFO underruns we
need to explicitly check for them.
As a modeset on one pipe could cause underruns on other pipes,
check for underruns on all pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
[danvet: Fix up merge error, kudos to Ville for noticing it.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 16 May 2014 16:40:21 +0000 (19:40 +0300)]
drm/i915: Check for FIFO underuns when disabling reporting on gmch platforms
FIFO underruns don't generate an interrupt on gmch platforms, so we
should check whether there were any that we failed to notice when
we're disabling FIFO underrun reporting.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 21 May 2014 13:11:33 +0000 (15:11 +0200)]
drm/irq: Coding style fix
Noticed by Thierry Reding in his review, but I've merged the drm
vblank rework topic branch a bit too quickly. So separate fixup.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 25 Apr 2014 17:14:32 +0000 (20:14 +0300)]
drm/i915: Provide DPIO diagrams as docboox tables
The ascii art version of the DPIO diagram gets mangled by docbook, so
we can't use it there. Insted provide another version built using
<table>.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 25 Apr 2014 17:14:31 +0000 (20:14 +0300)]
drm/i915: Add a brief description of the VLV display PHY internals
Document the internal structure of the VLV display PHY a bit to help
people understand how the different register blocks relate to each
other.
v2: Add a bit more text
Make it a DOC: comment, but leave the ascii art out since
it would get mangled
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Wed, 21 May 2014 16:01:06 +0000 (19:01 +0300)]
drm/i915: Add null state batch to active list
for proper refcounting to take place as we use
i915_add_request() for it.
i915_add_request() also takes the context for the request
from ring->last_context so move the null state batch
submission after the ring context has been set.
v2: we need to check for correct ring now (Ville Syrjälä)
v3: no need to expose i915_gem_move_object_to_active (Chris Wilson)
v4: cargoculted vma/active/inactive error handling removed (Chris Wilson)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 20 May 2014 14:20:05 +0000 (17:20 +0300)]
drm/i915: Re-enable vblank irqs for already active pipes
If a pipe is already active when we init/resume there might not be a
full modeset afterwards so drm_vblank_on() may not get called. In such
a case if someone is holding a vblank reference across a suspend/resume
cycle drm_vblank_get() called after resuming won't re-enable the vblank
interrupts.
So in order to make sure vblank interrupts get re-enabled post-resume,
call drm_vblank_on() in intel_sanitize_crtc() if the crtc is already
active.
v2: Also drm_vblank_off() if the pipe got disabled magically
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Testecase: igt/kms_flip/vblank-vs-suspend
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 21 May 2014 09:45:40 +0000 (11:45 +0200)]
Merge branch 'topic/drm-vblank-rework' into drm-intel-next-queued
Pull in the drm vblank rework from Ville and me. drm core parts acked
by Dave Airlie
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Just a bit of fun around the placement of drm_vblank_on. This merge
resolution has been tested in drm-intel-nightly for a while already.
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 14 May 2014 13:40:34 +0000 (15:40 +0200)]
drm/i915: Accurately initialize fifo underrun state on gmch platforms
We don't have hardware based disable bits on gmch platforms, so need
to block spurious underrun reports in software. Which means that we
_must_ start out with fifo underrun reporting disabled everywhere.
This is in big contrast to ilk/hsw/cpt where there's only _one_
disable bit for all platforms and hence we must allow underrun
reporting on disabled pipes. Otherwise nothing really works,
especially the CRC support since that's key'ed off the same irq
disable bit.
This allows us to ditch the fifo underrun reporting hack from the vlv
runtime pm code and unexport the internal function from i915_irq.c
again. Yay!
v2: Keep the display irq disabling, spotted by Imre.
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 14 May 2014 13:26:49 +0000 (15:26 +0200)]
drm/i915: rip our vblank reset hacks for runtime PM
Now that we unconditionally dtrt when disabling/enabling crtcs we
don't need any hacks any longer to keep the vblank logic sane when
all the registers go poof. So let's rip it all out.
This essentially undoes
commit
9dbd8febb4dbc9199fcf340b882eb930e36b65b6
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Tue Jul 23 10:48:11 2013 -0300
drm/i915: update last_vblank when disabling the power well
Apparently igt/kms_flip is already powerful enough to exercise this
properly, yay! See the reference regression report for details.
v2: Update testcase name
References: https://bugs.freedesktop.org/show_bug.cgi?id=66808
Testcase: igt/kms_flip/vblank-vs-*-rpm
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 15 May 2014 13:33:46 +0000 (15:33 +0200)]
drm/i915: Use new kms-native vblank functions
Only the low-level irq handling functions still use integer crtc
indices with this. But fixing that will require a lot more sugery
and some good ideas for backwards compat with old ums userspace.
Both in drivers and in the drm core.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 15 May 2014 13:32:12 +0000 (15:32 +0200)]
drm/irq: Add kms-native crtc interface functions
We need to start somewhere ... With this the only places left in i915
where we use pipe integers is in the interrupt handling code. And
there it actually makes some amount of sense.
v2:
- Polish kerneldoc a bit (Thierry).
- Drop "dev" parameter since it's unecessary.
- Split out i915 changes (Thierry).
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 8 May 2014 14:41:51 +0000 (16:41 +0200)]
drm/irq: kerneldoc polish
- Integrate into the drm DocBook
- Disable kerneldoc for functions not exported to drivers.
- Properly document the new drm_vblank_on|off and add cautious
comments explaining when drm_vblank_pre|post_modesets shouldn't be
used.
- General polish and OCD.
v2: Polish as suggested by Thierry.
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 8 May 2014 13:39:19 +0000 (15:39 +0200)]
drm/doc: Discourage usage of MODESET_CTL ioctl
Leftover from the old days of ums and should be used any longer. Since
commit
29935554b384b1b3a7377d6f0b03b21d18a61683
Author: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Date: Wed May 30 00:58:09 2012 +0200
drm: Disallow DRM_IOCTL_MODESET_CTL for KMS drivers
it is a complete no-Op for kms drivers.
v2: Fix up mangled sentence spotted by Michel.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Michel Dänzer <michel@daenzer.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 11 Mar 2014 16:09:31 +0000 (17:09 +0100)]
drm/i915: Remove drm_vblank_pre/post_modeset calls
Originally these functions have been for user modesetting drivers to
ensure vblank processing doesn't fall over completely around modeset
changes. This has been carried over ever since then.
Now that Ville cleaned our vblank handling with an explicit
drm_vblank_off/on braket when disabling/enabling crtcs. So this seems
to be unnecessary now. The most important side effect was that due to
the delayed vblank disabling we have been pretty much guaranteed to
receive a vblank interrupt soonish after a crtc was enabled.
Note that our vblank handling across modeset is still fairly decent
fubar - we don't actually handle vblank counter all to well.
drm_update_vblank_count will make sure that the frame counter always
rolls forward, but userspace isn't really all to ready to cope with
the big jumps this causes.
This isn't a big mostly because the hardware retains the frame
counter. But with runtime pm and also across suspend/resume we fall
over.
Fixing this is a lot more involved and also needs som i-g-ts. So
material for another patch series.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Apr 2014 18:41:38 +0000 (21:41 +0300)]
drm/i915: Move buffer pinning and ring selection to intel_crtc_page_flip()
All of the .queue_flip() callbacks duplicate the same code to pin the
buffers and calculate the gtt_offset. Move that code to
intel_crtc_page_flip(). In order to do that we must also move the ring
selection logic there.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 25 Apr 2014 10:30:12 +0000 (13:30 +0300)]
drm/i915: Drop the excessive vblank waits from modeset codepaths
Now that we've plugged the mmio vs. ring flip race, we shouldn't need
these vblank waits in the modeset codepaths anymore. So get rid of
them.
v2: gen2 needs to wait for planes to turn off before disabling pipe
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Apr 2014 18:41:35 +0000 (21:41 +0300)]
drm/i915: Wait for vblank in hsw_enable_ips()
Now that the vblank wait is gone from intel_enable_primary_plane(),
hsw_enable_ips() needs to do the vblank wait itself.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 15 Apr 2014 18:41:34 +0000 (21:41 +0300)]
drm/i915: Fix mmio vs. CS flip race on ILK+
Starting from ILK, mmio flips also cause a flip done interrupt to be
signalled. This means if we first do a set_base and follow it
immediately with the CS flip, we might mistake the flip done interrupt
caused by the set_base as the flip done interrupt caused by the CS
flip.
The hardware has a flip counter which increments every time a mmio or
CS flip is issued. It basically counts the number of DSPSURF register
writes. This means we can sample the counter before we put the CS
flip into the ring, and then when we get a flip done interrupt we can
check whether the CS flip has actually performed the surface address
update, or if the interrupt was caused by a previous but yet
unfinished mmio flip.
Even with the flip counter we still have a race condition of the CS flip
base address update happens after the mmio flip done interrupt was
raised but not yet processed by the driver. When the interrupt is
eventually processed, the flip counter will already indicate that the
CS flip has been executed, but it would not actually complete until the
next start of vblank. We can use the DSPSURFLIVE register to check
whether the hardware is actually scanning out of the buffer we expect,
or if we managed hit this race window.
This covers all the cases where the CS flip actually changes the base
address. If the base address remains unchanged, we might still complete
the CS flip before it has actually completed. But since the address
didn't change anyway, the premature flip completion can't result in
userspace overwriting data that's still being scanned out.
CTG already has the flip counter and DSPSURFLIVE registers, and
although the flip done interrupt is still limited to CS flips alone,
the code now also checks the flip counter on CTG as well.
v2: s/dspsurf/gtt_offset/ (Chris)
Testcase: igt/kms_mmio_vs_cs_flip/setcrtc_vs_cs_flip
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73027
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add g4x_ prefix to flip_count_after_eq.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes [Tue, 20 May 2014 22:25:33 +0000 (15:25 -0700)]
drm/i915: drop encoder hot_plug calls at resume
We really just want to go detect displays again and fire off a hotplug
event if things have changed, not go through full hotplug processing.
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 20 May 2014 20:46:50 +0000 (22:46 +0200)]
drm/i915: Drop now misleading DDI comment from dp_link_down
Since
commit
2e82a7203182d0883d0f9450d40ad6e1c6578ad9
Author: Imre Deak <imre.deak@intel.com>
Date: Fri Jan 17 15:46:43 2014 +0200
drm/i915: don't disable DP port after a failed link training
and
commit
5d6a1116c6475404e6505b708320f9579ae19acd
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Jan 16 18:35:57 2014 +0200
drm/i915: don't disable the DP port if the link is lost
we no longer call intel_dp_link_down from generic DP code, but only
from the !HAS_DDI dp encoder functions. hsw/bdw have their own encoder
disabling callback in intel_ddi.c.
Hence the early return is no longer needed and the big comment just
confusing, so let's rip it out. To ensure what we don't accidentally
use this again on ddi encoders add a WARN_ON instead.
Spotted while reading through intel_dp.c
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 19 Feb 2014 19:29:49 +0000 (21:29 +0200)]
drm: Add drm_vblank_on()
drm_vblank_off() will turn off vblank interrupts, but as long as the
refcount is elevated drm_vblank_get() will not re-enable them. This
is a problem is someone is holding a vblank reference while a modeset is
happening, and the driver requires vblank interrupt to work during that
time.
Add drm_vblank_on() as a counterpart to drm_vblank_off() which will
re-enabled vblank interrupts if the refcount is already elevated. This
will allow drivers to choose the specific places in the modeset sequence
at which vblank interrupts get disabled and enabled.
Testcase: igt/kms_flip/*-vs-suspend
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add Testcase tag for the igt I've written.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 6 Mar 2014 15:27:39 +0000 (17:27 +0200)]
drm: Make blocking vblank wait return when the vblank interrupts get disabled
If there's a blocking vblank wait in progress while the vblank interrupt
gets disabled, the current code will just let the vblank wait time out.
Instead make it return immediately when vblank interrupts get disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 19 Feb 2014 17:36:08 +0000 (19:36 +0200)]
drm: Make the vblank disable timer per-crtc
Currently there's one per-device vblank disable timer, and it gets
reset wheneven the vblank refcount for any crtc drops to zero. That
means that one crtc could accidentally be keeping the vblank interrupts
for other crtcs enabled even if there are no users for them. Make the
disable timer per-crtc to avoid this issue.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Peter Hurley [Wed, 21 Aug 2013 01:51:12 +0000 (21:51 -0400)]
drm: Use correct spinlock flavor in drm_vblank_get()
The irq flags state is already established by the outer
spin_lock_irqsave(); re-disabling irqs is redundant.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Tue, 29 Apr 2014 20:30:48 +0000 (23:30 +0300)]
drm/i915: shuffle panel code
Somehow a few functions have been dropped in the middle of backlight
code. Move them around. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 19 May 2014 16:23:26 +0000 (19:23 +0300)]
drm/i915: Clear GDSR after reset on ILK
Clear the reset domain after a succesful GPU reset on ilk. We already
do that on gen4, so let's try to be a bit more consistent. And if
ether render or media reset fails, we might use the leftover value
in the register to pinpoint the culprit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 19 May 2014 16:23:25 +0000 (19:23 +0300)]
drm/i915: Kill RMW from ILK reset code
All the other bits in the GDSR register are read-only, so we don't have
to preserve them when we perform a GPU reset.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Tue, 20 May 2014 16:47:20 +0000 (19:47 +0300)]
drm/i915: add missing unregister_oom_notifier to the error/unload path
I'm trying to reduce the WARNs during driver reload and this was one of
them. Also while at it remove the redundant condition from before
unregister_shrinker().
v2:
- fix the error path too and move the unregister to its logical place
(Chris)
- remove redundant condition from before unregister_shrinker()
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 25 Apr 2014 17:14:30 +0000 (20:14 +0300)]
drm/i915: Drop /** */ comments from i915_reg.h
The comments in i915_reg.h aren't proper kernel-doc comments, so replace
the magic /** with just /*
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:41 +0000 (13:28 +0300)]
drm/i915/chv: Add a bunch of pre production workarounds
The following workarounds should be needed for pre-production hardware
only:
* WaDisablePwrmtrEvent:chv
* WaSetMaskForGfxBusyness:chv
* WaDisableGunitClockGating:chv
* WaDisableFfDopClockGating:chv
* WaDisableDopClockGating:chv
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:29:04 +0000 (13:29 +0300)]
drm/i915/chv: Use RMW to toggle swing calc init
The spec only tells us to set individual bits here and there. So we use
RMW for most things. Do the same for the swing calc init.
Eventually we should optimize things to just blast the final value in
with group access whenever possible. But to do that someone needs to
take a good look at what's the reset value for each registers, and
possibly if the BIOS manages to frob with some of them. For now
use RMW access always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:29:03 +0000 (13:29 +0300)]
drm/i915/chv: Don't do group access reads from TX lanes either
Like PCS, TX group reads return 0xffffffff. So we need to target each
lane separately if we want to use RMW cycles to update the registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:29:02 +0000 (13:29 +0300)]
drm/i915/chv: Don't use PCS group access reads
All PCS groups access reads return 0xffffffff, so we can't use group
access for RMW cycles. Instead target each spline separately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Fight conflict with misplaced ; .... ARGH!]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 28 Apr 2014 11:15:24 +0000 (14:15 +0300)]
drm/i915/chv: Set soft reset override bit for data lane resets
The bits we've been setting so far only progagate the reset singal to
the data lanes. To actaully force the reset signal we need to set another
override bit.
v2: Fix mispalced ';' (Mika)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:29:00 +0000 (13:29 +0300)]
drm/i915/chv: Reset data lanes in encoder .post_disable() hook
Seems like we shouldn't leave the data lane resert deasserted when
the port if disabled. So propagate the reset the data lanes in
the encoder .post_disable() hook.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:59 +0000 (13:28 +0300)]
drm/i915/chv: Turn off dclkp after the PLL has been disabled
During the enable sequence we first enable the dclkp output to the
display controller, and then enable the PLL. Do the opposite during
the disable sequence.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:58 +0000 (13:28 +0300)]
drm/i915/chv: Move data lane deassert to encoder pre_enable
We need to pick the correct data lanes based on the port not the
pipe, so move the data lane deassert into the encoder .pre_enable()
hook from the chv_enable_pll().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:57 +0000 (13:28 +0300)]
drm/i915/chv: Fix CHV PLL state tracking
Setup the pipe config dpll state correctly for CHV. Also add
a assert_pipe_disabled() to chv_disable_pll(), and program the
DPLL_MD registers in chv_enable_pll().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:56 +0000 (13:28 +0300)]
drm/i915/chv: Register port D encoders and connectors
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:55 +0000 (13:28 +0300)]
drm/i915/chv: Fix PORT_TO_PIPE for CHV
Fix the encoder .get_config hooks to report the correct active pipe for
CHV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:54 +0000 (13:28 +0300)]
drm/i915/chv: Bump num_pipes to 3
CHV has three pipes so let's expose them all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:53 +0000 (13:28 +0300)]
drm/i915/chv: Add cursor pipe offsets
Unsurprisingly the cursor C regiters are also at a weird offset on CHV.
Add more pipe offsets to handle them.
This also gets rid of most of the differences between the i9xx vs. ivb
cursor code. We can unify the remaining code as well, but I'll leave
that for another patch.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:52 +0000 (13:28 +0300)]
drm/i915/chv: Fix gmbus for port D
On CHV the GMBUS port for port D is different from other gmch platforms
which have port D. Fix it up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 28 Apr 2014 11:07:43 +0000 (14:07 +0300)]
drm/i915/chv: Configure crtc_mask correctly for CHV
On CHV pipe C can driver only port D, and pipes A and B can drivbe only
ports B and C. Configure the crtc_mask appropriately to reflect that.
v2: Moar braces (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:50 +0000 (13:28 +0300)]
drm/i915/chv: Make CHV irq handler loop until all interrupts are consumed
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:49 +0000 (13:28 +0300)]
drrm/i915/chv: Use valleyview_pipestat_irq_handler() for CHV
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:48 +0000 (13:28 +0300)]
drm/i915/chv: Clarify VLV/CHV PIPESTAT bits a bit more
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rafael Barbalho [Mon, 28 Apr 2014 11:00:42 +0000 (14:00 +0300)]
drm/i915/chv: Add CHV display support
Add support for the third pipe in cherrview
v2: Don't use spaces for indentation (Jani)
Wrap long lines
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
[vsyrjala: slightly massaged the patch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rafael Barbalho [Wed, 9 Apr 2014 10:28:40 +0000 (13:28 +0300)]
drm/i915/chv: Implement WaDisableSamplerPowerBypass for CHV
Cherryview also needs this WA.
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
[vsyrjala: Looks like it's for pre-prodution hw only]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 28 Apr 2014 11:31:09 +0000 (14:31 +0300)]
drm/i915/chv: Add some workaround notes
We implement the following workarounds:
* WaDisableAsyncFlipPerfMode:chv
* WaProgramMiArbOnOffAroundMiSetContext:chv
v2: Drop WaDisableSemaphoreAndSyncFlipWait note
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:38 +0000 (13:28 +0300)]
drm/i915/chv: Implement WaDisableSDEUnitClockGating:chv
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:37 +0000 (13:28 +0300)]
drm/i915/chv: Implement WaDisableCSUnitClockGating:chv
This workaround is listed for CHV, but not for BDW. However BSpec notes
that on BDW CSunit clock gating is always disabled irrespective of the
relevant bit in the GEN6_UGCTL1 registers. For CHV however, such text
is not present in BSpec, so it seems safer to just set the bit.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:36 +0000 (13:28 +0300)]
drm/i915/chv: Implement WaDisableSemaphoreAndSyncFlipWait:chv
BDW has the same requirement but the w/a database doens't list
this w/a for BDW. Seems to be another one of those "stick a bunch
of known workarounds into this bag and write something on the label"
type of things.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:35 +0000 (13:28 +0300)]
drm/i915/chv: Implement WaVSRefCountFullforceMissDisable:chv and WaDSRefCountFullforceMissDisable:chv
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:34 +0000 (13:28 +0300)]
drm/i915/chv: Implement WaDisableThreadStallDopClockGating:chv
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 9 Apr 2014 10:28:33 +0000 (13:28 +0300)]
drm/i915/chv: Implement WaDisablePartialInstShootdown:chv
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 24 Apr 2014 21:55:14 +0000 (23:55 +0200)]
drm/i915: s/ironlake_/intel_ for the enable_share_dpll function
Besides the fairly useless BUG_ON the logic is completely generic
and cane be used on any platform what wants to reuse the shared
dpll support code.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 24 Apr 2014 21:55:13 +0000 (23:55 +0200)]
drm/i915: Extract intel_prepare_shared_dpll
This is the last piece of code which write state to the hardware in
the ironalake ->crtc_mode_set callback.
I think we could merge this with the pll->enable hook, but otoh the
ordering requirements with the ldvs port are really tricky. Doing the
FP0/1 writes up-front before we even prepare the lvds port (in the
pre_pll_enable hook) like on i9xx seems safest.
With this ilk+ platforms are now ready for runtime PM with DPMS. Since
hsw/bdw also support runtime pm besides snb we need to first make the
haswell code save before we can touch the core code.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 20 May 2014 13:19:19 +0000 (15:19 +0200)]
drm/i915: Only update shared dpll state when needed
Instead of every time it isn't active: We only need to do that when
the pll is currently unused, i.e. when pll->refcount == 0. For
paranoia add a warning for the ibx case where plls have a fixed
mapping and hence should always be unused after the call to
intel_put_shared_dpll.
v2: Simplify control flow and use struct assignment instead of memcpy
as suggested by Damien.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 24 Apr 2014 21:55:11 +0000 (23:55 +0200)]
drm/i915: Extract vlv_prepare_pll
With this all hw writes are also gone from the ->crtc_mode_set hook on
vlv. I wondered whether we should track more of the pll state in the
pipe config, but otoh as long as we don't have shared plls that's not
really useful - the cross-checking of the port clock should be
sufficient.
While at it also de-magic some of the pipe checks, this has been
irking me since a long time.
Whit this vlv is now ready for runtime PM on dpms. If we'd have
runtime PM support in general ...
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 24 Apr 2014 21:55:10 +0000 (23:55 +0200)]
drm/i915: Extract i9xx_set_pll_dividers
These two writes are the very last hw writes from the
->crtc_modeset_callback on pre-gen5 hardware. As usual vlv is a bit
different, so this here is just warm-up.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 24 Apr 2014 21:55:09 +0000 (23:55 +0200)]
drm/i915: Shovel hw setup code out of hsw_crtc_mode_set
Again the same story: This code just transform sw state from the pipe
config into hardware state. And again we can't move the pll code, but
this time around because the state isn't properly tracked in the pipe
config.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 24 Apr 2014 21:55:08 +0000 (23:55 +0200)]
drm/i915: Shovel hw setup code out of ilk_crtc_mode_set
Again this code just transforms sw state from the pipe config into
hardware state, so we can just move it around. Unfortunately again a
few forward declarations since intel_display.c is becoming a bit of a
mess.
Note that both for i9xx and ironlake code the only things remaining in
the ->crtc_mode_set hook is now the clock state computation and
sharing code. That needs to be moved into the compute config stage so
that we can catch impossible configurations earlier.
Also note that some of the DPLL hw setup code is still run from within
->crtc_mode_set, namele the pll->mode_set callback. We need to move
that first before we can do fancy things like enable runtime PM for
dpms off.
v2: Make it compile again after the rebase, bisectability issue
reported by Wu Fengguang.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 24 Apr 2014 21:55:07 +0000 (23:55 +0200)]
drm/i915: Move lowfreq_avail around a bit in ilk/hsw_crtc_mode_set
Now this really should be in the pipe config somewhere, but till now
it isn't. We can at least move it up a bit next to all the other pll
code since intel_dp_set_m_n really doesn't depend upon this.
This is just prep work so that moving all the hw frobbing code from
->crtc_mode_set to ->crtc_enable is clean.
v2: Do the same for haswell while at it, not just for ivb.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 24 Apr 2014 21:55:06 +0000 (23:55 +0200)]
drm/i915: Shovel hw setup code out of i9xx_crtc_mode_set
All these functions simply convert sw state as encoded in the pipe
config or primary framebuffer into hardware state. So we can move them
all into the crtc enable hook. Unfortunately this means a little bit
of duplication between the i9xx and vlv functions, but since we
already have highly refactored code I think this is acceptable.
Also a pile of forward declarations unfortunately.
Note also that the various <platform>_update_pll functions are still
called from within the ->crtc_mode_set hook. Mostly they compute the
clock state for the pipe config, but unfortunately there are some
random register writes interspersed. Those need to be moved out first
before we can enable runtime PM for DPMS.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Tue, 20 May 2014 07:28:43 +0000 (08:28 +0100)]
drm/i915: Implement an oom-notifier for last resort shrinking
Before the process killer is invoked, oom-notifiers are executed for one
last try at recovering pages. We can hook into this callback to be sure
that everything that can be is purged from our page lists, and to give a
summary of how much memory is still pinned by the GPU in the case of an
oom. This should be really valuable for debugging OOM issues.
Note that the last-ditch effort call to shrink_all we've previously
called from our normal shrinker when we could free as much as the vm
demaned is moved into the oom notifier. Since the shrinker accounting
races against bind/unbind operations we might have called shrink_all
prematurely, which this approach with an oom notifier avoids.
References: https://bugs.freedesktop.org/show_bug.cgi?id=72742
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: lu hua <huax.lu@intel.com>
[danvet: Bikeshed logical | into || and pimp commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 19 May 2014 16:23:24 +0000 (19:23 +0300)]
drm/i915: Fix ILK GPU reset domain bits
We're using the reset domains bits for g4x on ilk. But on ilk those bits
actually shifted by one bit. Fix it up so that we use the correct bits.
We were actually always writing 0x2 to the reset domain bits, which
is a reserved value. In practice it looks like the hardware ignores that
value since nothing happens if I write that value when there's a 3D
workload running. Writing the _correct_ render domain value actually
makes the GPU stop.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 19 May 2014 16:23:23 +0000 (19:23 +0300)]
drm/i915: Fix ILK reset wait
We should be waiting for the reset bit to clear, not remain set.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 19 May 2014 16:23:22 +0000 (19:23 +0300)]
drm/i915: Drop bogus comments about display reset
There are comments in the gen4-5 reset functions stating that we can't
reset render and media without also doing a display reset. But that's
exactly what the code does, ie. we don't perform a display reset. Drop
the bogus comments.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Tue, 25 Mar 2014 13:23:06 +0000 (13:23 +0000)]
drm/i915: Invalidate our pages under memory pressure
Try to flush out dirty pages into the swapcache (and from there into the
swapfile) when under memory pressure and forced to drop GEM objects from
memory. In effect, this should just allow us to discard unused pages for
memory reclaim and to start writeback earlier.
v2: Hugh Dickins warned that explicitly starting writeback from
shrink_slab was prone to deadlocks within shmemfs.
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Tue, 25 Mar 2014 13:23:05 +0000 (13:23 +0000)]
drm/i915: Refactor common lock handling between shrinker count/scan
We can share a few lines of tricky lock handling we need to use for both
shrinker routines and in the process fix the return value for count()
when reporting a deadlock.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Tue, 25 Mar 2014 13:23:04 +0000 (13:23 +0000)]
drm/i915: Include bound and active pages in the count of shrinkable objects
When the machine is under a lot of memory pressure and being stressed by
multiple GPU threads, we quite often report fewer than shrinker->batch
(i.e. SHRINK_BATCH) pages to be freed. This causes the shrink_control to
skip calling into i915.ko to release pages, despite the GPU holding onto
most of the physical pages in its active lists.
References: https://bugs.freedesktop.org/show_bug.cgi?id=72742
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Tue, 25 Mar 2014 13:23:03 +0000 (13:23 +0000)]
drm/i915: Translate ENOSPC from shmem_get_page() to ENOMEM
shmemfs first checks if there is enough memory to allocate the page
and reports ENOSPC should there be insufficient, along with
the usual ENOMEM for a genuine allocation failure.
We use ENOSPC in our driver to mean that we have run out of aperture
space and so want to translate the error from shmemfs back to
our usual understanding of ENOMEM. None of the the other GEM users
appear to distinguish between ENOMEM and ENOSPC in their error handling,
hence it is easiest to do the fixup in i915.ko
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shashank Sharma [Mon, 19 May 2014 15:24:03 +0000 (20:54 +0530)]
drm/i915: Add MIPI mmio reg base
This patch adds a mmio base address variable for DSI display,
to make the DSI code generic, so that, if required, the same code
can be re-used for future platforms with different mmio base.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Mon, 19 May 2014 14:09:35 +0000 (16:09 +0200)]
drm/i915: Don't die in wait_for_pending_flips
We can apperently miss them, but breaking the entire driver hampers
testing. So bail out after one minute, our customerary "this is a lost
cause" timeout.
References: https://bugs.freedesktop.org/show_bug.cgi?id=78383
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Mon, 19 May 2014 08:41:18 +0000 (11:41 +0300)]
drm/i915: vlv/chv: fix DSI sideband register accessing
So far we used the wrong opcodes to access the DSI registers, so the
register writes during DSI programming didn't actually succeed and left
the registers unchanged. This wasn't a problem for the initial modeset,
where the BIOS-programmed values happened to work, but after resuming
from s0ix these registers are reset and failing to program them results
in a blank screen.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Mon, 19 May 2014 08:41:17 +0000 (11:41 +0300)]
drm/i915: rename IOSF sideband opcodes according to the spec
These opcodes are not specific for an endpoint, but are the same for all
endpoints. So rename them accordingly, using the name the VLV2 sideband
HAS uses. Also move the macros to the .c file, since they aren't used
anywhere else.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Robin Schroer [Sun, 18 May 2014 00:24:50 +0000 (02:24 +0200)]
drivers/gpu/drm/i915/intel_display: coding style fixes
Fixed several switch statements, curly braces, dereference operators
and keywords.
Signed-off-by: Robin Schroer <sulamiification@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 24 Apr 2014 21:55:05 +0000 (23:55 +0200)]
drm/i915: Move fb pinning into __intel_set_mode
Our two ->crtc_mode_set callbacks really don't care whether the fb is
pinned and set up already or not - all the state computation and
handling which originally looked at the framebuffer is already using
the indirection through the pipe configuration.
Eventually we want to move this up a bit more, but as long as the crtc
mode_set callback still exists (and as long as we don't need to pin an
entire pile of planes due to atomic modesets) there's not much point
in it. So I'll let this be for now.
v2: Don't forget about haswell ...
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 24 Apr 2014 21:55:04 +0000 (23:55 +0200)]
drm/i915: Inline set_base into crtc_mode_set
A lot of the code in set_base is uncessary when the crtc is off, so we
can get rid of it all. Also, we don't need to call the fbc/psr update
functions since the crtc enable/disable hooks do that already.
The only things we really need are:
- Pin the new framebuffer and potentially unpin the old framebuffer
(if the crtc has been on and we only change the configuration).
- Update the plane registers.
The first step will move out of platform code with the very next
patch.
v2: Don't forget about haswell ...
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 24 Apr 2014 21:55:03 +0000 (23:55 +0200)]
drm/i915: Sprinkle intel_edp_psr_update over crtc_enable/disable
My plan here is to split up set_base into a prepare step, which does
the pinning, and a commit stage, which updates the hw state. Eventually
we should be able to move the prepare step at the beginning of any
atomic update. For now I only want to move the commit step into the
crtc_enable callbacks.
As a prep step sprinkle intel_edp_psr_update all over the place so
that we don't have to concern ourselves with that in the commit step.
v2: Rebase on top of Ville's enable/disable functions for all planes.
v3: Rebase more.
Reviewed-by: Akash Goel <akash.goel@intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 24 Apr 2014 21:55:02 +0000 (23:55 +0200)]
drm/i915: More cargo-culted locking for intel_update_fbc
Just for consistency, this patch won't fix anything really.
v2: Rebase over all the recent plane enabling shuffling.
Reviewed-by: Akash Goel <akash.goel@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 24 Apr 2014 21:55:01 +0000 (23:55 +0200)]
drm/i915: Make ->update_primary_plane infallible
Way back we've used this to reject framebuffers with unsupported
pixel formats. But since the modesetting reorg with the compute
config stage we reject those much earlier and just BUG() in this
callback. So switch to a void return type.
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Thu, 15 May 2014 09:41:42 +0000 (10:41 +0100)]
drm/i915: Retire requests before creating a new one
More fallout from
commit
c8725f3dc0911d4354315a65150aecd8b7d0d74a
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Mar 17 12:21:55 2014 +0000
drm/i915: Do not call retire_requests from wait_for_rendering
is that we can completely fill all of memory using small objects, such
that we exhaust the filp space, and spend all of our time evicting
objects from the aperture. As such, we never fill the ring, and never
trigger the last resort flushing in
commit
1cf0ba14740d96fbf6f58a201f000a34b74f4725
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon May 5 09:07:33 2014 +0100
drm/i915: Flush request queue when waiting for ring space
and so all the requests are left active and the objects keep that last
active reference. Eventually the system comes to a halt as it runs out
of memory.
The impact is mainly limited to test cases as regular userspace will
trigger retirement by manually checking whether an object is active.
Testcase: igt/gem_lut_handle
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78724
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Guo Jinxian <jinxianx.guo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Airlie [Mon, 19 May 2014 01:15:08 +0000 (11:15 +1000)]
Merge branch 'ast-updates' of ssh://people.freedesktop.org/~/linux into drm-next
Pull in latest updates to AST driver.
* 'ast-updates' of ssh://people.freedesktop.org/~/linux:
drm/ast: initial DP501 support (v0.2)
drm/ast: rename the mindwm/moutdwm and deinline them
drm/ast: resync the dram post code with upstream
drm/ast: add AST 2400 support.
drm/ast: add widescreen + rb modes from X.org driver (v2)
Dave Airlie [Fri, 28 Mar 2014 01:05:12 +0000 (11:05 +1000)]
drm/ast: initial DP501 support (v0.2)
This is the initial attempt at porting the DP501 code from the userspace
driver,
the firmware file is in
http://people.freedesktop.org/~airlied/ast_dp501_fw.bin
this should really be exposed as another encoder/connector that is cloneable
v0.2:
init 3rd tx properly,
add scratch reduction of VRAM size
backup firmware properly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 28 Mar 2014 00:22:41 +0000 (10:22 +1000)]
drm/ast: rename the mindwm/moutdwm and deinline them
we'll need these elsewhere for dp501.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 17 Jan 2014 01:36:14 +0000 (11:36 +1000)]
drm/ast: resync the dram post code with upstream
This resyncs the dram post code with the upstream X.org driver
where ast have improved the code for setting up the dram chips.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 27 Mar 2014 23:18:45 +0000 (09:18 +1000)]
drm/ast: add AST 2400 support.
This is ported from the userspace driver.
Untested on any ast2400 hw so far.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 17 Jan 2014 00:56:09 +0000 (10:56 +1000)]
drm/ast: add widescreen + rb modes from X.org driver (v2)
This syncs up the mode code from the X.org driver upstream,
and adds the mode validation step for hw that doesn't have
widescreen.
v2: (from Egbert Eich <eich@suse.de)
squash drm/ast: Use correct structure member for mode validation
to avoid bisect regression.
In struct drm_display_mode crtc_hdisplay and crtc_vdisplay are holding
the crtc parameters after mode fixup. For validation we need hdisplay and
vdisplay.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Sun, 18 May 2014 21:42:27 +0000 (07:42 +1000)]
Merge tag 'drm-intel-next-2014-05-06' of git://anongit.freedesktop.org/drm-intel into drm-next
- ring init improvements (Chris)
- vebox2 support (Zhao Yakui)
- more prep work for runtime pm on Baytrail (Imre)
- eDram support for BDW (Ben)
- prep work for userptr support (Chris)
- first parts of the encoder->mode_set callback removal (Daniel)
- 64b reloc fixes (Ben)
- first part of atomic plane updates (Ville)
* tag 'drm-intel-next-2014-05-06' of git://anongit.freedesktop.org/drm-intel: (75 commits)
drm/i915: Remove useless checks from primary enable/disable
drm/i915: Merge LP1+ watermarks in safer way
drm/i915: Make sure computed watermarks never overflow the registers
drm/i915: Add pipe update trace points
drm/i915: Perform primary enable/disable atomically with sprite updates
drm/i915: Make sprite updates atomic
drm/i915: Support 64b relocations
drm/i915: Support 64b execbuf
drm/i915/sdvo: Remove ->mode_set callback
drm/i915/crt: Remove ->mode_set callback
drm/i915/tv: Remove ->mode_set callback
drm/i915/tv: Rip out pipe-disabling nonsense from ->mode_set
drm/i915/tv: De-magic device check
drm/i915/tv: extract set_color_conversion
drm/i915/tv: extract set_tv_mode_timings
drm/i915/dvo: Remove ->mode_set callback
drm/i915: Make encoder->mode_set callbacks optional
drm/i915: Make primary_enabled match the actual hardware state
drm/i915: Move ring_begin to signal()
drm/i915: Virtualize the ringbuffer signal func
...
Chris Wilson [Fri, 16 May 2014 17:59:00 +0000 (18:59 +0100)]
drm/i915: Only unpin the default ctx object if it exists
Since commit
691e6415c891b8b2b082a120b896b443531c4d45
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Apr 9 09:07:36 2014 +0100
drm/i915: Always use kref tracking for all contexts.
we have contexts everywhere, and so we must be careful to distinguish
fake contexts, which do not have an associated bo, and real ones, which
do. In particular, we now need to be careful not to dereference NULL
pointers.
This is one such example, as the commit highlighted above failed to move
the unpinning of the default ctx object into the real-context-only
branch.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78792
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 16 May 2014 16:40:23 +0000 (19:40 +0300)]
drm/i915: Convert uncleared FIFO underrun message to errors
Some platforms have a shared error interrupt, so if FIFO underrun
reporting gets disabled for one pipe/transcoder it gets disabled
for all pipes/transcoders.
When we disable FIFO underrun reporting we check whether the
interrupt was enabled or not. If it wasn't we might have missed
an underrun and we perform one last check right there. Currently
we print a debug message when an underrun is detect using this
mechanism. Promote the message to DRM_ERROR() to match the other
underrun error messages.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 16 May 2014 13:22:37 +0000 (14:22 +0100)]
drm/i915: Introduce mapping of user pages into video memory (userptr) ioctl
By exporting the ability to map user address and inserting PTEs
representing their backing pages into the GTT, we can exploit UMA in order
to utilize normal application data as a texture source or even as a
render target (depending upon the capabilities of the chipset). This has
a number of uses, with zero-copy downloads to the GPU and efficient
readback making the intermixed streaming of CPU and GPU operations
fairly efficient. This ability has many widespread implications from
faster rendering of client-side software rasterisers (chromium),
mitigation of stalls due to read back (firefox) and to faster pipelining
of texture data (such as pixel buffer objects in GL or data blobs in CL).
v2: Compile with CONFIG_MMU_NOTIFIER
v3: We can sleep while performing invalidate-range, which we can utilise
to drop our page references prior to the kernel manipulating the vma
(for either discard or cloning) and so protect normal users.
v4: Only run the invalidate notifier if the range intercepts the bo.
v5: Prevent userspace from attempting to GTT mmap non-page aligned buffers
v6: Recheck after reacquire mutex for lost mmu.
v7: Fix implicit padding of ioctl struct by rounding to next 64bit boundary.
v8: Fix rebasing error after forwarding porting the back port.
v9: Limit the userptr to page aligned entries. We now expect userspace
to handle all the offset-in-page adjustments itself.
v10: Prevent vma from being copied across fork to avoid issues with cow.
v11: Drop vma behaviour changes -- locking is nigh on impossible.
Use a worker to load user pages to avoid lock inversions.
v12: Use get_task_mm()/mmput() for correct refcounting of mm.
v13: Use a worker to release the mmu_notifier to avoid lock inversion
v14: Decouple mmu_notifier from struct_mutex using a custom mmu_notifer
with its own locking and tree of objects for each mm/mmu_notifier.
v15: Prevent overlapping userptr objects, and invalidate all objects
within the mmu_notifier range
v16: Fix a typo for iterating over multiple objects in the range and
rearrange error path to destroy the mmu_notifier locklessly.
Also close a race between invalidate_range and the get_pages_worker.
v17: Close a race between get_pages_worker/invalidate_range and fresh
allocations of the same userptr range - and notice that
struct_mutex was presumed to be held when during creation it wasn't.
v18: Sigh. Fix the refactor of st_set_pages() to allocate enough memory
for the struct sg_table and to clear it before reporting an error.
v19: Always error out on read-only userptr requests as we don't have the
hardware infrastructure to support them at the moment.
v20: Refuse to implement read-only support until we have the required
infrastructure - but reserve the bit in flags for future use.
v21: use_mm() is not required for get_user_pages(). It is only meant to
be used to fix up the kernel thread's current->mm for use with
copy_user().
v22: Use sg_alloc_table_from_pages for that chunky feeling
v23: Export a function for sanity checking dma-buf rather than encode
userptr details elsewhere, and clean up comments based on
suggestions by Bradley.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Gong, Zhipeng" <zhipeng.gong@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Cc: "Volkin, Bradley D" <bradley.d.volkin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
[danvet: Frob ioctl allocation to pick the next one - will cause a bit
of fuss with create2 apparently, but such are the rules.]
[danvet2: oops, forgot to git add after manual patch application]
[danvet3: Appease sparse.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Fri, 16 May 2014 10:44:12 +0000 (13:44 +0300)]
drm/i915: Be careful with non-disp bit in PMINTRMSK
Bit 31 in GEN6_PMINTRMSK is not an interrupt disable bit with gen8.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Oscar Mateo [Fri, 16 May 2014 13:20:43 +0000 (14:20 +0100)]
drm/i915: Gracefully handle obj not bound to GGTT in is_pin_display
Otherwise, we do a NULL pointer dereference.
I've seen this happen while handling an error in
i915_gem_object_pin_to_display_plane():
If i915_gem_object_set_cache_level() fails, we call is_pin_display()
to handle the error. At this point, the object is still not pinned
to GGTT and maybe not even bound, so we have to check before we
dereference its GGTT vma.
The IGT kms_flip/bo-too-big tests for this bug.
v2: Chris Wilson says restoring the old value is easier, but that
is_pin_display is useful as a theory of operation. Take the solomonic
decision: at least this way is_pin_display is a little more robust
(until Chris can kill it off).
v3: Chris suggests the WARN in i915_gem_obj_to_ggtt has outlived its
usefulness: add a reminder to remove it.
Issue: VIZ-3772
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Testcase: igt/kms_flip/bo-too-big
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>