OSDN Git Service
Florian Fainelli [Tue, 11 Nov 2014 02:06:21 +0000 (18:06 -0800)]
net: bcmgenet: apply MII configuration in bcmgenet_open()
In case an interface has been brought down before entering S3, and then
brought up out of S3, all the initialization done during
bcmgenet_probe() by bcmgenet_mii_init() calling bcmgenet_mii_config() is
just lost since register contents are restored to their reset values.
Re-apply this configuration anytime we call bcmgenet_open() to make sure
our port multiplexer is properly configured to match the PHY interface.
Since we are now calling bcmgenet_mii_config() everytime bcmgenet_open()
is called, make sure we only print the message during initialization
time not to pollute the console.
Fixes:
b6e978e50444 ("net: bcmgenet: add suspend/resume callbacks")
Fixes:
1c1008c793fa4 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 11 Nov 2014 02:06:20 +0000 (18:06 -0800)]
net: bcmgenet: connect and disconnect from the PHY state machine
phy_disconnect() is the only way to guarantee that we are not going to
schedule more work on the PHY state machine workqueue for that
particular PHY device.
This fixes an issue where a network interface was suspended prior to a
system suspend/resume cycle and would then be resumed as part of
mdio_bus_resume(), since the GENET interface clocks would have been
disabled, this basically resulted in bus errors to appear since we are
invoking the GENET driver adjust_link() callback.
Fixes:
b6e978e50444 ("net: bcmgenet: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Wahren [Tue, 11 Nov 2014 22:38:00 +0000 (22:38 +0000)]
net: qualcomm: Fix dependency
This patch removes the dependency of the VENDOR entry and fixes
the QCA7000 one.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 11 Nov 2014 18:22:05 +0000 (10:22 -0800)]
ixgbe: phy: fix uninitialized status in ixgbe_setup_phy_link_tnx
Status variable is never initialized, can carry an arbitrary value
on the stack and thus may let the function fail.
Fixes:
e90dd2645664 ("ixgbe: Make return values more direct")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brian Hill [Tue, 11 Nov 2014 20:39:39 +0000 (13:39 -0700)]
net: phy: Correctly handle MII ioctl which changes autonegotiation.
When advertised capabilities are changed with mii-tool, such as:
mii-tool -A 10baseT
the existing handler has two errors.
- An actual PHY register value is provided by mii-tool, and this
must be mapped to internal state with mii_adv_to_ethtool_adv_t().
- The PHY state machine needs to be told that autonegotiation has
again been performed. If not, the MAC will not be notified of
the new link speed and duplex, resulting in a possible config
mismatch.
Signed-off-by: Brian Hill <Brian@houston-radar.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 11 Nov 2014 01:54:25 +0000 (17:54 -0800)]
ipv6: fix IPV6_PKTINFO with v4 mapped
Use IS_ENABLED(CONFIG_IPV6), to enable this code if IPv6 is
a module.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes:
c8e6ad0829a7 ("ipv6: honor IPV6_PKTINFO with v4 mapped addresses on sendmsg")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 10 Nov 2014 17:00:09 +0000 (18:00 +0100)]
net: sctp: fix memory leak in auth key management
A very minimal and simple user space application allocating an SCTP
socket, setting SCTP_AUTH_KEY setsockopt(2) on it and then closing
the socket again will leak the memory containing the authentication
key from user space:
unreferenced object 0xffff8800837047c0 (size 16):
comm "a.out", pid 2789, jiffies
4296954322 (age 192.258s)
hex dump (first 16 bytes):
01 00 00 00 04 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<
ffffffff816d7e8e>] kmemleak_alloc+0x4e/0xb0
[<
ffffffff811c88d8>] __kmalloc+0xe8/0x270
[<
ffffffffa0870c23>] sctp_auth_create_key+0x23/0x50 [sctp]
[<
ffffffffa08718b1>] sctp_auth_set_key+0xa1/0x140 [sctp]
[<
ffffffffa086b383>] sctp_setsockopt+0xd03/0x1180 [sctp]
[<
ffffffff815bfd94>] sock_common_setsockopt+0x14/0x20
[<
ffffffff815beb61>] SyS_setsockopt+0x71/0xd0
[<
ffffffff816e58a9>] system_call_fastpath+0x12/0x17
[<
ffffffffffffffff>] 0xffffffffffffffff
This is bad because of two things, we can bring down a machine from
user space when auth_enable=1, but also we would leave security sensitive
keying material in memory without clearing it after use. The issue is
that sctp_auth_create_key() already sets the refcount to 1, but after
allocation sctp_auth_set_key() does an additional refcount on it, and
thus leaving it around when we free the socket.
Fixes:
65b07e5d0d0 ("[SCTP]: API updates to suport SCTP-AUTH extensions.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 10 Nov 2014 16:54:26 +0000 (17:54 +0100)]
net: sctp: fix NULL pointer dereference in af->from_addr_param on malformed packet
An SCTP server doing ASCONF will panic on malformed INIT ping-of-death
in the form of:
------------ INIT[PARAM: SET_PRIMARY_IP] ------------>
While the INIT chunk parameter verification dissects through many things
in order to detect malformed input, it misses to actually check parameters
inside of parameters. E.g. RFC5061, section 4.2.4 proposes a 'set primary
IP address' parameter in ASCONF, which has as a subparameter an address
parameter.
So an attacker may send a parameter type other than SCTP_PARAM_IPV4_ADDRESS
or SCTP_PARAM_IPV6_ADDRESS, param_type2af() will subsequently return 0
and thus sctp_get_af_specific() returns NULL, too, which we then happily
dereference unconditionally through af->from_addr_param().
The trace for the log:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000078
IP: [<
ffffffffa01e9c62>] sctp_process_init+0x492/0x990 [sctp]
PGD 0
Oops: 0000 [#1] SMP
[...]
Pid: 0, comm: swapper Not tainted 2.6.32-504.el6.x86_64 #1 Bochs Bochs
RIP: 0010:[<
ffffffffa01e9c62>] [<
ffffffffa01e9c62>] sctp_process_init+0x492/0x990 [sctp]
[...]
Call Trace:
<IRQ>
[<
ffffffffa01f2add>] ? sctp_bind_addr_copy+0x5d/0xe0 [sctp]
[<
ffffffffa01e1fcb>] sctp_sf_do_5_1B_init+0x21b/0x340 [sctp]
[<
ffffffffa01e3751>] sctp_do_sm+0x71/0x1210 [sctp]
[<
ffffffffa01e5c09>] ? sctp_endpoint_lookup_assoc+0xc9/0xf0 [sctp]
[<
ffffffffa01e61f6>] sctp_endpoint_bh_rcv+0x116/0x230 [sctp]
[<
ffffffffa01ee986>] sctp_inq_push+0x56/0x80 [sctp]
[<
ffffffffa01fcc42>] sctp_rcv+0x982/0xa10 [sctp]
[<
ffffffffa01d5123>] ? ipt_local_in_hook+0x23/0x28 [iptable_filter]
[<
ffffffff8148bdc9>] ? nf_iterate+0x69/0xb0
[<
ffffffff81496d10>] ? ip_local_deliver_finish+0x0/0x2d0
[<
ffffffff8148bf86>] ? nf_hook_slow+0x76/0x120
[<
ffffffff81496d10>] ? ip_local_deliver_finish+0x0/0x2d0
[...]
A minimal way to address this is to check for NULL as we do on all
other such occasions where we know sctp_get_af_specific() could
possibly return with NULL.
Fixes:
d6de3097592b ("[SCTP]: Add the handling of "Set Primary IP Address" parameter to INIT")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai [Mon, 10 Nov 2014 10:50:21 +0000 (11:50 +0100)]
net: ppp: Don't call bpf_prog_create() in ppp_lock
In ppp_ioctl(), bpf_prog_create() is called inside ppp_lock, which
eventually calls vmalloc() and hits BUG_ON() in vmalloc.c. This patch
works around the problem by moving the allocation outside the lock.
The bug was revealed by the recent change in net/core/filter.c, as it
allocates via vmalloc() instead of kmalloc() now.
Reported-and-tested-by: Stefan Seyfried <stefan.seyfried@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Sun, 9 Nov 2014 12:25:39 +0000 (14:25 +0200)]
net/mlx4_en: Advertize encapsulation offloads features only when VXLAN tunnel is set
Currenly we only support Large-Send and TX checksum offloads for
encapsulated traffic of type VXLAN. We must make sure to advertize
these offloads up to the stack only when VXLAN tunnel is set.
Failing to do so, would mislead the the networking stack to assume
that the driver can offload the internal TX checksum for GRE packets
and other buggy schemes.
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anish Bhatt [Fri, 7 Nov 2014 23:41:21 +0000 (15:41 -0800)]
cxgb4 : Fix bug in DCB app deletion
Unlike CEE, IEEE has a bespoke app delete call and does not rely on priority
for app deletion
Fixes :
2376c879b80c ('cxgb4 : Improve handling of DCB negotiation or loss
thereof')
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross [Mon, 10 Nov 2014 19:45:13 +0000 (11:45 -0800)]
udptunnel: Add SKB_GSO_UDP_TUNNEL during gro_complete.
When doing GRO processing for UDP tunnels, we never add
SKB_GSO_UDP_TUNNEL to gso_type - only the type of the inner protocol
is added (such as SKB_GSO_TCPV4). The result is that if the packet is
later resegmented we will do GSO but not treat it as a tunnel. This
results in UDP fragmentation of the outer header instead of (i.e.) TCP
segmentation of the inner header as was originally on the wire.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 10 Nov 2014 19:15:09 +0000 (14:15 -0500)]
Merge branch 'cxgb4-net'
Hariprasad Shenai says:
====================
cxgb4/cxgb4vf: Misc. fixes for cxgb4vf
For T5 use Packing and Padding Boundaries for SGE DMA transfers, move
fl_starve_thres to adpater structure, since they are different for each
adapter. The cxgb4vf driver's Free List Starvation Threshold needs to be larger
than the SGE's Egress Congestion Threshold or we'll end up in a mutual stall
where the driver waits for Ingress Packets to drive replacing Free List
Pointers and the SGE waits for Free List Pointers before pushing Ingress
Packets to the host.
The patches series is created against 'net' tree.
And includes patches on cxgb4 and cxgb4vf driver.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 7 Nov 2014 11:36:31 +0000 (17:06 +0530)]
cxgb4vf: FL Starvation Threshold needs to be larger than the SGE's Egress Congestion Threshold
Free List Starvation Threshold needs to be larger than the SGE's Egress
Congestion Threshold or we'll end up in a mutual stall where the driver waits
for Ingress Packets to drive replacing Free List Pointers and the SGE waits for
Free List Pointers before pushing Ingress Packets to the host.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 7 Nov 2014 11:36:30 +0000 (17:06 +0530)]
cxgb4/cxgb4vf: For T5 use Packing and Padding Boundaries for SGE DMA transfers
T5 introduces the ability to have separate Packing and Padding Boundaries
for SGE DMA transfers from the chip to Host Memory. This change set takes
advantage of that to set up a smaller Padding Boundary to conserve PCI Link
and Memory Bandwidth with T5.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 7 Nov 2014 11:36:29 +0000 (17:06 +0530)]
cxgb4vf: Move fl_starv_thres into adapter->sge data structure
Move fl_starv_thres into adapter->sge data structure since it
_could_ be different from adapter to adapter. Also move other per-adapter
SGE values which had been treated as driver globals into adapter->sge.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Charles Keepax [Thu, 6 Nov 2014 15:49:41 +0000 (15:49 +0000)]
asix: Do full reset during ax88772_bind
commit
3cc81d85ee01 ("asix: Don't reset PHY on if_up for ASIX 88772")
causes the ethernet on Arndale to no longer function. This appears to
be because the Arndale ethernet requires a full reset before it will
function correctly, however simply reverting the above patch causes
problems with ethtool settings getting reset.
It seems the problem is that the ethernet is not properly reset during
bind, and indeed the code in ax88772_bind that resets the device is a
very small subset of the actual ax88772_reset function. This patch uses
ax88772_reset in place of the existing reset code in ax88772_bind which
removes some code duplication and fixes the ethernet on Arndale.
It is still possible that the original patch causes some issues with
suspend and resume but that seems like a separate issue and I haven't
had a chance to test that yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lothar Waßmann [Fri, 7 Nov 2014 09:02:47 +0000 (10:02 +0100)]
net: fec: fix regression on i.MX28 introduced by rx_copybreak support
commit
1b7bde6d659d ("net: fec: implement rx_copybreak to improve rx performance")
introduced a regression for i.MX28. The swap_buffer() function doing
the endian conversion of the received data on i.MX28 may access memory
beyond the actual packet size in the DMA buffer. fec_enet_copybreak()
does not copy those bytes, so that the last bytes of a packet may be
filled with invalid data after swapping.
This will likely lead to checksum errors on received packets.
E.g. when trying to mount an NFS rootfs:
UDP: bad checksum. From 192.168.1.225:111 to 192.168.100.73:44662 ulen 36
Do the byte swapping and copying to the new skb in one go if
necessary.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 7 Nov 2014 03:15:20 +0000 (22:15 -0500)]
Merge tag 'master-2014-11-04' of git://git./linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-11-06
Please pull this batch of fixes intended for the 3.18 stream...
For the mac80211 bits, Johannes says:
"This contains another small set of fixes for 3.18, these are all
over the place and most of the bugs are old, one even dates back
to the original mac80211 we merged into the kernel."
For the iwlwifi bits, Emmanuel says:
"I fix here two issues that are related to the firmware
loading flow. A user reported that he couldn't load the
driver because the rfkill line was pulled up while we
were running the calibrations. This was happening while
booting the system: systemd was restoring the "disable
wifi settings" and that raised an RFKILL interrupt during
the calibration. Our driver didn't handle that properly
and this is now fixed."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Thu, 6 Nov 2014 12:58:51 +0000 (07:58 -0500)]
netxen: Fix link event handling.
o Poll for the link events only if firmware doesn't have capability
to notify the driver for the link events.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Govindarajulu Varadarajan [Thu, 6 Nov 2014 09:51:39 +0000 (15:21 +0530)]
enic: update desc properly in rx_copybreak
When we reuse the rx buffer, we need to update the desc. If not hardware sees
stale value.
In the following crash, when mtu is changed, hardware sees old rx buffer value
and crashes on skb_put.
Fix this by using enic_queue_rq_desc helper function which updates the necessary
desc.
[ 64.657376] skbuff: skb_over_panic: text:
ffffffffa041f55d len:9010 put:9010 head:
ffff8800d3ca9fc0 data:
ffff8800d3caa000 tail:0x2372 end:0x640 dev:enp0s3
[ 64.659965] ------------[ cut here ]------------
[ 64.661322] kernel BUG at net/core/skbuff.c:100!
[ 64.662644] invalid opcode: 0000 [#1] PREEMPT SMP
[ 64.664001] Modules linked in: rpcsec_gss_krb5 auth_rpcgss oid_registry nfsv4 cirrus ttm drm_kms_helper drm enic psmouse microcode evdev serio_raw syscopyarea sysfillrect sysimgblt i2c_piix4 i2c_core pcspkr nfs lockd grace sunrpc fscache ext4 crc16 mbcache jbd2 sd_mod ata_generic virtio_balloon ata_piix libata uhci_hcd virtio_pci virtio_ring usbcore usb_common virtio scsi_mod
[ 64.664834] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W
3.17.0-netnext-10335-g942396b-dirty #273
[ 64.664834] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 64.664834] task:
ffffffff81a1d580 ti:
ffffffff81a00000 task.ti:
ffffffff81a00000
[ 64.664834] RIP: 0010:[<
ffffffff81392cf1>] [<
ffffffff81392cf1>] skb_panic+0x61/0x70
[ 64.664834] RSP: 0018:
ffff880210603d48 EFLAGS:
00010292
[ 64.664834] RAX:
000000000000008c RBX:
ffff88020b0f6930 RCX:
0000000000000000
[ 64.664834] RDX:
000000000000008c RSI:
ffffffff8178b288 RDI:
00000000ffffffff
[ 64.664834] RBP:
ffff880210603d68 R08:
0000000000000001 R09:
0000000000000001
[ 64.664834] R10:
00000000000005ce R11:
0000000000000001 R12:
ffff88020b1f0b40
[ 64.664834] R13:
000000000000a332 R14:
ffff880209a1a000 R15:
0000000000000001
[ 64.664834] FS:
0000000000000000(0000) GS:
ffff880210600000(0000) knlGS:
0000000000000000
[ 64.664834] CS: 0010 DS: 0000 ES: 0000 CR0:
000000008005003b
[ 64.664834] CR2:
00007f6752935e48 CR3:
0000000035743000 CR4:
00000000000006f0
[ 64.664834] Stack:
[ 64.664834]
ffff8800d3caa000 0000000000002372 0000000000000640 ffff88020b1f0000
[ 64.664834]
ffff880210603d78 ffffffff81392d54 ffff880210603e08 ffffffffa041f55d
[ 64.664834]
0000000000000296 ffffffff00000000 00008e7e00008e7e ffff880200002332
[ 64.664834] Call Trace:
[ 64.664834] <IRQ>
[ 64.664834]
[ 64.664834] [<
ffffffff81392d54>] skb_put+0x54/0x60
[ 64.664834] [<
ffffffffa041f55d>] enic_rq_service.constprop.47+0x3ad/0x730 [enic]
[ 64.664834] [<
ffffffffa041fa79>] enic_poll_msix_rq+0x199/0x370 [enic]
[ 64.664834] [<
ffffffff813a5499>] net_rx_action+0x139/0x210
[ 64.664834] [<
ffffffff81290db3>] ? __this_cpu_preempt_check+0x13/0x20
[ 64.664834] [<
ffffffff8106110e>] __do_softirq+0x14e/0x280
[ 64.664834] [<
ffffffff8106152e>] irq_exit+0x8e/0xb0
[ 64.664834] [<
ffffffff8100fd21>] do_IRQ+0x61/0x100
[ 64.664834] [<
ffffffff814a2bf2>] common_interrupt+0x72/0x72
fixes:
a03bb56e67c357980dae886683733dab5583dc14 ("enic: implement rx_copybreak")
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Govindarajulu Varadarajan [Thu, 6 Nov 2014 09:51:38 +0000 (15:21 +0530)]
enic: handle error condition properly in enic_rq_indicate_buf
In case of error in rx path, we free the buf->os_buf but we do not make it NULL.
In next iteration we use the skb which is already freed. This causes the
following crash.
[ 886.154772] general protection fault: 0000 [#1] PREEMPT SMP
[ 886.154851] Modules linked in: rpcsec_gss_krb5 auth_rpcgss oid_registry nfsv4 microcode evdev cirrus ttm drm_kms_helper drm enic syscopyarea sysfillrect sysimgblt psmouse i2c_piix4 serio_raw pcspkr i2c_core nfs lockd grace sunrpc fscache ext4 crc16 mbcache jbd2 sd_mod crc_t10dif crct10dif_common ata_generic ata_piix virtio_balloon libata scsi_mod uhci_hcd usbcore virtio_pci virtio_ring virtio usb_common
[ 886.155199] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W
3.17.0-netnext-05668-g876bc7f #272
[ 886.155263] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 886.155304] task:
ffffffff81a1d580 ti:
ffffffff81a00000 task.ti:
ffffffff81a00000
[ 886.155356] RIP: 0010:[<
ffffffff81384030>] [<
ffffffff81384030>] kfree_skb_list+0x10/0x30
[ 886.155418] RSP: 0018:
ffff880210603d48 EFLAGS:
00010206
[ 886.155456] RAX:
0000000000000020 RBX:
0000000000000000 RCX:
0000000000000000
[ 886.155504] RDX:
0000000000000000 RSI:
0000000000000001 RDI:
004500084e000017
[ 886.155553] RBP:
ffff880210603d50 R08:
00000000fe13d1b6 R09:
0000000000000001
[ 886.155601] R10:
0000000000000000 R11:
0000000000000000 R12:
ffff880209ff2f00
[ 886.155650] R13:
ffff88020ac0fe40 R14:
ffff880209ff2f00 R15:
ffff8800da8e3a80
[ 886.155699] FS:
0000000000000000(0000) GS:
ffff880210600000(0000) knlGS:
0000000000000000
[ 886.155774] CS: 0010 DS: 0000 ES: 0000 CR0:
000000008005003b
[ 886.155814] CR2:
00007f0e0c925000 CR3:
0000000035e8b000 CR4:
00000000000006f0
[ 886.155865] Stack:
[ 886.155882]
0000000000000000 ffff880210603d78 ffffffff81383f79 ffff880209ff2f00
[ 886.155942]
ffff88020b0c0b40 000000000000c000 ffff880210603d90 ffffffff81383faf
[ 886.156001]
ffff880209ff2f00 ffff880210603da8 ffffffff8138406d ffff88020b1b08c0
[ 886.156061] Call Trace:
[ 886.156080] <IRQ>
[ 886.156095]
[ 886.156112] [<
ffffffff81383f79>] skb_release_data+0xa9/0xc0
[ 886.157656] [<
ffffffff81383faf>] skb_release_all+0x1f/0x30
[ 886.159195] [<
ffffffff8138406d>] consume_skb+0x1d/0x40
[ 886.160719] [<
ffffffff813942e5>] __dev_kfree_skb_any+0x35/0x40
[ 886.162224] [<
ffffffffa02dc1d5>] enic_rq_service.constprop.47+0xe5/0x5a0 [enic]
[ 886.163756] [<
ffffffffa02dc829>] enic_poll_msix_rq+0x199/0x370 [enic]
[ 886.164730] [<
ffffffff81397e29>] net_rx_action+0x139/0x210
[ 886.164730] [<
ffffffff8105fb2e>] __do_softirq+0x14e/0x280
[ 886.164730] [<
ffffffff8105ff2e>] irq_exit+0x8e/0xb0
[ 886.164730] [<
ffffffff8100fc1d>] do_IRQ+0x5d/0x100
[ 886.164730] [<
ffffffff81496832>] common_interrupt+0x72/0x72
fixes:
a03bb56e67c357980dae886683733dab5583dc14 ("enic: implement rx_copybreak")
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 6 Nov 2014 21:40:47 +0000 (16:40 -0500)]
Merge branch 'mlx5-net'
Eli Cohen says:
====================
mlx5_core fixes for 3.18
the following two patches fix races to could lead to kernel panic in some cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Thu, 6 Nov 2014 10:51:22 +0000 (12:51 +0200)]
net/mlx5_core: Fix race on driver load
When events arrive at driver load, the event handler gets called even before
the spinlock and list are initialized. Fix this by moving the initialization
before EQs creation.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Thu, 6 Nov 2014 10:51:21 +0000 (12:51 +0200)]
net/mlx5_core: Fix race in create EQ
After the EQ is created, it can possibly generate interrupts and the interrupt
handler is referencing eq->dev. It is therefore required to set eq->dev before
calling request_irq() so if an event is generated before request_irq() returns,
we will have a valid eq->dev field.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 5 Nov 2014 18:47:28 +0000 (19:47 +0100)]
net: dsa: slave: Fix autoneg for phys on switch MDIO bus
When the ports phys are connected to the switches internal MDIO bus,
we need to connect the phy to the slave netdev, otherwise
auto-negotiation etc, does not work.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ryo Munakata [Wed, 5 Nov 2014 14:45:58 +0000 (23:45 +0900)]
net/9p: remove a comment about pref member which doesn't exist
Signed-off-by: Ryo Munakata <ryomnktml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Wed, 5 Nov 2014 13:03:31 +0000 (18:33 +0530)]
drivers: net: cpsw: remove cpsw_ale_stop from cpsw_ale_destroy
when cpsw is build as modulea and simple insert and removal of module
creates a deadlock, due to delete timer. the timer is created and destroyed
in cpsw_ale_start and cpsw_ale_stop which are from device open and close.
root@am437x-evm:~# modprobe -r ti_cpsw
[ 158.505333] INFO: trying to register non-static key.
[ 158.510623] the code is fine but needs lockdep annotation.
[ 158.516448] turning off the locking correctness validator.
[ 158.522282] CPU: 0 PID: 1339 Comm: modprobe Not tainted
3.14.23-00445-gd41c88f #44
[ 158.530359] [<
c0015380>] (unwind_backtrace) from [<
c0012088>] (show_stack+0x10/0x14)
[ 158.538603] [<
c0012088>] (show_stack) from [<
c054ad70>] (dump_stack+0x78/0x94)
[ 158.546295] [<
c054ad70>] (dump_stack) from [<
c0088008>] (__lock_acquire+0x176c/0x1b74)
[ 158.554711] [<
c0088008>] (__lock_acquire) from [<
c0088944>] (lock_acquire+0x9c/0x104)
[ 158.563043] [<
c0088944>] (lock_acquire) from [<
c004e520>] (del_timer_sync+0x44/0xd8)
[ 158.571289] [<
c004e520>] (del_timer_sync) from [<
bf2eac1c>] (cpsw_ale_destroy+0x10/0x3c [ti_cpsw])
[ 158.580821] [<
bf2eac1c>] (cpsw_ale_destroy [ti_cpsw]) from [<
bf2eb268>] (cpsw_remove+0x30/0xa0 [ti_cpsw])
[ 158.591000] [<
bf2eb268>] (cpsw_remove [ti_cpsw]) from [<
c035ef44>] (platform_drv_remove+0x18/0x1c)
[ 158.600527] [<
c035ef44>] (platform_drv_remove) from [<
c035d8bc>] (__device_release_driver+0x70/0xc8)
[ 158.610236] [<
c035d8bc>] (__device_release_driver) from [<
c035e0d4>] (driver_detach+0xb4/0xb8)
[ 158.619386] [<
c035e0d4>] (driver_detach) from [<
c035d6e4>] (bus_remove_driver+0x4c/0x90)
[ 158.627988] [<
c035d6e4>] (bus_remove_driver) from [<
c00af2a8>] (SyS_delete_module+0x10c/0x198)
[ 158.637144] [<
c00af2a8>] (SyS_delete_module) from [<
c000e580>] (ret_fast_syscall+0x0/0x48)
[ 179.524727] INFO: rcu_sched detected stalls on CPUs/tasks: {} (detected by 0, t=2102 jiffies, g=1487, c=1486, q=6)
[ 179.535741] INFO: Stall ended before state dump start
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karl Beldan [Wed, 5 Nov 2014 14:32:59 +0000 (15:32 +0100)]
net: mv643xx_eth: reclaim TX skbs only when released by the HW
ATM, txq_reclaim will dequeue and free an skb for each tx desc released
by the hw that has TX_LAST_DESC set. However, in case of TSO, each
hw desc embedding the last part of a segment has TX_LAST_DESC set,
losing the one-to-one 'last skb frag'/'TX_LAST_DESC set' correspondance,
which causes data corruption.
Fix this by checking TX_ENABLE_INTERRUPT instead of TX_LAST_DESC, and
warn when trying to dequeue from an empty txq (which can be symptomatic
of releasing skbs prematurely).
Fixes:
3ae8f4e0b98 ('net: mv643xx_eth: Implement software TSO')
Reported-by: Slawomir Gajzner <slawomir.gajzner@gmail.com>
Reported-by: Julien D'Ascenzio <jdascenzio@yahoo.fr>
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory Fong [Tue, 4 Nov 2014 19:21:21 +0000 (11:21 -0800)]
bridge: include in6.h in if_bridge.h for struct in6_addr
if_bridge.h uses struct in6_addr ip6, but wasn't including the in6.h
header. Thomas Backlund originally sent a patch to do this, but this
revealed a redefinition issue: https://lkml.org/lkml/2013/1/13/116
The redefinition issue should have been fixed by the following Linux
commits:
ee262ad827f89e2dc7851ec2986953b5b125c6bc inet: defines IPPROTO_* needed for module alias generation
cfd280c91253cc28e4919e349fa7a813b63e71e8 net: sync some IP headers with glibc
and the following glibc commit:
6c82a2f8d7c8e21e39237225c819f182ae438db3 Coordinate IPv6 definitions for Linux and glibc
so actually include the header now.
Reported-by: Colin Guthrie <colin@mageia.org>
Reported-by: Christiaan Welvaart <cjw@daneel.dyndns.org>
Reported-by: Thomas Backlund <tmb@mageia.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcelo Leitner [Tue, 4 Nov 2014 19:15:08 +0000 (17:15 -0200)]
tcp: zero retrans_stamp if all retrans were acked
Ueki Kohei reported that when we are using NewReno with connections that
have a very low traffic, we may timeout the connection too early if a
second loss occurs after the first one was successfully acked but no
data was transfered later. Below is his description of it:
When SACK is disabled, and a socket suffers multiple separate TCP
retransmissions, that socket's ETIMEDOUT value is calculated from the
time of the *first* retransmission instead of the *latest*
retransmission.
This happens because the tcp_sock's retrans_stamp is set once then never
cleared.
Take the following connection:
Linux remote-machine
| |
send#1---->(*1)|--------> data#1 --------->|
| | |
RTO : :
| | |
---(*2)|----> data#1(retrans) ---->|
| (*3)|<---------- ACK <----------|
| | |
| : :
| : :
| : :
16 minutes (or more) :
| : :
| : :
| : :
| | |
send#2---->(*4)|--------> data#2 --------->|
| | |
RTO : :
| | |
---(*5)|----> data#2(retrans) ---->|
| | |
| | |
RTO*2 : :
| | |
| | |
ETIMEDOUT<----(*6)| |
(*1) One data packet sent.
(*2) Because no ACK packet is received, the packet is retransmitted.
(*3) The ACK packet is received. The transmitted packet is acknowledged.
At this point the first "retransmission event" has passed and been
recovered from. Any future retransmission is a completely new "event".
(*4) After 16 minutes (to correspond with retries2=15), a new data
packet is sent. Note: No data is transmitted between (*3) and (*4).
The socket's timeout SHOULD be calculated from this point in time, but
instead it's calculated from the prior "event" 16 minutes ago.
(*5) Because no ACK packet is received, the packet is retransmitted.
(*6) At the time of the 2nd retransmission, the socket returns
ETIMEDOUT.
Therefore, now we clear retrans_stamp as soon as all data during the
loss window is fully acked.
Reported-by: Ueki Kohei
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 5 Nov 2014 21:23:09 +0000 (16:23 -0500)]
Merge branch 'stmmac-net'
Giuseppe Cavallaro says:
====================
stmmac: review and fix lock and atomicity
Recently some issues have been reported for the driver for locking mechanism
and atomicity.
In fact, enabling DEBUG support to prove lock and to verify if sleeping while
atomic context some warnings occur at runtime. I have reproduced all on STi
platforms.
Concerning the tx path, I had provided a patch time ago but
I discarded the idea to completely remove locks; in this patch-set we can have
some useful fixes instead of.
This patch-set is to fix the atomicity in the PM stuff where I tried to collect
all the points and advice reported in the past weeks.
As final result, on my side no warnings and no problem when suspend/resume the
driver on STi boxes.
I also added a patch that fixes the locks for the EEE.
As pointed in some thread there was a design problem behind the eee
initialization and I have tried to fix that before.
As final result no issues when proving locks too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Giuseppe CAVALLARO [Tue, 4 Nov 2014 16:08:09 +0000 (17:08 +0100)]
stmmac: fix atomicity in pm routines
This patch is to fix the atomicity when suspend and resume the
driver. The clk api have been changed (as reported by Hao Liang)
and the skb allocation is done out of the hw setup function and
taking care about the GFP flags.
Reported-by: Hao Liang <hliang1025@gmail.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Hao Liang <hliang1025@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Giuseppe CAVALLARO [Tue, 4 Nov 2014 16:08:08 +0000 (17:08 +0100)]
stmmac: fix concurrency in eee initialization.
This patch aims to fix the concurrency in eee initialization
inside the stmmac driver and related warnings when enable
DEBUG_ATOMIC_SLEEP.
Prior this patch, the stmmac_eee_init could be called in several places
as shown below:
stmmac_open stmmac_resume PHY Layer
| | |
stmmac_hw_setup stmmac_adjust_link
| | stmmac ethtool
|__________________________|______________|
|
stmmac_eee_init
The patch removes the stmmac_eee_init call inside the stmmac_hw_setup
that is unnecessary. It is sufficient to call it in the adjust_link to
always guarantee that EEE is always configured at mac level too.
Fixing the lock protection now it is covered another case (not
considered before). The stmmac_eee_init could be called by the ethtool
so critical sections must be protected inside this function too.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Giuseppe CAVALLARO [Tue, 4 Nov 2014 16:08:07 +0000 (17:08 +0100)]
stmmac: fix lock in stmmac_set_rx_mode
When compile with CONFIG_PROVE_LOCKING the following warnings happen:
[snip]
HARDIRQ-ON-W at:
[<
c0480c1c>] _raw_spin_lock+0x3c/0x4c
[<
c02c2828>] stmmac_set_rx_mode+0x18/0x3c
[<
c038b2cc>] dev_set_rx_mode+0x1c/0x28
[<
c038b38c>] __dev_open+0xb4/0xf8
[<
c038b5a8>] __dev_change_flags+0x94/0x128
[<
c038b6a8>] dev_change_flags+0x10/0x48
[<
c062afe0>] ip_auto_config+0x1d4/0x1084
[<
c000873c>] do_one_initcall+0x108/0x15c
[<
c060ec50>] kernel_init_freeable+0x1a8/0x248
[<
c0472cc0>] kernel_init+0x8/0x160
[<
c000dfc8>] ret_from_fork+0x14/0x2c
INITIAL USE at:
[<
c0480c1c>] _raw_spin_lock+0x3c/0x4c
[<
c02c2828>] stmmac_set_rx_mode+0x18/0x3c
[<
c038b2cc>] dev_set_rx_mode+0x1c/0x28
[<
c038b38c>] __dev_open+0xb4/0xf8
[<
c038b5a8>] __dev_change_flags+0x94/0x128
[<
c038b6a8>] dev_change_flags+0x10/0x48
[<
c062afe0>] ip_auto_config+0x1d4/0x1084
[<
c000873c>] do_one_initcall+0x108/0x15c
[<
c060ec50>] kernel_init_freeable+0x1a8/0x248
[<
c0472cc0>] kernel_init+0x8/0x160
[<
c000dfc8>] ret_from_fork+0x14/0x2c
so the patch just removes the lock protection in the stmmac_set_rx_mode
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Emilio Lopez <emilio@elopez.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fabrice Gasnier [Tue, 4 Nov 2014 16:08:06 +0000 (17:08 +0100)]
stmmac: release tx lock, in case of dma mapping error.
Add missing spin_unlock when tx frames gets dropped.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fabrice Gasnier [Tue, 4 Nov 2014 16:08:05 +0000 (17:08 +0100)]
stmmac: fix stmmac_tx_avail should be called with TX locked
stmmac_tx_avail() may lie if used unprotected. It's using cur_tx
and dirty_tx index. These index may be already in use by tx_clean
when entering xmit routine. So, this should be called locked.
This can cause transmit queue to be stuck, with following message:
NETDEV WATCHDOG: eth0 (stmmaceth): transmit queue 0 timed out
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chen Gang [Tue, 4 Nov 2014 14:43:17 +0000 (22:43 +0800)]
drivers: net: ethernet: xilinx: xilinx_emaclite: revert the original commit "
1db3ddff1602edf2390b7667dcbaa0f71512e3ea"
Microblaze is a fpga soft core, it can be customized easily, which may
cause many various hardware version strings.
So the original fix patch based on hard-coded compatible version strings
is not a good idea (although it is correct for current issue). For it,
there will be a new solving way soon (which based on the device tree).
The original issue is related with qemu, so can only change the hardware
version string in qemu for it, then keep the original driver no touch (
qemu is for virtualization which has much easier life than real world).
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rasmus Villemoes [Wed, 5 Nov 2014 20:44:27 +0000 (21:44 +0100)]
include/linux/socket.h: Fix comment
File descriptors are always closed on exit :-)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loganaden Velvindron [Tue, 4 Nov 2014 11:02:49 +0000 (03:02 -0800)]
net: Add missing descriptions for fwmark_reflect for ipv4 and ipv6.
It was initially sent by Lorenzo Colitti, but was subsequently
lost in the final diff he submitted.
Signed-off-by: Loganaden Velvindron <logan@elandsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross [Tue, 4 Nov 2014 03:38:38 +0000 (19:38 -0800)]
geneve: Unregister pernet subsys on module unload.
The pernet ops aren't ever unregistered, which causes a memory
leak and an OOPs if the module is ever reinserted.
Fixes:
0b5e8b8eeae4 ("net: Add Geneve tunneling protocol driver")
CC: Andy Zhou <azhou@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross [Tue, 4 Nov 2014 03:38:37 +0000 (19:38 -0800)]
geneve: Set GSO type on transmit.
Geneve does not currently set the inner protocol type when
transmitting packets. This causes GSO segmentation to fail on NICs
that do not support Geneve offloading.
CC: Andy Zhou <azhou@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 4 Nov 2014 22:08:47 +0000 (17:08 -0500)]
Merge branch 'xgene-net'
Iyappan Subramanian says:
====================
drivers: net: xgene: Fix crash for backward compatibility
This patch set fixes the following issues that were reported during regression.
Patch 1,2 : Adds backward compatibility with the older firmware (<= 1.13.28).
Patch 3 : Use separate hardware resources (descriptor ring, prefetch buffer)
that are not shared with the firmware
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Iyappan Subramanian [Mon, 3 Nov 2014 19:59:56 +0000 (11:59 -0800)]
drivers: net: xgene: fix: Use separate resources
This patch fixes the following kernel crash during SGMII based 1GbE probe.
BUG: Bad page state in process swapper/0 pfn:
40fe6ad
page:
ffffffbee37a75d8 count:-1 mapcount:0 mapping: (null) index:0x0
flags: 0x0()
page dumped because: nonzero _count
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.17.0+ #7
Call trace:
[<
ffffffc000087fa0>] dump_backtrace+0x0/0x12c
[<
ffffffc0000880dc>] show_stack+0x10/0x1c
[<
ffffffc0004d981c>] dump_stack+0x74/0xc4
[<
ffffffc00012fe70>] bad_page+0xd8/0x128
[<
ffffffc000133000>] get_page_from_freelist+0x4b8/0x640
[<
ffffffc000133260>] __alloc_pages_nodemask+0xd8/0x834
[<
ffffffc0004194f8>] __netdev_alloc_frag+0x124/0x1b8
[<
ffffffc00041bfdc>] __netdev_alloc_skb+0x90/0x10c
[<
ffffffc00039ff30>] xgene_enet_refill_bufpool+0x11c/0x280
[<
ffffffc0003a11a4>] xgene_enet_process_ring+0x168/0x340
[<
ffffffc0003a1498>] xgene_enet_napi+0x1c/0x50
[<
ffffffc00042b454>] net_rx_action+0xc8/0x18c
[<
ffffffc0000b0880>] __do_softirq+0x114/0x24c
[<
ffffffc0000b0c34>] irq_exit+0x94/0xc8
[<
ffffffc0000e68a0>] __handle_domain_irq+0x8c/0xf4
[<
ffffffc000081288>] gic_handle_irq+0x30/0x7c
This was due to hardware resource sharing conflict with the firmware. This
patch fixes this crash by using resources (descriptor ring, prefetch buffer)
that are not shared.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Iyappan Subramanian [Mon, 3 Nov 2014 19:59:55 +0000 (11:59 -0800)]
drivers: net: xgene: Backward compatibility with older firmware
This patch adds support when used with older firmware (<= 1.13.28).
- Added xgene_ring_mgr_init() to check whether ring manager is initialized
- Calling xgene_ring_mgr_init() from xgene_port_ops.reset()
- To handle errors, changed the return type of xgene_port_ops.reset()
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Iyappan Subramanian [Mon, 3 Nov 2014 19:59:54 +0000 (11:59 -0800)]
dtb: xgene: fix: Backward compatibility with older firmware
The following kernel crash was reported when using older firmware (<= 1.13.28).
[ 0.980000] libphy: APM X-Gene MDIO bus: probed
[ 1.130000] Unhandled fault: synchronous external abort (0x96000010) at 0xffffff800009a17c
[ 1.140000] Internal error: :
96000010 [#1] SMP
[ 1.140000] Modules linked in:
[ 1.140000] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.17.0+ #21
[ 1.140000] task:
ffffffc3f0110000 ti:
ffffffc3f0064000 task.ti:
ffffffc3f0064000
[ 1.140000] PC is at ioread32+0x58/0x68
[ 1.140000] LR is at xgene_enet_setup_ring+0x18c/0x1cc
[ 1.140000] pc : [<
ffffffc0003cec68>] lr : [<
ffffffc00053dad8>] pstate:
a0000045
[ 1.140000] sp :
ffffffc3f0067b20
[ 1.140000] x29:
ffffffc3f0067b20 x28:
ffffffc000aa8ea0
[ 1.140000] x27:
ffffffc000bb2000 x26:
ffffffc000a64270
[ 1.140000] x25:
ffffffc000b05ad8 x24:
ffffffc0ff99ba58
[ 1.140000] x23:
0000000000004000 x22:
0000000000004000
[ 1.140000] x21:
0000000000000200 x20:
0000000000200000
[ 1.140000] x19:
ffffffc0ff99ba18 x18:
ffffffc0007a6000
[ 1.140000] x17:
0000000000000007 x16:
000000000000000e
[ 1.140000] x15:
0000000000000001 x14:
0000000000000000
[ 1.140000] x13:
ffffffbeedb71320 x12:
00000000ffffff80
[ 1.140000] x11:
0000000000000002 x10:
0000000000000000
[ 1.140000] x9 :
0000000000000000 x8 :
ffffffc3eb2a4000
[ 1.140000] x7 :
0000000000000000 x6 :
0000000000000000
[ 1.140000] x5 :
0000000001080000 x4 :
000000007d654010
[ 1.140000] x3 :
ffffffffffffffff x2 :
000000000003ffff
[ 1.140000] x1 :
ffffff800009a17c x0 :
ffffff800009a17c
The issue was that the older firmware does not support 10GbE and
SGMII based 1GBE interfaces.
This patch changes the address length of the reg property of sgmii0 and xgmii
nodes and serves as preparatory patch for the fix.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Reported-by: Dann Frazier <dann.frazier@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville [Tue, 4 Nov 2014 20:54:46 +0000 (15:54 -0500)]
Merge tag 'mac80211-for-john-2014-11-04' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg <johannes@sipsolutions.net> says:
"This contains another small set of fixes for 3.18, these are all
over the place and most of the bugs are old, one even dates back
to the original mac80211 we merged into the kernel."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 4 Nov 2014 20:46:15 +0000 (15:46 -0500)]
Merge tag 'iwlwifi-for-john-2014-11-03' of git://git./linux/kernel/git/iwlwifi/iwlwifi-fixes
Emmanuel Grumbach <egrumbach@gmail.com> says:
"I fix here two issues that are related to the firmware
loading flow. A user reported that he couldn't load the
driver because the rfkill line was pulled up while we
were running the calibrations. This was happening while
booting the system: systemd was restoring the "disable
wifi settings" and that raised an RFKILL interrupt during
the calibration. Our driver didn't handle that properly
and this is now fixed."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Edward Cree [Mon, 3 Nov 2014 14:14:35 +0000 (14:14 +0000)]
sfc: don't BUG_ON efx->max_channels == 0 in probe
efx_ef10_probe() was BUGging out if the BAR2 size was 0. This is
unnecessarily violent; instead we should just fail to probe the device.
Kept a WARN_ON as this problem indicates a broken or misconfigured NIC.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 3 Nov 2014 20:42:35 +0000 (15:42 -0500)]
Merge branch 'ipv6_tunnel_iflink_init'
Steffen Klassert says:
====================
ipv6: Fix iflink setting for ipv6 tunnels
The ipv6 tunnels do the dev->iflink setting too early, it gets
overwritten by register_netdev(). So set dev->iflink from within
a ndo_init function to keep the configured setting.
This patchset fixes this for ip6_tunnel, vti6, sit and gre6.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert [Mon, 3 Nov 2014 08:19:30 +0000 (09:19 +0100)]
gre6: Move the setting of dev->iflink into the ndo_init functions.
Otherwise it gets overwritten by register_netdev().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert [Mon, 3 Nov 2014 08:19:29 +0000 (09:19 +0100)]
sit: Use ipip6_tunnel_init as the ndo_init function.
ipip6_tunnel_init() sets the dev->iflink via a call to
ipip6_tunnel_bind_dev(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for ipv6 tunnels. Fix this by using ipip6_tunnel_init() as the
ndo_init function. Then ipip6_tunnel_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert [Mon, 3 Nov 2014 08:19:28 +0000 (09:19 +0100)]
vti6: Use vti6_dev_init as the ndo_init function.
vti6_dev_init() sets the dev->iflink via a call to
vti6_link_config(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for vti6 tunnels. Fix this by using vti6_dev_init() as the
ndo_init function. Then vti6_dev_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert [Mon, 3 Nov 2014 08:19:27 +0000 (09:19 +0100)]
ip6_tunnel: Use ip6_tnl_dev_init as the ndo_init function.
ip6_tnl_dev_init() sets the dev->iflink via a call to
ip6_tnl_link_config(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for ipv6 tunnels. Fix this by using ip6_tnl_dev_init() as the
ndo_init function. Then ip6_tnl_dev_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 3 Nov 2014 06:01:25 +0000 (14:01 +0800)]
macvtap: Fix csum_start when VLAN tags are present
When VLAN is in use in macvtap_put_user, we end up setting
csum_start to the wrong place. The result is that the whoever
ends up doing the checksum setting will corrupt the packet instead
of writing the checksum to the expected location, usually this
means writing the checksum with an offset of -4.
This patch fixes this by adjusting csum_start when VLAN tags are
detected.
Fixes:
f09e2249c4f5 ("macvtap: restore vlan header on user read")
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Signed-off-by: David S. Miller <davem@davemloft.net>
Nimrod Andy [Mon, 3 Nov 2014 05:26:50 +0000 (13:26 +0800)]
net: fec: fix suspend broken on multiple MACs sillicons
On i.MX6SX sdb platform, there has two same enet MACs, after system up,
just eth0 is up, and then do suspend/resume test:
[ 50.437967] PM: Syncing filesystems ... done.
[ 50.476924] Freezing user space processes ... (elapsed 0.005 seconds) done.
[ 50.490093] Freezing remaining freezable tasks ... (elapsed 0.004 seconds) done.
[ 50.559771] ------------[ cut here ]------------
[ 50.564453] WARNING: CPU: 0 PID: 575 at drivers/clk/clk.c:851 __clk_disable+0x60/0x6c()
[ 50.572475] Modules linked in:
[ 50.575578] CPU: 0 PID: 575 Comm: sh Not tainted
3.18.0-rc2-next-20141031-00007-gf61135b #21
[ 50.584031] Backtrace:
[ 50.586550] [<
80011ecc>] (dump_backtrace) from [<
8001206c>] (show_stack+0x18/0x1c)
[ 50.594136] r6:
808a7a54 r5:
00000000 r4:
00000000 r3:
00000000
[ 50.599920] [<
80012054>] (show_stack) from [<
806ab3c0>] (dump_stack+0x80/0x9c)
[ 50.607187] [<
806ab340>] (dump_stack) from [<
8002a3e8>] (warn_slowpath_common+0x6c/0x8c)
[ 50.615294] r5:
00000353 r4:
00000000
[ 50.618940] [<
8002a37c>] (warn_slowpath_common) from [<
8002a42c>] (warn_slowpath_null+0x24/0x2c)
[ 50.627738] r8:
00000000 r7:
be144c44 r6:
be015600 r5:
80070013 r4:
be015600
[ 50.634573] [<
8002a408>] (warn_slowpath_null) from [<
804f8d4c>] (__clk_disable+0x60/0x6c)
[ 50.642777] [<
804f8cec>] (__clk_disable) from [<
804f8e5c>] (clk_disable+0x2c/0x38)
[ 50.650359] r4:
be015600 r3:
00000000
[ 50.654006] [<
804f8e30>] (clk_disable) from [<
80420ab4>] (fec_enet_clk_enable+0xc4/0x258)
[ 50.662196] r5:
be3cb620 r4:
be3cb000
[ 50.665838] [<
804209f0>] (fec_enet_clk_enable) from [<
80421178>] (fec_suspend+0x30/0x180)
[ 50.674026] r7:
be144c44 r6:
be144c10 r5:
8037f5a4 r4:
be3cb000
[ 50.679802] [<
80421148>] (fec_suspend) from [<
8037f5d8>] (platform_pm_suspend+0x34/0x64)
[ 50.687906] r10:
00000000 r9:
00000000 r8:
00000000 r7:
be144c44 r6:
be144c10 r5:
8037f5a4
[ 50.695852] r4:
be144c10 r3:
80421148
[ 50.699511] [<
8037f5a4>] (platform_pm_suspend) from [<
8038784c>] (dpm_run_callback.isra.14+0x34/0x6c)
[ 50.708764] [<
80387818>] (dpm_run_callback.isra.14) from [<
80387f00>] (__device_suspend+0x12c/0x2a4)
[ 50.717909] r9:
8098ec8c r8:
80973bec r6:
00000002 r5:
811c7038 r4:
be144c10
[ 50.724746] [<
80387dd4>] (__device_suspend) from [<
803894fc>] (dpm_suspend+0x64/0x224)
[ 50.732675] r8:
80973bec r7:
be144c10 r6:
8098ec24 r5:
811c7038 r4:
be144cc4
[ 50.739509] [<
80389498>] (dpm_suspend) from [<
8038999c>] (dpm_suspend_start+0x60/0x68)
[ 50.747438] r10:
8082fa24 r9:
00000000 r8:
00000004 r7:
00000003 r6:
00000000 r5:
8116ec80
[ 50.755386] r4:
00000002
[ 50.757969] [<
8038993c>] (dpm_suspend_start) from [<
800679d8>] (suspend_devices_and_enter+0x90/0x3ec)
[ 50.767202] r4:
00000003 r3:
8116eca0
[ 50.770843] [<
80067948>] (suspend_devices_and_enter) from [<
80067f40>] (pm_suspend+0x20c/0x2a4)
[ 50.779553] r8:
00000004 r7:
00000003 r6:
00000000 r5:
8116ec8c r4:
00000003
[ 50.786394] [<
80067d34>] (pm_suspend) from [<
80066858>] (state_store+0x70/0xc0)
[ 50.793718] r6:
8116ec90 r5:
00000003 r4:
bd88a800 r3:
0000006d
[ 50.799496] [<
800667e8>] (state_store) from [<
802b0384>] (kobj_attr_store+0x1c/0x28)
[ 50.807251] r10:
bd399f78 r8:
00000000 r7:
bd88a800 r6:
bd88a800 r5:
00000004 r4:
bd085680
[ 50.815219] [<
802b0368>] (kobj_attr_store) from [<
80153090>] (sysfs_kf_write+0x54/0x58)
[ 50.823252] [<
8015303c>] (sysfs_kf_write) from [<
80151fd8>] (kernfs_fop_write+0xd0/0x194)
[ 50.831441] r6:
00000004 r5:
bd08568c r4:
bd085680 r3:
8015303c
[ 50.837220] [<
80151f08>] (kernfs_fop_write) from [<
800eddb4>] (vfs_write+0xb8/0x1a8)
[ 50.844975] r10:
00000000 r9:
00000000 r8:
00000000 r7:
bd399f78 r6:
01336408 r5:
00000004
[ 50.852924] r4:
bc584dc0
[ 50.855505] [<
800edcfc>] (vfs_write) from [<
800ee0b8>] (SyS_write+0x48/0x88)
[ 50.862567] r10:
00000000 r8:
00000000 r7:
01336408 r6:
00000004 r5:
bc584dc0 r4:
bc584dc0
[ 50.870537] [<
800ee070>] (SyS_write) from [<
8000eb00>] (ret_fast_syscall+0x0/0x48)
[ 50.878120] r9:
bd398000 r8:
8000ecc4 r7:
00000004 r6:
76f42b48 r5:
01336408 r4:
00000004
[ 50.885983] ---[ end trace
7545115d752a316a ]---
[ 50.890765] ------------[ cut here ]------------
The root cause is that eth1 is not opened and clock is not enabled, and .suspend() still
call .fec_enet_clk_enable() to disable clock.
To avoid the broken, let it check network device up status by calling .netif_running()
before disable/enable clocks.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 3 Nov 2014 19:27:12 +0000 (14:27 -0500)]
Merge branch 'tun-net'
Herbert Xu says:
====================
tun: Fix csum_start and TUN_PKT_STRIP
The first patch fixes a serious problem that breaks checksum offload
in VMs while the second patch fixes a problem that probably affects
no one.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sun, 2 Nov 2014 20:30:14 +0000 (04:30 +0800)]
tun: Fix TUN_PKT_STRIP setting
We set the flag TUN_PKT_STRIP if the user buffer provided is too
small to contain the entire packet plus meta-data. However, this
has been broken ever since we added GSO meta-data. VLAN acceleration
also has the same problem.
This patch fixes this by taking both into account when setting the
TUN_PKT_STRIP flag.
The fact that this has been broken for six years without anyone
realising means that nobody actually uses this flag.
Fixes:
f43798c27684 ("tun: Allow GSO using virtio_net_hdr")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sun, 2 Nov 2014 20:30:13 +0000 (04:30 +0800)]
tun: Fix csum_start with VLAN acceleration
When VLAN acceleration is in use on the xmit path, we end up
setting csum_start to the wrong place. The result is that the
whoever ends up doing the checksum setting will corrupt the packet
instead of writing the checksum to the expected location, usually
this means writing the checksum with an offset of -4.
This patch fixes this by adjusting csum_start when VLAN acceleration
is detected.
Fixes:
6680ec68eff4 ("tuntap: hardware vlan tx support")
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Sun, 2 Nov 2014 19:31:41 +0000 (11:31 -0800)]
uapi: add missing network related headers to kbuild
The makefile for sanitizing kernel headers uses the kbuild file
to determine which files to do. Several networking related headers
were missing. Without these headers iproute2 build would break.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Mon, 3 Nov 2014 02:19:15 +0000 (18:19 -0800)]
netfilter: nft_reject_bridge: Fix powerpc build error
Fix:
net/bridge/netfilter/nft_reject_bridge.c:
In function 'nft_reject_br_send_v6_unreach':
net/bridge/netfilter/nft_reject_bridge.c:240:3:
error: implicit declaration of function 'csum_ipv6_magic'
csum_ipv6_magic(&nip6h->saddr, &nip6h->daddr,
^
make[3]: *** [net/bridge/netfilter/nft_reject_bridge.o] Error 1
Seen with powerpc:allmodconfig.
Fixes:
523b929d5446 ("netfilter: nft_reject_bridge: don't use IP stack to reject traffic")
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emmanuel Grumbach [Sun, 2 Nov 2014 13:48:09 +0000 (15:48 +0200)]
iwlwifi: fix RFkill while calibrating
If the RFkill interrupt fires while we calibrate, it would
make the firmware fail and the driver wasn't able to recover.
Change the flow so that the driver will kill the firmware
in that case.
Since we have now two flows that are calling
trans_stop_device (the RFkill interrupt and the
op_mode_mvm_start function) - we need to better sync this.
Use the STATUS_DEVICE_ENABLED in the pcie transport in an
atomic way to achieve this.
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=86231
CC: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Johannes Berg [Mon, 3 Nov 2014 12:57:46 +0000 (13:57 +0100)]
mac80211: fix use-after-free in defragmentation
Upon receiving the last fragment, all but the first fragment
are freed, but the multicast check for statistics at the end
of the function refers to the current skb (the last fragment)
causing a use-after-free bug.
Since multicast frames cannot be fragmented and we check for
this early in the function, just modify that check to also
do the accounting to fix the issue.
Cc: stable@vger.kernel.org
Reported-by: Yosef Khyal <yosefx.khyal@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Linus Walleij [Fri, 31 Oct 2014 20:32:06 +0000 (21:32 +0100)]
smc91x: retrieve IRQ and trigger flags in a modern way
The SMC91x is written to explicitly look up the IRQ resource
from the platform device and extract the IRQ and flags, however
the platform_get_irq() does additional things, like call
of_irq_get() in the device tree case, which will translate
the IRQ using the irqdomain and defer the probe if the
IRQ host cannot be found.
As we're not looking up the resource, this will not retrieve
the IRQ flags, but that is better done using
irqd_get_trigger_type(), as the trigger is what the driver
wants to modify. We take care to preserve the semantics that
will make the trigger type provided from the resource
override any local specifier.
Tested on the Nomadik NHK15 which has its SMC91x IRQ line
connected to a STMPE2401 GPIO expander on I2C.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chen Gang [Sat, 1 Nov 2014 03:08:08 +0000 (11:08 +0800)]
drivers: net: ethernet: xilinx: xilinx_emaclite: Compatible with 'xlnx, xps-ethernetlite-2.00.b' for QEMU using
When use current latest upstream qemu (current version: 2.1.2), need let
driver compatible with 'xlnx,xps-ethernetlite-2.00.b', or can not find
net device in microblaze qemu. Related QEMU commands under fedora 20:
yum install libvirt
yum install tunctl
tunctl -b
ip link set tap0 up
brctl addif virbr0 tap0
./microblaze-softmmu/qemu-system-microblaze -M petalogix-s3adsp1800 \
-kernel ../linux-stable.microblaze/arch/microblaze/boot/linux.bin \
-no-reboot -append "console=ttyUL0,115200 doreboot" -nographic \
-net nic,vlan=0,model=xlnx.xps-ethernetlite,macaddr=00:16:35:AF:94:00 \
-net tap,vlan=0,ifname=tap0,script=no,downscript=no
in microblaze qemu bash (guest machine):
ifconfig eth0 add 192.168.122.2 netmask 255.255.255.0
ifconfig eth0 up
After add this patch, can find the device, and can be used by 'telnetd'
(need cross-build busybox with glibc for it), then outside can telnet to
it without password.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 1 Nov 2014 19:14:07 +0000 (15:14 -0400)]
Merge branch 'systemport-net'
Florian Fainelli says:
====================
net: systemport: TX dma fixes
This patch series contains two fixes for our transmit path, first one
is a pretty nasty one since we were not allocating a large enough
dma coherent pool for our transmit descriptors, which would work most of the
time, since allocations are contiguous and we could have.
Second patch fixes a less frequent, though highly likley crash when using
CMA allocations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 31 Oct 2014 22:51:35 +0000 (15:51 -0700)]
net: systemport: do not crash freeing an unitialized TX ring
Callers of bcm_sysport_init_tx_ring() can currently fail, and will
always call bcm_sysport_fini_tx_ring() in a loop ending at the number of
TX queues (32) without checking if the TX ring was successfully
initialized or not.
Update bcm_sysport_fini_tx_ring() to return early and avoid a crash
de-referencing ring->cbs if the TX ring was not initialized, since
ring->cbs is the last part of the initialization done by
bcm_sysport_init_tx_ring() that could fail.
Fixes:
80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 31 Oct 2014 22:51:34 +0000 (15:51 -0700)]
net: systemport: fix DMA allocation/freeing sizes
We should not be allocating a single byte of DMA coherent memory, but
instead a full-sized struct dma_desc (8 bytes).
Fixes:
80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudip Mukherjee [Sat, 1 Nov 2014 11:29:34 +0000 (16:59 +0530)]
net: mvpp2: fix possible memory leak
we are allocating memory using kzalloc for struct mvpp2_prs_entry,
but later when we are getting error we were just returning the error
value without releasing the memory.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 31 Oct 2014 17:43:06 +0000 (13:43 -0400)]
sunhme: Add DMA mapping error checks.
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 1 Nov 2014 02:51:11 +0000 (19:51 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"A bunch of fixes for minor defects reported by Coverity, a few driver
fixups and revert of i8042.nomux change so that we are once again
enable active MUX mode if box claims to support it"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: i8042 - disable active multiplexing by default"
Input: altera_ps2 - use correct type for irq return value
Input: altera_ps2 - write to correct register when disabling interrupts
Input: max77693-haptic - fix potential overflow
Input: psmouse - remove unneeded check in psmouse_reconnect()
Input: vsxxxaa - fix code dropping bytes from queue
Input: ims-pcu - fix dead code in ims_pcu_ofn_reg_addr_store()
Input: opencores-kbd - fix error handling
Input: wm97xx - adapt parameters to tosa touchscreen.
Input: i8042 - quirks for Fujitsu Lifebook A544 and Lifebook AH544
Input: stmpe-keypad - fix valid key line bitmask
Input: soc_button_array - update calls to gpiod_get*()
Linus Torvalds [Sat, 1 Nov 2014 02:08:25 +0000 (19:08 -0700)]
Merge tag 'pm+acpi-3.18-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are fixes received after my previous pull request plus one that
has been in the works for quite a while, but its previous version
caused problems to happen, so it's been deferred till now.
Fixed are two recent regressions (MFD enumeration and cpufreq-dt),
ACPI EC regression introduced in 3.17, system suspend error code path
regression introduced in 3.15, an older bug related to recovery from
failing resume from hibernation and a cpufreq-dt driver issue related
to operation performance points.
Specifics:
- Fix a crash on r8a7791/koelsch during resume from system suspend
caused by a recent cpufreq-dt commit (Geert Uytterhoeven).
- Fix an MFD enumeration problem introduced by a recent commit adding
ACPI support to the MFD subsystem that exposed a weakness in the
ACPI core causing ACPI enumeration to be applied to all devices
associated with one ACPI companion object, although it should be
used for one of them only (Mika Westerberg).
- Fix an ACPI EC regression introduced during the 3.17 cycle causing
some Samsung laptops to misbehave as a result of a workaround
targeted at some Acer machines. That includes a revert of a commit
that went too far and a quirk for the Acer machines in question.
From Lv Zheng.
- Fix a regression in the system suspend error code path introduced
during the 3.15 cycle that causes it to fail to take errors from
asychronous execution of "late" suspend callbacks into account
(Imre Deak).
- Fix a long-standing bug in the hibernation resume error code path
that fails to roll back everything correcty on "freeze" callback
errors and leaves some devices in a "suspended" state causing more
breakage to happen subsequently (Imre Deak).
- Make the cpufreq-dt driver disable operation performance points
that are not supported by the VR connected to the CPU voltage plane
with acceptable tolerance instead of constantly failing voltage
scaling later on (Lucas Stach)"
* tag 'pm+acpi-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer.
Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC"
cpufreq: cpufreq-dt: Restore default cpumask_setall(policy->cpus)
PM / Sleep: fix recovery during resuming from hibernation
PM / Sleep: fix async suspend_late/freeze_late error handling
ACPI: Use ACPI companion to match only the first physical device
cpufreq: cpufreq-dt: disable unsupported OPPs
Linus Torvalds [Sat, 1 Nov 2014 01:48:29 +0000 (18:48 -0700)]
Merge tag 'pci-v3.18-fixes-1' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These changes, intended for v3.18, fix:
Sysfs
- Fix "enable" filename change (Greg Kroah-Hartman)
An unintentional sysfs filename change in commit
5136b2da770d
("PCI: convert bus code to use dev_groups"), which appeared in
v3.13, changed "enable" to "enabled", and this changes it back.
Old users of "enable" are currently broken and will be helped by
this change. Anything that started to use "enabled" after v3.13
will be broken by this change. If necessary, we can add a symlink
to make both work, but this patch doesn't do that.
PCI device hotplug
- Revert duplicate merge (Kamal Mostafa)
A mistaken duplicate merge that added a check twice. Nothing's
broken; this just removes the unnecessary code.
Freescale i.MX6
- Wait for clocks to stabilize after ref_en (Richard Zhu)
An i.MX6 clock problem that prevents mx6 nitrogen boards from booting"
* tag 'pci-v3.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Rename sysfs 'enabled' file back to 'enable'
PCI: imx6: Wait for clocks to stabilize after ref_en
Revert duplicate "PCI: pciehp: Prevent NULL dereference during probe"
Andy Lutomirski [Sat, 1 Nov 2014 01:08:45 +0000 (18:08 -0700)]
x86_64, entry: Fix out of bounds read on sysenter
Rusty noticed a Really Bad Bug (tm) in my NT fix. The entry code
reads out of bounds, causing the NT fix to be unreliable. But, and
this is much, much worse, if your stack is somehow just below the
top of the direct map (or a hole), you read out of bounds and crash.
Excerpt from the crash:
[ 1.129513] RSP: 0018:
ffff88001da4bf88 EFLAGS:
00010296
2b:* f7 84 24 90 00 00 00 testl $0x4000,0x90(%rsp)
That read is deterministically above the top of the stack. I
thought I even single-stepped through this code when I wrote it to
check the offset, but I clearly screwed it up.
Fixes:
8c7aa698baca ("x86_64, entry: Filter RFLAGS.NT on entry from userspace")
Reported-by: Rusty Russell <rusty@ozlabs.org>
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 31 Oct 2014 23:22:29 +0000 (16:22 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"A set of miscellaneous ext4 bug fixes for 3.18"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: make ext4_ext_convert_to_initialized() return proper number of blocks
ext4: bail early when clearing inode journal flag fails
ext4: bail out from make_indexed_dir() on first error
jbd2: use a better hash function for the revoke table
ext4: prevent bugon on race between write/fcntl
ext4: remove extent status procfs files if journal load fails
ext4: disallow changing journal_csum option during remount
ext4: enable journal checksum when metadata checksum feature enabled
ext4: fix oops when loading block bitmap failed
ext4: fix overflow when updating superblock backups after resize
Linus Torvalds [Fri, 31 Oct 2014 23:18:47 +0000 (16:18 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs
Pull quota and ext3 fixes from Jan Kara.
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fs, jbd: use a more generic hash function
quota: Properly return errors from dquot_writeback_dquots()
ext3: Don't check quota format when there are no quota files
Linus Torvalds [Fri, 31 Oct 2014 22:04:58 +0000 (15:04 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"A bit has accumulated, but it's been a week or so since my last batch
of post-merge-window fixes, so...
1) Missing module license in netfilter reject module, from Pablo.
Lots of people ran into this.
2) Off by one in mac80211 baserate calculation, from Karl Beldan.
3) Fix incorrect return value from ax88179_178a driver's set_mac_addr
op, which broke use of it with bonding. From Ian Morgan.
4) Checking of skb_gso_segment()'s return value was not all
encompassing, it can return an SKB pointer, a pointer error, or
NULL. Fix from Florian Westphal.
This is crummy, and longer term will be fixed to just return error
pointers or a real SKB.
6) Encapsulation offloads not being handled by
skb_gso_transport_seglen(). From Florian Westphal.
7) Fix deadlock in TIPC stack, from Ying Xue.
8) Fix performance regression from using rhashtable for netlink
sockets. The problem was the synchronize_net() invoked for every
socket destroy. From Thomas Graf.
9) Fix bug in eBPF verifier, and remove the strong dependency of BPF
on NET. From Alexei Starovoitov.
10) In qdisc_create(), use the correct interface to allocate
->cpu_bstats, otherwise the u64_stats_sync member isn't
initialized properly. From Sabrina Dubroca.
11) Off by one in ip_set_nfnl_get_byindex(), from Dan Carpenter.
12) nf_tables_newchain() was erroneously expecting error pointers from
netdev_alloc_pcpu_stats(). It only returna a valid pointer or
NULL. From Sabrina Dubroca.
13) Fix use-after-free in _decode_session6(), from Li RongQing.
14) When we set the TX flow hash on a socket, we mistakenly do so
before we've nailed down the final source port. Move the setting
deeper to fix this. From Sathya Perla.
15) NAPI budget accounting in amd-xgbe driver was counting descriptors
instead of full packets, fix from Thomas Lendacky.
16) Fix total_data_buflen calculation in hyperv driver, from Haiyang
Zhang.
17) Fix bcma driver build with OF_ADDRESS disabled, from Hauke
Mehrtens.
18) Fix mis-use of per-cpu memory in TCP md5 code. The problem is
that something that ends up being vmalloc memory can't be passed
to the crypto hash routines via scatter-gather lists. From Eric
Dumazet.
19) Fix regression in promiscuous mode enabling in cdc-ether, from
Olivier Blin.
20) Bucket eviction and frag entry killing can race with eachother,
causing an unlink of the object from the wrong list. Fix from
Nikolay Aleksandrov.
21) Missing initialization of spinlock in cxgb4 driver, from Anish
Bhatt.
22) Do not cache ipv4 routing failures, otherwise if the sysctl for
forwarding is subsequently enabled this won't be seen. From
Nicolas Cavallari"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (131 commits)
drivers: net: cpsw: Support ALLMULTI and fix IFF_PROMISC in switch mode
drivers: net: cpsw: Fix broken loop condition in switch mode
net: ethtool: Return -EOPNOTSUPP if user space tries to read EEPROM with lengh 0
stmmac: pci: set default of the filter bins
net: smc91x: Fix gpios for device tree based booting
mpls: Allow mpls_gso to be built as module
mpls: Fix mpls_gso handler.
r8152: stop submitting intr for -EPROTO
netfilter: nft_reject_bridge: restrict reject to prerouting and input
netfilter: nft_reject_bridge: don't use IP stack to reject traffic
netfilter: nf_reject_ipv6: split nf_send_reset6() in smaller functions
netfilter: nf_reject_ipv4: split nf_send_reset() in smaller functions
netfilter: nf_tables_bridge: update hook_mask to allow {pre,post}routing
drivers/net: macvtap and tun depend on INET
drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets
drivers/net: Disable UFO through virtio
net: skb_fclone_busy() needs to detect orphaned skb
gre: Use inner mac length when computing tunnel length
mlx4: Avoid leaking steering rules on flow creation error flow
net/mlx4_en: Don't attempt to TX offload the outer UDP checksum for VXLAN
...
Linus Torvalds [Fri, 31 Oct 2014 22:00:48 +0000 (15:00 -0700)]
Merge git://git./linux/kernel/git/davem/sparc
Pull sparc update from David Miller:
"Two changes:
1) It makes no sense to execute a VTOC partition table request in the
Sun virtual block device driver and fail to load if it doesn't
succeed because a) we don't use the result at all and b) it won't
succeed if there is an EFI partition on the disk, for example.
We read the partition table via the normal means in the block layer
anyways, so this is really completely useless, so just remove it.
From Dwight Engen.
2) Hook up new bpf system call"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sunvdc: don't call VD_OP_GET_VTOC
sparc: Hook up bpf system call.
Linus Torvalds [Fri, 31 Oct 2014 21:43:42 +0000 (14:43 -0700)]
Merge tag 'microblaze-3.18-rc3' of git://git.monstr.eu/linux-2.6-microblaze
Pull Microblaze updates from Michal Simek:
- wire-up new bpf syscall
- fix PCI bug
- fix Kconfig warning
* tag 'microblaze-3.18-rc3' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Wire up bpf syscall
microblaze: Fix IO space breakage after of_pci_range_to_resource() change
microblaze: Fix missing NR_CPUS in menuconfig
Linus Torvalds [Fri, 31 Oct 2014 21:30:16 +0000 (14:30 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Fixes from all around the place:
- hyper-V 32-bit PAE guest kernel fix
- two IRQ allocation fixes on certain x86 boards
- intel-mid boot crash fix
- intel-quark quirk
- /proc/interrupts duplicate irq chip name fix
- cma boot crash fix
- syscall audit fix
- boot crash fix with certain TSC configurations (seen on Qemu)
- smpboot.c build warning fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, pageattr: Prevent overflow in slow_virt_to_phys() for X86_PAE
ACPI, irq, x86: Return IRQ instead of GSI in mp_register_gsi()
x86, intel-mid: Create IRQs for APB timers and RTC timers
x86: Don't enable F00F workaround on Intel Quark processors
x86/irq: Fix XT-PIC-XT-PIC in /proc/interrupts
x86, cma: Reserve DMA contiguous area after initmem_init()
i386/audit: stop scribbling on the stack frame
x86, apic: Handle a bad TSC more gracefully
x86: ACPI: Do not translate GSI number if IOAPIC is disabled
x86/smpboot: Move data structure to its primary usage scope
Rafael J. Wysocki [Fri, 31 Oct 2014 21:25:07 +0000 (22:25 +0100)]
Merge branches 'pm-cpufreq' and 'pm-sleep'
* pm-cpufreq:
cpufreq: cpufreq-dt: Restore default cpumask_setall(policy->cpus)
cpufreq: cpufreq-dt: disable unsupported OPPs
* pm-sleep:
PM / Sleep: fix recovery during resuming from hibernation
PM / Sleep: fix async suspend_late/freeze_late error handling
Rafael J. Wysocki [Fri, 31 Oct 2014 21:24:44 +0000 (22:24 +0100)]
Merge branches 'acpi-scan' and 'acpi-ec'
* acpi-scan:
ACPI: Use ACPI companion to match only the first physical device
* acpi-ec:
ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer.
Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC"
Linus Torvalds [Fri, 31 Oct 2014 21:05:35 +0000 (14:05 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Various scheduler fixes all over the place: three SCHED_DL fixes,
three sched/numa fixes, two generic race fixes and a comment fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/dl: Fix preemption checks
sched: Update comments for CLONE_NEWNS
sched: stop the unbound recursion in preempt_schedule_context()
sched/fair: Fix division by zero sysctl_numa_balancing_scan_size
sched/fair: Care divide error in update_task_scan_period()
sched/numa: Fix unsafe get_task_struct() in task_numa_assign()
sched/deadline: Fix races between rt_mutex_setprio() and dl_task_timer()
sched/deadline: Don't replenish from a !SCHED_DEADLINE entity
sched: Fix race between task_group and sched_task_group
Linus Torvalds [Fri, 31 Oct 2014 21:01:47 +0000 (14:01 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, plus on the kernel side:
- a revert for a newly introduced PMU driver which isn't complete yet
and where we ran out of time with fixes (to be tried again in
v3.19) - this makes up for a large chunk of the diffstat.
- compilation warning fixes
- a printk message fix
- event_idx usage fixes/cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Trivial typo fix for --demangle
perf tools: Fix report -F dso_from for data without branch info
perf tools: Fix report -F dso_to for data without branch info
perf tools: Fix report -F symbol_from for data without branch info
perf tools: Fix report -F symbol_to for data without branch info
perf tools: Fix report -F mispredict for data without branch info
perf tools: Fix report -F in_tx for data without branch info
perf tools: Fix report -F abort for data without branch info
perf tools: Make CPUINFO_PROC an array to support different kernel versions
perf callchain: Use global caching provided by libunwind
perf/x86/intel: Revert incomplete and undocumented Broadwell client support
perf/x86: Fix compile warnings for intel_uncore
perf: Fix typos in sample code in the perf_event.h header
perf: Fix and clean up initialization of pmu::event_idx
perf: Fix bogus kernel printk
perf diff: Add missing hists__init() call at tool start
Linus Torvalds [Fri, 31 Oct 2014 20:57:45 +0000 (13:57 -0700)]
Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull futex fixes from Ingo Molnar:
"This contains two futex fixes: one fixes a race condition, the other
clarifies shared/private futex comments"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Fix a race condition between REQUEUE_PI and task death
futex: Mention key referencing differences between shared and private futexes
David S. Miller [Fri, 31 Oct 2014 20:18:35 +0000 (16:18 -0400)]
Merge tag 'master-2014-10-30' of git://git./linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-10-31
Please pull this small batch of spooky fixes intended for the 3.18
stream...boo!
Cyril Brulebois adds an rt2x00 device ID.
Dan Carpenter provides a one-line masking fix for an ath9k debugfs
entry.
Larry Finger gives us a package of small rtlwifi fixes which add some
bits that were left out of some feature updates that were included
in the merge window. Hopefully this isn't a sign that the rtlwifi
base is getting too big...
Marc Yang brings a fix for a temporary mwifiex stall when doing 11n
RX reordering.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennart Sorensen [Fri, 31 Oct 2014 17:38:52 +0000 (13:38 -0400)]
drivers: net: cpsw: Support ALLMULTI and fix IFF_PROMISC in switch mode
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work. Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.
A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.
With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennart Sorensen [Fri, 31 Oct 2014 17:28:54 +0000 (13:28 -0400)]
drivers: net: cpsw: Fix broken loop condition in switch mode
0d961b3b52f566f823070ce2366511a7f64b928c (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.
It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.
However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.
Putting the loop condition back in the switch mode section fixes it.
A comment has been added to point out the intent clearly to avoid future
confusion. Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Fri, 31 Oct 2014 03:50:15 +0000 (20:50 -0700)]
net: ethtool: Return -EOPNOTSUPP if user space tries to read EEPROM with lengh 0
If a driver supports reading EEPROM but no EEPROM is installed in the system,
the driver's get_eeprom_len function returns 0. ethtool will subsequently
try to read that zero-length EEPROM anyway. If the driver does not support
EEPROM access at all, this operation will return -EOPNOTSUPP. If the driver
does support EEPROM access but no EEPROM is installed, the operation will
return -EINVAL. Return -EOPNOTSUPP in both cases for consistency.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko [Fri, 31 Oct 2014 16:28:03 +0000 (18:28 +0200)]
stmmac: pci: set default of the filter bins
The commit
3b57de958e2a brought the support for a different amount of the
filter bins, but didn't update the PCI driver accordingly. This patch appends
the default values when the device is enumerated via PCI bus.
Fixes:
3b57de958e2a (net: stmmac: Support devicetree configs for mcast and ucast filter entries)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lindgren [Thu, 30 Oct 2014 16:59:27 +0000 (09:59 -0700)]
net: smc91x: Fix gpios for device tree based booting
With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.
Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.
And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dwight Engen [Thu, 30 Oct 2014 19:55:35 +0000 (15:55 -0400)]
sunvdc: don't call VD_OP_GET_VTOC
The VD_OP_GET_VTOC operation will succeed only if the vdisk backend has a
VTOC label, otherwise it will fail. In particular, it will return error
48 (ENOTSUP) if the disk has an EFI label. VTOC disk labels are already
handled by directly reading the disk in block/partitions/sun.c (enabled by
CONFIG_SUN_PARTITION which defaults to y on SPARC). Since port->label is
unused in the driver, remove the call and the field.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar [Thu, 30 Oct 2014 07:50:04 +0000 (00:50 -0700)]
mpls: Allow mpls_gso to be built as module
Kconfig already allows mpls to be built as module. Following patch
fixes Makefile to do same.
CC: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar [Thu, 30 Oct 2014 07:49:57 +0000 (00:49 -0700)]
mpls: Fix mpls_gso handler.
mpls gso handler needs to pull skb after segmenting skb.
CC: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 31 Oct 2014 19:43:52 +0000 (12:43 -0700)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull core fixes from Ingo Molnar:
"The tree contains two RCU fixes and a compiler quirk comment fix"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Make rcu_barrier() understand about missing rcuo kthreads
compiler/gcc4+: Remove inaccurate comment about 'asm goto' miscompiles
rcu: More on deadlock between CPU hotplug and expedited grace periods
Linus Torvalds [Fri, 31 Oct 2014 19:33:05 +0000 (12:33 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"As you requested in the rc2 release mail the timer department serves
you a few real bug fixes:
- Fix the probe logic of the architected arm/arm64 timer
- Plug a stack info leak in posix-timers
- Prevent a shift out of bounds issue in the clockevents core"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ARM/ARM64: arch-timer: fix arch_timer_probed logic
clockevents: Prevent shift out of bounds
posix-timers: Fix stack info leak in timer_create()
Linus Torvalds [Fri, 31 Oct 2014 19:28:38 +0000 (12:28 -0700)]
Merge tag 'trace-fixes-v3.18-rc1-2' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"ARM has system calls outside the NR_syscalls range, and the generic
tracing system does not support that and without checks, it can cause
an oops to be reported.
Rabin Vincent added checks in the return code on syscall events to
make sure that the system call number is within the range that tracing
knows about, and if not, simply ignores the system call.
The system call tracing infrastructure needs to be rewritten to handle
these cases better, but for now, to keep from oopsing, this patch will
do"
* tag 'trace-fixes-v3.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/syscalls: Ignore numbers outside NR_syscalls' range
Linus Torvalds [Fri, 31 Oct 2014 18:55:40 +0000 (11:55 -0700)]
Merge tag 'docs-for-linus' of git://git.lwn.net/linux-2.6
Pull documentation fixes from Jonathan Corbet:
"So this is my first pull request since I rashly agreed to look after
the documentation subtree. It contains some typo fixes, a few minor
documentation improvements, and, most importantly, fixes for a couple
of build problems in various bits of sample code.
I fully intend to start sending pull requests with signed tags.
However, due to poor planning on my part and the general obnoxiousness
of life, I'm 2000 miles away from my private key which is sitting on a
powered-down machine. This should be fixed before my next request.
Meanwhile git.lwn.net is a machine under my control, the patches are
all trivial, and all have done time in linux-next"
* tag 'docs-for-linus' of git://git.lwn.net/linux-2.6:
Documentation/SubmittingPatches: Reported-by tags and permission
Documentation: remove outdated references to the linux-next wiki
Documentation: Restrict TSC test code to x86
doc: kernel-parameters.txt: Add ide-generic.probe-mask
vdso: don't require 64-bit math in standalone test
Documentation: Add CONFIG_DEBUG_KMEMLEAK_DEFAULT_OFF case
Documentation: Add default kmemleak off case in kernel-parameters.txt
Docs: Document that the sticky bit is understood by hugetlbfs
DocBook: Reduce noise from make cleandocs
Documentation: fix vdso_standalone_test_x86 on 32-bit
Documentation: dt-bindings: Explain order in patch series
Documentation/ABI/testing/sysfs-ibft: fix a typo
hayeswang [Fri, 31 Oct 2014 05:35:57 +0000 (13:35 +0800)]
r8152: stop submitting intr for -EPROTO
For Renesas USB 3.0 host controller, when unplugging the usb hub which
has the RTL8153 plugged, the driver would get -EPROTO for interrupt
transfer. There is high probability to get the information of "HC died;
cleaning up", if the driver continues to submit the interrupt transfer
before the disconnect() is called.
[ 1024.197678] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.213673] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.229668] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.245661] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.261653] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.277648] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.293642] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.309638] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.325633] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.341627] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.357621] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.373615] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.383097] usb 9-1: USB disconnect, device number 2
[ 1024.383103] usb 9-1.4: USB disconnect, device number 6
[ 1029.391010] xhci_hcd 0000:04:00.0: xHCI host not responding to stop endpoint command.
[ 1029.391016] xhci_hcd 0000:04:00.0: Assuming host is dying, halting host.
[ 1029.392551] xhci_hcd 0000:04:00.0: HC died; cleaning up
[ 1029.421480] usb 8-1: USB disconnect, device number 2
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Torokhov [Fri, 31 Oct 2014 16:35:53 +0000 (09:35 -0700)]
Revert "Input: i8042 - disable active multiplexing by default"
This reverts commit
68da166491655bc54051bf04c78ce648e2e33508.
It turns out that the assertion about scope of regressions due to
always keeping keyboard controller in legacy mode was proven wrong.
There are laptops, such as Clevo W650SH, that only have internal
touchpad (no external PS/2 ports), that require active multiplexing
mode to switch the touchpad (Elantech) into native mode instead of
basic PS/2 emulation.
Reported-by: Roel Aaij <roel.aaij@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>