OSDN Git Service
Quinn Tran [Fri, 30 Aug 2019 22:24:00 +0000 (15:24 -0700)]
scsi: qla2xxx: Fix stuck login session
Login session was stucked on cable pull. When FW is in the middle PRLI
PENDING + driver is in Initiator mode, driver fails to check back with FW to
see if the PRLI has completed. This patch would re-check with FW again to
make sure PRLI would complete before pushing forward with relogin.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Link: https://lore.kernel.org/r/20190830222402.23688-5-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Himanshu Madhani [Fri, 30 Aug 2019 22:23:59 +0000 (15:23 -0700)]
scsi: qla2xxx: Fix driver reload for ISP82xx
HINT_MBX_INT_PENDING is not guaranteed to be cleared by firmware. Remove
check that prevent driver load with ISP82XX.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Link: https://lore.kernel.org/r/20190830222402.23688-4-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 30 Aug 2019 22:23:58 +0000 (15:23 -0700)]
scsi: qla2xxx: Fix flash read for Qlogic ISPs
Use adapter specific callback to read flash instead of ISP adapter
specific.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Link: https://lore.kernel.org/r/20190830222402.23688-3-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Himanshu Madhani [Fri, 30 Aug 2019 22:23:57 +0000 (15:23 -0700)]
scsi: qla2xxx: Fix message indicating vectors used by driver
This patch updates log message which indicates number of vectors used by
the driver instead of displaying failure to get maximum requested
vectors. Driver will always request maximum vectors during
initialization. In the event driver is not able to get maximum requested
vectors, it will adjust the allocated vectors. This is normal and does not
imply failure in driver.
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Link: https://lore.kernel.org/r/20190830222402.23688-2-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Damien Le Moal [Wed, 28 Aug 2019 05:35:11 +0000 (14:35 +0900)]
scsi: sd: Improve unaligned completion resid message
For commands completing with a resid not aligned on the device logical
sector size, also print the command CDB in addition to the current message
to help debug hardware generating such incorrect command completion
information.
Link: https://lore.kernel.org/r/20190828053511.14818-1-damien.lemoal@wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Govindarajulu Varadarajan [Tue, 27 Aug 2019 21:13:40 +0000 (14:13 -0700)]
scsi: fnic: fix msix interrupt allocation
pci_alloc_irq_vectors() returns number of vectors allocated. Fix the check
for error condition.
Fixes:
cca678dfbad49 ("scsi: fnic: switch to pci_alloc_irq_vectors")
Link: https://lore.kernel.org/r/20190827211340.1095-1-gvaradar@cisco.com
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Acked-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Pittman [Fri, 23 Aug 2019 14:08:52 +0000 (10:08 -0400)]
scsi: fnic: print port speed only at driver init or speed change
Port speed printing was added by commit
d948e6383ec3 ("scsi: fnic: Add port
speed stat to fnic debug stats"). As currently configured, this will cause
the port speed to be printed to syslog every 2 seconds. To prevent log
spamming, only print the vnic port speed at driver initialization and if
the speed changes. Also clean up a small typo in fnic_trace.c.
Fixes:
d948e6383ec3 ("scsi: fnic: Add port speed stat to fnic debug stats")
Signed-off-by: John Pittman <jpittman@redhat.com>
Reviewed-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
zhengbin [Fri, 23 Aug 2019 13:22:53 +0000 (21:22 +0800)]
scsi: bnx2fc: remove set but not used variables 'task','port','orig_task'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/bnx2fc/bnx2fc_hwi.c: In function bnx2fc_process_unsol_compl:
drivers/scsi/bnx2fc/bnx2fc_hwi.c:636:30: warning: variable task set but not used [-Wunused-but-set-variable]
drivers/scsi/bnx2fc/bnx2fc_hwi.c: In function bnx2fc_process_ofld_cmpl:
drivers/scsi/bnx2fc/bnx2fc_hwi.c:1125:21: warning: variable port set but not used [-Wunused-but-set-variable]
drivers/scsi/bnx2fc/bnx2fc_hwi.c: In function bnx2fc_init_seq_cleanup_task:
drivers/scsi/bnx2fc/bnx2fc_hwi.c:1468:30: warning: variable orig_task set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
zhengbin [Fri, 23 Aug 2019 13:22:52 +0000 (21:22 +0800)]
scsi: bnx2fc: remove set but not used variables 'lport','host'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/bnx2fc/bnx2fc_io.c: In function bnx2fc_initiate_seq_cleanup:
drivers/scsi/bnx2fc/bnx2fc_io.c:932:19: warning: variable lport set but not used [-Wunused-but-set-variable]
drivers/scsi/bnx2fc/bnx2fc_io.c: In function bnx2fc_initiate_cleanup:
drivers/scsi/bnx2fc/bnx2fc_io.c:1001:19: warning: variable lport set but not used [-Wunused-but-set-variable]
drivers/scsi/bnx2fc/bnx2fc_io.c: In function bnx2fc_process_scsi_cmd_compl:
drivers/scsi/bnx2fc/bnx2fc_io.c:1882:20: warning: variable host set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
zhengbin [Fri, 23 Aug 2019 13:22:51 +0000 (21:22 +0800)]
scsi: bnx2fc: remove set but not used variable 'fh'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/bnx2fc/bnx2fc_fcoe.c: In function bnx2fc_rcv:
drivers/scsi/bnx2fc/bnx2fc_fcoe.c:431:26: warning: variable fh set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:44 +0000 (02:52 -0700)]
scsi: qedf: Update the version to 8.42.3.0
Update the driver version to 8.42.3.0.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:43 +0000 (02:52 -0700)]
scsi: qedf: Fix race betwen fipvlan request and response path
There is a race b/w fipvlan request and response path:
=====
qedf_fcoe_process_vlan_resp:113]:2: VLAN response, vid=0xffd.
qedf_initiate_fipvlan_req:165]:2: vlan = 0x6ffd already set.
qedf_set_vlan_id:139]:2: Setting vlan_id=0ffd prio=3.
======
The request thread sees that vlan is already set and fails to call
ctrl_link_up.
Fix:
- While setting vlan_id use local variable and before setting vlan_id.
- Call fcoe_ctlr_link_up in next iteration of fipvlan request.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Fri, 23 Aug 2019 09:52:42 +0000 (02:52 -0700)]
scsi: qedf: Use discovery list to traverse rports
The list of rports might become stale so we should rather traverse the
discovery list when trying relogin.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:41 +0000 (02:52 -0700)]
scsi: qedf: Decrease the LL2 MTU size to 2500
Decrease the LL2 MTU size to 2500.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:40 +0000 (02:52 -0700)]
scsi: qedf: Check for module unloading bit before processing link update AEN
Prevent race where we're removing the module and we get link update
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:39 +0000 (02:52 -0700)]
scsi: qedf: Initiator fails to re-login to switch after link down
Problem Statement:
- Driver has fc_id of 0xcc0200
- Driver gets link down (due to test) and calls fcoe_ctlr_link_down().
- At this point, the fc_id of the initiator port is zeroed out.
- Driver gets a link up 14 seconds later.
- Driver performs FIP VLAN request, gets a response from the switch.
- No change in VLAN is detected.
- Driver then notifies libfcoe via fcoe_ctlr_link_up().
- Libfcoe then issues a multicast discovery solicitation as expected.
- Cisco FCF responds to that correctly.
- Libfcoe at this point starts a 3 sec count-down to allow any other FCFs
to be discovered. However, at this point, it has been 20 seconds since
the last FKA from the driver (which would have been sent prior to
backlink toggle), which causes the CVL to be issued from Cisco CVL from
the switch is dropped by the driver as the vx_port identification
descriptor is present and has value of 0xcc0200, which does not match
the driver's value of 0. Libfcoe completes the 3 sec count down and
proceeds to issue FLOGI as per protocol. Switch rejects FLogi request.
All subsequent FLOGI requests from libfc are rejected by the switch
(possibly because it is now expecting a new solicitation). This
situation will continue until the next link toggle.
Solution:
The Vx_port descriptor in the CVL has three fields:
MAC address
Fabric ID
Port Name
Today, the code checks for both #1 and #2 above. In the case where we went
through a link down, both these will be zero until FLOGI succeeds.
We should change our code to check if any one of these 3 is valid and if
so, handle the CVL (basically switching from AND to OR). The port name
field is definitely expected to be valid always.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:38 +0000 (02:52 -0700)]
scsi: qedf: Add debug information for unsolicited processing
Log s_id, d_id, type and command to the log message.
[mkp: fixed warning]
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:37 +0000 (02:52 -0700)]
scsi: qedf: Add support for 20 Gbps speed
The current code doeesn't support 20Gbps speed for current and supported
speed. Add support for it.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:36 +0000 (02:52 -0700)]
scsi: qedf: Interpret supported caps value correctly
Driver was wrongly interpreting the supported cap value returned by qed.
Solution: Use QED define macros instead of OS defined for interpreting
supporting speeds.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:35 +0000 (02:52 -0700)]
scsi: qedf: Add shutdown callback handler
Add shutdown callback handler.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nilesh Javali [Fri, 23 Aug 2019 09:52:34 +0000 (02:52 -0700)]
scsi: qedf: Update module description string
Update module description.
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arun Easi [Fri, 23 Aug 2019 09:52:33 +0000 (02:52 -0700)]
scsi: qedf: Fix crash during sg_reset
Driver was attempting to print cdb[0], which is not set for resets coming
from SCSI ioctls. Check for cmd_len before accessing cmnd.
Crash info:
[84790.864747] BUG: unable to handle kernel NULL pointer dereference at (null)
[84790.864783] IP: qedf_initiate_tmf+0x7a/0x6e0 [qedf]
[84790.865204] Call Trace:
[84790.865246] scsi_try_target_reset+0x2b/0x90 [scsi_mod]
[84790.865266] scsi_ioctl_reset+0x20f/0x2a0 [scsi_mod]
[84790.865284] scsi_ioctl+0x131/0x3a0 [scsi_mod]
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:32 +0000 (02:52 -0700)]
scsi: qedf: Stop sending fipvlan request on unload
- On some setups fipvlan can be retried for long duration and the
connection to switch was not there so it was not getting any reply.
- During unload this thread was hanging.
Problem Resolution:
Check if unload is in progress, then quit from fipvlan thread.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:31 +0000 (02:52 -0700)]
scsi: qedf: Print message during bailout conditions
Print messages during exiting condition to help debugging.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don Brace [Thu, 22 Aug 2019 20:40:05 +0000 (15:40 -0500)]
scsi: smartpqi: bump version
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don Brace [Thu, 22 Aug 2019 20:39:58 +0000 (15:39 -0500)]
scsi: smartpqi: update copyright
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gilbert Wu [Thu, 22 Aug 2019 20:39:51 +0000 (15:39 -0500)]
scsi: smartpqi: add new pci ids
Add:
PM8222 VID_9005, DID_028F, SVID_1BD4 and SDID_004F
3101E-4i (1G, no GB) VID_9005, DID_028F, SVID_9005 and SDID_0808
3102E-8i (2G, no GB) VID_9005, DID_028F, SVID_9005 and SDID_0809
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Murthy Bhat [Thu, 22 Aug 2019 20:39:44 +0000 (15:39 -0500)]
scsi: smartpqi: correct REGNEWD return status
Return -EINPROGRESS when a rescan worker is queued.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gilbert Wu [Thu, 22 Aug 2019 20:39:38 +0000 (15:39 -0500)]
scsi: smartpqi: add gigabyte controller
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mahesh Rajashekhara [Thu, 22 Aug 2019 20:39:31 +0000 (15:39 -0500)]
scsi: smartpqi: correct hang when deleting 32 lds
When each ld is deleted, a rescan event is triggered in the driver. These
can stack up waiting on mutex_lock.
Change to mutex_try_lock and schedule a rescan for later.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gilbert Wu [Thu, 22 Aug 2019 20:39:25 +0000 (15:39 -0500)]
scsi: smartpqi: add bay identifier
Return identify physical device "Phys_Bay_in_Box" as bay_identifier.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Murthy Bhat [Thu, 22 Aug 2019 20:39:18 +0000 (15:39 -0500)]
scsi: smartpqi: add sysfs entries
- serial number
- model
- vendor
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dave Carroll [Thu, 22 Aug 2019 20:39:11 +0000 (15:39 -0500)]
scsi: smartpqi: add module param to hide vsep
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gilbert Wu [Thu, 22 Aug 2019 20:39:04 +0000 (15:39 -0500)]
scsi: smartpqi: add pci ids for fiberhome controller
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gilbert Wu [Thu, 22 Aug 2019 20:38:58 +0000 (15:38 -0500)]
scsi: smartpqi: add module param for exposure order
Expose physical devices before logical devices.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 28 Aug 2019 23:19:11 +0000 (16:19 -0700)]
scsi: lpfc: fix 12.4.0.0 GPF at boot
The 12.4.0.0 patch that merged WQ/CQ pairs into single per-cpu pair
contained a bug: a local variable was set to the queue pair by index. This
should have allowed the local variable to be natively used. Instead, the
code reused the index relative to the local variable, obtaining a random
pointer value that when used eventually faulted the system
Convert offending code to use local variable.
Fixes:
c00f62e6c546 ("scsi: lpfc: Merge per-protocol WQ/CQ pairs into single per-cpu pair")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 27 Aug 2019 21:28:05 +0000 (14:28 -0700)]
scsi: lpfc: Remove bg debugfs buffers
Capturing and downloading dif command data and dif data was done a dozen
years ago and no longer being used. Also creates a potential security hole.
Remove the debugfs buffer for dif debugging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: KyleMahlkuch <kmahlkuc@linux.vnet.ibm.com>
CC: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 27 Aug 2019 21:27:46 +0000 (14:27 -0700)]
scsi: lpfc: Resolve checker warning for lpfc_new_io_buf()
Per Dan Carpenter:
The patch
d79c9e9d4b3d: "scsi: lpfc: Support dynamic unbounded SGL lists on
G7 hardware." from Aug 14, 2019, leads to the following static checker
warning:
drivers/scsi/lpfc/lpfc_init.c:4107 lpfc_new_io_buf()
error: not allocating enough data 784 vs 768
There was no need to compare sizes nor to allocate size based on a define.
Change allocation to use actual structure length
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
zhengbin [Mon, 26 Aug 2019 01:15:49 +0000 (09:15 +0800)]
scsi: ufs: remove set but not used variable 'val'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/ufs/ufs-qcom.c: In function ufs_qcom_pwr_change_notify:
drivers/scsi/ufs/ufs-qcom.c:808:6: warning: variable val set but not used [-Wunused-but-set-variable]
Fixes:
1e1e465c6d23 ("scsi/ufs: qcom: Remove ufs_qcom_phy_*() calls from host")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Thu, 22 Aug 2019 21:56:51 +0000 (22:56 +0100)]
scsi: qla2xxx: fix spelling mistake "initializatin" -> "initialization"
There is a spelling mistake in a ql_log message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
zhengbin [Thu, 22 Aug 2019 14:20:47 +0000 (22:20 +0800)]
scsi: hisi_sas: remove set but not used variable 'irq_value'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c: In function cq_interrupt_v1_hw:
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c:1542:6: warning: variable irq_value set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sreekanth Reddy [Thu, 22 Aug 2019 06:19:01 +0000 (02:19 -0400)]
scsi: mpt3sas: Introduce module parameter to override queue depth
This patch provides a module parameter and sysfs interface to select
whether the queue depth for each device should be based on the
protocol-specific value set by the driver (the default) or the maximum
supported by the controller (can_queue).
Although we have a sysfs interface per sdev to change the queue depth
of individual scsi devices, this implementation provides a single
sysfs entry per shost to switch between the controller max and the
driver default.
[mkp: tweaked commit desc]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Tue, 20 Aug 2019 02:18:36 +0000 (19:18 -0700)]
scsi: qla2xxx: Fix a recently introduced kernel warning
According to the firmware documentation a status type 0 IOCB can be
followed by one or more status continuation type 0 IOCBs. Hence do not
complain if the completion function is not called from inside the status
type 0 IOCB handler.
WARNING: CPU: 10 PID: 425 at drivers/scsi/qla2xxx/qla_isr.c:2784
qla2x00_status_entry.isra.7+0x484/0x17b0 [qla2xxx]
CPU: 10 PID: 425 Comm: kworker/10:1 Tainted: G E 5.3.0-rc4-next-
20190813-autotest-autotest #1
Workqueue: qla2xxx_wq qla25xx_free_rsp_que [qla2xxx]
Call Trace:
qla2x00_status_entry.isra.7+0x1484/0x17b0 [qla2xxx] (unreliable)
qla24xx_process_response_queue+0x7d8/0xbd0 [qla2xxx]
qla25xx_free_rsp_que+0x1a0/0x220 [qla2xxx]
process_one_work+0x25c/0x520
worker_thread+0x8c/0x5e0
kthread+0x154/0x1a0
ret_from_kernel_thread+0x5c/0x7c
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stanley Chu [Mon, 19 Aug 2019 13:43:28 +0000 (21:43 +0800)]
scsi: ufs: fix broken hba->outstanding_tasks
Currently bits in hba->outstanding_tasks are cleared only after their
corresponding task management commands are successfully done by
__ufshcd_issue_tm_cmd().
If timeout happens in a task management command, its corresponding bit in
hba->outstanding_tasks will not be cleared until next task management
command with the same tag used successfully finishes.
This is wrong and can lead to some issues, like power issue. For example,
ufshcd_release() and ufshcd_gate_work() will do nothing if
hba->outstanding_tasks is not zero even if both UFS host and devices are
actually idle.
Solution is referred from error handling of device commands: bits in
hba->outstanding_tasks shall be cleared regardless of their execution
results.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Thu, 15 Aug 2019 09:14:54 +0000 (10:14 +0100)]
scsi: fcoe: remove redundant call to skb_transport_header
Pointer fh is being assigned a return value from the call to
skb_transport_header however this value is never read and fh is being
re-assigned immediately afterwards with a new value. Since there are
side-effects from calling skb_transport_header the call is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Anil Varughese [Tue, 13 Aug 2019 07:42:50 +0000 (08:42 +0100)]
scsi: ufs: Disable local LCC in .link_startup_notify() in Cadence UFS
Some UFS devices have issues if LCC is enabled. So we are setting
PA_LOCAL_TX_LCC_Enable to 0 before link startup which will make sure that
both host and device TX LCC are disabled once link startup is completed.
Signed-off-by: Anil Varughese <aniljoy@cadence.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Wed, 31 Jul 2019 22:11:52 +0000 (23:11 +0100)]
scsi: bfa: remove redundant assignment to variable error
Variable error is being initialized with a value that is never read and
error is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:57:12 +0000 (16:57 -0700)]
scsi: lpfc: Update lpfc version to 12.4.0.0
Update lpfc version to 12.4.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:57:11 +0000 (16:57 -0700)]
scsi: lpfc: Merge per-protocol WQ/CQ pairs into single per-cpu pair
Currently, each hardware queue, typically allocated per-cpu, consists of a
WQ/CQ pair per protocol. Meaning if both SCSI and NVMe are supported 2
WQ/CQ pairs will exist for the hardware queue. Separate queues are
unnecessary. The current implementation wastes memory backing the 2nd set
of queues, and the use of double the SLI-4 WQ/CQ's means less hardware
queues can be supported which means there may not always be enough to have
a pair per cpu. If there is only 1 pair per cpu, more cpu's may get their
own WQ/CQ.
Rework the implementation to use a single WQ/CQ pair by both protocols.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:57:10 +0000 (16:57 -0700)]
scsi: lpfc: Add NVMe sequence level error recovery support
FC-NVMe-2 added support for sequence level error recovery in the FC-NVME
protocol. This allows for the detection of errors and lost frames and
immediate retransmission of data to avoid exchange termination, which
escalates into NVMeoFC connection and association failures. A significant
RAS improvement.
The driver is modified to indicate support for SLER in the NVMe PRLI is
issues and to check for support in the PRLI response. When both sides
support it, the driver will set a bit in the WQE to enable the recovery
behavior on the exchange. The adapter will take care of all detection and
retransmission.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:57:09 +0000 (16:57 -0700)]
scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.
Typical SLI-4 hardware supports up to 2 4KB pages to be registered per XRI
to contain the exchanges Scatter/Gather List. This caps the number of SGL
elements that can be in the SGL. There are not extensions to extend the
list out of the 2 pages.
The G7 hardware adds a SGE type that allows the SGL to be vectored to a
different scatter/gather list segment. And that segment can contain a SGE
to go to another segment and so on. The initial segment must still be
pre-registered for the XRI, but it can be a much smaller amount (256Bytes)
as it can now be dynamically grown. This much smaller allocation can
handle the SG list for most normal I/O, and the dynamic aspect allows it to
support many MB's if needed.
The implementation creates a pool which contains "segments" and which is
initially sized to hold the initial small segment per xri. If an I/O
requires additional segments, they are allocated from the pool. If the
pool has no more segments, the pool is grown based on what is now
needed. After the I/O completes, the additional segments are returned to
the pool for use by other I/Os. Once allocated, the additional segments are
not released under the assumption of "if needed once, it will be needed
again". Pools are kept on a per-hardware queue basis, which is typically
1:1 per cpu, but may be shared by multiple cpus.
The switch to the smaller initial allocation significantly reduces the
memory footprint of the driver (which only grows if large ios are
issued). Based on the several K of XRIs for the adapter, the 8KB->256B
reduction can conserve 32MBs or more.
It has been observed with per-cpu resource pools that allocating a resource
on CPU A, may be put back on CPU B. While the get routines are distributed
evenly, only a limited subset of CPUs may be handling the put routines.
This can put a strain on the lpfc_put_cmd_rsp_buf_per_cpu routine because
all the resources are being put on a limited subset of CPUs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:57:08 +0000 (16:57 -0700)]
scsi: lpfc: Add MDS driver loopback diagnostics support
Added code to support driver loopback with MDS Diagnostics. This style of
diagnostics passes frames from the fabric to the driver who then echo them
back out the link. SEND_FRAME WQEs are used to transmit the frames. Added
the SOF and EOF field location definitions for use by SEND_FRAME.
Also ensure that enable_mds_diags is a RW parameter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:57:07 +0000 (16:57 -0700)]
scsi: lpfc: Add first and second level hardware revisions to sysfs reporting
To aid better hardware detection when there are issues, report the first
and second level hardware revisions from the READ_REV command. Add the
elements to the existing hardware id string.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:57:06 +0000 (16:57 -0700)]
scsi: lpfc: Migrate to %px and %pf in kernel print calls
In order to see real addresses, convert %p with %px for kernel addresses
and replace %p with %pf for functions.
While converting, standardize on "x%px" throughout (not %px or 0x%px).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:57:05 +0000 (16:57 -0700)]
scsi: lpfc: Add simple unlikely optimizations to reduce NVME latency
While performing code review, several relatively simple optimizations can
be done in the fast path.
Add these optimizations (unlikely designators).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:57:04 +0000 (16:57 -0700)]
scsi: lpfc: Fix coverity warnings
Running on Coverity produced the following errors:
- coding style (indentation)
- memset size mismatch errors
note: comment cases where it is purposely a mismatch
Fix the errors.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:57:03 +0000 (16:57 -0700)]
scsi: lpfc: Fix nvme first burst module parameter description
modinfo for lpfc_nvme_enable_fb is incorrect. FirstBurst on lpfc target is
not fully supported.
Update the attribute description
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:57:02 +0000 (16:57 -0700)]
scsi: lpfc: Fix BlockGuard enablement on FCoE adapters
The driver is allowing the user to change lpfc_enable_bg while loading the
driver against a FCoE adapter. This is not supported.
No check is made for the adapter type when applying the blockguard
enablement value.
Fix by verifying the adapter type before setting the enablement flag.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:57:01 +0000 (16:57 -0700)]
scsi: lpfc: Fix reported physical link speed on a disabled trunked link
GetTrunkInfo is displaying an incorrect link speed when the link is a trunk
and the link has gone down. The driver is not clearing the logical speed
as part of the link down transition.
Fix by setting the logical speed to UNKNOWN SPEED when the link goes down.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:57:00 +0000 (16:57 -0700)]
scsi: lpfc: Fix Max Frame Size value shown in fdmishow output
Max Frame Size value is shown as 34816 in fdmishow from Switch.
The driver uses bbRcvSize in common service param which is obtained from
the READ_SPARM mailbox command. The bbRcvSize field which is displayed is a
three nibble field but the driver is printing a full four nibbles.
Fix by masking off the upper nibble.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:59 +0000 (16:56 -0700)]
scsi: lpfc: Fix upcall to bsg done in non-success cases
The scsi transport fc bsg interface does not expect the bsg_job_done()
callback to be done if the bsg request call returns failure. Several of the
HST_VENDOR cases in the driver unconditionally call bsg_job_done()
regardless of the returning value.
Fix the code to only call bsg_job_done() if the call to lpfc_bsg_request()
will return success.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:58 +0000 (16:56 -0700)]
scsi: lpfc: Fix sli4 adapter initialization with MSI
When forcing the use of MSI (vs MSI-X) the driver is crashing in
pci_irq_get_affinity.
The driver was not using the new pci_alloc_irq_vectors interface in the MSI
path.
Fix by using pci_alloc_irq_vectors() with PCI_RQ_MSI in the MSI path.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:57 +0000 (16:56 -0700)]
scsi: lpfc: Fix nvme sg_seg_cnt display if HBA does not support NVME
The driver is currently reporting a non-zero nvme sg_seg_cnt value of 256
when nvme is disabled. It should be zero.
Fix by ensuring the value is cleared.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:56 +0000 (16:56 -0700)]
scsi: lpfc: Fix nvme target mode ABTSing a received ABTS
If an unsolicited ABTS was received, the driver looks up the exchange it
references. It it does various searches looking for the exchange
context. When one is eventually matched and it is associated with an XRI
context, the driver sends an ABORT WQE to terminate the exchange. Current
code looks at whether the transport had taken action on the XRI yet or not
(no action if set to LPFC_NVMET_STE_RCV; action if non-LPFC_NVMET_STE_RCV).
Based on action or not one of two (sol vs unsol) issue abort routines are
called. The unsol version cheats and transmits a sequence containing an
ABTS with no interaction with the adapter. The sol version issues an Abort
WQE and lets the adapter manage whether the ABTS is sent to not.
The issue is the unsol version is sending ABTS unconditionally for the
exchange that received the ABTS. It's unnecessary.
Remove the conditional and just call the adapter command-based routine to
let the adapter manage the ABTS.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:55 +0000 (16:56 -0700)]
scsi: lpfc: Fix hang when downloading fw on port enabled for nvme
As part of firmware download, the adapter is reset. On the adapter the
reset causes the function to stop and all outstanding io is terminated
(without responses). The reset path then starts teardown of the adapter,
starting with deregistration of the remote ports with the nvme-fc
transport. The local port is then deregistered and the driver waits for
local port deregistration. This never finishes.
The remote port deregistrations terminated the nvme controllers, causing
them to send aborts for all the outstanding io. The aborts were serviced in
the driver, but stalled due to its state. The nvme layer then stops to
reclaim it's outstanding io before continuing. The io must be returned
before the reset on the controller is deemed complete and the controller
delete performed. The remote port deregistration won't complete until all
the controllers are terminated. And the local port deregistration won't
complete until all controllers and remote ports are terminated. Thus things
hang.
The issue is the reset which stopped the adapter also stopped all the
responses that would drive i/o completions, and the aborts were also
stopped that stopped i/o completions. The driver, when resetting the
adapter like this, needs to be generating the completions as part of the
adapter reset so that I/O complete (in error), and any aborts are not
queued.
Fix by adding flush routines whenever the adapter port has been reset or
discovered in error. The flush routines will generate the completions for
the scsi and nvme outstanding io. The abort ios, if waiting, will be caught
and flushed as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:54 +0000 (16:56 -0700)]
scsi: lpfc: Fix too many sg segments spamming in kernel log
This issue is specific to SLI-3 adapters, specifically when DIF is used.
Once seen, this message floods the logs:
9064 BLKGRD: lpfc_scsi_prep_dma_buf_s3: Too many sg segments from
dma_map_sg
The driver, upon detecting an error such as too many elements in an sglist,
misrepresents the error by treating it as a temporary resource issue by
returning MLQUEUE_HOST_BUSY. In these cases, no retry will fix it and it
should have been a hard error. The repeated retry was causing the spamming
of the log.
As for the initial reason of why an I/O encountered this issue at all is
not clear as parameters set by the driver should have avoided this. The
dm multipath maintainer has been notified of the issue.
Fix by changing the return code for the dma mapping routines to indicate
cases that are not retryable and return DID_ERROR on those cases.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:53 +0000 (16:56 -0700)]
scsi: lpfc: Fix crash due to port reset racing vs adapter error handling
If the adapter encounters a condition which causes the adapter to fail
(driver must detect the failure) simultaneously to a request to the driver
to reset the adapter (such as a host_reset), the reset path will be racing
with the asynchronously-detect adapter failure path. In the failing
situation, one path has started to tear down the adapter data structures
(io_wq's) while the other path has initiated a repeat of the teardown and
is in the lpfc_sli_flush_xxx_rings path and attempting to access the
just-freed data structures.
Fix by the following:
- In cases where an adapter failure is detected, rather than explicitly
calling offline_eratt() to start the teardown, change the adapter state
and let the later calls of posted work to the slowpath thread invoke the
adapter recovery. In essence, this means all requests to reset are
serialized on the slowpath thread.
- Clean up the routine that restarts the adapter. If there is a failure
from brdreset, don't immediately error and leave things in a partial
state. Instead, ensure the adapter state is set and finish the teardown
of structures before returning.
- If in the scsi host reset handler and the board fails to reset and
restart (which can be due to parallel reset/recovery paths), instead of
hard failing and explicitly calling offline_eratt() (which gets into the
redundant path), just fail out and let the asynchronous path resolve the
adapter state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:52 +0000 (16:56 -0700)]
scsi: lpfc: Fix deadlock on host_lock during cable pulls
During cable pull testing a deadlock was seen between lpfc_nlp_counters()
vs lpfc_mbox_process_link_up() vs lpfc_work_list_done(). They are all
waiting on the shost->host_lock.
Issue is all of these cases raise irq when taking out the lock but use
spin_unlock_irq() when unlocking. The unlock path is will unconditionally
re-enable interrupts in cases where irq state should be preserved. The
re-enablement allowed the other paths to execute which then causes the
deadlock.
Fix by converting the lock/unlock to irqsave/irqrestore.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:51 +0000 (16:56 -0700)]
scsi: lpfc: Fix error in remote port address change
In a test with high nvme remote port counts connected via a multi-hop FC
switch config where switches were systematically reset (e.g. fabric
partitioning and re-establishment), the nvme remote ports would switch
addresses based on the switch reconfiguration events. The driver would get
into a situation where the nvme port changed address, PLOGI and PRLI would
succeed nvme transport registration occurred, but subsequent LS requests by
the nvme subsystem failed due to a bad ndlp state and connectivity to the
device failed.
The driver hit a race condition on multiple devices that address swapped
simultaneously. In cases where the driver notices the remote port structure
came back as the same value as previously (meaning a nvme_rport structure
was re-enabled and did not go through devloss_tmo/connect_tmo_failures on
all controllers) the driver would unconditionally exit assuming the ndlp
information was correct. But, if the ndlp's had been swapped, the ndlp had
stale port state information, which when used by the LS request commands,
would fail the commands.
Fix by checking whether a node swap had occurred, and only exit if no ndlp
swap had occurred.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:50 +0000 (16:56 -0700)]
scsi: lpfc: Fix driver nvme rescan logging
In situations where zoning is not being used, thus NVMe initiators see
other NVMe initiators as well as NVMe targets, a link bounce on an
initiator will cause the NVMe initiators to spew "6169" State Error
messages.
The driver is not qualifying whether the remote port is a NVMe targer or
not before calling the lpfc_nvme_rescan_port(), which validates the role
and prints the message if its only an NVMe initiator.
Fix by the following:
- Before calling lpfc_nvme_rescan_port() ensure that the node is a NVMe
storage target or a NVMe discovery controller.
- Clean up implementation of lpfc_nvme_rescan_port. remoteport pointer
will always be NULL if a NVMe initiator only. But, grabbing of
remoteport pointer should be done under lock to coincide with the
registering of the remote port with the fc transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:49 +0000 (16:56 -0700)]
scsi: lpfc: Fix sg_seg_cnt for HBAs that don't support NVME
On an SLI-3 adapter which does not support NVMe, but with the driver global
attribute to enable nvme on any adapter if it does support NVMe
(e.g. module parameter lpfc_enable_fc4_type=3), the SGL and total SGE
values are being munged by the protocol enablement when it shouldn't be.
Correct by changing the location of where the NVME sgl information is being
applied, which will avoid any SLI-3-based adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:48 +0000 (16:56 -0700)]
scsi: lpfc: Fix propagation of devloss_tmo setting to nvme transport
If admin changes the devloss_tmo on an rport via the fc_remote_port rport
dev_loss_tmo attribute, the value is on set on scsi stack. The change is
not propagated to NVMe.
The set routine in the lldd lacks the call to
nvme_fc_set_remoteport_devloss() to set the value.
Fix by adding the call to the lldd set routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:47 +0000 (16:56 -0700)]
scsi: lpfc: Fix loss of remote port after devloss due to lack of RPIs
In tests with remote ports contantly logging out/logging coupled with
occassional local link bounce, if a remote port is disocnnected for longer
than devloss_tmo and then subsequently reconnected, eventually the test
will fail to login with the remote port and remote port connectivity is
lost.
When devloss_tmo expires, the driver does not free the node struct until
the port or npiv instances is being deleted. The node is left allocated but
the state set to UNUSED. If the node was in the process of logging in when
the local link drop occurred, meaning the RPI was allocated for the node in
order to send the ELS, but not yet registered which comes after successful
login, the node is moved to the NPR state, and if devloss expires, to
UNUSED state. If the remote port comes back, the node associated with it
is restarted and this path happens to allocate a new RPI and overwrites the
prior RPI value. In the cases where the port was logged in and loggs out,
the path did release the RPI but did not set the node rpi value. In the
cases where the remote port never finished logging in, the path never did
the call to release the rpi. In this latter case, when the node is
subsequently restore, the new rpi allocation overwrites the rpi that was
not released, and the rpi is now leaked. Eventually the port will run out
of RPI resources to log into new remote ports.
Fix by following changes:
- When an rpi is released, do so under locks and ensure the node rpi value
is set to a non-allocated value (LPFC_RPI_ALLOC_ERROR). Note:
refactored to a small service routine to avoid indentation issues.
- When re-enabling a node, check the rpi value to determine if a new
allocation is necessary. If already set, use the prior rpi.
Enhanced logging to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:46 +0000 (16:56 -0700)]
scsi: lpfc: Fix devices that don't return after devloss followed by rediscovery
If a remote port is removed and remains removed for devloss_tmo, if an RSCN
is subsequently received indicating the presence of the remte port, the
driver does not login to and rediscovery the remote port.
Currently, in order to for a port to be rediscovered post an RSCN, the node
state must be NPR to reflect not logged in. When devloss expires, the node
state is marked UNUSED. When an RSCN occurs, the nodes referenced by the
RSCN will have a NPR_2B_DISC flag set, but the re-login will only be
attempted if the node is in NPR_NODE state. Thus the node is skipped over.
Fix by recognizing the NPR_2B_DISC and UNUSED and transition the node back
to NPR state to allow the re-login to take place.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:45 +0000 (16:56 -0700)]
scsi: lpfc: Fix null ptr oops updating lpfc_devloss_tmo via sysfs attribute
If an admin updates lpfc's devloss_tmo sysfs attribute, the kernel will
oops.
Coding of a loop allowed a new value (rport) to be set/checked for null
followed by an older value (remoteport) checked for null to allow progress
where the new value, even though null, will be referenced.
Rework the logic to validate and prevent any reference to the null ptr.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:44 +0000 (16:56 -0700)]
scsi: lpfc: Fix FLOGI handling across multiple link up/down conditions
It's possible for the driver to initiate an FLOGI and before it completes,
another link down/up transition occurs requiring a new FLOGI. Currently,
nothing is done to abort/noop the older FLOGI request to the adapter, so if
this transition occurs and the FLOGI completion is received after the link
down/up transition, the driver may erroneously act on the older FLOGI. In
most cases, the adapter properly terminates/fails the FLOGI, but there is a
timing condition where the FLOGI may complete on the wire prior to the
transition, but the response may not be seen/processed by the driver before
the driver sees the link transition.
Fix by having the link down handler in the driver run through any
outstanding ELS's and change the completion handler of the ELS so that it
will be no-op'd and released.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:43 +0000 (16:56 -0700)]
scsi: lpfc: Fix oops when fewer hdwqs than cpus
When tearing down the adapter for a reset, online/offline, or driver
unload, the queue free routine would hit a GPF oops. This only occurs on
conditions where the number of hardware queues created is fewer than the
number of cpus in the system. In this condition cpus share a hardware
queue. And of course, it's the 2nd cpu that shares a hardware that
attempted to free it a second time and hit the oops.
Fix by reworking the cpu to hardware queue mapping such that:
Assignment of hardware queues to cpus occur in two passes:
first pass: is first time assignment of a hardware queue to a cpu.
This will set the LPFC_CPU_FIRST_IRQ flag for the cpu.
second pass: for cpus that did not get a hardware queue they will
be assigned one from a primary cpu (one set in first pass).
Deletion of hardware queues is driven by cpu itteration, and queues
will only be deleted if the LPFC_CPU_FIRST_IRQ flag is set.
Also contains a few small cleanup fixes and a little better logging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:42 +0000 (16:56 -0700)]
scsi: lpfc: Fix irq raising in lpfc_sli_hba_down
The adapter reset path (lpfc_sli_hba_down) is taking/releasing a lock with
irq. But, the path is already under the hbalock which raised irq so it's
unnecessary.
Convert to simple lock/unlock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:41 +0000 (16:56 -0700)]
scsi: lpfc: Fix Oops in nvme_register with target logout/login
lpfc_nvme_register_port hit a null prev_ndlp pointer in a test with lots of
target ports swapping addresses. The oldport value was stale, thus it's
ndlp (prev_ndlp set to it) was used.
Fix by moving oldrport pointer checks, and if used prev_ndlp pointer
assignment, to be done while the lock is held.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:40 +0000 (16:56 -0700)]
scsi: lpfc: Fix issuing init_vpi mbox on SLI-3 card
The driver is inadvertently trying to issue an INIT_VPI mailbox command on
an SLI-3 driver. The command is specific to SLI-4. When the call is made to
send the command, if on an SLI-3 adapter, an array pointer is NULL and the
driver will oops.
Fix by restricting the command to SLI-4 adapters only.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:39 +0000 (16:56 -0700)]
scsi: lpfc: Fix ADISC reception terminating login state if a NVME target
If a target issues an ADISC to the port and the target is a NVME target,
the driver is inadvertantly invalidating the login and marking the remote
port as logged out. Communication with the target is lost.
Revise the ADISC check so that FCP or NVME targets will be marked valid at
the end of ADISC processing. Enhance logging to recognize condition
better.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:38 +0000 (16:56 -0700)]
scsi: lpfc: Fix discovery when target has no GID_FT information
Some remote ports may be slow in registering their GID_FT protocol
information with the fabric. If the remote port is an initiator, it may
send PLOGI to the port before the GID_FT logic is complete. Meaning, after
accepting the PLOGI, when the driver may see no response to the GID_FT that
is issued after the login to determine the protocols supported so that
proper PRLI's may be transmit. If the driver has no fc4 information, it
currently stops and the remote port is not discovered.
Fix by issuing a LOGO when there is no GID_FT information. The LOGO
completion handling will attempt to re-login if the nport_id is still
present.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:37 +0000 (16:56 -0700)]
scsi: lpfc: Fix port relogin failure due to GID_FT interaction
In cases of remote-port-side cable pull/replug, there happens to be a
target that upon replug will send the port a PLOGI, a PRLI, and a LOGO.
When this sequence is received by the driver, the PLOGI accepted and a
GFT_ID is issued to find the protocol support for the remote port. While
the GFT_ID is outstanding, a LOGO is received. The driver logs the remote
port out and unregisters the RPI and schedules a new PLOGI transmission.
However, the GFT_ID was not terminated. When it completed, the driver
attempted to transition the remote port to PRLI transmission, which cancels
the PLOGI scheduling. The PRLI transmit attempt is rejected by the adapter
as the remote port is not logged in. No retry is attempted as it's expected
the logout is noted and the supposedly scheduled PLOGI should address the
state. As there is no PLOGI, the remote port does not get re-discovered.
Fix by aborting the outstanding GFT_ID if the related remote port is logged
out.
Ensure a PRLI transmit attempt only occurs if the remote port is logging
in. This avoids the incorrect attempt while logged out.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:36 +0000 (16:56 -0700)]
scsi: lpfc: Fix leak of ELS completions on adapter reset
If the adapter is reset while there are outstanding ELS's, subsequent
reinitialization of the adapter will fail as it has not recovered all of
the io contexts relative to the ELS's.
If an ELS timed out or otherwise failed and an the ELS was attempted to be
aborted (which changes the ELS completion context), in causes where the
driver generates completions for the outstanding IO as the adapter would
not due to being reset, the driver released only the ELS context and failed
to release the abort context. When the adapter went to reinit, as it had
not received all of the contexts, it failed to reinit.
Fix by having the ELS completion handler identify the driver-generated
completion status and release the abort context.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:35 +0000 (16:56 -0700)]
scsi: lpfc: Fix failure to clear non-zero eq_delay after io rate reduction
Unusually high IO latency can be observed with little IO in progress. The
latency may remain high regardless of amount of IO and can only be cleared
by forcing lpfc_fcp_imax values to non-zero and then back to zero.
The driver's eq_delay mechanism that scales the interrupt coalescing based
on io completion load failed to reduce or turn off coalescing when load
decreased. Specifically, if no io completed on a cpu within an eq_delay
polling window, the eq delay processing was skipped and no change was made
to the coalescing values. This left the coalescing values set when they
were no longer applicable.
Fix by always clearing the percpu counters for each time period and always
run the eq_delay calculations if an eq has a non-zero coalescing value.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:34 +0000 (16:56 -0700)]
scsi: lpfc: Fix crash on driver unload in wq free
If a timer routine uses workqueues, it could fire before the workqueue is
allocated.
Fix by allocating the workqueue before the timer routines are setup
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:33 +0000 (16:56 -0700)]
scsi: lpfc: Fix ELS field alignments
After seeing some interoperability issues with ADISC, it was determined the
ELS definitions in lpfc were using types that allowed the compiler to add
pad to the structure, causing the structure to no longer be per spec. The
offending structures are ADISC, FAN, and RNID.
This patch implements the simple fix of eliminating the pad by forcing the
compiler to pack the structure. Care was taken to ensure field accesses
won't be by operations that would hit a bad field alignment.
The better solution would be to convert to the uapi fc header definitions,
but the number of changes required to do is rather intrusive so this course
of action was deferred.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:32 +0000 (16:56 -0700)]
scsi: lpfc: Fix PLOGI failure with high remoteport count
When connected to a high number of remote ports, the driver is encountering
PLOGI errors. The errors are due to adapter detected failures indicating
illegal field values.
Turns out the driver was prematurely clearing an RPI bitmask before waiting
for an UNREG_RPI mailbox completion. This allowed the RPI to be reused
before it was actually available.
Fix by clearing RPI bitmask only after UNREG_RPI mailbox completion.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 14 Aug 2019 23:56:31 +0000 (16:56 -0700)]
scsi: lpfc: Limit xri count for kdump environment
scsi-mq operation inherently performs pre-allocation of resources for
blk-mq request queues. Even though the kdump environment reduces the
configuration to a single CPU, thus 1 hardware queue, which helps
significantly, the resources are still rather large due to the per request
allocations. blk-mq pre-allocations can be over 4KB per request. With
adapter can_queue values in the 4k or 8k range, this can easily be 32MBs
before any other driver memory is factored in. Driver SGL DMA buffer
allocation can be up to 8KB per request as well adding an additional
64MB. Totals are well over 100MB for a single shost. Given kdump memory
auto-sizing utilities don't accommodate this amount of memory well, it's
very possible for kdump to fail due to lack of memory.
Fix by having the driver recognize that it is booting within a kdump
context and reduce the number of requests it will support to a more
reasonable value.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hariprasad Kelam [Sun, 21 Jul 2019 11:42:29 +0000 (17:12 +0530)]
scsi: lpfc: remove NULL check before some freeing functions
As dma_pool_destroy and mempool_destroy functions has NULL check. We may
not need NULL check before calling them.
Fix below warnings reported by coccicheck
./drivers/scsi/lpfc/lpfc_mem.c:252:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:255:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:258:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:261:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:265:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:269:2-17: WARNING: NULL check before some
freeing functions is not needed.
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nishka Dasgupta [Mon, 19 Aug 2019 07:55:57 +0000 (13:25 +0530)]
scsi: ufs-qcom: Make structure ufs_hba_qcom_vops constant
Static structure ufs_hba_qcom_vops, of type ufs_hba_variant_ops, is used
only once, when it is passed as the second argument to function
ufshcd_pltfrm_init(). In the definition of ufshcd_pltfrm_init(), its second
parameter (corresponding to ufs_hba_qcom_vops) is declared as
constant. Hence declare ufs_hba_qcom_vops itself constant as well to
protect it from unintended modification. Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fuqian Huang [Mon, 12 Aug 2019 08:31:34 +0000 (16:31 +0800)]
scsi: lpfc: use spin_lock_irqsave in IRQ context
As spin_unlock_irq will enable interrupts.
Function lpfc_findnode_rpi is called from
lpfc_sli_abts_err_handler (./drivers/scsi/lpfc/lpfc_sli.c)
<- lpfc_sli_async_event_handler
<- lpfc_sli_process_unsol_iocb
<- lpfc_sli_handle_fast_ring_event
<- lpfc_sli_fp_intr_handler
<- lpfc_sli_intr_handler
and lpfc_sli_intr_handler is an interrupt handler.
Interrupts are enabled in interrupt handler. Use
spin_lock_irqsave/spin_unlock_irqrestore instead of spin_(un)lock_irq in
IRQ context to avoid this.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fuqian Huang [Thu, 8 Aug 2019 01:35:25 +0000 (09:35 +0800)]
scsi: lpfc: remove redundant code
Remove the redundant initialization code.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Tue, 13 Aug 2019 13:23:49 +0000 (14:23 +0100)]
scsi: fnic: remove redundant assignment of variable rc
Variable ret is initialized to a value that is never read and it is
re-assigned later and immediately returns. Clean up the code by removing
rc and just returning 0.
[mkp: typo]
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Martin Wilck [Wed, 14 Aug 2019 13:28:29 +0000 (13:28 +0000)]
scsi: qla2xxx: cleanup trace buffer initialization
Avoid code duplication between qla2x00_alloc_offload_mem() and
qla2x00_alloc_fw_dump() by moving the FCE and EFT buffer allocation and
initialization to separate functions. Cleanly track failure and success by
making sure that the ha->eft, ha->fce and respective eft_dma, fce_dma
members are set if and only if the buffers are properly allocated and
initialized. Avoid pointless buffer reallocation. Eliminate some goto
statements. Make sure the fce_enabled flag is cleared when the FCE buffer
is freed.
Fixes:
ad0a0b01f088 ("scsi: qla2xxx: Fix Firmware dump size for Extended login and Exchange Offload")
Fixes:
a28d9e4ef997 ("scsi: qla2xxx: Add support for multiple fwdump templates/segments")
Cc: Joe Carnuccio <joe.carnuccio@cavium.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Martin Wilck [Wed, 14 Aug 2019 13:28:27 +0000 (13:28 +0000)]
scsi: qla2xxx: qla2x00_alloc_fw_dump: set ha->eft
In qla2x00_alloc_fw_dump(), an existing EFT buffer (e.g. from previous
invocation of qla2x00_alloc_offload_mem()) is freed. The buffer is then
re-allocated, but without setting the eft and eft_dma fields to the new
values.
Fixes:
a28d9e4ef997 ("scsi: qla2xxx: Add support for multiple fwdump templates/segments")
Cc: Joe Carnuccio <joe.carnuccio@cavium.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Masahiro Yamada [Sun, 21 Jul 2019 14:25:02 +0000 (23:25 +0900)]
scsi: use __u{8,16,32,64} instead of uint{8,16,32,64}_t in uapi headers
When CONFIG_UAPI_HEADER_TEST=y, exported headers are compile-tested to make
sure they can be included from user-space.
Currently, scsi_bsg_fc.h, scsi_netlink.h, and scsi_netlink_fc.h are
excluded from the test coverage. To make them join the compile-test, we
need to fix the build errors attached below.
For a case like this, we decided to use __u{8,16,32,64} variable types in
this discussion:
https://lkml.org/lkml/2019/6/5/18
Build log:
CC usr/include/scsi/scsi_netlink_fc.h.s
CC usr/include/scsi/scsi_netlink.h.s
CC usr/include/scsi/scsi_bsg_fc.h.s
In file included from ./usr/include/scsi/scsi_netlink_fc.h:10:0,
from <command-line>:32:
./usr/include/scsi/scsi_netlink.h:29:2: error: unknown type name uint8_t
uint8_t version;
^~~~~~~
./usr/include/scsi/scsi_netlink.h:30:2: error: unknown type name uint8_t
uint8_t transport;
^~~~~~~
./usr/include/scsi/scsi_netlink.h:31:2: error: unknown type name uint16_t
uint16_t magic;
^~~~~~~~
./usr/include/scsi/scsi_netlink.h:32:2: error: unknown type name uint16_t
uint16_t msgtype;
^~~~~~~~
CC usr/include/rdma/vmw_pvrdma-abi.h.s
./usr/include/scsi/scsi_netlink.h:33:2: error: unknown type name uint16_t
uint16_t msglen;
^~~~~~~~
./usr/include/scsi/scsi_netlink.h:34:33: error: uint64_t undeclared here (not in a function); did you mean __uint128_t ?
} __attribute__((aligned(sizeof(uint64_t))));
^~~~~~~~
__uint128_t
./usr/include/scsi/scsi_netlink.h:78:2: error: expected specifier-qualifier-list before uint64_t
uint64_t vendor_id;
^~~~~~~~
In file included from <command-line>:32:0:
./usr/include/scsi/scsi_netlink_fc.h:46:2: error: expected specifier-qualifier-list before uint64_t
uint64_t seconds;
^~~~~~~~
make[2]: *** [scripts/Makefile.build;302: usr/include/scsi/scsi_netlink_fc.h.s] Error 1
make[2]: *** Waiting for unfinished jobs....
In file included from <command-line>:32:0:
./usr/include/scsi/scsi_netlink.h:29:2: error: unknown type name uint8_t
uint8_t version;
^~~~~~~
./usr/include/scsi/scsi_netlink.h:30:2: error: unknown type name uint8_t
uint8_t transport;
^~~~~~~
./usr/include/scsi/scsi_netlink.h:31:2: error: unknown type name uint16_t
uint16_t magic;
^~~~~~~~
./usr/include/scsi/scsi_netlink.h:32:2: error: unknown type name uint16_t
uint16_t msgtype;
^~~~~~~~
./usr/include/scsi/scsi_netlink.h:33:2: error: unknown type name uint16_t
uint16_t msglen;
^~~~~~~~
./usr/include/scsi/scsi_netlink.h:34:33: error: uint64_t undeclared here (not in a function); did you mean __uint128_t ?
} __attribute__((aligned(sizeof(uint64_t))));
^~~~~~~~
__uint128_t
./usr/include/scsi/scsi_netlink.h:78:2: error: expected specifier-qualifier-list before uint64_t
uint64_t vendor_id;
^~~~~~~~
make[2]: *** [scripts/Makefile.build;302: usr/include/scsi/scsi_netlink.h.s] Error 1
In file included from <command-line>:32:0:
./usr/include/scsi/scsi_bsg_fc.h:69:2: error: unknown type name uint8_t
uint8_t reserved;
^~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:72:2: error: unknown type name uint8_t
uint8_t port_id[3];
^~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:90:2: error: unknown type name uint8_t
uint8_t reserved;
^~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:93:2: error: unknown type name uint8_t
uint8_t port_id[3];
^~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:114:2: error: unknown type name uint8_t
uint8_t command_code;
^~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:117:2: error: unknown type name uint8_t
uint8_t port_id[3];
^~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:154:2: error: unknown type name uint32_t
uint32_t status; /* See FC_CTELS_STATUS_xxx */
^~~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:158:3: error: unknown type name uint8_t
uint8_t action; /* fragment_id for CT REJECT */
^~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:159:3: error: unknown type name uint8_t
uint8_t reason_code;
^~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:160:3: error: unknown type name uint8_t
uint8_t reason_explanation;
^~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:161:3: error: unknown type name uint8_t
uint8_t vendor_unique;
^~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:177:2: error: unknown type name uint8_t
uint8_t reserved;
^~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:180:2: error: unknown type name uint8_t
uint8_t port_id[3];
^~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:185:2: error: unknown type name uint32_t
uint32_t preamble_word0; /* revision & IN_ID */
^~~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:186:2: error: unknown type name uint32_t
uint32_t preamble_word1; /* GS_Type, GS_SubType, Options, Rsvd */
^~~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:187:2: error: unknown type name uint32_t
uint32_t preamble_word2; /* Cmd Code, Max Size */
^~~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:207:2: error: unknown type name uint64_t
uint64_t vendor_id;
^~~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:210:2: error: unknown type name uint32_t
uint32_t vendor_cmd[0];
^~~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:217:2: error: unknown type name uint32_t
uint32_t vendor_rsp[0];
^~~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:236:2: error: unknown type name uint8_t
uint8_t els_code;
^~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:254:2: error: unknown type name uint32_t
uint32_t preamble_word0; /* revision & IN_ID */
^~~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:255:2: error: unknown type name uint32_t
uint32_t preamble_word1; /* GS_Type, GS_SubType, Options, Rsvd */
^~~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:256:2: error: unknown type name uint32_t
uint32_t preamble_word2; /* Cmd Code, Max Size */
^~~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:268:2: error: unknown type name uint32_t
uint32_t msgcode;
^~~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:292:2: error: unknown type name uint32_t
uint32_t result;
^~~~~~~~
./usr/include/scsi/scsi_bsg_fc.h:295:2: error: unknown type name uint32_t
uint32_t reply_payload_rcv_len;
^~~~~~~~
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Frederick Lawler [Thu, 18 Jul 2019 02:07:44 +0000 (21:07 -0500)]
scsi: esas2r: Prefer pcie_capability_read_word()
Commit
8c0d3a02c130 ("PCI: Add accessors for PCI Express Capability") added
accessors for the PCI Express Capability so that drivers didn't need to be
aware of differences between v1 and v2 of the PCI Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Frederick Lawler [Thu, 18 Jul 2019 02:07:43 +0000 (21:07 -0500)]
scsi: csiostor: Prefer pcie_capability_read_word()
Commit
8c0d3a02c130 ("PCI: Add accessors for PCI Express Capability") added
accessors for the PCI Express Capability so that drivers didn't need to be
aware of differences between v1 and v2 of the PCI Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Fri, 9 Aug 2019 17:59:32 +0000 (18:59 +0100)]
scsi: sym53c8xx_2: remove redundant assignment to retv
Variable retv is initialized to a value that is never read and it is
re-assigned later. The initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>