git.osdn.net Git - tomoyo/tomoyo-test1.git/log

Merge branch 'VLAN-fixes-for-Ocelot-switch'

Vladimir Oltean says:

====================
VLAN fixes for Ocelot switch

This series addresses 2 issues with vlan_filtering=1:
- Untagged traffic gets dropped unless commands are run in a very
specific order.
- Untagged traffic starts being transmitted as tagged after adding
another untagged VID on the port.

Tested on NXP LS1028A-RDB board.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: refuse to overwrite the port's native vlan

The switch driver keeps a "vid" variable per port, which signifies _the_
VLAN ID that is stripped on that port's egress (aka the native VLAN on a
trunk port).

That is the way the hardware is designed (mostly). The port->vid is
programmed into REW:PORT:PORT_VLAN_CFG:PORT_VID and the rewriter is told
to send all traffic as tagged except the one having port->vid.

There exists a possibility of finer-grained egress untagging decisions:
using the VCAP IS1 engine, one rule can be added to match every
VLAN-tagged frame whose VLAN should be untagged, and set POP_CNT=1 as
action. However, the IS1 can hold at most 512 entries, and the VLANs are
in the order of 6 * 4096.

So the code is fine for now. But this sequence of commands:

$ bridge vlan add dev swp0 vid 1 pvid untagged
$ bridge vlan add dev swp0 vid 2 untagged

makes untagged and pvid-tagged traffic be sent out of swp0 as tagged
with VID 1, despite user's request.

Prevent that from happening. The user should temporarily remove the
existing untagged VLAN (1 in this case), add it back as tagged, and then
add the new untagged VLAN (2 in this case).

Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fixes: 7142529f1688 ("net: mscc: ocelot: add VLAN filtering")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: fix vlan_filtering when enslaving to bridge before link is up

Background information: the driver operates the hardware in a mode where
a single VLAN can be transmitted as untagged on a particular egress
port. That is the "native VLAN on trunk port" use case. Its value is
held in port->vid.

Consider the following command sequence (no network manager, all
interfaces are down, debugging prints added by me):

$ ip link add dev br0 type bridge vlan_filtering 1
$ ip link set dev swp0 master br0

Kernel code path during last command:

br_add_slave -> ocelot_netdevice_port_event (NETDEV_CHANGEUPPER):
[   21.401901] ocelot_vlan_port_apply: port 0 vlan aware 0 pvid 0 vid 0

br_add_slave -> nbp_vlan_init -> switchdev_port_attr_set -> ocelot_port_attr_set (SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING):
[   21.413335] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 0 vid 0

br_add_slave -> nbp_vlan_init -> nbp_vlan_add -> br_switchdev_port_vlan_add -> switchdev_port_obj_add -> ocelot_port_obj_add -> ocelot_vlan_vid_add
[   21.667421] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 1

So far so good. The bridge has replaced the driver's default pvid used
in standalone mode (0) with its own default_pvid (1). The port's vid
(native VLAN) has also changed from 0 to 1.

$ ip link set dev swp0 up

[   31.722956] 8021q: adding VLAN 0 to HW filter on device swp0
do_setlink -> dev_change_flags -> vlan_vid_add -> ocelot_vlan_rx_add_vid -> ocelot_vlan_vid_add:
[   31.728700] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 0

The 8021q module uses the .ndo_vlan_rx_add_vid API on .ndo_open to make
ports be able to transmit and receive 802.1p-tagged traffic by default.
This API is supposed to offload a VLAN sub-interface, which for a switch
port means to add a VLAN that is not a pvid, and tagged on egress.

But the driver implementation of .ndo_vlan_rx_add_vid is wrong: it adds
back vid 0 as "egress untagged". Now back to the initial paragraph:
there is a single untagged VID that the driver keeps track of, and that
has just changed from 1 (the pvid) to 0. So this breaks the bridge
core's expectation, because it has changed vid 1 from untagged to
tagged, when what the user sees is.

$ bridge vlan
port    vlan ids
swp0     1 PVID Egress Untagged

br0      1 PVID Egress Untagged

But curiously, instead of manifesting itself as "untagged and
pvid-tagged traffic gets sent as tagged on egress", the bug:

- is hidden when vlan_filtering=0
- manifests as dropped traffic when vlan_filtering=1, due to this setting:

if (port->vlan_aware && !port->vid)
/* If port is vlan-aware and tagged, drop untagged and priority
* tagged frames.
*/
val |= ANA_PORT_DROP_CFG_DROP_UNTAGGED_ENA |
       ANA_PORT_DROP_CFG_DROP_PRIO_S_TAGGED_ENA |
       ANA_PORT_DROP_CFG_DROP_PRIO_C_TAGGED_ENA;

which would have made sense if it weren't for this bug. The setting's
intention was "this is a trunk port with no native VLAN, so don't accept
untagged traffic". So the driver was never expecting to set VLAN 0 as
the value of the native VLAN, 0 was just encoding for "invalid".

So the fix is to not send 802.1p traffic as untagged, because that would
change the port's native vlan to 0, unbeknownst to the bridge, and
trigger unexpected code paths in the driver.

Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fixes: 7142529f1688 ("net: mscc: ocelot: add VLAN filtering")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

wimax: i2400: Fix memory leak in i2400m_op_rfkill_sw_toggle

In the implementation of i2400m_op_rfkill_sw_toggle() the allocated
buffer for cmd should be released before returning. The
documentation for i2400m_msg_to_dev() says when it returns the buffer
can be reused. Meaning cmd should be released in either case. Move
kfree(cmd) before return to be reached by all execution paths.

Fixes: 2507e6ab7a9a ("wimax: i2400: fix memory leak")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hisilicon: Fix "Trying to free already-free IRQ"

When rmmod hip04_eth.ko, we can get the following warning:

Task track: rmmod(1623)>bash(1591)>login(1581)>init(1)
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1623 at kernel/irq/manage.c:1557 __free_irq+0xa4/0x2ac()
Trying to free already-free IRQ 200
Modules linked in: ping(O) pramdisk(O) cpuinfo(O) rtos_snapshot(O) interrupt_ctrl(O) mtdblock mtd_blkdevrtfs nfs_acl nfs lockd grace sunrpc xt_tcpudp ipt_REJECT iptable_filter ip_tables x_tables nf_reject_ipv
CPU: 0 PID: 1623 Comm: rmmod Tainted: G O 4.4.193 #1
Hardware name: Hisilicon A15
[<c020b408>] (rtos_unwind_backtrace) from [<c0206624>] (show_stack+0x10/0x14)
[<c0206624>] (show_stack) from [<c03f2be4>] (dump_stack+0xa0/0xd8)
[<c03f2be4>] (dump_stack) from [<c021a780>] (warn_slowpath_common+0x84/0xb0)
[<c021a780>] (warn_slowpath_common) from [<c021a7e8>] (warn_slowpath_fmt+0x3c/0x68)
[<c021a7e8>] (warn_slowpath_fmt) from [<c026876c>] (__free_irq+0xa4/0x2ac)
[<c026876c>] (__free_irq) from [<c0268a14>] (free_irq+0x60/0x7c)
[<c0268a14>] (free_irq) from [<c0469e80>] (release_nodes+0x1c4/0x1ec)
[<c0469e80>] (release_nodes) from [<c0466924>] (__device_release_driver+0xa8/0x104)
[<c0466924>] (__device_release_driver) from [<c0466a80>] (driver_detach+0xd0/0xf8)
[<c0466a80>] (driver_detach) from [<c0465e18>] (bus_remove_driver+0x64/0x8c)
[<c0465e18>] (bus_remove_driver) from [<c02935b0>] (SyS_delete_module+0x198/0x1e0)
[<c02935b0>] (SyS_delete_module) from [<c0202ed0>] (__sys_trace_return+0x0/0x10)
---[ end trace bb25d6123d849b44 ]---

Currently "rmmod hip04_eth.ko" call free_irq more than once
as devres_release_all and hip04_remove both call free_irq.
This results in a 'Trying to free already-free IRQ' warning.
To solve the problem free_irq has been moved out of hip04_remove.

Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fjes: Handle workqueue allocation failure

In the highly unlikely event that we fail to allocate either of the
"/txrx" or "/control" workqueues, we should bail cleanly rather than
blindly march on with NULL queue pointer(s) installed in the
'fjes_adapter' instance.

Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Nicolas Waisman <nico@semmle.com>
Link: https://lore.kernel.org/lkml/CADJ_3a8WFrs5NouXNqS5WYe7rebFP+_A5CheeqAyD_p7DFJJcg@mail.gmail.com/
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'batadv-net-for-davem-20191025' of git://git.open-mesh.org/linux-merge

Simon Wunderlich says:

====================
Here are two batman-adv bugfixes:

* Fix free/alloc race for OGM and OGMv2, by Sven Eckelmann (2 patches)
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: usb: lan78xx: Disable interrupts before calling generic_handle_irq()

lan78xx_status() will run with interrupts enabled due to the change in
ed194d136769 ("usb: core: remove local_irq_save() around ->complete()
handler"). generic_handle_irq() expects to be run with IRQs disabled.

[    4.886203] 000: irq 79 handler irq_default_primary_handler+0x0/0x8 enabled interrupts
[    4.886243] 000: WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:152 __handle_irq_event_percpu+0x154/0x168
[    4.896294] 000: Modules linked in:
[    4.896301] 000: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.6 #39
[    4.896310] 000: Hardware name: Raspberry Pi 3 Model B+ (DT)
[    4.896315] 000: pstate: 60000005 (nZCv daif -PAN -UAO)
[    4.896321] 000: pc : __handle_irq_event_percpu+0x154/0x168
[    4.896331] 000: lr : __handle_irq_event_percpu+0x154/0x168
[    4.896339] 000: sp : ffff000010003cc0
[    4.896346] 000: x29: ffff000010003cc0 x28: 0000000000000060
[    4.896355] 000: x27: ffff000011021980 x26: ffff00001189c72b
[    4.896364] 000: x25: ffff000011702bc0 x24: ffff800036d6e400
[    4.896373] 000: x23: 000000000000004f x22: ffff000010003d64
[    4.896381] 000: x21: 0000000000000000 x20: 0000000000000002
[    4.896390] 000: x19: ffff8000371c8480 x18: 0000000000000060
[    4.896398] 000: x17: 0000000000000000 x16: 00000000000000eb
[    4.896406] 000: x15: ffff000011712d18 x14: 7265746e69206465
[    4.896414] 000: x13: ffff000010003ba0 x12: ffff000011712df0
[    4.896422] 000: x11: 0000000000000001 x10: ffff000011712e08
[    4.896430] 000: x9 : 0000000000000001 x8 : 000000000003c920
[    4.896437] 000: x7 : ffff0000118cc410 x6 : ffff0000118c7f00
[    4.896445] 000: x5 : 000000000003c920 x4 : 0000000000004510
[    4.896453] 000: x3 : ffff000011712dc8 x2 : 0000000000000000
[    4.896461] 000: x1 : 73a3f67df94c1500 x0 : 0000000000000000
[    4.896466] 000: Call trace:
[    4.896471] 000:  __handle_irq_event_percpu+0x154/0x168
[    4.896481] 000:  handle_irq_event_percpu+0x50/0xb0
[    4.896489] 000:  handle_irq_event+0x40/0x98
[    4.896497] 000:  handle_simple_irq+0xa4/0xf0
[    4.896505] 000:  generic_handle_irq+0x24/0x38
[    4.896513] 000:  intr_complete+0xb0/0xe0
[    4.896525] 000:  __usb_hcd_giveback_urb+0x58/0xd8
[    4.896533] 000:  usb_giveback_urb_bh+0xd0/0x170
[    4.896539] 000:  tasklet_action_common.isra.0+0x9c/0x128
[    4.896549] 000:  tasklet_hi_action+0x24/0x30
[    4.896556] 000:  __do_softirq+0x120/0x23c
[    4.896564] 000:  irq_exit+0xb8/0xd8
[    4.896571] 000:  __handle_domain_irq+0x64/0xb8
[    4.896579] 000:  bcm2836_arm_irqchip_handle_irq+0x60/0xc0
[    4.896586] 000:  el1_irq+0xb8/0x140
[    4.896592] 000:  arch_cpu_idle+0x10/0x18
[    4.896601] 000:  do_idle+0x200/0x280
[    4.896608] 000:  cpu_startup_entry+0x20/0x28
[    4.896615] 000:  rest_init+0xb4/0xc0
[    4.896623] 000:  arch_call_rest_init+0xc/0x14
[    4.896632] 000:  start_kernel+0x454/0x480

Fixes: ed194d136769 ("usb: core: remove local_irq_save() around ->complete() handler")
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Stefan Wahren <wahrenst@gmx.net>
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Tested-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: improve NET_DSA_SJA1105_TAS dependency

An earlier bugfix introduced a dependency on CONFIG_NET_SCH_TAPRIO,
but this missed the case of NET_SCH_TAPRIO=m and NET_DSA_SJA1105=y,
which still causes a link error:

drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_setup_tc_taprio':
sja1105_tas.c:(.text+0x5c): undefined reference to `taprio_offload_free'
sja1105_tas.c:(.text+0x3b4): undefined reference to `taprio_offload_get'
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_tas_teardown':
sja1105_tas.c:(.text+0x6ec): undefined reference to `taprio_offload_free'

Change the dependency to only allow selecting the TAS code when it
can link against the taprio code.

Fixes: a8d570de0cc6 ("net: dsa: sja1105: Add dependency for NET_DSA_SJA1105_TAS")
Fixes: 317ab5b86c8e ("net: dsa: sja1105: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: ftgmac100: Fix DMA coherency issue with SW checksum

We are calling the checksum helper after the dma_map_single()
call to map the packet. This is incorrect as the checksumming
code will touch the packet from the CPU. This means the cache
won't be properly flushes (or the bounce buffering will leave
us with the unmodified packet to DMA).

This moves the calculation of the checksum & vlan tags to
before the DMA mapping.

This also has the side effect of fixing another bug: If the
checksum helper fails, we goto "drop" to drop the packet, which
will not unmap the DMA mapping.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes: 05690d633f30 ("ftgmac100: Upgrade to NETIF_F_HW_CSUM")
Reviewed-by: Vijay Khemka <vijaykhemka@fb.com>
Tested-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix sk_page_frag() recursion from memory reclaim

sk_page_frag() optimizes skb_frag allocations by using per-task
skb_frag cache when it knows it's the only user.  The condition is
determined by seeing whether the socket allocation mask allows
blocking - if the allocation may block, it obviously owns the task's
context and ergo exclusively owns current->task_frag.

Unfortunately, this misses recursion through memory reclaim path.
Please take a look at the following backtrace.

[2] RIP: 0010:tcp_sendmsg_locked+0xccf/0xe10
     ...
     tcp_sendmsg+0x27/0x40
     sock_sendmsg+0x30/0x40
     sock_xmit.isra.24+0xa1/0x170 [nbd]
     nbd_send_cmd+0x1d2/0x690 [nbd]
     nbd_queue_rq+0x1b5/0x3b0 [nbd]
     __blk_mq_try_issue_directly+0x108/0x1b0
     blk_mq_request_issue_directly+0xbd/0xe0
     blk_mq_try_issue_list_directly+0x41/0xb0
     blk_mq_sched_insert_requests+0xa2/0xe0
     blk_mq_flush_plug_list+0x205/0x2a0
     blk_flush_plug_list+0xc3/0xf0
[1] blk_finish_plug+0x21/0x2e
     _xfs_buf_ioapply+0x313/0x460
     __xfs_buf_submit+0x67/0x220
     xfs_buf_read_map+0x113/0x1a0
     xfs_trans_read_buf_map+0xbf/0x330
     xfs_btree_read_buf_block.constprop.42+0x95/0xd0
     xfs_btree_lookup_get_block+0x95/0x170
     xfs_btree_lookup+0xcc/0x470
     xfs_bmap_del_extent_real+0x254/0x9a0
     __xfs_bunmapi+0x45c/0xab0
     xfs_bunmapi+0x15/0x30
     xfs_itruncate_extents_flags+0xca/0x250
     xfs_free_eofblocks+0x181/0x1e0
     xfs_fs_destroy_inode+0xa8/0x1b0
     destroy_inode+0x38/0x70
     dispose_list+0x35/0x50
     prune_icache_sb+0x52/0x70
     super_cache_scan+0x120/0x1a0
     do_shrink_slab+0x120/0x290
     shrink_slab+0x216/0x2b0
     shrink_node+0x1b6/0x4a0
     do_try_to_free_pages+0xc6/0x370
     try_to_free_mem_cgroup_pages+0xe3/0x1e0
     try_charge+0x29e/0x790
     mem_cgroup_charge_skmem+0x6a/0x100
     __sk_mem_raise_allocated+0x18e/0x390
     __sk_mem_schedule+0x2a/0x40
[0] tcp_sendmsg_locked+0x8eb/0xe10
     tcp_sendmsg+0x27/0x40
     sock_sendmsg+0x30/0x40
     ___sys_sendmsg+0x26d/0x2b0
     __sys_sendmsg+0x57/0xa0
     do_syscall_64+0x42/0x100
     entry_SYSCALL_64_after_hwframe+0x44/0xa9

In [0], tcp_send_msg_locked() was using current->page_frag when it
called sk_wmem_schedule().  It already calculated how many bytes can
be fit into current->page_frag.  Due to memory pressure,
sk_wmem_schedule() called into memory reclaim path which called into
xfs and then IO issue path.  Because the filesystem in question is
backed by nbd, the control goes back into the tcp layer - back into
tcp_sendmsg_locked().

nbd sets sk_allocation to (GFP_NOIO | __GFP_MEMALLOC) which makes
sense - it's in the process of freeing memory and wants to be able to,
e.g., drop clean pages to make forward progress.  However, this
confused sk_page_frag() called from [2].  Because it only tests
whether the allocation allows blocking which it does, it now thinks
current->page_frag can be used again although it already was being
used in [0].

After [2] used current->page_frag, the offset would be increased by
the used amount.  When the control returns to [0],
current->page_frag's offset is increased and the previously calculated
number of bytes now may overrun the end of allocated memory leading to
silent memory corruptions.

Fix it by adding gfpflags_normal_context() which tests sleepable &&
!reclaim and use it to determine whether to use current->task_frag.

v2: Eric didn't like gfp flags being tested twice.  Introduce a new
    helper gfpflags_normal_context() and combine the two tests.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

udp: fix data-race in udp_set_dev_scratch()

KCSAN reported a data-race in udp_set_dev_scratch() [1]

The issue here is that we must not write over skb fields
if skb is shared. A similar issue has been fixed in commit
89c22d8c3b27 ("net: Fix skb csum races when peeking")

While we are at it, use a helper only dealing with
udp_skb_scratch(skb)->csum_unnecessary, as this allows
udp_set_dev_scratch() to be called once and thus inlined.

[1]
BUG: KCSAN: data-race in udp_set_dev_scratch / udpv6_recvmsg

write to 0xffff888120278317 of 1 bytes by task 10411 on cpu 1:
udp_set_dev_scratch+0xea/0x200 net/ipv4/udp.c:1308
__first_packet_length+0x147/0x420 net/ipv4/udp.c:1556
first_packet_length+0x68/0x2a0 net/ipv4/udp.c:1579
udp_poll+0xea/0x110 net/ipv4/udp.c:2720
sock_poll+0xed/0x250 net/socket.c:1256
vfs_poll include/linux/poll.h:90 [inline]
do_select+0x7d0/0x1020 fs/select.c:534
core_sys_select+0x381/0x550 fs/select.c:677
do_pselect.constprop.0+0x11d/0x160 fs/select.c:759
__do_sys_pselect6 fs/select.c:784 [inline]
__se_sys_pselect6 fs/select.c:769 [inline]
__x64_sys_pselect6+0x12e/0x170 fs/select.c:769
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9

read to 0xffff888120278317 of 1 bytes by task 10413 on cpu 0:
udp_skb_csum_unnecessary include/net/udp.h:358 [inline]
udpv6_recvmsg+0x43e/0xe90 net/ipv6/udp.c:310
inet6_recvmsg+0xbb/0x240 net/ipv6/af_inet6.c:592
sock_recvmsg_nosec+0x5c/0x70 net/socket.c:871
___sys_recvmsg+0x1a0/0x3e0 net/socket.c:2480
do_recvmmsg+0x19a/0x5c0 net/socket.c:2601
__sys_recvmmsg+0x1ef/0x200 net/socket.c:2680
__do_sys_recvmmsg net/socket.c:2703 [inline]
__se_sys_recvmmsg net/socket.c:2696 [inline]
__x64_sys_recvmmsg+0x89/0xb0 net/socket.c:2696
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 10413 Comm: syz-executor.0 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 2276f58ac589 ("udp: use a separate rx queue for packet reception")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dpaa2: Use the correct style for SPDX License Identifier

This patch corrects the SPDX License Identifier style in
header files related to DPAA2 Ethernet driver supporting
Freescale SoCs with DPAA2. For C header files
Documentation/process/license-rules.rst mandates C-like comments
(opposed to C source files where C++ style should be used)

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.

Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-avoid-KCSAN-splats'

Eric Dumazet says:

====================
net: avoid KCSAN splats

Often times we use skb_queue_empty() without holding a lock,
meaning that other cpus (or interrupt) can change the queue
under us. This is fine, but we need to properly annotate
the lockless intent to make sure the compiler wont over
optimize things.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: add READ_ONCE() annotation in __skb_wait_for_more_packets()

__skb_wait_for_more_packets() can be called while other cpus
can feed packets to the socket receive queue.

KCSAN reported :

BUG: KCSAN: data-race in __skb_wait_for_more_packets / __udp_enqueue_schedule_skb

write to 0xffff888102e40b58 of 8 bytes by interrupt on cpu 0:
__skb_insert include/linux/skbuff.h:1852 [inline]
__skb_queue_before include/linux/skbuff.h:1958 [inline]
__skb_queue_tail include/linux/skbuff.h:1991 [inline]
__udp_enqueue_schedule_skb+0x2d7/0x410 net/ipv4/udp.c:1470
__udp_queue_rcv_skb net/ipv4/udp.c:1940 [inline]
udp_queue_rcv_one_skb+0x7bd/0xc70 net/ipv4/udp.c:2057
udp_queue_rcv_skb+0xb5/0x400 net/ipv4/udp.c:2074
udp_unicast_rcv_skb.isra.0+0x7e/0x1c0 net/ipv4/udp.c:2233
__udp4_lib_rcv+0xa44/0x17c0 net/ipv4/udp.c:2300
udp_rcv+0x2b/0x40 net/ipv4/udp.c:2470
ip_protocol_deliver_rcu+0x4d/0x420 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5010
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5124
process_backlog+0x1d3/0x420 net/core/dev.c:5955

read to 0xffff888102e40b58 of 8 bytes by task 13035 on cpu 1:
__skb_wait_for_more_packets+0xfa/0x320 net/core/datagram.c:100
__skb_recv_udp+0x374/0x500 net/ipv4/udp.c:1683
udp_recvmsg+0xe1/0xb10 net/ipv4/udp.c:1712
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec+0x5c/0x70 net/socket.c:871
___sys_recvmsg+0x1a0/0x3e0 net/socket.c:2480
do_recvmmsg+0x19a/0x5c0 net/socket.c:2601
__sys_recvmmsg+0x1ef/0x200 net/socket.c:2680
__do_sys_recvmmsg net/socket.c:2703 [inline]
__se_sys_recvmmsg net/socket.c:2696 [inline]
__x64_sys_recvmmsg+0x89/0xb0 net/socket.c:2696
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 13035 Comm: syz-executor.3 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: use skb_queue_empty_lockless() in busy poll contexts

Busy polling usually runs without locks.
Let's use skb_queue_empty_lockless() instead of skb_queue_empty()

Also uses READ_ONCE() in __skb_try_recv_datagram() to address
a similar potential problem.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: use skb_queue_empty_lockless() in poll() handlers

Many poll() handlers are lockless. Using skb_queue_empty_lockless()
instead of skb_queue_empty() is more appropriate.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

udp: use skb_queue_empty_lockless()

syzbot reported a data-race [1].

We should use skb_queue_empty_lockless() to document that we are
not ensuring a mutual exclusion and silence KCSAN.

[1]
BUG: KCSAN: data-race in __skb_recv_udp / __udp_enqueue_schedule_skb

write to 0xffff888122474b50 of 8 bytes by interrupt on cpu 0:
__skb_insert include/linux/skbuff.h:1852 [inline]
__skb_queue_before include/linux/skbuff.h:1958 [inline]
__skb_queue_tail include/linux/skbuff.h:1991 [inline]
__udp_enqueue_schedule_skb+0x2c1/0x410 net/ipv4/udp.c:1470
__udp_queue_rcv_skb net/ipv4/udp.c:1940 [inline]
udp_queue_rcv_one_skb+0x7bd/0xc70 net/ipv4/udp.c:2057
udp_queue_rcv_skb+0xb5/0x400 net/ipv4/udp.c:2074
udp_unicast_rcv_skb.isra.0+0x7e/0x1c0 net/ipv4/udp.c:2233
__udp4_lib_rcv+0xa44/0x17c0 net/ipv4/udp.c:2300
udp_rcv+0x2b/0x40 net/ipv4/udp.c:2470
ip_protocol_deliver_rcu+0x4d/0x420 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5010
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5124
process_backlog+0x1d3/0x420 net/core/dev.c:5955

read to 0xffff888122474b50 of 8 bytes by task 8921 on cpu 1:
skb_queue_empty include/linux/skbuff.h:1494 [inline]
__skb_recv_udp+0x18d/0x500 net/ipv4/udp.c:1653
udp_recvmsg+0xe1/0xb10 net/ipv4/udp.c:1712
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec+0x5c/0x70 net/socket.c:871
___sys_recvmsg+0x1a0/0x3e0 net/socket.c:2480
do_recvmmsg+0x19a/0x5c0 net/socket.c:2601
__sys_recvmmsg+0x1ef/0x200 net/socket.c:2680
__do_sys_recvmmsg net/socket.c:2703 [inline]
__se_sys_recvmmsg net/socket.c:2696 [inline]
__x64_sys_recvmmsg+0x89/0xb0 net/socket.c:2696
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 8921 Comm: syz-executor.4 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: add skb_queue_empty_lockless()

Some paths call skb_queue_empty() without holding
the queue lock. We must use a barrier in order
to not let the compiler do strange things, and avoid
KCSAN splats.

Adding a barrier in skb_queue_empty() might be overkill,
I prefer adding a new helper to clearly identify
points where the callers might be lockless. This might
help us finding real bugs.

The corresponding WRITE_ONCE() should add zero cost
for current compilers.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./pub/scm/linux/kernel/git/pablo/nf

Pablo Neira Ayuso says:

====================
Netfilter/IPVS fixes for net

The following patchset contains Netfilter/IPVS fixes for net:

1) Fix crash on flowtable due to race between garbage collection
and insertion.

2) Restore callback unbinding in netfilter offloads.

3) Fix races on IPVS module removal, from Davide Caratti.

4) Make old_secure_tcp per-netns to fix sysbot report,
from Eric Dumazet.

5) Validate matching length in netfilter offloads, from wenxu.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./pub/scm/linux/kernel/git/bpf/bpf

Daniel Borkmann says:

====================
pull-request: bpf 2019-10-27

The following pull-request contains BPF updates for your *net* tree.

We've added 7 non-merge commits during the last 11 day(s) which contain
a total of 7 files changed, 66 insertions(+), 16 deletions(-).

The main changes are:

1) Fix two use-after-free bugs in relation to RCU in jited symbol exposure to
   kallsyms, from Daniel Borkmann.

2) Fix NULL pointer dereference in AF_XDP rx-only sockets, from Magnus Karlsson.

3) Fix hang in netdev unregister for hash based devmap as well as another overflow
   bug on 32 bit archs in memlock cost calculation, from Toke Høiland-Jørgensen.

4) Fix wrong memory access in LWT BPF programs on reroute due to invalid dst.
   Also fix BPF selftests to use more compatible nc options, from Jiri Benc.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'ipv4-fix-route-update-on-metric-change'

Paolo Abeni says:

====================
ipv4: fix route update on metric change.

This fixes connected route update on some edge cases for ip addr metric
change.
It additionally includes self tests for the covered scenarios. The new tests
fail on unpatched kernels and pass on the patched one.

v1 -> v2:
- add selftests
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: fib_tests: add more tests for metric update

This patch adds two more tests to ipv4_addr_metric_test() to
explicitly cover the scenarios fixed by the previous patch.

Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: fix route update on metric change.

Since commit af4d768ad28c ("net/ipv4: Add support for specifying metric
of connected routes"), when updating an IP address with a different metric,
the associated connected route is updated, too.

Still, the mentioned commit doesn't handle properly some corner cases:

$ ip addr add dev eth0 192.168.1.0/24
$ ip addr add dev eth0 192.168.2.1/32 peer 192.168.2.2
$ ip addr add dev eth0 192.168.3.1/24
$ ip addr change dev eth0 192.168.1.0/24 metric 10
$ ip addr change dev eth0 192.168.2.1/32 peer 192.168.2.2 metric 10
$ ip addr change dev eth0 192.168.3.1/24 metric 10
$ ip -4 route
192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.0
192.168.2.2 dev eth0 proto kernel scope link src 192.168.2.1
192.168.3.0/24 dev eth0 proto kernel scope link src 192.168.2.1 metric 10

Only the last route is correctly updated.

The problem is the current test in fib_modify_prefix_metric():

if (!(dev->flags & IFF_UP) ||
    ifa->ifa_flags & (IFA_F_SECONDARY | IFA_F_NOPREFIXROUTE) ||
    ipv4_is_zeronet(prefix) ||
    prefix == ifa->ifa_local || ifa->ifa_prefixlen == 32)

Which should be the logical 'not' of the pre-existing test in
fib_add_ifaddr():

if (!ipv4_is_zeronet(prefix) && !(ifa->ifa_flags & IFA_F_SECONDARY) &&
    (prefix != addr || ifa->ifa_prefixlen < 32))

To properly negate the original expression, we need to change the last
logical 'or' to a logical 'and'.

Fixes: af4d768ad28c ("net/ipv4: Add support for specifying metric of connected routes")
Reported-and-suggested-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Zeroing the structure ethtool_wolinfo in ethtool_get_wol()

memset() the structure ethtool_wolinfo that has padded bytes
but the padded bytes have not been zeroed out.

Signed-off-by: zhanglin <zhang.lin16@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'ipvs-fixes-for-v5.4' of https://git./linux/kernel/git/horms/ipvs

Simon Horman says:

====================
IPVS fixes for v5.4

* Eric Dumazet resolves a race condition in switching the defense level
* Davide Caratti resolves a race condition in module removal
====================

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

cxgb4: request the TX CIDX updates to status page

For adapters which support the SGE Doorbell Queue Timer facility,
we configured the Ethernet TX Queues to send CIDX Updates to the
Associated Ethernet RX Response Queue with CPL_SGE_EGR_UPDATE
messages to allow us to respond more quickly to the CIDX Updates.
But, this was adding load to PCIe Link RX bandwidth and,
potentially, resulting in higher CPU Interrupt load.

This patch requests the HW to deliver the CIDX updates to the TX
queue status page rather than generating an ingress queue message
(as an interrupt). With this patch, the load on RX bandwidth is
reduced and a substantial improvement in BW is noticed at lower
IO sizes.

Fixes: d429005fdf2c ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netns: fix GFP flags in rtnl_net_notifyid()

In rtnl_net_notifyid(), we certainly can't pass a null GFP flag to
rtnl_notify(). A GFP_KERNEL flag would be fine in most circumstances,
but there are a few paths calling rtnl_net_notifyid() from atomic
context or from RCU critical sections. The later also precludes the use
of gfp_any() as it wouldn't detect the RCU case. Also, the nlmsg_new()
call is wrong too, as it uses GFP_KERNEL unconditionally.

Therefore, we need to pass the GFP flags as parameter and propagate it
through function calls until the proper flags can be determined.

In most cases, GFP_KERNEL is fine. The exceptions are:
  * openvswitch: ovs_vport_cmd_get() and ovs_vport_cmd_dump()
    indirectly call rtnl_net_notifyid() from RCU critical section,

  * rtnetlink: rtmsg_ifinfo_build_skb() already receives GFP flags as
    parameter.

Also, in ovs_vport_cmd_build_info(), let's change the GFP flags used
by nlmsg_new(). The function is allowed to sleep, so better make the
flags consistent with the ones used in the following
ovs_vport_cmd_fill_info() call.

Found by code inspection.

Fixes: 9a9634545c70 ("netns: notify netns id events")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: Use the correct style for SPDX License Identifier

This patch corrects the SPDX License Identifier style in
header file related to ethernet driver for Cortina Gemini
devices. For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.

Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'smc-fixes'

Karsten Graul says:

====================
net/smc: fixes for -net

Fixes for the net tree, covering a memleak when closing
SMC fallback sockets and fix SMC-R connection establishment
when vlan-ids are used.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net/smc: keep vlan_id for SMC-R in smc_listen_work()

Creating of an SMC-R connection with vlan-id fails, because
smc_listen_work() determines the vlan_id of the connection,
saves it in struct smc_init_info ini, but clears the ini area
again if SMC-D is not applicable.
This patch just resets the ISM device before investigating
SMC-R availability.

Fixes: bc36d2fc93eb ("net/smc: consolidate function parameters")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/smc: fix closing of fallback SMC sockets

For SMC sockets forced to fallback to TCP, the file is propagated
from the outer SMC to the internal TCP socket. When closing the SMC
socket, the internal TCP socket file pointer must be restored to the
original NULL value, otherwise memory leaks may show up (found with
CONFIG_DEBUG_KMEMLEAK).

The internal TCP socket is released in smc_clcsock_release(), which
calls __sock_release() function in net/socket.c. This calls the
needed iput(SOCK_INODE(sock)) only, if the file pointer has been reset
to the original NULL-value.

Fixes: 07603b230895 ("net/smc: propagate file from SMC to TCP socket")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hwbm: if CONFIG_NET_HWBM unset, make stub functions static

If CONFIG_NET_HWBM is not set, then these stub functions in
<net/hwbm.h> should be declared static to avoid trying to
export them from any driver that includes this.

Fixes the following sparse warnings:

./include/net/hwbm.h:24:6: warning: symbol 'hwbm_buf_free' was not declared. Should it be static?
./include/net/hwbm.h:25:5: warning: symbol 'hwbm_pool_refill' was not declared. Should it be static?
./include/net/hwbm.h:26:5: warning: symbol 'hwbm_pool_add' was not declared. Should it be static?

Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mvneta: make stub functions static inline

If the CONFIG_MVNET_BA is not set, then make the stub functions
static inline to avoid trying to export them, and remove hte
following sparse warnings:

drivers/net/ethernet/marvell/mvneta_bm.h:163:6: warning: symbol 'mvneta_bm_pool_destroy' was not declared. Should it be static?
drivers/net/ethernet/marvell/mvneta_bm.h:165:6: warning: symbol 'mvneta_bm_bufs_free' was not declared. Should it be static?
drivers/net/ethernet/marvell/mvneta_bm.h:167:5: warning: symbol 'mvneta_bm_construct' was not declared. Should it be static?
drivers/net/ethernet/marvell/mvneta_bm.h:168:5: warning: symbol 'mvneta_bm_pool_refill' was not declared. Should it be static?
drivers/net/ethernet/marvell/mvneta_bm.h:170:23: warning: symbol 'mvneta_bm_pool_use' was not declared. Should it be static?
drivers/net/ethernet/marvell/mvneta_bm.h:181:18: warning: symbol 'mvneta_bm_get' was not declared. Should it be static?
drivers/net/ethernet/marvell/mvneta_bm.h:182:6: warning: symbol 'mvneta_bm_put' was not declared. Should it be static?

Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sch_generic: Use pfifo_fast as fallback scheduler for CAN hardware

There is networking hardware that isn't based on Ethernet for layers 1 and 2.

For example CAN.

CAN is a multi-master serial bus standard for connecting Electronic Control
Units [ECUs] also known as nodes. A frame on the CAN bus carries up to 8 bytes
of payload. Frame corruption is detected by a CRC. However frame loss due to
corruption is possible, but a quite unusual phenomenon.

While fq_codel works great for TCP/IP, it doesn't for CAN. There are a lot of
legacy protocols on top of CAN, which are not build with flow control or high
CAN frame drop rates in mind.

When using fq_codel, as soon as the queue reaches a certain delay based length,
skbs from the head of the queue are silently dropped. Silently meaning that the
user space using a send() or similar syscall doesn't get an error. However
TCP's flow control algorithm will detect dropped packages and adjust the
bandwidth accordingly.

When using fq_codel and sending raw frames over CAN, which is the common use
case, the user space thinks the package has been sent without problems, because
send() returned without an error. pfifo_fast will drop skbs, if the queue
length exceeds the maximum. But with this scheduler the skbs at the tail are
dropped, an error (-ENOBUFS) is propagated to user space. So that the user
space can slow down the package generation.

On distributions, where fq_codel is made default via CONFIG_DEFAULT_NET_SCH
during compile time, or set default during runtime with sysctl
net.core.default_qdisc (see [1]), we get a bad user experience. In my test case
with pfifo_fast, I can transfer thousands of million CAN frames without a frame
drop. On the other hand with fq_codel there is more then one lost CAN frame per
thousand frames.

As pointed out fq_codel is not suited for CAN hardware, so this patch changes
attach_one_default_qdisc() to use pfifo_fast for "ARPHRD_CAN" network devices.

During transition of a netdev from down to up state the default queuing
discipline is attached by attach_default_qdiscs() with the help of
attach_one_default_qdisc(). This patch modifies attach_one_default_qdisc() to
attach the pfifo_fast (pfifo_fast_ops) if the network device type is
"ARPHRD_CAN".

[1] https://github.com/systemd/systemd/issues/9194

Signed-off-by: Vincent Prince <vincent.prince.fr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-fix-nested-device-bugs'

Taehee Yoo says:

====================
net: fix nested device bugs

This patchset fixes several bugs that are related to nesting
device infrastructure.
Current nesting infrastructure code doesn't limit the depth level of
devices. nested devices could be handled recursively. at that moment,
it needs huge memory and stack overflow could occur.
Below devices type have same bug.
VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, and VXLAN.
But I couldn't test all interface types so there could be more device
types, which have similar problems.
Maybe qmi_wwan.c code could have same problem.
So, I would appreciate if someone test qmi_wwan.c and other modules.

Test commands:
    ip link add dummy0 type dummy
    ip link add vlan1 link dummy0 type vlan id 1

    for i in {2..100}
    do
    let A=$i-1
    ip link add name vlan$i link vlan$A type vlan id $i
    done
    ip link del dummy0

1st patch actually fixes the root cause.
It adds new common variables {upper/lower}_level that represent
depth level. upper_level variable is depth of upper devices.
lower_level variable is depth of lower devices.

      [U][L]       [U][L]
vlan1  1  5  vlan4  1  4
vlan2  2  4  vlan5  2  3
vlan3  3  3    |
  |            |
  +------------+
  |
vlan6  4  2
dummy0 5  1

After this patch, the nesting infrastructure code uses this variable to
check the depth level.

2nd patch fixes Qdisc lockdep related problem.
Before this patch, devices use static lockdep map.
So, if devices that are same types are nested, lockdep will warn about
recursive situation.
These patches make these devices use dynamic lockdep key instead of
static lock or subclass.

3rd patch fixes unexpected IFF_BONDING bit unset.
When nested bonding interface scenario, bonding interface could lost it's
IFF_BONDING flag. This should not happen.
This patch adds a condition before unsetting IFF_BONDING.

4th patch fixes nested locking problem in bonding interface
Bonding interface has own lock and this uses static lock.
Bonding interface could be nested and it uses same lockdep key.
So that unexisting lockdep warning occurs.

5th patch fixes nested locking problem in team interface
Team interface has own lock and this uses static lock.
Team interface could be nested and it uses same lockdep key.
So that unexisting lockdep warning occurs.

6th patch fixes a refcnt leak in the macsec module.
When the macsec module is unloaded, refcnt leaks occur.
But actually, that holding refcnt is unnecessary.
So this patch just removes these code.

7th patch adds ignore flag to an adjacent structure.
In order to exchange an adjacent node safely, ignore flag is needed.

8th patch makes vxlan add an adjacent link to limit depth level.
Vxlan interface could set it's lower interface and these lower interfaces
are handled recursively.
So, if the depth of lower interfaces is too deep, stack overflow could
happen.

9th patch removes unnecessary variables and callback.
After 1st patch, subclass callback and variables are unnecessary.
This patch just removes these variables and callback.

10th patch fix refcnt leaks in the virt_wifi module
Like every nested interface, the upper interface should be deleted
before the lower interface is deleted.
In order to fix this, the notifier routine is added in this patch.

v4 -> v5 :
- Update log messages
- Move variables position, 1st patch
- Fix iterator routine, 1st patch
- Add generic lockdep key code, which replaces 2, 4, 5, 6, 7 patches.
- Log message update, 10th patch
- Fix wrong error value in error path of __init routine, 10th patch
- hold module refcnt when interface is created, 10th patch
v3 -> v4 :
- Add new 12th patch to fix refcnt leaks in the virt_wifi module
- Fix wrong usage netdev_upper_dev_link() in the vxlan.c
- Preserve reverse christmas tree variable ordering in the vxlan.c
- Add missing static keyword in the dev.c
- Expose netdev_adjacent_change_{prepare/commit/abort} instead of
   netdev_adjacent_dev_{enable/disable}
v2 -> v3 :
- Modify nesting infrastructure code to use iterator instead of recursive.
v1 -> v2 :
- Make the 3rd patch do not add a new priv_flag.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

virt_wifi: fix refcnt leak in module exit routine

virt_wifi_newlink() calls netdev_upper_dev_link() and it internally
holds reference count of lower interface.

Current code does not release a reference count of the lower interface
when the lower interface is being deleted.
So, reference count leaks occur.

Test commands:
    ip link add dummy0 type dummy
    ip link add vw1 link dummy0 type virt_wifi
    ip link del dummy0

Splat looks like:
[  133.787526][  T788] WARNING: CPU: 1 PID: 788 at net/core/dev.c:8274 rollback_registered_many+0x835/0xc80
[  133.788355][  T788] Modules linked in: virt_wifi cfg80211 dummy team af_packet sch_fq_codel ip_tables x_tables unix
[  133.789377][  T788] CPU: 1 PID: 788 Comm: ip Not tainted 5.4.0-rc3+ #96
[  133.790069][  T788] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[  133.791167][  T788] RIP: 0010:rollback_registered_many+0x835/0xc80
[  133.791906][  T788] Code: 00 4d 85 ff 0f 84 b5 fd ff ff ba c0 0c 00 00 48 89 de 4c 89 ff e8 9b 58 04 00 48 89 df e8 30
[  133.794317][  T788] RSP: 0018:ffff88805ba3f338 EFLAGS: 00010202
[  133.795080][  T788] RAX: ffff88805e57e801 RBX: ffff88805ba34000 RCX: ffffffffa9294723
[  133.796045][  T788] RDX: 1ffff1100b746816 RSI: 0000000000000008 RDI: ffffffffabcc4240
[  133.797006][  T788] RBP: ffff88805ba3f4c0 R08: fffffbfff5798849 R09: fffffbfff5798849
[  133.797993][  T788] R10: 0000000000000001 R11: fffffbfff5798848 R12: dffffc0000000000
[  133.802514][  T788] R13: ffff88805ba3f440 R14: ffff88805ba3f400 R15: ffff88805ed622c0
[  133.803237][  T788] FS:  00007f2e9608c0c0(0000) GS:ffff88806cc00000(0000) knlGS:0000000000000000
[  133.804002][  T788] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  133.804664][  T788] CR2: 00007f2e95610603 CR3: 000000005f68c004 CR4: 00000000000606e0
[  133.805363][  T788] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  133.806073][  T788] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  133.806787][  T788] Call Trace:
[  133.807069][  T788]  ? generic_xdp_install+0x310/0x310
[  133.807612][  T788]  ? lock_acquire+0x164/0x3b0
[  133.808077][  T788]  ? is_bpf_text_address+0x5/0xf0
[  133.808640][  T788]  ? deref_stack_reg+0x9c/0xd0
[  133.809138][  T788]  ? __nla_validate_parse+0x98/0x1ab0
[  133.809944][  T788]  unregister_netdevice_many.part.122+0x13/0x1b0
[  133.810599][  T788]  rtnl_delete_link+0xbc/0x100
[  133.811073][  T788]  ? rtnl_af_register+0xc0/0xc0
[  133.811672][  T788]  rtnl_dellink+0x30e/0x8a0
[  133.812205][  T788]  ? is_bpf_text_address+0x5/0xf0
[ ... ]

[  144.110530][  T788] unregister_netdevice: waiting for dummy0 to become free. Usage count = 1

This patch adds notifier routine to delete upper interface before deleting
lower interface.

Fixes: c7cdba31ed8b ("mac80211-next: rtnetlink wifi simulation device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: remove unnecessary variables and callback

This patch removes variables and callback these are related to the nested
device structure.
devices that can be nested have their own nest_level variable that
represents the depth of nested devices.
In the previous patch, new {lower/upper}_level variables are added and
they replace old private nest_level variable.
So, this patch removes all 'nest_level' variables.

In order to avoid lockdep warning, ->ndo_get_lock_subclass() was added
to get lockdep subclass value, which is actually lower nested depth value.
But now, they use the dynamic lockdep key to avoid lockdep warning instead
of the subclass.
So, this patch removes ->ndo_get_lock_subclass() callback.

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxlan: add adjacent link to limit depth level

Current vxlan code doesn't limit the number of nested devices.
Nested devices would be handled recursively and this routine needs
huge stack memory. So, unlimited nested devices could make
stack overflow.

In order to fix this issue, this patch adds adjacent links.
The adjacent link APIs internally check the depth level.

Test commands:
    ip link add dummy0 type dummy
    ip link add vxlan0 type vxlan id 0 group 239.1.1.1 dev dummy0 \
    dstport 4789
    for i in {1..100}
    do
    let A=$i-1
    ip link add vxlan$i type vxlan id $i group 239.1.1.1 \
    dev vxlan$A dstport 4789
    done
    ip link del dummy0

The top upper link is vxlan100 and the lowest link is vxlan0.
When vxlan0 is deleting, the upper devices will be deleted recursively.
It needs huge stack memory so it makes stack overflow.

Splat looks like:
[  229.628477] =============================================================================
[  229.629785] BUG page->ptl (Not tainted): Padding overwritten. 0x0000000026abf214-0x0000000091f6abb2
[  229.629785] -----------------------------------------------------------------------------
[  229.629785]
[  229.655439] ==================================================================
[  229.629785] INFO: Slab 0x00000000ff7cfda8 objects=19 used=19 fp=0x00000000fe33776c flags=0x200000000010200
[  229.655688] BUG: KASAN: stack-out-of-bounds in unmap_single_vma+0x25a/0x2e0
[  229.655688] Read of size 8 at addr ffff888113076928 by task vlan-network-in/2334
[  229.655688]
[  229.629785] Padding 0000000026abf214: 00 80 14 0d 81 88 ff ff 68 91 81 14 81 88 ff ff  ........h.......
[  229.629785] Padding 0000000001e24790: 38 91 81 14 81 88 ff ff 68 91 81 14 81 88 ff ff  8.......h.......
[  229.629785] Padding 00000000b39397c8: 33 30 62 a7 ff ff ff ff ff eb 60 22 10 f1 ff 1f  30b.......`"....
[  229.629785] Padding 00000000bc98f53a: 80 60 07 13 81 88 ff ff 00 80 14 0d 81 88 ff ff  .`..............
[  229.629785] Padding 000000002aa8123d: 68 91 81 14 81 88 ff ff f7 21 17 a7 ff ff ff ff  h........!......
[  229.629785] Padding 000000001c8c2369: 08 81 14 0d 81 88 ff ff 03 02 00 00 00 00 00 00  ................
[  229.629785] Padding 000000004e290c5d: 21 90 a2 21 10 ed ff ff 00 00 00 00 00 fc ff df  !..!............
[  229.629785] Padding 000000000e25d731: 18 60 07 13 81 88 ff ff c0 8b 13 05 81 88 ff ff  .`..............
[  229.629785] Padding 000000007adc7ab3: b3 8a b5 41 00 00 00 00                          ...A....
[  229.629785] FIX page->ptl: Restoring 0x0000000026abf214-0x0000000091f6abb2=0x5a
[  ... ]

Fixes: acaf4e70997f ("net: vxlan: when lower dev unregisters remove vxlan dev as well")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: core: add ignore flag to netdev_adjacent structure

In order to link an adjacent node, netdev_upper_dev_link() is used
and in order to unlink an adjacent node, netdev_upper_dev_unlink() is used.
unlink operation does not fail, but link operation can fail.

In order to exchange adjacent nodes, we should unlink an old adjacent
node first. then, link a new adjacent node.
If link operation is failed, we should link an old adjacent node again.
But this link operation can fail too.
It eventually breaks the adjacent link relationship.

This patch adds an ignore flag into the netdev_adjacent structure.
If this flag is set, netdev_upper_dev_link() ignores an old adjacent
node for a moment.

This patch also adds new functions for other modules.
netdev_adjacent_change_prepare()
netdev_adjacent_change_commit()
netdev_adjacent_change_abort()

netdev_adjacent_change_prepare() inserts new device into adjacent list
but new device is not allowed to use immediately.
If netdev_adjacent_change_prepare() fails, it internally rollbacks
adjacent list so that we don't need any other action.
netdev_adjacent_change_commit() deletes old device in the adjacent list
and allows new device to use.
netdev_adjacent_change_abort() rollbacks adjacent list.

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

macsec: fix refcnt leak in module exit routine

When a macsec interface is created, it increases a refcnt to a lower
device(real device). when macsec interface is deleted, the refcnt is
decreased in macsec_free_netdev(), which is ->priv_destructor() of
macsec interface.

The problem scenario is this.
When nested macsec interfaces are exiting, the exit routine of the
macsec module makes refcnt leaks.

Test commands:
    ip link add dummy0 type dummy
    ip link add macsec0 link dummy0 type macsec
    ip link add macsec1 link macsec0 type macsec
    modprobe -rv macsec

[  208.629433] unregister_netdevice: waiting for macsec0 to become free. Usage count = 1

Steps of exit routine of macsec module are below.
1. Calls ->dellink() in __rtnl_link_unregister().
2. Checks refcnt and wait refcnt to be 0 if refcnt is not 0 in
netdev_run_todo().
3. Calls ->priv_destruvtor() in netdev_run_todo().

Step2 checks refcnt, but step3 decreases refcnt.
So, step2 waits forever.

This patch makes the macsec module do not hold a refcnt of the lower
device because it already holds a refcnt of the lower device with
netdev_upper_dev_link().

Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

team: fix nested locking lockdep warning

team interface could be nested and it's lock variable could be nested too.
But this lock uses static lockdep key and there is no nested locking
handling code such as mutex_lock_nested() and so on.
so the Lockdep would warn about the circular locking scenario that
couldn't happen.
In order to fix, this patch makes the team module to use dynamic lock key
instead of static key.

Test commands:
    ip link add team0 type team
    ip link add team1 type team
    ip link set team0 master team1
    ip link set team0 nomaster
    ip link set team1 master team0
    ip link set team1 nomaster

Splat that looks like:
[   40.364352] WARNING: possible recursive locking detected
[   40.364964] 5.4.0-rc3+ #96 Not tainted
[   40.365405] --------------------------------------------
[   40.365973] ip/750 is trying to acquire lock:
[   40.366542] ffff888060b34c40 (&team->lock){+.+.}, at: team_set_mac_address+0x151/0x290 [team]
[   40.367689]
       but task is already holding lock:
[   40.368729] ffff888051201c40 (&team->lock){+.+.}, at: team_del_slave+0x29/0x60 [team]
[   40.370280]
       other info that might help us debug this:
[   40.371159]  Possible unsafe locking scenario:

[   40.371942]        CPU0
[   40.372338]        ----
[   40.372673]   lock(&team->lock);
[   40.373115]   lock(&team->lock);
[   40.373549]
       *** DEADLOCK ***

[   40.374432]  May be due to missing lock nesting notation

[   40.375338] 2 locks held by ip/750:
[   40.375851]  #0: ffffffffabcc42b0 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x466/0x8a0
[   40.376927]  #1: ffff888051201c40 (&team->lock){+.+.}, at: team_del_slave+0x29/0x60 [team]
[   40.377989]
       stack backtrace:
[   40.378650] CPU: 0 PID: 750 Comm: ip Not tainted 5.4.0-rc3+ #96
[   40.379368] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   40.380574] Call Trace:
[   40.381208]  dump_stack+0x7c/0xbb
[   40.381959]  __lock_acquire+0x269d/0x3de0
[   40.382817]  ? register_lock_class+0x14d0/0x14d0
[   40.383784]  ? check_chain_key+0x236/0x5d0
[   40.384518]  lock_acquire+0x164/0x3b0
[   40.385074]  ? team_set_mac_address+0x151/0x290 [team]
[   40.385805]  __mutex_lock+0x14d/0x14c0
[   40.386371]  ? team_set_mac_address+0x151/0x290 [team]
[   40.387038]  ? team_set_mac_address+0x151/0x290 [team]
[   40.387632]  ? mutex_lock_io_nested+0x1380/0x1380
[   40.388245]  ? team_del_slave+0x60/0x60 [team]
[   40.388752]  ? rcu_read_lock_sched_held+0x90/0xc0
[   40.389304]  ? rcu_read_lock_bh_held+0xa0/0xa0
[   40.389819]  ? lock_acquire+0x164/0x3b0
[   40.390285]  ? lockdep_rtnl_is_held+0x16/0x20
[   40.390797]  ? team_port_get_rtnl+0x90/0xe0 [team]
[   40.391353]  ? __module_text_address+0x13/0x140
[   40.391886]  ? team_set_mac_address+0x151/0x290 [team]
[   40.392547]  team_set_mac_address+0x151/0x290 [team]
[   40.393111]  dev_set_mac_address+0x1f0/0x3f0
[ ... ]

Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: use dynamic lockdep key instead of subclass

All bonding device has same lockdep key and subclass is initialized with
nest_level.
But actual nest_level value can be changed when a lower device is attached.
And at this moment, the subclass should be updated but it seems to be
unsafe.
So this patch makes bonding use dynamic lockdep key instead of the
subclass.

Test commands:
    ip link add bond0 type bond

    for i in {1..5}
    do
    let A=$i-1
    ip link add bond$i type bond
    ip link set bond$i master bond$A
    done
    ip link set bond5 master bond0

Splat looks like:
[  307.992912] WARNING: possible recursive locking detected
[  307.993656] 5.4.0-rc3+ #96 Tainted: G        W
[  307.994367] --------------------------------------------
[  307.995092] ip/761 is trying to acquire lock:
[  307.995710] ffff8880513aac60 (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0xb8/0x500 [bonding]
[  307.997045]
       but task is already holding lock:
[  307.997923] ffff88805fcbac60 (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0xb8/0x500 [bonding]
[  307.999215]
       other info that might help us debug this:
[  308.000251]  Possible unsafe locking scenario:

[  308.001137]        CPU0
[  308.001533]        ----
[  308.001915]   lock(&(&bond->stats_lock)->rlock#2/2);
[  308.002609]   lock(&(&bond->stats_lock)->rlock#2/2);
[  308.003302]
*** DEADLOCK ***

[  308.004310]  May be due to missing lock nesting notation

[  308.005319] 3 locks held by ip/761:
[  308.005830]  #0: ffffffff9fcc42b0 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x466/0x8a0
[  308.006894]  #1: ffff88805fcbac60 (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0xb8/0x500 [bonding]
[  308.008243]  #2: ffffffff9f9219c0 (rcu_read_lock){....}, at: bond_get_stats+0x9f/0x500 [bonding]
[  308.009422]
       stack backtrace:
[  308.010124] CPU: 0 PID: 761 Comm: ip Tainted: G        W         5.4.0-rc3+ #96
[  308.011097] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[  308.012179] Call Trace:
[  308.012601]  dump_stack+0x7c/0xbb
[  308.013089]  __lock_acquire+0x269d/0x3de0
[  308.013669]  ? register_lock_class+0x14d0/0x14d0
[  308.014318]  lock_acquire+0x164/0x3b0
[  308.014858]  ? bond_get_stats+0xb8/0x500 [bonding]
[  308.015520]  _raw_spin_lock_nested+0x2e/0x60
[  308.016129]  ? bond_get_stats+0xb8/0x500 [bonding]
[  308.017215]  bond_get_stats+0xb8/0x500 [bonding]
[  308.018454]  ? bond_arp_rcv+0xf10/0xf10 [bonding]
[  308.019710]  ? rcu_read_lock_held+0x90/0xa0
[  308.020605]  ? rcu_read_lock_sched_held+0xc0/0xc0
[  308.021286]  ? bond_get_stats+0x9f/0x500 [bonding]
[  308.021953]  dev_get_stats+0x1ec/0x270
[  308.022508]  bond_get_stats+0x1d1/0x500 [bonding]

Fixes: d3fff6c443fe ("net: add netdev_lockdep_set_classes() helper")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: fix unexpected IFF_BONDING bit unset

The IFF_BONDING means bonding master or bonding slave device.
->ndo_add_slave() sets IFF_BONDING flag and ->ndo_del_slave() unsets
IFF_BONDING flag.

bond0<--bond1

Both bond0 and bond1 are bonding device and these should keep having
IFF_BONDING flag until they are removed.
But bond1 would lose IFF_BONDING at ->ndo_del_slave() because that routine
do not check whether the slave device is the bonding type or not.
This patch adds the interface type check routine before removing
IFF_BONDING flag.

Test commands:
    ip link add bond0 type bond
    ip link add bond1 type bond
    ip link set bond1 master bond0
    ip link set bond1 nomaster
    ip link del bond1 type bond
    ip link add bond1 type bond

Splat looks like:
[  226.665555] proc_dir_entry 'bonding/bond1' already registered
[  226.666440] WARNING: CPU: 0 PID: 737 at fs/proc/generic.c:361 proc_register+0x2a9/0x3e0
[  226.667571] Modules linked in: bonding af_packet sch_fq_codel ip_tables x_tables unix
[  226.668662] CPU: 0 PID: 737 Comm: ip Not tainted 5.4.0-rc3+ #96
[  226.669508] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[  226.670652] RIP: 0010:proc_register+0x2a9/0x3e0
[  226.671612] Code: 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 39 01 00 00 48 8b 04 24 48 89 ea 48 c7 c7 a0 0b 14 9f 48 8b b0 e
0 00 00 00 e8 07 e7 88 ff <0f> 0b 48 c7 c7 40 2d a5 9f e8 59 d6 23 01 48 8b 4c 24 10 48 b8 00
[  226.675007] RSP: 0018:ffff888050e17078 EFLAGS: 00010282
[  226.675761] RAX: dffffc0000000008 RBX: ffff88805fdd0f10 RCX: ffffffff9dd344e2
[  226.676757] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffff88806c9f6b8c
[  226.677751] RBP: ffff8880507160f3 R08: ffffed100d940019 R09: ffffed100d940019
[  226.678761] R10: 0000000000000001 R11: ffffed100d940018 R12: ffff888050716008
[  226.679757] R13: ffff8880507160f2 R14: dffffc0000000000 R15: ffffed100a0e2c1e
[  226.680758] FS:  00007fdc217cc0c0(0000) GS:ffff88806c800000(0000) knlGS:0000000000000000
[  226.681886] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  226.682719] CR2: 00007f49313424d0 CR3: 0000000050e46001 CR4: 00000000000606f0
[  226.683727] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  226.684725] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  226.685681] Call Trace:
[  226.687089]  proc_create_seq_private+0xb3/0xf0
[  226.687778]  bond_create_proc_entry+0x1b3/0x3f0 [bonding]
[  226.691458]  bond_netdev_event+0x433/0x970 [bonding]
[  226.692139]  ? __module_text_address+0x13/0x140
[  226.692779]  notifier_call_chain+0x90/0x160
[  226.693401]  register_netdevice+0x9b3/0xd80
[  226.694010]  ? alloc_netdev_mqs+0x854/0xc10
[  226.694629]  ? netdev_change_features+0xa0/0xa0
[  226.695278]  ? rtnl_create_link+0x2ed/0xad0
[  226.695849]  bond_newlink+0x2a/0x60 [bonding]
[  226.696422]  __rtnl_newlink+0xb9f/0x11b0
[  226.696968]  ? rtnl_link_unregister+0x220/0x220
[ ... ]

Fixes: 0b680e753724 ("[PATCH] bonding: Add priv_flag to avoid event mishandling")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: core: add generic lockdep keys

Some interface types could be nested.
(VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, VIRT_WIFI, VXLAN, etc..)
These interface types should set lockdep class because, without lockdep
class key, lockdep always warn about unexisting circular locking.

In the current code, these interfaces have their own lockdep class keys and
these manage itself. So that there are so many duplicate code around the
/driver/net and /net/.
This patch adds new generic lockdep keys and some helper functions for it.

This patch does below changes.
a) Add lockdep class keys in struct net_device
   - qdisc_running, xmit, addr_list, qdisc_busylock
   - these keys are used as dynamic lockdep key.
b) When net_device is being allocated, lockdep keys are registered.
   - alloc_netdev_mqs()
c) When net_device is being free'd llockdep keys are unregistered.
   - free_netdev()
d) Add generic lockdep key helper function
   - netdev_register_lockdep_key()
   - netdev_unregister_lockdep_key()
   - netdev_update_lockdep_key()
e) Remove unnecessary generic lockdep macro and functions
f) Remove unnecessary lockdep code of each interfaces.

After this patch, each interface modules don't need to maintain
their lockdep keys.

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: core: limit nested device depth

Current code doesn't limit the number of nested devices.
Nested devices would be handled recursively and this needs huge stack
memory. So, unlimited nested devices could make stack overflow.

This patch adds upper_level and lower_level, they are common variables
and represent maximum lower/upper depth.
When upper/lower device is attached or dettached,
{lower/upper}_level are updated. and if maximum depth is bigger than 8,
attach routine fails and returns -EMLINK.

In addition, this patch converts recursive routine of
netdev_walk_all_{lower/upper} to iterator routine.

Test commands:
    ip link add dummy0 type dummy
    ip link add link dummy0 name vlan1 type vlan id 1
    ip link set vlan1 up

    for i in {2..55}
    do
    let A=$i-1

    ip link add vlan$i link vlan$A type vlan id $i
    done
    ip link del dummy0

Splat looks like:
[  155.513226][  T908] BUG: KASAN: use-after-free in __unwind_start+0x71/0x850
[  155.514162][  T908] Write of size 88 at addr ffff8880608a6cc0 by task ip/908
[  155.515048][  T908]
[  155.515333][  T908] CPU: 0 PID: 908 Comm: ip Not tainted 5.4.0-rc3+ #96
[  155.516147][  T908] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[  155.517233][  T908] Call Trace:
[  155.517627][  T908]
[  155.517918][  T908] Allocated by task 0:
[  155.518412][  T908] (stack is not available)
[  155.518955][  T908]
[  155.519228][  T908] Freed by task 0:
[  155.519885][  T908] (stack is not available)
[  155.520452][  T908]
[  155.520729][  T908] The buggy address belongs to the object at ffff8880608a6ac0
[  155.520729][  T908]  which belongs to the cache names_cache of size 4096
[  155.522387][  T908] The buggy address is located 512 bytes inside of
[  155.522387][  T908]  4096-byte region [ffff8880608a6ac0, ffff8880608a7ac0)
[  155.523920][  T908] The buggy address belongs to the page:
[  155.524552][  T908] page:ffffea0001822800 refcount:1 mapcount:0 mapping:ffff88806c657cc0 index:0x0 compound_mapcount:0
[  155.525836][  T908] flags: 0x100000000010200(slab|head)
[  155.526445][  T908] raw: 0100000000010200 ffffea0001813808 ffffea0001a26c08 ffff88806c657cc0
[  155.527424][  T908] raw: 0000000000000000 0000000000070007 00000001ffffffff 0000000000000000
[  155.528429][  T908] page dumped because: kasan: bad access detected
[  155.529158][  T908]
[  155.529410][  T908] Memory state around the buggy address:
[  155.530060][  T908]  ffff8880608a6b80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  155.530971][  T908]  ffff8880608a6c00: fb fb fb fb fb f1 f1 f1 f1 00 f2 f2 f2 f3 f3 f3
[  155.531889][  T908] >ffff8880608a6c80: f3 fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  155.532806][  T908]                                            ^
[  155.533509][  T908]  ffff8880608a6d00: fb fb fb fb fb fb fb fb fb f1 f1 f1 f1 00 00 00
[  155.534436][  T908]  ffff8880608a6d80: f2 f3 f3 f3 f3 fb fb fb 00 00 00 00 00 00 00 00
[ ... ]

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

keys: Fix memory leak in copy_net_ns

If copy_net_ns() failed after net_alloc(), net->key_domain is leaked.
Fix this, by freeing key_domain in error path.

syzbot report:
BUG: memory leak
unreferenced object 0xffff8881175007e0 (size 32):
  comm "syz-executor902", pid 7069, jiffies 4294944350 (age 28.400s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<00000000a83ed741>] kmemleak_alloc_recursive include/linux/kmemleak.h:43 [inline]
    [<00000000a83ed741>] slab_post_alloc_hook mm/slab.h:439 [inline]
    [<00000000a83ed741>] slab_alloc mm/slab.c:3326 [inline]
    [<00000000a83ed741>] kmem_cache_alloc_trace+0x13d/0x280 mm/slab.c:3553
    [<0000000059fc92b9>] kmalloc include/linux/slab.h:547 [inline]
    [<0000000059fc92b9>] kzalloc include/linux/slab.h:742 [inline]
    [<0000000059fc92b9>] net_alloc net/core/net_namespace.c:398 [inline]
    [<0000000059fc92b9>] copy_net_ns+0xb2/0x220 net/core/net_namespace.c:445
    [<00000000a9d74bbc>] create_new_namespaces+0x141/0x2a0 kernel/nsproxy.c:103
    [<000000008047d645>] unshare_nsproxy_namespaces+0x7f/0x100 kernel/nsproxy.c:202
    [<000000005993ea6e>] ksys_unshare+0x236/0x490 kernel/fork.c:2674
    [<0000000019417e75>] __do_sys_unshare kernel/fork.c:2742 [inline]
    [<0000000019417e75>] __se_sys_unshare kernel/fork.c:2740 [inline]
    [<0000000019417e75>] __x64_sys_unshare+0x16/0x20 kernel/fork.c:2740
    [<00000000f4c5f2c8>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:296
    [<0000000038550184>] entry_SYSCALL_64_after_hwframe+0x44/0xa9

syzbot also reported other leak in copy_net_ns -> setup_net.
This problem is already fixed by cf47a0b882a4e5f6b34c7949d7b293e9287f1972.

Fixes: 9b242610514f ("keys: Network namespace domain tag")
Reported-and-tested-by: syzbot+3b3296d032353c33184b@syzkaller.appspotmail.com
Signed-off-by: Takeshi Misawa <jeliantsurux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netfilter: nft_payload: fix missing check for matching length in offloads

Payload offload rule should also check the length of the match.
Moreover, check for unsupported link-layer fields:

nft --debug=netlink add rule firewall zones vlan id 100
...
[ payload load 2b @ link header + 0 => reg 1 ]

this loads 2byte base on ll header and offset 0.

This also fixes unsupported raw payload match.

Fixes: 92ad6325cb89 ("netfilter: nf_tables: add hardware offload support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

ipvs: move old_secure_tcp into struct netns_ipvs

syzbot reported the following issue :

BUG: KCSAN: data-race in update_defense_level / update_defense_level

read to 0xffffffff861a6260 of 4 bytes by task 3006 on cpu 1:
update_defense_level+0x621/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:177
defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352

write to 0xffffffff861a6260 of 4 bytes by task 7333 on cpu 0:
update_defense_level+0xa62/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:205
defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7333 Comm: kworker/0:5 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events defense_work_handler

Indeed, old_secure_tcp is currently a static variable, while it
needs to be a per netns variable.

Fixes: a0840e2e165a ("IPVS: netns, ip_vs_ctl local vars moved to ipvs struct.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Simon Horman <horms@verge.net.au>

ipvs: don't ignore errors in case refcounting ip_vs module fails

if the IPVS module is removed while the sync daemon is starting, there is
a small gap where try_module_get() might fail getting the refcount inside
ip_vs_use_count_inc(). Then, the refcounts of IPVS module are unbalanced,
and the subsequent call to stop_sync_thread() causes the following splat:

WARNING: CPU: 0 PID: 4013 at kernel/module.c:1146 module_put.part.44+0x15b/0x290
  Modules linked in: ip_vs(-) nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 veth ip6table_filter ip6_tables iptable_filter binfmt_misc intel_rapl_msr intel_rapl_common crct10dif_pclmul crc32_pclmul ext4 mbcache jbd2 ghash_clmulni_intel snd_hda_codec_generic ledtrig_audio snd_hda_intel snd_intel_nhlt snd_hda_codec snd_hda_core snd_hwdep snd_seq snd_seq_device snd_pcm aesni_intel crypto_simd cryptd glue_helper joydev pcspkr snd_timer virtio_balloon snd soundcore i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi virtio_net net_failover virtio_blk failover virtio_console qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ata_piix ttm crc32c_intel serio_raw drm virtio_pci libata virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: nf_defrag_ipv6]
  CPU: 0 PID: 4013 Comm: modprobe Tainted: G        W         5.4.0-rc1.upstream+ #741
  Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
  RIP: 0010:module_put.part.44+0x15b/0x290
  Code: 04 25 28 00 00 00 0f 85 18 01 00 00 48 83 c4 68 5b 5d 41 5c 41 5d 41 5e 41 5f c3 89 44 24 28 83 e8 01 89 c5 0f 89 57 ff ff ff <0f> 0b e9 78 ff ff ff 65 8b 1d 67 83 26 4a 89 db be 08 00 00 00 48
  RSP: 0018:ffff888050607c78 EFLAGS: 00010297
  RAX: 0000000000000003 RBX: ffffffffc1420590 RCX: ffffffffb5db0ef9
  RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffffc1420590
  RBP: 00000000ffffffff R08: fffffbfff82840b3 R09: fffffbfff82840b3
  R10: 0000000000000001 R11: fffffbfff82840b2 R12: 1ffff1100a0c0f90
  R13: ffffffffc1420200 R14: ffff88804f533300 R15: ffff88804f533ca0
  FS:  00007f8ea9720740(0000) GS:ffff888053800000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00007f3245abe000 CR3: 000000004c28a006 CR4: 00000000001606f0
  Call Trace:
   stop_sync_thread+0x3a3/0x7c0 [ip_vs]
   ip_vs_sync_net_cleanup+0x13/0x50 [ip_vs]
   ops_exit_list.isra.5+0x94/0x140
   unregister_pernet_operations+0x29d/0x460
   unregister_pernet_device+0x26/0x60
   ip_vs_cleanup+0x11/0x38 [ip_vs]
   __x64_sys_delete_module+0x2d5/0x400
   do_syscall_64+0xa5/0x4e0
   entry_SYSCALL_64_after_hwframe+0x49/0xbe
  RIP: 0033:0x7f8ea8bf0db7
  Code: 73 01 c3 48 8b 0d b9 80 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 89 80 2c 00 f7 d8 64 89 01 48
  RSP: 002b:00007ffcd38d2fe8 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
  RAX: ffffffffffffffda RBX: 0000000002436240 RCX: 00007f8ea8bf0db7
  RDX: 0000000000000000 RSI: 0000000000000800 RDI: 00000000024362a8
  RBP: 0000000000000000 R08: 00007f8ea8eba060 R09: 00007f8ea8c658a0
  R10: 00007ffcd38d2a60 R11: 0000000000000206 R12: 0000000000000000
  R13: 0000000000000001 R14: 00000000024362a8 R15: 0000000000000000
  irq event stamp: 4538
  hardirqs last  enabled at (4537): [<ffffffffb6193dde>] quarantine_put+0x9e/0x170
  hardirqs last disabled at (4538): [<ffffffffb5a0556a>] trace_hardirqs_off_thunk+0x1a/0x20
  softirqs last  enabled at (4522): [<ffffffffb6f8ebe9>] sk_common_release+0x169/0x2d0
  softirqs last disabled at (4520): [<ffffffffb6f8eb3e>] sk_common_release+0xbe/0x2d0

Check the return value of ip_vs_use_count_inc() and let its caller return
proper error. Inside do_ip_vs_set_ctl() the module is already refcounted,
we don't need refcount/derefcount there. Finally, in register_ip_vs_app()
and start_sync_thread(), take the module refcount earlier and ensure it's
released in the error path.

Change since v1:
- better return values in case of failure of ip_vs_use_count_inc(),
   thanks to Julian Anastasov
- no need to increase/decrease the module refcount in ip_vs_set_ctl(),
   thanks to Julian Anastasov

Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>

net: phy: smsc: LAN8740: add PHY_RST_AFTER_CLK_EN flag

The LAN8740, like the 8720, also requires a reset after enabling clock.
The datasheet [1] 3.8.5.1 says:
"During a Hardware reset, an external clock must be supplied
to the XTAL1/CLKIN signal."

I have observed this issue on a custom i.MX6 based board with
the LAN8740A.

[1] http://ww1.microchip.com/downloads/en/DeviceDoc/8740a.pdf

Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

xsk: Fix registration of Rx-only sockets

Having Rx-only AF_XDP sockets can potentially lead to a crash in the
system by a NULL pointer dereference in xsk_umem_consume_tx(). This
function iterates through a list of all sockets tied to a umem and
checks if there are any packets to send on the Tx ring. Rx-only
sockets do not have a Tx ring, so this will cause a NULL pointer
dereference. This will happen if you have registered one or more
Rx-only sockets to a umem and the driver is checking the Tx ring even
on Rx, or if the XDP_SHARED_UMEM mode is used and there is a mix of
Rx-only and other sockets tied to the same umem.

Fixed by only putting sockets with a Tx component on the list that
xsk_umem_consume_tx() iterates over.

Fixes: ac98d8aab61b ("xsk: wire upp Tx zero-copy functions")
Reported-by: Kal Cutter Conley <kal.conley@dectris.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/bpf/1571645818-16244-1-git-send-email-magnus.karlsson@intel.com

net/flow_dissector: switch to siphash

UDP IPv6 packets auto flowlabels are using a 32bit secret
(static u32 hashrnd in net/core/flow_dissector.c) and
apply jhash() over fields known by the receivers.

Attackers can easily infer the 32bit secret and use this information
to identify a device and/or user, since this 32bit secret is only
set at boot time.

Really, using jhash() to generate cookies sent on the wire
is a serious security concern.

Trying to change the rol32(hash, 16) in ip6_make_flowlabel() would be
a dead end. Trying to periodically change the secret (like in sch_sfq.c)
could change paths taken in the network for long lived flows.

Let's switch to siphash, as we did in commit df453700e8d8
("inet: switch IP ID generator to siphash")

Using a cryptographically strong pseudo random function will solve this
privacy issue and more generally remove other weak points in the stack.

Packet schedulers using skb_get_hash_perturb() benefit from this change.

Fixes: b56774163f99 ("ipv6: Enable auto flow labels by default")
Fixes: 42240901f7c4 ("ipv6: Implement different admin modes for automatic flow labels")
Fixes: 67800f9b1f4e ("ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabel")
Fixes: cb1ce2ef387b ("ipv6: Implement automatic flow label generation on transmit")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Berger <jonathann1@walla.com>
Reported-by: Amit Klein <aksecurity@gmail.com>
Reported-by: Benny Pinkas <benny@pinkas.net>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netfilter: nf_tables_offload: restore basechain deletion

Unbind callbacks on chain deletion.

Fixes: 8fc618c52d16 ("netfilter: nf_tables_offload: refactor the nft_flow_offload_chain function")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

netfilter: nf_flow_table: set timeout before insertion into hashes

Other garbage collector might remove an entry not fully set up yet.

[570953.958293] RIP: 0010:memcmp+0x9/0x50
[...]
[570953.958567]  flow_offload_hash_cmp+0x1e/0x30 [nf_flow_table]
[570953.958585]  flow_offload_lookup+0x8c/0x110 [nf_flow_table]
[570953.958606]  nf_flow_offload_ip_hook+0x135/0xb30 [nf_flow_table]
[570953.958624]  nf_flow_offload_inet_hook+0x35/0x37 [nf_flow_table_inet]
[570953.958646]  nf_hook_slow+0x3c/0xb0
[570953.958664]  __netif_receive_skb_core+0x90f/0xb10
[570953.958678]  ? ip_rcv_finish+0x82/0xa0
[570953.958692]  __netif_receive_skb_one_core+0x3b/0x80
[570953.958711]  __netif_receive_skb+0x18/0x60
[570953.958727]  netif_receive_skb_internal+0x45/0xf0
[570953.958741]  napi_gro_receive+0xcd/0xf0
[570953.958764]  ixgbe_clean_rx_irq+0x432/0xe00 [ixgbe]
[570953.958782]  ixgbe_poll+0x27b/0x700 [ixgbe]
[570953.958796]  net_rx_action+0x284/0x3c0
[570953.958817]  __do_softirq+0xcc/0x27c
[570953.959464]  irq_exit+0xe8/0x100
[570953.960097]  do_IRQ+0x59/0xe0
[570953.960734]  common_interrupt+0xf/0xf

Fixes: 43c8f131184f ("netfilter: nf_flow_table: fix missing error check for rhashtable_insert_fast")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

bpf: Fix use after free in bpf_get_prog_name

There is one more problematic case I noticed while recently fixing BPF kallsyms
handling in cd7455f1013e ("bpf: Fix use after free in subprog's jited symbol
removal") and that is bpf_get_prog_name().

If BTF has been attached to the prog, then we may be able to fetch the function
signature type id in kallsyms through prog->aux->func_info[prog->aux->func_idx].type_id.
However, while the BTF object itself is torn down via RCU callback, the prog's
aux->func_info is immediately freed via kvfree(prog->aux->func_info) once the
prog's refcount either hit zero or when subprograms were already exposed via
kallsyms and we hit the error path added in 5482e9a93c83 ("bpf: Fix memleak in
aux->func_info and aux->btf").

This violates RCU as well since kallsyms could be walked in parallel where we
could access aux->func_info. Hence, defer kvfree() to after RCU grace period.
Looking at ba64e7d85252 ("bpf: btf: support proper non-jit func info") there
is no reason/dependency where we couldn't defer the kvfree(aux->func_info) into
the RCU callback.

Fixes: 5482e9a93c83 ("bpf: Fix memleak in aux->func_info and aux->btf")
Fixes: ba64e7d85252 ("bpf: btf: support proper non-jit func info")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/875f2906a7c1a0691f2d567b4d8e4ea2739b1e88.1571779205.git.daniel@iogearbox.net

ipv6: include <net/addrconf.h> for missing declarations

Include <net/addrconf.h> for the missing declarations of
various functions. Fixes the following sparse warnings:

net/ipv6/addrconf_core.c:94:5: warning: symbol 'register_inet6addr_notifier' was not declared. Should it be static?
net/ipv6/addrconf_core.c:100:5: warning: symbol 'unregister_inet6addr_notifier' was not declared. Should it be static?
net/ipv6/addrconf_core.c:106:5: warning: symbol 'inet6addr_notifier_call_chain' was not declared. Should it be static?
net/ipv6/addrconf_core.c:112:5: warning: symbol 'register_inet6addr_validator_notifier' was not declared. Should it be static?
net/ipv6/addrconf_core.c:118:5: warning: symbol 'unregister_inet6addr_validator_notifier' was not declared. Should it be static?
net/ipv6/addrconf_core.c:125:5: warning: symbol 'inet6addr_validator_notifier_call_chain' was not declared. Should it be static?
net/ipv6/addrconf_core.c:237:6: warning: symbol 'in6_dev_finish_destroy' was not declared. Should it be static?

Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: openvswitch: free vport unless register_netdevice() succeeds

syzbot found the following crash on:

HEAD commit:    1e78030e Merge tag 'mmc-v5.3-rc1' of git://git.kernel.org/..
git tree:       upstream
console output: https://syzkaller.appspot.com/x/log.txt?x=148d3d1a600000
kernel config:  https://syzkaller.appspot.com/x/.config?x=30cef20daf3e9977
link: https://syzkaller.appspot.com/bug?extid=13210896153522fe1ee5
compiler:       gcc (GCC) 9.0.0 20181231 (experimental)
syz repro:      https://syzkaller.appspot.com/x/repro.syz?x=136aa8c4600000
C reproducer:   https://syzkaller.appspot.com/x/repro.c?x=109ba792600000

=====================================================================
BUG: memory leak
unreferenced object 0xffff8881207e4100 (size 128):
   comm "syz-executor032", pid 7014, jiffies 4294944027 (age 13.830s)
   hex dump (first 32 bytes):
     00 70 16 18 81 88 ff ff 80 af 8c 22 81 88 ff ff  .p........."....
     00 b6 23 17 81 88 ff ff 00 00 00 00 00 00 00 00  ..#.............
   backtrace:
     [<000000000eb78212>] kmemleak_alloc_recursive  include/linux/kmemleak.h:43 [inline]
     [<000000000eb78212>] slab_post_alloc_hook mm/slab.h:522 [inline]
     [<000000000eb78212>] slab_alloc mm/slab.c:3319 [inline]
     [<000000000eb78212>] kmem_cache_alloc_trace+0x145/0x2c0 mm/slab.c:3548
     [<00000000006ea6c6>] kmalloc include/linux/slab.h:552 [inline]
     [<00000000006ea6c6>] kzalloc include/linux/slab.h:748 [inline]
     [<00000000006ea6c6>] ovs_vport_alloc+0x37/0xf0  net/openvswitch/vport.c:130
     [<00000000f9a04a7d>] internal_dev_create+0x24/0x1d0  net/openvswitch/vport-internal_dev.c:164
     [<0000000056ee7c13>] ovs_vport_add+0x81/0x190  net/openvswitch/vport.c:199
     [<000000005434efc7>] new_vport+0x19/0x80 net/openvswitch/datapath.c:194
     [<00000000b7b253f1>] ovs_dp_cmd_new+0x22f/0x410  net/openvswitch/datapath.c:1614
     [<00000000e0988518>] genl_family_rcv_msg+0x2ab/0x5b0  net/netlink/genetlink.c:629
     [<00000000d0cc9347>] genl_rcv_msg+0x54/0x9c net/netlink/genetlink.c:654
     [<000000006694b647>] netlink_rcv_skb+0x61/0x170  net/netlink/af_netlink.c:2477
     [<0000000088381f37>] genl_rcv+0x29/0x40 net/netlink/genetlink.c:665
     [<00000000dad42a47>] netlink_unicast_kernel  net/netlink/af_netlink.c:1302 [inline]
     [<00000000dad42a47>] netlink_unicast+0x1ec/0x2d0  net/netlink/af_netlink.c:1328
     [<0000000067e6b079>] netlink_sendmsg+0x270/0x480  net/netlink/af_netlink.c:1917
     [<00000000aab08a47>] sock_sendmsg_nosec net/socket.c:637 [inline]
     [<00000000aab08a47>] sock_sendmsg+0x54/0x70 net/socket.c:657
     [<000000004cb7c11d>] ___sys_sendmsg+0x393/0x3c0 net/socket.c:2311
     [<00000000c4901c63>] __sys_sendmsg+0x80/0xf0 net/socket.c:2356
     [<00000000c10abb2d>] __do_sys_sendmsg net/socket.c:2365 [inline]
     [<00000000c10abb2d>] __se_sys_sendmsg net/socket.c:2363 [inline]
     [<00000000c10abb2d>] __x64_sys_sendmsg+0x23/0x30 net/socket.c:2363

BUG: memory leak
unreferenced object 0xffff88811723b600 (size 64):
   comm "syz-executor032", pid 7014, jiffies 4294944027 (age 13.830s)
   hex dump (first 32 bytes):
     01 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00  ................
     00 00 00 00 00 00 00 00 02 00 00 00 05 35 82 c1  .............5..
   backtrace:
     [<00000000352f46d8>] kmemleak_alloc_recursive  include/linux/kmemleak.h:43 [inline]
     [<00000000352f46d8>] slab_post_alloc_hook mm/slab.h:522 [inline]
     [<00000000352f46d8>] slab_alloc mm/slab.c:3319 [inline]
     [<00000000352f46d8>] __do_kmalloc mm/slab.c:3653 [inline]
     [<00000000352f46d8>] __kmalloc+0x169/0x300 mm/slab.c:3664
     [<000000008e48f3d1>] kmalloc include/linux/slab.h:557 [inline]
     [<000000008e48f3d1>] ovs_vport_set_upcall_portids+0x54/0xd0  net/openvswitch/vport.c:343
     [<00000000541e4f4a>] ovs_vport_alloc+0x7f/0xf0  net/openvswitch/vport.c:139
     [<00000000f9a04a7d>] internal_dev_create+0x24/0x1d0  net/openvswitch/vport-internal_dev.c:164
     [<0000000056ee7c13>] ovs_vport_add+0x81/0x190  net/openvswitch/vport.c:199
     [<000000005434efc7>] new_vport+0x19/0x80 net/openvswitch/datapath.c:194
     [<00000000b7b253f1>] ovs_dp_cmd_new+0x22f/0x410  net/openvswitch/datapath.c:1614
     [<00000000e0988518>] genl_family_rcv_msg+0x2ab/0x5b0  net/netlink/genetlink.c:629
     [<00000000d0cc9347>] genl_rcv_msg+0x54/0x9c net/netlink/genetlink.c:654
     [<000000006694b647>] netlink_rcv_skb+0x61/0x170  net/netlink/af_netlink.c:2477
     [<0000000088381f37>] genl_rcv+0x29/0x40 net/netlink/genetlink.c:665
     [<00000000dad42a47>] netlink_unicast_kernel  net/netlink/af_netlink.c:1302 [inline]
     [<00000000dad42a47>] netlink_unicast+0x1ec/0x2d0  net/netlink/af_netlink.c:1328
     [<0000000067e6b079>] netlink_sendmsg+0x270/0x480  net/netlink/af_netlink.c:1917
     [<00000000aab08a47>] sock_sendmsg_nosec net/socket.c:637 [inline]
     [<00000000aab08a47>] sock_sendmsg+0x54/0x70 net/socket.c:657
     [<000000004cb7c11d>] ___sys_sendmsg+0x393/0x3c0 net/socket.c:2311
     [<00000000c4901c63>] __sys_sendmsg+0x80/0xf0 net/socket.c:2356

BUG: memory leak
unreferenced object 0xffff8881228ca500 (size 128):
   comm "syz-executor032", pid 7015, jiffies 4294944622 (age 7.880s)
   hex dump (first 32 bytes):
     00 f0 27 18 81 88 ff ff 80 ac 8c 22 81 88 ff ff  ..'........"....
     40 b7 23 17 81 88 ff ff 00 00 00 00 00 00 00 00  @.#.............
   backtrace:
     [<000000000eb78212>] kmemleak_alloc_recursive  include/linux/kmemleak.h:43 [inline]
     [<000000000eb78212>] slab_post_alloc_hook mm/slab.h:522 [inline]
     [<000000000eb78212>] slab_alloc mm/slab.c:3319 [inline]
     [<000000000eb78212>] kmem_cache_alloc_trace+0x145/0x2c0 mm/slab.c:3548
     [<00000000006ea6c6>] kmalloc include/linux/slab.h:552 [inline]
     [<00000000006ea6c6>] kzalloc include/linux/slab.h:748 [inline]
     [<00000000006ea6c6>] ovs_vport_alloc+0x37/0xf0  net/openvswitch/vport.c:130
     [<00000000f9a04a7d>] internal_dev_create+0x24/0x1d0  net/openvswitch/vport-internal_dev.c:164
     [<0000000056ee7c13>] ovs_vport_add+0x81/0x190  net/openvswitch/vport.c:199
     [<000000005434efc7>] new_vport+0x19/0x80 net/openvswitch/datapath.c:194
     [<00000000b7b253f1>] ovs_dp_cmd_new+0x22f/0x410  net/openvswitch/datapath.c:1614
     [<00000000e0988518>] genl_family_rcv_msg+0x2ab/0x5b0  net/netlink/genetlink.c:629
     [<00000000d0cc9347>] genl_rcv_msg+0x54/0x9c net/netlink/genetlink.c:654
     [<000000006694b647>] netlink_rcv_skb+0x61/0x170  net/netlink/af_netlink.c:2477
     [<0000000088381f37>] genl_rcv+0x29/0x40 net/netlink/genetlink.c:665
     [<00000000dad42a47>] netlink_unicast_kernel  net/netlink/af_netlink.c:1302 [inline]
     [<00000000dad42a47>] netlink_unicast+0x1ec/0x2d0  net/netlink/af_netlink.c:1328
     [<0000000067e6b079>] netlink_sendmsg+0x270/0x480  net/netlink/af_netlink.c:1917
     [<00000000aab08a47>] sock_sendmsg_nosec net/socket.c:637 [inline]
     [<00000000aab08a47>] sock_sendmsg+0x54/0x70 net/socket.c:657
     [<000000004cb7c11d>] ___sys_sendmsg+0x393/0x3c0 net/socket.c:2311
     [<00000000c4901c63>] __sys_sendmsg+0x80/0xf0 net/socket.c:2356
     [<00000000c10abb2d>] __do_sys_sendmsg net/socket.c:2365 [inline]
     [<00000000c10abb2d>] __se_sys_sendmsg net/socket.c:2363 [inline]
     [<00000000c10abb2d>] __x64_sys_sendmsg+0x23/0x30 net/socket.c:2363
=====================================================================

The function in net core, register_netdevice(), may fail with vport's
destruction callback either invoked or not. After commit 309b66970ee2
("net: openvswitch: do not free vport if register_netdevice() is failed."),
the duty to destroy vport is offloaded from the driver OTOH, which ends
up in the memory leak reported.

It is fixed by releasing vport unless device is registered successfully.
To do that, the callback assignment is defered until device is registered.

Reported-by: syzbot+13210896153522fe1ee5@syzkaller.appspotmail.com
Fixes: 309b66970ee2 ("net: openvswitch: do not free vport if register_netdevice() is failed.")
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Greg Rose <gvrose8192@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Hillf Danton <hdanton@sina.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
[sbrivio: this was sent to dev@openvswitch.org and never made its way
to netdev -- resending original patch]
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

selftests: Make l2tp.sh executable

Kernel test robot reported that the l2tp.sh test script failed:
# selftests: net: l2tp.sh
# Warning: file l2tp.sh is not executable, correct this.

Set executable bits.

Fixes: e858ef1cd4bc ("selftests: Add l2tp tests")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: sched: taprio: fix -Wmissing-prototypes warnings

We get one warnings when build kernel W=1:
net/sched/sch_taprio.c:1155:6: warning: no previous prototype for ‘taprio_offload_config_changed’ [-Wmissing-prototypes]

Make the function static to fix this.

Fixes: 9c66d1564676 ("taprio: Add support for hardware offloading")
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

Merge branch 'bnxt_en-bug-fixes'

Michael Chan says:

====================
Devlink and error recovery bug fix patches.
Most of the work is by Vasundhara Volam.
====================

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

bnxt_en: Avoid disabling pci device in bnxt_remove_one() for already disabled device.

With the recently added error recovery logic, the device may already
be disabled if the firmware recovery is unsuccessful. In
bnxt_remove_one(), check that the device is still enabled first
before calling pci_disable_device().

Fixes: 3bc7d4a352ef ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

bnxt_en: Minor formatting changes in FW devlink_health_reporter

Minor formatting changes to diagnose cb for FW devlink health
reporter.

Suggested-by: Jiri Pirko <jiri@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

bnxt_en: Adjust the time to wait before polling firmware readiness.

When firmware indicates that driver needs to invoke firmware reset
which is common for both error recovery and live firmware reset path,
driver needs a different time to wait before polling for firmware
readiness.

Modify the wait time to fw_reset_min_dsecs, which is initialised to
correct timeout for error recovery and firmware reset.

Fixes: 4037eb715680 ("bnxt_en: Add a new BNXT_FW_RESET_STATE_POLL_FW_DOWN state.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

bnxt_en: Fix devlink NVRAM related byte order related issues.

The current code does not do endian swapping between the devlink
parameter and the internal NVRAM representation. Define a union to
represent the little endian NVRAM data and add 2 helper functions to
copy to and from the NVRAM data with the proper byte swapping.

Fixes: 782a624d00fa ("bnxt_en: Add bnxt_en initial port params table and register it")
Cc: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

bnxt_en: Fix the size of devlink MSIX parameters.

The current code that rounds up the NVRAM parameter bit size to the next
byte size for the devlink parameter is not always correct. The MSIX
devlink parameters are 4 bytes and we don't get the correct size
using this method.

Fix it by adding a new dl_num_bytes member to the bnxt_dl_nvm_param
structure which statically provides bytesize information according
to the devlink parameter type definition.

Fixes: 782a624d00fa ("bnxt_en: Add bnxt_en initial port params table and register it")
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: stmmac: Fix the problem of tso_xmit

When the address width of DMA is greater than 32, the packet header occupies
a BD descriptor. The starting address of the data should be added to the
header length.

Fixes: a993db88d17d ("net: stmmac: Enable support for > 32 Bits addressing in XGMAC")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: yuqi jin <jinyuqi@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

dynamic_debug: provide dynamic_hex_dump stub

The ionic driver started using dymamic_hex_dump(), but
that is not always defined:

drivers/net/ethernet/pensando/ionic/ionic_main.c:229:2: error: implicit declaration of function 'dynamic_hex_dump' [-Werror,-Wimplicit-function-declaration]

Add a dummy implementation to use when CONFIG_DYNAMIC_DEBUG
is disabled, printing nothing.

Fixes: 938962d55229 ("ionic: Add adminq action")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

bpf: Fix use after free in subprog's jited symbol removal

syzkaller managed to trigger the following crash:

  [...]
  BUG: unable to handle page fault for address: ffffc90001923030
  #PF: supervisor read access in kernel mode
  #PF: error_code(0x0000) - not-present page
  PGD aa551067 P4D aa551067 PUD aa552067 PMD a572b067 PTE 80000000a1173163
  Oops: 0000 [#1] PREEMPT SMP KASAN
  CPU: 0 PID: 7982 Comm: syz-executor912 Not tainted 5.4.0-rc3+ #0
  Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
  RIP: 0010:bpf_jit_binary_hdr include/linux/filter.h:787 [inline]
  RIP: 0010:bpf_get_prog_addr_region kernel/bpf/core.c:531 [inline]
  RIP: 0010:bpf_tree_comp kernel/bpf/core.c:600 [inline]
  RIP: 0010:__lt_find include/linux/rbtree_latch.h:115 [inline]
  RIP: 0010:latch_tree_find include/linux/rbtree_latch.h:208 [inline]
  RIP: 0010:bpf_prog_kallsyms_find kernel/bpf/core.c:674 [inline]
  RIP: 0010:is_bpf_text_address+0x184/0x3b0 kernel/bpf/core.c:709
  [...]
  Call Trace:
   kernel_text_address kernel/extable.c:147 [inline]
   __kernel_text_address+0x9a/0x110 kernel/extable.c:102
   unwind_get_return_address+0x4c/0x90 arch/x86/kernel/unwind_frame.c:19
   arch_stack_walk+0x98/0xe0 arch/x86/kernel/stacktrace.c:26
   stack_trace_save+0xb6/0x150 kernel/stacktrace.c:123
   save_stack mm/kasan/common.c:69 [inline]
   set_track mm/kasan/common.c:77 [inline]
   __kasan_kmalloc+0x11c/0x1b0 mm/kasan/common.c:510
   kasan_slab_alloc+0xf/0x20 mm/kasan/common.c:518
   slab_post_alloc_hook mm/slab.h:584 [inline]
   slab_alloc mm/slab.c:3319 [inline]
   kmem_cache_alloc+0x1f5/0x2e0 mm/slab.c:3483
   getname_flags+0xba/0x640 fs/namei.c:138
   getname+0x19/0x20 fs/namei.c:209
   do_sys_open+0x261/0x560 fs/open.c:1091
   __do_sys_open fs/open.c:1115 [inline]
   __se_sys_open fs/open.c:1110 [inline]
   __x64_sys_open+0x87/0x90 fs/open.c:1110
   do_syscall_64+0xf7/0x1c0 arch/x86/entry/common.c:290
   entry_SYSCALL_64_after_hwframe+0x49/0xbe
  [...]

After further debugging it turns out that we walk kallsyms while in parallel
we tear down a BPF program which contains subprograms that have been JITed
though the program itself has not been fully exposed and is eventually bailing
out with error.

The bpf_prog_kallsyms_del_subprogs() in bpf_prog_load()'s error path removes
the symbols, however, bpf_prog_free() tears down the JIT memory too early via
scheduled work. Instead, it needs to properly respect RCU grace period as the
kallsyms walk for BPF is under RCU.

Fix it by refactoring __bpf_prog_put()'s tear down and reuse it in our error
path where we defer final destruction when we have subprogs in the program.

Fixes: 7d1982b4e335 ("bpf: fix panic in prog load calls cleanup")
Fixes: 1c2a088a6626 ("bpf: x64: add JIT support for multi-function programs")
Reported-by: syzbot+710043c5d1d5b5013bc7@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: syzbot+710043c5d1d5b5013bc7@syzkaller.appspotmail.com
Link: https://lore.kernel.org/bpf/55f6367324c2d7e9583fa9ccf5385dcbba0d7a6e.1571752452.git.daniel@iogearbox.net

xdp: Handle device unregister for devmap_hash map type

It seems I forgot to add handling of devmap_hash type maps to the device
unregister hook for devmaps. This omission causes devices to not be
properly released, which causes hangs.

Fix this by adding the missing handler.

Fixes: 6f9d451ab1a3 ("xdp: Add devmap_hash map type for looking up devices by hashed index")
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191019111931.2981954-1-toke@redhat.com

r8152: add device id for Lenovo ThinkPad USB-C Dock Gen 2

This device is sold as 'ThinkPad USB-C Dock Gen 2 (40AS)'.
Chipset is RTL8153 and works with r8152.
Without this, the generic cdc_ether grabs the device, and the device jam
connected networks up when the machine suspends.

Signed-off-by: Kazutoshi Noguchi <noguchi.kazutosi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: fix IPSKB_FRAG_PMTU handling with fragmentation

This patch removes the iph field from the state structure, which is not
properly initialized. Instead, add a new field to make the "do we want
to set DF" be the state bit and move the code to set the DF flag from
ip_frag_next().

Joint work with Pablo and Linus.

Fixes: 19c3401a917b ("net: ipv4: place control buffer handling away from fragmentation iterators")
Reported-by: Patrick Schönthaler <patrick@notvads.ovh>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mlx5-fixes-2019-10-18' of git://git./linux/kernel/git/saeed/linux

Saeed Mahameed says:

====================
Mellanox, mlx5 kTLS fixes 18-10-2019

This series introduces kTLS related fixes to mlx5 driver from Tariq,
and two misc memory leak fixes form Navid Emamdoost.

Please pull and let me know if there is any problem.

I would appreciate it if you queue up kTLS fixes from the list below to
stable kernel v5.3 !

For -stable v4.13:
nett/mlx5: prevent memory leak in mlx5_fpga_conn_create_cq
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./linux/kernel/git/netdev/net

Pull networking fixes from David Miller:
"I was battling a cold after some recent trips, so quite a bit piled up
  meanwhile, sorry about that.

  Highlights:

   1) Fix fd leak in various bpf selftests, from Brian Vazquez.

   2) Fix crash in xsk when device doesn't support some methods, from
      Magnus Karlsson.

   3) Fix various leaks and use-after-free in rxrpc, from David Howells.

   4) Fix several SKB leaks due to confusion of who owns an SKB and who
      should release it in the llc code. From Eric Biggers.

   5) Kill a bunc of KCSAN warnings in TCP, from Eric Dumazet.

   6) Jumbo packets don't work after resume on r8169, as the BIOS resets
      the chip into non-jumbo mode during suspend. From Heiner Kallweit.

   7) Corrupt L2 header during MPLS push, from Davide Caratti.

   8) Prevent possible infinite loop in tc_ctl_action, from Eric
      Dumazet.

   9) Get register bits right in bcmgenet driver, based upon chip
      version. From Florian Fainelli.

  10) Fix mutex problems in microchip DSA driver, from Marek Vasut.

  11) Cure race between route lookup and invalidation in ipv4, from Wei
      Wang.

  12) Fix performance regression due to false sharing in 'net'
      structure, from Eric Dumazet"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (145 commits)
  net: reorder 'struct net' fields to avoid false sharing
  net: dsa: fix switch tree list
  net: ethernet: dwmac-sun8i: show message only when switching to promisc
  net: aquantia: add an error handling in aq_nic_set_multicast_list
  net: netem: correct the parent's backlog when corrupted packet was dropped
  net: netem: fix error path for corrupted GSO frames
  macb: propagate errors when getting optional clocks
  xen/netback: fix error path of xenvif_connect_data()
  net: hns3: fix mis-counting IRQ vector numbers issue
  net: usb: lan78xx: Connect PHY before registering MAC
  vsock/virtio: discard packets if credit is not respected
  vsock/virtio: send a credit update when buffer size is changed
  mlxsw: spectrum_trap: Push Ethernet header before reporting trap
  net: ensure correct skb->tstamp in various fragmenters
  net: bcmgenet: reset 40nm EPHY on energy detect
  net: bcmgenet: soft reset 40nm EPHYs before MAC init
  net: phy: bcm7xxx: define soft_reset for 40nm EPHY
  net: bcmgenet: don't set phydev->link from MAC
  net: Update address for MediaTek ethernet driver in MAINTAINERS
  ipv4: fix race condition between route lookup and invalidation
  ...

net: reorder 'struct net' fields to avoid false sharing

Intel test robot reported a ~7% regression on TCP_CRR tests
that they bisected to the cited commit.

Indeed, every time a new TCP socket is created or deleted,
the atomic counter net->count is touched (via get_net(net)
and put_net(net) calls)

So cpus might have to reload a contended cache line in
net_hash_mix(net) calls.

We need to reorder 'struct net' fields to move @hash_mix
in a read mostly cache line.

We move in the first cache line fields that can be
dirtied often.

We probably will have to address in a followup patch
the __randomize_layout that was added in linux-4.13,
since this might break our placement choices.

Fixes: 355b98553789 ("netns: provide pure entropy for net_hash_mix()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: fix switch tree list

If there are multiple switch trees on the device, only the last one
will be listed, because the arguments of list_add_tail are swapped.

Fixes: 83c0afaec7b7 ("net: dsa: Add new binding implementation")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: dwmac-sun8i: show message only when switching to promisc

Printing the info message every time more than the max number of mac
addresses are requested generates unnecessary log spam. Showing it only
when the hw is not already in promiscous mode is equally informative
without being annoying.

Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: aquantia: add an error handling in aq_nic_set_multicast_list

add an error handling in aq_nic_set_multicast_list, it may not
work when hw_multicast_list_set error; and at the same time
it will remove gcc Wunused-but-set-variable warning.

Signed-off-by: Chenwandun <chenwandun@huawei.com>
Reviewed-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'netem-fix-further-issues-with-packet-corruption'

Jakub Kicinski says:

====================
net: netem: fix further issues with packet corruption

This set is fixing two more issues with the netem packet corruption.

First patch (which was previously posted) avoids NULL pointer dereference
if the first frame gets freed due to allocation or checksum failure.
v2 improves the clarity of the code a little as requested by Cong.

Second patch ensures we don't return SUCCESS if the frame was in fact
dropped. Thanks to this commit message for patch 1 no longer needs the
"this will still break with a single-frame failure" disclaimer.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: netem: correct the parent's backlog when corrupted packet was dropped

If packet corruption failed we jump to finish_segs and return
NET_XMIT_SUCCESS. Seeing success will make the parent qdisc
increment its backlog, that's incorrect - we need to return
NET_XMIT_DROP.

Fixes: 6071bd1aa13e ("netem: Segment GSO packets on enqueue")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: netem: fix error path for corrupted GSO frames

To corrupt a GSO frame we first perform segmentation. We then
proceed using the first segment instead of the full GSO skb and
requeue the rest of the segments as separate packets.

If there are any issues with processing the first segment we
still want to process the rest, therefore we jump to the
finish_segs label.

Commit 177b8007463c ("net: netem: fix backlog accounting for
corrupted GSO frames") started using the pointer to the first
segment in the "rest of segments processing", but as mentioned
above the first segment may had already been freed at this point.

Backlog corrections for parent qdiscs have to be adjusted.

Fixes: 177b8007463c ("net: netem: fix backlog accounting for corrupted GSO frames")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

macb: propagate errors when getting optional clocks

The tx_clk, rx_clk, and tsu_clk are optional. Currently the macb driver
marks clock as not available if it receives an error when trying to get
a clock. This is wrong, because a clock controller might return
-EPROBE_DEFER if a clock is not available, but will eventually become
available.

In these cases, the driver would probe successfully but will never be
able to adjust the clocks, because the clocks were not available during
probe, but became available later.

For example, the clock controller for the ZynqMP is implemented in the
PMU firmware and the clocks are only available after the firmware driver
has been probed.

Use devm_clk_get_optional() in instead of devm_clk_get() to get the
optional clock and propagate all errors to the calling function.

Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xen/netback: fix error path of xenvif_connect_data()

xenvif_connect_data() calls module_put() in case of error. This is
wrong as there is no related module_get().

Remove the superfluous module_put().

Fixes: 279f438e36c0a7 ("xen-netback: Don't destroy the netdev until the vif is shut down")
Cc: <stable@vger.kernel.org> # 3.12
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix mis-counting IRQ vector numbers issue

Currently, the num_msi_left means the vector numbers of NIC,
but if the PF supported RoCE, it contains the vector numbers
of NIC and RoCE(Not expected).

This may cause interrupts lost in some case, because of the
NIC module used the vector resources which belongs to RoCE.

This patch adds a new variable num_nic_msi to store the vector
numbers of NIC, and adjust the default TQP numbers and rss_size
according to the value of num_nic_msi.

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'akpm' (patches from Andrew)

Merge misc fixes from Andrew Morton:
"Rather a lot of fixes, almost all affecting mm/"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (26 commits)
  scripts/gdb: fix debugging modules on s390
  kernel/events/uprobes.c: only do FOLL_SPLIT_PMD for uprobe register
  mm/thp: allow dropping THP from page cache
  mm/vmscan.c: support removing arbitrary sized pages from mapping
  mm/thp: fix node page state in split_huge_page_to_list()
  proc/meminfo: fix output alignment
  mm/init-mm.c: include <linux/mman.h> for vm_committed_as_batch
  mm/filemap.c: include <linux/ramfs.h> for generic_file_vm_ops definition
  mm: include <linux/huge_mm.h> for is_vma_temporary_stack
  zram: fix race between backing_dev_show and backing_dev_store
  mm/memcontrol: update lruvec counters in mem_cgroup_move_account
  ocfs2: fix panic due to ocfs2_wq is null
  hugetlbfs: don't access uninitialized memmaps in pfn_range_valid_gigantic()
  mm: memblock: do not enforce current limit for memblock_phys* family
  mm: memcg: get number of pages on the LRU list in memcgroup base on lru_zone_size
  mm/gup: fix a misnamed "write" argument, and a related bug
  mm/gup_benchmark: add a missing "w" to getopt string
  ocfs2: fix error handling in ocfs2_setattr()
  mm: memcg/slab: fix panic in __free_slab() caused by premature memcg pointer release
  mm/memunmap: don't access uninitialized memmap in memunmap_pages()
  ...

scripts/gdb: fix debugging modules on s390

Currently lx-symbols assumes that module text is always located at
module->core_layout->base, but s390 uses the following layout:

  +------+  <- module->core_layout->base
  | GOT  |
  +------+  <- module->core_layout->base + module->arch->plt_offset
  | PLT  |
  +------+  <- module->core_layout->base + module->arch->plt_offset +
  | TEXT |     module->arch->plt_size
  +------+

Therefore, when trying to debug modules on s390, all the symbol
addresses are skewed by plt_offset + plt_size.

Fix by adding plt_offset + plt_size to module_addr in
load_module_symbols().

Link: http://lkml.kernel.org/r/20191017085917.81791-1-iii@linux.ibm.com
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Kieran Bingham <kbingham@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/events/uprobes.c: only do FOLL_SPLIT_PMD for uprobe register

Attaching uprobe to text section in THP splits the PMD mapped page table
into PTE mapped entries.  On uprobe detach, we would like to regroup PMD
mapped page table entry to regain performance benefit of THP.

However, the regroup is broken For perf_event based trace_uprobe.  This
is because perf_event based trace_uprobe calls uprobe_unregister twice
on close: first in TRACE_REG_PERF_CLOSE, then in
TRACE_REG_PERF_UNREGISTER.  The second call will split the PMD mapped
page table entry, which is not the desired behavior.

Fix this by only use FOLL_SPLIT_PMD for uprobe register case.

Add a WARN() to confirm uprobe unregister never work on huge pages, and
abort the operation when this WARN() triggers.

Link: http://lkml.kernel.org/r/20191017164223.2762148-6-songliubraving@fb.com
Fixes: 5a52c9df62b4 ("uprobe: use FOLL_SPLIT_PMD instead of FOLL_SPLIT")
Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: William Kucharski <william.kucharski@oracle.com>
Cc: Yang Shi <yang.shi@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/thp: allow dropping THP from page cache

Once a THP is added to the page cache, it cannot be dropped via
/proc/sys/vm/drop_caches. Fix this issue with proper handling in
invalidate_mapping_pages().

Link: http://lkml.kernel.org/r/20191017164223.2762148-5-songliubraving@fb.com
Fixes: 99cb0dbd47a1 ("mm,thp: add read-only THP support for (non-shmem) FS")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Tested-by: Song Liu <songliubraving@fb.com>
Acked-by: Yang Shi <yang.shi@linux.alibaba.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/vmscan.c: support removing arbitrary sized pages from mapping

__remove_mapping() assumes that pages can only be either base pages or
HPAGE_PMD_SIZE. Ask the page what size it is.

Link: http://lkml.kernel.org/r/20191017164223.2762148-4-songliubraving@fb.com
Fixes: 99cb0dbd47a1 ("mm,thp: add read-only THP support for (non-shmem) FS")
Signed-off-by: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Song Liu <songliubraving@fb.com>
Acked-by: Yang Shi <yang.shi@linux.alibaba.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/thp: fix node page state in split_huge_page_to_list()

Make sure split_huge_page_to_list() handles the state of shmem THP and
file THP properly.

Link: http://lkml.kernel.org/r/20191017164223.2762148-3-songliubraving@fb.com
Fixes: 60fbf0ab5da1 ("mm,thp: stats for file backed THP")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Tested-by: Song Liu <songliubraving@fb.com>
Acked-by: Yang Shi <yang.shi@linux.alibaba.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

proc/meminfo: fix output alignment

Patch series "Fixes for THP in page cache", v2.

This patch (of 5):

Add extra space for FileHugePages and FilePmdMapped, so the output is
aligned with other rows.

Link: http://lkml.kernel.org/r/20191017164223.2762148-2-songliubraving@fb.com
Fixes: 60fbf0ab5da1 ("mm,thp: stats for file backed THP")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Tested-by: Song Liu <songliubraving@fb.com>
Acked-by: Yang Shi <yang.shi@linux.alibaba.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/init-mm.c: include <linux/mman.h> for vm_committed_as_batch

mm_init.c needs to include <linux/mman.h> for the definition of
vm_committed_as_batch. Fixes the following sparse warning:

mm/mm_init.c:141:5: warning: symbol 'vm_committed_as_batch' was not declared. Should it be static?

Link: http://lkml.kernel.org/r/20191016091509.26708-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/filemap.c: include <linux/ramfs.h> for generic_file_vm_ops definition

The generic_file_vm_ops is defined in <linux/ramfs.h> so include it to
fix the following warning:

mm/filemap.c:2717:35: warning: symbol 'generic_file_vm_ops' was not declared. Should it be static?

Link: http://lkml.kernel.org/r/20191008102311.25432-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: include <linux/huge_mm.h> for is_vma_temporary_stack

Include <linux/huge_mm.h> for the definition of is_vma_temporary_stack
to fix the following sparse warning:

mm/rmap.c:1673:6: warning: symbol 'is_vma_temporary_stack' was not declared. Should it be static?

Link: http://lkml.kernel.org/r/20191009151155.27763-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Qian Cai <cai@lca.pw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

zram: fix race between backing_dev_show and backing_dev_store

CPU0:        CPU1:
backing_dev_show        backing_dev_store
    ......    ......
    file = zram->backing_dev;
    down_read(&zram->init_lock);    down_read(&zram->init_init_lock)
    file_path(file, ...);    zram->backing_dev = backing_dev;
    up_read(&zram->init_lock);    up_read(&zram->init_lock);

gets the value of zram->backing_dev too early in backing_dev_show, which
resultin the value being NULL at the beginning, and not NULL later.

backtrace:
  d_path+0xcc/0x174
  file_path+0x10/0x18
  backing_dev_show+0x40/0xb4
  dev_attr_show+0x20/0x54
  sysfs_kf_seq_show+0x9c/0x10c
  kernfs_seq_show+0x28/0x30
  seq_read+0x184/0x488
  kernfs_fop_read+0x5c/0x1a4
  __vfs_read+0x44/0x128
  vfs_read+0xa0/0x138
  SyS_read+0x54/0xb4

Link: http://lkml.kernel.org/r/1571046839-16814-1-git-send-email-chenwandun@huawei.com
Signed-off-by: Chenwandun <chenwandun@huawei.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org> [4.14+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/memcontrol: update lruvec counters in mem_cgroup_move_account

Mapped, dirty and writeback pages are also counted in per-lruvec stats.
These counters needs update when page is moved between cgroups.

Currently is nobody *consuming* the lruvec versions of these counters and
that there is no user-visible effect.

Link: http://lkml.kernel.org/r/157112699975.7360.1062614888388489788.stgit@buzz
Fixes: 00f3ca2c2d66 ("mm: memcontrol: per-lruvec stats infrastructure")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ocfs2: fix panic due to ocfs2_wq is null

mount.ocfs2 failed when reading ocfs2 filesystem superblock encounters
an error.  ocfs2_initialize_super() returns before allocating ocfs2_wq.
ocfs2_dismount_volume() triggers the following panic.

  Oct 15 16:09:27 cnwarekv-205120 kernel: On-disk corruption discovered.Please run fsck.ocfs2 once the filesystem is unmounted.
  Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_read_locked_inode:537 ERROR: status = -30
  Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_init_global_system_inodes:458 ERROR: status = -30
  Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_init_global_system_inodes:491 ERROR: status = -30
  Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_initialize_super:2313 ERROR: status = -30
  Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_fill_super:1033 ERROR: status = -30
  ------------[ cut here ]------------
  Oops: 0002 [#1] SMP NOPTI
  CPU: 1 PID: 11753 Comm: mount.ocfs2 Tainted: G  E
        4.14.148-200.ckv.x86_64 #1
  Hardware name: Sugon H320-G30/35N16-US, BIOS 0SSDX017 12/21/2018
  task: ffff967af0520000 task.stack: ffffa5f05484000
  RIP: 0010:mutex_lock+0x19/0x20
  Call Trace:
    flush_workqueue+0x81/0x460
    ocfs2_shutdown_local_alloc+0x47/0x440 [ocfs2]
    ocfs2_dismount_volume+0x84/0x400 [ocfs2]
    ocfs2_fill_super+0xa4/0x1270 [ocfs2]
    ? ocfs2_initialize_super.isa.211+0xf20/0xf20 [ocfs2]
    mount_bdev+0x17f/0x1c0
    mount_fs+0x3a/0x160

Link: http://lkml.kernel.org/r/1571139611-24107-1-git-send-email-yili@winhong.com
Signed-off-by: Yi Li <yilikernel@gmail.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hugetlbfs: don't access uninitialized memmaps in pfn_range_valid_gigantic()

Uninitialized memmaps contain garbage and in the worst case trigger
kernel BUGs, especially with CONFIG_PAGE_POISONING.  They should not get
touched.

Let's make sure that we only consider online memory (managed by the
buddy) that has initialized memmaps.  ZONE_DEVICE is not applicable.

page_zone() will call page_to_nid(), which will trigger
VM_BUG_ON_PGFLAGS(PagePoisoned(page), page) with CONFIG_PAGE_POISONING
and CONFIG_DEBUG_VM_PGFLAGS when called on uninitialized memmaps.  This
can be the case when an offline memory block (e.g., never onlined) is
spanned by a zone.

Note: As explained by Michal in [1], alloc_contig_range() will verify
the range.  So it boils down to the wrong access in this function.

[1] http://lkml.kernel.org/r/20180423000943.GO17484@dhcp22.suse.cz

Link: http://lkml.kernel.org/r/20191015120717.4858-1-david@redhat.com
Fixes: f1dd2cd13c4b ("mm, memory_hotplug: do not associate hotadded memory to zones until online") [visible after d0dc12e86b319]
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: Michal Hocko <mhocko@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: <stable@vger.kernel.org> [4.13+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memblock: do not enforce current limit for memblock_phys* family

Until commit 92d12f9544b7 ("memblock: refactor internal allocation
functions") the maximal address for memblock allocations was forced to
memblock.current_limit only for the allocation functions returning
virtual address.  The changes introduced by that commit moved the limit
enforcement into the allocation core and as a result the allocation
functions returning physical address also started to limit allocations
to memblock.current_limit.

This caused breakage of etnaviv GPU driver:

  etnaviv etnaviv: bound 130000.gpu (ops gpu_ops)
  etnaviv etnaviv: bound 134000.gpu (ops gpu_ops)
  etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops)
  etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108
  etnaviv-gpu 130000.gpu: command buffer outside valid memory window
  etnaviv-gpu 134000.gpu: model: GC320, revision: 5007
  etnaviv-gpu 134000.gpu: command buffer outside valid memory window
  etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215
  etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0

Restore the behaviour of memblock_phys* family so that these functions
will not enforce memblock.current_limit.

Link: http://lkml.kernel.org/r/1570915861-17633-1-git-send-email-rppt@kernel.org
Fixes: 92d12f9544b7 ("memblock: refactor internal allocation functions")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reported-by: Adam Ford <aford173@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> [imx6q-logicpd]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcg: get number of pages on the LRU list in memcgroup base on lru_zone_size

Commit 1a61ab8038e72 ("mm: memcontrol: replace zone summing with
lruvec_page_state()") has made lruvec_page_state to use per-cpu counters
instead of calculating it directly from lru_zone_size with an idea that
this would be more effective.

Tim has reported that this is not really the case for their database
benchmark which is showing an opposite results where lruvec_page_state
is taking up a huge chunk of CPU cycles (about 25% of the system time
which is roughly 7% of total cpu cycles) on 5.3 kernels.  The workload
is running on a larger machine (96cpus), it has many cgroups (500) and
it is heavily direct reclaim bound.

Tim Chen said:

: The problem can also be reproduced by running simple multi-threaded
: pmbench benchmark with a fast Optane SSD swap (see profile below).
:
:
: 6.15%     3.08%  pmbench          [kernel.vmlinux]            [k] lruvec_lru_size
:             |
:             |--3.07%--lruvec_lru_size
:             |          |
:             |          |--2.11%--cpumask_next
:             |          |          |
:             |          |           --1.66%--find_next_bit
:             |          |
:             |           --0.57%--call_function_interrupt
:             |                     |
:             |                      --0.55%--smp_call_function_interrupt
:             |
:             |--1.59%--0x441f0fc3d009
:             |          _ops_rdtsc_init_base_freq
:             |          access_histogram
:             |          page_fault
:             |          __do_page_fault
:             |          handle_mm_fault
:             |          __handle_mm_fault
:             |          |
:             |           --1.54%--do_swap_page
:             |                     swapin_readahead
:             |                     swap_cluster_readahead
:             |                     |
:             |                      --1.53%--read_swap_cache_async
:             |                                __read_swap_cache_async
:             |                                alloc_pages_vma
:             |                                __alloc_pages_nodemask
:             |                                __alloc_pages_slowpath
:             |                                try_to_free_pages
:             |                                do_try_to_free_pages
:             |                                shrink_node
:             |                                shrink_node_memcg
:             |                                |
:             |                                |--0.77%--lruvec_lru_size
:             |                                |
:             |                                 --0.76%--inactive_list_is_low
:             |                                           |
:             |                                            --0.76%--lruvec_lru_size
:             |
:              --1.50%--measure_read
:                        page_fault
:                        __do_page_fault
:                        handle_mm_fault
:                        __handle_mm_fault
:                        do_swap_page
:                        swapin_readahead
:                        swap_cluster_readahead
:                        |
:                         --1.48%--read_swap_cache_async
:                                   __read_swap_cache_async
:                                   alloc_pages_vma
:                                   __alloc_pages_nodemask
:                                   __alloc_pages_slowpath
:                                   try_to_free_pages
:                                   do_try_to_free_pages
:                                   shrink_node
:                                   shrink_node_memcg
:                                   |
:                                   |--0.75%--inactive_list_is_low
:                                   |          |
:                                   |           --0.75%--lruvec_lru_size
:                                   |
:                                    --0.73%--lruvec_lru_size

The likely culprit is the cache traffic the lruvec_page_state_local
generates.  Dave Hansen says:

: I was thinking purely of the cache footprint.  If it's reading
: pn->lruvec_stat_local->count[idx] is three separate cachelines, so 192
: bytes of cache *96 CPUs = 18k of data, mostly read-only.  1 cgroup would
: be 18k of data for the whole system and the caching would be pretty
: efficient and all 18k would probably survive a tight page fault loop in
: the L1.  500 cgroups would be ~90k of data per CPU thread which doesn't
: fit in the L1 and probably wouldn't survive a tight page fault loop if
: both logical threads were banging on different cgroups.
:
: It's just a theory, but it's why I noted the number of cgroups when I
: initially saw this show up in profiles

Fix the regression by partially reverting the said commit and calculate
the lru size explicitly.

Link: http://lkml.kernel.org/r/20190905071034.16822-1-honglei.wang@oracle.com
Fixes: 1a61ab8038e72 ("mm: memcontrol: replace zone summing with lruvec_page_state()")
Signed-off-by: Honglei Wang <honglei.wang@oracle.com>
Reported-by: Tim Chen <tim.c.chen@linux.intel.com>
Acked-by: Tim Chen <tim.c.chen@linux.intel.com>
Tested-by: Tim Chen <tim.c.chen@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: <stable@vger.kernel.org> [5.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>