OSDN Git Service
Krzysztof Kozlowski [Fri, 10 Mar 2023 21:46:28 +0000 (22:46 +0100)]
net: stmmac: qcom: drop of_match_ptr for ID table
The driver is specific to ARCH_QCOM which depends on OF thus the driver
is OF-only. Its of_device_id table is built unconditionally, thus
of_match_ptr() for ID table does not make sense.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 15 Mar 2023 08:00:35 +0000 (08:00 +0000)]
Merge branch 'dsa-microchip-tc-ets'
Oleksij Rempel says:
====================
net: dsa: microchip: tc-ets support
changes v3:
- add tc_ets_supported to match supported devices
- dynamically regenerated default TC to queue map.
- add Acked-by to the first patch
changes v2:
- run egress limit configuration on all queue separately. Otherwise
configuration may not apply correctly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksij Rempel [Fri, 10 Mar 2023 09:08:09 +0000 (10:08 +0100)]
net: dsa: microchip: add ETS Qdisc support for KSZ9477 series
Add ETS Qdisc support for KSZ9477 of switches. Current implementation is
limited to strict priority mode.
Tested on KSZ8563R with following configuration:
tc qdisc replace dev lan2 root handle 1: ets strict 4 \
priomap 3 3 2 2 1 1 0 0
ip link add link lan2 name v1 type vlan id 1 \
egress-qos-map 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7
and patched iperf3 version:
https://github.com/esnet/iperf/pull/1476
iperf3 -c 172.17.0.1 -b100M -l1472 -t100 -u -R --sock-prio 2
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksij Rempel [Fri, 10 Mar 2023 09:08:08 +0000 (10:08 +0100)]
net: dsa: microchip: add ksz_setup_tc_mode() function
Add ksz_setup_tc_mode() to make queue scheduling and shaping
configuration more visible.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 15 Mar 2023 07:37:34 +0000 (00:37 -0700)]
Merge branch 'ipv6-optimize-rt6_score_route'
Eric Dumazet says:
====================
ipv6: optimize rt6_score_route()
This patch series remove an expensive rwlock acquisition
in rt6_check_neigh()/rt6_score_route().
First patch adds missing annotations, and second patch implements
the optimization.
====================
Link: https://lore.kernel.org/r/20230313201732.887488-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Mon, 13 Mar 2023 20:17:32 +0000 (20:17 +0000)]
ipv6: remove one read_lock()/read_unlock() pair in rt6_check_neigh()
rt6_check_neigh() uses read_lock() to protect n->nud_state reading.
This seems overkill and causes false sharing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Mon, 13 Mar 2023 20:17:31 +0000 (20:17 +0000)]
neighbour: annotate lockless accesses to n->nud_state
We have many lockless accesses to n->nud_state.
Before adding another one in the following patch,
add annotations to readers and writers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Horatiu Vultur [Sun, 12 Mar 2023 19:51:55 +0000 (20:51 +0100)]
net: lan966x: Change lan966x_police_del return type
As the function always returns 0 change the return type to be
void instead of int. In this way also remove a wrong message
in case of error which would never happen.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230312195155.1492881-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rob Herring [Fri, 10 Mar 2023 14:47:16 +0000 (08:47 -0600)]
net: Use of_property_present() for testing DT property presence
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230310144716.1544083-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 14 Mar 2023 00:03:19 +0000 (17:03 -0700)]
Merge branch '40GbE' of git://git./linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
i40e: support XDP multi-buffer
Tirthendu Sarkar says:
This patchset adds multi-buffer support for XDP. Tx side already has
support for multi-buffer. This patchset focuses on Rx side. The last
patch contains actual multi-buffer changes while the previous ones are
preparatory patches.
On receiving the first buffer of a packet, xdp_buff is built and its
subsequent buffers are added to it as frags. While 'next_to_clean' keeps
pointing to the first descriptor, the newly introduced 'next_to_process'
keeps track of every descriptor for the packet.
On receiving EOP buffer the XDP program is called and appropriate action
is taken (building skb for XDP_PASS, reusing page for XDP_DROP, adjusting
page offsets for XDP_{REDIRECT,TX}).
The patchset also streamlines page offset adjustments for buffer reuse
to make it easier to post process the rx_buffers after running XDP prog.
With this patchset there does not seem to be any performance degradation
for XDP_PASS and some improvement (~1% for XDP_TX, ~5% for XDP_DROP) when
measured using xdp_rxq_info program from samples/bpf/ for 64B packets.
v1: https://lore.kernel.org/netdev/
20230306210822.
3381942-1-anthony.l.nguyen@intel.com/
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
i40e: add support for XDP multi-buffer Rx
i40e: add xdp_buff to i40e_ring struct
i40e: introduce next_to_process to i40e_ring
i40e: use frame_sz instead of recalculating truesize for building skb
i40e: Change size to truesize when using i40e_rx_buffer_flip()
i40e: add pre-xdp page_count in rx_buffer
i40e: change Rx buffer size for legacy-rx to support XDP multi-buffer
i40e: consolidate maximum frame size calculation for vsi
====================
Link: https://lore.kernel.org/r/20230309212819.1198218-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pedro Tammela [Thu, 9 Mar 2023 17:55:54 +0000 (14:55 -0300)]
selftests: tc-testing: add tests for action binding
Add tests that check if filters can bind actions, that is create an
action independently and then bind to a filter.
tdc-tests under category 'infra':
1..18
ok 1 abdc - Reference pedit action object in filter
ok 2 7a70 - Reference mpls action object in filter
ok 3 d241 - Reference bpf action object in filter
ok 4 383a - Reference connmark action object in filter
ok 5 c619 - Reference csum action object in filter
ok 6 a93d - Reference ct action object in filter
ok 7 8bb5 - Reference ctinfo action object in filter
ok 8 2241 - Reference gact action object in filter
ok 9 35e9 - Reference gate action object in filter
ok 10 b22e - Reference ife action object in filter
ok 11 ef74 - Reference mirred action object in filter
ok 12 2c81 - Reference nat action object in filter
ok 13 ac9d - Reference police action object in filter
ok 14 68be - Reference sample action object in filter
ok 15 cf01 - Reference skbedit action object in filter
ok 16 c109 - Reference skbmod action object in filter
ok 17 4abc - Reference tunnel_key action object in filter
ok 18 dadd - Reference vlan action object in filter
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Link: https://lore.kernel.org/r/20230309175554.304824-1-pctammela@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Maxim Korotkov [Thu, 9 Mar 2023 17:43:47 +0000 (20:43 +0300)]
bnxt: avoid overflow in bnxt_get_nvram_directory()
The value of an arithmetic expression is subject
of possible overflow due to a failure to cast operands to a larger data
type before performing arithmetic. Used macro for multiplication instead
operator for avoiding overflow.
Found by Security Code and Linux Verification
Center (linuxtesting.org) with SVACE.
Signed-off-by: Maxim Korotkov <korotkov.maxim.s@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230309174347.3515-1-korotkov.maxim.s@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jiri Pirko [Thu, 9 Mar 2023 09:45:59 +0000 (10:45 +0100)]
net: virtio_net: implement exact header length guest feature
Virtio spec introduced a feature VIRTIO_NET_F_GUEST_HDRLEN which when
set implicates that device benefits from knowing the exact size
of the header. For compatibility, to signal to the device that
the header is reliable driver also needs to set this feature.
Without this feature set by driver, device has to figure
out the header size itself.
Quoting the original virtio spec:
"hdr_len is a hint to the device as to how much of the header needs to
be kept to copy into each packet"
"a hint" might not be clear for the reader what does it mean, if it is
"maybe like that" of "exactly like that". This feature just makes it
crystal clear and let the device count on the hdr_len being filled up
by the exact length of header.
Also note the spec already has following note about hdr_len:
"Due to various bugs in implementations, this field is not useful
as a guarantee of the transport header size."
Without this feature the device needs to parse the header in core
data path handling. Accurate information helps the device to eliminate
such header parsing and directly use the hardware accelerators
for GSO operation.
virtio_net_hdr_from_skb() fills up hdr_len to skb_headlen(skb).
The driver already complies to fill the correct value. Introduce the
feature and advertise it.
Note that virtio spec also includes following note for device
implementation:
"Caution should be taken by the implementation so as to prevent
a malicious driver from attacking the device by setting
an incorrect hdr_len."
There is a plan to support this feature in our emulated device.
A device of SolidRun offers this feature bit. They claim this feature
will save the device a few cycles for every GSO packet.
Link: https://docs.oasis-open.org/virtio/virtio/v1.2/cs01/virtio-v1.2-cs01.html#x1-230006x3
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Alvaro Karsz <alvaro.karsz@solid-run.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20230309094559.917857-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kristian Overskeid [Thu, 9 Mar 2023 09:23:02 +0000 (10:23 +0100)]
net: hsr: Don't log netdev_err message on unknown prp dst node
If no frames has been exchanged with a node for HSR_NODE_FORGET_TIME, the
node will be deleted from the node_db list. If a frame is sent to the node
after it is deleted, a netdev_err message for each slave interface is
produced. This should not happen with dan nodes because of supervision
frames, but can happen often with san nodes, which clutters the kernel
log. Since the hsr protocol does not support sans, this is only relevant
for the prp protocol.
Signed-off-by: Kristian Overskeid <koverskeid@gmail.com>
Link: https://lore.kernel.org/r/20230309092302.179586-1-koverskeid@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit [Wed, 8 Mar 2023 20:34:13 +0000 (21:34 +0100)]
net: phy: smsc: use device_property_present in smsc_phy_probe
Use unified device property API.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/a969f012-1d3b-7a36-51cf-89a5f8f15a9b@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vincenzo Palazzo [Fri, 10 Mar 2023 22:18:51 +0000 (23:18 +0100)]
net: socket: suppress unused warning
suppress unused warnings and fix the error that there is
with the W=1 enabled.
Warning generated
net/socket.c: In function ‘__sys_getsockopt’:
net/socket.c:2300:13: error: variable ‘max_optlen’ set but not used [-Werror=unused-but-set-variable]
2300 | int max_optlen;
Signed-off-by: Vincenzo Palazzo <vincenzopalazzodev@gmail.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230310221851.304657-1-vincenzopalazzodev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexander Stein [Fri, 10 Mar 2023 07:45:00 +0000 (08:45 +0100)]
net: phy: dp83867: Disable IRQs on suspend
Before putting the PHY into IEEE power down mode, disable IRQs to
prevent accessing the PHY once MDIO has already been shutdown.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230310074500.3472858-1-alexander.stein@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Horatiu Vultur [Tue, 7 Mar 2023 21:44:02 +0000 (22:44 +0100)]
net: phy: micrel: Add support for PTP_PF_PEROUT for lan8841
Lan8841 has 10 GPIOs and it has 2 events(EVENT_A and EVENT_B). It is
possible to assigned the 2 events to any of the GPIOs, but a GPIO can
have only 1 event at a time.
These events are used to generate periodic signals. It is possible to
configure the length, the start time and the period of the signal by
configuring the event.
Currently the SW uses only EVENT_A to generate the perout.
These events are generated by comparing the target time with the PHC
time. In case the PHC time is changed to a value bigger than the target
time + reload time, then it would generate only 1 event and then it
would stop because target time + reload time is small than PHC time.
Therefore it is required to change also the target time every time when
the PHC is changed. The same will apply also when the PHC time is
changed to a smaller value.
This was tested using:
testptp -L 6,2
testptp -p
1000000000 -w
200000000
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230307214402.793057-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Muhammad Usama Anjum [Thu, 9 Mar 2023 22:52:05 +0000 (03:52 +0500)]
qede: remove linux/version.h and linux/compiler.h
make versioncheck reports the following:
./drivers/net/ethernet/qlogic/qede/qede.h: 10 linux/version.h not needed.
./drivers/net/ethernet/qlogic/qede/qede_ethtool.c: 7 linux/version.h not needed.
So remove linux/version.h from both of these files. Also remove
linux/compiler.h while at it as it is also not being used.
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230309225206.2473644-1-usama.anjum@collabora.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Edward Cree [Thu, 9 Mar 2023 11:59:04 +0000 (11:59 +0000)]
sfc: support offloading TC VLAN push/pop actions to the MAE
EF100 can pop and/or push up to two VLAN tags.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230309115904.56442-1-edward.cree@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 11 Mar 2023 05:25:04 +0000 (21:25 -0800)]
Merge branch 'update-cpsw-bindings-for-serdes-phy'
Siddharth Vadapalli says:
====================
Update CPSW bindings for Serdes PHY
This series adds documentation for the Serdes PHY. Also, the name used to
refer to the Serdes PHY in the am65-cpsw driver is updated to match the
documented name.
Documenting the Serdes PHY bindings was missed out in the already merged
series at:
https://lore.kernel.org/r/
20230104103432.
1126403-1-s-vadapalli@ti.com/
This miss was pointed out at:
https://lore.kernel.org/r/CAMuHMdW5atq-FuLEL3htuE3t2uO86anLL3zeY7n1RqqMP_rH1g@mail.gmail.com/
v2:
https://lore.kernel.org/r/
20230308051835.276552-1-s-vadapalli@ti.com/
v1:
https://lore.kernel.org/r/
20230306094750.159657-1-s-vadapalli@ti.com/
====================
Link: https://lore.kernel.org/r/20230309073612.431287-1-s-vadapalli@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Siddharth Vadapalli [Thu, 9 Mar 2023 07:36:12 +0000 (13:06 +0530)]
net: ethernet: ti: am65-cpsw: Update name of Serdes PHY
The bindings for the am65-cpsw driver use the name "serdes" to refer to
the Serdes PHY. Thus, update the name used for the Serdes PHY within the
am65_cpsw_init_serdes_phy() function from "serdes-phy" to "serdes".
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Siddharth Vadapalli [Thu, 9 Mar 2023 07:36:11 +0000 (13:06 +0530)]
dt-bindings: net: ti: k3-am654-cpsw-nuss: Document Serdes PHY
Update bindings to include Serdes PHY as an optional PHY, in addition to
the existing CPSW MAC's PHY. The CPSW MAC's PHY is required while the
Serdes PHY is optional. The Serdes PHY handle has to be provided only
when the Serdes is being configured in a Single-Link protocol. Using the
name "serdes-phy" to represent the Serdes PHY handle, the am65-cpsw-nuss
driver can obtain the Serdes PHY and request the Serdes to be
configured.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vadim Fedorenko [Thu, 9 Mar 2023 10:54:21 +0000 (02:54 -0800)]
ptp_ocp: add force_irq to xilinx_spi configuration
Flashing firmware via devlink flash was failing on PTP OCP devices
because it is using Quad SPI mode, but the driver was not properly
behaving. With force_irq flag landed it now can be fixed.
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Link: https://lore.kernel.org/r/20230309105421.2953451-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 11 Mar 2023 02:22:28 +0000 (18:22 -0800)]
Merge tag 'wireless-next-2023-03-10' of git://git./linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
wireless-next patches for 6.4
Major changes:
cfg80211
* 6 GHz improvements
* HW timestamping support
* support for randomized auth/deauth TA for PASN privacy
(also for mac80211)
mac80211
* radiotap TLV and EHT support for the iwlwifi sniffer
* HW timestamping support
* per-link debugfs for multi-link
brcmfmac
* support for Apple (M1 Pro/Max) devices
iwlwifi
* support for a few new devices
* EHT sniffer support
rtw88
* better support for some SDIO devices
(e.g. MAC address from efuse)
rtw89
* HW scan support for 8852b
* better support for 6 GHz scanning
* tag 'wireless-next-2023-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (84 commits)
wifi: iwlwifi: mvm: fix EOF bit reporting
wifi: iwlwifi: Do not include radiotap EHT user info if not needed
wifi: iwlwifi: mvm: add EHT RU allocation to radiotap
wifi: iwlwifi: Update logs for yoyo reset sw changes
wifi: iwlwifi: mvm: clean up duplicated defines
wifi: iwlwifi: rs-fw: break out for unsupported bandwidth
wifi: iwlwifi: Add support for B step of BnJ-Fm4
wifi: iwlwifi: mvm: make flush code a bit clearer
wifi: iwlwifi: mvm: avoid UB shift of snif_queue
wifi: iwlwifi: mvm: add primary 80 known for EHT radiotap
wifi: iwlwifi: mvm: parse FW frame metadata for EHT sniffer mode
wifi: iwlwifi: mvm: decode USIG_B1_B7 RU to nl80211 RU width
wifi: iwlwifi: mvm: rename define to generic name
wifi: iwlwifi: mvm: allow Microsoft to use TAS
wifi: iwlwifi: mvm: add all EHT based on data0 info from HW
wifi: iwlwifi: mvm: add EHT radiotap info based on rate_n_flags
wifi: iwlwifi: mvm: add an helper function radiotap TLVs
wifi: radiotap: separate vendor TLV into header/content
wifi: iwlwifi: reduce verbosity of some logging events
wifi: iwlwifi: Adding the code to get RF name for MsP device
...
====================
Link: https://lore.kernel.org/r/20230310120159.36518-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 11 Mar 2023 02:12:50 +0000 (18:12 -0800)]
Merge branch 'rework-sfp-a2-access-conditionals'
Russell King says:
====================
Rework SFP A2 access conditionals
This series reworks the SFP A2 (diagnostics and control) access so we
don't end up testing a variable number of conditions in several places.
This also resolves a minor issue where we may have a module indicating
that it is not SFF8472 compliant, doesn't implement A2, but fails to
set the enhanced option byte to zero, leading to accesses to the A2
page that fail.
The first patch adds a new flag "have_a2" which indicates whether we
should be accessing the A2 page, and uses this for hwmon. The
conditions are kept the same.
The second patch extends the check for soft-state polling and control
by using this "have_a2" flag (which effectively augments the check to
include some level of SFF8472 compliance.)
====================
Link: https://lore.kernel.org/r/ZAoBnqGBnIZzLwpV@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Thu, 9 Mar 2023 15:57:16 +0000 (15:57 +0000)]
net: sfp: only use soft polling if we have A2h access
The soft state bits are stored in the A2h memory space, and require
SFF-8472 compliance. This is what our have_a2 flag tells us, so use
this to indicate whether we should attempt to use the soft signals.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Thu, 9 Mar 2023 15:57:11 +0000 (15:57 +0000)]
net: sfp: add A2h presence flag
The hwmon code wants to know when it is safe to access the A2h data
stored in a separate address. We indicate that this is present when
we have SFF-8472 compliance and the lack of an address-change
sequence.,
The same conditions are also true if we want to access other controls
and status in the A2h address. So let's make a flag to indicate whether
we can access it, instead of repeating the conditions throughout the
code.
For now, only convert the hwmon code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 11 Mar 2023 00:49:24 +0000 (16:49 -0800)]
Merge branch 'couple-of-minor-improvements-to-build_skb-variants'
Gal Pressman says:
====================
Couple of minor improvements to build_skb variants
First patch replaces open-coded occurrences of
skb_propagate_pfmemalloc() in build_skb() and build_skb_around().
The secnod patch adds a likely() to the skb allocation in build_skb().
====================
Link: https://lore.kernel.org/r/20230308131720.2103611-1-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman [Wed, 8 Mar 2023 13:17:20 +0000 (15:17 +0200)]
skbuff: Add likely to skb pointer in build_skb()
Similarly to napi_build_skb(), it is likely the skb allocation in
build_skb() succeeded. frag_size != 0 is also likely, as stated in
__build_skb_around().
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman [Wed, 8 Mar 2023 13:17:19 +0000 (15:17 +0200)]
skbuff: Replace open-coded skb_propagate_pfmemalloc()s
Use skb_propagate_pfmemalloc() in build_skb()/build_skb_around() instead
of open-coding it.
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jens Axboe [Wed, 8 Mar 2023 04:18:21 +0000 (21:18 -0700)]
tap: add support for IOCB_NOWAIT
The tap driver already supports passing in nonblocking state based
on O_NONBLOCK, add support for checking IOCB_NOWAIT as well. With that
done, we can flag it with FMODE_NOWAIT as well.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/8f859870-e6e2-09ca-9c0f-a2aa7c984fb2@kernel.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jens Axboe [Wed, 8 Mar 2023 03:45:56 +0000 (20:45 -0700)]
tun: flag the device as supporting FMODE_NOWAIT
tun already checks for both O_NONBLOCK and IOCB_NOWAIT in its read
and write iter handlers, so it's fully ready for FMODE_NOWAIT. But
for some reason it doesn't set it. Rectify that oversight.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/3f7dc1f0-79ca-d85c-4d16-8c12c5bd492d@kernel.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 11 Mar 2023 00:44:26 +0000 (16:44 -0800)]
Merge branch 'net-lan966x-add-support-for-is1-vcap'
Horatiu Vultur says:
====================
net: lan966x: Add support for IS1 VCAP
Provide the Ingress Stage 1 (IS1) VCAP (Versatile Content-Aware
Processor) support for the Lan966x platform.
The IS1 VCAP has 3 lookups and they are accessible with a TC chain id:
- chain
1000000: IS1 Lookup 0
- chain
1100000: IS1 Lookup 1
- chain
1200000: IS1 Lookup 2
The IS1 is capable of different actions like rewrite VLAN tags, change
priority of the frames, police the traffic, etc. These features will be
added at a later point.
The IS1 currently implements the action that allows setting the value
of a PAG (Policy Association Group) key field in the frame metadata and
this can be used for matching in an IS2 VCAP rule. In this way a rule in
IS0 VCAP can be linked to rules in the IS2 VCAP. The linking is exposed
by using the TC "goto chain" action with an offset from the IS2 chain ids.
For example "goto chain
8000001" will use a PAG value of 1 to chain to a
rule in IS2 lookup 0.
====================
Link: https://lore.kernel.org/r/20230307220929.834219-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Horatiu Vultur [Tue, 7 Mar 2023 22:09:29 +0000 (23:09 +0100)]
net: lan966x: Add support for IS1 VCAP ethernet protocol types
IS1 VCAP has it's own list of supported ethernet protocol types which is
different than the IS2 VCAP. Therefore separate the list of known
protocol types based on the VCAP type.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Horatiu Vultur [Tue, 7 Mar 2023 22:09:28 +0000 (23:09 +0100)]
net: lan966x: Add TC filter chaining support for IS1 and IS2 VCAPs
Allow rules to be chained between IS1 VCAP and IS2 VCAP. Chaining
between IS1 lookups or between IS2 lookups are not supported by the
hardware.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Horatiu Vultur [Tue, 7 Mar 2023 22:09:27 +0000 (23:09 +0100)]
net: lan966x: Add TC support for IS1 VCAP
Enable TC command to use IS1 VCAP
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Horatiu Vultur [Tue, 7 Mar 2023 22:09:26 +0000 (23:09 +0100)]
net: lan966x: Add IS1 VCAP keyset configuration for lan966x
Add IS1 VCAP port keyset configuration for lan966x and also update debug
fs support to show the keyset configuration.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Horatiu Vultur [Tue, 7 Mar 2023 22:09:25 +0000 (23:09 +0100)]
net: lan966x: Add IS1 VCAP model
Provide IS1 (ingress stage 1) VCAP model for lan966x.
This provides classification actions for lan966x.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Miquel Raynal [Tue, 7 Mar 2023 19:29:27 +0000 (20:29 +0100)]
net: mvpp2: Defer probe if MAC address source is not yet ready
NVMEM layouts are no longer registered early, and thus may not yet be
available when Ethernet drivers (or any other consumer) probe, leading
to possible probe deferrals errors. Forward the error code if this
happens. All other errors being discarded, the driver will eventually
use a random MAC address if no other source was considered valid (no
functional change on this regard).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20230307192927.512757-1-miquel.raynal@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 22:10:51 +0000 (16:10 -0600)]
net: restore alpha order to Ethernet devices in config
The filename "wangxun" sorts between "intel" and "xscale", but
xscale/Kconfig contains "Intel XScale" prompts, so Wangxun ends up in the
wrong place in the config front-ends.
Move wangxun/Kconfig so the Wangxun devices appear in order in the user
interface.
Fixes:
3ce7547e5b71 ("net: txgbe: Add build support for txgbe")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20230307221051.890135-1-helgaas@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 10 Mar 2023 07:35:49 +0000 (23:35 -0800)]
Merge branch '1GbE' of git://git./linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-07 (igc)
This series contains updates to igc driver only.
Muhammad adds tracking and reporting of QBV config errors.
Tan Tee adds support for configuring max SDU for each Tx queue.
Sasha removes check for alternate media as only one media type is
supported.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igc: Clean up and optimize watchdog task
igc: offload queue max SDU from tc-taprio
igc: Add qbv_config_change_errors counter
====================
Link: https://lore.kernel.org/r/20230307221332.3997881-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jason Xing [Wed, 8 Mar 2023 02:11:53 +0000 (10:11 +0800)]
udp: introduce __sk_mem_schedule() usage
Keep the accounting schema consistent across different protocols
with __sk_mem_schedule(). Besides, it adjusts a little bit on how
to calculate forward allocated memory compared to before. After
applied this patch, we could avoid receive path scheduling extra
amount of memory.
Link: https://lore.kernel.org/lkml/20230221110344.82818-1-kerneljasonxing@gmail.com/
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230308021153.99777-1-kerneljasonxing@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 10 Mar 2023 07:28:53 +0000 (23:28 -0800)]
Merge branch 'main' of git://git./linux/kernel/git/netfilter/nf-next
Florian Westphal says:
====================
Netfilter updates for net-next
1. nf_tables 'brouting' support, from Sriram Yagnaraman.
2. Update bridge netfilter and ovs conntrack helpers to handle
IPv6 Jumbo packets properly, i.e. fetch the packet length
from hop-by-hop extension header, from Xin Long.
This comes with a test BIG TCP test case, added to
tools/testing/selftests/net/.
3. Fix spelling and indentation in conntrack, from Jeremy Sowden.
* 'main' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: nat: fix indentation of function arguments
netfilter: conntrack: fix typo
selftests: add a selftest for big tcp
netfilter: use nf_ip6_check_hbh_len in nf_ct_skb_network_trim
netfilter: move br_nf_check_hbh_len to utils
netfilter: bridge: move pskb_trim_rcsum out of br_nf_check_hbh_len
netfilter: bridge: check len before accessing more nh data
netfilter: bridge: call pskb_may_pull in br_nf_check_hbh_len
netfilter: bridge: introduce broute meta statement
====================
Link: https://lore.kernel.org/r/20230308193033.13965-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geert Uytterhoeven [Wed, 8 Mar 2023 13:04:52 +0000 (14:04 +0100)]
net: ethernet: ti: am65-cpsw: Convert to devm_of_phy_optional_get()
Use the new devm_of_phy_optional_get() helper instead of open-coding the
same operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/01605ea233ff7fc09bb0ea34fc8126af73db83f9.1678280599.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Leon Romanovsky [Wed, 8 Mar 2023 09:23:13 +0000 (11:23 +0200)]
neighbour: delete neigh_lookup_nodev as not used
neigh_lookup_nodev isn't used in the kernel after removal
of DECnet. So let's remove it.
Fixes:
1202cdd66531 ("Remove DECnet support from kernel")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/eb5656200d7964b2d177a36b77efa3c597d6d72d.1678267343.git.leonro@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Wed, 8 Mar 2023 18:26:48 +0000 (18:26 +0000)]
net: sched: remove qdisc_watchdog->last_expires
This field mirrors hrtimer softexpires, we can instead
use the existing helpers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230308182648.1150762-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit [Wed, 8 Mar 2023 20:19:55 +0000 (21:19 +0100)]
net: phy: smsc: use phy_set_bits in smsc_phy_config_init
Simplify the code by using phy_set_bits().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/b64d9f86-d029-b911-bbe9-6ca6889399d7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Westphal [Wed, 8 Mar 2023 14:20:06 +0000 (15:20 +0100)]
netlink: remove unused 'compare' function
No users in the tree. Tested with allmodconfig build.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20230308142006.20879-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nick Alcock [Wed, 8 Mar 2023 12:12:29 +0000 (12:12 +0000)]
lib: packing: remove MODULE_LICENSE in non-modules
Since commit
8b41fc4454e ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230308121230.5354-1-nick.alcock@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nick Alcock [Wed, 8 Mar 2023 12:12:30 +0000 (12:12 +0000)]
mctp: remove MODULE_LICENSE in non-modules
Since commit
8b41fc4454e ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230308121230.5354-2-nick.alcock@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 10 Mar 2023 06:18:59 +0000 (22:18 -0800)]
Merge git://git./linux/kernel/git/netdev/net
Documentation/bpf/bpf_devel_QA.rst
b7abcd9c656b ("bpf, doc: Link to submitting-patches.rst for general patch submission info")
d56b0c461d19 ("bpf, docs: Fix link to netdev-FAQ target")
https://lore.kernel.org/all/
20230307095812.
236eb1be@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tirthendu Sarkar [Thu, 9 Mar 2023 18:56:15 +0000 (00:26 +0530)]
i40e: add support for XDP multi-buffer Rx
This patch adds multi-buffer support for the i40e_driver.
i40e_clean_rx_irq() is modified to collate all the buffers of a packet
before calling the XDP program. xdp_buff is built for the first frag of
the packet and subsequent frags are added to it. 'next_to_process' is
incremented for all non-EOP frags while 'next_to_clean' stays at the
first descriptor of the packet. XDP program is called only on receiving
EOP frag.
New functions are added for adding frags to xdp_buff and for post
processing of the buffers once the xdp prog has run. For XDP_PASS this
results in a skb with multiple fragments.
i40e_build_skb() builds the skb around xdp buffer that already contains
frags data. So i40e_add_rx_frag() helper function is now removed. Since
fields before 'dataref' in skb_shared_info are cleared during
napi_skb_build(), xdp_update_skb_shared_info() is called to set those.
For i40e_construct_skb(), all the frags data needs to be copied from
xdp_buffer's shared_skb_info to newly constructed skb's shared_skb_info.
This also means 'skb' does not need to be preserved across i40e_napi_poll()
calls and hence is removed from i40e_ring structure.
Previously i40e_alloc_rx_buffers() was called for every 32 cleaned
buffers. For multi-buffers this may not be optimal as there may be more
cleaned buffers in each i40e_clean_rx_irq() call. So this is now called
when at least half of the ring size has been cleaned.
Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tirthendu Sarkar [Thu, 9 Mar 2023 18:56:14 +0000 (00:26 +0530)]
i40e: add xdp_buff to i40e_ring struct
Store xdp_buff on Rx ring struct in preparation for XDP multi-buffer
support. This will allow us to combine fragmented frames across
separate NAPI cycles in the same way as currently skb fragments are
handled. This means that skb pointer on Rx ring will become redundant
and will be removed in a later patch. As a consequence i40e_trace() now
uses xdp instead of skb pointer.
Truesize only needs to be calculated for page sizes bigger than 4k as it
is always half-page for 4k pages. With xdp_buff on ring, frame size can
now be set during xdp_init_buff() and need not be repopulated in each
NAPI call for 4k pages. As a consequence i40e_rx_frame_truesize() is now
used only for bigger pages.
Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tirthendu Sarkar [Thu, 9 Mar 2023 18:56:13 +0000 (00:26 +0530)]
i40e: introduce next_to_process to i40e_ring
Add a new field called next_to_process in the i40e_ring that is
advanced for every buffer and change the semantics of next_to_clean to
point to the first buffer of a packet. Driver will use next_to_process
in the same way next_to_clean was used previously.
For the non multi-buffer case, next_to_process and next_to_clean will
always be the same since each packet consists of a single buffer.
Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tirthendu Sarkar [Thu, 9 Mar 2023 18:56:12 +0000 (00:26 +0530)]
i40e: use frame_sz instead of recalculating truesize for building skb
In skb path truesize is calculated while building skb. This is now
avoided and xdp->frame_is used instead for both i40e_build_skb() and
i40e_construct_skb().
Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tirthendu Sarkar [Thu, 9 Mar 2023 18:56:11 +0000 (00:26 +0530)]
i40e: Change size to truesize when using i40e_rx_buffer_flip()
Truesize is now passed directly to i40e_rx_buffer_flip() instead of size
so that it does not need to recalculate truesize from size using
i40e_rx_frame_truesize() before adjusting page offset.
With these change the function can now be used during skb building and
adding frags. In later patches it will also be easier for adjusting
page offsets for multi-buffers.
Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tirthendu Sarkar [Thu, 9 Mar 2023 18:56:10 +0000 (00:26 +0530)]
i40e: add pre-xdp page_count in rx_buffer
Page count of rx_buffer needs to be stored prior to XDP call to prevent
page recycling in case that buffer would be freed within xdp redirect
path. Instead of storing it on the stack, now it is stored in the
rx_buffer struct. This will help in processing multi-buffers as the page
counts of all rx_buffers (of the same packet) don't need to be stored on
stack.
Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tirthendu Sarkar [Thu, 9 Mar 2023 18:56:09 +0000 (00:26 +0530)]
i40e: change Rx buffer size for legacy-rx to support XDP multi-buffer
Adding support for XDP multi-buffer entails adding information of all
the fragments of the packet in the xdp_buff. This approach implies that
underlying buffer has to provide tailroom for skb_shared_info.
In the legacy-rx mode, driver can only configure up to 2k sized Rx buffers
and with the current configuration of 2k sized Rx buffers there is no way
to do tailroom reservation for skb_shared_info. Hence size of Rx buffers
is now lowered to 2048 - sizeof(skb_shared_info). Also, driver can only
chain up to 5 Rx buffers and this means max MTU supported for legacy-rx
is now 8614 (5 * rx_buffer_len - ETH header with VLAN).
Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tirthendu Sarkar [Thu, 9 Mar 2023 18:56:08 +0000 (00:26 +0530)]
i40e: consolidate maximum frame size calculation for vsi
Introduce new helper function to calculate max frame size for validating
and setting of vsi frame size. This is used while configuring vsi,
changing the MTU and attaching an XDP program to the vsi.
This is in preparation of the legacy rx and multi-buffer changes to be
introduced in later patches.
Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Linus Torvalds [Thu, 9 Mar 2023 18:56:58 +0000 (10:56 -0800)]
Merge tag 'net-6.3-rc2' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter and bpf.
Current release - regressions:
- core: avoid skb end_offset change in __skb_unclone_keeptruesize()
- sched:
- act_connmark: handle errno on tcf_idr_check_alloc
- flower: fix fl_change() error recovery path
- ieee802154: prevent user from crashing the host
Current release - new code bugs:
- eth: bnxt_en: fix the double free during device removal
- tools: ynl:
- fix enum-as-flags in the generic CLI
- fully inherit attrs in subsets
- re-license uniformly under GPL-2.0 or BSD-3-clause
Previous releases - regressions:
- core: use indirect calls helpers for sk_exit_memory_pressure()
- tls:
- fix return value for async crypto
- avoid hanging tasks on the tx_lock
- eth: ice: copy last block omitted in ice_get_module_eeprom()
Previous releases - always broken:
- core: avoid double iput when sock_alloc_file fails
- af_unix: fix struct pid leaks in OOB support
- tls:
- fix possible race condition
- fix device-offloaded sendpage straddling records
- bpf:
- sockmap: fix an infinite loop error
- test_run: fix &xdp_frame misplacement for LIVE_FRAMES
- fix resolving BTF_KIND_VAR after ARRAY, STRUCT, UNION, PTR
- netfilter: tproxy: fix deadlock due to missing BH disable
- phylib: get rid of unnecessary locking
- eth: bgmac: fix *initial* chip reset to support BCM5358
- eth: nfp: fix csum for ipsec offload
- eth: mtk_eth_soc: fix RX data corruption issue
Misc:
- usb: qmi_wwan: add telit 0x1080 composition"
* tag 'net-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (64 commits)
tools: ynl: fix enum-as-flags in the generic CLI
tools: ynl: move the enum classes to shared code
net: avoid double iput when sock_alloc_file fails
af_unix: fix struct pid leaks in OOB support
eth: fealnx: bring back this old driver
net: dsa: mt7530: permit port 5 to work without port 6 on MT7621 SoC
net: microchip: sparx5: fix deletion of existing DSCP mappings
octeontx2-af: Unlock contexts in the queue context cache in case of fault detection
net/smc: fix fallback failed while sendmsg with fastopen
ynl: re-license uniformly under GPL-2.0 OR BSD-3-Clause
mailmap: update entries for Stephen Hemminger
mailmap: add entry for Maxim Mikityanskiy
nfc: change order inside nfc_se_io error path
ethernet: ice: avoid gcc-9 integer overflow warning
ice: don't ignore return codes in VSI related code
ice: Fix DSCP PFC TLV creation
net: usb: qmi_wwan: add Telit 0x1080 composition
net: usb: cdc_mbim: avoid altsetting toggling for Telit FE990
netfilter: conntrack: adopt safer max chain length
net: tls: fix device-offloaded sendpage straddling records
...
Linus Torvalds [Thu, 9 Mar 2023 18:17:23 +0000 (10:17 -0800)]
Merge tag 'for-linus-
2023030901' of git://git./linux/kernel/git/hid/hid
Pull HID fixes from Benjamin Tissoires:
- fix potential out of bound write of zeroes in HID core with a
specially crafted uhid device (Lee Jones)
- fix potential use-after-free in work function in intel-ish-hid (Reka
Norman)
- selftests config fixes (Benjamin Tissoires)
- few device small fixes and support
* tag 'for-linus-
2023030901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: intel-ish-hid: ipc: Fix potential use-after-free in work function
HID: logitech-hidpp: Add support for Logitech MX Master 3S mouse
HID: cp2112: Fix driver not registering GPIO IRQ chip as threaded
selftest: hid: fix hid_bpf not set in config
HID: uhid: Over-ride the default maximum data buffer value with our own
HID: core: Provide new max_buffer_size attribute to over-ride the default
Linus Torvalds [Thu, 9 Mar 2023 18:08:46 +0000 (10:08 -0800)]
Merge tag 'm68k-for-v6.3-tag2' of git://git./linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
- Fix systems with memory at end of 32-bit address space
- Fix initrd on systems where memory does not start at address zero
- Fix 68030 handling of bus errors for addresses in exception tables
* tag 'm68k-for-v6.3-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Only force 030 bus error if PC not in exception table
m68k: mm: Move initrd phys_to_virt handling after paging_init()
m68k: mm: Fix systems with memory at end of 32-bit address space
Al Viro [Mon, 6 Mar 2023 01:20:30 +0000 (01:20 +0000)]
sh: sanitize the flags on sigreturn
We fetch %SR value from sigframe; it might have been modified by signal
handler, so we can't trust it with any bits that are not modifiable in
user mode.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Rich Felker <dalias@libc.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paolo Abeni [Thu, 9 Mar 2023 10:45:08 +0000 (11:45 +0100)]
Merge branch '100GbE' of git://git./linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-07 (ice)
This series contains updates to ice driver only.
Dave removes masking from pfcena field as it was incorrectly preventing
valid traffic classes from being enabled.
Michal resolves various smatch issues such as not propagating error
codes and returning 0 explicitly.
Arnd Bergmann resolves gcc-9 warning for integer overflow.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ethernet: ice: avoid gcc-9 integer overflow warning
ice: don't ignore return codes in VSI related code
ice: Fix DSCP PFC TLV creation
====================
Link: https://lore.kernel.org/r/20230307220714.3997294-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Abeni [Thu, 9 Mar 2023 10:31:46 +0000 (11:31 +0100)]
Merge branch 'sctp-add-another-two-stream-schedulers'
Xin Long says:
====================
sctp: add another two stream schedulers
All SCTP stream schedulers are defined in rfc8260#section-3,
First-Come First-Served, Round-Robin and Priority-Based
Schedulers are already added in kernel.
This patchset adds another two schedulers: Fair Capacity
Scheduler and Weighted Fair Queueing Scheduler.
Note that the left one "Round-Robin Scheduler per Packet"
Scheduler is not implemented by this patch, as it's still
intrusive to be added in the current SCTP kernel code.
====================
Link: https://lore.kernel.org/r/cover.1678224012.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Xin Long [Tue, 7 Mar 2023 21:23:27 +0000 (16:23 -0500)]
sctp: add weighted fair queueing stream scheduler
As it says in rfc8260#section-3.6 about the weighted fair queueing
scheduler:
A Weighted Fair Queueing scheduler between the streams is used. The
weight is configurable per outgoing SCTP stream. This scheduler
considers the lengths of the messages of each stream and schedules
them in a specific way to use the capacity according to the given
weights. If the weight of stream S1 is n times the weight of stream
S2, the scheduler should assign to stream S1 n times the capacity it
assigns to stream S2. The details are implementation dependent.
Interleaving user messages allows for a better realization of the
capacity usage according to the given weights.
This patch adds Weighted Fair Queueing Scheduler actually based on
the code of Fair Capacity Scheduler by adding fc_weight into struct
sctp_stream_out_ext and taking it into account when sorting stream->
fc_list in sctp_sched_fc_sched() and sctp_sched_fc_dequeue_done().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Xin Long [Tue, 7 Mar 2023 21:23:26 +0000 (16:23 -0500)]
sctp: add fair capacity stream scheduler
As it says in rfc8260#section-3.5 about the fair capacity scheduler:
A fair capacity distribution between the streams is used. This
scheduler considers the lengths of the messages of each stream and
schedules them in a specific way to maintain an equal capacity for
all streams. The details are implementation dependent. interleaving
user messages allows for a better realization of the fair capacity
usage.
This patch adds Fair Capacity Scheduler based on the foundations added
by commit
5bbbbe32a431 ("sctp: introduce stream scheduler foundations"):
A fc_list and a fc_length are added into struct sctp_stream_out_ext and
a fc_list is added into struct sctp_stream. In .enqueue, when there are
chunks enqueued into a stream, this stream will be linked into stream->
fc_list by its fc_list ordered by its fc_length. In .dequeue, it always
picks up the 1st skb from stream->fc_list. In .dequeue_done, fc_length
is increased by chunk's len and update its location in stream->fc_list
according to the its new fc_length.
Note that when the new fc_length overflows in .dequeue_done, instead of
resetting all fc_lengths to 0, we only reduced them by U32_MAX / 4 to
avoid a moment of imbalance in the scheduling, as Marcelo suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Abeni [Thu, 9 Mar 2023 08:51:34 +0000 (09:51 +0100)]
Merge branch 'various-mtk_eth_soc-cleanups'
Russell King says:
====================
Various mtk_eth_soc cleanups
Here are a number of patches that do a bit of cleanup to mtk_eth_soc.
The first patch cleans up mtk_gmac0_rgmii_adjust(), which is the
troublesome function preventing the driver becoming a post-March2020
phylink driver. It doesn't solve that problem, merely makes the code
easier to follow by getting rid of repeated tenary operators.
The second patch moves the check for DDR2 memory to the initialisation
of phylink's supported_interfaces - if TRGMII is not possible for some
reason, we should not be erroring out in phylink MAC operations when
that can be determined prior to phylink creation.
The third patch removes checks from mtk_mac_config() that are done
when initialising supported_interfaces - phylink will not call
mtk_mac_config() with an interface that was not marked as supported,
so these checks are redundant.
The last patch removes the remaining vestiges of REVMII and RMII
support, which appears to be entirely unused.
These shouldn't conflict with Daniel's patch set, but if they do I
will rework as appropriate.
====================
Link: https://lore.kernel.org/r/ZAdj9qUXcHUsK7Gt@shell.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Russell King (Oracle) [Tue, 7 Mar 2023 16:19:41 +0000 (16:19 +0000)]
net: mtk_eth_soc: remove support for RMII and REVMII modes
Since the conversion of mtk_eth_soc to phylink's supported_interfaces
bitmap, these two modes have not been selectable. No one has raised
this as an issue. Checking the in-kernel DT files, none of them use
either of these modes with this hardware.
Daniel Golle concurs:
A quick grep through the device trees of the more than 650 ramips and
mediatek boards we support in OpenWrt has revealed that *none* of them
uses either reduced-MII or reverse-MII PHY modes. I could imaging that
some more specialized ramips boards may use the RMII 100M PHY mode to
connect with exotic PHYs for industrial or automotive applications
(think: for 100BASE-T1 PHY connected via RMII). I have never seen or
touched such boards, but there are hints that they do exist.
For reverse-MII there are cases in which the Ralink SoC (Rt305x, for
example) is used in iNIC mode, ie. connected as a PHY to another SoC,
and running only a minimal firmware rather than running Linux. Due to
the lack of external DRAM for the Ralink SoC on this kind of boards,
the Ralink SoC there will anyway never be able to boot Linux.
I've seen this e.g. in multimedia devices like early WiFi-connected
not-yet-so-smart TVs.
Consequently, the conclusion is that no one uses these modes with this
hardware, so we might as well drop support for them.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Russell King (Oracle) [Tue, 7 Mar 2023 16:19:36 +0000 (16:19 +0000)]
net: mtk_eth_soc: remove unnecessary checks in mtk_mac_config()
mtk_mac_config() checks that the interface mode is permitted for the
capabilities, but we already do these checks in mtk_add_mac() when
initialising phylink's supported_interfaces bitmap. Remove the
unnecessary tests.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Russell King (Oracle) [Tue, 7 Mar 2023 16:19:31 +0000 (16:19 +0000)]
net: mtk_eth_soc: move trgmii ddr2 check to probe function
If TRGMII mode is not permitted when using DDR2 mode, we should handle
that when setting up phylink's ->supported_interfaces so phylink knows
that this is not supported by the hardware. Move this check to
mtk_add_mac().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Russell King (Oracle) [Tue, 7 Mar 2023 16:19:26 +0000 (16:19 +0000)]
net: mtk_eth_soc: tidy mtk_gmac0_rgmii_adjust()
Get rid of the multiple tenary operators in mtk_gmac0_rgmii_adjust()
replacing them with a single if(), thus making the code easier to read.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Thu, 9 Mar 2023 07:34:42 +0000 (23:34 -0800)]
Merge branch 'pci-aer-remove-redundant-device-control-error-reporting-enable'
Bjorn Helgaas says:
====================
PCI/AER: Remove redundant Device Control Error Reporting Enable
From: Bjorn Helgaas <bhelgaas@google.com>
Since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is native"),
which appeared in v6.0, the PCI core has enabled PCIe error reporting for
all devices during enumeration.
Remove driver code to do this and remove unnecessary includes of
<linux/aer.h> from several other drivers.
Intel folks, sorry that I missed removing the <linux/aer.h> includes in the
first series.
====================
Link: https://lore.kernel.org/r/20230307181940.868828-1-helgaas@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:39 +0000 (12:19 -0600)]
ixgbe: Remove unnecessary aer.h include
<linux/aer.h> is unused, so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:38 +0000 (12:19 -0600)]
igc: Remove unnecessary aer.h include
<linux/aer.h> is unused, so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:37 +0000 (12:19 -0600)]
igb: Remove unnecessary aer.h include
<linux/aer.h> is unused, so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:36 +0000 (12:19 -0600)]
ice: Remove unnecessary aer.h include
<linux/aer.h> is unused, so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:35 +0000 (12:19 -0600)]
iavf: Remove unnecessary aer.h include
<linux/aer.h> is unused, so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:34 +0000 (12:19 -0600)]
i40e: Remove unnecessary aer.h include
<linux/aer.h> is unused, so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:33 +0000 (12:19 -0600)]
fm10k: Remove unnecessary aer.h include
<linux/aer.h> is unused, so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:32 +0000 (12:19 -0600)]
e1000e: Remove unnecessary aer.h include
<linux/aer.h> is unused, so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:31 +0000 (12:19 -0600)]
net: txgbe: Drop redundant pci_enable_pcie_error_reporting()
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiawen Wu <jiawenwu@trustnetic.com>
Cc: Mengyuan Lou <mengyuanlou@net-swift.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:30 +0000 (12:19 -0600)]
net: ngbe: Drop redundant pci_enable_pcie_error_reporting()
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiawen Wu <jiawenwu@trustnetic.com>
Cc: Mengyuan Lou <mengyuanlou@net-swift.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:29 +0000 (12:19 -0600)]
sfc_ef100: Drop redundant pci_disable_pcie_error_reporting()
51b35a454efd ("sfc: skeleton EF100 PF driver") added a call to
pci_disable_pcie_error_reporting() in ef100_pci_remove().
Remove this call since there's no apparent reason to disable error
reporting when it was not previously enabled.
Note that since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core enables PCIe error reporting for all devices during
enumeration, so the driver doesn't need to do it itself.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:28 +0000 (12:19 -0600)]
sfc/siena: Drop redundant pci_enable_pcie_error_reporting()
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:27 +0000 (12:19 -0600)]
sfc: falcon: Drop redundant pci_enable_pcie_error_reporting()
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:26 +0000 (12:19 -0600)]
sfc: Drop redundant pci_enable_pcie_error_reporting()
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:25 +0000 (12:19 -0600)]
qlcnic: Remove unnecessary aer.h include
<linux/aer.h> is unused, so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shahed Shaikh <shshaikh@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:24 +0000 (12:19 -0600)]
qlcnic: Drop redundant pci_enable_pcie_error_reporting()
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shahed Shaikh <shshaikh@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:23 +0000 (12:19 -0600)]
net: qede: Remove unnecessary aer.h include
<linux/aer.h> is unused, so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ariel Elior <aelior@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:22 +0000 (12:19 -0600)]
qed: Drop redundant pci_enable_pcie_error_reporting()
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ariel Elior <aelior@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:21 +0000 (12:19 -0600)]
octeon_ep: Drop redundant pci_enable_pcie_error_reporting()
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Veerasenareddy Burru <vburru@marvell.com>
Cc: Abhijit Ayarekar <aayarekar@marvell.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:20 +0000 (12:19 -0600)]
netxen_nic: Drop redundant pci_enable_pcie_error_reporting()
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Also note that the driver only called these for NX_IS_REVISION_P3 devices,
so since
f26e58bf6f54, error reporting has been enabled for devices other
than NX_IS_REVISION_P3.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Manish Chopra <manishc@marvell.com>
Cc: Rahul Verma <rahulv@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:19 +0000 (12:19 -0600)]
net: hns3: remove unnecessary aer.h include
<linux/aer.h> is unused, so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:18 +0000 (12:19 -0600)]
net/fungible: Drop redundant pci_enable_pcie_error_reporting()
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Dimitris Michailidis <dmichail@fungible.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:17 +0000 (12:19 -0600)]
cxgb4: Drop redundant pci_enable_pcie_error_reporting()
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Raju Rangoju <rajur@chelsio.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:16 +0000 (12:19 -0600)]
bnxt: Drop redundant pci_enable_pcie_error_reporting()
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:15 +0000 (12:19 -0600)]
bnx2x: Drop redundant pci_enable_pcie_error_reporting()
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjorn Helgaas [Tue, 7 Mar 2023 18:19:14 +0000 (12:19 -0600)]
bnx2: Drop redundant pci_enable_pcie_error_reporting()
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since
f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
cd709aa90648 ("bnx2: Add PCI Advanced Error Reporting support.") added
pci_enable_pcie_error_reporting() for all devices, and
c239f279e571 ("bnx2:
Enable AER on PCIE devices only") restricted it to BNX2_CHIP_5709 devices
to avoid an error message when it failed on non-PCIe devices. The PCI core
only enables PCIe error reporting on PCIe devices, which I assume means
BNX2_CHIP_5709.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rasesh Mody <rmody@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>