OSDN Git Service
Peter Ujfalusi [Thu, 28 Jan 2010 13:57:04 +0000 (15:57 +0200)]
ASoC: TWL4030: Modify codec default settings
Change the legacy default register configuration, which left some
internal components on.
Now we have either DAPM, or other ways to control these bits,
so there is no need to enable them by default.
The affected parts:
Disable ADCL and ADCR
Disable ARXL2 and ARXR2 analog PGA (playback)
Disable APLL by default
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Kuninori Morimoto [Thu, 28 Jan 2010 04:46:16 +0000 (13:46 +0900)]
ASoC: fsi: Add spin lock operation for accessing shared area
fsi_master_xxx function should be protected by spin lock,
because it are used from both FSI-A and FSI-B.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Guennadi Liakhovetski [Wed, 27 Jan 2010 17:56:23 +0000 (18:56 +0100)]
ASoC: add a WM8978 codec driver
The WM8978 codec from Wolfson Microelectronics is very similar to
wm8974, but is stereo and also has some differences in pin configuration
and internal signal routing. This driver is based on wm8974 and takes
the differences into account.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 27 Jan 2010 20:54:13 +0000 (20:54 +0000)]
ASoC: Note jumper settings for smdk_wm9713 driver on SMDK6410
The board supports both GPIO sets for the AC97 bus and the analogue
outputs can be switched between this and the WM8580 so add some
comments saying what the setup the standard kernel expects is.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Wed, 27 Jan 2010 06:04:36 +0000 (15:04 +0900)]
ASoC: AC97: S3C2443: Remove unused driver
Since, we have generic AC97 controller driver and all the machines
have moved to that, there is no need for old s3c2443-ac97.c to exist.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Wed, 27 Jan 2010 06:02:04 +0000 (15:02 +0900)]
ASoC: AC97: LN2440SBC: Switch to s3c-ac97.c
Switch to use s3c-ac97.c AC97 controller driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Wed, 27 Jan 2010 06:01:03 +0000 (15:01 +0900)]
ASoC: AC97: SMDK2443: Switch to s3c-ac97.c
Switch to use s3c-ac97.c AC97 controller driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Wed, 27 Jan 2010 05:59:19 +0000 (14:59 +0900)]
ASoC: AC97: SMDK: Add wm9713 machine driver
This patch adds the common machine driver for SMDKs that
have a WM9713 codec attched to the AC97 controller.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Wed, 27 Jan 2010 05:59:08 +0000 (14:59 +0900)]
ASoC: AC97: S3C: Add controller driver
Add the AC97 controller driver for Samsung SoCs that have one.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Barry Song [Wed, 27 Jan 2010 03:46:18 +0000 (11:46 +0800)]
ASoC: ad1938: use soc-cache framework for codec registers access
Signed-off-by: Barry Song <Barry.Song@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Barry Song [Wed, 27 Jan 2010 03:46:17 +0000 (11:46 +0800)]
ASoC: ad1836: use soc-cache framework for codec registers access
Signed-off-by: Barry Song <Barry.Song@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Chaithrika U S [Wed, 20 Jan 2010 11:36:33 +0000 (17:06 +0530)]
ASoC: DaVinci: Fix stream restart error
Sometimes after a suspend-resume cycle, the ALSA application
restarts the stream when resume fails and McASP fails to work
as the clock is not enabled. This patch corrects this bug.
Testes on TI DA850/OMAP-L138 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Mon, 25 Jan 2010 14:52:48 +0000 (14:52 +0000)]
Merge branch 'for-2.6.33' into for-2.6.34
Barry Song [Mon, 25 Jan 2010 08:42:25 +0000 (16:42 +0800)]
ASoC: ad1836: reset and restore clock control mode in suspend/resume entry
tests show frequent suspend/resume(frequent poweroff/on ad1836 internal
components) maybe make ad1836 clock mode wrong sometimes after wakeup.
This patch reset/restore ad1836 clock mode while executing PM, then
ad1836 can always resume to right clock status.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Guennadi Liakhovetski [Fri, 22 Jan 2010 18:09:03 +0000 (19:09 +0100)]
ASoC: add DAI and platform / DMA drivers for SH SIU
Several SuperH platforms, including sh7722, sh7343, sh7354, sh7367 include
a Sound Interface Unit (SIU). This patch adds DAI and platform / DMA
drivers for this interface.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Guennadi Liakhovetski [Thu, 21 Jan 2010 21:04:03 +0000 (22:04 +0100)]
ASoC: add helper macros to declare struct soc_enum instances
Several shortcuts for popular uses of some of SOC_ENUM_* and
SOC_VALUE_ENUM_* macros.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Guennadi Liakhovetski [Thu, 21 Jan 2010 20:10:47 +0000 (21:10 +0100)]
ASoC: add simplified versions of widget macros
Many macros from include/sound/soc-dapm.h take an array and a number of
elements in it as arguments, whereas most users use static arrays and use
"x, ARRAY_SIZE(x)" as arguments. This patch adds simplified versions of
those macros, calling ARRAY_SIZE() internally.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.oc.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Guennadi Liakhovetski [Fri, 22 Jan 2010 17:00:03 +0000 (18:00 +0100)]
ASoC: fix a memory-leak in wm8903
Remember to free the temporary register-cache.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Linus Torvalds [Thu, 21 Jan 2010 23:31:35 +0000 (15:31 -0800)]
Linux 2.6.33-rc5
Linus Torvalds [Thu, 21 Jan 2010 16:50:04 +0000 (08:50 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: x86: Add support for the ANY bit
perf: Change the is_software_event() definition
perf: Honour event state for aux stream data
perf: Fix perf_event_do_pending() fallback callsite
perf kmem: Print usage help for unknown commands
perf kmem: Increase "Hit" column length
hw-breakpoints, perf: Fix broken mmiotrace due to dr6 by reference change
perf timechart: Use tid not pid for COMM change
Linus Torvalds [Thu, 21 Jan 2010 16:49:52 +0000 (08:49 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Reassign prev and switch_count when reacquire_kernel_lock() fail
sched: Fix vmark regression on big machines
Linus Torvalds [Thu, 21 Jan 2010 15:42:59 +0000 (07:42 -0800)]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: retry FS IOs even if it has failed with AC_ERR_INVALID
Linus Torvalds [Thu, 21 Jan 2010 15:37:20 +0000 (07:37 -0800)]
Merge git://git./linux/kernel/git/gregkh/tty-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: fix race in tty_fasync
serial: serial_cs: oxsemi quirk breaks resume
serial: imx: bit &/| confusion
serial: Fix crash if the minimum rate of the device is > 9600 baud
serial-core: resume serial hardware with no_console_suspend
serial: 8250_pnp: use wildcard for serial Wacom tablets
nozomi: quick fix for the close/close bug
compat_ioctl: Supress "unknown cmd" message on serial /dev/console
Linus Torvalds [Thu, 21 Jan 2010 15:36:55 +0000 (07:36 -0800)]
Merge git://git./linux/kernel/git/gregkh/staging-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: hv: fix smp problems in the hyperv core code
Staging: et131x: Fix 2.6.33rc1 regression in et131x
Staging: asus_oled: fix oops in 2.6.32.2
Linus Torvalds [Thu, 21 Jan 2010 15:36:31 +0000 (07:36 -0800)]
Merge git://git./linux/kernel/git/gregkh/driver-core-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Revert "sysdev: fix prototype for memory_sysdev_class show/store functions"
driver-core: fix devtmpfs crash on s390
Linus Torvalds [Thu, 21 Jan 2010 15:35:43 +0000 (07:35 -0800)]
Merge git://git./linux/kernel/git/gregkh/usb-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: isp1362: fix build failure on ARM systems via irq_flags cleanup
USB: isp1362: better 64bit printf warning fixes
USB: fix usbstorage for 2770:915d delivers no FAT
USB: Fix level of isp1760 Reloading ptd error message
USB: FHCI: avoid NULL pointer dereference
USB: Fix duplicate sysfs problem after device reset.
USB: add speed values for USB 3.0 and wireless controllers
USB: add missing delay during remote wakeup
USB: EHCI & UHCI: fix race between root-hub suspend and port resume
USB: EHCI: fix handling of unusual interrupt intervals
USB: Don't use GFP_KERNEL while we cannot reset a storage device
USB: fix bitmask merge error
usb: serial: fix memory leak in generic driver
USB: serial: fix USB serial fix kfifo_len locking
Linus Torvalds [Thu, 21 Jan 2010 15:32:11 +0000 (07:32 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
fs/bio.c: fix shadows sparse warning
drbd: The kernel code is now equivalent to out of tree release 8.3.7
drbd: Allow online resizing of DRBD devices while peer not reachable (needs to be explicitly forced)
drbd: Don't go into StandAlone mode when authentification failes because of network error
drivers/block/drbd/drbd_receiver.c: correct NULL test
cfq-iosched: Respect ioprio_class when preempting
genhd: overlapping variable definition
block: removed unused as_io_context
DM: Fix device mapper topology stacking
block: bdev_stack_limits wrapper
block: Fix discard alignment calculation and printing
block: Correct handling of bottom device misaligment
drbd: check on CONFIG_LBDAF, not LBD
drivers/block/drbd: Correct NULL test
drbd: Silenced an assert that could triggered after changing write ordering method
drbd: Kconfig fix
drbd: Fix for a race between IO and a detach operation [Bugz 262]
drbd: Use drbd_crypto_is_hash() instead of an open coded check
Linus Torvalds [Thu, 21 Jan 2010 15:29:36 +0000 (07:29 -0800)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits)
ACPI: delete acpi_processor_power_verify_c2()
ACPI: allow C3 > 1000usec
ACPI: enable C2 and Turbo-mode on Nehalem notebooks on A/C
ACPI: power_meter: remove double kfree()
ACPI: processor: restrict early _PDC to opt-in platforms
ACPI: Fix unused variable warning in sbs.c
acpi: make ACPI device id constant
sony-laptop - fix using of uninitialized variable
ACPI: Fix section mismatch error for acpi_early_processor_set_pdc()
eeepc-laptop: disable wireless hotplug for 1201N
eeepc-laptop: add hotplug_disable parameter
eeepc-laptop: switch to using sparse keymap library
eeepc-laptop: dmi blacklist to disable pci hotplug code
eeepc-laptop: disable cpu speed control on EeePC 701
ACPI: don't cond_resched if irq is disabled
ACPI: Remove unnecessary cast.
ACPI: Advertise to BIOS in _OSC: _OST on _PPC changes
ACPI: EC: Add wait for irq storm
ACPI: SBS: Move SBS HC callback to faster Notify queue
x86, ACPI: delete acpi_boot_table_init() return value
...
Linus Torvalds [Thu, 21 Jan 2010 15:28:54 +0000 (07:28 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ecryptfs/ecryptfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
ecryptfs: use after free
ecryptfs: Eliminate useless code
ecryptfs: fix interpose/interpolate typos in comments
ecryptfs: pass matching flags to interpose as defined and used there
ecryptfs: remove unnecessary d_drop calls in ecryptfs_link
ecryptfs: don't ignore return value from lock_rename
ecryptfs: initialize private persistent file before dereferencing pointer
eCryptfs: Remove mmap from directory operations
eCryptfs: Add getattr function
eCryptfs: Use notify_change for truncating lower inodes
Linus Torvalds [Thu, 21 Jan 2010 15:28:05 +0000 (07:28 -0800)]
Merge git://git./linux/kernel/git/mason/btrfs-unstable
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix possible panic on unmount
Btrfs: deal with NULL acl sent to btrfs_set_acl
Btrfs: fix regression in orphan cleanup
Btrfs: Fix race in btrfs_mark_extent_written
Btrfs, fix memory leaks in error paths
Btrfs: align offsets for btrfs_ordered_update_i_size
btrfs: fix missing last-entry in readdir(3)
Yongseok Koh [Tue, 19 Jan 2010 08:33:49 +0000 (17:33 +0900)]
vmalloc: remove BUG_ON due to racy counting of VM_LAZY_FREE
In free_unmap_area_noflush(), va->flags is marked as VM_LAZY_FREE first, and
then vmap_lazy_nr is increased atomically.
But, in __purge_vmap_area_lazy(), while traversing of vmap_are_list, nr
is counted by checking VM_LAZY_FREE is set to va->flags. After counting
the variable nr, kernel reads vmap_lazy_nr atomically and checks a
BUG_ON condition whether nr is greater than vmap_lazy_nr to prevent
vmap_lazy_nr from being negative.
The problem is that, if interrupted right after marking VM_LAZY_FREE,
increment of vmap_lazy_nr can be delayed. Consequently, BUG_ON
condition can be met because nr is counted more than vmap_lazy_nr.
It is highly probable when vmalloc/vfree are called frequently. This
scenario have been verified by adding delay between marking VM_LAZY_FREE
and increasing vmap_lazy_nr in free_unmap_area_noflush().
Even the vmap_lazy_nr is for checking high watermark, it never be the
strict watermark. Although the BUG_ON condition is to prevent
vmap_lazy_nr from being negative, vmap_lazy_nr is signed variable. So,
it could go down to negative value temporarily.
Consequently, removing the BUG_ON condition is proper.
A possible BUG_ON message is like the below.
kernel BUG at mm/vmalloc.c:517!
invalid opcode: 0000 [#1] SMP
EIP: 0060:[<
c04824a4>] EFLAGS:
00010297 CPU: 3
EIP is at __purge_vmap_area_lazy+0x144/0x150
EAX:
ee8a8818 EBX:
c08e77d4 ECX:
e7c7ae40 EDX:
c08e77ec
ESI:
000081fe EDI:
e7c7ae60 EBP:
e7c7ae64 ESP:
e7c7ae3c
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Call Trace:
[<
c0482ad9>] free_unmap_vmap_area_noflush+0x69/0x70
[<
c0482b02>] remove_vm_area+0x22/0x70
[<
c0482c15>] __vunmap+0x45/0xe0
[<
c04831ec>] vmalloc+0x2c/0x30
Code: 8d 59 e0 eb 04 66 90 89 cb 89 d0 e8 87 fe ff ff 8b 43 20 89 da 8d 48 e0 8d 43 20 3b 04 24 75 e7 fe 05 a8 a5 a3 c0 e9 78 ff ff ff <0f> 0b eb fe 90 8d b4 26 00 00 00 00 56 89 c6 b8 ac a5 a3 c0 31
EIP: [<
c04824a4>] __purge_vmap_area_lazy+0x144/0x150 SS:ESP 0068:
e7c7ae3c
[ See also http://marc.info/?l=linux-kernel&m=
126335856228090&w=2 ]
Signed-off-by: Yongseok Koh <yongseok.koh@samsung.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 21 Jan 2010 15:16:27 +0000 (07:16 -0800)]
Merge branch 'sh/for-2.6.33' of git://git./linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh64: wire up sys_accept4.
sh: unwire sys_recvmmsg.
sh: ms7724: Correct sh-eth EEPROM polling timeout.
Linus Torvalds [Thu, 21 Jan 2010 15:15:10 +0000 (07:15 -0800)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 5888/1: arm: Update comments in cacheflush.h and remove unnecessary V6 and V7 comments
ARM: 5886/1: arm: Fix cpu_proc_fin() for proc-v7.S and make kexec work
ARM: 5885/1: arm: Flush TLB entries in setup_mm_for_reboot()
ARM: 5884/1: arm: Fix DCC console for v7
ARM: 5883/1: Revert "disable NX support for OABI-supporting kernels"
ARM: 5882/1: ARM: Fix uncompress code compile for different defines of flush(void)
ARM: fix badly placed mach/plat entries in Kconfig & Makefile
Stephane Eranian [Mon, 18 Jan 2010 08:58:01 +0000 (10:58 +0200)]
perf: x86: Add support for the ANY bit
Propagate the ANY bit into the fixed counter config for v3 and higher.
Signed-off-by: Stephane Eranian <eranian@google.com>
[a.p.zijlstra@chello.nl: split from larger patch]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
4b5430c6.
0f975e0a.1bf9.
ffff85fe@mx.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter Zijlstra [Mon, 18 Jan 2010 13:02:16 +0000 (14:02 +0100)]
perf: Change the is_software_event() definition
The is_software_event() definition always confuses me because its an
exclusive expression, make it an inclusive one.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter Zijlstra [Mon, 18 Jan 2010 08:12:32 +0000 (09:12 +0100)]
perf: Honour event state for aux stream data
Anton reported that perf record kept receiving events even after calling
ioctl(PERF_EVENT_IOC_DISABLE). It turns out that FORK,COMM and MMAP
events didn't respect the disabled state and kept flowing in.
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Anton Blanchard <anton@samba.org>
LKML-Reference: <
1263459187.4244.265.camel@laptop>
CC: stable@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter Zijlstra [Mon, 18 Jan 2010 08:08:26 +0000 (09:08 +0100)]
perf: Fix perf_event_do_pending() fallback callsite
Paul questioned the context in which we should call
perf_event_do_pending(). After looking at that I found that it should be
called from IRQ context these days, however the fallback call-site is
placed in softirq context. Ammend this by placing the callback in the IRQ
timer path.
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
1263374859.4244.192.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yong Zhang [Mon, 11 Jan 2010 06:21:25 +0000 (14:21 +0800)]
sched: Reassign prev and switch_count when reacquire_kernel_lock() fail
Assume A->B schedule is processing, if B have acquired BKL before and it
need reschedule this time. Then on B's context, it will go to
need_resched_nonpreemptible for reschedule. But at this time, prev and
switch_count are related to A. It's wrong and will lead to incorrect
scheduler statistics.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <2674af741001102238w7b0ddcadref00d345e2181d11@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Mike Galbraith [Mon, 4 Jan 2010 13:44:56 +0000 (14:44 +0100)]
sched: Fix vmark regression on big machines
SD_PREFER_SIBLING is set at the CPU domain level if power saving isn't
enabled, leading to many cache misses on large machines as we traverse
looking for an idle shared cache to wake to. Change the enabler of
select_idle_sibling() to SD_SHARE_PKG_RESOURCES, and enable same at the
sibling domain level.
Reported-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
1262612696.15495.15.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Mark Brown [Thu, 21 Jan 2010 11:33:20 +0000 (11:33 +0000)]
ASoC: Use BIAS_OFF when idle for wm_hubs devices
This provides a small power saving when audio is inactive.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Tue, 19 Jan 2010 22:49:43 +0000 (22:49 +0000)]
ASoC: Support turning off bias when the CODEC is idle
Currently ASoC always maintains the bias of the CODEC while the system
is active. With older mobile CODECs this is required since the outputs
are referenced to a non-zero voltage and enabling or disabling this
voltage without audible pops or clicks in the output takes too long to
do when starting or stopping audio.
As a result of features such as ground referenced outputs and class D
speaker drivers current generation devices are able to power on and off
much more quickly without these system level issues so provide a new
flag idle_bias_off in snd_soc_codec which will cause the core to turn
off the CODEC bias. The distinction between STANDBY and OFF is still
maintained. This is partly for consistency but also allows for
potential future extensions such as per-machine overrides or deferring
the bias removal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Wed, 20 Jan 2010 18:18:35 +0000 (18:18 +0000)]
ASoC: Remove console DAPM debug code
The same information is now visible via debugfs and with large modern
devices dumping everything to the console can be very resource
intensive, causing more harm than good.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Lothar Wassmann [Fri, 15 Jan 2010 19:42:02 +0000 (14:42 -0500)]
USB: isp1362: fix build failure on ARM systems via irq_flags cleanup
There was some left over #ifdef ARM logic that is outdated but no one
really noticed. So instead of relying on this tricky logic, properly
load and utilize the platform irq_flags resources.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lothar Wassmann [Fri, 15 Jan 2010 13:04:55 +0000 (08:04 -0500)]
USB: isp1362: better 64bit printf warning fixes
Some hosts that treat the return value of sizeof differently from unsigned
long might still hit warnings. So use %zu for sizeof() values. This is a
better version of the previous commit
b0a9cf297e58721933.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ryan May [Wed, 6 Jan 2010 16:09:25 +0000 (10:09 -0600)]
USB: fix usbstorage for 2770:915d delivers no FAT
Resolves kernel.org bug 14914.
Remove entry for 2770:915d (usb digital camera with mass storage
support) from unusual_devs.h. The fix triggered by the entry causes
the file system on the camera to be completely inaccessible (no
partition table, the device is not mountable).
The patch works, but let me clarify a few things about it. All the
patch does is remove the entry for this device from the
drivers/usb/storage/unusual_devs.h, which is supposed to help with a
problem with the device's reported size (I think). I'm pretty sure it
was originally added for a reason, so I'm not sure removing it won't
cause other problems to reappear. Also, I should note that this
unusual_devs.h entry was present (and activating workarounds) in
2.6.29, but in that version everything works fine. Starting with
2.6.30, things no longer work.
Signed-off-by: Ryan May <rmay31@gmail.com>
Cc: Rohan Hart <rohan.hart17@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Colin Tuckley [Thu, 7 Jan 2010 11:22:47 +0000 (11:22 +0000)]
USB: Fix level of isp1760 Reloading ptd error message
This error message is not actually an error, it's an information
message. It is triggered when a transfer which ended in a NAQ is
retried successfully by the hardware.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexander Beregalov [Thu, 7 Jan 2010 01:17:32 +0000 (04:17 +0300)]
USB: FHCI: avoid NULL pointer dereference
Assign fhci only if usb is not NULL.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Wed, 6 Jan 2010 18:16:51 +0000 (10:16 -0800)]
USB: Fix duplicate sysfs problem after device reset.
Borislav Petkov reports issues with duplicate sysfs endpoint files after a
resume from a hibernate. It turns out that the code to support alternate
settings under xHCI has issues when a device with a non-default alternate
setting is reset during the hibernate:
[ 427.681810] Restarting tasks ...
[ 427.681995] hub 1-0:1.0: state 7 ports 6 chg 0004 evt 0000
[ 427.682019] usb usb3: usb resume
[ 427.682030] ohci_hcd 0000:00:12.0: wakeup root hub
[ 427.682191] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[ 427.682205] usb 1-2: usb wakeup-resume
[ 427.682226] usb 1-2: finish reset-resume
[ 427.682886] done.
[ 427.734658] ehci_hcd 0000:00:12.2: port 2 high speed
[ 427.734663] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 427.746682] hub 3-0:1.0: hub_reset_resume
[ 427.746693] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 427.786715] usb 1-2: reset high speed USB device using ehci_hcd and address 2
[ 427.839653] ehci_hcd 0000:00:12.2: port 2 high speed
[ 427.839666] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 427.847717] ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
[ 427.915497] hub 1-2:1.0: remove_intf_ep_devs: if:
ffff88022f9e8800 ->ep_devs_created: 1
[ 427.915774] hub 1-2:1.0: remove_intf_ep_devs: bNumEndpoints: 1
[ 427.915934] hub 1-2:1.0: if:
ffff88022f9e8800: endpoint devs removed.
[ 427.916158] hub 1-2:1.0: create_intf_ep_devs: if:
ffff88022f9e8800 ->ep_devs_created: 0, ->unregistering: 0
[ 427.916434] hub 1-2:1.0: create_intf_ep_devs: bNumEndpoints: 1
[ 427.916609] ep_81: create, parent hub
[ 427.916632] ------------[ cut here ]------------
[ 427.916644] WARNING: at fs/sysfs/dir.c:477 sysfs_add_one+0x82/0x96()
[ 427.916649] Hardware name: System Product Name
[ 427.916653] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:12.2/usb1/1-2/1-2:1.0/ep_81'
[ 427.916658] Modules linked in: binfmt_misc kvm_amd kvm powernow_k8 cpufreq_ondemand cpufreq_powersave cpufreq_userspace freq_table cpufreq_conservative ipv6 vfat fat
+8250_pnp 8250 pcspkr ohci_hcd serial_core k10temp edac_core
[ 427.916694] Pid: 278, comm: khubd Not tainted
2.6.33-rc2-00187-g08d869a-dirty #13
[ 427.916699] Call Trace:
The problem is caused by a mismatch between the USB core's view of the
device state and the USB device and xHCI host's view of the device state.
After the device reset and re-configuration, the device and the xHCI host
think they are using alternate setting 0 of all interfaces. However, the
USB core keeps track of the old state, which may include non-zero
alternate settings. It uses intf->cur_altsetting to keep the endpoint
sysfs files for the old state across the reset.
The bandwidth allocation functions need to know what the xHCI host thinks
the current alternate settings are, so original patch set
intf->cur_altsetting to the alternate setting 0. This caused duplicate
endpoint files to be created.
The solution is to not set intf->cur_altsetting before calling
usb_set_interface() in usb_reset_and_verify_device(). Instead, we add a
new flag to struct usb_interface to tell usb_hcd_alloc_bandwidth() to use
alternate setting 0 as the currently installed alternate setting.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Thu, 14 Jan 2010 18:33:19 +0000 (10:33 -0800)]
USB: add speed values for USB 3.0 and wireless controllers
These controllers say "unknown" for their speed in sysfs, which
obviously isn't correct.
Reported-by: Kurt Garloff <garloff@novell.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 8 Jan 2010 16:18:38 +0000 (11:18 -0500)]
USB: add missing delay during remote wakeup
This patch (as1330) fixes a bug in khbud's handling of remote
wakeups. When a device sends a remote-wakeup request, the parent hub
(or the host controller driver, for directly attached devices) begins
the resume sequence and notifies khubd when the sequence finishes. At
this point the port's SUSPEND feature is automatically turned off.
However the device needs an additional 10-ms resume-recovery time
(TRSMRCY in the USB spec). Khubd does not wait for this delay if the
SUSPEND feature is off, and as a result some devices fail to behave
properly following a remote wakeup. This patch adds the missing
delay to the remote-wakeup path.
It also extends the resume-signalling delay used by ehci-hcd and
uhci-hcd from 20 ms (the value in the spec) to 25 ms (the value we use
for non-remote-wakeup resumes). The extra time appears to help some
devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Cc: Rickard Bellini <rickard.bellini@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 8 Jan 2010 16:18:20 +0000 (11:18 -0500)]
USB: EHCI & UHCI: fix race between root-hub suspend and port resume
This patch (as1321) fixes a problem with EHCI and UHCI root-hub
suspends: If the suspend occurs while a port is trying to resume, the
resume doesn't finish and simply gets lost. When remote wakeup is
enabled, this is undesirable behavior.
The patch checks first to see if any port resumes are in progress, and
if they are then it fails the root-hub suspend with -EBUSY.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 8 Jan 2010 16:17:55 +0000 (11:17 -0500)]
USB: EHCI: fix handling of unusual interrupt intervals
This patch (as1320) fixes two problems related to interrupt-URB
scheduling in ehci-hcd.
URBs with an interval of 2 or 4 microframes aren't handled.
For the time being, the patch reduces to interval to 1 uframe.
URBs are constrained to have an interval no larger than 1024
frames by usb_submit_urb(). But some EHCI controllers allow
use of a schedule as short as 256 frames; for these
controllers we may have to decrease the interval to the
actual schedule length.
The second problem isn't very significant since few devices expose
interrupt endpoints with an interval larger than 256 frames. But the
first problem is critical; it will prevent the kernel from working
with devices having interrupt intervals of 2 or 4 uframes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Tested-by: Glynn Farrow <farrowg@sg.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Tue, 12 Jan 2010 11:32:50 +0000 (12:32 +0100)]
USB: Don't use GFP_KERNEL while we cannot reset a storage device
Memory allocations with GFP_KERNEL can cause IO to a storage
device which can fail resulting in a need to reset the device.
Therefore GFP_KERNEL cannot be safely used between usb_lock_device()
and usb_unlock_device(). Replace by GFP_NOIO.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 23 Dec 2009 04:16:32 +0000 (23:16 -0500)]
USB: fix bitmask merge error
This patch adds a mask bit which was mistakenly omitted from the
as1311 patch (usb-storage: add BAD_SENSE flag).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johan Hovold [Wed, 6 Jan 2010 23:48:42 +0000 (15:48 -0800)]
usb: serial: fix memory leak in generic driver
Fix a regression introduced by commit
715b1dc01fe44537e8fce9566e4bb48d6821d84b ("USB: usb_debug,
usb_generic_serial: implement multi urb write").
URB transfer buffer was never freed when using multi-urb writes.
Currently the only driver enabling multi-urb writes is usb_debug.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stefani Seibold [Tue, 5 Jan 2010 13:30:31 +0000 (14:30 +0100)]
USB: serial: fix USB serial fix kfifo_len locking
This patch fix a possible race bug in drivers/usb/serial/generic with
the new kfifo API.
Please apply it to the 2.6.33-rc* tree.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 8 Jan 2010 17:06:40 +0000 (09:06 -0800)]
Staging: hv: fix smp problems in the hyperv core code
This fixes a number of SMP problems that were in the hyperv core code.
Patch originally written by K. Y. Srinivasan <ksrinivasan@novell.com>
but forward ported to the latest in-kernel code and tweaked slightly by
me.
Novell, Inc. hereby disclaims all copyright in any derivative work
copyright associated with this patch.
Signed-off-by: K. Y. Srinivasan <ksrinivasan@novell.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Wed, 6 Jan 2010 14:01:26 +0000 (14:01 +0000)]
Staging: et131x: Fix 2.6.33rc1 regression in et131x
et131x: Fix 12bit wrapping
From: Alan Cox <alan@linux.intel.com>
The 12bit wrap logic conversion is wrong and this shows up for some
memory sizes and layouts of card. Patch it up for now, once the kernel
view of status is cleaned up it'll become two variables and a lot saner.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Eugeni Dodonov [Wed, 23 Dec 2009 12:27:22 +0000 (10:27 -0200)]
Staging: asus_oled: fix oops in 2.6.32.2
After updating to 2.6.32 kernel, I started experiencing Oopses caused by
the asus_oled module. After quick investigation, I wrapped this simple
patch which fixes an Oops in by asus_oled module on 2.6.32.2 kernel,
caused by incorrect usage of strict_strtoul function call within
set_enabled and set_disabled functions. This can be triggered by simple
running the userspace client for asus_old (e.g., 'asusoled -e' or
'asusoled -d').
Signed-off-by: Eugeni Dodonov <eugeni@mandriva.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Thu, 17 Dec 2009 15:07:19 +0000 (07:07 -0800)]
tty: fix race in tty_fasync
We need to keep the lock held over the call to __f_setown() to
prevent a PID race.
Thanks to Al Viro for pointing out the problem, and to Travis for
making us look here in the first place.
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Tavis Ormandy <taviso@google.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Julien Tinnes <jln@google.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pavel Machek [Wed, 9 Dec 2009 20:31:31 +0000 (12:31 -0800)]
serial: serial_cs: oxsemi quirk breaks resume
Quirk is applied on all cards with given manfid (is it that correct?).
Unfortunately, that quirk breaks resume on zaurus with billionton
bluetooth card inserted: c950ctrl is 0 and outb() faults.
I believe it is simply not a multiport card. (info->multi == 1). ...
... confirmed by printks.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Roel Kluin [Wed, 9 Dec 2009 20:31:36 +0000 (12:31 -0800)]
serial: imx: bit &/| confusion
Since UCR1_UARTEN is defined 1, the port was always treated as enabled.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Oskar Schirmer <os@emlix.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabian Godehardt <fg@emlix.com>
Cc: Daniel Glöckner <dg@emlix.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Mon, 4 Jan 2010 16:26:21 +0000 (16:26 +0000)]
serial: Fix crash if the minimum rate of the device is > 9600 baud
In that situation if the old rate is invalid and the new rate is invalid
and the chip cannot do 9600 baud we report zero, which makes all the
drivers explode.
Instead force the rate based on min/max
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanislav Brabec [Wed, 2 Dec 2009 15:20:56 +0000 (16:20 +0100)]
serial-core: resume serial hardware with no_console_suspend
Perform a tricky suspend/resume even with no_console_suspend.
With no_console_suspend, kernel skips serial port suspend/resume and the
serial hardware may remain in undefined state after resume. It actually
happens on devices that don't have BIOS that handle serial
initialization. It makes impossible to use serial console after resume.
Devices affected by this problem include:
Sharp Zaurus devices
Several PXA based ARM embedded boards
The patch does:
- Save the hardware state
- Perform buffer flush in time of its suspend call
- Tell the driver that port is suspended
- But still accept new data
- And keep console hardware in state that allows to send them
It allows to capture late console messages without breaking console
after resume.
This is just a resend of a patch discussed in these threads, as the
patch was not yet applied.
"Possible suspend/resume regression in .32-rc?" (Nov 1-5, 2009, ARM
list, later LKML)
"serial-core: resume serial hardware with no_console_suspend" (Sep
15-Oct 18, 2009, LKML & ARM lists)
Signed-off-by: Stanislav Brabec <sbrabec@suse.cz>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Garrett [Wed, 9 Dec 2009 20:31:37 +0000 (12:31 -0800)]
serial: 8250_pnp: use wildcard for serial Wacom tablets
Wacom claims that the WACF namespace will always be devoted to serial
Wacom tablets. Remove the existing entries and add a wildcard to avoid
having to update the kernel every time they add a new device.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Mon, 4 Jan 2010 16:26:50 +0000 (16:26 +0000)]
nozomi: quick fix for the close/close bug
Nozomi goes wrong if you get the sequence
open
open
close
[stuff]
close
which turns out to occur on some ppp type setups.
This is a quick patch up for the problem. It's not really fixing Nozomi
which completely fails to implement tty open/close semantics and all the
other needed stuff. Doing it right is a rather more invasive patch set and
not one that will backport.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Atsushi Nemoto [Sun, 10 Jan 2010 14:29:16 +0000 (23:29 +0900)]
compat_ioctl: Supress "unknown cmd" message on serial /dev/console
After the commit
fb07a5f8 ("compat_ioctl: remove all VT ioctl
handling"), I got this error message on 64-bit mips kernel with 32-bit
busybox userland:
ioctl32(init:1): Unknown cmd fd(0) cmd(
00005600){t:'V';sz:0} arg(
7fd76480) on /dev/console
The cmd 5600 is VT_OPENQRY. The busybox's init issues this ioctl to
know vt-console or serial-console. If the console was serial console,
VT ioctls are not handled by the serial driver.
And by quick search, I found some programs using VT_GETMODE to check
vt-console is available or not.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Tue, 19 Jan 2010 21:08:16 +0000 (13:08 -0800)]
Revert "sysdev: fix prototype for memory_sysdev_class show/store functions"
This reverts commit
8ff410daa009c4b44be445ded5b0cec00abc0426
It should not have been sent to Linus's tree yet, as it depends
on changes that are queued up in my driver-core for the .34 kernel
merge.
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: "Zheng, Shaohui" <shaohui.zheng@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Heiko Carstens [Mon, 18 Jan 2010 13:36:12 +0000 (14:36 +0100)]
driver-core: fix devtmpfs crash on s390
On Mon, Jan 18, 2010 at 05:26:20PM +0530, Sachin Sant wrote:
> Hello Heiko,
>
> Today while trying to boot next-
20100118 i came across
> the following Oops :
>
> Brought up 4 CPUs
> Unable to handle kernel pointer dereference at virtual kernel address
0000000000
> 543000
> Oops: 0004 #1 SMP
> Modules linked in:
> CPU: 0 Not tainted 2.6.33-rc4-autotest-next-
20100118-5-default #1
> Process swapper (pid: 1, task:
00000000fd792038, ksp:
00000000fd797a30)
> Krnl PSW :
0704200180000000 00000000001eb0b8 (shmem_parse_options+0xc0/0x328)
> R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:0 CC:2 PM:0 EA:3
> Krnl GPRS:
000000000054388a 000000000000003d 0000000000543836 000000000000003d
>
0000000000000000 0000000000483f28 0000000000536112 00000000fd797d00
>
00000000fd4ba100 0000000000000100 0000000000483978 0000000000543832
>
0000000000000000 0000000000465958 00000000001eb0b0 00000000fd797c58
> Krnl Code:
00000000001eb0aa:
c0e5000994f1 brasl %r14,31da8c
>
00000000001eb0b0:
b9020022 ltgr %r2,%r2
>
00000000001eb0b4:
a784010b brc 8,1eb2ca
> >
00000000001eb0b8:
92002000 mvi 0(%r2),0
>
00000000001eb0bc:
a7080000 lhi %r0,0
>
00000000001eb0c0:
41902001 la %r9,1(%r2)
>
00000000001eb0c4:
b9040016 lgr %r1,%r6
>
00000000001eb0c8:
b904002b lgr %r2,%r11
> Call Trace:
> (<
00000000fd797c50> 0xfd797c50)
> <
00000000001eb5da> shmem_fill_super+0x13a/0x25c
> <
0000000000228cfa> get_sb_single+0xbe/0xdc
> <
000000000034ffc0> dev_get_sb+0x2c/0x38
> <
000000000066c602> devtmpfs_init+0x46/0xc0
> <
000000000066c53e> driver_init+0x22/0x60
> <
000000000064d40a> kernel_init+0x24e/0x3d0
> <
000000000010a7ea> kernel_thread_starter+0x6/0xc
> <
000000000010a7e4> kernel_thread_starter+0x0/0xc
>
> I never tried to boot a kernel with DEVTMPFS enabled on a s390 box.
> So am wondering if this is supported or not ? If you think this
> is supported i will send a mail to community on this.
There is nothing arch specific to devtmpfs. This part crashes because the
kernel tries to modify the data read-only section which is write protected
on s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tejun Heo [Thu, 14 Jan 2010 07:18:09 +0000 (16:18 +0900)]
libata: retry FS IOs even if it has failed with AC_ERR_INVALID
libata currently doesn't retry if a command fails with AC_ERR_INVALID
assuming that retrying won't get it any further even if retried.
However, a failure may be classified as invalid through hardware
glitch (incorrect reading of the error register or firmware bug) and
there isn't whole lot to gain by not retrying as actually invalid
commands will be failed immediately. Also, commands serving FS IOs
are extremely unlikely to be invalid. Retry FS IOs even if it's
marked invalid.
Transient and incorrect invalid failure was seen while debugging
firmware related issue on Samsung n130 on bko#14314.
http://bugzilla.kernel.org/show_bug.cgi?id=14314
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Peter Ujfalusi [Wed, 20 Jan 2010 07:39:36 +0000 (09:39 +0200)]
ASoC: tlv320dac33: Burst mode BCLK divider configuration
Add possibility to configure the burst mode BCLK divider through platform
data structure.
The BCLK divider changes the actual speed of the serial bus in burst mode,
which is faster than the sampling frequency of the running stream.
In this way platforms can experiment with the optimal burst speed without
the need to modify the codec driver itself.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Peter Ujfalusi [Wed, 20 Jan 2010 07:39:35 +0000 (09:39 +0200)]
ASoC: tlv320dac33: BCLK divider fix
The BCLK divider was not configured in case of mode7.
This leads to unpredictable behavior when switching between FIFO modes.
Configure the BCLK divider depending on the fifo_mode (FIFO is in use,
or FIFO bypass).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Len Brown [Wed, 20 Jan 2010 06:26:22 +0000 (01:26 -0500)]
Merge branch 'bugzilla-14954' into release
Len Brown [Wed, 20 Jan 2010 06:23:27 +0000 (01:23 -0500)]
Merge branch 'misc' into release
Len Brown [Wed, 20 Jan 2010 06:23:18 +0000 (01:23 -0500)]
Merge branch 'osc-bugfix' into release
Len Brown [Wed, 20 Jan 2010 06:23:01 +0000 (01:23 -0500)]
Merge branch 'eeepc-laptop' into release
Len Brown [Wed, 20 Jan 2010 06:20:36 +0000 (01:20 -0500)]
Merge branch 'ec' into release
Pekka Enberg [Tue, 19 Jan 2010 17:26:11 +0000 (19:26 +0200)]
perf kmem: Print usage help for unknown commands
This patch fixes "perf kmem" to print usage help instead of
doing nothing.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
LKML-Reference: <
1263921971-10782-1-git-send-email-penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Pekka Enberg [Tue, 19 Jan 2010 17:23:23 +0000 (19:23 +0200)]
perf kmem: Increase "Hit" column length
It's fairly easy to overflow the "Hit" column with just few
seconds of tracing so increase the column length to avoid broken
formatting.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
LKML-Reference: <
1263921803-10214-1-git-send-email-penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Len Brown [Wed, 20 Jan 2010 06:15:21 +0000 (01:15 -0500)]
Merge branch 'bugzilla-15064' into release
Len Brown [Wed, 20 Jan 2010 06:14:57 +0000 (01:14 -0500)]
Merge branch 'bugzilla-14858' into release
Len Brown [Wed, 20 Jan 2010 06:14:50 +0000 (01:14 -0500)]
Merge branch 'bugzilla-14483' into release
Len Brown [Wed, 20 Jan 2010 06:14:41 +0000 (01:14 -0500)]
Merge branch 'bugzilla-13577-video' into release
Len Brown [Wed, 20 Jan 2010 06:14:30 +0000 (01:14 -0500)]
Merge branch 'acpi-pad' into release
Len Brown [Wed, 20 Jan 2010 04:29:09 +0000 (23:29 -0500)]
ACPI: delete acpi_processor_power_verify_c2()
no functional change -- cleanup only.
acpi_processor_power_verify_c2() was nearly empty due to a previous patch,
so expand its remains into its one caller and delete it.
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Wed, 20 Jan 2010 04:10:04 +0000 (23:10 -0500)]
ACPI: allow C3 > 1000usec
Do for C3 what the previous patch did for C2.
The C2 patch was in response to a highly visible
and multiply reported C-state/turbo failure,
while this change has no bug report in-hand.
This will enable C3 in Linux on systems where BIOS
overstates C3 latency in _CST. It will also enable
future systems which may actually have C3 > 1000usec.
Linux has always ignored ACPI BIOS C3 with exit latency > 1000 usec,
and the ACPI spec is clear that is correct FADT-supplied C3.
However, the ACPI spec explicitly states that _CST-supplied C-states
have no latency limits.
So move the 1000usec C3 test out of the code shared
by FADT and _CST code-paths, and into the FADT-specific path.
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Wed, 20 Jan 2010 03:41:14 +0000 (22:41 -0500)]
ACPI: enable C2 and Turbo-mode on Nehalem notebooks on A/C
Linux has always ignored ACPI BIOS C2 with exit latency > 100 usec,
and the ACPI spec is clear that is correct FADT-supplied C2.
However, the ACPI spec explicitly states that _CST-supplied C-states
have no latency limits.
So move the 100usec C2 test out of the code shared
by FADT and _CST code-paths, and into the FADT-specific path.
This bug has not been visible until Nehalem, which advertises
a CPU-C2 worst case exit latency on servers of 205usec.
That (incorrect) figure is being used by BIOS writers
on mobile Nehalem systems for the AC configuration.
Thus, Linux ignores C2 leaving just C1, which is
saves less power, and also impacts performance
by preventing the use of turbo mode.
http://bugzilla.kernel.org/show_bug.cgi?id=15064
Tested-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Darren Jenkins [Tue, 12 Jan 2010 12:37:07 +0000 (23:37 +1100)]
ACPI: power_meter: remove double kfree()
resource->domain_devices can be double kfree()'d in a couple of places.
Fix this by setting num_domain_devices = 0 after the kfree().
Coverity CID: 13356, 13355, 13354
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Tue, 19 Jan 2010 23:55:41 +0000 (16:55 -0700)]
ACPI: processor: restrict early _PDC to opt-in platforms
Commit
78f1699 (ACPI: processor: call _PDC early) blindly walks
the namespace and calls _PDC on every processor object it finds.
This change may cause issues on platforms that declare dummy
values for SSDTs on non-present processors (disabled in MADT).
When we call _PDC and dynamically attempt to execute the AML
Load() op on these dummy SSDTs, there's no telling what might
happen.
Rather than finding every platform that has bogus SSDTs, restrict
early _PDC calls to platforms that are known to need early
evaluation of _PDC.
This is a minimal, temporary fix (given the context of the
current release cycle). A real solution of checking the MADT for
non-present processors will be written for the next merge window.
References:
http://bugzilla.kernel.org/show_bug.cgi?id=14710
http://bugzilla.kernel.org/show_bug.cgi?id=14954
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Dan Carpenter [Tue, 19 Jan 2010 09:34:32 +0000 (12:34 +0300)]
ecryptfs: use after free
The "full_alg_name" variable is used on a couple error paths, so we
shouldn't free it until the end.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Julia Lawall [Sat, 16 Jan 2010 16:00:26 +0000 (17:00 +0100)]
ecryptfs: Eliminate useless code
The variable lower_dentry is initialized twice to the same (side effect-free)
expression. Drop one initialization.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@forall@
idexpression *x;
identifier f!=ERR_PTR;
@@
x = f(...)
... when != x
(
x = f(...,<+...x...+>,...)
|
* x = f(...)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Erez Zadok [Mon, 4 Jan 2010 23:17:02 +0000 (18:17 -0500)]
ecryptfs: fix interpose/interpolate typos in comments
Signed-off-by: Erez Zadok <ezk@cs.sunysb.edu>
Acked-by: Dustin Kirkland <kirkland@canonical.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Erez Zadok [Sun, 6 Dec 2009 23:51:15 +0000 (18:51 -0500)]
ecryptfs: pass matching flags to interpose as defined and used there
ecryptfs_interpose checks if one of the flags passed is
ECRYPTFS_INTERPOSE_FLAG_D_ADD, defined as 0x00000001 in ecryptfs_kernel.h.
But the only user of ecryptfs_interpose to pass a non-zero flag to it, has
hard-coded the value as "1". This could spell trouble if any of these values
changes in the future.
Signed-off-by: Erez Zadok <ezk@cs.sunysb.edu>
Cc: Dustin Kirkland <kirkland@canonical.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Erez Zadok [Sun, 6 Dec 2009 23:05:30 +0000 (18:05 -0500)]
ecryptfs: remove unnecessary d_drop calls in ecryptfs_link
Unnecessary because it would unhash perfectly valid dentries, causing them
to have to be re-looked up the next time they're needed, which presumably is
right after.
Signed-off-by: Aseem Rastogi <arastogi@cs.sunysb.edu>
Signed-off-by: Shrikar archak <shrikar84@gmail.com>
Signed-off-by: Erez Zadok <ezk@cs.sunysb.edu>
Cc: Saumitra Bhanage <sbhanage@cs.sunysb.edu>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Erez Zadok [Sun, 6 Dec 2009 02:17:09 +0000 (21:17 -0500)]
ecryptfs: don't ignore return value from lock_rename
Signed-off-by: Erez Zadok <ezk@cs.sunysb.edu>
Cc: Dustin Kirkland <kirkland@canonical.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Erez Zadok [Thu, 3 Dec 2009 18:35:27 +0000 (13:35 -0500)]
ecryptfs: initialize private persistent file before dereferencing pointer
Ecryptfs_open dereferences a pointer to the private lower file (the one
stored in the ecryptfs inode), without checking if the pointer is NULL.
Right afterward, it initializes that pointer if it is NULL. Swap order of
statements to first initialize. Bug discovered by Duckjin Kang.
Signed-off-by: Duckjin Kang <fromdj2k@gmail.com>
Signed-off-by: Erez Zadok <ezk@cs.sunysb.edu>
Cc: Dustin Kirkland <kirkland@canonical.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Tyler Hicks [Tue, 3 Nov 2009 20:56:06 +0000 (14:56 -0600)]
eCryptfs: Remove mmap from directory operations
Adrian reported that mkfontscale didn't work inside of eCryptfs mounts.
Strace revealed the following:
open("./", O_RDONLY|O_NONBLOCK|O_LARGEFILE|O_DIRECTORY|O_CLOEXEC) = 3
fcntl64(3, F_GETFD) = 0x1 (flags FD_CLOEXEC)
open("./fonts.scale", O_WRONLY|O_CREAT|O_TRUNC, 0666) = 4
getdents(3, /* 80 entries */, 32768) = 2304
open("./.", O_RDONLY) = 5
fcntl64(5, F_SETFD, FD_CLOEXEC) = 0
fstat64(5, {st_mode=S_IFDIR|0755, st_size=16384, ...}) = 0
mmap2(NULL, 16384, PROT_READ, MAP_PRIVATE, 5, 0) = 0xb7fcf000
close(5) = 0
--- SIGBUS (Bus error) @ 0 (0) ---
+++ killed by SIGBUS +++
The mmap2() on a directory was successful, resulting in a SIGBUS
signal later. This patch removes mmap() from the list of possible
ecryptfs_dir_fops so that mmap() isn't possible on eCryptfs directory
files.
https://bugs.launchpad.net/ecryptfs/+bug/400443
Reported-by: Adrian C. <anrxc@sysphere.org>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Tyler Hicks [Wed, 4 Nov 2009 08:48:01 +0000 (02:48 -0600)]
eCryptfs: Add getattr function
The i_blocks field of an eCryptfs inode cannot be trusted, but
generic_fillattr() uses it to instantiate the blocks field of a stat()
syscall when a filesystem doesn't implement its own getattr(). Users
have noticed that the output of du is incorrect on newly created files.
This patch creates ecryptfs_getattr() which calls into the lower
filesystem's getattr() so that eCryptfs can use its kstat.blocks value
after calling generic_fillattr(). It is important to note that the
block count includes the eCryptfs metadata stored in the beginning of
the lower file plus any padding used to fill an extent before
encryption.
https://bugs.launchpad.net/ecryptfs/+bug/390833
Reported-by: Dominic Sacré <dominic.sacre@gmx.de>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Tyler Hicks [Wed, 14 Oct 2009 21:18:27 +0000 (16:18 -0500)]
eCryptfs: Use notify_change for truncating lower inodes
When truncating inodes in the lower filesystem, eCryptfs directly
invoked vmtruncate(). As Christoph Hellwig pointed out, vmtruncate() is
a filesystem helper function, but filesystems may need to do more than
just a call to vmtruncate().
This patch moves the lower inode truncation out of ecryptfs_truncate()
and renames the function to truncate_upper(). truncate_upper() updates
an iattr for the lower inode to indicate if the lower inode needs to be
truncated upon return. ecryptfs_setattr() then calls notify_change(),
using the updated iattr for the lower inode, to complete the truncation.
For eCryptfs functions needing to truncate, ecryptfs_truncate() is
reintroduced as a simple way to truncate the upper inode to a specified
size and then truncate the lower inode accordingly.
https://bugs.launchpad.net/bugs/451368
Reported-by: Christoph Hellwig <hch@lst.de>
Acked-by: Dustin Kirkland <kirkland@canonical.com>
Cc: ecryptfs-devel@lists.launchpad.net
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Tony Lindgren [Tue, 19 Jan 2010 22:42:08 +0000 (23:42 +0100)]
ARM: 5888/1: arm: Update comments in cacheflush.h and remove unnecessary V6 and V7 comments
The comments in cacheflush.h should follow what's in
struct cpu_cache_fns. The comments for V6 and V7 are
unnecessary.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>