OSDN Git Service
Hans de Goede [Wed, 25 Apr 2012 15:17:19 +0000 (12:17 -0300)]
[media] gspca_pac7311: Adjust control scales to match registers
Now that the pac7302 and pac7311 drivers are split, they no longer
share there control settings, so there is no need to scale the controls
to register values, instead make them reflect the registers directly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 18 Apr 2012 09:12:57 +0000 (06:12 -0300)]
[media] gspca_pac7311: Make sure exposure changes get applied immediately
It turns out that the flush to sensor command needs to be done per register
bank. We were missing one such flush in set_exposure, causing exposure changes
to only show up when another setting in the same bank also got changed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 25 Apr 2012 15:00:49 +0000 (12:00 -0300)]
[media] gspca_pac73xx: Remove comments from before the 7302 / 7311 separation
The pac7302 and pac7311 driver still contains some comments from before
they were separated, such as marking certain functions 7302 or 7311 only,
with the new split drivers these make no sense, remove them.
Also removed the empty/unused sd_stop0 function from pac7311.c
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Fri, 27 Apr 2012 14:32:24 +0000 (11:32 -0300)]
[media] gspca/autogain_functions.h: Allow users to declare what they want
Allow users of gspca/autogain_functions.h to declare which of the autogain
algoritms they are going to use. This allows us to remove the hacks from
drivers which don't use coarse_grained_expo_autogain.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Sun, 8 Apr 2012 14:04:30 +0000 (11:04 -0300)]
[media] stk-webcam: Don't flip the image by default
Prior to this patch the stk-webcam driver was enabling the vflip and mirror
bits in the sensor by default. Which only is the right thing to do if the
sensor is actually mounted upside down, which it usually is not.
Actually we've received upside down reports for both usb-ids which this
driver supports, one for an "ASUSTeK Computer Inc." "A3H" laptop with
a build in 174f:a311 webcam, and one for an "To Be Filled By O.E.M."
"Z96FM" laptop with a build in 05e1:0501 webcam.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 27 Apr 2012 21:39:37 +0000 (18:39 -0300)]
[media] radio-mr800: add hardware seek support
Added hardware seek support based on information gleaned from the
GPLv2 driver available here:
http://sourceforge.net/projects/av-usbradio/
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 27 Apr 2012 16:28:34 +0000 (13:28 -0300)]
[media] radio-mr800: add support for stereo and signal detection
Thanks to an older driver by Faidon Liambotis <paravoid@debian.org> (as noted
in the radio-mr800 comment block at the start) for figuring out how to get the
signal/stereo state.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 27 Apr 2012 15:30:40 +0000 (12:30 -0300)]
[media] radio-mr800: cleanup and have it comply to the V4L2 API
Implement the control framework and update to the latest V4L2 framework.
The v4l2-compliance tool now runs without errors.
Fixed bad g/s_tuner handling with respect to mono/stereo.
Support control events.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 28 Apr 2012 11:09:48 +0000 (08:09 -0300)]
[media] radio-isa: fix memory leak
If there is an error when creating controls the v4l2_ctrl_handler_free
function must be called.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 18 Apr 2012 09:47:02 +0000 (06:47 -0300)]
[media] radio-keene: support suspend/resume
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 20 Apr 2012 12:51:31 +0000 (09:51 -0300)]
[media] ivtv: set max/step to 0 for PTS and FRAME controls
When creating 64 bit integer controls make sure the max and step
values are 0 (as 64 bit controls do not have ranges).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 27 Apr 2012 11:13:26 +0000 (08:13 -0300)]
[media] dsbr100: clean up and update to the latest v4l2 framework
This driver now complies with the v4l2-compliance tests and uses the v4l2
frameworks correctly.
It has been tested with the radio-keene FM transmitter as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-François Moine [Sat, 24 Mar 2012 12:33:42 +0000 (09:33 -0300)]
[media] gspca - sn9c20x: Change the exposure setting of Omnivision sensors
The exposure of Omnivision sensors is defined by the registers 07, 10 and 04.
This patch updates the registers 10 and 04 before using the registers 2d
and 2e (dummy lines).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-François Moine [Sat, 24 Mar 2012 12:28:39 +0000 (09:28 -0300)]
[media] gspca - sn9c20x: Don't do sensor update before the capture is started
Telling the bridge to update the sensor when setting the exposure or the gain
is not needed when the image transfer is not started.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-François Moine [Sat, 24 Mar 2012 12:23:56 +0000 (09:23 -0300)]
[media] gspca - sn9c20x: Set the i2c interface speed
The i2c interface speed was set to 400 Kb/s while it is 100 Kb/s
for most sensors.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-François Moine [Sat, 24 Mar 2012 12:20:25 +0000 (09:20 -0300)]
[media] gspca - sn9c20x: Define more tables as constant
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-François Moine [Sat, 24 Mar 2012 12:17:37 +0000 (09:17 -0300)]
[media] gspca - sn9c20x: Add the sensor mt9vprb to the sensor ident table
The table did not contain the sensor mt9vprb.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-François Moine [Sat, 24 Mar 2012 12:16:14 +0000 (09:16 -0300)]
[media] gspca - sn9c20x: Change the number of the sensor mt9vprb
This avoid skips in switch statements.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-François Moine [Sat, 24 Mar 2012 12:14:01 +0000 (09:14 -0300)]
[media] gspca - ov519: Add more information about probe problems
The error messages in stable kernel releases must be output by 'pr_err'.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Thu, 22 Mar 2012 16:55:05 +0000 (13:55 -0300)]
[media] smsusb: add autodetection support for USB ID 2040:c0a0
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Thu, 26 Apr 2012 10:39:14 +0000 (07:39 -0300)]
[media] V4L2 Spec: fix typo
V4L2_CID_JPEG_COMPRESION_QUALITY -> V4L2_CID_JPEG_COMPRESSION_QUALITY
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Julia Lawall [Sun, 22 Apr 2012 10:54:42 +0000 (07:54 -0300)]
[media] drivers/media/video/au0828/au0828-video.c: add missing video_device_release
At the point of the call to video_register_device, both dev->vbi_dev and
dev->vdev have been allocated, and so should be freed on failure. The
error-handling code is moved to the end of the function, to avoid code
duplication.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dan Carpenter [Fri, 20 Apr 2012 12:15:02 +0000 (09:15 -0300)]
[media] ngene: remove an unneeded condition
"stat" is always zero here. The condition used to be needed, but we
shifted stuff around in
0f0b270f90 "[media] ngene: CXD2099AR Common
Interface driver".
This doesn't change how the code works, it's just a bit tidier.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dan Carpenter [Fri, 20 Apr 2012 05:50:45 +0000 (02:50 -0300)]
[media] saa7164: saa7164_vbi_stop_port() returns linux error codes
The saa7164_vbi_stop_port() changes the SAA_ERR_ALREADY_STOPPED result
code to -EIO before returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Guennadi Liakhovetski [Wed, 18 Apr 2012 06:59:58 +0000 (03:59 -0300)]
[media] V4L: fix a compiler warning
Fix the warning:
In file included from /home/lyakh/software/project/24/src/linux-2.6/drivers/media/video/v4l2-subdev.c:29:
linux-2.6/include/media/v4l2-ctrls.h:497: warning: 'struct file' declared inside parameter list
linux-2.6/include/media/v4l2-ctrls.h:497: warning: its scope is only this definition or declaration, which is probably not what you want
linux-2.6/include/media/v4l2-ctrls.h:505: warning: 'struct file' declared inside parameter list
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Thu, 19 Apr 2012 14:44:18 +0000 (11:44 -0300)]
[media] vivi: fix duplicate line
This was inadvertently introduced when the integer menu control was added.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Thu, 19 Apr 2012 15:37:18 +0000 (12:37 -0300)]
[media] v4l2-ctrls.c: zero min/max/step/def values for 64 bit integers
Those fields are meaningless for such control types, and the control framework
should zero them. Otherwise v4l2-compliance will complain about non-zero
min/max/step/def fields.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Thu, 19 Apr 2012 15:36:03 +0000 (12:36 -0300)]
[media] V4L2: drivers implementing vidioc_default should also return -ENOTTY
If the vidioc_default implementation doesn't support the ioctl, then drivers
must return -ENOTTY instead of -EINVAL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Thu, 19 Apr 2012 15:27:56 +0000 (12:27 -0300)]
[media] V4L: fix incorrect refcounting
Both radio-keene and dsbr100 did one v4l2_device_get too many. Thus the refcount
never became 0 and that causes a memory leak.
Also updated the V4L2 framework documentation accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dan Carpenter [Wed, 18 Apr 2012 05:55:51 +0000 (02:55 -0300)]
[media] pluto2: remove some dead code
buf[] is a 4 character array. Perhaps this was some debugging code from
back in the day?
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Marcos Paulo de Souza [Wed, 18 Apr 2012 03:30:03 +0000 (00:30 -0300)]
[media] drivers: media: dvb: ddbridge: ddbridge-code: Remove unneeded include of version.h
The output of "make versioncheck" told us that the file
drivers/media/dvb/ddbridge/ddbridge-code.c has a incorrect include of
version.h:
linux/drivers/media/dvb/ddbridge/ddbridge-core.c: 34 linux/version.h not
needed.
After take a look in the code, we can agree to remove it.
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Marcos Paulo de Souza [Wed, 18 Apr 2012 03:30:04 +0000 (00:30 -0300)]
[media] drivers: media: radio: radio-keene.c: Remove unneeded include of version.h
The output of "make versioncheck" told us that:
drivers/media/radio/radio-keene.c: 31 linux/version.h not needed.
After take a look in the code, we can agree to remove it.
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Marcos Paulo de Souza [Wed, 18 Apr 2012 03:30:05 +0000 (00:30 -0300)]
[media] drivers: media: video: adp1653.c: Remove unneeded include of version.h
The output of "make versioncheck" told us that:
drivers/media/video/adp1653.c: 37 linux/version.h not needed.
After we take a look at the code, we can afree to remove it.
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Thu, 19 Apr 2012 19:42:36 +0000 (16:42 -0300)]
[media] tm6000: don't use KERNEL_VERSION
As reported by Marcos:
> The output of "make versioncheck" told us that:
>
> drivers/staging/media/easycap/easycap_ioctl.c: 2442: need linux/version.h
Now that drivers/media/video/v4l2-ioctl.c fills cap->version:
case VIDIOC_QUERYCAP:
{
struct v4l2_capability *cap = (struct v4l2_capability *)arg;
if (!ops->vidioc_querycap)
break;
cap->version = LINUX_VERSION_CODE;
V4L2 drivers that use video_ioctl2() shouldn't initialize it anymore.
Reported-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Thu, 19 Apr 2012 19:35:27 +0000 (16:35 -0300)]
[media] tlg2300: Remove usage of KERNEL_VERSION()
As reported by Marcos:
On 04-18-2012 01:30, Marcos Paulo de Souza wrote:
> The output of "make versioncheck" told us that:
>
> drivers/media/video/tlg2300/pd-video.c: 1669: need linux/version.h
>
> If we take a look at the code, we can see that this file uses the macro
> KERNEL_VERSION.
The V4L2 core now fills it automatically, so drivers shouldn't touch on
cap->version anymore.
Reported by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Gianluca Gennari [Sat, 14 Apr 2012 12:14:07 +0000 (09:14 -0300)]
[media] dib0700: add new USB PID for the Elgato EyeTV DTT stick
Reported working here:
http://ubuntuforums.org/archive/index.php/t-
1510188.html
http://ubuntuforums.org/archive/index.php/t-
1756828.html
https://sites.google.com/site/slackwarestuff/home/elgato-eyetv
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tim Gardner [Thu, 12 Apr 2012 20:23:21 +0000 (17:23 -0300)]
[media] video: vicam: Add MODULE_FIRMWARE
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tim Gardner [Thu, 12 Apr 2012 20:00:07 +0000 (17:00 -0300)]
[media] staging: go7007: Add MODULE_FIRMWARE
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Gianluca Gennari [Thu, 12 Apr 2012 11:46:51 +0000 (08:46 -0300)]
[media] dib7000p: remove duplicate code and comment
Remove duplicate code and comment, probably due to a patch applied twice.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Tue, 17 Apr 2012 11:41:58 +0000 (08:41 -0300)]
[media] videodev2.h: Fix VIDIOC_QUERYMENU ioctl regression
Fixes a regression in VIDIOC_QUERYMENU introduced when the __s64 value
field was added to the union. On a 64-bit system this will change the
size of this v4l2_querymenu structure from 44 to 48 bytes, thus
breaking the ABI. By adding the packed attribute it is working again.
Tested on both 64 and 32 bit systems.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Mon, 9 Apr 2012 21:51:08 +0000 (18:51 -0300)]
[media] au8522_common: dont EXPORT_SYMBOL(au8522_led_gpio_enable)
This function is only called from within au8522_common.c - mark it static.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Mon, 9 Apr 2012 18:50:23 +0000 (15:50 -0300)]
[media] au8522_common: add missing MODULE_LICENSE
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Fri, 27 Jan 2012 16:18:29 +0000 (13:18 -0300)]
[media] au8522: build ATV/DTV demodulators as separate modules
au8522_dig.o and au8522_decoder.o function independentantly
of each other, each for a different hardware function using
a different software subsystem api, each with its own set
of subsystem module dependencies.
Since these drivers do not depend on each other, and it is
in fact possible to build hardware designs using one function
and not the other, lets split this module into two, allowing
system integrators to enable the hardware without dragging in
undesired dependencies.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Mon, 9 Apr 2012 00:39:56 +0000 (21:39 -0300)]
[media] au0828-dvb: attach tuner based on dev->board.tuner_type on hvr950q
We can tell from the eeprom whether we have a xc5000a or xc5000c.
Attach the correct tuner based on this information.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Mon, 16 Apr 2012 18:21:51 +0000 (15:21 -0300)]
[media] xc5000: xtal_khz should be a u16 rather than a u32
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Mon, 16 Apr 2012 18:06:45 +0000 (15:06 -0300)]
[media] xc5000: log firmware upload failures in xc5000_fwupload
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Mon, 16 Apr 2012 17:59:32 +0000 (14:59 -0300)]
[media] xc5000: support 32MHz & 31.875MHz xtal using the 41.024.5 firmware
Rather than loading firmware specific for the xtal frequency, just use
the standard firmware and set the xtal frequency after firmware upload.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Thu, 19 Apr 2012 12:23:28 +0000 (09:23 -0300)]
Merge tag 'v3.4-rc3' into staging/for_v3.5
* tag 'v3.4-rc3': (3755 commits)
Linux 3.4-rc3
x86-32: fix up strncpy_from_user() sign error
ARM: 7386/1: jump_label: fixup for rename to static_key
ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
PCI: Fix regression in pci_restore_state(), v3
SCSI: Fix error handling when no ULD is attached
ARM: OMAP: clock: cleanup CPUfreq leftovers, fix build errors
ARM: dts: remove blank interrupt-parent properties
ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
do not export kernel's NULL #define to userspace
ARM: EXYNOS: Remove broken config values for touchscren for NURI board
ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
ARM: EXYNOS: fix regulator name for NURI board
ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
cpufreq: OMAP: fix build errors: depends on ARCH_OMAP2PLUS
sparc64: Eliminate obsolete __handle_softirq() function
sparc64: Fix bootup crash on sun4v.
ARM: msm: Fix section mismatches in proc_comm.c
...
Xi Wang [Mon, 9 Apr 2012 20:15:45 +0000 (17:15 -0300)]
[media] zoran: fix integer overflow in setup_window()
`clipcount' is from userspace and thus needs validation. Otherwise,
a large `clipcount' could overflow the vmalloc() size, leading to
out-of-bounds access.
| setup_window()
| zoran_s_fmt_vid_overlay()
| __video_do_ioctl()
| video_ioctl2()
Use 2048 as the maximum `clipcount'. Also change the corresponding
parameter type to `unsigned int'.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jesper Juhl [Mon, 9 Apr 2012 19:50:04 +0000 (16:50 -0300)]
[media] s2255drv: Remove redundant NULL test before release_firmware()
release_firmware() tests for NULL pointers on its own - there's no
reason to do an explicit check before calling the function.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jesper Juhl [Mon, 9 Apr 2012 19:51:48 +0000 (16:51 -0300)]
[media] staging: as102: Remove redundant NULL check before release_firmware() and pointless comments
release_firmware() deals gracefullt with NULL pointers - it's
redundant to check for them before calling the function.
Also remove a few pointless comments - it's rather obvious from the
code that kfree() free's a buffer and that release_firmware() releases
firmware - comments just stating that add no value.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Xi Wang [Fri, 6 Apr 2012 12:32:37 +0000 (09:32 -0300)]
[media] v4l2-ctrls: fix integer overflow in try_set_ext_ctrls()
A large cs->count from userspace may overflow the allocation size,
leading to memory corruption. try_set_ext_ctrls() can be reached
from subdev_do_ioctl() or __video_do_ioctl().
Use kmalloc_array() to avoid the overflow.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Xi Wang [Fri, 6 Apr 2012 12:32:36 +0000 (09:32 -0300)]
[media] v4l2-ctrls: fix integer overflow in v4l2_g_ext_ctrls()
A large cs->count from userspace may overflow the allocation size,
leading to memory corruption. v4l2_g_ext_ctrls() can be reached
from subdev_do_ioctl() or __video_do_ioctl().
Use kmalloc_array() to avoid the overflow.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Linus Torvalds [Mon, 16 Apr 2012 01:28:29 +0000 (18:28 -0700)]
Linux 3.4-rc3
Linus Torvalds [Mon, 16 Apr 2012 00:35:19 +0000 (17:35 -0700)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"Nothing too disasterous, the biggest thing being the removal of the
regulator support for vcore in the AMBA driver; only one SoC was using
this and it got broken during the last merge window, which then
started causing problems for other people. Mutual agreement was
reached for it to be removed."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7386/1: jump_label: fixup for rename to static_key
ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
ARM: 7383/1: nommu: populate vectors page from paging_init
ARM: 7381/1: nommu: fix typo in mm/Kconfig
ARM: 7380/1: DT: do not add a zero-sized memory property
ARM: 7379/1: DT: fix atags_to_fdt() second call site
ARM: 7366/3: amba: Remove AMBA level regulator support
ARM: 7377/1: vic: re-read status register before dispatching each IRQ handler
ARM: 7368/1: fault.c: correct how the tsk->[maj|min]_flt gets incremented
Linus Torvalds [Mon, 16 Apr 2012 00:23:00 +0000 (17:23 -0700)]
x86-32: fix up strncpy_from_user() sign error
The 'max' range needs to be unsigned, since the size of the user address
space is bigger than 2GB.
We know that 'count' is positive in 'long' (that is checked in the
caller), so we will truncate 'max' down to something that fits in a
signed long, but before we actually do that, that comparison needs to be
done in unsigned.
Bug introduced in commit
92ae03f2ef99 ("x86: merge 32/64-bit versions of
'strncpy_from_user()' and speed it up"). On x86-64 you can't trigger
this, since the user address space is much smaller than 63 bits, and on
x86-32 it works in practice, since you would seldom hit the strncpy
limits anyway.
I had actually tested the corner-cases, I had only tested them on
x86-64. Besides, I had only worried about the case of a pointer *close*
to the end of the address space, rather than really far away from it ;)
This also changes the "we hit the user-specified maximum" to return
'res', for the trivial reason that gcc seems to generate better code
that way. 'res' and 'count' are the same in that case, so it really
doesn't matter which one we return.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rabin Vincent [Sat, 14 Apr 2012 20:51:32 +0000 (21:51 +0100)]
ARM: 7386/1: jump_label: fixup for rename to static_key
c5905afb0 ("static keys: Introduce 'struct static_key'...") renamed
struct jump_label_key to struct static_key. Fixup ARM for this to
eliminate these build warnings:
include/linux/jump_label.h:113:2:
warning: passing argument 1 of 'arch_static_branch' from incompatible pointer type
include/asm/jump_label.h:17:82:
note: expected 'struct jump_label_key *' but argument is of type 'struct static_key *'
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jonathan Austin [Thu, 12 Apr 2012 16:45:25 +0000 (17:45 +0100)]
ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
Currently when ThumbEE is not enabled (!CONFIG_ARM_THUMBEE) the ThumbEE
register states are not saved/restored at context switch. The default state
of the ThumbEE Ctrl register (TEECR) allows userspace accesses to the
ThumbEE Base Handler register (TEEHBR). This can cause unexpected behaviour
when people use ThumbEE on !CONFIG_ARM_THUMBEE kernels, as well as allowing
covert communication - eg between userspace tasks running inside chroot
jails.
This patch sets up TEECR in order to prevent user-space access to TEEHBR
when !CONFIG_ARM_THUMBEE. In this case, tasks are sent SIGILL if they try to
access TEEHBR.
Cc: stable@vger.kernel.org
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Thu, 12 Apr 2012 16:15:08 +0000 (17:15 +0100)]
ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
If a bank of memory spanning the 4GB boundary is added on a !CONFIG_LPAE
kernel then we will hang early during boot since the memory bank will
have wrapped around to zero.
This patch truncates memory banks for !LPAE configurations when the end
address is not representable in 32 bits.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij [Tue, 10 Apr 2012 11:37:42 +0000 (12:37 +0100)]
ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
During booting of cpu1, there is a short window where cpu1
is online, but not active where cpu1 is occupied by waiting
to become active. If cpu0 then decides to schedule something
on cpu1 and wait for it to complete, before cpu0 has set
cpu1 active, we have a deadlock.
Typically it's this CPU frequency transition that happens at
this time, so let's just not wait for it to happen, it will
happen whenever the CPU eventually comes online instead.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rafael J. Wysocki [Sun, 15 Apr 2012 19:40:40 +0000 (21:40 +0200)]
PCI: Fix regression in pci_restore_state(), v3
Commit
26f41062f28d ("PCI: check for pci bar restore completion and
retry") attempted to address problems with PCI BAR restoration on
systems where FLR had not been completed before pci_restore_state() was
called, but it did that in an utterly wrong way.
First off, instead of retrying the writes for the BAR registers only, it
did that for all of the PCI config space of the device, including the
status register (whose value after the write quite obviously need not be
the same as the written one). Second, it added arbitrary delay to
pci_restore_state() even for systems where the PCI config space
restoration was successful at first attempt. Finally, the mdelay(10) it
added to every iteration of the writing loop was way too much of a delay
for any reasonable device.
All of this actually caused resume failures for some devices on Mikko's
system.
To fix the regression, make pci_restore_state() only retry the writes
for BAR registers and only wait if the first read from the register
doesn't return the written value. Additionaly, make it wait for 1 ms,
instead of 10 ms, after every failing attempt to write into config
space.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 15 Apr 2012 18:14:54 +0000 (11:14 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull "ARM: a few more SoC fixes for 3.4-rc" from Olof Johansson:
- A handful of warning and build fixes for Qualcomm MSM
- Build/warning and bug fixes for Samsung Exynos
- A fix from Rob Herring that removes misplaced interrupt-parent
properties from a few device trees
- A fix to OMAP dealing with cpufreq build errors, removing some of the
offending code since it was redundant anyway
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP: clock: cleanup CPUfreq leftovers, fix build errors
ARM: dts: remove blank interrupt-parent properties
ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
ARM: EXYNOS: Remove broken config values for touchscren for NURI board
ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
ARM: EXYNOS: fix regulator name for NURI board
ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
ARM: msm: Fix section mismatches in proc_comm.c
video: msm: Fix section mismatches in mddi.c
arm: msm: trout: fix compile failure
arm: msm: halibut: remove unneeded fixup
ARM: EXYNOS: Add PDMA and MDMA physical base address defines
ARM: S5PV210: Fix compiler warning in dma.c file
ARM: EXYNOS: Fix compile error in exynos5250-cpufreq.c
ARM: EXYNOS: Add missing definition for IRQ_I2S0
ARM: S5PV210: fix unused LDO supply field from wm8994_pdata
Linus Torvalds [Sun, 15 Apr 2012 18:14:07 +0000 (11:14 -0700)]
Merge tag 'sound-3.4' of git://git./linux/kernel/git/tiwai/sound
Pull another round of sound fixes from Takashi Iwai:
"A few regression fixes for Realtek HD-audio codecs, mainly specific to
some laptop models."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix mem leak (and rid us of trailing whitespace).
ALSA: hda/realtek - Add quirk for Mac Pro 5,1 machines
ALSA: hda/realtek - Add a fixup entry for Acer Aspire 8940G
ALSA: hda/realtek - Fix GPIO1 setup for Acer Aspire 4930 & co
ALSA: hda/realtek - Add a few ALC882 model strings back
Martin K. Petersen [Sun, 15 Apr 2012 03:01:28 +0000 (23:01 -0400)]
SCSI: Fix error handling when no ULD is attached
Commit
18a4d0a22ed6 ("[SCSI] Handle disk devices which can not process
medium access commands") introduced a bug in which we would attempt to
dereference the scsi driver even when the device had no ULD attached.
Ensure that a driver is registered and make the driver accessor function
more resilient to errors during device discovery.
Reported-by: Elric Fu <elricfu1@gmail.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Sun, 15 Apr 2012 00:50:45 +0000 (17:50 -0700)]
Merge branch 'v3.4-samsung-fixes-2' of git://git./linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.4-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
ARM: EXYNOS: Remove broken config values for touchscren for NURI board
ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
ARM: EXYNOS: fix regulator name for NURI board
ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
ARM: EXYNOS: Add PDMA and MDMA physical base address defines
ARM: S5PV210: Fix compiler warning in dma.c file
ARM: EXYNOS: Fix compile error in exynos5250-cpufreq.c
ARM: EXYNOS: Add missing definition for IRQ_I2S0
ARM: S5PV210: fix unused LDO supply field from wm8994_pdata
Kevin Hilman [Fri, 13 Apr 2012 20:52:15 +0000 (13:52 -0700)]
ARM: OMAP: clock: cleanup CPUfreq leftovers, fix build errors
Now that we have OPP layer, and OMAP CPUfreq driver is using it, we no
longer need/use the clock framework code for filling up CPUfreq
tables. Remove it.
Removing this code also eliminates build errors when CPU_FREQ_TABLE
support is not enabled.
Thanks to Russell King for pointing out the parts I missed under
plat-omap in the original version and also pointing out the build
errors when CPUFREQ_TABLE support was not enabled.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Rob Herring [Thu, 12 Apr 2012 15:17:28 +0000 (10:17 -0500)]
ARM: dts: remove blank interrupt-parent properties
These were incorrectly introduced and can cause problems for of_irq_init.
The correct way to define a root controller is no interrupt-parent set at
all or the interrupt-parent is set to the root controller itself when
inherited from a parent node.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sun, 15 Apr 2012 00:44:21 +0000 (17:44 -0700)]
Merge branch 'msm-fix' of git://git./linux/kernel/git/davidb/linux-msm into fixes
From David Brown:
"Here are some fixes for msm that fix problems caused by the latest
ARM code. The ones from Daniel remove unneeded fixups that now
cause compilation failures. Mine fix section mismatches, that were
incompletely fixed earlier."
* 'msm-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Fix section mismatches in proc_comm.c
video: msm: Fix section mismatches in mddi.c
arm: msm: trout: fix compile failure
arm: msm: halibut: remove unneeded fixup
Sachin Kamat [Sat, 14 Apr 2012 14:53:51 +0000 (07:53 -0700)]
ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
Add config dependency for Exynos4 and Exynos5 device tree enabled machine
files on config options ARCH_EXYNOS4 and ARCH_EXYNOS5 respectively.
Enabling machine support without proper ARCH support enabled is incorrect.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Linus Torvalds [Sat, 14 Apr 2012 14:48:13 +0000 (07:48 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf tool fixes from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf kvm: Finding struct machine fails for PERF_RECORD_MMAP
perf annotate: Validate addr in symbol__inc_addr_samples
perf hists browser: Fix NULL deref in hists browsing code
perf hists: Catch and handle out-of-date hist entry maps.
perf annotate: Fix hist decay
perf top: Add intel_idle to the skip list
Lubos Lunak [Wed, 21 Mar 2012 13:08:24 +0000 (14:08 +0100)]
do not export kernel's NULL #define to userspace
GCC's NULL is actually __null, which allows detecting some questionable
NULL usage and warn about it. Moreover each platform/compiler should
have its own stddef.h anyway (which is different from linux/stddef.h).
So there's no good reason to leak kernel's NULL to userspace and
override what the compiler provides.
Signed-off-by: Luboš Luňák <l.lunak@suse.cz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marek Szyprowski [Tue, 10 Apr 2012 04:10:32 +0000 (21:10 -0700)]
ARM: EXYNOS: Remove broken config values for touchscren for NURI board
The atmel_mxt_ts driver has been extended to support more 'configuration
objects' in commit
81c88a711 ("Input: atmel_mxt_ts - update object list"),
what broke the configuration values for NURI board. These values are
optional anyway, so remove them to get the driver working correctly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Marek Szyprowski [Tue, 10 Apr 2012 04:10:32 +0000 (21:10 -0700)]
ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
On some versions of NURI and UniversalC210 boards, camera clocks are
routed directly to xusbxti clock source. This patch sets the correct
value for this clock to let usb and camera sensors to work correctly and
avoid division by zero on driver's probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Marek Szyprowski [Tue, 10 Apr 2012 04:10:32 +0000 (21:10 -0700)]
ARM: EXYNOS: fix regulator name for NURI board
Regulator names should not contain slash to avoid issues with debugfs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Maurus Cuelenaere [Sat, 14 Apr 2012 14:42:04 +0000 (07:42 -0700)]
ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
When selecting SAMSUNG_PM_DEBUG, it complains about a missing printascii()
function if you do not select DEBUG_LL, so make the former select the latter.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Linus Torvalds [Sat, 14 Apr 2012 02:44:36 +0000 (19:44 -0700)]
Merge branch 'systemh-fixes' of git://git./linux/kernel/git/paulg/linux
Pull system.h fixups for less common arch's from Paul Gortmaker:
"Here is what is hopefully the last of the system.h related fixups.
The fixes for Alpha and ia64 are code relocations consistent with what
was done for the more mainstream architectures. Note that the
diffstat lines removed vs lines added are not the same since I've
fixed some of the whitespace issues in the relocated code blocks.
However they are functionally the same. Compile tested locally, plus
these two have been in linux-next for a while.
There is also a trivial one line system.h related fix for the Tilera
arch from Chris Metcalf to fix an implict include.."
* 'systemh-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
irq_work: fix compile failure on tile from missing include
ia64: populate the cmpxchg header with appropriate code
alpha: fix build failures from system.h dismemberment
Linus Torvalds [Sat, 14 Apr 2012 02:42:56 +0000 (19:42 -0700)]
Merge tag 'fbdev-fixes-for-3.4-1' of git://github.com/schandinat/linux-2.6
Pull fbdev fixes from Florian Tobias Schandinat:
- a compile fix for au1*fb
- a fix to make kyrofb usable on x86_64
- a fix for uvesafb to prevent an oops due to NX-protection
"The fix for kyrofb is a bit large but it's just replacing "unsigned
long" by "u32" for 64 bit compatibility."
* tag 'fbdev-fixes-for-3.4-1' of git://github.com/schandinat/linux-2.6:
video:uvesafb: Fix oops that uvesafb try to execute NX-protected page
fbdev: fix au1*fb builds
kyrofb: fix on x86_64
Linus Torvalds [Sat, 14 Apr 2012 02:41:27 +0000 (19:41 -0700)]
Merge branch 'for-linus-min' of git://git./linux/kernel/git/mason/linux-btrfs
Pull the minimal btrfs branch from Chris Mason:
"We have a use-after-free in there, along with errors when mount -o
discard is enabled, and a BUG_ON(we should compile with UP more
often)."
* 'for-linus-min' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: use commit root when loading free space cache
Btrfs: fix use-after-free in __btrfs_end_transaction
Btrfs: check return value of bio_alloc() properly
Btrfs: remove lock assert from get_restripe_target()
Btrfs: fix eof while discarding extents
Btrfs: fix uninit variable in repair_eb_io_failure
Revert "Btrfs: increase the global block reserve estimates"
Linus Torvalds [Sat, 14 Apr 2012 01:45:13 +0000 (18:45 -0700)]
Merge branch 'for-3.4/drivers' of git://git.kernel.dk/linux-block
Pull block driver bits from Jens Axboe:
- A series of fixes for mtip32xx. Most from Asai at Micron, but also
one from Greg, getting rid of the dependency on PCIE_HOTPLUG.
- A few bug fixes for xen-blkfront, and blkback.
- A virtio-blk fix for Vivek, making resize actually work.
- Two fixes from Stephen, making larger transfers possible on cciss.
This is needed for tape drive support.
* 'for-3.4/drivers' of git://git.kernel.dk/linux-block:
block: mtip32xx: remove HOTPLUG_PCI_PCIE dependancy
mtip32xx: dump tagmap on failure
mtip32xx: fix handling of commands in various scenarios
mtip32xx: Shorten macro names
mtip32xx: misc changes
mtip32xx: Add new sysfs entry 'status'
mtip32xx: make setting comp_time as common
mtip32xx: Add new bitwise flag 'dd_flag'
mtip32xx: fix error handling in mtip_init()
virtio-blk: Call revalidate_disk() upon online disk resize
xen/blkback: Make optional features be really optional.
xen/blkback: Squash the discard support for 'file' and 'phy' type.
mtip32xx: fix incorrect value set for drv_cleanup_done, and re-initialize and start port in mtip_restart_port()
cciss: Fix scsi tape io with more than 255 scatter gather elements
cciss: Initialize scsi host max_sectors for tape drive support
xen-blkfront: make blkif_io_lock spinlock per-device
xen/blkfront: don't put bdev right after getting it
xen-blkfront: use bitmap_set() and bitmap_clear()
xen/blkback: Enable blkback on HVM guests
xen/blkback: use grant-table.c hypercall wrappers
Linus Torvalds [Sat, 14 Apr 2012 01:07:19 +0000 (18:07 -0700)]
Merge branch 'for-3.4/core' of git://git.kernel.dk/linux-block
Pull block core bits from Jens Axboe:
"It's a nice and quiet round this time, since most of the tricky stuff
has been pushed to 3.5 to give it more time to mature. After a few
hectic block IO core changes for 3.3 and 3.2, I'm quite happy with a
slow round.
Really minor stuff in here, the only real functional change is making
the auto-unplug threshold a per-queue entity. The threshold is set so
that it's low enough that we don't hold off IO for too long, but still
big enough to get a nice benefit from the batched insert (and hence
queue lock cost reduction). For raid configurations, this currently
breaks down."
* 'for-3.4/core' of git://git.kernel.dk/linux-block:
block: make auto block plug flush threshold per-disk based
Documentation: Add sysfs ABI change for cfq's target latency.
block: Make cfq_target_latency tunable through sysfs.
block: use lockdep_assert_held for queue locking
block: blk_alloc_queue_node(): use caller's GFP flags instead of GFP_KERNEL
Kevin Hilman [Fri, 13 Apr 2012 20:32:30 +0000 (13:32 -0700)]
cpufreq: OMAP: fix build errors: depends on ARCH_OMAP2PLUS
The OMAP driver needs a 'depends on ARCH_OMAP2PLUS' since it only
builds for OMAP2+ platforms.
This 'depends on' was in the original patch from Russell King, but was
erroneously removed by me when making this option user-selectable in
commit
b09db45c (cpufreq: OMAP driver depends CPUfreq tables.) This
patch remedies that.
Apologies to Russell King for breaking his originally working patch.
Also, thanks to Grazvydas Ignotas for reporting the same problem.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 13 Apr 2012 19:41:21 +0000 (12:41 -0700)]
Merge git://git./linux/kernel/git/davem/sparc
Pull sparc fixes from David Miller.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Eliminate obsolete __handle_softirq() function
sparc64: Fix bootup crash on sun4v.
Linus Torvalds [Fri, 13 Apr 2012 19:19:41 +0000 (12:19 -0700)]
Merge tag 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon patches from Guenter Roeck:
"Fix build warnings in four drivers"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (pmbus_core) Fix compiler warning
hwmon: (smsc47m1) Fix compiler warning
hwmon: (acpi_power_meter) Fix compiler warning seen in some configurations
hwmon: (smsc47b397) Fix compiler warning
Linus Torvalds [Fri, 13 Apr 2012 19:18:20 +0000 (12:18 -0700)]
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO bug fixes from Grant Likely:
"Miscellaneous bug fixes to GPIO drivers and for a corner case in the
gpio device tree parsing code."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/exynos: Fix compiler warning in gpio-samsung.c file
gpio: Fix range check in of_gpio_simple_xlate()
gpio: Fix uninitialized variable bit in adp5588_irq_handler
gpio/sodaville: Convert sodaville driver to new irqdomain API
Linus Torvalds [Fri, 13 Apr 2012 19:17:45 +0000 (12:17 -0700)]
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI bug fixes from Grant Likely:
"Miscellaneous driver bug fixes. No major changes in this branch."
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi/imx: prevent NULL pointer dereference in spi_imx_probe()
spi/imx: mark base member in spi_imx_data as __iomem
spi/mpc83xx: fix NULL pdata dereference bug
spi/davinci: Fix DMA API usage in davinci
spi/pL022: include types.h to remove compilation warnings
Paul E. McKenney [Fri, 13 Apr 2012 03:35:13 +0000 (03:35 +0000)]
sparc64: Eliminate obsolete __handle_softirq() function
The invocation of softirq is now handled by irq_exit(), so there is no
need for sparc64 to invoke it on the trap-return path. In fact, doing so
is a bug because if the trap occurred in the idle loop, this invocation
can result in lockdep-RCU failures. The problem is that RCU ignores idle
CPUs, and the sparc64 trap-return path to the softirq handlers fails to
tell RCU that the CPU must be considered non-idle while those handlers
are executing. This means that RCU is ignoring any RCU read-side critical
sections in those handlers, which in turn means that RCU-protected data
can be yanked out from under those read-side critical sections.
The shiny new lockdep-RCU ability to detect RCU read-side critical sections
that RCU is ignoring located this problem.
The fix is straightforward: Make sparc64 stop manually invoking the
softirq handlers.
Reported-by: Meelis Roos <mroos@linux.ee>
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 13 Apr 2012 18:56:22 +0000 (11:56 -0700)]
sparc64: Fix bootup crash on sun4v.
The DS driver registers as a subsys_initcall() but this can be too
early, in particular this risks registering before we've had a chance
to allocate and setup module_kset in kernel/params.c which is
performed also as a subsyts_initcall().
Register DS using device_initcall() insteal.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: stable@vger.kernel.org
David Brown [Thu, 12 Apr 2012 18:36:50 +0000 (11:36 -0700)]
ARM: msm: Fix section mismatches in proc_comm.c
The change
commit
4416e9eb0b4859b3d28016c5fd0a609bdcbc8a2a
Author: Gregory Bean <gbean@codeaurora.org>
Date: Wed Jul 28 10:22:12 2010 -0700
arm: msm: Fix section mismatch in smd.c.
fixes a section mismatch between the board file and the smd driver's
probe function, however, it misses the additional mismatches between
the probe function and some routines it calls. Fix these up as well.
Signed-off-by: David Brown <davidb@codeaurora.org>
David Brown [Thu, 12 Apr 2012 18:36:50 +0000 (11:36 -0700)]
video: msm: Fix section mismatches in mddi.c
The change
commit
461cbe77d0a4f887c33a3a95ea68a7daf23b4302
Author: Gregory Bean <gbean@codeaurora.org>
Date: Wed Jul 28 10:22:13 2010 -0700
video: msm: Fix section mismatch in mddi.c.
fixes a section mismatch between the board file and the driver's probe
function, however, it misses the additional mismatches between the
probe function and some routines it calls. Fix these up as well.
Signed-off-by: David Brown <davidb@codeaurora.org>
Daniel Walker [Thu, 12 Apr 2012 15:45:37 +0000 (08:45 -0700)]
arm: msm: trout: fix compile failure
Fixes the following warnings,
arch/arm/mach-msm/board-trout.c: In function 'trout_init':
arch/arm/mach-msm/board-trout.c:71: error: 'system_rev' undeclared (first use in this function)
arch/arm/mach-msm/board-trout.c:71: error: (Each undeclared identifier is reported only once
arch/arm/mach-msm/board-trout.c:71: error: for each function it appears in.)
and
arch/arm/mach-msm/board-trout-panel.c: In function 'trout_init_panel':
arch/arm/mach-msm/board-trout-panel.c:267: error: 'system_rev' undeclared (first use in this function)
arch/arm/mach-msm/board-trout-panel.c:267: error: (Each undeclared identifier is reported only once
arch/arm/mach-msm/board-trout-panel.c:267: error: for each function it appears in.)
This came in with the following commit
9f97da78bf018206fb623cd351d454af2f105fe0
which removes asm/system.h
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
cc: David Howells <dhowells@redhat.com>
cc: Bryan Huntsman <bryanh@codeaurora.org>
cc: linux-arm-msm@vger.kernel.org
cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: David Brown <davidb@codeaurora.org>
Daniel Walker [Thu, 12 Apr 2012 04:04:02 +0000 (21:04 -0700)]
arm: msm: halibut: remove unneeded fixup
This old fixup causes a build failure, so I remove it just like in
trout.
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
Chris Metcalf [Wed, 11 Apr 2012 16:21:39 +0000 (12:21 -0400)]
irq_work: fix compile failure on tile from missing include
Building with IRQ_WORK configured results in
kernel/irq_work.c: In function ‘irq_work_run’:
kernel/irq_work.c:110: error: implicit declaration of function ‘irqs_disabled’
The appropriate header just needs to be included.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Paul Gortmaker [Tue, 3 Apr 2012 17:51:35 +0000 (13:51 -0400)]
ia64: populate the cmpxchg header with appropriate code
commit
93f378883cecb9dcb2cf5b51d9d24175906659da
"Fix ia64 build errors (fallout from system.h disintegration)"
introduced arch/ia64/include/asm/cmpxchg.h as a temporary
build fix and stated:
"... leave the migration of xchg() and cmpxchg() to this new
header file for a future patch."
Migrate the appropriate chunks from asm/intrinsics.h and fix
the whitespace issues in the migrated chunk.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Paul Gortmaker [Mon, 2 Apr 2012 20:04:13 +0000 (16:04 -0400)]
alpha: fix build failures from system.h dismemberment
commit
ec2212088c42ff7d1362629ec26dda4f3e8bdad3
"Disintegrate asm/system.h for Alpha"
combined with commit
b4816afa3986704d1404fc48e931da5135820472
"Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h"
introduced the concept of asm/cmpxchg.h but the alpha arch
never got one. Fork the cmpxchg content out of the asm/atomic.h
file to create one.
Some minor whitespace fixups were done on the block of code that
created the new file.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Will Deacon [Thu, 12 Apr 2012 16:16:01 +0000 (17:16 +0100)]
ARM: 7383/1: nommu: populate vectors page from paging_init
Commit
94e5a85b ("ARM: earlier initialization of vectors page") made it
the responsibility of paging_init to initialise the vectors page.
This patch adds a call to early_trap_init for the !CONFIG_MMU case,
placing the vectors at CONFIG_VECTORS_BASE.
Cc: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Thu, 12 Apr 2012 16:12:37 +0000 (17:12 +0100)]
ARM: 7381/1: nommu: fix typo in mm/Kconfig
The description for the CPU_HIGH_VECTOR Kconfig option for nommu builds
doesn't make any sense.
This patch fixes up the trivial grammatical error.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Marc Zyngier [Wed, 11 Apr 2012 13:52:56 +0000 (14:52 +0100)]
ARM: 7380/1: DT: do not add a zero-sized memory property
Some bootloaders are broken enough to expose an ATAG_MEM with
a null size. Converting such tag to a memory node leads to
an unbootable system.
Skip over zero sized ATAG_MEM to avoid this situation.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Marc Zyngier [Wed, 11 Apr 2012 13:52:55 +0000 (14:52 +0100)]
ARM: 7379/1: DT: fix atags_to_fdt() second call site
atags_to_fdt() returns 1 when it fails to find a valid FDT signature.
The CONFIG_ARM_ATAG_DTB_COMPAT code is supposed to retry with another
location, but only does so when the initial call doesn't fail.
Fix this by using the correct condition in the assembly code.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mark Brown [Fri, 13 Apr 2012 12:11:50 +0000 (13:11 +0100)]
ARM: 7366/3: amba: Remove AMBA level regulator support
The AMBA bus regulator support is being used to model on/off switches
for power domains which isn't terribly idiomatic for modern kernels with
the generic power domain code and creates integration problems on platforms
which don't use regulators for their power domains as it's hard to tell
the difference between a regulator that is needed but failed to be provided
and one that isn't supposed to be there (though DT does make that easier).
Platforms that wish to use the regulator API to manage their power domains
can indirect via the power domain interface.
This feature is only used with the vape supply of the db8500 PRCMU
driver which supplies the UARTs and MMC controllers, none of which have
support for managing vcore at runtime in mainline (only pl022 SPI
controller does). Update that supply to have an always_on constraint
until the power domain support for the system is updated so that it is
enabled for these users, this is likely to have no impact on practical
systems as probably at least one of these devices will be active and
cause AMBA to hold the supply on anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ingo Molnar [Fri, 13 Apr 2012 07:47:04 +0000 (09:47 +0200)]
Merge tag 'perf-urgent-for-mingo' of git://git./linux/kernel/git/acme/linux into perf/urgent
Pull various perf tooling fixes from Arnaldo Carvalho de Melo.