OSDN Git Service
Christoffer Dall [Tue, 24 Nov 2015 09:31:07 +0000 (10:31 +0100)]
KVM: arm/arm64: Fix preemptible timer active state crazyness
We were setting the physical active state on the GIC distributor in a
preemptible section, which could cause us to set the active state on
different physical CPU from the one we were actually going to run on,
hacoc ensues.
Since we are no longer descheduling/scheduling soft timers in the
flush/sync timer functions, simply moving the timer flush into a
non-preemptible section.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Marc Zyngier [Mon, 16 Nov 2015 10:28:18 +0000 (10:28 +0000)]
arm64: KVM: Add workaround for Cortex-A57 erratum 834220
Cortex-A57 parts up to r1p2 can misreport Stage 2 translation faults
when a Stage 1 permission fault or device alignment fault should
have been reported.
This patch implements the workaround (which is to validate that the
Stage-1 translation actually succeeds) by using code patching.
Cc: stable@vger.kernel.org
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Marc Zyngier [Mon, 16 Nov 2015 10:28:17 +0000 (10:28 +0000)]
arm64: KVM: Fix AArch32 to AArch64 register mapping
When running a 32bit guest under a 64bit hypervisor, the ARMv8
architecture defines a mapping of the 32bit registers in the 64bit
space. This includes banked registers that are being demultiplexed
over the 64bit ones.
On exceptions caused by an operation involving a 32bit register, the
HW exposes the register number in the ESR_EL2 register. It was so
far understood that SW had to distinguish between AArch32 and AArch64
accesses (based on the current AArch32 mode and register number).
It turns out that I misinterpreted the ARM ARM, and the clue is in
D1.20.1: "For some exceptions, the exception syndrome given in the
ESR_ELx identifies one or more register numbers from the issued
instruction that generated the exception. Where the exception is
taken from an Exception level using AArch32 these register numbers
give the AArch64 view of the register."
Which means that the HW is already giving us the translated version,
and that we shouldn't try to interpret it at all (for example, doing
an MMIO operation from the IRQ mode using the LR register leads to
very unexpected behaviours).
The fix is thus not to perform a call to vcpu_reg32() at all from
vcpu_reg(), and use whatever register number is supplied directly.
The only case we need to find out about the mapping is when we
actively generate a register access, which only occurs when injecting
a fault in a guest.
Cc: stable@vger.kernel.org
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Ard Biesheuvel [Tue, 10 Nov 2015 14:11:20 +0000 (15:11 +0100)]
ARM/arm64: KVM: test properly for a PTE's uncachedness
The open coded tests for checking whether a PTE maps a page as
uncached use a flawed '(pte_val(xxx) & CONST) != CONST' pattern,
which is not guaranteed to work since the type of a mapping is
not a set of mutually exclusive bits
For HYP mappings, the type is an index into the MAIR table (i.e, the
index itself does not contain any information whatsoever about the
type of the mapping), and for stage-2 mappings it is a bit field where
normal memory and device types are defined as follows:
#define MT_S2_NORMAL 0xf
#define MT_S2_DEVICE_nGnRE 0x1
I.e., masking *and* comparing with the latter matches on the former,
and we have been getting lucky merely because the S2 device mappings
also have the PTE_UXN bit set, or we would misidentify memory mappings
as device mappings.
Since the unmap_range() code path (which contains one instance of the
flawed test) is used both for HYP mappings and stage-2 mappings, and
considering the difference between the two, it is non-trivial to fix
this by rewriting the tests in place, as it would involve passing
down the type of mapping through all the functions.
However, since HYP mappings and stage-2 mappings both deal with host
physical addresses, we can simply check whether the mapping is backed
by memory that is managed by the host kernel, and only perform the
D-cache maintenance if this is the case.
Cc: stable@vger.kernel.org
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Cory Tusar [Thu, 19 Nov 2015 03:54:39 +0000 (22:54 -0500)]
ARM: dts: vfxxx: Fix dspi[01] spi-num-chipselects.
Per the Vybrid Reference Manual (section 3.8.6.1), dspi0 has 6 chip
select signals associated with it, while dspi1 has only 4.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Hui Wang [Tue, 24 Nov 2015 03:08:18 +0000 (11:08 +0800)]
ALSA: hda - Fix headphone noise after Dell XPS 13 resume back from S3
We have a machine Dell XPS 13 with the codec alc256, after resume back
from S3, the headphone has noise when play sound.
Through comparing with the coeff vaule before and after S3, we found
restoring a coeff register will help remove noise.
BugLink: https://bugs.launchpad.net/bugs/1519168
Cc: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ming Lei [Tue, 24 Nov 2015 02:35:31 +0000 (10:35 +0800)]
blk-merge: warn if figured out segment number is bigger than nr_phys_segments
We had seen lots of reports of this kind issue, so add one
warnning in blk-merge, then it can be triggered easily and
avoid to depend on warning/bug from drivers.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Ming Lei [Tue, 24 Nov 2015 02:35:30 +0000 (10:35 +0800)]
blk-merge: fix blk_bio_segment_split
Commit
bdced438acd83a(block: setup bi_phys_segments after
splitting) introduces function of computing bio->bi_phys_segments
during bio splitting.
Unfortunately both bio->bi_seg_front_size and bio->bi_seg_back_size
arn't computed, so too many physical segments may be obtained
for one request since both the two are used to check if one segment
across two bios can be possible.
This patch fixes the issue by computing the two variables in
blk_bio_segment_split().
Fixes:
bdced438acd83a(block: setup bi_phys_segments after splitting)
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Ming Lei [Tue, 24 Nov 2015 02:35:29 +0000 (10:35 +0800)]
block: fix segment split
Inside blk_bio_segment_split(), previous bvec pointer(bvprvp)
always points to the iterator local variable, which is obviously
wrong, so fix it by pointing to the local variable of 'bvprv'.
Fixes:
5014c311baa2b(block: fix bogus compiler warnings in blk-merge.c)
Cc: stable@kernel.org #4.3
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Benjamin Coddington [Fri, 20 Nov 2015 14:55:30 +0000 (09:55 -0500)]
nfs4: limit callback decoding to received bytes
A truncated cb_compound request will cause the client to decode null or
data from a previous callback for nfs4.1 backchannel case, or uninitialized
data for the nfs4.0 case. This is because the path through
svc_process_common() advances the request's iov_base and decrements iov_len
without adjusting the overall xdr_buf's len field. That causes
xdr_init_decode() to set up the xdr_stream with an incorrect length in
nfs4_callback_compound().
Fixing this for the nfs4.1 backchannel case first requires setting the
correct iov_len and page_len based on the length of received data in the
same manner as the nfs4.0 case.
Then the request's xdr_buf length can be adjusted for both cases based upon
the remaining iov_len and page_len.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Benjamin Coddington [Fri, 20 Nov 2015 14:56:20 +0000 (09:56 -0500)]
nfs4: start callback_ident at idr 1
If clp->cl_cb_ident is zero, then nfs_cb_idr_remove_locked() skips removing
it when the nfs_client is freed. A decoding or server bug can then find
and try to put that first nfs_client which would lead to a crash.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Fixes:
d6870312659d ("nfs4client: convert to idr_alloc()")
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Jeff Layton [Thu, 19 Nov 2015 19:30:26 +0000 (14:30 -0500)]
nfs: use sliding delay when LAYOUTGET gets NFS4ERR_DELAY
When LAYOUTGET gets NFS4ERR_DELAY, we currently will wait 15s before
retrying the call. That is a _very_ long time, so add a timeout value to
struct nfs4_layoutget and pass nfs4_async_handle_error a pointer to it.
This allows the RPC engine to use a sliding delay window, instead of a
15s delay.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Kinglong Mee [Wed, 18 Nov 2015 02:39:26 +0000 (10:39 +0800)]
NFS4: Cleanup FATTR4_WORD0_FS_LOCATIONS after decoding success
Commit
1ca843a2d2 "nfs: Fix GETATTR bitmap verification" has check
the bitmap after decoding success, but decode_attr_fs_locations forgets
cleanup the FATTR4_WORD0_FS_LOCATIONS bits.
decode_getfattr_attrs always return -EIO when meeting FS_LOCATIONS now.
ls: cannot access /mnt/referal: Input/output error
ls: cannot access /mnt/replicas: Input/output error
total 32
drwxr-xr-x. 7 root root 8192 Nov 16 20:36 pnfs
??????????? ? ? ? ? ? referal
??????????? ? ? ? ? ? replicas
v2: clear the bit earlier
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Anna Schumaker [Mon, 16 Nov 2015 19:51:07 +0000 (14:51 -0500)]
NFS: Properly set NFS v4.2 NFSDBG_FACILITY
NFS v4.2 operations can work outside of pNFS, so dprintk() output
shouldn't be placed under NFSDBG_PNFS.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Christoph Hellwig [Fri, 13 Nov 2015 08:38:49 +0000 (09:38 +0100)]
nfs: reduce the amount of ifdefs for v4.2 in nfs4file.c
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Christoph Hellwig [Fri, 13 Nov 2015 08:38:48 +0000 (09:38 +0100)]
nfs: use btrfs ioctl defintions for clone
The NFS CLONE_RANGE defintion was wrong and thus never worked. Fix this
by simply using the btrfs ioctl defintion.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Christoph Hellwig [Fri, 13 Nov 2015 08:38:47 +0000 (09:38 +0100)]
nfs: allow intra-file CLONE
Originally CLONE didn't allow for intra-file clones, but we recently
updated the spec to support this feature which is also supported by
local Linux file systems.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Christoph Hellwig [Fri, 13 Nov 2015 08:38:46 +0000 (09:38 +0100)]
nfs: offer native ioctls even if CONFIG_COMPAT is set
Without this for example 64-bit binaries on typical amd64 distributions
would not be able to use ioctls on NFS. For now this only affects clones.
Additionally ->compat_ioctl is defined even for non-compat builds, so
get rid of the pointless ifdef.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Christoph Hellwig [Fri, 13 Nov 2015 08:38:45 +0000 (09:38 +0100)]
nfs: pass on count for CLONE operations
Currently we pass uninitialized stack garbage in the count parameter.
The value is usually large enought to clone whole files and thus let
simple tests pass, but it makes the tests for range clones very unhappy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Jan Kara [Mon, 23 Nov 2015 12:09:51 +0000 (13:09 +0100)]
vfs: Avoid softlockups with sendfile(2)
The following test program from Dmitry can cause softlockups or RCU
stalls as it copies 1GB from tmpfs into eventfd and we don't have any
scheduling point at that path in sendfile(2) implementation:
int r1 = eventfd(0, 0);
int r2 = memfd_create("", 0);
unsigned long n = 1<<30;
fallocate(r2, 0, 0, n);
sendfile(r1, r2, 0, n);
Add cond_resched() into __splice_from_pipe() to fix the problem.
CC: Dmitry Vyukov <dvyukov@google.com>
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Jan Kara [Mon, 23 Nov 2015 12:09:50 +0000 (13:09 +0100)]
vfs: Make sendfile(2) killable even better
Commit
296291cdd162 (mm: make sendfile(2) killable) fixed an issue where
sendfile(2) was doing a lot of tiny writes into a filesystem and thus
was unkillable for a long time. However sendfile(2) can be (mis)used to
issue lots of writes into arbitrary file descriptor such as evenfd or
similar special file descriptors which never hit the standard filesystem
write path and thus are still unkillable. E.g. the following example
from Dmitry burns CPU for ~16s on my test system without possibility to
be killed:
int r1 = eventfd(0, 0);
int r2 = memfd_create("", 0);
unsigned long n = 1<<30;
fallocate(r2, 0, 0, n);
sendfile(r1, r2, 0, n);
There are actually quite a few tests for pending signals in sendfile
code however we data to write is always available none of them seems to
trigger. So fix the problem by adding a test for pending signal into
splice_from_pipe_next() also before the loop waiting for pipe buffers to
be available. This should fix all the lockup issues with sendfile of the
do-ton-of-tiny-writes nature.
CC: stable@vger.kernel.org
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Tue, 24 Nov 2015 02:11:08 +0000 (21:11 -0500)]
fix sysvfs symlinks
The thing got broken back in 2002 - sysvfs does *not* have inline
symlinks; even short ones have bodies stored in the first block
of file. sysv_symlink() handles that correctly; unfortunately,
attempting to look an existing symlink up will end up confusing
them for inline symlinks, and interpret the block number containing
the body as the body itself.
Nobody has noticed until now, which says something about the level
of testing sysvfs gets ;-/
Cc: stable@vger.kernel.org # all of them, not that anyone cared
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tim Harvey [Thu, 19 Nov 2015 14:49:40 +0000 (06:49 -0800)]
imx: thermal: use CPU temperature grade info for thresholds
The IMX6Q/IMX6DL SoC's have a 2-bit temperature grade stored in OTP which
is valid for all IMX6 SoC's (despite the fact that the IMXSDLRM and
IMXSXRM do not document this - this has been proven via tests as well as
verified by Freescale FAE).
Instead of assuming a fixed 85C for passive cooling threshold and 105C for
critical use the thermal grade for these configurations.
We will set the critical to maxT - 5C and passive to maxT - 10C.
Cc: Anson Huang <b20788@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
----
v3:
- rebase against linux-soc-thermal.git
- added ack's from Shawn and Jon
v2:
- remove check for IMX6Q and update comments: The OTP values have been tested
on IMX6SOLO, IMX6DUALLITE, and IMX6SX and Freescale FAE has shared data with
me that the OTP settings are the same and that the reference manuals will
reflect this in their next updates.
- set critical to max - 5C
- set passive to max - 10C
- display max temp in info
- do not allow passive to be set above critical
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Arnd Bergmann [Tue, 17 Nov 2015 16:48:52 +0000 (17:48 +0100)]
thermal: fix thermal_zone_bind_cooling_device prototype
When the prototype for thermal_zone_bind_cooling_device
changed, the static inline wrapper function was left alone,
which in theory can cause build warnings:
I have seen this error in the past:
drivers/thermal/db8500_thermal.c: In function 'db8500_cdev_bind':
drivers/thermal/db8500_thermal.c:78:9: error: too many arguments to function 'thermal_zone_bind_cooling_device'
ret = thermal_zone_bind_cooling_device(thermal, i, cdev,
while this one no longer shows up, there is no doubt that
the prototype is still wrong, so let's just fix it anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes:
6cd9e9f629f1 ("thermal: of: fix cooling device weights in device tree")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Arnd Bergmann [Mon, 16 Nov 2015 21:43:50 +0000 (22:43 +0100)]
Revert "thermal: qcom_spmi: allow compile test"
This just caused build errors:
warning: (QCOM_SPMI_TEMP_ALARM) selects REGMAP_SPMI which has unmet direct dependencies (SPMI)
drivers/built-in.o: In function `regmap_spmi_ext_gather_write':
:(.text+0x609b0): undefined reference to `spmi_ext_register_write'
:(.text+0x609f0): undefined reference to `spmi_ext_register_writel'
While it's generally a good idea to allow compile testing, in this
case, it just doesn't work, so reverting the patch that
introduced the compile-test variant seems the most appropriate
solution.
Note that SPMI also has a 'depends on ARCH_QCOM || COMPILE_TEST'
statement, so we should be able to enable SPMI on all architectures
for compile testing already.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes:
cb7fb4d34202 ("thermal: qcom_spmi: allow compile test")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Punit Agrawal [Wed, 18 Nov 2015 13:52:44 +0000 (13:52 +0000)]
cpufreq: SCPI: Depend on SCPI clk driver
The SCPI clk driver registers the virtual cpufreq device that kicks off
initialisation of the SCPI cpufreq driver. Also, clk_get() will fail for
the cpufreq driver if the SCPI clk driver is missing.
Fix this by making the SCPI cpufreq driver explicitly depend on the SCPI
clk driver.
Fixes:
8def31034d03 (cpufreq: arm_big_little: add SCPI interface driver)
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki [Mon, 23 Nov 2015 22:49:57 +0000 (23:49 +0100)]
Merge back earlier cpufreq fixes for v4.4.
Prarit Bhargava [Fri, 20 Nov 2015 23:47:57 +0000 (18:47 -0500)]
cpufreq: intel_pstate: Fix limits->max_perf rounding error
A rounding error was found in the calculation of limits->max_perf
in intel_pstate_set_policy(), which is used to calculate the max and min
pstate values in intel_pstate_get_min_max(). In that code,
limits->max_perf is truncated to 2 hex digits such that, for example,
0x169 was incorrectly calculated to 0x16 instead of 0x17. This resulted in
the pstate being set one level too low. This patch rounds the value of
limits->max_perf up instead of down so that the correct max pstate can
be reached.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Prarit Bhargava [Fri, 20 Nov 2015 23:47:56 +0000 (18:47 -0500)]
cpufreq: intel_pstate: Fix limits->max_policy_pct rounding error
I have a Intel (6,63) processor with a "marketing" frequency (from
/proc/cpuinfo) of 2100MHz, and a max turbo frequency of 2600MHz. I
can execute
cpupower frequency-set -g powersave --min 1200MHz --max 2100MHz
and the max_freq_pct is set to 80. When adding load to the system I noticed
that the cpu frequency only reached 2000MHZ and not 2100MHz as expected.
This is because limits->max_policy_pct is calculated as 2100 * 100 /2600 = 80.7
and is rounded down to 80 when it should be rounded up to 81. This patch
adds a DIV_ROUND_UP() which will return the correct value.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Sat, 21 Nov 2015 03:36:49 +0000 (09:06 +0530)]
cpufreq: Always remove sysfs cpuX/cpufreq link on ->remove_dev()
Subsys interface's ->remove_dev() is called when the cpufreq driver is
unregistering or the CPU is getting physically removed. We keep removing
the cpuX/cpufreq link for all CPUs except the last one, which is a
mistake as all CPUs contain a link now.
Because of this, one CPU from each policy will still contain a link (to
an already removed policyX directory), after the cpufreq driver is
unregistered.
Fix that by removing the link first and then only see if the policy is
required to be freed. That will make sure that no links are left out.
Fixes:
96bdda61f58b ("cpufreq: create cpu/cpufreq/policyX directories")
Reported-and-tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Ashwin Chaugule [Thu, 19 Nov 2015 15:40:07 +0000 (10:40 -0500)]
cpufreq: CPPC: Initialize and check CPUFreq CPU co-ord type correctly
The CPU policy struct indicates the co-ordination type
for all CPUs of a common freq domain. Initialize it
correctly using the CPU specific data gathered from
CPPC ACPI lib via acpi_get_psd_map().
The PSD object is optional, so the cpu->shared_type
can also be 0. So instead of assuming any value other
than SW_ANY(0xFD) is unsupported, explictly check
if shared_type is SW_ALL and then bail.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Mon, 23 Nov 2015 21:19:27 +0000 (13:19 -0800)]
Merge tag 'linux-kselftest-4.4-rc3' of git://git./linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"This update consists of one minor documentation fix and a fix to an
existing test"
* tag 'linux-kselftest-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/seccomp: Get page size from sysconf
tools:testing/selftests: fix typo in futex/README
Mike Snitzer [Mon, 23 Nov 2015 18:44:38 +0000 (13:44 -0500)]
dm thin: fix regression in advertised discard limits
When establishing a thin device's discard limits we cannot rely on the
underlying thin-pool device's discard capabilities (which are inherited
from the thin-pool's underlying data device) given that DM thin devices
must provide discard support even when the thin-pool's underlying data
device doesn't support discards.
Users were exposed to this thin device discard limits regression if
their thin-pool's underlying data device does _not_ support discards.
This regression caused all upper-layers that called the
blkdev_issue_discard() interface to not be able to issue discards to
thin devices (because discard_granularity was 0). This regression
wasn't caught earlier because the device-mapper-test-suite's extensive
'thin-provisioning' discard tests are only ever performed against
thin-pool's with data devices that support discards.
Fix is to have thin_io_hints() test the pool's 'discard_enabled' feature
rather than inferring whether or not a thin device's discard support
should be enabled by looking at the thin-pool's discard_granularity.
Fixes:
216076705 ("dm thin: disable discard support for thin devices if pool's is disabled")
Reported-by: Mike Gerber <mike@sprachgewalt.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 4.1+
Murali Karicheri [Mon, 23 Nov 2015 18:35:25 +0000 (10:35 -0800)]
ARM: dts: keystone: k2l: fix kernel crash when clk_ignore_unused is not in bootargs
Currently kernel crash randomly when K2L EVM is booted without
clk_ignore_unused in the bootargs. This workaround is not needed
on other K2 devices such as K2HK and K2E and with this fix, we can
remove the workaround altogether. netcp driver on K2L uses linked
ram on OSR (On chip Static RAM) and requires the clock to this peripheral
enabled for proper functioning. This is the reason for the kernel crash.
So add the clock node to fix this issue.
While at it, remove the workaround documentation as well.
With the fix applied, clk_summary dump shows the clock to OSR enabled.
cat /sys/kernel/debug/clk/clk_summary
------cut--------------
tcp3d-1 0 0
399360000 0 0
tcp3d-0 0 0
399360000 0 0
osr 1 1
399360000 0 0
fftc-0 0 0
399360000 0 0
-----cut----------------
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Michal Morawiec [Mon, 23 Nov 2015 18:35:21 +0000 (10:35 -0800)]
soc: ti: knav_qmss_queue: Fix linking RAM setup for queue managers
Configure linking RAM for both queue managers also in case
when only linking RAM 0 is specified in device tree.
Currently hwqueue driver configures linking RAM(s) to be used
cooperatively by the QMs (shared mode). Therefore if both
queue managers are used then both must be configured with
exactly the same linking RAM info (base address and size)
independent of the number of linking RAM(s) specified in the
device tree.
For proper operation only one linking RAM is required and in most
cases this can be internal one as long as it is able to handle
the number of descriptors used in the system.
Current driver code however skips configuration of second
queue manager if second linking RAM is not specified.
If the configuration for the QM2 is missing there will be
a crash when it tries to push/pop descriptors from its queues.
Signed-off-by: Michal Morawiec <michal.1.morawiec.ext@nokia.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Murali Karicheri [Mon, 19 Oct 2015 18:09:34 +0000 (11:09 -0700)]
soc: ti: use request_firmware_direct() as acc firmware is optional
When firmware image for PDSP firmware is absent in the file system
the kernel boot with ramfs/nfs is stuck for 60 seconds being the
the default timeout. request_firmware_direct() is to take care of
such optional firmware loading and hence replace the call in the
driver with this API.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Vineet Gupta [Mon, 23 Nov 2015 14:02:51 +0000 (19:32 +0530)]
ARC: dw2 unwind: Remove falllback linear search thru FDE entries
Fixes STAR
9000953410: "perf callgraph profiling causing RCU stalls"
| perf record -g -c 15000 -e cycles /sbin/hackbench
|
| INFO: rcu_preempt self-detected stall on CPU
| 1: (1 GPs behind) idle=609/
140000000000002/0 softirq=2914/2915 fqs=603
| Task dump for CPU 1:
in-kernel dwarf unwinder has a fast binary lookup and a fallback linear
search (which iterates thru each of ~11K entries) thus takes 2 orders of
magnitude longer (~3 million cycles vs. 2000). Routines written in hand
assembler lack dwarf info (as we don't support assembler CFI pseudo-ops
yet) fail the unwinder binary lookup, hit linear search, failing
nevertheless in the end.
However the linear search is pointless as binary lookup tables are created
from it in first place. It is impossible to have binary lookup fail while
succeed the linear search. It is pure waste of cycles thus removed by
this patch.
This manifested as RCU stalls / NMI watchdog splat when running
hackbench under perf with callgraph profiling. The triggering condition
was perf counter overflowing in routine lacking dwarf info (like memset)
leading to patheic 3 million cycle unwinder slow path and by the time it
returned new interrupts were already pending (Timer, IPI) and taken
rightaway. The original memset didn't make forward progress, system kept
accruing more interrupts and more unwinder delayes in a vicious feedback
loop, ultimately triggering the NMI diagnostic.
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Michael Neuling [Thu, 19 Nov 2015 04:44:45 +0000 (15:44 +1100)]
powerpc/tm: Check for already reclaimed tasks
Currently we can hit a scenario where we'll tm_reclaim() twice. This
results in a TM bad thing exception because the second reclaim occurs
when not in suspend mode.
The scenario in which this can happen is the following. We attempt to
deliver a signal to userspace. To do this we need obtain the stack
pointer to write the signal context. To get this stack pointer we
must tm_reclaim() in case we need to use the checkpointed stack
pointer (see get_tm_stackpointer()). Normally we'd then return
directly to userspace to deliver the signal without going through
__switch_to().
Unfortunatley, if at this point we get an error (such as a bad
userspace stack pointer), we need to exit the process. The exit will
result in a __switch_to(). __switch_to() will attempt to save the
process state which results in another tm_reclaim(). This
tm_reclaim() now causes a TM Bad Thing exception as this state has
already been saved and the processor is no longer in TM suspend mode.
Whee!
This patch checks the state of the MSR to ensure we are TM suspended
before we attempt the tm_reclaim(). If we've already saved the state
away, we should no longer be in TM suspend mode. This has the
additional advantage of checking for a potential TM Bad Thing
exception.
Found using syscall fuzzer.
Fixes:
fb09692e71f1 ("powerpc: Add reclaim and recheckpoint functions for context switching transactional memory processes")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Thu, 19 Nov 2015 04:44:44 +0000 (15:44 +1100)]
powerpc/tm: Block signal return setting invalid MSR state
Currently we allow both the MSR T and S bits to be set by userspace on
a signal return. Unfortunately this is a reserved configuration and
will cause a TM Bad Thing exception if attempted (via rfid).
This patch checks for this case in both the 32 and 64 bit signals
code. If both T and S are set, we mark the context as invalid.
Found using a syscall fuzzer.
Fixes:
2b0a576d15e0 ("powerpc: Add new transactional memory state to the signal context")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicolas Boichat [Wed, 18 Nov 2015 02:45:01 +0000 (10:45 +0800)]
watchdog: mtk_wdt: Use MODE_KEY when stopping the watchdog
WDT_MODE value need to be or-ed with MODE_KEY when setting
watchdog mode. Add it to mtk_wdt_stop function, so that the
watchdog can be stopped (e.g. during suspend).
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Shaohui Xie [Tue, 17 Nov 2015 09:53:19 +0000 (17:53 +0800)]
watchdog: Add support for Freescale Layerscape platforms
Modify watchdog/Kconfig file to support Layerscape platforms.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Andrew Chew [Tue, 10 Nov 2015 00:11:38 +0000 (16:11 -0800)]
watchdog: tegra: Stop watchdog first if restarting
If we need to restart the watchdog due to someone changing the timeout
interval, stop the watchdog before restarting it. Otherwise, the new
timeout doesn't seem to take.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Dan Carpenter [Fri, 6 Nov 2015 09:56:31 +0000 (12:56 +0300)]
watchdog: w83977f_wdt: underflow in wdt_set_timeout()
"t" is controlled by the user. If "t" is a very large integer then it
could lead to a negative "tmrval". We cap the upper bound of "tmrval"
but, in the current code, we allow negatives. This is a bug and it
causes a static checker warning. Let's make "tmrval" unsigned to avoid
this problem.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Vladimir Zapolskiy [Wed, 28 Oct 2015 00:55:35 +0000 (02:55 +0200)]
watchdog: pnx4008: make global wdt_clk static
Silences sparse warning:
drivers/watchdog/pnx4008_wdt.c:83:25:
warning: symbol 'wdt_clk' was not declared. Should it be static?
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Vladimir Zapolskiy [Sat, 17 Oct 2015 18:28:16 +0000 (21:28 +0300)]
watchdog: pnx4008: fix warnings caused by enabling unprepared clock
If common clock framework is configured, the driver generates a warning,
which is fixed by this change:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Tainted: G W 4.3.0-rc2+ #171
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (pnx4008_wdt_probe+0x78/0x11c)
[<>] (pnx4008_wdt_probe) from [<>] (platform_drv_probe+0x50/0xa0)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
[<>] (__platform_driver_register) from [<>] (platform_wdt_driver_init+0x18/0x20)
[<>] (platform_wdt_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Peter Robinson [Mon, 2 Nov 2015 02:20:20 +0000 (02:20 +0000)]
watchdog: omap_wdt: fix null pointer dereference
Fix issue from two patches overlapping causing a kernel oops
[ 3569.297449] Unable to handle kernel NULL pointer dereference at virtual address
00000088
[ 3569.306272] pgd =
dc894000
[ 3569.309287] [
00000088] *pgd=
00000000
[ 3569.313104] Internal error: Oops: 5 [#1] SMP ARM
[ 3569.317986] Modules linked in: ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ebtable_filter ebtable_nat ebtable_broute bridge stp llc ebtables ip6table_security ip6table_raw ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_filter ip6_tables iptable_security iptable_raw iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle musb_dsps cppi41 musb_hdrc phy_am335x udc_core phy_generic phy_am335x_control omap_sham omap_aes omap_rng omap_hwspinlock omap_mailbox hwspinlock_core musb_am335x omap_wdt at24 8250_omap leds_gpio cpufreq_dt smsc davinci_mdio mmc_block ti_cpsw cpsw_common ptp pps_core cpsw_ale davinci_cpdma omap_hsmmc omap_dma mmc_core i2c_dev
[ 3569.386293] CPU: 0 PID: 1429 Comm: wdctl Not tainted 4.3.0-0.rc7.git0.1.fc24.armv7hl #1
[ 3569.394740] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 3569.401179] task:
dbd11a00 ti:
dbaac000 task.ti:
dbaac000
[ 3569.406917] PC is at omap_wdt_get_timeleft+0xc/0x20 [omap_wdt]
[ 3569.413106] LR is at watchdog_ioctl+0x3cc/0x42c
[ 3569.417902] pc : [<
bf0ab138>] lr : [<
c0739c54>] psr:
600f0013
[ 3569.417902] sp :
dbaadf18 ip :
00000003 fp :
7f5d3bbe
[ 3569.430014] r10:
00000000 r9 :
00000003 r8 :
bef21ab8
[ 3569.435535] r7 :
dbbc0f7c r6 :
dbbc0f18 r5 :
bef21ab8 r4 :
00000000
[ 3569.442427] r3 :
00000000 r2 :
00000000 r1 :
8004570a r0 :
dbbc0f18
[ 3569.449323] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 3569.456858] Control:
10c5387d Table:
9c894019 DAC:
00000051
[ 3569.462927] Process wdctl (pid: 1429, stack limit = 0xdbaac220)
[ 3569.469179] Stack: (0xdbaadf18 to 0xdbaae000)
[ 3569.473790] df00:
bef21ab8 dbf60e38
[ 3569.482441] df20:
dc91b840 8004570a bef21ab8 c03988a4 dbaadf48 dc854000 00000000 dd313850
[ 3569.491092] df40:
ddf033b8 0000570a dc91b80b dbaadf3c dbf60e38 00000020 c0df9250 c0df6c48
[ 3569.499741] df60:
dc91b840 8004570a 00000000 dc91b840 dc91b840 8004570a bef21ab8 00000003
[ 3569.508389] df80:
00000000 c03989d4 bef21b74 7f5d3bad 00000003 00000036 c020fcc4 dbaac000
[ 3569.517037] dfa0:
00000000 c020fb00 bef21b74 7f5d3bad 00000003 8004570a bef21ab8 00000001
[ 3569.525685] dfc0:
bef21b74 7f5d3bad 00000003 00000036 00000001 00000000 7f5e4eb0 7f5d3bbe
[ 3569.534334] dfe0:
7f5e4f10 bef21a3c 7f5d0a54 b6e97e0c a00f0010 00000003 00000000 00000000
[ 3569.543038] [<
bf0ab138>] (omap_wdt_get_timeleft [omap_wdt]) from [<
c0739c54>] (watchdog_ioctl+0x3cc/0x42c)
[ 3569.553266] [<
c0739c54>] (watchdog_ioctl) from [<
c03988a4>] (do_vfs_ioctl+0x5bc/0x698)
[ 3569.561648] [<
c03988a4>] (do_vfs_ioctl) from [<
c03989d4>] (SyS_ioctl+0x54/0x7c)
[ 3569.569400] [<
c03989d4>] (SyS_ioctl) from [<
c020fb00>] (ret_fast_syscall+0x0/0x3c)
[ 3569.577413] Code:
e12fff1e e52de004 e8bd4000 e5903060 (
e5933088)
[ 3569.584089] ---[ end trace
cec3039bd3ae610a ]---
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Anson Huang [Tue, 20 Oct 2015 10:44:19 +0000 (18:44 +0800)]
ARM: imx: add platform irq type setting in gpc
GPC irq domain is a child domain of GIC, now all of platform irqs
are inside GPC domain, during the module populate, all devices irq
should have correct type setting in GIC, however, there is no
.irq_set_type callback setting in GPC, so the irq_set_type will be
skipped and cause all irqs' type in /proc/interrupt are "edge" which
mismatch with irq type setting in dtb file. Since GPC has no irq
type setting, so just tell kernel to use irq_chip_set_type_parent.
Signed-off-by: Anson Huang <Anson.Huang@freescale.com>
Cc: <stable@vger.kernel.org> # 4.1+
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Sanchayan Maity [Sun, 18 Oct 2015 05:48:48 +0000 (11:18 +0530)]
ARM: dts: vfxxx: Fix erroneous property in esdhc0 node
Something seems to have gone wrong during the merging of the device
tree changes with the following patch
"ARM: dts: add property for maximum ADC clock frequencies"
The property "fsl,adck-max-frequency" instead of being applied for
the ADC1 node got applied to the esdhc0 node. This patch fixes it.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Fixes:
def0641e2f61 ("ARM: dts: add property for maximum ADC clock frequencies")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Nicolas Pitre [Sun, 22 Nov 2015 01:41:07 +0000 (20:41 -0500)]
ARM: shmobile: r8a7793: proper constness with __initconst
Both the pointer array and the pointed data have to be const when using
__initconst to be correct. This also fixes LTO builds that otherwise
fail with section mismatch errors.
Fixes:
ec60d95b4fac ("ARM: shmobile: Basic r8a7793 SoC support")
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Linus Torvalds [Mon, 23 Nov 2015 00:45:59 +0000 (16:45 -0800)]
Linux 4.4-rc2
Linus Torvalds [Sun, 22 Nov 2015 23:21:40 +0000 (15:21 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge slub bulk allocator updates from Andrew Morton:
"This missed the merge window because I was waiting for some repairs to
come in. Nothing actually uses the bulk allocator yet and the changes
to other code paths are pretty small. And the net guys are waiting
for this so they can start merging the client code"
More comments from Jesper Dangaard Brouer:
"The kmem_cache_alloc_bulk() call, in mm/slub.c, were included in
previous kernel. The present version contains a bug. Vladimir
Davydov noticed it contained a bug, when kernel is compiled with
CONFIG_MEMCG_KMEM (see commit
03ec0ed57ffc: "slub: fix kmem cgroup
bug in kmem_cache_alloc_bulk"). Plus the mem cgroup counterpart in
kmem_cache_free_bulk() were missing (see commit
033745189b1b "slub:
add missing kmem cgroup support to kmem_cache_free_bulk").
I don't consider the fix stable-material because there are no in-tree
users of the API.
But with known bugs (for memcg) I cannot start using the API in the
net-tree"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
slab/slub: adjust kmem_cache_alloc_bulk API
slub: add missing kmem cgroup support to kmem_cache_free_bulk
slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
slub: optimize bulk slowpath free by detached freelist
slub: support for bulk free with SLUB freelists
Linus Torvalds [Sun, 22 Nov 2015 23:10:57 +0000 (15:10 -0800)]
Merge tag 'tty-4.4-rc2' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a few small tty/serial driver fixes for 4.4-rc2 that resolve
some reported problems.
All have been in linux-next, full details are in the shortlog below"
* tag 'tty-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: export fsl8250_handle_irq
serial: 8250_mid: Add missing dependency
tty: audit: Fix audit source
serial: etraxfs-uart: Fix crash
serial: fsl_lpuart: Fix earlycon support
bcm63xx_uart: Use the device name when registering an interrupt
tty: Fix direct use of tty buffer work
tty: Fix tty_send_xchar() lock order inversion
Linus Torvalds [Sun, 22 Nov 2015 21:26:24 +0000 (13:26 -0800)]
Merge tag 'staging-4.4-rc2' of git://git./linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are some staging and iio driver fixes for 4.4-rc2. All of these
are in response to issues that have been reported and have been in
linux-next for a while"
* tag 'staging-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "Staging: wilc1000: coreconfigurator: Drop unneeded wrapper functions"
iio: adc: xilinx: Fix VREFN scale
iio: si7020: Swap data byte order
iio: adc: vf610_adc: Fix division by zero error
iio:ad7793: Fix ad7785 product ID
iio: ad5064: Fix ad5629/ad5669 shift
iio:ad5064: Make sure ad5064_i2c_write() returns 0 on success
iio: lpc32xx_adc: fix warnings caused by enabling unprepared clock
staging: iio: select IRQ_WORK for IIO_DUMMY_EVGEN
vf610_adc: Fix internal temperature calculation
Linus Torvalds [Sun, 22 Nov 2015 21:15:05 +0000 (13:15 -0800)]
Merge tag 'usb-4.4-rc2' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes and new device ids for 4.4-rc2. All
have been in linux-next and the details are in the shortlog"
* tag 'usb-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (28 commits)
usblp: do not set TASK_INTERRUPTIBLE before lock
USB: MAINTAINERS: cxacru
usb: kconfig: fix warning of select USB_OTG
USB: option: add XS Stick W100-2 from 4G Systems
xhci: Fix a race in usb2 LPM resume, blocking U3 for usb2 devices
usb: xhci: fix checking ep busy for CFC
xhci: Workaround to get Intel xHCI reset working more reliably
usb: chipidea: imx: fix a possible NULL dereference
usb: chipidea: usbmisc_imx: fix a possible NULL dereference
usb: chipidea: otg: gadget module load and unload support
usb: chipidea: debug: disable usb irq while role switch
ARM: dts: imx27.dtsi: change the clock information for usb
usb: chipidea: imx: refine clock operations to adapt for all platforms
usb: gadget: atmel_usba_udc: Expose correct device speed
usb: musb: enable usb_dma parameter
usb: phy: phy-mxs-usb: fix a possible NULL dereference
usb: dwc3: gadget: let us set lower max_speed
usb: musb: fix tx fifo flush handling
usb: gadget: f_loopback: fix the warning during the enumeration
usb: dwc2: host: Fix remote wakeup when not in DWC2_L2
...
Linus Torvalds [Sun, 22 Nov 2015 20:59:46 +0000 (12:59 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
- Fix a flood of annoying build warnings
- A number of fixes for Atheros 79xx platforms
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ath79: Add a machine entry for booting OF machines
MIPS: ath79: Fix the size of the MISC INTC registers in ar9132.dtsi
MIPS: ath79: Fix the DDR control initialization on ar71xx and ar934x
MIPS: Fix flood of warnings about comparsion being always true.
Linus Torvalds [Sun, 22 Nov 2015 20:50:58 +0000 (12:50 -0800)]
Merge branch 'parisc-4.4-2' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc update from Helge Deller:
"This patchset adds Huge Page and HUGETLBFS support for parisc"
Honestly, the hugepage support should have gone through in the merge
window, and is not really an rc-time fix. But it only touches
arch/parisc, and I cannot find it in myself to care. If one of the
three parisc users notices a breakage, I will point at Helge and make
rude farting noises.
* 'parisc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Map kernel text and data on huge pages
parisc: Add Huge Page and HUGETLBFS support
parisc: Use long branch to do_syscall_trace_exit
parisc: Increase initial kernel mapping to 32MB on 64bit kernel
parisc: Initialize the fault vector earlier in the boot process.
parisc: Add defines for Huge page support
parisc: Drop unused MADV_xxxK_PAGES flags from asm/mman.h
parisc: Drop definition of start_thread_som for HP-UX SOM binaries
parisc: Fix wrong comment regarding first pmd entry flags
Linus Torvalds [Sun, 22 Nov 2015 20:37:20 +0000 (12:37 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf tool fixes from Thomas Gleixner:
"A couple of fixes for perf tools:
- Build system updates
- Plug a memory leak in an error path of perf probe
- Tear down probes correctly when adding fails
- Fixes to the perf symbol handling
- Fix ordering of event processing in buildid-list
- Fix per DSO filtering in the histogram browser"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Clear probe_trace_event when add_probe_trace_event() fails
perf probe: Fix memory leaking on failure by clearing all probe_trace_events
perf inject: Also re-pipe lost_samples event
perf buildid-list: Requires ordered events
perf symbols: Fix dso lookup by long name and missing buildids
perf symbols: Allow forcing reading of non-root owned files by root
perf hists browser: The dso can be obtained from popup_action->ms.map->dso
perf hists browser: Fix 'd' hotkey action to filter by DSO
perf symbols: Rebuild rbtree when adjusting symbols for kcore
tools: Add a "make all" rule
tools: Actually install tmon in the install rule
Linus Torvalds [Sun, 22 Nov 2015 20:00:12 +0000 (12:00 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"This update contains:
- MPX updates for handling 32bit processes
- A fix for a long standing bug in 32bit signal frame handling
related to FPU/XSAVE state
- Handle get_xsave_addr() correctly in KVM
- Fix SMAP check under paravirtualization
- Add a comment to the static function trace entry to avoid further
confusion about the difference to dynamic tracing"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Fix SMAP check in PVOPS environments
x86/ftrace: Add comment on static function tracing
x86/fpu: Fix get_xsave_addr() behavior under virtualization
x86/fpu: Fix 32-bit signal frame handling
x86/mpx: Fix 32-bit address space calculation
x86/mpx: Do proper get_user() when running 32-bit binaries on 64-bit kernels
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:58 +0000 (15:57 -0800)]
slab/slub: adjust kmem_cache_alloc_bulk API
Adjust kmem_cache_alloc_bulk API before we have any real users.
Adjust API to return type 'int' instead of previously type 'bool'. This
is done to allow future extension of the bulk alloc API.
A future extension could be to allow SLUB to stop at a page boundary, when
specified by a flag, and then return the number of objects.
The advantage of this approach, would make it easier to make bulk alloc
run without local IRQs disabled. With an approach of cmpxchg "stealing"
the entire c->freelist or page->freelist. To avoid overshooting we would
stop processing at a slab-page boundary. Else we always end up returning
some objects at the cost of another cmpxchg.
To keep compatible with future users of this API linking against an older
kernel when using the new flag, we need to return the number of allocated
objects with this API change.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:55 +0000 (15:57 -0800)]
slub: add missing kmem cgroup support to kmem_cache_free_bulk
Initial implementation missed support for kmem cgroup support in
kmem_cache_free_bulk() call, add this.
If CONFIG_MEMCG_KMEM is not enabled, the compiler should be smart enough
to not add any asm code.
Incoming bulk free objects can belong to different kmem cgroups, and
object free call can happen at a later point outside memcg context. Thus,
we need to keep the orig kmem_cache, to correctly verify if a memcg object
match against its "root_cache" (s->memcg_params.root_cache).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:52 +0000 (15:57 -0800)]
slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
The call slab_pre_alloc_hook() interacts with kmemgc and is not allowed to
be called several times inside the bulk alloc for loop, due to the call to
memcg_kmem_get_cache().
This would result in hitting the VM_BUG_ON in __memcg_kmem_get_cache.
As suggested by Vladimir Davydov, change slab_post_alloc_hook() to be able
to handle an array of objects.
A subtle detail is, loop iterator "i" in slab_post_alloc_hook() must have
same type (size_t) as size argument. This helps the compiler to easier
realize that it can remove the loop, when all debug statements inside loop
evaluates to nothing. Note, this is only an issue because the kernel is
compiled with GCC option: -fno-strict-overflow
In slab_alloc_node() the compiler inlines and optimizes the invocation of
slab_post_alloc_hook(s, flags, 1, &object) by removing the loop and access
object directly.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reported-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Suggested-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:49 +0000 (15:57 -0800)]
slub: optimize bulk slowpath free by detached freelist
This change focus on improving the speed of object freeing in the
"slowpath" of kmem_cache_free_bulk.
The calls slab_free (fastpath) and __slab_free (slowpath) have been
extended with support for bulk free, which amortize the overhead of
the (locked) cmpxchg_double.
To use the new bulking feature, we build what I call a detached
freelist. The detached freelist takes advantage of three properties:
1) the free function call owns the object that is about to be freed,
thus writing into this memory is synchronization-free.
2) many freelist's can co-exist side-by-side in the same slab-page
each with a separate head pointer.
3) it is the visibility of the head pointer that needs synchronization.
Given these properties, the brilliant part is that the detached
freelist can be constructed without any need for synchronization. The
freelist is constructed directly in the page objects, without any
synchronization needed. The detached freelist is allocated on the
stack of the function call kmem_cache_free_bulk. Thus, the freelist
head pointer is not visible to other CPUs.
All objects in a SLUB freelist must belong to the same slab-page.
Thus, constructing the detached freelist is about matching objects
that belong to the same slab-page. The bulk free array is scanned is
a progressive manor with a limited look-ahead facility.
Kmem debug support is handled in call of slab_free().
Notice kmem_cache_free_bulk no longer need to disable IRQs. This
only slowed down single free bulk with approx 3 cycles.
Performance data:
Benchmarked[1] obj size 256 bytes on CPU i7-4790K @ 4.00GHz
SLUB fastpath single object quick reuse: 47 cycles(tsc) 11.931 ns
To get stable and comparable numbers, the kernel have been booted with
"slab_merge" (this also improve performance for larger bulk sizes).
Performance data, compared against fallback bulking:
bulk - fallback bulk - improvement with this patch
1 - 62 cycles(tsc) 15.662 ns - 49 cycles(tsc) 12.407 ns- improved 21.0%
2 - 55 cycles(tsc) 13.935 ns - 30 cycles(tsc) 7.506 ns - improved 45.5%
3 - 53 cycles(tsc) 13.341 ns - 23 cycles(tsc) 5.865 ns - improved 56.6%
4 - 52 cycles(tsc) 13.081 ns - 20 cycles(tsc) 5.048 ns - improved 61.5%
8 - 50 cycles(tsc) 12.627 ns - 18 cycles(tsc) 4.659 ns - improved 64.0%
16 - 49 cycles(tsc) 12.412 ns - 17 cycles(tsc) 4.495 ns - improved 65.3%
30 - 49 cycles(tsc) 12.484 ns - 18 cycles(tsc) 4.533 ns - improved 63.3%
32 - 50 cycles(tsc) 12.627 ns - 18 cycles(tsc) 4.707 ns - improved 64.0%
34 - 96 cycles(tsc) 24.243 ns - 23 cycles(tsc) 5.976 ns - improved 76.0%
48 - 83 cycles(tsc) 20.818 ns - 21 cycles(tsc) 5.329 ns - improved 74.7%
64 - 74 cycles(tsc) 18.700 ns - 20 cycles(tsc) 5.127 ns - improved 73.0%
128 - 90 cycles(tsc) 22.734 ns - 27 cycles(tsc) 6.833 ns - improved 70.0%
158 - 99 cycles(tsc) 24.776 ns - 30 cycles(tsc) 7.583 ns - improved 69.7%
250 - 104 cycles(tsc) 26.089 ns - 37 cycles(tsc) 9.280 ns - improved 64.4%
Performance data, compared current in-kernel bulking:
bulk - curr in-kernel - improvement with this patch
1 - 46 cycles(tsc) - 49 cycles(tsc) - improved (cycles:-3) -6.5%
2 - 27 cycles(tsc) - 30 cycles(tsc) - improved (cycles:-3) -11.1%
3 - 21 cycles(tsc) - 23 cycles(tsc) - improved (cycles:-2) -9.5%
4 - 18 cycles(tsc) - 20 cycles(tsc) - improved (cycles:-2) -11.1%
8 - 17 cycles(tsc) - 18 cycles(tsc) - improved (cycles:-1) -5.9%
16 - 18 cycles(tsc) - 17 cycles(tsc) - improved (cycles: 1) 5.6%
30 - 18 cycles(tsc) - 18 cycles(tsc) - improved (cycles: 0) 0.0%
32 - 18 cycles(tsc) - 18 cycles(tsc) - improved (cycles: 0) 0.0%
34 - 78 cycles(tsc) - 23 cycles(tsc) - improved (cycles:55) 70.5%
48 - 60 cycles(tsc) - 21 cycles(tsc) - improved (cycles:39) 65.0%
64 - 49 cycles(tsc) - 20 cycles(tsc) - improved (cycles:29) 59.2%
128 - 69 cycles(tsc) - 27 cycles(tsc) - improved (cycles:42) 60.9%
158 - 79 cycles(tsc) - 30 cycles(tsc) - improved (cycles:49) 62.0%
250 - 86 cycles(tsc) - 37 cycles(tsc) - improved (cycles:49) 57.0%
Performance with normal SLUB merging is significantly slower for
larger bulking. This is believed to (primarily) be an effect of not
having to share the per-CPU data-structures, as tuning per-CPU size
can achieve similar performance.
bulk - slab_nomerge - normal SLUB merge
1 - 49 cycles(tsc) - 49 cycles(tsc) - merge slower with cycles:0
2 - 30 cycles(tsc) - 30 cycles(tsc) - merge slower with cycles:0
3 - 23 cycles(tsc) - 23 cycles(tsc) - merge slower with cycles:0
4 - 20 cycles(tsc) - 20 cycles(tsc) - merge slower with cycles:0
8 - 18 cycles(tsc) - 18 cycles(tsc) - merge slower with cycles:0
16 - 17 cycles(tsc) - 17 cycles(tsc) - merge slower with cycles:0
30 - 18 cycles(tsc) - 23 cycles(tsc) - merge slower with cycles:5
32 - 18 cycles(tsc) - 22 cycles(tsc) - merge slower with cycles:4
34 - 23 cycles(tsc) - 22 cycles(tsc) - merge slower with cycles:-1
48 - 21 cycles(tsc) - 22 cycles(tsc) - merge slower with cycles:1
64 - 20 cycles(tsc) - 48 cycles(tsc) - merge slower with cycles:28
128 - 27 cycles(tsc) - 57 cycles(tsc) - merge slower with cycles:30
158 - 30 cycles(tsc) - 59 cycles(tsc) - merge slower with cycles:29
250 - 37 cycles(tsc) - 56 cycles(tsc) - merge slower with cycles:19
Joint work with Alexander Duyck.
[1] https://github.com/netoptimizer/prototype-kernel/blob/master/kernel/mm/slab_bulk_test01.c
[akpm@linux-foundation.org: BUG_ON -> WARN_ON;return]
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:46 +0000 (15:57 -0800)]
slub: support for bulk free with SLUB freelists
Make it possible to free a freelist with several objects by adjusting API
of slab_free() and __slab_free() to have head, tail and an objects counter
(cnt).
Tail being NULL indicate single object free of head object. This allow
compiler inline constant propagation in slab_free() and
slab_free_freelist_hook() to avoid adding any overhead in case of single
object free.
This allows a freelist with several objects (all within the same
slab-page) to be free'ed using a single locked cmpxchg_double in
__slab_free() and with an unlocked cmpxchg_double in slab_free().
Object debugging on the free path is also extended to handle these
freelists. When CONFIG_SLUB_DEBUG is enabled it will also detect if
objects don't belong to the same slab-page.
These changes are needed for the next patch to bulk free the detached
freelists it introduces and constructs.
Micro benchmarking showed no performance reduction due to this change,
when debugging is turned off (compiled with CONFIG_SLUB_DEBUG).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Helge Deller [Sat, 21 Nov 2015 23:07:44 +0000 (00:07 +0100)]
parisc: Map kernel text and data on huge pages
Adjust the linker script and map_pages() to map kernel text and data on
physical 1MB huge/large pages.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Sat, 21 Nov 2015 23:07:06 +0000 (00:07 +0100)]
parisc: Add Huge Page and HUGETLBFS support
This patch adds huge page support to allow userspace to allocate huge
pages and to use hugetlbfs filesystem on 32- and 64-bit Linux kernels.
A later patch will add kernel support to map kernel text and data on
huge pages.
The only requirement is, that the kernel needs to be compiled for a
PA8X00 CPU (PA2.0 architecture). Older PA1.X CPUs do not support
variable page sizes. 64bit Kernels are compiled for PA2.0 by default.
Technically on parisc multiple physical huge pages may be needed to
emulate standard 2MB huge pages.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 20 Nov 2015 10:22:32 +0000 (11:22 +0100)]
parisc: Use long branch to do_syscall_trace_exit
Use the 22bit instead of the 17bit branch instruction on a 64bit kernel
to reach the do_syscall_trace_exit function from the gateway page.
A huge page enabled kernel may need the additional branch distance bits.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 20 Nov 2015 10:17:27 +0000 (11:17 +0100)]
parisc: Increase initial kernel mapping to 32MB on 64bit kernel
For the 64bit kernel the initially 16 MB kernel memory might become too
small if you build a kernel with many modules built-in and with kernel
text and data areas mapped on huge pages.
This patch increases the initial mapping to 32MB for 64bit kernels and
keeps 16MB for 32bit kernels.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 20 Nov 2015 09:50:01 +0000 (10:50 +0100)]
parisc: Initialize the fault vector earlier in the boot process.
A fault vector on parisc needs to be 2K aligned. Furthermore the
checksum of the fault vector needs to sum up to 0 which is being
calculated and written at runtime.
Up to now we aligned both PA20 and PA11 fault vectors on the same 4K
page in order to easily write the checksum after having mapped the
kernel read-only (by mapping this page only as read-write).
But when we want to map the kernel text and data on huge pages this
makes things harder.
So, simplify it by aligning both fault vectors on 2K boundries and write
the checksum before we map the page read-only.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 20 Nov 2015 14:46:52 +0000 (15:46 +0100)]
parisc: Add defines for Huge page support
Huge pages on parisc will have the same size as one pmd table, which
is on a 64bit kernel 2MB on a kernel with 4K kernel page sizes, and
on a 32bit kernel 4MB when used with 4K kernel pages.
Since parisc does not physically supports 2MB huge page sizes, emulate
it with two consecutive 1MB page sizes instead. Keeping the same huge
page size as one pmd will allow us to add transparent huge page support
later on.
Bit 21 in the pte flags was unused and will now be used to mark a page
as huge page (_PAGE_HPAGE_BIT).
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Sun, 22 Nov 2015 11:14:14 +0000 (12:14 +0100)]
parisc: Drop unused MADV_xxxK_PAGES flags from asm/mman.h
Drop the MADV_xxK_PAGES flags, which were never used and were from a proposed
API which was never integrated into the generic Linux kernel code.
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Geert Uytterhoeven [Mon, 9 Nov 2015 09:53:26 +0000 (10:53 +0100)]
m68k: Wire up mlock2
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Geert Uytterhoeven [Sun, 15 Nov 2015 10:46:55 +0000 (11:46 +0100)]
m68knommu: Add missing initialization of max_pfn and {min,max}_low_pfn
If max_pfn is not initialized, the block layer may use wrong DMA masks.
Replace open-coded shifts by PFN_DOWN(), and drop the "0 on coldfire"
comment, as it is not even true on all Coldfires, let alone all
m68knommu platforms.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Tested-By: Greg Ungerer <gerg@uclinux.org>
Geert Uytterhoeven [Sun, 15 Nov 2015 10:41:14 +0000 (11:41 +0100)]
m68k/mm: sun3 - Add missing initialization of max_pfn and {min,max}_low_pfn
If max_pfn is not initialized, the various /proc/kpage* files are empty,
and selftests/vm/mlock2-tests will fail. max_pfn is also used by the
block layer to calculate DMA masks.
Switch from init_bootmem_node() to init_bootmem(), as there's only one
memory node on Sun-3. This will initialize min_low_pfn and max_low_pfn,
which was also not done before.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Geert Uytterhoeven [Sun, 15 Nov 2015 10:36:29 +0000 (11:36 +0100)]
m68k/mm: m54xx - Add missing initialization of max_pfn
If max_pfn is not initialized, the various /proc/kpage* files are empty,
and selftests/vm/mlock2-tests will fail. max_pfn is also used by the
block layer to calculate DMA masks.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Tested-by: Greg Ungerer <gerg@uclinux.org>
Geert Uytterhoeven [Sun, 15 Nov 2015 10:34:20 +0000 (11:34 +0100)]
m68k/mm: motorola - Add missing initialization of max_pfn
If max_pfn is not initialized, the various /proc/kpage* files are empty,
and selftests/vm/mlock2-tests will fail. max_pfn is also used by the
block layer to calculate DMA masks.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Linus Torvalds [Sat, 21 Nov 2015 18:49:13 +0000 (10:49 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"A bunch of fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
slub: mark the dangling ifdef #else of CONFIG_SLUB_DEBUG
slub: avoid irqoff/on in bulk allocation
slub: create new ___slab_alloc function that can be called with irqs disabled
mm: fix up sparse warning in gfpflags_allow_blocking
ocfs2: fix umask ignored issue
PM/OPP: add entry in MAINTAINERS
kernel/panic.c: turn off locks debug before releasing console lock
kernel/signal.c: unexport sigsuspend()
kasan: fix kmemleak false-positive in kasan_module_alloc()
fat: fix fake_offset handling on error path
mm/hugetlbfs: fix bugs in fallocate hole punch of areas with holes
mm/page-writeback.c: initialize m_dirty to avoid compile warning
various: fix pci_set_dma_mask return value checking
mm: loosen MADV_NOHUGEPAGE to enable Qemu postcopy on s390
mm: vmalloc: don't remove inexistent guard hole in remove_vm_area()
tools/vm/page-types.c: support KPF_IDLE
ncpfs: don't allow negative timeouts
configfs: allow dynamic group creation
MAINTAINERS: add Moritz as reviewer for FPGA Manager Framework
slab.h: sprinkle __assume_aligned attributes
Linus Torvalds [Sat, 21 Nov 2015 18:26:24 +0000 (10:26 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two timer fixlets from Arnd:
- Use proper constant size in the FSL timer driver
- Prevent a build error for legacy platforms"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Disallow drivers for ARCH_USES_GETTIMEOFFSET
clocksource/fsl: Avoid harmless 64-bit warnings
Linus Torvalds [Sat, 21 Nov 2015 18:19:15 +0000 (10:19 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Three fixes for the ARM GIC interrupt controller from Marc addressing
various shortcomings versus boot initialization and suspend/resume"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic: Add save/restore of the active state
irqchip/gic: Clear enable bits before restoring them
irqchip/gic: Make sure all interrupts are deactivated at boot
Linus Torvalds [Sat, 21 Nov 2015 17:52:07 +0000 (09:52 -0800)]
Merge tag 'for-linus-
20151120' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
- MAINTAINERS updates for brcmnand driver
- Fix reboot hangs seen when multiple NAND flash chips are registered
with the same controller
- Fix build issues on jz4740 NAND driver; the error was introduced in
4.3, so I guess nobody really cared, but we might as well fix it
* tag 'for-linus-
20151120' of git://git.infradead.org/linux-mtd:
MAINTAINERS: brcmnand: Add co-maintainer for Broadcom SoCs
MAINTAINERS: brcmnand: Add Broadcom internal mailing-list
mtd: nand: fix shutdown/reboot for multi-chip systems
mtd: jz4740_nand: fix build on jz4740 after removing gpio.h
Jens Axboe [Sat, 21 Nov 2015 03:29:45 +0000 (20:29 -0700)]
blk-mq: fix calling unplug callbacks with preempt disabled
Liu reported that running certain parts of xfstests threw the
following error:
BUG: sleeping function called from invalid context at mm/page_alloc.c:3190
in_atomic(): 1, irqs_disabled(): 0, pid: 6, name: kworker/u16:0
3 locks held by kworker/u16:0/6:
#0: ("writeback"){++++.+}, at: [<
ffffffff8107f083>] process_one_work+0x173/0x730
#1: ((&(&wb->dwork)->work)){+.+.+.}, at: [<
ffffffff8107f083>] process_one_work+0x173/0x730
#2: (&type->s_umount_key#44){+++++.}, at: [<
ffffffff811e6805>] trylock_super+0x25/0x60
CPU: 5 PID: 6 Comm: kworker/u16:0 Tainted: G OE 4.3.0+ #3
Hardware name: Red Hat KVM, BIOS Bochs 01/01/2011
Workqueue: writeback wb_workfn (flush-btrfs-108)
ffffffff81a3abab ffff88042e282ba8 ffffffff8130191b ffffffff81a3abab
0000000000000c76 ffff88042e282ba8 ffff88042e27c180 ffff88042e282bd8
ffffffff8108ed95 ffff880400000004 0000000000000000 0000000000000c76
Call Trace:
[<
ffffffff8130191b>] dump_stack+0x4f/0x74
[<
ffffffff8108ed95>] ___might_sleep+0x185/0x240
[<
ffffffff8108eea2>] __might_sleep+0x52/0x90
[<
ffffffff811817e8>] __alloc_pages_nodemask+0x268/0x410
[<
ffffffff8109a43c>] ? sched_clock_local+0x1c/0x90
[<
ffffffff8109a6d1>] ? local_clock+0x21/0x40
[<
ffffffff810b9eb0>] ? __lock_release+0x420/0x510
[<
ffffffff810b534c>] ? __lock_acquired+0x16c/0x3c0
[<
ffffffff811ca265>] alloc_pages_current+0xc5/0x210
[<
ffffffffa0577105>] ? rbio_is_full+0x55/0x70 [btrfs]
[<
ffffffff810b7ed8>] ? mark_held_locks+0x78/0xa0
[<
ffffffff81666d50>] ? _raw_spin_unlock_irqrestore+0x40/0x60
[<
ffffffffa0578c0a>] full_stripe_write+0x5a/0xc0 [btrfs]
[<
ffffffffa0578ca9>] __raid56_parity_write+0x39/0x60 [btrfs]
[<
ffffffffa0578deb>] run_plug+0x11b/0x140 [btrfs]
[<
ffffffffa0578e33>] btrfs_raid_unplug+0x23/0x70 [btrfs]
[<
ffffffff812d36c2>] blk_flush_plug_list+0x82/0x1f0
[<
ffffffff812e0349>] blk_sq_make_request+0x1f9/0x740
[<
ffffffff812ceba2>] ? generic_make_request_checks+0x222/0x7c0
[<
ffffffff812cf264>] ? blk_queue_enter+0x124/0x310
[<
ffffffff812cf1d2>] ? blk_queue_enter+0x92/0x310
[<
ffffffff812d0ae2>] generic_make_request+0x172/0x2c0
[<
ffffffff812d0ad4>] ? generic_make_request+0x164/0x2c0
[<
ffffffff812d0ca0>] submit_bio+0x70/0x140
[<
ffffffffa0577b29>] ? rbio_add_io_page+0x99/0x150 [btrfs]
[<
ffffffffa0578a89>] finish_rmw+0x4d9/0x600 [btrfs]
[<
ffffffffa0578c4c>] full_stripe_write+0x9c/0xc0 [btrfs]
[<
ffffffffa057ab7f>] raid56_parity_write+0xef/0x160 [btrfs]
[<
ffffffffa052bd83>] btrfs_map_bio+0xe3/0x2d0 [btrfs]
[<
ffffffffa04fbd6d>] btrfs_submit_bio_hook+0x8d/0x1d0 [btrfs]
[<
ffffffffa05173c4>] submit_one_bio+0x74/0xb0 [btrfs]
[<
ffffffffa0517f55>] submit_extent_page+0xe5/0x1c0 [btrfs]
[<
ffffffffa0519b18>] __extent_writepage_io+0x408/0x4c0 [btrfs]
[<
ffffffffa05179c0>] ? alloc_dummy_extent_buffer+0x140/0x140 [btrfs]
[<
ffffffffa051dc88>] __extent_writepage+0x218/0x3a0 [btrfs]
[<
ffffffff810b7ed8>] ? mark_held_locks+0x78/0xa0
[<
ffffffffa051e2c9>] extent_write_cache_pages.clone.0+0x2f9/0x400 [btrfs]
[<
ffffffffa051e422>] extent_writepages+0x52/0x70 [btrfs]
[<
ffffffffa05001f0>] ? btrfs_set_inode_index+0x70/0x70 [btrfs]
[<
ffffffffa04fcc17>] btrfs_writepages+0x27/0x30 [btrfs]
[<
ffffffff81184df3>] do_writepages+0x23/0x40
[<
ffffffff81212229>] __writeback_single_inode+0x89/0x4d0
[<
ffffffff81212a60>] ? writeback_sb_inodes+0x260/0x480
[<
ffffffff81212a60>] ? writeback_sb_inodes+0x260/0x480
[<
ffffffff8121295f>] ? writeback_sb_inodes+0x15f/0x480
[<
ffffffff81212ad2>] writeback_sb_inodes+0x2d2/0x480
[<
ffffffff810b1397>] ? down_read_trylock+0x57/0x60
[<
ffffffff811e6805>] ? trylock_super+0x25/0x60
[<
ffffffff810d629f>] ? rcu_read_lock_sched_held+0x4f/0x90
[<
ffffffff81212d0c>] __writeback_inodes_wb+0x8c/0xc0
[<
ffffffff812130b5>] wb_writeback+0x2b5/0x500
[<
ffffffff810b7ed8>] ? mark_held_locks+0x78/0xa0
[<
ffffffff810660a8>] ? __local_bh_enable_ip+0x68/0xc0
[<
ffffffff81213362>] ? wb_do_writeback+0x62/0x310
[<
ffffffff812133c1>] wb_do_writeback+0xc1/0x310
[<
ffffffff8107c3d9>] ? set_worker_desc+0x79/0x90
[<
ffffffff81213842>] wb_workfn+0x92/0x330
[<
ffffffff8107f133>] process_one_work+0x223/0x730
[<
ffffffff8107f083>] ? process_one_work+0x173/0x730
[<
ffffffff8108035f>] ? worker_thread+0x18f/0x430
[<
ffffffff810802ed>] worker_thread+0x11d/0x430
[<
ffffffff810801d0>] ? maybe_create_worker+0xf0/0xf0
[<
ffffffff810801d0>] ? maybe_create_worker+0xf0/0xf0
[<
ffffffff810858df>] kthread+0xef/0x110
[<
ffffffff8108f74e>] ? schedule_tail+0x1e/0xd0
[<
ffffffff810857f0>] ? __init_kthread_worker+0x70/0x70
[<
ffffffff816673bf>] ret_from_fork+0x3f/0x70
[<
ffffffff810857f0>] ? __init_kthread_worker+0x70/0x70
The issue is that we've got the software context pinned while
calling blk_flush_plug_list(), which flushes callbacks that
are allowed to sleep. btrfs and raid has such callbacks.
Flip the checks around a bit, so we can enable preempt a bit
earlier and flush plugs without having preempt disabled.
This only affects blk-mq driven devices, and only those that
register a single queue.
Reported-by: Liu Bo <bo.li.liu@oracle.com>
Tested-by: Liu Bo <bo.li.liu@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Arnd Bergmann [Mon, 16 Nov 2015 15:48:09 +0000 (16:48 +0100)]
serial: export fsl8250_handle_irq
fsl8250_handle_irq is now used by the of_serial driver, and that fails
if it is a loadable module:
ERROR: "fsl8250_handle_irq" [drivers/tty/serial/of_serial.ko] undefined!
This exports the symbol to avoid randconfig errors.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes:
d43b54d269d2 ("serial: Enable Freescale 16550 workaround on arm")
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Thu, 12 Nov 2015 13:21:23 +0000 (15:21 +0200)]
serial: 8250_mid: Add missing dependency
8250_mid uses rational_best_approximation() function, so the
driver needs to select CONFIG_RATIONAL option.
This fixes build error when CONFIG_RATIONAL is not enabled:
drivers/built-in.o: In function `mid8250_set_termios':
8250_mid.c:(.text+0x10169a): undefined reference to `rational_best_approximation'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 8 Nov 2015 13:52:31 +0000 (08:52 -0500)]
tty: audit: Fix audit source
The data to audit/record is in the 'from' buffer (ie., the input
read buffer).
Fixes:
72586c6061ab ("n_tty: Fix auditing support for cannonical mode")
Cc: stable <stable@vger.kernel.org> # 4.1+
Cc: Miloslav Trmač <mitr@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter Roeck [Mon, 2 Nov 2015 02:32:56 +0000 (18:32 -0800)]
serial: etraxfs-uart: Fix crash
Since commit
7d8c70d8048c ("serial: mctrl-gpio: rename init function"),
crisv32 either do not build or crash as follows.
Unable to handle kernel NULL pointer dereference
Linux 4.3.0-rc7-next-
20151101 #1 Sun Nov 1 11:41:28 PST 2015
...
Call Trace: [<
c0004a0e>] show_stack+0x0/0x9e
[<
c004c0c0>] printk+0x0/0x2c
[<
c00059d4>] show_registers+0x14a/0x1c2
[<
c004c0c0>] printk+0x0/0x2c
[<
c0004b52>] die_if_kernel+0x7c/0x9e
[<
c0005346>] do_page_fault+0x32e/0x3e6
[<
c01dc59c>] of_get_property+0x0/0x2c
[<
c01e0558>] of_irq_parse_raw+0x12a/0x376
[<
c01dc59c>] of_get_property+0x0/0x2c
[<
c0053aca>] get_page_from_freelist+0x73e/0x856
[<
c01dc59c>] of_get_property+0x0/0x2c
[<
c0008912>] d_mmu_refill+0x10a/0x112
[<
c01b488c>] devm_kmalloc+0x40/0x56
[<
c01b47d0>] add_dr+0xc/0x1c
[<
c01b4800>] devm_add_action+0x2/0x4e
[<
c01abdbc>] mctrl_gpio_init_noauto+0x1c/0x76
[<
c01abf9e>] mctrl_gpio_init+0x22/0x110
The function call in the etraxfs-uart driver was not renamed,
possibly due to interference with commit
7b9c5162c182 ("serial:
etraxfs-uart: use mctrl_gpio helpers for handling modem signals").
Fixes:
7d8c70d8048c ("serial: mctrl-gpio: rename init function")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Niklas Cassel <nks@flawful.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Tue, 20 Oct 2015 13:55:21 +0000 (09:55 -0400)]
serial: fsl_lpuart: Fix earlycon support
Earlycon support for Freescale lpuart should only be enabled when
console support is enabled.
Fixes:
1d59b382f1c4 ("serial: fsl_lpuart: add earlycon support")
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simon Arlott [Sun, 15 Nov 2015 16:14:32 +0000 (16:14 +0000)]
bcm63xx_uart: Use the device name when registering an interrupt
Use the device name when registering an interrupt so that multiple
ports don't all have the same interrupt name.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 8 Nov 2015 12:53:06 +0000 (07:53 -0500)]
tty: Fix direct use of tty buffer work
Recent abstraction of tty buffer work introduced api to manage
tty input kworker; use it.
Fixes:
e176058f0de5 ("tty: Abstract tty buffer work")
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Wed, 11 Nov 2015 13:03:54 +0000 (08:03 -0500)]
tty: Fix tty_send_xchar() lock order inversion
The correct lock order is atomic_write_lock => termios_rwsem, as
established by tty_write() => n_tty_write().
Fixes:
c274f6ef1c666 ("tty: Hold termios_rwsem for tcflow(TCIxxx)")
Reported-and-Tested-by: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:41 +0000 (15:57 -0800)]
slub: mark the dangling ifdef #else of CONFIG_SLUB_DEBUG
The #ifdef of CONFIG_SLUB_DEBUG is located very far from the associated
#else. For readability mark it with a comment.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Lameter [Fri, 20 Nov 2015 23:57:38 +0000 (15:57 -0800)]
slub: avoid irqoff/on in bulk allocation
Use the new function that can do allocation while interrupts are disabled.
Avoids irq on/off sequences.
Signed-off-by: Christoph Lameter <cl@linux.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Lameter [Fri, 20 Nov 2015 23:57:35 +0000 (15:57 -0800)]
slub: create new ___slab_alloc function that can be called with irqs disabled
Bulk alloc needs a function like that because it enables interrupts before
calling __slab_alloc which promptly disables them again using the expensive
local_irq_save().
Signed-off-by: Christoph Lameter <cl@linux.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Layton [Fri, 20 Nov 2015 23:57:32 +0000 (15:57 -0800)]
mm: fix up sparse warning in gfpflags_allow_blocking
sparse says:
include/linux/gfp.h:274:26: warning: incorrect type in return expression (different base types)
include/linux/gfp.h:274:26: expected bool
include/linux/gfp.h:274:26: got restricted gfp_t
...add a forced cast to silence the warning.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Junxiao Bi [Fri, 20 Nov 2015 23:57:30 +0000 (15:57 -0800)]
ocfs2: fix umask ignored issue
New created file's mode is not masked with umask, and this makes umask not
work for ocfs2 volume.
Fixes:
702e5bc ("ocfs2: use generic posix ACL infrastructure")
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Gang He <ghe@suse.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Viresh Kumar [Fri, 20 Nov 2015 23:57:27 +0000 (15:57 -0800)]
PM/OPP: add entry in MAINTAINERS
Add entry for operating performance points into MAINTAINERS file. This
will also allow get_maintainers to list OPP stakeholders properly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rafael Wysocki <rjw@rjwysocki.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vitaly Kuznetsov [Fri, 20 Nov 2015 23:57:24 +0000 (15:57 -0800)]
kernel/panic.c: turn off locks debug before releasing console lock
Commit
08d78658f393 ("panic: release stale console lock to always get the
logbuf printed out") introduced an unwanted bad unlock balance report when
panic() is called directly and not from OOPS (e.g. from out_of_memory()).
The difference is that in case of OOPS we disable locks debug in
oops_enter() and on direct panic call nobody does that.
Fixes:
08d78658f393 ("panic: release stale console lock to always get the logbuf printed out")
Reported-by: kernel test robot <ying.huang@linux.intel.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Baoquan He <bhe@redhat.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Xie XiuQi <xiexiuqi@huawei.com>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Petr Mladek <pmladek@suse.cz>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Richard Weinberger [Fri, 20 Nov 2015 23:57:21 +0000 (15:57 -0800)]
kernel/signal.c: unexport sigsuspend()
sigsuspend() is nowhere used except in signal.c itself, so we can mark it
static do not pollute the global namespace.
But this patch is more than a boring cleanup patch, it fixes a real issue
on UserModeLinux. UML has a special console driver to display ttys using
xterm, or other terminal emulators, on the host side. Vegard reported
that sometimes UML is unable to spawn a xterm and he's facing the
following warning:
WARNING: CPU: 0 PID: 908 at include/linux/thread_info.h:128 sigsuspend+0xab/0xc0()
It turned out that this warning makes absolutely no sense as the UML
xterm code calls sigsuspend() on the host side, at least it tries. But
as the kernel itself offers a sigsuspend() symbol the linker choose this
one instead of the glibc wrapper. Interestingly this code used to work
since ever but always blocked signals on the wrong side. Some recent
kernel change made the WARN_ON() trigger and uncovered the bug.
It is a wonderful example of how much works by chance on computers. :-)
Fixes:
68f3f16d9ad0f1 ("new helper: sigsuspend()")
Signed-off-by: Richard Weinberger <richard@nod.at>
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org> [3.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Fri, 20 Nov 2015 23:57:18 +0000 (15:57 -0800)]
kasan: fix kmemleak false-positive in kasan_module_alloc()
Kmemleak reports the following leak:
unreferenced object 0xfffffbfff41ea000 (size 20480):
comm "modprobe", pid 65199, jiffies
4298875551 (age 542.568s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<
ffffffff82354f5e>] kmemleak_alloc+0x4e/0xc0
[<
ffffffff8152e718>] __vmalloc_node_range+0x4b8/0x740
[<
ffffffff81574072>] kasan_module_alloc+0x72/0xc0
[<
ffffffff810efe68>] module_alloc+0x78/0xb0
[<
ffffffff812f6a24>] module_alloc_update_bounds+0x14/0x70
[<
ffffffff812f8184>] layout_and_allocate+0x16f4/0x3c90
[<
ffffffff812faa1f>] load_module+0x2ff/0x6690
[<
ffffffff813010b6>] SyS_finit_module+0x136/0x170
[<
ffffffff8239bbc9>] system_call_fastpath+0x16/0x1b
[<
ffffffffffffffff>] 0xffffffffffffffff
kasan_module_alloc() allocates shadow memory for module and frees it on
module unloading. It doesn't store the pointer to allocated shadow memory
because it could be calculated from the shadowed address, i.e.
kasan_mem_to_shadow(addr).
Since kmemleak cannot find pointer to allocated shadow, it thinks that
memory leaked.
Use kmemleak_ignore() to tell kmemleak that this is not a leak and shadow
memory doesn't contain any pointers.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OGAWA Hirofumi [Fri, 20 Nov 2015 23:57:15 +0000 (15:57 -0800)]
fat: fix fake_offset handling on error path
For the root directory, . and .. are faked (using dir_emit_dots()) and
ctx->pos is reset from 2 to 0.
A corrupted root directory could cause fat_get_entry() to fail, but
->iterate() (fat_readdir()) reports progress to the VFS (with ctx->pos
rewound to 0), so any following calls to ->iterate() continue to return
the same entries again and again.
The result is that userspace will never see the end of the directory,
causing e.g. 'ls' to hang in a getdents() loop.
[hirofumi@mail.parknet.co.jp: cleanup and make sure to correct fake_offset]
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Richard Weinberger <richard.weinberger@gmail.com>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Kravetz [Fri, 20 Nov 2015 23:57:13 +0000 (15:57 -0800)]
mm/hugetlbfs: fix bugs in fallocate hole punch of areas with holes
Hugh Dickins pointed out problems with the new hugetlbfs fallocate hole
punch code. These problems are in the routine remove_inode_hugepages and
mostly occur in the case where there are holes in the range of pages to be
removed. These holes could be the result of a previous hole punch or
simply sparse allocation. The current code could access pages outside the
specified range.
remove_inode_hugepages handles both hole punch and truncate operations.
Page index handling was fixed/cleaned up so that the loop index always
matches the page being processed. The code now only makes a single pass
through the range of pages as it was determined page faults could not race
with truncate. A cond_resched() was added after removing up to
PAGEVEC_SIZE pages.
Some totally unnecessary code in hugetlbfs_fallocate() that remained from
early development was also removed.
Tested with fallocate tests submitted here:
http://librelist.com/browser//libhugetlbfs/2015/6/25/patch-tests-add-tests-for-fallocate-system-call/
And, some ftruncate tests under development
Fixes:
b5cec28d36f5 ("hugetlbfs: truncate_hugepages() takes a range of pages")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: "Hillf Danton" <hillf.zj@alibaba-inc.com>
Cc: <stable@vger.kernel.org> [4.3]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yang Shi [Fri, 20 Nov 2015 23:57:10 +0000 (15:57 -0800)]
mm/page-writeback.c: initialize m_dirty to avoid compile warning
When building kernel with gcc 5.2, the below warning is raised:
mm/page-writeback.c: In function 'balance_dirty_pages.isra.10':
mm/page-writeback.c:1545:17: warning: 'm_dirty' may be used uninitialized in this function [-Wmaybe-uninitialized]
unsigned long m_dirty, m_thresh, m_bg_thresh;
The m_dirty{thresh, bg_thresh} are initialized in the block of "if
(mdtc)", so if mdts is null, they won't be initialized before being used.
Initialize m_dirty to zero, also initialize m_thresh and m_bg_thresh to
keep consistency.
They are used later by if condition: !mdtc || m_dirty <=
dirty_freerun_ceiling(m_thresh, m_bg_thresh)
If mdtc is null, dirty_freerun_ceiling will not be called at all, so the
initialization will not change any behavior other than just ceasing the
compile warning.
(akpm: the patch actually reduces .text size by ~20 bytes on gcc-4.x.y)
[akpm@linux-foundation.org: add comment]
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>