drm/i915/wopcm: Handle pre-programmed WOPCM registers

Starting from DG2, some of the programming previously done by i915 and
the GuC has been moved to the GSC and the relevant registers are no
longer writable by either CPU or GuC. This is also referred to as GuC
deprivilege.
On the i915 side, this affects the WOPCM registers: these are no longer
programmed by the driver and we do instead expect to find them already
set. This can lead to verification failures because in i915 we cheat a bit
with the WOPCM size defines, to keep the code common across platforms, by
sometimes using a smaller WOPCM size that the actual HW support (which isn't
a problem because the extra size is not needed if the FW fits in the smaller
chunk), while the pre-programmed values can use the actual size.
Given tha the new programming entity is trusted, relax the amount of the
checks done on the pre-programmed values by not limiting the max
programmed size. In the extremely unlikely scenario that the registers
have been misprogrammed, we will still fail later at DMA time.

v2: drop special case for DG2 G10 A0 (Alan)

Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Stuart Summers <stuart.summers@intel.com>
Cc: John Harrison <john.c.harrison@intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120212947.3440448-1-daniele.ceraolospurio@intel.com

drm/i915/rpl-s: Add stepping info

Add stepping-substepping info in
accordance to BSpec changes.
Though it looks weird, the revision ID
for the newer stepping is indeed backwards
and is in accordance to the spec.

v2: Rearrange the platforms in logical order (Matt)

Bspec: 53655
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220125223625.4139326-1-anusha.srivatsa@intel.com

drm/i915: Fix vma resource freeing

In some cases we use leftover kfree() instead of i915_vma_resource_free().
Fix this.

Fixes: 2f6b90da9192 ("drm/i915: Use vma resources for async unbinding")
Reported-by: Robert Beckett <bob.beckett@collabora.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119174734.213552-1-thomas.hellstrom@linux.intel.com

drm/i915/guc: Use struct_size() helper in kmalloc()

Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.

Also, address the following sparse warnings:
drivers/gpu/drm/i915/gt/uc/intel_guc_ct.c:792:23: warning: using sizeof on a flexible structure

Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220125180726.GA68646@embeddedor

drm/i915/pmu: Use PM timestamp instead of RING TIMESTAMP for reference

All timestamps returned by GuC for GuC PMU busyness are captured from
GUC PM TIMESTAMP. Since this timestamp does not tick when GuC goes idle,
kmd uses RING_TIMESTAMP to measure busyness of an engine with an active
context. In further stress testing, the MMIO read of the RING_TIMESTAMP
is seen to cause a rare hang. Resolve the issue by using gt specific
timestamp from PM which is in sync with the GuC PM timestamp.

Fixes: 77cdd054dd2c ("drm/i915/pmu: Connect engine busyness stats from GuC to pmu")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220111015523.225562-1-umesh.nerlige.ramappa@intel.com

drm/i915/selftests: Use less in contexts steal guc id test

Using more guc_ids in the stealing guc id test has no real benefit.
Tearing down lots of contexts all at the same time takes a bit of time
due to the H2G / G2H ping-pong with the GuC. On some slower platforms
this can cause timeous when flushing the test as the GT isn't idle when
this ping-pong is happening. Reduce the number of guc ids to speed up
the flushing of the test.

Link: https://gitlab.freedesktop.org/drm/intel/-/issues/4821
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220122000822.25616-1-matthew.brost@intel.com

drm/i915/guc: Ensure multi-lrc fini breadcrumb math is correct

Realized that the GuC multi-lrc fini breadcrumb emit code is very
delicate as the math this code does relies on functions it calls to emit
a certain number of DWs. Add a few GEM_BUG_ONs to assert the math is
correct.

v2:
  - Rebase + resend for CI
 (Checkpatch)
  - Fix blank line warning

Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119210639.33053-1-matthew.brost@intel.com

drm/i915/dg2: Add Wa_18018781329

A few more MOD registers need to be programmed on DG2.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120234147.1200574-1-matthew.d.roper@intel.com
Reviewed-by: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>

drm/i915: fix header file inclusion for might_alloc()

Replace "linux/slab.h" with "linux/sched/mm.h" header inclusion
as the first is not required, while the second, if not included,
prodouces the following error:

drivers/gpu/drm/i915/i915_vma_resource.c: In function ‘i915_vma_resource_bind_dep_await’:
drivers/gpu/drm/i915/i915_vma_resource.c:381:9: error: implicit declaration of function ‘might_alloc’; did you mean ‘might_lock’? [-Werror=implicit-function-declaration]
  381 |         might_alloc(gfp);
      |         ^~~~~~~~~~~
      |         might_lock

Fixes: 2f6b90da9192 ("drm/i915: Use vma resources for async unbinding")
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124094418.2661-1-andi.shyti@linux.intel.com

drm/i915: Lock timeline mutex directly in error path of eb_pin_timeline

Don't use the interruptable version of the timeline mutex lock in the
error path of eb_pin_timeline as the cleanup must always happen.

v2:
 (John Harrison)
  - Don't check for interrupt during mutex lock
v3:
 (Tvrtko)
  - A comment explaining why lock helper isn't used

Fixes: 544460c33821 ("drm/i915: Multi-BB execbuf")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220111163929.14017-1-matthew.brost@intel.com

drm/i915/guc: Flush G2H handler during a GT reset

Now that the error capture is fully decoupled from fence signalling
(request retirement to free memory, which in turn depends on resets) we
can safely flush the G2H handler during a GT reset. This eliminates
corner cases where GuC generated G2H (e.g. engine resets) race with a GT
reset.

v2:
 (John Harrison)
  - Fix typo in commit message (s/is/in)

Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220121043118.24886-4-matthew.brost@intel.com

drm/i915/guc: Add work queue to trigger a GT reset

The G2H handler needs to be flushed during a GT reset but a G2H
indicating engine reset failure can trigger a GT reset. Add a worker to
trigger the GT rest when an engine reset failure is received to break
this circular dependency.

v2:
 (John Harrison)
  - Store engine reset mask
  - Fix typo in commit message
v3:
 (John Harrison)
  - Fix another typo in commit message
  - s/reset_*/reset_fail_*/

Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220121043118.24886-3-matthew.brost@intel.com

drm/i915: Allocate intel_engine_coredump_alloc with ALLOW_FAIL

Allocate intel_engine_coredump_alloc with ALLOW_FAIL rather than
GFP_KERNEL to fully decouple the error capture from fence signalling.

v2:
 (John Harrison)
  - Fix typo in commit message (s/do/to)

Fixes: 8b91cdd4f8649 ("drm/i915: Use __GFP_KSWAPD_RECLAIM in the capture code")

Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220121043118.24886-2-matthew.brost@intel.com

drm/i915/guc: Remove hacks for reset and schedule disable G2H being received out of order

In the i915 there are several hacks in place to make request cancellation
work with an old version of the GuC which delivered the G2H indicating
schedule disable is done before G2H indicating a context reset. Version
69 fixes this, so we can remove these hacks.

v2:
 (Checkpatch)
  - s/cancelation/cancellation

Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220113181351.21296-3-matthew.brost@intel.com

drm/i915/selftests: Add a cancel request selftest that triggers a reset

Add a cancel request selftest that results in an engine reset to cancel
the request as it is non-preemptable. Also insert a NOP request after
the cancelled request and confirm that it completes successfully.

v2:
 (Tvrtko)
  - Skip test if preemption timeout compiled out
  - Skip test if engine reset isn't supported
  - Update debug prints to be more descriptive
v3:
  - Add comment explaining test
v4:
 (John Harrison)
  - Fix typos in comment explaining test
  - goto out_rq is NOP creation fails

Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220113181351.21296-2-matthew.brost@intel.com

drm/i915: Remove short-term pins from execbuf, v6.

Add a flag PIN_VALIDATE, to indicate we don't need to pin and only
protected by the object lock.

This removes the need to unpin, which is done by just releasing the
lock.

eb_reserve is slightly reworked for readability, but the same steps
are still done:
- First pass pins with NONBLOCK.
- Second pass unbinds all objects first, then pins.
- Third pass is only called when not all objects are softpinned, and
  unbinds all objects, then calls i915_gem_evict_vm(), then pins.

Changes since v1:
- Split out eb_reserve() into separate functions for readability.
Changes since v2:
- Make batch buffer mappable on platforms where only GGTT is available,
  to prevent moving the batch buffer during relocations.
Changes since v3:
- Preserve current behavior for batch buffer, instead be cautious when
  calling i915_gem_object_ggtt_pin_ww, and re-use the current batch vma
  if it's inside ggtt and map-and-fenceable.
- Remove impossible condition check from eb_reserve. (Matt)
Changes since v5:
- Do not even temporarily pin, just call i915_gem_evict_vm() and mark
  all vma's as unpinned.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220114132320.109030-7-maarten.lankhorst@linux.intel.com

drm/i915: Remove support for unlocked i915_vma unbind

Now that we require the object lock for all ops, some code handling
race conditions can be removed.

This is required to not take short-term pins inside execbuf.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220114132320.109030-6-maarten.lankhorst@linux.intel.com

drm/i915: Add i915_vma_unbind_unlocked, and take obj lock for i915_vma_unbind, v2.

We want to remove more members of i915_vma, which requires the locking to
be held more often.

Start requiring gem object lock for i915_vma_unbind, as it's one of the
callers that may unpin pages.

Some special care is needed when evicting, because the last reference to
the object may be held by the VMA, so after __i915_vma_unbind, vma may be
garbage, and we need to cache vma->obj before unlocking.

Changes since v1:
- Make trylock failing a WARN. (Matt)
- Remove double i915_vma_wait_for_bind() (Matt)
- Move atomic_set to right before mutex_unlock(), to make it more clear
  they belong together. (Matt)

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220114132320.109030-5-maarten.lankhorst@linux.intel.com

drm/i915: Add object locking to i915_gem_evict_for_node and i915_gem_evict_something, v2.

Because we will start to require the obj->resv lock for unbinding,
ensure these vma eviction utility functions also take the lock.

This requires some function signature changes, to ensure that the
ww context is passed around, but is mostly straightforward.

Previously this was split up into several patches, but reworking
should allow for easier bisection.

Changes since v1:
- Handle evicting dead objects better.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220114132320.109030-4-maarten.lankhorst@linux.intel.com

drm/i915: Add locking to i915_gem_evict_vm(), v3.

i915_gem_evict_vm will need to be able to evict objects that are
locked by the current ctx. By testing if the current context already
locked the object, we can do this correctly. This allows us to
evict the entire vm even if we already hold some objects' locks.

Previously, this was spread over several commits, but it makes
more sense to commit the changes to i915_gem_evict_vm separately
from the changes to i915_gem_evict_something() and
i915_gem_evict_for_node().

Changes since v1:
- Handle evicting dead objects better.
Changes since v2:
- Use for_i915_gem_ww in igt_evict_vm. (Thomas)

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
[mlankhorst: Fix up doc warning.]
Link: https://patchwork.freedesktop.org/patch/msgid/20220117075604.131477-1-maarten.lankhorst@linux.intel.com

drm/i915: Call i915_gem_evict_vm in vm_fault_gtt to prevent new ENOSPC errors, v2.

Now that we cannot unbind kill the currently locked object directly
because we're removing short term pinning, we may have to unbind the
object from gtt manually, using a i915_gem_evict_vm() call.

Changes since v1:
- Remove -ENOSPC warning, can still happen with concurrent mmaps
  where we can't unbind the other mmap because of the lock held.
  This  fixes the gem_mmap_gtt@cpuset tests.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220114132320.109030-2-maarten.lankhorst@linux.intel.com

Merge drm/drm-next into drm-intel-gt-next

Maarten needs backmerge to account for header file renames/changes which
landed via drm-intel-next and are interfering with his pinning work.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

i915: make array flex_regs static const

Don't populate the read-only array flex_regs on the stack but
instead it static const. Also makes the object code a little smaller.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220112223435.949071-1-colin.i.king@gmail.com

Merge tag 'amd-drm-next-5.17-2022-01-12' of https://gitlab.freedesktop.org/agd5f/linux into drm-next

amd-drm-next-5.17-2022-01-12:

amdgpu:
- SR-IOV fixes
- Suspend/resume fixes
- Display fixes
- DMCUB fixes
- DP alt mode fixes
- RAS fixes
- UBSAN fix
- Navy Flounder VCN fix
- ttm resource manager cleanup
- default_groups change for kobj_type
- vkms fix
- Aldebaran fixes

amdkfd:
- SDMA ECC interrupt fix
- License clarification
- Pointer check fix
- DQM fixes for hawaii
- default_groups change for kobj_type
- Typo fixes

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220113030537.5758-1-alexander.deucher@amd.com

Merge tag 'drm-misc-next-fixes-2022-01-14' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

 * atomic helpers: Fix error messages
 * mipi-dbi: Fix buffer mapping

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/YeGHu7qU92pjuQOn@linux-uq9g

Merge tag 'drm-misc-fixes-2022-01-14' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

Two DT bindings fixes for meson, a device refcounting fix for sun4i, a
probe fix for vga16fb, a locking fix for the CMA dma-buf heap and a
compilation fix for ttm.

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: I made sure I have exactly the same conflict resolution as
Linus in 8d0749b4f83b ("Merge tag 'drm-next-2022-01-07' of
git://anongit.freedesktop.org/drm/drm") to avoid further conflict fun.
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220114125454.zs46ny52lrxk3ljz@houat

drm/mipi-dbi: Fix source-buffer address in mipi_dbi_buf_copy

Set the source-buffer address after mapping the buffer into the
kernel's address space. Makes MIPI DBI helpers work again.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: c47160d8edcd ("drm/mipi-dbi: Remove dependency on GEM CMA helper library")
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reported-by: Noralf Trønnes <noralf@tronnes.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220111132634.18302-1-tzimmermann@suse.de
(cherry picked from commit 9d31993451f6bb4059a9b9eec4856b2225e36df0)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

drm: fix error found in some cases after the patch d1af5cd86997

The patch d1af5cd86997 ("drm: get rid of DRM_DEBUG_* log
calls in drm core, files drm_a*.c") fails when the drm_device
cannot be found in the parameter plane_state->crtc.
Fix it using plane_state->plane.

Reported-by: kernel test robot <oliver.sang@intel.com>
Fixes: 6e22dc358377 ("drm: get rid of DRM_DEBUG_* log calls in drm core, files drm_a*.c")
Signed-off-by: Claudio Suarez <cssk@net-c.es>
[danvet: fix Fixes: line]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/YaiXEARd8z2C463h@gineta.localdomain
(cherry picked from commit 521d459b1935628a7caa0753429f880dae2dbfc9)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge tag 'drm-misc-next-fixes-2022-01-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

 * Fix use of CRTC state's active vs enable in atomic helper

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/Yd/i/zj9vEHisSSB@linux-uq9g

Merge tag 'drm-intel-next-fixes-2022-01-13' of git://anongit.freedesktop.org/drm/drm-intel into drm-next

- Hold runtime PM wakelock during PXP unbind (Juston Li)
- Three fixes for the TTM backend fault handling (Matthew Auld)
- Make sure to unmap when purging in the TTM backend (Matthew Auld)

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Yd/xzyCM87rfrwQT@tursulin-mobl2

drm/ttm: fix compilation on ARCH=um

Even if it's probably not really useful, it can get selected
by e.g. randconfig builds, and then failing to compile is an
annoyance. Unfortunately, it's hard to fix in Kconfig, since
DRM_TTM is selected by many things that don't really depend
on any specific architecture, and just depend on PCI (which
is indeed now available in ARCH=um via simulation/emulation).

Fix this in the code instead by just ifdef'ing the relevant
two lines that depend on "real X86".

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20211220111519.a4c8c6eff702.Ie4cf4e68698f6a9f546b83379bc52c266504424f@changeid

dma-buf: cma_heap: Fix mutex locking section

Fix cma_heap_buffer mutex locking critical section to protect vmap_cnt
and vaddr.

Fixes: a5d2d29e24be ("dma-buf: heaps: Move heap-helper logic into the cma_heap implementation")
Signed-off-by: Weizhao Ouyang <o451686892@gmail.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220104073545.124244-1-o451686892@gmail.com

video: vga16fb: Only probe for EGA and VGA 16 color graphic cards

The vga16fb framebuffer driver only supports Enhanced Graphics Adapter
(EGA) and Video Graphics Array (VGA) 16 color graphic cards.

But it doesn't check if the adapter is one of those or if a VGA16 mode
is used. This means that the driver will be probed even if a VESA BIOS
Extensions (VBE) or Graphics Output Protocol (GOP) interface is used.

This issue has been present for a long time but it was only exposed by
commit d391c5827107 ("drivers/firmware: move x86 Generic System
Framebuffers support") since the platform device registration to match
the {vesa,efi}fb drivers is done later as a consequence of that change.

All non-x86 architectures though treat orig_video_isVGA as a boolean so
only do the supported video mode check for x86 and not for other arches.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=215001
Fixes: d391c5827107 ("drivers/firmware: move x86 Generic System Framebuffers support")
Reported-by: Kris Karas <bugs-a21@moonlit-rail.com>
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Kris Karas <bugs-a21@moonlit-rail.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220110095625.278836-3-javierm@redhat.com

drm/amdkfd: Fix ASIC name typos

Three misspelled ASICs in comments here, so fix the spelling

Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Fix DQM asserts on Hawaii

start_nocpsch would never set dqm->sched_running on Hawaii due to an
early return statement. This would trigger asserts in other functions
and end up in inconsistent states.

Bug: https://github.com/RadeonOpenCompute/ROCm/issues/1624
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Kent Russell <kent.russell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Use correct VIEWPORT_DIMENSION for DCN2

For some reason this file isn't using the appropriate register
headers for DCN headers, which means that on DCN2 we're getting
the VIEWPORT_DIMENSION offset wrong.

This means that we're not correctly carving out the framebuffer
memory correctly for a framebuffer allocated by EFI and
therefore see corruption when loading amdgpu before the display
driver takes over control of the framebuffer scanout.

Fix this by checking the DCE_HWIP and picking the correct offset
accordingly.

Long-term we should expose this info from DC as GMC shouldn't
need to know about DCN registers.

Cc: stable@vger.kernel.org
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/pm: only send GmiPwrDnControl msg on master die (v3)

PMFW only returns 0 on master die and sends NACK back on other dies for
the message.

v2: only send GmiPwrDnControl msg on master die instead of all
dies.
v3: remove the pointer check for get_socket_id and get_die_id as they
should be present on Aldebaran.

Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: use spin_lock_irqsave to avoid deadlock by local interrupt

This is observed in SRIOV case with virtual KMS as display.

_raw_spin_lock_irqsave+0x37/0x40
drm_handle_vblank+0x69/0x350 [drm]
? try_to_wake_up+0x432/0x5c0
? amdgpu_vkms_prepare_fb+0x1c0/0x1c0 [amdgpu]
drm_crtc_handle_vblank+0x17/0x20 [drm]
amdgpu_vkms_vblank_simulate+0x4d/0x80 [amdgpu]
__hrtimer_run_queues+0xfb/0x230
hrtimer_interrupt+0x109/0x220
__sysvec_apic_timer_interrupt+0x64/0xe0
asm_call_irq_on_stack+0x12/0x20

Fixes: 84ec374bd580 ("drm/amdgpu: create amdgpu_vkms (v4)")
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Kelly Zytaruk <kelly.zytaruk@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: not return error on the init_apu_flags

In some APU project we needn't always assign flags to identify each other,
so we may not need return an error.

Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Use prange->update_list head for remove_list

The remove_list head was only used for keeping track of existing ranges
that are to be removed from the svms->list. The update_list was used for
new or existing ranges that need updated attributes. These two cases are
mutually exclusive (i.e. the same range will never be on both lists).
Therefore we can use the update_list head to track the remove_list and
save another 16 bytes in the svm_range struct.

Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Use prange->list head for insert_list

There are seven list_heads in struct svm_range: list, update_list,
remove_list, insert_list, svm_bo_list, deferred_list, child_list. This
patch and the next one remove two of them that are redundant.

The insert_list head was only used for new ranges that are not on the
svms->list yet. So we can use that list head for keeping track of
new ranges before they get added, and use list_move_tail to move them
to the svms->list when ready.

Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: make SPDX License expression more sound

Commit b5f57384805a ("drm/amdkfd: Add sysfs bitfields and enums to uAPI")
adds include/uapi/linux/kfd_sysfs.h with the "GPL-2.0 OR MIT WITH
Linux-syscall-note" SPDX-License expression.

The command ./scripts/spdxcheck.py warns:

  include/uapi/linux/kfd_sysfs.h: 1:48 Exception not valid for license MIT: Linux-syscall-note

For a uapi header, the file under GPLv2 License must be combined with the
Linux-syscall-note, but combining the MIT License with the
Linux-syscall-note makes no sense, as the note provides an exception for
GPL-licensed code, not for permissively licensed code.

So, reorganize the SPDX expression to only combine the note with the GPL
License condition. This makes spdxcheck happy again.

Fixes: b5f57384805a ("drm/amdkfd: Add sysfs bitfields and enums to uAPI")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: kstewart@linuxfoundation.org
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Check for null pointer after calling kmemdup

As the possible failure of the allocation, kmemdup() may return NULL
pointer.
Therefore, it should be better to check the 'props2' in order to prevent
the dereference of NULL pointer.

Fixes: 3a87177eb141 ("drm/amdkfd: Add topology support for dGPUs")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: invalid parameter check in dmub_hpd_callback

The function performs a check on the "adev" input parameter, however, it
is used before the check.

Initialize the "dev" variable after the sanity check to avoid a possible
NULL pointer dereference.

Fixes: e27c41d5b0681 ("drm/amd/display: Support for DMUB HPD interrupt handling")
Addresses-Coverity-ID: 1493909 ("Null pointer dereference")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Revert "drm/amdgpu: Don't inherit GEM object VMAs in child process"

This reverts commit fbcdbfde87509d523132b59f661a355c731139d0.

Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: reset dcn31 SMU mailbox on failures

Otherwise future commands may fail as well leading to downstream
problems that look like they stemmed from a timeout the first time
but really didn't.

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: use default_groups in kobj_type

There are currently 2 ways to create a set of sysfs files for a
kobj_type, through the default_attrs field, and the default_groups
field.  Move the amdkfd sysfs code to use default_groups field which has
been the preferred way since aa30f47cf666 ("kobject: Add support for
default attribute groups to kobj_type") so that we can soon get rid of
the obsolete default_attrs field.

Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: use default_groups in kobj_type

There are currently 2 ways to create a set of sysfs files for a
kobj_type, through the default_attrs field, and the default_groups
field.  Move the amdgpu sysfs code to use default_groups field which has
been the preferred way since aa30f47cf666 ("kobject: Add support for
default attribute groups to kobj_type") so that we can soon get rid of
the obsolete default_attrs field.

Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Cc: John Clements <john.clements@amd.com>
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Jonathan Kim <jonathan.kim@amd.com>
Cc: Kevin Wang <kevin1.wang@amd.com>
Cc: shaoyunl <shaoyun.liu@amd.com>
Cc: Tao Zhou <tao.zhou1@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/amdgpu: Add pcie indirect support to amdgpu_mm_wreg_mmio_rlc()

The function amdgpu_mm_wreg_mmio_rlc() is used by debugfs to write to
MMIO registers.  It didn't support registers beyond the BAR mapped MMIO
space.  This adds pcie indirect write support.

Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: recover gart table at resume

Get rid off pin/unpin of gart BO at resume/suspend and
instead pin only once and try to recover gart content
at resume time. This is much more stable in case there
is OOM situation at 2nd call to amdgpu_device_evict_resources()
while evicting GART table.

v3: remove gart recovery from other places
v2: pin gart at amdgpu_gart_table_vram_alloc()

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: do not pass ttm_resource_manager to vram_mgr

Do not allow exported amdgpu_vram_mgr_*() to accept
any ttm_resource_manager pointer. Also there is no need
to force other module to call a ttm function just to
eventually call vram_mgr functions.

v2: pass adev's vram_mgr instead of adev

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: remove unused function

Remove unused amdgpu_amdkfd_get_vram_usage()

CC: Felix.Kuehling@amd.com
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes: dfcbe6d5f4a340 ("drm/amdgpu: Remove unused function pointers")

drm/amdgpu: do not pass ttm_resource_manager to gtt_mgr

Do not allow exported amdgpu_gtt_mgr_*() to accept
any ttm_resource_manager pointer. Also there is no need
to force other module to call a ttm function just to
eventually call gtt_mgr functions.

v4: remove unused adev.
v3: upcast mgr from ttm resopurce manager instead of
getting it from adev.
v2: pass adev's gtt_mgr instead of adev.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Unmap MMIO mappings when device is not unplugged

Patch: 3efb17ae7e92 ("drm/amdgpu: Call amdgpu_device_unmap_mmio() if device
is unplugged to prevent crash in GPU initialization failure") makes call to
amdgpu_device_unmap_mmio() conditioned on device unplugged. This patch unmaps
MMIO mappings even when device is not unplugged.

v2: Add condition of drm_dev_enter() to deleted unmaps in patch
"drm/amdgpu: Unmap all MMIO mappings"

Signed-off-by: Leslie Shi <Yuliang.Shi@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Enable second VCN for certain Navy Flounder.

Certain Navy Flounder cards have 2 VCNs, enable it.

Signed-off-by: Peng Ju Zhou <PengJu.Zhou@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: explicitly set is_dsc_supported to false before use

When UBSAN is enabled a case is shown on unplugging the display that
this variable hasn't been initialized by `update_dsc_caps`, presumably
when the display was unplugged it wasn't copied from the DPCD.

Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1956497
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Clear garbage data in err_data before usage

Memory of err_data should be cleaned before usage
when there're multiple entry in ras ih.
Otherwise garbage data from last loop will be used.

Signed-off-by: Jiawei Gu <Jiawei.Gu@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/i915/guc: Improve GuC loading status check/error reports

If the GuC fails to load, it is useful to know what firmware file /
version was attempted. So move the version info report to before the
load attempt rather than only after a successful load.

If the GuC does fail to load, then make the error messages visible
rather than being 'debug' prints that do not appears in dmesg output
by default.

When waiting for the GuC to load, it used to be necessary to check for
two different states - READY and (LAPIC_DONE | MIA_CORE). Apparently
the second signified init complete on RC6 exit. However, in more
recent GuC versions the RC6 exit sequence now finishes with status
READY as well. So the test can be simplified.

Also, add an enum giving all the current status codes that GuC loading
can report as a reference without having to pull and search through
the GuC source files.

Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220107000622.292081-4-John.C.Harrison@Intel.com

drm/i915/guc: Update to GuC version 69.0.3

Update to the latest GuC release.

The latest GuC firmware introduces a number of interface changes:

GuC may return NO_RESPONSE_RETRY message for requests sent over CTB.
Add support for this reply and try resending the request again as a
new CTB message.

A KLV (key-length-value) mechanism is now used for passing
configuration data such as CTB management.

With the new KLV scheme, the old CTB management actions are no longer
used and are removed.

Register capture on hang is now supported by GuC. Full i915 support
for this will be added by a later patch. A minimum support of
providing capture memory and register lists is required though, so add
that in.

The device id of the current platform needs to be provided at init time.

The 'poll CS' w/a (Wa_22012773006) was blanket enabled by previous
versions of GuC. It must now be explicitly requested by the KMD. So,
add in the code to turn it on when relevant.

The GuC log entry format has changed. This requires adding a new field
to the log header structure to mark the wrap point at the end of the
buffer (as the buffer size is no longer a multiple of the log entry
size).

New CTB notification messages are now sent for some things that were
previously only sent via MMIO notifications.

Of these, the crash dump notification was not really being handled by
i915. It called the log flush code but that only flushed the regular
debug log and then only if relay logging was enabled. So just report
an error message instead.

The 'exception' notification was just being ignored completely. So add
an error message for that as well.

Note that in either the crash dump or the exception case, the GuC is
basically dead. The KMD will detect this via the heartbeat and trigger
both an error log (which will include the crash dump as part of the
GuC log) and a GT reset. So no other processing is really required.

Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220107000622.292081-3-John.C.Harrison@Intel.com

drm/i915/guc: Temporarily bump the GuC load timeout

There is a known (but exceedingly unlikely) race condition where the
asynchronous frequency management code could reduce the GT clock while
a GuC reload is in progress (during a full GT reset). A fix is in
progress but there are complex locking issues to be resolved. In the
meantime bump the timeout to 200ms. Even at slowest clock, this
should be sufficient. And in the working case, a larger timeout makes
no difference.

Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220107000622.292081-2-John.C.Harrison@Intel.com

drm/atomic: Check new_crtc_state->active to determine if CRTC needs disable in self refresh mode

Actual hardware state of CRTC is controlled by the member 'active' in
struct drm_crtc_state instead of the member 'enable', according to the
kernel doc of the member 'enable'.  In fact, the drm client modeset
and atomic helpers are using the member 'active' to do the control.

Referencing the member 'enable' of new_crtc_state, the function
crtc_needs_disable() may fail to reflect if CRTC needs disable in
self refresh mode, e.g., when the framebuffer emulation will be blanked
through the client modeset helper with the next commit, the member
'enable' of new_crtc_state is still true while the member 'active' is
false, hence the relevant potential encoder and bridges won't be disabled.

So, let's check new_crtc_state->active to determine if CRTC needs disable
in self refresh mode instead of new_crtc_state->enable.

Fixes: 1452c25b0e60 ("drm: Add helpers to kick off self refresh mode in drivers")
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Rob Clark <robdclark@chromium.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211230040626.646807-1-victor.liu@nxp.com

drm/i915: Use struct vma_resource instead of struct vma_snapshot

There is always a struct vma_resource guaranteed to be alive when we
access a corresponding struct vma_snapshot.

So ditch the latter and instead of allocating vma_snapshots, reference
the already existning vma_resource.

This requires a couple of extra members in struct vma_resource but that's
a small price to pay for the simplification.

v2:
- Fix a missing include and declaration (kernel test robot <lkp@intel.com>)

Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220110172219.107131-7-thomas.hellstrom@linux.intel.com

drm/i915: Asynchronous migration selftest

Add a selftest to exercise asynchronous migration and -unbining.
Extend the gem_migrate selftest to perform the migrations while
depending on a spinner and a bound vma set up on the migrated
buffer object.

Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220110172219.107131-6-thomas.hellstrom@linux.intel.com

drm/i915: Use vma resources for async unbinding

Implement async (non-blocking) unbinding by not syncing the vma before
calling unbind on the vma_resource.
Add the resulting unbind fence to the object's dma_resv from where it is
picked up by the ttm migration code.
Ideally these unbind fences should be coalesced with the migration blit
fence to avoid stalling the migration blit waiting for unbind, as they
can certainly go on in parallel, but since we don't yet have a
reasonable data structure to use to coalesce fences and attach the
resulting fence to a timeline, we defer that for now.

Note that with async unbinding, even while the unbind waits for the
preceding bind to complete before unbinding, the vma itself might have been
destroyed in the process, clearing the vma pages. Therefore we can
only allow async unbinding if we have a refcounted sg-list and keep a
refcount on that for the vma resource pages to stay intact until
binding occurs. If this condition is not met, a request for an async
unbind is diverted to a sync unbind.

v2:
- Use a separate kmem_cache for vma resources for now to isolate their
  memory allocation and aid debugging.
- Move the check for vm closed to the actual unbinding thread. Regardless
  of whether the vm is closed, we need the unbind fence to properly wait
  for capture.
- Clear vma_res::vm on unbind and update its documentation.
v4:
- Take cache coloring into account when searching for vma resources
  pending unbind. (Matthew Auld)
v5:
- Fix timeout and error check in i915_vma_resource_bind_dep_await().
- Avoid taking a reference on the object for async binding if
  async unbind capable.
- Fix braces around a single-line if statement.
v6:
- Fix up the cache coloring adjustment. (Kernel test robot <lkp@intel.com>)
- Don't allow async unbinding if the vma_res pages are not the same as
  the object pages. (Matthew Auld)
v7:
- s/unsigned long/u64/ in a number of places (Matthew Auld)

Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220110172219.107131-5-thomas.hellstrom@linux.intel.com

drm/i915: Don't pin the object pages during pending vma binds

A pin-count is already held by vma->pages so taking an additional pin
during async binds is not necessary.

When we introduce async unbinding we have other means of keeping the
object pages alive.

Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220110172219.107131-4-thomas.hellstrom@linux.intel.com

drm/i915: Use the vma resource as argument for gtt binding / unbinding

When introducing asynchronous unbinding, the vma itself may no longer
be alive when the actual binding or unbinding takes place.

Update the gtt i915_vma_ops accordingly to take a struct i915_vma_resource
instead of a struct i915_vma for the bind_vma() and unbind_vma() ops.
Similarly change the insert_entries() op for struct i915_address_space.

Replace a couple of i915_vma_snapshot members with their newly introduced
i915_vma_resource counterparts, since they have the same lifetime.

Also make sure to avoid changing the struct i915_vma_flags (in particular
the bind flags) async. That should now only be done sync under the
vm mutex.

v2:
- Update the vma_res::bound_flags when binding to the aliased ggtt
v6:
- Remove I915_VMA_ALLOC_BIT (Matthew Auld)
- Change some members of struct i915_vma_resource from unsigned long to u64
  (Matthew Auld)
v7:
- Fix vma resource size parameters to be u64 rather than unsigned long
  (Matthew Auld)

Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220110172219.107131-3-thomas.hellstrom@linux.intel.com

drm/sun4i: dw-hdmi: Fix missing put_device() call in sun8i_hdmi_phy_get

The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore.
Add the corresponding 'put_device()' in the error handling path.

Fixes: 9bf3797796f5 ("drm/sun4i: dw-hdmi: Make HDMI PHY into a platform device")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220107083633.20843-1-linmq006@gmail.com

drm/i915: Initial introduction of vma resources

Introduce vma resources, sort of similar to TTM resources,  needed for
asynchronous bind management. Initially we will use them to hold
completion of unbinding when we capture data from a vma, but they will
be used extensively in upcoming patches for asynchronous vma unbinding.

v6:
- Some documentation updates

Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220110172219.107131-2-thomas.hellstrom@linux.intel.com

drm/i915/ttm: ensure we unmap when purging

Purging can happen during swapping out, or directly invoked with the
madvise ioctl. In such cases this doesn't involve a ttm move, which
skips umapping the object.

v2(Thomas):
- add ttm_truncate helper, and just call into i915_ttm_move_notify() to
  handle the unmapping step

Fixes: 213d50927763 ("drm/i915/ttm: Introduce a TTM i915 gem object backend")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220106174910.280616-4-matthew.auld@intel.com
(cherry picked from commit ab4911b7d411ab2ef3b38322178b9138e156c393)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915/ttm: add unmap_virtual callback

Ensure we call ttm_bo_unmap_virtual when releasing the pages.
Importantly this should now handle the ttm swapping case, and all other
places that already call into i915_ttm_move_notify().

v2: fix up the selftest

Fixes: cf3e3e86d779 ("drm/i915: Use ttm mmap handling for ttm bo's.")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220106174910.280616-3-matthew.auld@intel.com
(cherry picked from commit 903e0387270eef14a711c0feb23b7bf62d2480df)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915/ttm: only fault WILLNEED objects

Don't attempt to fault and re-populate purged objects. By some fluke
this passes the dontneed-after-mmap IGT, but for the wrong reasons.

Fixes: cf3e3e86d779 ("drm/i915: Use ttm mmap handling for ttm bo's.")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220106174910.280616-2-matthew.auld@intel.com
(cherry picked from commit f3cb4a2de5410147b53e53416a3af0ffe26b5f4e)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: don't call free_mmap_offset when purging

The TTM backend is in theory the only user here(also purge should only
be called once we have dropped the pages), where it is setup at object
creation and is only removed once the object is destroyed. Also
resetting the node here might be iffy since the ttm fault handler
uses the stored fake offset to determine the page offset within the pages
array.

This also blows up in the dontneed-before-mmap test, since the
expectation is that the vma_node will live on, until the object is
destroyed:

<2> [749.062902] kernel BUG at drivers/gpu/drm/i915/gem/i915_gem_ttm.c:943!
<4> [749.062923] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
<4> [749.062928] CPU: 0 PID: 1643 Comm: gem_madvise Tainted: G     U  W         5.16.0-rc8-CI-CI_DRM_11046+ #1
<4> [749.062933] Hardware name: Gigabyte Technology Co., Ltd. GB-Z390 Garuda/GB-Z390 Garuda-CF, BIOS IG1c 11/19/2019
<4> [749.062937] RIP: 0010:i915_ttm_mmap_offset.cold.35+0x5b/0x5d [i915]
<4> [749.063044] Code: 00 48 c7 c2 a0 23 4e a0 48 c7 c7 26 df 4a a0 e8 95 1d d0 e0 bf 01 00 00 00 e8 8b ec cf e0 31 f6 bf 09 00 00 00 e8 5f 30 c0 e0 <0f> 0b 48 c7 c1 24 4b 56 a0 ba 5b 03 00 00 48 c7 c6 c0 23 4e a0 48
<4> [749.063052] RSP: 0018:ffffc90002ab7d38 EFLAGS: 00010246
<4> [749.063056] RAX: 0000000000000240 RBX: ffff88811f2e61c0 RCX: 0000000000000006
<4> [749.063060] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000009
<4> [749.063063] RBP: ffffc90002ab7e58 R08: 0000000000000001 R09: 0000000000000001
<4> [749.063067] R10: 000000000123d0f8 R11: ffffc90002ab7b20 R12: ffff888112a1a000
<4> [749.063071] R13: 0000000000000004 R14: ffff88811f2e61c0 R15: ffff888112a1a000
<4> [749.063074] FS:  00007f6e5fcad500(0000) GS:ffff8884ad600000(0000) knlGS:0000000000000000
<4> [749.063078] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4> [749.063081] CR2: 00007efd264e39f0 CR3: 0000000115fd6005 CR4: 00000000003706f0
<4> [749.063085] Call Trace:
<4> [749.063087]  <TASK>
<4> [749.063089]  __assign_mmap_offset+0x41/0x300 [i915]
<4> [749.063171]  __assign_mmap_offset_handle+0x159/0x270 [i915]
<4> [749.063248]  ? i915_gem_dumb_mmap_offset+0x70/0x70 [i915]
<4> [749.063325]  drm_ioctl_kernel+0xae/0x140
<4> [749.063330]  drm_ioctl+0x201/0x3d0
<4> [749.063333]  ? i915_gem_dumb_mmap_offset+0x70/0x70 [i915]
<4> [749.063409]  ? do_user_addr_fault+0x200/0x670
<4> [749.063415]  __x64_sys_ioctl+0x6d/0xa0
<4> [749.063419]  do_syscall_64+0x3a/0xb0
<4> [749.063423]  entry_SYSCALL_64_after_hwframe+0x44/0xae
<4> [749.063428] RIP: 0033:0x7f6e5f100317

Testcase: igt/gem_madvise/dontneed-before-mmap
Fixes: cf3e3e86d779 ("drm/i915: Use ttm mmap handling for ttm bo's.")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220106174910.280616-1-matthew.auld@intel.com
(cherry picked from commit 658a0c632625e1db51837ff754fe18a6a7f2ccf8)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915/pxp: Hold RPM wakelock during PXP unbind

Similar to commit b8d8436840ca ("drm/i915/gt: Hold RPM wakelock during
PXP suspend") but to fix the same warning for unbind during shutdown:

------------[ cut here ]------------
RPM wakelock ref not held during HW access
WARNING: CPU: 0 PID: 4139 at drivers/gpu/drm/i915/intel_runtime_pm.h:115
gen12_fwtable_write32+0x1b7/0
Modules linked in: 8021q ccm rfcomm cmac algif_hash algif_skcipher
af_alg uinput snd_hda_codec_hdmi vf industrialio iwl7000_mac80211
cros_ec_sensorhub lzo_rle lzo_compress zram iwlwifi cfg80211 joydev
CPU: 0 PID: 4139 Comm: halt Tainted: G     U  W
5.10.84 #13 344e11e079c4a03940d949e537eab645f6
RIP: 0010:gen12_fwtable_write32+0x1b7/0x200
Code: 48 c7 c7 fc b3 b5 89 31 c0 e8 2c f3 ad ff 0f 0b e9 04 ff ff ff c6
05 71 e9 1d 01 01 48 c7 c7 d67
RSP: 0018:ffffa09ec0bb3bb0 EFLAGS: 00010246
RAX: 12dde97bbd260300 RBX: 00000000000320f0 RCX: ffffffff89e60ea0
RDX: 0000000000000000 RSI: 00000000ffffdfff RDI: ffffffff89e60e70
RBP: ffffa09ec0bb3bd8 R08: 0000000000000000 R09: ffffa09ec0bb3950
R10: 00000000ffffdfff R11: ffffffff89e91160 R12: 0000000000000000
R13: 0000000028121969 R14: ffff9515c32f0990 R15: 0000000040000000
FS:  0000790dcf225740(0000) GS:ffff951737800000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000058b25efae147 CR3: 0000000133ea6001 CR4: 0000000000770ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff07f0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
 intel_pxp_fini_hw+0x2f/0x39
 i915_pxp_tee_component_unbind+0x1c/0x42
 component_unbind+0x32/0x48
 component_unbind_all+0x80/0x9d
 take_down_master+0x24/0x36
 component_master_del+0x56/0x70
 mei_pxp_remove+0x2c/0x68
 mei_cl_device_remove+0x35/0x68
 device_release_driver_internal+0x100/0x1a1
 mei_cl_bus_remove_device+0x21/0x79
 mei_cl_bus_remove_devices+0x3b/0x51
 mei_stop+0x3b/0xae
 mei_me_shutdown+0x23/0x58
 device_shutdown+0x144/0x1d3
 kernel_power_off+0x13/0x4c
 __se_sys_reboot+0x1d4/0x1e9
 do_syscall_64+0x43/0x55
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x790dcf316273
Code: 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00
00 89 fa be 69 19 12 28 bf ad8
RSP: 002b:00007ffca0df9198 EFLAGS: 00000202 ORIG_RAX: 00000000000000a9
RAX: ffffffffffffffda RBX: 000000004321fedc RCX: 0000790dcf316273
RDX: 000000004321fedc RSI: 0000000028121969 RDI: 00000000fee1dead
RBP: 00007ffca0df9200 R08: 0000000000000007 R09: 0000563ce8cd8970
R10: 0000000000000000 R11: 0000000000000202 R12: 00007ffca0df9308
R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000003
---[ end trace 2f501b01b348f114 ]---
ACPI: Preparing to enter system sleep state S5
reboot: Power down

Changes since v1:
 - Rebase to latest drm-tip

Fixes: 0cfab4cb3c4e ("drm/i915/pxp: Enable PXP power management")
Suggested-by: Lee Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220106200236.489656-2-juston.li@intel.com
(cherry picked from commit 57ded5fc98b11d76dae505ca3591b61c9dbbbda7)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915/ttm: ensure we unmap when purging

Purging can happen during swapping out, or directly invoked with the
madvise ioctl. In such cases this doesn't involve a ttm move, which
skips umapping the object.

v2(Thomas):
- add ttm_truncate helper, and just call into i915_ttm_move_notify() to
  handle the unmapping step

Fixes: 213d50927763 ("drm/i915/ttm: Introduce a TTM i915 gem object backend")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220106174910.280616-4-matthew.auld@intel.com

drm/i915/ttm: add unmap_virtual callback

Ensure we call ttm_bo_unmap_virtual when releasing the pages.
Importantly this should now handle the ttm swapping case, and all other
places that already call into i915_ttm_move_notify().

v2: fix up the selftest

Fixes: cf3e3e86d779 ("drm/i915: Use ttm mmap handling for ttm bo's.")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220106174910.280616-3-matthew.auld@intel.com

drm/i915/ttm: only fault WILLNEED objects

Don't attempt to fault and re-populate purged objects. By some fluke
this passes the dontneed-after-mmap IGT, but for the wrong reasons.

Fixes: cf3e3e86d779 ("drm/i915: Use ttm mmap handling for ttm bo's.")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220106174910.280616-2-matthew.auld@intel.com

drm/i915: don't call free_mmap_offset when purging

The TTM backend is in theory the only user here(also purge should only
be called once we have dropped the pages), where it is setup at object
creation and is only removed once the object is destroyed. Also
resetting the node here might be iffy since the ttm fault handler
uses the stored fake offset to determine the page offset within the pages
array.

This also blows up in the dontneed-before-mmap test, since the
expectation is that the vma_node will live on, until the object is
destroyed:

<2> [749.062902] kernel BUG at drivers/gpu/drm/i915/gem/i915_gem_ttm.c:943!
<4> [749.062923] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
<4> [749.062928] CPU: 0 PID: 1643 Comm: gem_madvise Tainted: G     U  W         5.16.0-rc8-CI-CI_DRM_11046+ #1
<4> [749.062933] Hardware name: Gigabyte Technology Co., Ltd. GB-Z390 Garuda/GB-Z390 Garuda-CF, BIOS IG1c 11/19/2019
<4> [749.062937] RIP: 0010:i915_ttm_mmap_offset.cold.35+0x5b/0x5d [i915]
<4> [749.063044] Code: 00 48 c7 c2 a0 23 4e a0 48 c7 c7 26 df 4a a0 e8 95 1d d0 e0 bf 01 00 00 00 e8 8b ec cf e0 31 f6 bf 09 00 00 00 e8 5f 30 c0 e0 <0f> 0b 48 c7 c1 24 4b 56 a0 ba 5b 03 00 00 48 c7 c6 c0 23 4e a0 48
<4> [749.063052] RSP: 0018:ffffc90002ab7d38 EFLAGS: 00010246
<4> [749.063056] RAX: 0000000000000240 RBX: ffff88811f2e61c0 RCX: 0000000000000006
<4> [749.063060] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000009
<4> [749.063063] RBP: ffffc90002ab7e58 R08: 0000000000000001 R09: 0000000000000001
<4> [749.063067] R10: 000000000123d0f8 R11: ffffc90002ab7b20 R12: ffff888112a1a000
<4> [749.063071] R13: 0000000000000004 R14: ffff88811f2e61c0 R15: ffff888112a1a000
<4> [749.063074] FS:  00007f6e5fcad500(0000) GS:ffff8884ad600000(0000) knlGS:0000000000000000
<4> [749.063078] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4> [749.063081] CR2: 00007efd264e39f0 CR3: 0000000115fd6005 CR4: 00000000003706f0
<4> [749.063085] Call Trace:
<4> [749.063087]  <TASK>
<4> [749.063089]  __assign_mmap_offset+0x41/0x300 [i915]
<4> [749.063171]  __assign_mmap_offset_handle+0x159/0x270 [i915]
<4> [749.063248]  ? i915_gem_dumb_mmap_offset+0x70/0x70 [i915]
<4> [749.063325]  drm_ioctl_kernel+0xae/0x140
<4> [749.063330]  drm_ioctl+0x201/0x3d0
<4> [749.063333]  ? i915_gem_dumb_mmap_offset+0x70/0x70 [i915]
<4> [749.063409]  ? do_user_addr_fault+0x200/0x670
<4> [749.063415]  __x64_sys_ioctl+0x6d/0xa0
<4> [749.063419]  do_syscall_64+0x3a/0xb0
<4> [749.063423]  entry_SYSCALL_64_after_hwframe+0x44/0xae
<4> [749.063428] RIP: 0033:0x7f6e5f100317

Testcase: igt/gem_madvise/dontneed-before-mmap
Fixes: cf3e3e86d779 ("drm/i915: Use ttm mmap handling for ttm bo's.")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220106174910.280616-1-matthew.auld@intel.com

drm/i915: clean up shrinker_release_pages

Add some proper flags for the different modes, and shorten the name to
something more snappy.

Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211215110746.865-2-matthew.auld@intel.com

drm/i915: remove writeback hook

Ditch the writeback hook and drop i915_gem_object_writeback(). We
already support the shrinker_release_pages hook which can just call
shmem_writeback directly.

Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211215110746.865-1-matthew.auld@intel.com

drm/i915/pxp: Hold RPM wakelock during PXP unbind

Similar to commit b8d8436840ca ("drm/i915/gt: Hold RPM wakelock during
PXP suspend") but to fix the same warning for unbind during shutdown:

------------[ cut here ]------------
RPM wakelock ref not held during HW access
WARNING: CPU: 0 PID: 4139 at drivers/gpu/drm/i915/intel_runtime_pm.h:115
gen12_fwtable_write32+0x1b7/0
Modules linked in: 8021q ccm rfcomm cmac algif_hash algif_skcipher
af_alg uinput snd_hda_codec_hdmi vf industrialio iwl7000_mac80211
cros_ec_sensorhub lzo_rle lzo_compress zram iwlwifi cfg80211 joydev
CPU: 0 PID: 4139 Comm: halt Tainted: G     U  W
5.10.84 #13 344e11e079c4a03940d949e537eab645f6
RIP: 0010:gen12_fwtable_write32+0x1b7/0x200
Code: 48 c7 c7 fc b3 b5 89 31 c0 e8 2c f3 ad ff 0f 0b e9 04 ff ff ff c6
05 71 e9 1d 01 01 48 c7 c7 d67
RSP: 0018:ffffa09ec0bb3bb0 EFLAGS: 00010246
RAX: 12dde97bbd260300 RBX: 00000000000320f0 RCX: ffffffff89e60ea0
RDX: 0000000000000000 RSI: 00000000ffffdfff RDI: ffffffff89e60e70
RBP: ffffa09ec0bb3bd8 R08: 0000000000000000 R09: ffffa09ec0bb3950
R10: 00000000ffffdfff R11: ffffffff89e91160 R12: 0000000000000000
R13: 0000000028121969 R14: ffff9515c32f0990 R15: 0000000040000000
FS:  0000790dcf225740(0000) GS:ffff951737800000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000058b25efae147 CR3: 0000000133ea6001 CR4: 0000000000770ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff07f0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
 intel_pxp_fini_hw+0x2f/0x39
 i915_pxp_tee_component_unbind+0x1c/0x42
 component_unbind+0x32/0x48
 component_unbind_all+0x80/0x9d
 take_down_master+0x24/0x36
 component_master_del+0x56/0x70
 mei_pxp_remove+0x2c/0x68
 mei_cl_device_remove+0x35/0x68
 device_release_driver_internal+0x100/0x1a1
 mei_cl_bus_remove_device+0x21/0x79
 mei_cl_bus_remove_devices+0x3b/0x51
 mei_stop+0x3b/0xae
 mei_me_shutdown+0x23/0x58
 device_shutdown+0x144/0x1d3
 kernel_power_off+0x13/0x4c
 __se_sys_reboot+0x1d4/0x1e9
 do_syscall_64+0x43/0x55
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x790dcf316273
Code: 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00
00 89 fa be 69 19 12 28 bf ad8
RSP: 002b:00007ffca0df9198 EFLAGS: 00000202 ORIG_RAX: 00000000000000a9
RAX: ffffffffffffffda RBX: 000000004321fedc RCX: 0000790dcf316273
RDX: 000000004321fedc RSI: 0000000028121969 RDI: 00000000fee1dead
RBP: 00007ffca0df9200 R08: 0000000000000007 R09: 0000563ce8cd8970
R10: 0000000000000000 R11: 0000000000000202 R12: 00007ffca0df9308
R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000003
---[ end trace 2f501b01b348f114 ]---
ACPI: Preparing to enter system sleep state S5
reboot: Power down

Changes since v1:
 - Rebase to latest drm-tip

Fixes: 0cfab4cb3c4e ("drm/i915/pxp: Enable PXP power management")
Suggested-by: Lee Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220106200236.489656-2-juston.li@intel.com

drm/amd/display: Add version check before using DP alt query interface

[Why]
To maintain compatibility with firmware older than 4.0.11.

Those firmware may have interrmittent hangs with RDCSPIPE or the PHY,
but we shouldn't regress their previous behavior.

[How]
Use the new path if firmware is development or 4.0.11 or newer. Use the
legacy path otherwise.

Fixes: 41f91315b5be5a ("drm/amd/display: Query DMCUB for dp alt status")

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: introduce mpo detection flags

[why]
We want to know if new crtc state is enabling MPO configuration before
enabling it.
[how]
Detect if both primary and overlay planes are enabled on the same CRTC.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add check for forced_clocks debug option

[why]
driver missed the check.

[how]
add the check.
add min display clock = 100mhz check based on dccg doc.

[note]
add SetPhyclkVoltageByFreq as confirmed with smu, but not enabled in
this change.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Don't reinitialize DMCUB on s0ix resume

[Why]
PSP will suspend and resume DMCUB. Driver should just wait for DMCUB to
finish the auto load before continuining instead of placing it into
reset, wiping its firmware state and reinitializing.

If we don't let DMCUB fully finish initializing for S0ix then some state
will be lost and screen corruption can occur due to incorrect address
translation.

[How]
Use dmub_srv callbacks to determine in DMCUB is running and wait for
auto-load to complete before continuining.

In S0ix DMCUB will be running and DAL fw so initialize will skip.

In S3 DMCUB will not be running and we will do a full hardware init.

In S3 DMCUB will be running but will not be DAL fw so we will also do
a full hardware init.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: unhard code link to phy idx mapping in dc link and clean up

[why]
1. Current code hard codes link to PHY mapping in dc link level per asic
per revision.
This is not scalable. In long term the mapping will be obatined from
DMUB and store in dc resource.

2. Depending on DCN revision and endpoint type, the definition of
dio_output_idx dio_output_type and phy_idx are not  consistent. We need
to unify the meaning of these hardware indices across different system
configuration.

[how]
1. Temporarly move the hardcoded mapping to dc_resource level, which
should have full awareness of asic specific configuration and add a TODO
comment to move the mapping to DMUB.

2. populate dio_output_idx/phy_idx for all configuration, define
usb4_enabled bit instead of dio_output_type as an external enum.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix underflow for fused display pipes case

[Why]
Depend on res_pool->res_cap->num_timing_generator to query timing
gernerator information, it would case underflow at the fused display
pipes case.
Due to the res_pool->res_cap->num_timing_generator records default
timing generator resource built in driver, not the current chip.

[How]
Some ASICs would be fused display pipes less than the default setting.
In dcnxx_resource_construct function, driver would obatin real timing
generator count and store it into res_pool->timing_generator_count.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: don't set s3 and s0ix at the same time

This makes it clearer which codepaths are in use specifically in
one state or the other.

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: explicitly check for s0ix when evicting resources

This codepath should be running in both s0ix and s3, but only does
currently because s3 and s0ix are both set in the s0ix case.

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/pm: keep the BACO feature enabled for suspend

To pair with the workaround which always reset the ASIC in suspend.
Otherwise, the reset which relies on BACO will fail.

Fixes: daf8de0874ab5b ("drm/amdgpu: always reset the asic in suspend (v2)")

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add dummy event6 for vega10

[why]
Malicious mailbox event1 fails driver loading on vega10.
A dummy event6 prevent driver from taking response from malicious event1 as its own.

[how]
On vega10, send a mailbox event6 before sending event1.

Signed-off-by: James Yao <yiqing.yao@amd.com>
Reviewed-by: Jingwen Chen <Jingwen.Chen2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: enable sdma ecc interrupt event can be handled by event_interrupt_wq_v9

Enable sdma ecc interrupt event can be handled by event_interrupt_wq_v9.

Signed-off-by: yipechai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/i915: Remove unused i915->ggtt

The reference to the GGTT from the private date is not used
anymore. Remove it.

The ggtt in the root gt will now be dynamically allocated and the
deallocation handled by the drmm_* managed allocation.

Suggested-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Sujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211219212500.61432-7-andi.shyti@linux.intel.com

drm/i915/selftests: Use to_gt() helper for GGTT accesses

GGTT is currently available both through i915->ggtt and gt->ggtt, and we
eventually want to get rid of the i915->ggtt one.
Use to_gt() for all i915->ggtt accesses to help with the future
refactoring.

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Sujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211219212500.61432-6-andi.shyti@linux.intel.com

drm/i915/display: Use to_gt() helper for GGTT accesses

GGTT is currently available both through i915->ggtt and gt->ggtt, and we
eventually want to get rid of the i915->ggtt one.
Use to_gt() for all i915->ggtt accesses to help with the future
refactoring.

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Sujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211219212500.61432-5-andi.shyti@linux.intel.com

drm/i915/gem: Use to_gt() helper for GGTT accesses

GGTT is currently available both through i915->ggtt and gt->ggtt, and we
eventually want to get rid of the i915->ggtt one.
Use to_gt() for all i915->ggtt accesses to help with the future
refactoring.

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Sujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211219212500.61432-4-andi.shyti@linux.intel.com

drm/i915: Use to_gt() helper for GGTT accesses

GGTT is currently available both through i915->ggtt and gt->ggtt, and we
eventually want to get rid of the i915->ggtt one.
Use to_gt() for all i915->ggtt accesses to help with the future
refactoring.

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220104223550.56135-1-andi.shyti@linux.intel.com

drm/i915/gt: Use to_gt() helper for GGTT accesses

GGTT is currently available both through i915->ggtt and gt->ggtt, and we
eventually want to get rid of the i915->ggtt one.
Use to_gt() for all i915->ggtt accesses to help with the future
refactoring.

During the probe of i915 the early intiialization of the gt
(intel_gt_init_hw_early()) is moved prior to any access to the
ggtt. This because it's in that moment we assign the ggtt to the
gt and we want to do that before using it.

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Sujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211221195946.3180-1-andi.shyti@linux.intel.com

drm/i915/gem: Use local pointer ttm for __i915_ttm_move

Using local pointer ttm as argument in  __i915_ttm_move instead of bo->ttm,
as local pointer was previously assigned to bo->ttm in function.
This will make code a bit more readable.

Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Signed-off-by: Jasmine Newsome <jasmine.newsome@intel.com>
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220104203642.231878-1-jasmine.newsome@intel.com

dt-bindings: display: meson-dw-hdmi: add missing sound-name-prefix property

This is used in meson-gx and meson-g12. Add the property to the binding.
This fixes the dtschema warning:
hdmi-tx@c883a000: 'sound-name-prefix' does not match any of the
regexes: 'pinctrl-[0-9]+'

Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Fixes: 376bf52deef5 ("dt-bindings: display: amlogic, meson-dw-hdmi: convert to yaml")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211223122434.39378-2-alexander.stein@mailbox.org

dt-bindings: display: meson-vpu: Add missing amlogic,canvas property

This property was already mentioned in the old textual bindings
amlogic,meson-vpu.txt, but got dropped during conversion.
Adding it back similar to amlogic,gx-vdec.yaml.

Fixes: 6b9ebf1e0e67 ("dt-bindings: display: amlogic, meson-vpu: convert to yaml")
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211219094155.177206-1-alexander.stein@mailbox.org