OSDN Git Service
Philippe Reynes [Sat, 10 Dec 2016 14:00:48 +0000 (15:00 +0100)]
net: nicvf: use new api ethtool_{get|set}_link_ksettings
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Sat, 10 Dec 2016 12:23:50 +0000 (14:23 +0200)]
net: ethernet: ti: cpsw: sync rates for channels in dual emac mode
The channels are common for both ndevs in dual emac mode. Hence, keep
in sync their rates.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Sat, 10 Dec 2016 12:23:49 +0000 (14:23 +0200)]
net: ethernet: ti: cpsw: re-split res only when speed is changed
Don't re-split res in the following cases:
- speed of phys is not changed
- speed of phys is changed and no rate limited channels
- speed of phys is changed and all channels are rate limited
- phy is unlinked while dev is open
- phy is linked back but speed is not changed
The maximum speed is sum of "linked" phys, thus res are split taken
in account two interfaces, both for dual emac mode and for
switch mode.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Sat, 10 Dec 2016 12:23:48 +0000 (14:23 +0200)]
net: ethernet: ti: cpsw: combine budget and weight split and check
Re-split weight along with budget. It simplify code a little
and update state after every rate change. Also it's necessarily
to move arguments checks to this combined function. Replace
maximum rate check for an interface on maximum possible rate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Sat, 10 Dec 2016 12:23:47 +0000 (14:23 +0200)]
net: ethernet: ti: cpsw: don't start queue twice
No need to start queues after cpsw is started as it will be done
while cpsw_adjust_link(), after phy connection.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Sat, 10 Dec 2016 12:23:46 +0000 (14:23 +0200)]
net: ethernet: ti: cpsw: use same macros to get active slave
Use the same, more convenient macros, to get active slave.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Sat, 10 Dec 2016 10:38:32 +0000 (11:38 +0100)]
net: mvneta: select GENERIC_ALLOCATOR
We previously relied on GENERIC_ALLOCATOR to be selected by CONFIG_ARM,
but now we can compile-test the driver on other architectures that
don't select it:
drivers/net/built-in.o: In function `mvneta_bm_remove':
mvneta_bm.c:(.text+0x4ee35): undefined reference to `gen_pool_free'
This adds an explicit select for the part of the driver that has
the dependency.
Fixes:
a0627f776a45 ("net: marvell: Allow drivers to be built with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kushwaha [Sat, 10 Dec 2016 05:44:47 +0000 (11:14 +0530)]
net: socket: removed an unnecessary newline
This patch removes a newline which was added
in socket.c file in net-next
Signed-off-by: Amit Kushwaha <kushwaha.a@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Sat, 10 Dec 2016 05:10:59 +0000 (21:10 -0800)]
netlink: use blocking notifier
netlink_chain is called in ->release(), which is apparently
a process context, so we don't have to use an atomic notifier
here.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 10 Dec 2016 21:21:55 +0000 (16:21 -0500)]
Merge git://git./linux/kernel/git/davem/net
Linus Torvalds [Sat, 10 Dec 2016 17:47:13 +0000 (09:47 -0800)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- Fix pointer size when caam is used with AArch64 boot loader on
AArch32 kernel.
- Fix ahash state corruption in marvell driver.
- Fix buggy algif_aed tag handling.
- Prevent mcryptd from being used with incompatible algorithms which
can cause crashes"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: algif_aead - fix uninitialized variable warning
crypto: mcryptd - Check mcryptd algorithm compatibility
crypto: algif_aead - fix AEAD tag memory handling
crypto: caam - fix pointer size for AArch64 boot loader, AArch32 kernel
crypto: marvell - Don't corrupt state of an STD req for re-stepped ahash
crypto: marvell - Don't copy hash operation twice into the SRAM
Linus Torvalds [Sat, 10 Dec 2016 17:23:19 +0000 (09:23 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Limit the number of can filters to avoid > MAX_ORDER allocations.
Fix from Marc Kleine-Budde.
2) Limit GSO max size in netvsc driver to avoid problems with NVGRE
configurations. From Stephen Hemminger.
3) Return proper error when memory allocation fails in
ser_gigaset_init(), from Dan Carpenter.
4) Missing linkage undo in error paths of ipvlan_link_new(), from Gao
Feng.
5) Missing necessayr SET_NETDEV_DEV in lantiq and cpmac drivers, from
Florian Fainelli.
6) Handle probe deferral properly in smsc911x driver.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: mlx5: Fix Kconfig help text
net: smsc911x: back out silently on probe deferrals
ibmveth: set correct gso_size and gso_type
net: ethernet: cpmac: Call SET_NETDEV_DEV()
net: ethernet: lantiq_etop: Call SET_NETDEV_DEV()
vhost-vsock: fix orphan connection reset
cxgb4/cxgb4vf: Assign netdev->dev_port with port ID
driver: ipvlan: Unlink the upper dev when ipvlan_link_new failed
ser_gigaset: return -ENOMEM on error instead of success
NET: usb: cdc_mbim: add quirk for supporting Telit LE922A
can: peak: fix bad memory access and free sequence
phy: Don't increment MDIO bus refcount unless it's a different owner
netvsc: reduce maximum GSO size
drivers: net: cpsw-phy-sel: Clear RGMII_IDMODE on "rgmii" links
can: raw: raw_setsockopt: limit number of can_filter that can be set
Christopher Covington [Fri, 9 Dec 2016 21:53:05 +0000 (16:53 -0500)]
net: mlx5: Fix Kconfig help text
Since the following commit, Infiniband and Ethernet have not been
mutually exclusive.
Fixes:
4aa17b28 mlx5: Enable mutual support for IB and Ethernet
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 9 Dec 2016 16:02:05 +0000 (08:02 -0800)]
net: skb_condense() can also deal with empty skbs
It seems attackers can also send UDP packets with no payload at all.
skb_condense() can still be a win in this case.
It will be possible to replace the custom code in tcp_add_backlog()
to get full benefit from skb_condense()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Fri, 9 Dec 2016 13:18:00 +0000 (14:18 +0100)]
net: smsc911x: back out silently on probe deferrals
When trying to get a regulator we may get deferred and we see
this noise:
smsc911x
1b800000.ethernet-ebi2 (unnamed net_device) (uninitialized):
couldn't get regulators -517
Then the driver continues anyway. Which means that the regulator
may not be properly retrieved and reference counted, and may be
switched off in case noone else is using it.
Fix this by returning silently on deferred probe and let the
system work it out.
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 10 Dec 2016 03:59:05 +0000 (22:59 -0500)]
Merge tag 'mac80211-next-for-davem-2016-12-09' of git://git./linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Three fixes:
* fix a logic bug introduced by a previous cleanup
* fix nl80211 attribute confusing (trying to use
a single attribute for two purposes)
* fix a long-standing BSS leak that happens when an
association attempt is abandoned
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Thu, 8 Dec 2016 22:40:03 +0000 (16:40 -0600)]
ibmveth: set correct gso_size and gso_type
This patch is based on an earlier one submitted
by Jon Maxwell with the following commit message:
"We recently encountered a bug where a few customers using ibmveth on the
same LPAR hit an issue where a TCP session hung when large receive was
enabled. Closer analysis revealed that the session was stuck because the
one side was advertising a zero window repeatedly.
We narrowed this down to the fact the ibmveth driver did not set gso_size
which is translated by TCP into the MSS later up the stack. The MSS is
used to calculate the TCP window size and as that was abnormally large,
it was calculating a zero window, even although the sockets receive buffer
was completely empty."
We rely on the Virtual I/O Server partition in a pseries
environment to provide the MSS through the TCP header checksum
field. The stipulation is that users should not disable checksum
offloading if rx packet aggregation is enabled through VIOS.
Some firmware offerings provide the MSS in the RX buffer.
This is signalled by a bit in the RX queue descriptor.
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Reviewed-by: David Dai <zdai@us.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 10 Dec 2016 03:12:30 +0000 (22:12 -0500)]
Merge branch 'udp-receive-path-optimizations'
Eric Dumazet says:
====================
udp: receive path optimizations
This patch series provides about 100 % performance increase under flood.
v2: added Paolo feedback on udp_rmem_release() for tiny sk_rcvbuf
added the last patch touching sk_rmem_alloc later
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 8 Dec 2016 19:41:57 +0000 (11:41 -0800)]
udp: udp_rmem_release() should touch sk_rmem_alloc later
In flood situations, keeping sk_rmem_alloc at a high value
prevents producers from touching the socket.
It makes sense to lower sk_rmem_alloc only at the end
of udp_rmem_release() after the thread draining receive
queue in udp_recvmsg() finished the writes to sk_forward_alloc.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 8 Dec 2016 19:41:56 +0000 (11:41 -0800)]
udp: add batching to udp_rmem_release()
If udp_recvmsg() constantly releases sk_rmem_alloc
for every read packet, it gives opportunity for
producers to immediately grab spinlocks and desperatly
try adding another packet, causing false sharing.
We can add a simple heuristic to give the signal
by batches of ~25 % of the queue capacity.
This patch considerably increases performance under
flood by about 50 %, since the thread draining the queue
is no longer slowed by false sharing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 8 Dec 2016 19:41:55 +0000 (11:41 -0800)]
udp: copy skb->truesize in the first cache line
In UDP RX handler, we currently clear skb->dev before skb
is added to receive queue, because device pointer is no longer
available once we exit from RCU section.
Since this first cache line is always hot, lets reuse this space
to store skb->truesize and thus avoid a cache line miss at
udp_recvmsg()/udp_skb_destructor time while receive queue
spinlock is held.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 8 Dec 2016 19:41:54 +0000 (11:41 -0800)]
udp: add busylocks in RX path
Idea of busylocks is to let producers grab an extra spinlock
to relieve pressure on the receive_queue spinlock shared by consumer.
This behavior is requested only once socket receive queue is above
half occupancy.
Under flood, this means that only one producer can be in line
trying to acquire the receive_queue spinlock.
These busylock can be allocated on a per cpu manner, instead of a
per socket one (that would consume a cache line per socket)
This patch considerably improves UDP behavior under stress,
depending on number of NIC RX queues and/or RPS spread.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 10 Dec 2016 03:11:15 +0000 (22:11 -0500)]
Merge branch 'qcom-emac'
Timur Tabi says:
====================
net: qcom/emac: simplify support for different SOCs
On SOCs that have the Qualcomm EMAC network controller, the internal
PHY block is always different. Sometimes the differences are small,
sometimes it might be a completely different IP. Either way, using version
numbers to differentiate them and putting all of the init code in one
file does not scale.
This patchset does two things: The first breaks up the current code into
different files, and the second patch adds support for a third SOC, the
Qualcomm Technologies QDF2400 ARM Server SOC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Thu, 8 Dec 2016 19:24:21 +0000 (13:24 -0600)]
net: qcom/emac: add support for the Qualcomm Technologies QDF2400
The QDF2432 and the QDF2400 have slightly different internal PHYs,
so there are some programming differences. Some of the registers in
the QDF2400 have moved, and some registers require different values
during initialization.
Because of the differences, and because HIDs are a scare resource,
the ACPI tables specify the hardware version in an _HRV property.
Version 1 is the QDF2432, and version 2 is the QDF2400. Any future
SOC that has the same internal PHY but different programming
requirements will be assigned the next available version number.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Thu, 8 Dec 2016 19:24:20 +0000 (13:24 -0600)]
net: qcom/emac: move phy init code to separate files
The internal PHY of the EMAC differs on each SOC, and the list will
only continue to grow. By separating the code into individual files,
we can add support for more SOCs more cleanly.
Note: The internal PHY is also sometimes called the SGMII device.
We also stop referring to the various PHY variations by version number,
so no more "v2", "v3", etc. Instead, the devices are named after the
SOC they are, which is in sync with the device tree property names.
Future patches will probably rearrange more code among the files.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 9 Dec 2016 19:27:22 +0000 (11:27 -0800)]
Merge branch 'libnvdimm-fixes' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"Several fixes to the DSM (ACPI device specific method) marshaling
implementation.
I consider these urgent enough to send for 4.9 consideration since
they fix the kernel's handling of ARS (Address Range Scrub) commands.
Especially for platforms without machine-check-recovery capabilities,
successful execution of ARS commands enables the platform to
potentially break out of an infinite reboot problem if a media error
is present in the boot path. There is also a one line fix for a
device-dax read-only mapping regression.
Commits
9a901f5495e2 ("acpi, nfit: fix extended status translations
for ACPI DSMs") and
325896ffdf90 ("device-dax: fix private mapping
restriction, permit read-only") are true regression fixes for changes
introduced this cycle.
Commit
efda1b5d87cb ("acpi, nfit, libnvdimm: fix / harden ars_status
output length handling") fixes the kernel's handling of zero-length
results, this never would have worked in the past, but we only just
recently discovered a BIOS implementation that emits this arguably
spec non-compliant result.
The remaining two commits are additional fall out from thinking
through the implications of a zero / truncated length result of the
ARS Status command.
In order to mitigate the risk that these changes introduce yet more
regressions they are backstopped by a new unit test in commit
a7de92dac9f0 ("tools/testing/nvdimm: unit test acpi_nfit_ctl()") that
mocks up inputs to acpi_nfit_ctl()"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: fix private mapping restriction, permit read-only
tools/testing/nvdimm: unit test acpi_nfit_ctl()
acpi, nfit: fix bus vs dimm confusion in xlat_status
acpi, nfit: validate ars_status output buffer size
acpi, nfit, libnvdimm: fix / harden ars_status output length handling
acpi, nfit: fix extended status translations for ACPI DSMs
Linus Torvalds [Fri, 9 Dec 2016 19:07:45 +0000 (11:07 -0800)]
Merge branch 'for-4.9-fixes' of git://git./linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"This is quite late but SCT Write Same support added during this cycle
is broken subtly but seriously and it'd be best to disable it before
v4.9 gets released.
This contains two commits - one low impact sata_mv fix and the
mentioned disabling of SCT Write Same"
* 'for-4.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata-scsi: disable SCT Write Same for the moment
ata: sata_mv: check for errors when parsing nr-ports from dt
Linus Torvalds [Fri, 9 Dec 2016 19:02:40 +0000 (11:02 -0800)]
Merge tag 'ceph-for-4.9-rc9' of git://github.com/ceph/ceph-client
Pull ceph fix from Ilya Dryomov:
"A fix for an issue with ->d_revalidate() in ceph, causing frequent
kernel crashes.
Marked for stable - it goes back to 4.6, but started popping up only
in 4.8"
* tag 'ceph-for-4.9-rc9' of git://github.com/ceph/ceph-client:
ceph: don't set req->r_locked_dir in ceph_d_revalidate
Linus Torvalds [Fri, 9 Dec 2016 19:00:39 +0000 (11:00 -0800)]
Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Final batch of SoC fixes
A few fixes that have trickled in over the last week, all fixing minor
errors in devicetrees -- UART pin assignment on Allwinner H3,
correcting number of SATA ports on a Marvell-based Linkstation
platform and a display clock fix for Freescale/NXP i.MX7D that fixes a
freeze when starting up X"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: orion5x: fix number of sata port for linkstation ls-gl
ARM: dts: imx7d: fix LCDIF clock assignment
dts: sun8i-h3: correct UART3 pin definitions
Linus Torvalds [Fri, 9 Dec 2016 18:54:54 +0000 (10:54 -0800)]
Merge tag 'm68k-for-v4.9-tag2' of git://git./linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
- build fix for drivers calling ndelay() in a conditional block without
curly braces
- defconfig updates
* tag 'm68k-for-v4.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Fix ndelay() macro
m68k/defconfig: Update defconfigs for v4.9-rc1
Linus Torvalds [Fri, 9 Dec 2016 18:50:49 +0000 (10:50 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fix from Dave Airlie:
"Just a single fix for amdgpu to just suspend the gpu on 'shutdown'
instead of shutting it down fully, as for some reason the hw was
getting upset in some situations"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: just suspend the hw on pci shutdown
Linus Torvalds [Fri, 9 Dec 2016 18:41:42 +0000 (10:41 -0800)]
Revert "radix tree test suite: fix compilation"
This reverts commit
53855d10f4567a0577360b6448d52a863929775b.
It shouldn't have come in yet - it depends on the changes in linux-next
that will come in during the next merge window. As Matthew Wilcox says,
the test suite is broken with the current state without the revert.
Requested-by: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Thu, 8 Dec 2016 16:22:09 +0000 (17:22 +0100)]
cfg80211/mac80211: fix BSS leaks when abandoning assoc attempts
When mac80211 abandons an association attempt, it may free
all the data structures, but inform cfg80211 and userspace
about it only by sending the deauth frame it received, in
which case cfg80211 has no link to the BSS struct that was
used and will not cfg80211_unhold_bss() it.
Fix this by providing a way to inform cfg80211 of this with
the BSS entry passed, so that it can clean up properly, and
use this ability in the appropriate places in mac80211.
This isn't ideal: some code is more or less duplicated and
tracing is missing. However, it's a fairly small change and
it's thus easier to backport - cleanups can come later.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Vamsi Krishna [Fri, 2 Dec 2016 21:59:08 +0000 (23:59 +0200)]
nl80211: Use different attrs for BSSID and random MAC addr in scan req
NL80211_ATTR_MAC was used to set both the specific BSSID to be scanned
and the random MAC address to be used when privacy is enabled. When both
the features are enabled, both the BSSID and the local MAC address were
getting same value causing Probe Request frames to go with unintended
DA. Hence, this has been fixed by using a different NL80211_ATTR_BSSID
attribute to set the specific BSSID (which was the more recent addition
in cfg80211) for a scan.
Backwards compatibility with old userspace software is maintained to
some extent by allowing NL80211_ATTR_MAC to be used to set the specific
BSSID when scanning without enabling random MAC address use.
Scanning with random source MAC address was introduced by commit
ad2b26abc157 ("cfg80211: allow drivers to support random MAC addresses
for scan") and the issue was introduced with the addition of the second
user for the same attribute in commit
818965d39177 ("cfg80211: Allow a
scan request for a specific BSSID").
Fixes:
818965d39177 ("cfg80211: Allow a scan request for a specific BSSID")
Signed-off-by: Vamsi Krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 21 Nov 2016 12:55:48 +0000 (13:55 +0100)]
nl80211: fix logic inversion in start_nan()
Arend inadvertently inverted the logic while converting to
wdev_running(), fix that.
Fixes:
73c7da3dae1e ("cfg80211: add generic helper to check interface is running")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arnd Bergmann [Thu, 8 Dec 2016 21:57:05 +0000 (22:57 +0100)]
net: xgene: avoid bogus maybe-uninitialized warning
In some configurations, gcc cannot trace the state of variables
across a spin_unlock() barrier, leading to a warning about
correct code:
xgene_enet_main.c: In function 'xgene_enet_start_xmit':
../../../phy/mdio-xgene.h:112:14: error: 'mss_index' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Here we can trivially move the assignment before that spin_unlock,
which reliably avoids the warning.
Fixes:
e3978673f514 ("drivers: net: xgene: Fix MSS programming")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 8 Dec 2016 21:57:04 +0000 (22:57 +0100)]
net: xgene: move xgene_cle_ptree_ewdn data off stack
The array for initializing the cle is set up on the stack with
almost entirely constant data and then passed to a function that
converts it into HW specific bit patterns. With the latest
addition, the size of this array has grown to the point that
we get a warning about potential stack overflow in allmodconfig
builds:
xgene_enet_cle.c: In function ‘xgene_enet_cle_init’:
xgene_enet_cle.c:836:1: error: the frame size of 1032 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Looking a bit deeper at the usage, I noticed that the only modification
of the data is in dead code, as we don't even use the cle module
for phy_mode other than PHY_INTERFACE_MODE_XGMII. This means we
can simply mark the structure constant and access it directly rather
than passing the pointer down through another structure, making
the code more efficient at the same time as avoiding the
warning.
Fixes:
a809701fed15 ("drivers: net: xgene: fix: RSS for non-TCP/UDP")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 8 Dec 2016 21:57:03 +0000 (22:57 +0100)]
net/mlx5e: use %pad format string for dma_addr_t
On 32-bit ARM with 64-bit dma_addr_t I get this warning about an
incorrect format string:
In file included from /git/arm-soc/drivers/net/ethernet/mellanox/mlx5/core/alloc.c:42:0:
drivers/net/ethernet/mellanox/mlx5/core/alloc.c: In function ‘mlx5_frag_buf_alloc_node’:
drivers/net/ethernet/mellanox/mlx5/core/alloc.c:134:12: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
We have the special %pad format for printing dma_addr_t, so use that
to print the correct address and avoid the warning.
Fixes:
1c1b522808a1 ("net/mlx5e: Implement Fragmented Work Queue (WQ)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 9 Dec 2016 02:26:59 +0000 (21:26 -0500)]
Merge branch 'ethernet-missing-netdev-parent'
Florian Fainelli says:
====================
net: ethernet: Make sure we set dev->dev.parent
This patch series builds atop:
ec988ad78ed6d184a7f4ca6b8e962b0e8f1de461 ("phy: Don't increment MDIO
bus refcount unless it's a different owner")
FMAN is the one that potentially needs patching as well (call
SET_NETDEV_DEV), but there appears to be no way that init_phy is
called right now, or there is not such an in-tree user. Madalin, can
you comment on that?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 8 Dec 2016 19:41:25 +0000 (11:41 -0800)]
net: ethernet: cpmac: Call SET_NETDEV_DEV()
The TI CPMAC driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes:
ec988ad78ed6 ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 8 Dec 2016 19:41:24 +0000 (11:41 -0800)]
net: ethernet: lantiq_etop: Call SET_NETDEV_DEV()
The Lantiq Etop driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes:
ec988ad78ed6 ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Tao [Thu, 8 Dec 2016 17:10:46 +0000 (01:10 +0800)]
vhost-vsock: fix orphan connection reset
local_addr.svm_cid is host cid. We should check guest cid instead,
which is remote_addr.svm_cid. Otherwise we end up resetting all
connections to all guests.
Cc: stable@vger.kernel.org [4.8+]
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 8 Dec 2016 23:40:15 +0000 (15:40 -0800)]
Merge branch 'parisc-4.9-5' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Three important fixes for the parisc architecture.
Dave provided two patches: One which purges the TLB before setting a
PTE entry and a second one which drops unnecessary TLB flushes. Both
patches have been tested for one week on the debian buildd servers and
prevent random segmentation faults.
The patch from me fixes a crash at boot inside the TLB measuring code
on SMP machines with PA8000-PA8700 CPUs (specifically A500-44 and
J5000 servers)"
* 'parisc-4.9-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix TLB related boot crash on SMP machines
parisc: Remove unnecessary TLB purges from flush_dcache_page_asm and flush_icache_page_asm
parisc: Purge TLB before setting PTE
David S. Miller [Thu, 8 Dec 2016 23:22:40 +0000 (18:22 -0500)]
Merge tag 'linux-can-fixes-for-4.9-
20161208' of git://git./linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-12-08
this is a pull request for one patch.
Jiho Chu found and fixed a use-after-free error in the cleanup path in
the peak pcan USB CAN driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kushwaha [Thu, 8 Dec 2016 12:51:53 +0000 (18:21 +0530)]
net: socket: preferred __aligned(size) for control buffer
This patch cleanup checkpatch.pl warning
WARNING: __aligned(size) is preferred over __attribute__((aligned(size)))
Signed-off-by: Amit Kushwaha <kushwaha.a@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arjun V [Thu, 8 Dec 2016 12:39:23 +0000 (18:09 +0530)]
cxgb4/cxgb4vf: Assign netdev->dev_port with port ID
Added missing dev_port assignment in cxgb4vf driver.
Also made dev_port assignment of cxgb4 in sync with cxgb4vf driver.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Dec 2016 23:16:52 +0000 (18:16 -0500)]
Merge branch 'liquidio-VF-offloads-and-stats'
Raghu Vatsavayi says:
====================
liquidio VF offloads and stats
Following is final patch series in completing the liquidio
VF driver support. These patches have minor changes related
to offloads and stats.
Please apply patches in following order as some of them
depend on earlier patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Thu, 8 Dec 2016 21:00:48 +0000 (13:00 -0800)]
liquidio VF error handling
Adds support for VF error handling.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Thu, 8 Dec 2016 21:00:47 +0000 (13:00 -0800)]
liquidio VF timestamp
Adds support for VF timestamp.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Thu, 8 Dec 2016 21:00:46 +0000 (13:00 -0800)]
liquidio VF ethtool stats
Adds support for VF ethtool stats
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Thu, 8 Dec 2016 21:00:45 +0000 (13:00 -0800)]
liquidio VF vxlan
Adds VF vxlan offload support.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Thu, 8 Dec 2016 21:00:44 +0000 (13:00 -0800)]
liquidio VF vlan support
Adds support for VF vlan features.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Helge Deller [Thu, 8 Dec 2016 20:00:46 +0000 (21:00 +0100)]
parisc: Fix TLB related boot crash on SMP machines
At bootup we run measurements to calculate the best threshold for when we
should be using full TLB flushes instead of just flushing a specific amount of
TLB entries. This performance test is run over the kernel text segment.
But running this TLB performance test on the kernel text segment turned out to
crash some SMP machines when the kernel text pages were mapped as huge pages.
To avoid those crashes this patch simply skips this test on some SMP machines
and calculates an optimal threshold based on the maximum number of available
TLB entries and number of online CPUs.
On a technical side, this seems to happen:
The TLB measurement code uses flush_tlb_kernel_range() to flush specific TLB
entries with a page size of 4k (pdtlb 0(sr1,addr)). On UP systems this purge
instruction seems to work without problems even if the pages were mapped as
huge pages. But on SMP systems the TLB purge instruction is broadcasted to
other CPUs. Those CPUs then crash the machine because the page size is not as
expected. C8000 machines with PA8800/PA8900 CPUs were not affected by this
problem, because the required cache coherency prohibits to use huge pages at
all. Sadly I didn't found any documentation about this behaviour, so this
finding is purely based on testing with phyiscal SMP machines (A500-44 and
J5000, both were 2-way boxes).
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Helge Deller <deller@gmx.de>
Linus Torvalds [Thu, 8 Dec 2016 20:04:41 +0000 (12:04 -0800)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One small fix for a regression in a prior fix (again).
This time the condition in the prior fix BUG_ON proved to be wrong
under certain circumstances causing a BUG to trigger where it
shouldn't in the lpfc driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: fix oops/BUG in lpfc_sli_ringtxcmpl_put()
David S. Miller [Thu, 8 Dec 2016 19:33:17 +0000 (14:33 -0500)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-12-08
I didn't miss your "net-next is closed" email, but it did come as a bit
of a surprise, and due to time-zone differences I didn't have a chance
to react to it until now. We would have had a couple of patches in
bluetooth-next that we'd still have wanted to get to 4.10.
Out of these the most critical one is the H7/CT2 patch for Bluetooth
Security Manager Protocol, something that couldn't be published before
the Bluetooth 5.0 specification went public (yesterday). If these really
can't go to net-next we'll likely be sending at least this patch through
bluetooth.git to net.git for rc1 inclusion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Thu, 8 Dec 2016 07:46:25 +0000 (13:16 +0530)]
cxgb4/cxgb4vf: Remove deprecated module parameters
Remove deprecated module parameters num_vf, dflt_msg_enable and
force_init.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gao Feng [Thu, 8 Dec 2016 03:16:58 +0000 (11:16 +0800)]
driver: ipvlan: Unlink the upper dev when ipvlan_link_new failed
When netdev_upper_dev_unlink failed in ipvlan_link_new, need to
unlink the ipvlan dev with upper dev.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Dec 2016 19:25:14 +0000 (14:25 -0500)]
Merge branch 'xdp-head-adjustment'
Martin KaFai Lau says:
====================
Allow head adjustment in XDP prog
This series adds a helper to allow head adjusting in XDP prog. mlx4
driver has been modified to support this feature. An example is written
to encapsulate a packet with an IPv4/v6 header and then XDP_TX it
out.
v4:
1. Remove XDP_QUERY_FEATURES command. Instead, check
the prog->xdp_adjust_head bit inside the driver itself
during XDP_SETUP_PROG in patch 1of4.
Thanks for everybody's ideas.
2. Nit changes on sample code per Jesper
v3:
1. Check if the driver supports head adjustment before
setting the xdp_prog fd to the device in patch 1of4.
2. Remove the page alignment assumption on the data_hard_start.
Instead, add data_hard_start to the struct xdp_buff and the
driver has to fill it if it supports head adjustment.
3. Keep the wire MTU as before in mlx4
4. Set map0_byte_count to PAGE_SIZE in patch 3of4
v2:
1. Make a variable name change in bpf_xdp_adjust_head() in patch 1
2. Ensure no less than ETH_HLEN data in bpf_xdp_adjust_head() in patch 1
3. Some clarifications in commit log messages of patch 2 and 3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Wed, 7 Dec 2016 23:53:14 +0000 (15:53 -0800)]
bpf: xdp: Add XDP example for head adjustment
The XDP prog checks if the incoming packet matches any VIP:PORT
combination in the BPF hashmap. If it is, it will encapsulate
the packet with a IPv4/v6 header as instructed by the value of
the BPF hashmap and then XDP_TX it out.
The VIP:PORT -> IP-Encap-Info can be specified by the cmd args
of the user prog.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Wed, 7 Dec 2016 23:53:13 +0000 (15:53 -0800)]
mlx4: xdp: Reserve headroom for receiving packet when XDP prog is active
Reserve XDP_PACKET_HEADROOM for packet and enable bpf_xdp_adjust_head()
support. This patch only affects the code path when XDP is active.
After testing, the tx_dropped counter is incremented if the xdp_prog sends
more than wire MTU.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Wed, 7 Dec 2016 23:53:12 +0000 (15:53 -0800)]
mlx4: xdp: Allow raising MTU up to one page minus eth and vlan hdrs
When XDP is active in mlx4, mlx4 is using one page/pkt.
At the same time (i.e. when XDP is active), it is currently
limiting MTU to be FRAG_SZ0 - ETH_HLEN - (2 * VLAN_HLEN)
which is 1514 in x86. AFAICT, we can at least raise the MTU
limit up to PAGE_SIZE - ETH_HLEN - (2 * VLAN_HLEN) which this
patch is doing. It will be useful in the next patch which
allows XDP program to extend the packet by adding new header(s).
Note: In the earlier XDP patches, there is already existing guard
to ensure the page/pkt scheme only applies when XDP is active
in mlx4.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Wed, 7 Dec 2016 23:53:11 +0000 (15:53 -0800)]
bpf: xdp: Allow head adjustment in XDP prog
This patch allows XDP prog to extend/remove the packet
data at the head (like adding or removing header). It is
done by adding a new XDP helper bpf_xdp_adjust_head().
It also renames bpf_helper_changes_skb_data() to
bpf_helper_changes_pkt_data() to better reflect
that XDP prog does not work on skb.
This patch adds one "xdp_adjust_head" bit to bpf_prog for the
XDP-capable driver to check if the XDP prog requires
bpf_xdp_adjust_head() support. The driver can then decide
to error out during XDP_SETUP_PROG.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Dec 2016 19:21:48 +0000 (14:21 -0500)]
Merge branch 'lan7801-mac-only'
Woojung Huh says:
====================
phy: lan78xx: add phy fixup unregister functions & LAN7801 update
V2 patch of adding phy fixup unregister function with use in LAN7801 update.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Woojung Huh [Wed, 7 Dec 2016 20:26:25 +0000 (20:26 +0000)]
lan78xx: add LAN7801 MAC only support
Add LAN7801 MAC only support with phy fixup functions.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Woojung.Huh@microchip.com [Wed, 7 Dec 2016 20:26:07 +0000 (20:26 +0000)]
phy: add phy fixup unregister functions
>From : Woojung Huh <woojung.huh@microchip.com>
Add functions to unregister phy fixup for modules.
int phy_unregister_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list per bus_id, phy_uid &
phy_uid_mask
int phy_unregister_fixup_for_uid(u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_uid()
int phy_unregister_fixup_for_id(const char *bus_id)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_id()
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 7 Dec 2016 11:22:03 +0000 (14:22 +0300)]
ser_gigaset: return -ENOMEM on error instead of success
If we can't allocate the resources in gigaset_initdriver() then we
should return -ENOMEM instead of zero.
Fixes:
2869b23e4b95 ("[PATCH] drivers/isdn/gigaset: new M101 driver (v2)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov [Wed, 7 Dec 2016 18:57:59 +0000 (10:57 -0800)]
bpf: fix state equivalence
Commmits
57a09bf0a416 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL registers")
and
484611357c19 ("bpf: allow access into map value arrays") by themselves
are correct, but in combination they make state equivalence ignore 'id' field
of the register state which can lead to accepting invalid program.
Fixes:
57a09bf0a416 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL registers")
Fixes:
484611357c19 ("bpf: allow access into map value arrays")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 7 Dec 2016 18:05:36 +0000 (10:05 -0800)]
net: do not read sk_drops if application does not care
sk_drops can be an often written field, do not read it unless
application showed interest.
Note that sk_drops can be read via inet_diag, so applications
can avoid getting this info from every received packet.
In the future, 'reading' sk_drops might require folding per node or per
cpu fields, and thus become even more expensive than today.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 7 Dec 2016 17:19:33 +0000 (09:19 -0800)]
udp: under rx pressure, try to condense skbs
Under UDP flood, many softirq producers try to add packets to
UDP receive queue, and one user thread is burning one cpu trying
to dequeue packets as fast as possible.
Two parts of the per packet cost are :
- copying payload from kernel space to user space,
- freeing memory pieces associated with skb.
If socket is under pressure, softirq handler(s) can try to pull in
skb->head the payload of the packet if it fits.
Meaning the softirq handler(s) can free/reuse the page fragment
immediately, instead of letting udp_recvmsg() do this hundreds of usec
later, possibly from another node.
Additional gains :
- We reduce skb->truesize and thus can store more packets per SO_RCVBUF
- We avoid cache line misses at copyout() time and consume_skb() time,
and avoid one put_page() with potential alien freeing on NUMA hosts.
This comes at the cost of a copy, bounded to available tail room, which
is usually small. (We might have to fix GRO_MAX_HEAD which looks bigger
than necessary)
This patch gave me about 5 % increase in throughput in my tests.
skb_condense() helper could probably used in other contexts.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Dec 2016 18:21:40 +0000 (13:21 -0500)]
Merge branch 'liqudio-VF-data-path'
Raghu Vatsavayi says:
====================
liquidio VF data path
Following is V3 patch series that adds support for VF
data path related features. It also has following changes
related to previous comments:
1) Remove unnecessary "void *" casting.
2) Remove inline for functions and let gcc decide.
Please apply patches in following order as some of them
depend on earlier patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 7 Dec 2016 16:54:37 +0000 (08:54 -0800)]
liquidio VF rx data and ctl path
Adds support for VF receive data control path.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 7 Dec 2016 16:54:36 +0000 (08:54 -0800)]
liquidio CN23XX: VF TX buffers
Adds support for freeing VF xmit buffers.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 7 Dec 2016 16:54:35 +0000 (08:54 -0800)]
liquidio CN23XX: VF xmit
Adds support for transmit functionality in VF.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 7 Dec 2016 16:54:34 +0000 (08:54 -0800)]
liquidio CN23XX: VF scatter gather lists
Adds support for VF scatter gather lists.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 7 Dec 2016 16:54:33 +0000 (08:54 -0800)]
liquidio CN23XX: VF mac address
Adds support for configuring mtu, multicast and mac address.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 7 Dec 2016 16:54:32 +0000 (08:54 -0800)]
liquidio CN23XX: VF link status
Adds support for VF link status related changes.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 7 Dec 2016 16:54:31 +0000 (08:54 -0800)]
liquidio CN23XX: VF offload features
Adds support for VF link initialization and offload features.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roger Shimizu [Thu, 1 Dec 2016 15:11:12 +0000 (00:11 +0900)]
ARM: dts: orion5x: fix number of sata port for linkstation ls-gl
Bug report from Debian [0] shows there's minor changed model of
Linkstation LS-GL that uses the 2nd SATA port of the SoC.
So it's necessary to enable two SATA ports, though for that specific
model only the 2nd one is used.
[0] https://bugs.debian.org/845611
Fixes:
b1742ffa9ddb ("ARM: dts: orion5x: add device tree for buffalo linkstation ls-gl")
Reported-by: Ryan Tandy <ryan@nardis.ca>
Tested-by: Ryan Tandy <ryan@nardis.ca>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Eric Dumazet [Wed, 7 Dec 2016 16:29:10 +0000 (08:29 -0800)]
net: rfs: add a jump label
RFS is not commonly used, so add a jump label to avoid some conditionals
in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Shengju [Wed, 7 Dec 2016 15:02:09 +0000 (23:02 +0800)]
macsec: remove first zero and add attribute name in comments
Remove first zero for add, and use full attribute name in comments.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Dec 2016 18:07:11 +0000 (13:07 -0500)]
Merge branch 'stmmac-DMA-burst'
Niklas Cassel says:
====================
net: stmmac: make DMA programmable burst length more configurable
Make DMA programmable burst length more configurable in the stmmac driver.
This is done by adding support for independent pbl for tx/rx through DT.
More fine grained tuning of pbl is possible thanks to a DT property saying
that we should NOT multiply pbl values by x8/x4 in hardware.
All new DT properties are optional, and created in a way that it will not
affect any existing DT configurations.
Changes since V1:
Created cover-letter.
Rebased patch set against next-
20161205, since conflicting patches to
stmmac_platform.c has been merged since V1.
Changes since V2:
Moved default value initialization of pbl to stmmac_platform.c
and added a check for pbl != 0 in stmmac_main.c,
to catch a possble pbl == 0 from pci glue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 14:20:08 +0000 (15:20 +0100)]
net: smmac: allow configuring lower pbl values
The driver currently always sets the PBLx8/PBLx4 bit, which means that
the pbl values configured via the pbl/txpbl/rxpbl DT properties are
always multiplied by 8/4 in the hardware.
In order to allow the DT to configure lower pbl values, while at the
same time not changing behavior of any existing device trees using the
pbl/txpbl/rxpbl settings, add a property to disable the multiplication
of the pbl by 8/4 in the hardware.
Suggested-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 14:20:07 +0000 (15:20 +0100)]
net: stmmac: add support for independent DMA pbl for tx/rx
GMAC and newer supports independent programmable burst lengths for
DMA tx/rx. Add new optional devicetree properties representing this.
To be backwards compatible, snps,pbl will still be valid, but
snps,txpbl/snps,rxpbl will override the value in snps,pbl if set.
If the IP is synthesized to use the AXI interface, there is a register
and a matching DT property inside the optional stmmac-axi-config DT node
for controlling burst lengths, named snps,blen.
However, using this register, it is not possible to control tx and rx
independently. Also, this register is not available if the IP was
synthesized with, e.g., the AHB interface.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 14:20:06 +0000 (15:20 +0100)]
net: stmmac: dwmac1000: fix define DMA_BUS_MODE_RPBL_MASK
DMA_BUS_MODE_RPBL_MASK is really 6 bits,
just like DMA_BUS_MODE_PBL_MASK.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 14:20:05 +0000 (15:20 +0100)]
net: stmmac: stmmac_platform: fix parsing of DT binding
commit
64c3b252e9fc ("net: stmmac: fixed the pbl setting with DT")
changed the parsing of the DT binding.
Before
64c3b252e9fc, snps,fixed-burst and snps,mixed-burst were parsed
regardless if the property snps,pbl existed or not.
After the commit, fixed burst and mixed burst are only parsed if
snps,pbl exists. Now when snps,aal has been added, it too is only
parsed if snps,pbl exists.
Since the DT binding does not specify that fixed burst, mixed burst
or aal depend on snps,pbl being specified, undo changes introduced
by
64c3b252e9fc.
The issue commit
64c3b252e9fc ("net: stmmac: fixed the pbl setting with
DT") tries to address is solved in another way:
The databook specifies that all values other than
1, 2, 4, 8, 16, or 32 results in undefined behavior,
so snps,pbl = <0> is invalid.
If pbl is 0 after parsing, set pbl to DEFAULT_DMA_PBL.
This handles the case where the property is omitted, and also handles
the case where the property is specified without any data.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 14:20:04 +0000 (15:20 +0100)]
net: stmmac: simplify the common DMA init API
Use struct stmmac_dma_cfg *dma_cfg as an argument rather
than using all the struct members as individual arguments.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 14:20:03 +0000 (15:20 +0100)]
net: stmmac: return error if no DMA configuration is found
All drivers except pci glue layer calls stmmac_probe_config_dt.
stmmac_probe_config_dt does a kzalloc dma_cfg.
pci glue layer does kzalloc dma_cfg explicitly, so all current
drivers does a kzalloc dma_cfg.
Return an error if no DMA configuration is found, that way
we can assume that the DMA configuration always exists.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniele Palmas [Wed, 7 Dec 2016 13:07:48 +0000 (14:07 +0100)]
NET: usb: cdc_mbim: add quirk for supporting Telit LE922A
Telit LE922A MBIM based composition does not work properly
with altsetting toggle done in cdc_ncm_bind_common.
This patch adds CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE quirk
to avoid this procedure that, instead, is mandatory for
other modems.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Wed, 7 Dec 2016 13:43:30 +0000 (14:43 +0100)]
net: ethernet: slicoss: use module_pci_driver()
Use module_pci_driver() to get rid of some boilerplate code.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Dec 2016 16:47:14 +0000 (11:47 -0500)]
Merge branch 'cls_flower-ICMP'
Simon Horman says:
====================
net/sched: cls_flower: Support matching on ICMP
this series adds support for matching on ICMP type and code to cls_flower.
Changes v5->v6:
* Restore missing signed-off-by
Changes v4->v5:
* Drop all helpers
Changes v3->v4:
* Do not add icmp to struct flow_keys, it is not needed
* Do not test for ICMP protocols in packet in __skb_flow_dissect,
this is also not needed
Changes v2->v3:
* Add FLOW_DISSECTOR_KEY_ICMP and use separate structure for ICMP
Changes v1->v2:
* Include all dissector helpers in first patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Wed, 7 Dec 2016 12:48:28 +0000 (13:48 +0100)]
net/sched: cls_flower: Support matching on ICMP type and code
Support matching on ICMP type and code.
Example usage:
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ip parent ffff: flower \
indev eth0 ip_proto icmp type 8 code 0 action drop
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 ip_proto icmpv6 type 128 code 0 action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Wed, 7 Dec 2016 12:48:27 +0000 (13:48 +0100)]
flow dissector: ICMP support
Allow dissection of ICMP(V6) type and code. This should only occur
if a packet is ICMP(V6) and the dissector has FLOW_DISSECTOR_KEY_ICMP set.
There are currently no users of FLOW_DISSECTOR_KEY_ICMP.
A follow-up patch will allow FLOW_DISSECTOR_KEY_ICMP to be used by
the flower classifier.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 12:41:08 +0000 (13:41 +0100)]
net: stmmac: stmmac_platform: use correct setup function for gmac4
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
Previously, when specifying "snps,dwmac-4.10a", "snps,dwmac" as your
compatible string, plat_stmmacenet_data would have both has_gmac and
has_gmac4 set.
This would lead to stmmac_hw_init calling dwmac1000_setup rather than
dwmac4_setup, resulting in a non-functional driver.
This happened since the check for has_gmac is done before the check for
has_gmac4. However, the order should not matter, so it does not make sense
to have both set.
If something is valid for both, you should do as the stmmac_interrupt does:
if (priv->plat->has_gmac || priv->plat->has_gmac4) ...
The places where it was obvious that the author actually meant
if (has_gmac || has_gmac4) rather than if (has_gmac) has been updated.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 12:41:07 +0000 (13:41 +0100)]
net: stmmac: dwmac-generic: add missing compatible strings
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
Since dwmac-generic.c calls stmmac_probe_config_dt explicitly,
another alternative would have been to remove all compatible strings
other than "snps,dwmac" and "st,spear600-gmac" from dwmac-generic.c.
However, that would probably do more good than harm, since when trying
to figure out what hardware a certain driver supports, you usually look
at the compatible strings in the struct of_device_id, and not in some
function defined in a completely different file.
No functional change intended.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 12:41:06 +0000 (13:41 +0100)]
bindings: net: stmmac: correct note about TSO
snps,tso was previously placed under AXI BUS Mode parameters,
suggesting that the property should be in the stmmac-axi-config node.
TSO (TCP Segmentation Offloading) has nothing to do with AXI BUS Mode
parameters, and the parser actually expects it to be in the root node,
not in the stmmac-axi-config.
Also added a note about snps,tso only being available on GMAC4 and newer.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Wed, 7 Dec 2016 12:25:29 +0000 (13:25 +0100)]
net: ll_temac: Utilize of_get_mac_address()
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.
Also avoid casting away the const qualifier of the return value by
making temac_init_mac_address() take a const void* address.
Follows commit
b34296a9c047 ("net: ethoc: Utilize
of_get_mac_address()").
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Wed, 7 Dec 2016 12:24:44 +0000 (13:24 +0100)]
net: axienet: Utilize of_get_mac_address()
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.
Also avoid casting away the const qualifier of the return value by
making axienet_set_mac_address() take a const void* address.
Follows commit
b34296a9c047 ("net: ethoc: Utilize
of_get_mac_address()").
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Dec 2016 16:32:50 +0000 (11:32 -0500)]
Merge branch 'cls_flower-flags'
Or Gerlitz says:
====================
net/sched: cls_flower: Add support for matching on dissection flags
This series add the UAPI to provide set of flags for matching, where the
flags provided from user-space are mapped to flow-dissector flags.
The 1st flag allows to match on whether the packet is an
IP fragment and corresponds to the FLOW_DIS_IS_FRAGMENT flag.
v2->v3:
- replace BIT() with << (kbuild test robot)
v1->v2:
- dropped the flow dissector patch (#1) as no changes are needed there (Jiri)
- applied code review comments from Jiri to the flower patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Wed, 7 Dec 2016 12:03:11 +0000 (14:03 +0200)]
net/mlx5e: Offload TC matching on packets being IP fragments
Enable offloading of matching on packets being fragments.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Wed, 7 Dec 2016 12:03:10 +0000 (14:03 +0200)]
net/sched: cls_flower: Add support for matching on flags
Add UAPI to provide set of flags for matching, where the flags
provided from user-space are mapped to flow-dissector flags.
The 1st flag allows to match on whether the packet is an
IP fragment and corresponds to the FLOW_DIS_IS_FRAGMENT flag.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>