OSDN Git Service
Jesse Sung [Thu, 22 Dec 2011 02:48:47 +0000 (10:48 +0800)]
Bluetooth: Add support for BCM20702A0 [0a5c:21e3]
Add another vendor specific ID for BCM20702A0.
output of usb-devices:
T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21e3 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=
9439E5CBF66C
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Brian Gix [Thu, 22 Dec 2011 00:12:13 +0000 (16:12 -0800)]
Bluetooth: Add SMP to User Passkey and Confirm
Low Energy pairing is performed through the SMP (Security Manager Protocol)
mechanism rather than HCI.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Brian Gix [Thu, 22 Dec 2011 00:12:12 +0000 (16:12 -0800)]
Bluetooth: Add MITM mechanism to LE-SMP
To achive Man-In-The-Middle (MITM) level security with Low Energy,
we have to enable User Passkey Comparison. This commit modifies the
hard-coded JUST-WORKS pairing mechanism to support query via the MGMT
interface of Passkey comparison and User Confirmation.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Acked-by: Marcel Holtmann<marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Ulisses Furquim [Wed, 21 Dec 2011 22:02:36 +0000 (20:02 -0200)]
Bluetooth: Fix deadlocks with sock lock and L2CAP timers locks
When cancelling a delayed work (timer) in L2CAP we can not sleep holding
the sock mutex otherwise we might deadlock with an L2CAP timer handler.
This is possible because RX/TX and L2CAP timers run in different workqueues.
The scenario below illustrates the problem. Thus we are now avoiding to
sleep on the timers locks.
======================================================
[ INFO: possible circular locking dependency detected ]
3.1.0-05270-ga978dc7-dirty #239
-------------------------------------------------------
kworker/1:1/873 is trying to acquire lock:
(sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP){+.+...}, at: [<
ffffffffa002ceac>] l2cap_chan_timeout+0x3c/0xe0 [bluetooth]
but task is already holding lock:
((&(&chan->chan_timer)->work)){+.+...}, at: [<
ffffffff81051a86>] process_one_work+0x126/0x450
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 ((&(&chan->chan_timer)->work)){+.+...}:
[<
ffffffff8106b276>] check_prevs_add+0xf6/0x170
[<
ffffffff8106b903>] validate_chain+0x613/0x790
[<
ffffffff8106dfee>] __lock_acquire+0x4be/0xac0
[<
ffffffff8106ec2d>] lock_acquire+0x8d/0xb0
[<
ffffffff81052a6f>] wait_on_work+0x4f/0x160
[<
ffffffff81052ca3>] __cancel_work_timer+0x73/0x80
[<
ffffffff81052cbd>] cancel_delayed_work_sync+0xd/0x10
[<
ffffffffa002f2ed>] l2cap_chan_connect+0x22d/0x470 [bluetooth]
[<
ffffffffa002fb51>] l2cap_sock_connect+0xb1/0x140 [bluetooth]
[<
ffffffff8130811b>] kernel_connect+0xb/0x10
[<
ffffffffa00cf98a>] rfcomm_session_create+0x12a/0x1c0 [rfcomm]
[<
ffffffffa00cfbe7>] __rfcomm_dlc_open+0x1c7/0x240 [rfcomm]
[<
ffffffffa00d07c2>] rfcomm_dlc_open+0x42/0x70 [rfcomm]
[<
ffffffffa00d3b03>] rfcomm_sock_connect+0x103/0x150 [rfcomm]
[<
ffffffff8130bd7e>] sys_connect+0xae/0xc0
[<
ffffffff813368d2>] compat_sys_socketcall+0xb2/0x220
[<
ffffffff813b2089>] sysenter_dispatch+0x7/0x30
-> #0 (sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP){+.+...}:
[<
ffffffff8106b16d>] check_prev_add+0x6cd/0x6e0
[<
ffffffff8106b276>] check_prevs_add+0xf6/0x170
[<
ffffffff8106b903>] validate_chain+0x613/0x790
[<
ffffffff8106dfee>] __lock_acquire+0x4be/0xac0
[<
ffffffff8106ec2d>] lock_acquire+0x8d/0xb0
[<
ffffffff8130d91a>] lock_sock_nested+0x8a/0xa0
[<
ffffffffa002ceac>] l2cap_chan_timeout+0x3c/0xe0 [bluetooth]
[<
ffffffff81051ae4>] process_one_work+0x184/0x450
[<
ffffffff8105276e>] worker_thread+0x15e/0x340
[<
ffffffff81057bb6>] kthread+0x96/0xa0
[<
ffffffff813b1ef4>] kernel_thread_helper+0x4/0x10
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock((&(&chan->chan_timer)->work));
lock(sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP);
lock((&(&chan->chan_timer)->work));
lock(sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP);
*** DEADLOCK ***
2 locks held by kworker/1:1/873:
#0: (events){.+.+.+}, at: [<
ffffffff81051a86>] process_one_work+0x126/0x450
#1: ((&(&chan->chan_timer)->work)){+.+...}, at: [<
ffffffff81051a86>] process_one_work+0x126/0x450
stack backtrace:
Pid: 873, comm: kworker/1:1 Not tainted
3.1.0-05270-ga978dc7-dirty #239
Call Trace:
[<
ffffffff813a0f6e>] print_circular_bug+0xd2/0xe3
[<
ffffffff8106b16d>] check_prev_add+0x6cd/0x6e0
[<
ffffffff8106b276>] check_prevs_add+0xf6/0x170
[<
ffffffff8106b903>] validate_chain+0x613/0x790
[<
ffffffff8106dfee>] __lock_acquire+0x4be/0xac0
[<
ffffffff8130d8f6>] ? lock_sock_nested+0x66/0xa0
[<
ffffffff8106ea30>] ? lock_release_nested+0x100/0x110
[<
ffffffff8130d8f6>] ? lock_sock_nested+0x66/0xa0
[<
ffffffff8106ec2d>] lock_acquire+0x8d/0xb0
[<
ffffffffa002ceac>] ? l2cap_chan_timeout+0x3c/0xe0 [bluetooth]
[<
ffffffff8130d91a>] lock_sock_nested+0x8a/0xa0
[<
ffffffffa002ceac>] ? l2cap_chan_timeout+0x3c/0xe0 [bluetooth]
[<
ffffffff81051a86>] ? process_one_work+0x126/0x450
[<
ffffffffa002ceac>] l2cap_chan_timeout+0x3c/0xe0 [bluetooth]
[<
ffffffff81051ae4>] process_one_work+0x184/0x450
[<
ffffffff81051a86>] ? process_one_work+0x126/0x450
[<
ffffffffa002ce70>] ? l2cap_security_cfm+0x4e0/0x4e0 [bluetooth]
[<
ffffffff8105276e>] worker_thread+0x15e/0x340
[<
ffffffff81052610>] ? manage_workers+0x110/0x110
[<
ffffffff81057bb6>] kthread+0x96/0xa0
[<
ffffffff813b1ef4>] kernel_thread_helper+0x4/0x10
[<
ffffffff813af69d>] ? retint_restore_args+0xe/0xe
[<
ffffffff81057b20>] ? __init_kthread_worker+0x70/0x70
[<
ffffffff813b1ef0>] ? gs_change+0xb/0xb
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Ulisses Furquim [Wed, 21 Dec 2011 12:11:33 +0000 (10:11 -0200)]
Bluetooth: Make HCI call directly into SCO and L2CAP event functions
The struct hci_proto and all related register/unregister and dispatching
code was removed. HCI core code now call directly the SCO and L2CAP
event functions.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andrei Emeltchenko [Mon, 19 Dec 2011 14:14:18 +0000 (16:14 +0200)]
Bluetooth: Remove magic numbers from le scan cmd
Make code readable by removing magic numbers.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Tue, 20 Dec 2011 19:15:56 +0000 (17:15 -0200)]
Bluetooth: fix bt_accept_dequeue() to work in process context
No local_bh_disable is needed there once we run everything in process
context. The same goes for the replacement of bh_lock_sock() by
lock_sock().
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Ulisses Furquim [Wed, 21 Dec 2011 03:32:09 +0000 (01:32 -0200)]
Bluetooth: Always compile SCO and L2CAP in Bluetooth Core
The handling of SCO audio links and the L2CAP protocol are essential to
any system with Bluetooth thus are always compiled in from now on.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Ulisses Furquim [Tue, 20 Dec 2011 19:10:51 +0000 (17:10 -0200)]
Bluetooth: Remove global mutex hci_task_lock
The hci_task_lock mutex (previously a lock) was supposed to protect the
register/unregister of HCI protocols against RX/TX tasks. This will not
be needed anymore because SCO and L2CAP will always be compiled.
Moreover, with the recent move of RX/TX to workqueues per device the
global hci_task_lock was causing starvation between different HCI
devices.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bing Zhao [Wed, 21 Dec 2011 02:19:00 +0000 (18:19 -0800)]
Bluetooth: btusb: fix bInterval for high/super speed isochronous endpoints
For high-speed/super-speed isochronous endpoints, the bInterval
value is used as exponent, 2^(bInterval-1). Luckily we have
usb_fill_int_urb() function that handles it correctly. So we just
call this function to fill in the RX URB.
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Tue, 20 Dec 2011 12:57:28 +0000 (10:57 -0200)]
Bluetooth: Rename info_work to info_timer
It makes more sense this way, since info_timer is a timer using delayed
work API.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Tue, 20 Dec 2011 12:57:27 +0000 (10:57 -0200)]
Bluetooth: convert security timer to delayed_work
This one also needs to run in process context
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Tue, 20 Dec 2011 12:57:26 +0000 (10:57 -0200)]
Bluetooth: Move l2cap_{set,clear}_timer to l2cap.h
It is the only place where it is used.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andrei Emeltchenko [Mon, 19 Dec 2011 14:31:30 +0000 (16:31 +0200)]
Bluetooth: Clean up magic pointers
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andrei Emeltchenko [Mon, 19 Dec 2011 14:31:29 +0000 (16:31 +0200)]
Bluetooth: Check for flow control mode
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andrei Emeltchenko [Mon, 19 Dec 2011 14:31:28 +0000 (16:31 +0200)]
Bluetooth: Initialize default flow control mode
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andrei Emeltchenko [Mon, 19 Dec 2011 14:31:27 +0000 (16:31 +0200)]
Bluetooth: Split ctrl init to BREDR and AMP parts
Current controller initialization is moved tp bredr_init and new
function added amp_init to handle later AMP init sequence. Current
AMP init sequence include Reset and Read Local Version.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Yogesh Ashok Powar [Fri, 16 Dec 2011 06:17:15 +0000 (11:47 +0530)]
mac80211: Fixing sparse warning at sta_info.c
The commit
42624d4913a00219a8fdbb4bafd634d1d843be85
created following sparse warning
>net/mac80211/sta_info.c:965:24: warning: incorrect type in assignment (different address spaces)
>net/mac80211/sta_info.c:965:24: expected struct tid_ampdu_tx *tid_tx
>net/mac80211/sta_info.c:965:24: got struct tid_ampdu_tx [noderef] <asn:4>*<noident>
Making use of rcu_dereference_protected to fix the problem.
V2:
- Replacing rcu_dereference with rcu_dereference_protected
as suggested by Johannes.
- Adding mutex_lock/unlock to satisfy the condition at
rcu_dereference_protected
Cc: Nishant Sarmukadam <nishants@marvell.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 19 Dec 2011 15:45:54 +0000 (16:45 +0100)]
ath9k: fix tx locking issues
The commit "ath9k: simplify tx locking" introduced a soft lockup triggered
by mac80211 sending a BAR frame triggered by a driver call to
ieee80211_tx_send_bar or ieee80211_tx_status.
Fix these issues by queueing processed tx status skbs and submitting them
to mac80211 outside of the lock.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 17 Dec 2011 15:47:56 +0000 (16:47 +0100)]
ath9k_hw: make bluetooth coexistence support optional at compile time
Many systems (e.g. embedded systems) do not have wifi modules connected to
bluetooth modules, so bluetooth coexistence is irrelevant there. With the
addition of MCI support, ath9k picked up quite a bit of extra code that
can be compiled out this way.
This patch redefines ATH9K_HW_CAP_MCI and adds an inline wrapper for
querying the bluetooth coexistence scheme, allowing the compiler to
eliminate code that uses it, with only very little use of #ifdef.
On MIPS this reduces the total size for the modules by about 20k.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sat, 17 Dec 2011 12:57:27 +0000 (13:57 +0100)]
b43: N-PHY: reorder functions: random cleanups
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sat, 17 Dec 2011 12:57:26 +0000 (13:57 +0100)]
b43: N-PHY: reorder functions: move rest of workarounds
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sat, 17 Dec 2011 12:57:25 +0000 (13:57 +0100)]
b43: N-PHY: reorder functions: move RSSI calibration
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sat, 17 Dec 2011 12:57:24 +0000 (13:57 +0100)]
b43: N-PHY: split gain control workarounds
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sat, 17 Dec 2011 12:57:23 +0000 (13:57 +0100)]
b43: N-PHY: reorder functions: collect RSSI selects
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sat, 17 Dec 2011 12:57:22 +0000 (13:57 +0100)]
b43: N-PHY: reorder functions: collect samples ones
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sat, 17 Dec 2011 12:57:21 +0000 (13:57 +0100)]
b43: N-PHY: reorder functions: collect radio ones
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sat, 17 Dec 2011 12:57:20 +0000 (13:57 +0100)]
b43: N-PHY: reorder functions: put basic ones at beginning
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sat, 17 Dec 2011 03:17:16 +0000 (21:17 -0600)]
rtlwifi: Fix locking problem introduces with commit
6539306b
When I tested commit
6539306, I did not notice that loading an out-of-tree
module turns off lockdep testing in kernel 3.2. For that reason, I missed
the kernel WARNING shown below:
The solution fixes the warning by partially reverting commit
6539306.
[ 84.168146] ------------[ cut here ]------------
[ 84.168155] WARNING: at kernel/mutex.c:198 mutex_lock_nested+0x309/0x310()
[ 84.168158] Hardware name: HP Pavilion dv2700 Notebook PC
[ 84.168161] Modules linked in: nfs lockd auth_rpcgss nfs_acl sunrpc af_packet cpufreq_conservative cpufreq_userspace cpufreq_powersave powernow_k8 mperf e
xt3 jbd ide_cd_mod cdrom snd_hda_codec_conexant arc4 rtl8192ce ide_pci_generic rtl8192c_common rtlwifi snd_hda_intel mac80211 snd_hda_codec snd_pcm snd_timer
amd74xx ide_core cfg80211 k8temp snd joydev soundcore hwmon battery forcedeth i2c_nforce2 sg rfkill ac serio_raw snd_page_alloc button video i2c_core ipv6 a
utofs4 ext4 mbcache jbd2 crc16 sd_mod ahci ohci_hcd libahci libata scsi_mod ehci_hcd usbcore usb_common fan processor thermal
[ 84.168231] Pid: 1218, comm: kworker/u:2 Not tainted 3.2.0-rc5-wl+ #155
[ 84.168234] Call Trace:
[ 84.168240] [<
ffffffff81048aaa>] warn_slowpath_common+0x7a/0xb0
[ 84.168245] [<
ffffffff81048af5>] warn_slowpath_null+0x15/0x20
[ 84.168249] [<
ffffffff813811f9>] mutex_lock_nested+0x309/0x310
[ 84.168269] [<
ffffffffa00793f9>] ? rtl_ips_nic_on+0x49/0xb0 [rtlwifi]
[ 84.168277] [<
ffffffffa00793f9>] rtl_ips_nic_on+0x49/0xb0 [rtlwifi]
[ 84.168284] [<
ffffffffa007ab85>] rtl_pci_tx+0x1b5/0x560 [rtlwifi]
[ 84.168291] [<
ffffffffa007635a>] rtl_op_tx+0x9a/0xa0 [rtlwifi]
[ 84.168359] [<
ffffffffa043cf51>] __ieee80211_tx+0x181/0x2b0 [mac80211]
[ 84.168375] [<
ffffffffa043ef06>] ieee80211_tx+0xf6/0x120 [mac80211]
[ 84.168391] [<
ffffffffa043ee49>] ? ieee80211_tx+0x39/0x120 [mac80211]
[ 84.168408] [<
ffffffffa043f80b>] ieee80211_xmit+0xdb/0x100 [mac80211]
[ 84.168425] [<
ffffffffa043f730>] ? ieee80211_skb_resize.isra.26+0xb0/0xb0 [mac80211]
[ 84.168441] [<
ffffffffa0440b2a>] ieee80211_tx_skb_tid+0x5a/0x70 [mac80211]
[ 84.168458] [<
ffffffffa0443da2>] ieee80211_send_auth+0x152/0x1b0 [mac80211]
[ 84.168474] [<
ffffffffa042e169>] ieee80211_work_work+0x1049/0x1860 [mac80211]
[ 84.168489] [<
ffffffffa042d120>] ? free_work+0x20/0x20 [mac80211]
[ 84.168504] [<
ffffffffa042d120>] ? free_work+0x20/0x20 [mac80211]
[ 84.168510] [<
ffffffff81065ffc>] process_one_work+0x17c/0x530
[ 84.168514] [<
ffffffff81065f92>] ? process_one_work+0x112/0x530
[ 84.168519] [<
ffffffff81066994>] worker_thread+0x164/0x350
[ 84.168524] [<
ffffffff8108420d>] ? trace_hardirqs_on+0xd/0x10
[ 84.168528] [<
ffffffff81066830>] ? manage_workers.isra.28+0x220/0x220
[ 84.168533] [<
ffffffff8106bc17>] kthread+0x87/0x90
[ 84.168539] [<
ffffffff813854b4>] kernel_thread_helper+0x4/0x10
[ 84.168543] [<
ffffffff81382bdd>] ? retint_restore_args+0xe/0xe
[ 84.168547] [<
ffffffff8106bb90>] ? __init_kthread_worker+0x70/0x70
[ 84.168552] [<
ffffffff813854b0>] ? gs_change+0xb/0xb
[ 84.168554] ---[ end trace
f25a4fdc768c028f ]---
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stanislaw Gruska <sgruszka@redhat.com>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:20 +0000 (18:37 -0800)]
brcm80211: fmac: add Kconfig option for SDIO bus support
This patch adds a Kconfig option for SDIO bus support and abstracts
a build subset correspondingly. It's the final patch of fullmac bus
interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:19 +0000 (18:37 -0800)]
brcm80211: fmac: exclude unnecessary header files
This patch removes some headers files include lines from sdio layer
code. This is part of the fullmac bus interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:18 +0000 (18:37 -0800)]
brcm80211: fmac: move idle macros to dhd_sdio.c
The idle macros are only used by dhd_sdio.c. It's more appropriate
to place them in dhd_sdio.c instead of dhd.h.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:17 +0000 (18:37 -0800)]
brcm80211: fmac: move debug level macros to dhd_dbg.h
Debug message level macros are used for debug purpose. It would be
more appropriate to place them at dhd_dbg.h.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:16 +0000 (18:37 -0800)]
brcm80211: fmac: abstract ctrl frames interface function pointers
Abstract bus layer brcmf_bus_txctl/brcmf_bus_rxctl function
pointers for common layer. This patch is part of the fullmac bus
interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:15 +0000 (18:37 -0800)]
brcm80211: fmac: abstract bus_txdata interface function pointer
Abstract bus layer brcmf_bus_txdata function pointer for common
layer. This patch is part of the fullmac bus interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:14 +0000 (18:37 -0800)]
brcm80211: fmac: abstract bus_init interface function pointer
Abstract bus layer brcmf_bus_init function pointer for common
layer. This patch is part of the fullmac bus interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:13 +0000 (18:37 -0800)]
brcm80211: fmac: move common layer bus interface context to dhd_bus.h
dhd_bus.h is the header file for bus interface. Move functions
declarations and brcmf_bus structure to there. This is part of
the fullmac bus interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:12 +0000 (18:37 -0800)]
brcm80211: fmac: abstract bus_stop interface function pointer
Common layer should use interface function pointer stored in
brcmf_bus to invoke corresponding interface function in bus layer.
This patch is part of the fullmac bus interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:11 +0000 (18:37 -0800)]
brcm80211: fmac: move sdio related macros to sdio_host.h
dhd_bus.h will be used as the shared header file for common layer
and bus layer. It should not contain any sdio specific macros.
This patch moves them to sdio_host.h as part of the fullmac bus
interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:10 +0000 (18:37 -0800)]
brcm80211: fmac: stop referencing brcmf_sdio in common layer
brcmf_sdio is the data structure for sdio bus layer. Stop
referencing brcmf_sdio from common layer. This patch is part of
the fullmac bus interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:09 +0000 (18:37 -0800)]
brcm80211: fmac: stop referencing brcmf_pub in bus layer
brcmf_pub is the data structure for common layer. Since brcmf_bus
should be the only structure shared by common layer and bus layer,
stop referencing brcmf_pub from bus layer. This patch is part of
the fullmac bus interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:08 +0000 (18:37 -0800)]
brcm80211: fmac: move tx flow ctrl flag to bus layer
txoff is the flow control flag for transmit used in sdio layer.
Move it to bus layer data structure brcmf_sdio. Also flag
management code is moved out of brcmf_txflowcontrol(). This is
part of the fullmac bus interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:07 +0000 (18:37 -0800)]
brcm80211: fmac: move packet realloc stats to struct brcmf_bus
tx_realloc is used by both common layer and bus layer. This patch
moves it to interface structure brcmf_bus as part of the fullmac
bus interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:06 +0000 (18:37 -0800)]
brcm80211: fmac: move dongle statistics to struct brcmf_bus
Dongle statistics are shared data between common layer and bus
layer. This patch places them in bus interface structure brcmf_bus
as part of the fullmac bus interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:05 +0000 (18:37 -0800)]
brcm80211: fmac: remove duplicate statistics from driver data structure
Some dongle statistics are stored in two places and synced when net
device status inquired. There is no need to do it this way any more.
Direct all usage to dongle stats structure in order to increase
readability.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:04 +0000 (18:37 -0800)]
brcm80211: fmac: move driver up status to struct brcmf_bus
Driver up/down status to network interface need to be shared by
common layer and bus layer. Move it to bus interface structure
brcmf_bus as part of the fullmac bus interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:03 +0000 (18:37 -0800)]
brcm80211: fmac: move maxctl to struct brcmf_bus
maxctl is the max size of rxctl request from protocol layer to bus
layer. Move it to bus interface structure brcmf_bus. This is part
of the fullmac bus interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:02 +0000 (18:37 -0800)]
brcm80211: fmac: move sdio used statistics to struct brcmf_sdio
Some statistics only used by sdio modules. Move them to sdio layer
private structure brcmf_sdio. This is part of the fullmac bus
interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:01 +0000 (18:37 -0800)]
brcm80211: fmac: change function proto_hdrpull parameter
Change parameter to device pointer for bus layer interface function
brcmf_proto_hdrpull This is part of the fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:37:00 +0000 (18:37 -0800)]
brcm80211: fmac: change function rx_frame parameter
Change parameter to device pointer for bus layer interface function
brcmf_rx_frame. This is part of the fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:36:59 +0000 (18:36 -0800)]
brcm80211: fmac: change function brcmf_c_prec_enq parameter
Change parameter to device pointer for bus layer interface function
brcmf_c_prec_enq. This is part of the fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:36:58 +0000 (18:36 -0800)]
brcm80211: fmac: change function txcomplete parameter
Change parameter to device pointer for bus layer interface function
brcmf_txcomplete. This is part of the fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:36:57 +0000 (18:36 -0800)]
brcm80211: fmac: change function txflowcontrol parameter
Change parameter to device pointer for bus layer interface function
brcmf_txflowcontrol. This is part of the fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:36:56 +0000 (18:36 -0800)]
brcm80211: fmac: change function brcmf_detach parameter
Change parameter to device pointer for bus layer interface function
brcmf_detach. This is part of the fullmac bus interface refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:36:55 +0000 (18:36 -0800)]
brcm80211: fmac: change function bus_start parameter
Change parameter to device pointer for bus layer interface function
brcmf_bus_start. This is part of the fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:36:54 +0000 (18:36 -0800)]
brcm80211: fmac: change function add_if parameter
Change parameter to device pointer for bus layer interface function
brcmf_add_if. This is part of the fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:36:53 +0000 (18:36 -0800)]
brcm80211: fmac: register a dummy irq handler for SDIO function 2
When there is data available in dongle for driver to fetch, an
interrupt will be triggered and both SDIO function 1 and 2 will be
flagged by default in bcm4329. These two interrupt flags are
identical and only need to be handled once. Since there is no way
to turn off one flag from the dongle side, a dummy handler for
function 2 interrupt is placed.
Reported-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:36:52 +0000 (18:36 -0800)]
brcm80211: fmac: remove oneline proto block functions
brcmf_os_proto_block and brcmf_os_proto_unblock are oneline
functions handling proto_block mutex. Place the mutex interface
call inline to increase readability.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 17 Dec 2011 02:36:51 +0000 (18:36 -0800)]
brcm80211: fmac: unify common layer driver data structure
No need to split data structure for common layer into brcmf_pub and
brcmf_info. Absorb brcmf_info into brcmf_pub to increase code
readability.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Fri, 16 Dec 2011 20:26:00 +0000 (23:26 +0300)]
NFC: use kfree_skb() for sk_buffs
This is a struct sk_buff pointer and it should be freed with kfree_skb()
instead of kfree().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Fri, 16 Dec 2011 20:25:29 +0000 (23:25 +0300)]
NFC: double unlock in nfc_llcp_recv_connect()
We unlock inside the if block on the other side of this if else
statement. It could result in calling mutex_unlock() twice.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
francesco.gringoli@ing.unibs.it [Fri, 16 Dec 2011 17:34:56 +0000 (18:34 +0100)]
b43: avoid packet losses in the dma worker code.
Following Rafal request, we verified that on "modern" CPUs using one
or more workers is equivalent. Here is patch V3 that addresses the
packet loss bug in the dma engine using only one worker.
-------
This patch addresses a bug in the dma worker code that keeps draining
packets even when the hardware queues are full. In such cases packets
can not be passed down to the device and are erroneusly dropped by the
code.
This problem was already discussed here
http://www.mail-archive.com/b43-dev@lists.infradead.org/msg01413.html
and acknowledged by Michael.
Number of hardware queues is now defined in b43.h (B43_QOS_QUEUE_NUM).
Acknowledgements to Riccardo Paolillo <riccardo.paolillo@gmail.com> and
Michele Orru <michele.orru@hotmail.it>
Signed-off-by: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 16 Dec 2011 14:28:57 +0000 (15:28 +0100)]
mac80211: handle SMPS action frames
When a peer changes SMPS state we should update
rate control so it doesn't have to detect it by
itself. It can't detect "dynamic" mode anyway
since that just requires rts-cts handshaking.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz [Fri, 16 Dec 2011 14:03:36 +0000 (15:03 +0100)]
NFC: Fix LLCP related build failure
llcp_mac routines should be static and inlined or build will fail with NFC
selected without LLCP.
This patch fixes:
LD [M] net/nfc/nfc.o
net/nfc/netlink.o: In function `nfc_llcp_mac_is_down':
netlink.c:(.text+0x0): multiple definition of `nfc_llcp_mac_is_down'
net/nfc/core.o:(.text+0x0): first defined here
net/nfc/netlink.o: In function `nfc_llcp_mac_is_up':
netlink.c:(.text+0x10): multiple definition of `nfc_llcp_mac_is_up'
net/nfc/core.o:(.text+0x10): first defined here
net/nfc/af_nfc.o: In function `nfc_llcp_mac_is_down':
(.text+0x0): multiple definition of `nfc_llcp_mac_is_down'
net/nfc/core.o:(.text+0x0): first defined here
net/nfc/af_nfc.o: In function `nfc_llcp_mac_is_up':
(.text+0x10): multiple definition of `nfc_llcp_mac_is_up'
net/nfc/core.o:(.text+0x10): first defined here
net/nfc/rawsock.o: In function `nfc_llcp_mac_is_down':
rawsock.c:(.text+0x0): multiple definition of `nfc_llcp_mac_is_down'
net/nfc/core.o:(.text+0x0): first defined here
net/nfc/rawsock.o: In function `nfc_llcp_mac_is_up':
rawsock.c:(.text+0x10): multiple definition of `nfc_llcp_mac_is_up'
net/nfc/core.o:(.text+0x10): first defined here
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Fri, 16 Dec 2011 05:00:37 +0000 (21:00 -0800)]
mwifiex: cleanup work in scan.c
Scan type derived from IEEE80211_CHAN_PASSIVE_SCAN bit is a boolean
flag representing passive scanning. We should not again compare it
with driver specific macro MWIFIEX_SCAN_TYPE_PASSIVE to determine
passive or active scan. We can also avoid the use of local variable
by using the flag directly.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 15 Dec 2011 22:55:53 +0000 (14:55 -0800)]
ath: Convert ath_dbg(bar, ATH_DBG_<FOO>, to ath_dbg(bar, FOO
Add ATH_DBG_ to macros to shorten the uses and
reduce the line count.
Coalesce ath_dbg formats.
Add missing spaces to coalesced formats.
Add missing newline terminations to ath_dbg formats.
Align ath_dbg arguments where appropriate.
Standardize ath_dbg formats without periods.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Paul Stewart [Fri, 9 Dec 2011 19:01:49 +0000 (11:01 -0800)]
cfg80211: Return beacon loss count in station
If station info contains a beacon loss count, return
it to userspace.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nikolay Martynov [Sun, 18 Dec 2011 00:39:35 +0000 (19:39 -0500)]
mac80211: split addba retries in time
Currently code allows three (HT_AGG_MAX_RETRIES) unanswered addba
requests. When this limit is reached aggregation is turned off for
given TID permanently. This doesn't seem right: three requests is
not that much, some 'blackout' can happen, but effect of it affects
whole connection indefinitely.
This patch increases number of retries to 15. Also, when there have
been 3 or more retries it splits further retries apart by 15 seconds
instead of sending them in very short period of time.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 19 Dec 2011 19:28:22 +0000 (14:28 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/padovan/bluetooth-next
John W. Linville [Mon, 19 Dec 2011 19:25:17 +0000 (14:25 -0500)]
Merge branch 'for-linville' of git://github.com/kvalo/ath6kl
John W. Linville [Mon, 19 Dec 2011 19:24:13 +0000 (14:24 -0500)]
Merge branch 'wireless-next' of git://git./linux/kernel/git/iwlwifi/iwlwifi
Gustavo F. Padovan [Mon, 19 Dec 2011 13:37:53 +0000 (11:37 -0200)]
Merge git://git./linux/kernel/git/padovan/bluetooth
Conflicts:
net/bluetooth/l2cap_core.c
Johan Hedberg [Mon, 19 Dec 2011 12:29:08 +0000 (14:29 +0200)]
Bluetooth: Add missing mgmt_confirm_name command definition
This patch adds the necessary structs for the Confirm Name command. This
ensures that the protocol definitions are up to date with the latest
mgmt specification. The actual implementation of the command will follow
in a later patch-set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Mon, 19 Dec 2011 12:29:07 +0000 (14:29 +0200)]
Bluetooth: Fix mgmt_(block,unblock)_device opcodes
This patch fixes the opcodes of the Block/Unblock device commands to
match with what user-space expects and to confirm with the latest mgmt
specification. The reason the values were wrong was a missing Confirm
Name command definition (which will be added by a subsequent patch).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Mon, 19 Dec 2011 12:29:06 +0000 (14:29 +0200)]
Bluetooth: Add missing confirm_name field to mgmt_ev_device_found
This patch adds a missing confirm_name field to mgmt_ev_device_found.
Support for setting the correct value for this field is not implemented
yet, but having it part of the struct definition ensures that user-space
gets correct sized device_found events and is thereby able to do at
least rudimentary parsing of them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Mon, 19 Dec 2011 00:33:30 +0000 (22:33 -0200)]
Revert "Bluetooth: Revert: Fix L2CAP connection establishment"
This reverts commit
4dff523a913197e3314c7b0d08734ab037709093.
It was reported that this patch cause issues when trying to connect to
legacy devices so reverting it.
Reported-by: David Fries <david@fries.net>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Mat Martineau [Wed, 7 Dec 2011 00:23:26 +0000 (16:23 -0800)]
Bluetooth: Clear RFCOMM session timer when disconnecting last channel
When the last RFCOMM data channel is closed, a timer is normally set
up to disconnect the control channel at a later time. If the control
channel disconnect command is sent with the timer pending, the timer
needs to be cancelled.
If the timer is not cancelled in this situation, the reference
counting logic for the RFCOMM session does not work correctly when the
remote device closes the L2CAP connection. The session is freed at
the wrong time, leading to a kernel panic.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Mat Martineau [Fri, 9 Dec 2011 01:23:21 +0000 (17:23 -0800)]
Bluetooth: Prevent uninitialized data access in L2CAP configuration
When configuring an ERTM or streaming mode connection, remote devices
are expected to send an RFC option in a successful config response. A
misbehaving remote device might not send an RFC option, and the L2CAP
code should not access uninitialized data in this case.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Mat Martineau [Tue, 13 Dec 2011 23:06:02 +0000 (15:06 -0800)]
Bluetooth: Incoming ACL packets do not force active mode
Incoming sk_buffs always have bt_cb(skb)->force_active set to 0, so
it's misleading to use that value from the control block when calling
hci_conn_enter_active_mode() for incoming data. The destination socket
is not known in the HCI layer, so the force_active setting for each
socket isn't known either. Hard-coding the force_active parameter does
not change any behavior, but makes it obvious that incoming ACL data
never exits sniff mode.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andrei Emeltchenko [Wed, 7 Dec 2011 13:56:52 +0000 (15:56 +0200)]
Bluetooth: Simplify num_comp_pkts_evt function
Simplify function and remove fourth level of indentation.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andrei Emeltchenko [Wed, 7 Dec 2011 13:56:51 +0000 (15:56 +0200)]
Bluetooth: Add HCI Read Data Block Size function
Implement block size read function. Use different variables for
packet-based and block-based flow control.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Wed, 14 Dec 2011 22:47:41 +0000 (00:47 +0200)]
Bluetooth: Use correct struct for user_confirm_neg_reply
This patch fixes user_confirm_neg_reply to use the appropriate struct
for accessing the call parameters.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Wed, 14 Dec 2011 22:47:40 +0000 (00:47 +0200)]
Bluetooth: Update ordering and opcodes of mgmt messages
This patch updates the ordering and opcodes of mgmt messages to match
the latest API specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Wed, 14 Dec 2011 22:47:39 +0000 (00:47 +0200)]
Bluetooth: Add timer for automatically disabling the service cache
We do not want the service cache to be enabled indefinitely after
mgmt_read_info is called. To solve this a timer is added which will
automatically disable the cache if mgmt_set_dev_class isn't called
within 5 seconds of calling mgmt_read_info.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Wed, 14 Dec 2011 22:47:38 +0000 (00:47 +0200)]
Bluetooth: Move EIR and CoD update functions to a better position
Due to the upcoming addition of a service cache timer the functions to
update the EIR and CoD need to be higher up in mgmt.c in order to avoid
unnecessary forward-declarations. This patch simply moves code around
without any other changes in order to make subsequent patches more
readable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Wed, 14 Dec 2011 22:47:37 +0000 (00:47 +0200)]
Bluetooth: Remove mgmt_set_service_cache
Instead of having an explicit service cache command we can make the mgmt
API simpler by implicitly enabling the cache when mgmt_read_info is
called for the first time and disabling it when mgmt_set_dev_class is
called.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Wed, 14 Dec 2011 22:47:36 +0000 (00:47 +0200)]
Bluetooth: Move mgmt_set_fast_connectable to the right location
Fast connectable is logically after the connectable property so that's
where it should show up in the code as well (it's also after connectable
in the settings bitfield).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Wed, 14 Dec 2011 22:47:35 +0000 (00:47 +0200)]
Bluetooth: Update mgmt_read_info and related mgmt messages
This patch updates the mgmt_read_info and related messages to the latest
management API which uses a bitfield of settings instead of individual
boolean values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Sun, 18 Dec 2011 15:39:33 +0000 (13:39 -0200)]
Bluetooth: Add ProFUSION's copyright
Add ProFUSION's copyright to some files I've been touching recently.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Sun, 18 Dec 2011 14:40:32 +0000 (12:40 -0200)]
Bluetooth: Use system workqueue to schedule power_on
hdev->workqueue should be only for rx/tx, so move this one out.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Sat, 17 Dec 2011 20:53:02 +0000 (18:53 -0200)]
Bluetooth: Remove work_add and work_del from hci_sysfs
As we run in process context now we don't need worqueue to add e del from
sysfs.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Sat, 17 Dec 2011 19:47:30 +0000 (17:47 -0200)]
Bluetooth: Use new alloc_workqueue()
Update hdev workqueue API usage to use the new interface, this new
interface also allow us to mark this workqueue as WQ_HIGHPRI, so now rx
and tx work gets higher priority when running.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Sat, 17 Dec 2011 16:52:27 +0000 (14:52 -0200)]
Bluetooth: move power_off to system workqueue
hdev->workqueue will be only for for rx/tx/cmd processing, all other small
works should go to the system workqueue for now.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Sat, 17 Dec 2011 12:56:45 +0000 (10:56 -0200)]
Bluetooth: Change l2cap chan_list to use RCU
This list has much more reads than writes, so RCU makes senses here, also
it avoid deadlock against the socket lock.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Fri, 9 Dec 2011 06:48:17 +0000 (04:48 -0200)]
Bluetooth: invert locking order in connect path
This move some checking code that was in l2cap_sock_connect() to
l2cap_chan_connect(). Thus we can invert the lock calls, i.e., call
lock_sock() before hci_dev_lock() to avoid a deadlock scenario.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Thu, 15 Dec 2011 03:16:14 +0000 (01:16 -0200)]
Bluetooth: convert info timer to delayed_work
Another step of remove interrupt context from Bluetooth Core.
Use the system workqueue.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Thu, 15 Dec 2011 02:50:02 +0000 (00:50 -0200)]
Bluetooth: convert tx_task to workqueue
This should simplify Bluetooth core processing a lot.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Thu, 15 Dec 2011 01:53:47 +0000 (23:53 -0200)]
Bluetooth: Move command task to workqueue
As part of the moving on all the Bluetooth processing to Process context.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Thu, 15 Dec 2011 00:58:44 +0000 (22:58 -0200)]
Bluetooth: Don't disable tasklets to call hdev->notify()
It's pointless, we aren't protecting anything since btusb_notify()
schedules a work to run, then all it operation happens without protection.
If protection is really needed here, we will fix it further.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Thu, 15 Dec 2011 00:54:12 +0000 (22:54 -0200)]
Bluetooth: convert conn hash to RCU
Handling hci_conn_hash with RCU make us avoid some locking and disable
tasklets.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>