OSDN Git Service
Viresh Kumar [Mon, 22 Jun 2015 11:12:26 +0000 (16:42 +0530)]
greybus: Add control protocol support
Add control protocol driver that is responsible for handling operations
on control CPort. The AP also needs to support incoming requests on its
control port. Features not implemented yet are marked as TODO for now.
NOTE: This also fixes cport-bundle-id to 0 and cport-id to 2 for control
protocol.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Viresh Kumar [Mon, 22 Jun 2015 11:06:47 +0000 (16:36 +0530)]
greybus: manifest: Allow bundles/connections list to be non-empty at manifest parsing
A connection and a bundle will be created for interfaces at the very
beginning for control protocol's functioning. And so the list of bundles
and connections for a interface will be non-empty by the time manifest
is parsed.
Currently we are firing a WARN when these lists are found to be
non-empty. Lets fix that to contain single bundle and connection for
control protocol.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Rui Miguel Silva [Mon, 22 Jun 2015 13:03:52 +0000 (14:03 +0100)]
greybus: sdio: extend sdio implementation
Extend sdio implementation, as it for now it was basically stubs.
This implementation is compile tested only since there is no fw or
simulation support yet.
Next step is to add sdio support to gbsim and test it with success
using the mmc_test facility.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Rui Miguel Silva [Mon, 22 Jun 2015 13:03:51 +0000 (14:03 +0100)]
greybus: makefile: add MMC to the required option list
Add MMC to the list of options that shall be enable.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Bryan O'Donoghue [Thu, 18 Jun 2015 15:41:58 +0000 (16:41 +0100)]
greybus: uart: Fix sparse warning
Greg reported sparse picked up the following warning:
/home/gregkh/ara/greybus/uart.c:105:34: warning: cast to restricted __le16
This is due to the control variable in gb_uart_serial_state_request which
needs to be declared __le16 not __u16.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reported-by: Greg Kroah-Hartman <gregkh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Bryan O'Donoghue [Tue, 16 Jun 2015 10:28:11 +0000 (11:28 +0100)]
greybus: uart: Latch modem control signals for tciomget
Latch signals coming from UART module for
- GB_UART_CTRL_DCD
- GB_UART_CTRL_DSR
- GB_UART_CTRL_RI
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Greg Kroah-Hartman [Wed, 17 Jun 2015 02:43:05 +0000 (19:43 -0700)]
greybus: Revert "greybus: reserve host cport id 0"
This reverts commit
698d4bd3e7541a660a3c3665f0af9e787650a239 as Alex
says it is broken.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Greg Kroah-Hartman [Mon, 15 Jun 2015 23:53:23 +0000 (16:53 -0700)]
greybus: Merge branch alex into Alexandre
This resolves a conflict with es2.c that I fixed up.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alexandre Bailon [Mon, 15 Jun 2015 16:08:14 +0000 (18:08 +0200)]
greybus: es2.c: add a control request for endpoints mapping
ES2 give us more endpoints. Use them to map one cport to two endpoints
(in and out). Because there is more cports than endpoints, we still
need to mux other cports traffic on 2 endpoints.
Firmware currently assumes these endpoints are 2 and 3.
By default, all cports are muxed.
To map one cport to 2 endpoints, use map_cport_to_ep().
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alexandre Bailon [Mon, 15 Jun 2015 16:08:13 +0000 (18:08 +0200)]
greybus: es2.c: Increase the number of bulk endpoints
ES2 support 16 endpoints. Update es2.c to allocate endpoints, urbs
and buffers for these new endpoints.
Currently, they are not yet used and es2.c is working in legacy mode
(only original endpoints are used).
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alexandre Bailon [Mon, 15 Jun 2015 16:08:12 +0000 (18:08 +0200)]
greybus: es2.c: create dedicated struct for cport_in and cport_out
Instead of keep cport buffers, urbs and endpoints in es1_ap_dev,
move them in two dedicated struct (es1_cport_in and es1_cport_out),
in order to ease the migration to es2 (increase the number of endpoint).
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alexandre Bailon [Mon, 15 Jun 2015 16:08:11 +0000 (18:08 +0200)]
greybus: es2.c: Don't use magic value for USB control request
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alexandre Bailon [Mon, 15 Jun 2015 16:08:10 +0000 (18:08 +0200)]
greybus: es1.c: Don't use magic value for USB control request
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Sat, 13 Jun 2015 16:02:11 +0000 (11:02 -0500)]
greybus: esX: use one byte to encode cport ids in header
We now limit the maximum value for both host and module CPort ids,
and we know they can always be represented in a single byte.
Make use of this by using only one of the two pad bytes for encoding
the CPort id in a message header.
(Note that we have never used a CPort higher than 255. Encoding
such a small CPort id in little endian 2-byte format has the same
result as what is done here.)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Sat, 13 Jun 2015 16:02:10 +0000 (11:02 -0500)]
greybus: reserve host cport id 0
For ES1 and ES2, we use pad bytes in an operation message header to
encode the CPort ID used for transferring the message. The pad
bytes should otherwise be zero, and we ensure this as the message
is passed to or from the upper layer.
If host-side CPort ID 0 is used, we have no way of knowing whether
the CPort field has been "packed" into the header.
To allow detection of this, reserve host CPort id 0. Update
cport_id_valid() to treat 0 as invalid.
(CPort ID 0 is reserved by one of the UniPro standards. We'll
assume for now that we never use it for Greybus.)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Sat, 13 Jun 2015 16:02:09 +0000 (11:02 -0500)]
greybus: rename HOST_DEV_CPORT_ID_MAX
We limit the number of host-side CPorts to a fixed maximum (which
is less than the 4096 that UniPro allows). This patch imposes a
similar limit on the CPort IDs defined by modules (signaling an
error if one too large is found in a manifest).
It seems reasonable to use the same value for both limits. Change
the name of the constant that defines the host limit and use it for
both. Update cport_id_valid() to enforce the maximum.
(Ultimately we should impose a limit like this; this change is being
made in preparation for supporting multiple connections over a
single CPort.)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Sat, 13 Jun 2015 16:02:08 +0000 (11:02 -0500)]
greybus: esX: encapsulate packing cport id into header
For the ES1 and ES2 host interfaces we encode the CPort ID over
which the message should be sent within the message itself. The
CPort ID is recorded in unused pad bytes found in the operation
message header in order to avoid introducing misaligned messages.
This patch defines some helper routines to abstract this activity.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Sat, 13 Jun 2015 16:02:07 +0000 (11:02 -0500)]
greybus: introduce cport_id_valid()
Define a public predicate that defines whether a CPort ID is valid.
Use it in the message_send() routine, and make the message reported
more accurately reflect the error. Also use it to check whether the
CPort ID in a received message is valid; if it is not, just drop the
message.
Get rid of local variable "buffer" in message_send(); it adds no
value.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 12 Jun 2015 15:21:12 +0000 (10:21 -0500)]
greybus: manifest: clean up properly when parsing bundles
Currently, if an error occurs creating a bundle, we simply
return an error without cleaning up any of the bundles that
had already been successfully set up.
Add code to destroy bundles that have been created in the event
an error occurs. Add a check to ensure the interface's list of
bundles was empty before parsing for bundles begins.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 12 Jun 2015 15:21:11 +0000 (10:21 -0500)]
greybus: bundle: fix gb_bundle_destroy()
Currently gb_bundle_destroy() takes an interface as an argument,
and really doesn't do what a function by that name should do.
What it now does is delete all bundles associated with a given
interface. What it should do is destroy a single bundle.
Move the looping logic out of gb_bundle_destroy() and into its
caller, gb_interface_destroy(). Pass each bundle in an interface to
gb_bundle_destroy(), which will do what's required to destroy a
single bundle (including removing it from its interface's bundle
list under protection of the lock).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 12 Jun 2015 15:21:10 +0000 (10:21 -0500)]
greybus: bundle: refactor gb_bundle_find()
Rearrange gb_bundle_find() so it follows the pattern used by
gb_connection_find().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 12 Jun 2015 15:21:09 +0000 (10:21 -0500)]
greybus: manifest: clean up properly when parsing cports
Currently, if an error occurs creating a connection, we simply
return an error without cleaning up any of the connections that
had already been successfully set up.
Add code to destroy connections that have been created in the event
an error occurs. Add a check to ensure the bundle's list of
connections was empty before parsing for CPorts begins.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 12 Jun 2015 15:21:08 +0000 (10:21 -0500)]
greybus: connection: un-abstract host cport id allocation
I did this recently for the endo id allocation code.
It's clearer now that the allocation of a CPort ID to use for
the AP side of a connection is not very complicated, and it
happens in a pretty controlled environment. The functions that
abstract getting and releasing those ids don't really add that
much value.
This patch removes gb_connection_hd_cport_id_alloc() and
gb_connection_hd_cport_id_free(), and just open-codes their
activity in the few places they are called.
It is obvious now that the CPort ID allocation isn't done in
atomic context, so we can change the ida_simple_get() call to
use GFP_KERNEL.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 12 Jun 2015 15:21:07 +0000 (10:21 -0500)]
greybus: connection: drop unneeded gb_protocol_put() calls
Although a connection records its protocol id when it gets
created, its protocol handler doesn't actually get assigned
until gb_connection_bind_protocol() is called.
In gb_connection_create() there are some error paths in
which a reference to the connection's protocol is released
before the protocol handler has been associated with the
connection.
Get rid of those calls.
As a result, we will never pass a null protocol pointer to
gb_protocol_put(). Add a precautionary warning in that
function in the event that ever occurs.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 12 Jun 2015 15:21:06 +0000 (10:21 -0500)]
greybus: connection: remove extra kfree() call
When an error occurs in the device_add() call for a connection, the
device reference is dropped as required. Because that's the device's
only reference, that will also lead to gb_connection_release() being
called, which frees the connection structure.
Right now we're then making an extra request to free the connection,
which is wrong. Fix that.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Phong Tran [Wed, 10 Jun 2015 14:03:17 +0000 (21:03 +0700)]
greybus: uart: fix the clean up while uart initiates connection unsucessfully
There is lack of unregister and free the tty driver.
This patch fixes it.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Greg Kroah-Hartman [Thu, 11 Jun 2015 16:22:51 +0000 (09:22 -0700)]
greybus: remove __init from .h files
__init does not belong in a .h file, as it does not do anything there,
so remove all instances of it.
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Viresh Kumar [Thu, 11 Jun 2015 11:09:42 +0000 (16:39 +0530)]
greybus: endo: Fix compilation warning
WARNING: /home/viresh/work/repos/ara/greybus/greybus.o(.init.text+0xb8):
Section mismatch in reference from the function init_module() to the
function .exit.text:gb_endo_exit()
The function __init init_module() references
a function __exit gb_endo_exit().
Fix it by removing __exit from endo_exit().
Fixes:
cf64356c5151 ("endo: define endo_init() and endo_exit()")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Tue, 9 Jun 2015 22:42:58 +0000 (17:42 -0500)]
greybus: connection: check for duplicate cport ids
Check at connection creation time for an attempt to create a
connection with an interface CPort ID that's the same as one that's
already been created.
Define a new helper function to look for such a duplicate. The
check for a duplicate is only performed at initialization time,
and CPorts are initialized serially for each bundle, so there's
no need to acquire the list lock for this search.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Tue, 9 Jun 2015 22:42:57 +0000 (17:42 -0500)]
greybus: bundle: check for duplicate bundle ids
Check at bundle creation time to ensure we're not creating a bundle
with an id that's the same as one that's already been created.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Tue, 9 Jun 2015 22:42:56 +0000 (17:42 -0500)]
greybus: manifest: rework bundle parsing
Rework the the code that parses the manifest for bundles so it only
touches each manifest descriptor once. (Previously the list was
scanned from the beginning repeatedly until all bundles were found.)
Shorten the name of the descriptor variable, to avoid line wrap.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Tue, 9 Jun 2015 22:42:55 +0000 (17:42 -0500)]
greybus: manifest: rework cport parsing
Rework the the code that parses the manifest for CPorts associated
with a bundle so it only touches each manifest descriptor once.
(Previously the list was scanned from the beginning repeatedly
until all bundle CPorts were found.) Shorten the name of the
descriptor variable, to avoid line wrap.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Tue, 9 Jun 2015 22:42:54 +0000 (17:42 -0500)]
greybus: manifest: use bundle's embedded interface pointer
An initialized bundle structure contains a pointer to its
interface. Because of this there's no need to provide
the interface pointer to gb_manifest_parse_cports(). This
also precludes the possibility of passing a bad interface
pointer.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Tue, 9 Jun 2015 22:42:53 +0000 (17:42 -0500)]
greybus: manifest: really minor cleanups
This patch incorporates some very small cleanups to "manifest.c":
- Rearrange code a bit in gb_manifest_parse() that ensures a
manifest is big enough to hold a header. If the manifest is
exactly the size of a header, the error reported will now be
"...must have 1 interface..." rather than "short manifest".
- Fix the function comment for gb_manifest_parse_cports().
- Use "an interface," not "a interface," and don't capitalize.
- Delete some braces when getting interface product string.
- A few other minor changes to comments and white space.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Tue, 9 Jun 2015 22:42:52 +0000 (17:42 -0500)]
greybus: endo: clean up id assignment code
Recently code was added (back) to assign a unique id to each
endo, so satisfy uniqueness requirements of the Linux device
subsystem. An ID allocator is used to manage the space of IDs.
Now that we have gb_endo_init(), we can initialize the map there,
and fully hide the ID map within "endo.c".
The original functions gb_endo_id_alloc() and gb_endo_id_free()
provided a nice abstract interface, but the direct ID allocation
calls are quite simple, so just call them directly.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Tue, 9 Jun 2015 22:42:51 +0000 (17:42 -0500)]
greybus: endo: define endo_init() and endo_exit()
Define init and exit functions to do one-time setup and teardown
of endo-related functionality. Currently they're place holders;
the next patch will populate them.
Note that we now call gb_operation_exit() from gb_init(), so
we can no longer mark that function with __exit.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Tue, 9 Jun 2015 22:42:50 +0000 (17:42 -0500)]
greybus: tag core init and exit functions
The top-level functions gb_init() and gb_exit() are tagged with
__init and __exit, respectively. These functions call a few
other functions that are similarly used only at initialization
and termination time. So mark those functions accordingly.
Note that, because gb_ap_exit() and gb_debugfs_cleanup()
are called by gb_init() in error paths, these functions
cannot be declared with the __exit attribute.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Tue, 9 Jun 2015 22:42:49 +0000 (17:42 -0500)]
greybus: drop some unnecessary headers
There's no need to include anything other than "greybus.h" in
"connection.c". Same thing in "core.c" and "manifest.c" and
"svc.c". Some files need headers included, but most come along
with "greybus.h".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Mark Greer [Tue, 9 Jun 2015 22:29:35 +0000 (15:29 -0700)]
greybus: gb-audio: Reset sample count when CPort deactivated
The sample count placed in Greybus I2S audio messages should be
reset every time a new audio stream is set up. However, the
current code does not do the reset so make it so it does.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Greg Kroah-Hartman [Tue, 9 Jun 2015 20:47:48 +0000 (13:47 -0700)]
greybus: es?: decrease buffer size to 2k
The firmware is having a hard time with 4k buffers and memory
allocation, so decrease the size on the host side to 2k. Also move away
from using PAGE_SIZE to denote 4k as that's not the case on all
architectures, and someone, someday, might get a rude surprise.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Phong Tran [Tue, 9 Jun 2015 13:28:18 +0000 (20:28 +0700)]
greybus: uart: remove the redundant unregister chrdev
The unregister_chrdev_region() does twice here.
The chrdev region was unregistered
inside tty_unregister_driver().
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Phong Tran [Tue, 9 Jun 2015 13:28:17 +0000 (20:28 +0700)]
greybus: endo: move endo id map declaration to endo.h
There is a sparse warning. The endo id map is also
used in endo.c. Should define in endo.h
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Viresh Kumar [Thu, 4 Jun 2015 12:46:45 +0000 (18:16 +0530)]
greybus: Tear down devices in the reverse order
Normally, its a good practice to free resources in the reverse order in
which they are allocated, so that all the dependencies can be sorted out
properly.
This is true while creating/destroying devices as well. For example
consider this scenario (I faced a crash with control protocol due to
this). For a new module, we will first create a bundle+connection for
the control cport and then create other bundles/connections after
parsing manifest.
And while destroying interface on module hot unplug, we are removing the
devices in the order they are added. And so the bundle/connection for
the control cport are destroyed first. But, control cport was still
required while destroying other bundles/connections.
To solve this problem, lets destroy the resources in the reverse order
in which they are added.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Mon, 8 Jun 2015 17:05:14 +0000 (12:05 -0500)]
greybus: manifest: clean up a few pr_err() calls
Provide a little more information in two pr_err() calls.
Also enclose a reported condition in parentheses, to match
the style used everywhere else in the file.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Mon, 8 Jun 2015 17:05:13 +0000 (12:05 -0500)]
greybus: core: rename greybus_deregister()
Rename greybus_deregister() to be greybus_deregister_driver(), so
its name mirrors the greybus_register_driver() function it matches.
Define greybus_deregister() to be a trivial macro.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Mon, 8 Jun 2015 17:05:12 +0000 (12:05 -0500)]
greybus: uart: properly interpret receive data size
In gb_uart_request_recv(), the receive data size is in little-endian
format. Do the proper byte swapping of that value before using it.
Found by "make check".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Mon, 8 Jun 2015 17:05:11 +0000 (12:05 -0500)]
greybus: connection: make gb_connection_hd_find() private
Give gb_connection_hd_find() static scope; it's never used
outside "connection.c".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Mon, 8 Jun 2015 17:05:10 +0000 (12:05 -0500)]
greybus: svc: driver is basic to Greybus (not GP Bridge)
The SVC protocol driver should have been defined as a basic
Greybus protocol driver, not a GP Bridge protocol driver.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Viresh Kumar [Sun, 7 Jun 2015 03:43:16 +0000 (09:13 +0530)]
greybus: Prefix module-id with endo id
Prefix module-id with endo-id to uniquely identify it for the entire
kernel.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Viresh Kumar [Sun, 7 Jun 2015 03:43:15 +0000 (09:13 +0530)]
greybus: Generate greybus wide unique ids for endo devices
Currently we name the endo device as "endo". And it shows up with the
same name in sysfs directory: /sys/bus/greybus/devices/.
But each device in kernel should be represented by a unique id in
kernel, and "endo" isn't unique.
Lets generate unique ids for endo devices. The ida mechanism for
allocating ids may be overkill but it works.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Viresh Kumar [Thu, 4 Jun 2015 04:48:01 +0000 (10:18 +0530)]
greybus: s/bundle_cport_id/intf_cport_id
This isn't unique just for the bundle but the complete interface. Its
wrong to call it bundle_cport_id. Lets name it intf_cport_id to make
things clear.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Viresh Kumar [Thu, 4 Jun 2015 04:28:21 +0000 (09:58 +0530)]
greybus: operation: Remove unused variable 'buffer'
'buffer' isn't used in this function, remove it.
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Bryan O'Donoghue [Tue, 2 Jun 2015 12:40:51 +0000 (13:40 +0100)]
greybus: uart: Remove magic numbers make struct gb_tty variable names consistent
Use defines for the data format command.
Tidy up naming of gb_tty variables.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Bryan O'Donoghue [Tue, 2 Jun 2015 12:40:50 +0000 (13:40 +0100)]
greybus: uart: Add gb_uart_request_recv for receiving async UART data
gb_uart_request_recv job in life is to process unsolicited greybus
mesages from the UART.
Hook the incoming UART data and pass to the TTY layer.
Line-state changes still TBD.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Bryan O'Donoghue [Tue, 2 Jun 2015 12:40:49 +0000 (13:40 +0100)]
greybus: uart: kmalloc for send_data once only
Make kmalloc for the send buffer a one time alloc based on the MTU for
a given greybus link.
The write_room for an gb_operation_sync then will be the size of the
buffer we use for a single operation.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Bryan O'Donoghue [Tue, 2 Jun 2015 12:40:48 +0000 (13:40 +0100)]
greybus: uart: send_data should return size or error
gb_operation_sync returns 0 on success but the calling function
expects the number of bytes written on success or a negative errno
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Bryan O'Donoghue [Tue, 2 Jun 2015 12:40:47 +0000 (13:40 +0100)]
greybus: uart: Update uart.c to register tty ports
For each new UART connection we need to do a tty_port_init else
we'll crash when trying to access the tty mutex later on.
Base the TTY major/minor numbers on non-zero values.
Supply an empty operations structure for the newly regitered port.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Bryan O'Donoghue [Tue, 2 Jun 2015 12:40:46 +0000 (13:40 +0100)]
greybus: uart: Reduce UART count from 255 to 16
Arbitrary number 255 is both not aligned and probably too big.
Move the UART count down to 16 which is still large but, more realistic.
8 may be too few for future testing setups, 16 should accomodate any.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Bryan O'Donoghue [Tue, 2 Jun 2015 12:40:45 +0000 (13:40 +0100)]
greybus: uart: Tidy naming convention to more closely match spec
Update tabs and naming of structures to match the naming used in the greybus
specification more closely.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Bryan O'Donoghue [Tue, 2 Jun 2015 12:40:44 +0000 (13:40 +0100)]
greybus: uart: Move UART protocol structs/defines to greybus_protocols.h
gbsim depends on the structures and defines in greybus_protocols.h
generally in order to simulate firmware. Move UART defines into this
header to facilitate.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Phong Tran [Mon, 1 Jun 2015 15:19:45 +0000 (22:19 +0700)]
greybus: uart: Fix the memory leak in connection init
If alloc minor is error, gb_tty should free.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Viresh Kumar [Mon, 1 Jun 2015 12:13:36 +0000 (17:43 +0530)]
greybus: endo: Add missing '\n' sprintf() for sysfs files
Because of the missing '\n', this is how the output of reading endo
sysfs files looks:
root# cat /sys/bus/greybus/devices/endo/id
0x4755root#
Fix it by including \n to the end of the printed string.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Johan Hovold [Thu, 28 May 2015 17:03:34 +0000 (19:03 +0200)]
greybus: gpio: add irq-type defines
Add Greybus GPIO IRQ-type defines rather than rely on the current
Linux implementation.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Johan Hovold [Thu, 28 May 2015 17:03:33 +0000 (19:03 +0200)]
greybus: gpio: remove unused debounce define
Remove unused debounce define from protocol header.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Wed, 27 May 2015 16:17:53 +0000 (11:17 -0500)]
greybus: endo: delete "0xXXXX" portion in sysfs "endo" directory
With the Endo "id" attribute in place, there's no need to encode
the ID of an Endo in its sysfs path. So get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Wed, 27 May 2015 16:17:52 +0000 (11:17 -0500)]
greybus: endo: drop redundant prefixes from sysfs basenames
This commit:
7e761e2 endo: rework some attributes
added a new "endo_id" attribute, located under a new "Endo"
directory in sysfs. The resulting path looks like:
Documentation/sysfs/endo-TYPE/Endo/endo_id
There's no need to have a separate "Endo" subdirectory to contain
Endo-specific attributes.
That commit also added "svc_" to some other paths related to the
SVC, like:
Documentation/sysfs/endo-TYPE/SVC/svc_version
The additional "svc_" is redundant.
This patch retouches those paths a bit, mainly to remove some
redundancy. It also makes the pathname components all lower case.
As a result, the above two paths now look like:
Documentation/sysfs/endo-TYPE/id
Documentation/sysfs/endo-TYPE/svc/version
All other Endo sysfs files are updated similarly.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Wed, 27 May 2015 16:17:51 +0000 (11:17 -0500)]
greybus: update sysfs documentation files
Impose a few editorial conventions on the Greybus-related sysfs
files under "Documentation".
- Capitalize "Endo" (except in path names)
- Capitalize "ID" (except in path names)
- Use "..." to indicate unspecified path components (because
".." means something else).
- Add the "0x" prior to the "XXXX" representing the Endo ID.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Wed, 27 May 2015 16:17:50 +0000 (11:17 -0500)]
greybus: add documentation for Endo sysfs files
Update the files documenting Greybus-related sysfs files under
Documentation/ to reflect the addition of the two recently-added
Endo attributes.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Phong Tran [Thu, 28 May 2015 16:21:01 +0000 (23:21 +0700)]
greybus: audio: Remove the MODULE_LICENSE()
This is not a kernel module. It should not use
the module license macro.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Phong Tran [Thu, 28 May 2015 16:21:00 +0000 (23:21 +0700)]
greybus: audio: Fix typo for macro I2S data version minor
This macro should be DATA not MGMT.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Wed, 27 May 2015 19:45:58 +0000 (14:45 -0500)]
greybus: greybus_protocols: fix guard tag
I neglected to update the "#ifndef/#define" when I renamed
"greybus_protocols.h". Fix that.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Johan Hovold [Wed, 27 May 2015 10:45:07 +0000 (12:45 +0200)]
greybus: gpio: update operation types
Update the remaining operation types now that the ack operation is gone
to avoid leaving a hole in the type definitions.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Greg Kroah-Hartman [Thu, 28 May 2015 21:02:02 +0000 (14:02 -0700)]
greybus: Merge branch 'master' of github.com:gregkh/greybus
Phong Tran [Wed, 27 May 2015 14:31:03 +0000 (21:31 +0700)]
greybus: svc: use macro for init and exit protocol
Change to gb_gpbridge_protocol_driver for
making the consitent with other drivers.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Phong Tran [Wed, 27 May 2015 14:31:02 +0000 (21:31 +0700)]
greybus: svc: Fix endian of hotplug request data
data of hotplug request should exchange to native
CPU format before assignment.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Johan Hovold [Tue, 26 May 2015 13:29:25 +0000 (15:29 +0200)]
greybus: gpio: fix interrupt protocol
The current interrupt implementation uses the simple irq-flow handler,
which means that the interrupt subsystem makes no irq-chip callbacks
when handling an interrupt. Specifically, no end-of-interrupt message is
sent when the threaded handler has run. This means that we may currently
re-enable an interrupt before it has been serviced (i.e. the irq-event
operation may complete before the threaded handler has run).
The simple flow handler also silently drops a second interrupt arriving
while a handler is running. This means that we may lose a second edge
interrupt with the current firmware.
Switch to a new one-shot interrupt protocol, where the primary handler
(firmware) always masks and acks an interrupt before sending an event to
the AP. The AP is responsible for unmasking the interrupt when it has
been handled. By having the firmware ack an edge interrupt before
sending the event, a second edge interrupt will no longer get lost.
This one-shot protocol can be implemented in the kernel by using the
level irq-flow handler, one-shot interrupts with threaded handlers and
bus-lock synchronisation for slow buses. Note that the same flow handler
is used for both edge and level interrupts.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Johan Hovold [Tue, 26 May 2015 13:29:24 +0000 (15:29 +0200)]
greybus: gpio: fix atomic sleep when using interrupts
The irq-chip callbacks are made in atomic context where we must not do
any synchronous greybus operations.
Fix the current gpio-interrupt implementation by using the bus-lock
functionality provided by the irq subsystem.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Johan Hovold [Tue, 26 May 2015 13:29:23 +0000 (15:29 +0200)]
greybus: gpio: rename irq mask and unmask callbacks
Rename irq mask and unmask functions to match the callback names.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Johan Hovold [Tue, 26 May 2015 13:29:22 +0000 (15:29 +0200)]
greybus: gpio: use irq-domain lookups
Use irq_find_mapping directly rather than go through the legacy gpio
interface.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Johan Hovold [Tue, 26 May 2015 13:29:21 +0000 (15:29 +0200)]
greybus: gpio: don't call irq-flow handler directly
Use generic_handle_irq_desc rather than call a hardcoded irq-flow
handler directly.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Johan Hovold [Tue, 26 May 2015 13:29:20 +0000 (15:29 +0200)]
greybus: gpio: remove unused irq-ack operation
Remove unused irq-ack operation, which has never been called and does
not make sense for message-signalled interrupts over slow buses.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Johan Hovold [Tue, 26 May 2015 13:29:19 +0000 (15:29 +0200)]
greybus: gpio: fix debugfs output
Fix debugfs output by removing the unimplemented, custom dbg_show
callback. The default implementation is perfectly sufficient.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Johan Hovold [Tue, 26 May 2015 13:29:18 +0000 (15:29 +0200)]
greybus: operation: add support for incoming unidirectional operations
Add support for incoming, unidirectional operations where the sender of
a request does not care about a response.
Unidirectional operations have an operation id of 0.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Greg Kroah-Hartman [Tue, 26 May 2015 15:39:33 +0000 (08:39 -0700)]
greybus: Merge branch 'master' of github.com:gregkh/greybus
Alex Elder [Fri, 22 May 2015 18:02:08 +0000 (13:02 -0500)]
greybus: introduce SVC protocol
This patch adds support for the Greybus SVC protocol. We may want
to rearrange protocol numbers at some point, since this is a pretty
fundamental protocol.
Note: It has only been compile tested; no SVC CPorts have yet been
defined, so this code is not yet exercised.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 22 May 2015 17:59:16 +0000 (12:59 -0500)]
greybus: update copyrights
Update the copyright statements for recently-modified source files.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 22 May 2015 17:59:15 +0000 (12:59 -0500)]
greybus: add copyright statements
The Greybus audio source files included no copyright statements.
Add them.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 22 May 2015 17:56:49 +0000 (12:56 -0500)]
greybus: core: don't set up endo until host device is initialized
Currently, the data structure representing an Endo is set up at the
time a host device gets created. This is too early.
Once the control infrastructure is in place, there's no sense in
setting up the Endo utnil after we have heard from the SVC via a
probe operation on our control CPort. And even then, there's
no real point until we've successfully authenticated with the SVC,
which will be indicated by the arrival of the Control protocol
"connected" operation request notifying us that our SVC CPort
is operational.
In addition to this logical argument, we also can't actually
receive any messages on the Control CPort until the host device
is set up and ready to receive messages. At the point we're
currently setting up the Endo data structure, that has not yet
been done.
Define a new exported function greybus_endo_setup(), which will
be used (for now) as the entry point for setting up the Endo
data structure. Arrange to call it in the host USB driver
probe method, *after* we are set up for handling messages.
Note: Once the control protocol has been implemented, this function
may no longer need to be exported.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 22 May 2015 17:56:48 +0000 (12:56 -0500)]
greybus: endo: record AP interface id
The AP resides in a particular position on an Endo, which is
identified by an interface ID. (For now we'll assume the AP uses
just one interface.) Record the this AP interface ID when creating
an Endo. Add a sysfs attribute to display it as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 22 May 2015 17:56:47 +0000 (12:56 -0500)]
greybus: endo: rework some attributes
The SVC is not the same as the Endo. There are some attributes
(such as the Endo ID) that are independent of attributes of
the SVC (like its version).
The current "Endo attributes" are really SVC attributes.
Rename a few functions and variables to reflect that.
Add a new attribute group for Endo-specific attributes, and
populate it with the Endo ID.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 22 May 2015 17:56:46 +0000 (12:56 -0500)]
greybus: endo: encapsulate computing the max interface id
The maximum interface id on an Endo is the result of a non-trivial
calculation. It'll be needed for an upcoming patch, so create a
macro to compute it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 22 May 2015 17:35:32 +0000 (12:35 -0500)]
greybus: rename "gpbridge.h"
The file "gpbridge.h" is now used as a single place to define
all protocol message structures. These protocols are not
necessarily related to the GP bridge, so the name of the
file is misleading.
Rename it "greybus_protocols.h".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 22 May 2015 17:35:31 +0000 (12:35 -0500)]
greybus: include "gpbridge.h" from "greybus.h"
Avoid the need for all the source files to include "gpbridge.h"
by just having "greybus.h" include it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 22 May 2015 14:52:45 +0000 (09:52 -0500)]
greybus: core: return error code when creating host device
Return a pointer-coded error from greybus_create_hd() rather
than NULL in the event an error occurs.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 22 May 2015 14:52:44 +0000 (09:52 -0500)]
greybus: core: return error code when creating endo
Return a pointer-coded error from gb_endo_create() rather than just
a null pointer in the event an error occurs.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 22 May 2015 14:52:43 +0000 (09:52 -0500)]
greybus: endo: pass endo_id to gb_endo_create()
We are going to want to defer creating the endo until we receive a
probe operation from the SVC, which will supply the endo id. Change
gb_endo_create() so it passes the endo_id value as an argument.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex Elder [Fri, 22 May 2015 14:52:42 +0000 (09:52 -0500)]
greybus: endo: rename gb_svc
Change the name of "struct gb_svc" to be "struct svc_info". The
structure now contains only the SVC's serial number and version (and
are place holders anyway). We will be defining a structure that
represents the SVC for the SVC protocol connection, and I want to
take back that name.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Mark A. Greer [Thu, 21 May 2015 22:57:04 +0000 (15:57 -0700)]
greybus: gb-audio: Set samples per message during init
A recent commit moved the I2S samples per message operation
to the PCM's 'hw_params' callback. However, the 'hw_params'
callback is called numerous times while the samples per
message need only be done once (or seldom). Eliminate the
unnecessary samples per message operations by doing it only
once at Greybus protocol init time.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Mark A. Greer [Thu, 21 May 2015 22:57:03 +0000 (15:57 -0700)]
greybus: gb-audio: Set I2S Configuration according to ASOC requests
Currently, the audio driver unconditionally sets the I2S
configuration to have a sample rate of 48KHz, two channels,
16 bits per channel, in little endian order. Make this
more flexible by setting the I2S configuration according to
the arguments passed to the PCM 'hw_params' callback.
To accomplish this, query for the supported I2S configurations
at Greybus protocol init time and save them in the 'snd_dev'
structure. When the 'hw_params' callback is called, compare its
arguments to the table of supported configurations. If there is
a match, set the I2S connection accordingly.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Mark A. Greer [Thu, 21 May 2015 22:57:02 +0000 (15:57 -0700)]
greybus: gb-audio: Activate TX connection Bundle CPort ID
Currently, the audio driver activates & deactivates a predefined
CPort ID but that can vary depending on the manifest data of the
module. Instead, use the TX connection's Bundle CPort ID which
contains the correct CPort ID.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>