OSDN Git Service
Manish Rangankar [Wed, 21 Nov 2018 09:25:20 +0000 (01:25 -0800)]
scsi: qedi: Add packet filter in light L2 Rx path.
Add packet filter to avoid unnecessary packet processing in iscsiuio.
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Manish Rangankar [Wed, 21 Nov 2018 09:25:19 +0000 (01:25 -0800)]
scsi: qedi: Check for session online before getting iSCSI TLV data.
The kernel panic was observed after switch side perturbation,
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<
ffffffff8132b5a0>] strcmp+0x20/0x40
PGD 0 Oops: 0000 [#1] SMP
CPU: 8 PID: 647 Comm: kworker/8:1 Tainted: G W OE ------------ 3.10.0-693.el7.x86_64 #1
Hardware name: HPE ProLiant DL380 Gen10/ProLiant DL380 Gen10, BIOS U30 06/20/2018
Workqueue: slowpath-13:00. qed_slowpath_task [qed]
task:
ffff880429eb8fd0 ti:
ffff880429190000 task.ti:
ffff880429190000
RIP: 0010:[<
ffffffff8132b5a0>] [<
ffffffff8132b5a0>] strcmp+0x20/0x40
RSP: 0018:
ffff880429193c68 EFLAGS:
00010202
RAX:
000000000000000a RBX:
0000000000000002 RCX:
0000000000000000
RDX:
0000000000000001 RSI:
0000000000000001 RDI:
ffff88042bda7a41
RBP:
ffff880429193c68 R08:
000000000000ffff R09:
000000000000ffff
R10:
0000000000000007 R11:
ffff88042b3af338 R12:
ffff880420b007a0
R13:
ffff88081aa56af8 R14:
0000000000000001 R15:
ffff88081aa50410
FS:
0000000000000000(0000) GS:
ffff88042fe00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000000000000 CR3:
00000000019f2000 CR4:
00000000003407e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Stack:
ffff880429193d20 ffffffffc02a0c90 ffffc90004b32000 ffff8803fd3ec600
ffff88042bda7800 ffff88042bda7a00 ffff88042bda7840 ffff88042bda7a40
0000000129193d10 2e3836312e323931 ff000a342e363232 ffffffffc01ad99d
Call Trace:
[<
ffffffffc02a0c90>] qedi_get_protocol_tlv_data+0x270/0x470 [qedi]
[<
ffffffffc01ad99d>] ? qed_mfw_process_tlv_req+0x24d/0xbf0 [qed]
[<
ffffffffc01653ae>] qed_mfw_fill_tlv_data+0x5e/0xd0 [qed]
[<
ffffffffc01ad9b9>] qed_mfw_process_tlv_req+0x269/0xbf0 [qed]
Fix kernel NULL pointer deref by checking for session is online before
getting iSCSI TLV data.
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nilesh Javali [Wed, 21 Nov 2018 09:25:18 +0000 (01:25 -0800)]
scsi: qedi: Allocate IRQs based on msix_cnt
The driver load on some systems failed with error,
[0004:01:00.5]:[qedi_request_msix_irq:2524]:8: request_irq failed.
Allocate the IRQs based on MSIX count obtained from qed module instead of
number of queues.
Signed-off-by: Nilesh Javali <nilesh.javali@cavium.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nilesh Javali [Wed, 21 Nov 2018 09:25:17 +0000 (01:25 -0800)]
scsi: qedi: Replace PAGE_SIZE with QEDI_PAGE_SIZE
Use QEDI_PAGE_SIZE for enablement of module on systems with 64K page size.
Signed-off-by: Nilesh Javali <nilesh.javali@cavium.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nilesh Javali [Wed, 21 Nov 2018 09:25:16 +0000 (01:25 -0800)]
scsi: qedi: Fix spelling mistake "OUSTANDING" -> "OUTSTANDING"
Fix trivial spelling mistake within macro definition.
Signed-off-by: Nilesh Javali <nilesh.javali@cavium.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nilesh Javali [Wed, 21 Nov 2018 09:25:15 +0000 (01:25 -0800)]
scsi: qedi: Cleanup redundant QEDI_PAGE_SIZE macro definition
Remove redundant macro definition.
Signed-off-by: Nilesh Javali <nilesh.javali@cavium.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
David Disseldorp [Fri, 23 Nov 2018 17:36:13 +0000 (18:36 +0100)]
scsi: target: replace fabric_ops.name with fabric_alias
iscsi_target_mod is the only LIO fabric where fabric_ops.name differs from
the fabric_ops.fabric_name string. fabric_ops.name is used when matching
target/$fabric ConfigFS create paths, so rename it .fabric_alias and
fallback to target/$fabric vs .fabric_name comparison if .fabric_alias
isn't initialised. iscsi_target_mod is the only fabric module to set
.fabric_alias . All other fabric modules rely on .fabric_name matching and
can drop the duplicate string.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
David Disseldorp [Fri, 23 Nov 2018 17:36:12 +0000 (18:36 +0100)]
scsi: target: drop unnecessary get_fabric_name() accessor from fabric_ops
All fabrics return a const string. In all cases *except* iSCSI the
get_fabric_name() string matches fabric_ops.name.
Both fabric_ops.get_fabric_name() and fabric_ops.name are user-facing, with
the former being used for PR/ALUA state and the latter for ConfigFS
(config/target/$name), so we unfortunately need to keep both strings around
for now. Replace the useless .get_fabric_name() accessor function with a
const string fabric_name member variable.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
David Disseldorp [Fri, 23 Nov 2018 17:36:11 +0000 (18:36 +0100)]
scsi: target: drop unused pi_prot_format attribute storage
On write, the pi_prot_format configfs attribute invokes the device
format_prot() callback if present. Read dumps the contents of
se_dev_attrib.pi_prot_format which is always zero. Make the configfs
attribute write-only, and drop the always zero se_dev_attrib.pi_prot_format
storage.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sabyasachi Gupta [Sun, 18 Nov 2018 14:38:48 +0000 (20:08 +0530)]
scsi: lpfc: Use dma_zalloc_coherent
Replaced dma_alloc_coherent + memset with dma_zalloc_coherent.
Signed-off-by: Sabyasachi Gupta <sabyasachi.linux@gmail.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
YueHaibing [Mon, 12 Nov 2018 01:54:05 +0000 (01:54 +0000)]
scsi: bnx2i: remove set but not used variable 'cid_num'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/bnx2i/bnx2i_hwi.c: In function 'bnx2i_process_ofld_cmpl':
drivers/scsi/bnx2i/bnx2i_hwi.c:2430:6: warning:
variable 'cid_num' set but not used [-Wunused-but-set-variable]
It never used since commit
cf4e6363859d ("[SCSI] bnx2i: Add bnx2i iSCSI driver.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Sat, 10 Nov 2018 08:28:22 +0000 (09:28 +0100)]
scsi: aha1542: convert to DMA mapping API
aha1542 is one of the last users of the legacy isa_*_to_bus APIs, which
also isn't portable enough. Convert it to the proper DMA mapping API.
Thanks to Ondrej Zary for testing and finding and fixing a crucial bug.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Fri, 9 Nov 2018 17:47:20 +0000 (09:47 -0800)]
scsi: megaraid_sas: Add support for MegaRAID Aero controllers
This patch adds support for MegaRAID Aero controller PCI IDs. Print a
message when a configurable secure type controller is encountered.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sreekanth Reddy [Fri, 9 Nov 2018 09:34:12 +0000 (15:04 +0530)]
scsi: mpt3sas: Display message on Configurable secure HBA
Display following warning message only upon detection of configurable
secure type controllers.
"HBA is in Configurable Secure mode"
[mkp: typos]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Yue Haibing [Thu, 8 Nov 2018 06:31:21 +0000 (06:31 +0000)]
scsi: libfc: Remove set but not used variable 'disc'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/libfc/fc_rport.c: In function 'fc_rport_recv_flogi_req':
drivers/scsi/libfc/fc_rport.c:866:18: warning:
variable 'disc' set but not used [-Wunused-but-set-variable]
It no used any more after
commit
baa6719f902a ("libfc: Update rport reference counting")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
David Disseldorp [Wed, 7 Nov 2018 13:11:07 +0000 (14:11 +0100)]
scsi: target: add emulate_pr backstore attr to toggle PR support
The new emulate_pr backstore attribute allows for Persistent Reservation
and SCSI2 RESERVE/RELEASE support to be completely disabled. This can be
useful for scenarios such as:
- Ensuring ATS (Compare & Write) usage on recent VMware ESXi initiators.
- Allowing clustered (e.g. tcm-user) backends to block such requests,
avoiding the multi-node reservation state propagation.
When explicitly disabled, PR and RESERVE/RELEASE requests receive Invalid
Command Operation Code response sense data.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Fri, 2 Nov 2018 15:35:23 +0000 (16:35 +0100)]
scsi: cxgb4i: fix thermal configuration dependencies
I fixed a bug by adding a dependency in the network driver, but that fix
caused a related bug in the SCSI driver:
WARNING: unmet direct dependencies detected for CHELSIO_T4
Depends on [m]: NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_CHELSIO [=y] && PCI [=y] && (IPV6 [=y] || IPV6 [=y]=n) && (THERMAL [=m] || !THERMAL [=m])
Selected by [y]:
- SCSI_CXGB4_ISCSI [=y] && SCSI_LOWLEVEL [=y] && SCSI [=y] && PCI [=y] && INET [=y] && (IPV6 [=y] || IPV6 [=y]=n)
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_init':
cxgb4_thermal.c:(.text+0x158): undefined reference to `thermal_zone_device_register'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_remove':
cxgb4_thermal.c:(.text+0x1d8): undefined reference to `thermal_zone_device_unregister'
/git/arm-soc/Makefile:1042: recipe for target 'vmlinux' failed
The same dependency needs to be propagated here to make it work correctly
with CONFIG_THERMAL=m and SCSI_CXGB4_ISCSI=y. That change by itself causes
another problem with a circular dependency, as we use 'select NETDEVICES'.
This is something we really should not do anyway, as a driver symbol should
never select another major subsystem, so let's turn that into a 'depends
on'. I don't see any downsides of that, as NETDEVICES is only disabled in
rather obscure cases that are not relevant to the users of cxgb4i.
Fixes:
e70a57fa59bb ("cxgb4: fix thermal configuration dependencies")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Souptick Joarder [Thu, 1 Nov 2018 04:19:09 +0000 (09:49 +0530)]
scsi: aic94xx: Use dma_pool_zalloc
Replaced dma_pool_alloc + memset with dma_pool_zalloc.
Signed-off-by: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:58 +0000 (15:44 +0100)]
scsi: zfcp: drop old default switch case which might paper over missing case
This was introduced with v2.6.27 commit
287ac01acf22 ("[SCSI] zfcp: Cleanup
code in zfcp_erp.c") but would now suppress helpful -Wswitch compiler
warnings when building with W=1 such as the following forced example:
drivers/s390/scsi/zfcp_erp.c: In function 'zfcp_erp_setup_act':
drivers/s390/scsi/zfcp_erp.c:220:2: warning: enumeration value 'ZFCP_ERP_ACTION_REOPEN_PORT' not handled in switch [-Wswitch]
switch (need) {
^~~~~~
But then again, only with W=1 we would notice unhandled enum cases.
Without the default cases and a missed unhandled enum case, the code might
perform unforeseen things we might not want...
As of today, we never run through the removed default case, so removing it
is no functional change. In the future, we never should run through a
default case but introduce the necessary specific case(s) to handle new
functionality.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:57 +0000 (15:44 +0100)]
scsi: zfcp: drop default switch case which might paper over missing case
This was introduced with v4.18 commit
8c3d20aada70 ("scsi: zfcp: fix
missing REC trigger trace for all objects in ERP_FAILED") but would now
suppress helpful -Wswitch compiler warnings when building with W=1 such as
the following forced example:
drivers/s390/scsi/zfcp_erp.c: In function 'zfcp_erp_handle_failed':
drivers/s390/scsi/zfcp_erp.c:126:2: warning: enumeration value 'ZFCP_ERP_ACTION_REOPEN_PORT_FORCED' not handled in switch [-Wswitch]
switch (want) {
^~~~~~
But then again, only with W=1 we would notice unhandled enum cases.
Without the default cases and a missed unhandled enum case, the code might
perform unforeseen things we might not want...
As of today, we never run through the removed default case, so removing it
is no functional change. In the future, we never should run through a
default case but introduce the necessary specific case(s) to handle new
functionality.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:56 +0000 (15:44 +0100)]
scsi: zfcp: silence -Wimplicit-fallthrough in zfcp_erp_lun_strategy()
For some reason the already existing substring "fall through" in the
comment is not sufficient for GCC to silence -Wimplicit-fallthrough.
CC [M] drivers/s390/scsi/zfcp_erp.o
drivers/s390/scsi/zfcp_erp.c: In function 'zfcp_erp_lun_strategy':
drivers/s390/scsi/zfcp_erp.c:1065:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (atomic_read(&zfcp_sdev->status) & ZFCP_STATUS_COMMON_OPEN)
^
drivers/s390/scsi/zfcp_erp.c:1068:2: note: here
case ZFCP_ERP_STEP_LUN_CLOSING:
^~~~
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:55 +0000 (15:44 +0100)]
scsi: zfcp: silence remaining kdoc warnings in header files
Improve whatever the following simple invocation reported:
$ ./scripts/kernel-doc -none drivers/s390/scsi/*.h
While at it, improve some related kdoc,
including struct zfcp_fsf_ct_els in zfcp_fsf.h.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:54 +0000 (15:44 +0100)]
scsi: zfcp: silence all W=1 build warnings for existing kdoc
While at it also improve some copy & paste kdoc mistakes.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:53 +0000 (15:44 +0100)]
scsi: zfcp: properly format LUN (and WWPN) for LUN sharing violation kmsg
zfcp: <devbusid>: LUN 0x0 on port 0x5005076......... ...
zfcp: <devbusid>: LUN 0x1000000000000 on port 0x5005076......... ...
should be
zfcp: <devbusid>: LUN 0x0000000000000000 on port 0x5005076......... ...
zfcp: <devbusid>: LUN 0x0001000000000000 on port 0x5005076.........
is already in use by CSS., MIF Image ID .
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:52 +0000 (15:44 +0100)]
scsi: zfcp: use enum zfcp_erp_act_result for argument/return of affected functions
With that instead of just "int" it becomes clear which functions return
this type and which ones also accept it as argument they just pass through
in some cases or modify in other cases. v2.6.27 commit
287ac01acf22
("[SCSI] zfcp: Cleanup code in zfcp_erp.c") introduced the enum which was
cpp defines previously.
Silence some false -Wswitch compiler warning cases with individual
NOP cases. When adding more enum values and building with W=1 we
would get compiler warnings about missed new cases.
Consistently use the variable name "result", so change "retval" in
zfcp_erp_strategy() to "result". This avoids confusion with other compile
unit variables "retval" having different semantics and type.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:51 +0000 (15:44 +0100)]
scsi: zfcp: use enum zfcp_erp_steps for struct zfcp_erp_action.step
Use the already defined enum for this purpose to get at least some build
checking (even though an enum is type equivalent to an int in C). v2.6.27
commit
287ac01acf22 ("[SCSI] zfcp: Cleanup code in zfcp_erp.c") introduced
the enum which was cpp defines previously.
Since struct zfcp_erp_action type is embedded into other structures living
in zfcp_def.h, we have to move enum zfcp_erp_act_type from its private
definition in zfcp_erp.c to the zfcp-global zfcp_def.h
Silence some false -Wswitch compiler warning cases with individual NOP
cases. When adding more enum values and building with W=1 we would get
compiler warnings about missed new cases.
Add missing break statements in some of the above switch cases. No
functional change, but making it future-proof. I think all of these should
have had a break statement ever since, even if these switch cases happened
to be the last ones in the switch statement body.
"Fall through" in the context of switch case usually means not to have a
break and fall through to the subsequent switch case. However, I think this
old comment meant that here we do not have an _early return_ in the switch
case but the code path continues after the switch case body.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:50 +0000 (15:44 +0100)]
scsi: zfcp: the action field of zfcp_erp_action is actually the type
&zfcp_erp_action.action ==> &zfcp_erp_action.type
While at it, make use of the already defined enum for this purpose to get
at least some build checking (even though an enum is type equivalent to an
int in C). v2.6.27 commit
287ac01acf22 ("[SCSI] zfcp: Cleanup code in
zfcp_erp.c") introduced the enum which was cpp defines previously.
To prevent compiler warnings with the switch(act->type), we have to
separate the recently added eyecatchers from enum zfcp_erp_act_type.
Since struct zfcp_erp_action type is embedded into other structures living
in zfcp_def.h, we have to move enum zfcp_erp_act_type from its private
definition in zfcp_erp.c to the zfcp-global zfcp_def.h.
Silence one false -Wswitch compiler warning case: LUNs as the leaves in our
object tree do not have any follow-up success recovery.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:49 +0000 (15:44 +0100)]
scsi: zfcp: clarify function argument name for trace tag string
v2.6.30 commit
5ffd51a5e495 ("[SCSI] zfcp: replace current ERP logging with
a more convenient version") changed trace record distinguishing from a
numerical ID to a 7 character string called "trace tag". While starting to
use function arguments with different type and semantics, it did not change
the argument name accordingly.
v2.6.38 commit
ae0904f60fab ("[SCSI] zfcp: Redesign of the debug tracing
for recovery actions.") renamed variable names "id" into "tag" but only
within zfcp_dbf.*, not within zfcp_erp.c.
This was a bit confusing since the remainder of zfcp does use the term
"trace tag". Also "id" is quite generic and it's not obvious for what.
Just unify it consistently and use the "dbf" prefix to relate the arguments
to the code in zfcp_dbf.*.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:48 +0000 (15:44 +0100)]
scsi: zfcp: ERP thread setup kdoc update
zfcp_erp_thread_setup() update complements v2.6.32 commit
347c6a965dc1
("[SCSI] zfcp: Use kthread API for zfcp erp thread").
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:47 +0000 (15:44 +0100)]
scsi: zfcp: update kernel message for invalid FCP_CMND length, it's not the CDB
The CDB is just a part inside of FCP_CMND, see zfcp_fc_scsi_to_fcp().
While at it, fix the device driver reaction: adapter not LUN shutdown.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:46 +0000 (15:44 +0100)]
scsi: zfcp: drop duplicate seq_no from zfcp_fsf_req which is also in QTCB header
There is no point for double bookkeeping especially just for tracing. The
trace can take it from the QTCB which always exists for non-SRB responses
traced with zfcp_dbf_hba_fsf_res().
As a side effect, this removes an alignment hole and reduces the size of
struct zfcp_fsf_req, and thus of each pending request, by 8 bytes.
Before:
$ pahole -C zfcp_fsf_req drivers/s390/scsi/zfcp.ko
...
struct fsf_qtcb * qtcb; /* 144 8 */
u32 seq_no; /* 152 4 */
/* XXX 4 bytes hole, try to pack */
void * data; /* 160 8 */
...
/* size: 296, cachelines: 2, members: 14 */
/* sum members: 288, holes: 2, sum holes: 8 */
/* last cacheline: 40 bytes */
After:
$ pahole -C zfcp_fsf_req drivers/s390/scsi/zfcp.ko
...
struct fsf_qtcb * qtcb; /* 144 8 */
void * data; /* 152 8 */
...
/* size: 288, cachelines: 2, members: 13 */
/* sum members: 284, holes: 1, sum holes: 4 */
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:45 +0000 (15:44 +0100)]
scsi: zfcp: drop duplicate fsf_command from zfcp_fsf_req which is also in QTCB header
Status read buffers (SRBs, unsolicited notifications) never use a QTCB
[zfcp_fsf_req_create()]. zfcp_fsf_req_send() already uses this to
distinguish SRBs from other FSF request types. We can re-use this method in
zfcp_fsf_req_complete(). Introduce a helper function to make the check for
req->qtcb less magic.
SRBs always are FSF_QTCB_UNSOLICITED_STATUS, so we can hard-code this for
the two trace functions dealing with SRBs.
All other FSF request types have a QTCB and we can get the fsf_command from
there.
zfcp_dbf_hba_fsf_response() and thus zfcp_dbf_hba_fsf_res() are only called
for non-SRB requests so it's safe to dereference the QTCB
[zfcp_fsf_req_complete() returns early on SRB, else calls
zfcp_fsf_protstatus_eval() which calls zfcp_dbf_hba_fsf_response()]. In
zfcp_scsi_forget_cmnd() we guard the QTCB dereference with a preceding NULL
check and rely on boolean shortcut evaluation.
As a side effect, this causes an alignment hole which we can close in
a later patch after having cleaned up all fields of struct zfcp_fsf_req.
Before:
$ pahole -C zfcp_fsf_req drivers/s390/scsi/zfcp.ko
...
u32 status; /* 136 4 */
u32 fsf_command; /* 140 4 */
struct fsf_qtcb * qtcb; /* 144 8 */
...
After:
$ pahole -C zfcp_fsf_req drivers/s390/scsi/zfcp.ko
...
u32 status; /* 136 4 */
/* XXX 4 bytes hole, try to pack */
struct fsf_qtcb * qtcb; /* 144 8 */
...
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:44 +0000 (15:44 +0100)]
scsi: zfcp: drop unnecessary forward prototype for struct zfcp_fsf_req
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:43 +0000 (15:44 +0100)]
scsi: zfcp: group sort internal structure definitions for proximity
Have structures just before the structures that use them (without
disrupting sequences of using structures such as zfcp_unit and
zfcp_scsi_dev):
- zfcp_adapter_mempool embedded in zfcp_adapter,
- zfcp_latenc... embedded in zfcp_scsi_dev.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:42 +0000 (15:44 +0100)]
scsi: zfcp: namespace prefix for internal latency data structures
In contrast to struct fsf_qual_latency_info, the ones here are not FSF but
software defined zfcp-internal.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:41 +0000 (15:44 +0100)]
scsi: zfcp: update width in comment for ZFCP_COMMON_FLAGS mask
v2.6.10 history commit
4062e12b2ba2 ("[PATCH] s390: zfcp act enhancements")
extended this mask by one nibble with the introduction of
ZFCP_STATUS_COMMON_ACCESS_DENIED == 0x00800000 for ACT (access control
table).
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:40 +0000 (15:44 +0100)]
scsi: zfcp: move scsi_eh & non-ERP timeout defines owned by and local to zfcp_fsf.c
Also clarify namespace prefix for the timeout used for FSF requests on
behalf of SCSI error recovery: It is zfcp_fsf_ not zfcp_scsi_.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:39 +0000 (15:44 +0100)]
scsi: zfcp: drop unnecessary forward prototype for struct zfcp_reqlist
While struct zfcp_adapter contains a pointer to zfcp_reqlist, the pointer
field does not need to know the structure or even a prototype.
The prototype was introduced with v2.6.34 commit
b6bd2fb92a7b ("[SCSI]
zfcp: Move FSF request tracking code to new file").
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Thu, 8 Nov 2018 14:44:38 +0000 (15:44 +0100)]
scsi: zfcp: move SG table helper from aux to fc and make them static
Since commit
663e0890e31c ("[SCSI] zfcp: remove access control tables
interface") these helper functions are only used for auto port scan in
zfcp_fc.c. Also change them to the corresponding namespace prefix.
This is a small cleanup for the miscellaneous catchall compile unit
zfcp_aux.c.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
zhong jiang [Thu, 8 Nov 2018 14:44:37 +0000 (15:44 +0100)]
scsi: zfcp: remove unnecessary null pointer check before mempool_destroy
mempool_destroy has taken null pointer check into account. so remove the
redundant check.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Benjamin Block <bblock@linux.ibm.com>
[maier@linux.ibm.com: depends on v4.3
4e3ca3e033d1 ("mm/mempool: allow NULL `pool' pointer in mempool_destroy()")]
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Thu, 15 Nov 2018 10:20:32 +0000 (18:20 +0800)]
scsi: libsas: Remove pcidev reference
Not all host drivers are PCI drivers - like hisi_sas, which supports a
platform driver - so remove reference to "pcidev".
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Thu, 15 Nov 2018 10:20:31 +0000 (18:20 +0800)]
scsi: libsas: Drop SAS_DPRINTK() and revise logs levels
Like sas_printk() did previously, SAS_DPRINTK() offers little value now
that libsas logs already have the "sas" prefix through pr_fmt(fmt). So it
can be dropped.
However, after reviewing some logs in libsas, it is noticed that debug
level is too low in many instances.
So this change drops SAS_DPRINTK() and revises some logs to a more
appropriate level. However many stay at debug level, although some
are significantly promoted.
We add -DDEBUG for compilation so that we keep the debug messages by
default, as before.
All the pre-existing checkpatch errors for spanning messages across
multiple lines are also fixed.
Finally, all other references to printk() [apart from special formatting
in sas_ata.c] are removed and replaced with appropriate pr_xxx().
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Thu, 15 Nov 2018 10:20:30 +0000 (18:20 +0800)]
scsi: libsas: Drop sas_printk()
The printk wrapper sas_printk() adds little value now that libsas logs
already have the "sas" prefix through pr_fmt(fmt), so just use pr_notice()
directly.
In addition, strings which span multiple lines are reunited.
Originally-from: Joe Perches <joe@perches.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Thu, 15 Nov 2018 10:20:29 +0000 (18:20 +0800)]
scsi: libsas: Use pr_fmt(fmt)
In preparation for dropping the libsas printk wrappers, use pr_fmt(fmt)
declaration to add the framework log prefix - "sas".
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Thu, 15 Nov 2018 10:20:28 +0000 (18:20 +0800)]
scsi: libsas: Delete sas_dump.{c, h}
The code in these files is not longer referenced, so delete them.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 9 Nov 2018 14:06:36 +0000 (22:06 +0800)]
scsi: hisi_sas: change the time of SAS SSP connection
Currently the time of SAS SSP connection is 1ms, which means the link
connection will fail if no IO response after this period.
For some disks handling large IO (such as 512k), 1ms is not enough, so
change it to 5ms.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 9 Nov 2018 14:06:35 +0000 (22:06 +0800)]
scsi: hisi_sas: Relocate some codes to avoid an unused check
In function hisi_sas_task_prep(), we check asd_sas_port, but in function
hisi_sas_task_exec(), we already refer to asd_sas_port by using function
dev_to_hisi_hba() implicitly. So to avoid this possible invalid
dereference, relocate the check to function hisi_sas_task_prep().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 9 Nov 2018 14:06:34 +0000 (22:06 +0800)]
scsi: hisi_sas: Add support for interrupt coalescing for v3 hw
If INT_COAL_EN is enabled, configure time and count of interrupt
coalescing. Then if CQ collects count of CQ entries in time, it will
report the interrupt. Or if CQ doesn't collect enough CQ entries in time,
it will report the interrupt at timeout.
As all the registers are not supported to be changed dynamically, we need
to config those register between disable and enable PHYs.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 9 Nov 2018 14:06:33 +0000 (22:06 +0800)]
scsi: hisi_sas: Add support for interrupt converge for v3 hw
If CQ_INT_CONVERGE_EN is enabled, the interrupts of all the 16 CQ queues
will be reported by CQ0.
So we need to change the process of CQ tasklet for this situation.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 9 Nov 2018 14:06:32 +0000 (22:06 +0800)]
scsi: hisi_sas: Create separate host attributes per HBA
Currently all the three HBA (v1/v2/v3 HW) share the same host attributes.
To support each HBA having separate attributes in future, create per-HBA
attributes.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Fri, 9 Nov 2018 15:54:06 +0000 (16:54 +0100)]
scsi: wd719x: always use generic DMA API
The wd719x driver currently uses a mix of the legacy PCI DMA and the
generic DMA APIs. Switch it over to the generic DMA API entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Fri, 9 Nov 2018 15:54:05 +0000 (16:54 +0100)]
scsi: wd719x: use per-command private data
Add the SCB onto the scsi command allocation and use dma streaming mappings
for it only when in use. This avoid possibly calling dma_alloc_coherent
under a lock or even in irq context, while also making the code simpler.
Thanks to Ondrej Zary for testing and various bug fixes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Fri, 9 Nov 2018 15:54:04 +0000 (16:54 +0100)]
scsi: wd719x: there should be no active SCBs on removal
Warn on that case instead of trying to free them which would be fatal in
case we actually had active ones.
[mkp: typos]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:10:24 +0000 (15:10 +0200)]
scsi: sym53c8xx: use dma_set_mask
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:10:23 +0000 (15:10 +0200)]
scsi: stex: use dma_set_mask_and_coherent
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API. Switch it over to the better generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:10:22 +0000 (15:10 +0200)]
scsi: mvumi: use dma_set_mask
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:10:21 +0000 (15:10 +0200)]
scsi: lpfc: use dma_set_mask_and_coherent
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API. Switch it over to the better generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:10:20 +0000 (15:10 +0200)]
scsi: isci: use dma_set_mask_and_coherent
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API. Switch it over to the better generic DMA API.
[mkp: s/iscsi/isci/]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:10:19 +0000 (15:10 +0200)]
scsi: initio: use dma_set_mask
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:10:18 +0000 (15:10 +0200)]
scsi: hptiop: use dma_set_mask
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:10:17 +0000 (15:10 +0200)]
scsi: hisi_sas: use dma_set_mask_and_coherent
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API. Switch it over to the better generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:10:16 +0000 (15:10 +0200)]
scsi: esas2r: use dma_set_mask_and_coherent
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API. Also move the dma_get_required_mask check before actually
setting the dma mask so that we don't end up with inconsistent settings in
corner cases.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:10:15 +0000 (15:10 +0200)]
scsi: dpt_i2o: use dma_set_mask
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API. Also move the dma_get_required_mask check before actually
setting the dma mask, so that we don't end up with inconsistent settings in
corner cases.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:10:14 +0000 (15:10 +0200)]
scsi: bfa: use dma_set_mask_and_coherent
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API. Switch it over to the better generic DMA API helper and
also ensure we set the coherent mask as well in the resume path.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:10:13 +0000 (15:10 +0200)]
scsi: arcmsr: use dma_set_mask
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Janek Kotas [Thu, 20 Sep 2018 13:08:30 +0000 (13:08 +0000)]
scsi: ufs: Add UFS platform driver for Cadence UFS
This patch adds a device tree platform driver for Cadence UFS Host
Controller. It can be enabled with SCSI_UFS_CDNS_PLATFORM Kconfig option.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Janek Kotas [Thu, 20 Sep 2018 13:08:22 +0000 (13:08 +0000)]
scsi: dt-bindings: ufs: Add bindings for Cadence UFS
This patch adds a DT binding documentation for Cadence UFS Host Controller.
Signed-off-by: Jan Kotas <jank@cadence.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Subhash Jadavani [Tue, 16 Oct 2018 08:59:41 +0000 (14:29 +0530)]
scsi: ufs: set the device reference clock setting
UFS host supplies the reference clock to UFS device and UFS device
specification allows host to provide one of the 4 frequencies (19.2 MHz, 26
MHz, 38.4 MHz, 52 MHz) for reference clock. Host should set the device
reference clock frequency setting in the device based on what frequency it
is supplying to UFS device.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:05:37 +0000 (15:05 +0200)]
scsi: pmcraid: use generic DMA API
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:05:36 +0000 (15:05 +0200)]
scsi: pmcraid: don't allocate a dma coherent buffer for sense data
We can just dma map the sense buffer passed with the scsi command,
and that gets us out of the nasty business of doing dma coherent
allocations from irq context.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:05:35 +0000 (15:05 +0200)]
scsi: pmcraid: simplify pmcraid_cancel_all a bit
No need for a local cmd_done variable, and pass boolean values as bool
type instead of u32.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:03:37 +0000 (15:03 +0200)]
scsi: qla2xxx: use lower_32_bits and upper_32_bits instead of reinventing them
This also moves the optimization for builds with 32-bit dma_addr_t to
the compiler (where it belongs) instead of opencoding it based on
incorrect assumptions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:03:36 +0000 (15:03 +0200)]
scsi: qla1280: properly handle 64-bit DMA
CONFIG_HIGHMEM is not in fact an indicator for > 32-bit dma addressing
Given that the driver is a bit weird and wants a compile time selection
switch to checking CONFIG_ARCH_DMA_ADDR_T_64BIT instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:03:35 +0000 (15:03 +0200)]
scsi: qla1280: use lower_32_bits and upper_32_bits instead of reinventing them
This also moves the optimization for builds with 32-bit dma_addr_t to
the compiler (where it belongs) instead of opencoding it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:03:34 +0000 (15:03 +0200)]
scsi: ips: properly handle 64-bit DMA
CONFIG_HIGHMEM64 is only one (and these days unusual) way to indicate
that > 32-bit dma address are possible. Replace it with a check of the
dma_addr_t size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Thu, 18 Oct 2018 13:03:33 +0000 (15:03 +0200)]
scsi: ips: use lower_32_bits and upper_32_bits instead of reinventing them
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chengguang Xu [Sun, 4 Nov 2018 13:57:50 +0000 (21:57 +0800)]
scsi: qla4xxx: remvoe unnecessary condition check for mempool_destroy()
mempool_destroy() can handle NULL pointer correctly, so there is no
need to check NULL pointer before calling mempool_destroy().
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chengguang Xu [Sun, 4 Nov 2018 13:57:49 +0000 (21:57 +0800)]
scsi: qla4xxx: remove unnecessary condition check for dma_pool_destroy()
dma_pool_destroy() can handle NULL pointer correctly, so there is no
need to check NULL pointer before calling dma_pool_destroy().
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 23 Oct 2018 20:41:12 +0000 (13:41 -0700)]
scsi: lpfc: update driver version to 12.0.0.8
Update the driver version to 12.0.0.8
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 23 Oct 2018 20:41:11 +0000 (13:41 -0700)]
scsi: lpfc: add Trunking support
Add trunking support to the driver. Trunking is found on more recent
asics. In general, trunking appears as a single "port" to the driver
and overall behavior doesn't differ. Link speed is reported as an
aggregate value, while link speed control is done on a per-physical
link basis with all links in the trunk symmetrical. Some commands
returning port information are updated to additionally provide
trunking information. And new ACQEs are generated to report physical
link events relative to the trunk.
This patch contains the following modifications:
- Added link speed settings of 128GB and 256GB.
- Added handling of trunk-related ACQEs, mainly logging and trapping
of physical link statuses.
- Added additional bsg interface to query trunk state by applications.
- Augment link_state sysfs attribtute to display trunk link status
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 23 Oct 2018 20:41:10 +0000 (13:41 -0700)]
scsi: lpfc: Implement GID_PT on Nameserver query to support faster failover
The switches seem to respond faster to GID_PT vs GID_FT NameServer
queries. Add support for GID_PT to be used over GID_FT to enable
faster storage failover detection. Includes addition of new module
parameter to select between GID_PT and GID_FT (GID_FT is default).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 23 Oct 2018 20:41:09 +0000 (13:41 -0700)]
scsi: lpfc: Correct loss of fc4 type on remote port address change
An address change for a remote port cause PRLI for the wrong protocol
to be sent. The node copy done in the discovery code skipped copying
the fc4 protocols supported as well.
Fix the copy logic for the address change. Beefed up log messages in
this area as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 23 Oct 2018 20:41:08 +0000 (13:41 -0700)]
scsi: lpfc: Fix odd recovery in duplicate FLOGIs in point-to-point
Testing a point-to-point topology and a case of re-FLOGI without
intervening link bouncing, showed an odd interaction with firmware and
a resulting scenario where the driver no longer probed after accepting
the new FLOGI.
Work around the firmware issue by issuing a link bounce if a FLOGI is
received after the link is already up and FLOGI's accepted.
While debugging the issue, realized that some debug traces should be
clarified to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 23 Oct 2018 20:41:07 +0000 (13:41 -0700)]
scsi: lpfc: Correct LCB RJT handling
When LCB's are rejected, if beaconing was already in progress, the
Reason Code Explanation was not being set. Should have been set to
command in progress.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 23 Oct 2018 20:41:06 +0000 (13:41 -0700)]
scsi: lpfc: fcoe: Fix link down issue after 1000+ link bounces
On FCoE adapters, when running link bounce test in a loop, initiator
failed to login with switch switch and required driver reload to
recover. Switch reached a point where all subsequent FLOGIs would be
LS_RJT'd. Further testing showed the condition to be related to not
performing FCF discovery between FLOGI's.
Fix by monitoring FLOGI failures and once a repeated error is seen
repeat FCF discovery.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 23 Oct 2018 20:41:05 +0000 (13:41 -0700)]
scsi: lpfc: Correct errors accessing fw log
This patch corrects two issues:
- An oops would occur if reading based on a non-zero offset. Offset
calculation was incorrect.
- Updates to ras config (logging level) were ignored if change was
made while fw logging was enabled. Revise to dynamically update.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 23 Oct 2018 20:41:04 +0000 (13:41 -0700)]
scsi: lpfc: Reset link or adapter instead of doing infinite nameserver PLOGI retry
Currently, PLOGI failures are infinitely delayed/retried. There have
been some fabric situations where the PLOGI's were to the nameserver
and it stopped responding. The retries would never clear up. A better
resolution in this situation is to retry a couple of times, then drop
the link and reinit. This brings back connectivity to the nameserver.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 23 Oct 2018 20:41:03 +0000 (13:41 -0700)]
scsi: lpfc: Fix LOGO/PLOGI handling when triggerd by ABTS Timeout event
After a LOGO in response to an ABTS timeout, a PLOGI wasn't issued to
re-establish the login. An nlp_type check in the LOGO completion
handler failed to restart discovery for NVME targets. Revised the
nlp_type check for NVME as well as SCSI.
While reviewing the LOGO handling a few other issues were seen and
were addressed:
- Better lock synchronization around ndlp data types
- When the ABTS times out, unregister the RPI before sending the LOGO
so that all local exchange contexts are cleared and nothing received
while awaiting LOGO/PLOGI handling will be accepted.
- LOGO handling optimized to:
Wait only R_A_TOV for a response.
It doesn't need to be retried on timeout. If there wasn't a
response, a PLOGI will be sent, thus an implicit logout
applies as well when the other port sees it.
If there is a response, any kind of response is considered "good"
and the XRI quarantined for a exchange qualifier window.
- PLOGI is issued as soon a LOGO state is resolved.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 23 Oct 2018 20:41:02 +0000 (13:41 -0700)]
scsi: lpfc: Fix lpfc_sli4_read_config return value check
An error is an error - but not to the existing return value check.
Revise check to handle any failure, not just EIO.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 23 Oct 2018 20:41:01 +0000 (13:41 -0700)]
scsi: lpfc: Correct speeds on SFP swap
Supported speeds is not updated when SFP is removed or replaced
Supported speed is obtained from lmt field in READ_CONFIG mailbox
response. Driver updates supported speeds only once from PCI probe
path. After that it is never updated. So, supported speeds remains the
same till reboot or driver reload.
When SFP is removed or inserted, driver gets SLI-Port Event ACQE. If
SFP is removed, lmt wil have value 0. If a different SFP is inserted,
lmt will have value according to its supported speeds. So, afterr
SLI-Port Event ACQE handling path, send READ_CONFIG mailbox and update
supported speeds. If READ_CONFIG fails, set supported speeds to
unknown and log.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 17 Oct 2018 06:37:57 +0000 (23:37 -0700)]
scsi: megaraid_sas: Update driver version
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 17 Oct 2018 06:37:56 +0000 (23:37 -0700)]
scsi: megaraid_sas: modify max supported lds related print
The print related to number of VDs that a particular firmware supports is
misleading in some cases. Even though supportMaxExtLDs is set, certain
firmware profiles only supports upto 64VDs.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 17 Oct 2018 06:37:55 +0000 (23:37 -0700)]
scsi: megaraid_sas: remove unused macro
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 17 Oct 2018 06:37:54 +0000 (23:37 -0700)]
scsi: megaraid_sas: increase timeout for IOC INIT to 180seconds
IOC INIT frame needs to be fired with a timeout of 180 seconds.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 17 Oct 2018 06:37:53 +0000 (23:37 -0700)]
scsi: megaraid_sas: Remove double endian conversion
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 17 Oct 2018 06:37:52 +0000 (23:37 -0700)]
scsi: megaraid_sas: Re-use max_mfi_cmds to calculate queue sizes
In megasas_init_adapter_fusion(), max_mfi_cmds is being calcuated as
(MEGASAS_FUSION_INTERNAL_CMDS + MEGASAS_FUSION_IOCTL_CMDS). max_mfi_cmds
can be used in megasas_configure_queue_sizes.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 17 Oct 2018 06:37:51 +0000 (23:37 -0700)]
scsi: megaraid_sas: Rename scratch_pad registers
Rename the scratch pad registers to match firmware headers. No functional
change.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 17 Oct 2018 06:37:50 +0000 (23:37 -0700)]
scsi: megaraid_sas: Remove spin lock for dpc operation
Optimization: No need to hold hba_lock in dpc context for reading atomic
variable.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 17 Oct 2018 06:37:49 +0000 (23:37 -0700)]
scsi: megaraid_sas: optimize raid context access in IO path
No functional change. Use local variables when accessing raid context in
IO path. Improves code readability.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 17 Oct 2018 06:37:48 +0000 (23:37 -0700)]
scsi: megaraid_sas: Fail init if heartbeat timer fails
When driver fails to start the heartbeat timer, exit from FW init.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>