drm/i915/dp: Add HBR3 rate (8.1 Gbps) to dp_rates array

dp_rates[] array is a superset of all the link rates supported
by sink devices. DP 1.3 specification adds HBR3 (8.1Gbps) link rate
to the set of link rates supported by sink. This patch adds this rate
to dp_rates[] array that gets used to populate the sink_rates[]
array limited by max rate obtained from DP_MAX_LINK_RATE DPCD register.

v2:
* Rebased on top of Jani's localized rates patch

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1519857110-26916-1-git-send-email-manasi.d.navare@intel.com

drm/i915/dp: move link rate arrays where they're used

Localize link rate arrays by moving them to the functions where they're
used. Further clarify the distinction between source and sink
capabilities. Split pre and post Haswell arrays, and get rid of the
array size arithmetics. Use a direct rate value in the paranoia case of
no common rates find.

Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227105911.4485-1-jani.nikula@intel.com

drm/i915: Consult aux_ch instead of port in ->get_aux_clock_divider()

While it seems totally unlikely that any system would mix a cpu/north
aux channel with a pch/south port (or vice versa) we should still
consult intel_dp->aux_ch rather than encoder->port when figuring out
which clock is actually used by the aux ch.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-5-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #irc

drm/i915: Don't deref request->ctx inside unlocked print_request()

Although we protect the request itself, we don't lock inside
intel_engine_dump() and so the request maybe retired as we peek into it.
One consequence is that the request->ctx may be freed before we
dereference it, leading to a use-after-free. Replace the hw_id we are
peeking from inside request->ctx with the request->fence.context, with
which we can still track from which context the request originated
(although to tie to HW reports requires a little more legwork, but is
good enough to follow the GEM traces).

[52640.729670] general protection fault: 0000 [#2] SMP
[52640.729694] Dumping ftrace buffer:
[52640.729701]    (ftrace buffer empty)
[52640.729705] Modules linked in: vgem snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic x86_pkg_\
temp_thermal intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul snd_hda_intel snd_hda_codec snd_hwdep gha\
sh_clmulni_intel snd_hda_core snd_pcm mei_me mei i915 r8169 mii prime_numbers i2c_hid
[52640.729748] CPU: 2 PID: 4335 Comm: gem_exec_schedu Tainted: G     UD W        4.16.0-rc3+ #7
[52640.729759] Hardware name: Acer Aspire E5-575G/Ironman_SK  , BIOS V1.12 08/02/2016
[52640.729803] RIP: 0010:print_request+0x2b/0xb0 [i915]
[52640.729811] RSP: 0018:ffffc90001453c18 EFLAGS: 00010206
[52640.729820] RAX: 6b6b6b6b6b6b6b6b RBX: ffff8801e0292d40 RCX: 0000000000000006
[52640.729829] RDX: ffffc90001453c60 RSI: ffff8801e0292d40 RDI: 0000000000000003
[52640.729838] RBP: ffffc90001453d80 R08: 0000000000000000 R09: 0000000000000001
[52640.729847] R10: ffffc90001453bd0 R11: ffffc90001453c73 R12: ffffc90001453c60
[52640.729856] R13: ffffc90001453d80 R14: ffff8801d5a683c8 R15: ffff8801e0292d40
[52640.729866] FS:  00007f1ee50548c0(0000) GS:ffff8801e8200000(0000) knlGS:0000000000000000
[52640.729876] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[52640.729884] CR2: 00007f1ee5077000 CR3: 00000001d9411004 CR4: 00000000003606e0
[52640.729893] Call Trace:
[52640.729922]  intel_engine_print_registers+0x623/0x890 [i915]
[52640.729948]  intel_engine_dump+0x4a3/0x590 [i915]
[52640.729957]  ? seq_printf+0x3a/0x50
[52640.729977]  i915_engine_info+0xb8/0xe0 [i915]
[52640.729984]  ? drm_mode_gamma_get_ioctl+0xf0/0xf0
[52640.729990]  seq_read+0xd5/0x410
[52640.729997]  full_proxy_read+0x4b/0x70
[52640.730004]  __vfs_read+0x1e/0x120
[52640.730009]  ? do_sys_open+0x134/0x220
[52640.730015]  ? kmem_cache_free+0x174/0x2b0
[52640.730021]  vfs_read+0xa1/0x150
[52640.730026]  SyS_read+0x40/0xa0
[52640.730032]  do_syscall_64+0x65/0x1a0
[52640.730038]  entry_SYSCALL_64_after_hwframe+0x42/0xb7

Reported-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180228094732.28462-1-chris@chris-wilson.co.uk

drm/i915: Don't mangle the CTM on pre-HSW

On pre-HSW we have dedicated hardware for the RGB limited range
handling, and so we don't want to compress with the CSC matrix.

Toss in a FIXME about gamma LUT vs. limited range using the CSC.

Cc: Johnson Lin <johnson.lin@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222214232.6064-4-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>

drm/i915: Rename pipe CSC to use ilk_ prefix

The pipe CSC was introduced by ILK, so change everything related
to use ilk_ as the prefix.

Cc: Johnson Lin <johnson.lin@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222214232.6064-3-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>

drm/i915: Remove the pointless 1:1 matrix copy

If we don't have to frob with the user provided ctm matrix there's
no point in copying it over. Just point at the user ctm directly.

Also the matrix gets fully populated by ctm_mult_by_limited() so
no need to zero initialize it.

Cc: Johnson Lin <johnson.lin@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222214232.6064-2-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>

Merge drm-next into drm-intel-next-queued

To pull in the HDCP changes, especially wait_for changes to drm/i915
that Chris wants to build on top of.

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Enable VBT based BL control for DP

Currently, BXT_PP is hardcoded with value '0'.
It practically disabled eDP backlight on MRB (BXT) platform.

This patch will tell which BXT_PP registers (there are two set of
PP_CONTROL in the spec) to be used as defined in VBT (Video Bios Timing
table) and this will enabled eDP backlight controller on MRB (BXT)
platform.

v2:
 - Remove unnecessary information in commit message.
 - Assign vbt.backlight.controller to a backlight_controller variable and
   return the variable value.
v3:
 - Rebased to latest code base.
 - updated commit title.

Signed-off-by: Mustamin B Mustaffa <mustamin.b.mustaffa@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227030734.37901-1-mustamin.b.mustaffa@intel.com

drm/i915: Repeat the GEM_BUG_ON message in the ftrace log

As the ftrace log is overflowing the pstore capture, we lose the last
gasps from dmesg which includes the GEM_BUG_ON function:line and condition
that failed. Vital information for tracking down the bug, so append it to
the frace log as well.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227211816.5546-1-chris@chris-wilson.co.uk

drm/i915/cnl: Add WaRsDisableCoarsePowerGating

Old Wa added now forever on CNL all steppings.

With CPU P states enabled along with RC6, dispatcher
hangs can happen.

Cc: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222200535.9290-1-rodrigo.vivi@intel.com

drm/i915/psr: Don't avoid PSR when PSR2 conditions are not met.

We can still use PSR1 when PSR2 conditions are not met.

So, let's split the check in a way that we make sure has_psr
gets set independently of PSR2 criteria.

v2: Duh! Handle proper return to avoid breaking PSR2.
v3: (DK):
- better name for psr2 conditions check function
- Don't remove FIXME block and psr2.support check.
- Add a debug message to show us what PSR or PSR2 is
  getting enabled now we have ways to enabled PSR on
  PSR2 panels.
- s/PSR2 disabled/PSR2 not enabled

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227212913.14083-2-rodrigo.vivi@intel.com

drm/i915/psr2: Fix max resolution supported.

According to spec:
"PSR2 is supported for pipe active sizes up to
3640 pixels wide and 2304 lines tall."

BSpec: 7713

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227212913.14083-1-rodrigo.vivi@intel.com

drm/i915/psr: Check for power state control capability.

eDP spec says - "If PSR/PSR2 is supported, the SET_POWER_CAPABLE bit in the
EDP_GENERAL_CAPABILITY_1 register (DPCD Address 00701h, bit d7) must be set
to 1."

Reject PSR on panels without this cap bit set as such panels cannot be
controlled via SET_POWER & SET_DP_PWR_VOLTAGE register and the DP source
needs to be able to do that for PSR.

Thanks to Nathan for debugging this.

Panel cap checks like this can be done just once, let's fix this
when PSR dpcd init movement lands.

Cc: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Tested-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227032723.15474-1-dhinakaran.pandiyan@intel.com

drm/i915/dp: Move comment about hw timeout to the right place.

No functional change.

Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223221520.18464-6-dhinakaran.pandiyan@intel.com

drm/i915/dp: Remove redundant sleep after AUX transaction length check.

The core already takes care of the delay before retrying. The delay now
changes to (500, 600)us instead of (500 + 1000, 600 + 1500)us.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223221520.18464-5-dhinakaran.pandiyan@intel.com

drm/i915/psr: Check for the specific AUX_FRAME_SYNC cap bit.

The cap check should be specifically for bit 0 instead of any bit.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Fixes: 474d1ec4a3d7 ("drm/i915/skl: Enabling PSR2 SU with frame sync")
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223221520.18464-4-dhinakaran.pandiyan@intel.com

drm/i915/psr: Extract PSR DPCD initialization and move it to intel_psr.c

intel_edp_init_dpcd() is cluttered with PSR specific DPCD checks and
intel_dp.c is huge.

No functional change intended.

v2: Rebased.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223221520.18464-3-dhinakaran.pandiyan@intel.com

drm/i915/frontbuffer: Mark frontbuffer flush and invalidate with might_sleep()

Frontbuffer flush and invalidate call psr, fbc and drrs functions that use
mutexes but they can be called in atomic contexts in the fbdev path. The
point where the spinlocks are acquired is up in the call stack that is not
entirely easy to spot, so annotate with might_sleep().

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223221520.18464-2-dhinakaran.pandiyan@intel.com

drm/i915/psr: New power domain for AUX IO.

PSR on CNL requires AUX IO wells to be kept on and the existing AUX domain
for AUX-A enables DC_OFF well too. This is not required, so add a new
AUX_IO_A domain for AUX-A to allow DC states to remain enabled. Other AUX
channels re-use the existing AUX domains.

v4: Reword comment (Rodrigo and Ville)
    Rename _get and _put functions to include aux_io substring(Rodrigo)
    Remove unnecessary diff that got included.
v3: Extract aux domain selection into a function (Ville)
v2: Add AUX IO domain only for AUX-A
    Rebased on top of Ville's AUX series.

Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223221520.18464-1-dhinakaran.pandiyan@intel.com

drm/i915/guc: Fill preempt context once at init time

Since we're inhibiting context save of preempt context, we're no longer
tracking the position of HEAD/TAIL. With GuC, we're adding a new
breadcrumb for each preemption, which means that the HW will do more and
more breadcrumb writes. Eventually the ring is filled, and we're
submitting the preemption context with HEAD==TAIL==0, which won't result
in breadcrumb write, but will trigger hangcheck instead.
Instead of writing a new preempt breadcrumb for each preemption, let's
just fill the ring once at init time (which also saves a couple of
instructions in the tasklet).

v2: Assert that context save restore is inhibited, don't assert on ring
    alignment. (Chris)
v3: Cleanup checkpatch.

Fixes: 517aaffe0c1b ("drm/i915/execlists: Inhibit context save/restore for the fake preempt context")
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180226163800.21745-1-michal.winiarski@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/dp: Fix the order of platforms for setting DP source rates

The usual if ladder order should be from newest to oldest
platform. However the CNL conditional statement was misplaced.
This patch sets the DP source for platforms starting from the newest
to oldest.

Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1519701075-9894-1-git-send-email-manasi.d.navare@intel.com

drm/i915/preemption: Allow preemption between submission ports

Sometimes we need to boost the priority of an in-flight request, which
may lead to the situation where the second submission port then contains
a higher priority context than the first and so we need to inject a
preemption event. To do so we must always check inside
execlists_dequeue() whether there is a priority inversion between the
ports themselves as well as the head of the priority sorted queue, and we
cannot just skip dequeuing if the queue is empty.

As Michał noted, this doesn't simply extend to handling more than 2-port
submission, as we may need to reorder within the array of executing
requests which themselves are lower priority than the first. A task for
later!

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222142229.14517-1-chris@chris-wilson.co.uk
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>

drm/i915: Update missing parts after the rename to i915_request

Mostly doc/print messages that were not updated after commit e61e0f51ba79
("drm/i915: Rename drm_i915_gem_request to i915_request").

Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222172405.11386-1-michel.thierry@intel.com

drm/i915: Collect aux ch vfunc setup into intel_dp_aux_init()

Collect all the aux ch vfunc assignments into intel_dp_aux_init()
instead of having it spread around.

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-4-ville.syrjala@linux.intel.com

drm/i915: Nuke aux regs from intel_dp

Just store function pointers that give us the correct register offsets
instead of storing the register offsets themselves. Slightly less
efficient perhaps but saves a few bytes and better matches how we do
things elsewhere.

v2: Keep a local array of data registers (Chris)

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-3-ville.syrjala@linux.intel.com

drm/i915: Add enum aux_ch and clean up the aux init to use it

Since we no longer have a 1:1 correspondence between ports and AUX
channels, let's give AUX channels their own enum. Makes it easier
to tell the apples from the oranges, and we get rid of the
port E AUX power domain FIXME since we now derive the power domain
from the actual AUX CH.

v2: Rebase due to AUX F
v3: Split out the power domain fix (Rodrigo)

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> #v2
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-2-ville.syrjala@linux.intel.com

drm/i915: Use the correct power domain for aux ch

Select the aux power domain based on the aux ch rather than based on
the port. Now we can rid ourselves of the port E FIXME as well.

v2: Split from the enum aux_ch patch (Rodrigo)

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> #v1
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-1-ville.syrjala@linux.intel.com

drm/i915: Add a FIXME about FBC vs. fence. 90/270 degree rotation

Currently the FBC code doesn't handle the 90/270 degree rotated case
correctly. We would need the GTT tracking to monitor the fence on the
normal GTT view (the rotated view doesn't even have a fence). Not quite
sure how we should program the fence Y offset etc. in that case. For now
we'll end up disabling FBC with 90/270 degree rotation. Add a FIXME
to remind people about this fact.

v2: Reword the text (Chris)
    Move the FIXME to the fbc code

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221160235.11134-7-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Extract intel_plane_{pin,unpin}_fb()

We've replicated the fb pin/unpin code in a few places. Pull it into
convenint helpers.

Slight change in locking behaviour as intel_cleanup_plane_fb() now
grab struct_mutex unconditionally.

v2: Change the locking to be symmetric between pin and unpin

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221160235.11134-6-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Require fence only for FBC capable planes

As only a subset of primary planes are FBC capable there's no need
to waste fences on all of them. So let's skip the fence if the plane
isn't even fbc capable.

In the future we might extend this to skip the fence even for FBC
capable planes if the crtc and/or plane state isn't suitable
for FBC.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221160235.11134-5-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Clean up fbc vs. plane checks

Let's record the information whether a plane can do fbc or not under
struct inte_plane.

v2: Rebase due to i9xx_plane_id
    Handle BDW/HSW correctly
v3: Move inte_fbc_init() back since we depend on it happening
    even with i915.disable_display, and populate
    fbc->possible_framebuffer_bits directly from the
    plane init code instead
v4: Add note about plane A being tied to pipe A on HSW+

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221173101.19385-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221160235.11134-5-ville.syrjala@linux.intel.com

drm/i915: Only pin the fence for primary planes (and gen2/3)

Currently we pin a fence on every plane doing tiled scanout. The
number of planes we have available is fast apporaching the number
of fences so we really should stop wasting them. Only FBC needs
the fence on gen4+, so let's use fences only for the primary planes
on those platforms.

v2: drop the tiling check from plane_uses_fence() as the obj is
    NULL during initial_plane_config() and we don't rally need the
    check since i915_vma_pin_fence() does the check anyway

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221184807.577-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Fail if we can't get a fence for gen2/3 tiled scanout

Gen2/3 display engine depends on the fence for tiled scanout. So if we
fail to get a fence fail the entire operation.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221160235.11134-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Fix Limited Range Color Handling

Some panels support limited range output (16-235) compared
to full range RGB values (0-255). Also userspace can control
the RGB range using "Broadcast RGB" property. Currently the
code to handle full range to limited range is broken. This
patch fixes the same by properly scaling down all the full
range co-efficients with limited range scaling factor.

v2: Fixed Ville's review comments.

v3: Changed input to const and used correct data types as
    suggested by Ville

v4: Fixed some missing data type corrections.

Signed-off-by: Johnson Lin <johnson.lin@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1517327489-26128-1-git-send-email-uma.shankar@intel.com

drm/i915: Move page sizes out of the 8-bit sandwich

Slightly smaller code and a bit more logical layout.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222111658.4999-1-tvrtko.ursulin@linux.intel.com

drm/i915/hsw: add missing disabled EUs registers reads

It turns out that HSW has a register that tells us how many EUs are
disabled per half-slice (roughly a similar notion to subslice). We
didn't read those registers so far as most userspace drivers didn't
need those values prior to Gen8, but an internal library would like to
have access to this.

Since we already have the getparam interface, there is no harm in
exposing this.

v2: Rename bits value (Joonas)

v3: s/GEM_BUG_ON/MISSING_CASE/ (Joonas)

v4: s/GEM_BUG_ON/MISSING_CASE/ again... (Lionel)

Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221204902.23084-1-lionel.g.landwerlin@intel.com

drm/i915/icl: Show interrupt registers in debugfs

Show GEN11 specific interrupt registers in debugfs

v2: Update for POR changes. (Daniele Ceraolo Spurio)
v3: get runtime pm ref. unify common parts with gen8 (Daniele)

Cc: Ceraolo Spurio, Daniele <daniele.ceraolospurio@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220153755.13509-2-mika.kuoppala@linux.intel.com

drm/i915/icl: Add the ICL PCI IDs

This is the current PCI ID list in our documentation.

Let's leave the _gt#_ part out for now since our current documentation
is not 100% clear and we don't need this info now anyway.

v2: Use the new ICL_11 naming (Kelvin Gardiner).
v3: Latest IDs as per BSpec (Oscar).
v4: Make it compile (Paulo).
v5: Remove comments (Lucas).
v6: Multile rebases (Paulo).
v7: Rebase (Mika)

Reviewed-by: Anuj Phogat <anuj.phogat@intel.com> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220153755.13509-1-mika.kuoppala@linux.intel.com

drm/i915/execlists: Move the GEM_BUG_ON context matches CSB later

Print out the current request/context before doing the GEM_BUG_ON, so
that we can inspect the values in the ftrace.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221152301.9178-1-chris@chris-wilson.co.uk

drm/i915/execlists: Add a GEM_TRACE to show when the context is completed

Include a GEM_TRACE to show when the context is complete and we advance
the ELSP port.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221151553.9054-1-chris@chris-wilson.co.uk

drm/i915/execlists: Remove the ring advancement under preemption

Load an empty ringbuffer for preemption, ignoring the lite-restore
workaround as we know the preempt context is always idle before preemption.

Note that after some digging by Michal Winiarski, we found that
RING_HEAD is no longer being updated (due to inhibiting context save
restore) so this patch is already in effect!

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221133236.29402-1-chris@chris-wilson.co.uk

drm/i915: Rename drm_i915_gem_request to i915_request

We want to de-emphasize the link between the request (dependency,
execution and fence tracking) from GEM and so rename the struct from
drm_i915_gem_request to i915_request. That is we may implement the GEM
user interface on top of requests, but they are an abstraction for
tracking execution rather than an implementation detail of GEM. (Since
they are not tied to HW, we keep the i915 prefix as opposed to intel.)

In short, the spatch:
@@

@@
- struct drm_i915_gem_request
+ struct i915_request

A corollary to contracting the type name, we also harmonise on using
'rq' shorthand for local variables where space if of the essence and
repetition makes 'request' unwieldy. For globals and struct members,
'request' is still much preferred for its clarity.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221095636.6649-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/doc: Fix documentation for _vblank_restore().

No code changes, fixes doc build warnings and polish some doc text.

Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221073908.4500-1-dhinakaran.pandiyan@intel.com

drm/todo: i915 could use device_link_add

Noticed while reading some unrelated patches. Unfortunately Imre's
patch to add our early/late hooks predated the device_link
infrastructure by 2 years.

Cc: Imre Deak <imre.deak@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220132017.30719-1-daniel.vetter@ffwll.ch

drm/i915: Make global seqno known in i915_gem_request_execute tracepoint

Commit fe49789fab97 ("drm/i915: Deconstruct execute fence") re-arranged
the code and moved the i915_gem_request_execute tracepoint to before the
global seqno is assigned to the request.

We need to move the tracepoint a bit later so this information is once
again available.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: fe49789fab97 ("drm/i915: Deconstruct execute fence")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220104742.565-1-tvrtko.ursulin@linux.intel.com

drm/i915: Update DRIVER_DATE to 20180221

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915/fbc: Use PLANE_HAS_FENCE to determine if the plane is fenced

Rather than trusting the cached value of plane_state->vma->fence to
imply whether the plane_state itself holds a reference on the
framebuffer's fence, use the information provided in the
plane_state->flags (PLANE_HAS_FENCE). Note that we still assume that FBC
is entirely bounded by the plane_state active life span; it's not clear
if that is a safe assumption.

Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220134208.24988-4-chris@chris-wilson.co.uk

drm/i915/fbdev: Use the PLANE_HAS_FENCE flags from the time of pinning

Use the information about the fence state from the time of pinning to
determine if the fbdev writes are going through a fence. This avoids any
confusion in cases where the fence may appear or disappear unconnected
to the use by fbdev.

Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220134208.24988-3-chris@chris-wilson.co.uk

drm/i915: Move the policy for placement of the GGTT vma into the caller

Currently we make the unilateral decision inside
i915_gem_object_pin_to_display() where the VMA should resided (inside
the fence and mappable region or above?). This is not our decision to
make as it impacts on how the display engine can use the resulting
scanout object, and it would rather instruct us where to place the VMA so
that it can enable the features it wants. As such, make the pin flags an
argument to i915_gem_object_pin_to_display() and control them from
intel_pin_and_fence_fb_obj()

Whilst taking control of the mapping for ourselves, start tracking how
we use it to avoid trying to free a fence we never claimed:

<3>[  227.151869] GEM_BUG_ON(vma->fence->pin_count <= 0)
<4>[  227.152064] ------------[ cut here ]------------
<2>[  227.152068] kernel BUG at drivers/gpu/drm/i915/i915_vma.h:391!
<4>[  227.152084] invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
<0>[  227.152092] Dumping ftrace buffer:
<0>[  227.152099]    (ftrace buffer empty)
<4>[  227.152102] Modules linked in: i915 snd_hda_codec_analog snd_hda_codec_generic coretemp snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm lpc_ich e1000e mei_me mei prime_numbers
<4>[  227.152131] CPU: 1 PID: 1587 Comm: kworker/u16:49 Tainted: G     U           4.16.0-rc1-gbab67b2f6177-kasan_7+ #1
<4>[  227.152134] Hardware name: Dell Inc. OptiPlex 755                 /0PU052, BIOS A08 02/19/2008
<4>[  227.152236] Workqueue: events_unbound intel_atomic_commit_work [i915]
<4>[  227.152292] RIP: 0010:intel_unpin_fb_vma+0x23a/0x2a0 [i915]
<4>[  227.152295] RSP: 0018:ffff88005aad7b68 EFLAGS: 00010286
<4>[  227.152300] RAX: 0000000000000026 RBX: ffff88005c359580 RCX: 0000000000000000
<4>[  227.152304] RDX: 0000000000000026 RSI: ffffffff8707d840 RDI: ffffed000b55af63
<4>[  227.152307] RBP: ffff880056817e58 R08: 0000000000000001 R09: 0000000000000000
<4>[  227.152311] R10: ffff88005aad7b88 R11: 0000000000000000 R12: ffff8800568184d0
<4>[  227.152314] R13: ffff880065b5ab08 R14: 0000000000000000 R15: dffffc0000000000
<4>[  227.152318] FS:  0000000000000000(0000) GS:ffff88006ac40000(0000) knlGS:0000000000000000
<4>[  227.152322] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4>[  227.152325] CR2: 00007f5fb25550a8 CR3: 0000000068c78000 CR4: 00000000000006e0
<4>[  227.152328] Call Trace:
<4>[  227.152385]  intel_cleanup_plane_fb+0x6b/0xd0 [i915]
<4>[  227.152395]  drm_atomic_helper_cleanup_planes+0x166/0x280
<4>[  227.152452]  intel_atomic_commit_tail+0x159d/0x3380 [i915]
<4>[  227.152463]  ? process_one_work+0x66e/0x1460
<4>[  227.152516]  ? skl_update_crtcs+0x9c0/0x9c0 [i915]
<4>[  227.152523]  ? lock_acquire+0x13d/0x390
<4>[  227.152527]  ? lock_acquire+0x13d/0x390
<4>[  227.152534]  process_one_work+0x71a/0x1460
<4>[  227.152540]  ? __schedule+0x815/0x1e20
<4>[  227.152547]  ? pwq_dec_nr_in_flight+0x2b0/0x2b0
<4>[  227.152553]  ? _raw_spin_lock_irq+0xa/0x40
<4>[  227.152559]  worker_thread+0xdf/0xf60
<4>[  227.152569]  ? process_one_work+0x1460/0x1460
<4>[  227.152573]  kthread+0x2cf/0x3c0
<4>[  227.152578]  ? _kthread_create_on_node+0xa0/0xa0
<4>[  227.152583]  ret_from_fork+0x3a/0x50
<4>[  227.152591] Code: c6 00 11 86 c0 48 c7 c7 e0 bd 85 c0 e8 60 e7 a9 c4 0f ff e9 1f fe ff ff 48 c7 c6 40 10 86 c0 48 c7 c7 e0 ca 85 c0 e8 2b 95 bd c4 <0f> 0b 48 89 ef e8 4c 44 e8 c4 e9 ef fd ff ff e8 42 44 e8 c4 e9
<1>[  227.152720] RIP: intel_unpin_fb_vma+0x23a/0x2a0 [i915] RSP: ffff88005aad7b68

v2: i915_vma_pin_fence() is a no-op if a fence isn't required, so check
vma->fence as well.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220134208.24988-2-chris@chris-wilson.co.uk

drm/i915: Also check view->type for a normal GGTT view

We cannot simply use !view as shorthand for all normal GGTT views as a
few callers will always populate a i915_ggtt_view struct and set the
type to NORMAL instead. So check for (!view || view->type == NORMAL)
inside i915_gem_object_ggtt_pin().

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220134208.24988-1-chris@chris-wilson.co.uk

drm/i915: Drop WaDoubleCursorLP3Latency:ivb

WaDoubleCursorLP3Latency was meant for pre-production hardware.
Drop it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130203807.13721-6-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>

drm/i915: Set the primary plane pipe select bits on gen4

i965 and g4x still have the pipe select bits in the plane control
registers, they're just hardcoded to select a specific pipe. However
plane C on i965 can still move between the pipes, thus we should
program the pipe select bits on i965 if we want to expose plane C
some day.

Since there is no harm in programming the bits on any plane on
i965/g4x let's just always set them. This will also make our
pre-computed register value match what the hardware register
would read, should we want to cross check the two.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130203807.13721-2-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>

drm/i915: Don't set cursor pipe select bits on g4x+

G4x cursor control registers still allow us to write to the pipe select
bits even though cursors are supposed to be fixed to a specific pipe.
Bspec tells us that we should only ever write 0 to these bits. Let's
follow that recommendation. On ilk+ the bits become hardwired to 0.

Also looks like ICL repurposes these bits for some other use, so
we had better stop setting them to bogus values there.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130203807.13721-1-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>

drm/i915: Assert that we don't overflow frontbuffer tracking bits

Add some compile time assrts to the frontbuffer tracking to make sure
that we have enough bits per pipe to cover all the planes, and that we
have enough total bits to cover all the planes across all pipes.

We'll ignore any potential clash between the overlay bit and the
plane bits because that will allow us to keep using a total of 32
bits for the foreseeable future.

While at it change the macros to use BIT() and GENMASK(). The latter
gets rid of the hardcoded 0xff and thus means we can change the
number of bits per pipe by just changing
INTEL_FRONTBUFFER_BITS_PER_PIPE.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180124183642.32549-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Track number of pending freed objects

During igt, we frequently call into the driver to reset both HW and
driver state (idling the device, waiting for it to become idle and
freeing off old objects) to ensure that we start each test/subtest/pass
from known state. This process incurs an RCU barrier or two to ensure
that any such pending frees are indeed flushed before we return.
However, unconditionally waiting on the RCU barrier adds needless delay
to many callers, which adds up to several seconds when repeated thousands
of times. We can skip the rcu_barrier() if by tracking how many outstanding
frees we have, we know there are none.

The same path is used along suspend, where we may be able to save the
unconditional RCU barrier.

To put it into perspective with a completely meaningless
microbenchmark, igt/gem_sync/idle is improved from 50ms to 30us on bdw.

v2: Remove the extra synchronize_rcu() inside i915_drop_caches_set()

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180219220631.25001-1-chris@chris-wilson.co.uk

drm/i915/: Initialise trans_min for skl_compute_transition_wm()

clang spots

drivers/gpu/drm/i915/intel_pm.c:4655:6: warning: variable 'trans_min' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
        if (INTEL_GEN(dev_priv) >= 10)

but fortunately for us we skip the function unless on a gen10+ device.
However, to keep the function generic in case we do want to re-enable it
for gen9 again, initialise trans_min to 0.

References: ca47667f523e ("drm/i915/gen10: Calculate and enable transition WM")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115105036.1094-3-chris@chris-wilson.co.uk
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915: Clear the in-use marker on execbuf failure

If we fail to unbind the vma (due to a signal on an active buffer that
needs to be moved for the next execbuf), then we need to clear the
persistent tracking state we setup for this execbuf.

Fixes: c7c6e46f913b ("drm/i915: Convert execbuf to use struct-of-array packing for critical fields")
Testcase: igt/gem_fenced_exec_thrash/no-spare-fences-busy*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.14+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180219140144.24004-1-chris@chris-wilson.co.uk

drm/i915: Prune gen8_gt_irq_handler

The compiler is not automatically caching the i915->regs address inside
a register and emitting a load for every mmio access. For simple
functions like gen8_gt_irq_handler that are already using the raw
accessors, we can open-code them for substantial savings:

add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-83 (-83)
Function                                     old     new   delta
gen8_gt_irq_handler                          290     266     -24
gen8_gt_irq_ack                              181     122     -59
Total: Before=954637, After=954554, chg -0.01%

v2: Add raw_reg_read/raw_reg_write.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180219100926.16554-1-chris@chris-wilson.co.uk

drm/i915: Track GT interrupt handling using the master iir

Keep the master iir and use it to reduce the number of reads and writes
to the GT iir array, i.e. only the bits marked as set by the master iir
are valid inside GT iir array and will be handled during the interrupt.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215073713.26985-1-chris@chris-wilson.co.uk

drm/i915: Remove WARN_ONCE for failing to pm_runtime_if_in_use

As the driver is called to handle circumstances beyond it's control, we
cannot assume that the pm_runtime core is happy to see us. For example,
if we are called from shrink_slab to free up our pages during suspend,
rpm may be disabled and pm_runtime_if_in_use() decides to fail with
-EINVAL rather than simply say no. This is expected to happen, so don't
warn.  For example,

[  217.429228] Suspending console(s) (use no_console_suspend to debug)
[  217.557179] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[  217.559399] sd 0:0:0:0: [sda] Stopping disk
[  218.661567] i915 0000:00:02.0: Resetting chip after gpu hang
[  219.523879] ------------[ cut here ]------------
[  219.524474] pm_runtime_get_if_in_use() failed: -22
[  219.524817] WARNING: CPU: 1 PID: 14 at drivers/gpu/drm/i915/intel_runtime_pm.c:3351 intel_runtime_pm_get_if_in_use+0xe3/0x150 [i915]
[  219.524836] Modules linked in: vgem i915 snd_hda_codec_realtek snd_hda_codec_generic coretemp snd_hda_intel snd_hda_codec r8169 lpc_ich snd_hwdep mii snd_hda_core snd_pcm prime_numbers
[  219.525054] CPU: 1 PID: 14 Comm: cpuhp/1 Tainted: G     U           4.16.0-rc1-g740f57c54ecf-kasan_6+ #1
[  219.525070] Hardware name:  /D510MO, BIOS MOPNV10J.86A.0311.2010.0802.2346 08/02/2010
[  219.525294] RIP: 0010:intel_runtime_pm_get_if_in_use+0xe3/0x150 [i915]
[  219.525313] RSP: 0018:ffff880018f5edf8 EFLAGS: 00010286
[  219.525344] RAX: dffffc0000000008 RBX: ffff880007fc0000 RCX: 0000000000000000
[  219.525361] RDX: 0000000000000001 RSI: ffffffff850609c0 RDI: ffffffff872992a0
[  219.525377] RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
[  219.525394] R10: 0000000000000000 R11: 0000000000000000 R12: ffff880007fc0000
[  219.525411] R13: ffff880018f5f0f8 R14: ffff880007fc8de8 R15: ffff880018f5f0f0
[  219.525429] FS:  0000000000000000(0000) GS:ffff880019c80000(0000) knlGS:0000000000000000
[  219.525446] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  219.525463] CR2: 0000564df7897e86 CR3: 0000000000d7c000 CR4: 00000000000006e0
[  219.525478] Call Trace:
[  219.525734]  i915_gem_shrink+0x841/0xb50 [i915]
[  219.525802]  ? debug_check_no_locks_freed+0x2a0/0x2a0
[  219.525842]  ? trace_hardirqs_on_thunk+0x1a/0x1c
[  219.526083]  ? i915_gem_shrinker_count+0x2f0/0x2f0 [i915]
[  219.526131]  ? lock_acquire+0x138/0x3c0
[  219.526157]  ? lock_acquire+0x138/0x3c0
[  219.526391]  ? shrinker_lock+0x49/0x210 [i915]
[  219.526465]  ? mutex_trylock+0x15c/0x1a0
[  219.526694]  ? shrinker_lock+0x49/0x210 [i915]
[  219.526969]  ? i915_gem_shrinker_scan+0xc4/0x320 [i915]
[  219.527200]  i915_gem_shrinker_scan+0xc4/0x320 [i915]
[  219.527448]  ? i915_gem_shrinker_vmap+0x3a0/0x3a0 [i915]
[  219.527533]  shrink_slab.part.18+0x2d0/0x8d0
[  219.527613]  ? unregister_shrinker+0x1f0/0x1f0
[  219.527668]  ? mem_cgroup_iter+0x37d/0xc50
[  219.527728]  shrink_node+0x882/0xbe0
[  219.527847]  ? shrink_node_memcg+0x11c0/0x11c0
[  219.527882]  ? mark_held_locks+0xa8/0xf0
[  219.527931]  ? trace_hardirqs_on_caller+0x33f/0x590
[  219.527961]  ? ktime_get+0xad/0x140
[  219.528015]  do_try_to_free_pages+0x2d3/0xd70
[  219.528099]  ? allow_direct_reclaim.part.23+0x1d0/0x1d0
[  219.528132]  ? shrink_node+0xbe0/0xbe0
[  219.528213]  try_to_free_pages+0x1cd/0x570
[  219.528257]  ? do_try_to_free_pages+0xd70/0xd70
[  219.528355]  __alloc_pages_nodemask+0xadf/0x2110
[  219.528423]  ? unwind_next_frame+0x870/0x1970
[  219.528465]  ? deref_stack_reg+0x97/0xc0
[  219.528503]  ? gfp_pfmemalloc_allowed+0x150/0x150
[  219.528539]  ? register_sched_domain_sysctl+0x23a/0x1b90
[  219.528588]  ? unwind_next_frame+0x138/0x1970
[  219.528619]  ? kthread+0x30a/0x3d0
[  219.528677]  ? __read_once_size_nocheck.constprop.4+0x10/0x10
[  219.528698]  ? deref_stack_reg+0xc0/0xc0
[  219.528762]  ? __save_stack_trace+0x6e/0xd0
[  219.528822]  depot_save_stack+0x3bc/0x430
[  219.528870]  kasan_kmalloc+0x142/0x170
[  219.528912]  ? __kmalloc+0xf7/0x340
[  219.528935]  ? register_sched_domain_sysctl+0x23a/0x1b90
[  219.528957]  ? partition_sched_domains+0x4d4/0x840
[  219.528978]  ? sched_cpu_deactivate+0x11b/0x150
[  219.529001]  ? cpuhp_invoke_callback+0x160/0x15f0
[  219.529023]  ? cpuhp_thread_fun+0x35e/0x710
[  219.529044]  ? smpboot_thread_fn+0x50a/0x7f0
[  219.529065]  ? kthread+0x30a/0x3d0
[  219.529086]  ? ret_from_fork+0x24/0x50
[  219.529141]  ? register_sched_domain_sysctl+0x23a/0x1b90
[  219.529169]  ? register_sched_domain_sysctl+0x23a/0x1b90
[  219.529198]  ? set_track+0x87/0x100
[  219.529225]  ? init_object+0x6e/0x80
[  219.529275]  ? ___slab_alloc.constprop.36+0x232/0x3e0
[  219.529303]  ? ___slab_alloc.constprop.36+0x232/0x3e0
[  219.529325]  ? register_sched_domain_sysctl+0x23a/0x1b90
[  219.529410]  ? mark_held_locks+0xa8/0xf0
[  219.529453]  ? register_sched_domain_sysctl+0x23a/0x1b90
[  219.529479]  ? trace_hardirqs_on_caller+0x33f/0x590
[  219.529532]  __kmalloc+0xf7/0x340
[  219.529557]  ? register_sched_domain_sysctl+0x23a/0x1b90
[  219.529604]  register_sched_domain_sysctl+0x23a/0x1b90
[  219.529684]  ? sched_debug_show+0x20/0x20
[  219.529713]  ? debug_object_activate+0x530/0x530
[  219.529771]  ? rcu_lockdep_current_cpu_online+0xdc/0x130
[  219.529802]  ? partition_sched_domains+0x4ae/0x840
[  219.529825]  ? rcu_read_lock_sched_held+0x10f/0x130
[  219.529875]  partition_sched_domains+0x4d4/0x840
[  219.529955]  ? sched_init_domains+0x110/0x110
[  219.529981]  ? __wait_rcu_gp+0x24f/0x390
[  219.530054]  sched_cpu_deactivate+0x11b/0x150
[  219.530086]  ? sched_cpu_activate+0x1e0/0x1e0
[  219.530112]  ? __call_rcu.constprop.53+0x680/0x680
[  219.530132]  ? call_rcu_bh+0x10/0x10
[  219.530166]  ? debug_check_no_locks_freed+0x2a0/0x2a0
[  219.530201]  ? trace_raw_output_rcu_utilization+0xa0/0xa0
[  219.530267]  ? trace_raw_output_rcu_utilization+0xa0/0xa0
[  219.530337]  ? rcu_lockdep_current_cpu_online+0xdc/0x130
[  219.530370]  ? sched_cpu_activate+0x1e0/0x1e0
[  219.530397]  cpuhp_invoke_callback+0x160/0x15f0
[  219.530424]  ? lock_acquire+0x138/0x3c0
[  219.530445]  ? lock_acquire+0x138/0x3c0
[  219.530471]  ? cpuhp_thread_fun+0xaf/0x710
[  219.530507]  ? pci_mmcfg_check_reserved+0x100/0x100
[  219.530565]  cpuhp_thread_fun+0x35e/0x710
[  219.530618]  ? cpuhp_complete_idle_dead+0x10/0x10
[  219.530639]  smpboot_thread_fn+0x50a/0x7f0
[  219.530678]  ? sort_range+0x20/0x20
[  219.530709]  ? __kthread_parkme+0xba/0x1f0
[  219.530739]  ? schedule+0x84/0x1a0
[  219.530768]  ? __kthread_parkme+0xbf/0x1f0
[  219.530805]  ? sort_range+0x20/0x20
[  219.530831]  kthread+0x30a/0x3d0
[  219.530859]  ? _kthread_create_on_node+0xb0/0xb0
[  219.530900]  ret_from_fork+0x24/0x50
[  219.530999] Code: 01 00 00 00 85 c0 74 4a 89 e8 5b 5d c3 80 3d 48 37 4e 00 00 75 f2 89 c6 48 c7 c7 40 f0 61 c0 c6 05 36 37 4e 00 01 e8 ed 2a e1 c2 <0f> ff eb d9 80 3d 3f 37 4e 00 00 75 94 48 c7 c7 60 e8 61 c0 c6
[  219.531880] ---[ end trace 18ec0139488ea0c8 ]---
[  219.607967] IRQ 16: no longer affine to CPU1
[  219.670291] IRQ 24: no longer affine to CPU2
[  219.701489] IRQ 8: no longer affine to CPU3
[  219.701529] IRQ 9: no longer affine to CPU3
[  219.701582] IRQ 18: no longer affine to CPU3
[  219.701640] IRQ 25: no longer affine to CPU3
[  219.743857]  cache: parent cpu1 should not be sleeping
[  219.784549]  cache: parent cpu2 should not be sleeping
[  219.816041]  cache: parent cpu3 should not be sleeping

v2: Add Returns: information to intel_runtime_pm_get_if_in_use() kerneldoc.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180219125046.19363-1-chris@chris-wilson.co.uk

drm: intel_dpio_phy: fix kernel-doc comments at nested struct

The in-lined comments for channel.port doesn't follow the syntax
described at kernel-doc document, causing the following warning:

$ ./scripts/kernel-doc -none drivers/gpu/drm/i915/intel_dpio_phy.c
drivers/gpu/drm/i915/intel_dpio_phy.c:154: warning: Function parameter or member 'channel.port' not described in 'bxt_ddi_phy_info'

While the best would be for the Kernel to deduce that from the
context, supporting it is not trivial. So, let's just stick with
the existing syntax.

[Jani: depends on "scripts: kernel-doc: support in-line comments on
nested structs/unions" to actually fix the warning.]

Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9ba9ac773f4f9e60770bd9169b0e46ac974d858a.1518788761.git.mchehab@s-opensource.com

drm/i915: Release connector iterator on a digital port conflict.

Hitting the failure path through check_digital_port_conflicts triggers:

================================================
WARNING: lock held when returning to user space!
4.16.0-rc1-CI-kasan_1+ #1 Tainted: G        W
------------------------------------------------
kms_3d/1439 is leaving the kernel with locks still held!
1 lock held by kms_3d/1439:
 #0:  (drm_connector_list_iter){.+.+}, at: [<000000003745d183>] intel_atomic_check+0x1d9d/0x3ff0 [i915]

Rearrange the code to have a single exit path through the unlock.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215091425.42364-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915/execlists: Remove too early assert

We can't assert that the execlists are active before we set the flag. So
perform the assert after we are expected to have marked the execlists
active.

Fixes: 339ccd35b42c ("drm/i915: Assert that we always complete a submission to guc/execlists")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180216153210.30551-1-chris@chris-wilson.co.uk

drm/i915: Assert that we always complete a submission to guc/execlists

The continual resubmission model for execlists (and emulated over guc)
requires that we keep feeding requests into the HW in order to generate
more CS interrupts to drain the rest of the queue. Add a couple of
asserts to ensure that we don't skip a cycle and come to a grinding
halt.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215162553.23348-1-chris@chris-wilson.co.uk

drm: move read_domains and write_domain into i915

i915 is the only driver using those fields in the drm_gem_object
structure, so they only waste memory for all other drivers.

Move the fields into drm_i915_gem_object instead and patch the i915 code
with the following sed commands:

sed -i "s/obj->base.read_domains/obj->read_domains/g" drivers/gpu/drm/i915/*.c drivers/gpu/drm/i915/*/*.c
sed -i "s/obj->base.write_domain/obj->write_domain/g" drivers/gpu/drm/i915/*.c drivers/gpu/drm/i915/*/*.c

Change is only compile tested.

v2: move fields around as suggested by Chris.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180216124338.9087-1-christian.koenig@amd.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/cnl: Fix PORT_TX_DW5/7 register address

Register Address for CNL_PORT_DW5_LN0_D is 0x162E54, but current code is
defining it as 0x162ED4. Similarly for CNL_PORT_DW7_LN0_D register address
is defined 0x162EDC instead of 0x162E5C, fix it.

Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Fixes: 04416108ccea ("drm/i915/cnl: Add registers related to voltage swing sequences.")
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215095643.3844-2-mahesh1.kumar@intel.com

drm/i915: Estimate and update missed vblanks.

The frame counter may have got reset between disabling and enabling vblank
interrupts due to DMC putting the hardware to DC5/6 states if PSR was
active. The frame counter could also have stalled if PSR was active in case
there was no DMC. The frame counter resetting has a user visible impact
of screen freezes.

Make use of drm_vblank_restore() to compute missed vblanks for the duration
in which vblank interrupts were disabled and update the vblank counter with
this value as diff. There's no need to check if PSR was actually active in
the interrupt disabled duration, so simplify the check to a feature check.

Enabling vblank interrupts wakes up the hardware from DC5/6 and prevents it
from going back again as long as the there are pending interrupts. So, we
don't have to explicity disallow DC5/6 after enabling vblank interrupts to
keep the counter running.

This change is not applicable to CHV, as enabling interrupts does not
prevent the hardware from activating PSR.

v2: Added comments(Rodrigo) and rewrote commit message.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-10-dhinakaran.pandiyan@intel.com

drm/vblank: Restoring vblank counts after device PM events.

The HW frame counter can get reset if device enters a low power state after
vblank interrupts were disabled. This messes up any following vblank count
update as a negative diff (huge unsigned diff) is calculated from the HW
frame counter change. We cannot ignore negative diffs altogther as there
could be legitimate wrap arounds. So, allow drivers to update vblank->count
with missed vblanks for the time interrupts were disabled. This is similar
to _crtc_vblank_on() except that vblanks interrupts are not enabled at the
end as this function is expected to be called from the driver
_enable_vblank() vfunc.

v2: drm_crtc_vblank_restore should take crtc as arg. (Chris)
    Add docs and sprinkle some asserts.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-9-dhinakaran.pandiyan@intel.com

drm/vblank: Do not update vblank count if interrupts are already disabled.

Updating vblank counts requires register reads and these reads may not
return meaningful values if the device was in a low power state after
vblank interrupts were last disabled. So, update the count only if vblank
interrupts are enabled. Secondly, this means the registers should be read
before disabling vblank interrupts.

v2: Don't check vblank->enabled outside it's lock (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-8-dhinakaran.pandiyan@intel.com

drm/atomic: Handle 64-bit return from drm_crtc_vblank_count()

570e86963a51 ("drm: Widen vblank count to 64-bits [v3]") changed the
return type for drm_crtc_vblank_count() to u64.

The flip ioctl receives a 32-bit target sequence from user space and is
compared against the current sequence from drm_crtc_vblank_count(). So,
typecast return from drm_crtc_vblank_count() explicitly to add clarity.

__drm_crtcs_state.last_vblank_count however only ever stores the value from
drm_crtc_vblank_count() and can be upgraded to u64.

Cc: Keith Packard <keithp@keithp.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-7-dhinakaran.pandiyan@intel.com

drm/tegra: Handle 64-bit return from drm_crtc_vblank_count()

570e86963a51 ("drm: Widen vblank count to 64-bits [v3]") changed the
return type for drm_crtc_vblank_count() to u64. This could cause
potential problems if the return value is used in arithmetic operations
with a 32-bit reference HW vblank count. Explicitly typecasting this
down to u32 either fixes a potential problem or serves to add clarity in
case the implicit typecasting was already correct.

Cc: Keith Packard <keithp@keithp.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-6-dhinakaran.pandiyan@intel.com

drm/radeon: Handle 64-bit return from drm_crtc_vblank_count()

570e86963a51 ("drm: Widen vblank count to 64-bits [v3]") changed the
return type for drm_crtc_vblank_count() to u64. This could cause
potential problems if the return value is used in arithmetic operations
with a 32-bit reference HW vblank count. Explicitly typecasting this down
to u32 either fixes a potential problem or serves to add clarity in case
the implicit typecasting was already correct.

Cc: Keith Packard <keithp@keithp.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-5-dhinakaran.pandiyan@intel.com

drm/amdgpu: Handle 64-bit return from drm_crtc_vblank_count()

570e86963a51 ("drm: Widen vblank count to 64-bits [v3]") changed the
return type for drm_crtc_vblank_count() to u64. This could cause
potential problems if the return value is used in arithmetic operations
with a 32-bit reference HW vblank count. Explicitly typecasting this down
to u32 either fixes a potential problem or serves to add clarity in case
the typecasting was implicitly done.

Cc: Keith Packard <keithp@keithp.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com> for both this patch
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-4-dhinakaran.pandiyan@intel.com

drm/i915: Handle 64-bit return from drm_crtc_vblank_count()

570e86963a51 ("drm: Widen vblank count to 64-bits [v3]") changed the
return type for drm_crtc_vblank_count() to u64, store all the bits
without truncating. There is no need to type cast this value down to
32-bits.

Cc: Keith Packard <keithp@keithp.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-3-dhinakaran.pandiyan@intel.com

drm/i915/vblank: Make the vblank counter u64 -> u32 typecast explicit

Core returns a u64 vblank count and intel_crtc_get_vblank_counter()
expects a 32-bit value. Make the typecast explicit to add clarity.

Cc: Keith Packard <keithp@keithp.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-2-dhinakaran.pandiyan@intel.com

drm/vblank: Data type fixes for 64-bit vblank sequences.

drm_vblank_count() has an u32 type returning what is a 64-bit vblank count.
The effect of this is when drm_wait_vblank_ioctl() tries to widen the user
space requested vblank sequence using this clipped 32-bit count(when the
value is >= 2^32) as reference, the requested sequence remains a 32-bit
value and gets queued like that. However, the code that checks if the
requested sequence has passed compares this against the 64-bit vblank
count.

With drm_vblank_count() returning all bits of the vblank count, update
drm_crtc_accurate_vblank_count() so that drm_crtc_arm_vblank_event() queues
the correct sequence. Otherwise, this leads to prolonged waits for a vblank
sequence when the current count is >=2^32.

Finally, fix drm_wait_one_vblank() too.

v2: Commit message fix (Keith)
    Squash commits (Rodrigo)

Fixes: 570e86963a51 ("drm: Widen vblank count to 64-bits [v3]")
Cc: Keith Packard <keithp@keithp.com>
Cc: Michel Dänzer <michel@daenzer.net>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-1-dhinakaran.pandiyan@intel.com

drm/i915/selftests: fix inconsistent IS_ERR and PTR_ERR

Fix inconsistent IS_ERR and PTR_ERR in shrink_boom.
The proper pointer to use is _explode_ instead of _purge_.

This issue was detected with the help of Coccinelle.

Fixes: fe215c8bc426 ("drm/i915/selftests: add missing gtt shrinker test")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214211234.GA22341@embeddedgus
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Store platform_mask inside the static device info

Rather than deriving the platform_mask from the
intel_device_static_info->platform at runtime, pre-fill it in the static
data.

v2: Undefine macros at end of their scope

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215081930.11477-3-chris@chris-wilson.co.uk

drm/i915: Always define GEN as part of GENx_FEATURES

Be consistent and define the device's GEN as part of the GENx_FEATURE.
It will be overridden by the next gen upon inheriting, as per usual.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215081930.11477-2-chris@chris-wilson.co.uk

drm/i915: Store gen_mask inside the static device info

Rather than deriving the gen_mask from the static intel_device_info->gen
at runtime, pre-fill it in the static data.

v2: Undefine local macros at end of their scope.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215081930.11477-1-chris@chris-wilson.co.uk

drm/i915/gtt: Convert WARN_ON to GEM debugging

As we presume that we have sufficient coverage of CI for new machines
and new code paths, we do not need to have user impacting WARN_ON for
programming errors inside i915_gem_gtt.c, so convert those over to
GEM_BUG_ON. This leaves the memory debugging WARN_ON in place as they
are not so easy to exercise with CI.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215110759.28603-1-chris@chris-wilson.co.uk

drm/i915: Clean up ancient doc comments for i915_ioc32.c

As befitting a file dedicated to the mistakes of the past,

drivers/gpu/drm/i915/i915_ioc32.c:2: warning: Cannot understand  * \file i915_ioc32.c
 on line 2 - I thought it was a doc line
drivers/gpu/drm/i915/i915_ioc32.c:82: warning: Function parameter or member 'filp' not described in 'i915_compat_ioctl'
drivers/gpu/drm/i915/i915_ioc32.c:82: warning: Function parameter or member 'cmd' not described in 'i915_compat_ioctl'
drivers/gpu/drm/i915/i915_ioc32.c:82: warning: Function parameter or member 'arg' not described in 'i915_compat_ioctl'

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214160720.19673-1-chris@chris-wilson.co.uk

drm/i915/audio: fix check for av_enc_map overflow

Turns out -1 >= ARRAY_SIZE() is always true. Move the bounds check where
we know pipe >= 0 and next to the array indexing where it makes most
sense.

Fixes: 9965db26ac05 ("drm/i915: Check for fused or unused pipes")
Fixes: 0b7029b7e43f ("drm/i915: Check for fused or unused pipes")
Cc: <stable@vger.kernel.org> # v4.10+
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214173840.25360-1-jani.nikula@intel.com

drm/i915/cnl: Remove alpha_support protection

We now have a stable cnl on our CI and it seems mostly
green without big risks of blank screen or anything
blowing up on linux installations in the future.

As a reminder i915.alpha_support was created to protect
future linux installation's iso images that might contain a
kernel from the enabling time of the new platform. Without this
protection most of linux installation was recommending
nomodeset option during installation that was getting stick
there after installation.

Specifically, alpha support says nothing about the development
state of the hardware, and everything about the state of the
driver in a kernel release.

This is semantically no different from the old
preliminary_hw_support flag, but the old one was all too often
interpreted as (preliminary hw) support instead of the intended
(preliminary) hw support, and it was misleading for everyone.
Hence the rename.

v2: Fix the typos and include more history about the parameter
rename on commit message. (Jani)

Reference: https://intel-gfx-ci.01.org/tree/drm-tip/fi-cnl-y3.html
Cc: James Ausmus <james.ausmus@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Jani Saarinen <jani.saarinen@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214204205.4446-1-rodrigo.vivi@intel.com

drm/i915/cnl: Sync PCI ID with Spec.

Add one missing PCI ID and sort them in a way
that gets easier to review and compare against spec's
table.

When trying to sync libdrm and mesa id list with kernel
and spec I noticed something was wrong and we were missing
a pci id. So to make our lives easier when checking against
spec let's simplify and sort like spec does.

BSpec: 13621

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180208073219.27860-1-rodrigo.vivi@intel.com

drm/i915: Fix rsvd2 mask when out-fence is returned

GENMASK_ULL wants the high bit of the mask first. The current value
cancels the in-fence when an out-fence is returned.

Fixes: fec0445caa273 ("drm/i915: Support explicit fencing for execbuf")
Testcase: igt/gem_exec_fence/keep-in-fence*
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214191827.8465-1-daniele.ceraolospurio@intel.com
Cc: <stable@vger.kernel.org> # v4.12+

drm/i915: Fixup kerneldoc for intel_pm.c

drivers/gpu/drm/i915/intel_pm.c:750: warning: Function parameter or member 'fifo_size' not described in 'intel_calculate_wm'
drivers/gpu/drm/i915/intel_pm.c:5900: warning: Function parameter or member 'crtc' not described in 'intel_update_watermarks'

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214140303.1561-1-chris@chris-wilson.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915: Fixup kerneldoc

drivers/gpu/drm/i915/intel_display.c:569: warning: Function parameter or member 'dev_priv' not described in 'intel_PLL_is_valid'
drivers/gpu/drm/i915/intel_display.c:569: warning: Function parameter or member 'limit' not described in 'intel_PLL_is_valid'
drivers/gpu/drm/i915/intel_display.c:569: warning: Function parameter or member 'clock' not described in 'intel_PLL_is_valid'
drivers/gpu/drm/i915/intel_display.c:4769: warning: Function parameter or member 'crtc_state' not described in 'skl_update_scaler_plane'
drivers/gpu/drm/i915/intel_display.c:4769: warning: Excess function parameter 'state' description in 'skl_update_scaler_plane'
drivers/gpu/drm/i915/intel_display.c:4967: warning: Function parameter or member 'new_crtc_state' not described in 'intel_post_enable_primary'
drivers/gpu/drm/i915/intel_display.c:12650: warning: Function parameter or member 'new_state' not described in 'intel_prepare_plane_fb'
drivers/gpu/drm/i915/intel_display.c:12650: warning: Excess function parameter 'fb' description in 'intel_prepare_plane_fb'
drivers/gpu/drm/i915/intel_display.c:12763: warning: Function parameter or member 'old_state' not described in 'intel_cleanup_plane_fb'
drivers/gpu/drm/i915/intel_display.c:12763: warning: Excess function parameter 'fb' description in 'intel_cleanup_plane_fb'

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214134922.28761-2-chris@chris-wilson.co.uk

drm/i915/atomic: Fixup kerneldoc

drivers/gpu/drm/i915/intel_atomic.c:198: warning: Function parameter or member 'state' not described in 'intel_crtc_destroy_state'
drivers/gpu/drm/i915/intel_atomic.c:222: warning: Function parameter or member 'intel_crtc' not described in 'intel_atomic_setup_scalers'
drivers/gpu/drm/i915/intel_atomic.c:222: warning: Excess function parameter 'crtc' description in 'intel_atomic_setup_scalers'

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214134922.28761-1-chris@chris-wilson.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915: Fixup kerneldoc for intel_uc_fw_upload()

Just a parameter name change that was lost to kerneldoc.

drivers/gpu/drm/i915/intel_uc_fw.c:209: warning: Function parameter or member 'xfer' not described in 'intel_uc_fw_upload'
drivers/gpu/drm/i915/intel_uc_fw.c:209: warning: Excess function parameter 'loader' description in 'intel_uc_fw_upload'

v2: Add the Returns:

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214105332.30230-1-chris@chris-wilson.co.uk

drm/i915: Add missing kerneldoc parameters for huc_ucode_xfer

During the recent upheaval to uc, the parameters to huc_ucode_xfer
were changed, but the kerneldoc left behind.

drivers/gpu/drm/i915/intel_huc.c:128: warning: Function parameter or member 'huc_fw' not described in 'huc_ucode_xfer'
drivers/gpu/drm/i915/intel_huc.c:128: warning: Function parameter or member 'vma' not described in 'huc_ucode_xfer'
drivers/gpu/drm/i915/intel_huc.c:128: warning: Excess function parameter 'dev_priv' description in 'huc_ucode_xfer'

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214104040.4532-1-chris@chris-wilson.co.uk

drm/i915/lvds: Fixup commentary

Remove the kerneldoc markup applied to non-kerneldoc comments and
convert the multiline comments to the canonical style.

drivers/gpu/drm/i915/intel_lvds.c:313: warning: Function parameter or member 'encoder' not described in 'intel_enable_lvds'
drivers/gpu/drm/i915/intel_lvds.c:313: warning: Function parameter or member 'pipe_config' not described in 'intel_enable_lvds'
drivers/gpu/drm/i915/intel_lvds.c:313: warning: Function parameter or member 'conn_state' not described in 'intel_enable_lvds'
drivers/gpu/drm/i915/intel_lvds.c:453: warning: Function parameter or member 'connector' not described in 'intel_lvds_detect'
drivers/gpu/drm/i915/intel_lvds.c:453: warning: Function parameter or member 'force' not described in 'intel_lvds_detect'
drivers/gpu/drm/i915/intel_lvds.c:471: warning: Function parameter or member 'connector' not described in 'intel_lvds_get_modes'
drivers/gpu/drm/i915/intel_lvds.c:932: warning: Function parameter or member 'dev_priv' not described in 'intel_lvds_init'
drivers/gpu/drm/i915/intel_lvds.c:932: warning: Excess function parameter 'dev' description in 'intel_lvds_init'

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214092909.27040-4-chris@chris-wilson.co.uk

drm/i915/dvo: Fixup commentary

Remove the kerneldoc markup applied to non-kerneldoc comments and
convert the multiline comments to the canonical style.

drivers/gpu/drm/i915/intel_dvo.c:303: warning: Function parameter or member 'connector' not described in 'intel_dvo_detect'
drivers/gpu/drm/i915/intel_dvo.c:303: warning: Function parameter or member 'force' not described in 'intel_dvo_detect'
drivers/gpu/drm/i915/intel_dvo.c:382: warning: Function parameter or member 'encoder' not described in 'intel_dvo_get_current_mode'

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214092909.27040-3-chris@chris-wilson.co.uk

drm/i915/dvo: Remove incorrect kerneldoc markups

Regular comments where being marked up for kerneldoc, but were not
formatted properly. Remove the markup to remove the warnings.

drivers/gpu/drm/i915/dvo_ivch.c:192: warning: Function parameter or member 'dvo' not described in 'ivch_read'
drivers/gpu/drm/i915/dvo_ivch.c:192: warning: Function parameter or member 'addr' not described in 'ivch_read'
drivers/gpu/drm/i915/dvo_ivch.c:192: warning: Function parameter or member 'data' not described in 'ivch_read'

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214092909.27040-2-chris@chris-wilson.co.uk

drm/i915/crt: Remove obsolete kerneldoc-esque comment

The code describes what it is doing quite well; and that is now much
more complex than what the old comment would let you believe.

drivers/gpu/drm/i915/intel_crt.c:486: warning: Function parameter or member 'connector' not described in 'intel_crt_detect_hotplug'

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214092909.27040-1-chris@chris-wilson.co.uk

drm/i915/panel: Split range scaling calculation for readiblity

Split the 64b multiplication from the division so that it doesn't sprawl
across a couple of lines and use mul_u32_u32() instead of open-coding
the 64b conversion.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214091747.12753-2-chris@chris-wilson.co.uk

drm/i915/panel: Add missing parameters to kerneldoc

drivers/gpu/drm/i915/intel_panel.c:409: warning: Function parameter or member 'source_min' not described in 'scale'
drivers/gpu/drm/i915/intel_panel.c:409: warning: Function parameter or member 'source_max' not described in 'scale'
drivers/gpu/drm/i915/intel_panel.c:409: warning: Function parameter or member 'target_min' not described in 'scale'
drivers/gpu/drm/i915/intel_panel.c:409: warning: Function parameter or member 'target_max' not described in 'scale'

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214091747.12753-1-chris@chris-wilson.co.uk
Link: https://patchwork.freedesktop.org/patch/msgid/20180214091747.12753-2-chris@chris-wilson.co.uk

drm/i915/sdvo: Tidy up commentary

Drop the kerneldoc markup from the non-kerneldoc comments and convert
the multi-line comments to the canonical format.

drivers/gpu/drm/i915/intel_sdvo.c:223: warning: Function parameter or member 'intel_sdvo' not described in 'intel_sdvo_write_sdvox'
drivers/gpu/drm/i915/intel_sdvo.c:223: warning: Function parameter or member 'val' not described in 'intel_sdvo_write_sdvox'
drivers/gpu/drm/i915/intel_sdvo.c:653: warning: Function parameter or member 'intel_sdvo' not described in 'intel_sdvo_get_trained_inputs'
drivers/gpu/drm/i915/intel_sdvo.c:653: warning: Function parameter or member 'input_1' not described in 'intel_sdvo_get_trained_inputs'
drivers/gpu/drm/i915/intel_sdvo.c:653: warning: Function parameter or member 'input_2' not described in 'intel_sdvo_get_trained_inputs'
drivers/gpu/drm/i915/intel_sdvo.c:2311: warning: Function parameter or member 'dev_priv' not described in 'intel_sdvo_select_ddc_bus'
drivers/gpu/drm/i915/intel_sdvo.c:2311: warning: Function parameter or member 'sdvo' not described in 'intel_sdvo_select_ddc_bus'

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214090905.4747-1-chris@chris-wilson.co.uk

drm/i915/tv: Cleanup up obsolete comments

The ages old kerneldoc-esque comments still refer to the original stubs
and not the more complete functions. As they were only describing the
external entry points (or at least thought themselves to be, they had
drifted!), they don't provide any commentary for the code flow.

drivers/gpu/drm/i915/intel_tv.c:379: warning: cannot understand function prototype: 'const struct tv_mode tv_modes[] = '
drivers/gpu/drm/i915/intel_tv.c:1133: warning: bad line:
drivers/gpu/drm/i915/intel_tv.c:1140: warning: Function parameter or member 'intel_tv' not described in 'intel_tv_detect_type'
drivers/gpu/drm/i915/intel_tv.c:1140: warning: Function parameter or member 'connector' not described in 'intel_tv_detect_type'
drivers/gpu/drm/i915/intel_tv.c:1272: warning: Function parameter or member 'connector' not described in 'intel_tv_detect'
drivers/gpu/drm/i915/intel_tv.c:1272: warning: Function parameter or member 'ctx' not described in 'intel_tv_detect'
drivers/gpu/drm/i915/intel_tv.c:1272: warning: Function parameter or member 'force' not described in 'intel_tv_detect'
drivers/gpu/drm/i915/intel_tv.c:1351: warning: Function parameter or member 'connector' not described in 'intel_tv_get_modes'

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214085814.2565-1-chris@chris-wilson.co.uk