OSDN Git Service
Rafael J. Wysocki [Thu, 26 Oct 2017 10:12:22 +0000 (12:12 +0200)]
PCI / PM: Take SMART_SUSPEND driver flag into account
Make the PCI bus type take DPM_FLAG_SMART_SUSPEND into account in its
system-wide PM callbacks and make sure that all code that should not
run in parallel with pci_pm_runtime_resume() is executed in the "late"
phases of system suspend, freeze and poweroff transitions.
[Note that the pm_runtime_suspended() check in pci_dev_keep_suspended()
is an optimization, because if is not passed, all of the subsequent
checks may be skipped and some of them are much more overhead in
general.]
Also use the observation that if the device is in runtime suspend
at the beginning of the "late" phase of a system-wide suspend-like
transition, its state cannot change going forward (runtime PM is
disabled for it at that time) until the transition is over and the
subsequent system-wide PM callbacks should be skipped for it (as
they generally assume the device to not be suspended), so add checks
for that in pci_pm_suspend_late/noirq(), pci_pm_freeze_late/noirq()
and pci_pm_poweroff_late/noirq().
Moreover, if pci_pm_resume_noirq() or pci_pm_restore_noirq() is
called during the subsequent system-wide resume transition and if
the device was left in runtime suspend previously, its runtime PM
status needs to be changed to "active" as it is going to be put
into the full-power state, so add checks for that too to these
functions.
In turn, if pci_pm_thaw_noirq() runs after the device has been
left in runtime suspend, the subsequent "thaw" callbacks need
to be skipped for it (as they may not work correctly with a
suspended device), so set the power.direct_complete flag for the
device then to make the PM core skip those callbacks.
In addition to the above add a core helper for checking if
DPM_FLAG_SMART_SUSPEND is set and the device runtime PM status is
"suspended" at the same time, which is done quite often in the new
code (and will be done elsewhere going forward too).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Rafael J. Wysocki [Thu, 26 Oct 2017 10:12:16 +0000 (12:12 +0200)]
PCI / PM: Drop unnecessary invocations of pcibios_pm_ops callbacks
The only user of non-empty pcibios_pm_ops is s390 and it only uses
"noirq" callbacks, so drop the invocations of the other pcibios_pm_ops
callbacks from the PCI PM code.
That will allow subsequent changes to be somewhat simpler.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Rafael J. Wysocki [Thu, 26 Oct 2017 10:12:08 +0000 (12:12 +0200)]
PM / core: Add SMART_SUSPEND driver flag
Define and document a SMART_SUSPEND flag to instruct bus types and PM
domains that the system suspend callbacks provided by the driver can
cope with runtime-suspended devices, so from the driver's perspective
it should be safe to leave devices in runtime suspend during system
suspend.
Setting that flag may also cause middle-layer code (bus types,
PM domains etc.) to skip invocations of the ->suspend_late and
->suspend_noirq callbacks provided by the driver if the device
is in runtime suspend at the beginning of the "late" phase of
the system-wide suspend transition, in which case the driver's
system-wide resume callbacks may be invoked back-to-back with
its ->runtime_suspend callback, so the driver has to be able to
cope with that too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Rafael J. Wysocki [Wed, 25 Oct 2017 12:16:46 +0000 (14:16 +0200)]
PCI / PM: Use the NEVER_SKIP driver flag
Replace the PCI-specific flag PCI_DEV_FLAGS_NEEDS_RESUME with the
PM core's DPM_FLAG_NEVER_SKIP one everywhere and drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Rafael J. Wysocki [Wed, 25 Oct 2017 12:12:29 +0000 (14:12 +0200)]
PM / core: Add NEVER_SKIP and SMART_PREPARE driver flags
The motivation for this change is to provide a way to work around
a problem with the direct-complete mechanism used for avoiding
system suspend/resume handling for devices in runtime suspend.
The problem is that some middle layer code (the PCI bus type and
the ACPI PM domain in particular) returns positive values from its
system suspend ->prepare callbacks regardless of whether the driver's
->prepare returns a positive value or 0, which effectively prevents
drivers from being able to control the direct-complete feature.
Some drivers need that control, however, and the PCI bus type has
grown its own flag to deal with this issue, but since it is not
limited to PCI, it is better to address it by adding driver flags at
the core level.
To that end, add a driver_flags field to struct dev_pm_info for flags
that can be set by device drivers at the probe time to inform the PM
core and/or bus types, PM domains and so on on the capabilities and/or
preferences of device drivers. Also add two static inline helpers
for setting that field and testing it against a given set of flags
and make the driver core clear it automatically on driver remove
and probe failures.
Define and document two PM driver flags related to the direct-
complete feature: NEVER_SKIP and SMART_PREPARE that can be used,
respectively, to indicate to the PM core that the direct-complete
mechanism should never be used for the device and to inform the
middle layer code (bus types, PM domains etc) that it can only
request the PM core to use the direct-complete mechanism for
the device (by returning a positive value from its ->prepare
callback) if it also has been requested by the driver.
While at it, make the core check pm_runtime_suspended() when
setting power.direct_complete so that it doesn't need to be
checked by ->prepare callbacks.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Rafael J. Wysocki [Mon, 6 Nov 2017 12:54:47 +0000 (13:54 +0100)]
Merge branch 'acpi-pm' into pm-core
Rafael J. Wysocki [Mon, 16 Oct 2017 01:29:55 +0000 (03:29 +0200)]
ACPI / LPSS: Consolidate runtime PM and system sleep handling
Move the LPSS-specific code from acpi_lpss_runtime_suspend()
and acpi_lpss_runtime_resume() into separate functions,
acpi_lpss_suspend() and acpi_lpss_resume(), respectively, and
make acpi_lpss_suspend_late() and acpi_lpss_resume_early() use
them too in order to unify the runtime PM and system sleep
handling in the LPSS driver.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Kees Cook [Mon, 16 Oct 2017 23:20:55 +0000 (16:20 -0700)]
PM / core: Convert timers to use timer_setup()
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Removes test of .data field, since
that will be going away.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki [Fri, 13 Oct 2017 13:25:39 +0000 (15:25 +0200)]
PM / core: Fix kerneldoc comments of four functions
Fix the kerneldoc comments of __device_suspend_noirq(),
__device_suspend_late() and __device_suspend() where the function
names in kerneldoc don't match the actual names of the functions.
Also fix the device_resume_noirq() kerneldoc comment which mentions
"early resume" instead of "noirq resume" incorrectly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Rafael J. Wysocki [Sat, 21 Oct 2017 11:09:18 +0000 (13:09 +0200)]
Merge branch 'pm-sleep' into pm-core
Rafael J. Wysocki [Sat, 14 Oct 2017 15:43:15 +0000 (17:43 +0200)]
ACPI / PM: Combine device suspend routines
On top of a previous change getting rid of the PM QoS flag
PM_QOS_FLAG_REMOTE_WAKEUP, combine two ACPI device suspend routines,
acpi_dev_runtime_suspend() and acpi_dev_suspend_late(), into one,
acpi_dev_suspend(), to eliminate some code duplication.
It also avoids enabling wakeup for devices handled by the ACPI
LPSS middle layer on driver removal.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Rafael J. Wysocki [Mon, 16 Oct 2017 22:29:58 +0000 (00:29 +0200)]
Merge branch 'pm-qos' into acpi-pm
Rafael J. Wysocki [Fri, 13 Oct 2017 13:27:24 +0000 (15:27 +0200)]
PM / QoS: Drop PM_QOS_FLAG_REMOTE_WAKEUP
The PM QoS flag PM_QOS_FLAG_REMOTE_WAKEUP is not used consistently
and the vast majority of code simply assumes that remote wakeup
should be enabled for devices in runtime suspend if they can
generate wakeup signals, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Ulf Hansson [Tue, 3 Oct 2017 07:11:07 +0000 (09:11 +0200)]
PM / sleep: Remove pm_complete_with_resume_check()
According to recent changes for ACPI, the are longer any users of
pm_complete_with_resume_check(), thus let's drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki [Wed, 11 Oct 2017 13:39:38 +0000 (15:39 +0200)]
Merge branch 'acpi-pm' into pm-sleep
Srinivas Pandruvada [Thu, 5 Oct 2017 23:24:03 +0000 (16:24 -0700)]
ACPI / LPIT: Add Low Power Idle Table (LPIT) support
Add functionality to read LPIT table, which provides:
- Sysfs interface to read residency counters via
/sys/devices/system/cpu/cpuidle/low_power_idle_cpu_residency_us
/sys/devices/system/cpu/cpuidle/low_power_idle_system_residency_us
Here the count "low_power_idle_cpu_residency_us" shows the time spent
by CPU package in low power state. This is read via MSR interface,
which points to MSR for PKG C10.
Here the count "low_power_idle_system_residency_us" show the count the
system was in low power state. This is read via MMIO interface. This
is mapped to SLP_S0 residency on modern Intel systems. This residency
is achieved only when CPU is in PKG C10 and all functional blocks are
in low power state.
It is possible that none of the above counters present or anyone of the
counter present or all counters present.
For example: On my Kabylake system both of the above counters present.
After suspend to idle these counts updated and prints:
6916179
6998564
This counter can be read by tools like turbostat to display. Or it can
be used to debug, if modern systems are reaching desired low power state.
- Provides an interface to read residency counter memory address
This address can be used to get the base address of PMC memory
mapped IO. This is utilized by intel_pmc_core driver to print
more debug information.
In addition, to avoid code duplication to read iomem, removed the read of
iomem from acpi_os_read_memory() in osl.c and made a common function
acpi_os_read_iomem(). This new function is used for reading iomem in
in both osl.c and acpi_lpit.c.
Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Ulf Hansson [Tue, 3 Oct 2017 07:11:08 +0000 (09:11 +0200)]
ACPI / PM: Split code validating need for runtime resume in ->prepare()
Move the code dealing with validation of whether runtime resuming the
device is needed during system suspend.
In this way it becomes more clear for what circumstances ACPI is prevented
from trying the direct_complete path.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Ulf Hansson [Tue, 3 Oct 2017 07:11:06 +0000 (09:11 +0200)]
ACPI / PM: Restore acpi_subsys_complete()
Commit
58a1fbbb2ee8 (PM / PCI / ACPI: Kick devices that might have
been reset by firmware), made PCI's and ACPI's ->complete() callbacks
to be assigned to a new API called pm_complete_with_resume_check(),
which was introduced in the same change.
Later it turned out that using pm_complete_with_resume_check() wasn't
good enough for PCI, as it needed additional PCI specific checks,
before deciding whether runtime resuming the device is needed when
running the ->complete() callback.
This leaves ACPI as the only user of pm_complete_with_resume_check().
Therefore let's restore ACPI's acpi_subsys_complete(), which was
dropped in commit
58a1fbbb2ee8 (PM / PCI / ACPI: Kick devices that
might have been reset by firmware).
This enables us to remove the pm_complete_with_resume_check() API in
a following change, but it also enables ACPI to add more ACPI
specific checks in acpi_subsys_complete() if that turns out to be
necessary.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki [Tue, 10 Oct 2017 16:49:22 +0000 (18:49 +0200)]
ACPI / PM: Combine two identical device resume routines
Notice that acpi_dev_runtime_resume() and acpi_dev_resume_early() are
actually literally identical after some more-or-less recent changes,
so rename acpi_dev_runtime_resume() to acpi_dev_resume(), use it
everywhere instead of acpi_dev_resume_early() and drop the latter.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Fri, 6 Oct 2017 07:08:34 +0000 (09:08 +0200)]
ACPI / PM: Remove stale function header
acpi_dev_pm_get_node() isn't used or implemented, so remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki [Mon, 9 Oct 2017 12:20:07 +0000 (14:20 +0200)]
Merge back suspend/resume/hibernate material for v4.15.
Linus Torvalds [Mon, 9 Oct 2017 03:53:29 +0000 (20:53 -0700)]
Linux 4.14-rc4
Linus Torvalds [Sat, 7 Oct 2017 19:34:16 +0000 (12:34 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
- a couple of serious fixes: use after free and blacklist for WRITE
SAME
- one error leg fix: write_pending failure
- one user experience problem: do not override max_sectors_kb
- one minor unused function removal
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ibmvscsis: Fix write_pending failure path
scsi: libiscsi: Remove iscsi_destroy_session
scsi: libiscsi: Fix use-after-free race during iscsi_session_teardown
scsi: sd: Do not override max_sectors_kb sysfs setting
scsi: sd: Implement blacklist option for WRITE SAME w/ UNMAP
Linus Torvalds [Sat, 7 Oct 2017 17:07:51 +0000 (10:07 -0700)]
Merge branch 'i2c/for-current-4.14' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has three driver fixes for the newly introduced drivers and one ID
addition for the i801 driver"
* 'i2c/for-current-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-stm32f7: make structure stm32f7_setup static const
i2c: ensure termination of *_device_id tables
i2c: i801: Add support for Intel Cedar Fork
i2c: stm32f7: fix setup structure
Linus Torvalds [Sat, 7 Oct 2017 17:03:03 +0000 (10:03 -0700)]
Merge tag 'mmc-v4.14-rc3' of git://git./linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix driver strength selection when selecting hs400es
- Delete bounce buffer handling:
This change fixes a problem related to how bounce buffers are being
allocated. However, instead of trying to fix that, let's just
remove the mmc bounce buffer code altogether, as it has practically
no use.
MMC host:
- meson-gx: A couple of fixes related to clock/phase/tuning
- sdhci-xenon: Fix clock resource by adding an optional bus clock"
* tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-xenon: Fix clock resource by adding an optional bus clock
mmc: meson-gx: include tx phase in the tuning process
mmc: meson-gx: fix rx phase reset
mmc: meson-gx: make sure the clock is rounded down
mmc: Delete bounce buffer handling
mmc: core: add driver strength selection when selecting hs400es
Linus Torvalds [Sat, 7 Oct 2017 00:59:32 +0000 (17:59 -0700)]
Merge tag 'hwmon-for-linus-v4.14-rc4' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix up error path in xgene driver"
* tag 'hwmon-for-linus-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (xgene) Fix up error handling path mixup in 'xgene_hwmon_probe()'
Linus Torvalds [Fri, 6 Oct 2017 23:25:08 +0000 (16:25 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
- build fix to export the clk_bulk_prepare() symbol
- suspend fix for Samsung Exynos SoCs where we need to keep clks on
across suspend
- two critical clk markings for clks that shouldn't ever turn off on
Rockchip SoCs
- a fix for a copy-paste mistake on Rockchip rk3128 causing some clks
to touch the same bit and trample over one another
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: samsung: exynos4: Enable VPLL and EPLL clocks for suspend/resume cycle
clk: Export clk_bulk_prepare()
clk: rockchip: add sclk_timer5 as critical clock on rk3128
clk: rockchip: fix up rk3128 pvtm and mipi_24m gate regs error
clk: rockchip: add pclk_pmu as critical clock on rk3128
Linus Torvalds [Fri, 6 Oct 2017 22:57:08 +0000 (15:57 -0700)]
Merge tag 'arc-4.14-rc4' of git://git./linux/kernel/git/vgupta/arc
Pull ARC udpates from Vineet Gupta:
- updates for various platforms
- boot log updates for upcoming HS48 family of cores (dual issue)
* tag 'arc-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [plat-hsdk]: Add reset controller node to manage ethernet reset
ARC: [plat-hsdk]: Temporary fix to set CPU frequency to 1GHz
ARC: fix allnoconfig build warning
ARCv2: boot log: identify HS48 cores (dual issue)
ARC: boot log: decontaminate ARCv2 ISA_CONFIG register
arc: remove redundant UTS_MACHINE define in arch/arc/Makefile
ARC: [plat-eznps] Update platform maintainer as Noam left
ARC: [plat-hsdk] use actual clk driver to manage cpu clk
ARC: [*defconfig] Reenable soft lock-up detector
ARC: [plat-axs10x] sdio: Temporary fix of sdio ciu frequency
ARC: [plat-hsdk] sdio: Temporary fix of sdio ciu frequency
ARC: [plat-axs103] Add temporary quirk to reset ethernet IP
Linus Torvalds [Fri, 6 Oct 2017 22:53:36 +0000 (15:53 -0700)]
Merge tag 'xfs-4.14-fixes-4' of git://git./fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
- fix a race between overlapping copy on write aio
- fix cow fork swapping when we defragment reflinked files
* tag 'xfs-4.14-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: handle racy AIO in xfs_reflink_end_cow
xfs: always swap the cow forks when swapping extents
Linus Torvalds [Fri, 6 Oct 2017 19:13:50 +0000 (12:13 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes for this series. This contains:
- NVMe pull request from Christoph, one uuid attribute fix, and one
fix for the controller memory buffer address for remapped BARs.
- use-after-free fix for bsg, from Benjamin Block.
- bcache race/use-after-free fix for a list traversal, fixing a
regression in this merge window. From Coly Li.
- null_blk change configfs dependency change from a 'depends' to a
'select'. This is a change from this merge window as well. From me.
- nbd signal fix from Josef, fixing a regression introduced with the
status code changes.
- nbd MAINTAINERS mailing list entry update.
- blk-throttle stall fix from Joseph Qi.
- blk-mq-debugfs fix from Omar, fixing an issue where we don't
register the IO scheduler debugfs directory, if the driver is
loaded with it. Only shows up if you switch through the sysfs
interface"
* 'for-linus' of git://git.kernel.dk/linux-block:
bsg-lib: fix use-after-free under memory-pressure
nvme-pci: Use PCI bus address for data/queues in CMB
blk-mq-debugfs: fix device sched directory for default scheduler
null_blk: change configfs dependency to select
blk-throttle: fix possible io stall when upgrade to max
MAINTAINERS: update list for NBD
nbd: fix -ERESTARTSYS handling
nvme: fix visibility of "uuid" ns attribute
bcache: use llist_for_each_entry_safe() in __closure_wake_up()
Linus Torvalds [Fri, 6 Oct 2017 19:07:09 +0000 (12:07 -0700)]
Merge tag 'pci-v4.14-fixes-4' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Fix legacy IDE probe issues exposed by recent PCI core IRQ mapping
changes (Bartlomiej Zolnierkiewicz, Lorenzo Pieralisi)"
* tag 'pci-v4.14-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
ide: fix IRQ assignment for PCI bus order probing
ide: pci: free PCI BARs on initialization failure
ide: free hwif->portdev on hwif_init() failure
Linus Torvalds [Fri, 6 Oct 2017 18:31:46 +0000 (11:31 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Bring initialisation of user space undefined instruction handling
early (core_initcall) since late_initcall() happens after modprobe in
initramfs is invoked. Similar fix for fpsimd initialisation
- Increase the kernel stack when KASAN is enabled
- Bring the PCI ACS enabling earlier via the
iort_init_platform_devices()
- Fix misleading data abort address printing (decimal vs hex)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Ensure fpsimd support is ready before userspace is active
arm64: Ensure the instruction emulation is ready for userspace
arm64: Use larger stacks when KASAN is selected
ACPI/IORT: Fix PCI ACS enablement
arm64: fix misleading data abort decoding
Linus Torvalds [Fri, 6 Oct 2017 18:28:34 +0000 (11:28 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
- fix PPC XIVE interrupt delivery
- fix x86 RCU breakage from asynchronous page faults when built without
PREEMPT_COUNT
- fix x86 build with -frecord-gcc-switches
- fix x86 build without X86_LOCAL_APIC
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: add X86_LOCAL_APIC dependency
x86/kvm: Move kvm_fastop_exception to .fixup section
kvm/x86: Avoid async PF preempting the kernel incorrectly
KVM: PPC: Book3S: Fix server always zero from kvmppc_xive_get_xive()
Linus Torvalds [Fri, 6 Oct 2017 18:25:55 +0000 (11:25 -0700)]
Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"This is a pretty small pull request. Only 6 patches in total. There
are no outstanding -rc patches on the mailing list after this pull
request, so only if some new issues are discovered in the remainder of
the rc cycles will you hear from me again.
Summary:
- a fix for iwpm netlink usage
- a fix for error unwinding in mlx5
- two fixes to vlan handling in qedr
- a couple small i40iw fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
i40iw: Fix port number for query QP
i40iw: Add missing memory barriers
RDMA/qedr: Parse vlan priority as sl
RDMA/qedr: Parse VLAN ID correctly and ignore the value of zero
IB/mlx5: Fix label order in error path handling
RDMA/iwpm: Properly mark end of NL messages
Linus Torvalds [Fri, 6 Oct 2017 16:03:08 +0000 (09:03 -0700)]
Merge branch 'for-4.14-rc4' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Two more fixes for bugs introduced in 4.13.
The sector_t problem with 32bit architecture and !LBDAF config seems
serious but the number of affected deployments is hopefully low.
The clashing status bits could lead to a confusing in-memory state of
the whole-filesystem operations if used with the quota override sysfs
knob"
* 'for-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix overlap of fs_info::flags values
btrfs: avoid overflow when sector_t is 32 bit
Linus Torvalds [Fri, 6 Oct 2017 16:01:45 +0000 (09:01 -0700)]
Merge tag 'ceph-for-4.14-rc4' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"Two fixups for CephFS snapshot-handling patches in -rc1"
* tag 'ceph-for-4.14-rc4' of git://github.com/ceph/ceph-client:
ceph: fix __choose_mds() for LSSNAP request
ceph: properly queue cap snap for newly created snap realm
Eugeniy Paltsev [Fri, 22 Sep 2017 16:49:11 +0000 (19:49 +0300)]
ARC: [plat-hsdk]: Add reset controller node to manage ethernet reset
DW ethernet controller on HSDK hangs sometimes after SW reset, so
add reset node to make possible to reset DW ethernet controller HW.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Linus Torvalds [Fri, 6 Oct 2017 15:52:53 +0000 (08:52 -0700)]
Merge branch 'overlayfs-linus' of git://git./linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"Fix a regression in 4.14 and one in 4.13. The latter is a case when
Docker is doing something it really shouldn't and gets away with it.
We now print a warning instead of erroring out.
There are also fixes to several error paths"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: fix regression caused by exclusive upper/work dir protection
ovl: fix missing unlock_rename() in ovl_do_copy_up()
ovl: fix dentry leak in ovl_indexdir_cleanup()
ovl: fix dput() of ERR_PTR in ovl_cleanup_index()
ovl: fix error value printed in ovl_lookup_index()
ovl: fix may_write_real() for overlayfs directories
Linus Torvalds [Fri, 6 Oct 2017 15:47:21 +0000 (08:47 -0700)]
Merge tag 'powerpc-4.14-4' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Nine small fixes, really nothing that stands out.
A work-around for a spurious MCE on Power9. A CXL fault handling fix,
some fixes to the new XIVE code, and a fix to the new 32-bit
STRICT_KERNEL_RWX code.
Fixes for old code/stable: an fix to an incorrect TLB flush on boot
but not on any current machines, a compile error on 4xx and a fix to
memory hotplug when using radix (Power9).
Thanks to: Anton Blanchard, Cédric Le Goater, Christian Lamparter,
Christophe Leroy, Christophe Lombard, Guenter Roeck, Jeremy Kerr,
Michael Neuling, Nicholas Piggin"
* tag 'powerpc-4.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: Increase memory block size to 1GB on radix
powerpc/mm: Call flush_tlb_kernel_range with interrupts enabled
powerpc/xive: Clear XIVE internal structures when a CPU is removed
powerpc/xive: Fix IPI reset
powerpc/4xx: Fix compile error with 64K pages on 40x, 44x
powerpc: Fix action argument for cpufeatures-based TLB flush
cxl: Fix memory page not handled
powerpc: Fix workaround for spurious MCE on POWER9
powerpc: Handle MCE on POWER9 with only DSISR bit 30 set
Linus Torvalds [Fri, 6 Oct 2017 15:42:06 +0000 (08:42 -0700)]
Merge tag 'drm-fixes-for-v4.14-rc4' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Some i915 fixes from the last two weeks (as they were on a strange
base and I just waited for rc3), also a single sun4i hdmi fix"
* tag 'drm-fixes-for-v4.14-rc4' of git://people.freedesktop.org/~airlied/linux:
drm/i915/glk: Fix DMC/DC state idleness calculation
drm/i915/cnl: Reprogram DMC firmware after S3/S4 resume
drm/i915: Fix DDI PHY init if it was already on
drm/sun4i: hdmi: Disable clks in bind function error path and unbind function
drm/i915/bios: ignore HDMI on port A
drm/i915: remove redundant variable hw_check
drm/i915: always update ELD connector type after get modes
Linus Torvalds [Fri, 6 Oct 2017 15:36:41 +0000 (08:36 -0700)]
Merge branch 'core-watchdog-for-linus' of git://git./linux/kernel/git/tip/tip
Pull watchddog clean-up and fixes from Thomas Gleixner:
"The watchdog (hard/softlockup detector) code is pretty much broken in
its current state. The patch series addresses this by removing all
duct tape and refactoring it into a workable state.
The reasons why I ask for inclusion that late in the cycle are:
1) The code causes lockdep splats vs. hotplug locking which get
reported over and over. Unfortunately there is no easy fix.
2) The risk of breakage is minimal because it's already broken
3) As 4.14 is a long term stable kernel, I prefer to have working
watchdog code in that and the lockdep issues resolved. I wouldn't
ask you to pull if 4.14 wouldn't be a LTS kernel or if the
solution would be easy to backport.
4) The series was around before the merge window opened, but then got
delayed due to the UP failure caused by the for_each_cpu()
surprise which we discussed recently.
Changes vs. V1:
- Addressed your review points
- Addressed the warning in the powerpc code which was discovered late
- Changed two function names which made sense up to a certain point
in the series. Now they match what they do in the end.
- Fixed a 'unused variable' warning, which got not detected by the
intel robot. I triggered it when trying all possible related config
combinations manually. Randconfig testing seems not random enough.
The changes have been tested by and reviewed by Don Zickus and tested
and acked by Micheal Ellerman for powerpc"
* 'core-watchdog-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
watchdog/core: Put softlockup_threads_initialized under ifdef guard
watchdog/core: Rename some softlockup_* functions
powerpc/watchdog: Make use of watchdog_nmi_probe()
watchdog/core, powerpc: Lock cpus across reconfiguration
watchdog/core, powerpc: Replace watchdog_nmi_reconfigure()
watchdog/hardlockup/perf: Fix spelling mistake: "permanetely" -> "permanently"
watchdog/hardlockup/perf: Cure UP damage
watchdog/hardlockup: Clean up hotplug locking mess
watchdog/hardlockup/perf: Simplify deferred event destroy
watchdog/hardlockup/perf: Use new perf CPU enable mechanism
watchdog/hardlockup/perf: Implement CPU enable replacement
watchdog/hardlockup/perf: Implement init time detection of perf
watchdog/hardlockup/perf: Implement init time perf validation
watchdog/core: Get rid of the racy update loop
watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage
watchdog/sysctl: Clean up sysctl variable name space
watchdog/sysctl: Get rid of the #ifdeffery
watchdog/core: Clean up header mess
watchdog/core: Further simplify sysctl handling
watchdog/core: Get rid of the thread teardown/setup dance
...
Suzuki K Poulose [Fri, 6 Oct 2017 13:16:53 +0000 (14:16 +0100)]
arm64: Ensure fpsimd support is ready before userspace is active
We register the pm/hotplug callbacks for FPSIMD as late_initcall,
which happens after the userspace is active (from initramfs via
populate_rootfs, a rootfs_initcall). Make sure we are ready even
before the userspace could potentially use it, by promoting to
a core_initcall.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Suzuki K Poulose [Fri, 6 Oct 2017 13:16:52 +0000 (14:16 +0100)]
arm64: Ensure the instruction emulation is ready for userspace
We trap and emulate some instructions (e.g, mrs, deprecated instructions)
for the userspace. However the handlers for these are registered as
late_initcalls and the userspace could be up and running from the initramfs
by that time (with populate_rootfs, which is a rootfs_initcall()). This
could cause problems for the early applications ending up in failure
like :
[ 11.152061] modprobe[93]: undefined instruction: pc=
0000ffff8ca48ff4
This patch promotes the specific calls to core_initcalls, which are
guaranteed to be completed before we hit userspace.
Cc: stable@vger.kernel.org
Cc: Dave Martin <dave.martin@arm.com>
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: James Morse <james.morse@arm.com>
Reported-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Anton Blanchard [Thu, 7 Sep 2017 05:05:51 +0000 (15:05 +1000)]
powerpc/powernv: Increase memory block size to 1GB on radix
Memory hot unplug on PowerNV radix hosts is broken. Our memory block
size is 256MB but since we map the linear region with very large
pages, each pte we tear down maps 1GB.
A hot unplug of one 256MB memory block results in 768MB of memory
getting unintentionally unmapped. At this point we are likely to oops.
Fix this by increasing our memory block size to 1GB on PowerNV radix
hosts.
Fixes:
4b5d62ca17a1 ("powerpc/mm: add radix__remove_section_mapping()")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Dave Airlie [Fri, 6 Oct 2017 01:09:47 +0000 (11:09 +1000)]
Merge tag 'drm-misc-fixes-2017-10-05' of git://anongit.freedesktop.org/git/drm-misc into drm-fixes
One bugfix in sun4i for 4.14
* tag 'drm-misc-fixes-2017-10-05' of git://anongit.freedesktop.org/git/drm-misc:
drm/sun4i: hdmi: Disable clks in bind function error path and unbind function
Dave Airlie [Fri, 6 Oct 2017 01:09:29 +0000 (11:09 +1000)]
Merge tag 'drm-intel-fixes-2017-10-04' of git://anongit.freedesktop.org/git/drm-intel into drm-fixes
drm/i915 fixes for 4.14-rc4:
All 3 highest GLK bugs fixed by Imre:
- GLK drv reload - Fix DDI Phy init if it was already on.
- GLK suspend resume - Reprogram DMC firmware after s3/s4.
- GLK DC states - Fix idleness calculation.
* tag 'drm-intel-fixes-2017-10-04' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915/glk: Fix DMC/DC state idleness calculation
drm/i915/cnl: Reprogram DMC firmware after S3/S4 resume
drm/i915: Fix DDI PHY init if it was already on
Linus Torvalds [Thu, 5 Oct 2017 22:51:37 +0000 (15:51 -0700)]
Merge tag 'pm-4.14-rc4' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"This fixes a code ordering issue in the main suspend-to-idle loop that
causes some "low power S0 idle" conditions to be incorrectly reported
as unmet with suspend/resume debug messages enabled"
* tag 'pm-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / s2idle: Invoke the ->wake() platform callback earlier
Rafael J. Wysocki [Thu, 5 Oct 2017 22:24:14 +0000 (00:24 +0200)]
Merge branch 'pm-sleep'
* pm-sleep:
PM / s2idle: Invoke the ->wake() platform callback earlier
Linus Torvalds [Thu, 5 Oct 2017 22:17:40 +0000 (15:17 -0700)]
Merge tag 'for-4.14/dm-fixes' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a stable fix for the alignment of the event number reported at the
end of the 'DM_LIST_DEVICES' ioctl.
- a couple stable fixes for the DM crypt target.
- a DM raid health status reporting fix.
* tag 'for-4.14/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm raid: fix incorrect status output at the end of a "recover" process
dm crypt: reject sector_size feature if device length is not aligned to it
dm crypt: fix memory leak in crypt_ctr_cipher_old()
dm ioctl: fix alignment of event number in the device list
Jonathan Brassow [Mon, 2 Oct 2017 22:17:35 +0000 (17:17 -0500)]
dm raid: fix incorrect status output at the end of a "recover" process
There are three important fields that indicate the overall health and
status of an array: dev_health, sync_ratio, and sync_action. They tell
us the condition of the devices in the array, and the degree to which
the array is synchronized.
This commit fixes a condition that is reported incorrectly. When a member
of the array is being rebuilt or a new device is added, the "recover"
process is used to synchronize it with the rest of the array. When the
process is complete, but the sync thread hasn't yet been reaped, it is
possible for the state of MD to be:
mddev->recovery = [ MD_RECOVERY_RUNNING MD_RECOVERY_RECOVER MD_RECOVERY_DONE ]
curr_resync_completed = <max dev size> (but not MaxSector)
and all rdevs to be In_sync.
This causes the 'array_in_sync' output parameter that is passed to
rs_get_progress() to be computed incorrectly and reported as 'false' --
or not in-sync. This in turn causes the dev_health status characters to
be reported as all 'a', rather than the proper 'A'.
This can cause erroneous output for several seconds at a time when tools
will want to be checking the condition due to events that are raised at
the end of a sync process. Fix this by properly calculating the
'array_in_sync' return parameter in rs_get_progress().
Also, remove an unnecessary intermediate 'recovery_cp' variable in
rs_get_progress().
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Arnd Bergmann [Wed, 4 Oct 2017 10:28:18 +0000 (12:28 +0200)]
KVM: add X86_LOCAL_APIC dependency
The rework of the posted interrupt handling broke building without
support for the local APIC:
ERROR: "boot_cpu_physical_apicid" [arch/x86/kvm/kvm-intel.ko] undefined!
That configuration is probably not particularly useful anyway, so
we can avoid the randconfig failures by adding a Kconfig dependency.
Fixes:
8b306e2f3c41 ("KVM: VMX: avoid double list add with VT-d posted interrupts")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Linus Torvalds [Thu, 5 Oct 2017 17:39:29 +0000 (10:39 -0700)]
Merge tag 'sound-4.14-rc4' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes, mostly with stable ones:
- X32 ABI fix for PCM; likely not so many people suffer from it, but
still better to fix
- Two minor kernel warning fixes on USB audio devices spotted by
syzkaller
- Regression fix of echoaudio due to its inconsistent dimension
- Fix for HBR support on Intel DP audio, on some recent chips
- USB-audio quirk for yet another Plantronics devices
- Fix for potential double-fetch in ASIHPI FIFO queue"
* tag 'sound-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usx2y: Suppress kernel warning at page allocation failures
Revert "ALSA: echoaudio: purge contradictions between dimension matrix members and total number of members"
ALSA: usb-audio: Check out-of-bounds access by corrupted buffer descriptor
ALSA: pcm: Fix structure definition for X32 ABI
ALSA: usb-audio: Add sample rate quirk for Plantronics C310/C520-M
ALSA: hda - program ICT bits to support HBR audio
ALSA: asihpi: fix a potential double-fetch bug when copying puhm
ALSA: compress: Remove unused variable
Linus Torvalds [Thu, 5 Oct 2017 17:28:12 +0000 (10:28 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
Pull HID subsystem fixes from Jiri Kosina:
- buffer management size fix for i2c-hid driver, from Adrian Salido
- tool ID regression fixes for Wacom driver from Jason Gerecke
- a few small assorted fixes and a few device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
Revert "HID: multitouch: Support ALPS PTP stick with pid 0x120A"
HID: hidraw: fix power sequence when closing device
HID: wacom: Always increment hdev refcount within wacom_get_hdev_data
HID: wacom: generic: Clear ABS_MISC when tool leaves proximity
HID: wacom: generic: Send MSC_SERIAL and ABS_MISC when leaving prox
HID: i2c-hid: allocate hid buffers for real worst case
HID: rmi: Make sure the HID device is opened on resume
HID: multitouch: Support ALPS PTP stick with pid 0x120A
HID: multitouch: support buttons and trackpoint on Lenovo X1 Tab Gen2
HID: wacom: Correct coordinate system of touchring and pen twist
HID: wacom: Properly report negative values from Intuos Pro 2 Bluetooth
HID: multitouch: Fix system-control buttons not working
HID: add multi-input quirk for IDC6680 touchscreen
HID: wacom: leds: Don't try to control the EKR's read-only LEDs
HID: wacom: bits shifted too much for 9th and 10th buttons
Jens Axboe [Thu, 5 Oct 2017 16:44:04 +0000 (10:44 -0600)]
Merge branch 'nvme-4.14' of git://git.infradead.org/nvme into for-linus
Pull NVMe fixes from Christoph:
"A trivial one-liner from Martin to fix the visible of the uuid attr,
and another one (originally from Abhishek Shah, rewritten by me) to fix
the CMB addresses passed back to the controller in case of a system that
remaps BAR addresses between host and device."
Linus Torvalds [Thu, 5 Oct 2017 15:40:09 +0000 (08:40 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Check iwlwifi 9000 reorder buffer out-of-space condition properly,
from Sara Sharon.
2) Fix RCU splat in qualcomm rmnet driver, from Subash Abhinov
Kasiviswanathan.
3) Fix session and tunnel release races in l2tp, from Guillaume Nault
and Sabrina Dubroca.
4) Fix endian bug in sctp_diag_dump(), from Dan Carpenter.
5) Several mlx5 driver fixes from the Mellanox folks (max flow counters
cap check, invalid memory access in IPoIB support, etc.)
6) tun_get_user() should bail if skb->len is zero, from Alexander
Potapenko.
7) Fix RCU lookups in inetpeer, from Eric Dumazet.
8) Fix locking in packet_do_bund().
9) Handle cb->start() error properly in netlink dump code, from Jason
A. Donenfeld.
10) Handle multicast properly in UDP socket early demux code. From Paolo
Abeni.
11) Several erspan bug fixes in ip_gre, from Xin Long.
12) Fix use-after-free in socket filter code, in order to handle the
fact that listener lock is no longer taken during the three-way TCP
handshake. From Eric Dumazet.
13) Fix infoleak in RTM_GETSTATS, from Nikolay Aleksandrov.
14) Fix tail call generation in x86-64 BPF JIT, from Alexei Starovoitov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
net: 8021q: skip packets if the vlan is down
bpf: fix bpf_tail_call() x64 JIT
net: stmmac: dwmac-rk: Add RK3128 GMAC support
rndis_host: support Novatel Verizon USB730L
net: rtnetlink: fix info leak in RTM_GETSTATS call
socket, bpf: fix possible use after free
mlxsw: spectrum_router: Track RIF of IPIP next hops
mlxsw: spectrum_router: Move VRF refcounting
net: hns3: Fix an error handling path in 'hclge_rss_init_hw()'
net: mvpp2: Fix clock resource by adding an optional bus clock
r8152: add Linksys USB3GIGV1 id
l2tp: fix l2tp_eth module loading
ip_gre: erspan device should keep dst
ip_gre: set tunnel hlen properly in erspan_tunnel_init
ip_gre: check packet length and mtu correctly in erspan_xmit
ip_gre: get key from session_id correctly in erspan_rcv
tipc: use only positive error codes in messages
ppp: fix __percpu annotation
udp: perform source validation for mcast early demux
IPv4: early demux can return an error code
...
Amir Goldstein [Fri, 29 Sep 2017 07:21:21 +0000 (10:21 +0300)]
ovl: fix regression caused by exclusive upper/work dir protection
Enforcing exclusive ownership on upper/work dirs caused a docker
regression: https://github.com/moby/moby/issues/34672.
Euan spotted the regression and pointed to the offending commit.
Vivek has brought the regression to my attention and provided this
reproducer:
Terminal 1:
mount -t overlay -o workdir=work,lowerdir=lower,upperdir=upper none
merged/
Terminal 2:
unshare -m
Terminal 1:
umount merged
mount -t overlay -o workdir=work,lowerdir=lower,upperdir=upper none
merged/
mount: /root/overlay-testing/merged: none already mounted or mount point
busy
To fix the regression, I replaced the error with an alarming warning.
With index feature enabled, mount does fail, but logs a suggestion to
override exclusive dir protection by disabling index.
Note that index=off mount does take the inuse locks, so a concurrent
index=off will issue the warning and a concurrent index=on mount will fail.
Documentation was updated to reflect this change.
Fixes:
2cac0c00a6cd ("ovl: get exclusive ownership on upper/work dirs")
Cc: <stable@vger.kernel.org> # v4.13
Reported-by: Euan Kemp <euank@euank.com>
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Amir Goldstein [Mon, 25 Sep 2017 13:39:55 +0000 (16:39 +0300)]
ovl: fix missing unlock_rename() in ovl_do_copy_up()
Use the ovl_lock_rename_workdir() helper which requires
unlock_rename() only on lock success.
Fixes: ("
fd210b7d67ee ovl: move copy up lock out")
Cc: <stable@vger.kernel.org> # v4.13
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Amir Goldstein [Sun, 24 Sep 2017 19:19:10 +0000 (22:19 +0300)]
ovl: fix dentry leak in ovl_indexdir_cleanup()
index dentry was not released when breaking out of the loop
due to index verification error.
Fixes:
415543d5c64f ("ovl: cleanup bad and stale index entries on mount")
Cc: <stable@vger.kernel.org> # v4.13
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Amir Goldstein [Sun, 24 Sep 2017 14:36:26 +0000 (17:36 +0300)]
ovl: fix dput() of ERR_PTR in ovl_cleanup_index()
Fixes:
caf70cb2ba5d ("ovl: cleanup orphan index entries")
Cc: <stable@vger.kernel.org> # v4.13
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Amir Goldstein [Sun, 24 Sep 2017 10:01:35 +0000 (13:01 +0300)]
ovl: fix error value printed in ovl_lookup_index()
Fixes:
359f392ca53e ("ovl: lookup index entry for copy up origin")
Cc: <stable@vger.kernel.org> # v4.13
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Amir Goldstein [Mon, 18 Sep 2017 19:53:43 +0000 (22:53 +0300)]
ovl: fix may_write_real() for overlayfs directories
Overlayfs directory file_inode() is the overlay inode whether the real
inode is upper or lower.
This fixes a regression in xfstest generic/158.
Fixes:
7c6893e3c9ab ("ovl: don't allow writing ioctl on lower layer")
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Josh Poimboeuf [Wed, 4 Oct 2017 15:39:05 +0000 (10:39 -0500)]
x86/kvm: Move kvm_fastop_exception to .fixup section
When compiling the kernel with the '-frecord-gcc-switches' flag, objtool
complains:
arch/x86/kvm/emulate.o: warning: objtool: .GCC.command.line+0x0: special: can't find new instruction
And also the kernel fails to link.
The problem is that the 'kvm_fastop_exception' code gets placed into the
throwaway '.GCC.command.line' section instead of '.text'.
Exception fixup code is conventionally placed in the '.fixup' section,
so put it there where it belongs.
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Colin Ian King [Mon, 18 Sep 2017 08:15:39 +0000 (09:15 +0100)]
i2c: i2c-stm32f7: make structure stm32f7_setup static const
The structure stm32f7_setup is local to the source and does not need
to be in global scope, make it static const.
Cleans up sparse warning:
symbol 'stm32f7_setup' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Thomas Meyer [Thu, 21 Sep 2017 06:24:27 +0000 (08:24 +0200)]
i2c: ensure termination of *_device_id tables
Make sure (of/i2c/platform)_device_id tables are NULL terminated.
Found by coccinelle spatch "misc/of_table.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jarkko Nikula [Thu, 21 Sep 2017 13:23:16 +0000 (16:23 +0300)]
i2c: i801: Add support for Intel Cedar Fork
Add PCI ID for Intel Cedar Fork PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pierre-Yves MORDRET [Thu, 21 Sep 2017 13:30:09 +0000 (15:30 +0200)]
i2c: stm32f7: fix setup structure
I2C drive setup structure is not properly allocated.
Make it static instead of pointer to store driver data.
Fixes:
aeb068c5721485 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Vishakha Narvekar [Tue, 3 Oct 2017 20:13:29 +0000 (16:13 -0400)]
net: 8021q: skip packets if the vlan is down
If the vlan is down, free the packet instead of proceeding with other
processing, or counting it as received. If vlan interfaces are used
as slaves for bonding, with arp monitoring for connectivity, if the rx
counter is seen to be incrementing, then the bond device will not
observe that the interface is down.
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: Vishakha Narvekar <Vishakha.Narvekar@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 5 Oct 2017 00:16:05 +0000 (17:16 -0700)]
Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Our first batch of fixes this release cycle, unfortunately a bit
noisier than usual. Two major groups stand out:
- Some pinctril dts/dtsi changes for stm32 due to a new driver being
merged during the merge window, and this aligns the DT contents
between the old format and the new. This could arguably be moved to
the next merge window but it also seemed relatively harmless to
include now.
- Amlogic/meson had driver changes merged that required devicetree
changes to avoid functional/performance regressions. I've already
asked them to be more careful about this going forward, and making
sure drivers are compatible with older DTs when they make these
kind of changes. The platform is actively being upstreamed so
there's a few things in flight, we've seen this happen before and
sometimes it's hard to catch in time.
Besides that there is the usual mix of minor fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: dts: stm32: use right pinctrl compatible for stm32f469
ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board
ARM: defconfig: update Gemini defconfig
ARM: defconfig: FRAMEBUFFER_CONSOLE can no longer be =m
arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399
reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
ARM: dts: da850-evm: add serial and ethernet aliases
ARM: dts: am43xx-epos-evm: Remove extra CPSW EMAC entry
ARM: dts: am33xx: Add spi alias to match SOC schematics
ARM: OMAP2+: hsmmc: fix logic to call either omap_hsmmc_init or omap_hsmmc_late_init but not both
ARM: dts: dra7: Set a default parent to mcasp3_ahclkx_mux
ARM: OMAP2+: dra7xx: Set OPT_CLKS_IN_RESET flag for gpio1
ARM: dts: nokia n900: drop unneeded/undocumented parts of the dts
arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399
arm64: dt marvell: Fix AP806 system controller size
MAINTAINERS: add Macchiatobin maintainers entry
ARC: reset: remove the misleading v1 suffix all over
ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
ARC: reset: Only build on archs that have IOMEM
ARM: at91: Replace uses of virt_to_phys with __pa_symbol
...
James Hogan [Wed, 4 Oct 2017 22:10:59 +0000 (23:10 +0100)]
Update James Hogan's email address
Update my imgtec.com and personal email address to my kernel.org one in
a few places as MIPS will soon no longer be part of Imagination
Technologies, and add mappings in .mailcap so get_maintainer.pl reports
the right address.
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Imre Deak [Tue, 3 Oct 2017 09:51:59 +0000 (12:51 +0300)]
drm/i915/glk: Fix DMC/DC state idleness calculation
According to BSpec GLK like BXT needs to ignore the idle state of cores
before starting the DMC firmware's DC state handler.
Fixes:
dbb28b5c3d3c ("drm/i915/DMC/GLK: Load DMC on GLK")
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003095159.711-2-imre.deak@intel.com
(cherry picked from commit
b7208a3f3e52791571df064fb96025ad48edd1bf)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Imre Deak [Tue, 3 Oct 2017 09:51:58 +0000 (12:51 +0300)]
drm/i915/cnl: Reprogram DMC firmware after S3/S4 resume
The DMC firmware program memory is lost after S3/S4 system suspend, so
we need to reprogram it during resume.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103070
Fixes:
cebfcead63de ("drm/i915/DMC/CNL: Load DMC on CNL")
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003095159.711-1-imre.deak@intel.com
(cherry picked from commit
57522c4c87de20d8f7ad4e142a3a4334066d55ff)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Rafael J. Wysocki [Tue, 26 Sep 2017 20:45:44 +0000 (22:45 +0200)]
PM: ARM: locomo: Drop suspend and resume bus type callbacks
None of the locomo drivers in the tree implements the suspend and
resume callbacks from struct locomo_driver, so drop them and drop
the corresponding callbacks from locomo_bus_type.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Mustafa Ismail [Tue, 3 Oct 2017 16:11:50 +0000 (11:11 -0500)]
i40iw: Fix port number for query QP
Port number 0 is an invalid port number. Set it to 1
as there is one port per i40iw device.
Fixes:
d37498417947 ("i40iw: add files for iwarp interface")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Mustafa Ismail [Tue, 3 Oct 2017 16:11:49 +0000 (11:11 -0500)]
i40iw: Add missing memory barriers
Remove duplicate set_64bit_val call to offset 24.
Replace some instances of set_64bit_val with
i40iw_insert_wqe_hdr as valid bit needs a write
barrier and should be the last write operation for the WQE.
Fixes:
786c6adb3a94 ("i40iw: add puda code")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Amrani, Ram [Tue, 3 Oct 2017 11:47:27 +0000 (14:47 +0300)]
RDMA/qedr: Parse vlan priority as sl
Parse the vlan priority from the vlan tag and configure it to the
WC's sl field.
Fixes:
abd49676c707 ("qed: Add RoCE ll2 & GSI support")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Amrani, Ram [Tue, 3 Oct 2017 11:47:26 +0000 (14:47 +0300)]
RDMA/qedr: Parse VLAN ID correctly and ignore the value of zero
Rename vlan_id field name to vlan as it contains more than the vlan_id.
Mask out non vlan id fields from vlan tag of the QED LL2 RX GSI
vlan output. As it is expected to be vlan id only.
Ignore vlan_id with value of zero.
Fixes:
abd49676c707 ("qed: Add RoCE ll2 & GSI support")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Parav Pandit [Sun, 1 Oct 2017 06:54:35 +0000 (09:54 +0300)]
IB/mlx5: Fix label order in error path handling
When UAR get_page fails, it needs to continue to cleanup debugfs for
congestion control parameters. Labels for error path were incorrectly
ordered.
This patch fixes to do correct cleanup on debugfs init failure and uar
get page failure.
Fixes:
4a2da0b8c078 ("IB/mlx5: Add debug control parameters for congestion control")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Olof Johansson [Wed, 4 Oct 2017 17:31:00 +0000 (10:31 -0700)]
Merge tag 'stm32-dt-fixes-for-v4.14' of git://git./linux/kernel/git/atorgue/stm32 into fixes
STM32 fixes for v4.14:
---------------------
-Fix STMPE1600 bindings for stm32429i-eval board
-Use right compatible for stm32f469 pinctrl. It implies to use
pinctrl dedicated files for F4 SoCs.
* tag 'stm32-dt-fixes-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: use right pinctrl compatible for stm32f469
ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 4 Oct 2017 17:30:39 +0000 (10:30 -0700)]
Merge tag 'amlogic-dt64-3' of git://git./linux/kernel/git/khilman/linux-amlogic into fixes
Amlogic 64-bit DT updates for v4.14 (round 3)
- updates for new MMC driver features/fixes
- support high-speed modes
* tag 'amlogic-dt64-3' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxbb: nanopi-k2: enable sdr104 mode
ARM64: dts: meson-gxbb: nanopi-k2: enable sdcard UHS modes
ARM64: dts: meson-gxbb: p20x: enable sdcard UHS modes
ARM64: dts: meson-gxl: libretech-cc: enable high speed modes
ARM64: dts: meson-gxl: libretech-cc: add card regulator settle times
ARM64: dts: meson-gxbb: nanopi-k2: add card regulator settle times
ARM64: dts: meson: add mmc clk gate pins
ARM64: dts: meson: remove cap-sd-highspeed from emmc nodes
ARM64: dts: meson-gx: Use correct mmc clock source 0
Signed-off-by: Olof Johansson <olof@lixom.net>
Mark Rutland [Tue, 3 Oct 2017 17:25:46 +0000 (18:25 +0100)]
arm64: Use larger stacks when KASAN is selected
AddressSanitizer instrumentation can significantly bloat the stack, and
with GCC 7 this can result in stack overflows at boot time in some
configurations.
We can avoid this by doubling our stack size when KASAN is in use, as is
already done on x86 (and has been since KASAN was introduced).
Regardless of other patches to decrease KASAN's stack utilization,
kernels built with KASAN will always require more stack space than those
built without, and we should take this into account.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Lorenzo Pieralisi [Mon, 2 Oct 2017 17:28:44 +0000 (18:28 +0100)]
ACPI/IORT: Fix PCI ACS enablement
commit
f6810c15cf97 ("iommu/arm-smmu: Clean up early-probing
workarounds") removed kernel code that was allowing to initialize
and probe the SMMU devices early (ie earlier than PCI devices, through
linker script callback entries) in the boot process because it was not
needed any longer in that the SMMU devices/drivers now support deferred
probing.
Since the SMMUs probe routines are also in charge of requesting global
PCI ACS kernel enablement, commit
f6810c15cf97 ("iommu/arm-smmu: Clean
up early-probing workarounds") also postponed PCI ACS enablement to
SMMUs devices probe time, which is too late given that PCI devices needs
to detect if PCI ACS is enabled to init the respective capability
through the following call path:
pci_device_add()
-> pci_init_capabilities()
-> pci_enable_acs()
Add code in the ACPI IORT SMMU platform devices initialization path
(that is called before ACPI PCI enumeration) to detect if there
exists firmware mappings to map root complexes ids to SMMU ids
and if so enable ACS for the system.
Fixes:
f6810c15cf97 ("iommu/arm-smmu: Clean up early-probing workarounds")
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Linus Torvalds [Wed, 4 Oct 2017 16:30:50 +0000 (09:30 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"A lot of stuff, sorry about that. A week on a beach, then a bunch of
time catching up then more time letting it bake in -next. Shan't do
that again!"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (51 commits)
include/linux/fs.h: fix comment about struct address_space
checkpatch: fix ignoring cover-letter logic
m32r: fix build failure
lib/ratelimit.c: use deferred printk() version
kernel/params.c: improve STANDARD_PARAM_DEF readability
kernel/params.c: fix an overflow in param_attr_show
kernel/params.c: fix the maximum length in param_get_string
mm/memory_hotplug: define find_{smallest|biggest}_section_pfn as unsigned long
mm/memory_hotplug: change pfn_to_section_nr/section_nr_to_pfn macro to inline function
kernel/kcmp.c: drop branch leftover typo
memremap: add scheduling point to devm_memremap_pages
mm, page_alloc: add scheduling point to memmap_init_zone
mm, memory_hotplug: add scheduling point to __add_pages
lib/idr.c: fix comment for idr_replace()
mm: memcontrol: use vmalloc fallback for large kmem memcg arrays
kernel/sysctl.c: remove duplicate UINT_MAX check on do_proc_douintvec_conv()
include/linux/bitfield.h: remove 32bit from FIELD_GET comment block
lib/lz4: make arrays static const, reduces object code size
exec: binfmt_misc: kill the onstack iname[BINPRM_BUF_SIZE] array
exec: binfmt_misc: fix race between load_misc_binary() and kill_node()
...
Boqun Feng [Tue, 3 Oct 2017 13:36:51 +0000 (21:36 +0800)]
kvm/x86: Avoid async PF preempting the kernel incorrectly
Currently, in PREEMPT_COUNT=n kernel, kvm_async_pf_task_wait() could call
schedule() to reschedule in some cases. This could result in
accidentally ending the current RCU read-side critical section early,
causing random memory corruption in the guest, or otherwise preempting
the currently running task inside between preempt_disable and
preempt_enable.
The difficulty to handle this well is because we don't know whether an
async PF delivered in a preemptible section or RCU read-side critical section
for PREEMPT_COUNT=n, since preempt_disable()/enable() and rcu_read_lock/unlock()
are both no-ops in that case.
To cure this, we treat any async PF interrupting a kernel context as one
that cannot be preempted, preventing kvm_async_pf_task_wait() from choosing
the schedule() path in that case.
To do so, a second parameter for kvm_async_pf_task_wait() is introduced,
so that we know whether it's called from a context interrupting the
kernel, and the parameter is set properly in all the callsites.
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Linus Torvalds [Wed, 4 Oct 2017 16:21:58 +0000 (09:21 -0700)]
Merge branch 'fixes-v4.14-rc4' of git://git./linux/kernel/git/jmorris/linux-security
Pull smack fix from James Morris:
"It fixes a bug in xattr_getsecurity() where security_release_secctx()
was being called instead of kfree(), which leads to a memory leak in
the capabilities code. smack_inode_getsecurity is also fixed to behave
correctly when called from there"
* 'fixes-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
lsm: fix smack_inode_removexattr and xattr_getsecurity memleak
Marek Szyprowski [Tue, 19 Sep 2017 10:01:08 +0000 (12:01 +0200)]
clk: samsung: exynos4: Enable VPLL and EPLL clocks for suspend/resume cycle
Commit
6edfa11cb396 ("clk: samsung: Add enable/disable operation for
PLL36XX clocks") added enable/disable operations to PLL clocks. Prior that
VPLL and EPPL clocks were always enabled because the enable bit was never
touched. Those clocks have to be enabled during suspend/resume cycle,
because otherwise board fails to enter sleep mode. This patch enables them
unconditionally before entering system suspend state. System restore
function will set them to the previous state saved in the register cache
done before that unconditional enable.
Fixes:
6edfa11cb396 ("clk: samsung: Add enable/disable operation for PLL36XX clocks")
CC: stable@vger.kernel.org # v4.13
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Linus Torvalds [Wed, 4 Oct 2017 15:34:01 +0000 (08:34 -0700)]
Merge tag 'trace-v4.14-rc1-3' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixlets from Steven Rostedt:
"Two updates:
- A memory fix with left over code from spliting out ftrace_ops and
function graph tracer, where the function graph tracer could reset
the trampoline pointer, leaving the old trampoline not to be freed
(memory leak).
- The update to Paul's patch that added the unnecessary READ_ONCE().
This removes the unnecessary READ_ONCE() instead of having to
rebase the branch to update the patch that added it"
* tag 'trace-v4.14-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
rcu: Remove extraneous READ_ONCE()s from rcu_irq_{enter,exit}()
ftrace: Fix kmemleak in unregister_ftrace_graph
Milan Broz [Wed, 13 Sep 2017 13:45:56 +0000 (15:45 +0200)]
dm crypt: reject sector_size feature if device length is not aligned to it
If a crypt mapping uses optional sector_size feature, additional
restrictions to mapped device segment size must be applied in
constructor, otherwise the device activation will fail later.
Fixes:
8f0009a225 ("dm crypt: optionally support larger encryption sector size")
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Tsutomu Itoh [Wed, 4 Oct 2017 02:05:17 +0000 (11:05 +0900)]
Btrfs: fix overlap of fs_info::flags values
Because the values of BTRFS_FS_EXCL_OP and BTRFS_FS_QUOTA_OVERRIDE overlap,
we should change the value.
First, BTRFS_FS_EXCL_OP was set to 14.
commit
171938e52807 ("btrfs: track exclusive filesystem operation in flags")
Next, the value of BTRFS_FS_QUOTA_OVERRIDE was set to 14.
commit
f29efe292198 ("btrfs: add quota override flag to enable quota override for CAP_SYS_RESOURCE")
As a result, the value 14 overlapped, by accident.
This problem is solved by defining the value of BTRFS_FS_EXCL_OP as 16,
the flags are internal.
Fixes:
f29efe292198 ("btrfs: add quota override flag to enable quota override for CAP_SYS_RESOURCE")
CC: stable@vger.kernel.org # 4.13+
Signed-off-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ minimize the change, update only BTRFS_FS_EXCL_OP ]
Signed-off-by: David Sterba <dsterba@suse.com>
Benjamin Block [Tue, 3 Oct 2017 10:48:37 +0000 (12:48 +0200)]
bsg-lib: fix use-after-free under memory-pressure
When under memory-pressure it is possible that the mempool which backs
the 'struct request_queue' will make use of up to BLKDEV_MIN_RQ count
emergency buffers - in case it can't get a regular allocation. These
buffers are preallocated and once they are also used, they are
re-supplied with old finished requests from the same request_queue (see
mempool_free()).
The bug is, when re-supplying the emergency pool, the old requests are
not again ran through the callback mempool_t->alloc(), and thus also not
through the callback bsg_init_rq(). Thus we skip initialization, and
while the sense-buffer still should be good, scsi_request->cmd might
have become to be an invalid pointer in the meantime. When the request
is initialized in bsg.c, and the user's CDB is larger than BLK_MAX_CDB,
bsg will replace it with a custom allocated buffer, which is freed when
the user's command is finished, thus it dangles afterwards. When next a
command is sent by the user that has a smaller/similar CDB as
BLK_MAX_CDB, bsg will assume that scsi_request->cmd is backed by
scsi_request->__cmd, will not make a custom allocation, and write into
undefined memory.
Fix this by splitting bsg_init_rq() into two functions:
- bsg_init_rq() is changed to only do the allocation of the
sense-buffer, which is used to back the bsg job's reply buffer. This
pointer should never change during the lifetime of a scsi_request, so
it doesn't need re-initialization.
- bsg_initialize_rq() is a new function that makes use of
'struct request_queue's initialize_rq_fn callback (which was
introduced in v4.12). This is always called before the request is
given out via blk_get_request(). This function does the remaining
initialization that was previously done in bsg_init_rq(), and will
also do it when the request is taken from the emergency-pool of the
backing mempool.
Fixes:
50b4d485528d ("bsg-lib: fix kernel panic resulting from missing allocation of reply-buffer")
Cc: <stable@vger.kernel.org> # 4.11+
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Goffredo Baroncelli [Tue, 3 Oct 2017 17:31:10 +0000 (19:31 +0200)]
btrfs: avoid overflow when sector_t is 32 bit
Jean-Denis Girard noticed commit
c821e7f3 "pass bytes to
btrfs_bio_alloc" (https://patchwork.kernel.org/patch/
9763081/)
introduces a regression on 32 bit machines.
When CONFIG_LBDAF is _not_ defined (CONFIG_LBDAF == Support for large
(2TB+) block devices and files) sector_t is 32 bit on 32bit machines.
In the function submit_extent_page, 'sector' (which is sector_t type) is
multiplied by 512 to convert it from sectors to bytes, leading to an
overflow when the disk is bigger than 4GB (!).
I added a cast to u64 to avoid overflow.
Fixes:
c821e7f3 ("btrfs: pass bytes to btrfs_bio_alloc")
CC: stable@vger.kernel.org # 4.13+
Signed-off-by: Goffredo Baroncelli <kreijack@inwind.it>
Tested-by: Jean-Denis Girard <jd.girard@sysnux.pf>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Alexandre Torgue [Wed, 4 Oct 2017 13:34:48 +0000 (15:34 +0200)]
ARM: dts: stm32: use right pinctrl compatible for stm32f469
Currently, same stm32f429-pinctrl driver is used for stm32f429 and
stm32f469. As pin map is different between those 2 MCUs,
a stm32f469-pinctrl driver has been recently added.
This patch
-allows to use stm32f469-pinctrl driver for stm32f469 boards
-reworks stm32 devicetree files to fit with stm32f429 / stm32f469
In the same time it fixes an issue when only MACH_STM32F469 flag is
selected in menuconfig.
Fixes:
d28bcd53fa90 ("ARM: stm32: Introduce MACH_STM32F469 flag")
Reported-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Guenter Roeck [Sun, 24 Sep 2017 17:30:43 +0000 (10:30 -0700)]
powerpc/mm: Call flush_tlb_kernel_range with interrupts enabled
flush_tlb_kernel_range() may call smp_call_function_many() which expects
interrupts to be enabled. This results in a traceback.
WARNING: CPU: 0 PID: 1 at kernel/smp.c:416 smp_call_function_many+0xcc/0x2fc
CPU: 0 PID: 1 Comm: swapper/0 Not tainted
4.14.0-rc1-00009-g0666f56 #1
task:
cf830000 task.stack:
cf82e000
NIP:
c00a93c8 LR:
c00a9634 CTR:
00000001
REGS:
cf82fde0 TRAP: 0700 Not tainted (
4.14.0-rc1-00009-g0666f56)
MSR:
00021000 <CE,ME> CR:
24000082 XER:
00000000
GPR00:
c00a9634 cf82fe90 cf830000 c050ad3c c0015a54 00000000 00000001 00000001
GPR08:
00000001 00000000 00000000 cf82e000 24000084 00000000 c0003150 00000000
GPR16:
00000000 00000000 00000000 00000000 00000000 00000001 00000000 c0510000
GPR24:
00000000 c0015a54 00000000 c050ad3c c051823c c050ad3c 00000025 00000000
NIP [
c00a93c8] smp_call_function_many+0xcc/0x2fc
LR [
c00a9634] smp_call_function+0x3c/0x50
Call Trace:
[
cf82fe90] [
00000010] 0x10 (unreliable)
[
cf82fed0] [
c00a9634] smp_call_function+0x3c/0x50
[
cf82fee0] [
c0015d2c] flush_tlb_kernel_range+0x20/0x38
[
cf82fef0] [
c001524c] mark_initmem_nx+0x154/0x16c
[
cf82ff20] [
c001484c] free_initmem+0x20/0x4c
[
cf82ff30] [
c000316c] kernel_init+0x1c/0x108
[
cf82ff40] [
c000f3a8] ret_from_kernel_thread+0x5c/0x64
Instruction dump:
7c0803a6 7d808120 38210040 4e800020 3d20c052 812981a0 2f890000 40beffac
3d20c051 8929ac64 2f890000 40beff9c <
0fe00000>
4bffff94 7fc3f378 7f64db78
Fixes:
3184cc4b6f6a ("powerpc/mm: Fix kernel RAM protection after freeing ...")
Fixes:
e611939fc8ec ("powerpc/mm: Ensure change_page_attr() doesn't ...")
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Cédric Le Goater [Wed, 4 Oct 2017 09:15:05 +0000 (11:15 +0200)]
powerpc/xive: Clear XIVE internal structures when a CPU is removed
Commit
eac1e731b59e ("powerpc/xive: guest exploitation of the XIVE
interrupt controller") introduced support for the XIVE exploitation
mode of the P9 interrupt controller on the pseries platform.
At that time, support for CPU removal was not complete on PowerVM and
CPU hot unplug remained untested. It appears that some cleanups of the
XIVE internal structures are required before releasing the CPU,
without which the kernel crashes in a RTAS call doing the CPU
isolation.
These changes fix the crash by deconfiguring the IPI interrupt source
and clearing the event queues of the CPU when it is removed.
Fixes:
eac1e731b59e ("powerpc/xive: guest exploitation of the XIVE interrupt controller")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Cédric Le Goater [Wed, 4 Oct 2017 09:15:04 +0000 (11:15 +0200)]
powerpc/xive: Fix IPI reset
When resetting an IPI, hw_ipi should also be set to zero.
Fixes:
eac1e731b59e ("powerpc/xive: guest exploitation of the XIVE interrupt controller")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christoph Hellwig [Sun, 1 Oct 2017 07:37:35 +0000 (09:37 +0200)]
nvme-pci: Use PCI bus address for data/queues in CMB
Currently, NVMe PCI host driver is programming CMB dma address as
I/O SQs addresses. This results in failures on systems where 1:1
outbound mapping is not used (example Broadcom iProc SOCs) because
CMB BAR will be progammed with PCI bus address but NVMe PCI EP will
try to access CMB using dma address.
To have CMB working on systems without 1:1 outbound mapping, we
program PCI bus address for I/O SQs instead of dma address. This
approach will work on systems with/without 1:1 outbound mapping.
Based on a report and previous patch from Abhishek Shah.
Fixes:
8ffaadf7 ("NVMe: Use CMB for the IO SQes if available")
Cc: stable@vger.kernel.org
Reported-by: Abhishek Shah <abhishek.shah@broadcom.com>
Tested-by: Abhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Alexandre Torgue [Wed, 4 Oct 2017 09:42:00 +0000 (11:42 +0200)]
ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board
To declare gpio interrupt line for STMPE1600, 2 possibilities are offered:
-use gpio binding (and then the gpiolib interface inside driver)
-use interrupt binding as each gpio-controller are also interrupt controller
on stm32f429.
In STMPE 1600 node both (gpio and interrupt) bindings are defined.
This patch fixes this issue and use only interrupt binding.
Fixes:
c04b2e72af8d ("ARM: dts: stm32: Enable STMPE1600 gpio expander of STM32F429-EVAL board")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Thomas Gleixner [Mon, 2 Oct 2017 18:59:09 +0000 (20:59 +0200)]
watchdog/core: Put softlockup_threads_initialized under ifdef guard
The variable is unused when the softlockup detector is disabled in Kconfig.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Wed, 4 Oct 2017 08:03:04 +0000 (10:03 +0200)]
watchdog/core: Rename some softlockup_* functions
The function names made sense up to the point where the watchdog
(re)configuration was unified to use softlockup_reconfigure_threads() for
all configuration purposes. But that includes scenarios which solely
configure the nmi watchdog.
Rename softlockup_reconfigure_threads() and softlockup_init_threads() so
the function names match the functionality.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Don Zickus <dzickus@redhat.com>
Thomas Gleixner [Tue, 3 Oct 2017 14:39:02 +0000 (16:39 +0200)]
powerpc/watchdog: Make use of watchdog_nmi_probe()
The rework of the core hotplug code triggers the WARN_ON in start_wd_cpu()
on powerpc because it is called multiple times for the boot CPU.
The first call is via:
start_wd_on_cpu+0x80/0x2f0
watchdog_nmi_reconfigure+0x124/0x170
softlockup_reconfigure_threads+0x110/0x130
lockup_detector_init+0xbc/0xe0
kernel_init_freeable+0x18c/0x37c
kernel_init+0x2c/0x160
ret_from_kernel_thread+0x5c/0xbc
And then again via the CPU hotplug registration:
start_wd_on_cpu+0x80/0x2f0
cpuhp_invoke_callback+0x194/0x620
cpuhp_thread_fun+0x7c/0x1b0
smpboot_thread_fn+0x290/0x2a0
kthread+0x168/0x1b0
ret_from_kernel_thread+0x5c/0xbc
This can be avoided by setting up the cpu hotplug state with nocalls and
move the initialization to the watchdog_nmi_probe() function. That
initializes the hotplug callbacks without invoking the callback and the
following core initialization function then configures the watchdog for the
online CPUs (in this case CPU0) via softlockup_reconfigure_threads().
Reported-and-tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Thomas Gleixner [Tue, 3 Oct 2017 14:37:53 +0000 (16:37 +0200)]
watchdog/core, powerpc: Lock cpus across reconfiguration
Instead of dropping the cpu hotplug lock after stopping NMI watchdog and
threads and reaquiring for restart, the code and the protection rules
become more obvious when holding cpu hotplug lock across the full
reconfiguration.
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1710022105570.2114@nanos