OSDN Git Service
Nick Kossifidis [Thu, 30 Apr 2009 19:55:45 +0000 (15:55 -0400)]
ath5k: Read Spur channels from EEPROM
* Read Spur channel information from EEPROM and use default channels
for RF5413 compatible chips that don't have this info on EEPROM.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Thu, 30 Apr 2009 19:55:44 +0000 (15:55 -0400)]
ath5k: Allow user/driver to set txpower
* Now that we have regulatory control enable the driver to set
txpower on hw
* Also use txpower table offset so that we can match
power range set by user/driver with indices on power table.
Tested 2 different cards (a CM9 and an RF5112-based ubnt) and got
the same output using a remote machine to measure per-packet rssi
(conected the cards using attenuators). I also switched between
various tx power levels and i saw an equal power change on the remote
machine (so txpower changes as expected) and verified that we have
the same output on each rate.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 28 Apr 2009 18:14:58 +0000 (20:14 +0200)]
rt2x00: Synchronize initialization with rt2870 driver
Ralink released a new rt2870 driver, these are the obvious
differences I could find. It doesn't same to make my device
work better, but neither does it seem to regress...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 27 Apr 2009 21:58:31 +0000 (23:58 +0200)]
rt2x00: Add new USB ID for rt2800usb
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Wed, 29 Apr 2009 20:33:31 +0000 (23:33 +0300)]
wl12xx: add driver
wl12xx is a driver for TI wl1251 802.11 chipset designed for embedded
devices, supporting both SDIO and SPI busses. Currently the driver
supports only SPI. Adding support 1253 (the 5 GHz version) should be
relatively easy. More information here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?contentId=4711&navigationId=12494&templateId=6123
(Collapsed original sequence of pre-merge patches into single commit for
initial merge. -- JWL)
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 26 Apr 2009 13:47:48 +0000 (15:47 +0200)]
rt2x00: Implement support for rt2800usb
Add support for the rt2800usb chipset.
Current problems:
* Cannot scan 11n AP's
* No TX during first minute after association
* Broken Hardware encryption
Includes various patches from Mattias, Felix, Xose and Axel.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Axel Kollhofer <rain_maker@root-forum.org>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alban Browaeys [Wed, 29 Apr 2009 20:00:23 +0000 (22:00 +0200)]
rt2x00: Style fix for interval defines
Extra parenthesis are not needed in these 2 cases,
all other defines in rt2x00 are done without parenthesis
so just fixup these 2 cases.
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Wed, 29 Apr 2009 11:01:58 +0000 (13:01 +0200)]
ath9k: uninline ath9k_io{read,write}32 routines
The spin_lock handling uses lots of instructions on some archs.
With this patch the size of the ath9k module will be significantly
smaller.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 29 Apr 2009 10:26:17 +0000 (12:26 +0200)]
mac80211: tell driver when idle
When we aren't doing anything in mac80211, we can turn off
much of the hardware, depending on the driver/hw. Not doing
anything, aka being idle, means:
* no monitor interfaces
* no AP/mesh/wds interfaces
* any station interfaces are in DISABLED state
* any IBSS interfaces aren't trying to be in a network
* we aren't trying to scan
By creating a new function that verifies these conditions and calling
it at strategic points where the states of those conditions change,
we can easily make mac80211 tell the driver when we are idle to save
power.
Additionally, this fixes a small quirk where a recalculated powersave
state is passed to the driver even if the hardware is about to stopped
completely.
This patch intentionally doesn't touch radio_enabled because that is
currently implemented to be a soft rfkill which is inappropriate here
when we need to be able to wake up with low latency.
One thing I'm not entirely sure about is this:
phy0: device no longer idle - in use
wlan0: direct probe to AP 00:11:24:91:07:4d try 1
wlan0 direct probe responded
wlan0: authenticate with AP 00:11:24:91:07:4d
wlan0: authenticated
> phy0: device now idle
> phy0: device no longer idle - in use
wlan0: associate with AP 00:11:24:91:07:4d
wlan0: RX AssocResp from 00:11:24:91:07:4d (capab=0x401 status=0 aid=1)
wlan0: associated
Is it appropriate to go into idle state for a short time when we have
just authenticated, but not associated yet? This happens only with the
userspace SME, because we cannot really know how long it will wait
before asking us to associate. Would going idle after a short timeout
be more appropriate? We may need to revisit this, depending on what
happens.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gábor Stefanik [Thu, 23 Apr 2009 17:36:14 +0000 (19:36 +0200)]
mac80211: Warn if the rate controller requests retries for a NO_ACK frame
To deter future rate scaling algorithm writers from requesting NO_ACK
packets to be retried, throw a WARN_ON_ONCE if the algorithm hands us
a try count over 1 for NO_ACK packet.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gábor Stefanik [Thu, 23 Apr 2009 17:36:11 +0000 (19:36 +0200)]
ath9k: Fix handling of retry count of NO_ACK frames
Check for IEEE80211_TX_CTL_NO_ACK instead of is_multicast_ether_addr
when determining whether to use lowest rate without retries.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gábor Stefanik [Thu, 23 Apr 2009 17:36:08 +0000 (19:36 +0200)]
iwlwifi: Fix handling of retry count of NO_ACK frames in iwl-{3945|agn}-rs
Make iwl-{3945|agn}-rs check for IEEE80211_TX_CTL_NO_ACK instead of
is_multicast_ether_addr when determining whether to use the lowest
rate, and set the retry count to 0 (total try count = 1) if
IEEE80211_TX_CTL_NO_ACK is set.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gábor Stefanik [Thu, 23 Apr 2009 18:06:06 +0000 (20:06 +0200)]
mac80211: Fix handling of retry count of NO_ACK frames in PID
Make PID check for IEEE80211_TX_CTL_NO_ACK instead of
is_multicast_ether_addr when determining whether to use the lowest
rate, and set the retry count to 0 (total try count = 1) if
IEEE80211_TX_CTL_NO_ACK is set.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gábor Stefanik [Thu, 23 Apr 2009 17:36:00 +0000 (19:36 +0200)]
mac80211: Fix handling of retry count of NO_ACK frames in minstrel
Make the retry count zero (total try count = 1) for frames with
IEEE80211_TX_CTL_NO_ACK set.
Also remove the check for is_multicast_ether_addr in use_low_rate,
which is redundant because all multicasts have IEEE80211_TX_CTL_NO_ACK
set.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Tue, 28 Apr 2009 02:18:10 +0000 (22:18 -0400)]
ath5k: correct interrupt storm warning
Ben Greear points out that the "too many interrupts" message will
never print in the intended case since the interrupt counter
will be -1 after the loop. Change it to pre-decrement so it will
be 0 on the thousandth iteration.
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 26 Apr 2009 14:09:32 +0000 (16:09 +0200)]
rt2x00: Implement support for 802.11n
Extend rt2x00lib capabilities to support 802.11n,
it still lacks aggregation support, but that can
be added in the future.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 26 Apr 2009 14:08:50 +0000 (16:08 +0200)]
rt2x00: Add support for L2 padding during TX/RX
Some hardware require L2 padding between header and payload
because both must be aligned to a 4-byte boundary. This hardware
also is easier during the RX path since we no longer need to
move the entire payload but rather only the header to remove
the padding (mac80211 only wants the payload to be 4-byte aligned).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 26 Apr 2009 14:08:30 +0000 (16:08 +0200)]
rt2x00: Move iv_len into tx descriptor data
By placing the iv_len into the tx descriptor data and
by passing this data to the crypto IV handlers we can
save multiple calls to ieee80211_get_hdrlen_from_skb()
and some if-statements when copying/removing the IV data
from the outgoing frame.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tobias Klauser [Sun, 26 Apr 2009 12:58:40 +0000 (14:58 +0200)]
ath5k: Storage class should be before const qualifier
commit
8e218fb24faef0bfe95bc91b3c05261e20439527 reverted the previous
patch (commit
925be8a3077351edbf2b59ca689105df214a0792).
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roel Kluin [Sun, 26 Apr 2009 12:40:59 +0000 (14:40 +0200)]
ar9170: wrong test on outlen in ar9170_usb_exec_cmd() ?
remove redundant test: outlen is unsigned
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sun, 26 Apr 2009 09:27:33 +0000 (11:27 +0200)]
cfg80211: Use the correct IE buffer pointer
If the IE buffer was allocated, the pub.information_elements pointer
was also changed to the allocated space. So we must not assume anymore
that the pointer points at the "found" tail.
So if it was allocated previously, take the codebranch that grows the
buffer size (if necessary) and put the data into the allocated buffer.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sat, 25 Apr 2009 20:28:55 +0000 (22:28 +0200)]
cfg80211: Remove unnecessary ksize() call
This removes an unnecessary ksize() call. krealloc() will do this
test internally and won't perform any allocation if the space is
already sufficient to hold the data.
So remove the redundant check.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Sat, 25 Apr 2009 19:32:09 +0000 (21:32 +0200)]
ar9170usb: reset device on resume
This patch takes care of an outstanding comment in
"[PATCH] ar9170usb: fix hang on resume" commit message.
>However, the device does not accept the firmware on resume.
>and it will exit with:
>
>> firmware part 1 upload failed (-71).
>> device is in a bad state. please reconnect it!
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Sat, 25 Apr 2009 19:12:09 +0000 (21:12 +0200)]
p54usb: rework driver for resume
This patch redo the driver code so that p54usb no longer hangs
the kernel on resume.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Sat, 25 Apr 2009 19:11:55 +0000 (21:11 +0200)]
p54usb: remove some dead code
Since "p54: prevent upload of wrong firmwares" we no longer allow
outdated LM86 firmwares to be uploaded on ISL3887 (LM87) devices.
Therefore we can purge this buggy legacy code altogether.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jiri Slaby [Sat, 25 Apr 2009 12:09:23 +0000 (14:09 +0200)]
ath5k: 5211, don't crypt every protected frame
Set null key type even on ar5211, otherwise it en/decrypts every frame with
protected bit set which renders the card unusable on encrypted networks.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrew Morton [Fri, 24 Apr 2009 22:26:02 +0000 (15:26 -0700)]
net/rfkill/rfkill.c: fix build with CONFIG_RFKILL_LEDS=n
net/rfkill/rfkill.c: In function 'update_rfkill_state':
net/rfkill/rfkill.c:99: error: implicit declaration of function 'rfkill_led_trigger'
Caused by
: commit
492301fb5d12e4a77a1010ad2b6f1ed306014123
: Author: Larry Finger <Larry.Finger@lwfinger.net>
: Date: Thu Apr 9 22:14:19 2009 -0500
:
: rfkill: Fix broken rfkill LED in 2.6.30-rc1
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chris Wright [Fri, 24 Apr 2009 21:09:31 +0000 (14:09 -0700)]
cfg80211: remove superfluous !last_request check in reg_device_remove()
Commit
0ad8acaf "cfg80211: fix NULL pointer deference in
reg_device_remove()" added a check that last_request is non-NULL,
rendering the 2nd check superfluous. While there, rearrange the code a
bit so it's a little more straight forward.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Fri, 24 Apr 2009 19:41:18 +0000 (21:41 +0200)]
ar9170: uncomment powermgt case handle
This patch uncomment a few lines that survived the RFCs.
However, there is not much to worry about, since AP mode is
not officially advertised and supported.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Fri, 24 Apr 2009 19:35:57 +0000 (21:35 +0200)]
ar9170: handle otus' A-MPDU density definitions
Otus uses slightly different set of "Minimum MPDU Start Spacing" values
than the 802.11n D2.0 specifies. (the whole table is shifted by one and
therefore the 16us spacing is not officially available!)
And while we're at it, we also initialize our MAC's density register.
So, this annoying _feature_ will not break TX A-MPDU later.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 24 Apr 2009 13:15:25 +0000 (15:15 +0200)]
mac80211: fix probe response processing
Due to the use of a _REQ_DIRECT_PROBE bit, which is
unnecessary (and I wonder why it was done that way),
an interesting situation can arise:
1) we try to probe an access point
2) the AP doesn't response in time
3) we tell userspace that we gave up
4) the AP suddenly responds
5) we auth/assoc with the AP
I've seen 4) happen in testing with hostapd SIGSTOPped,
and when SIGCONTinued it processes the probe requests
that came in and send responses. But 5) is not supposed
to happen after we tell everybody we've given up on the
AP.
To fix this, remove the _REQ_DIRECT_PROBE request bit,
and process probe responses when we're in the relevant
MLME state, namely IEEE80211_STA_MLME_DIRECT_PROBE.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 24 Apr 2009 13:13:54 +0000 (15:13 +0200)]
mac80211_hwsim: fix bogus warning
A typo slipped into my patch to configure beacon intervals
properly -- this warning is supposed to trigger when the
beacon interval is zero, not non-zero.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Thu, 23 Apr 2009 21:00:00 +0000 (00:00 +0300)]
nl80211: Send timeout event on failed direct probe
If the direct probe times out, we need to send the authentication
timeout event to notify SME in the same way as we notify on timeout
with authentication frames since the direct probe is run as part of
the authentication attempt.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 23 Apr 2009 16:52:52 +0000 (18:52 +0200)]
mac80211: add driver ops wrappers
In order to later add tracing or verifications to the driver
calls mac80211 makes, this patch adds static inline wrappers
for all operations.
All calls are now written as
drv_<op>(local, ...);
instead of
local->ops-><op>(&local->hw, ...);
Where necessary, the wrappers also do existence checking and
return default values as appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 23 Apr 2009 14:13:26 +0000 (16:13 +0200)]
mac80211: unify config_interface and bss_info_changed
The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 23 Apr 2009 14:10:04 +0000 (16:10 +0200)]
mac80211: clean up beacon interval settings
We currently have two beacon interval configuration knobs:
hw.conf.beacon_int and vif.bss_info.beacon_int. This is
rather confusing, even though the former is used when we
beacon ourselves and the latter when we are associated to
an AP.
This just deprecates the hw.conf.beacon_int setting in favour
of always using vif.bss_info.beacon_int. Since it touches all
the beaconing IBSS code anyway, we can also add support for
the cfg80211 IBSS beacon interval configuration easily.
NOTE: The hw.conf.beacon_int setting is retained for now due
to drivers still using it -- I couldn't untangle all
drivers, some are updated in this patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 23 Apr 2009 14:01:47 +0000 (16:01 +0200)]
mac80211: fix scan races and rework scanning
There are some places marked
/* XXX maybe racy? */
and they really are racy because there's no locking.
This patch reworks much of the scan code, and introduces proper
locking for the scan request as well as the internal scanning
(which is necessary for IBSS/managed modes). Helper functions
are added to call the scanning code whenever necessary. The
scan deferring is changed to simply queue the scanning work
instead of trying to start the scan in place, the scanning work
will then take care of the rest.
Also, currently when internal scans are requested for an interface
that is trying to associate, we reject such scans. This was not
intended, the mlme code has provisions to scan twice when it can't
find the BSS to associate with right away; this has never worked
properly. Fix this by not rejecting internal scan requests for an
interface that is associating.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 23 Apr 2009 08:38:26 +0000 (10:38 +0200)]
mac80211: internally clear failed scans properly
When the IBSS code wants to scan, but that fails, we can
get stuck in a situation where you can never scan again.
Fix this by properly notifying ourselves when the scan
request has failed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 23 Apr 2009 08:32:36 +0000 (10:32 +0200)]
mac80211: rename max_sleep_interval to max_sleep_period
Kalle points out that max_sleep_interval is somewhat confusing
because the value is measured in beacon intervals, and not in
TU. Rename it to max_sleep_period to be consistent with things
like DTIM period that are also measured in beacon intervals.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 22 Apr 2009 21:02:51 +0000 (23:02 +0200)]
mac80211: fix PS vs. scan race
When somebody changes the PS parameters while scanning
is in progress, we enable PS -- during the scan. This
is clearly not desirable, and we can just abort enabling
PS when scanning since when the scan finishes it will
be taken care of.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 23 Apr 2009 09:48:56 +0000 (11:48 +0200)]
mac80211: fix various problems in ibss code
There are a few problems in the IBSS code:
a) it tries to activate interfaces that are down after scanning
b) it crashes after scanning on an IBSS iface that isn't active
c) since the ssid_len is used as a flag, need to make it visible
only after all other settings are set, this helps protect
against b)
For b), we get a system crash:
wlan0: Creating new IBSS network, BSSID ce:f9:88:76:1e:4d
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<...>] ieee80211_sta_find_ibss+0x294/0x37d [mac80211]
Call Trace:
[<...>] ieee80211_ibss_notify_scan_completed+0x0/0x88 [mac80211]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Greg Kroah-Hartman [Tue, 5 May 2009 04:33:19 +0000 (21:33 -0700)]
net: remove driver_data direct access of struct device from more drivers
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Mon, 4 May 2009 18:12:14 +0000 (11:12 -0700)]
netns 2/2: extract net_create()
net_create() will be used by C/R to create fresh netns on restart.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Mon, 4 May 2009 18:11:38 +0000 (11:11 -0700)]
netns 1/2: don't get/put old netns on CLONE_NEWNET
copy_net_ns() doesn't copy anything, it creates fresh netns, so
get/put of old netns isn't needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Petazzoni [Mon, 4 May 2009 18:08:41 +0000 (11:08 -0700)]
macb: Add support of the netpoll API
With this patch in place, I'm successfully able to use the netconsole
mechanism with the Calao USB-A9263 board, which uses the AT91SAM9263
CPU, which in terms of Ethernet controller is supported by the macb
driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[haavard.skinnemoen@atmel.com: disable_irq() -> local_irq_save()]
[haavard.skinnemoen@atmel.com: convert to net_device_ops]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Mon, 4 May 2009 18:07:36 +0000 (11:07 -0700)]
tcp: extend ECN sysctl to allow server-side only ECN
This should be very safe compared with full enabled, so I see
no reason why it shouldn't be done right away. As ECN can only
be negotiated if the SYN sending party is also supporting it,
somebody in the loop probably knows what he/she is doing. If
SYN does not ask for ECN, the server side SYN-ACK is identical
to what it is without ECN. Thus it's quite safe.
The chosen value is safe w.r.t to existing configs which
choose to currently set manually either 0 or 1 but
silently upgrades those who have not explicitly requested
ECN off.
Whether to just enable both sides comes up time to time but
unless that gets done now we can at least make the servers
aware of ECN already. As there are some known problems to occur
if ECN is enabled, it's currently questionable whether there's
any real gain from enabling clients as servers mostly won't
support it anyway (so we'd hit just the negative sides). After
enabling the servers and getting that deployed, the client end
enable really has some potential gain too.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 3 May 2009 21:43:10 +0000 (14:43 -0700)]
net: Avoid modulus in skb_tx_hash() for forwarding case.
Based almost entirely upon a patch by Eric Dumazet.
The common case is to have num-tx-queues <= num_rx_queues
and even if num_tx_queues is larger it will not be significantly
larger.
Therefore, a subtraction loop is always going to be faster than
modulus.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rami Rosen [Sun, 3 May 2009 08:58:48 +0000 (08:58 +0000)]
ipv4: remove unused macro (FIB_RES_RESET) from ip_fib.h.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Sat, 2 May 2009 23:55:06 +0000 (23:55 +0000)]
ne2k-pci: use dev->addr_len instead of "6"
Spotted a tiny ugliness in a recently posted patch. This patch cuts it out.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/ne2k-pci.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 3 May 2009 21:18:53 +0000 (14:18 -0700)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6
David S. Miller [Sun, 3 May 2009 21:07:43 +0000 (14:07 -0700)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6
Lubomir Rintel [Sat, 2 May 2009 20:52:13 +0000 (13:52 -0700)]
ne2k-pci: Do not register device until initialized.
Doing it in reverse order causes uevent to be sent before
we have a MAC address, which confuses udev.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rabin Vincent [Sat, 2 May 2009 20:49:36 +0000 (13:49 -0700)]
Subject: [PATCH] br2684: restore net_dev initialization
Commit
0ba25ff4c669e5395110ba6ab4958a97a9f96922 ("br2684: convert to
net_device_ops") inadvertently deleted the initialization of the net_dev
pointer in the br2684_dev structure, leading to crashes. This patch
adds it back.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Love [Sat, 2 May 2009 20:48:32 +0000 (13:48 -0700)]
net: Only store high 16 bits of kernel generated filter priorities
The kernel should only be using the high 16 bits of a kernel
generated priority. Filter priorities in all other cases only
use the upper 16 bits of the u32 'prio' field of 'struct tcf_proto',
but when the kernel generates the priority of a filter is saves all
32 bits which can result in incorrect lookup failures when a filter
needs to be deleted or modified.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Williamson [Fri, 1 May 2009 17:31:10 +0000 (17:31 +0000)]
virtio_net: Fix function name typo
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Williamson [Fri, 1 May 2009 17:27:56 +0000 (17:27 +0000)]
virtio_net: Cleanup command queue scatterlist usage
We were avoiding calling sg_init* on scatterlists passed
into virtnet_send_command to prevent extraneous end markers.
This caused build warnings for uninitialized variables.
Cleanup the code to create proper scatterlists.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ken Kawasaki [Sat, 2 May 2009 02:21:26 +0000 (19:21 -0700)]
3c589_cs: add cis(firmware) of 3Com multifunction pcmcia card
3c589_cs,3c574_cs,serial_cs:
(1)add cis(firmware) of 3Com lan&modem mulitifunction pcmcia card.
(2)load correct configuration register for 3Com card
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 1 May 2009 22:35:28 +0000 (15:35 -0700)]
bonding: correct the cleanup in bond_create()
This patch makes the cleanup in bond_create nicer :) Also now the forgotten
free_netdev is called.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grant Likely [Fri, 1 May 2009 22:34:02 +0000 (15:34 -0700)]
virtio: add missing include to virtio_net.h
virtio_net.h uses the macro ETH_ALEN which is defined in linux/if_ether.h.
Discovered when hacking on virtio-over-pci patches.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ayaz Abdulla [Fri, 1 May 2009 01:41:50 +0000 (01:41 +0000)]
forcedeth: add clock gating feature <resend>
This patch adds new logic to support a clock gating feature found on the
latest set of chipsets. The clock gating is performed on the tx/rx
engines when the link is disconnected. Clock gating helps in reducing
power consumption.
* modified based on comments from netdev
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steve Glendinning [Fri, 1 May 2009 06:07:22 +0000 (06:07 +0000)]
smsc95xx: add support for LAN9512 and LAN9514
LAN9512 and LAN9514 are USB hubs with an integrated 10/100 ethernet
controller. Logically this looks like an ethernet controller (similar
to LAN9500) permanently attached to one of the hub's downstream ports.
This patch adds the usb device id of the new ethernet controller to the
smsc95xx driver. This id is the same in both new devices.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steve Glendinning [Fri, 1 May 2009 05:46:51 +0000 (05:46 +0000)]
smsc95xx: configure LED outputs
SMSC LAN9500 has dual purpose GPIO/LED pins, and by default at power-on
these are configured as GPIOs. This means that if LEDs are fitted they
won't ever light.
This patch sets them to be LED outputs for speed, duplex and
link/activity.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruno Prémont [Wed, 29 Apr 2009 20:45:17 +0000 (20:45 +0000)]
netconsole: take care of NETDEV_UNREGISTER event
When netconsole is loaded and a network interface fades away (e.g. on
rmmod $interface_driver_module) the rmmod remains stuck and some locks
are taken that prevent any additional module loading/unloading as well
as interface up/down changes.
In addition kernel logs (and console) get flooded at 10s interval with
[ 122.464065] unregister_netdevice: waiting for eth0 to become free. Usage count = 1
[ 132.704059] unregister_netdevice: waiting for eth0 to become free. Usage count = 1
This patch lets netconsole take NETDEV_UNREGISTER event into account
and release the affected interface if it was in use.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Laszlo Attila Toth [Fri, 1 May 2009 22:23:10 +0000 (15:23 -0700)]
xt_socket: checks for the state of nf_conntrack
xt_socket can use connection tracking, and checks whether it is a module.
Signed-off-by: Laszlo Attila Toth <panther@balabit.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Kroah-Hartman [Thu, 30 Apr 2009 12:19:31 +0000 (12:19 +0000)]
net: remove driver_data direct access of struct device
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 23 Apr 2009 03:39:04 +0000 (03:39 +0000)]
bonding: bond_slave_info_query() fix
bond_slave_info_query() should keep a read lock while accessing slave info,
or risk accessing stale data and corruption.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergey Senozhatsky [Fri, 1 May 2009 16:15:09 +0000 (09:15 -0700)]
cxgb3: fixing gcc 4.4 compiler warning: suggest parentheses around operand of ‘!’
Trivial: fixing gcc 4.4 compiler warning:
drivers/net/cxgb3/t3_hw.c: In function ‘t3_prep_adapter’:
drivers/net/cxgb3/t3_hw.c:3782: warning: suggest parentheses around operand of ‘!’ or change ‘|’ to ‘||’ or ‘!’ to ‘~’
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@mail.by>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 May 2009 16:10:46 +0000 (09:10 -0700)]
netfilter: use likely() in xt_info_rdlock_bh()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 May 2009 16:05:06 +0000 (09:05 -0700)]
net: Fix skb_tx_hash() for forwarding workloads.
When skb_rx_queue_recorded() is true, we dont want to use jash distribution
as the device driver exactly told us which queue was selected at RX time.
jhash makes a statistical shuffle, but this wont work with 8 static inputs.
Later improvements would be to compute reciprocal value of real_num_tx_queues
to avoid a divide here. But this computation should be done once,
when real_num_tx_queues is set. This needs a separate patch, and a new
field in struct net_device.
Reported-by: Andrew Dickinson <andrew@whydna.net>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Thu, 30 Apr 2009 12:41:19 +0000 (05:41 -0700)]
net: Fix oops when splicing skbs from a frag_list.
Lennert Buytenhek wrote:
> Since
4fb669948116d928ae44262ab7743732c574630d ("net: Optimize memory
> usage when splicing from sockets.") I'm seeing this oops (e.g. in
> 2.6.30-rc3) when splicing from a TCP socket to /dev/null on a driver
> (mv643xx_eth) that uses LRO in the skb mode (lro_receive_skb) rather
> than the frag mode:
My patch incorrectly assumed skb->sk was always valid, but for
"frag_listed" skbs we can only use skb->sk of their parent.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Debugged-by: Lennert Buytenhek <buytenh@wantstofly.org>
Tested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 30 Apr 2009 03:30:35 +0000 (20:30 -0700)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6
Conflicts:
Documentation/isdn/00-INDEX
drivers/net/wireless/iwlwifi/iwl-scan.c
drivers/net/wireless/rndis_wlan.c
net/mac80211/main.c
David S. Miller [Thu, 30 Apr 2009 00:53:20 +0000 (17:53 -0700)]
Revert "vxge: use max() instead of VXGE_HW_SET_LEVEL"
This reverts commit
011983048a120e520147361be1067dd82343038e.
Causes warnings in the build as reported by Stephen Rothwell.
So this change is worse than what it's curing.
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:34:44 +0000 (08:34 +0000)]
mii: Rewrite mii_ethtool_gset() to report mdio_support and lp_advertising
Ignore link partner advertising flags while AN is not complete.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:25:57 +0000 (08:25 +0000)]
ethtool/mdio: Support backplane mode negotiation
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:21:53 +0000 (08:21 +0000)]
ethtool/mdio: Report MDIO mode support and link partner advertising
Add mdio_support and lp_advertising fields to ethtool_cmd. Set these
in mdio45_ethtool_gset{,_npage}().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:20:37 +0000 (08:20 +0000)]
sfc: Use generic MDIO flow control auto-negotiation functions
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:19:36 +0000 (08:19 +0000)]
mdio: Add mdio45_ethtool_spauseparam_an()
This implements the ETHTOOL_SPAUSEPARAM operation for MDIO (clause 45)
PHYs with auto-negotiation MMDs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:19:03 +0000 (08:19 +0000)]
mii: Add mii_advertise_flowctrl()
This converts flow control capabilites to an advertising mask and can
be useful in combination with mii_resolve_flowctrl_fdx().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:15:05 +0000 (08:15 +0000)]
mii: Simplify mii_resolve_flowctrl_fdx()
This is a shorter and more comprehensible formulation of the
conditions for each flow control mode.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:13:29 +0000 (08:13 +0000)]
s2io: Use generic MDIO definitions
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:11:05 +0000 (08:11 +0000)]
ixgb: Use generic MDIO definitions
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:08:58 +0000 (08:08 +0000)]
ixgbe: Use generic MDIO definitions and functions
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:07:20 +0000 (08:07 +0000)]
cxgb3: Use generic MDIO definitions and mdio_mii_ioctl()
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:06:34 +0000 (08:06 +0000)]
chelsio: Use generic MDIO definitions and mdio_mii_ioctl()
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:05:08 +0000 (08:05 +0000)]
sfc: Use generic MDIO functions and definitions
Make use of the newly-added generic MDIO clause 45 support and remove
redundant definitions.
Add an 'efx_' prefix to the remaining driver-specific MDIO functions
and remove arguments which are redundant with efx->mdio.prtad.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:04:46 +0000 (08:04 +0000)]
mdio: Add generic MDIO (clause 45) support functions
These roughly mirror many of the MII library functions and are based
on code from the sfc driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:04:14 +0000 (08:04 +0000)]
mdio: Add register definitions for MDIO (clause 45)
IEEE 802.3 clause 45 specifies the MDIO interface and registers for
use in 10G and other PHYs, similar to the MII management interface.
PHYs may have up to 32 MMDs corresponding to different sub-layers and
functions, each with up to 65536 registers. These are addressed by
PRTAD (similar to the MII PHY address) and DEVAD. Define a mapping
for specifying PRTAD and DEVAD through the existing MII ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 29 Apr 2009 08:02:59 +0000 (08:02 +0000)]
ethtool: Add port type PORT_OTHER
Add a PORT_OTHER to represent all other physical port types. Current
NICs generally do not allow switching between multiple port types in
software so specific types should not be needed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennert Buytenhek [Wed, 29 Apr 2009 11:58:18 +0000 (11:58 +0000)]
mv643xx_eth: 64bit mib counter read fix
On several mv643xx_eth hardware versions, the two 64bit mib counters
for 'good octets received' and 'good octets sent' are actually 32bit
counters, and reading from the upper half of the register has the same
effect as reading from the lower half of the register: an atomic
read-and-clear of the entire 32bit counter value. This can under heavy
traffic occasionally lead to small numbers being added to the upper
half of the 64bit mib counter even though no 32bit wrap has occured.
Since we poll the mib counters at least every 30 seconds anyway, we
might as well just skip the reads of the upper halves of the hardware
counters without breaking the stats, which this patch does.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennert Buytenhek [Wed, 29 Apr 2009 11:57:34 +0000 (11:57 +0000)]
mv643xx_eth: OOM handling fixes
Currently, when OOM occurs during rx ring refill, mv643xx_eth will get
into an infinite loop, due to the refill function setting the OOM bit
but not clearing the 'rx refill needed' bit for this queue, while the
calling function (the NAPI poll handler) will call the refill function
in a loop until the 'rx refill needed' bit goes off, without checking
the OOM bit.
This patch fixes this by checking the OOM bit in the NAPI poll handler
before attempting to do rx refill. This means that once OOM occurs,
we won't try to do any memory allocations again until the next invocation
of the poll handler.
While we're at it, change the OOM flag to be a single bit instead of
one bit per receive queue since OOM is a system state rather than a
per-queue state, and cancel the OOM timer on entry to the NAPI poll
handler if it's running to prevent it from firing when we've already
come out of OOM.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
John Dykstra [Thu, 30 Apr 2009 00:22:30 +0000 (17:22 -0700)]
pcnet32: Remove pointless memory barriers
These two memory barriers in performance-critical paths are not needed
on x86. Even if some other architecture does buffer PCI I/O space
writes, the existing memory-mapped I/O barriers are unlikely to be what
is needed.
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 29 Apr 2009 22:52:56 +0000 (15:52 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6
Johannes Berg [Tue, 28 Apr 2009 22:28:18 +0000 (00:28 +0200)]
mac80211: default to automatic power control
In "mac80211: correct wext transmit power handler"
I fixed the wext handler, but forgot to make the default of the
user_power_level -1 (aka "auto"), so that now the transmit power
is always set to 0, causing associations to time out and similar
problems since we're transmitting with very little power. Correct
this by correcting the default user_power_level to -1.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Bisected-by: Niel Lambrechts <niel.lambrechts@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alan Jenkins [Wed, 29 Apr 2009 10:41:24 +0000 (11:41 +0100)]
mac80211: fix modprobe deadlock by not calling wep_init under rtnl_lock
- ieee80211_wep_init(), which is called with rtnl_lock held, blocks in
request_module() [waiting for modprobe to load a crypto module].
- modprobe blocks in a call to flush_workqueue(), when it closes a TTY
[presumably when it exits].
- The workqueue item linkwatch_event() blocks on rtnl_lock.
There's no reason for wep_init() to be called with rtnl_lock held, so
just move it outside the critical section.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don Skidmore [Wed, 29 Apr 2009 07:22:31 +0000 (00:22 -0700)]
ixgbe: Use pci_wake_from_d3() instead of multiple pci_enable_wake()
We were calling pci_enable_wake() twice in a row for both D3_hot
and D3_cold. This replaces those calls with a call to pci_wake_from_d3()
to avoid issues with PCI PM vs ordering constraints.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Tue, 28 Apr 2009 15:29:11 +0000 (15:29 +0000)]
netxen: fix firmware download
o hold the firmware in memory across suspend, since filesystem
may not be up after resuming.
o reset the chip after requesting firmware, to minimize downtime
for NC-SI.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Tue, 28 Apr 2009 15:29:10 +0000 (15:29 +0000)]
netxen: refactor netxen_recv_context struct
o move related fields into netxen_recv_context struct.
o allocate rx buffer and descriptor rings dynamically.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Tue, 28 Apr 2009 15:29:09 +0000 (15:29 +0000)]
netxen: fix link event handling
Firmware starting 4.0.402 started supporting link events, disable
it for older firmwares.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thadeu Lima de Souza Cascardo [Wed, 29 Apr 2009 05:42:39 +0000 (22:42 -0700)]
e100: do not go D3 in shutdown unless system is powering off
After experimenting with kexec with the last merges after 2.6.29, I've
had some problems when probing e100. It would not read the eeprom. After
some bisects, I realized this has been like that since forever (at least
2.6.18). The problem is that shutdown is doing the same thing that
suspend does and puts the device in D3 state. I couldn't find a way to
get the device back to a sane state in the probe function. So, based on
some similar patches from Rafael J. Wysocki for e1000, e1000e, and ixgbe,
I wrote this one for e100.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 29 Apr 2009 05:40:49 +0000 (22:40 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/holtmann/bluetooth-2.6