OSDN Git Service
Alexander Duyck [Fri, 5 Feb 2016 23:27:55 +0000 (15:27 -0800)]
net: Move skb_has_shared_frag check out of GRE code and into segmentation
The call skb_has_shared_frag is used in the GRE path and skb_checksum_help
to verify that no frags can be modified by an external entity. This check
really doesn't belong in the GRE path but in the skb_segment function
itself. This way any protocol that might be segmented will be performing
this check before attempting to offload a checksum to software.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 5 Feb 2016 23:27:49 +0000 (15:27 -0800)]
net: Store checksum result for offloaded GSO checksums
This patch makes it so that we can offload the checksums for a packet up
to a certain point and then begin computing the checksums via software.
Setting this up is fairly straight forward as all we need to do is reset
the values stored in csum and csum_start for the GSO context block.
One complication for this is remote checksum offload. In order to allow
the inner checksums to be offloaded while computing the outer checksum
manually we needed to have some way of indicating that the offload wasn't
real. In order to do that I replaced CHECKSUM_PARTIAL with
CHECKSUM_UNNECESSARY in the case of us computing checksums for the outer
header while skipping computing checksums for the inner headers. We clean
up the ip_summed flag and set it to either CHECKSUM_PARTIAL or
CHECKSUM_NONE once we hand the packet off to the next lower level.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 5 Feb 2016 23:27:43 +0000 (15:27 -0800)]
net: Update remote checksum segmentation to support use of GSO checksum
This patch addresses two main issues.
First in the case of remote checksum offload we were avoiding dealing with
scatter-gather issues. As a result it would be possible to assemble a
series of frames that used frags instead of being linearized as they should
have if remote checksum offload was enabled.
Second I have updated the code so that we now let GSO take care of doing
the checksum on the data itself and drop the special case that was added
for remote checksum offload.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 5 Feb 2016 23:27:37 +0000 (15:27 -0800)]
net: Move GSO csum into SKB_GSO_CB
This patch moves the checksum maintained by GSO out of skb->csum and into
the GSO context block in order to allow for us to work on outer checksums
while maintaining the inner checksum offsets in the case of the inner
checksum being offloaded, while the outer checksums will be computed.
While updating the code I also did a minor cleanu-up on gso_make_checksum.
The change is mostly to make it so that we store the values and compute the
checksum instead of computing the checksum and then storing the values we
needed to update.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 5 Feb 2016 23:27:31 +0000 (15:27 -0800)]
net: Drop unecessary enc_features variable from tunnel segmentation functions
The enc_features variable isn't necessary since features isn't used
anywhere after we create enc_features so instead just use a destructive AND
on features itself and save ourselves the variable declaration.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sixiao@microsoft.com [Thu, 4 Feb 2016 23:49:34 +0000 (15:49 -0800)]
hv_netvsc: cleanup netdev feature flags for netvsc
1. Adding NETIF_F_TSO6 feature flag;
2. Adding NETIF_F_HW_CSUM. NETIF_F_IPV6_CSUM and NETIF_F_IP_CSUM are
being deprecated;
3. Cleanup the coding style of flag assignment by using macro.
Signed-off-by: Simon Xiao <sixiao@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 11 Feb 2016 12:16:29 +0000 (07:16 -0500)]
Merge branch 'ethtool-nfc-ipv6'
Edward Cree says:
====================
IPv6 NFC
This series adds support for steering IPv6 flows using the ethtool NFC
interface, and implements it for sfc devices.
Tested using an in-development patch to the ethtool utility.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Fri, 5 Feb 2016 11:16:50 +0000 (11:16 +0000)]
sfc: implement IPv6 NFC (and IPV4_USER_FLOW)
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Fri, 5 Feb 2016 11:16:21 +0000 (11:16 +0000)]
ethtool: add IPv6 to the NFC API
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 11 Feb 2016 12:13:29 +0000 (07:13 -0500)]
Merge branch 'cxgb4-tos'
Hariprasad Shenai says:
====================
Add TOS support and some cleanup
This series adds TOS support for iWARP and also does some cleanup to make
code more readable. Patch series is created against infiniband tree and
includes patches on iw_cxgb4 and cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 5 Feb 2016 06:13:30 +0000 (11:43 +0530)]
cxgb4/iw_cxgb4: TOS support
This series provides support for iWARP applications to specify a TOS
value and have that map to a VLAN Priority for iw_cxgb4 iWARP connections.
In iw_cxgb4, when allocating an L2T entry, pass the skb_priority based
on the tos value in the cm_id. Also pass the correct tos value during
connection setup so the passive side gets the client's desired tos.
When sending the FLOWC work request to FW, if the egress device is
in a vlan, then use the vlan priority bits as the scheduling class.
This allows associating RDMA connections with scheduling classes to
provide traffic shaping per flow.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 5 Feb 2016 06:13:29 +0000 (11:43 +0530)]
iw_cxgb4: remove false error log entry
Don't log errors if a listening endpoint is going away when procesing a
PASS_ACCEPT_REQ message. This can happen. Change the error printk to
a PDBG() debug log entry
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 5 Feb 2016 06:13:28 +0000 (11:43 +0530)]
iw_cxgb4: make queue allocation code more readable
Rename local mm* variables to more meaningful names
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 11 Feb 2016 11:15:00 +0000 (06:15 -0500)]
Merge branch 'fec-next'
Troy Kisky says:
====================
net: fec: cleanup/fixes
V2 is a rebase on top of johannes endian-safe patch and
is only the 1st eight patches.
The testing for this series was done on a nitrogen6x.
The base commit was
commit
b45efa30a626e915192a6c548cd8642379cd47cc
Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Testing showed no change in performance.
Testing used imx_v6_v7_defconfig + CONFIG_MICREL_PHY.
The processor was running at 996Mhz.
The following commands were used to get the transfer rates.
On an x86 ubunto system,
iperf -s -i.5 -u
On a nitrogen6x board, running via SD Card.
I first stopped some background processes
stop cron
stop upstart-file-bridge
stop upstart-socket-bridge
stop upstart-udev-bridge
stop rsyslog
stop dbus
killall dhclient
echo performance >/sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
taskset 0x2 iperf -c 192.168.0.201 -u -t60 -b500M -r
There is a branch available on github with this series, and the rest of
my fec patches, for those who would like to test it.
https://github.com:boundarydevices/linux-imx6.git branch net-next_master
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Troy Kisky [Fri, 5 Feb 2016 21:52:50 +0000 (14:52 -0700)]
net: fec: improve error handling
Unmap initial buffer on error.
Don't free skb until it has been unmapped.
Move cbd_bufaddr assignment closer to the mapping function.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Troy Kisky [Fri, 5 Feb 2016 21:52:49 +0000 (14:52 -0700)]
net: fec: don't transfer ownership until descriptor write is complete
If you don't own it, you shouldn't write to it.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Troy Kisky [Fri, 5 Feb 2016 21:52:48 +0000 (14:52 -0700)]
net: fec: don't disable FEC_ENET_TS_TIMER interrupt
Only the interrupt routine processes this condition.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Troy Kisky [Fri, 5 Feb 2016 21:52:47 +0000 (14:52 -0700)]
net: fec: add variable reg_desc_active to speed things up
There is no need for complex macros every time we need to activate
a queue. Also, no need to call skb_get_queue_mapping when we already
know which queue it is using.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Troy Kisky [Fri, 5 Feb 2016 21:52:46 +0000 (14:52 -0700)]
net: fec: add struct bufdesc_prop
This reduces code and gains speed.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Troy Kisky [Fri, 5 Feb 2016 21:52:45 +0000 (14:52 -0700)]
net: fec: fix fec_enet_get_free_txdesc_num
When first initialized, cur_tx points to the 1st
entry in the queue, and dirty_tx points to the last.
At this point, fec_enet_get_free_txdesc_num will
return tx_ring_size -2. If tx_ring_size -2 entries
are now queued, then fec_enet_get_free_txdesc_num
should return 0, but it returns tx_ring_size instead.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Troy Kisky [Fri, 5 Feb 2016 21:52:44 +0000 (14:52 -0700)]
net: fec: fix rx error counts
On an overrun, the other flags are not
valid, so don't check them.
Also, don't pass bad frames up the stack.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Troy Kisky [Fri, 5 Feb 2016 21:52:43 +0000 (14:52 -0700)]
net: fec: stop the "rcv is not +last, " error messages
Setting the FTRL register will stop the fec from
trying to use multiple receive buffers.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Thu, 4 Feb 2016 16:42:28 +0000 (17:42 +0100)]
bonding: 3ad: allow to set ad_actor settings while the bond is up
No need to require the bond down while changing these settings, the change
will be reflected immediately and the 3ad mode will sort itself out.
For faster convergence set port->ntt to true in order to generate new
LACPDUs immediately.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Thu, 4 Feb 2016 12:31:20 +0000 (13:31 +0100)]
ipv6: add option to drop unsolicited neighbor advertisements
In certain 802.11 wireless deployments, there will be NA proxies
that use knowledge of the network to correctly answer requests.
To prevent unsolicitd advertisements on the shared medium from
being a problem, on such deployments wireless needs to drop them.
Enable this by providing an option called "drop_unsolicited_na".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Thu, 4 Feb 2016 12:31:19 +0000 (13:31 +0100)]
ipv6: add option to drop unicast encapsulated in L2 multicast
In order to solve a problem with 802.11, the so-called hole-196 attack,
add an option (sysctl) called "drop_unicast_in_l2_multicast" which, if
enabled, causes the stack to drop IPv6 unicast packets encapsulated in
link-layer multi- or broadcast frames. Such frames can (as an attack)
be created by any member of the same wireless network and transmitted
as valid encrypted frames since the symmetric key for broadcast frames
is shared between all stations.
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Thu, 4 Feb 2016 12:31:18 +0000 (13:31 +0100)]
ipv4: add option to drop gratuitous ARP packets
In certain 802.11 wireless deployments, there will be ARP proxies
that use knowledge of the network to correctly answer requests.
To prevent gratuitous ARP frames on the shared medium from being
a problem, on such deployments wireless needs to drop them.
Enable this by providing an option called "drop_gratuitous_arp".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Thu, 4 Feb 2016 12:31:17 +0000 (13:31 +0100)]
ipv4: add option to drop unicast encapsulated in L2 multicast
In order to solve a problem with 802.11, the so-called hole-196 attack,
add an option (sysctl) called "drop_unicast_in_l2_multicast" which, if
enabled, causes the stack to drop IPv4 unicast packets encapsulated in
link-layer multi- or broadcast frames. Such frames can (as an attack)
be created by any member of the same wireless network and transmitted
as valid encrypted frames since the symmetric key for broadcast frames
is shared between all stations.
Additionally, enabling this option provides compliance with a SHOULD
clause of RFC 1122.
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siva Reddy Kallam [Thu, 4 Feb 2016 09:50:47 +0000 (15:20 +0530)]
MAINTAINERS: Update tg3 maintainer
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Tang [Thu, 4 Feb 2016 09:36:23 +0000 (17:36 +0800)]
bpf_dbg: do not initialise statics to 0
This patch fixes the checkpatch.pl error to bpf_dbg.c:
ERROR: do not initialise statics to 0
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 2 Feb 2016 16:17:07 +0000 (08:17 -0800)]
net: Add support for filtering link dump by master device and kind
Add support for filtering link dumps by master device and kind, similar
to the filtering implemented for neighbor dumps.
Each net_device that exists adds between 1196 bytes (eth) and 1556 bytes
(bridge) to the link dump. As the number of interfaces increases so does
the amount of data pushed to user space for a link list. If the user
only wants to see a list of specific devices (e.g., interfaces enslaved
to a specific bridge or a list of VRFs) most of that data is thrown away.
Passing the filters to the kernel to have only relevant data returned
makes the dump more efficient.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 11 Feb 2016 08:54:23 +0000 (03:54 -0500)]
Merge branch 'tcp-fast-so_reuseport'
Craig Gallek says:
====================
Faster SO_REUSEPORT for TCP
This patch series complements an earlier series (
6a5ef90c58da)
which added faster SO_REUSEPORT lookup for UDP sockets by
extending the feature to TCP sockets. It uses the same
array-based data structure which allows for socket selection
after finding the first listening socket that matches an incoming
packet. Prior to this feature, every socket in the reuseport
group needed to be found and examined before a selection could be
made.
With this series the SO_ATTACH_REUSEPORT_CBPF and
SO_ATTACH_REUSEPORT_EBPF socket options now work for TCP sockets
as well. The test at the end of the series includes an example of
how to use these options to select a reuseport socket based on the
cpu core id handling the incoming packet.
There are several refactoring patches that precede the feature
implementation. Only the last two patches in this series
should result in any behavioral changes.
v4
- Fix build issue when compiling IPv6 as a module. This required
moving the ipv6_rcv_saddr_equal into an object that is included as a
built-in object. I included this change in the second patch which
adds inet6_hash since that is where ipv6_rcv_saddr_equal will
later be called from non-module code.
v3:
- Another warning in the first patch caught by a build bot. Return 0 in
the no-op UDP hash function.
v2:
- In the first patched I missed a couple of hash functions that should now be
returning int instead of void. I missed these the first time through as it
only generated a warning and not an error :\
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Craig Gallek [Wed, 10 Feb 2016 16:50:41 +0000 (11:50 -0500)]
soreuseport: BPF selection functional test for TCP
Unfortunately the existing test relied on packet payload in order to
map incoming packets to sockets. In order to get this to work with TCP,
TCP_FASTOPEN needed to be used.
Since the fast open path is slightly different than the standard TCP path,
I created a second test which sends to reuseport group members based
on receiving cpu core id. This will probably serve as a better
real-world example use as well.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Craig Gallek [Wed, 10 Feb 2016 16:50:40 +0000 (11:50 -0500)]
soreuseport: fast reuseport TCP socket selection
This change extends the fast SO_REUSEPORT socket lookup implemented
for UDP to TCP. Listener sockets with SO_REUSEPORT and the same
receive address are additionally added to an array for faster
random access. This means that only a single socket from the group
must be found in the listener list before any socket in the group can
be used to receive a packet. Previously, every socket in the group
needed to be considered before handing off the incoming packet.
This feature also exposes the ability to use a BPF program when
selecting a socket from a reuseport group.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Craig Gallek [Wed, 10 Feb 2016 16:50:39 +0000 (11:50 -0500)]
soreuseport: Prep for fast reuseport TCP socket selection
Both of the lines in this patch probably should have been included
in the initial implementation of this code for generic socket
support, but weren't technically necessary since only UDP sockets
were supported.
First, the sk_reuseport_cb points to a structure which assumes
each socket in the group has this pointer assigned at the same
time it's added to the array in the structure. The sk_clone_lock
function breaks this assumption. Since a child socket shouldn't
implicitly be in a reuseport group, the simple fix is to clear
the field in the clone.
Second, the SO_ATTACH_REUSEPORT_xBPF socket options require that
SO_REUSEPORT also be set first. For UDP sockets, this is easily
enforced at bind-time since that process both puts the socket in
the appropriate receive hlist and updates the reuseport structures.
Since these operations can happen at two different times for TCP
sockets (bind and listen) it must be explicitly checked to enforce
the use of SO_REUSEPORT with SO_ATTACH_REUSEPORT_xBPF in the
setsockopt call.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Craig Gallek [Wed, 10 Feb 2016 16:50:38 +0000 (11:50 -0500)]
inet: refactor inet[6]_lookup functions to take skb
This is a preliminary step to allow fast socket lookup of SO_REUSEPORT
groups. Doing so with a BPF filter will require access to the
skb in question. This change plumbs the skb (and offset to payload
data) through the call stack to the listening socket lookup
implementations where it will be used in a following patch.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Craig Gallek [Wed, 10 Feb 2016 16:50:37 +0000 (11:50 -0500)]
tcp: __tcp_hdrlen() helper
tcp_hdrlen is wasteful if you already have a pointer to struct tcphdr.
This splits the size calculation into a helper function that can be
used if a struct tcphdr is already available.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Craig Gallek [Wed, 10 Feb 2016 16:50:36 +0000 (11:50 -0500)]
inet: create IPv6-equivalent inet_hash function
In order to support fast lookups for TCP sockets with SO_REUSEPORT,
the function that adds sockets to the listening hash set needs
to be able to check receive address equality. Since this equality
check is different for IPv4 and IPv6, we will need two different
socket hashing functions.
This patch adds inet6_hash identical to the existing inet_hash function
and updates the appropriate references. A following patch will
differentiate the two by passing different comparison functions to
__inet_hash.
Additionally, in order to use the IPv6 address equality function from
inet6_hashtables (which is compiled as a built-in object when IPv6 is
enabled) it also needs to be in a built-in object file as well. This
moves ipv6_rcv_saddr_equal into inet_hashtables to accomplish this.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Craig Gallek [Wed, 10 Feb 2016 16:50:35 +0000 (11:50 -0500)]
sock: struct proto hash function may error
In order to support fast reuseport lookups in TCP, the hash function
defined in struct proto must be capable of returning an error code.
This patch changes the function signature of all related hash functions
to return an integer and handles or propagates this return value at
all call sites.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 11 Feb 2016 08:49:55 +0000 (03:49 -0500)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Here you have a batch of patches by Sven Eckelmann that
drops our private reference counting implementation and
substitutes it with the kref objects/functions.
Then you have a patch, by Simon Wunderlich, that
makes the broadcast protection window code more generic so
that it can be re-used in the future by other components
with different requirements.
Lastly, Sven is also introducing two lockdep asserts in
functions operating on our TVLV container list, to make
sure that the proper lock is always acquired by the users.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 11 Feb 2016 08:47:05 +0000 (03:47 -0500)]
Merge branch 'be2net-next'
Ajit Khaparde says:
====================
be2net Patch series
Please consider applying these two patches to net-next
Patch-1: Request RSS capability of Rx interface depending on number of
Rx rings
Patch-2: Interpret and log new data that's added to the port
misconfigure async event
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Wed, 10 Feb 2016 17:15:54 +0000 (22:45 +0530)]
be2net: Interpret and log new data that's added to the port misconfigure async event
>From FW version 11.0. onwards, the PORT_MISCONFIG event generated by the FW
will carry more information about the event in the "data_word1"
and "data_word2" fields. This patch adds support in the driver to parse the
new information and log it accordingly. This patch also changes some of the
messages that are being logged currently.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Wed, 10 Feb 2016 17:15:53 +0000 (22:45 +0530)]
be2net: Request RSS capability of Rx interface depending on number of Rx rings
Currently we request RSS capability even if a single Rx ring is created.
As a result in few cases we unnecessarily consume an RSS capable interface
which is a limited resource in the chip.
This patch enables RSS on an interface only if more than one Rx ring
is created.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:57 +0000 (10:29 +0100)]
batman-adv: Convert batadv_tt_common_entry to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:56 +0000 (10:29 +0100)]
batman-adv: Convert batadv_orig_node to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:55 +0000 (10:29 +0100)]
batman-adv: Convert batadv_orig_node_vlan to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:54 +0000 (10:29 +0100)]
batman-adv: Convert batadv_hard_iface to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:53 +0000 (10:29 +0100)]
batman-adv: Convert batadv_neigh_node to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:52 +0000 (10:29 +0100)]
batman-adv: Convert batadv_orig_ifinfo to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:51 +0000 (10:29 +0100)]
batman-adv: Convert batadv_neigh_ifinfo to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:50 +0000 (10:29 +0100)]
batman-adv: Convert batadv_tt_orig_list_entry to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:49 +0000 (10:29 +0100)]
batman-adv: Convert batadv_tvlv_handler to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:48 +0000 (10:29 +0100)]
batman-adv: Convert batadv_tvlv_container to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:47 +0000 (10:29 +0100)]
batman-adv: Convert batadv_dat_entry to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:46 +0000 (10:29 +0100)]
batman-adv: Convert batadv_nc_path to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:45 +0000 (10:29 +0100)]
batman-adv: Convert batadv_nc_node to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:44 +0000 (10:29 +0100)]
batman-adv: Convert batadv_bla_claim to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:43 +0000 (10:29 +0100)]
batman-adv: Convert batadv_bla_backbone_gw to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:42 +0000 (10:29 +0100)]
batman-adv: Convert batadv_softif_vlan to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:41 +0000 (10:29 +0100)]
batman-adv: Convert batadv_gw_node to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 16 Jan 2016 09:29:40 +0000 (10:29 +0100)]
batman-adv: Convert batadv_hardif_neigh_node to kref
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sun, 20 Dec 2015 08:04:03 +0000 (09:04 +0100)]
batman-adv: Add lockdep assert for container_list_lock
The batadv_tvlv_container* functions state in their kernel-doc that they
require tvlv.container_list_lock. Add an assert to automatically detect
when this might have been ignored by the caller.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Simon Wunderlich [Mon, 23 Nov 2015 18:57:22 +0000 (19:57 +0100)]
batman-adv: add seqno maximum age and protection start flag parameters
To allow future use of the window protected function with different
maximum sequence numbers, add a parameter to set this value which
was previously hardcoded. Another parameter added for future use is a
flag to return whether the protection window has started.
While at it, also fix the kerneldoc.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Tue, 5 Jan 2016 11:06:26 +0000 (12:06 +0100)]
batman-adv: Drop reference to netdevice on last reference
The references to the network device should be dropped inside the release
function for batadv_hard_iface similar to what is done with the batman-adv
internal datastructures.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Jean Sacren [Wed, 10 Feb 2016 03:47:17 +0000 (20:47 -0700)]
sxgbe: remove unused code
Remove the unused code of sxgbe_xpcs.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Byungho An <bh74.an@samsung.com>
Cc: Girish K S <ks.giri@samsung.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1601191918470.2531@hadrien
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 10 Feb 2016 10:38:19 +0000 (05:38 -0500)]
Merge branch 'renesas-bit-twiddling'
Sergei Shtylyov says:
====================
Factor out register bit twiddling in the Renesas Ethernet drivers
Here's a set of 2 patches against DaveM's 'net-next.git' repo. We factor out
the often repeated pattern of reading a register, AND'ing and/or OR'ing some
bits, and then writing the value back.
[1/2] ravb: factor out register bit twiddling code
[2/2] sh_eth: factor out register bit twiddling code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Tue, 9 Feb 2016 22:38:28 +0000 (01:38 +0300)]
sh_eth: factor out register bit twiddling code
The driver has often repeated pattern of reading a register, AND'ing and/or
OR'ing some bits and writing the value back. Factor the pattern out into
sh_eth_modify() -- this saves 84 bytes of code with ARM gcc 4.7.3.
While at it, update Cogent Embedded's copyright.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Tue, 9 Feb 2016 22:37:44 +0000 (01:37 +0300)]
ravb: factor out register bit twiddling code
The driver has often repeated pattern of reading a register, AND'ing and/or
OR'ing some bits and writing the value back. Factor the pattern out into
ravb_modify() -- this saves 260 bytes of code with ARM gcc 4.7.3.
While at it, update Cogent Embedded's copyrights.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 9 Feb 2016 11:43:59 +0000 (06:43 -0500)]
Merge branch 'tpacket-gso-csum-offload'
Willem de Bruijn says:
====================
packet: tpacket gso and csum offload
Extend PACKET_VNET_HDR socket option support to packet sockets with
memory mapped rings.
Patches 2 and 4 add support to tpacket_rcv and tpacket_snd.
Patch 1 prepares for this by moving the relevant virtio_net_hdr
logic out of packet_snd and packet_rcv into helper functions.
GSO transmission requires all headers in the skb linear section.
Patch 3 moves parsing of tx_ring slot headers before skb allocation
to enable allocation with sufficient linear size.
Changes
v1->v2:
- fix bounds checks:
- subtract sizeof(vnet_hdr) before comparing tp_len to size_max
- compare tp_len to size_max also with GSO, just do not truncate to MTU
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Wed, 3 Feb 2016 23:02:17 +0000 (18:02 -0500)]
packet: tpacket_snd gso and checksum offload
Support socket option PACKET_VNET_HDR together with PACKET_TX_RING.
When enabled, a struct virtio_net_hdr is expected to precede the data
in the ring. The vnet option must be set before the ring is created.
The implementation reuses the existing skb_copy_bits code that is used
when dev->hard_header_len is non-zero. Move this ll_header check to
before the skb alloc and combine it with a test for vnet_hdr->hdr_len.
Allocate and copy the max of the two.
Verified with test program at
github.com/wdebruij/kerneltools/blob/master/tests/psock_txring_vnet.c
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Wed, 3 Feb 2016 23:02:16 +0000 (18:02 -0500)]
packet: parse tpacket header before skb alloc
GSO packet headers must be stored in the linear skb segment.
Move tpacket header parsing before sock_alloc_send_skb. The GSO
follow-on patch will later increase the skb linear argument to
sock_alloc_send_skb if needed for large packets.
The header parsing code does not require an allocated skb, so is
safe to move. Later pass to tpacket_fill_skb the computed data
start and length.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Wed, 3 Feb 2016 23:02:15 +0000 (18:02 -0500)]
packet: vnet_hdr support for tpacket_rcv
Support socket option PACKET_VNET_HDR together with PACKET_RX_RING.
When enabled, a struct virtio_net_hdr will precede the data in the
packet ring slots.
Verified with test program at
github.com/wdebruij/kerneltools/blob/master/tests/psock_rxring_vnet.c
pkt:
1454269209.798420 len=5066
vnet: gso_type=tcpv4 gso_size=1448 hlen=66 ecn=off
csum: start=34 off=16
eth: proto=0x800
ip: src=<masked> dst=<masked> proto=6 len=5052
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Wed, 3 Feb 2016 23:02:14 +0000 (18:02 -0500)]
packet: move vnet_hdr code to helper functions
packet_snd and packet_rcv support virtio net headers for GSO.
Move this logic into helper functions to be able to reuse it in
tpacket_snd and tpacket_rcv.
This is a straighforward code move with one exception. Instead of
creating and passing a separate gso_type variable, reuse
vnet_hdr.gso_type after conversion from virtio to kernel gso type.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Wed, 3 Feb 2016 12:17:01 +0000 (13:17 +0100)]
bonding: 3ad: apply ad_actor settings changes immediately
Currently the bonding allows to set ad_actor_system and prio while the
bond device is down, but these are actually applied only if there aren't
any slaves yet (applied to bond device when first slave shows up, and to
slaves at 3ad bind time). After this patch changes are applied immediately
and the new values can be used/seen after the bond's upped so it's not
necessary anymore to release all and enslave again to see the changes.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 9 Feb 2016 09:42:55 +0000 (04:42 -0500)]
Merge branch 'bridge-mdb-entry-offload-flag'
Jiri Pirko says:
====================
bridge: mdb: flag offloaded mdb entries
This patchset extends uapi to let the user know if an mdb entry is offloaded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Elad Raz [Wed, 3 Feb 2016 08:57:06 +0000 (09:57 +0100)]
bridge: mdb: Passing the port-group pointer to br_mdb module
Passing the port-group to br_mdb in order to allow direct access to the
structure. br_mdb will later use the structure to reflect HW reflection
status via "state" variable.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Elad Raz [Wed, 3 Feb 2016 08:57:05 +0000 (09:57 +0100)]
bridge: mdb: Separate br_mdb_entry->state from net_bridge_port_group->state
Change net_bridge_port_group 'state' member to 'flags' and define new set
of flags internal to the kernel.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Elad Raz [Wed, 3 Feb 2016 08:57:04 +0000 (09:57 +0100)]
bridge: mdb: add support for offloaded mdb entries
Add new bitmask member 'flags' to br_mdb_entry structure. Adding
MDB_FLAGS_OFFLOAD bit which indicates MDB entries is offloaded to hardware.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Shengju [Wed, 3 Feb 2016 02:02:32 +0000 (02:02 +0000)]
bonding: trivial: style fixes
remove some redudant brackets, use sizeof(*) instead of sizeof(struct x).
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 8 Feb 2016 09:24:33 +0000 (04:24 -0500)]
tcp: Fix syncookies sysctl default.
Unintentionally the default was changed to zero, fix
that.
Fixes:
12ed8244ed ("ipv4: Namespaceify tcp syncookies sysctl knob")
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 7 Feb 2016 19:36:21 +0000 (14:36 -0500)]
Merge branch 'ns-tcp-sysctls'
Nikolay Borisov says:
====================
Namespaceify more of the tcp sysctl knobs
This patch series continues making more of the tcp-related
sysctl knobs be per net-namespace. Most of these apply per
socket and have global defaults so should be safe and I
don't expect any breakages.
Having those per net-namespace is useful when multiple
containers are hosted and it is required to tune the
tcp settings for each independently of the host node.
I've split the patches to be per-sysctl but after
the review if the outcome is positive I'm happy
to either send it in one big blob or just.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Borisov [Wed, 3 Feb 2016 07:46:57 +0000 (09:46 +0200)]
ipv4: Namespaceify tcp_notsent_lowat sysctl knob
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Borisov [Wed, 3 Feb 2016 07:46:56 +0000 (09:46 +0200)]
ipv4: Namespaceify tcp_fin_timeout sysctl knob
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Borisov [Wed, 3 Feb 2016 07:46:55 +0000 (09:46 +0200)]
ipv4: Namespaceify tcp_orphan_retries sysctl knob
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Borisov [Wed, 3 Feb 2016 07:46:54 +0000 (09:46 +0200)]
ipv4: Namespaceify tcp_retries2 sysctl knob
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Borisov [Wed, 3 Feb 2016 07:46:53 +0000 (09:46 +0200)]
ipv4: Namespaceify tcp_retries1 sysctl knob
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Borisov [Wed, 3 Feb 2016 07:46:52 +0000 (09:46 +0200)]
ipv4: Namespaceify tcp reordering sysctl knob
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Borisov [Wed, 3 Feb 2016 07:46:51 +0000 (09:46 +0200)]
ipv4: Namespaceify tcp syncookies sysctl knob
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Borisov [Wed, 3 Feb 2016 07:46:50 +0000 (09:46 +0200)]
ipv4: Namespaceify tcp synack retries sysctl knob
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Borisov [Wed, 3 Feb 2016 07:46:49 +0000 (09:46 +0200)]
ipv4: Namespaceify tcp syn retries sysctl knob
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 7 Feb 2016 19:32:50 +0000 (14:32 -0500)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
This batch of patches includes a number of corrections and
improvements for our kernel-doc. These changes also make sure
that our doc is now properly processed by the kernel-doc
parsing tool.
Other than that you have a patch updating all the copyright
lines to 2016 and another patch switching the URLs in our
readme, Kconfig and MAINTAINERS file from "http" to "https".
Both by Sven Eckelmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 7 Feb 2016 19:30:55 +0000 (14:30 -0500)]
Merge branch 'virtio_net_ethtool_settings'
Nikolay Aleksandrov says:
====================
virtio_net: add ethtool get/set settings support
Patch 1 adds ethtool speed/duplex validation functions which check if the
value is defined. Patch 2 adds support for ethtool (get|set)_settings and
uses the validation functions to check the user-supplied values.
v2: split in 2 patches to allow everyone to make use of the validation
functions and allow virtio_net devices to be half duplex
v3: added a check to return error if the user tries to change anything else
besides duplex/speed as per Michael's comment
v4: Set port type to PORT_OTHER
v5: clear diff1.port (ignore port) when checking for changes since we set
it now and ethtool uses it in the set request
Sorry about the pointless iterations, should've all covered now.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Wed, 3 Feb 2016 03:04:37 +0000 (04:04 +0100)]
virtio_net: add ethtool support for set and get of settings
This patch allows the user to set and retrieve speed and duplex of the
virtio_net device via ethtool. Having this functionality is very helpful
for simulating different environments and also enables the virtio_net
device to participate in operations where proper speed and duplex are
required (e.g. currently bonding lacp mode requires full duplex). Custom
speed and duplex are not allowed, the user-supplied settings are validated
before applying.
Example:
$ ethtool eth1
Settings for eth1:
...
Speed: Unknown!
Duplex: Unknown! (255)
$ ethtool -s eth1 speed 1000 duplex full
$ ethtool eth1
Settings for eth1:
...
Speed: 1000Mb/s
Duplex: Full
Based on a patch by Roopa Prabhu.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Wed, 3 Feb 2016 03:04:36 +0000 (04:04 +0100)]
ethtool: add speed/duplex validation functions
Add functions which check if the speed/duplex are defined.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 7 Feb 2016 19:13:12 +0000 (14:13 -0500)]
Merge branch 'sunvnet-tracepoints'
Sowmini Varadhan says:
====================
sunvnet: perf tracepoint hooks
Added some perf tracepoints to help track and debug sunvnet
descriptor state at run-time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Tue, 2 Feb 2016 18:41:56 +0000 (10:41 -0800)]
sunvnet: perf tracepoint invocations to trace LDC state machine
Use sunvnet perf trace macros to monitor LDC message exchange state.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Tue, 2 Feb 2016 18:41:55 +0000 (10:41 -0800)]
sunvnet: Add support for perf LDC event tracing
Add perf event macros for support of tracing and instrumentation
of LDC state machine
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 7 Feb 2016 19:09:59 +0000 (14:09 -0500)]
Merge branch 'tcp_cong_ctrl_refactoring'
Yuchung Cheng says:
====================
tcp: congestion control refactoring
This patch set refactors the sequence of congestion control,
loss recovery, and transmission logic in TCP ack processing.
The design goal is to decouple and sequence them in the following order:
0. ACK accounting: free or tag sent packets [unchanged]
1. loss recovery: identify lost/ecn packets and update congestion state
2. congestion control: up/down cwnd and pacing rate based on (1)
3. transmission: send new or retransmit old based on (1) and (2)
This refactoring makes the cwnd changes more clear because it's done
in one place. The packet accounting is also more robust especially
for connections that do not support SACK. Patch 1-4 and 6 are
refactoring and patch 5 improves TCP performance under reordering.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Tue, 2 Feb 2016 18:33:09 +0000 (10:33 -0800)]
tcp: tcp_cong_control helper
Refactor and consolidate cwnd and rate updates into a new function
tcp_cong_control().
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Tue, 2 Feb 2016 18:33:08 +0000 (10:33 -0800)]
tcp: make congestion control more robust against reordering
This change enables congestion control to update cwnd based on
not only packet cumulatively acked but also packets delivered
out-of-order. This makes congestion control robust against packet
reordering because it may raise cwnd as long as packets are being
delivered once reordering has been detected (i.e., it only cares
the amount of packets delivered, not the ordering among them).
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Tue, 2 Feb 2016 18:33:07 +0000 (10:33 -0800)]
tcp: refactor pkts acked accounting
A small refactoring that gets number of packets cumulatively acked
from tcp_clean_rtx_queue() directly.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>