OSDN Git Service
Håkon Bugge [Sun, 17 Feb 2019 14:45:12 +0000 (15:45 +0100)]
IB/mlx4: Increase the timeout for CM cache
[ Upstream commit
2612d723aadcf8281f9bf8305657129bd9f3cd57 ]
Using CX-3 virtual functions, either from a bare-metal machine or
pass-through from a VM, MAD packets are proxied through the PF driver.
Since the VF drivers have separate name spaces for MAD Transaction Ids
(TIDs), the PF driver has to re-map the TIDs and keep the book keeping
in a cache.
Following the RDMA Connection Manager (CM) protocol, it is clear when
an entry has to evicted form the cache. But life is not perfect,
remote peers may die or be rebooted. Hence, it's a timeout to wipe out
a cache entry, when the PF driver assumes the remote peer has gone.
During workloads where a high number of QPs are destroyed concurrently,
excessive amount of CM DREQ retries has been observed
The problem can be demonstrated in a bare-metal environment, where two
nodes have instantiated 8 VFs each. This using dual ported HCAs, so we
have 16 vPorts per physical server.
64 processes are associated with each vPort and creates and destroys
one QP for each of the remote 64 processes. That is, 1024 QPs per
vPort, all in all 16K QPs. The QPs are created/destroyed using the
CM.
When tearing down these 16K QPs, excessive CM DREQ retries (and
duplicates) are observed. With some cat/paste/awk wizardry on the
infiniband_cm sysfs, we observe as sum of the 16 vPorts on one of the
nodes:
cm_rx_duplicates:
dreq 2102
cm_rx_msgs:
drep 1989
dreq 6195
rep 3968
req 4224
rtu 4224
cm_tx_msgs:
drep 4093
dreq 27568
rep 4224
req 3968
rtu 3968
cm_tx_retries:
dreq 23469
Note that the active/passive side is equally distributed between the
two nodes.
Enabling pr_debug in cm.c gives tons of:
[171778.814239] <mlx4_ib> mlx4_ib_multiplex_cm_handler: id{slave:
1,sl_cm_id: 0xd393089f} is NULL!
By increasing the CM_CLEANUP_CACHE_TIMEOUT from 5 to 30 seconds, the
tear-down phase of the application is reduced from approximately 90 to
50 seconds. Retries/duplicates are also significantly reduced:
cm_rx_duplicates:
dreq 2460
[]
cm_tx_retries:
dreq 3010
req 47
Increasing the timeout further didn't help, as these duplicates and
retries stems from a too short CMA timeout, which was 20 (~4 seconds)
on the systems. By increasing the CMA timeout to 22 (~17 seconds), the
numbers fell down to about 10 for both of them.
Adjustment of the CMA timeout is not part of this commit.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Acked-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dongli Zhang [Fri, 22 Feb 2019 14:10:20 +0000 (22:10 +0800)]
loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()
[ Upstream commit
758a58d0bc67457f1215321a536226654a830eeb ]
Commit
0da03cab87e6
("loop: Fix deadlock when calling blkdev_reread_part()") moves
blkdev_reread_part() out of the loop_ctl_mutex. However,
GENHD_FL_NO_PART_SCAN is set before __blkdev_reread_part(). As a result,
__blkdev_reread_part() will fail the check of GENHD_FL_NO_PART_SCAN and
will not rescan the loop device to delete all partitions.
Below are steps to reproduce the issue:
step1 # dd if=/dev/zero of=tmp.raw bs=1M count=100
step2 # losetup -P /dev/loop0 tmp.raw
step3 # parted /dev/loop0 mklabel gpt
step4 # parted -a none -s /dev/loop0 mkpart primary 64s 1
step5 # losetup -d /dev/loop0
Step5 will not be able to delete /dev/loop0p1 (introduced by step4) and
there is below kernel warning message:
[ 464.414043] __loop_clr_fd: partition scan of loop0 failed (rc=-22)
This patch sets GENHD_FL_NO_PART_SCAN after blkdev_reread_part().
Fixes:
0da03cab87e6 ("loop: Fix deadlock when calling blkdev_reread_part()")
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vadim Pasternak [Sun, 17 Feb 2019 18:15:30 +0000 (18:15 +0000)]
platform/mellanox: mlxreg-hotplug: Fix KASAN warning
[ Upstream commit
e4c275f77624961b56cce397814d9d770a45ac59 ]
Fix the following KASAN warning produced when booting a 64-bit kernel:
[ 13.334750] BUG: KASAN: stack-out-of-bounds in find_first_bit+0x19/0x70
[ 13.342166] Read of size 8 at addr
ffff880235067178 by task kworker/2:1/42
[ 13.342176] CPU: 2 PID: 42 Comm: kworker/2:1 Not tainted 4.20.0-rc1+ #106
[ 13.342179] Hardware name: Mellanox Technologies Ltd. MSN2740/Mellanox x86 SFF board, BIOS 5.6.5 06/07/2016
[ 13.342190] Workqueue: events deferred_probe_work_func
[ 13.342194] Call Trace:
[ 13.342206] dump_stack+0xc7/0x15b
[ 13.342214] ? show_regs_print_info+0x5/0x5
[ 13.342220] ? kmsg_dump_rewind_nolock+0x59/0x59
[ 13.342234] ? _raw_write_lock_irqsave+0x100/0x100
[ 13.351593] print_address_description+0x73/0x260
[ 13.351603] kasan_report+0x260/0x380
[ 13.351611] ? find_first_bit+0x19/0x70
[ 13.351619] find_first_bit+0x19/0x70
[ 13.351630] mlxreg_hotplug_work_handler+0x73c/0x920 [mlxreg_hotplug]
[ 13.351639] ? __lock_text_start+0x8/0x8
[ 13.351646] ? _raw_write_lock_irqsave+0x80/0x100
[ 13.351656] ? mlxreg_hotplug_remove+0x1e0/0x1e0 [mlxreg_hotplug]
[ 13.351663] ? regmap_volatile+0x40/0xb0
[ 13.351668] ? regcache_write+0x4c/0x90
[ 13.351676] ? mlxplat_mlxcpld_reg_write+0x24/0x30 [mlx_platform]
[ 13.351681] ? _regmap_write+0xea/0x220
[ 13.351688] ? __mutex_lock_slowpath+0x10/0x10
[ 13.351696] ? devm_add_action+0x70/0x70
[ 13.351701] ? mutex_unlock+0x1d/0x40
[ 13.351710] mlxreg_hotplug_probe+0x82e/0x989 [mlxreg_hotplug]
[ 13.351723] ? mlxreg_hotplug_work_handler+0x920/0x920 [mlxreg_hotplug]
[ 13.351731] ? sysfs_do_create_link_sd.isra.2+0xf4/0x190
[ 13.351737] ? sysfs_rename_link_ns+0xf0/0xf0
[ 13.351743] ? devres_close_group+0x2b0/0x2b0
[ 13.351749] ? pinctrl_put+0x20/0x20
[ 13.351755] ? acpi_dev_pm_attach+0x2c/0xd0
[ 13.351763] platform_drv_probe+0x70/0xd0
[ 13.351771] really_probe+0x480/0x6e0
[ 13.351778] ? device_attach+0x10/0x10
[ 13.351784] ? __lock_text_start+0x8/0x8
[ 13.351790] ? _raw_write_lock_irqsave+0x80/0x100
[ 13.351797] ? _raw_write_lock_irqsave+0x80/0x100
[ 13.351806] ? __driver_attach+0x190/0x190
[ 13.351812] driver_probe_device+0x17d/0x1a0
[ 13.351819] ? __driver_attach+0x190/0x190
[ 13.351825] bus_for_each_drv+0xd6/0x130
[ 13.351831] ? bus_rescan_devices+0x20/0x20
[ 13.351837] ? __mutex_lock_slowpath+0x10/0x10
[ 13.351845] __device_attach+0x18c/0x230
[ 13.351852] ? device_bind_driver+0x70/0x70
[ 13.351859] ? __mutex_lock_slowpath+0x10/0x10
[ 13.351866] bus_probe_device+0xea/0x110
[ 13.351874] deferred_probe_work_func+0x1c9/0x290
[ 13.351882] ? driver_deferred_probe_add+0x1d0/0x1d0
[ 13.351889] ? preempt_notifier_dec+0x20/0x20
[ 13.351897] ? read_word_at_a_time+0xe/0x20
[ 13.351904] ? strscpy+0x151/0x290
[ 13.351912] ? set_work_pool_and_clear_pending+0x9c/0xf0
[ 13.351918] ? __switch_to_asm+0x34/0x70
[ 13.351924] ? __switch_to_asm+0x40/0x70
[ 13.351929] ? __switch_to_asm+0x34/0x70
[ 13.351935] ? __switch_to_asm+0x40/0x70
[ 13.351942] process_one_work+0x5cc/0xa00
[ 13.351952] ? pwq_dec_nr_in_flight+0x1e0/0x1e0
[ 13.351960] ? pci_mmcfg_check_reserved+0x80/0xb8
[ 13.351967] ? run_rebalance_domains+0x250/0x250
[ 13.351980] ? stack_access_ok+0x35/0x80
[ 13.351986] ? deref_stack_reg+0xa1/0xe0
[ 13.351994] ? schedule+0xcd/0x250
[ 13.352000] ? worker_enter_idle+0x2d6/0x330
[ 13.352006] ? __schedule+0xeb0/0xeb0
[ 13.352014] ? fork_usermode_blob+0x130/0x130
[ 13.352019] ? mutex_lock+0xa7/0x100
[ 13.352026] ? _raw_spin_lock_irq+0x98/0xf0
[ 13.352032] ? _raw_read_unlock_irqrestore+0x30/0x30
[ 13.352037] i2c i2c-2: Added multiplexed i2c bus 11
[ 13.352043] worker_thread+0x181/0xa80
[ 13.352052] ? __switch_to_asm+0x34/0x70
[ 13.352058] ? __switch_to_asm+0x40/0x70
[ 13.352064] ? process_one_work+0xa00/0xa00
[ 13.352070] ? __switch_to_asm+0x34/0x70
[ 13.352076] ? __switch_to_asm+0x40/0x70
[ 13.352081] ? __switch_to_asm+0x34/0x70
[ 13.352086] ? __switch_to_asm+0x40/0x70
[ 13.352092] ? __switch_to_asm+0x34/0x70
[ 13.352097] ? __switch_to_asm+0x40/0x70
[ 13.352105] ? __schedule+0x3d6/0xeb0
[ 13.352112] ? migrate_swap_stop+0x470/0x470
[ 13.352119] ? save_stack+0x89/0xb0
[ 13.352127] ? kmem_cache_alloc_trace+0xe5/0x570
[ 13.352132] ? kthread+0x59/0x1d0
[ 13.352138] ? ret_from_fork+0x35/0x40
[ 13.352154] ? __schedule+0xeb0/0xeb0
[ 13.352161] ? remove_wait_queue+0x150/0x150
[ 13.352169] ? _raw_write_lock_irqsave+0x80/0x100
[ 13.352175] ? __lock_text_start+0x8/0x8
[ 13.352183] ? process_one_work+0xa00/0xa00
[ 13.352188] kthread+0x1a4/0x1d0
[ 13.352195] ? kthread_create_worker_on_cpu+0xc0/0xc0
[ 13.352202] ret_from_fork+0x35/0x40
[ 13.353879] The buggy address belongs to the page:
[ 13.353885] page:
ffffea0008d419c0 count:0 mapcount:0 mapping:
0000000000000000 index:0x0
[ 13.353890] flags: 0x2ffff8000000000()
[ 13.353897] raw:
02ffff8000000000 ffffea0008d419c8 ffffea0008d419c8 0000000000000000
[ 13.353903] raw:
0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
[ 13.353905] page dumped because: kasan: bad access detected
[ 13.353908] Memory state around the buggy address:
[ 13.353912]
ffff880235067000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 13.353917]
ffff880235067080: 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1 04
[ 13.353921] >
ffff880235067100: f2 f2 f2 f2 f2 f2 f2 04 f2 f2 f2 f2 f2 f2 f2 04
[ 13.353923] ^
[ 13.353927]
ffff880235067180: f2 f2 f2 f2 f2 f2 f2 04 f2 f2 f2 00 00 00 00 00
[ 13.353931]
ffff880235067200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 13.353933] ==================================================================
The warning is caused by the below loop:
for_each_set_bit(bit, (unsigned long *)&asserted, 8) {
while "asserted" is declared as 'unsigned'.
The casting of 32-bit unsigned integer pointer to a 64-bit unsigned long
pointer. There are two problems here.
It causes the access of four extra byte, which can corrupt memory
The 32-bit pointer address may not be 64-bit aligned.
The fix changes variable "asserted" to "unsigned long".
Fixes:
1f976f6978bf ("platform/x86: Move Mellanox platform hotplug driver to platform/mellanox")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yang Fan [Sat, 19 Jan 2019 11:16:33 +0000 (19:16 +0800)]
platform/x86: ideapad-laptop: Fix no_hw_rfkill_list for Lenovo RESCUER R720-15IKBN
[ Upstream commit
4d9b2864a415fec39150bc13efc730c7eb88711e ]
Commit
ae7c8cba3221 ("platform/x86: ideapad-laptop: add lenovo RESCUER
R720-15IKBN to no_hw_rfkill_list") added
DMI_MATCH(DMI_BOARD_NAME, "80WW")
for Lenovo RESCUER R720-15IKBN.
But DMI_BOARD_NAME does not match 80WW on Lenovo RESCUER R720-15IKBN,
thus cause Wireless LAN still be hard blocked.
On Lenovo RESCUER R720-15IKBN:
~$ cat /sys/class/dmi/id/sys_vendor
LENOVO
~$ cat /sys/class/dmi/id/board_name
Provence-5R3
~$ cat /sys/class/dmi/id/product_name
80WW
~$ cat /sys/class/dmi/id/product_version
Lenovo R720-15IKBN
So on Lenovo RESCUER R720-15IKBN:
DMI_SYS_VENDOR should match "LENOVO",
DMI_BOARD_NAME should match "Provence-5R3",
DMI_PRODUCT_NAME should match "80WW",
DMI_PRODUCT_VERSION should match "Lenovo R720-15IKBN".
Fix it, and in according with other entries in no_hw_rfkill_list,
use DMI_PRODUCT_VERSION instead of DMI_BOARD_NAME.
Fixes:
ae7c8cba3221 ("platform/x86: ideapad-laptop: add lenovo RESCUER R720-15IKBN to no_hw_rfkill_list")
Signed-off-by: Yang Fan <nullptr.cpp@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Florian Fainelli [Fri, 22 Feb 2019 04:09:26 +0000 (20:09 -0800)]
mlxsw: spectrum: Avoid -Wformat-truncation warnings
[ Upstream commit
ab2c4e2581ad32c28627235ff0ae8c5a5ea6899f ]
Give precision identifiers to the two snprintf() formatting the priority
and TC strings to avoid producing these two warnings:
drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_prio_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:37: warning: '%d'
directive output may be truncated writing between 1 and 3 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:3: note: 'snprintf'
output between 3 and 36 bytes into a destination of size 32
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
mlxsw_sp_port_hw_prio_stats[i].str, prio);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_tc_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:37: warning: '%d'
directive output may be truncated writing between 1 and 11 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:3: note: 'snprintf'
output between 3 and 44 bytes into a destination of size 32
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
mlxsw_sp_port_hw_tc_stats[i].str, tc);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Florian Fainelli [Fri, 22 Feb 2019 04:09:28 +0000 (20:09 -0800)]
e1000e: Fix -Wformat-truncation warnings
[ Upstream commit
135e7245479addc6b1f5d031e3d7e2ddb3d2b109 ]
Provide precision hints to snprintf() since we know the destination
buffer size of the RX/TX ring names are IFNAMSIZ + 5 - 1. This fixes the
following warnings:
drivers/net/ethernet/intel/e1000e/netdev.c: In function
'e1000_request_msix':
drivers/net/ethernet/intel/e1000e/netdev.c:2109:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-rx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2107:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->rx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->rx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-rx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/e1000e/netdev.c:2125:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-tx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2123:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->tx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->tx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-tx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Andrew Lunn [Sat, 23 Feb 2019 16:43:56 +0000 (17:43 +0100)]
net: dsa: mv88e6xxx: Add lockdep classes to fix false positive splat
[ Upstream commit
f6d9758b12660484b6639364cc406da92a918c96 ]
The following false positive lockdep splat has been observed.
======================================================
WARNING: possible circular locking dependency detected
4.20.0+ #302 Not tainted
------------------------------------------------------
systemd-udevd/160 is trying to acquire lock:
edea6080 (&chip->reg_lock){+.+.}, at: __setup_irq+0x640/0x704
but task is already holding lock:
edff0340 (&desc->request_mutex){+.+.}, at: __setup_irq+0xa0/0x704
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&desc->request_mutex){+.+.}:
mutex_lock_nested+0x1c/0x24
__setup_irq+0xa0/0x704
request_threaded_irq+0xd0/0x150
mv88e6xxx_probe+0x41c/0x694 [mv88e6xxx]
mdio_probe+0x2c/0x54
really_probe+0x200/0x2c4
driver_probe_device+0x5c/0x174
__driver_attach+0xd8/0xdc
bus_for_each_dev+0x58/0x7c
bus_add_driver+0xe4/0x1f0
driver_register+0x7c/0x110
mdio_driver_register+0x24/0x58
do_one_initcall+0x74/0x2e8
do_init_module+0x60/0x1d0
load_module+0x1968/0x1ff4
sys_finit_module+0x8c/0x98
ret_fast_syscall+0x0/0x28
0xbedf2ae8
-> #0 (&chip->reg_lock){+.+.}:
__mutex_lock+0x50/0x8b8
mutex_lock_nested+0x1c/0x24
__setup_irq+0x640/0x704
request_threaded_irq+0xd0/0x150
mv88e6xxx_g2_irq_setup+0xcc/0x1b4 [mv88e6xxx]
mv88e6xxx_probe+0x44c/0x694 [mv88e6xxx]
mdio_probe+0x2c/0x54
really_probe+0x200/0x2c4
driver_probe_device+0x5c/0x174
__driver_attach+0xd8/0xdc
bus_for_each_dev+0x58/0x7c
bus_add_driver+0xe4/0x1f0
driver_register+0x7c/0x110
mdio_driver_register+0x24/0x58
do_one_initcall+0x74/0x2e8
do_init_module+0x60/0x1d0
load_module+0x1968/0x1ff4
sys_finit_module+0x8c/0x98
ret_fast_syscall+0x0/0x28
0xbedf2ae8
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&desc->request_mutex);
lock(&chip->reg_lock);
lock(&desc->request_mutex);
lock(&chip->reg_lock);
&desc->request_mutex refer to two different mutex. #1 is the GPIO for
the chip interrupt. #2 is the chained interrupt between global 1 and
global 2.
Add lockdep classes to the GPIO interrupt to avoid this.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Aaro Koskinen [Sat, 2 Feb 2019 22:14:33 +0000 (00:14 +0200)]
mmc: omap: fix the maximum timeout setting
[ Upstream commit
a6327b5e57fdc679c842588c3be046c0b39cc127 ]
When running OMAP1 kernel on QEMU, MMC access is annoyingly noisy:
MMC: CTO of 0xff and 0xfe cannot be used!
MMC: CTO of 0xff and 0xfe cannot be used!
MMC: CTO of 0xff and 0xfe cannot be used!
[ad inf.]
Emulator warnings appear to be valid. The TI document SPRU680 [1]
("OMAP5910 Dual-Core Processor MultiMedia Card/Secure Data Memory Card
(MMC/SD) Reference Guide") page 36 states that the maximum timeout is 253
cycles and "0xff and 0xfe cannot be used".
Fix by using 0xfd as the maximum timeout.
Tested using QEMU 2.5 (Siemens SX1 machine, OMAP310), and also checked on
real hardware using Palm TE (OMAP310), Nokia 770 (OMAP1710) and Nokia N810
(OMAP2420) that MMC works as before.
[1] http://www.ti.com/lit/ug/spru680/spru680.pdf
Fixes:
730c9b7e6630f ("[MMC] Add OMAP MMC host driver")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Qu Wenruo [Thu, 24 Jan 2019 23:55:27 +0000 (07:55 +0800)]
btrfs: qgroup: Make qgroup async transaction commit more aggressive
[ Upstream commit
f5fef4593653dfa2a865c485bb81415de51d5c99 ]
[BUG]
Btrfs qgroup will still hit EDQUOT under the following case:
$ dev=/dev/test/test
$ mnt=/mnt/btrfs
$ umount $mnt &> /dev/null
$ umount $dev &> /dev/null
$ mkfs.btrfs -f $dev
$ mount $dev $mnt -o nospace_cache
$ btrfs subv create $mnt/subv
$ btrfs quota enable $mnt
$ btrfs quota rescan -w $mnt
$ btrfs qgroup limit -e 1G $mnt/subv
$ fallocate -l 900M $mnt/subv/padding
$ sync
$ rm $mnt/subv/padding
# Hit EDQUOT
$ xfs_io -f -c "pwrite 0 512M" $mnt/subv/real_file
[CAUSE]
Since commit
a514d63882c3 ("btrfs: qgroup: Commit transaction in advance
to reduce early EDQUOT"), btrfs is not forced to commit transaction to
reclaim more quota space.
Instead, we just check pertrans metadata reservation against some
threshold and try to do asynchronously transaction commit.
However in above case, the pertrans metadata reservation is pretty small
thus it will never trigger asynchronous transaction commit.
[FIX]
Instead of only accounting pertrans metadata reservation, we calculate
how much free space we have, and if there isn't much free space left,
commit transaction asynchronously to try to free some space.
This may slow down the fs when we have less than 32M free qgroup space,
but should reduce a lot of false EDQUOT, so the cost should be
acceptable.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Aneesh Kumar K.V [Tue, 26 Feb 2019 04:39:34 +0000 (10:09 +0530)]
powerpc/hugetlb: Handle mmap_min_addr correctly in get_unmapped_area callback
[ Upstream commit
5330367fa300742a97e20e953b1f77f48392faae ]
After we ALIGN up the address we need to make sure we didn't overflow
and resulted in zero address. In that case, we need to make sure that
the returned address is greater than mmap_min_addr.
This fixes selftest va_128TBswitch --run-hugetlb reporting failures when
run as non root user for
mmap(-1, MAP_HUGETLB)
The bug is that a non-root user requesting address -1 will be given address 0
which will then fail, whereas they should have been given something else that
would have succeeded.
We also avoid the first mmap(-1, MAP_HUGETLB) returning NULL address as mmap address
with this change. So we think this is not a security issue, because it only affects
whether we choose an address below mmap_min_addr, not whether we
actually allow that address to be mapped. ie. there are existing capability
checks to prevent a user mapping below mmap_min_addr and those will still be
honoured even without this fix.
Fixes:
484837601d4d ("powerpc/mm: Add radix support for hugetlb")
Reviewed-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nicolas Boichat [Mon, 28 Jan 2019 09:43:01 +0000 (17:43 +0800)]
iommu/io-pgtable-arm-v7s: Only kmemleak_ignore L2 tables
[ Upstream commit
032ebd8548c9d05e8d2bdc7a7ec2fe29454b0ad0 ]
L1 tables are allocated with __get_dma_pages, and therefore already
ignored by kmemleak.
Without this, the kernel would print this error message on boot,
when the first L1 table is allocated:
[ 2.810533] kmemleak: Trying to color unknown object at 0xffffffd652388000 as Black
[ 2.818190] CPU: 5 PID: 39 Comm: kworker/5:0 Tainted: G S 4.19.16 #8
[ 2.831227] Workqueue: events deferred_probe_work_func
[ 2.836353] Call trace:
...
[ 2.852532] paint_ptr+0xa0/0xa8
[ 2.855750] kmemleak_ignore+0x38/0x6c
[ 2.859490] __arm_v7s_alloc_table+0x168/0x1f4
[ 2.863922] arm_v7s_alloc_pgtable+0x114/0x17c
[ 2.868354] alloc_io_pgtable_ops+0x3c/0x78
...
Fixes:
e5fc9753b1a8314 ("iommu/io-pgtable: Add ARMv7 short descriptor support")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sebastian Andrzej Siewior [Wed, 13 Feb 2019 16:14:42 +0000 (17:14 +0100)]
ARM: 8840/1: use a raw_spinlock_t in unwind
[ Upstream commit
74ffe79ae538283bbf7c155e62339f1e5c87b55a ]
Mostly unwind is done with irqs enabled however SLUB may call it with
irqs disabled while creating a new SLUB cache.
I had system freeze while loading a module which called
kmem_cache_create() on init. That means SLUB's __slab_alloc() disabled
interrupts and then
->new_slab_objects()
->new_slab()
->setup_object()
->setup_object_debug()
->init_tracking()
->set_track()
->save_stack_trace()
->save_stack_trace_tsk()
->walk_stackframe()
->unwind_frame()
->unwind_find_idx()
=>spin_lock_irqsave(&unwind_lock);
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Lubomir Rintel [Sun, 24 Feb 2019 11:58:02 +0000 (12:58 +0100)]
serial: 8250_pxa: honor the port number from devicetree
[ Upstream commit
fe9ed6d2483fda55465f32924fb15bce0fac3fac ]
Like the other OF-enabled drivers, use the port number from the firmware if
the devicetree specifies an alias:
aliases {
...
serial2 = &uart2; /* Should be ttyS2 */
}
This is how the deprecated pxa.c driver behaved, switching to 8250_pxa
messes up the numbering.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sai Prakash Ranjan [Mon, 25 Feb 2019 17:54:01 +0000 (10:54 -0700)]
coresight: etm4x: Add support to enable ETMv4.2
[ Upstream commit
5666dfd1d8a45a167f0d8b4ef47ea7f780b1f24a ]
SDM845 has ETMv4.2 and can use the existing etm4x driver.
But the current etm driver checks only for ETMv4.0 and
errors out for other etm4x versions. This patch adds this
missing support to enable SoC's with ETMv4x to use same
driver by checking only the ETM architecture major version
number.
Without this change, we get below error during etm probe:
/ # dmesg | grep etm
[ 6.660093] coresight-etm4x: probe of
7040000.etm failed with error -22
[ 6.666902] coresight-etm4x: probe of
7140000.etm failed with error -22
[ 6.673708] coresight-etm4x: probe of
7240000.etm failed with error -22
[ 6.680511] coresight-etm4x: probe of
7340000.etm failed with error -22
[ 6.687313] coresight-etm4x: probe of
7440000.etm failed with error -22
[ 6.694113] coresight-etm4x: probe of
7540000.etm failed with error -22
[ 6.700914] coresight-etm4x: probe of
7640000.etm failed with error -22
[ 6.707717] coresight-etm4x: probe of
7740000.etm failed with error -22
With this change, etm probe is successful:
/ # dmesg | grep etm
[ 6.659198] coresight-etm4x
7040000.etm: CPU0: ETM v4.2 initialized
[ 6.665848] coresight-etm4x
7140000.etm: CPU1: ETM v4.2 initialized
[ 6.672493] coresight-etm4x
7240000.etm: CPU2: ETM v4.2 initialized
[ 6.679129] coresight-etm4x
7340000.etm: CPU3: ETM v4.2 initialized
[ 6.685770] coresight-etm4x
7440000.etm: CPU4: ETM v4.2 initialized
[ 6.692403] coresight-etm4x
7540000.etm: CPU5: ETM v4.2 initialized
[ 6.699024] coresight-etm4x
7640000.etm: CPU6: ETM v4.2 initialized
[ 6.705646] coresight-etm4x
7740000.etm: CPU7: ETM v4.2 initialized
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nathan Chancellor [Tue, 26 Feb 2019 05:38:55 +0000 (22:38 -0700)]
powerpc/xmon: Fix opcode being uninitialized in print_insn_powerpc
[ Upstream commit
e7140639b1de65bba435a6bd772d134901141f86 ]
When building with -Wsometimes-uninitialized, Clang warns:
arch/powerpc/xmon/ppc-dis.c:157:7: warning: variable 'opcode' is used
uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
if (cpu_has_feature(CPU_FTRS_POWER9))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/xmon/ppc-dis.c:167:7: note: uninitialized use occurs here
if (opcode == NULL)
^~~~~~
arch/powerpc/xmon/ppc-dis.c:157:3: note: remove the 'if' if its
condition is always true
if (cpu_has_feature(CPU_FTRS_POWER9))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/xmon/ppc-dis.c:132:38: note: initialize the variable
'opcode' to silence this warning
const struct powerpc_opcode *opcode;
^
= NULL
1 warning generated.
This warning seems to make no sense on the surface because opcode is set
to NULL right below this statement. However, there is a comma instead of
semicolon to end the dialect assignment, meaning that the opcode
assignment only happens in the if statement. Properly terminate that
line so that Clang no longer warns.
Fixes:
5b102782c7f4 ("powerpc/xmon: Enable disassembly files (compilation changes)")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Masahiro Yamada [Fri, 22 Feb 2019 07:40:10 +0000 (16:40 +0900)]
kbuild: invoke syncconfig if include/config/auto.conf.cmd is missing
[ Upstream commit
9390dff66a52d1a60c6e517d8fa6cdbdffc83cb1 ]
If include/config/auto.conf.cmd is lost for some reasons, it is not
self-healing, so the top Makefile misses to run syncconfig.
Move include/config/auto.conf.cmd to the target side.
I used a pattern rule instead of a normal rule here although it is
a bit gross.
If the rule were written with a normal rule like this,
include/config/auto.conf \
include/config/auto.conf.cmd \
include/config/tristate.conf: $(KCONFIG_CONFIG)
$(Q)$(MAKE) -f $(srctree)/Makefile syncconfig
... syncconfig would be executed per target.
Using a pattern rule makes sure that syncconfig is executed just once
because Make assumes the recipe will create all of the targets.
Here is a quote from the GNU Make manual [1]:
"Pattern rules may have more than one target. Unlike normal rules,
this does not act as many different rules with the same prerequisites
and recipe. If a pattern rule has multiple targets, make knows that
the rule's recipe is responsible for making all of the targets. The
recipe is executed only once to make all the targets. When searching
for a pattern rule to match a target, the target patterns of a rule
other than the one that matches the target in need of a rule are
incidental: make worries only about giving a recipe and prerequisites
to the file presently in question. However, when this file's recipe is
run, the other targets are marked as having been updated themselves."
[1]: https://www.gnu.org/software/make/manual/html_node/Pattern-Intro.html
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Benjamin Block [Thu, 21 Feb 2019 09:18:00 +0000 (10:18 +0100)]
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
[ Upstream commit
1749ef00f7312679f76d5e9104c5d1e22a829038 ]
We had a test-report where, under memory pressure, adding LUNs to the
systems would fail (the tests add LUNs strictly in sequence):
[ 5525.853432] scsi 0:0:1:
1088045124: Direct-Access IBM
2107900 .148 PQ: 0 ANSI: 5
[ 5525.853826] scsi 0:0:1:
1088045124: alua: supports implicit TPGS
[ 5525.853830] scsi 0:0:1:
1088045124: alua: device naa.
6005076303ffd32700000000000044da port group 0 rel port 43
[ 5525.853931] sd 0:0:1:
1088045124: Attached scsi generic sg10 type 0
[ 5525.854075] sd 0:0:1:
1088045124: [sdk] Disabling DIF Type 1 protection
[ 5525.855495] sd 0:0:1:
1088045124: [sdk]
2097152 512-byte logical blocks: (1.07 GB/1.00 GiB)
[ 5525.855606] sd 0:0:1:
1088045124: [sdk] Write Protect is off
[ 5525.855609] sd 0:0:1:
1088045124: [sdk] Mode Sense: ed 00 00 08
[ 5525.855795] sd 0:0:1:
1088045124: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5525.857838] sdk: sdk1
[ 5525.859468] sd 0:0:1:
1088045124: [sdk] Attached SCSI disk
[ 5525.865073] sd 0:0:1:
1088045124: alua: transition timeout set to 60 seconds
[ 5525.865078] sd 0:0:1:
1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015070] sd 0:0:1:
1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015213] sd 0:0:1:
1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.587439] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
[ 5526.588562] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
Looking at the code of scsi_alloc_sdev(), and all the calling contexts,
there seems to be no reason to use GFP_ATMOIC here. All the different
call-contexts use a mutex at some point, and nothing in between that
requires no sleeping, as far as I could see. Additionally, the code that
later allocates the block queue for the device (scsi_mq_alloc_queue())
already uses GFP_KERNEL.
There are similar allocations in two other functions:
scsi_probe_and_add_lun(), and scsi_add_lun(),; that can also be done with
GFP_KERNEL.
Here is the contexts for the three functions so far:
scsi_alloc_sdev()
scsi_probe_and_add_lun()
scsi_sequential_lun_scan()
__scsi_scan_target()
scsi_scan_target()
mutex_lock()
scsi_scan_channel()
scsi_scan_host_selected()
mutex_lock()
scsi_report_lun_scan()
__scsi_scan_target()
...
__scsi_add_device()
mutex_lock()
__scsi_scan_target()
...
scsi_report_lun_scan()
...
scsi_get_host_dev()
mutex_lock()
scsi_probe_and_add_lun()
...
scsi_add_lun()
scsi_probe_and_add_lun()
...
So replace all these, and give them a bit of a better chance to succeed,
with more chances of reclaim.
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Alexey Kardashevskiy [Wed, 13 Feb 2019 03:38:18 +0000 (14:38 +1100)]
powerpc/powernv/ioda: Fix locked_vm counting for memory used by IOMMU tables
[ Upstream commit
11f5acce2fa43b015a8120fa7620fa4efd0a2952 ]
We store 2 multilevel tables in iommu_table - one for the hardware and
one with the corresponding userspace addresses. Before allocating
the tables, the iommu_table_group_ops::get_table_size() hook returns
the combined size of the two and VFIO SPAPR TCE IOMMU driver adjusts
the locked_vm counter correctly. When the table is actually allocated,
the amount of allocated memory is stored in iommu_table::it_allocated_size
and used to decrement the locked_vm counter when we release the memory
used by the table; .get_table_size() and .create_table() calculate it
independently but the result is expected to be the same.
However the allocator does not add the userspace table size to
.it_allocated_size so when we destroy the table because of VFIO PCI
unplug (i.e. VFIO container is gone but the userspace keeps running),
we decrement locked_vm by just a half of size of memory we are
releasing.
To make things worse, since we enabled on-demand allocation of
indirect levels, it_allocated_size contains only the amount of memory
actually allocated at the table creation time which can just be a
fraction. It is not a problem with incrementing locked_vm (as
get_table_size() value is used) but it is with decrementing.
As the result, we leak locked_vm and may not be able to allocate more
IOMMU tables after few iterations of hotplug/unplug.
This sets it_allocated_size in the pnv_pci_ioda2_ops::create_table()
hook to what pnv_pci_ioda2_get_table_size() returns so from now on we
have a single place which calculates the maximum memory a table can
occupy. The original meaning of it_allocated_size is somewhat lost now
though.
We do not ditch it_allocated_size whatsoever here and we do not call
get_table_size() from vfio_iommu_spapr_tce.c when decrementing
locked_vm as we may have multiple IOMMU groups per container and even
though they all are supposed to have the same get_table_size()
implementation, there is a small chance for failure or confusion.
Fixes:
090bad39b237 ("powerpc/powernv: Add indirect levels to it_userspace")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Paul Kocialkowski [Wed, 27 Feb 2019 06:51:36 +0000 (06:51 +0000)]
usb: chipidea: Grab the (legacy) USB PHY by phandle first
[ Upstream commit
68ef236274793066b9ba3154b16c0acc1c891e5c ]
According to the chipidea driver bindings, the USB PHY is specified via
the "phys" phandle node. However, this only takes effect for USB PHYs
that use the common PHY framework. For legacy USB PHYs, a simple lookup
based on the USB PHY type is done instead.
This does not play out well when more than one USB PHY is registered,
since the first registered PHY matching the type will always be
returned regardless of what the driver was bound to.
Fix this by looking up the PHY based on the "phys" phandle node.
Although generic PHYs are rather matched by their "phys-name" and not
the "phys" phandle directly, there is no helper for similar lookup on
legacy PHYs and it's probably not worth the effort to add it.
When no legacy USB PHY is found by phandle, fallback to grabbing any
registered USB2 PHY. This ensures backward compatibility if some users
were actually relying on this mechanism.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Eric Biggers [Sat, 23 Feb 2019 08:23:23 +0000 (00:23 -0800)]
crypto: cavium/zip - fix collision with generic cra_driver_name
[ Upstream commit
41798036430015ad45137db2d4c213cd77fd0251 ]
The cavium/zip implementation of the deflate compression algorithm is
incorrectly being registered under the generic driver name, which
prevents the generic implementation from being registered with the
crypto API when CONFIG_CRYPTO_DEV_CAVIUM_ZIP=y. Similarly the lzs
algorithm (which does not currently have a generic implementation...)
is incorrectly being registered as lzs-generic.
Fix the naming collision by adding a suffix "-cavium" to the
cra_driver_name of the cavium/zip algorithms.
Fixes:
640035a2dc55 ("crypto: zip - Add ThunderX ZIP driver core")
Cc: Mahipal Challa <mahipalreddy2006@gmail.com>
Cc: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Julia Lawall [Sat, 23 Feb 2019 13:20:39 +0000 (14:20 +0100)]
crypto: crypto4xx - add missing of_node_put after of_device_is_available
[ Upstream commit
8c2b43d2d85b48a97d2f8279278a4aac5b45f925 ]
Add an of_node_put when a tested device node is not available.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
identifier f;
local idexpression e;
expression x;
@@
e = f(...);
... when != of_node_put(e)
when != x = e
when != e = x
when any
if (<+...of_device_is_available(e)...+>) {
... when != of_node_put(e)
(
return e;
|
+ of_node_put(e);
return ...;
)
}
// </smpl>
Fixes:
5343e674f32fb ("crypto4xx: integrate ppc4xx-rng into crypto4xx")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Wen Yang [Fri, 22 Feb 2019 07:15:40 +0000 (15:15 +0800)]
mt76: fix a leaked reference by adding a missing of_node_put
[ Upstream commit
34e022d8b780a03902d82fb3997ba7c7b1f40c81 ]
The call to of_find_node_by_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/wireless/mediatek/mt76/eeprom.c:58:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:61:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:67:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:70:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:72:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Alexei Avshalom Lazar [Fri, 22 Feb 2019 14:21:05 +0000 (16:21 +0200)]
wil6210: check null pointer in _wil_cfg80211_merge_extra_ies
[ Upstream commit
de77a53c2d1e8fb3621e63e8e1f0f0c9a1a99ff7 ]
ies1 or ies2 might be null when code inside
_wil_cfg80211_merge_extra_ies access them.
Add explicit check for null and make sure ies1/ies2 are not
accessed in such a case.
spos might be null and be accessed inside
_wil_cfg80211_merge_extra_ies.
Add explicit check for null in the while condition statement
and make sure spos is not accessed in such a case.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Rafael J. Wysocki [Thu, 28 Feb 2019 19:56:27 +0000 (13:56 -0600)]
PCI/PME: Fix hotplug/sysfs remove deadlock in pcie_pme_remove()
[ Upstream commit
95c80bc6952b6a5badc7b702d23e5bf14d251e7c ]
Dongdong reported a deadlock triggered by a hotplug event during a sysfs
"remove" operation:
pciehp 0000:00:0c.0:pcie004: Slot(0-1): Link Up
# echo 1 > 0000:00:0c.0/remove
PME and hotplug share an MSI/MSI-X vector. The sysfs "remove" side is:
remove_store
pci_stop_and_remove_bus_device_locked
pci_lock_rescan_remove
pci_stop_and_remove_bus_device
...
pcie_pme_remove
pcie_pme_suspend
synchronize_irq # wait for hotplug IRQ handler
pci_unlock_rescan_remove
The hotplug side is:
pciehp_ist
pciehp_handle_presence_or_link_change
pciehp_configure_device
pci_lock_rescan_remove # wait for pci_unlock_rescan_remove()
INFO: task bash:10913 blocked for more than 120 seconds.
# ps -ax |grep D
PID TTY STAT TIME COMMAND
10913 ttyAMA0 Ds+ 0:00 -bash
14022 ? D 0:00 [irq/745-pciehp]
# cat /proc/14022/stack
__switch_to+0x94/0xd8
pci_lock_rescan_remove+0x20/0x28
pciehp_configure_device+0x30/0x140
pciehp_handle_presence_or_link_change+0x324/0x458
pciehp_ist+0x1dc/0x1e0
# cat /proc/10913/stack
__switch_to+0x94/0xd8
synchronize_irq+0x8c/0xc0
pcie_pme_suspend+0xa4/0x118
pcie_pme_remove+0x20/0x40
pcie_port_remove_service+0x3c/0x58
...
pcie_port_device_remove+0x2c/0x48
pcie_portdrv_remove+0x68/0x78
pci_device_remove+0x48/0x120
...
pci_stop_bus_device+0x84/0xc0
pci_stop_and_remove_bus_device_locked+0x24/0x40
remove_store+0xa4/0xb8
dev_attr_store+0x44/0x60
sysfs_kf_write+0x58/0x80
It is incorrect to call pcie_pme_suspend() from pcie_pme_remove() for two
reasons.
First, pcie_pme_suspend() calls synchronize_irq(), which will wait for the
native hotplug interrupt handler as well as for the PME one, because they
share one IRQ (as per the spec). That may deadlock if hotplug is signaled
while pcie_pme_remove() is running and the latter calls
pci_lock_rescan_remove() before the former.
Second, if pcie_pme_suspend() figures out that wakeup needs to be enabled
for the port, it will return without disabling the interrupt as expected by
pcie_pme_remove() which was overlooked by commit
c7b5a4e6e8fb ("PCI / PM:
Fix native PME handling during system suspend/resume").
To fix that, rework pcie_pme_remove() to disable the PME interrupt, clear
its status and prevent the PME worker function from re-enabling it before
calling free_irq() on it, which should be sufficient.
Fixes:
c7b5a4e6e8fb ("PCI / PM: Fix native PME handling during system suspend/resume")
Link: https://lore.kernel.org/linux-pci/c7697e7c-e1af-13e4-8491-0a3996e6ab5d@huawei.com
Reported-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bhelgaas: add URL and deadlock details from Dongdong]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tony Jones [Thu, 28 Feb 2019 01:55:32 +0000 (17:55 -0800)]
tools lib traceevent: Fix buffer overflow in arg_eval
[ Upstream commit
7c5b019e3a638a5a290b0ec020f6ca83d2ec2aaa ]
Fix buffer overflow observed when running perf test.
The overflow is when trying to evaluate "1ULL << (64 - 1)" which is
resulting in -
9223372036854775808 which overflows the 20 character
buffer.
If is possible this bug has been reported before but I still don't see
any fix checked in:
See: https://www.spinics.net/lists/linux-perf-users/msg07714.html
Reported-by: Michael Sartain <mikesart@fastmail.com>
Reported-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Tony Jones <tonyj@suse.de>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Fixes:
f7d82350e597 ("tools/events: Add files to create libtraceevent.a")
Link: http://lkml.kernel.org/r/20190228015532.8941-1-tonyj@suse.de
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Carlos Maiolino [Tue, 26 Feb 2019 10:51:50 +0000 (11:51 +0100)]
fs: fix guard_bio_eod to check for real EOD errors
[ Upstream commit
dce30ca9e3b676fb288c33c1f4725a0621361185 ]
guard_bio_eod() can truncate a segment in bio to allow it to do IO on
odd last sectors of a device.
It already checks if the IO starts past EOD, but it does not consider
the possibility of an IO request starting within device boundaries can
contain more than one segment past EOD.
In such cases, truncated_bytes can be bigger than PAGE_SIZE, and will
underflow bvec->bv_len.
Fix this by checking if truncated_bytes is lower than PAGE_SIZE.
This situation has been found on filesystems such as isofs and vfat,
which doesn't check the device size before mount, if the device is
smaller than the filesystem itself, a readahead on such filesystem,
which spans EOD, can trigger this situation, leading a call to
zero_user() with a wrong size possibly corrupting memory.
I didn't see any crash, or didn't let the system run long enough to
check if memory corruption will be hit somewhere, but adding
instrumentation to guard_bio_end() to check truncated_bytes size, was
enough to see the error.
The following script can trigger the error.
MNT=/mnt
IMG=./DISK.img
DEV=/dev/loop0
mkfs.vfat $IMG
mount $IMG $MNT
cp -R /etc $MNT &> /dev/null
umount $MNT
losetup -D
losetup --find --show --sizelimit
16247280 $IMG
mount $DEV $MNT
find $MNT -type f -exec cat {} + >/dev/null
Kudos to Eric Sandeen for coming up with the reproducer above
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
luojiajun [Fri, 1 Mar 2019 05:30:00 +0000 (00:30 -0500)]
jbd2: fix invalid descriptor block checksum
[ Upstream commit
6e876c3dd205d30b0db6850e97a03d75457df007 ]
In jbd2_journal_commit_transaction(), if we are in abort mode,
we may flush the buffer without setting descriptor block checksum
by goto start_journal_io. Then fs is mounted,
jbd2_descriptor_block_csum_verify() failed.
[ 271.379811] EXT4-fs (vdd): shut down requested (2)
[ 271.381827] Aborting journal on device vdd-8.
[ 271.597136] JBD2: Invalid checksum recovering block 22199 in log
[ 271.598023] JBD2: recovery failed
[ 271.598484] EXT4-fs (vdd): error loading journal
Fix this problem by keep setting descriptor block checksum if the
descriptor buffer is not NULL.
This checksum problem can be reproduced by xfstests generic/388.
Signed-off-by: luojiajun <luojiajun3@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Florian Westphal [Thu, 21 Feb 2019 16:09:31 +0000 (17:09 +0100)]
netfilter: conntrack: tcp: only close if RST matches exact sequence
[ Upstream commit
be0502a3f2e94211a8809a09ecbc3a017189b8fb ]
TCP resets cause instant transition from established to closed state
provided the reset is in-window. Endpoints that implement RFC 5961
require resets to match the next expected sequence number.
RST segments that are in-window (but that do not match RCV.NXT) are
ignored, and a "challenge ACK" is sent back.
Main problem for conntrack is that its a middlebox, i.e. whereas an end
host might have ACK'd SEQ (and would thus accept an RST with this
sequence number), conntrack might not have seen this ACK (yet).
Therefore we can't simply flag RSTs with non-exact match as invalid.
This updates RST processing as follows:
1. If the connection is in a state other than ESTABLISHED, nothing is
changed, RST is subject to normal in-window check.
2. If the RSTs sequence number either matches exactly RCV.NXT,
connection state moves to CLOSE.
3. The same applies if the RST sequence number aligns with a previous
packet in the same direction.
In all other cases, the connection remains in ESTABLISHED state.
If the normal-in-window check passes, the timeout will be lowered
to that of CLOSE.
If the peer sends a challenge ack, connection timeout will be reset.
If the challenge ACK triggers another RST (RST was valid after all),
this 2nd RST will match expected sequence and conntrack state changes to
CLOSE.
If no challenge ACK is received, the connection will time out after
CLOSE seconds (10 seconds by default), just like without this patch.
Packetdrill test case:
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0
0.100 < S 0:0(0) win 32792 <mss 1460,sackOK,nop,nop,nop,wscale 7>
0.100 > S. 0:0(0) ack 1 win 64240 <mss 1460,nop,nop,sackOK,nop,wscale 7>
0.200 < . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4
// Receive a segment.
0.210 < P. 1:1001(1000) ack 1 win 46
0.210 > . 1:1(0) ack 1001
// Application writes 1000 bytes.
0.250 write(4, ..., 1000) = 1000
0.250 > P. 1:1001(1000) ack 1001
// First reset, old sequence. Conntrack (correctly) considers this
// invalid due to failed window validation (regardless of this patch).
0.260 < R 2:2(0) ack 1001 win 260
// 2nd reset, but too far ahead sequence. Same: correctly handled
// as invalid.
0.270 < R
99990001:
99990001(0) ack 1001 win 260
// in-window, but not exact sequence.
// Current Linux kernels might reply with a challenge ack, and do not
// remove connection.
// Without this patch, conntrack state moves to CLOSE.
// With patch, timeout is lowered like CLOSE, but connection stays
// in ESTABLISHED state.
0.280 < R 1010:1010(0) ack 1001 win 260
// Expect challenge ACK
0.281 > . 1001:1001(0) ack 1001 win 501
// With or without this patch, RST will cause connection
// to move to CLOSE (sequence number matches)
// 0.282 < R 1001:1001(0) ack 1001 win 260
// ACK
0.300 < . 1001:1001(0) ack 1001 win 257
// more data could be exchanged here, connection
// is still established
// Client closes the connection.
0.610 < F. 1001:1001(0) ack 1001 win 260
0.650 > . 1001:1001(0) ack 1002
// Close the connection without reading outstanding data
0.700 close(4) = 0
// so one more reset. Will be deemed acceptable with patch as well:
// connection is already closing.
0.701 > R. 1001:1001(0) ack 1002 win 501
// End packetdrill test case.
With patch, this generates following conntrack events:
[NEW] 120 SYN_SENT src=10.0.2.1 dst=10.0.0.1 sport=5437 dport=80 [UNREPLIED]
[UPDATE] 60 SYN_RECV src=10.0.2.1 dst=10.0.0.1 sport=5437 dport=80
[UPDATE] 432000 ESTABLISHED src=10.0.2.1 dst=10.0.0.1 sport=5437 dport=80 [ASSURED]
[UPDATE] 120 FIN_WAIT src=10.0.2.1 dst=10.0.0.1 sport=5437 dport=80 [ASSURED]
[UPDATE] 60 CLOSE_WAIT src=10.0.2.1 dst=10.0.0.1 sport=5437 dport=80 [ASSURED]
[UPDATE] 10 CLOSE src=10.0.2.1 dst=10.0.0.1 sport=5437 dport=80 [ASSURED]
Without patch, first RST moves connection to close, whereas socket state
does not change until FIN is received.
[NEW] 120 SYN_SENT src=10.0.2.1 dst=10.0.0.1 sport=5141 dport=80 [UNREPLIED]
[UPDATE] 60 SYN_RECV src=10.0.2.1 dst=10.0.0.1 sport=5141 dport=80
[UPDATE] 432000 ESTABLISHED src=10.0.2.1 dst=10.0.0.1 sport=5141 dport=80 [ASSURED]
[UPDATE] 10 CLOSE src=10.0.2.1 dst=10.0.0.1 sport=5141 dport=80 [ASSURED]
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Li RongQing [Tue, 26 Feb 2019 09:13:56 +0000 (17:13 +0800)]
netfilter: nf_tables: check the result of dereferencing base_chain->stats
[ Upstream commit
a9f5e78c403d2d62ade4f4c85040efc85f4049b8 ]
Check the result of dereferencing base_chain->stats, instead of result
of this_cpu_ptr with NULL.
base_chain->stats maybe be changed to NULL when a chain is updated and a
new NULL counter can be attached.
And we do not need to check returning of this_cpu_ptr since
base_chain->stats is from percpu allocator if it is non-NULL,
this_cpu_ptr returns a valid value.
And fix two sparse error by replacing rcu_access_pointer and
rcu_dereference with READ_ONCE under rcu_read_lock.
Thanks for Eric's help to finish this patch.
Fixes:
009240940e84c1 ("netfilter: nf_tables: don't assume chain stats are set when jumplabel is set")
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yao Liu [Mon, 28 Jan 2019 11:47:28 +0000 (19:47 +0800)]
cifs: Fix NULL pointer dereference of devname
[ Upstream commit
68e2672f8fbd1e04982b8d2798dd318bf2515dd2 ]
There is a NULL pointer dereference of devname in strspn()
The oops looks something like:
CIFS: Attempting to mount (null)
BUG: unable to handle kernel NULL pointer dereference at
0000000000000000
...
RIP: 0010:strspn+0x0/0x50
...
Call Trace:
? cifs_parse_mount_options+0x222/0x1710 [cifs]
? cifs_get_volume_info+0x2f/0x80 [cifs]
cifs_setup_volume_info+0x20/0x190 [cifs]
cifs_get_volume_info+0x50/0x80 [cifs]
cifs_smb3_do_mount+0x59/0x630 [cifs]
? ida_alloc_range+0x34b/0x3d0
cifs_do_mount+0x11/0x20 [cifs]
mount_fs+0x52/0x170
vfs_kern_mount+0x6b/0x170
do_mount+0x216/0xdc0
ksys_mount+0x83/0xd0
__x64_sys_mount+0x25/0x30
do_syscall_64+0x65/0x220
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fix this by adding a NULL check on devname in cifs_parse_devname()
Signed-off-by: Yao Liu <yotta.liu@ucloud.cn>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Namjae Jeon [Tue, 22 Jan 2019 00:46:45 +0000 (09:46 +0900)]
cifs: Accept validate negotiate if server return NT_STATUS_NOT_SUPPORTED
[ Upstream commit
969ae8e8d4ee54c99134d3895f2adf96047f5bee ]
Old windows version or Netapp SMB server will return
NT_STATUS_NOT_SUPPORTED since they do not allow or implement
FSCTL_VALIDATE_NEGOTIATE_INFO. The client should accept the response
provided it's properly signed.
See
https://blogs.msdn.microsoft.com/openspecification/2012/06/28/smb3-secure-dialect-negotiation/
and
MS-SMB2 validate negotiate response processing:
https://msdn.microsoft.com/en-us/library/hh880630.aspx
Samba client had already handled it.
https://bugzilla.samba.org/attachment.cgi?id=13285&action=edit
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Chao Yu [Thu, 14 Feb 2019 16:08:25 +0000 (00:08 +0800)]
f2fs: fix to check inline_xattr_size boundary correctly
[ Upstream commit
500e0b28ecd3c5aade98f3c3a339d18dcb166bb6 ]
We use below condition to check inline_xattr_size boundary:
if (!F2FS_OPTION(sbi).inline_xattr_size ||
F2FS_OPTION(sbi).inline_xattr_size >=
DEF_ADDRS_PER_INODE -
F2FS_TOTAL_EXTRA_ATTR_SIZE -
DEF_INLINE_RESERVED_SIZE -
DEF_MIN_INLINE_SIZE)
There is there problems in that check:
- we should allow inline_xattr_size equaling to min size of inline
{data,dentry} area.
- F2FS_TOTAL_EXTRA_ATTR_SIZE and inline_xattr_size are based on
different size unit, previous one is 4 bytes, latter one is 1 bytes.
- DEF_MIN_INLINE_SIZE only indicate min size of inline data area,
however, we need to consider min size of inline dentry area as well,
minimal inline dentry should at least contain two entries: '.' and
'..', so that min inline_dentry size is 40 bytes.
.bitmap 1 * 1 = 1
.reserved 1 * 1 = 1
.dentry 11 * 2 = 22
.filename 8 * 2 = 16
total 40
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jason Cai (Xiang Feng) [Sun, 20 Jan 2019 14:39:13 +0000 (22:39 +0800)]
dm thin: add sanity checks to thin-pool and external snapshot creation
[ Upstream commit
70de2cbda8a5d788284469e755f8b097d339c240 ]
Invoking dm_get_device() twice on the same device path with different
modes is dangerous. Because in that case, upgrade_mode() will alloc a
new 'dm_dev' and free the old one, which may be referenced by a previous
caller. Dereferencing the dangling pointer will trigger kernel NULL
pointer dereference.
The following two cases can reproduce this issue. Actually, they are
invalid setups that must be disallowed, e.g.:
1. Creating a thin-pool with read_only mode, and the same device as
both metadata and data.
dmsetup create thinp --table \
"0
41943040 thin-pool /dev/vdb /dev/vdb 128 0 1 read_only"
BUG: unable to handle kernel NULL pointer dereference at
0000000000000080
...
Call Trace:
new_read+0xfb/0x110 [dm_bufio]
dm_bm_read_lock+0x43/0x190 [dm_persistent_data]
? kmem_cache_alloc_trace+0x15c/0x1e0
__create_persistent_data_objects+0x65/0x3e0 [dm_thin_pool]
dm_pool_metadata_open+0x8c/0xf0 [dm_thin_pool]
pool_ctr.cold.79+0x213/0x913 [dm_thin_pool]
? realloc_argv+0x50/0x70 [dm_mod]
dm_table_add_target+0x14e/0x330 [dm_mod]
table_load+0x122/0x2e0 [dm_mod]
? dev_status+0x40/0x40 [dm_mod]
ctl_ioctl+0x1aa/0x3e0 [dm_mod]
dm_ctl_ioctl+0xa/0x10 [dm_mod]
do_vfs_ioctl+0xa2/0x600
? handle_mm_fault+0xda/0x200
? __do_page_fault+0x26c/0x4f0
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x55/0x150
entry_SYSCALL_64_after_hwframe+0x44/0xa9
2. Creating a external snapshot using the same thin-pool device.
dmsetup create thinp --table \
"0
41943040 thin-pool /dev/vdc /dev/vdb 128 0 2 ignore_discard"
dmsetup message /dev/mapper/thinp 0 "create_thin 0"
dmsetup create snap --table \
"0 204800 thin /dev/mapper/thinp 0 /dev/mapper/thinp"
BUG: unable to handle kernel NULL pointer dereference at
0000000000000000
...
Call Trace:
? __alloc_pages_nodemask+0x13c/0x2e0
retrieve_status+0xa5/0x1f0 [dm_mod]
? dm_get_live_or_inactive_table.isra.7+0x20/0x20 [dm_mod]
table_status+0x61/0xa0 [dm_mod]
ctl_ioctl+0x1aa/0x3e0 [dm_mod]
dm_ctl_ioctl+0xa/0x10 [dm_mod]
do_vfs_ioctl+0xa2/0x600
ksys_ioctl+0x60/0x90
? ksys_write+0x4f/0xb0
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x55/0x150
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Jason Cai (Xiang Feng) <jason.cai@linux.alibaba.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Louis Taylor [Wed, 27 Feb 2019 22:25:15 +0000 (22:25 +0000)]
cifs: use correct format characters
[ Upstream commit
259594bea574e515a148171b5cd84ce5cbdc028a ]
When compiling with -Wformat, clang emits the following warnings:
fs/cifs/smb1ops.c:312:20: warning: format specifies type 'unsigned
short' but the argument has type 'unsigned int' [-Wformat]
tgt_total_cnt, total_in_tgt);
^~~~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:289:4: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->flags, ref->server_type);
^~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:289:16: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->flags, ref->server_type);
^~~~~~~~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:291:4: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->ref_flag, ref->path_consumed);
^~~~~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:291:19: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->ref_flag, ref->path_consumed);
^~~~~~~~~~~~~~~~~~
The types of these arguments are unconditionally defined, so this patch
updates the format character to the correct ones for ints and unsigned
ints.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Louis Taylor <louis@kragniz.eu>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Qian Cai [Tue, 5 Mar 2019 23:41:24 +0000 (15:41 -0800)]
page_poison: play nicely with KASAN
[ Upstream commit
4117992df66a26fa33908b4969e04801534baab1 ]
KASAN does not play well with the page poisoning (CONFIG_PAGE_POISONING).
It triggers false positives in the allocation path:
BUG: KASAN: use-after-free in memchr_inv+0x2ea/0x330
Read of size 8 at addr
ffff88881f800000 by task swapper/0
CPU: 0 PID: 0 Comm: swapper Not tainted 5.0.0-rc1+ #54
Call Trace:
dump_stack+0xe0/0x19a
print_address_description.cold.2+0x9/0x28b
kasan_report.cold.3+0x7a/0xb5
__asan_report_load8_noabort+0x19/0x20
memchr_inv+0x2ea/0x330
kernel_poison_pages+0x103/0x3d5
get_page_from_freelist+0x15e7/0x4d90
because KASAN has not yet unpoisoned the shadow page for allocation
before it checks memchr_inv() but only found a stale poison pattern.
Also, false positives in free path,
BUG: KASAN: slab-out-of-bounds in kernel_poison_pages+0x29e/0x3d5
Write of size 4096 at addr
ffff8888112cc000 by task swapper/0/1
CPU: 5 PID: 1 Comm: swapper/0 Not tainted 5.0.0-rc1+ #55
Call Trace:
dump_stack+0xe0/0x19a
print_address_description.cold.2+0x9/0x28b
kasan_report.cold.3+0x7a/0xb5
check_memory_region+0x22d/0x250
memset+0x28/0x40
kernel_poison_pages+0x29e/0x3d5
__free_pages_ok+0x75f/0x13e0
due to KASAN adds poisoned redzones around slab objects, but the page
poisoning needs to poison the whole page.
Link: http://lkml.kernel.org/r/20190114233405.67843-1-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Shuriyc Chu [Tue, 5 Mar 2019 23:41:56 +0000 (15:41 -0800)]
fs/file.c: initialize init_files.resize_wait
[ Upstream commit
5704a06810682683355624923547b41540e2801a ]
(Taken from https://bugzilla.kernel.org/show_bug.cgi?id=200647)
'get_unused_fd_flags' in kthread cause kernel crash. It works fine on
4.1, but causes crash after get 64 fds. It also cause crash on
ubuntu1404/1604/1804, centos7.5, and the crash messages are almost the
same.
The crash message on centos7.5 shows below:
start fd 61
start fd 62
start fd 63
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: __wake_up_common+0x2e/0x90
PGD 0
Oops: 0000 [#1] SMP
Modules linked in: test(OE) xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 tun bridge stp llc ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter devlink sunrpc kvm_intel kvm irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd sg ppdev pcspkr virtio_balloon parport_pc parport i2c_piix4 joydev ip_tables xfs libcrc32c sr_mod cdrom sd_mod crc_t10dif crct10dif_generic ata_generic pata_acpi virtio_scsi virtio_console virtio_net cirrus drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm crct10dif_pclmul crct10dif_common crc32c_intel drm ata_piix serio_raw libata virtio_pci virtio_ring i2c_core
virtio floppy dm_mirror dm_region_hash dm_log dm_mod
CPU: 2 PID: 1820 Comm: test_fd Kdump: loaded Tainted: G OE ------------ 3.10.0-862.3.3.el7.x86_64 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.10.2-0-g5f4c7b1-prebuilt.qemu-project.org 04/01/2014
task:
ffff8e92b9431fa0 ti:
ffff8e94247a0000 task.ti:
ffff8e94247a0000
RIP: 0010:__wake_up_common+0x2e/0x90
RSP: 0018:
ffff8e94247a2d18 EFLAGS:
00010086
RAX:
0000000000000000 RBX:
ffffffff9d09daa0 RCX:
0000000000000000
RDX:
0000000000000000 RSI:
0000000000000003 RDI:
ffffffff9d09daa0
RBP:
ffff8e94247a2d50 R08:
0000000000000000 R09:
ffff8e92b95dfda8
R10:
0000000000000000 R11:
0000000000000000 R12:
ffffffff9d09daa8
R13:
0000000000000003 R14:
0000000000000000 R15:
0000000000000003
FS:
0000000000000000(0000) GS:
ffff8e9434e80000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000000000000 CR3:
000000017c686000 CR4:
00000000000207e0
Call Trace:
__wake_up+0x39/0x50
expand_files+0x131/0x250
__alloc_fd+0x47/0x170
get_unused_fd_flags+0x30/0x40
test_fd+0x12a/0x1c0 [test]
kthread+0xd1/0xe0
ret_from_fork_nospec_begin+0x21/0x21
Code: 66 90 55 48 89 e5 41 57 41 89 f7 41 56 41 89 ce 41 55 41 54 49 89 fc 49 83 c4 08 53 48 83 ec 10 48 8b 47 08 89 55 cc 4c 89 45 d0 <48> 8b 08 49 39 c4 48 8d 78 e8 4c 8d 69 e8 75 08 eb 3b 4c 89 ef
RIP __wake_up_common+0x2e/0x90
RSP <
ffff8e94247a2d18>
CR2:
0000000000000000
This issue exists since CentOS 7.5 3.10.0-862 and CentOS 7.4
(3.10.0-693.21.1 ) is ok. Root cause: the item 'resize_wait' is not
initialized before being used.
Reported-by: Richard Zhang <zhang.zijian@h3c.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sahitya Tummala [Mon, 4 Feb 2019 08:06:53 +0000 (13:36 +0530)]
f2fs: do not use mutex lock in atomic context
[ Upstream commit
9083977dabf3833298ddcd40dee28687f1e6b483 ]
Fix below warning coming because of using mutex lock in atomic context.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:98
in_atomic(): 1, irqs_disabled(): 0, pid: 585, name: sh
Preemption disabled at: __radix_tree_preload+0x28/0x130
Call trace:
dump_backtrace+0x0/0x2b4
show_stack+0x20/0x28
dump_stack+0xa8/0xe0
___might_sleep+0x144/0x194
__might_sleep+0x58/0x8c
mutex_lock+0x2c/0x48
f2fs_trace_pid+0x88/0x14c
f2fs_set_node_page_dirty+0xd0/0x184
Do not use f2fs_radix_tree_insert() to avoid doing cond_resched() with
spin_lock() acquired.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jia Guo [Tue, 5 Mar 2019 23:41:41 +0000 (15:41 -0800)]
ocfs2: fix a panic problem caused by o2cb_ctl
[ Upstream commit
cc725ef3cb202ef2019a3c67c8913efa05c3cce6 ]
In the process of creating a node, it will cause NULL pointer
dereference in kernel if o2cb_ctl failed in the interval (mkdir,
o2cb_set_node_attribute(node_num)] in function o2cb_add_node.
The node num is initialized to 0 in function o2nm_node_group_make_item,
o2nm_node_group_drop_item will mistake the node number 0 for a valid
node number when we delete the node before the node number is set
correctly. If the local node number of the current host happens to be
0, cluster->cl_local_node will be set to O2NM_INVALID_NODE_NUM while
o2hb_thread still running. The panic stack is generated as follows:
o2hb_thread
\-o2hb_do_disk_heartbeat
\-o2hb_check_own_slot
|-slot = ®->hr_slots[o2nm_this_node()];
//o2nm_this_node() return O2NM_INVALID_NODE_NUM
We need to check whether the node number is set when we delete the node.
Link: http://lkml.kernel.org/r/133d8045-72cc-863e-8eae-5013f9f6bc51@huawei.com
Signed-off-by: Jia Guo <guojia12@huawei.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Acked-by: Jun Piao <piaojun@huawei.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <ge.changwei@h3c.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Qian Cai [Tue, 5 Mar 2019 23:42:03 +0000 (15:42 -0800)]
mm/slab.c: kmemleak no scan alien caches
[ Upstream commit
92d1d07daad65c300c7d0b68bbef8867e9895d54 ]
Kmemleak throws endless warnings during boot due to in
__alloc_alien_cache(),
alc = kmalloc_node(memsize, gfp, node);
init_arraycache(&alc->ac, entries, batch);
kmemleak_no_scan(ac);
Kmemleak does not track the array cache (alc->ac) but the alien cache
(alc) instead, so let it track the latter by lifting kmemleak_no_scan()
out of init_arraycache().
There is another place that calls init_arraycache(), but
alloc_kmem_cache_cpus() uses the percpu allocation where will never be
considered as a leak.
kmemleak: Found object by alias at 0xffff8007b9aa7e38
CPU: 190 PID: 1 Comm: swapper/0 Not tainted 5.0.0-rc2+ #2
Call trace:
dump_backtrace+0x0/0x168
show_stack+0x24/0x30
dump_stack+0x88/0xb0
lookup_object+0x84/0xac
find_and_get_object+0x84/0xe4
kmemleak_no_scan+0x74/0xf4
setup_kmem_cache_node+0x2b4/0x35c
__do_tune_cpucache+0x250/0x2d4
do_tune_cpucache+0x4c/0xe4
enable_cpucache+0xc8/0x110
setup_cpu_cache+0x40/0x1b8
__kmem_cache_create+0x240/0x358
create_cache+0xc0/0x198
kmem_cache_create_usercopy+0x158/0x20c
kmem_cache_create+0x50/0x64
fsnotify_init+0x58/0x6c
do_one_initcall+0x194/0x388
kernel_init_freeable+0x668/0x688
kernel_init+0x18/0x124
ret_from_fork+0x10/0x18
kmemleak: Object 0xffff8007b9aa7e00 (size 256):
kmemleak: comm "swapper/0", pid 1, jiffies
4294697137
kmemleak: min_count = 1
kmemleak: count = 0
kmemleak: flags = 0x1
kmemleak: checksum = 0
kmemleak: backtrace:
kmemleak_alloc+0x84/0xb8
kmem_cache_alloc_node_trace+0x31c/0x3a0
__kmalloc_node+0x58/0x78
setup_kmem_cache_node+0x26c/0x35c
__do_tune_cpucache+0x250/0x2d4
do_tune_cpucache+0x4c/0xe4
enable_cpucache+0xc8/0x110
setup_cpu_cache+0x40/0x1b8
__kmem_cache_create+0x240/0x358
create_cache+0xc0/0x198
kmem_cache_create_usercopy+0x158/0x20c
kmem_cache_create+0x50/0x64
fsnotify_init+0x58/0x6c
do_one_initcall+0x194/0x388
kernel_init_freeable+0x668/0x688
kernel_init+0x18/0x124
kmemleak: Not scanning unknown object at 0xffff8007b9aa7e38
CPU: 190 PID: 1 Comm: swapper/0 Not tainted 5.0.0-rc2+ #2
Call trace:
dump_backtrace+0x0/0x168
show_stack+0x24/0x30
dump_stack+0x88/0xb0
kmemleak_no_scan+0x90/0xf4
setup_kmem_cache_node+0x2b4/0x35c
__do_tune_cpucache+0x250/0x2d4
do_tune_cpucache+0x4c/0xe4
enable_cpucache+0xc8/0x110
setup_cpu_cache+0x40/0x1b8
__kmem_cache_create+0x240/0x358
create_cache+0xc0/0x198
kmem_cache_create_usercopy+0x158/0x20c
kmem_cache_create+0x50/0x64
fsnotify_init+0x58/0x6c
do_one_initcall+0x194/0x388
kernel_init_freeable+0x668/0x688
kernel_init+0x18/0x124
ret_from_fork+0x10/0x18
Link: http://lkml.kernel.org/r/20190129184518.39808-1-cai@lca.pw
Fixes:
1fe00d50a9e8 ("slab: factor out initialization of array cache")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Uladzislau Rezki (Sony) [Tue, 5 Mar 2019 23:45:59 +0000 (15:45 -0800)]
mm/vmalloc.c: fix kernel BUG at mm/vmalloc.c:512!
[ Upstream commit
afd07389d3f4933c7f7817a92fb5e053d59a3182 ]
One of the vmalloc stress test case triggers the kernel BUG():
<snip>
[60.562151] ------------[ cut here ]------------
[60.562154] kernel BUG at mm/vmalloc.c:512!
[60.562206] invalid opcode: 0000 [#1] PREEMPT SMP PTI
[60.562247] CPU: 0 PID: 430 Comm: vmalloc_test/0 Not tainted 4.20.0+ #161
[60.562293] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
[60.562351] RIP: 0010:alloc_vmap_area+0x36f/0x390
<snip>
it can happen due to big align request resulting in overflowing of
calculated address, i.e. it becomes 0 after ALIGN()'s fixup.
Fix it by checking if calculated address is within vstart/vend range.
Link: http://lkml.kernel.org/r/20190124115648.9433-2-urezki@gmail.com
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Garnier <thgarnie@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vlastimil Babka [Tue, 5 Mar 2019 23:46:50 +0000 (15:46 -0800)]
mm, mempolicy: fix uninit memory access
[ Upstream commit
2e25644e8da4ed3a27e7b8315aaae74660be72dc ]
Syzbot with KMSAN reports (excerpt):
==================================================================
BUG: KMSAN: uninit-value in mpol_rebind_policy mm/mempolicy.c:353 [inline]
BUG: KMSAN: uninit-value in mpol_rebind_mm+0x249/0x370 mm/mempolicy.c:384
CPU: 1 PID: 17420 Comm: syz-executor4 Not tainted 4.20.0-rc7+ #15
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x173/0x1d0 lib/dump_stack.c:113
kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:613
__msan_warning+0x82/0xf0 mm/kmsan/kmsan_instr.c:295
mpol_rebind_policy mm/mempolicy.c:353 [inline]
mpol_rebind_mm+0x249/0x370 mm/mempolicy.c:384
update_tasks_nodemask+0x608/0xca0 kernel/cgroup/cpuset.c:1120
update_nodemasks_hier kernel/cgroup/cpuset.c:1185 [inline]
update_nodemask kernel/cgroup/cpuset.c:1253 [inline]
cpuset_write_resmask+0x2a98/0x34b0 kernel/cgroup/cpuset.c:1728
...
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:204 [inline]
kmsan_internal_poison_shadow+0x92/0x150 mm/kmsan/kmsan.c:158
kmsan_kmalloc+0xa6/0x130 mm/kmsan/kmsan_hooks.c:176
kmem_cache_alloc+0x572/0xb90 mm/slub.c:2777
mpol_new mm/mempolicy.c:276 [inline]
do_mbind mm/mempolicy.c:1180 [inline]
kernel_mbind+0x8a7/0x31a0 mm/mempolicy.c:1347
__do_sys_mbind mm/mempolicy.c:1354 [inline]
As it's difficult to report where exactly the uninit value resides in
the mempolicy object, we have to guess a bit. mm/mempolicy.c:353
contains this part of mpol_rebind_policy():
if (!mpol_store_user_nodemask(pol) &&
nodes_equal(pol->w.cpuset_mems_allowed, *newmask))
"mpol_store_user_nodemask(pol)" is testing pol->flags, which I couldn't
ever see being uninitialized after leaving mpol_new(). So I'll guess
it's actually about accessing pol->w.cpuset_mems_allowed on line 354,
but still part of statement starting on line 353.
For w.cpuset_mems_allowed to be not initialized, and the nodes_equal()
reachable for a mempolicy where mpol_set_nodemask() is called in
do_mbind(), it seems the only possibility is a MPOL_PREFERRED policy
with empty set of nodes, i.e. MPOL_LOCAL equivalent, with MPOL_F_LOCAL
flag. Let's exclude such policies from the nodes_equal() check. Note
the uninit access should be benign anyway, as rebinding this kind of
policy is always a no-op. Therefore no actual need for stable
inclusion.
Link: http://lkml.kernel.org/r/a71997c3-e8ae-a787-d5ce-3db05768b27c@suse.cz
Link: http://lkml.kernel.org/r/73da3e9c-cc84-509e-17d9-0c434bb9967d@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: syzbot+b19c2dc2c990ea657a71@syzkaller.appspotmail.com
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Yisheng Xie <xieyisheng1@huawei.com>
Cc: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tetsuo Handa [Tue, 5 Mar 2019 23:46:47 +0000 (15:46 -0800)]
memcg: killed threads should not invoke memcg OOM killer
[ Upstream commit
7775face207922ea62a4e96b9cd45abfdc7b9840 ]
If a memory cgroup contains a single process with many threads
(including different process group sharing the mm) then it is possible
to trigger a race when the oom killer complains that there are no oom
elible tasks and complain into the log which is both annoying and
confusing because there is no actual problem. The race looks as
follows:
P1 oom_reaper P2
try_charge try_charge
mem_cgroup_out_of_memory
mutex_lock(oom_lock)
out_of_memory
oom_kill_process(P1,P2)
wake_oom_reaper
mutex_unlock(oom_lock)
oom_reap_task
mutex_lock(oom_lock)
select_bad_process # no victim
The problem is more visible with many threads.
Fix this by checking for fatal_signal_pending from
mem_cgroup_out_of_memory when the oom_lock is already held.
The oom bypass is safe because we do the same early in the try_charge
path already. The situation migh have changed in the mean time. It
should be safe to check for fatal_signal_pending and tsk_is_oom_victim
but for a better code readability abstract the current charge bypass
condition into should_force_charge and reuse it from that path. "
Link: http://lkml.kernel.org/r/01370f70-e1f6-ebe4-b95e-0df21a0bc15e@i-love.sakura.ne.jp
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tetsuo Handa [Tue, 5 Mar 2019 23:48:22 +0000 (15:48 -0800)]
mm,oom: don't kill global init via memory.oom.group
[ Upstream commit
d342a0b38674867ea67fde47b0e1e60ffe9f17a2 ]
Since setting global init process to some memory cgroup is technically
possible, oom_kill_memcg_member() must check it.
Tasks in /test1 are going to be killed due to memory.oom.group set
Memory cgroup out of memory: Killed process 1 (systemd) total-vm:43400kB, anon-rss:1228kB, file-rss:3992kB, shmem-rss:0kB
oom_reaper: reaped process 1 (systemd), now anon-rss:0kB, file-rss:0kB, shmem-rss:0kB
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000008b
#include <stdio.h>
#include <string.h>
#include <unistd.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
int main(int argc, char *argv[])
{
static char buffer[
10485760];
static int pipe_fd[2] = { EOF, EOF };
unsigned int i;
int fd;
char buf[64] = { };
if (pipe(pipe_fd))
return 1;
if (chdir("/sys/fs/cgroup/"))
return 1;
fd = open("cgroup.subtree_control", O_WRONLY);
write(fd, "+memory", 7);
close(fd);
mkdir("test1", 0755);
fd = open("test1/memory.oom.group", O_WRONLY);
write(fd, "1", 1);
close(fd);
fd = open("test1/cgroup.procs", O_WRONLY);
write(fd, "1", 1);
snprintf(buf, sizeof(buf) - 1, "%d", getpid());
write(fd, buf, strlen(buf));
close(fd);
snprintf(buf, sizeof(buf) - 1, "%lu", sizeof(buffer) * 5);
fd = open("test1/memory.max", O_WRONLY);
write(fd, buf, strlen(buf));
close(fd);
for (i = 0; i < 10; i++)
if (fork() == 0) {
char c;
close(pipe_fd[1]);
read(pipe_fd[0], &c, 1);
memset(buffer, 0, sizeof(buffer));
sleep(3);
_exit(0);
}
close(pipe_fd[0]);
close(pipe_fd[1]);
sleep(3);
return 0;
}
[ 37.052923][ T9185] a.out invoked oom-killer: gfp_mask=0xcc0(GFP_KERNEL), order=0, oom_score_adj=0
[ 37.056169][ T9185] CPU: 4 PID: 9185 Comm: a.out Kdump: loaded Not tainted 5.0.0-rc4-next-
20190131 #280
[ 37.059205][ T9185] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 04/13/2018
[ 37.062954][ T9185] Call Trace:
[ 37.063976][ T9185] dump_stack+0x67/0x95
[ 37.065263][ T9185] dump_header+0x51/0x570
[ 37.066619][ T9185] ? trace_hardirqs_on+0x3f/0x110
[ 37.068171][ T9185] ? _raw_spin_unlock_irqrestore+0x3d/0x70
[ 37.069967][ T9185] oom_kill_process+0x18d/0x210
[ 37.071515][ T9185] out_of_memory+0x11b/0x380
[ 37.072936][ T9185] mem_cgroup_out_of_memory+0xb6/0xd0
[ 37.074601][ T9185] try_charge+0x790/0x820
[ 37.076021][ T9185] mem_cgroup_try_charge+0x42/0x1d0
[ 37.077629][ T9185] mem_cgroup_try_charge_delay+0x11/0x30
[ 37.079370][ T9185] do_anonymous_page+0x105/0x5e0
[ 37.080939][ T9185] __handle_mm_fault+0x9cb/0x1070
[ 37.082485][ T9185] handle_mm_fault+0x1b2/0x3a0
[ 37.083819][ T9185] ? handle_mm_fault+0x47/0x3a0
[ 37.085181][ T9185] __do_page_fault+0x255/0x4c0
[ 37.086529][ T9185] do_page_fault+0x28/0x260
[ 37.087788][ T9185] ? page_fault+0x8/0x30
[ 37.088978][ T9185] page_fault+0x1e/0x30
[ 37.090142][ T9185] RIP: 0033:0x7f8b183aefe0
[ 37.091433][ T9185] Code: 20 f3 44 0f 7f 44 17 d0 f3 44 0f 7f 47 30 f3 44 0f 7f 44 17 c0 48 01 fa 48 83 e2 c0 48 39 d1 74 a3 66 0f 1f 84 00 00 00 00 00 <66> 44 0f 7f 01 66 44 0f 7f 41 10 66 44 0f 7f 41 20 66 44 0f 7f 41
[ 37.096917][ T9185] RSP: 002b:
00007fffc5d329e8 EFLAGS:
00010206
[ 37.098615][ T9185] RAX:
00000000006010e0 RBX:
0000000000000008 RCX:
0000000000c30000
[ 37.100905][ T9185] RDX:
00000000010010c0 RSI:
0000000000000000 RDI:
00000000006010e0
[ 37.103349][ T9185] RBP:
0000000000000000 R08:
00007f8b188f4740 R09:
0000000000000000
[ 37.105797][ T9185] R10:
00007fffc5d32420 R11:
00007f8b183aef40 R12:
0000000000000005
[ 37.108228][ T9185] R13:
0000000000000000 R14:
ffffffffffffffff R15:
0000000000000000
[ 37.110840][ T9185] memory: usage 51200kB, limit 51200kB, failcnt 125
[ 37.113045][ T9185] memory+swap: usage 0kB, limit 9007199254740988kB, failcnt 0
[ 37.115808][ T9185] kmem: usage 0kB, limit 9007199254740988kB, failcnt 0
[ 37.117660][ T9185] Memory cgroup stats for /test1: cache:0KB rss:49484KB rss_huge:30720KB shmem:0KB mapped_file:0KB dirty:0KB writeback:0KB inactive_anon:0KB active_anon:49700KB inactive_file:0KB active_file:0KB unevictable:0KB
[ 37.123371][ T9185] oom-kill:constraint=CONSTRAINT_NONE,nodemask=(null),cpuset=/,mems_allowed=0,oom_memcg=/test1,task_memcg=/test1,task=a.out,pid=9188,uid=0
[ 37.128158][ T9185] Memory cgroup out of memory: Killed process 9188 (a.out) total-vm:14456kB, anon-rss:10324kB, file-rss:504kB, shmem-rss:0kB
[ 37.132710][ T9185] Tasks in /test1 are going to be killed due to memory.oom.group set
[ 37.132833][ T54] oom_reaper: reaped process 9188 (a.out), now anon-rss:0kB, file-rss:0kB, shmem-rss:0kB
[ 37.135498][ T9185] Memory cgroup out of memory: Killed process 1 (systemd) total-vm:43400kB, anon-rss:1228kB, file-rss:3992kB, shmem-rss:0kB
[ 37.143434][ T9185] Memory cgroup out of memory: Killed process 9182 (a.out) total-vm:14456kB, anon-rss:76kB, file-rss:588kB, shmem-rss:0kB
[ 37.144328][ T54] oom_reaper: reaped process 1 (systemd), now anon-rss:0kB, file-rss:0kB, shmem-rss:0kB
[ 37.147585][ T9185] Memory cgroup out of memory: Killed process 9183 (a.out) total-vm:14456kB, anon-rss:6228kB, file-rss:512kB, shmem-rss:0kB
[ 37.157222][ T9185] Memory cgroup out of memory: Killed process 9184 (a.out) total-vm:14456kB, anon-rss:6228kB, file-rss:508kB, shmem-rss:0kB
[ 37.157259][ T9185] Memory cgroup out of memory: Killed process 9185 (a.out) total-vm:14456kB, anon-rss:6228kB, file-rss:512kB, shmem-rss:0kB
[ 37.157291][ T9185] Memory cgroup out of memory: Killed process 9186 (a.out) total-vm:14456kB, anon-rss:4180kB, file-rss:508kB, shmem-rss:0kB
[ 37.157306][ T54] oom_reaper: reaped process 9183 (a.out), now anon-rss:0kB, file-rss:0kB, shmem-rss:0kB
[ 37.157328][ T9185] Memory cgroup out of memory: Killed process 9187 (a.out) total-vm:14456kB, anon-rss:4180kB, file-rss:512kB, shmem-rss:0kB
[ 37.157452][ T9185] Memory cgroup out of memory: Killed process 9189 (a.out) total-vm:14456kB, anon-rss:6228kB, file-rss:512kB, shmem-rss:0kB
[ 37.158733][ T9185] Memory cgroup out of memory: Killed process 9190 (a.out) total-vm:14456kB, anon-rss:552kB, file-rss:512kB, shmem-rss:0kB
[ 37.160083][ T54] oom_reaper: reaped process 9186 (a.out), now anon-rss:0kB, file-rss:0kB, shmem-rss:0kB
[ 37.160187][ T54] oom_reaper: reaped process 9189 (a.out), now anon-rss:0kB, file-rss:0kB, shmem-rss:0kB
[ 37.206941][ T54] oom_reaper: reaped process 9185 (a.out), now anon-rss:0kB, file-rss:0kB, shmem-rss:0kB
[ 37.212300][ T9185] Memory cgroup out of memory: Killed process 9191 (a.out) total-vm:14456kB, anon-rss:4180kB, file-rss:512kB, shmem-rss:0kB
[ 37.212317][ T54] oom_reaper: reaped process 9190 (a.out), now anon-rss:0kB, file-rss:0kB, shmem-rss:0kB
[ 37.218860][ T9185] Memory cgroup out of memory: Killed process 9192 (a.out) total-vm:14456kB, anon-rss:1080kB, file-rss:512kB, shmem-rss:0kB
[ 37.227667][ T54] oom_reaper: reaped process 9192 (a.out), now anon-rss:0kB, file-rss:0kB, shmem-rss:0kB
[ 37.292323][ T9193] abrt-hook-ccpp (9193) used greatest stack depth: 10480 bytes left
[ 37.351843][ T1] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000008b
[ 37.354833][ T1] CPU: 7 PID: 1 Comm: systemd Kdump: loaded Not tainted 5.0.0-rc4-next-
20190131 #280
[ 37.357876][ T1] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 04/13/2018
[ 37.361685][ T1] Call Trace:
[ 37.363239][ T1] dump_stack+0x67/0x95
[ 37.365010][ T1] panic+0xfc/0x2b0
[ 37.366853][ T1] do_exit+0xd55/0xd60
[ 37.368595][ T1] do_group_exit+0x47/0xc0
[ 37.370415][ T1] get_signal+0x32a/0x920
[ 37.372449][ T1] ? _raw_spin_unlock_irqrestore+0x3d/0x70
[ 37.374596][ T1] do_signal+0x32/0x6e0
[ 37.376430][ T1] ? exit_to_usermode_loop+0x26/0x9b
[ 37.378418][ T1] ? prepare_exit_to_usermode+0xa8/0xd0
[ 37.380571][ T1] exit_to_usermode_loop+0x3e/0x9b
[ 37.382588][ T1] prepare_exit_to_usermode+0xa8/0xd0
[ 37.384594][ T1] ? page_fault+0x8/0x30
[ 37.386453][ T1] retint_user+0x8/0x18
[ 37.388160][ T1] RIP: 0033:0x7f42c06974a8
[ 37.389922][ T1] Code: Bad RIP value.
[ 37.391788][ T1] RSP: 002b:
00007ffc3effd388 EFLAGS:
00010213
[ 37.394075][ T1] RAX:
000000000000000e RBX:
00007ffc3effd390 RCX:
0000000000000000
[ 37.396963][ T1] RDX:
000000000000002a RSI:
00007ffc3effd390 RDI:
0000000000000004
[ 37.399550][ T1] RBP:
00007ffc3effd680 R08:
0000000000000000 R09:
0000000000000000
[ 37.402334][ T1] R10:
00000000ffffffff R11:
0000000000000246 R12:
0000000000000001
[ 37.404890][ T1] R13:
ffffffffffffffff R14:
0000000000000884 R15:
000056460b1ac3b0
Link: http://lkml.kernel.org/r/201902010336.x113a4EO027170@www262.sakura.ne.jp
Fixes:
3d8b38eb81cac813 ("mm, oom: introduce memory.oom.group")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Daniel Jordan [Tue, 5 Mar 2019 23:48:19 +0000 (15:48 -0800)]
mm, swap: bounds check swap_info array accesses to avoid NULL derefs
[ Upstream commit
c10d38cc8d3e43f946b6c2bf4602c86791587f30 ]
Dan Carpenter reports a potential NULL dereference in
get_swap_page_of_type:
Smatch complains that the NULL checks on "si" aren't consistent. This
seems like a real bug because we have not ensured that the type is
valid and so "si" can be NULL.
Add the missing check for NULL, taking care to use a read barrier to
ensure CPU1 observes CPU0's updates in the correct order:
CPU0 CPU1
alloc_swap_info() if (type >= nr_swapfiles)
swap_info[type] = p /* handle invalid entry */
smp_wmb() smp_rmb()
++nr_swapfiles p = swap_info[type]
Without smp_rmb, CPU1 might observe CPU0's write to nr_swapfiles before
CPU0's write to swap_info[type] and read NULL from swap_info[type].
Ying Huang noticed other places in swapfile.c don't order these reads
properly. Introduce swap_type_to_swap_info to encourage correct usage.
Use READ_ONCE and WRITE_ONCE to follow the Linux Kernel Memory Model
(see tools/memory-model/Documentation/explanation.txt).
This ordering need not be enforced in places where swap_lock is held
(e.g. si_swapinfo) because swap_lock serializes updates to nr_swapfiles
and the swap_info array.
Link: http://lkml.kernel.org/r/20190131024410.29859-1-daniel.m.jordan@oracle.com
Fixes:
ec8acf20afb8 ("swap: add per-partition lock for swapfile")
Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Qian Cai [Tue, 5 Mar 2019 23:49:46 +0000 (15:49 -0800)]
mm/page_ext.c: fix an imbalance with kmemleak
[ Upstream commit
0c81585499601acd1d0e1cbf424cabfaee60628c ]
After offlining a memory block, kmemleak scan will trigger a crash, as
it encounters a page ext address that has already been freed during
memory offlining. At the beginning in alloc_page_ext(), it calls
kmemleak_alloc(), but it does not call kmemleak_free() in
free_page_ext().
BUG: unable to handle kernel paging request at
ffff888453d00000
PGD
128a01067 P4D
128a01067 PUD
128a04067 PMD
47e09e067 PTE
800ffffbac2ff060
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
CPU: 1 PID: 1594 Comm: bash Not tainted 5.0.0-rc8+ #15
Hardware name: HP ProLiant DL180 Gen9/ProLiant DL180 Gen9, BIOS U20 10/25/2017
RIP: 0010:scan_block+0xb5/0x290
Code: 85 6e 01 00 00 48 b8 00 00 30 f5 81 88 ff ff 48 39 c3 0f 84 5b 01 00 00 48 89 d8 48 c1 e8 03 42 80 3c 20 00 0f 85 87 01 00 00 <4c> 8b 3b e8 f3 0c fa ff 4c 39 3d 0c 6b 4c 01 0f 87 08 01 00 00 4c
RSP: 0018:
ffff8881ec57f8e0 EFLAGS:
00010082
RAX:
0000000000000000 RBX:
ffff888453d00000 RCX:
ffffffffa61e5a54
RDX:
0000000000000000 RSI:
0000000000000008 RDI:
ffff888453d00000
RBP:
ffff8881ec57f920 R08:
fffffbfff4ed588d R09:
fffffbfff4ed588c
R10:
fffffbfff4ed588c R11:
ffffffffa76ac463 R12:
dffffc0000000000
R13:
ffff888453d00ff9 R14:
ffff8881f80cef48 R15:
ffff8881f80cef48
FS:
00007f6c0e3f8740(0000) GS:
ffff8881f7680000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
ffff888453d00000 CR3:
00000001c4244003 CR4:
00000000001606a0
Call Trace:
scan_gray_list+0x269/0x430
kmemleak_scan+0x5a8/0x10f0
kmemleak_write+0x541/0x6ca
full_proxy_write+0xf8/0x190
__vfs_write+0xeb/0x980
vfs_write+0x15a/0x4f0
ksys_write+0xd2/0x1b0
__x64_sys_write+0x73/0xb0
do_syscall_64+0xeb/0xaaa
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f6c0dad73b8
Code: 89 02 48 c7 c0 ff ff ff ff eb b3 0f 1f 80 00 00 00 00 f3 0f 1e fa 48 8d 05 65 63 2d 00 8b 00 85 c0 75 17 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 58 c3 0f 1f 80 00 00 00 00 41 54 49 89 d4 55
RSP: 002b:
00007ffd5b863cb8 EFLAGS:
00000246 ORIG_RAX:
0000000000000001
RAX:
ffffffffffffffda RBX:
0000000000000005 RCX:
00007f6c0dad73b8
RDX:
0000000000000005 RSI:
000055a9216e1710 RDI:
0000000000000001
RBP:
000055a9216e1710 R08:
000000000000000a R09:
00007ffd5b863840
R10:
000000000000000a R11:
0000000000000246 R12:
00007f6c0dda9780
R13:
0000000000000005 R14:
00007f6c0dda4740 R15:
0000000000000005
Modules linked in: nls_iso8859_1 nls_cp437 vfat fat kvm_intel kvm irqbypass efivars ip_tables x_tables xfs sd_mod ahci libahci igb i2c_algo_bit libata i2c_core dm_mirror dm_region_hash dm_log dm_mod efivarfs
CR2:
ffff888453d00000
---[ end trace
ccf646c7456717c5 ]---
Kernel panic - not syncing: Fatal exception
Shutting down cpus with NMI
Kernel Offset: 0x24c00000 from 0xffffffff81000000 (relocation range:
0xffffffff80000000-0xffffffffbfffffff)
---[ end Kernel panic - not syncing: Fatal exception ]---
Link: http://lkml.kernel.org/r/20190227173147.75650-1-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Peng Fan [Tue, 5 Mar 2019 23:49:50 +0000 (15:49 -0800)]
mm/cma.c: cma_declare_contiguous: correct err handling
[ Upstream commit
0d3bd18a5efd66097ef58622b898d3139790aa9d ]
In case cma_init_reserved_mem failed, need to free the memblock
allocated by memblock_reserve or memblock_alloc_range.
Quote Catalin's comments:
https://lkml.org/lkml/2019/2/26/482
Kmemleak is supposed to work with the memblock_{alloc,free} pair and it
ignores the memblock_reserve() as a memblock_alloc() implementation
detail. It is, however, tolerant to memblock_free() being called on
a sub-range or just a different range from a previous memblock_alloc().
So the original patch looks fine to me. FWIW:
Link: http://lkml.kernel.org/r/20190227144631.16708-1-peng.fan@nxp.com
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Qian Cai [Tue, 5 Mar 2019 23:50:11 +0000 (15:50 -0800)]
mm/sparse: fix a bad comparison
[ Upstream commit
d778015ac95bc036af73342c878ab19250e01fe1 ]
next_present_section_nr() could only return an unsigned number -1, so
just check it specifically where compilers will convert -1 to unsigned
if needed.
mm/sparse.c: In function 'sparse_init_nid':
mm/sparse.c:200:20: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
((section_nr >= 0) && \
^~
mm/sparse.c:478:2: note: in expansion of macro
'for_each_present_section_nr'
for_each_present_section_nr(pnum_begin, pnum) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~
mm/sparse.c:200:20: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
((section_nr >= 0) && \
^~
mm/sparse.c:497:2: note: in expansion of macro
'for_each_present_section_nr'
for_each_present_section_nr(pnum_begin, pnum) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~
mm/sparse.c: In function 'sparse_init':
mm/sparse.c:200:20: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
((section_nr >= 0) && \
^~
mm/sparse.c:520:2: note: in expansion of macro
'for_each_present_section_nr'
for_each_present_section_nr(pnum_begin + 1, pnum_end) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~
Link: http://lkml.kernel.org/r/20190228181839.86504-1-cai@lca.pw
Fixes:
c4e1be9ec113 ("mm, sparsemem: break out of loops early")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jiri Olsa [Tue, 5 Mar 2019 15:25:29 +0000 (16:25 +0100)]
perf c2c: Fix c2c report for empty numa node
[ Upstream commit
e34c940245437f36d2c492edd1f8237eff391064 ]
Ravi Bangoria reported that we fail with an empty NUMA node with the
following message:
$ lscpu
NUMA node0 CPU(s):
NUMA node1 CPU(s): 0-4
$ sudo ./perf c2c report
node/cpu topology bugFailed setup nodes
Fix this by detecting the empty node and keeping its CPU set empty.
Reported-by: Nageswara R Sastry <nasastry@in.ibm.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20190305152536.21035-2-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kairui Song [Wed, 6 Mar 2019 11:18:27 +0000 (19:18 +0800)]
x86/hyperv: Fix kernel panic when kexec on HyperV
[ Upstream commit
179fb36abb097976997f50733d5b122a29158cba ]
After commit
68bb7bfb7985 ("X86/Hyper-V: Enable IPI enlightenments"),
kexec fails with a kernel panic:
kexec_core: Starting new kernel
BUG: unable to handle kernel NULL pointer dereference at
0000000000000000
Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v3.0 03/02/2018
RIP: 0010:0xffffc9000001d000
Call Trace:
? __send_ipi_mask+0x1c6/0x2d0
? hv_send_ipi_mask_allbutself+0x6d/0xb0
? mp_save_irq+0x70/0x70
? __ioapic_read_entry+0x32/0x50
? ioapic_read_entry+0x39/0x50
? clear_IO_APIC_pin+0xb8/0x110
? native_stop_other_cpus+0x6e/0x170
? native_machine_shutdown+0x22/0x40
? kernel_kexec+0x136/0x156
That happens if hypercall based IPIs are used because the hypercall page is
reset very early upon kexec reboot, but kexec sends IPIs to stop CPUs,
which invokes the hypercall and dereferences the unusable page.
To fix his, reset hv_hypercall_pg to NULL before the page is reset to avoid
any misuse, IPI sending will fall back to the non hypercall based
method. This only happens on kexec / kdump so just setting the pointer to
NULL is good enough.
Fixes:
68bb7bfb7985 ("X86/Hyper-V: Enable IPI enlightenments")
Signed-off-by: Kairui Song <kasong@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: devel@linuxdriverproject.org
Link: https://lkml.kernel.org/r/20190306111827.14131-1-kasong@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Linus Torvalds [Wed, 6 Mar 2019 23:41:29 +0000 (15:41 -0800)]
iio: adc: fix warning in Qualcomm PM8xxx HK/XOADC driver
[ Upstream commit
e0f0ae838a25464179d37f355d763f9ec139fc15 ]
The pm8xxx_get_channel() implementation is unclear, and causes gcc to
suddenly generate odd warnings. The trigger for the warning (at least
for me) was the entirely unrelated commit
79a4e91d1bb2 ("device.h: Add
__cold to dev_<level> logging functions"), which apparently changes gcc
code generation in the caller function enough to cause this:
drivers/iio/adc/qcom-pm8xxx-xoadc.c: In function ‘pm8xxx_xoadc_probe’:
drivers/iio/adc/qcom-pm8xxx-xoadc.c:633:8: warning: ‘ch’ may be used uninitialized in this function [-Wmaybe-uninitialized]
ret = pm8xxx_read_channel_rsv(adc, ch, AMUX_RSV4,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
&read_nomux_rsv4, true);
~~~~~~~~~~~~~~~~~~~~~~~
drivers/iio/adc/qcom-pm8xxx-xoadc.c:426:27: note: ‘ch’ was declared here
struct pm8xxx_chan_info *ch;
^~
because gcc for some reason then isn't able to see that the termination
condition for the "for( )" loop in that function is also the condition
for returning NULL.
So it's not _actually_ uninitialized, but the function is admittedly
just unnecessarily oddly written.
Simplify and clarify the function, making gcc also see that it always
returns a valid initialized value.
Cc: Joe Perches <joe@perches.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xiang Chen [Thu, 28 Feb 2019 14:50:58 +0000 (22:50 +0800)]
scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
[ Upstream commit
4790595723d4b833b18c994973d39f9efb842887 ]
For internal IO and SMP IO, there is a time-out timer for them. In the
timer handler, it checks whether IO is done according to the flag
task->task_state_lock.
There is an issue which may cause system suspended: internal IO or SMP IO
is sent, but at that time because of hardware exception (such as inject
2Bit ECC error), so IO is not completed and also not timeout. But, at that
time, the SAS controller reset occurs to recover system. It will release
the resource and set the status of IO to be SAS_TASK_STATE_DONE, so when IO
timeout, it will never complete the completion of IO and wait for ever.
[ 729.123632] Call trace:
[ 729.126791] [<
ffff00000808655c>] __switch_to+0x94/0xa8
[ 729.133106] [<
ffff000008d96e98>] __schedule+0x1e8/0x7fc
[ 729.138975] [<
ffff000008d974e0>] schedule+0x34/0x8c
[ 729.144401] [<
ffff000008d9b000>] schedule_timeout+0x1d8/0x3cc
[ 729.150690] [<
ffff000008d98218>] wait_for_common+0xdc/0x1a0
[ 729.157101] [<
ffff000008d98304>] wait_for_completion+0x28/0x34
[ 729.165973] [<
ffff000000dcefb4>] hisi_sas_internal_task_abort+0x2a0/0x424 [hisi_sas_test_main]
[ 729.176447] [<
ffff000000dd18f4>] hisi_sas_abort_task+0x244/0x2d8 [hisi_sas_test_main]
[ 729.185258] [<
ffff000008971714>] sas_eh_handle_sas_errors+0x1c8/0x7b8
[ 729.192391] [<
ffff000008972774>] sas_scsi_recover_host+0x130/0x398
[ 729.199237] [<
ffff00000894d8a8>] scsi_error_handler+0x148/0x5c0
[ 729.206009] [<
ffff0000080f4118>] kthread+0x10c/0x138
[ 729.211563] [<
ffff0000080855dc>] ret_from_fork+0x10/0x18
To solve the issue, callback function task_done of those IOs need to be
called when on SAS controller reset.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
John Garry [Thu, 28 Feb 2019 14:51:00 +0000 (22:51 +0800)]
scsi: hisi_sas: Set PHY linkrate when disconnected
[ Upstream commit
efdcad62e7b8a02fcccc5ccca57806dce1482ac8 ]
When the PHY comes down, we currently do not set the negotiated linkrate:
root@(none)$ pwd
/sys/class/sas_phy/phy-0:0
root@(none)$ more enable
1
root@(none)$ more negotiated_linkrate
12.0 Gbit
root@(none)$ echo 0 > enable
root@(none)$ more negotiated_linkrate
12.0 Gbit
root@(none)$
This patch fixes the driver code to set it properly when the PHY comes
down.
If the PHY had been enabled, then set unknown; otherwise, flag as disabled.
The logical place to set the negotiated linkrate for this scenario is PHY
down routine, which is called from the PHY down ISR.
However, it is not possible to know if the PHY comes down due to PHY
disable or loss of link, as sas_phy.enabled member is not set until after
the transport disable routine is complete, which races with the PHY down
ISR.
As an imperfect solution, use sas_phy_data.enable as the flag to know if
the PHY is down due to disable. It's imperfect, as sas_phy_data is internal
to libsas.
I can't see another way without adding a new field to hisi_sas_phy and
managing it, or changing SCSI SAS transport.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Stanislav Fomichev [Wed, 6 Mar 2019 19:59:27 +0000 (11:59 -0800)]
libbpf: force fixdep compilation at the start of the build
[ Upstream commit
8e2688876c7f7073d925e1f150e86b8ed3338f52 ]
libbpf targets don't explicitly depend on fixdep target, so when
we do 'make -j$(nproc)', there is a high probability, that some
objects will be built before fixdep binary is available.
Fix this by running sub-make; this makes sure that fixdep dependency
is properly accounted for.
For the same issue in perf, see commit
abb26210a395 ("perf tools: Force
fixdep compilation at the start of the build").
Before:
$ rm -rf /tmp/bld; mkdir /tmp/bld; make -j$(nproc) O=/tmp/bld -C tools/lib/bpf/
Auto-detecting system features:
... libelf: [ on ]
... bpf: [ on ]
HOSTCC /tmp/bld/fixdep.o
CC /tmp/bld/libbpf.o
CC /tmp/bld/bpf.o
CC /tmp/bld/btf.o
CC /tmp/bld/nlattr.o
CC /tmp/bld/libbpf_errno.o
CC /tmp/bld/str_error.o
CC /tmp/bld/netlink.o
CC /tmp/bld/bpf_prog_linfo.o
CC /tmp/bld/libbpf_probes.o
CC /tmp/bld/xsk.o
HOSTLD /tmp/bld/fixdep-in.o
LINK /tmp/bld/fixdep
LD /tmp/bld/libbpf-in.o
LINK /tmp/bld/libbpf.a
LINK /tmp/bld/libbpf.so
LINK /tmp/bld/test_libbpf
$ head /tmp/bld/.libbpf.o.cmd
# cannot find fixdep (/usr/local/google/home/sdf/src/linux/xxx//fixdep)
# using basic dep data
/tmp/bld/libbpf.o: libbpf.c /usr/include/stdc-predef.h \
/usr/include/stdlib.h /usr/include/features.h \
/usr/include/x86_64-linux-gnu/sys/cdefs.h \
/usr/include/x86_64-linux-gnu/bits/wordsize.h \
/usr/include/x86_64-linux-gnu/gnu/stubs.h \
/usr/include/x86_64-linux-gnu/gnu/stubs-64.h \
/usr/lib/gcc/x86_64-linux-gnu/7/include/stddef.h \
After:
$ rm -rf /tmp/bld; mkdir /tmp/bld; make -j$(nproc) O=/tmp/bld -C tools/lib/bpf/
Auto-detecting system features:
... libelf: [ on ]
... bpf: [ on ]
HOSTCC /tmp/bld/fixdep.o
HOSTLD /tmp/bld/fixdep-in.o
LINK /tmp/bld/fixdep
CC /tmp/bld/libbpf.o
CC /tmp/bld/bpf.o
CC /tmp/bld/nlattr.o
CC /tmp/bld/btf.o
CC /tmp/bld/libbpf_errno.o
CC /tmp/bld/str_error.o
CC /tmp/bld/netlink.o
CC /tmp/bld/bpf_prog_linfo.o
CC /tmp/bld/libbpf_probes.o
CC /tmp/bld/xsk.o
LD /tmp/bld/libbpf-in.o
LINK /tmp/bld/libbpf.a
LINK /tmp/bld/libbpf.so
LINK /tmp/bld/test_libbpf
$ head /tmp/bld/.libbpf.o.cmd
cmd_/tmp/bld/libbpf.o := gcc -Wp,-MD,/tmp/bld/.libbpf.o.d -Wp,-MT,/tmp/bld/libbpf.o -g -Wall -DHAVE_LIBELF_MMAP_SUPPORT -DCOMPAT_NEED_REALLOCARRAY -Wbad-function-cast -Wdeclaration-after-statement -Wformat-security -Wformat-y2k -Winit-self -Wmissing-declarations -Wmissing-prototypes -Wnested-externs -Wno-system-headers -Wold-style-definition -Wpacked -Wredundant-decls -Wshadow -Wstrict-prototypes -Wswitch-default -Wswitch-enum -Wundef -Wwrite-strings -Wformat -Wstrict-aliasing=3 -Werror -Wall -fPIC -I. -I/usr/local/google/home/sdf/src/linux/tools/include -I/usr/local/google/home/sdf/src/linux/tools/arch/x86/include/uapi -I/usr/local/google/home/sdf/src/linux/tools/include/uapi -fvisibility=hidden -D"BUILD_STR(s)=$(pound)s" -c -o /tmp/bld/libbpf.o libbpf.c
source_/tmp/bld/libbpf.o := libbpf.c
deps_/tmp/bld/libbpf.o := \
/usr/include/stdc-predef.h \
/usr/include/stdlib.h \
/usr/include/features.h \
/usr/include/x86_64-linux-gnu/sys/cdefs.h \
/usr/include/x86_64-linux-gnu/bits/wordsize.h \
Fixes:
7c422f557266 ("tools build: Build fixdep helper from perf and basic libs")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Arnd Bergmann [Thu, 7 Mar 2019 15:52:24 +0000 (16:52 +0100)]
enic: fix build warning without CONFIG_CPUMASK_OFFSTACK
[ Upstream commit
43d281662fdb46750d49417559b71069f435298d ]
The enic driver relies on the CONFIG_CPUMASK_OFFSTACK feature to
dynamically allocate a struct member, but this is normally intended for
local variables.
Building with clang, I get a warning for a few locations that check the
address of the cpumask_var_t:
drivers/net/ethernet/cisco/enic/enic_main.c:122:22: error: address of array 'enic->msix[i].affinity_mask' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
As far as I can tell, the code is still correct, as the truth value of
the pointer is what we need in this configuration. To get rid of
the warning, use cpumask_available() instead of checking the
pointer directly.
Fixes:
322cf7e3a4e8 ("enic: assign affinity hint to interrupts")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nathan Chancellor [Thu, 7 Mar 2019 18:00:28 +0000 (11:00 -0700)]
net: stmmac: Avoid sometimes uninitialized Clang warnings
[ Upstream commit
df103170854e87124ee7bdd2bca64b178e653f97 ]
When building with -Wsometimes-uninitialized, Clang warns:
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:495:3: warning: variable 'ns' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:495:3: warning: variable 'ns' is used uninitialized whenever '&&' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:532:3: warning: variable 'ns' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:532:3: warning: variable 'ns' is used uninitialized whenever '&&' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:741:3: warning: variable 'sec_inc' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:741:3: warning: variable 'sec_inc' is used uninitialized whenever '&&' condition is false [-Wsometimes-uninitialized]
Clang is concerned with the use of stmmac_do_void_callback (which
stmmac_get_timestamp and stmmac_config_sub_second_increment wrap),
as it may fail to initialize these values if the if condition was ever
false (meaning the callbacks don't exist). It's not wrong because the
callbacks (get_timestamp and config_sub_second_increment respectively)
are the ones that initialize the variables. While it's unlikely that the
callbacks are ever going to disappear and make that condition false, we
can easily avoid this warning by zero initialize the variables.
Link: https://github.com/ClangBuiltLinux/linux/issues/384
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Christian Brauner [Fri, 8 Mar 2019 00:29:43 +0000 (16:29 -0800)]
sysctl: handle overflow for file-max
[ Upstream commit
32a5ad9c22852e6bd9e74bdec5934ef9d1480bc5 ]
Currently, when writing
echo
18446744073709551616 > /proc/sys/fs/file-max
/proc/sys/fs/file-max will overflow and be set to 0. That quickly
crashes the system.
This commit sets the max and min value for file-max. The max value is
set to long int. Any higher value cannot currently be used as the
percpu counters are long ints and not unsigned integers.
Note that the file-max value is ultimately parsed via
__do_proc_doulongvec_minmax(). This function does not report error when
min or max are exceeded. Which means if a value largen that long int is
written userspace will not receive an error instead the old value will be
kept. There is an argument to be made that this should be changed and
__do_proc_doulongvec_minmax() should return an error when a dedicated min
or max value are exceeded. However this has the potential to break
userspace so let's defer this to an RFC patch.
Link: http://lkml.kernel.org/r/20190107222700.15954-3-christian@brauner.io
Signed-off-by: Christian Brauner <christian@brauner.io>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Waiman Long <longman@redhat.com>
[christian@brauner.io: v4]
Link: http://lkml.kernel.org/r/20190210203943.8227-3-christian@brauner.io
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Luc Van Oostenryck [Fri, 8 Mar 2019 00:31:28 +0000 (16:31 -0800)]
include/linux/relay.h: fix percpu annotation in struct rchan
[ Upstream commit
62461ac2e5b6520b6d65fc6d7d7b4b8df4b848d8 ]
The percpu member of this structure is declared as:
struct ... ** __percpu member;
So its type is:
__percpu pointer to pointer to struct ...
But looking at how it's used, its type should be:
pointer to __percpu pointer to struct ...
and it should thus be declared as:
struct ... * __percpu *member;
So fix the placement of '__percpu' in the definition of this
structures.
This silents a few Sparse's warnings like:
warning: incorrect type in initializer (different address spaces)
expected void const [noderef] <asn:3> *__vpp_verify
got struct sched_domain **
Link: http://lkml.kernel.org/r/20190118144902.79065-1-luc.vanoostenryck@gmail.com
Fixes:
017c59c042d01 ("relay: Use per CPU constructs for the relay channel buffer pointers")
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Russell King [Fri, 1 Mar 2019 19:02:52 +0000 (11:02 -0800)]
gpio: gpio-omap: fix level interrupt idling
[ Upstream commit
d01849f7deba81f4959fd9e51bf20dbf46987d1c ]
Tony notes that the GPIO module does not idle when level interrupts are
in use, as the wakeup appears to get stuck.
After extensive investigation, it appears that the wakeup will only be
cleared if the interrupt status register is cleared while the interrupt
is enabled. However, we are currently clearing it with the interrupt
disabled for level-based interrupts.
It is acknowledged that this observed behaviour conflicts with a
statement in the TRM:
CAUTION
After servicing the interrupt, the status bit in the interrupt status
register (GPIOi.GPIO_IRQSTATUS_0 or GPIOi.GPIO_IRQSTATUS_1) must be
reset and the interrupt line released (by setting the corresponding
bit of the interrupt status register to 1) before enabling an
interrupt for the GPIO channel in the interrupt-enable register
(GPIOi.GPIO_IRQSTATUS_SET_0 or GPIOi.GPIO_IRQSTATUS_SET_1) to prevent
the occurrence of unexpected interrupts when enabling an interrupt
for the GPIO channel.
However, this does not appear to be a practical problem.
Further, as reported by Grygorii Strashko <grygorii.strashko@ti.com>,
the TI Android kernel tree has an earlier similar patch as "GPIO: OMAP:
Fix the sequence to clear the IRQ status" saying:
if the status is cleared after disabling the IRQ then sWAKEUP will not
be cleared and gates the module transition
When we unmask the level interrupt after the interrupt has been handled,
enable the interrupt and only then clear the interrupt. If the interrupt
is still pending, the hardware will re-assert the interrupt status.
Should the caution note in the TRM prove to be a problem, we could
use a clear-enable-clear sequence instead.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[tony@atomide.com: updated comments based on an earlier TI patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tonghao Zhang [Mon, 4 Mar 2019 08:27:15 +0000 (00:27 -0800)]
net/mlx5: Avoid panic when setting vport mac, getting vport config
[ Upstream commit
6e77c413e8e73d0f36b5358b601389d75ec4451c ]
If we try to set VFs mac address on a VF (not PF) net device,
the kernel will be crash. The commands are show as below:
$ echo 2 > /sys/class/net/$MLX_PF0/device/sriov_numvfs
$ ip link set $MLX_VF0 vf 0 mac 00:11:22:33:44:00
[exception RIP: mlx5_eswitch_set_vport_mac+41]
[
ffffb8b7079e3688] do_setlink at
ffffffff8f67f85b
[
ffffb8b7079e37a8] __rtnl_newlink at
ffffffff8f683778
[
ffffb8b7079e3b68] rtnl_newlink at
ffffffff8f683a63
[
ffffb8b7079e3b90] rtnetlink_rcv_msg at
ffffffff8f67d812
[
ffffb8b7079e3c10] netlink_rcv_skb at
ffffffff8f6b88ab
[
ffffb8b7079e3c60] netlink_unicast at
ffffffff8f6b808f
[
ffffb8b7079e3ca0] netlink_sendmsg at
ffffffff8f6b8412
[
ffffb8b7079e3d18] sock_sendmsg at
ffffffff8f6452f6
[
ffffb8b7079e3d30] ___sys_sendmsg at
ffffffff8f645860
[
ffffb8b7079e3eb0] __sys_sendmsg at
ffffffff8f647a38
[
ffffb8b7079e3f38] do_syscall_64 at
ffffffff8f00401b
[
ffffb8b7079e3f50] entry_SYSCALL_64_after_hwframe at
ffffffff8f80008c
and
[exception RIP: mlx5_eswitch_get_vport_config+12]
[
ffffa70607e57678] mlx5e_get_vf_config at
ffffffffc03c7f8f [mlx5_core]
[
ffffa70607e57688] do_setlink at
ffffffffbc67fa59
[
ffffa70607e577a8] __rtnl_newlink at
ffffffffbc683778
[
ffffa70607e57b68] rtnl_newlink at
ffffffffbc683a63
[
ffffa70607e57b90] rtnetlink_rcv_msg at
ffffffffbc67d812
[
ffffa70607e57c10] netlink_rcv_skb at
ffffffffbc6b88ab
[
ffffa70607e57c60] netlink_unicast at
ffffffffbc6b808f
[
ffffa70607e57ca0] netlink_sendmsg at
ffffffffbc6b8412
[
ffffa70607e57d18] sock_sendmsg at
ffffffffbc6452f6
[
ffffa70607e57d30] ___sys_sendmsg at
ffffffffbc645860
[
ffffa70607e57eb0] __sys_sendmsg at
ffffffffbc647a38
[
ffffa70607e57f38] do_syscall_64 at
ffffffffbc00401b
[
ffffa70607e57f50] entry_SYSCALL_64_after_hwframe at
ffffffffbc80008c
Fixes:
a8d70a054a718 ("net/mlx5: E-Switch, Disallow vlan/spoofcheck setup if not being esw manager")
Cc: Eli Cohen <eli@mellanox.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tonghao Zhang [Mon, 4 Mar 2019 08:27:16 +0000 (00:27 -0800)]
net/mlx5: Avoid panic when setting vport rate
[ Upstream commit
24319258660a84dd77f4be026a55b10a12524919 ]
If we try to set VFs rate on a VF (not PF) net device, the kernel
will be crash. The commands are show as below:
$ echo 2 > /sys/class/net/$MLX_PF0/device/sriov_numvfs
$ ip link set $MLX_VF0 vf 0 max_tx_rate 2 min_tx_rate 1
If not applied the first patch ("net/mlx5: Avoid panic when setting
vport mac, getting vport config"), the command:
$ ip link set $MLX_VF0 vf 0 rate 100
can also crash the kernel.
[ 1650.006388] RIP: 0010:mlx5_eswitch_set_vport_rate+0x1f/0x260 [mlx5_core]
[ 1650.007092] do_setlink+0x982/0xd20
[ 1650.007129] __rtnl_newlink+0x528/0x7d0
[ 1650.007374] rtnl_newlink+0x43/0x60
[ 1650.007407] rtnetlink_rcv_msg+0x2a2/0x320
[ 1650.007484] netlink_rcv_skb+0xcb/0x100
[ 1650.007519] netlink_unicast+0x17f/0x230
[ 1650.007554] netlink_sendmsg+0x2d2/0x3d0
[ 1650.007592] sock_sendmsg+0x36/0x50
[ 1650.007625] ___sys_sendmsg+0x280/0x2a0
[ 1650.007963] __sys_sendmsg+0x58/0xa0
[ 1650.007998] do_syscall_64+0x5b/0x180
[ 1650.009438] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes:
c9497c98901c ("net/mlx5: Add support for setting VF min rate")
Cc: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Douglas Anderson [Fri, 8 Mar 2019 19:32:04 +0000 (11:32 -0800)]
tracing: kdb: Fix ftdump to not sleep
[ Upstream commit
31b265b3baaf55f209229888b7ffea523ddab366 ]
As reported back in 2016-11 [1], the "ftdump" kdb command triggers a
BUG for "sleeping function called from invalid context".
kdb's "ftdump" command wants to call ring_buffer_read_prepare() in
atomic context. A very simple solution for this is to add allocation
flags to ring_buffer_read_prepare() so kdb can call it without
triggering the allocation error. This patch does that.
Note that in the original email thread about this, it was suggested
that perhaps the solution for kdb was to either preallocate the buffer
ahead of time or create our own iterator. I'm hoping that this
alternative of adding allocation flags to ring_buffer_read_prepare()
can be considered since it means I don't need to duplicate more of the
core trace code into "trace_kdb.c" (for either creating my own
iterator or re-preparing a ring allocator whose memory was already
allocated).
NOTE: another option for kdb is to actually figure out how to make it
reuse the existing ftrace_dump() function and totally eliminate the
duplication. This sounds very appealing and actually works (the "sr
z" command can be seen to properly dump the ftrace buffer). The
downside here is that ftrace_dump() fully consumes the trace buffer.
Unless that is changed I'd rather not use it because it means "ftdump
| grep xyz" won't be very useful to search the ftrace buffer since it
will throw away the whole trace on the first grep. A future patch to
dump only the last few lines of the buffer will also be hard to
implement.
[1] https://lkml.kernel.org/r/
20161117191605.GA21459@google.com
Link: http://lkml.kernel.org/r/20190308193205.213659-1-dianders@chromium.org
Reported-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Chao Yu [Tue, 12 Mar 2019 07:44:27 +0000 (15:44 +0800)]
f2fs: fix to avoid deadlock in f2fs_read_inline_dir()
[ Upstream commit
aadcef64b22f668c1a107b86d3521d9cac915c24 ]
As Jiqun Li reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=202883
sometimes, dead lock when make system call SYS_getdents64 with fsync() is
called by another process.
monkey running on android9.0
1. task 9785 held sbi->cp_rwsem and waiting lock_page()
2. task 10349 held mm_sem and waiting sbi->cp_rwsem
3. task 9709 held lock_page() and waiting mm_sem
so this is a dead lock scenario.
task stack is show by crash tools as following
crash_arm64> bt
ffffffc03c354080
PID: 9785 TASK:
ffffffc03c354080 CPU: 1 COMMAND: "RxIoScheduler-3"
>> #7 [
ffffffc01b50fac0] __lock_page at
ffffff80081b11e8
crash-arm64> bt 10349
PID: 10349 TASK:
ffffffc018b83080 CPU: 1 COMMAND: "BUGLY_ASYNC_UPL"
>> #3 [
ffffffc01f8cfa40] rwsem_down_read_failed at
ffffff8008a93afc
PC:
00000033 LR:
00000000 SP:
00000000 PSTATE:
ffffffffffffffff
crash-arm64> bt 9709
PID: 9709 TASK:
ffffffc03e7f3080 CPU: 1 COMMAND: "IntentService[A"
>> #3 [
ffffffc001e67850] rwsem_down_read_failed at
ffffff8008a93afc
>> #8 [
ffffffc001e67b80] el1_ia at
ffffff8008084fc4
PC:
ffffff8008274114 [compat_filldir64+120]
LR:
ffffff80083584d4 [f2fs_fill_dentries+448]
SP:
ffffffc001e67b80 PSTATE:
80400145
X29:
ffffffc001e67b80 X28:
0000000000000000 X27:
000000000000001a
X26:
00000000000093d7 X25:
ffffffc070d52480 X24:
0000000000000008
X23:
0000000000000028 X22:
00000000d43dfd60 X21:
ffffffc001e67e90
X20:
0000000000000011 X19:
ffffff80093a4000 X18:
0000000000000000
X17:
0000000000000000 X16:
0000000000000000 X15:
0000000000000000
X14:
ffffffffffffffff X13:
0000000000000008 X12:
0101010101010101
X11:
7f7f7f7f7f7f7f7f X10:
6a6a6a6a6a6a6a6a X9:
7f7f7f7f7f7f7f7f
X8:
0000000080808000 X7:
ffffff800827409c X6:
0000000080808000
X5:
0000000000000008 X4:
00000000000093d7 X3:
000000000000001a
X2:
0000000000000011 X1:
ffffffc070d52480 X0:
0000000000800238
>> #9 [
ffffffc001e67be0] f2fs_fill_dentries at
ffffff80083584d0
PC:
0000003c LR:
00000000 SP:
00000000 PSTATE:
000000d9
X12:
f48a02ff X11:
d4678960 X10:
d43dfc00 X9:
d4678ae4
X8:
00000058 X7:
d4678994 X6:
d43de800 X5:
000000d9
X4:
d43dfc0c X3:
d43dfc10 X2:
d46799c8 X1:
00000000
X0:
00001068
Below potential deadlock will happen between three threads:
Thread A Thread B Thread C
- f2fs_do_sync_file
- f2fs_write_checkpoint
- down_write(&sbi->node_change) -- 1)
- do_page_fault
- down_write(&mm->mmap_sem) -- 2)
- do_wp_page
- f2fs_vm_page_mkwrite
- getdents64
- f2fs_read_inline_dir
- lock_page -- 3)
- f2fs_sync_node_pages
- lock_page -- 3)
- __do_map_lock
- down_read(&sbi->node_change) -- 1)
- f2fs_fill_dentries
- dir_emit
- compat_filldir64
- do_page_fault
- down_read(&mm->mmap_sem) -- 2)
Since f2fs_readdir is protected by inode.i_rwsem, there should not be
any updates in inode page, we're safe to lookup dents in inode page
without its lock held, so taking off the lock to improve concurrency
of readdir and avoid potential deadlock.
Reported-by: Jiqun Li <jiqun.li@unisoc.com>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Chao Yu [Tue, 5 Mar 2019 11:32:26 +0000 (19:32 +0800)]
f2fs: fix to adapt small inline xattr space in __find_inline_xattr()
[ Upstream commit
2c28aba8b2e2a51749fa66e01b68e1cd5b53e022 ]
With below testcase, we will fail to find existed xattr entry:
1. mkfs.f2fs -O extra_attr -O flexible_inline_xattr /dev/zram0
2. mount -t f2fs -o inline_xattr_size=1 /dev/zram0 /mnt/f2fs/
3. touch /mnt/f2fs/file
4. setfattr -n "user.name" -v 0 /mnt/f2fs/file
5. getfattr -n "user.name" /mnt/f2fs/file
/mnt/f2fs/file: user.name: No such attribute
The reason is for inode which has very small inline xattr size,
__find_inline_xattr() will fail to traverse any entry due to first
entry may not be loaded from xattr node yet, later, we may skip to
check entire xattr datas in __find_xattr(), result in such wrong
condition.
This patch adds condition to check such case to avoid this issue.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Masahiro Yamada [Fri, 15 Feb 2019 04:04:26 +0000 (13:04 +0900)]
h8300: use cc-cross-prefix instead of hardcoding h8300-unknown-linux-
[ Upstream commit
fc2b47b55f17fd996f7a01975ce1c33c2f2513f6 ]
It believe it is a bad idea to hardcode a specific compiler prefix
that may or may not be installed on a user's system. It is annoying
when testing features that should not require compilers at all.
For example, mrproper, headers_install, etc. should work without
any compiler.
They look like follows on my machine.
$ make ARCH=h8300 mrproper
./scripts/gcc-version.sh: line 26: h8300-unknown-linux-gcc: command not found
./scripts/gcc-version.sh: line 27: h8300-unknown-linux-gcc: command not found
make: h8300-unknown-linux-gcc: Command not found
make: h8300-unknown-linux-gcc: Command not found
[ a bunch of the same error messages continue ]
$ make ARCH=h8300 headers_install
./scripts/gcc-version.sh: line 26: h8300-unknown-linux-gcc: command not found
./scripts/gcc-version.sh: line 27: h8300-unknown-linux-gcc: command not found
make: h8300-unknown-linux-gcc: Command not found
HOSTCC scripts/basic/fixdep
make: h8300-unknown-linux-gcc: Command not found
WRAP arch/h8300/include/generated/uapi/asm/kvm_para.h
[ snip ]
The solution is to delete this line, or to use cc-cross-prefix like
some architectures do. I chose the latter as a moderate fixup.
I added an alternative 'h8300-linux-' because it is available at:
https://mirrors.edge.kernel.org/pub/tools/crosstool/files/bin/x86_64/8.1.0/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Aurelien Aptel [Thu, 14 Mar 2019 17:44:16 +0000 (18:44 +0100)]
CIFS: fix POSIX lock leak and invalid ptr deref
[ Upstream commit
bc31d0cdcfbadb6258b45db97e93b1c83822ba33 ]
We have a customer reporting crashes in lock_get_status() with many
"Leaked POSIX lock" messages preceeding the crash.
Leaked POSIX lock on dev=0x0:0x56 ...
Leaked POSIX lock on dev=0x0:0x56 ...
Leaked POSIX lock on dev=0x0:0x56 ...
Leaked POSIX lock on dev=0x0:0x53 ...
Leaked POSIX lock on dev=0x0:0x53 ...
Leaked POSIX lock on dev=0x0:0x53 ...
Leaked POSIX lock on dev=0x0:0x53 ...
POSIX: fl_owner=
ffff8900e7b79380 fl_flags=0x1 fl_type=0x1 fl_pid=20709
Leaked POSIX lock on dev=0x0:0x4b ino...
Leaked locks on dev=0x0:0x4b ino=0xf911400000029:
POSIX: fl_owner=
ffff89f41c870e00 fl_flags=0x1 fl_type=0x1 fl_pid=19592
stack segment: 0000 [#1] SMP
Modules linked in: binfmt_misc msr tcp_diag udp_diag inet_diag unix_diag af_packet_diag netlink_diag rpcsec_gss_krb5 arc4 ecb auth_rpcgss nfsv4 md4 nfs nls_utf8 lockd grace cifs sunrpc ccm dns_resolver fscache af_packet iscsi_ibft iscsi_boot_sysfs vmw_vsock_vmci_transport vsock xfs libcrc32c sb_edac edac_core crct10dif_pclmul crc32_pclmul ghash_clmulni_intel drbg ansi_cprng vmw_balloon aesni_intel aes_x86_64 lrw gf128mul glue_helper ablk_helper cryptd joydev pcspkr vmxnet3 i2c_piix4 vmw_vmci shpchp fjes processor button ac btrfs xor raid6_pq sr_mod cdrom ata_generic sd_mod ata_piix vmwgfx crc32c_intel drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm serio_raw ahci libahci drm libata vmw_pvscsi sg dm_multipath dm_mod scsi_dh_rdac scsi_dh_emc scsi_dh_alua scsi_mod autofs4
Supported: Yes
CPU: 6 PID: 28250 Comm: lsof Not tainted 4.4.156-94.64-default #1
Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 04/05/2016
task:
ffff88a345f28740 ti:
ffff88c74005c000 task.ti:
ffff88c74005c000
RIP: 0010:[<
ffffffff8125dcab>] [<
ffffffff8125dcab>] lock_get_status+0x9b/0x3b0
RSP: 0018:
ffff88c74005fd90 EFLAGS:
00010202
RAX:
ffff89bde83e20ae RBX:
ffff89e870003d18 RCX:
0000000049534f50
RDX:
ffffffff81a3541f RSI:
ffffffff81a3544e RDI:
ffff89bde83e20ae
RBP:
0026252423222120 R08:
0000000020584953 R09:
000000000000ffff
R10:
0000000000000000 R11:
ffff88c74005fc70 R12:
ffff89e5ca7b1340
R13:
00000000000050e5 R14:
ffff89e870003d30 R15:
ffff89e5ca7b1340
FS:
00007fafd64be800(0000) GS:
ffff89f41fd00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000001c80018 CR3:
000000a522048000 CR4:
0000000000360670
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Stack:
0000000000000208 ffffffff81a3d6b6 ffff89e870003d30 ffff89e870003d18
ffff89e5ca7b1340 ffff89f41738d7c0 ffff89e870003d30 ffff89e5ca7b1340
ffffffff8125e08f 0000000000000000 ffff89bc22b67d00 ffff88c74005ff28
Call Trace:
[<
ffffffff8125e08f>] locks_show+0x2f/0x70
[<
ffffffff81230ad1>] seq_read+0x251/0x3a0
[<
ffffffff81275bbc>] proc_reg_read+0x3c/0x70
[<
ffffffff8120e456>] __vfs_read+0x26/0x140
[<
ffffffff8120e9da>] vfs_read+0x7a/0x120
[<
ffffffff8120faf2>] SyS_read+0x42/0xa0
[<
ffffffff8161cbc3>] entry_SYSCALL_64_fastpath+0x1e/0xb7
When Linux closes a FD (close(), close-on-exec, dup2(), ...) it calls
filp_close() which also removes all posix locks.
The lock struct is initialized like so in filp_close() and passed
down to cifs
...
lock.fl_type = F_UNLCK;
lock.fl_flags = FL_POSIX | FL_CLOSE;
lock.fl_start = 0;
lock.fl_end = OFFSET_MAX;
...
Note the FL_CLOSE flag, which hints the VFS code that this unlocking
is done for closing the fd.
filp_close()
locks_remove_posix(filp, id);
vfs_lock_file(filp, F_SETLK, &lock, NULL);
return filp->f_op->lock(filp, cmd, fl) => cifs_lock()
rc = cifs_setlk(file, flock, type, wait_flag, posix_lck, lock, unlock, xid);
rc = server->ops->mand_unlock_range(cfile, flock, xid);
if (flock->fl_flags & FL_POSIX && !rc)
rc = locks_lock_file_wait(file, flock)
Notice how we don't call locks_lock_file_wait() which does the
generic VFS lock/unlock/wait work on the inode if rc != 0.
If we are closing the handle, the SMB server is supposed to remove any
locks associated with it. Similarly, cifs.ko frees and wakes up any
lock and lock waiter when closing the file:
cifs_close()
cifsFileInfo_put(file->private_data)
/*
* Delete any outstanding lock records. We'll lose them when the file
* is closed anyway.
*/
down_write(&cifsi->lock_sem);
list_for_each_entry_safe(li, tmp, &cifs_file->llist->locks, llist) {
list_del(&li->llist);
cifs_del_lock_waiters(li);
kfree(li);
}
list_del(&cifs_file->llist->llist);
kfree(cifs_file->llist);
up_write(&cifsi->lock_sem);
So we can safely ignore unlocking failures in cifs_lock() if they
happen with the FL_CLOSE flag hint set as both the server and the
client take care of it during the actual closing.
This is not a proper fix for the unlocking failure but it's safe and
it seems to prevent the lock leakages and crashes the customer
experiences.
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Steve French <stfrench@microsoft.com>
Acked-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Razvan Stefanescu [Tue, 19 Mar 2019 13:20:35 +0000 (15:20 +0200)]
tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped
commit
69646d7a3689fbe1a65ae90397d22ac3f1b8d40f upstream.
In half-duplex operation, RX should be started after TX completes.
If DMA is used, there is a case when the DMA transfer completes but the
TX FIFO is not emptied, so the RX cannot be restarted just yet.
Use a boolean variable to store this state and rearm TX interrupt mask
to be signaled again that the transfer finished. In interrupt transmit
handler this variable is used to start RX. A warning message is generated
if RX is activated before TX fifo is cleared.
Fixes:
b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable
RX after TX is done")
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Razvan Stefanescu [Tue, 19 Mar 2019 13:20:34 +0000 (15:20 +0200)]
tty/serial: atmel: Add is_half_duplex helper
commit
f3040983132bf3477acd45d2452a906e67c2fec9 upstream.
Use a helper function to check that a port needs to use half duplex
communication, replacing several occurrences of multi-line bit checking.
Fixes:
b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
zhangyi (F) [Sat, 23 Mar 2019 15:56:01 +0000 (11:56 -0400)]
ext4: cleanup bh release code in ext4_ind_remove_space()
commit
5e86bdda41534e17621d5a071b294943cae4376e upstream.
Currently, we are releasing the indirect buffer where we are done with
it in ext4_ind_remove_space(), so we can see the brelse() and
BUFFER_TRACE() everywhere. It seems fragile and hard to read, and we
may probably forget to release the buffer some day. This patch cleans
up the code by putting of the code which releases the buffers to the
end of the function.
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jari Ruusu <jari.ruusu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon [Fri, 1 Mar 2019 13:28:00 +0000 (13:28 +0000)]
arm64: debug: Don't propagate UNKNOWN FAR into si_code for debug signals
commit
b9a4b9d084d978f80eb9210727c81804588b42ff upstream.
FAR_EL1 is UNKNOWN for all debug exceptions other than those caused by
taking a hardware watchpoint. Unfortunately, if a debug handler returns
a non-zero value, then we will propagate the UNKNOWN FAR value to
userspace via the si_addr field of the SIGTRAP siginfo_t.
Instead, let's set si_addr to take on the PC of the faulting instruction,
which we have available in the current pt_regs.
Cc: <stable@vger.kernel.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Wed, 3 Apr 2019 04:26:31 +0000 (06:26 +0200)]
Linux 4.19.33
Heikki Krogerus [Thu, 20 Sep 2018 11:23:45 +0000 (14:23 +0300)]
platform: x86: intel_cht_int33fe: Remove the old connections for the muxes
commit
148b0aa78e4e1077e38f928124bbc9c2d2d24006 upstream.
USB Type-C class driver now expects the muxes to be always
assigned to the ports and not controllers, so the
connections for the mux and fusb302 can be removed.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Thu, 20 Sep 2018 11:23:44 +0000 (14:23 +0300)]
usb: typec: class: Don't use port parent for getting mux handles
commit
23481121c81d984193edf1532f5e123637e50903 upstream.
It is not possible to use the parent of the port device when
requesting mux handles as the parent may be a multiport USB
Type-C or PD controller. The muxes must be assigned to the
ports, not the controllers.
This will also move the requesting of the muxes after the
port device is initialized.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Thu, 20 Sep 2018 11:23:43 +0000 (14:23 +0300)]
platform: x86: intel_cht_int33fe: Add connections for the USB Type-C port
commit
495965a1002a0b301bf4fbfd1aed3233f3e7db1b upstream.
Assigning the mux to the USB Type-C port on top of fusb302.
That will prepare this driver for the change in the USB
Type-C class code, where the class driver will assume the
muxes to be always assigned to the ports and not the
controllers.
Once the USB Type-C class driver has been updated, the
connections between the mux and fusb302 can be dropped.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Thu, 20 Sep 2018 11:23:42 +0000 (14:23 +0300)]
platform: x86: intel_cht_int33fe: Add connection for the DP alt mode
commit
78d2b54b134ea6059e2b1554ad53fab2300a4cc6 upstream.
Adding a connection for the DisplayPort alternate mode.
PI3USB30532 is used for muxing the port to DisplayPort on
CHT platforms. The connection allows the alternate mode
device to get handle to the mux, and therefore make it
possible to use the USB Type-C connector as DisplayPort.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Thu, 20 Sep 2018 11:23:41 +0000 (14:23 +0300)]
platform: x86: intel_cht_int33fe: Register all connections at once
commit
140a4ec4adddda615b4e8e8055ca37a30c7fe5e8 upstream.
We can register all device connection descriptors with a
single call to device_connections_add().
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Thu, 20 Sep 2018 11:23:40 +0000 (14:23 +0300)]
drivers: base: Helpers for adding device connection descriptions
commit
cd7753d371388e712e3ee52b693459f9b71aaac2 upstream.
Introducing helpers for adding and removing multiple device
connection descriptions at once.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xu Yu [Thu, 21 Mar 2019 10:00:35 +0000 (18:00 +0800)]
bpf: do not restore dst_reg when cur_state is freed
commit
0803278b0b4d8eeb2b461fb698785df65a725d9e upstream.
Syzkaller hit 'KASAN: use-after-free Write in sanitize_ptr_alu' bug.
Call trace:
dump_stack+0xbf/0x12e
print_address_description+0x6a/0x280
kasan_report+0x237/0x360
sanitize_ptr_alu+0x85a/0x8d0
adjust_ptr_min_max_vals+0x8f2/0x1ca0
adjust_reg_min_max_vals+0x8ed/0x22e0
do_check+0x1ca6/0x5d00
bpf_check+0x9ca/0x2570
bpf_prog_load+0xc91/0x1030
__se_sys_bpf+0x61e/0x1f00
do_syscall_64+0xc8/0x550
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fault injection trace:
kfree+0xea/0x290
free_func_state+0x4a/0x60
free_verifier_state+0x61/0xe0
push_stack+0x216/0x2f0 <- inject failslab
sanitize_ptr_alu+0x2b1/0x8d0
adjust_ptr_min_max_vals+0x8f2/0x1ca0
adjust_reg_min_max_vals+0x8ed/0x22e0
do_check+0x1ca6/0x5d00
bpf_check+0x9ca/0x2570
bpf_prog_load+0xc91/0x1030
__se_sys_bpf+0x61e/0x1f00
do_syscall_64+0xc8/0x550
entry_SYSCALL_64_after_hwframe+0x49/0xbe
When kzalloc() fails in push_stack(), free_verifier_state() will free
current verifier state. As push_stack() returns, dst_reg was restored
if ptr_is_dst_reg is false. However, as member of the cur_state,
dst_reg is also freed, and error occurs when dereferencing dst_reg.
Simply fix it by testing ret of push_stack() before restoring dst_reg.
Fixes:
979d63d50c0c ("bpf: prevent out of bounds speculation on pointer arithmetic")
Signed-off-by: Xu Yu <xuyu@linux.alibaba.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gao Xiang [Thu, 28 Mar 2019 20:14:58 +0000 (04:14 +0800)]
staging: erofs: keep corrupted fs from crashing kernel in erofs_readdir()
commit
33bac912840fe64dbc15556302537dc6a17cac63 upstream.
After commit
419d6efc50e9, kernel cannot be crashed in the namei
path. However, corrupted nameoff can do harm in the process of
readdir for scenerios without dm-verity as well. Fix it now.
Fixes:
3aa8ec716e52 ("staging: erofs: add directory operations")
Cc: <stable@vger.kernel.org> # 4.19+
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gao Xiang [Mon, 25 Mar 2019 03:40:07 +0000 (11:40 +0800)]
staging: erofs: fix error handling when failed to read compresssed data
commit
b6391ac73400eff38377a4a7364bd3df5efb5178 upstream.
Complete read error handling paths for all three kinds of
compressed pages:
1) For cache-managed pages, PG_uptodate will be checked since
read_endio will unlock and SetPageUptodate for these pages;
2) For inplaced pages, read_endio cannot SetPageUptodate directly
since it should be used to mark the final decompressed data,
PG_error will be set with page locked for IO error instead;
3) For staging pages, PG_error is used, which is similar to
what we do for inplaced pages.
Fixes:
3883a79abd02 ("staging: erofs: introduce VLE decompression support")
Cc: <stable@vger.kernel.org> # 4.19+
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Christopherson [Thu, 7 Mar 2019 23:43:02 +0000 (15:43 -0800)]
KVM: x86: Emulate MSR_IA32_ARCH_CAPABILITIES on AMD hosts
commit
0cf9135b773bf32fba9dd8e6699c1b331ee4b749 upstream.
The CPUID flag ARCH_CAPABILITIES is unconditioinally exposed to host
userspace for all x86 hosts, i.e. KVM advertises ARCH_CAPABILITIES
regardless of hardware support under the pretense that KVM fully
emulates MSR_IA32_ARCH_CAPABILITIES. Unfortunately, only VMX hosts
handle accesses to MSR_IA32_ARCH_CAPABILITIES (despite KVM_GET_MSRS
also reporting MSR_IA32_ARCH_CAPABILITIES for all hosts).
Move the MSR_IA32_ARCH_CAPABILITIES handling to common x86 code so
that it's emulated on AMD hosts.
Fixes:
1eaafe91a0df4 ("kvm: x86: IA32_ARCH_CAPABILITIES is always supported")
Cc: stable@vger.kernel.org
Reported-by: Xiaoyao Li <xiaoyao.li@linux.intel.com>
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Christopherson [Tue, 12 Mar 2019 03:01:05 +0000 (20:01 -0700)]
KVM: x86: update %rip after emulating IO
commit
45def77ebf79e2e8942b89ed79294d97ce914fa0 upstream.
Most (all?) x86 platforms provide a port IO based reset mechanism, e.g.
OUT 92h or CF9h. Userspace may emulate said mechanism, i.e. reset a
vCPU in response to KVM_EXIT_IO, without explicitly announcing to KVM
that it is doing a reset, e.g. Qemu jams vCPU state and resumes running.
To avoid corruping %rip after such a reset, commit
0967b7bf1c22 ("KVM:
Skip pio instruction when it is emulated, not executed") changed the
behavior of PIO handlers, i.e. today's "fast" PIO handling to skip the
instruction prior to exiting to userspace. Full emulation doesn't need
such tricks becase re-emulating the instruction will naturally handle
%rip being changed to point at the reset vector.
Updating %rip prior to executing to userspace has several drawbacks:
- Userspace sees the wrong %rip on the exit, e.g. if PIO emulation
fails it will likely yell about the wrong address.
- Single step exits to userspace for are effectively dropped as
KVM_EXIT_DEBUG is overwritten with KVM_EXIT_IO.
- Behavior of PIO emulation is different depending on whether it
goes down the fast path or the slow path.
Rather than skip the PIO instruction before exiting to userspace,
snapshot the linear %rip and cancel PIO completion if the current
value does not match the snapshot. For a 64-bit vCPU, i.e. the most
common scenario, the snapshot and comparison has negligible overhead
as VMCS.GUEST_RIP will be cached regardless, i.e. there is no extra
VMREAD in this case.
All other alternatives to snapshotting the linear %rip that don't
rely on an explicit reset announcenment suffer from one corner case
or another. For example, canceling PIO completion on any write to
%rip fails if userspace does a save/restore of %rip, and attempting to
avoid that issue by canceling PIO only if %rip changed then fails if PIO
collides with the reset %rip. Attempting to zero in on the exact reset
vector won't work for APs, which means adding more hooks such as the
vCPU's MP_STATE, and so on and so forth.
Checking for a linear %rip match technically suffers from corner cases,
e.g. userspace could theoretically rewrite the underlying code page and
expect a different instruction to execute, or the guest hardcodes a PIO
reset at 0xfffffff0, but those are far, far outside of what can be
considered normal operation.
Fixes:
432baf60eee3 ("KVM: VMX: use kvm_fast_pio_in for handling IN I/O")
Cc: <stable@vger.kernel.org>
Reported-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Christopherson [Fri, 15 Feb 2019 20:48:39 +0000 (12:48 -0800)]
KVM: Reject device ioctls from processes other than the VM's creator
commit
ddba91801aeb5c160b660caed1800eb3aef403f8 upstream.
KVM's API requires thats ioctls must be issued from the same process
that created the VM. In other words, userspace can play games with a
VM's file descriptors, e.g. fork(), SCM_RIGHTS, etc..., but only the
creator can do anything useful. Explicitly reject device ioctls that
are issued by a process other than the VM's creator, and update KVM's
API documentation to extend its requirements to device ioctls.
Fixes:
852b6d57dc7f ("kvm: add device control API")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Tue, 26 Mar 2019 16:36:06 +0000 (17:36 +0100)]
x86/smp: Enforce CONFIG_HOTPLUG_CPU when SMP=y
commit
bebd024e4815b1a170fcd21ead9c2222b23ce9e6 upstream.
The SMT disable 'nosmt' command line argument is not working properly when
CONFIG_HOTPLUG_CPU is disabled. The teardown of the sibling CPUs which are
required to be brought up due to the MCE issues, cannot work. The CPUs are
then kept in a half dead state.
As the 'nosmt' functionality has become popular due to the speculative
hardware vulnerabilities, the half torn down state is not a proper solution
to the problem.
Enforce CONFIG_HOTPLUG_CPU=y when SMP is enabled so the full operation is
possible.
Reported-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Konrad Wilk <konrad.wilk@oracle.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Mukesh Ojha <mojha@codeaurora.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Rik van Riel <riel@surriel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Micheal Kelley <michael.h.kelley@microsoft.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190326163811.598166056@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Tue, 26 Mar 2019 16:36:05 +0000 (17:36 +0100)]
cpu/hotplug: Prevent crash when CPU bringup fails on CONFIG_HOTPLUG_CPU=n
commit
206b92353c839c0b27a0b9bec24195f93fd6cf7a upstream.
Tianyu reported a crash in a CPU hotplug teardown callback when booting a
kernel which has CONFIG_HOTPLUG_CPU disabled with the 'nosmt' boot
parameter.
It turns out that the SMP=y CONFIG_HOTPLUG_CPU=n case has been broken
forever in case that a bringup callback fails. Unfortunately this issue was
not recognized when the CPU hotplug code was reworked, so the shortcoming
just stayed in place.
When a bringup callback fails, the CPU hotplug code rolls back the
operation and takes the CPU offline.
The 'nosmt' command line argument uses a bringup failure to abort the
bringup of SMT sibling CPUs. This partial bringup is required due to the
MCE misdesign on Intel CPUs.
With CONFIG_HOTPLUG_CPU=y the rollback works perfectly fine, but
CONFIG_HOTPLUG_CPU=n lacks essential mechanisms to exercise the low level
teardown of a CPU including the synchronizations in various facilities like
RCU, NOHZ and others.
As a consequence the teardown callbacks which must be executed on the
outgoing CPU within stop machine with interrupts disabled are executed on
the control CPU in interrupt enabled and preemptible context causing the
kernel to crash and burn. The pre state machine code has a different
failure mode which is more subtle and resulting in a less obvious use after
free crash because the control side frees resources which are still in use
by the undead CPU.
But this is not a x86 only problem. Any architecture which supports the
SMP=y HOTPLUG_CPU=n combination suffers from the same issue. It's just less
likely to be triggered because in 99.99999% of the cases all bringup
callbacks succeed.
The easy solution of making HOTPLUG_CPU mandatory for SMP is not working on
all architectures as the following architectures have either no hotplug
support at all or not all subarchitectures support it:
alpha, arc, hexagon, openrisc, riscv, sparc (32bit), mips (partial).
Crashing the kernel in such a situation is not an acceptable state
either.
Implement a minimal rollback variant by limiting the teardown to the point
where all regular teardown callbacks have been invoked and leave the CPU in
the 'dead' idle state. This has the following consequences:
- the CPU is brought down to the point where the stop_machine takedown
would happen.
- the CPU stays there forever and is idle
- The CPU is cleared in the CPU active mask, but not in the CPU online
mask which is a legit state.
- Interrupts are not forced away from the CPU
- All facilities which only look at online mask would still see it, but
that is the case during normal hotplug/unplug operations as well. It's
just a (way) longer time frame.
This will expose issues, which haven't been exposed before or only seldom,
because now the normally transient state of being non active but online is
a permanent state. In testing this exposed already an issue vs. work queues
where the vmstat code schedules work on the almost dead CPU which ends up
in an unbound workqueue and triggers 'preemtible context' warnings. This is
not a problem of this change, it merily exposes an already existing issue.
Still this is better than crashing fully without a chance to debug it.
This is mainly thought as workaround for those architectures which do not
support HOTPLUG_CPU. All others should enforce HOTPLUG_CPU for SMP.
Fixes:
2e1a3483ce74 ("cpu/hotplug: Split out the state walk into functions")
Reported-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Konrad Wilk <konrad.wilk@oracle.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Mukesh Ojha <mojha@codeaurora.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Rik van Riel <riel@surriel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Micheal Kelley <michael.h.kelley@microsoft.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190326163811.503390616@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Tue, 26 Mar 2019 21:51:02 +0000 (22:51 +0100)]
watchdog: Respect watchdog cpumask on CPU hotplug
commit
7dd47617114921fdd8c095509e5e7b4373cc44a1 upstream.
The rework of the watchdog core to use cpu_stop_work broke the watchdog
cpumask on CPU hotplug.
The watchdog_enable/disable() functions are now called unconditionally from
the hotplug callback, i.e. even on CPUs which are not in the watchdog
cpumask. As a consequence the watchdog can become unstoppable.
Only invoke them when the plugged CPU is in the watchdog cpumask.
Fixes:
9cf57731b63e ("watchdog/softlockup: Replace "watchdog/%u" threads with cpu_stop_work")
Reported-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1903262245490.1789@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Fri, 22 Mar 2019 12:37:24 +0000 (23:37 +1100)]
powerpc/64: Fix memcmp reading past the end of src/dest
commit
d9470757398a700d9450a43508000bcfd010c7a4 upstream.
Chandan reported that fstests' generic/026 test hit a crash:
BUG: Unable to handle kernel data access at 0xc00000062ac40000
Faulting instruction address: 0xc000000000092240
Oops: Kernel access of bad area, sig: 11 [#1]
LE SMP NR_CPUS=2048 DEBUG_PAGEALLOC NUMA pSeries
CPU: 0 PID: 27828 Comm: chacl Not tainted
5.0.0-rc2-next-20190115-00001-g6de6dba64dda #1
NIP:
c000000000092240 LR:
c00000000066a55c CTR:
0000000000000000
REGS:
c00000062c0c3430 TRAP: 0300 Not tainted (
5.0.0-rc2-next-20190115-00001-g6de6dba64dda)
MSR:
8000000002009033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR:
44000842 XER:
20000000
CFAR:
00007fff7f3108ac DAR:
c00000062ac40000 DSISR:
40000000 IRQMASK: 0
GPR00:
0000000000000000 c00000062c0c36c0 c0000000017f4c00 c00000000121a660
GPR04:
c00000062ac3fff9 0000000000000004 0000000000000020 00000000275b19c4
GPR08:
000000000000000c 46494c4500000000 5347495f41434c5f c0000000026073a0
GPR12:
0000000000000000 c0000000027a0000 0000000000000000 0000000000000000
GPR16:
0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20:
c00000062ea70020 c00000062c0c38d0 0000000000000002 0000000000000002
GPR24:
c00000062ac3ffe8 00000000275b19c4 0000000000000001 c00000062ac30000
GPR28:
c00000062c0c38d0 c00000062ac30050 c00000062ac30058 0000000000000000
NIP memcmp+0x120/0x690
LR xfs_attr3_leaf_lookup_int+0x53c/0x5b0
Call Trace:
xfs_attr3_leaf_lookup_int+0x78/0x5b0 (unreliable)
xfs_da3_node_lookup_int+0x32c/0x5a0
xfs_attr_node_addname+0x170/0x6b0
xfs_attr_set+0x2ac/0x340
__xfs_set_acl+0xf0/0x230
xfs_set_acl+0xd0/0x160
set_posix_acl+0xc0/0x130
posix_acl_xattr_set+0x68/0x110
__vfs_setxattr+0xa4/0x110
__vfs_setxattr_noperm+0xac/0x240
vfs_setxattr+0x128/0x130
setxattr+0x248/0x600
path_setxattr+0x108/0x120
sys_setxattr+0x28/0x40
system_call+0x5c/0x70
Instruction dump:
7d201c28 7d402428 7c295040 38630008 38840008 408201f0 4200ffe8 2c050000
4182ff6c 20c50008 54c61838 7d201c28 <
7d402428>
7d293436 7d4a3436 7c295040
The instruction dump decodes as:
subfic r6,r5,8
rlwinm r6,r6,3,0,28
ldbrx r9,0,r3
ldbrx r10,0,r4 <-
Which shows us doing an 8 byte load from
c00000062ac3fff9, which
crosses the page boundary at
c00000062ac40000 and faults.
It's not OK for memcmp to read past the end of the source or
destination buffers if that would cross a page boundary, because we
don't know that the next page is mapped.
As pointed out by Segher, we can read past the end of the source or
destination as long as we don't cross a 4K boundary, because that's
our minimum page size on all platforms.
The bug is in the code at the .Lcmp_rest_lt8bytes label. When we get
there we know that s1 is 8-byte aligned and we have at least 1 byte to
read, so a single 8-byte load won't read past the end of s1 and cross
a page boundary.
But we have to be more careful with s2. So check if it's within 8
bytes of a 4K boundary and if so go to the byte-by-byte loop.
Fixes:
2d9ee327adce ("powerpc/64: Align bytes before fall back to .Lshort in powerpc64 memcmp()")
Cc: stable@vger.kernel.org # v4.19+
Reported-by: Chandan Rajendra <chandan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org>
Tested-by: Chandan Rajendra <chandan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gautham R. Shenoy [Fri, 8 Mar 2019 15:33:24 +0000 (21:03 +0530)]
powerpc/pseries/energy: Use OF accessor functions to read ibm,drc-indexes
commit
ce9afe08e71e3f7d64f337a6e932e50849230fc2 upstream.
In cpu_to_drc_index() in the case when FW_FEATURE_DRC_INFO is absent,
we currently use of_read_property() to obtain the pointer to the array
corresponding to the property "ibm,drc-indexes". The elements of this
array are of type __be32, but are accessed without any conversion to
the OS-endianness, which is buggy on a Little Endian OS.
Fix this by using of_property_read_u32_index() accessor function to
safely read the elements of the array.
Fixes:
e83636ac3334 ("pseries/drc-info: Search DRC properties for CPU indexes")
Cc: stable@vger.kernel.org # v4.16+
Reported-by: Pavithra R. Prakash <pavrampu@in.ibm.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
[mpe: Make the WARN_ON a WARN_ON_ONCE so it's not retriggerable]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rolf Eike Beer [Tue, 26 Mar 2019 17:48:39 +0000 (12:48 -0500)]
objtool: Query pkg-config for libelf location
commit
056d28d135bca0b1d0908990338e00e9dadaf057 upstream.
If it is not in the default location, compilation fails at several points.
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/91a25e992566a7968fedc89ec80e7f4c83ad0548.1553622500.git.jpoimboe@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adrian Hunter [Mon, 25 Mar 2019 13:51:35 +0000 (15:51 +0200)]
perf intel-pt: Fix TSC slip
commit
f3b4e06b3bda759afd042d3d5fa86bea8f1fe278 upstream.
A TSC packet can slip past MTC packets so that the timestamp appears to
go backwards. One estimate is that can be up to about 40 CPU cycles,
which is certainly less than 0x1000 TSC ticks, but accept slippage an
order of magnitude more to be on the safe side.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org
Fixes:
79b58424b821c ("perf tools: Add Intel PT support for decoding MTC packets")
Link: http://lkml.kernel.org/r/20190325135135.18348-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kan Liang [Fri, 15 Mar 2019 18:00:14 +0000 (11:00 -0700)]
perf pmu: Fix parser error for uncore event alias
commit
e94d6b7f615e6dfbaf9fba7db6011db561461d0c upstream.
Perf fails to parse uncore event alias, for example:
# perf stat -e unc_m_clockticks -a --no-merge sleep 1
event syntax error: 'unc_m_clockticks'
\___ parser error
Current code assumes that the event alias is from one specific PMU.
To find the PMU, perf strcmps the PMU name of event alias with the real
PMU name on the system.
However, the uncore event alias may be from multiple PMUs with common
prefix. The PMU name of uncore event alias is the common prefix.
For example, UNC_M_CLOCKTICKS is clock event for iMC, which include 6
PMUs with the same prefix "uncore_imc" on a skylake server.
The real PMU names on the system for iMC are uncore_imc_0 ...
uncore_imc_5.
The strncmp is used to only check the common prefix for uncore event
alias.
With the patch:
# perf stat -e unc_m_clockticks -a --no-merge sleep 1
Performance counter stats for 'system wide':
723,594,722 unc_m_clockticks [uncore_imc_5]
724,001,954 unc_m_clockticks [uncore_imc_3]
724,042,655 unc_m_clockticks [uncore_imc_1]
724,161,001 unc_m_clockticks [uncore_imc_4]
724,293,713 unc_m_clockticks [uncore_imc_2]
724,340,901 unc_m_clockticks [uncore_imc_0]
1.
002090060 seconds time elapsed
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: stable@vger.kernel.org
Fixes:
ea1fa48c055f ("perf stat: Handle different PMU names with common prefix")
Link: http://lkml.kernel.org/r/1552672814-156173-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lars Persson [Fri, 29 Mar 2019 03:44:28 +0000 (20:44 -0700)]
mm/migrate.c: add missing flush_dcache_page for non-mapped page migrate
commit
d2b2c6dd227ba5b8a802858748ec9a780cb75b47 upstream.
Our MIPS 1004Kc SoCs were seeing random userspace crashes with SIGILL
and SIGSEGV that could not be traced back to a userspace code bug. They
had all the magic signs of an I/D cache coherency issue.
Now recently we noticed that the /proc/sys/vm/compact_memory interface
was quite efficient at provoking this class of userspace crashes.
Studying the code in mm/migrate.c there is a distinction made between
migrating a page that is mapped at the instant of migration and one that
is not mapped. Our problem turned out to be the non-mapped pages.
For the non-mapped page the code performs a copy of the page content and
all relevant meta-data of the page without doing the required D-cache
maintenance. This leaves dirty data in the D-cache of the CPU and on
the 1004K cores this data is not visible to the I-cache. A subsequent
page-fault that triggers a mapping of the page will happily serve the
process with potentially stale code.
What about ARM then, this bug should have seen greater exposure? Well
ARM became immune to this flaw back in 2010, see commit
c01778001a4f
("ARM: 6379/1: Assume new page cache pages have dirty D-cache").
My proposed fix moves the D-cache maintenance inside move_to_new_page to
make it common for both cases.
Link: http://lkml.kernel.org/r/20190315083502.11849-1-larper@axis.com
Fixes:
97ee0524614 ("flush cache before installing new page at migraton")
Signed-off-by: Lars Persson <larper@axis.com>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yang Shi [Fri, 29 Mar 2019 03:43:55 +0000 (20:43 -0700)]
mm: mempolicy: make mbind() return -EIO when MPOL_MF_STRICT is specified
commit
a7f40cfe3b7ada57af9b62fd28430eeb4a7cfcb7 upstream.
When MPOL_MF_STRICT was specified and an existing page was already on a
node that does not follow the policy, mbind() should return -EIO. But
commit
6f4576e3687b ("mempolicy: apply page table walker on
queue_pages_range()") broke the rule.
And commit
c8633798497c ("mm: mempolicy: mbind and migrate_pages support
thp migration") didn't return the correct value for THP mbind() too.
If MPOL_MF_STRICT is set, ignore vma_migratable() to make sure it
reaches queue_pages_to_pte_range() or queue_pages_pmd() to check if an
existing page was already on a node that does not follow the policy.
And, non-migratable vma may be used, return -EIO too if MPOL_MF_MOVE or
MPOL_MF_MOVE_ALL was specified.
Tested with https://github.com/metan-ucw/ltp/blob/master/testcases/kernel/syscalls/mbind/mbind02.c
[akpm@linux-foundation.org: tweak code comment]
Link: http://lkml.kernel.org/r/1553020556-38583-1-git-send-email-yang.shi@linux.alibaba.com
Fixes:
6f4576e3687b ("mempolicy: apply page table walker on queue_pages_range()")
Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com>
Signed-off-by: Oscar Salvador <osalvador@suse.de>
Reported-by: Cyril Hrubis <chrubis@suse.cz>
Suggested-by: Kirill A. Shutemov <kirill@shutemov.name>
Acked-by: Rafael Aquini <aquini@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicolas Boichat [Fri, 29 Mar 2019 03:43:46 +0000 (20:43 -0700)]
iommu/io-pgtable-arm-v7s: request DMA32 memory, and improve debugging
commit
0a352554da69b02f75ca3389c885c741f1f63235 upstream.
IOMMUs using ARMv7 short-descriptor format require page tables (level 1
and 2) to be allocated within the first 4GB of RAM, even on 64-bit
systems.
For level 1/2 pages, ensure GFP_DMA32 is used if CONFIG_ZONE_DMA32 is
defined (e.g. on arm64 platforms).
For level 2 pages, allocate a slab cache in SLAB_CACHE_DMA32. Note that
we do not explicitly pass GFP_DMA[32] to kmem_cache_zalloc, as this is
not strictly necessary, and would cause a warning in mm/sl*b.c, as we
did not update GFP_SLAB_BUG_MASK.
Also, print an error when the physical address does not fit in
32-bit, to make debugging easier in the future.
Link: http://lkml.kernel.org/r/20181210011504.122604-3-drinkcat@chromium.org
Fixes:
ad67f5a6545f ("arm64: replace ZONE_DMA with ZONE_DMA32")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: Huaisheng Ye <yehs1@lenovo.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Sasha Levin <Alexander.Levin@microsoft.com>
Cc: Tomasz Figa <tfiga@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yong Wu <yong.wu@mediatek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicolas Boichat [Fri, 29 Mar 2019 03:43:42 +0000 (20:43 -0700)]
mm: add support for kmem caches in DMA32 zone
commit
6d6ea1e967a246f12cfe2f5fb743b70b2e608d4a upstream.
Patch series "iommu/io-pgtable-arm-v7s: Use DMA32 zone for page tables",
v6.
This is a followup to the discussion in [1], [2].
IOMMUs using ARMv7 short-descriptor format require page tables (level 1
and 2) to be allocated within the first 4GB of RAM, even on 64-bit
systems.
For L1 tables that are bigger than a page, we can just use
__get_free_pages with GFP_DMA32 (on arm64 systems only, arm would still
use GFP_DMA).
For L2 tables that only take 1KB, it would be a waste to allocate a full
page, so we considered 3 approaches:
1. This series, adding support for GFP_DMA32 slab caches.
2. genalloc, which requires pre-allocating the maximum number of L2 page
tables (4096, so 4MB of memory).
3. page_frag, which is not very memory-efficient as it is unable to reuse
freed fragments until the whole page is freed. [3]
This series is the most memory-efficient approach.
stable@ note:
We confirmed that this is a regression, and IOMMU errors happen on 4.19
and linux-next/master on MT8173 (elm, Acer Chromebook R13). The issue
most likely starts from commit
ad67f5a6545f ("arm64: replace ZONE_DMA
with ZONE_DMA32"), i.e. 4.15, and presumably breaks a number of Mediatek
platforms (and maybe others?).
[1] https://lists.linuxfoundation.org/pipermail/iommu/2018-November/030876.html
[2] https://lists.linuxfoundation.org/pipermail/iommu/2018-December/031696.html
[3] https://patchwork.codeaurora.org/patch/671639/
This patch (of 3):
IOMMUs using ARMv7 short-descriptor format require page tables to be
allocated within the first 4GB of RAM, even on 64-bit systems. On arm64,
this is done by passing GFP_DMA32 flag to memory allocation functions.
For IOMMU L2 tables that only take 1KB, it would be a waste to allocate
a full page using get_free_pages, so we considered 3 approaches:
1. This patch, adding support for GFP_DMA32 slab caches.
2. genalloc, which requires pre-allocating the maximum number of L2
page tables (4096, so 4MB of memory).
3. page_frag, which is not very memory-efficient as it is unable
to reuse freed fragments until the whole page is freed.
This change makes it possible to create a custom cache in DMA32 zone using
kmem_cache_create, then allocate memory using kmem_cache_alloc.
We do not create a DMA32 kmalloc cache array, as there are currently no
users of kmalloc(..., GFP_DMA32). These calls will continue to trigger a
warning, as we keep GFP_DMA32 in GFP_SLAB_BUG_MASK.
This implies that calls to kmem_cache_*alloc on a SLAB_CACHE_DMA32
kmem_cache must _not_ use GFP_DMA32 (it is anyway redundant and
unnecessary).
Link: http://lkml.kernel.org/r/20181210011504.122604-2-drinkcat@chromium.org
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Sasha Levin <Alexander.Levin@microsoft.com>
Cc: Huaisheng Ye <yehs1@lenovo.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Yong Wu <yong.wu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Tomasz Figa <tfiga@google.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Romain Izard [Fri, 22 Mar 2019 15:53:02 +0000 (16:53 +0100)]
usb: cdc-acm: fix race during wakeup blocking TX traffic
commit
93e1c8a638308980309e009cc40b5a57ef87caf1 upstream.
When the kernel is compiled with preemption enabled, the URB completion
handler can run in parallel with the work responsible for waking up the
tty layer. If the URB handler sets the EVENT_TTY_WAKEUP bit during the
call to tty_port_tty_wakeup() to signal that there is room for additional
input, it will be cleared at the end of this call. As a result, TX traffic
on the upper layer will be blocked.
This can be seen with a kernel configured with CONFIG_PREEMPT, and a fast
modem connected with PPP running over a USB CDC-ACM port.
Use test_and_clear_bit() instead, which ensures that each wakeup requested
by the URB completion code will trigger a call to tty_port_tty_wakeup().
Fixes:
1aba579f3cf5 cdc-acm: handle read pipe errors
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Fri, 22 Mar 2019 15:50:17 +0000 (17:50 +0200)]
xhci: Don't let USB3 ports stuck in polling state prevent suspend
commit
d92f2c59cc2cbca6bfb2cc54882b58ba76b15fd4 upstream.
Commit
2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.
Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.
Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).
Original patch was sent to stable, this one should go there as well
Fixes:
2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Fri, 22 Mar 2019 15:50:16 +0000 (17:50 +0200)]
usb: xhci: dbc: Don't free all memory with spinlock held
commit
8867ea262196a6945c24a0fb739575af646ec0e9 upstream.
The xhci debug capability (DbC) feature did its memory cleanup with
spinlock held. dma_free_coherent() warns if called with interrupts
disabled
move the memory cleanup outside the spinlock
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Fri, 22 Mar 2019 15:50:15 +0000 (17:50 +0200)]
xhci: Fix port resume done detection for SS ports with LPM enabled
commit
6cbcf596934c8e16d6288c7cc62dfb7ad8eadf15 upstream.
A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.
Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.
Add U1 and U2 to the possible link states when checking for finished
port resume.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yasushi Asano [Mon, 18 Feb 2019 10:26:34 +0000 (11:26 +0100)]
usb: host: xhci-rcar: Add XHCI_TRUST_TX_LENGTH quirk
commit
40fc165304f0faaae78b761f8ee30b5d216b1850 upstream.
When plugging BUFFALO LUA4-U3-AGT USB3.0 to Gigabit Ethernet LAN
Adapter, warning messages filled up dmesg.
[ 101.098287] xhci-hcd
ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[ 101.117463] xhci-hcd
ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[ 101.136513] xhci-hcd
ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
Adding the XHCI_TRUST_TX_LENGTH quirk resolves the issue.
Signed-off-by: Yasushi Asano <yasano@jp.adit-jv.com>
Signed-off-by: Spyridon Papageorgiou <spapageorgiou@de.adit-jv.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabrizio Castro [Fri, 1 Mar 2019 11:05:45 +0000 (11:05 +0000)]
usb: common: Consider only available nodes for dr_mode
commit
238e0268c82789e4c107a37045d529a6dbce51a9 upstream.
There are cases where multiple device tree nodes point to the
same phy node by means of the "phys" property, but we should
only consider those nodes that are marked as available rather
than just any node.
Fixes:
98bfb3946695 ("usb: of: add an api to get dr_mode by the phy node")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>