OSDN Git Service
Fabio Estevam [Sat, 3 Mar 2018 22:40:40 +0000 (19:40 -0300)]
ARM: dts: vf500: Remove skeleton.dtsi inclusion
Since commit
9c0da3cc61f1 ("ARM: dts: explicitly mark skeleton.dtsi as
deprecated") the inclusion of skeleton.dtsi is deprecated, so
remove it as this file will eventually go away someday.
Move its content to the SoC dtsi file, so that the resultant dtb
is the same.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Fri, 2 Mar 2018 01:59:29 +0000 (09:59 +0800)]
ARM: dts: imx7s: add temperature monitor support
Add i.MX7 temperature monitor support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rob Herring [Thu, 1 Mar 2018 20:25:33 +0000 (14:25 -0600)]
ARM: dts: imx: Add missing #sound-dai-cells for sgtl5000 codec
dtc now warns about missing #sound-dai-cells:
arch/arm/boot/dts/imx6ul-geam.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@
2100000/i2c@
21a0000/codec@a or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/imx6ul-isiot-emmc.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@
2100000/i2c@
21a0000/codec@a or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/imx6ul-isiot-nand.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@
2100000/i2c@
21a0000/codec@a or bad phandle (referred from sound-dai[0])
Lots of i.MX boards use the SGTL5000 codec, but not all get the warning
because only some reference the codec with "sound-dai" property. However,
the codec should always provide #sound-dai-cells regardless, so fix all
the occurrences.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Thu, 1 Mar 2018 19:20:07 +0000 (11:20 -0800)]
ARM: dts: imx51-zii-rdu1: Add node for RAVE SP device
With MFD and watchdog drivers for RAVE SP device support added by
538ee27290fa ("mfd: Add driver for RAVE Supervisory Processor") and
c3bb33345721 ("watchdog: Add RAVE SP watchdog driver") add
corresponding DT node for RDU.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Chris Healy <cphealy@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Thu, 1 Mar 2018 19:20:06 +0000 (11:20 -0800)]
ARM: dts: imx6: RDU2: Add RAVE SP device
With MFD and watchdog drivers for RAVE SP device support added by
538ee27290fa ("mfd: Add driver for RAVE Supervisory Processor") and
c3bb33345721 ("watchdog: Add RAVE SP watchdog driver") add
corresponding DT node for RDU2.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Chris Healy <cphealy@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 28 Feb 2018 02:13:35 +0000 (23:13 -0300)]
ARM: dts: imx5: Pass the memory unit-address
Pass the memory unit-address to fix the following build warnings with W=1:
arch/arm/boot/dts/imx51-zii-rdu1.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx53-tx53-x03x.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx53-tx53-x13x.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
In theses cases an empty memory node is passed, which will be filled
by the bootloader. Passing the memory base address still allows the
bootloader to fill the memory size.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Tue, 27 Feb 2018 16:30:49 +0000 (17:30 +0100)]
ARM: dts: imx7s: add spba-bus abstraction
According to the i.MX 7Solo/Dual Application Processor Reference
Manual the ECSPI1/2/3, UART1/2/3 and SAI1/2/3 peripherals are
connected through the SPBA bus. Other similar SoCs such as i.MX 6UL
add this bus abstraction. This adds the bus also to the i.MX 7
device tree.
The i.MX SDMA driver uses this abstraction to configure watermark
levels slightly differently, so this might change behavior slightly.
There have no issues been observed before or after the patch.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Shyam Saini [Tue, 27 Feb 2018 15:59:03 +0000 (21:29 +0530)]
ARM: dts: imx6dl-icore-rqs: Fix invalid PHY address assignment for ethernet
Add "reg" property for ethernet to fix this issue.
Errors in boot logs:
mdio_bus
2188000.ethernet-1:
/soc/aips-bus@
02100000/ethernet@
02188000/mdio/ethernet-phy
has invalid PHY address
mdio_bus
2188000.ethernet-1: scan phy ethernet-phy at address 0
mdio_bus
2188000.ethernet-1: scan phy ethernet-phy at address 1
mdio_bus
2188000.ethernet-1: scan phy ethernet-phy at address 2
mdio_bus
2188000.ethernet-1: scan phy ethernet-phy at address 3
Reported-by: Shyam Saini <shyam@amarulasolutions.com>
Suggested-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Shyam Saini <shyam@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jörg Krause [Sun, 25 Feb 2018 01:24:46 +0000 (02:24 +0100)]
ARM: dts: imx6ul: add wdog3 node
The i.MX6UL(L) has a WDOG3 located at start address 0x021E0000 in the
AIPS-2 memory region [1].
[1] i.MX 6UltraLite Applications Processor Reference Manual, Rev. 1,
04/2016, Table-2-3 AIPS-2 memory map, p. 166
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Tue, 27 Feb 2018 15:16:10 +0000 (16:16 +0100)]
ARM: dts: imx7: add CPU PMU support
Enable support for ARM Performance Monitoring Units available
on the Cortex-A7 CPU. There is only a single interrupt for the
PMU in both variants of the family, i.MX 7Solo and 7Dual.
Tested with perf on a i.MX 7Dual:
hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Tue, 27 Feb 2018 08:00:23 +0000 (09:00 +0100)]
ARM: dts: imx6dl-colibri-eval-v3: Add chosen node
Add Colibri UART_A as default serial console.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Thu, 22 Feb 2018 17:16:35 +0000 (14:16 -0300)]
ARM: dts: imx6: Pass memory unit-adress
Pass the memory unit-adress to fix the following build warnings with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
There are cases where dts passes an empty memory node, which will be filled
by the bootloader. Passing the memory base address still allows the
bootloader to fill the memory size.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lothar Waßmann [Mon, 19 Feb 2018 10:47:05 +0000 (11:47 +0100)]
ARM: dts: imx6dl: remove 'lcdif' node
According to the "i.MX 6Solo/6DualLite Applications Processor
Reference Manual" Rev. 3, 09/2017 there is no LCDIF unit on the
i.MX6DL.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Baruch Siach [Mon, 19 Feb 2018 07:56:45 +0000 (09:56 +0200)]
ARM: dts: hummingboard: Remove mention of nonexistent node
There is no pinctrl_usbotg_2 node in current Hummingboard dts files.
Drop reference to that.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jon Nettleton [Mon, 19 Feb 2018 07:56:44 +0000 (09:56 +0200)]
ARM: dts: imx6qdl-hummingboard: fix USBOTG-ID pin
Fix the USBOTG-ID pin to the correct definition. The top
USB port stays in device-mode without this change.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Sat, 17 Feb 2018 15:41:43 +0000 (13:41 -0200)]
ARM: dts: imx28-tx28: Pass the memory unit name
Pass the memory unit name in order to fix the following
dtc warning with W=1:
arch/arm/boot/dts/imx28-tx28.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lucas Stach [Mon, 12 Feb 2018 15:57:52 +0000 (16:57 +0100)]
ARM: dts: imx6: remove GPU subsystem nodes
They aren't needed by the etnaviv driver anymore and have been removed
from the binding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lucas Stach [Mon, 12 Feb 2018 13:08:18 +0000 (14:08 +0100)]
ARM: dts: imx6: RDU2: detail USDHC description
None of the slots support 1.8V signaling or SDIO. There is no point in
probing for a SD card on the eMMC controller.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ken Lin [Fri, 9 Feb 2018 21:55:15 +0000 (05:55 +0800)]
ARM: dts: imx: Add support for Advantech DMS-BA16
Add support for Advantech DMS-BA16 board, which uses
the Advantech BA-16 module.
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Tue, 6 Feb 2018 16:49:03 +0000 (17:49 +0100)]
ARM: dts: imx6ull: add Toradex Colibri iMX6ULL support
Add support for the Computer on Module Colibri iMX6ULL and its
Bluetooth/Wifi variant along with the development/evaluation carrier
board device trees. Follow the usual hierarchic include model,
maintaining shared configuration in imx6ull-colibri.dtsi and
imx6ull-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jörg Krause [Mon, 5 Feb 2018 20:47:59 +0000 (21:47 +0100)]
ARM: dts: imx6ul: rename mux mode name REF_CLK_32K to OSC32K_32K_OUT
This is a rebased version of patch [0].
The 32 kHz reference clock on the i.MX6UL(L) can be output by
setting the external signal XTALOSC_REF_CLK_32K in one of the
following ways [1]:
|----------------------------------------------------------|
| Signal | Pad | Mode | Direction |
|----------------------------------------------------------|
| XTALOSC_REF_CLK_32K | ENET1_RX_EN | ALT2 | O |
| | GPIO1_IO03 | ALT3 | |
| | JTAG_TCK | ALT6 | |
|----------------------------------------------------------|
Before patch [2] the mux mode for the external reference clock was
missing. The patch named the mux mode as used in the NXP Linux
4.9.11_1.0.0 release, but the Reference Manual uses the name
OSC32K_32K_OUT, e.g. in [3].
As Philipp and Shawn suggest the name from the RM should be used
instead.
[0] https://patchwork.kernel.org/patch/
10172187/
[1] IMX6ULRM, Rev. 1, 04/2016, Table 58-1, p. 3649
[2] https://patchwork.kernel.org/patch/
10156121/
[3] IMX6ULRM, Rev. 1, 04/2016, 30.5.47 SW_MUX_CTL_PAD_ENET1_RX_EN SW MUX
Control Register (IOMUXC_SW_MUX_CTL_PAD_ENET1_RX_EN), p. 1357
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lothar Waßmann [Thu, 8 Feb 2018 07:07:37 +0000 (15:07 +0800)]
ARM: dts: imx6ull: fix the imx6ull-14x14-evk configuration
imx6ull-14x14-evk.dts currently includes the imx6ul.dtsi file for an
i.MX6ULL SoC which is plain wrong.
Rename the current imx6ul-14x14-evk.dts to .dtsi and include it from
imx6ul-14x14-evk.dts and imx6ull-14x14-evk.dts, so that both can
include the appropriate SoC specific (imx6ul.dtsi/imx6ull.dtsi) file.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Peter Senna Tschudin [Mon, 5 Feb 2018 17:08:40 +0000 (18:08 +0100)]
ARM: dts: imx6q-bx50v3: Enable secure-reg-access
Enable secure debug enable register access for Bx50v3 devices to enable
PMU and hardware counters for perf.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Fri, 2 Feb 2018 23:26:39 +0000 (21:26 -0200)]
ARM: dts: imx27-eukrea-cpuimx27: Put the clock node directly into root
Put the UART clock node directly under root with a unique node name and
drop unit-address in order to fix the following build warning with W=1:
arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dtb: Warning (simple_bus_reg): Node /clocks/osc26m missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Aapo Vienamo [Wed, 31 Jan 2018 14:34:07 +0000 (14:34 +0000)]
ARM: dts: imx7d: cl-som-imx7: fix pinctrl_enet
The missing last digit of the CONFIG values is added. Looks like a typo
of some sort when comparing to the downstream dt. This fixes
intermittent behavior behaviour of the ethernet controllers.
Signed-off-by: Aapo Vienamo <aapo@tuxera.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Benoît Thébaudeau [Wed, 31 Jan 2018 21:35:44 +0000 (22:35 +0100)]
ARM: dts: imx25-pinfunc: Always set SION for eSDHC CMD
The eSDHC does not work properly if the SION bit is not set for the
bidirectional CMD signal, whatever the eSDHC instance and the selected
pad. Therefore, setting SION is mandatory for all eSDHC CMD ports. Do
this for MX25_PAD_*__ESDHCn_CMD in imx25-pinfunc.h in order to enforce
this behavior for all boards.
This had already been done for eSDHC1, but not for eSDHC2. Also, define
MX25_PAD_FEC_MDC__ESDHC2_CMD so that all the possible cases are covered
from now on.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Benoît Thébaudeau [Wed, 31 Jan 2018 21:35:43 +0000 (22:35 +0100)]
ARM: dts: imx25-pinfunc: Use consistent naming for eSDHC
This file had several naming inconsistencies for eSDHC:
- the instances were named sometimes SDn, sometimes SDHCn, whereas they
are named ESDHCn in the reference manual, e.g.:
MX25_PAD_SD1_CMD__SD1_CMD
MX25_PAD_D15__SDHC1_DAT7
- the data ports were named sometimes DATAn, sometimes DATn like in the
reference manual, e.g.:
MX25_PAD_SD1_DATA0__SD1_DATA0
MX25_PAD_D15__SDHC1_DAT7
- in one case, the clock port was named DAT_CLK instead of CLK:
MX25_PAD_CSI_D7__SDHC2_DAT_CLK
This change:
- introduces new definitions using the naming from the reference
manual,
- keeps definitions using the legacy naming in order not to break
compatibility for out-of-tree users (they can be removed later),
- updates the in-tree files that were using the legacy naming.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bartosz Golaszewski [Wed, 24 Jan 2018 21:31:48 +0000 (22:31 +0100)]
ARM: dts: fix the at24 compatible string in imx6q-h100
Using 'at24' as fallback is now deprecated - use the full
'atmel,<model>' string.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bartosz Golaszewski [Wed, 24 Jan 2018 21:31:16 +0000 (22:31 +0100)]
ARM: dts: use 'atmel' as at24 manufacturer for imx6qdl-rex
Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bartosz Golaszewski [Wed, 24 Jan 2018 21:28:23 +0000 (22:28 +0100)]
ARM: dts: use 'atmel' as at24 manufacturer for imx6qdl-zii-rdu2
Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marco Franchi [Wed, 24 Jan 2018 13:22:14 +0000 (11:22 -0200)]
ARM: dts: imx: Add memory node unit name
Fix the following warnings from dtc by adding the unit name to memory
nodes:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Converted using the following command:
perl -p0777i -e 's/memory \{\n\t\treg = \<0x+([0-9a-f])/memory\@$1$\
0000000 \{\n\t\treg = <0x$1/m' `find ./arch/arm/boot/dts -name "imx*"`
The files below were manually fixed:
-imx1-ads.dts
-imx1-apf9328.dts
-imx6q-pistachio.dts
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marco Franchi [Wed, 24 Jan 2018 13:22:13 +0000 (11:22 -0200)]
ARM: dts: imx: Remove empty memory size nodes
Remove the empty reg property from the SoC dtsi files in order to avoid
duplicate memory nodes when the correct size is passed in board dts files.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marco Franchi [Wed, 24 Jan 2018 13:22:12 +0000 (11:22 -0200)]
ARM: dts: imx: Pass empty memory size on board dts
In preparation for removing 'reg = <0 0>;' from the dtsi SoC files, pass
'reg = <0 0 >;' to the dts/dtsi board files that do not pass the memory
size.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Tue, 23 Jan 2018 16:42:14 +0000 (00:42 +0800)]
ARM: dts: imx6sx: add ARM power domain support
Add ARM power domain in PGC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Tue, 23 Jan 2018 15:12:23 +0000 (23:12 +0800)]
ARM: dts: imx6sx: add pu power domain support
Add PU power domain support, GPU is the only
module inside PU power domain, and PU power
is supplied by LDO_SOC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ryan Harkin [Tue, 23 Jan 2018 12:37:30 +0000 (12:37 +0000)]
ARM: dts: imx7s-warp: enable uart6 on mikroBus
This patch configures the board to output UART6 to the mikroBus.
The NXP WaRP7 board can route UART6 to the mikroBus, where an RS232
click board can be plugged in to get an additional serial port.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ian Ray [Mon, 8 Jan 2018 11:29:01 +0000 (13:29 +0200)]
ARM: dts: imx6q-bx50v3: disable SD card
Default boot medium must be internal eMMC, we don't want the SDIO to be
used for these devices. This commit disables the SD card interface for
GE Healthcare Bx50v3 devices.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Sebastian Reichel [Mon, 15 Jan 2018 14:28:20 +0000 (15:28 +0100)]
ARM: dts: imx53-ppd: use PMIC's TSI pins in adc mode
PPD uses the PMIC's TSI pins in general purpose ADC mode.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Martyn Welch [Mon, 15 Jan 2018 14:24:52 +0000 (15:24 +0100)]
ARM: dts: imx53-ppd: Add touchscreen reset line
Utilise new support in Atmel MaxTouch driver to drive the
touchscreen controllers reset line correctly.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Wed, 10 Jan 2018 21:04:53 +0000 (22:04 +0100)]
ARM: dts: imx6ull: add UART8 support
In i.MX 6ULL UART8 is part of the AIPS-3 memory map instead of
AIPS-1. Clocks and interrupts remain the same.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Wed, 10 Jan 2018 21:04:52 +0000 (22:04 +0100)]
ARM: dts: imx6ull: add IOMUXC SNVS instance
The i.MX 6ULL features another IOMUX Controller called IOMUXC
SNVS which allows to control BOOT_MODE and TAMPER pins. Add the
controller to the i.MX 6ULL specific imx6ull.dtsi device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Wed, 10 Jan 2018 21:04:51 +0000 (22:04 +0100)]
ARM: dts: imx6ul: add ARM architected timer
Add per-core ARM architected timer. Unfortunately bootloaders (U-Boot)
currently do not make the necessary initialization. Also specifing the
clock manually using the clock-frequency property seems not to help.
Therefor leave the timer disabled by default for now.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Wed, 10 Jan 2018 21:04:50 +0000 (22:04 +0100)]
ARM: dts: imx6ul: add interrupt of virt-capable GIC
The Cortex-A7 and its GIC support virtualization extensions. To
make use of them the CPU private interrupt needs to be specified.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bai Ping [Wed, 10 Jan 2018 21:04:49 +0000 (22:04 +0100)]
ARM: dts: imx6ull: add additional pinfunc defines for i.MX 6ULL
On i.MX 6ULL, the pin MUX and CTRL register of BOOT_MODEx and TAMPERx
pins are available through IOMUXC_SNVS. Add additional pinfunc defines.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fugang Duan [Wed, 10 Jan 2018 21:04:48 +0000 (22:04 +0100)]
ARM: dts: imx6ul: update i.MX 6UltraLite iomux headers
Add previously missing daisy chain configurations and several
additional pinmux options.
Synchronized with NXP Linux 4.9.11_1.0.0 release.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enrico Scholz [Tue, 9 Jan 2018 16:09:59 +0000 (17:09 +0100)]
ARM: dts: imx6: Add support for phyBOARD-Mira with i.MX 6QuadPlus
Add support for the PHYTEC phyBOARD-Mira with i.MX 6QuadPlus with NAND.
It is based on the phyBOARD-Mira with i.MX 6Quad/Dual and supports the
same interfaces.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Stefan Lengfeld <s.lengfeld@phytec.de>
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Christian Hemp [Tue, 9 Jan 2018 16:09:58 +0000 (17:09 +0100)]
ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6 DualLight/Solo RDK
Add support for the PHYTEC phyBOARD-Mira Low-Cost Rapid Development Kit
with i.MX 6DualLight/Solo with NAND.
Following interfaces are supported:
- 100 MBit Ethernet
- USB Host
- RS232
- HDMI
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Christian Hemp [Tue, 9 Jan 2018 16:09:57 +0000 (17:09 +0100)]
ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6Quad/Dual RDK
Add support for the PHYTEC phyBOARD-Mira Rapid Development Kit with
i.MX 6Quad/Dual with eMMC or NAND.
Following interfaces are supported:
- Gigabit Ethernet
- USB Host
- CAN
- RS232
- PCIe
- LVDS
- HDMI
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Riedmueller [Tue, 9 Jan 2018 16:09:56 +0000 (17:09 +0100)]
ARM: dts: imx6: Add initial support for phyBOARD-Mira
This patch adds basic support for PHYTEC phyBOARD-Mira as carrier board
for PHYTEC phyCORE-i.MX 6.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Riedmueller [Tue, 9 Jan 2018 16:09:55 +0000 (17:09 +0100)]
ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM
This patch adds basic support for PHYTEC phyCORE-i.MX 6 SOM with i.MX
6Quad/Dual or i.MX 6DualLight/Solo.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marco Franchi [Tue, 9 Jan 2018 11:46:25 +0000 (09:46 -0200)]
ARM: dts: imx7d-sdb: Add support for mpl3115 sensor
The i.MX 7D SDB has a MPL3115 Pressure sensor.
Add support for this sensor, which is included in the trivial i2c devices
and according to the bindings documentation, just need a compatible field
and an address.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marco Franchi [Tue, 9 Jan 2018 11:46:23 +0000 (09:46 -0200)]
ARM: dts: imx6ul-evk: Add support for mag3110 sensor
The i.MX 6UL EVK has a MAG3110 Magnetometer sensor in its base board.
Add support for this sensor, which is included in the trivial i2c devices
and according to the bindings documentation, just need a compatible field
and an address.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lucas Stach [Wed, 3 Jan 2018 19:32:37 +0000 (11:32 -0800)]
ARM: dts: imx6: RDU2: disable internal watchdog
The system has an external watchdog in the environment processor
so the internal watchdog is of no use.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: cphealy@gmail.com
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Wed, 3 Jan 2018 11:22:14 +0000 (19:22 +0800)]
ARM: dts: imx6ul: remove unnecessary clocks for cpu-freq
Remove unnecessary clocks for cpu-freq driver to
avoid confusion.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 27 Dec 2017 16:23:23 +0000 (14:23 -0200)]
ARM: dts: imx27-eukrea-mbimxsd27-baseboard: Pass missing unit address
ads7846 is connected to SPI chip select 0, so pass the unit address
accordingly to fix the following build warning with W=1:
arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dtb: Warning (unit_address_vs_reg): Node /soc/aipi@
10000000/cspi@
1000e000/ads7846 has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 27 Dec 2017 14:04:38 +0000 (12:04 -0200)]
ARM: dts: imx28-
cfa10049: Move i2cmux out of bus node
Move i2cmux node from soc node to root node.
i2cmux node does not have any register properties and thus shouldn't be
placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx28-
cfa10049.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbx@
80040000/i2cmux missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 27 Dec 2017 14:04:37 +0000 (12:04 -0200)]
ARM: dts: imx28-apx4devkit: Pass unit address and reg to IOMUX node
Pass unit address and reg to IOMUX node to fix the following build
warning with W=1:
arch/arm/boot/dts/imx28-apx4devkit.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/mmc2-sck-cfg-apx4 missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 27 Dec 2017 14:04:36 +0000 (12:04 -0200)]
ARM: dts: imx28-tx28: Pass unit address and reg to IOMUX node
Pass unit address and reg to IOMUX node to fix the following build
warning with W=1:
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/tx28-edt-ft5x06-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/tx28-flexcan-xcvr-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/tx28-lcdif-23bit missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/tx28-lcdif-ctrl missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/tx28-mac0-gpio-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/tx28-pca9554-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/spi-gpiogrp missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/tx28-tsc2007-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/tx28-usbphy0-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/tx28-usbphy1-pins missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 27 Dec 2017 14:04:35 +0000 (12:04 -0200)]
ARM: dts: imx28: Pass unit address and reg to IOMUX node
Pass unit address and reg to IOMUX node to fix the following build
warning with W=1:
arch/arm/boot/dts/imx28-apf28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/gpmi-status-cfg missing or empty reg/ranges property
arch/arm/boot/dts/imx28-apf28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/mmc0-cd-cfg missing or empty reg/ranges property
arch/arm/boot/dts/imx28-apf28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/mmc0-sck-cfg missing or empty reg/ranges property
arch/arm/boot/dts/imx28-apf28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/mmc1-cd-cfg missing or empty reg/ranges property
arch/arm/boot/dts/imx28-apf28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/mmc1-sck-cfg missing or empty reg/ranges property
arch/arm/boot/dts/imx28-apf28.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/mmc2-cd-cfg missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 27 Dec 2017 14:04:34 +0000 (12:04 -0200)]
ARM: dts: imx23: Pass unit address and reg to IOMUX node
Pass unit address and reg to IOMUX node to fix the following build
warning with W=1:
arch/arm/boot/dts/imx23-evk.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/gpmi-pins-fixup missing or empty reg/ranges property
arch/arm/boot/dts/imx23-evk.dtb: Warning (simple_bus_reg): Node /apb@
80000000/apbh@
80000000/pinctrl@
80018000/mmc0-pins-fixup missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rasmus Villemoes [Wed, 3 Jan 2018 15:45:45 +0000 (16:45 +0100)]
ARM: dts: ls1021a: add nodes for on-chip ram
Although the two nodes constitute one contiguous 128K region, still
describe them separately:
- That's how they are described in the reference manual: "Each OCRAM
occupies a 64 KB of address region...", and the names ocram1 and
ocram2 are also as used in the manual.
- The two areas are treated differently by the boot ROM code: OCRAM2 is
zero-initialized, while, again quoting the RM, "software must perform
the zero initialization of OCRAM1."
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Linus Torvalds [Sun, 11 Feb 2018 23:04:29 +0000 (15:04 -0800)]
Linux 4.16-rc1
Al Viro [Thu, 1 Feb 2018 20:13:18 +0000 (15:13 -0500)]
unify {de,}mangle_poll(), get rid of kernel-side POLL...
except, again, POLLFREE and POLL_BUSY_LOOP.
With this, we finally get to the promised end result:
- POLL{IN,OUT,...} are plain integers and *not* in __poll_t, so any
stray instances of ->poll() still using those will be caught by
sparse.
- eventpoll.c and select.c warning-free wrt __poll_t
- no more kernel-side definitions of POLL... - userland ones are
visible through the entire kernel (and used pretty much only for
mangle/demangle)
- same behavior as after the first series (i.e. sparc et.al. epoll(2)
working correctly).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 11 Feb 2018 22:34:03 +0000 (14:34 -0800)]
vfs: do bulk POLL* -> EPOLL* replacement
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 11 Feb 2018 21:57:19 +0000 (13:57 -0800)]
Merge branch 'work.poll2' of git://git./linux/kernel/git/viro/vfs
Pull more poll annotation updates from Al Viro:
"This is preparation to solving the problems you've mentioned in the
original poll series.
After this series, the kernel is ready for running
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
as a for bulk search-and-replace.
After that, the kernel is ready to apply the patch to unify
{de,}mangle_poll(), and then get rid of kernel-side POLL... uses
entirely, and we should be all done with that stuff.
Basically, that's what you suggested wrt KPOLL..., except that we can
use EPOLL... instead - they already are arch-independent (and equal to
what is currently kernel-side POLL...).
After the preparations (in this series) switch to returning EPOLL...
from ->poll() instances is completely mechanical and kernel-side
POLL... can go away. The last step (killing kernel-side POLL... and
unifying {de,}mangle_poll() has to be done after the
search-and-replace job, since we need userland-side POLL... for
unified {de,}mangle_poll(), thus the cherry-pick at the last step.
After that we will have:
- POLL{IN,OUT,...} *not* in __poll_t, so any stray instances of
->poll() still using those will be caught by sparse.
- eventpoll.c and select.c warning-free wrt __poll_t
- no more kernel-side definitions of POLL... - userland ones are
visible through the entire kernel (and used pretty much only for
mangle/demangle)
- same behavior as after the first series (i.e. sparc et.al. epoll(2)
working correctly)"
* 'work.poll2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
annotate ep_scan_ready_list()
ep_send_events_proc(): return result via esed->res
preparation to switching ->poll() to returning EPOLL...
add EPOLLNVAL, annotate EPOLL... and event_poll->event
use linux/poll.h instead of asm/poll.h
xen: fix poll misannotation
smc: missing poll annotations
Linus Torvalds [Sun, 11 Feb 2018 21:54:52 +0000 (13:54 -0800)]
Merge tag 'xtensa-
20180211' of git://github.com/jcmvbkbc/linux-xtensa
Pull xtense fix from Max Filippov:
"Build fix for xtensa architecture with KASAN enabled"
* tag 'xtensa-
20180211' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: fix build with KASAN
Linus Torvalds [Sun, 11 Feb 2018 21:52:32 +0000 (13:52 -0800)]
Merge tag 'nios2-v4.16-rc1' of git://git./linux/kernel/git/lftan/nios2
Pull nios2 update from Ley Foon Tan:
- clean up old Kconfig options from defconfig
- remove leading 0x and 0s from bindings notation in dts files
* tag 'nios2-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: defconfig: Cleanup from old Kconfig options
nios2: dts: Remove leading 0x and 0s from bindings notation
Max Filippov [Sun, 11 Feb 2018 09:07:54 +0000 (01:07 -0800)]
xtensa: fix build with KASAN
The commit
917538e212a2 ("kasan: clean up KASAN_SHADOW_SCALE_SHIFT
usage") removed KASAN_SHADOW_SCALE_SHIFT definition from
include/linux/kasan.h and added it to architecture-specific headers,
except for xtensa. This broke the xtensa build with KASAN enabled.
Define KASAN_SHADOW_SCALE_SHIFT in arch/xtensa/include/asm/kasan.h
Reported by: kbuild test robot <fengguang.wu@intel.com>
Fixes:
917538e212a2 ("kasan: clean up KASAN_SHADOW_SCALE_SHIFT usage")
Acked-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Krzysztof Kozlowski [Sun, 11 Feb 2018 15:01:17 +0000 (23:01 +0800)]
nios2: defconfig: Cleanup from old Kconfig options
Remove old, dead Kconfig option INET_LRO. It is gone since
commit
7bbf3cae65b6 ("ipv4: Remove inet_lro library").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
Mathieu Malaterre [Sun, 11 Feb 2018 14:59:18 +0000 (22:59 +0800)]
nios2: dts: Remove leading 0x and 0s from bindings notation
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit
4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
Linus Torvalds [Sat, 10 Feb 2018 22:08:26 +0000 (14:08 -0800)]
Merge tag 'pci-v4.16-fixes-1' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Fix a POWER9/powernv INTx regression from the merge window (Alexey
Kardashevskiy)"
* tag 'pci-v4.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
powerpc/pci: Fix broken INTx configuration via OF
Linus Torvalds [Sat, 10 Feb 2018 22:05:11 +0000 (14:05 -0800)]
Merge tag 'for-linus-
20180210' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A few fixes to round off the merge window on the block side:
- a set of bcache fixes by way of Michael Lyle, from the usual bcache
suspects.
- add a simple-to-hook-into function for bpf EIO error injection.
- fix blk-wbt that mischarectized flushes as reads. Improve the logic
so that flushes and writes are accounted as writes, and only reads
as reads. From me.
- fix requeue crash in BFQ, from Paolo"
* tag 'for-linus-
20180210' of git://git.kernel.dk/linux-block:
block, bfq: add requeue-request hook
bcache: fix for data collapse after re-attaching an attached device
bcache: return attach error when no cache set exist
bcache: set writeback_rate_update_seconds in range [1, 60] seconds
bcache: fix for allocator and register thread race
bcache: set error_limit correctly
bcache: properly set task state in bch_writeback_thread()
bcache: fix high CPU occupancy during journal
bcache: add journal statistic
block: Add should_fail_bio() for bpf error injection
blk-wbt: account flush requests correctly
Linus Torvalds [Sat, 10 Feb 2018 21:55:33 +0000 (13:55 -0800)]
Merge tag 'platform-drivers-x86-v4.16-3' of git://github.com/dvhart/linux-pdx86
Pull x86 platform driver updates from Darren Hart:
"Mellanox fixes and new system type support.
Mostly data for new system types with a correction and an
uninitialized variable fix"
[ Pulling from github because git.infradead.org currently seems to be
down for some reason, but Darren had a backup location - Linus ]
* tag 'platform-drivers-x86-v4.16-3' of git://github.com/dvhart/linux-pdx86:
platform/x86: mlx-platform: Add support for new 200G IB and Ethernet systems
platform/x86: mlx-platform: Add support for new msn201x system type
platform/x86: mlx-platform: Add support for new msn274x system type
platform/x86: mlx-platform: Fix power cable setting for msn21xx family
platform/x86: mlx-platform: Add define for the negative bus
platform/x86: mlx-platform: Use defines for bus assignment
platform/mellanox: mlxreg-hotplug: Fix uninitialized variable
Linus Torvalds [Sat, 10 Feb 2018 21:50:23 +0000 (13:50 -0800)]
Merge tag 'chrome-platform-for-linus-4.16' of git://git./linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
- move cros_ec_dev to drivers/mfd
- other small maintenance fixes
[ The cros_ec_dev movement came in earlier through the MFD tree - Linus ]
* tag 'chrome-platform-for-linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome: Use proper protocol transfer function
platform/chrome: cros_ec_lpc: Add support for Google Glimmer
platform/chrome: cros_ec_lpc: Register the driver if ACPI entry is missing.
platform/chrome: cros_ec_lpc: remove redundant pointer request
cros_ec: fix nul-termination for firmware build info
platform/chrome: chromeos_laptop: make chromeos_laptop const
Linus Torvalds [Sat, 10 Feb 2018 21:16:35 +0000 (13:16 -0800)]
Merge tag 'kvm-4.16-1' of git://git./virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"ARM:
- icache invalidation optimizations, improving VM startup time
- support for forwarded level-triggered interrupts, improving
performance for timers and passthrough platform devices
- a small fix for power-management notifiers, and some cosmetic
changes
PPC:
- add MMIO emulation for vector loads and stores
- allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without
requiring the complex thread synchronization of older CPU versions
- improve the handling of escalation interrupts with the XIVE
interrupt controller
- support decrement register migration
- various cleanups and bugfixes.
s390:
- Cornelia Huck passed maintainership to Janosch Frank
- exitless interrupts for emulated devices
- cleanup of cpuflag handling
- kvm_stat counter improvements
- VSIE improvements
- mm cleanup
x86:
- hypervisor part of SEV
- UMIP, RDPID, and MSR_SMI_COUNT emulation
- paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit
- allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more
AVX512 features
- show vcpu id in its anonymous inode name
- many fixes and cleanups
- per-VCPU MSR bitmaps (already merged through x86/pti branch)
- stable KVM clock when nesting on Hyper-V (merged through
x86/hyperv)"
* tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (197 commits)
KVM: PPC: Book3S: Add MMIO emulation for VMX instructions
KVM: PPC: Book3S HV: Branch inside feature section
KVM: PPC: Book3S HV: Make HPT resizing work on POWER9
KVM: PPC: Book3S HV: Fix handling of secondary HPTEG in HPT resizing code
KVM: PPC: Book3S PR: Fix broken select due to misspelling
KVM: x86: don't forget vcpu_put() in kvm_arch_vcpu_ioctl_set_sregs()
KVM: PPC: Book3S PR: Fix svcpu copying with preemption enabled
KVM: PPC: Book3S HV: Drop locks before reading guest memory
kvm: x86: remove efer_reload entry in kvm_vcpu_stat
KVM: x86: AMD Processor Topology Information
x86/kvm/vmx: do not use vm-exit instruction length for fast MMIO when running nested
kvm: embed vcpu id to dentry of vcpu anon inode
kvm: Map PFN-type memory regions as writable (if possible)
x86/kvm: Make it compile on 32bit and with HYPYERVISOR_GUEST=n
KVM: arm/arm64: Fixup userspace irqchip static key optimization
KVM: arm/arm64: Fix userspace_irqchip_in_use counting
KVM: arm/arm64: Fix incorrect timer_is_pending logic
MAINTAINERS: update KVM/s390 maintainers
MAINTAINERS: add Halil as additional vfio-ccw maintainer
MAINTAINERS: add David as a reviewer for KVM/s390
...
Alexey Kardashevskiy [Fri, 9 Feb 2018 06:23:58 +0000 (17:23 +1100)]
powerpc/pci: Fix broken INTx configuration via OF
59f47eff03a0 ("powerpc/pci: Use of_irq_parse_and_map_pci() helper")
replaced of_irq_parse_pci() + irq_create_of_mapping() with
of_irq_parse_and_map_pci(), but neglected to capture the virq
returned by irq_create_of_mapping(), so virq remained zero, which
caused INTx configuration to fail.
Save the virq value returned by of_irq_parse_and_map_pci() and correct
the virq declaration to match the of_irq_parse_and_map_pci() signature.
Fixes:
59f47eff03a0 "powerpc/pci: Use of_irq_parse_and_map_pci() helper"
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Linus Torvalds [Sat, 10 Feb 2018 03:32:41 +0000 (19:32 -0800)]
Merge tag 'kbuild-v4.16-2' of git://git./linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
"Makefile changes:
- enable unused-variable warning that was wrongly disabled for clang
Kconfig changes:
- warn about blank 'help' and fix existing instances
- fix 'choice' behavior to not write out invisible symbols
- fix misc weirdness
Coccinell changes:
- fix false positive of free after managed memory alloc detection
- improve performance of NULL dereference detection"
* tag 'kbuild-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (21 commits)
kconfig: remove const qualifier from sym_expand_string_value()
kconfig: add xrealloc() helper
kconfig: send error messages to stderr
kconfig: echo stdin to stdout if either is redirected
kconfig: remove check_stdin()
kconfig: remove 'config*' pattern from .gitignnore
kconfig: show '?' prompt even if no help text is available
kconfig: do not write choice values when their dependency becomes n
coccinelle: deref_null: avoid useless computation
coccinelle: devm_free: reduce false positives
kbuild: clang: disable unused variable warnings only when constant
kconfig: Warn if help text is blank
nios2: kconfig: Remove blank help text
arm: vt8500: kconfig: Remove blank help text
MIPS: kconfig: Remove blank help text
MIPS: BCM63XX: kconfig: Remove blank help text
lib/Kconfig.debug: Remove blank help text
Staging: rtl8192e: kconfig: Remove blank help text
Staging: rtl8192u: kconfig: Remove blank help text
mmc: kconfig: Remove blank help text
...
Al Viro [Sat, 10 Feb 2018 01:35:16 +0000 (01:35 +0000)]
mconsole_proc(): don't mess with file->f_pos
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 10 Feb 2018 03:22:17 +0000 (19:22 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull misc vfs fixes from Al Viro.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
seq_file: fix incomplete reset on read from zero offset
kernfs: fix regression in kernfs_fop_write caused by wrong type
Masahiro Yamada [Thu, 8 Feb 2018 16:19:08 +0000 (01:19 +0900)]
kconfig: remove const qualifier from sym_expand_string_value()
This function returns realloc'ed memory, so the returned pointer
must be passed to free() when done. So, 'const' qualifier is odd.
It is allowed to modify the expanded string.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 8 Feb 2018 16:19:07 +0000 (01:19 +0900)]
kconfig: add xrealloc() helper
We already have xmalloc(), xcalloc(). Add xrealloc() as well
to save tedious error handling.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Vadim Pasternak [Fri, 9 Feb 2018 23:59:32 +0000 (23:59 +0000)]
platform/x86: mlx-platform: Add support for new 200G IB and Ethernet systems
It adds support for new Mellanox system types of basic classes qmb7, sn34,
sn37, containing systems QMB700 (40x200GbE InfiniBand switch), SN3700
(32x200GbE and 16x400GbE Ethernet switch) and SN3410 (6x400GbE plus
48x50GbE Ethernet switch). These are the Top of the Rack systems, equipped
with Mellanox COM-Express carrier board and switch board with Mellanox
Quantum device, which supports InfiniBand switching with 40X200G ports and
line rate of up to HDR speed or with Mellanox Spectrum-2 device, which
supports Ethernet switching with 32X200G ports line rate of up to HDR
speed.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Vadim Pasternak [Fri, 9 Feb 2018 23:59:31 +0000 (23:59 +0000)]
platform/x86: mlx-platform: Add support for new msn201x system type
It adds support for new Mellanox system types of basic half unit size
class msn201x, containing system MSN2010 (18x10GbE plus 4x4x25GbE) half
and its derivatives. This is the Top of the Rack system, equipped with
Mellanox Small Form Factor carrier board and switch board with Mellanox
Spectrum device, which supports Ethernet switching with 32X100G ports line
rate of up to EDR speed.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Vadim Pasternak [Fri, 9 Feb 2018 23:59:30 +0000 (23:59 +0000)]
platform/x86: mlx-platform: Add support for new msn274x system type
It adds support for new Mellanox system types of basic class msn274x,
containing system MSN2740 (32x100GbE Ethernet switch with cost reduction)
and its derivatives. These are the Top of the Rack system, equipped with
Mellanox Small Form Factor carrier board and switch board with Mellanox
Spectrum device, which supports Ethernet switching with 32X100G ports line
rate of up to EDR speed.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Linus Torvalds [Fri, 9 Feb 2018 23:34:18 +0000 (15:34 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Make allocations less aggressive in x_tables, from Minchal Hocko.
2) Fix netfilter flowtable Kconfig deps, from Pablo Neira Ayuso.
3) Fix connection loss problems in rtlwifi, from Larry Finger.
4) Correct DRAM dump length for some chips in ath10k driver, from Yu
Wang.
5) Fix ABORT handling in rxrpc, from David Howells.
6) Add SPDX tags to Sun networking drivers, from Shannon Nelson.
7) Some ipv6 onlink handling fixes, from David Ahern.
8) Netem packet scheduler interval calcualtion fix from Md. Islam.
9) Don't put crypto buffers on-stack in rxrpc, from David Howells.
10) Fix handling of error non-delivery status in netlink multicast
delivery over multiple namespaces, from Nicolas Dichtel.
11) Missing xdp flush in tuntap driver, from Jason Wang.
12) Synchonize RDS protocol netns/module teardown with rds object
management, from Sowini Varadhan.
13) Add nospec annotations to mpls, from Dan Williams.
14) Fix SKB truesize handling in TIPC, from Hoang Le.
15) Interrupt masking fixes in stammc from Niklas Cassel.
16) Don't allow ptr_ring objects to be sized outside of kmalloc's
limits, from Jason Wang.
17) Don't allow SCTP chunks to be built which will have a length
exceeding the chunk header's 16-bit length field, from Alexey
Kodanev.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (82 commits)
ibmvnic: Remove skb->protocol checks in ibmvnic_xmit
bpf: fix rlimit in reuseport net selftest
sctp: verify size of a new chunk in _sctp_make_chunk()
s390/qeth: fix SETIP command handling
s390/qeth: fix underestimated count of buffer elements
ptr_ring: try vmalloc() when kmalloc() fails
ptr_ring: fail early if queue occupies more than KMALLOC_MAX_SIZE
net: stmmac: remove redundant enable of PMT irq
net: stmmac: rename GMAC_INT_DEFAULT_MASK for dwmac4
net: stmmac: discard disabled flags in interrupt status register
ibmvnic: Reset long term map ID counter
tools/libbpf: handle issues with bpf ELF objects containing .eh_frames
selftests/bpf: add selftest that use test_libbpf_open
selftests/bpf: add test program for loading BPF ELF files
tools/libbpf: improve the pr_debug statements to contain section numbers
bpf: Sync kernel ABI header with tooling header for bpf_common.h
net: phy: fix phy_start to consider PHY_IGNORE_INTERRUPT
net: thunder: change q_len's type to handle max ring size
tipc: fix skb truesize/datasize ratio control
net/sched: cls_u32: fix cls_u32 on filter replace
...
Linus Torvalds [Fri, 9 Feb 2018 22:55:30 +0000 (14:55 -0800)]
Merge tag 'nfs-for-4.16-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull more NFS client updates from Trond Myklebust:
"A few bugfixes and some small sunrpc latency/performance improvements
before the merge window closes:
Stable fixes:
- fix an incorrect calculation of the RDMA send scatter gather
element limit
- fix an Oops when attempting to free resources after RDMA device
removal
Bugfixes:
- SUNRPC: Ensure we always release the TCP socket in a timely fashion
when the connection is shut down.
- SUNRPC: Don't call __UDPX_INC_STATS() from a preemptible context
Latency/Performance:
- SUNRPC: Queue latency sensitive socket tasks to the less contended
xprtiod queue
- SUNRPC: Make the xprtiod workqueue unbounded.
- SUNRPC: Make the rpciod workqueue unbounded"
* tag 'nfs-for-4.16-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Don't call __UDPX_INC_STATS() from a preemptible context
fix parallelism for rpc tasks
Make the xprtiod workqueue unbounded.
SUNRPC: Queue latency-sensitive socket tasks to xprtiod
SUNRPC: Ensure we always close the socket after a connection shuts down
xprtrdma: Fix BUG after a device removal
xprtrdma: Fix calculation of ri_max_send_sges
Linus Torvalds [Fri, 9 Feb 2018 22:49:46 +0000 (14:49 -0800)]
Merge branch 'for-next' of git://git./linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"The highlights include:
- numerous target-core-user improvements related to queue full and
timeout handling. (MNC)
- prevent target-core-user corruption when invalid data page is
requested. (MNC)
- add target-core device action configfs attributes to allow
user-space to trigger events separate from existing attributes
exposed to end-users. (MNC)
- fix iscsi-target NULL pointer dereference 4.6+ regression in CHAP
error path. (David Disseldorp)
- avoid target-core backend UNMAP callbacks if range is zero. (Andrei
Vagin)
- fix a iscsi-target 4.14+ regression related multiple PDU logins,
that was exposed due to removal of TCP prequeue support. (Florian
Westphal + MNC)
Also, there is a iser-target bug still being worked on for post -rc1
code to address a long standing issue resulting in persistent
ib_post_send() failures, for RNICs with small max_send_sge"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (36 commits)
iscsi-target: make sure to wake up sleeping login worker
tcmu: Fix trailing semicolon
tcmu: fix cmd user after free
target: fix destroy device in target_configure_device
tcmu: allow userspace to reset ring
target core: add device action configfs files
tcmu: fix error return code in tcmu_configure_device()
target_core_user: add cmd id to broken ring message
target: add SAM_STAT_BUSY sense reason
tcmu: prevent corruption when invalid data page requested
target: don't call an unmap callback if a range length is zero
target/iscsi: avoid NULL dereference in CHAP auth error path
cxgbit: call neigh_event_send() to update MAC address
target: tcm_loop: Use seq_puts() in tcm_loop_show_info()
target: tcm_loop: Delete an unnecessary return statement in tcm_loop_submission_work()
target: tcm_loop: Delete two unnecessary variable initialisations in tcm_loop_issue_tmr()
target: tcm_loop: Combine substrings for 26 messages
target: tcm_loop: Improve a size determination in two functions
target: tcm_loop: Delete an error message for a failed memory allocation in four functions
sbp-target: Delete an error message for a failed memory allocation in three functions
...
Linus Torvalds [Fri, 9 Feb 2018 22:47:09 +0000 (14:47 -0800)]
Merge tag 'trace-v4.16-rc1' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Al Viro discovered some breakage with the parsing of the
set_ftrace_filter as well as the removing of function probes.
This fixes the code with Al's suggestions. I also added a few
selftests to test the broken cases such that they wont happen
again"
* tag 'trace-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
selftests/ftrace: Add more tests for removing of function probes
selftests/ftrace: Add some missing glob checks
selftests/ftrace: Have reset_ftrace_filter handle multiple instances
selftests/ftrace: Have reset_ftrace_filter handle modules
tracing: Fix parsing of globs with a wildcard at the beginning
ftrace: Remove incorrect setting of glob search field
Linus Torvalds [Fri, 9 Feb 2018 22:42:57 +0000 (14:42 -0800)]
Merge tag '4.16-minor-rc-SMB3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"There are a couple additional security fixes that are still being
tested that are not in this set."
* tag '4.16-minor-rc-SMB3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
Add missing structs and defines from recent SMB3.1.1 documentation
address lock imbalance warnings in smbdirect.c
cifs: silence compiler warnings showing up with gcc-8.0.0
Add some missing debug fields in server and tcon structs
Linus Torvalds [Fri, 9 Feb 2018 22:40:16 +0000 (14:40 -0800)]
Merge tag 'fbdev-v4.16-fix' of git://github.com/bzolnier/linux
Pull fbdev fix from Bartlomiej Zolnierkiewicz:
"Fix building of the omapfb driver (Tomi Valkeinen)"
* tag 'fbdev-v4.16-fix' of git://github.com/bzolnier/linux:
video: omapfb: fix missing #includes
Radim Krčmář [Fri, 9 Feb 2018 20:36:57 +0000 (21:36 +0100)]
Merge tag 'kvm-ppc-next-4.16-2' of git://git./linux/kernel/git/paulus/powerpc
Second PPC KVM update for 4.16
Seven fixes that are either trivial or that address bugs that people
are actually hitting. The main ones are:
- Drop spinlocks before reading guest memory
- Fix a bug causing corruption of VCPU state in PR KVM with preemption
enabled
- Make HPT resizing work on POWER9
- Add MMIO emulation for vector loads and stores, because guests now
use these instructions in memcpy and similar routines.
Radim Krčmář [Fri, 2 Feb 2018 17:26:58 +0000 (18:26 +0100)]
Merge branch 'msr-bitmaps' of git://git./virt/kvm/kvm
This topic branch allocates separate MSR bitmaps for each VCPU.
This is required for the IBRS enablement to choose, on a per-VM
basis, whether to intercept the SPEC_CTRL and PRED_CMD MSRs;
the IBRS enablement comes in through the tip tree.
John Allen [Fri, 9 Feb 2018 19:19:46 +0000 (13:19 -0600)]
ibmvnic: Remove skb->protocol checks in ibmvnic_xmit
Having these checks in ibmvnic_xmit causes problems with VLAN
tagging and balance-alb/tlb bonding modes. The restriction they
imposed can be removed.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 9 Feb 2018 13:49:44 +0000 (14:49 +0100)]
bpf: fix rlimit in reuseport net selftest
Fix two issues in the reuseport_bpf selftests that were
reported by Linaro CI:
[...]
+ ./reuseport_bpf
---- IPv4 UDP ----
Testing EBPF mod 10...
Reprograming, testing mod 5...
./reuseport_bpf: ebpf error. log:
0: (bf) r6 = r1
1: (20) r0 = *(u32 *)skb[0]
2: (97) r0 %= 10
3: (95) exit
processed 4 insns
: Operation not permitted
+ echo FAIL
[...]
---- IPv4 TCP ----
Testing EBPF mod 10...
./reuseport_bpf: failed to bind send socket: Address already in use
+ echo FAIL
[...]
For the former adjust rlimit since this was the cause of
failure for loading the BPF prog, and for the latter add
SO_REUSEADDR.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://bugs.linaro.org/show_bug.cgi?id=3502
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kodanev [Fri, 9 Feb 2018 14:35:23 +0000 (17:35 +0300)]
sctp: verify size of a new chunk in _sctp_make_chunk()
When SCTP makes INIT or INIT_ACK packet the total chunk length
can exceed SCTP_MAX_CHUNK_LEN which leads to kernel panic when
transmitting these packets, e.g. the crash on sending INIT_ACK:
[ 597.804948] skbuff: skb_over_panic: text:
00000000ffae06e4 len:120168
put:120156 head:
000000007aa47635 data:
00000000d991c2de
tail:0x1d640 end:0xfec0 dev:<NULL>
...
[ 597.976970] ------------[ cut here ]------------
[ 598.033408] kernel BUG at net/core/skbuff.c:104!
[ 600.314841] Call Trace:
[ 600.345829] <IRQ>
[ 600.371639] ? sctp_packet_transmit+0x2095/0x26d0 [sctp]
[ 600.436934] skb_put+0x16c/0x200
[ 600.477295] sctp_packet_transmit+0x2095/0x26d0 [sctp]
[ 600.540630] ? sctp_packet_config+0x890/0x890 [sctp]
[ 600.601781] ? __sctp_packet_append_chunk+0x3b4/0xd00 [sctp]
[ 600.671356] ? sctp_cmp_addr_exact+0x3f/0x90 [sctp]
[ 600.731482] sctp_outq_flush+0x663/0x30d0 [sctp]
[ 600.788565] ? sctp_make_init+0xbf0/0xbf0 [sctp]
[ 600.845555] ? sctp_check_transmitted+0x18f0/0x18f0 [sctp]
[ 600.912945] ? sctp_outq_tail+0x631/0x9d0 [sctp]
[ 600.969936] sctp_cmd_interpreter.isra.22+0x3be1/0x5cb0 [sctp]
[ 601.041593] ? sctp_sf_do_5_1B_init+0x85f/0xc30 [sctp]
[ 601.104837] ? sctp_generate_t1_cookie_event+0x20/0x20 [sctp]
[ 601.175436] ? sctp_eat_data+0x1710/0x1710 [sctp]
[ 601.233575] sctp_do_sm+0x182/0x560 [sctp]
[ 601.284328] ? sctp_has_association+0x70/0x70 [sctp]
[ 601.345586] ? sctp_rcv+0xef4/0x32f0 [sctp]
[ 601.397478] ? sctp6_rcv+0xa/0x20 [sctp]
...
Here the chunk size for INIT_ACK packet becomes too big, mostly
because of the state cookie (INIT packet has large size with
many address parameters), plus additional server parameters.
Later this chunk causes the panic in skb_put_data():
skb_packet_transmit()
sctp_packet_pack()
skb_put_data(nskb, chunk->skb->data, chunk->skb->len);
'nskb' (head skb) was previously allocated with packet->size
from u16 'chunk->chunk_hdr->length'.
As suggested by Marcelo we should check the chunk's length in
_sctp_make_chunk() before trying to allocate skb for it and
discard a chunk if its size bigger than SCTP_MAX_CHUNK_LEN.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leinter@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 9 Feb 2018 19:30:23 +0000 (14:30 -0500)]
Merge branch 's390-qeth-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2018-02-09
please apply the following two qeth patches for 4.16 and stable.
One restricts a command quirk to the intended commandd type,
while the other fixes an off-by-one during data transmission
that can cause qeth to build malformed buffer descriptors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 9 Feb 2018 10:03:50 +0000 (11:03 +0100)]
s390/qeth: fix SETIP command handling
send_control_data() applies some special handling to SETIP v4 IPA
commands. But current code parses *all* command types for the SETIP
command code. Limit the command code check to IPA commands.
Fixes:
5b54e16f1a54 ("qeth: do not spin for SETIP ip assist command")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Fri, 9 Feb 2018 10:03:49 +0000 (11:03 +0100)]
s390/qeth: fix underestimated count of buffer elements
For a memory range/skb where the last byte falls onto a page boundary
(ie. 'end' is of the form xxx...xxx001), the PFN_UP() part of the
calculation currently doesn't round up to the next PFN due to an
off-by-one error.
Thus qeth believes that the skb occupies one page less than it
actually does, and may select a IO buffer that doesn't have enough spare
buffer elements to fit all of the skb's data.
HW detects this as a malformed buffer descriptor, and raises an
exception which then triggers device recovery.
Fixes:
2863c61334aa ("qeth: refactor calculation of SBALE count")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Fri, 9 Feb 2018 09:45:50 +0000 (17:45 +0800)]
ptr_ring: try vmalloc() when kmalloc() fails
This patch switch to use kvmalloc_array() for using a vmalloc()
fallback to help in case kmalloc() fails.
Reported-by: syzbot+e4d4f9ddd4295539735d@syzkaller.appspotmail.com
Fixes:
2e0ab8ca83c12 ("ptr_ring: array based FIFO for pointers")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Fri, 9 Feb 2018 09:45:49 +0000 (17:45 +0800)]
ptr_ring: fail early if queue occupies more than KMALLOC_MAX_SIZE
To avoid slab to warn about exceeded size, fail early if queue
occupies more than KMALLOC_MAX_SIZE.
Reported-by: syzbot+e4d4f9ddd4295539735d@syzkaller.appspotmail.com
Fixes:
2e0ab8ca83c12 ("ptr_ring: array based FIFO for pointers")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>