OSDN Git Service
Vasanthakumar Thiagarajan [Thu, 5 Nov 2015 06:04:00 +0000 (11:34 +0530)]
ath10k: fix peerid configuration in htt tx desc for htt version < 3.4
Of a word in struct htt_data_tx_desc htt version >= 3.4 firmware uses
LSB 16-bit for frequency configuration which is used for offchannel tx
and MSB 16-bit is for peerid. But other firmwares using version 2.X
(10.1, 10.2.2, 10.2.4 and 10.4) are using 32-bit for peerid in htt tx
desc. So far no issue is found with the existing code setting peerid and
freq for HTT version 2.X, this could be mainly because of 0 as frequecy
(home channel) is being always passed with those firmwares. There may be
issues when non-zero freq is passed with firmware using < 3.4 htt version.
To be safe use target_version_major and target_version_minor along with
htt-op-version before configuring peer id and freq in htt tx desc. This
patch extends ath10k_mac_tx_frm_has_freq() to check for htt_op_version_tlv
and uses the helper while setting peerid in htt_tx_desc.
Fixes:
8d6d36243610 ("ath10k: fix offchan reliability")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vasanthakumar Thiagarajan [Thu, 5 Nov 2015 06:03:59 +0000 (11:33 +0530)]
ath10k: rename the helper which is used for off-channel tx
Rename ath10k_mac_need_offchan_tx_work() to ath10k_mac_tx_frm_has_freq()
to make it more meaningful. This helper will be used in the future
change. No functionality change.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vasanthakumar Thiagarajan [Thu, 5 Nov 2015 06:03:58 +0000 (11:33 +0530)]
ath10k: fix peer assoc complete WMI command for 10.4
There is an extra 4-byte member when compared to WMI 10.2 added to
assoc complete command in WMI 10.4. This new member is used for 160Mhz
related configuration. This WMI command mismatch between host and
firmware does not cause any real issues because this new member is not
used in 10.4 firmwares so far (10.4.1.00030-1). This difference in WMI
command interface brings in a new wmi_ops for 10.4 gen_peer_assoc().
No noticeable functionality differences with this change can be seen
with the current 10.4 firmwares, but the WMI interface has to be
fixed to work with future 10.4 firmwares which may be using this new
member.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Yanbo Li [Sat, 31 Oct 2015 09:07:21 +0000 (11:07 +0200)]
ath10k: debugfs file to enable Bluetooth coexistence feature
As not all QCA98XX radios are not connected to Bluetooth modules, enabling the
BT coex feature in firmware will have side effects if the radio's GPIO are
connected with other (non-BT) HW modules. Add debugfs file to control the
firmware BT coex logic and set the feature as disable by default to avoid that
btcoex is accidentally enabled.
To enable this feature, execute:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/btcoex
To disable:
echo 0 > /sys/kernel/debug/ieee80211/phyX/ath10k/btcoex
The firmware support this feature since 10.2.4.54 on 2G-only board, dual band
or 5G boards don't support this. The feature's name is WMI_SERVICE_COEX_GPIO
and the btcoex file is not created if firmware doesn't support it.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
[kvalo@qca.qualcomm.com: use btcoex filename and other smaller fixes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vivek Natarajan [Fri, 30 Oct 2015 09:27:58 +0000 (14:57 +0530)]
ath10k: add support for pktlog in QCA99X0
This patch adds pktlog support for 10.4 fw versions.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vasanthakumar Thiagarajan [Thu, 29 Oct 2015 13:41:34 +0000 (19:11 +0530)]
ath10k: add new pdev params defines to 10.4
No functionality change, just sync to the latest
pdev params that 10.4 firmware defines.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vasanthakumar Thiagarajan [Thu, 29 Oct 2015 13:41:33 +0000 (19:11 +0530)]
ath10k: add new WMI cmd/event defines for 10.4
No real functionality change, add WMI command/event
defines to be in sync with 10.4 firmware.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vasanthakumar Thiagarajan [Thu, 29 Oct 2015 13:41:32 +0000 (19:11 +0530)]
ath10k: add new service defines for 10.4
No functional changes, adds new wmi service bits for
10.4 firmware to be sync with 10.4 firmware.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tamizh chelvam [Sat, 31 Oct 2015 09:20:32 +0000 (11:20 +0200)]
ath10k: add thermal throttling support for 10.4 firmware
This patch enables thermal throttling support for 10.4 firmware.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tamizh chelvam [Thu, 29 Oct 2015 12:27:42 +0000 (14:27 +0200)]
ath10k: set peer MFP flag in peer assoc command
Set peer's management frame protection flag in peer assoc command,
this setting will enable/disable encrytion of management frames in fw.
Setting of this flag is based on whether MFP is enabled/disabled at STA
and a firmware feature flag ATH10K_FW_FEATURE_MFP_SUPPORT. This is because
only firmwares 10.1.561 and above have support for MFP.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Manikanta pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tamizh chelvam [Thu, 29 Oct 2015 12:27:37 +0000 (14:27 +0200)]
ath10k: add abstraction layer for peer flags
Abstraction layer for peer flags is added to fix ABI breakage.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Manikanta Pubbisetty [Tue, 20 Oct 2015 06:41:40 +0000 (12:11 +0530)]
ath10k: consolidate if statements in ath10k_wmi_event_mgmt_rx
This patch replaces multiple if conditional checks with a single if condition
in WMI management rx handler. Found during code review.
Signed-off-by: Manikanta Pubbisetty <manikanta.pubbisetty@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ben Greear [Thu, 22 Oct 2015 16:07:39 +0000 (09:07 -0700)]
ath6kl: implement ethtool stats
This supports a way to get target stats through normal
ethtool stats API.
For instance:
# ethtool -S wlan1
NIC statistics:
tx_pkts_nic: 353
tx_bytes_nic: 25142
rx_pkts_nic: 6
rx_bytes_nic: 996
d_tx_ucast_pkts: 89
d_tx_bcast_pkts: 264
d_tx_ucast_bytes: 3020
d_tx_bcast_bytes: 22122
...
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ben Greear [Thu, 22 Oct 2015 16:07:38 +0000 (09:07 -0700)]
ath6kl: break stats gathering code into separate method
This will allow us to call it from elsewhere when implementing
ethtool stats.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ben Greear [Wed, 21 Oct 2015 21:53:21 +0000 (14:53 -0700)]
ath6kl: fix firmware version assignment
Improper use of strlcpy caused garbage to be appended to the
firmware version string. Fix this by paying attention to the
ie_lenth.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ben Greear [Wed, 21 Oct 2015 21:53:20 +0000 (14:53 -0700)]
ath6kl: add error message to explain lack of HT
It can take a user a while to understand why their
NIC that advertises 802.11n support cannot actually
do 802.11n. Print out a warning in the logs to save
the next poor person to use this NIC some trouble.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ben Greear [Wed, 21 Oct 2015 21:53:19 +0000 (14:53 -0700)]
ath6kl: report antenna configuration
This lets 'iw phy phy0 info' report antennas for
the radio device:
...
Available Antennas: TX 0x2 RX 0x2
Configured Antennas: TX 0x2 RX 0x2
...
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vladimir Kondratiev [Sun, 25 Oct 2015 13:59:24 +0000 (15:59 +0200)]
wil6210: handle failure in Tx vring config
When configuring Tx vring for new connection,
WMI call to the firmware may fail. In this case, need to
clean up properly. In particular, need to call
cfg80211_del_sta() in case of AP like interface.
Perform full "disconnect" procedure for proper clean up
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vladimir Kondratiev [Sun, 25 Oct 2015 13:59:23 +0000 (15:59 +0200)]
wil6210: fix device ready detection
Adjust driver behavior during FW boot. Proper sequence of
events after reset and FW download, is as following:
- FW prepares mailbox structure and reports IRQ "FW_READY"
- driver caches mailbox registers, marks mailbox readiness
- FW sends WMI_FW_READY event, ignore it
- FW sends WMI_READY event with some data
- driver stores relevant data marks FW is operational
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Hamad Kadmany [Sun, 25 Oct 2015 13:59:22 +0000 (15:59 +0200)]
wil6210: Fix TSO overflow handling
When Tx ring full is encountered with TSO,
printout of "DMA error" was wrongly printed.
In addition, in case of Tx ring full return
proper error code so that NETDEV_TX_BUSY is
returned to network stack in order not to
drop the packets and retry transmission of the
packets when ring is emptied.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vladimir Kondratiev [Sun, 25 Oct 2015 13:59:21 +0000 (15:59 +0200)]
wil6210: ignore selected WMI events
Some events are ignored for purpose; such events should not
be treated as "unhandled events". Replace info message
saying "unhandled" with debug one saying "ignore", to reduce
dmesg pollution
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Bartosz Markowski [Wed, 28 Oct 2015 14:09:53 +0000 (15:09 +0100)]
ath10k: add QCA9377 chipset support
Add the hardware name, revision and update the pci_id table.
Currently there're two HW ref. designs available I'm aware of,
with 1.0.2 and 1.1 chip revisions. I've access and been using
the first one so far and this patch cover only it.
QCA9377 inherits most of the stuff (e.g. fw interfaces)
from QCA61x4 design, so the integration was pretty straightforward.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rajkumar Manoharan [Tue, 27 Oct 2015 12:21:14 +0000 (17:51 +0530)]
ath10k: reload HT/VHT capabilities on antenna change
To reflect configured antenna settings in HT/VHT MCS map,
reload the HT/VHT capabilities upon antenna change.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rajkumar Manoharan [Tue, 27 Oct 2015 12:21:13 +0000 (17:51 +0530)]
ath10k: move static HT/VHT capability setup functions
Move HT and VHT capabiltity setup static functions to avoid
forward declaration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rajkumar Manoharan [Tue, 27 Oct 2015 12:21:12 +0000 (17:51 +0530)]
ath10k: fill HT/VHT MCS rateset only for configured chainmask
HT/VHT MCS rateset should be filled only for configured chainmask
rather that max supported chainmask. Fix that by checking configured
chainmask while filling HT/VHT MCS rate map.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rajkumar Manoharan [Tue, 27 Oct 2015 12:21:11 +0000 (17:51 +0530)]
ath10k: remove supported chain mask
Removing supported chainmask fields as it can be always derived
from num_rf_chains.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rajkumar Manoharan [Fri, 23 Oct 2015 12:31:06 +0000 (18:01 +0530)]
ath10k: remove shadow copy of CE descriptors for source ring
For the messages from host to target, shadow copy of CE descriptors
are maintained in source ring. Before writing actual CE descriptor,
first shadow copy is filled and then it is copied to CE address space.
To optimize in download path and to reduce d-cache pressure, removing
shadow copy of CE descriptors. This will also reduce driver memory
consumption by 33KB during on device probing.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rajkumar Manoharan [Fri, 23 Oct 2015 12:31:05 +0000 (18:01 +0530)]
ath10k: cleanup copy engine send completion
The physical address necessary to unmap DMA ('bufferp') is stored
in ath10k_skb_cb as 'paddr'. ath10k doesn't rely on the meta/transfer_id
when handling send completion (htc ep id is stored in sk_buff control
buffer). So the unused output arguments {bufferp, nbytesp and transfer_idp}
are removed from CE send completion. This change is needed before removing
the shadow copy of copy engine (CE) descriptors in follow up patch.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rajkumar Manoharan [Fri, 23 Oct 2015 12:31:04 +0000 (18:01 +0530)]
ath10k: remove send completion validation in diag read/write
CE diag window access is serialized (it has to be by design) so
there's no way to get a different send completion. so there's no
need for post completion validation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rajkumar Manoharan [Fri, 23 Oct 2015 12:31:03 +0000 (18:01 +0530)]
ath10k: use local memory instead of shadow descriptor in ce_send
Currently to avoid uncached memory access while filling up copy engine
descriptors, shadow descriptors are used. This can be optimized further
by removing shadow descriptors. To achieve that first shadow ring
dependency in ce_send is removed by creating local copy of the
descriptor on stack and make a one-shot copy into the "uncached"
descriptor.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Manikanta Pubbisetty [Wed, 28 Oct 2015 19:38:33 +0000 (21:38 +0200)]
ath10k: add fw_stats support to 10.4 firmware
This patch adds support for getting firmware debug stats in 10.4 fw.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Alan Liu [Wed, 28 Oct 2015 19:38:32 +0000 (21:38 +0200)]
ath10k: add FW API support to test mode
Add WMI-TLV and FW API support in ath10k testmode.
Ath10k can get right wmi command format from UTF image
to communicate UTF firmware.
Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Maharaja [Wed, 21 Oct 2015 08:49:18 +0000 (11:49 +0300)]
ath10k: enable adaptive CCA
European Union has made it mandatory that all devices working in 2.4 GHz
has to adhere to the ETSI specification (ETSI EN 300 328 V1.9.1)
beginnig this year. The standard basically speaks about interferences
in 2.4Ghz band.
For example, when 802.11 device detects interference, TX must be stopped
as long as interference is present.
Adaptive CCA is a feature, when enabled the device learns from the
environment and configures CCA levels adaptively. This will improve
detecting interferences and the device can stop trasmissions till the
interference is present eventually leading to good performances in
varying interference conditions.
The patch includes code for enabling adaptive CCA for 10.2.4 firmware on
QCA988X.
Signed-off-by: Maharaja <c_mkenna@qti.qualcomm.com>
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rafał Miłecki [Sun, 25 Oct 2015 18:32:43 +0000 (19:32 +0100)]
ssb: add Kconfig entry for compiling SoC related code
This allows saving a little of space when not using ssb on Broadcom SoC.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Sun, 25 Oct 2015 18:32:42 +0000 (19:32 +0100)]
ssb: move functions specific to SoC hosted bus to separated file
This cleans main.c a bit and will allow us to compile SoC related code
conditionally in the future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Thu, 15 Oct 2015 05:23:25 +0000 (07:23 +0200)]
ssb: pick PCMCIA host code support from b43 driver
ssb bus can be found on various "host" devices like PCI/PCMCIA/SDIO.
Every ssb bus contains cores AKA devices.
The main idea is to have ssb driver scan/initialize bus and register
ready-to-use cores. This way ssb drivers can operate on a single core
mostly ignoring underlaying details.
For some reason PCMCIA support was split between ssb and b43. We got
PCMCIA host device probing in b43, then bus scanning in ssb and then
wireless core probing back in b43. The truth is it's very unlikely we
will ever see PCMCIA ssb device with no 802.11 core but I still don't
see any advantage of the current architecture.
With proposed change we get the same functionality with a simpler
architecture, less Kconfig symbols, one killed EXPORT and hopefully
cleaner b43. Since b43 supports both: ssb & bcma I prefer to keep ssb
specific code in ssb driver.
This mostly moves code from b43's pcmcia.c to bridge_pcmcia_80211.c. We
already use similar solution with b43_pci_bridge.c. I didn't use "b43"
in name of this new file as in theory any driver can operate on wireless
core.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Marty Faltesek [Mon, 26 Oct 2015 05:54:01 +0000 (22:54 -0700)]
mwifiex: toggle carrier state in start_ap/stop_ap.
In uap mode the carrier is not enabled until after the first STA joins.
The carrier triggers the bridge to start its state machine, and if STP
is enabled, it takes 4 seconds as it transitions from disabled to
forwarding. During this time the bridge drops all traffic, and the EAPOL
handshake times out after 3 seconds, preventing stations from joining.
Follow the logic used in mac80211 and start the carrier in start_ap
and disable it in stop_ap. This has a nice benefit of allowing the
first station connection time to be reduced by up to 75% when STP is
in use.
Signed-off-by: Martin Faltesek <mfaltesek@google.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
yfw [Mon, 26 Oct 2015 02:36:22 +0000 (10:36 +0800)]
wcn36xx: Remove warning message when dev is NULL for arm64 dma_alloc.
arm64 has requirement that all the dma operations have actual device.
Otherwise, following warnning message shown and dma allocation fails:
WARNING: CPU: 0 PID: 954 at arch/arm64/mm/dma-mapping.c:106 __dma_alloc+0x24c/0x258()
Use an actual device structure for DMA allocation
Modules linked in: wcn36xx wcn36xx_platform
CPU: 0 PID: 954 Comm: ifconfig Not tainted 4.0.0+ #14
Hardware name: Qualcomm Technologies, Inc. MSM 8916 MTP (DT)
Call trace:
[<
ffffffc000089904>] dump_backtrace+0x0/0x124
[<
ffffffc000089a38>] show_stack+0x10/0x1c
[<
ffffffc000627114>] dump_stack+0x80/0xc4
[<
ffffffc0000b2e64>] warn_slowpath_common+0x98/0xd0
[<
ffffffc0000b2ee8>] warn_slowpath_fmt+0x4c/0x58
[<
ffffffc00009487c>] __dma_alloc+0x248/0x258
[<
ffffffbffc009270>] wcn36xx_dxe_allocate_mem_pools+0xc4/0x108 [wcn36xx]
[<
ffffffbffc0079c4>] wcn36xx_start+0x38/0x240 [wcn36xx]
[<
ffffffc0005f161c>] ieee80211_do_open+0x1b0/0x9a4
[<
ffffffc0005f1e68>] ieee80211_open+0x58/0x68
[<
ffffffc00051693c>] __dev_open+0xb0/0x120
[<
ffffffc000516c10>] __dev_change_flags+0x88/0x150
[<
ffffffc000516cf4>] dev_change_flags+0x1c/0x5c
[<
ffffffc000570950>] devinet_ioctl+0x644/0x6f0
Signed-off-by: Yin, Fengwei <fengwei.yin@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bob Copeland [Sat, 24 Oct 2015 17:42:15 +0000 (13:42 -0400)]
wcn36xx: introduce per-channel ring buffer locks
wcn36xx implements a ring buffer for transmitted frames for each
(high and low priority) DMA channel. The ring buffers are lockless:
new frames are inserted at the head of the queue, while finished
packets are reaped from the tail.
Unfortunately, the list manipulations are missing any kind of barriers
so are susceptible to various races: for example, a TX completion
handler might read an updated desc->ctrl before the head has actually
advanced, and then null out the ctl->skb pointer while it is still
being used in the TX path.
Simplify things here by adding a spin lock when traversing the ring.
This change increased stability for me without adding any noticeable
overhead on my platform (xperia z).
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Zefir Kurtisi [Tue, 20 Oct 2015 12:19:26 +0000 (14:19 +0200)]
ath9k: fix phyerror codes
Some of the ath9k_phyerr enums were wrong from the
beginning (and even before). Most of the time the
codes were used for counters to be displayed over
debugfs, which made this a non-functional issue.
Some (e.g. ATH9K_PHYERR_FALSE_RADAR_EXT) are used
for radar detection and require the correct code
to work as intended.
This patch includes:
a) fixes
ATH9K_PHYERR_FALSE_RADAR_EXT: 24 => 36
ATH9K_PHYERR_CCK_LENGTH_ILLEGAL: 32 => 28
ATH9K_PHYERR_CCK_POWER_DROP: 33 => 29
ATH9K_PHYERR_HT_CRC_ERROR: 34 => 32
ATH9K_PHYERR_HT_LENGTH_ILLEGAL: 35 => 33
ATH9K_PHYERR_HT_RATE_ILLEGAL: 36 => 34
b) extensions
ATH9K_PHYERR_CCK_BLOCKER = 24
ATH9K_PHYERR_HT_ZLF = 35
ATH9K_PHYERR_GREEN_FIELD = 37
Aside from the correction and completion made in
the enum, the patch also extends the display of
the related counters in the debugfs.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
John Linville [Mon, 19 Oct 2015 15:15:00 +0000 (11:15 -0400)]
orinoco_usb: return error in ezusb_probe when alloc_orinocodev fails
The current code exits after alloc_orinocodev, but fails to change the
return value to something that indicates the failure. This patch
changes the return value to -ENOMEM.
https://bugzilla.kernel.org/show_bug.cgi?id=106181
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ondrej Zary [Fri, 16 Oct 2015 19:04:14 +0000 (21:04 +0200)]
airo: fix scan after SIOCSIWAP (airo_set_wap)
SIOCSIWAP (airo_set_wap) affects scan: only the AP specified by
SIOCSIWAP is present in scan results.
This makes NetworkManager work for the first time but then unable to
find any other APs.
Clear APList before starting scan and set it back after scan completes
to work-around the problem.
To avoid losing packets during scan, modify disable_MAC() to omit
netif_carrier_off() call when lock == 2.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ondrej Zary [Fri, 16 Oct 2015 19:04:13 +0000 (21:04 +0200)]
airo: Track APList_rid in struct airo_info
Instead of dynamically allocating APList, make it a member of struct
airo_info to always track state of APList_rid.
This simplifies suspend/resume and allows removal of readAPListRid.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Wed, 28 Oct 2015 18:48:26 +0000 (20:48 +0200)]
Merge tag 'iwlwifi-next-for-kalle-2015-10-25' of https://git./linux/kernel/git/iwlwifi/iwlwifi-next
* bug fix for TDLS
* fixes and cleanups in scan
* support of several scan plans
* improvements in FTM
* fixes in FW API
* improvements in the failure paths when the bus is dead
* other various small things here and there
yankejian [Tue, 27 Oct 2015 11:16:34 +0000 (19:16 +0800)]
net: hisilicon: updates HNS config and documents
updates the bindings documents and dtsi file according to the review
comments[https://lkml.org/lkml/2015/9/21/670] from Rob Herring <robh@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li Peng [Tue, 27 Oct 2015 09:17:40 +0000 (17:17 +0800)]
net: hns: fixes the bug tested XGE by ethtool -p
delete action of ETHTOOL_ID_ON/ETHTOOL_ID_OFF in XGE ethtool -p,
so Hardware control the LED state instead of software.
Signed-off-by: Li Peng <lipeng321@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Abhimanyu [Tue, 27 Oct 2015 08:47:43 +0000 (14:17 +0530)]
gianfar: Increase TX_TIMEOUT to 5HZ
Increased TX_TIMEOUT to 5HZ to accommodate worst case situation
for traffic and CPU intensive use cases
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Abhimanyu <abhimanyu@freescale.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 28 Oct 2015 02:56:56 +0000 (19:56 -0700)]
Merge tag 'wireless-drivers-next-for-davem-2015-10-27' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
here's a bigger pull request for 4.4. The diffstat looks scary as we
created a new directory realtek for all realtek drivers. In the future
I'm planning to create similar directories for all vendors, currently we
just have ath, mediatek and realtek. This change has been in linux-next
for a couple of weeks so it should be safe, but of course you never
know.
There's also a new driver rtl8xxxu for few realtek USB devices. This
just made it to the last linux-next build.
Otherwise there's nothing really special, more info below. If time
permits, and it's ok for you, I'm hoping to send you a one more pull
request this week.
brcmfmac
* using netdev carrier state
* add and rework some cfg80211 callbacks mainly for AP mode
* use devcoredump when triggered by firmware event
realtek
* create new directory drivers/net/wireless/realtek/ for all realtek
drivers, not visible to users (no kconfig changes etc)
* add rtl8xxxu, a new mac80211 driver for RTL8723AU, RTL8188CU,
RTL8188RU, RTL8191CU, RTL8192CU and hopefully more in the future
ath10k
* add board 2 API support for automatically choosing correct board file
* data path optimisations
* disable PCI power save for qca988x and QCA99x0 due to interop reasons
wil6210
* BlockAckReq support
* firmware crashdump using devcoredump
* capture all frames with sniffer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tycho Andersen [Tue, 27 Oct 2015 00:23:59 +0000 (09:23 +0900)]
seccomp, ptrace: add support for dumping seccomp filters
This patch adds support for dumping a process' (classic BPF) seccomp
filters via ptrace.
PTRACE_SECCOMP_GET_FILTER allows the tracer to dump the user's classic BPF
seccomp filters. addr should be an integer which represents the ith seccomp
filter (0 is the most recently installed filter). data should be a struct
sock_filter * with enough room for the ith filter, or NULL, in which case
the filter is not saved. The return value for this command is the number of
BPF instructions the program represents, or negative in the case of errors.
Command specific errors are ENOENT: which indicates that there is no ith
filter in this seccomp tree, and EMEDIUMTYPE, which indicates that the ith
filter was not installed as a classic BPF filter.
A caveat with this approach is that there is no way to get explicitly at
the heirarchy of seccomp filters, and users need to memcmp() filters to
decide which are inherited. This means that a task which installs two of
the same filter can potentially confuse users of this interface.
v2: * make save_orig const
* check that the orig_prog exists (not necessary right now, but when
grows eBPF support it will be)
* s/n/filter_off and make it an unsigned long to match ptrace
* count "down" the tree instead of "up" when passing a filter offset
v3: * don't take the current task's lock for inspecting its seccomp mode
* use a 0x42** constant for the ptrace command value
v4: * don't copy to userspace while holding spinlocks
v5: * add another condition to WARN_ON
v6: * rebase on net-next
Signed-off-by: Tycho Andersen <tycho.andersen@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
CC: Will Drewry <wad@chromium.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
CC: Andy Lutomirski <luto@amacapital.net>
CC: Pavel Emelyanov <xemul@parallels.com>
CC: Serge E. Hallyn <serge.hallyn@ubuntu.com>
CC: Alexei Starovoitov <ast@kernel.org>
CC: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 28 Oct 2015 02:53:04 +0000 (19:53 -0700)]
Merge branch 'mpls-multipath-improvements'
Robert Shearman says:
====================
mpls: mulipath improvements
Two improvements to the recently added mpls multipath support. The
first is a fix for missing initialisation the nexthop address length
for the v4 and v6 explicit null label routes, and the second is to
reduce the amount of memory used by mpls routes by changing the way
the via addresses are stored.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Tue, 27 Oct 2015 00:37:36 +0000 (00:37 +0000)]
mpls: reduce memory usage of routes
Nexthops for MPLS routes have a via address field sized for the
largest via address that is expected, which is 32 bytes. This means
that in the most common case of having ipv4 via addresses, 28 bytes of
memory more than required are used per nexthop. In the other common
case of an ipv6 nexthop then 16 bytes more than required are
used. With large numbers of MPLS routes this extra memory usage could
start to become significant.
To avoid allocating memory for a maximum length via address when not
all of it is required and to allow for ease of iterating over
nexthops, then the via addresses are changed to be stored in the same
memory block as the route and nexthops, but in an array after the end
of the array of nexthops. New accessors are provided to retrieve a
pointer to the via address.
To allow for O(1) access without having to store a pointer or offset
per nh, the via address for each nexthop is sized according to the
maximum via address for any nexthop in the route, which is stored in a
new route field, rt_max_alen, but this is in an existing hole in
struct mpls_route so it doesn't increase the size of the
structure. Each via address is ensured to be aligned to VIA_ALEN_ALIGN
to account for architectures that don't allow unaligned accesses.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Tue, 27 Oct 2015 00:37:35 +0000 (00:37 +0000)]
mpls: fix forwarding using v4/v6 explicit null
Fill in the via address length for the predefined IPv4 and IPv6
explicit-null label routes.
Fixes:
f8efb73c97e2 ("mpls: multipath route support")
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Mon, 26 Oct 2015 14:23:42 +0000 (14:23 +0000)]
sfc: replace spinlocks with bit ops for busy poll locking
This patch reduces the overhead of locking for busy poll.
Previously the state was protected by a lock, whereas now
it's manipulated solely with atomic operations.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Frederic Sowa [Mon, 26 Oct 2015 12:51:37 +0000 (13:51 +0100)]
sock: don't enable netstamp for af_unix sockets
netstamp_needed is toggled for all socket families if they request
timestamping. But some protocols don't need the lower-layer timestamping
code at all. This patch starts disabling it for af-unix.
E.g. systemd enables timestamping during boot-up on the journald af-unix
sockets, thus causing the system to globally enable timestamping in the
lower networking stack. Still, it is very probable that timestamping
gets activated, by e.g. dhclient or various NTP implementations.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 28 Oct 2015 02:35:01 +0000 (19:35 -0700)]
Merge branch 'qed-driver'
Ariel Elior says:
====================
Add new drivers: qed & qede
This series implements the driver set for Qlogic's new QL4xxx series.
These are 10/20/25/40/50/100 Gig capable converged nics, supporting
ethernet (obviously), iscsi, fcoe, roce and iwarp protocols.
The overall driver design includes a common module ('qed') and protocol
specific dependent modules for ethernet ('qede'), fcoe ('qedf'),
iscsi ('qedi') and roce ('qedr').
The common module contains all of the common logic, e.g. initialization,
cleanup, infrastructure for interrupt handling, link management, slowpath
etc. as well as protocol agnostic features, and supplying an abstraction
layer for other modules.
The protocol specific modules can be compiled and operated independently
of each other, with the exception of the rdma modules which are dependent
on the ethernet module, in accordance with the kernel rdma stack design.
This series only adds the core and ethernet modules, with basic L2
capabilities. Future series will add the rest of the modules and enhance
the L2 functionality.
Ths patch series is constructed of the following patches:
qed: Add module with basic common support
qed: Add basic L2 interface
qede: Add basic Network driver
qed: Add slowpath L2 support
qede: Add basic network device support
qede: Add classification configuration
qed: Add link support
qede: Add support for link
qed: Add statistics support
qede: Add basic ethtool support
This project is a team effort, thanks go to Yuval Mintz, Dmitry Kravkov,
Michal Kalderon, Tomer Tayar, Manish Chopra, Sudarsana Kalluru,
Rajesh Borundia, Sony Chacko, Artum Zolotushko, Harish Patil, Rasesh Mody,
Sergey Ukhterov and Elad Manela, as well as former team members,
Eilon Greenstein and Shmulik Ravid.
Changes from previos version:
-----------------------------
From Version 7:
- Various small fixes according to Dave's suggestions; Largest change
[code-wise] - don't use tabs for indenting function arguments.
From Version 6:
- Reduced the number of arguments for functions with exceptionally
high number of parameters.
From Version 5:
- Style change and fixes [mostly in 1, 4 and 7].
Thanks go to Francois Romieu, a mere mortal. ;-)
From Version 4:
- Drop dependency for x86_64.
From Version 3:
- Limit support of initial submission to x86_64.
- Fix endian problems appearing via sparse [although no BE support yet].
- Fix small issues suggested by the kbuild test robot.
From Version 2:
- Removed U64_{HI,LO}; Using {upper,lower}_32_bits instead.
- Use regular napi weight definition.
- [We still use the __le variants for variables, since we didn't get
a reply regarding the change into non-user API types].
From Version 1:
- Removed private license file; Instead revised comments at source headers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Kalluru [Mon, 26 Oct 2015 09:02:34 +0000 (11:02 +0200)]
qede: Add basic ethtool support
This adds basic ethtool operations to the qed driver, allowing support in:
- Statistics gathering [ethtool -S]
- Setting of debug level [ethtool -s <interface> msglvl]
- Getting basic information [ethtool, ethtool -i]
In addition it adds the ability to change the MTU.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Mon, 26 Oct 2015 09:02:33 +0000 (11:02 +0200)]
qed: Add statistics support
Device statistics can be gathered on-demand. This adds the qed support for
reading the statistics [both function and port] from the device, and adds
to the public API a method for requesting the current statistics.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Kalluru [Mon, 26 Oct 2015 09:02:32 +0000 (11:02 +0200)]
qede: Add support for link
This adds basic link functionality to qede - driver still doesn't provide
users with an API to change any link property, but it does request qed to
initialize the link using default configuration, and registers a callback
that allows it to get link notifications.
This patch adds the ability of the driver to set the carrier as active and
to enable traffic as a result of async. link notifications.
Following this patch, driver should be capable of running traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 26 Oct 2015 09:02:31 +0000 (11:02 +0200)]
qed: Add link support
Physical link is handled by the management Firmware.
This patch lays the infrastructure for attention handling in the driver,
as link change notifications arrive via async. attentions,
as well the handling of such notifications.
This patch also extends the API with the protocol drivers by adding
registered callbacks which the protocol driver passes to qed in order
to be notified of async. events originating from the FW/HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Kalluru [Mon, 26 Oct 2015 09:02:30 +0000 (11:02 +0200)]
qede: classification configuration
Add the ability to configure basic classification in driver by
implementing ndo_set_mac_address() and ndo_set_rx_mode().
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 26 Oct 2015 09:02:29 +0000 (11:02 +0200)]
qede: Add basic network device support
This patch includes the basic Rx/Tx support for the driver [although
carrier will still never be turned on].
Following this patch the driver registers a network device, initializes
it and prepares it for traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Mon, 26 Oct 2015 09:02:28 +0000 (11:02 +0200)]
qed: Add slowpath L2 support
This patch adds to the qed the support to configure various L2 elements,
such as channels and basic filtering conditions.
It also enhances its public API to allow qede to later utilize this
functionality.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 26 Oct 2015 09:02:27 +0000 (11:02 +0200)]
qede: Add basic Network driver
The Qlogic Everest Driver for Ethernet is the Ethernet specific module for
QL4xxx ethernet products by Qlogic.
This patch adds a very minimal PCI driver, one that doesn't yet register
a network device, but one that does interact with qed and does a basic
initialization of the HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 26 Oct 2015 09:02:26 +0000 (11:02 +0200)]
qed: Add basic L2 interface
This patch adds a public API for a network driver to work on top of QED.
The interface itself is very minimal - it's mostly infrastructure, as the
only content it has after this patch is a query for HW-based information
required for the creation of a network interface [I.e., no actual
protocol-specific configurations are supported].
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 26 Oct 2015 09:02:25 +0000 (11:02 +0200)]
qed: Add module with basic common support
The Qlogic Everest Driver is the backend module for the QL4xxx ethernet
products by Qlogic.
This module serves two main purposes:
1. It's responsible to contain all the common code that will be shared
between the various drivers that would be used with said line of
products. Flows such as chip initialization and de-initialization
fall under this category.
2. It would abstract the protocol-specific HW & FW components, allowing
the protocol drivers to have a clean APIs which is detached in its
slowpath configuration from the actual HSI.
This adds a very basic module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
emmanuel.grumbach@intel.com [Mon, 26 Oct 2015 08:31:29 +0000 (10:31 +0200)]
net: tso: add support for IPv6
Adding IPv6 for the TSO helper API is trivial:
* Don't play with the id (which doesn't exist in IPv6)
* Correctly update the payload_len (don't include the
length of the IP header itself)
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 27 Oct 2015 05:16:02 +0000 (22:16 -0700)]
Merge tag 'arcnet-for-4.4-rc1' of git://git.pengutronix.de/git/mgr/linux
Michael Grzeschik says:
====================
This series includes code simplifaction. The main changes are the correct
xceiver handling (enable/disable) of the com20020 cards. The driver now handles
link status change detection. The EAE PCI-ARCNET cards now make use of the
rotary encoded subdevice indexing and got support for led triggers on transmit
and reconnection events.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Sat, 24 Oct 2015 12:00:20 +0000 (14:00 +0200)]
ipv6: icmp: include addresses in debug messages
Messages like "icmp6_send: no reply to icmp error" are close
to useless. Adding source and destination addresses to provide
some more clue.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov [Fri, 23 Oct 2015 21:58:19 +0000 (14:58 -0700)]
bpf: make tracing helpers gpl only
exported perf symbols are GPL only, mark eBPF helper functions
used in tracing as GPL only as well.
Suggested-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov [Fri, 23 Oct 2015 00:10:14 +0000 (17:10 -0700)]
bpf: fix bpf_perf_event_read() helper
Fix safety checks for bpf_perf_event_read():
- only non-inherited events can be added to perf_event_array map
(do this check statically at map insertion time)
- dynamically check that event is local and !pmu->count
Otherwise buggy bpf program can cause kernel splat.
Also fix error path after perf_event_attrs()
and remove redundant 'extern'.
Fixes:
35578d798400 ("bpf: Implement function bpf_perf_event_read() that get the selected hardware PMU conuter")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 23 Oct 2015 19:11:08 +0000 (12:11 -0700)]
net: dsa: bcm_sf2: Unhardcode port numbers
While the current driver mostly supports BCM7445 which has a hardcoded
location for its MoCA port on port 7 and port 0 for its internal PHY,
this is not necessarily true for all other chips out there such as
BCM3390 for instance.
Walk the list of ports from Device Tree, get their port number ("reg"
property), and then parse the "phy-mode" property and initialize two
internal variables: moca_port and a bitmask of internal PHYs. Since we
use interrupts for the MoCA port, we introduce two helper functions to
enable/disable interrupts and do this at the appropriate bank (INTRL2_0
or INTRL2_1).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 23 Oct 2015 18:38:07 +0000 (11:38 -0700)]
net: dsa: bcm_sf2: Implement FDB operations
Add support for the FDB add, delete, and dump operations. The add and
delete operations are implemented using directed ARL operations using
the specified MAC address and consist in a read operation, write and
readback operation.
The dump operation consists in using the ARL search and software
filtering entries which are not for the desired port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo [Sun, 25 Oct 2015 16:24:38 +0000 (18:24 +0200)]
rtl8xxxu: fix unused rtl8192cu_fops compiler warning
kbuild reported:
rtl8xxxu.c:5786:32: warning: ‘rtl8192cu_fops’ defined but not used [-Wunused-variable]
Fix it by adding temporary ifdefs around the static functions.
Fixes:
033695bdf6d7 ("rtl8xxxu: move devices supported by rtlwifi under UNTESTED config")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Michael Grzeschik [Wed, 16 Sep 2015 08:15:45 +0000 (10:15 +0200)]
arcnet: add netif_carrier_on/off for reconnect
The arcnet device has no interrupt to detect if the link has changed
from disconnected to connected. This patch adds an timer to toggle the
link detection. The timer will get retriggered as long as the
reconnection interrupts accure. If the recon interrupts hold off
for >1s we define the connection stable again.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Michael Grzeschik [Wed, 17 Sep 2014 22:12:50 +0000 (00:12 +0200)]
arcnet: com20020-pci: add led trigger support
The EAE PLX-PCI card has special leds on the the main io pci resource
bar. This patch adds support to trigger the conflict and data leds with
the packages.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Michael Grzeschik [Wed, 17 Sep 2014 22:12:50 +0000 (00:12 +0200)]
arcnet: com20020-pci: add rotary index support
The EAE PLX-PCI card has a special rotary encoder
to configure the address of every card individually.
We take this information for the initial setup of
the cards dev_id.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Michael Grzeschik [Fri, 20 Mar 2015 14:22:24 +0000 (15:22 +0100)]
arcnet: com20020-pci: set dev_port to the subdevice index
This patch sets the dev_port according to the index of
the card. This can be used by udev to name the ports
in userspace.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Michael Grzeschik [Fri, 20 Mar 2015 14:20:59 +0000 (15:20 +0100)]
arcnet: com20020: add enable and disable device on open/close
This patch changes the driver to properly work with the linux netif
interface. The controller gets enabled on open and disabled on close.
Therefor it removes every bogus start of the xceiver. It only gets
enabled on com20020_open and disabled on com20020_close.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Michael Grzeschik [Wed, 22 Apr 2015 14:41:46 +0000 (16:41 +0200)]
arcnet: move dev_free_skb to its only user
The call for dev_free_skb is done only once. This patch
moves its call to its only user and removes the obsolete
condition variable.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Michael Chan [Mon, 26 Oct 2015 02:27:57 +0000 (22:27 -0400)]
bnxt_en: Fix compile warnings when CONFIG_INET is not set.
bnxt_gro_skb() has unused variables when CONFIG_INET is not set. We
really cannot support hardware GRO if CONFIG_INET is not set, so
compile out bnxt_gro_skb() completely and define BNXT_FLAG_GRO to be 0
if CONFIG_INET is not set. This will effectively always disable
hardware GRO if CONFIG_INET is not set.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Ringle [Thu, 22 Oct 2015 19:09:04 +0000 (15:09 -0400)]
net: encx24j600: Fix mask to update LED configuration
This fixes the mask used to update the LED configuration so that it clears
the necessary bits as well as setting the bits according to the mask.
Also reverse the LED configuration to show the Link state + collisions in
LEDA and the Link state + TX/RX events in LEDB.
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 26 Oct 2015 01:20:41 +0000 (18:20 -0700)]
Merge branch 'mvneta-ethtool-stats'
Russell King says:
====================
mvneta ethtool statistics
Sorry for v3 - I forgot to update the commit message on patch 1 as
requested by Marcin.
This short series adds ethtool statistics reporting to mvneta. Having
discussed with Andrew on IRC, we decided I'd pick up his patch into my
series.
My change for patch 1 compared to the previous RFC splits out the
reading of the statistics from the hardware into a separate function,
in order to facilitate work going on elsewhere to arrange for the
statistics to be preserved across a suspend/resume cycle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 22 Oct 2015 17:37:36 +0000 (18:37 +0100)]
net: mvneta: Fix clearing of MIB statistics
The existing function to clear the MIB statatistics was using the
wrong address for the registers. Also, the counters would of been
cleared when the interface was brought up, not during the
probe. Fix both of these.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 22 Oct 2015 17:37:30 +0000 (18:37 +0100)]
net: mvneta: add ethtool statistics
Add support for the ethtool statistic interface, returning the full set
of statistics which both Armada 370, 38x and Armada XP can support.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 23 Oct 2015 17:59:16 +0000 (10:59 -0700)]
af_unix: do not report POLLOUT on listeners
poll(POLLOUT) on a listener should not report fd is ready for
a write().
This would break some applications using poll() and pfd.events = -1,
as they would not block in poll()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Alan Burlison <Alan.Burlison@oracle.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wu Fengguang [Sat, 24 Oct 2015 14:56:01 +0000 (22:56 +0800)]
tipc: link_is_bc_sndlink() can be static
TO: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: Jon Maloy <jon.maloy@ericsson.com>
CC: Ying Xue <ying.xue@windriver.com>
CC: tipc-discussion@lists.sourceforge.net
CC: linux-kernel@vger.kernel.org
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moshe Harel [Thu, 10 Sep 2015 12:29:09 +0000 (15:29 +0300)]
iwlwifi: nvm: free old section data when reading nvm file
When reading external NVM file, if a section exists both in OTP
and in the external file, the memory that was allocated at OTP
reading is not freed.
This is possible only on systems that have an external NVM
file which is typically the case on embedded systems.
Signed-off-by: Moshe Harel <moshe.harel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Arik Nemtsov [Mon, 12 Oct 2015 11:47:11 +0000 (14:47 +0300)]
iwlwifi: mvm: disable TDLS ac queues correctly
The iwl_mvm_disable_queue function requires the TID to be set to
IWL_MAX_TID_COUNT when disabling an AC queue. Call it correctly for TDLS
scenarios.
Fixes:
4ecafae9e568 ("iwlwifi: mvm: support using multiple ACs on single HW queue")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eliad Peller [Thu, 15 Oct 2015 07:58:48 +0000 (10:58 +0300)]
iwlwifi: mvm: take scan ref only on success
In some cases, scan reference was taken, but wasn't
released even though scan command wasn't actually issued.
Change the current code to simply take the reference
only on success.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Johannes Berg [Fri, 11 Sep 2015 10:07:21 +0000 (12:07 +0200)]
iwlwifi: mvm: remove pointless scan plan checks
As cfg80211 already enforces these limits, there's little point
in having them again here in our code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Johannes Berg [Fri, 11 Sep 2015 10:09:22 +0000 (12:09 +0200)]
iwlwifi: mvm: clean up some whitespace in scan code
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Andrei Otcheretianski [Tue, 30 Jun 2015 09:08:28 +0000 (12:08 +0300)]
iwlwifi: mvm: Implement per vif frame registration API
Implement config_iface_filter() driver op. Currently support only
probe request registration for p2p client vifs, by setting
MAC_FILTER_IN_PROBE_REQUEST flag in MAC_CONTEXT_CMD.
This is needed since WFDS spec and certification require a P2P client
to be discoverable on its operating channel.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eliad Peller [Thu, 10 Sep 2015 12:00:22 +0000 (15:00 +0300)]
iwlwifi: avoid read/write operations if the bus is dead
Recovery takes too much time if the bus is dead (each timeout
is 2000ms, etc.).
Explicitly skip fw dump in this case, as it will result in
garbage data (and might take signifcant time)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Avraham Stern [Wed, 19 Aug 2015 09:46:12 +0000 (12:46 +0300)]
iwlwifi: mvm: Add support for two scheduled scan plans
Add support for two scan plans for scheduled scan. The first plan
will run for a limited number of iterations, then the second plan
will run infinitely.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Luca Coelho [Tue, 6 Oct 2015 06:54:57 +0000 (09:54 +0300)]
iwlwifi: mvm: let any command flag be passed to iwl_mvm_flushtx_path()
Instead of only allowing the caller to decide whether the CMD_ASYNC
flag is set, let it pass the entire flags bitmask. This allows more
flexibility and will be needed when we call this function in the
suspend flow (where other flags are needed).
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Assaf Krauss [Wed, 12 Aug 2015 14:52:12 +0000 (17:52 +0300)]
iwlwifi: mvm: Allow setting ctrl-chnl-position in FTM responder
This patch enables the debugfs user to configure an FTM responder
with the appropriate control channel position.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Johannes Berg [Tue, 6 Oct 2015 12:07:44 +0000 (14:07 +0200)]
iwlwifi: mvm: use short timeouts in P2P low latency if supported
Those timeouts are used for AM-to-PSM transition.
We already have those pairs defined for default and WOWLAN use cases.
We expect that by using shorter threshold for low latency P2P,
e.g. for Miracast video scenario, we might save a considerable amount of power.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Johannes Berg [Tue, 6 Oct 2015 11:28:48 +0000 (13:28 +0200)]
iwlwifi: mvm: use wowlan RX/TX timeouts in D0i3
In "hostless" mode (D3 or D0i3) the same parameters were intended
to be used, but the code doesn't do that properly. Fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Arik Nemtsov [Tue, 6 Oct 2015 09:22:47 +0000 (12:22 +0300)]
iwlwifi: mvm: correctly request DTS-measure for new cards
Since the 8000 series, the DTS measurement request command has been
changed. Use an ucode capability flag to determine which version is
supported and send the extended command when needed.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Emmanuel Grumbach [Wed, 21 Oct 2015 16:55:32 +0000 (19:55 +0300)]
iwlwifi: pcie: fix (again) prepare card flow
The hardware bug in the commit mentioned below forces us
not to re-enable the clock gating in the Host Cluster.
The impact on the power consumption is minimal and it allows
the WAKE_ME interrupt to propagate.
CC: <stable@vger.kernel.org> [4.1+]
Fixes:
c9fdec9f3970 ("iwlwifi: pcie: fix prepare card flow")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>