OSDN Git Service
Linus Torvalds [Fri, 26 Sep 2014 18:04:31 +0000 (11:04 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"A small fixup to i8042 adding Asus X450LCP to the nomux list"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - fix Asus X450LCP touchpad detection
Linus Torvalds [Fri, 26 Sep 2014 15:38:09 +0000 (08:38 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"A CONFIG_STACK_GROWSUP=y fix, and a hotplug llc CPU mask fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix unreleased llc_shared_mask bit during CPU hotplug
sched: Fix end_of_stack() and location of stack canary for architectures using CONFIG_STACK_GROWSUP
Linus Torvalds [Fri, 26 Sep 2014 15:11:43 +0000 (08:11 -0700)]
Merge branch 'akpm' (fixes from Andrew Morton)
Merge fixes from Andrew Morton:
"9 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: softdirty: keep bit when zapping file pte
fs/cachefiles: add missing \n to kerror conversions
genalloc: fix device node resource counter
drivers/rtc/rtc-efi.c: add missing module alias
mm, slab: initialize object alignment on cache creation
mm: softdirty: addresses before VMAs in PTE holes aren't softdirty
ocfs2/dlm: do not get resource spinlock if lockres is new
nilfs2: fix data loss with mmap()
ocfs2: free vol_label in ocfs2_delete_osb()
Peter Feiner [Thu, 25 Sep 2014 23:05:29 +0000 (16:05 -0700)]
mm: softdirty: keep bit when zapping file pte
This fixes the same bug as
b43790eedd31 ("mm: softdirty: don't forget to
save file map softdiry bit on unmap") and
9aed8614af5a ("mm/memory.c:
don't forget to set softdirty on file mapped fault") where the return
value of pte_*mksoft_dirty was being ignored.
To be sure that no other pte/pmd "mk" function return values were being
ignored, I annotated the functions in arch/x86/include/asm/pgtable.h
with __must_check and rebuilt.
The userspace effect of this bug is that the softdirty mark might be
lost if a file mapped pte get zapped.
Signed-off-by: Peter Feiner <pfeiner@google.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Jamie Liu <jamieliu@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fabian Frederick [Thu, 25 Sep 2014 23:05:27 +0000 (16:05 -0700)]
fs/cachefiles: add missing \n to kerror conversions
Commit
0227d6abb378 ("fs/cachefiles: replace kerror by pr_err") didn't
include newline featuring in original kerror definition
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Reported-by: David Howells <dhowells@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: <stable@vger.kernel.org> [3.16.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vladimir Zapolskiy [Thu, 25 Sep 2014 23:05:25 +0000 (16:05 -0700)]
genalloc: fix device node resource counter
Decrement the np_pool device_node refcount, which was incremented on
the preceding of_parse_phandle() call.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pali Rohár [Thu, 25 Sep 2014 23:05:22 +0000 (16:05 -0700)]
drivers/rtc/rtc-efi.c: add missing module alias
Without proper alias kernel module is not loaded for rtc-efi driver.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: dann frazier <dannf@dannf.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Thu, 25 Sep 2014 23:05:20 +0000 (16:05 -0700)]
mm, slab: initialize object alignment on cache creation
Since commit
4590685546a3 ("mm/sl[aou]b: Common alignment code"), the
"ralign" automatic variable in __kmem_cache_create() may be used as
uninitialized.
The proper alignment defaults to BYTES_PER_WORD and can be overridden by
SLAB_RED_ZONE or the alignment specified by the caller.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=85031
Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Andrei Elovikov <a.elovikov@gmail.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Feiner [Thu, 25 Sep 2014 23:05:18 +0000 (16:05 -0700)]
mm: softdirty: addresses before VMAs in PTE holes aren't softdirty
In PTE holes that contain VM_SOFTDIRTY VMAs, unmapped addresses before
VM_SOFTDIRTY VMAs are reported as softdirty by /proc/pid/pagemap. This
bug was introduced in commit
68b5a6524856 ("mm: softdirty: respect
VM_SOFTDIRTY in PTE holes"). That commit made /proc/pid/pagemap look at
VM_SOFTDIRTY in PTE holes but neglected to observe the start of VMAs
returned by find_vma.
Tested:
Wrote a selftest that creates a PMD-sized VMA then unmaps the first
page and asserts that the page is not softdirty. I'm going to send the
pagemap selftest in a later commit.
Signed-off-by: Peter Feiner <pfeiner@google.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Jamie Liu <jamieliu@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Thu, 25 Sep 2014 23:05:16 +0000 (16:05 -0700)]
ocfs2/dlm: do not get resource spinlock if lockres is new
There is a deadlock case which reported by Guozhonghua:
https://oss.oracle.com/pipermail/ocfs2-devel/2014-September/010079.html
This case is caused by &res->spinlock and &dlm->master_lock
misordering in different threads.
It was introduced by commit
8d400b81cc83 ("ocfs2/dlm: Clean up refmap
helpers"). Since lockres is new, it doesn't not require the
&res->spinlock. So remove it.
Fixes:
8d400b81cc83 ("ocfs2/dlm: Clean up refmap helpers")
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: joyce.xue <xuejiufei@huawei.com>
Reported-by: Guozhonghua <guozhonghua@h3c.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andreas Rohner [Thu, 25 Sep 2014 23:05:14 +0000 (16:05 -0700)]
nilfs2: fix data loss with mmap()
This bug leads to reproducible silent data loss, despite the use of
msync(), sync() and a clean unmount of the file system. It is easily
reproducible with the following script:
----------------[BEGIN SCRIPT]--------------------
mkfs.nilfs2 -f /dev/sdb
mount /dev/sdb /mnt
dd if=/dev/zero bs=1M count=30 of=/mnt/testfile
umount /mnt
mount /dev/sdb /mnt
CHECKSUM_BEFORE="$(md5sum /mnt/testfile)"
/root/mmaptest/mmaptest /mnt/testfile 30 10 5
sync
CHECKSUM_AFTER="$(md5sum /mnt/testfile)"
umount /mnt
mount /dev/sdb /mnt
CHECKSUM_AFTER_REMOUNT="$(md5sum /mnt/testfile)"
umount /mnt
echo "BEFORE MMAP:\t$CHECKSUM_BEFORE"
echo "AFTER MMAP:\t$CHECKSUM_AFTER"
echo "AFTER REMOUNT:\t$CHECKSUM_AFTER_REMOUNT"
----------------[END SCRIPT]--------------------
The mmaptest tool looks something like this (very simplified, with
error checking removed):
----------------[BEGIN mmaptest]--------------------
data = mmap(NULL, file_size - file_offset, PROT_READ | PROT_WRITE,
MAP_SHARED, fd, file_offset);
for (i = 0; i < write_count; ++i) {
memcpy(data + i * 4096, buf, sizeof(buf));
msync(data, file_size - file_offset, MS_SYNC))
}
----------------[END mmaptest]--------------------
The output of the script looks something like this:
BEFORE MMAP:
281ed1d5ae50e8419f9b978aab16de83 /mnt/testfile
AFTER MMAP:
6604a1c31f10780331a6850371b3a313 /mnt/testfile
AFTER REMOUNT:
281ed1d5ae50e8419f9b978aab16de83 /mnt/testfile
So it is clear, that the changes done using mmap() do not survive a
remount. This can be reproduced a 100% of the time. The problem was
introduced in commit
136e8770cd5d ("nilfs2: fix issue of
nilfs_set_page_dirty() for page at EOF boundary").
If the page was read with mpage_readpage() or mpage_readpages() for
example, then it has no buffers attached to it. In that case
page_has_buffers(page) in nilfs_set_page_dirty() will be false.
Therefore nilfs_set_file_dirty() is never called and the pages are never
collected and never written to disk.
This patch fixes the problem by also calling nilfs_set_file_dirty() if the
page has no buffers attached to it.
[akpm@linux-foundation.org: s/PAGE_SHIFT/PAGE_CACHE_SHIFT/]
Signed-off-by: Andreas Rohner <andreas.rohner@gmx.net>
Tested-by: Andreas Rohner <andreas.rohner@gmx.net>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Thu, 25 Sep 2014 23:05:11 +0000 (16:05 -0700)]
ocfs2: free vol_label in ocfs2_delete_osb()
osb->vol_label is malloced in ocfs2_initialize_super but not freed if
error occurs or during umount, thus causing a memory leak.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: joyce.xue <xuejiufei@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 25 Sep 2014 22:25:52 +0000 (15:25 -0700)]
Merge tag 'pm+acpi-3.17-rc7' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are regression fixes (ACPI hotplug, cpufreq, hibernation, ACPI
LPSS driver), fixes for stuff that never worked correctly (ACPI GPIO
support in some cases and a wrong sign of an error code in the ACPI
core in one place), and one blacklist item for ACPI backlight
handling.
Specifics:
- Revert of a recent hibernation core commit that introduced a NULL
pointer dereference during resume for at least one user (Rafael J
Wysocki).
- Fix for the ACPI LPSS (Low-Power Subsystem) driver to disable
asynchronous PM callback execution for LPSS devices during system
suspend/resume (introduced in 3.16) which turns out to break
ordering expectations on some systems. From Fu Zhonghui.
- cpufreq core fix related to the handling of sysfs nodes during
system suspend/resume that has been broken for intel_pstate since
3.15 from Lan Tianyu.
- Restore the generation of "online" uevents for ACPI container
devices that was removed in 3.14, but some user space utilities
turn out to need them (Rafael J Wysocki).
- The cpufreq core fails to release a lock in an error code path
after changes made in 3.14. Fix from Prarit Bhargava.
- ACPICA and ACPI/GPIO fixes to make the handling of ACPI GPIO
operation regions (which means AML using GPIOs) work correctly in
all cases from Bob Moore and Srinivas Pandruvada.
- Fix for a wrong sign of the ACPI core's create_modalias() return
value in case of an error from Mika Westerberg.
- ACPI backlight blacklist entry for ThinkPad X201s from Aaron Lu"
* tag 'pm+acpi-3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PM / Hibernate: Iterate over set bits instead of PFNs in swsusp_free()"
gpio / ACPI: Use pin index and bit length
ACPICA: Update to GPIO region handler interface.
ACPI / platform / LPSS: disable async suspend/resume of LPSS devices
cpufreq: release policy->rwsem on error
cpufreq: fix cpufreq suspend/resume for intel_pstate
ACPI / scan: Correct error return value of create_modalias()
ACPI / video: disable native backlight for ThinkPad X201s
ACPI / hotplug: Generate online uevents for ACPI containers
Linus Torvalds [Thu, 25 Sep 2014 22:04:06 +0000 (15:04 -0700)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"This is probably not the kind of pull request you want to see that
late in the cycle. Yet, the ACPI refactorization was problematic
again and caused another two issues which need fixing. My holidays
with limited internet (plus travelling) and the developer's illness
didn't help either :(
The details:
- ACPI code was refactored out into a seperate file and as a
side-effect, the i2c-core module got renamed. Jean Delvare
rightfully complained about the rename being problematic for
distributions. So, Mika and I thought the least problematic way to
deal with it is to move all the code back into the main i2c core
source file. This is mainly a huge code move with some #ifdeffery
applied. No functional code changes. Our personal tests and the
testbots did not find problems. (I was thinking about reverting,
too, yet that would also have ~800 lines changed)
- The new ACPI code also had a NULL pointer exception, thanks to
Peter for finding and fixing it.
- Mikko fixed a locking problem by decoupling clock_prepare and
clock_enable.
- Addy learnt that the datasheet was wrong and reimplemented the
frequency setup according to the new algorithm.
- Fan fixed an off-by-one error when copying data
- Janusz fixed a copy'n'paste bug which gave a wrong error message
- Sergei made sure that "don't touch" bits are not accessed"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: acpi: Fix NULL Pointer dereference
i2c: move acpi code back into the core
i2c: rk3x: fix divisor calculation for SCL frequency
i2c: mxs: fix error message in pio transfer
i2c: ismt: use correct length when copy buffer
i2c: rcar: fix RCAR_IRQ_ACK_{RECV|SEND}
i2c: tegra: Move clk_prepare/clk_set_rate to probe
Randy Dunlap [Thu, 25 Sep 2014 18:34:54 +0000 (11:34 -0700)]
MAINTAINERS: new Documentation maintainer
Transfer Documentation maintainership to Jiri Kosina.
Thanks, Jiri.
I'll still be reviewing and working on documentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rafael J. Wysocki [Thu, 25 Sep 2014 21:07:29 +0000 (23:07 +0200)]
Merge branches 'pm-cpufreq' and 'pm-sleep'
* pm-cpufreq:
cpufreq: release policy->rwsem on error
cpufreq: fix cpufreq suspend/resume for intel_pstate
* pm-sleep:
Revert "PM / Hibernate: Iterate over set bits instead of PFNs in swsusp_free()"
Rafael J. Wysocki [Thu, 25 Sep 2014 20:59:30 +0000 (22:59 +0200)]
Merge branches 'acpi-hotplug', 'acpi-scan', 'acpi-lpss', 'acpi-gpio' and 'acpi-video'
* acpi-hotplug:
ACPI / hotplug: Generate online uevents for ACPI containers
* acpi-scan:
ACPI / scan: Correct error return value of create_modalias()
* acpi-lpss:
ACPI / platform / LPSS: disable async suspend/resume of LPSS devices
* acpi-gpio:
gpio / ACPI: Use pin index and bit length
ACPICA: Update to GPIO region handler interface.
* acpi-video:
ACPI / video: disable native backlight for ThinkPad X201s
Linus Torvalds [Thu, 25 Sep 2014 17:17:37 +0000 (10:17 -0700)]
Merge tag 'gpio-v3.17-4' of git://git./linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
"Two GPIO fixes:
- GPIO direction flags where handled wrong in the new descriptor-
based API, so direction changes did not always "take".
- Fix a handler installation race in the generic GPIO irqchip code"
* tag 'gpio-v3.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Fix potential NULL handler data in chained irqchip handler
gpio: Fix gpio direction flags not getting set
Linus Torvalds [Thu, 25 Sep 2014 14:39:29 +0000 (07:39 -0700)]
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree bug fixes and documentation from Grant Likely:
"Several bug fix commits for issues found in the v3.17 rc series.
Most of these are minor in that they aren't actively dangerous, but
they have been seen in the wild. The one important fix is commit
7dbe5849fb50 ("of: make sure of_alias is initialized before accessing
it"), without which some powerpc platforms will fail to find stdout
for the console"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of/fdt: fix memory range check
of: Fix memory block alignment in early_init_dt_add_memory_arch()
of: make sure of_alias is initialized before accessing it
of: Documentation regarding attaching OF Selftest testdata
of: Disabling OF functions that use sysfs if CONFIG_SYSFS disabled
of: correct of_console_check()'s return value
Peter Hüwe [Fri, 12 Sep 2014 19:09:47 +0000 (21:09 +0200)]
i2c: acpi: Fix NULL Pointer dereference
If adapter->dev.parent == NULL there is a NULL pointer dereference in
acpi_i2c_install_space_handler and acpi_i2c_remove_space_handler.
This is present since introduction of this code:
366047515c6e "i2c: rework kernel config I2C_ACPI" or even
da3c6647ee08 "I2C/ACPI: Clean up I2C ACPI code and Add CONFIG_I2C_ACPI"
The adapter->dev.parent == NULL case is valid for the i2c_stub,
so loading i2c_stub with ACPI_I2C_OPREGION enabled results in an oops.
This is also valid at least for i2c_tiny_usb and i2c_robotfuzz_osif.
Fix by checking whether it is null before calling ACPI_HANDLE.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Mon, 22 Sep 2014 17:41:00 +0000 (19:41 +0200)]
i2c: move acpi code back into the core
Commit
5d98e61d337c ("I2C/ACPI: Add i2c ACPI operation region support")
renamed the i2c-core module. This may cause regressions for
distributions, so put the ACPI code back into the core.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Lan Tianyu <tianyu.lan@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Srinivas Kandagatla [Tue, 23 Sep 2014 09:59:09 +0000 (10:59 +0100)]
of/fdt: fix memory range check
In cases where board has below memory DT node
memory{
device_type = "memory";
reg = <0x80000000 0x80000000>;
};
Check on the memory range in fdt.c will always fail because it is
comparing MAX_PHYS_ADDR with base + size, in fact it should compare
it with base + size - 1.
This issue was originally noticed on Qualcomm IFC6410 board.
Without this patch kernel shows up noticed unnecessary warnings
[ 0.000000] Machine model: Qualcomm APQ8064/IFC6410
[ 0.000000] Ignoring memory range 0xffffffff - 0x100000000
[ 0.000000] cma: Reserved 64 MiB at
ab800000
as a result the size get reduced to 0x7fffffff which looks wrong.
This patch fixes the check involved in generating this warning and
as a result it also fixes the wrong size calculation.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
[grant.likely: adjust new size calculation also]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Marcos Paulo de Souza [Wed, 24 Sep 2014 23:00:33 +0000 (16:00 -0700)]
Input: i8042 - fix Asus X450LCP touchpad detection
We need to add this module to the nomux table to be able to detect the
touchpad.
Cc: stablevger.kernel.org
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rafael J. Wysocki [Wed, 24 Sep 2014 22:53:44 +0000 (00:53 +0200)]
Revert "PM / Hibernate: Iterate over set bits instead of PFNs in swsusp_free()"
Revert commit
6efde38f0769 (PM / Hibernate: Iterate over set bits
instead of PFNs in swsusp_free()) that introduced a NULL pointer
dereference during system resume from hibernation:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<
ffffffff810a8cc1>] swsusp_free+0x21/0x190
PGD
b39c2067 PUD
b39c1067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in: <irrelevant list of modules>
CPU: 1 PID: 4898 Comm: s2disk Tainted: G C 3.17-rc5-amd64 #1 Debian 3.17~rc5-1~exp1
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
task:
ffff88023155ea40 ti:
ffff8800b3b14000 task.ti:
ffff8800b3b14000
RIP: 0010:[<
ffffffff810a8cc1>] [<
ffffffff810a8cc1>]
swsusp_free+0x21/0x190
RSP: 0018:
ffff8800b3b17ea8 EFLAGS:
00010246
RAX:
0000000000000000 RBX:
ffff8800b39bab00 RCX:
0000000000000001
RDX:
ffff8800b39bab10 RSI:
ffff8800b39bab00 RDI:
0000000000000000
RBP:
0000000000000010 R08:
0000000000000000 R09:
0000000000000000
R10:
ffff8800b39bab10 R11:
0000000000000246 R12:
ffffea0000000000
R13:
ffff880232f485a0 R14:
ffff88023ac27cd8 R15:
ffff880232927590
FS:
00007f406d83b700(0000) GS:
ffff88023bc80000(0000)
knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
000000008005003b
CR2:
0000000000000000 CR3:
00000000b3a62000 CR4:
00000000000007e0
Stack:
ffff8800b39bab00 0000000000000010 ffff880232927590 ffffffff810acb4a
ffff8800b39bab00 ffffffff811a955a ffff8800b39bab10 0000000000000000
ffff88023155f098 ffffffff81a6b8c0 ffff88023155ea40 0000000000000007
Call Trace:
[<
ffffffff810acb4a>] ? snapshot_release+0x2a/0xb0
[<
ffffffff811a955a>] ? __fput+0xca/0x1d0
[<
ffffffff81080627>] ? task_work_run+0x97/0xd0
[<
ffffffff81012d89>] ? do_notify_resume+0x69/0xa0
[<
ffffffff8151452a>] ? int_signal+0x12/0x17
Code: 66 2e 0f 1f 84 00 00 00 00 00 66 66 66 66 90 41 54 48 8b 05 ba 62 9c 00 49 bc 00 00 00 00 00 ea ff ff 48 8b 3d a1 62 9c 00 55 53 <48> 8b 10 48 89 50 18 48 8b 52 20 48 c7 40 28 00 00 00 00 c7 40
RIP [<
ffffffff810a8cc1>] swsusp_free+0x21/0x190
RSP <
ffff8800b3b17ea8>
CR2:
0000000000000000
---[ end trace
f02be86a1ec0cccb ]---
due to forbidden_pages_map being NULL in swsusp_free().
Fixes:
6efde38f0769 "PM / Hibernate: Iterate over set bits instead of PFNs in swsusp_free()"
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Wed, 24 Sep 2014 22:57:55 +0000 (15:57 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Some final radeon and i915 fixes, black screens mostly"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/cik: use a separate counter for CP init timeout
drm/i915/hdmi: fix hdmi audio state readout
drm/i915: Don't leak command parser tables on suspend/resume
drm/radeon: add PX quirk for asus K53TK
drm/radeon: add a backlight quirk for Amilo Xi 2550
drm/radeon: add a module parameter for backlight control (v2)
drm/radeon: Update IH_RB_RPTR register after each processed interrupt
drm/radeon: Make IH ring overflow debugging output more useful
drm/radeon: Clear RB_OVERFLOW bit earlier
Srinivas Pandruvada [Tue, 23 Sep 2014 02:35:54 +0000 (10:35 +0800)]
gpio / ACPI: Use pin index and bit length
Fix code when the operation region callback is for an gpio, which
is not at index 0 and for partial pins in a GPIO definition.
For example:
Name (GMOD, ResourceTemplate ()
{
//3 Outputs that define the Power mode of the device
GpioIo (Exclusive, PullDown, , , , "\\_SB.GPI2") {10, 11, 12}
})
}
If opregion callback calls is for:
- Set pin 10, then address = 0 and bit length = 1
- Set pin 11, then address = 1 and bit length = 1
- Set for both pin 11 and pin 12, then address = 1, bit length = 2
This change requires updated ACPICA gpio operation handler code to
send the pin index and bit length.
Fixes:
473ed7be0da0 (gpio / ACPI: Add support for ACPI GPIO operation regions)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+: 75ec6e55f138 ACPICA: Update to GPIO region handler interface.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bob Moore [Tue, 23 Sep 2014 02:35:47 +0000 (10:35 +0800)]
ACPICA: Update to GPIO region handler interface.
Changes to correct several GPIO issues:
1) The update_rule in a GPIO field definition is now ignored;
a read-modify-write operation is never performed for GPIO fields.
(Internally, this means that the field assembly/disassembly
code is completely bypassed for GPIO.)
2) The Address parameter passed to a GPIO region handler is
now the bit offset of the field from a previous Connection()
operator. Thus, it becomes a "Pin Number Index" into the
Connection() resource descriptor.
3) The bit_width parameter passed to a GPIO region handler is
now the exact bit width of the GPIO field. Thus, it can be
interpreted as "number of pins".
Overall, we can now say that the region handler interface
to GPIO handlers is a raw "bit/pin" addressed interface, not
a byte-addressed interface like the system_memory handler interface.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dave Airlie [Wed, 24 Sep 2014 20:49:26 +0000 (06:49 +1000)]
Merge branch 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
- fix a backlight regression resulting in dark screen
- add a PX quirk to avoid a hang with runtime pm
- fix an init issue on the CIK compute rings
- fix IH ring buffer overflows gracefully
* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/cik: use a separate counter for CP init timeout
drm/radeon: add PX quirk for asus K53TK
drm/radeon: add a backlight quirk for Amilo Xi 2550
drm/radeon: add a module parameter for backlight control (v2)
drm/radeon: Update IH_RB_RPTR register after each processed interrupt
drm/radeon: Make IH ring overflow debugging output more useful
drm/radeon: Clear RB_OVERFLOW bit earlier
Dave Airlie [Wed, 24 Sep 2014 20:48:26 +0000 (06:48 +1000)]
Merge tag 'drm-intel-fixes-2014-09-24' of git://anongit.freedesktop.org/drm-intel into drm-fixes
a couple of small fixes for 3.17 still.
* tag 'drm-intel-fixes-2014-09-24' of git://anongit.freedesktop.org/drm-intel:
drm/i915/hdmi: fix hdmi audio state readout
drm/i915: Don't leak command parser tables on suspend/resume
Fu Zhonghui [Wed, 24 Sep 2014 20:42:26 +0000 (22:42 +0200)]
ACPI / platform / LPSS: disable async suspend/resume of LPSS devices
On some systems (Asus T100 in particular) there are strict ordering
dependencies between LPSS devices with respect to power management
that break if they suspend/resume asynchronously.
In theory it should be possible to follow those dependencies in the
async suspend/resume case too (the ACPI tables tell as that the
dependencies are there), but since we're missing infrastructure
for that at the moment, disable async suspend/resume for all of
the LPSS devices for the time being.
Link: http://marc.info/?l=linux-acpi&m=141158962321905&w=2
Fixes:
8ce62f85a81f (ACPI / platform / LPSS: Enable async suspend/resume of LPSS devices)
Signed-off-by: Li Aubrey <aubrey.li@linux.intel.com>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Wed, 24 Sep 2014 19:45:24 +0000 (12:45 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"Here is a quick pull request primarily meant to address the deconfig
fallout from changing SCSI_NETLINK from being used via 'select' to
being used via 'depends'.
I applied a set of 5 patches written by Michal Marek, and then I
carefully audited all of the remaining config files, basically:
1) I scanned every arch config file, and if it mentioned CONFIG_INET
or CONFIG_UNIX, I made sure it had CONFIG_NET=y
2) After that, I scanned every arch config file, and if it did not
have CONFIG_NET=y I made sure it did not reference any networking
config options.
Finally, we have some late breaking wireless fixes in here from John
Linville and co"
[ And there's a sparc bpf fix snuck in too ]
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
sparc: bpf_jit: fix loads from negative offsets
parisc: Update defconfigs which were missing CONFIG_NET.
powerpc: Update defconfigs which were missing CONFIG_NET.
s390: Update defconfigs which were missing CONFIG_NET.
mips: Update some more defconfigs which were missing CONFIG_NET.
sparc: Set CONFIG_NET=y in defconfigs
sh: Set CONFIG_NET=y in defconfigs
powerpc: Set CONFIG_NET=y in defconfigs
parisc: Set CONFIG_NET=y in defconfigs
mips: Set CONFIG_NET=y in defconfigs
brcmfmac: Fix off by one bug in brcmf_count_20mhz_channels()
ath9k: Fix NULL pointer dereference on early irq
net: rfkill: gpio: Fix clock status
NFC: st21nfca: Fix potential depmod dependency cycle
NFC: st21nfcb: Fix depmod dependency cycle
NFC: microread: Potential overflows in microread_target_discovered()
Alexei Starovoitov [Tue, 23 Sep 2014 20:50:10 +0000 (13:50 -0700)]
sparc: bpf_jit: fix loads from negative offsets
- fix BPF_LD|ABS|IND from negative offsets:
make sure to sign extend lower 32 bits in 64-bit register
before calling C helpers from JITed code, otherwise 'int k'
argument of bpf_internal_load_pointer_neg_helper() function
will be added as large unsigned integer, causing packet size
check to trigger and abort the program.
It's worth noting that JITed code for 'A = A op K' will affect
upper 32 bits differently depending whether K is simm13 or not.
Since small constants are sign extended, whereas large constants
are stored in temp register and zero extended.
That is ok and we don't have to pay a penalty of sign extension
for every sethi, since all classic BPF instructions have 32-bit
semantics and we only need to set correct upper bits when
transitioning from JITed code into C.
- though instructions 'A &= 0' and 'A *= 0' are odd, JIT compiler
should not optimize them out
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Sep 2014 19:00:12 +0000 (15:00 -0400)]
Merge tag 'master-2014-09-23' of git://git./linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-09-23
Please consider pulling this one last batch of fixes intended for the 3.17 stream!
For the NFC bits, Samuel says:
"Hopefully not too late for a handful of NFC fixes:
- 2 potential build failures for ST21NFCA and ST21NFCB, triggered by a
depmod dependenyc cycle.
- One potential buffer overflow in the microread driver."
On top of that...
Emil Goode provides a fix for a brcmfmac off-by-one regression which
was introduced in the 3.17 cycle.
Loic Poulain fixes a polarity mismatch for a variable assignment
inside of rfkill-gpio.
Wojciech Dubowik prevents a NULL pointer dereference in ath9k.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Sep 2014 17:53:53 +0000 (13:53 -0400)]
parisc: Update defconfigs which were missing CONFIG_NET.
Commit
df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Sep 2014 17:53:43 +0000 (13:53 -0400)]
powerpc: Update defconfigs which were missing CONFIG_NET.
Commit
df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Sep 2014 17:44:32 +0000 (13:44 -0400)]
s390: Update defconfigs which were missing CONFIG_NET.
Commit
df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Sep 2014 17:44:16 +0000 (13:44 -0400)]
mips: Update some more defconfigs which were missing CONFIG_NET.
Commit
df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Marek [Tue, 23 Sep 2014 15:44:04 +0000 (17:44 +0200)]
sparc: Set CONFIG_NET=y in defconfigs
Commit
5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Marek [Tue, 23 Sep 2014 15:44:03 +0000 (17:44 +0200)]
sh: Set CONFIG_NET=y in defconfigs
Commit
5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Marek [Tue, 23 Sep 2014 15:44:02 +0000 (17:44 +0200)]
powerpc: Set CONFIG_NET=y in defconfigs
Commit
5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Marek [Tue, 23 Sep 2014 15:44:01 +0000 (17:44 +0200)]
parisc: Set CONFIG_NET=y in defconfigs
Commit
5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Marek [Tue, 23 Sep 2014 15:44:00 +0000 (17:44 +0200)]
mips: Set CONFIG_NET=y in defconfigs
Commit
5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-mips@linux-mips.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 24 Sep 2014 16:51:50 +0000 (09:51 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull one last block fix from Jens Axboe:
"We've had an issue with scsi-mq where probing takes forever. This was
bisected down to the percpu changes for blk_mq_queue_enter(), and the
fact we now suffer an RCU grace period when killing a queue. SCSI
creates and destroys tons of queues, so this let to 10s of seconds of
stalls at boot for some.
Tejun has a real fix for this, but it's too involved for 3.17. So
this is a temporary workaround to expedite the queue killing until we
can fold in the real fix for 3.18 when that merge window opens"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq, percpu_ref: implement a kludge for SCSI blk-mq stall during probe
Linus Torvalds [Wed, 24 Sep 2014 16:46:29 +0000 (09:46 -0700)]
Merge tag 'pci-v3.17-fixes-3' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are a few fixes that should be in v3.17.
- Reverting "Don't scan random busses" covers up a CardBus regression
having to do with allocating CardBus bus numbers.
- Reverting "Make sure bus numbers stay within parents bounds" covers
up an ACPI _CRS bug that makes us reconfigure a bridge, causing a
broken device behind it to stop responding.
- The pciehp timeout change fixes some code we added in v3.17.
Without the fix, we can send a new hotplug command too early,
before the timeout has expired.
I hope for better fixes for the reverts, but those will have to come
after v3.17"
* tag 'pci-v3.17-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: pciehp: Fix pcie_wait_cmd() timeout
Revert "PCI: Make sure bus number resources stay within their parents bounds"
Revert "PCI: Don't scan random busses in pci_scan_bridge()"
Linus Torvalds [Wed, 24 Sep 2014 16:37:35 +0000 (09:37 -0700)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes three issues:
- if ccp is loaded on a machine without ccp, it will incorrectly
activate causing all requests to fail. Fixed by preventing ccp
from loading if hardware isn't available.
- not all IRQs were enabled for the qat driver, leading to potential
stalls when it is used
- disabled buggy AVX CTR implementation in aesni"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aesni - disable "by8" AVX CTR optimization
crypto: ccp - Check for CCP before registering crypto algs
crypto: qat - Enable all 32 IRQs
Linus Torvalds [Wed, 24 Sep 2014 16:03:43 +0000 (09:03 -0700)]
Merge tag 'media/v3.17-rc7' of git://git./linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"For some last time fixes:
- a regression detected on Kernel 3.16 related to VBI Teletext
application breakage on drivers using videobuf2 (see
https://bugzilla.kernel.org/show_bug.cgi?id=84401). The bug was
noticed on saa7134 (migrated to VB2 on 3.16), but also affects
em28xx (migrated on 3.9 to VB2);
- two additional sanity checks at videobuf2;
- two fixups to restore proper VBI support at the em28xx driver;
- two Kernel oops fixups (at cx24123 and cx2341x drivers);
- a bug at adv7604 where an if was doing just the opposite as it
would be expected;
- some documentation fixups to match the behavior defined at the
Kernel"
* tag 'media/v3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] em28xx-v4l: get rid of field "users" in struct em28xx_v4l2"
[media] em28xx: fix VBI handling logic
[media] DocBook media: improve the poll() documentation
[media] DocBook media: fix the poll() 'no QBUF' documentation
[media] vb2: fix VBI/poll regression
[media] cx2341x: fix kernel oops
[media] cx24123: fix kernel oops due to missing parent pointer
[media] adv7604: fix inverted condition
[media] media/radio: fix radio-miropcm20.c build with io.h header file
[media] vb2: fix plane index sanity check in vb2_plane_cookie()
[media] DocBook media: update version number and V4L2 changes
[media] DocBook media: fix fieldname in struct v4l2_subdev_selection
[media] vb2: fix vb2 state check when start_streaming fails
[media] videobuf2-core.h: fix comment
[media] videobuf2-core: add comments before the WARN_ON
[media] videobuf2-dma-sg: fix for wrong GFP mask to sg_alloc_table_from_pages
Linus Torvalds [Wed, 24 Sep 2014 15:53:33 +0000 (08:53 -0700)]
Merge tag 'md/3.17-more-fixes' of git://git.neil.brown.name/md
Pull bugfixes for md/raid1 from Neil Brown:
"It is amazing how much easier it is to find bugs when you know one is
there. Two bug reports resulted in finding 7 bugs!
All are tagged for -stable. Those that can't cause (rare) data
corruption, cause lockups.
Particularly, but not only, fixing new "resync" code"
* tag 'md/3.17-more-fixes' of git://git.neil.brown.name/md:
md/raid1: fix_read_error should act on all non-faulty devices.
md/raid1: count resync requests in nr_pending.
md/raid1: update next_resync under resync_lock.
md/raid1: Don't use next_resync to determine how far resync has progressed
md/raid1: make sure resync waits for conflicting writes to complete.
md/raid1: clean up request counts properly in close_sync()
md/raid1: be more cautious where we read-balance during resync.
md/raid1: intialise start_next_window for READ case to avoid hang
Tejun Heo [Tue, 23 Sep 2014 19:24:32 +0000 (15:24 -0400)]
blk-mq, percpu_ref: implement a kludge for SCSI blk-mq stall during probe
blk-mq uses percpu_ref for its usage counter which tracks the number
of in-flight commands and used to synchronously drain the queue on
freeze. percpu_ref shutdown takes measureable wallclock time as it
involves a sched RCU grace period. This means that draining a blk-mq
takes measureable wallclock time. One would think that this shouldn't
matter as queue shutdown should be a rare event which takes place
asynchronously w.r.t. userland.
Unfortunately, SCSI probing involves synchronously setting up and then
tearing down a lot of request_queues back-to-back for non-existent
LUNs. This means that SCSI probing may take more than ten seconds
when scsi-mq is used.
This will be properly fixed by implementing a mechanism to keep
q->mq_usage_counter in atomic mode till genhd registration; however,
that involves rather big updates to percpu_ref which is difficult to
apply late in the devel cycle (v3.17-rc6 at the moment). As a
stop-gap measure till the proper fix can be implemented in the next
cycle, this patch introduces __percpu_ref_kill_expedited() and makes
blk_mq_freeze_queue() use it. This is heavy-handed but should work
for testing the experimental SCSI blk-mq implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Christoph Hellwig <hch@infradead.org>
Link: http://lkml.kernel.org/g/20140919113815.GA10791@lst.de
Fixes:
add703fda981 ("blk-mq: use percpu_ref for mq usage count")
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Tested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Mathias Krause [Tue, 23 Sep 2014 20:31:07 +0000 (22:31 +0200)]
crypto: aesni - disable "by8" AVX CTR optimization
The "by8" implementation introduced in commit
22cddcc7df8f ("crypto: aes
- AES CTR x86_64 "by8" AVX optimization") is failing crypto tests as it
handles counter block overflows differently. It only accounts the right
most 32 bit as a counter -- not the whole block as all other
implementations do. This makes it fail the cryptomgr test #4 that
specifically tests this corner case.
As we're quite late in the release cycle, just disable the "by8" variant
for now.
Reported-by: Romain Francoise <romain@orebokech.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Chandramouli Narayanan <mouli@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Wanpeng Li [Wed, 24 Sep 2014 08:38:05 +0000 (16:38 +0800)]
sched: Fix unreleased llc_shared_mask bit during CPU hotplug
The following bug can be triggered by hot adding and removing a large number of
xen domain0's vcpus repeatedly:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000004 IP: [..] find_busiest_group
PGD
5a9d5067 PUD 13067 PMD 0
Oops: 0000 [#3] SMP
[...]
Call Trace:
load_balance
? _raw_spin_unlock_irqrestore
idle_balance
__schedule
schedule
schedule_timeout
? lock_timer_base
schedule_timeout_uninterruptible
msleep
lock_device_hotplug_sysfs
online_store
dev_attr_store
sysfs_write_file
vfs_write
SyS_write
system_call_fastpath
Last level cache shared mask is built during CPU up and the
build_sched_domain() routine takes advantage of it to setup
the sched domain CPU topology.
However, llc_shared_mask is not released during CPU disable,
which leads to an invalid sched domainCPU topology.
This patch fix it by releasing the llc_shared_mask correctly
during CPU disable.
Yasuaki also reported that this can happen on real hardware:
https://lkml.org/lkml/2014/7/22/1018
His case is here:
==
Here is an example on my system.
My system has 4 sockets and each socket has 15 cores and HT is
enabled. In this case, each core of sockes is numbered as
follows:
| CPU#
Socket#0 | 0-14 , 60-74
Socket#1 | 15-29, 75-89
Socket#2 | 30-44, 90-104
Socket#3 | 45-59, 105-119
Then llc_shared_mask of CPU#30 has 0x3fff80000001fffc0000000.
It means that last level cache of Socket#2 is shared with
CPU#30-44 and 90-104.
When hot-removing socket#2 and #3, each core of sockets is
numbered as follows:
| CPU#
Socket#0 | 0-14 , 60-74
Socket#1 | 15-29, 75-89
But llc_shared_mask is not cleared. So llc_shared_mask of CPU#30
remains having 0x3fff80000001fffc0000000.
After that, when hot-adding socket#2 and #3, each core of
sockets is numbered as follows:
| CPU#
Socket#0 | 0-14 , 60-74
Socket#1 | 15-29, 75-89
Socket#2 | 30-59
Socket#3 | 90-119
Then llc_shared_mask of CPU#30 becomes
0x3fff8000fffffffc0000000. It means that last level cache of
Socket#2 is shared with CPU#30-59 and 90-104. So the mask has
the wrong value.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Tested-by: Linn Crosetto <linn@hp.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1411547885-48165-1-git-send-email-wanpeng.li@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jarkko Nikula [Tue, 16 Sep 2014 13:23:15 +0000 (16:23 +0300)]
gpio: Fix potential NULL handler data in chained irqchip handler
There is possibility with misconfigured pins that interrupt occurs instantly
after setting irq_set_chained_handler() in gpiochip_set_chained_irqchip().
Now if handler gets called before irq_set_handler_data() the handler gets
NULL handler data.
Fix this by moving irq_set_handler_data() call before
irq_set_chained_handler() in gpiochip_set_chained_irqchip().
Cc: Stable <stable@vger.kernel.org> # 3.15+
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Adrian Hunter [Mon, 22 Sep 2014 08:01:16 +0000 (11:01 +0300)]
gpio: Fix gpio direction flags not getting set
GPIO direction flags are not getting set because
an 'if' statement is the wrong way around.
Cc: Stable <stable@vger.kernel.org> # 3.15+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tom Lendacky [Fri, 5 Sep 2014 15:31:09 +0000 (10:31 -0500)]
crypto: ccp - Check for CCP before registering crypto algs
If the ccp is built as a built-in module, then ccp-crypto (whether
built as a module or a built-in module) will be able to load and
it will register its crypto algorithms. If the system does not have
a CCP this will result in -ENODEV being returned whenever a command
is attempted to be queued by the registered crypto algorithms.
Add an API, ccp_present(), that checks for the presence of a CCP
on the system. The ccp-crypto module can use this to determine if it
should register it's crypto alogorithms.
Cc: stable@vger.kernel.org
Reported-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Linus Torvalds [Tue, 23 Sep 2014 23:47:34 +0000 (16:47 -0700)]
Merge tag 'rdma-for-linus' of git://git./linux/kernel/git/roland/infiniband
Pull infiniband/rdma fixes from Roland Dreier:
"Last late set of InfiniBand/RDMA fixes for 3.17:
- fixes for the new memory region re-registration support
- iSER initiator error path fixes
- grab bag of small fixes for the qib and ocrdma hardware drivers
- larger set of fixes for mlx4, especially in RoCE mode"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (26 commits)
IB/mlx4: Fix VF mac handling in RoCE
IB/mlx4: Do not allow APM under RoCE
IB/mlx4: Don't update QP1 in native mode
IB/mlx4: Avoid accessing netdevice when building RoCE qp1 header
mlx4: Fix mlx4 reg/unreg mac to work properly with 0-mac addresses
IB/core: When marshaling uverbs path, clear unused fields
IB/mlx4: Avoid executing gid task when device is being removed
IB/mlx4: Fix lockdep splat for the iboe lock
IB/mlx4: Get upper dev addresses as RoCE GIDs when port comes up
IB/mlx4: Reorder steps in RoCE GID table initialization
IB/mlx4: Don't duplicate the default RoCE GID
IB/mlx4: Avoid null pointer dereference in mlx4_ib_scan_netdevs()
IB/iser: Bump version to 1.4.1
IB/iser: Allow bind only when connection state is UP
IB/iser: Fix RX/TX CQ resource leak on error flow
RDMA/ocrdma: Use right macro in query AH
RDMA/ocrdma: Resolve L2 address when creating user AH
mlx4: Correct error flows in rereg_mr
IB/qib: Correct reference counting in debugfs qp_stats
IPoIB: Remove unnecessary port query
...
Linus Torvalds [Tue, 23 Sep 2014 21:47:11 +0000 (14:47 -0700)]
Merge tag 'sound-3.17-rc7' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"One fix is about a buggy computation in PCM API function Clemens
spotted out, but the impact must be really small as no one really uses
it in user-space side.
The rest are a trivial fix for a HD-audio model and a USB-audio
device-specific regression fix, so all look fairly safe to apply"
* tag 'sound-3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: snd-usb-caiaq: Fix LED commands for Kore controller
ALSA: pcm: fix fifo_size frame calculation
ALSA: hda - Add fixup model name lookup for Lemote A1205
Linus Torvalds [Tue, 23 Sep 2014 21:45:09 +0000 (14:45 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull final block fixes from Jens Axboe:
"This week and last we've been fixing some corner cases related to
blk-mq, mostly. I ended up pulling most of that out of for-linus
yesterday, which is why the branch looks fresh. The rest were
postponed for 3.18.
This pull request contains:
- Fix from Christoph, avoiding a stack overflow when FUA insertion
would recursive infinitely.
- Fix from David Hildenbrand on races between the timeout handler and
uninitialized requests. Fixes a real issue that virtio_blk has run
into.
- A few fixes from me:
- Ensure that request deadline/timeout is ordered before the
request is marked as started.
- A potential oops on out-of-memory, when we scale the queue
depth of the device and retry.
- A hang fix on requeue from SCSI, where the hardware queue
would be stopped when we attempt to re-run it (and hence
nothing would happen, stalling progress).
- A fix for commit
2da78092, where the cleanup path was moved
to RCU, but a debug might_sleep() was inadvertently left in
the code. This causes warnings for people"
* 'for-linus' of git://git.kernel.dk/linux-block:
genhd: fix leftover might_sleep() in blk_free_devt()
blk-mq: use blk_mq_start_hw_queues() when running requeue work
blk-mq: fix potential oops on out-of-memory in __blk_mq_alloc_rq_maps()
blk-mq: avoid infinite recursion with the FUA flag
blk-mq: Avoid race condition with uninitialized requests
blk-mq: request deadline must be visible before marking rq as started
Linus Torvalds [Tue, 23 Sep 2014 21:05:32 +0000 (14:05 -0700)]
Merge branch 'parisc-3.17-7' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"We avoid using -mfast-indirect-calls for 64bit kernel builds to
prevent building an unbootable kernel due to latest gcc changes.
In the pdc_stable/firmware-access driver we fix a few possible stack
overflows and we now call secure_computing_strict() instead of
secure_computing() which fixes upcoming SECCOMP patches in the
for-next trees"
* 'parisc-3.17-7' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Only use -mfast-indirect-calls option for 32-bit kernel builds
parisc: pdc_stable.c: Avoid potential stack overflows
parisc: pdc_stable.c: Cleaning up unnecessary use of memset in conjunction with strncpy
parisc: ptrace: use secure_computing_strict()
John David Anglin [Tue, 23 Sep 2014 00:54:50 +0000 (20:54 -0400)]
parisc: Only use -mfast-indirect-calls option for 32-bit kernel builds
In spite of what the GCC manual says, the -mfast-indirect-calls has
never been supported in the 64-bit parisc compiler. Indirect calls have
always been done using function descriptors irrespective of the
-mfast-indirect-calls option.
Recently, it was noticed that a function descriptor was always requested
when the -mfast-indirect-calls option was specified. This caused
problems when the option was used in application code and doesn't make
any sense because the whole point of the option is to avoid using a
function descriptor for indirect calls.
Fixing this broke 64-bit kernel builds.
I will fix GCC but for now we need the attached change. This results in
the same kernel code as before.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.0+
Signed-off-by: Helge Deller <deller@gmx.de>
Linus Torvalds [Tue, 23 Sep 2014 19:10:48 +0000 (12:10 -0700)]
Merge tag 'please-pull-defconfig' of git://git./linux/kernel/git/aegl/linux
Pull ia64 defconfig update from Tony Luck:
"Need to rebuild defconfig files to cope with removal of "select NET"
in drivers/scsi/Kconfig"
* tag 'please-pull-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] refresh arch/ia64/configs/* using "make savedefconfig"
Linus Torvalds [Tue, 23 Sep 2014 18:53:28 +0000 (11:53 -0700)]
Merge tag 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix a resource leak in tmp103 driver
- Add support for two more processors to fam15h_power driver
- Also fix a bug in the same driver to only report the power level on
chips which actually support reporting it
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (tmp103) Fix resource leak bug in tmp103 temperature sensor driver
hwmon: (fam15h_power) Add support for two more processors
hwmon: (fam15h_power) Make actual power reporting conditional
Tony Luck [Mon, 22 Sep 2014 16:35:11 +0000 (09:35 -0700)]
[IA64] refresh arch/ia64/configs/* using "make savedefconfig"
Prompted by a change to drivers/scsi/Kconfig which used to do a
"select NET" but now does a "depends on NET". This meant that some
configurations ended up without CONFIG_NET=y
Signed-off-by Tony Luck <tony.luck@intel.com>
Linus Torvalds [Tue, 23 Sep 2014 16:13:43 +0000 (09:13 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull another kvm fix from Paolo Bonzini:
"Another fix for 3.17 arrived at just the wrong time, after I had sent
yesterday's pull request. Normally I would have waited for some other
patches to pile up, but since 3.17 might be short here it is"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
arm/arm64: KVM: Fix unaligned access bug on gicv2 access
Linus Torvalds [Tue, 23 Sep 2014 16:06:18 +0000 (09:06 -0700)]
Merge branch 'for-3.17-fixes' of git://git./linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"One late fix for cgroup.
I was waiting for another set of fixes for a long-standing obscure
cpuset bug but am not sure whether they'll be ready before v3.17
release. This one is a simple fix for a mutex unlock balance bug in
an allocation failure path in pidlist_array_load().
The bug was introduced in v3.14 and the fix is tagged for -stable"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: fix unbalanced locking
Emil Goode [Mon, 22 Sep 2014 22:49:55 +0000 (00:49 +0200)]
brcmfmac: Fix off by one bug in brcmf_count_20mhz_channels()
In the brcmf_count_20mhz_channels function we are looping through a list
of channels received from firmware. Since the index of the first channel
is 0 the condition leads to an off by one bug. This is causing us to hit
the WARN_ON_ONCE(1) calls in the brcmu_d11n_decchspec function, which is
how I discovered the bug.
Introduced by:
commit
b48d891676f756d48b4d0ee131e4a7a5d43ca417
("brcmfmac: rework wiphy structure setup")
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alex Deucher [Tue, 23 Sep 2014 14:20:13 +0000 (10:20 -0400)]
drm/radeon/cik: use a separate counter for CP init timeout
Otherwise we may fail to init the second compute ring.
Noticed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Jani Nikula [Wed, 17 Sep 2014 12:34:58 +0000 (15:34 +0300)]
drm/i915/hdmi: fix hdmi audio state readout
Check the correct bit for audio. Seems like a copy-paste error from the
start:
commit
9ed109a7b445e3f073d8ea72f888ec80c0532465
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Apr 24 23:54:52 2014 +0200
drm/i915: Track has_audio in the pipe config
Reported-by: Martin Andersen <martin.x.andersen@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82756
Cc: stable@vger.kernel.org # 3.16+
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Paolo Bonzini [Tue, 23 Sep 2014 13:18:02 +0000 (15:18 +0200)]
Merge tag 'kvm-arm-for-v3.17-rc7-or-final' of git://git./linux/kernel/git/kvmarm/kvmarm into kvm-master
Fixes unaligned access to the gicv2 virtual cpu status.
Brad Volkin [Mon, 22 Sep 2014 15:25:21 +0000 (08:25 -0700)]
drm/i915: Don't leak command parser tables on suspend/resume
Ring init and cleanup are not balanced because we re-init the rings on
resume without having cleaned them up on suspend. This leads to the
driver leaking the parser's hash tables with a kmemleak signature such
as this:
unreferenced object 0xffff880405960980 (size 32):
comm "systemd-udevd", pid 516, jiffies
4294896961 (age 10202.044s)
hex dump (first 32 bytes):
d0 85 46 c0 ff ff ff ff 00 00 00 00 00 00 00 00 ..F.............
98 60 28 04 04 88 ff ff 00 00 00 00 00 00 00 00 .`(.............
backtrace:
[<
ffffffff81816f9e>] kmemleak_alloc+0x4e/0xb0
[<
ffffffff811fa678>] kmem_cache_alloc_trace+0x168/0x2f0
[<
ffffffffc03e20a5>] i915_cmd_parser_init_ring+0x2a5/0x3e0 [i915]
[<
ffffffffc04088a2>] intel_init_ring_buffer+0x202/0x470 [i915]
[<
ffffffffc040c998>] intel_init_vebox_ring_buffer+0x1e8/0x2b0 [i915]
[<
ffffffffc03eff59>] i915_gem_init_hw+0x2f9/0x3a0 [i915]
[<
ffffffffc03f0057>] i915_gem_init+0x57/0x1d0 [i915]
[<
ffffffffc045e26a>] i915_driver_load+0xc0a/0x10e0 [i915]
[<
ffffffffc02e0d5d>] drm_dev_register+0xad/0x100 [drm]
[<
ffffffffc02e3b9f>] drm_get_pci_dev+0x8f/0x200 [drm]
[<
ffffffffc03c934b>] i915_pci_probe+0x3b/0x60 [i915]
[<
ffffffff81436725>] local_pci_probe+0x45/0xa0
[<
ffffffff81437a69>] pci_device_probe+0xd9/0x130
[<
ffffffff81524f4d>] driver_probe_device+0x12d/0x3e0
[<
ffffffff815252d3>] __driver_attach+0x93/0xa0
[<
ffffffff81522e1b>] bus_for_each_dev+0x6b/0xb0
This patch extends the current convention of checking whether a
resource is already allocated before allocating it during ring init.
Longer term it might make sense to only init the rings once.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83794
Tested-by: Kari Suvanto <kari.tj.suvanto@gmail.com>
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Linus Torvalds [Tue, 23 Sep 2014 06:05:49 +0000 (23:05 -0700)]
Revert "x86/efi: Fixup GOT in all boot code paths"
This reverts commit
9cb0e394234d244fe5a97e743ec9dd7ddff7e64b.
It causes my Sony Vaio Pro 11 to immediately reboot at startup.
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yinghai Lu [Tue, 23 Sep 2014 02:05:45 +0000 (20:05 -0600)]
PCI: pciehp: Fix pcie_wait_cmd() timeout
pcie_poll_cmd() take msecs instead of jiffies, so convert timeout to msecs.
Fixes:
40b960831cfa ("PCI: pciehp: Compute timeout from hotplug command start time")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Linus Torvalds [Tue, 23 Sep 2014 01:23:33 +0000 (18:23 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) If the user gives us a msg_namelen of 0, don't try to interpret
anything pointed to by msg_name. From Ani Sinha.
2) Fix some bnx2i/bnx2fc randconfig compilation errors.
The gist of the issue is that we firstly have drivers that span both
SCSI and networking. And at the top of that chain of dependencies
we have things like SCSI_FC_ATTRS and SCSI_NETLINK which are
selected.
But since select is a sledgehammer and ignores dependencies,
everything to select's SCSI_FC_ATTRS and/or SCSI_NETLINK has to also
explicitly select their dependencies and so on and so forth.
Generally speaking 'select' is supposed to only be used for child
nodes, those which have no dependencies of their own. And this
whole chain of dependencies in the scsi layer violates that rather
strongly.
So just make SCSI_NETLINK depend upon it's dependencies, and so on
and so forth for the things selecting it (either directly or
indirectly).
From Anish Bhatt and Randy Dunlap.
3) Fix generation of blackhole routes in IPSEC, from Steffen Klassert.
4) Actually notice netdev feature changes in rtl_open() code, from
Hayes Wang.
5) Fix divide by zero in bond enslaving, from Nikolay Aleksandrov.
6) Missing memory barrier in sunvnet driver, from David Stevens.
7) Don't leave anycast addresses around when ipv6 interface is
destroyed, from Sabrina Dubroca.
8) Don't call efx_{arch}_filter_sync_rx_mode before addr_list_lock is
initialized in SFC driver, from Edward Cree.
9) Fix missing DMA error checking in 3c59x, from Neal Horman.
10) Openvswitch doesn't emit OVS_FLOW_CMD_NEW notifications accidently,
fix from Samuel Gauthier.
11) pch_gbe needs to select NET_PTP_CLASSIFY otherwise we can get a
build error.
12) Fix macvlan regression wherein we stopped emitting
broadcast/multicast frames over software devices. From Nicolas
Dichtel.
13) Fix infiniband bug due to unintended overflow of skb->cb[], from
Eric Dumazet. And add an assertion so this doesn't happen again.
14) dm9000_parse_dt() should return error pointers, not NULL. From
Tobias Klauser.
15) IP tunneling code uses this_cpu_ptr() in preemptible contexts, fix
from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
net: bcmgenet: call bcmgenet_dma_teardown in bcmgenet_fini_dma
net: bcmgenet: fix TX reclaim accounting for fragments
ipv4: do not use this_cpu_ptr() in preemptible context
dm9000: Return an ERR_PTR() in all error conditions of dm9000_parse_dt()
r8169: fix an if condition
r8152: disable ALDPS
ipoib: validate struct ipoib_cb size
net: sched: shrink struct qdisc_skb_cb to 28 bytes
tg3: Work around HW/FW limitations with vlan encapsulated frames
macvlan: allow to enqueue broadcast pkt on virtual device
pch_gbe: 'select' NET_PTP_CLASSIFY.
scsi: Use 'depends' with LIBFC instead of 'select'.
openvswitch: restore OVS_FLOW_CMD_NEW notifications
genetlink: add function genl_has_listeners()
lib: rhashtable: remove second linux/log2.h inclusion
net: allow macvlans to move to net namespace
3c59x: Fix bad offset spec in skb_frag_dma_map
3c59x: Add dma error checking and recovery
sparc: bpf_jit: fix support for ldx/stx mem and SKF_AD_VLAN_TAG
can: at91_can: add missing prepare and unprepare of the clock
...
Linus Torvalds [Tue, 23 Sep 2014 01:18:55 +0000 (18:18 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux
Pull clock layer fixes from Mike Turquette:
"The fixes for the clock tree are mostly run-time bugs in clock
drivers.
The fixes for TI DRA7 remove divide-by-zero errors. The recently
merged AT91 clock driver fixes some bad error checking and the QCOM
driver fix restores audio for that platform, a clear regression. A
list iteration bug in the framework core was hit recently and is fixed
up here. Finally a compilation warning is fixed for efm32gg, which is
also a regression fix"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk/efm32gg: fix dt init prototype
clk: prevent erronous parsing of children during rate change
clk: rockchip: Fix the clocks for i2c1 and i2c2
clk: qcom: Fix sdc 144kHz frequency entry
clk: at91: fix num_parents test in at91sam9260 slow clk implementation
clk: ti: dra7-atl: Provide error check for incoming parameters in set_rate
clk: ti: divider: Provide error check for incoming parameters in set_rate
Linus Torvalds [Tue, 23 Sep 2014 00:52:16 +0000 (17:52 -0700)]
Merge tag 'fscache-fixes-
20140917' of git://git./linux/kernel/git/dhowells/linux-fs
Pull fs-cache fixes from David Howells:
- Put a timeout in releasepage() to deal with a recursive hang between
the memory allocator, writeback, ext4 and fscache under memory
pressure.
- Fix a pair of refcount bugs in the fscache error handling.
- Remove a couple of unused pagevecs.
- The cachefiles requirement that the base directory support rename
should permit rename2 as an alternative - otherwise certain
filesystems cannot now be used as backing stores (such as ext4).
* tag 'fscache-fixes-
20140917' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
CacheFiles: Handle rename2
cachefiles: remove two unused pagevecs.
FS-Cache: refcount becomes corrupt under vma pressure.
FS-Cache: Reduce cookie ref count if submit fails.
FS-Cache: Timeout for releasepage()
David S. Miller [Mon, 22 Sep 2014 22:38:53 +0000 (18:38 -0400)]
Merge branch 'bcmgenet'
Florian Fainelli says:
====================
net: bcmgenet: TX reclaim and DMA fixes
This patch set contains one fix for an accounting problem while reclaiming
transmitted buffers having fragments, and the second fix is to make sure
that the DMA shutdown is properly controlled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 22 Sep 2014 18:54:43 +0000 (11:54 -0700)]
net: bcmgenet: call bcmgenet_dma_teardown in bcmgenet_fini_dma
We should not be manipulaging the DMA_CTRL registers directly by writing
0 to them to disable DMA. This is an operation that needs to be timed to
make sure the DMA engines have been properly stopped since their state
machine stops on a packet boundary, not immediately.
Make sure that tha bcmgenet_fini_dma() calls bcmgenet_dma_teardown() to
ensure a proper DMA engine state. As a result, we need to reorder the
function bodies to resolve the use dependency.
Fixes:
1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 22 Sep 2014 18:54:42 +0000 (11:54 -0700)]
net: bcmgenet: fix TX reclaim accounting for fragments
The GENET driver supports SKB fragments, and succeeds in transmitting
them properly, but when reclaiming these transmitted fragments, we will
only update the count of free buffer descriptors by 1, even for SKBs
with fragments. This leads to the networking stack thinking it has more
room than the hardware has when pushing new SKBs, and backing off
consequently because we return NETDEV_TX_BUSY.
Fix this by accounting for the SKB nr_frags plus one (itself) and update
ring->free_bds accordingly with that value for each iteration loop in
__bcmgenet_tx_reclaim().
Fixes:
1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 22 Sep 2014 17:38:16 +0000 (10:38 -0700)]
ipv4: do not use this_cpu_ptr() in preemptible context
this_cpu_ptr() in preemptible context is generally bad
Sep 22 05:05:55 br kernel: [ 94.608310] BUG: using smp_processor_id()
in
preemptible [
00000000] code: ip/2261
Sep 22 05:05:55 br kernel: [ 94.608316] caller is
tunnel_dst_set.isra.28+0x20/0x60 [ip_tunnel]
Sep 22 05:05:55 br kernel: [ 94.608319] CPU: 3 PID: 2261 Comm: ip Not
tainted
3.17.0-rc5 #82
We can simply use raw_cpu_ptr(), as preemption is safe in these
contexts.
Should fix https://bugzilla.kernel.org/show_bug.cgi?id=84991
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Joe <joe9mail@gmail.com>
Fixes:
9a4aa9af447f ("ipv4: Use percpu Cache route in IP tunnels")
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Deucher [Mon, 22 Sep 2014 21:28:29 +0000 (17:28 -0400)]
drm/radeon: add PX quirk for asus K53TK
Seems to have problems turning the dGPU on/off.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=51381
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Wed, 17 Sep 2014 15:31:02 +0000 (11:31 -0400)]
drm/radeon: add a backlight quirk for Amilo Xi 2550
Only the acpi backlight seems to work. Using the
radeon backlight controller causes the backlight to
go off.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=81382
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Wed, 17 Sep 2014 00:57:26 +0000 (20:57 -0400)]
drm/radeon: add a module parameter for backlight control (v2)
Add a module parameter to disable the radeon GPU backlight
controller to override the automatic detection. Some
laptops seems to indicate that they use the integrated
controller, but appear to actually use an external
controller.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=81382
v2: fix module parameter description
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Michel Dänzer [Fri, 19 Sep 2014 03:22:10 +0000 (12:22 +0900)]
drm/radeon: Update IH_RB_RPTR register after each processed interrupt
This might decrease the chance of IH ring buffer overflows.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Michel Dänzer [Fri, 19 Sep 2014 03:22:07 +0000 (12:22 +0900)]
drm/radeon: Make IH ring overflow debugging output more useful
Use the same format for all ring indices, and fix the calculation of the
post-overflow RPTR.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Michel Dänzer [Fri, 19 Sep 2014 03:07:11 +0000 (12:07 +0900)]
drm/radeon: Clear RB_OVERFLOW bit earlier
Otherwise the bit remains set in rdev->ih.rptr, so the wptr can never
match that and we still have an infinite loop.
This fix allows me to successfully recover from an IH ring buffer
overflow.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christoffer Dall [Mon, 22 Sep 2014 20:10:36 +0000 (22:10 +0200)]
arm/arm64: KVM: Fix unaligned access bug on gicv2 access
We were using an atomic bitop on the vgic_v2.vgic_elrsr field which was
not aligned to the natural size on 64-bit platforms. This bug showed up
after QEMU correctly identifies the pl011 line as being level-triggered,
and not edge-triggered.
These data structures are protected by a spinlock so simply use a
non-atomic version of the accessor instead.
Tested-by: Joel Schopp <joel.schopp@amd.com>
Reported-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Jens Axboe [Tue, 16 Sep 2014 19:38:51 +0000 (13:38 -0600)]
genhd: fix leftover might_sleep() in blk_free_devt()
Commit
2da78092 changed the locking from a mutex to a spinlock,
so we now longer sleep in this context. But there was a leftover
might_sleep() in there, which now triggers since we do the final
free from an RCU callback. Get rid of it.
Reported-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
David S. Miller [Mon, 22 Sep 2014 20:41:41 +0000 (16:41 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2014-09-22
We generate a blackhole or queueing route if a packet
matches an IPsec policy but a state can't be resolved.
Here we assume that dst_output() is called to kill
these packets. Unfortunately this assumption is not
true in all cases, so it is possible that these packets
leave the system without the necessary transformations.
This pull request contains two patches to fix this issue:
1) Fix for blackhole routed packets.
2) Fix for queue routed packets.
Both patches are serious stable candidates.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Fri, 19 Sep 2014 14:16:25 +0000 (16:16 +0200)]
dm9000: Return an ERR_PTR() in all error conditions of dm9000_parse_dt()
In one error condition dm9000_parse_dt() returns NULL, however the
return value is checked using IS_ERR() in dm9000_probe(), leading to the
error not being properly propagated if CONFIG_OF is not enabled or the
device tree data is not available. Fix this by also returning an
ERR_PTR() in this case.
Fixes:
0b8bf1baabe5 (net: dm9000: Allow instantiation using device tree)
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wojciech Dubowik [Thu, 18 Sep 2014 06:30:41 +0000 (08:30 +0200)]
ath9k: Fix NULL pointer dereference on early irq
The ah struct might not have been initialized when
interrupt comes so check for it.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Loic Poulain [Tue, 16 Sep 2014 12:53:58 +0000 (14:53 +0200)]
net: rfkill: gpio: Fix clock status
Clock is disabled when the device is blocked.
So, clock_enabled is the logical negation of "blocked".
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 22 Sep 2014 19:57:46 +0000 (15:57 -0400)]
Merge tag 'nfc-fixes-3.17-1' of git://git./linux/kernel/git/sameo/nfc-fixes
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.17 fixes
We have 3 NFC fixes for 3.17:
- 2 potential build failures for ST21NFCA and ST21NFCB, triggered by a
depmod dependenyc cycle.
- One potential buffer overflow in the microread driver."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Fri, 19 Sep 2014 10:40:25 +0000 (13:40 +0300)]
r8169: fix an if condition
There is an extra semi-colon so __rtl8169_set_features() is called every
time.
Fixes:
929a031dfd62 ('r8169: adjust __rtl8169_set_features')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>--
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 22 Sep 2014 18:58:23 +0000 (11:58 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Two very simple bugfixes, affecting all supported architectures"
[ Two? There's three commits in here. Oh well, I guess Paolo didn't
count the preparatory symbol export ]
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: correct null pid check in kvm_vcpu_yield_to()
KVM: check for !is_zero_pfn() in kvm_is_mmio_pfn()
mm: export symbol dependencies of is_zero_pfn()
hayeswang [Fri, 19 Sep 2014 07:17:18 +0000 (15:17 +0800)]
r8152: disable ALDPS
If the hw is in ALDPS mode, the hw may have no response for accessing
the most registers. Therefore, the ALDPS should be disabled before
accessing the hw in rtl_ops.init(), rtl_ops.disable(), rtl_ops.up(),
and rtl_ops.down(). Regardless of rtl_ops.enable(), because the hw
wouldn't enter ALDPS mode when linking on. The hw would enter the
ALDPS mode after several seconds when link down occurs and the ALDPS
is enabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 18 Sep 2014 18:00:27 +0000 (11:00 -0700)]
ipoib: validate struct ipoib_cb size
To catch future errors sooner.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 18 Sep 2014 15:02:05 +0000 (08:02 -0700)]
net: sched: shrink struct qdisc_skb_cb to 28 bytes
We cannot make struct qdisc_skb_cb bigger without impacting IPoIB,
or increasing skb->cb[] size.
Commit
e0f31d849867 ("flow_keys: Record IP layer protocol in
skb_flow_dissect()") broke IPoIB.
Only current offender is sch_choke, and this one do not need an
absolutely precise flow key.
If we store 17 bytes of flow key, its more than enough. (Its the actual
size of flow_keys if it was a packed structure, but we might add new
fields at the end of it later)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes:
e0f31d849867 ("flow_keys: Record IP layer protocol in skb_flow_dissect()")
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Thu, 18 Sep 2014 14:31:17 +0000 (10:31 -0400)]
tg3: Work around HW/FW limitations with vlan encapsulated frames
TG3 appears to have an issue performing TSO and checksum offloading
correclty when the frame has been vlan encapsulated (non-accelrated).
In these cases, tcp checksum is not correctly updated.
This patch attempts to work around this issue. After the patch,
802.1ad vlans start working correctly over tg3 devices.
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sundarjdev [Mon, 22 Sep 2014 17:31:39 +0000 (10:31 -0700)]
hwmon: (tmp103) Fix resource leak bug in tmp103 temperature sensor driver
tmp103 temperature sensor driver registers with the hwmon framework by calling
hwmon_device_register_with_groups but does not have a .remove method to call
hwmon_device_unregister to unregister from the framework when the device is no
longer needed. Fix this by calling devm_hwmon_device_register_with_groups.
Signed-off-by: Sundar J Dev <sundarjayakumardev@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Nicolas Dichtel [Wed, 17 Sep 2014 08:08:08 +0000 (10:08 +0200)]
macvlan: allow to enqueue broadcast pkt on virtual device
Since commit
412ca1550cbe ("macvlan: Move broadcasts into a work queue"), the
driver uses tx_queue_len of the master device as the limit of packets enqueuing.
Problem is that virtual drivers have this value set to 0, thus all broadcast
packets were rejected.
Because tx_queue_len was arbitrarily chosen, I replace it with a static limit
of 1000 (also arbitrarily chosen).
CC: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: Thibaut Collet <thibaut.collet@6wind.com>
Suggested-by: Thibaut Collet <thibaut.collet@6wind.com>
Tested-by: Thibaut Collet <thibaut.collet@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jens Axboe [Fri, 19 Sep 2014 19:10:29 +0000 (13:10 -0600)]
blk-mq: use blk_mq_start_hw_queues() when running requeue work
When requests are retried due to hw or sw resource shortages,
we often stop the associated hardware queue. So ensure that we
restart the queues when running the requeue work, otherwise the
queue run will be a no-op.
Signed-off-by: Jens Axboe <axboe@fb.com>
Jens Axboe [Fri, 19 Sep 2014 14:04:53 +0000 (08:04 -0600)]
blk-mq: fix potential oops on out-of-memory in __blk_mq_alloc_rq_maps()
__blk_mq_alloc_rq_maps() can be invoked multiple times, if we scale
back the queue depth if we are low on memory. So don't clear
set->tags when we fail, this is handled directly in
the parent function, blk_mq_alloc_tag_set().
Reported-by: Robert Elliott <Elliott@hp.com>
Signed-off-by: Jens Axboe <axboe@fb.com>