OSDN Git Service
Shuming Fan [Wed, 16 Nov 2022 09:03:18 +0000 (17:03 +0800)]
ASoC: rt711-sdca: fix the latency time of clock stop prepare state machine transitions
Due to the hardware behavior, it takes some time for CBJ detection/impedance sensing/de-bounce.
The ClockStop_NotFinished flag will be raised until these functions are completed.
In ClockStopMode0 mode case, the SdW controller might check this flag from D3 to D0 when the
jack detection interrupt happened.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20221116090318.5017-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Richard Fitzgerald [Fri, 4 Nov 2022 13:22:13 +0000 (13:22 +0000)]
ASoC: soc-pcm: Don't zero TDM masks in __soc_pcm_open()
The DAI tx_mask and rx_mask are set by snd_soc_dai_set_tdm_slot()
and used by later code that depends on the TDM settings. So
__soc_pcm_open() should not be obliterating those mask values.
The code in __soc_pcm_hw_params() uses these masks to calculate the
active channels so that only the AIF_IN/AIF_OUT widgets for the
active TDM slots are enabled. The zeroing of the masks in
__soc_pcm_open() disables this functionality so all AIF widgets
were enabled even for channels that are not assigned to a TDM slot.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes:
2e5894d73789 ("ASoC: pcm: Add support for DAI multicodec")
Link: https://lore.kernel.org/r/20221104132213.121847-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Detlev Casanova [Thu, 10 Nov 2022 19:06:12 +0000 (14:06 -0500)]
ASoC: sgtl5000: Reset the CHIP_CLK_CTRL reg on remove
Since commit
bf2aebccddef ("ASoC: sgtl5000: Fix noise on shutdown/remove"),
the device power control registers are reset when the driver is
removed/shutdown.
This is an issue when the device is configured to use the PLL clock. The
device will stop responding if it is still configured to use the PLL
clock but the PLL clock is powered down.
When rebooting linux, the probe function will show:
sgtl5000 0-000a: Error reading chip id -11
Make sure that the CHIP_CLK_CTRL is reset to its default value before
powering down the device.
Fixes:
bf2aebccddef ("ASoC: sgtl5000: Fix noise on shutdown/remove")
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20221110190612.1341469-1-detlev.casanova@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Junxiao Chang [Wed, 9 Nov 2022 23:40:23 +0000 (07:40 +0800)]
ASoC: hdac_hda: fix hda pcm buffer overflow issue
When KASAN is enabled, below log might be dumped with Intel EHL hardware:
[ 48.583597] ==================================================================
[ 48.585921] BUG: KASAN: slab-out-of-bounds in hdac_hda_dai_hw_params+0x20a/0x22b [snd_soc_hdac_hda]
[ 48.587995] Write of size 4 at addr
ffff888103489708 by task pulseaudio/759
[ 48.589237] CPU: 2 PID: 759 Comm: pulseaudio Tainted: G U E 5.15.71-intel-ese-standard-lts #9
[ 48.591272] Hardware name: Intel Corporation Elkhart Lake Embedded Platform/ElkhartLake LPDDR4x T3 CRB, BIOS EHLSFWI1.R00.4251.A01.
2206130432 06/13/2022
[ 48.593010] Call Trace:
[ 48.593648] <TASK>
[ 48.593852] dump_stack_lvl+0x34/0x48
[ 48.594404] print_address_description.constprop.0+0x1f/0x140
[ 48.595174] ? hdac_hda_dai_hw_params+0x20a/0x22b [snd_soc_hdac_hda]
[ 48.595868] ? hdac_hda_dai_hw_params+0x20a/0x22b [snd_soc_hdac_hda]
[ 48.596519] kasan_report.cold+0x7f/0x11b
[ 48.597003] ? hdac_hda_dai_hw_params+0x20a/0x22b [snd_soc_hdac_hda]
[ 48.597885] hdac_hda_dai_hw_params+0x20a/0x22b [snd_soc_hdac_hda]
HDAC_LAST_DAI_ID is last index id, pcm buffer array size should
be +1 to avoid out of bound access.
Fixes:
608b8c36c371 ("ASoC: hdac_hda: add support for HDMI/DP as a HDA codec")
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Junxiao Chang <junxiao.chang@intel.com>
Signed-off-by: Furong Zhou <furong.zhou@intel.com>
Link: https://lore.kernel.org/r/20221109234023.3111035-1-junxiao.chang@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Olivier Moysan [Thu, 10 Nov 2022 08:44:06 +0000 (09:44 +0100)]
ASoC: stm32: i2s: remove irqf_oneshot flag
The IRQF_ONESHOT flag allows to ensure that the interrupt is not
unmasked after the hard interrupt context handler has been executed
and the thread has been woken. The interrupt line is unmasked after
the thread handler function has been executed.
The STM32 I2S driver does not implement a threaded IRQ handler.
So, the IRQF_ONESHOT flag is not useful in I2S driver.
Remove this flag to allow the interrupt routine to be managed
as a thread in RT mode.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20221110084406.287117-1-olivier.moysan@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Chancel Liu [Wed, 9 Nov 2022 12:13:54 +0000 (20:13 +0800)]
ASoC: wm8962: Wait for updated value of WM8962_CLOCKING1 register
DSPCLK_DIV field in WM8962_CLOCKING1 register is used to generate
correct frequency of LRCLK and BCLK. Sometimes the read-only value
can't be updated timely after enabling SYSCLK. This results in wrong
calculation values. Delay is introduced here to wait for newest value
from register. The time of the delay should be at least 500~1000us
according to test.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221109121354.123958-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Olivier Moysan [Wed, 9 Nov 2022 17:08:49 +0000 (18:08 +0100)]
ASoC: stm32: dfsdm: manage cb buffers cleanup
Ensure that resources allocated by iio_channel_get_all_cb()
are released on driver unbind.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20221109170849.273719-1-olivier.moysan@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Zhu Ning [Fri, 28 Oct 2022 02:04:56 +0000 (10:04 +0800)]
ASoC: sof_es8336: reduce pop noise on speaker
The Speaker GPIO needs to be turned on slightly behind the codec turned on.
It also need to be turned off slightly before the codec turned down.
Current code uses delay in DAPM_EVENT to do it but the mdelay delays the
DAPM itself and thus has no effect. A delayed_work is added to turn on the
speaker.
The Speaker is turned off in .trigger since trigger is called slightly
before the DAPM events.
Signed-off-by: Zhu Ning <zhuning@everest-semi.com>
------------
v1: cancel delayed work while disabling speaker.
Link: https://lore.kernel.org/r/20221028020456.90286-1-zhuning0077@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Peter Ujfalusi [Mon, 7 Nov 2022 09:04:33 +0000 (11:04 +0200)]
ASoC: SOF: topology: No need to assign core ID if token parsing failed
Move the return value check before attempting to assign the core ID to the
swidget since we are going to fail the sof_widget_ready() and free up
swidget anyways.
Fixes:
909dadf21aae ("ASoC: SOF: topology: Make DAI widget parsing IPC agnostic")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20221107090433.5146-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Chen Zhongjin [Mon, 31 Oct 2022 13:40:31 +0000 (21:40 +0800)]
ASoC: soc-utils: Remove __exit for snd_soc_util_exit()
snd_soc_util_exit() is called in __init snd_soc_init() for cleanup.
Remove the __exit annotation for it to fix the build warning:
WARNING: modpost: sound/soc/snd-soc-core.o: section mismatch in reference: init_module (section: .init.text) -> snd_soc_util_exit (section: .exit.text)
Fixes:
6ec27c53886c ("ASoC: core: Fix use-after-free in snd_soc_exit()")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Link: https://lore.kernel.org/r/20221031134031.256511-1-chenzhongjin@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Jason Montleon [Thu, 3 Nov 2022 14:46:12 +0000 (10:46 -0400)]
ASoC: rt5677: fix legacy dai naming
Starting with 6.0-rc1 the CPU DAI is not registered and the sound
card is unavailable. Adding legacy_dai_naming causes it to function
properly again.
Fixes:
fc34ece41f71 ("ASoC: Refactor non_legacy_dai_naming flag")
Signed-off-by: Jason Montleon <jmontleo@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221103144612.4431-2-jmontleo@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Jason Montleon [Thu, 3 Nov 2022 14:46:11 +0000 (10:46 -0400)]
ASoC: rt5514: fix legacy dai naming
Starting with 6.0-rc1 these messages are logged and the sound card
is unavailable. Adding legacy_dai_naming to the rt5514-spi causes
it to function properly again.
[ 16.928454] kbl_r5514_5663_max kbl_r5514_5663_max: ASoC: CPU DAI
spi-PRP0001:00 not registered
[ 16.928561] platform kbl_r5514_5663_max: deferred probe pending
Fixes:
fc34ece41f71 ("ASoC: Refactor non_legacy_dai_naming flag")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=216641
Signed-off-by: Jason Montleon <jmontleo@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221103144612.4431-1-jmontleo@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kai Vehmanen [Tue, 1 Nov 2022 11:49:13 +0000 (13:49 +0200)]
ASoC: SOF: ipc3-topology: use old pipeline teardown flow with SOF2.1 and older
Originally in commit
b2ebcf42a48f ("ASoC: SOF: free widgets in
sof_tear_down_pipelines() for static pipelines"), freeing of pipeline
components at suspend was only done with recent FW as there were known
limitations in older firmware versions.
Tests show that if static pipelines are used, i.e. all pipelines are
setup whenever firmware is powered up, the reverse action of freeing all
components at power down, leads to firmware failures with also SOF2.0
and SOF2.1 based firmware.
The problems can be specific to certain topologies with e.g. components
not prepared to be freed at suspend (as this did not happen with older
SOF kernels).
To avoid hitting these problems when kernel is upgraded and used with an
older firmware, bump the firmware requirement to SOF2.2 or newer. If an
older firmware is used, and pipeline is a static one, do not free the
components at suspend. This ensures the suspend flow remains backwards
compatible with older firmware versions. This limitation does not apply
if the product configuration is updated to dynamic pipelines.
The limitation is not linked to firmware ABI, as the interface to free
pipeline components has been available already before ABI3.19. The
problem is in the implementation, so firmware version should be used to
decide whether it is safe to use the newer flow or not. This patch adds
a new SOF_FW_VER() macro to compare SOF firmware release versions.
Link: https://github.com/thesofproject/sof/issues/6475
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221101114913.1292671-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Mon, 31 Oct 2022 19:56:39 +0000 (15:56 -0400)]
ASoC: hda: intel-dsp-config: add ES83x6 quirk for IceLake
Yet another hardware variant we need to handle.
Link: https://github.com/thesofproject/linux/issues/3873
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20221031195639.250062-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Mon, 31 Oct 2022 19:58:36 +0000 (15:58 -0400)]
ASoC: Intel: soc-acpi: add ES83x6 support to IceLake
Missing entry to find a machine driver for ES83x6-based platforms.
Link: https://github.com/thesofproject/linux/issues/3873
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221031195836.250193-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Martin Povišer [Thu, 27 Oct 2022 09:58:00 +0000 (11:58 +0200)]
ASoC: tas2780: Fix set_tdm_slot in case of single slot
There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes:
eae9f9ce181b ("ASoC: add tas2780 driver")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-3-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Martin Povišer [Thu, 27 Oct 2022 09:57:59 +0000 (11:57 +0200)]
ASoC: tas2764: Fix set_tdm_slot in case of single slot
There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes:
827ed8a0fa50 ("ASoC: tas2764: Add the driver for the TAS2764")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-2-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Martin Povišer [Thu, 27 Oct 2022 09:57:58 +0000 (11:57 +0200)]
ASoC: tas2770: Fix set_tdm_slot in case of single slot
There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes:
1a476abc723e ("tas2770: add tas2770 smart PA kernel driver")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Maarten Zanders [Fri, 28 Oct 2022 14:11:28 +0000 (16:11 +0200)]
ASoC: fsl_asrc fsl_esai fsl_sai: allow CONFIG_PM=N
When CONFIG_PM=N, pm_runtime_put_sync() returns -ENOSYS
which breaks the probe function of these drivers.
Other users of pm_runtime_put_sync() typically don't check
the return value. In order to keep the program flow as
intended, check for -ENOSYS.
This commit is similar to commit
0434d3f (omap-mailbox.c).
Fixes:
cab04ab5900f ("ASoC: fsl_asrc: Don't use devm_regmap_init_mmio_clk")
Fixes:
203773e39347 ("ASoC: fsl_esai: Don't use devm_regmap_init_mmio_clk")
Fixes:
2277e7e36b4b ("ASoC: fsl_sai: Don't use devm_regmap_init_mmio_clk")
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20221028141129.100702-1-maarten.zanders@mind.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Chen Zhongjin [Fri, 28 Oct 2022 03:16:03 +0000 (11:16 +0800)]
ASoC: core: Fix use-after-free in snd_soc_exit()
KASAN reports a use-after-free:
BUG: KASAN: use-after-free in device_del+0xb5b/0xc60
Read of size 8 at addr
ffff888008655050 by task rmmod/387
CPU: 2 PID: 387 Comm: rmmod
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
Call Trace:
<TASK>
dump_stack_lvl+0x79/0x9a
print_report+0x17f/0x47b
kasan_report+0xbb/0xf0
device_del+0xb5b/0xc60
platform_device_del.part.0+0x24/0x200
platform_device_unregister+0x2e/0x40
snd_soc_exit+0xa/0x22 [snd_soc_core]
__do_sys_delete_module.constprop.0+0x34f/0x5b0
do_syscall_64+0x3a/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
...
</TASK>
It's bacause in snd_soc_init(), snd_soc_util_init() is possble to fail,
but its ret is ignored, which makes soc_dummy_dev unregistered twice.
snd_soc_init()
snd_soc_util_init()
platform_device_register_simple(soc_dummy_dev)
platform_driver_register() # fail
platform_device_unregister(soc_dummy_dev)
platform_driver_register() # success
...
snd_soc_exit()
snd_soc_util_exit()
# soc_dummy_dev will be unregistered for second time
To fix it, handle error and stop snd_soc_init() when util_init() fail.
Also clean debugfs when util_init() or driver_register() fail.
Fixes:
fb257897bf20 ("ASoC: Work around allmodconfig failure")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Link: https://lore.kernel.org/r/20221028031603.59416-1-chenzhongjin@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tzung-Bi Shih [Tue, 25 Oct 2022 02:49:29 +0000 (10:49 +0800)]
MAINTAINERS: update Tzung-Bi's email address
Use kernel.org account instead.
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20221025024929.2652134-1-tzungbi@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Hans de Goede [Tue, 25 Oct 2022 14:09:42 +0000 (16:09 +0200)]
ASoC: Intel: bytcht_es8316: Add quirk for the Nanote UMPC-01
The Nanote UMPC-01 mini laptop has stereo speakers, while the default
bytcht_es8316 settings assume a mono speaker setup. Add a quirk for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221025140942.509066-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Brent Mendelsohn [Mon, 24 Oct 2022 17:42:27 +0000 (18:42 +0100)]
ASoC: amd: yc: Add Alienware m17 R5 AMD into DMI table
This model requires an additional detection quirk to enable the
internal microphone - BIOS doesn't seem to support AcpDmicConnected
(nothing in acpidump output).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216590
Signed-off-by: Brent Mendelsohn <mendiebm@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20221024174227.4160-1-mendiebm@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Paul Cercueil [Tue, 25 Oct 2022 15:01:49 +0000 (16:01 +0100)]
ASoC: dapm: Don't use prefix for regulator name
When a component has a prefix, and uses a SND_SOC_DAPM_REGULATOR_SUPPLY,
the name of the regulator should not use the prefix, otherwise it won't
be properly matched in the DT/ACPI.
Fixes:
3caac759681e ("ASoC: soc-dapm.c: fixup snd_soc_dapm_new_control_unlocked() error handling")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221025150149.113129-1-paul@crapouillou.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Yang Yingliang [Thu, 20 Oct 2022 11:01:57 +0000 (19:01 +0800)]
ASoC: SOF: Intel: hda-codec: fix possible memory leak in hda_codec_device_init()
If snd_hdac_device_register() fails, 'codec' and name allocated in
dev_set_name() called in snd_hdac_device_init() are leaked. Fix this
by calling put_device(), so they can be freed in snd_hda_codec_dev_release()
and kobject_cleanup().
Fixes:
829c67319806 ("ASoC: SOF: Intel: Introduce HDA codec init and exit routines")
Fixes:
dfe66a18780d ("ALSA: hdac_ext: add extended HDA bus")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20221020110157.1450191-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Leohearts [Fri, 21 Oct 2022 06:34:32 +0000 (14:34 +0800)]
ASoC: amd: yc: Add Lenovo Thinkbook 14+ 2022 21D0 to quirks table
Lenovo Thinkbook 14+ 2022 (ThinkBook 14 G4+ ARA) uses Ryzen
6000 processor, and has the same microphone problem as other
ThinkPads with AMD Ryzen 6000 series CPUs, which has been
listed in https://bugzilla.kernel.org/show_bug.cgi?id=216267.
Adding 21D0 to quirks table solves this microphone problem
for ThinkBook 14 G4+ ARA.
Signed-off-by: Taroe Leohearts <leohearts@leohearts.com>
Link: https://lore.kernel.org/r/26B141B486BEF706+313d1732-e00c-ea41-3123-0d048d40ebb6@leohearts.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Yang Yingliang [Thu, 20 Oct 2022 10:59:37 +0000 (18:59 +0800)]
ASoC: Intel: Skylake: fix possible memory leak in skl_codec_device_init()
If snd_hdac_device_register() fails, 'codec' and name allocated in
dev_set_name() called in snd_hdac_device_init() are leaked. Fix this
by calling put_device(), so they can be freed in snd_hda_codec_dev_release()
and kobject_cleanup().
Fixes:
e4746d94d00c ("ASoC: Intel: Skylake: Introduce HDA codec init and exit routines")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Suggested-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221020105937.1448951-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Wed, 19 Oct 2022 15:49:26 +0000 (10:49 -0500)]
ASoC: SOF: Intel: pci-tgl: fix ADL-N descriptor
ADL-N uses a different signing key, which means we can't reuse the
regular ADL descriptor used for ADL-P/M/S.
Fixes:
cd57eb3c403cb ("ASoC: SOF: Intel: pci-tgl: add ADL-N support")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221019154926.163539-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Srinivasa Rao Mandadapu [Sat, 15 Oct 2022 09:18:50 +0000 (14:48 +0530)]
ASoC: qcom: lpass-cpu: Mark HDMI TX parity register as volatile
Update LPASS_HDMI_TX_PARITY_ADDR register as volatile, to fix
dp audio failures observed with some of external monitors.
Fixes:
7cb37b7bd0d3 ("ASoC: qcom: Add support for lpass hdmi driver")
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1665825530-7593-1-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
linkt [Tue, 11 Oct 2022 02:51:36 +0000 (10:51 +0800)]
ASoC: amd: yc: Adding Lenovo ThinkBook 14 Gen 4+ ARA and Lenovo ThinkBook 16 Gen 4+ ARA to the Quirks List
Lenovo ThinkBook 14 Gen 4+ ARA and ThinkBook 16 Gen 4+ ARA
need to be added to the list of quirks for the microphone to work properly.
Signed-off-by: linkt <xazrael@hotmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/MEYPR01MB8397A3C27DE6206FA3EF834DB6239@MEYPR01MB8397.ausprd01.prod.outlook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Wed, 19 Oct 2022 15:37:01 +0000 (16:37 +0100)]
ASoC: jz4752b: Capture fixes
Merge series from Siarhei Volkau <lis8215@gmail.com>:
The patchset fixes:
- Line In path stays powered off during capturing or
bypass to mixer.
- incorrectly represented dB values in alsamixer, et al.
- incorrect represented Capture input selector in alsamixer
in Playback tab.
- wrong control selected as Capture Master
Colin Ian King [Wed, 19 Oct 2022 07:16:39 +0000 (08:16 +0100)]
ASoC: codecs: jz4725b: Fix spelling mistake "Sourc" -> "Source", "Routee" -> "Route"
There are two spelling mistakes in codec routing description. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221019071639.1003730-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Aidan MacDonald [Wed, 19 Oct 2022 01:23:02 +0000 (02:23 +0100)]
ASoC: simple-card: Fix up checks for HW param fixups
The "convert-xxx" properties only have an effect for DPCM DAI links.
A DAI link is only created as DPCM if the device tree requires it;
part of this involves checking for the use of "convert-xxx" properties.
When the convert-sample-format property was added, the checks got out
of sync. A DAI link that specified only convert-sample-format but did
not pass any of the other DPCM checks would not go into DPCM mode and
the convert-sample-format property would be silently ignored.
Fix this by adding a function to do the "convert-xxx" property checks,
instead of open-coding it in simple-card and audio-graph-card. And add
"convert-sample-format" to the check function so that DAI links using
it will be initialized correctly.
Fixes:
047a05366f4b ("ASoC: simple-card-utils: Fixup DAI sample format")
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Acked-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/20221019012302.633830-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shuming Fan [Wed, 19 Oct 2022 09:57:15 +0000 (17:57 +0800)]
ASoC: rt1308-sdw: add the default value of some registers
The driver missed the default value of register 0xc070/0xc360.
This patch adds that default value to avoid invalid register access
when the device doesn't be enumerated yet.
BugLink: https://github.com/thesofproject/linux/issues/3924
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20221019095715.31082-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shuming Fan [Wed, 19 Oct 2022 09:57:31 +0000 (17:57 +0800)]
ASoC: rt1308-sdw: update the preset settings
This patch updates the pad control and checks the
hardware version to set the different preset settings.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20221019095731.31101-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kai Vehmanen [Tue, 18 Oct 2022 12:13:32 +0000 (15:13 +0300)]
ASoC: SOF: ipc4-mtrace: protect per-core nodes against multiple open
Add protection against multiple open of the mtrace/coreN debugfs
nodes. This is not supported in the implementation, and this will
show up as unexpected behaviour of the interface, and potential
use of already freed memory.
Fixes:
f4ea22f7aa75 ("ASoC: SOF: ipc4: Add support for mtrace log extraction")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20221018121332.20802-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Yong Zhi [Mon, 17 Oct 2022 20:57:28 +0000 (15:57 -0500)]
ASoC: Intel: sof_rt5682: Add quirk for Rex board
Add mtl_mx98357_rt5682 driver data for Chrome Rex board support.
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221017205728.210813-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Mon, 17 Oct 2022 20:40:04 +0000 (15:40 -0500)]
ASoC: SOF: Intel: pci-mtl: fix firmware name
Initial IPC4 tests used the same conventions as previous reference
closed-source firmware, but for MeteorLake the convention is the same
as previous SOF releases (sof-<platform>.ri). Only the prefix changes
to avoid confusions between IPC types.
This change has no impact on users since the firmware has not yet been
released.
Fixes:
064520e8aeaa2 ("ASoC: SOF: Intel: Add support for MeteorLake (MTL)")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20221017204004.207446-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart [Mon, 17 Oct 2022 20:40:54 +0000 (15:40 -0500)]
ASoC: Intel: sof_sdw: add quirk variant for LAPBC710 NUC15
Some NUC15 LAPBC710 devices don't expose the same DMI information as
the Intel reference, add additional entry in the match table.
BugLink: https://github.com/thesofproject/linux/issues/3885
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221017204054.207512-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Randy Dunlap [Sat, 15 Oct 2022 00:12:28 +0000 (17:12 -0700)]
ASoC: qcom: SND_SOC_SC7180 optionally depends on SOUNDWIRE
If SOUNDWIRE is enabled, then SND_SOC_SC7180 should depend on
SOUNDWIRE to prevent SOUNDWIRE=m and SND_SOC_SC7180=y, which causes
build errors:
s390-linux-ld: sound/soc/qcom/common.o: in function `qcom_snd_sdw_prepare':
common.c:(.text+0x140): undefined reference to `sdw_disable_stream'
s390-linux-ld: common.c:(.text+0x14a): undefined reference to `sdw_deprepare_stream'
s390-linux-ld: common.c:(.text+0x158): undefined reference to `sdw_prepare_stream'
s390-linux-ld: common.c:(.text+0x16a): undefined reference to `sdw_enable_stream'
s390-linux-ld: common.c:(.text+0x17c): undefined reference to `sdw_deprepare_stream'
s390-linux-ld: sound/soc/qcom/common.o: in function `qcom_snd_sdw_hw_free':
common.c:(.text+0x344): undefined reference to `sdw_disable_stream'
s390-linux-ld: common.c:(.text+0x34e): undefined reference to `sdw_deprepare_stream'
Fixes:
3bd975f3ae0a ("ASoC: qcom: sm8250: move some code to common")
Fixes:
9e3ecb5b1681 ("ASoC: qcom: sc7180: Add machine driver for sound card registration")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Banajit Goswami <bgoswami@quicinc.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Ajit Pandey <ajitp@codeaurora.org>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: stable@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Link: https://lore.kernel.org/r/20221015001228.18990-1-rdunlap@infradead.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Geert Uytterhoeven [Sun, 16 Oct 2022 08:33:50 +0000 (10:33 +0200)]
ASoC: codecs: tlv320adc3xxx: Wrap adc3xxx_i2c_remove() in __exit_p()
If CONFIG_SND_SOC_TLV320ADC3XXX=y:
`.exit.text' referenced in section `.data' of sound/soc/codecs/tlv320adc3xxx.o: defined in discarded section `.exit.text' of sound/soc/codecs/tlv320adc3xxx.o
Fix this by wrapping the adc3xxx_i2c_remove() pointer in __exit_p().
Fixes:
e9a3b57efd28fe88 ("ASoC: codec: tlv320adc3xxx: New codec driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/3225ba4cfe558d9380155e75385954dd21d4e7eb.1665909132.git.geert@linux-m68k.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Siarhei Volkau [Sun, 16 Oct 2022 13:26:45 +0000 (16:26 +0300)]
ASoC: codecs: jz4725b: fix capture selector naming
At the moment Capture source selector appears on Playback
tab in the alsamixer and has a senseless name.
Let's fix that.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-5-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Siarhei Volkau [Sun, 16 Oct 2022 13:26:44 +0000 (16:26 +0300)]
ASoC: codecs: jz4725b: use right control for Capture Volume
Line In Bypass control is used as Master Capture at the moment
this is completely incorrect.
Current control routed to Mixer instead of ADC, thus can't affect
Capture path. ADC control shall be used instead.
ADC volume control parameters are different, so the patch fixes that
as well. Manual says (16.6.3.2 Programmable input attenuation amplifier:
PGATM) that gain varies in range 0dB..22.5dB with 1.5dB step.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-4-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Siarhei Volkau [Sun, 16 Oct 2022 13:26:43 +0000 (16:26 +0300)]
ASoC: codecs: jz4725b: fix reported volume for Master ctl
DAC volume control is the Master Playback Volume at the moment
and it reports wrong levels in alsamixer and other alsa apps.
The patch fixes that, as stated in manual on the jz4725b SoC
(16.6.3.4 Programmable attenuation: GOD) the ctl range varies
from -22.5dB to 0dB with 1.5dB step.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-3-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Siarhei Volkau [Sun, 16 Oct 2022 13:26:42 +0000 (16:26 +0300)]
ASoC: codecs: jz4725b: add missed Line In power control bit
Line In path stayed powered off during capturing or
bypass to mixer.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-2-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Torvalds [Sun, 16 Oct 2022 22:36:24 +0000 (15:36 -0700)]
Linux 6.1-rc1
Linus Torvalds [Sun, 16 Oct 2022 22:27:07 +0000 (15:27 -0700)]
Merge tag 'random-6.1-rc1-for-linus' of git://git./linux/kernel/git/crng/random
Pull more random number generator updates from Jason Donenfeld:
"This time with some large scale treewide cleanups.
The intent of this pull is to clean up the way callers fetch random
integers. The current rules for doing this right are:
- If you want a secure or an insecure random u64, use get_random_u64()
- If you want a secure or an insecure random u32, use get_random_u32()
The old function prandom_u32() has been deprecated for a while
now and is just a wrapper around get_random_u32(). Same for
get_random_int().
- If you want a secure or an insecure random u16, use get_random_u16()
- If you want a secure or an insecure random u8, use get_random_u8()
- If you want secure or insecure random bytes, use get_random_bytes().
The old function prandom_bytes() has been deprecated for a while
now and has long been a wrapper around get_random_bytes()
- If you want a non-uniform random u32, u16, or u8 bounded by a
certain open interval maximum, use prandom_u32_max()
I say "non-uniform", because it doesn't do any rejection sampling
or divisions. Hence, it stays within the prandom_*() namespace, not
the get_random_*() namespace.
I'm currently investigating a "uniform" function for 6.2. We'll see
what comes of that.
By applying these rules uniformly, we get several benefits:
- By using prandom_u32_max() with an upper-bound that the compiler
can prove at compile-time is ≤65536 or ≤256, internally
get_random_u16() or get_random_u8() is used, which wastes fewer
batched random bytes, and hence has higher throughput.
- By using prandom_u32_max() instead of %, when the upper-bound is
not a constant, division is still avoided, because
prandom_u32_max() uses a faster multiplication-based trick instead.
- By using get_random_u16() or get_random_u8() in cases where the
return value is intended to indeed be a u16 or a u8, we waste fewer
batched random bytes, and hence have higher throughput.
This series was originally done by hand while I was on an airplane
without Internet. Later, Kees and I worked on retroactively figuring
out what could be done with Coccinelle and what had to be done
manually, and then we split things up based on that.
So while this touches a lot of files, the actual amount of code that's
hand fiddled is comfortably small"
* tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
prandom: remove unused functions
treewide: use get_random_bytes() when possible
treewide: use get_random_u32() when possible
treewide: use get_random_{u8,u16}() when possible, part 2
treewide: use get_random_{u8,u16}() when possible, part 1
treewide: use prandom_u32_max() when possible, part 2
treewide: use prandom_u32_max() when possible, part 1
Linus Torvalds [Sun, 16 Oct 2022 22:14:29 +0000 (15:14 -0700)]
Merge tag 'perf-tools-for-v6.1-2-2022-10-16' of git://git./linux/kernel/git/acme/linux
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Use BPF CO-RE (Compile Once, Run Everywhere) to support old kernels
when using bperf (perf BPF based counters) with cgroups.
- Support HiSilicon PCIe Performance Monitoring Unit (PMU), that
monitors bandwidth, latency, bus utilization and buffer occupancy.
Documented in Documentation/admin-guide/perf/hisi-pcie-pmu.rst.
- User space tasks can migrate between CPUs, so when tracing selected
CPUs, system-wide sideband is still needed, fix it in the setup of
Intel PT on hybrid systems.
- Fix metricgroups title message in 'perf list', it should state that
the metrics groups are to be used with the '-M' option, not '-e'.
- Sync the msr-index.h copy with the kernel sources, adding support for
using "AMD64_TSC_RATIO" in filter expressions in 'perf trace' as well
as decoding it when printing the MSR tracepoint arguments.
- Fix program header size and alignment when generating a JIT ELF in
'perf inject'.
- Add multiple new Intel PT 'perf test' entries, including a jitdump
one.
- Fix the 'perf test' entries for 'perf stat' CSV and JSON output when
running on PowerPC due to an invalid topology number in that arch.
- Fix the 'perf test' for arm_coresight failures on the ARM Juno
system.
- Fix the 'perf test' attr entry for PERF_FORMAT_LOST, adding this
option to the or expression expected in the intercepted
perf_event_open() syscall.
- Add missing condition flags ('hs', 'lo', 'vc', 'vs') for arm64 in the
'perf annotate' asm parser.
- Fix 'perf mem record -C' option processing, it was being chopped up
when preparing the underlying 'perf record -e mem-events' and thus
being ignored, requiring using '-- -C CPUs' as a workaround.
- Improvements and tidy ups for 'perf test' shell infra.
- Fix Intel PT information printing segfault in uClibc, where a NULL
format was being passed to fprintf.
* tag 'perf-tools-for-v6.1-2-2022-10-16' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (23 commits)
tools arch x86: Sync the msr-index.h copy with the kernel sources
perf auxtrace arm64: Add support for parsing HiSilicon PCIe Trace packet
perf auxtrace arm64: Add support for HiSilicon PCIe Tune and Trace device driver
perf auxtrace arm: Refactor event list iteration in auxtrace_record__init()
perf tests stat+json_output: Include sanity check for topology
perf tests stat+csv_output: Include sanity check for topology
perf intel-pt: Fix system_wide dummy event for hybrid
perf intel-pt: Fix segfault in intel_pt_print_info() with uClibc
perf test: Fix attr tests for PERF_FORMAT_LOST
perf test: test_intel_pt.sh: Add 9 tests
perf inject: Fix GEN_ELF_TEXT_OFFSET for jit
perf test: test_intel_pt.sh: Add jitdump test
perf test: test_intel_pt.sh: Tidy some alignment
perf test: test_intel_pt.sh: Print a message when skipping kernel tracing
perf test: test_intel_pt.sh: Tidy some perf record options
perf test: test_intel_pt.sh: Fix return checking again
perf: Skip and warn on unknown format 'configN' attrs
perf list: Fix metricgroups title message
perf mem: Fix -C option behavior for perf mem record
perf annotate: Add missing condition flags for arm64
...
Linus Torvalds [Sun, 16 Oct 2022 18:12:22 +0000 (11:12 -0700)]
Merge tag 'kbuild-fixes-v6.1' of git://git./linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y compile error for the
combination of Clang >= 14 and GAS <= 2.35.
- Drop vmlinux.bz2 from the rpm package as it just annoyingly increased
the package size.
- Fix modpost error under build environments using musl.
- Make *.ll files keep value names for easier debugging
- Fix single directory build
- Prevent RISC-V from selecting the broken DWARF5 support when Clang
and GAS are used together.
* tag 'kbuild-fixes-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
lib/Kconfig.debug: Add check for non-constant .{s,u}leb128 support to DWARF5
kbuild: fix single directory build
kbuild: add -fno-discard-value-names to cmd_cc_ll_c
scripts/clang-tools: Convert clang-tidy args to list
modpost: put modpost options before argument
kbuild: Stop including vmlinux.bz2 in the rpm's
Kconfig.debug: add toolchain checks for DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT
Kconfig.debug: simplify the dependency of DEBUG_INFO_DWARF4/5
Linus Torvalds [Sun, 16 Oct 2022 18:08:19 +0000 (11:08 -0700)]
Merge tag 'clk-for-linus' of git://git./linux/kernel/git/clk/linux
Pull more clk updates from Stephen Boyd:
"This is the final part of the clk patches for this merge window.
The clk rate range series needed another week to fully bake. Maxime
fixed the bug that broke clk notifiers and prevented this from being
included in the first pull request. He also added a unit test on top
to make sure it doesn't break so easily again. The majority of the
series fixes up how the clk_set_rate_*() APIs work, particularly
around when the rate constraints are dropped and how they move around
when reparenting clks. Overall it's a much needed improvement to the
clk rate range APIs that used to be pretty broken if you looked
sideways.
Beyond the core changes there are a few driver fixes for a compilation
issue or improper data causing clks to fail to register or have the
wrong parents. These are good to get in before the first -rc so that
the system actually boots on the affected devices"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (31 commits)
clk: tegra: Fix Tegra PWM parent clock
clk: at91: fix the build with binutils 2.27
clk: qcom: gcc-msm8660: Drop hardcoded fixed board clocks
clk: mediatek: clk-mux: Add .determine_rate() callback
clk: tests: Add tests for notifiers
clk: Update req_rate on __clk_recalc_rates()
clk: tests: Add missing test case for ranges
clk: qcom: clk-rcg2: Take clock boundaries into consideration for gfx3d
clk: Introduce the clk_hw_get_rate_range function
clk: Zero the clk_rate_request structure
clk: Stop forwarding clk_rate_requests to the parent
clk: Constify clk_has_parent()
clk: Introduce clk_core_has_parent()
clk: Switch from __clk_determine_rate to clk_core_round_rate_nolock
clk: Add our request boundaries in clk_core_init_rate_req
clk: Introduce clk_hw_init_rate_request()
clk: Move clk_core_init_rate_req() from clk_core_round_rate_nolock() to its caller
clk: Change clk_core_init_rate_req prototype
clk: Set req_rate on reparenting
clk: Take into account uncached clocks in clk_set_rate_range()
...
Linus Torvalds [Sun, 16 Oct 2022 18:01:40 +0000 (11:01 -0700)]
Merge tag '6.1-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull more cifs updates from Steve French:
- fix a regression in guest mounts to old servers
- improvements to directory leasing (caching directory entries safely
beyond the root directory)
- symlink improvement (reducing roundtrips needed to process symlinks)
- an lseek fix (to problem where some dir entries could be skipped)
- improved ioctl for returning more detailed information on directory
change notifications
- clarify multichannel interface query warning
- cleanup fix (for better aligning buffers using ALIGN and round_up)
- a compounding fix
- fix some uninitialized variable bugs found by Coverity and the kernel
test robot
* tag '6.1-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
smb3: improve SMB3 change notification support
cifs: lease key is uninitialized in two additional functions when smb1
cifs: lease key is uninitialized in smb1 paths
smb3: must initialize two ACL struct fields to zero
cifs: fix double-fault crash during ntlmssp
cifs: fix static checker warning
cifs: use ALIGN() and round_up() macros
cifs: find and use the dentry for cached non-root directories also
cifs: enable caching of directories for which a lease is held
cifs: prevent copying past input buffer boundaries
cifs: fix uninitialised var in smb2_compound_op()
cifs: improve symlink handling for smb2+
smb3: clarify multichannel warning
cifs: fix regression in very old smb1 mounts
cifs: fix skipping to incorrect offset in emit_cached_dirents
Tetsuo Handa [Sat, 15 Oct 2022 15:53:51 +0000 (00:53 +0900)]
Revert "cpumask: fix checking valid cpu range".
This reverts commit
78e5a3399421 ("cpumask: fix checking valid cpu range").
syzbot is hitting WARN_ON_ONCE(cpu >= nr_cpumask_bits) warning at
cpu_max_bits_warn() [1], for commit
78e5a3399421 ("cpumask: fix checking
valid cpu range") is broken. Obviously that patch hits WARN_ON_ONCE()
when e.g. reading /proc/cpuinfo because passing "cpu + 1" instead of
"cpu" will trivially hit cpu == nr_cpumask_bits condition.
Although syzbot found this problem in linux-next.git on 2022/09/27 [2],
this problem was not fixed immediately. As a result, that patch was
sent to linux.git before the patch author recognizes this problem, and
syzbot started failing to test changes in linux.git since 2022/10/10
[3].
Andrew Jones proposed a fix for x86 and riscv architectures [4]. But
[2] and [5] indicate that affected locations are not limited to arch
code. More delay before we find and fix affected locations, less tested
kernel (and more difficult to bisect and fix) before release.
We should have inspected and fixed basically all cpumask users before
applying that patch. We should not crash kernels in order to ask
existing cpumask users to update their code, even if limited to
CONFIG_DEBUG_PER_CPU_MAPS=y case.
Link: https://syzkaller.appspot.com/bug?extid=d0fd2bf0dd6da72496dd
Link: https://syzkaller.appspot.com/bug?extid=21da700f3c9f0bc40150
Link: https://syzkaller.appspot.com/bug?extid=51a652e2d24d53e75734
Link: https://lkml.kernel.org/r/20221014155845.1986223-1-ajones@ventanamicro.com
Link: https://syzkaller.appspot.com/bug?extid=4d46c43d81c3bd155060
Reported-by: Andrew Jones <ajones@ventanamicro.com>
Reported-by: syzbot+d0fd2bf0dd6da72496dd@syzkaller.appspotmail.com
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Yury Norov <yury.norov@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nathan Chancellor [Fri, 14 Oct 2022 20:42:11 +0000 (13:42 -0700)]
lib/Kconfig.debug: Add check for non-constant .{s,u}leb128 support to DWARF5
When building with a RISC-V kernel with DWARF5 debug info using clang
and the GNU assembler, several instances of the following error appear:
/tmp/vgettimeofday-48aa35.s:2963: Error: non-constant .uleb128 is not supported
Dumping the .s file reveals these .uleb128 directives come from
.debug_loc and .debug_ranges:
.Ldebug_loc0:
.byte 4 # DW_LLE_offset_pair
.uleb128 .Lfunc_begin0-.Lfunc_begin0 # starting offset
.uleb128 .Ltmp1-.Lfunc_begin0 # ending offset
.byte 1 # Loc expr size
.byte 90 # DW_OP_reg10
.byte 0 # DW_LLE_end_of_list
.Ldebug_ranges0:
.byte 4 # DW_RLE_offset_pair
.uleb128 .Ltmp6-.Lfunc_begin0 # starting offset
.uleb128 .Ltmp27-.Lfunc_begin0 # ending offset
.byte 4 # DW_RLE_offset_pair
.uleb128 .Ltmp28-.Lfunc_begin0 # starting offset
.uleb128 .Ltmp30-.Lfunc_begin0 # ending offset
.byte 0 # DW_RLE_end_of_list
There is an outstanding binutils issue to support a non-constant operand
to .sleb128 and .uleb128 in GAS for RISC-V but there does not appear to
be any movement on it, due to concerns over how it would work with
linker relaxation.
To avoid these build errors, prevent DWARF5 from being selected when
using clang and an assembler that does not have support for these symbol
deltas, which can be easily checked in Kconfig with as-instr plus the
small test program from the dwz test suite from the binutils issue.
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=27215
Link: https://github.com/ClangBuiltLinux/linux/issues/1719
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Masahiro Yamada [Fri, 14 Oct 2022 20:18:11 +0000 (05:18 +0900)]
kbuild: fix single directory build
Commit
f110e5a250e3 ("kbuild: refactor single builds of *.ko") was wrong.
KBUILD_MODULES _is_ needed for single builds.
Otherwise, "make foo/bar/baz/" does not build module objects at all.
Fixes:
f110e5a250e3 ("kbuild: refactor single builds of *.ko")
Reported-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: David Sterba <dsterba@suse.com>
Linus Torvalds [Sun, 16 Oct 2022 00:05:07 +0000 (17:05 -0700)]
Merge tag 'slab-for-6.1-rc1-hotfix' of git://git./linux/kernel/git/vbabka/slab
Pull slab hotfix from Vlastimil Babka:
"A single fix for the common-kmalloc series, for warnings on mips and
sparc64 reported by Guenter Roeck"
* tag 'slab-for-6.1-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
mm/slab: use kmalloc_node() for off slab freelist_idx_t array allocation
Linus Torvalds [Sat, 15 Oct 2022 23:47:33 +0000 (16:47 -0700)]
Merge tag 'for-linus' of https://github.com/openrisc/linux
Pull OpenRISC updates from Stafford Horne:
"I have relocated to London so not much work from me while I get
settled.
Still, OpenRISC picked up two patches in this window:
- Fix for kernel page table walking from Jann Horn
- MAINTAINER entry cleanup from Palmer Dabbelt"
* tag 'for-linus' of https://github.com/openrisc/linux:
MAINTAINERS: git://github -> https://github.com for openrisc
openrisc: Fix pagewalk usage in arch_dma_{clear, set}_uncached
Linus Torvalds [Sat, 15 Oct 2022 23:36:38 +0000 (16:36 -0700)]
Merge tag 'pci-v6.1-fixes-1' of git://git./linux/kernel/git/helgaas/pci
Pull pci fix from Bjorn Helgaas:
"Revert the attempt to distribute spare resources to unconfigured
hotplug bridges at boot time.
This fixed some dock hot-add scenarios, but Jonathan Cameron reported
that it broke a topology with a multi-function device where one
function was a Switch Upstream Port and the other was an Endpoint"
* tag 'pci-v6.1-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: Distribute available resources for root buses, too"
Hyeonggon Yoo [Sat, 15 Oct 2022 04:34:29 +0000 (13:34 +0900)]
mm/slab: use kmalloc_node() for off slab freelist_idx_t array allocation
After commit
d6a71648dbc0 ("mm/slab: kmalloc: pass requests larger than
order-1 page to page allocator"), SLAB passes large ( > PAGE_SIZE * 2)
requests to buddy like SLUB does.
SLAB has been using kmalloc caches to allocate freelist_idx_t array for
off slab caches. But after the commit, freelist_size can be bigger than
KMALLOC_MAX_CACHE_SIZE.
Instead of using pointer to kmalloc cache, use kmalloc_node() and only
check if the kmalloc cache is off slab during calculate_slab_order().
If freelist_size > KMALLOC_MAX_CACHE_SIZE, no looping condition happens
as it allocates freelist_idx_t array directly from buddy.
Link: https://lore.kernel.org/all/20221014205818.GA1428667@roeck-us.net/
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Fixes:
d6a71648dbc0 ("mm/slab: kmalloc: pass requests larger than order-1 page to page allocator")
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Palmer Dabbelt [Thu, 13 Oct 2022 21:46:37 +0000 (14:46 -0700)]
MAINTAINERS: git://github -> https://github.com for openrisc
Github deprecated the git:// links about a year ago, so let's move to
the https:// URLs instead.
Reported-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://github.blog/2021-09-01-improving-git-protocol-security-github/
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Steve French [Sat, 15 Oct 2022 05:43:22 +0000 (00:43 -0500)]
smb3: improve SMB3 change notification support
Change notification is a commonly supported feature by most servers,
but the current ioctl to request notification when a directory is
changed does not return the information about what changed
(even though it is returned by the server in the SMB3 change
notify response), it simply returns when there is a change.
This ioctl improves upon CIFS_IOC_NOTIFY by returning the notify
information structure which includes the name of the file(s) that
changed and why. See MS-SMB2 2.2.35 for details on the individual
filter flags and the file_notify_information structure returned.
To use this simply pass in the following (with enough space
to fit at least one file_notify_information structure)
struct __attribute__((__packed__)) smb3_notify {
uint32_t completion_filter;
bool watch_tree;
uint32_t data_len;
uint8_t data[];
} __packed;
using CIFS_IOC_NOTIFY_INFO 0xc009cf0b
or equivalently _IOWR(CIFS_IOCTL_MAGIC, 11, struct smb3_notify_info)
The ioctl will block until the server detects a change to that
directory or its subdirectories (if watch_tree is set).
Acked-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Steve French [Sat, 15 Oct 2022 01:00:32 +0000 (20:00 -0500)]
cifs: lease key is uninitialized in two additional functions when smb1
cifs_open and _cifsFileInfo_put also end up with lease_key uninitialized
in smb1 mounts. It is cleaner to set lease key to zero in these
places where leases are not supported (smb1 can not return lease keys
so the field was uninitialized).
Addresses-Coverity:
1514207 ("Uninitialized scalar variable")
Addresses-Coverity:
1514331 ("Uninitialized scalar variable")
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Steve French [Sat, 15 Oct 2022 00:18:32 +0000 (19:18 -0500)]
cifs: lease key is uninitialized in smb1 paths
It is cleaner to set lease key to zero in the places where leases are not
supported (smb1 can not return lease keys so the field was uninitialized).
Addresses-Coverity:
1513994 ("Uninitialized scalar variable")
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Steve French [Fri, 14 Oct 2022 23:50:20 +0000 (18:50 -0500)]
smb3: must initialize two ACL struct fields to zero
Coverity spotted that we were not initalizing Stbz1 and Stbz2 to
zero in create_sd_buf.
Addresses-Coverity:
1513848 ("Uninitialized scalar variable")
Cc: <stable@vger.kernel.org>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Paulo Alcantara [Fri, 14 Oct 2022 20:14:54 +0000 (17:14 -0300)]
cifs: fix double-fault crash during ntlmssp
The crash occurred because we were calling memzero_explicit() on an
already freed sess_data::iov[1] (ntlmsspblob) in sess_free_buffer().
Fix this by not calling memzero_explicit() on sess_data::iov[1] as
it's already by handled by callers.
Fixes:
a4e430c8c8ba ("cifs: replace kfree() with kfree_sensitive() for sensitive data")
Reviewed-by: Enzo Matsumiya <ematsumiya@suse.de>
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Arnaldo Carvalho de Melo [Fri, 7 Aug 2020 11:45:47 +0000 (08:45 -0300)]
tools arch x86: Sync the msr-index.h copy with the kernel sources
To pick up the changes in:
b8d1d163604bd1e6 ("x86/apic: Don't disable x2APIC if locked")
ca5b7c0d9621702e ("perf/x86/amd/lbr: Add LbrExtV2 branch record support")
Addressing these tools/perf build warnings:
diff -u tools/arch/x86/include/asm/msr-index.h arch/x86/include/asm/msr-index.h
Warning: Kernel ABI header at 'tools/arch/x86/include/asm/msr-index.h' differs from latest version at 'arch/x86/include/asm/msr-index.h'
That makes the beautification scripts to pick some new entries:
$ tools/perf/trace/beauty/tracepoints/x86_msr.sh > before
$ cp arch/x86/include/asm/msr-index.h tools/arch/x86/include/asm/msr-index.h
$ tools/perf/trace/beauty/tracepoints/x86_msr.sh > after
$ diff -u before after
--- before 2022-10-14 18:06:34.
294561729 -0300
+++ after 2022-10-14 18:06:41.
285744044 -0300
@@ -264,6 +264,7 @@
[0xc0000102 - x86_64_specific_MSRs_offset] = "KERNEL_GS_BASE",
[0xc0000103 - x86_64_specific_MSRs_offset] = "TSC_AUX",
[0xc0000104 - x86_64_specific_MSRs_offset] = "AMD64_TSC_RATIO",
+ [0xc000010e - x86_64_specific_MSRs_offset] = "AMD64_LBR_SELECT",
[0xc000010f - x86_64_specific_MSRs_offset] = "AMD_DBG_EXTN_CFG",
[0xc0000300 - x86_64_specific_MSRs_offset] = "AMD64_PERF_CNTR_GLOBAL_STATUS",
[0xc0000301 - x86_64_specific_MSRs_offset] = "AMD64_PERF_CNTR_GLOBAL_CTL",
$
Now one can trace systemwide asking to see backtraces to where that MSR
is being read/written, see this example with a previous update:
# perf trace -e msr:*_msr/max-stack=32/ --filter="msr>=IA32_U_CET && msr<=IA32_INT_SSP_TAB"
^C#
If we use -v (verbose mode) we can see what it does behind the scenes:
# perf trace -v -e msr:*_msr/max-stack=32/ --filter="msr>=IA32_U_CET && msr<=IA32_INT_SSP_TAB"
Using CPUID AuthenticAMD-25-21-0
0x6a0
0x6a8
New filter for msr:read_msr: (msr>=0x6a0 && msr<=0x6a8) && (common_pid != 597499 && common_pid != 3313)
0x6a0
0x6a8
New filter for msr:write_msr: (msr>=0x6a0 && msr<=0x6a8) && (common_pid != 597499 && common_pid != 3313)
mmap size
528384B
^C#
Example with a frequent msr:
# perf trace -v -e msr:*_msr/max-stack=32/ --filter="msr==IA32_SPEC_CTRL" --max-events 2
Using CPUID AuthenticAMD-25-21-0
0x48
New filter for msr:read_msr: (msr==0x48) && (common_pid !=
2612129 && common_pid != 3841)
0x48
New filter for msr:write_msr: (msr==0x48) && (common_pid !=
2612129 && common_pid != 3841)
mmap size
528384B
Looking at the vmlinux_path (8 entries long)
symsrc__init: build id mismatch for vmlinux.
Using /proc/kcore for kernel data
Using /proc/kallsyms for symbols
0.000 Timer/
2525383 msr:write_msr(msr: IA32_SPEC_CTRL, val: 6)
do_trace_write_msr ([kernel.kallsyms])
do_trace_write_msr ([kernel.kallsyms])
__switch_to_xtra ([kernel.kallsyms])
__switch_to ([kernel.kallsyms])
__schedule ([kernel.kallsyms])
schedule ([kernel.kallsyms])
futex_wait_queue_me ([kernel.kallsyms])
futex_wait ([kernel.kallsyms])
do_futex ([kernel.kallsyms])
__x64_sys_futex ([kernel.kallsyms])
do_syscall_64 ([kernel.kallsyms])
entry_SYSCALL_64_after_hwframe ([kernel.kallsyms])
__futex_abstimed_wait_common64 (/usr/lib64/libpthread-2.33.so)
0.030 :0/0 msr:write_msr(msr: IA32_SPEC_CTRL, val: 2)
do_trace_write_msr ([kernel.kallsyms])
do_trace_write_msr ([kernel.kallsyms])
__switch_to_xtra ([kernel.kallsyms])
__switch_to ([kernel.kallsyms])
__schedule ([kernel.kallsyms])
schedule_idle ([kernel.kallsyms])
do_idle ([kernel.kallsyms])
cpu_startup_entry ([kernel.kallsyms])
secondary_startup_64_no_verify ([kernel.kallsyms])
#
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandipan Das <sandipan.das@amd.com>
Link: https://lore.kernel.org/lkml/Y0nQkz2TUJxwfXJd@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Qi Liu [Tue, 27 Sep 2022 08:14:00 +0000 (16:14 +0800)]
perf auxtrace arm64: Add support for parsing HiSilicon PCIe Trace packet
Add support for using 'perf report --dump-raw-trace' to parse PTT packet.
Example usage:
Output will contain raw PTT data and its textual representation, such
as (8DW format):
0 0 0x5810 [0x30]: PERF_RECORD_AUXTRACE size: 0x400000 offset: 0
ref: 0xa5d50c725 idx: 0 tid: -1 cpu: 0
.
. ... HISI PTT data: size
4194304 bytes
.
00000000: 00 00 00 00 Prefix
.
00000004: 08 20 00 60 Header DW0
.
00000008: ff 02 00 01 Header DW1
.
0000000c: 20 08 00 00 Header DW2
.
00000010: 10 e7 44 ab Header DW3
.
00000014: 2a a8 1e 01 Time
.
00000020: 00 00 00 00 Prefix
.
00000024: 01 00 00 60 Header DW0
.
00000028: 0f 1e 00 01 Header DW1
.
0000002c: 04 00 00 00 Header DW2
.
00000030: 40 00 81 02 Header DW3
.
00000034: ee 02 00 00 Time
....
This patch only add basic parsing support according to the definition of
the PTT packet described in Documentation/trace/hisi-ptt.rst. And the
fields of each packet can be further decoded following the PCIe Spec's
definition of TLP packet.
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@arm.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Jonathan Cameron <jonathan.cameron@huawei.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qi Liu <liuqi6124@gmail.com>
Cc: Shameerali Kolothum Thodi <shameerali.kolothum.thodi@huawei.com>
Cc: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Zeng Prime <prime.zeng@huawei.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: linuxarm@huawei.com
Link: https://lore.kernel.org/r/20220927081400.14364-4-yangyicong@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Qi Liu [Tue, 27 Sep 2022 08:13:59 +0000 (16:13 +0800)]
perf auxtrace arm64: Add support for HiSilicon PCIe Tune and Trace device driver
HiSilicon PCIe tune and trace device (PTT) could dynamically tune the
PCIe link's events, and trace the TLP headers).
This patch add support for PTT device in perf tool, so users could use
'perf record' to get TLP headers trace data.
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Acked-by: John Garry <john.garry@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jonathan Cameron <jonathan.cameron@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qi Liu <liuqi6124@gmail.com>
Cc: Shameerali Kolothum Thodi <shameerali.kolothum.thodi@huawei.com>
Cc: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Zeng Prime <prime.zeng@huawei.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: linuxarm@huawei.com
Link: https://lore.kernel.org/r/20220927081400.14364-3-yangyicong@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Qi Liu [Tue, 27 Sep 2022 08:13:58 +0000 (16:13 +0800)]
perf auxtrace arm: Refactor event list iteration in auxtrace_record__init()
Add find_pmu_for_event() and use to simplify logic in
auxtrace_record_init(). find_pmu_for_event() will be reused in
subsequent patches.
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qi Liu <liuqi6124@gmail.com>
Cc: Shameerali Kolothum Thodi <shameerali.kolothum.thodi@huawei.com>
Cc: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Zeng Prime <prime.zeng@huawei.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: linuxarm@huawei.com
Link: https://lore.kernel.org/r/20220927081400.14364-2-yangyicong@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Athira Rajeev [Thu, 6 Oct 2022 15:51:49 +0000 (21:21 +0530)]
perf tests stat+json_output: Include sanity check for topology
Testcase stat+json_output.sh fails in powerpc:
86: perf stat JSON output linter : FAILED!
The testcase "stat+json_output.sh" verifies perf stat JSON output. The
test covers aggregation modes like per-socket, per-core, per-die, -A
(no_aggr mode) along with few other tests. It counts expected fields for
various commands. For example say -A (i.e, AGGR_NONE mode), expects 7
fields in the output having "CPU" as first field. Same way, for
per-socket, it expects the first field in result to point to socket id.
The testcases compares the result with expected count.
The values for socket, die, core and cpu are fetched from topology
directory:
/sys/devices/system/cpu/cpu*/topology.
For example, socket value is fetched from "physical_package_id" file of
topology directory. (cpu__get_topology_int() in util/cpumap.c)
If a platform fails to fetch the topology information, values will be
set to -1. For example, incase of pSeries platform of powerpc, value for
"physical_package_id" is restricted and not exposed. So, -1 will be
assigned.
Perf code has a checks for valid cpu id in "aggr_printout"
(stat-display.c), which displays the fields. So, in cases where topology
values not exposed, first field of the output displaying will be empty.
This cause the testcase to fail, as it counts number of fields in the
output.
Incase of -A (AGGR_NONE mode,), testcase expects 7 fields in the output,
becos of -1 value obtained from topology files for some, only 6 fields
are printed. Hence a testcase failure reported due to mismatch in number
of fields in the output.
Patch here adds a sanity check in the testcase for topology. Check will
help to skip the test if -1 value found.
Fixes:
0c343af2a2f82844 ("perf test: JSON format checking")
Reported-by: Disha Goel <disgoel@linux.vnet.ibm.com>
Suggested-by: Ian Rogers <irogers@google.com>
Suggested-by: James Clark <james.clark@arm.com>
Signed-off-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Claire Jensen <cjense@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nageswara R Sastry <rnsastry@linux.ibm.com>
Link: https://lore.kernel.org/r/20221006155149.67205-2-atrajeev@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Athira Rajeev [Thu, 6 Oct 2022 15:51:48 +0000 (21:21 +0530)]
perf tests stat+csv_output: Include sanity check for topology
Testcase stat+csv_output.sh fails in powerpc:
84: perf stat CSV output linter: FAILED!
The testcase "stat+csv_output.sh" verifies perf stat CSV output. The
test covers aggregation modes like per-socket, per-core, per-die, -A
(no_aggr mode) along with few other tests. It counts expected fields for
various commands. For example say -A (i.e, AGGR_NONE mode), expects 7
fields in the output having "CPU" as first field. Same way, for
per-socket, it expects the first field in result to point to socket id.
The testcases compares the result with expected count.
The values for socket, die, core and cpu are fetched from topology
directory:
/sys/devices/system/cpu/cpu*/topology.
For example, socket value is fetched from "physical_package_id" file of
topology directory. (cpu__get_topology_int() in util/cpumap.c)
If a platform fails to fetch the topology information, values will be
set to -1. For example, incase of pSeries platform of powerpc, value for
"physical_package_id" is restricted and not exposed. So, -1 will be
assigned.
Perf code has a checks for valid cpu id in "aggr_printout"
(stat-display.c), which displays the fields. So, in cases where topology
values not exposed, first field of the output displaying will be empty.
This cause the testcase to fail, as it counts number of fields in the
output.
Incase of -A (AGGR_NONE mode,), testcase expects 7 fields in the output,
becos of -1 value obtained from topology files for some, only 6 fields
are printed. Hence a testcase failure reported due to mismatch in number
of fields in the output.
Patch here adds a sanity check in the testcase for topology. Check will
help to skip the test if -1 value found.
Fixes:
7473ee56dbc91c98 ("perf test: Add checking for perf stat CSV output.")
Reported-by: Disha Goel <disgoel@linux.vnet.ibm.com>
Suggested-by: Ian Rogers <irogers@google.com>
Suggested-by: James Clark <james.clark@arm.com>
Signed-off-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Claire Jensen <cjense@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nageswara R Sastry <rnsastry@linux.ibm.com>
Link: https://lore.kernel.org/r/20221006155149.67205-1-atrajeev@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adrian Hunter [Wed, 12 Oct 2022 08:22:59 +0000 (11:22 +0300)]
perf intel-pt: Fix system_wide dummy event for hybrid
User space tasks can migrate between CPUs, so when tracing selected CPUs,
system-wide sideband is still needed, however evlist->core.has_user_cpus
is not set in the hybrid case, so check the target cpu_list instead.
Fixes:
7d189cadbeebc778 ("perf intel-pt: Track sideband system-wide when needed")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221012082259.22394-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adrian Hunter [Wed, 12 Oct 2022 08:22:58 +0000 (11:22 +0300)]
perf intel-pt: Fix segfault in intel_pt_print_info() with uClibc
uClibc segfaulted because NULL was passed as the format to fprintf().
That happened because one of the format strings was missing and
intel_pt_print_info() didn't check that before calling fprintf().
Add the missing format string, and check format is not NULL before calling
fprintf().
Fixes:
11fa7cb86b56d361 ("perf tools: Pass Intel PT information for decoding MTC and CYC")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221012082259.22394-2-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
James Clark [Wed, 12 Oct 2022 09:46:32 +0000 (10:46 +0100)]
perf test: Fix attr tests for PERF_FORMAT_LOST
Since PERF_FORMAT_LOST was added, the default read format has that bit
set, so add it to the tests. Keep the old value as well so that the test
still passes on older kernels.
This fixes the following failure:
expected read_format=0|4, got 20
FAILED './tests/attr/test-record-C0' - match failure
Fixes:
85b425f31c8866e0 ("perf record: Set PERF_FORMAT_LOST by default")
Signed-off-by: James Clark <james.clark@arm.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20221012094633.21669-2-james.clark@arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ammy Yi [Fri, 14 Oct 2022 17:09:05 +0000 (20:09 +0300)]
perf test: test_intel_pt.sh: Add 9 tests
Add tests:
Test with MTC and TSC disabled
Test with branches disabled
Test with/without CYC
Test recording with sample mode
Test with kernel trace
Test virtual LBR
Test power events
Test with TNT packets disabled
Test with event_trace
These tests mostly check that perf record works with the corresponding
Intel PT config terms, sometimes also checking that certain packets do or
do not appear in the resulting trace as appropriate.
The "Test virtual LBR" is slightly trickier, using a Python script to
check that branch stacks are actually synthesized.
Signed-off-by: Ammy Yi <ammy.yi@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20221014170905.64069-8-adrian.hunter@intel.com
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adrian Hunter [Fri, 14 Oct 2022 17:09:04 +0000 (20:09 +0300)]
perf inject: Fix GEN_ELF_TEXT_OFFSET for jit
When a program header was added, it moved the text section but
GEN_ELF_TEXT_OFFSET was not updated.
Fix by adding the program header size and aligning.
Fixes:
babd04386b1df8c3 ("perf jit: Include program header in ELF files")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Lieven Hey <lieven.hey@kdab.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20221014170905.64069-7-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adrian Hunter [Fri, 14 Oct 2022 17:09:03 +0000 (20:09 +0300)]
perf test: test_intel_pt.sh: Add jitdump test
Add a test for decoding self-modifying code using a jitdump file.
The test creates a workload that uses self-modifying code and generates its
own jitdump file. The result is processed with perf inject --jit and
checked for decoding errors.
Note the test will fail without patch "perf inject: Fix GEN_ELF_TEXT_OFFSET
for jit" applied.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20221014170905.64069-6-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adrian Hunter [Fri, 14 Oct 2022 17:09:02 +0000 (20:09 +0300)]
perf test: test_intel_pt.sh: Tidy some alignment
Tidy alignment of test function lines to make them more readable.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20221014170905.64069-5-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adrian Hunter [Fri, 14 Oct 2022 17:09:01 +0000 (20:09 +0300)]
perf test: test_intel_pt.sh: Print a message when skipping kernel tracing
Messages display with the perf test -v option. Add a message to show when
skipping a test because the user cannot do kernel tracing.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20221014170905.64069-4-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adrian Hunter [Fri, 14 Oct 2022 17:09:00 +0000 (20:09 +0300)]
perf test: test_intel_pt.sh: Tidy some perf record options
When not decoding, the options "-B -N --no-bpf-event" speed up perf record.
Make a common function for them.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20221014170905.64069-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adrian Hunter [Fri, 14 Oct 2022 17:08:59 +0000 (20:08 +0300)]
perf test: test_intel_pt.sh: Fix return checking again
count_result() does not always reset ret=0 which means the value can spill
into the next test result.
Fix by explicitly setting it to zero between tests.
Committer testing:
# perf test "Miscellaneous Intel PT testing"
110: Miscellaneous Intel PT testing : Ok
#
Tested as well with:
# perf test -v "Miscellaneous Intel PT testing"
Fixes:
fd9b45e39cfaf885 ("perf test: test_intel_pt.sh: Fix return checking")
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20221014170905.64069-2-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Linus Torvalds [Sat, 15 Oct 2022 01:41:41 +0000 (18:41 -0700)]
Merge tag 'libnvdimm-for-6.1' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull nvdimm updates from Dan Williams:
"Some small cleanups and fixes in and around the nvdimm subsystem. The
most significant change is a regression fix for nvdimm namespace
(volume) creation when the namespace size is smaller than 2MB/
Summary:
- Fix nvdimm namespace creation on platforms that do not publish
associated 'DIMM' metadata for a persistent memory region.
- Miscellaneous fixes and cleanups"
* tag 'libnvdimm-for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
ACPI: HMAT: Release platform device in case of platform_device_add_data() fails
dax: Remove usage of the deprecated ida_simple_xxx API
libnvdimm/region: Allow setting align attribute on regions without mappings
nvdimm/namespace: Fix comment typo
nvdimm: make __nvdimm_security_overwrite_query static
nvdimm/region: Fix kernel-doc
nvdimm/namespace: drop unneeded temporary variable in size_store()
nvdimm/namespace: return uuid_null only once in nd_dev_to_uuid()
Linus Torvalds [Sat, 15 Oct 2022 01:36:42 +0000 (18:36 -0700)]
Merge tag 'rtc-6.1' of git://git./linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"A great rework of the isl12022 driver makes up the bulk of the
changes. There is also an important fix for CMOS and then the usual
small fixes:
- switch to devm_clk_get_enabled() where relevant
- cmos: event handler registration fix
- isl12022: code improvements"
* tag 'rtc-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: rv3028: Fix codestyle errors
rtc: cmos: Fix event handler registration ordering issue
rtc: k3: Use devm_clk_get_enabled() helper
rtc: jz4740: Use devm_clk_get_enabled() helper
rtc: mpfs: Use devm_clk_get_enabled() helper
rtc: ds1685: Fix spelling of function name in comment block
rtc: isl12022: switch to using regmap API
rtc: isl12022: drop redundant write to HR register
rtc: isl12022: use dev_set_drvdata() instead of i2c_set_clientdata()
rtc: isl12022: use %ptR
rtc: isl12022: simplify some expressions
rtc: isl12022: drop a dev_info()
rtc: isl12022: specify range_min and range_max
rtc: isl12022: stop using deprecated devm_rtc_device_register()
rtc: stmp3xxx: Add failure handling for stmp3xxx_wdt_register()
rtc: mxc: Use devm_clk_get_enabled() helper
rtc: gamecube: Always reset HW_SRNPROT after read
rtc: k3: detect SoC to determine erratum fix
rtc: k3: wait until the unlock field is not zero
rtc: mpfs: Remove printing of stray CR
Linus Torvalds [Sat, 15 Oct 2022 01:31:28 +0000 (18:31 -0700)]
Merge tag 'i3c/for-6.1' of git://git./linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"Not much this cycle, only two fixes for a rare event"
- fix device reattach issues"
* tag 'i3c/for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: Remove the wrong place of reattach.
i3c: master: Free the old_dyn_addr when reattach.
Linus Torvalds [Sat, 15 Oct 2022 01:23:23 +0000 (18:23 -0700)]
Merge tag 'for-linus-6.1-rc1' of git://git./linux/kernel/git/rw/ubifs
Pull UBI and UBIFS updates from Richard Weinberger:
"UBI:
- Use bitmap API to allocate bitmaps
- New attach mode, disable_fm, to attach without fastmap
- Fixes for various typos in comments
UBIFS:
- Fix for a deadlock when setting xattrs for encrypted file
- Fix for an assertion failures when truncating encrypted files
- Fixes for various typos in comments"
* tag 'for-linus-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: fastmap: Add fastmap control support for 'UBI_IOCATT' ioctl
ubi: fastmap: Use the bitmap API to allocate bitmaps
ubifs: Fix AA deadlock when setting xattr for encrypted file
ubifs: Fix UBIFS ro fail due to truncate in the encrypted directory
mtd: ubi: drop unexpected word 'a' in comments
ubi: block: Fix typos in comments
ubi: fastmap: Fix typo in comments
ubi: Fix repeated words in comments
ubi: ubi-media.h: Fix comment typo
ubi: block: Remove in vain semicolon
ubifs: Fix ubifs_check_dir_empty() kernel-doc comment
Linus Torvalds [Sat, 15 Oct 2022 01:14:48 +0000 (18:14 -0700)]
Merge tag 'for-linus-6.1-rc1' of git://git./linux/kernel/git/uml/linux
Pull UML updates from Richard Weinberger:
- Move to strscpy()
- Improve panic notifiers
- Fix NR_CPUS usage
- Fixes for various comments
- Fixes for virtio driver
* tag 'for-linus-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux:
uml: Remove the initialization of statics to 0
um: Do not initialise statics to 0.
um: Fix comment typo
um: Improve panic notifiers consistency and ordering
um: remove unused reactivate_chan() declaration
um: mmaper: add __exit annotations to module exit funcs
um: virt-pci: add __init/__exit annotations to module init/exit funcs
hostfs: move from strlcpy with unused retval to strscpy
um: move from strlcpy with unused retval to strscpy
um: increase default virtual physical memory to 64 MiB
UM: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
um: read multiple msg from virtio slave request fd
Linus Torvalds [Fri, 14 Oct 2022 20:47:42 +0000 (13:47 -0700)]
Merge tag 'asm-generic-fixes-6.1-1' of git://git./linux/kernel/git/arnd/asm-generic
Pull asm-generic fix from Arnd Bergmann:
"A last-minute arch/alpha regression fix: the previous asm-generic
branch contained a new regression from a typo"
* tag 'asm-generic-fixes-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
alpha: fix marvel_ioread8 build regression
Linus Torvalds [Fri, 14 Oct 2022 20:44:53 +0000 (13:44 -0700)]
Merge tag 'arm-fixes-6.1-1' of git://git./linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"These are three fixes for build warnings that came in during the merge
window"
* tag 'arm-fixes-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: mmp: Make some symbols static
ARM: spear6xx: Staticize few definitions
clk: spear: Move prototype to accessible header
Stephen Boyd [Fri, 14 Oct 2022 20:44:44 +0000 (13:44 -0700)]
Merge branch 'clk-rate-range' into clk-next
- Various clk rate range fixes
- Drop clk rate range constraints on clk_put() (redux)
* clk-rate-range: (28 commits)
clk: mediatek: clk-mux: Add .determine_rate() callback
clk: tests: Add tests for notifiers
clk: Update req_rate on __clk_recalc_rates()
clk: tests: Add missing test case for ranges
clk: qcom: clk-rcg2: Take clock boundaries into consideration for gfx3d
clk: Introduce the clk_hw_get_rate_range function
clk: Zero the clk_rate_request structure
clk: Stop forwarding clk_rate_requests to the parent
clk: Constify clk_has_parent()
clk: Introduce clk_core_has_parent()
clk: Switch from __clk_determine_rate to clk_core_round_rate_nolock
clk: Add our request boundaries in clk_core_init_rate_req
clk: Introduce clk_hw_init_rate_request()
clk: Move clk_core_init_rate_req() from clk_core_round_rate_nolock() to its caller
clk: Change clk_core_init_rate_req prototype
clk: Set req_rate on reparenting
clk: Take into account uncached clocks in clk_set_rate_range()
clk: tests: Add some tests for orphan with multiple parents
clk: tests: Add tests for mux with multiple parents
clk: tests: Add tests for single parent mux
...
Jon Hunter [Mon, 10 Oct 2022 10:00:46 +0000 (11:00 +0100)]
clk: tegra: Fix Tegra PWM parent clock
Commit
8c193f4714df ("pwm: tegra: Optimize period calculation") updated
the period calculation in the Tegra PWM driver and now returns an error
if the period requested is less than minimum period supported. This is
breaking PWM support on various Tegra platforms. For example, on the
Tegra210 Jetson Nano platform this is breaking the PWM fan support and
probing the PWM fan driver now fails ...
pwm-fan pwm-fan: Failed to configure PWM: -22
pwm-fan: probe of pwm-fan failed with error -22
The problem is that the default parent clock for the PWM on Tegra210 is
a 32kHz clock and is unable to support the requested PWM period.
Fix PWM support on Tegra20, Tegra30, Tegra114, Tegra124 and Tegra210 by
updating the parent clock for the PWM to be the PLL_P.
Fixes:
8c193f4714df ("pwm: tegra: Optimize period calculation")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # TF101 T20
Tested-by: Antoni Aloy Torrens <aaloytorrens@gmail.com> # TF101 T20
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # TF201 T30
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # TF700T T3
Link: https://lore.kernel.org/r/20221010100046.6477-1-jonathanh@nvidia.com
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Kefeng Wang [Wed, 12 Oct 2022 03:06:35 +0000 (11:06 +0800)]
clk: at91: fix the build with binutils 2.27
There is an issue when build with older versions of binutils 2.27.0,
arch/arm/mach-at91/pm_suspend.S: Assembler messages:
arch/arm/mach-at91/pm_suspend.S:1086: Error: garbage following instruction -- `ldr tmp1,=0x00020010UL'
Use UL() macro to fix the issue in assembly file.
Fixes:
4fd36e458392 ("ARM: at91: pm: add plla disable/enable support for sam9x60")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Link: https://lore.kernel.org/r/20221012030635.13140-1-wangkefeng.wang@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Linus Walleij [Thu, 13 Oct 2022 14:07:45 +0000 (16:07 +0200)]
clk: qcom: gcc-msm8660: Drop hardcoded fixed board clocks
These two clocks are now registered in the device tree as fixed clocks,
causing a regression in the driver as the clock already exists with
e.g. the name "pxo_board" as the MSM8660 GCC driver probes.
Fix this by just not hard-coding this anymore and everything works
like a charm.
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes:
baecbda52933 ("ARM: dts: qcom: msm8660: fix node names for fixed clocks")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221013140745.7801-1-linus.walleij@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
AngeloGioacchino Del Regno [Tue, 11 Oct 2022 13:55:48 +0000 (15:55 +0200)]
clk: mediatek: clk-mux: Add .determine_rate() callback
Since commit
262ca38f4b6e ("clk: Stop forwarding clk_rate_requests
to the parent"), the clk_rate_request is .. as the title says, not
forwarded anymore to the parent: this produces an issue with the
MediaTek clock MUX driver during GPU DVFS on MT8195, but not on
MT8192 or others.
This is because, differently from others, like MT8192 where all of
the clocks in the MFG parents tree are of mtk_mux type, but in the
parent tree of MT8195's MFG clock, we have one mtk_mux clock and
one (clk framework generic) mux clock, like so:
names: mfg_bg3d -> mfg_ck_fast_ref -> top_mfg_core_tmp (or) mfgpll
types: mtk_gate -> mux -> mtk_mux (or) mtk_pll
To solve this issue and also keep the GPU DVFS clocks code working
as expected, wire up a .determine_rate() callback for the mtk_mux
ops; for that, the standard clk_mux_determine_rate_flags() was used
as it was possible to.
This commit was successfully tested on MT6795 Xperia M5, MT8173 Elm,
MT8192 Spherion and MT8195 Tomato; no regressions were seen.
For the sake of some more documentation about this issue here's the
trace of it:
[ 12.211587] ------------[ cut here ]------------
[ 12.211589] WARNING: CPU: 6 PID: 78 at drivers/clk/clk.c:1462 clk_core_init_rate_req+0x84/0x90
[ 12.211593] Modules linked in: stp crct10dif_ce mtk_adsp_common llc rfkill snd_sof_xtensa_dsp
panfrost(+) sbs_battery cros_ec_lid_angle cros_ec_sensors snd_sof_of
cros_ec_sensors_core hid_multitouch cros_usbpd_logger snd_sof gpu_sched
snd_sof_utils fuse ipv6
[ 12.211614] CPU: 6 PID: 78 Comm: kworker/u16:2 Tainted: G W 6.0.0-next-
20221011+ #58
[ 12.211616] Hardware name: Acer Tomato (rev2) board (DT)
[ 12.211617] Workqueue: devfreq_wq devfreq_monitor
[ 12.211620] pstate:
40400009 (nZcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 12.211622] pc : clk_core_init_rate_req+0x84/0x90
[ 12.211625] lr : clk_core_forward_rate_req+0xa4/0xe4
[ 12.211627] sp :
ffff80000893b8e0
[ 12.211628] x29:
ffff80000893b8e0 x28:
ffffdddf92f9b000 x27:
ffff46a2c0e8bc05
[ 12.211632] x26:
ffff46a2c1041200 x25:
0000000000000000 x24:
00000000173eed80
[ 12.211636] x23:
ffff80000893b9c0 x22:
ffff80000893b940 x21:
0000000000000000
[ 12.211641] x20:
ffff46a2c1039f00 x19:
ffff46a2c1039f00 x18:
0000000000000000
[ 12.211645] x17:
0000000000000038 x16:
000000000000d904 x15:
0000000000000003
[ 12.211649] x14:
ffffdddf9357ce48 x13:
ffffdddf935e71c8 x12:
000000000004803c
[ 12.211653] x11:
00000000a867d7ad x10:
00000000a867d7ad x9 :
ffffdddf90c28df4
[ 12.211657] x8 :
ffffdddf9357a980 x7 :
0000000000000000 x6 :
0000000000000004
[ 12.211661] x5 :
ffffffffffffffc8 x4 :
00000000173eed80 x3 :
ffff80000893b940
[ 12.211665] x2 :
00000000173eed80 x1 :
ffff80000893b940 x0 :
0000000000000000
[ 12.211669] Call trace:
[ 12.211670] clk_core_init_rate_req+0x84/0x90
[ 12.211673] clk_core_round_rate_nolock+0xe8/0x10c
[ 12.211675] clk_mux_determine_rate_flags+0x174/0x1f0
[ 12.211677] clk_mux_determine_rate+0x1c/0x30
[ 12.211680] clk_core_determine_round_nolock+0x74/0x130
[ 12.211682] clk_core_round_rate_nolock+0x58/0x10c
[ 12.211684] clk_core_round_rate_nolock+0xf4/0x10c
[ 12.211686] clk_core_set_rate_nolock+0x194/0x2ac
[ 12.211688] clk_set_rate+0x40/0x94
[ 12.211691] _opp_config_clk_single+0x38/0xa0
[ 12.211693] _set_opp+0x1b0/0x500
[ 12.211695] dev_pm_opp_set_rate+0x120/0x290
[ 12.211697] panfrost_devfreq_target+0x3c/0x50 [panfrost]
[ 12.211705] devfreq_set_target+0x8c/0x2d0
[ 12.211707] devfreq_update_target+0xcc/0xf4
[ 12.211708] devfreq_monitor+0x40/0x1d0
[ 12.211710] process_one_work+0x294/0x664
[ 12.211712] worker_thread+0x7c/0x45c
[ 12.211713] kthread+0x104/0x110
[ 12.211716] ret_from_fork+0x10/0x20
[ 12.211718] irq event stamp: 7102
[ 12.211719] hardirqs last enabled at (7101): [<
ffffdddf904ea5a0>] finish_task_switch.isra.0+0xec/0x2f0
[ 12.211723] hardirqs last disabled at (7102): [<
ffffdddf91794b74>] el1_dbg+0x24/0x90
[ 12.211726] softirqs last enabled at (6716): [<
ffffdddf90410be4>] __do_softirq+0x414/0x588
[ 12.211728] softirqs last disabled at (6507): [<
ffffdddf904171d8>] ____do_softirq+0x18/0x24
[ 12.211730] ---[ end trace
0000000000000000 ]---
Fixes:
262ca38f4b6e ("clk: Stop forwarding clk_rate_requests to the parent")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221011135548.318323-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Nick Desaulniers [Fri, 14 Oct 2022 16:53:02 +0000 (09:53 -0700)]
kbuild: add -fno-discard-value-names to cmd_cc_ll_c
When debugging LLVM IR, it can be handy for clang to not discard value
names used for local variables and parameters. Compare the generated IR.
-fdiscard-value-names:
define i32 @core_sys_select(i32 %0, ptr %1, ptr %2, ptr %3, ptr %4) {
%6 = alloca i64
%7 = alloca %struct.poll_wqueues
%8 = alloca [64 x i32]
-fno-discard-value-names:
define i32 @core_sys_select(i32 %n, ptr %inp, ptr %outp, ptr %exp,
ptr %end_time) {
%expire.i = alloca i64
%table.i = alloca %struct.poll_wqueues
%stack_fds = alloca [64 x i32]
The rule for generating human readable LLVM IR (.ll) is only useful as a
debugging feature:
$ make LLVM=1 fs/select.ll
As Fangrui notes:
A LLVM_ENABLE_ASSERTIONS=off build of Clang defaults to
-fdiscard-value-names.
A LLVM_ENABLE_ASSERTIONS=on build of Clang defaults to
-fno-discard-value-names.
Explicitly enable -fno-discard-value-names so that the IR always contains
value names regardless of whether assertions were enabled or not.
Assertions generally are not enabled in releases of clang packaged by
distributions.
Link: https://github.com/ClangBuiltLinux/linux/issues/1467
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Fangrui Song <maskray@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Linus Torvalds [Fri, 14 Oct 2022 20:22:14 +0000 (13:22 -0700)]
Merge tag 'sound-fix-6.1-rc1' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a few remaining patches for 6.1-rc1.
The major changes are the hibernation fixes for HD-audio CS35L41 codec
and the USB-audio small fixes against the last change. In addition, a
couple of HD-audio regression fixes and a couple of potential
mutex-deadlock fixes with OSS emulation in ALSA core side are seen"
* tag 'sound-fix-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda: cs35l41: Support System Suspend
ALSA: hda: cs35l41: Remove suspend/resume hda hooks
ALSA: hda/cs_dsp_ctl: Fix mutex inversion when creating controls
ALSA: hda: hda_cs_dsp_ctl: Ensure pwr_lock is held before reading/writing controls
ALSA: hda: hda_cs_dsp_ctl: Minor clean and redundant code removal
ALSA: oss: Fix potential deadlock at unregistration
ALSA: rawmidi: Drop register_mutex in snd_rawmidi_free()
ALSA: hda/realtek: Add Intel Reference SSID to support headset keys
ALSA: hda/realtek: Add quirk for ASUS GV601R laptop
ALSA: hda/realtek: Correct pin configs for ASUS G533Z
ALSA: usb-audio: Avoid superfluous endpoint setup
ALSA: usb-audio: Correct the return code from snd_usb_endpoint_set_params()
ALSA: usb-audio: Apply mutex around snd_usb_endpoint_set_params()
ALSA: usb-audio: Avoid unnecessary interface change at EP close
ALSA: hda: Update register polling macros
ALSA: hda/realtek: remove ALC289_FIXUP_DUAL_SPK for Dell 5530
Linus Torvalds [Fri, 14 Oct 2022 20:14:03 +0000 (13:14 -0700)]
Merge tag 'leds-6.1-rc1' of git://git./linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"This is very quiet release for LEDs, pca963 got blinking support and
that's pretty much it"
* tag 'leds-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: pca963: fix misleading indentation
dt-bindings: leds: Document mmc trigger
leds: pca963x: fix blink with hw acceleration
Linus Torvalds [Fri, 14 Oct 2022 20:03:00 +0000 (13:03 -0700)]
Merge tag 'sched-psi-2022-10-14' of git://git./linux/kernel/git/tip/tip
Pull PSI updates from Ingo Molnar:
- Various performance optimizations, resulting in a 4%-9% speedup in
the mmtests/config-scheduler-perfpipe micro-benchmark.
- New interface to turn PSI on/off on a per cgroup level.
* tag 'sched-psi-2022-10-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/psi: Per-cgroup PSI accounting disable/re-enable interface
sched/psi: Cache parent psi_group to speed up group iteration
sched/psi: Consolidate cgroup_psi()
sched/psi: Add PSI_IRQ to track IRQ/SOFTIRQ pressure
sched/psi: Remove NR_ONCPU task accounting
sched/psi: Optimize task switch inside shared cgroups again
sched/psi: Move private helpers to sched/stats.h
sched/psi: Save percpu memory when !psi_cgroups_enabled
sched/psi: Don't create cgroup PSI files when psi_disabled
sched/psi: Fix periodic aggregation shut off
Linus Torvalds [Fri, 14 Oct 2022 19:38:03 +0000 (12:38 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Cortex-A55 errata workaround (repeat TLBI)
- AMPERE1 added to the Spectre-BHB affected list
- MTE fix to avoid setting PG_mte_tagged if no tags have been touched
on a page
- Fixed typo in the SCTLR_EL1.SPINTMASK bit naming (the commit log has
other typos)
- perf: return value check in ali_drw_pmu_probe(),
ALIBABA_UNCORE_DRW_PMU dependency on ACPI
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Add AMPERE1 to the Spectre-BHB affected list
arm64: mte: Avoid setting PG_mte_tagged if no tags cleared or restored
MAINTAINERS: rectify file entry in ALIBABA PMU DRIVER
drivers/perf: ALIBABA_UNCORE_DRW_PMU should depend on ACPI
drivers/perf: fix return value check in ali_drw_pmu_probe()
arm64: errata: Add Cortex-A55 to the repeat tlbi list
arm64/sysreg: Fix typo in SCTR_EL1.SPINTMASK
Linus Torvalds [Fri, 14 Oct 2022 19:28:43 +0000 (12:28 -0700)]
Merge tag 'mm-stable-2022-10-13' of git://git./linux/kernel/git/akpm/mm
Pull more MM updates from Andrew Morton:
- fix a race which causes page refcounting errors in ZONE_DEVICE pages
(Alistair Popple)
- fix userfaultfd test harness instability (Peter Xu)
- various other patches in MM, mainly fixes
* tag 'mm-stable-2022-10-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (29 commits)
highmem: fix kmap_to_page() for kmap_local_page() addresses
mm/page_alloc: fix incorrect PGFREE and PGALLOC for high-order page
mm/selftest: uffd: explain the write missing fault check
mm/hugetlb: use hugetlb_pte_stable in migration race check
mm/hugetlb: fix race condition of uffd missing/minor handling
zram: always expose rw_page
LoongArch: update local TLB if PTE entry exists
mm: use update_mmu_tlb() on the second thread
kasan: fix array-bounds warnings in tests
hmm-tests: add test for migrate_device_range()
nouveau/dmem: evict device private memory during release
nouveau/dmem: refactor nouveau_dmem_fault_copy_one()
mm/migrate_device.c: add migrate_device_range()
mm/migrate_device.c: refactor migrate_vma and migrate_deivce_coherent_page()
mm/memremap.c: take a pgmap reference on page allocation
mm: free device private pages have zero refcount
mm/memory.c: fix race when faulting a device private page
mm/damon: use damon_sz_region() in appropriate place
mm/damon: move sz_damon_region to damon_sz_region
lib/test_meminit: add checks for the allocation functions
...
Bjorn Helgaas [Fri, 14 Oct 2022 18:45:45 +0000 (13:45 -0500)]
Revert "PCI: Distribute available resources for root buses, too"
This reverts commit
e96e27fc6f7971380283768e9a734af16b1716ee.
Jonathan reported that this commit broke this topology, where all the space
available on bus 02 was assigned to the 02:00.0 bridge window, leaving none
for the e1000 device at 02:00.1:
pci 0000:00:04.0: bridge window [mem 0x10200000-0x103fffff] to [bus 02-04]
pci 0000:02:00.0: bridge window [mem 0x10200000-0x103fffff] to [bus 03-04]
pci 0000:02:00.1: BAR 0: failed to assign [mem size 0x00020000]
e1000 0000:02:00.1: can't ioremap BAR 0: [??? 0x00000000 flags 0x0]
Link: https://lore.kernel.org/r/20221014124553.0000696f@huawei.com
Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Linus Torvalds [Fri, 14 Oct 2022 19:10:01 +0000 (12:10 -0700)]
Merge tag 'parisc-for-6.1-1' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"Fixes:
- When we added basic vDSO support in kernel 5.18 we introduced a bug
which prevented a mmap() of graphic card memory. This is because we
used the DMB (data memory break trap bit) page flag as special-bit,
but missed to clear that bit when loading the TLB.
- Graphics card memory size was not correctly aligned
- Spelling fixes (from Colin Ian King)
Enhancements:
- PDC console (which uses firmware calls) now rewritten as early
console
- Reduced size of alternative tables"
* tag 'parisc-for-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix spelling mistake "mis-match" -> "mismatch" in eisa driver
parisc: Fix userspace graphics card breakage due to pgtable special bit
parisc: fbdev/stifb: Align graphics memory size to 4MB
parisc: Convert PDC console to an early console
parisc: Reduce kernel size by packing alternative tables