OSDN Git Service
Michael Walle [Wed, 6 May 2020 14:53:14 +0000 (16:53 +0200)]
net: phy: bcm54140: use phy_package_shared
Use the new phy_package_shared common storage to ease the package
initialization and to access the global registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Walle [Wed, 6 May 2020 14:53:13 +0000 (16:53 +0200)]
net: phy: add concept of shared storage for PHYs
There are packages which contain multiple PHY devices, eg. a quad PHY
transceiver. Provide functions to allocate and free shared storage.
Usually, a quad PHY contains global registers, which don't belong to any
PHY. Provide convenience functions to access these registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ayush Sawal [Wed, 6 May 2020 14:47:19 +0000 (20:17 +0530)]
Revert "crypto: chelsio - Inline single pdu only"
This reverts commit
27c6feb0fb33a665a746346e76714826a5be5d10.
For ipsec offload the chelsio's ethernet driver expects a single mtu
sized packet.
But when ipsec traffic is running using iperf, most of the packets in
that traffic are gso packets(large sized skbs) because GSO is enabled by
default in TCP, due to this commit
0a6b2a1dc2a2 ("tcp: switch to GSO
being always on"), so chcr_ipsec_offload_ok() receives a gso
skb(with gso_size non zero).
Due to the check in chcr_ipsec_offload_ok(), this function returns false
for most of the packet, then ipsec offload is skipped and the skb goes
out taking the coprocessor path which reduces the bandwidth for inline
ipsec.
If this check is removed then for most of the packets(large sized skbs)
the chcr_ipsec_offload_ok() returns true and then as GSO is on, the
segmentation of the packet happens in the kernel and then finally the
driver_xmit is called, which receives a segmented mtu sized packet which
is what the driver expects for ipsec offload. So this case becomes
unnecessary here, therefore removing it.
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunjian Wang [Wed, 6 May 2020 12:55:52 +0000 (20:55 +0800)]
net: 7990: Fix use correct return type for ndo_start_xmit()
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunjian Wang [Wed, 6 May 2020 12:21:45 +0000 (20:21 +0800)]
net: cpmac: Fix use correct return type for ndo_start_xmit()
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunjian Wang [Wed, 6 May 2020 12:10:28 +0000 (20:10 +0800)]
net: moxa: Fix use correct return type for ndo_start_xmit()
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunjian Wang [Wed, 6 May 2020 11:38:46 +0000 (19:38 +0800)]
net: lantiq: Fix use correct return type for ndo_start_xmit()
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ChenTao [Wed, 6 May 2020 11:22:17 +0000 (19:22 +0800)]
net: enetc: Make some symbols static
Fix the following warning:
drivers/net/ethernet/freescale/enetc/enetc_qos.c:427:20: warning:
symbol 'enetc_act_fwd' was not declared. Should it be static?
drivers/net/ethernet/freescale/enetc/enetc_qos.c:966:20: warning:
symbol 'enetc_check_flow_actions' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ChenTao <chentao107@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunjian Wang [Wed, 6 May 2020 11:13:08 +0000 (19:13 +0800)]
net: mediatek: Fix use correct return type for ndo_start_xmit()
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunjian Wang [Wed, 6 May 2020 11:04:59 +0000 (19:04 +0800)]
net: socionext: Fix use correct return type for ndo_start_xmit()
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunjian Wang [Wed, 6 May 2020 09:25:14 +0000 (17:25 +0800)]
net: renesas: Fix use correct return type for ndo_start_xmit()
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 6 May 2020 21:11:26 +0000 (14:11 -0700)]
Merge branch 's390-qeth-next'
Julian Wiedmann says:
====================
s390/qeth: updates 2020-05-06
please apply the following patch series for qeth to netdev's net-next
tree.
Same patches as yesterday, except that the ethtool reset has been
dropped for now.
This primarily adds infrastructure to deal with HW offloads when the
packets get forwarded over the adapter's internal switch.
Aside from that, just some minor tweaking for the TX code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 6 May 2020 08:09:49 +0000 (10:09 +0200)]
s390/qeth: clean up Kconfig help text
Remove a stale doc link. While at it also reword the help text to get
rid of an outdated marketing term.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 6 May 2020 08:09:48 +0000 (10:09 +0200)]
s390/qeth: return error when starting a reset fails
When starting the reset worker via sysfs is unsuccessful, return an
error to the user.
Modernize the sysfs input parsing while at it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 6 May 2020 08:09:47 +0000 (10:09 +0200)]
s390/qeth: set TX IRQ marker on last buffer in a group
When qeth_flush_buffers() gets called for a group of TX buffers
(currently up to 2 for OSA-style devices), the code iterates over each
buffer for some final processing.
During this processing, it sets the TX IRQ marker on the leading buffer
rather than the last one. This can result in delayed TX completion of
the trailing buffers. So pull the IRQ marker code out of the loop, and
apply it to the final buffer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 6 May 2020 08:09:46 +0000 (10:09 +0200)]
s390/qeth: indicate contiguous TX buffer elements
The TX path usually maps the full content of a page into a buffer
element. But there's specific skb layouts (ie. linearized TSO skbs)
where the HW header (1) requires a separate buffer element, and (2) is
page-contiguous with the packet data that's mapped into the next buffer
element.
Flag such buffer elements accordingly, so that HW can optimize its data
access for them.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 6 May 2020 08:09:45 +0000 (10:09 +0200)]
s390/qeth: merge TX skb mapping code
Merge the __qeth_fill_buffer() helper into its only caller. This way all
mapping-related context is in one place, and we can make some more use
of it in a subsequent patch.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 6 May 2020 08:09:44 +0000 (10:09 +0200)]
s390/qeth: don't use restricted offloads for local traffic
Current OSA models don't support TSO for traffic to local next-hops, and
some old models didn't offer TX CSO for such packets either.
So as part of .ndo_features_check, check if a packet's next-hop resides
on the same OSA Adapter. Opt out from affected HW offloads accordingly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 6 May 2020 08:09:43 +0000 (10:09 +0200)]
s390/qeth: extract helpers for next-hop lookup
These will be used in a subsequent patch.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 6 May 2020 08:09:42 +0000 (10:09 +0200)]
s390/qeth: add debugfs file for local IP addresses
For debugging purposes, provide read access to the local_addr caches
via debug/qeth/<dev_name>/local_addrs.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 6 May 2020 08:09:41 +0000 (10:09 +0200)]
s390/qeth: process local address events
In configurations where specific HW offloads are in use, OSA adapters
will raise notifications to their virtual devices about the IP addresses
that currently reside on the same adapter.
Cache these addresses in two RCU-enabled hash tables, and flush the
tables once the relevant HW offload(s) get disabled.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 6 May 2020 08:09:40 +0000 (10:09 +0200)]
s390/qeth: keep track of LP2LP capability for csum offload
When enabling TX CSO, make a note of whether the device has support for
LP2LP offloading. This will become relevant in subsequent patches.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Samuel Zou [Wed, 6 May 2020 06:27:30 +0000 (14:27 +0800)]
net: ethernet: mediatek: Make mtk_m32 static
Fix the following sparse warning:
drivers/net/ethernet/mediatek/mtk_eth_soc.c:68:5: warning:
symbol 'mtk_m32' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Yan [Wed, 6 May 2020 06:16:30 +0000 (14:16 +0800)]
net: mlx4: remove unneeded variable "err" in mlx4_en_get_rxfh()
Fix the following coccicheck warning:
drivers/net/ethernet/mellanox/mlx4/en_ethtool.c:1238:5-8: Unneeded
variable: "err". Return "0" on line 1252
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Yan [Wed, 6 May 2020 06:16:16 +0000 (14:16 +0800)]
net: bridge: return false in br_mrp_enabled()
Fix the following coccicheck warning:
net/bridge/br_private.h:1334:8-9: WARNING: return of 0/1 in function
'br_mrp_enabled' with return type bool
Fixes:
6536993371fab ("bridge: mrp: Integrate MRP into the bridge")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunjian Wang [Wed, 6 May 2020 06:10:41 +0000 (14:10 +0800)]
net: cortina: Fix use correct return type for ndo_start_xmit()
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Samuel Zou [Wed, 6 May 2020 02:54:58 +0000 (10:54 +0800)]
net: ethernet: ti: Use PTR_ERR_OR_ZERO() to simplify code
Fixes coccicheck warning:
drivers/net/ethernet/ti/am65-cpts.c:1017:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Tue, 5 May 2020 16:21:23 +0000 (19:21 +0300)]
net: ethernet: ti: am65-cpts: fix build
It's possible to have build configuration which will force PTP_1588_CLOCK=m
and so TI_K3_AM65_CPTS=m while still have TI_K3_AM65_CPSW_NUSS=y. This will
cause build failures:
aarch64-linux-gnu-ld: ../drivers/net/ethernet/ti/am65-cpsw-nuss.o: in function `am65_cpsw_init_cpts':
../drivers/net/ethernet/ti/am65-cpsw-nuss.c:1685: undefined reference to `am65_cpts_create'
aarch64-linux-gnu-ld: ../drivers/net/ethernet/ti/am65-cpsw-nuss.c:1685:(.text+0x2e20):
relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `am65_cpts_create'
Fix it by adding dependencies from CPTS in TI_K3_AM65_CPSW_NUSS as below:
config TI_K3_AM65_CPSW_NUSS
...
depends on TI_K3_AM65_CPTS || !TI_K3_AM65_CPTS
Note. This will create below dependencies and for NFS boot + CPTS all of them
have to be built-in.
PTP_1588_CLOCK -> TI_K3_AM65_CPTS -> TI_K3_AM65_CPSW_NUSS
While here, clean up TI_K3_AM65_CPTS definition.
Fixes:
b1f66a5bee07 ("net: ethernet: ti: am65-cpsw-nuss: enable packet timestamping support")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
William Tu [Tue, 5 May 2020 16:05:06 +0000 (09:05 -0700)]
erspan: Add type I version 0 support.
The Type I ERSPAN frame format is based on the barebones
IP + GRE(4-byte) encapsulation on top of the raw mirrored frame.
Both type I and II use 0x88BE as protocol type. Unlike type II
and III, no sequence number or key is required.
To creat a type I erspan tunnel device:
$ ip link add dev erspan11 type erspan \
local 172.16.1.100 remote 172.16.1.200 \
erspan_ver 0
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Tue, 5 May 2020 13:34:00 +0000 (15:34 +0200)]
cxgb4/cxgb4vf: Remove superfluous void * cast in debugfs_create_file() call
There is no need to cast a typed pointer to a void pointer when calling
a function that accepts the latter. Remove it, as the cast prevents
further compiler checks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 May 2020 19:56:52 +0000 (12:56 -0700)]
Merge branch 'smc-log-state-changes-and-cleanup'
Karsten Graul says:
====================
smc: log state changes and cleanup
Patch 1 adds the logging of important state changes to enable SMC-R
users to detect SMC-R link groups that are not redundant and require
user actions. Patch 2 is a contribution to clean up an unused inline
function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Tue, 5 May 2020 13:01:21 +0000 (15:01 +0200)]
net/smc: remove unused inline function smc_curs_read
commit
bac6de7b6370 ("net/smc: eliminate cursor read and write calls")
left behind this.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Tue, 5 May 2020 13:01:20 +0000 (15:01 +0200)]
net/smc: log important pnetid and state change events
Print to system log when SMC links are available or go down, link group
state changes or pnetids are applied to and removed from devices.
The log entries are triggered by either user configuration actions or
adapter activation/deactivation events and are not expected to happen
often. The entries help SMC users to keep track of the SMC link group
status and to detect when actions are needed (like to add replacements
for failed adapters).
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Tue, 5 May 2020 10:19:35 +0000 (13:19 +0300)]
dt-binding: net: ti: am65x-cpts: fix dt_binding_check fail
Fix dt_binding_check fail:
Fix Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml: $id: relative path/filename doesn't match actual path or filename
expected: http://devicetree.org/schemas/net/ti,k3-am654-cpts.yaml#
Unknown file referenced: [Errno 2] No such file or directory: '/usr/local/lib/python3.6/dist-packages/dtschema/schemas/net/ti,am654-cpts.yaml'
Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml: $id: relative path/filename doesn't match actual path or filename
expected: http://devicetree.org/schemas/net/ti,k3-am654-cpts.yaml#
Unknown file referenced: [Errno 2] No such file or directory: '/usr/local/lib/python3.6/dist-packages/dtschema/schemas/net/ti,am654-cpts.yaml'
Cc: Rob Herring <robh@kernel.org>
Fixes:
6e87ac748e94 ("dt-binding: ti: am65x: document common platform time sync cpts module")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Tue, 5 May 2020 10:03:07 +0000 (10:03 +0000)]
net: ipa: remove duplicated include from ipa_mem.c
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 May 2020 19:08:02 +0000 (12:08 -0700)]
sch_choke: Remove classid from choke_skb_cb.
Suggested by Cong Wang.
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Tue, 5 May 2020 08:51:24 +0000 (16:51 +0800)]
net: sierra_net: Remove unused inline function
There's no callers in-tree
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Tue, 5 May 2020 08:50:09 +0000 (16:50 +0800)]
bnx2x: Remove unused inline function bnx2x_vf_vlan_credit
commit
05cc5a39ddb7 ("bnx2x: add vlan filtering offload")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Tue, 5 May 2020 08:47:36 +0000 (16:47 +0800)]
net: sched: choke: Remove unused inline function choke_set_classid
There's no callers in-tree anymore since commit
5952fde10c35 ("net:
sched: choke: remove dead filter classify code")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Tue, 5 May 2020 08:44:21 +0000 (16:44 +0800)]
net: microchip: Remove unused inline function is_bits_set
There's no callers in-tree.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Tue, 5 May 2020 08:43:39 +0000 (16:43 +0800)]
myri10ge: Remove unused inline function myri10ge_vlan_ip_csum
commit
4ca3221fe4b6 ("myri10ge: Convert from LRO to GRO")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Tue, 5 May 2020 08:42:56 +0000 (16:42 +0800)]
net: stmmac: Remove unused inline function stmmac_rx_threshold_count
There's no caller in-tree since
commit
2af6106ae949 ("net: stmmac: Introducing support for Page Pool")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Tue, 5 May 2020 08:40:37 +0000 (16:40 +0800)]
net: mv643xx_eth: Remove unused inline function sum16_as_be
commit
84411f73b884 ("net: mv643xx_eth: Avoid setting the initial TCP checksum")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Tue, 5 May 2020 08:33:12 +0000 (16:33 +0800)]
net: sun: cassini: Remove unused inline functions
There's no callers in-tree anymore.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Tue, 5 May 2020 08:31:56 +0000 (16:31 +0800)]
net: tehuti: remove unused inline function bdx_tx_db_size
There's no callers in-tree anymore.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunjian Wang [Tue, 5 May 2020 07:59:26 +0000 (15:59 +0800)]
net: ni: Fix use correct return type for ndo_start_xmit()
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Yan [Tue, 5 May 2020 07:46:23 +0000 (15:46 +0800)]
net: ethernet: ti: use true, false for bool variables in cpsw_new.c
Fix the following coccicheck warning:
drivers/net/ethernet/ti/cpsw_new.c:1924:2-17: WARNING: Assignment of
0/1 to bool variable
drivers/net/ethernet/ti/cpsw_new.c:1231:1-16: WARNING: Assignment of
0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Yan [Tue, 5 May 2020 07:46:08 +0000 (15:46 +0800)]
net: bnxt: Remove Comparison to bool in bnxt_ethtool.c
Fix the following coccicheck warning:
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:1991:5-46: WARNING:
Comparison to bool
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:1993:10-54: WARNING:
Comparison to bool
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2380:5-38: WARNING:
Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Yan [Tue, 5 May 2020 07:45:56 +0000 (15:45 +0800)]
net: agere: use true,false for bool variable
Fix the following coccicheck warning:
drivers/net/ethernet/agere/et131x.c:717:3-22: WARNING: Assignment of
0/1 to bool variable
drivers/net/ethernet/agere/et131x.c:721:1-20: WARNING: Assignment of
0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Yan [Tue, 5 May 2020 07:45:46 +0000 (15:45 +0800)]
net: atheros: remove conversion to bool in atl1c_start_mac()
No need to convert '==' expression to bool. This fixes the following
coccicheck warning:
drivers/net/ethernet/atheros/atl1c/atl1c_main.c:1189:63-68: WARNING:
conversion to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Yan [Tue, 5 May 2020 07:45:39 +0000 (15:45 +0800)]
net: qede: Use true for bool variable in qede_init_fp()
Fix the following coccicheck warning:
drivers/net/ethernet/qlogic/qede/qede_main.c:1717:5-19: WARNING:
Assignment of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Yan [Tue, 5 May 2020 07:44:00 +0000 (15:44 +0800)]
bnx2x: Remove Comparison to bool in bnx2x_dcb.c
Fix the following coccicheck warning:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_dcb.c:1548:17-31: WARNING:
Comparison to bool
drivers/net/ethernet/broadcom/bnx2x/bnx2x_dcb.c:1148:16-24: WARNING:
Comparison to bool
drivers/net/ethernet/broadcom/bnx2x/bnx2x_dcb.c:1158:30-38: WARNING:
Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Yan [Tue, 5 May 2020 07:43:49 +0000 (15:43 +0800)]
qlcnic: use true,false for bool variable in qlcnic_sriov_common.c
Fix the following coccicheck warning:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c:1585:3-25:
WARNING: Assignment of 0/1 to bool variable
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c:1588:3-25:
WARNING: Assignment of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunjian Wang [Tue, 5 May 2020 05:57:49 +0000 (13:57 +0800)]
net: emac: Fix use correct return type for ndo_start_xmit()
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunjian Wang [Tue, 5 May 2020 03:22:20 +0000 (11:22 +0800)]
net: nxp: Fix use correct return type for ndo_start_xmit()
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunjian Wang [Tue, 5 May 2020 03:06:45 +0000 (11:06 +0800)]
net: altera: Fix use correct return type for ndo_start_xmit()
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunjian Wang [Tue, 5 May 2020 02:49:20 +0000 (10:49 +0800)]
net: allwinner: Fix use correct return type for ndo_start_xmit()
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type. And emac_start_xmit() can
leak one skb if 'channel' == 3.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 May 2020 19:05:56 +0000 (12:05 -0700)]
Merge branch 'net-reduce-dynamic-lockdep-keys'
Cong Wang says:
====================
net: reduce dynamic lockdep keys
syzbot has been complaining about low MAX_LOCKDEP_KEYS for a
long time, it is mostly because we register 4 dynamic keys per
network device.
This patchset reduces the number of dynamic lockdep keys from
4 to 1 per netdev, by reverting to the previous static keys,
except for addr_list_lock which still has to be dynamic.
The second patch removes a bonding-specific key by the way.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sun, 3 May 2020 05:22:20 +0000 (22:22 -0700)]
bonding: remove useless stats_lock_key
After commit
b3e80d44f5b1
("bonding: fix lockdep warning in bond_get_stats()") the dynamic
key is no longer necessary, as we compute nest level at run-time.
So, we can just remove it to save some lockdep key entries.
Test commands:
ip link add bond0 type bond
ip link add bond1 type bond
ip link set bond0 master bond1
ip link set bond0 nomaster
ip link set bond1 master bond0
Reported-and-tested-by: syzbot+aaa6fa4949cc5d9b7b25@syzkaller.appspotmail.com
Cc: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sun, 3 May 2020 05:22:19 +0000 (22:22 -0700)]
net: partially revert dynamic lockdep key changes
This patch reverts the folowing commits:
commit
064ff66e2bef84f1153087612032b5b9eab005bd
"bonding: add missing netdev_update_lockdep_key()"
commit
53d374979ef147ab51f5d632dfe20b14aebeccd0
"net: avoid updating qdisc_xmit_lock_key in netdev_update_lockdep_key()"
commit
1f26c0d3d24125992ab0026b0dab16c08df947c7
"net: fix kernel-doc warning in <linux/netdevice.h>"
commit
ab92d68fc22f9afab480153bd82a20f6e2533769
"net: core: add generic lockdep keys"
but keeps the addr_list_lock_key because we still lock
addr_list_lock nestedly on stack devices, unlikely xmit_lock
this is safe because we don't take addr_list_lock on any fast
path.
Reported-and-tested-by: syzbot+aaa6fa4949cc5d9b7b25@syzkaller.appspotmail.com
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 May 2020 19:02:03 +0000 (12:02 -0700)]
Merge branch 'net-ethernet-ti-k3-introduce-common-platform-time-sync-driver-cpts'
Grygorii Strashko says:
====================
net: ethernet: ti: k3: introduce common platform time sync driver - cpts
This series introduced support for significantly upgraded TI A65x/J721E Common
platform time sync (CPTS) modules which are part of AM65xx Time Synchronization
Architecture [1].
The TI A65x/J721E now contain more than one CPTS instance:
- MCU CPSW CPTS (IEEE 1588 compliant)
- Main NAVSS CPTS (central)
- PCIe CPTS(s) (PTM compliant)
- J721E: Main CPSW9g CPTS (IEEE 1588 compliant)
which can work as separately as interact to each other through Time Sync Router
(TSR) and Compare Event Router (CER). In addition there are also ICSS-G IEP
blocks which can perform similar timsync functions, but require FW support.
More info also available in TRM [2][3]. Not all above modules are available
to the Linux by as of now as some of them are reserved for RTOS/FW purposes.
The scope of this submission is TI A65x/J721E CPSW CPTS and Main NAVSS CPTS,
and TSR was used for testing purposes.
+---------------------------+
| MCU CPSW |
+-------------------+ +------------------------+ | TS |
| Main Navss CPTS | | Time Sync Router (TSR) | | +-------------+ |
| | | | | | | |
| HW1_TS +<----------+ | | +--------v-----+ +--+--+
| | | | | | CPTS | |Port |
| ... | | | X+-->HW1_TS | | |
| HW8_TS <------------<---------+ | X|-->HW2_TS | +--^--+
| | | | +--------------->HW3_TS | | |
| | | | +--------------->HW4_TS | | |
| | | | | | | | | |
| | | | | | | | | |
| Genf0 +-----------> (A)---------+ +<--------------+Genf0 | | |
| | | | | | | | | |
| ... | | +-----------> <---------------+Genf1 ESTf+-------+ |
| | | | | | | |
| | | | | +--------------+ |
| Genf8 +---------->+ | | |
| | | SYNC0 ... SYNC3 | | |
+-------------------+ +------+------------+----+ +---------------------------+
+ +
X X
(A) shows possible routing path for MCU CPSW CPTS Genf0 signal as an example.
Main features of the new TI A65x/J721E CPTS modules are:
- 64-bit timestamp/counter mode support in ns by using add_val
- implemented in HW PPM and nudge adjustment.
- control of time sync events via interrupt or polling
- selection of multiple external reference clock sources
- hardware timestamp of ext. inputs events (HWx_TS_PUSH)
- periodic generator function outputs (TS_GENFx)
- (CPSW only) Ethernet Enhanced Scheduled Traffic Operations (CPTS_ESTFn),
which drives TSN schedule
- timestamping of all RX packets bypassing CPTS FIFO
Patch 1 - DT bindings
Patch 2 - the AM65x/J721E driver
Patch 3 - enables packet timestamping support in TI AM65x/J721E MCU CPSW driver.
Patches 4-7 - DT updates.
=== PTP Testing:
phc2sys -s CLOCK_REALTIME -c eth0 -m -O 0 -u30
phc2sys[627.331]: eth0 rms
409912446712787392 max
1587584079521858304 freq -6665 +/- 35040 delay 832 +/- 27
phc2sys[657.335]: eth0 rms 33 max 66 freq -0 +/- 28 delay 820 +/- 30
phc2sys[687.339]: eth0 rms 37 max 70 freq -1 +/- 32 delay 830 +/- 29
phc2sys[717.343]: eth0 rms 33 max 71 freq -0 +/- 29 delay 828 +/- 23
phc2sys[747.346]: eth0 rms 35 max 75 freq -0 +/- 31 delay 829 +/- 26
phc2sys[777.350]: eth0 rms 37 max 68 freq -1 +/- 32 delay 825 +/- 25
phc2sys[807.354]: eth0 rms 28 max 57 freq -1 +/- 25 delay 824 +/- 21
phc2sys[837.358]: eth0 rms 43 max 81 freq -1 +/- 37 delay 836 +/- 23
phc2sys[867.361]: eth0 rms 33 max 74 freq +0 +/- 29 delay 828 +/- 24
phc2sys[897.365]: eth0 rms 35 max 77 freq -2 +/- 30 delay 824 +/- 25
phc2sys[927.369]: eth0 rms 28 max 50 freq +0 +/- 25 delay 825 +/- 25
ptp4l -P -2 -H -i eth0 -l 6 -m -q -p /dev/ptp1 -f ptp.cfg -s
ptp4l[22095.754]: port 1: MASTER to UNCALIBRATED on RS_SLAVE
ptp4l[22097.754]: port 1: UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[22159.757]: rms 317 max 1418 freq +79 +/- 186 delay 410 +/- 1
ptp4l[22223.760]: rms 9 max 24 freq +42 +/- 12 delay 409 +/- 1
ptp4l[22287.763]: rms 10 max 28 freq +41 +/- 11 delay 410 +/- 1
ptp4l[22351.767]: rms 10 max 26 freq +34 +/- 12 delay 410 +/- 1
ptp4l[22415.770]: rms 10 max 26 freq +49 +/- 14 delay 410 +/- 1
=== Ext. HW_TS and Genf testing:
For testing purposes Time Sync Router (TSR) can be modeled in DT as pin controller
+ timesync_router: timesync_router@A40000 {
+ compatible = "pinctrl-single";
+ reg = <0x0 0xA40000 0x0 0x800>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x800007ff>;
+ };
then signals routing can be done in board file, for example:
+#define TS_OFFSET(pa, val) (0x4+(pa)*4) (0x80000000 | val)
+
+×ync_router {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_cpts>;
+
+ /* Example of the timesync routing */
+ mcu_cpts: mcu_cpts {
+ pinctrl-single,pins = <
+ /* [cpts genf1] in13 -> out25 [cpts hw4_push] */
+ TS_OFFSET(25, 13)
+ /* [cpts genf1] in13 -> out0 [main cpts hw1_push] */
+ TS_OFFSET(0, 13)
+ /* [main cpts genf0] in4 -> out1 [main cpts hw2_push] */
+ TS_OFFSET(1, 4)
+ /* [main cpts genf0] in4 -> out24 [cpts hw3_push] */
+ TS_OFFSET(24, 4)
+ >;
+ };
+};
will create link:
cpsw cpts Genf1 -> main cpts hw1_push
-> cpsw cpts hw4_push
main cpts Genf0 -> main cpts hw2_push
-> cpsw cpts hw3_push
testptp -d /dev/ptp0 -i 0 -p
1000000000
periodic output request okay
testptp -d /dev/ptp0 -i 1 -e 5
external time stamp request okay
event index 1 at 22583.
000000025
event index 1 at 22584.
000000025
event index 1 at 22585.
000000025
event index 1 at 22586.
000000025
event index 1 at 22587.
000000025
testptp -d /dev/ptp1 -i 2 -e 5
external time stamp request okay
event index 2 at
1587606764.
249304554
event index 2 at
1587606765.
249304467
event index 2 at
1587606766.
249304380
event index 2 at
1587606767.
249304293
event index 2 at
1587606768.
249304206
[1] https://www.ti.com/lit/pdf/spracp7
[2] https://www.ti.com/lit/pdf/sprz452
[3] https://www.ti.com/lit/pdf/spruil1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Fri, 1 May 2020 20:50:11 +0000 (23:50 +0300)]
arm64: dts: ti: j721e-main: add main navss cpts node
Add DT node for Main NAVSS CPTS module.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Fri, 1 May 2020 20:50:10 +0000 (23:50 +0300)]
arm64: dts: ti: k3-j721e-mcu: add mcu cpsw cpts node
Add DT node for The TI J721E MCU CPSW CPTS which is part of MCU CPSW NUSS.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Fri, 1 May 2020 20:50:09 +0000 (23:50 +0300)]
arm64: dts: ti: k3-am65-main: add main navss cpts node
Add DT node for Main NAVSS CPTS module.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Fri, 1 May 2020 20:50:08 +0000 (23:50 +0300)]
arm64: dts: ti: k3-am65-mcu: add cpsw cpts node
Add DT node for the TI AM65x SoC Common Platform Time Sync (CPTS).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Fri, 1 May 2020 20:50:07 +0000 (23:50 +0300)]
net: ethernet: ti: am65-cpsw-nuss: enable packet timestamping support
The MCU CPSW Common Platform Time Sync (CPTS) provides possibility to
timestamp TX PTP packets and all RX packets.
This enables corresponding support in TI AM65x/J721E MCU CPSW driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Fri, 1 May 2020 20:50:06 +0000 (23:50 +0300)]
net: ethernet: ti: introduce am654 common platform time sync driver
The CPTS module is used to facilitate host control of time sync operations.
Main features of CPTS module are:
- selection of multiple external clock sources
- control of time sync events via interrupt or polling
- 64-bit timestamp mode in ns with HW PPM and nudge adjustment.
- hardware timestamp ext. inputs (HWx_TS_PUSH)
- timestamp Generator function outputs (TS_GENFx)
Depending on integration it enables compliance with the IEEE 1588-2008
standard for a precision clock synchronization protocol, Ethernet Enhanced
Scheduled Traffic Operations (CPTS_ESTFn) and PCIe Subsystem Precision Time
Measurement (PTM).
Introduced driver provides Linux PTP hardware clock for each CPTS device
and network packets timestamping where applicable. CPTS PTP hardware clock
supports following operations:
- Set time
- Get time
- Shift the clock by a given offset atomically
- Adjust clock frequency
- Time stamp external events
- Periodic output signals
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Fri, 1 May 2020 20:50:05 +0000 (23:50 +0300)]
dt-binding: ti: am65x: document common platform time sync cpts module
Document device tree bindings for TI AM654/J721E SoC The Common Platform
Time Sync (CPTS) module. The CPTS module is used to facilitate host control
of time sync operations. Main features of CPTS module are:
- selection of multiple external clock sources
- 64-bit timestamp mode in ns with ppm and nudge adjustment.
- control of time sync events via interrupt or polling
- hardware timestamp of ext. events (HWx_TS_PUSH)
- periodic generator function outputs (TS_GENFx)
- PPS in combination with timesync router
- Depending on integration it enables compliance with the IEEE 1588-2008
standard for a precision clock synchronization protocol, Ethernet Enhanced
Scheduled Traffic Operations (CPTS_ESTFn) and PCIe Subsystem Precision Time
Measurement (PTM).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 May 2020 18:58:31 +0000 (11:58 -0700)]
Merge branch 'devlink-kernel-region-snapshot-id-allocation'
Jakub Kicinski says:
====================
devlink: kernel region snapshot id allocation
currently users have to find a free snapshot id to pass
to the kernel when they are requesting a snapshot to be
taken.
This set extends the kernel so it can allocate the id
on its own and send it back to user space in a response.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 1 May 2020 16:40:42 +0000 (09:40 -0700)]
docs: devlink: clarify the scope of snapshot id
In past discussions Jiri explained snapshot ids are cross-region.
Explain this in the docs.
v3: new patch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 1 May 2020 16:40:41 +0000 (09:40 -0700)]
devlink: let kernel allocate region snapshot id
Currently users have to choose a free snapshot id before
calling DEVLINK_CMD_REGION_NEW. This is potentially racy
and inconvenient.
Make the DEVLINK_ATTR_REGION_SNAPSHOT_ID optional and try
to allocate id automatically. Send a message back to the
caller with the snapshot info.
Example use:
$ devlink region new netdevsim/netdevsim1/dummy
netdevsim/netdevsim1/dummy: snapshot 1
$ id=$(devlink -j region new netdevsim/netdevsim1/dummy | \
jq '.[][][][]')
$ devlink region dump netdevsim/netdevsim1/dummy snapshot $id
[...]
$ devlink region del netdevsim/netdevsim1/dummy snapshot $id
v4:
- inline the notification code
v3:
- send the notification only once snapshot creation completed.
v2:
- don't wrap the line containing extack;
- add a few sentences to the docs.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 1 May 2020 16:40:40 +0000 (09:40 -0700)]
devlink: factor out building a snapshot notification
We'll need to send snapshot info back on the socket
which requested a snapshot to be created. Factor out
constructing a snapshot description from the broadcast
notification code.
v3: new patch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 May 2020 14:07:41 +0000 (07:07 -0700)]
net_sched: sch_fq: add horizon attribute
QUIC servers would like to use SO_TXTIME, without having CAP_NET_ADMIN,
to efficiently pace UDP packets.
As far as sch_fq is concerned, we need to add safety checks, so
that a buggy application does not fill the qdisc with packets
having delivery time far in the future.
This patch adds a configurable horizon (default: 10 seconds),
and a configurable policy when a packet is beyond the horizon
at enqueue() time:
- either drop the packet (default policy)
- or cap its delivery time to the horizon.
$ tc -s -d qd sh dev eth0
qdisc fq 8022: root refcnt 257 limit 10000p flow_limit 100p buckets 1024
orphan_mask 1023 quantum 10Kb initial_quantum 51160b low_rate_threshold 550Kbit
refill_delay 40.0ms timer_slack 10.000us horizon 10.000s
Sent
1234215879 bytes 837099 pkt (dropped 21, overlimits 0 requeues 6)
backlog 0b 0p requeues 6
flows 1191 (inactive 1177 throttled 0)
gc 0 highprio 0 throttled 692 latency 11.480us
pkts_too_long 0 alloc_errors 0 horizon_drops 21 horizon_caps 0
v2: fixed an overflow on 32bit kernels in fq_init(), reported
by kbuild test robot <lkp@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Thu, 30 Apr 2020 11:42:22 +0000 (13:42 +0200)]
net: sched: fallback to qdisc noqueue if default qdisc setup fail
Currently if the default qdisc setup/init fails, the device ends up with
qdisc "noop", which causes all TX packets to get dropped.
With the introduction of sysctl net/core/default_qdisc it is possible
to change the default qdisc to be more advanced, which opens for the
possibility that Qdisc_ops->init() can fail.
This patch detect these kind of failures, and choose to fallback to
qdisc "noqueue", which is so simple that its init call will not fail.
This allows the interface to continue functioning.
V2:
As this also captures memory failures, which are transient, the
device is not kept in IFF_NO_QUEUE state. This allows the net_device
to retry to default qdisc assignment.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 May 2020 18:26:55 +0000 (11:26 -0700)]
Merge branch 'net-ipa-I-O-map-SMEM-and-IMEM'
Alex Elder says:
====================
net: ipa: I/O map SMEM and IMEM
This series adds the definition of two memory regions that must be
mapped for IPA to access through an SMMU. It requires the SMMU to
be defined in the IPA node in the SoC's Device Tree file.
There is no change since version 1 to the content of the code in
these patches, *however* this time the first patch is an update to
the binding definition rather than an update to a DTS file.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Mon, 4 May 2020 17:58:59 +0000 (12:58 -0500)]
net: ipa: define SMEM memory region for IPA
Arrange to use an item from SMEM memory for IPA. SMEM item number
497 is designated to be used by the IPA. Specify the item ID and
size of the region in platform configuration data. Allocate and get
a pointer to this region from ipa_mem_init(). The memory must be
mapped for access through an SMMU.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Mon, 4 May 2020 17:58:58 +0000 (12:58 -0500)]
net: ipa: define IMEM memory region for IPA
Define a region of IMEM memory available for use by IPA in the
platform configuration data. Initialize it from ipa_mem_init().
The memory must be mapped for access through an SMMU.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Mon, 4 May 2020 17:58:57 +0000 (12:58 -0500)]
net: ipa: redefine struct ipa_mem_data
The ipa_mem_data structure type was never actually used. Instead,
the IPA memory regions were defined using the ipa_mem structure.
Redefine struct ipa_mem_data so it encapsulates the array of IPA-local
memory region descriptors along with the count of entries in that
array. Pass just an ipa_mem structure pointer to ipa_mem_init().
Rename the ipa_mem_data[] array ipa_mem_local_data[] to emphasize
that the memory regions it defines are IPA-local memory.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Mon, 4 May 2020 17:58:56 +0000 (12:58 -0500)]
dt-bindings: net: add IPA iommus property
The IPA accesses "IMEM" and main system memory through an SMMU, so
its DT node requires an iommus property to define range of stream IDs
it uses.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 May 2020 18:19:58 +0000 (11:19 -0700)]
Merge branch 'net-add-helper-eth_hw_addr_crc'
Heiner Kallweit says:
====================
net: add helper eth_hw_addr_crc
Several drivers use the same code as basis for filter hashes. Therefore
let's factor it out to a helper. This way drivers don't have to access
struct netdev_hw_addr internals.
First user is r8169.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 4 May 2020 17:28:21 +0000 (19:28 +0200)]
r8169: use new helper eth_hw_addr_crc
Use new helper eth_hw_addr_crc to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 4 May 2020 17:27:00 +0000 (19:27 +0200)]
net: add helper eth_hw_addr_crc
Several drivers use the same code as basis for filter hashes. Therefore
let's factor it out to a helper. This way drivers don't have to access
struct netdev_hw_addr internals.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Walle [Mon, 4 May 2020 16:52:28 +0000 (18:52 +0200)]
net: dsa: felix: allow the device to be disabled
If there is no specific configuration of the felix switch in the device
tree, but only the default configuration (ie. given by the SoCs dtsi
file), the probe fails because no CPU port has been set. On the other
hand you cannot set a default CPU port because that depends on the
actual board using the switch.
[ 2.701300] DSA: tree 0 has no CPU port
[ 2.705167] mscc_felix 0000:00:00.5: Failed to register DSA switch: -22
[ 2.711844] mscc_felix: probe of 0000:00:00.5 failed with error -22
Thus let the device tree disable this device entirely, like it is also
done with the enetc driver of the same SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 May 2020 17:54:40 +0000 (10:54 -0700)]
Merge branch 'net-smc-add-failover-processing'
Karsten Graul says:
====================
net/smc: add failover processing
This patch series adds the actual SMC-R link failover processing and
improved link group termination. There will be one more (very small)
series after this which will complete the SMC-R link failover support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Mon, 4 May 2020 12:18:48 +0000 (14:18 +0200)]
net/smc: save SMC-R peer link_uid
During SMC-R link establishment the peers exchange the link_uid that
is used for debugging purposes. Save the peer link_uid in smc_link so it
can be retrieved by the smc_diag netlink interface.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Mon, 4 May 2020 12:18:47 +0000 (14:18 +0200)]
net/smc: create improved SMC-R link_uid
The link_uid of an SMC-R link is exchanged between SMC peers and its
value can be used for debugging purposes. Create a unique link_uid
during link initialization and use it in communication with SMC-R peers.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Mon, 4 May 2020 12:18:46 +0000 (14:18 +0200)]
net/smc: improve termination processing
Add helper smcr_lgr_link_deactivate_all() and eliminate duplicate code.
In smc_lgr_free(), clear the smc-r links before smc_lgr_free_bufs() is
called so buffers are already prepared for free. The usage of the soft
parameter in __smc_lgr_terminate() is no longer needed, smc_lgr_free()
can be called directly. smc_lgr_terminate_sched() and
smc_smcd_terminate() set lgr->freeing to indicate that the link group
will be freed soon to avoid unnecessary schedules of the free worker.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Mon, 4 May 2020 12:18:45 +0000 (14:18 +0200)]
net/smc: add termination reason and handle LLC protocol violation
Allow to set the reason code for the link group termination, and set
meaningful values before termination processing is triggered. This
reason code is sent to the peer in the final delete link message.
When the LLC request or response layer receives a message type that was
not handled, drop a warning and terminate the link group.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Mon, 4 May 2020 12:18:44 +0000 (14:18 +0200)]
net/smc: asymmetric link tagging
New connections must not be assigned to asymmetric links. Add asymmetric
link tagging using new link variable link_is_asym. The new helpers
smcr_lgr_set_type() and smcr_lgr_set_type_asym() are called to set the
state of the link group, and tag all links accordingly.
smcr_lgr_conn_assign_link() respects the link tagging and will not
assign new connections to links tagged as asymmetric link.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Mon, 4 May 2020 12:18:43 +0000 (14:18 +0200)]
net/smc: assign link to a new connection
For new connections, assign a link from the link group, using some
simple load balancing.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Mon, 4 May 2020 12:18:42 +0000 (14:18 +0200)]
net/smc: send DELETE_LINK, ALL message and wait for send to complete
Add smc_llc_send_message_wait() which uses smc_wr_tx_send_wait() to send
an LLC message and waits for the message send to complete.
smc_llc_send_link_delete_all() calls the new function to send an
DELETE_LINK,ALL LLC message. The RFC states that the sender of this type
of message needs to wait for the completion event of the message
transmission and can terminate the link afterwards.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Mon, 4 May 2020 12:18:41 +0000 (14:18 +0200)]
net/smc: wait for departure of an IB message
Introduce smc_wr_tx_send_wait() to send an IB message and wait for the
tx completion event of the message. This makes sure that the message is
no longer in-flight when the function returns.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Mon, 4 May 2020 12:18:40 +0000 (14:18 +0200)]
net/smc: handle incoming CDC validation message
Call smc_cdc_msg_validate() when a CDC message with the failover
validation bit enabled was received. Validate that the sequence number
sent with the message is one we already have received. If not, messages
were lost and the connection is terminated using a new abort_work.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Mon, 4 May 2020 12:18:39 +0000 (14:18 +0200)]
net/smc: send failover validation message
When a connection is switched to a new link then a link validation
message must be sent to the peer over the new link, containing the
sequence number of the last CDC message that was sent over the old link.
The peer will validate if this sequence number is the same or lower then
the number he received, and abort the connection if messages were lost.
Add smcr_cdc_msg_send_validation() to send the message validation
message and call it when a connection was switched in
smc_switch_cursor().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Mon, 4 May 2020 12:18:38 +0000 (14:18 +0200)]
net/smc: switch connections to alternate link
Add smc_switch_conns() to switch all connections from a link that is
going down. Find an other link to switch the connections to, and
switch each connection to the new link. smc_switch_cursor() updates the
cursors of a connection to the state of the last successfully sent CDC
message. When there is no link to switch to, terminate the link group.
Call smc_switch_conns() when a link is going down.
And with the possibility that links of connections can switch adapt CDC
and TX functions to detect and handle link switches.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Mon, 4 May 2020 12:18:37 +0000 (14:18 +0200)]
net/smc: save state of last sent CDC message
When a link goes down and all connections of this link need to be
switched to an other link then the producer cursor and the sequence of
the last successfully sent CDC message must be known. Add the two fields
to the SMC connection and update it in the tx completion handler.
And to allow matching of sequences in error cases reset the seqno to the
old value in smc_cdc_msg_send() when the actual send failed.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 May 2020 17:44:11 +0000 (10:44 -0700)]
Merge branch 'bnxt_en-Updates-for-net-next'
Michael Chan says:
====================
bnxt_en: Updates for net-next.
This patchset includes these main changes:
1. Firmware spec. update.
2. Context memory sizing improvements for the hardware TQM block.
3. ethtool chip reset improvements and fixes for correctness.
4. Improve L2 doorbell mapping by mapping only up to the size specified
by firmware. This allows the RoCE driver to map the remaining doorbell
space for its purpose, such as write-combining.
5. Improve ethtool -S channel statistics by showing only relevant ring
counters for non-combined channels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rajesh Ravi [Mon, 4 May 2020 08:50:41 +0000 (04:50 -0400)]
bnxt_en: show only relevant ethtool stats for a TX or RX ring
Currently, ethtool -S shows all TX/RX ring counters whether the
channel is combined, RX, or TX. The unused counters will always be
zero. Improve it by showing only the relevant counters if the channel
is RX or TX. If the channel is combined, the counters will be shown
exactly the same as before.
[ MChan: Lots of cleanups and simplifications on Rajesh's original
code]
Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 4 May 2020 08:50:40 +0000 (04:50 -0400)]
bnxt_en: Split HW ring statistics strings into RX and TX parts.
This will allow the RX and TX ring statistics to be separated if needed.
In the next patch, we'll be able to only display RX or TX statistcis if
the channel is RX only or TX only.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 4 May 2020 08:50:39 +0000 (04:50 -0400)]
bnxt_en: Refactor the software ring counters.
We currently have 3 software ring counters, rx_l4_csum_errors,
rx_buf_errors, and missed_irqs. The 1st two are RX counters and the
last one is a common counter. Organize them into 2 structures
bnxt_rx_sw_stats and bnxt_cmn_sw_stats.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>