OSDN Git Service
Linus Torvalds [Fri, 24 Dec 2010 21:00:16 +0000 (13:00 -0800)]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: issue DIPM enable commands with LPM state updated
libata: no special completion processing for EH commands
pata_mpc52xx: driver needs BMDMA
pata_cs5536: Add support for non-X86_32 platforms
libata-sff: fix HSM_ST_ERR handling in __ata_sff_port_intr()
Linus Torvalds [Fri, 24 Dec 2010 20:59:09 +0000 (12:59 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tj/percpu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: print out alloc information with KERN_DEBUG instead of KERN_INFO
kthread_work: make lockdep happy
Linus Torvalds [Fri, 24 Dec 2010 20:58:43 +0000 (12:58 -0800)]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] fix up documentation for change in ->queuecommand to lockless calling
[SCSI] bfa: rename log_level to bfa_log_level
Tejun Heo [Thu, 9 Dec 2010 15:13:15 +0000 (16:13 +0100)]
libata: issue DIPM enable commands with LPM state updated
Low level drivers may behave differently depending on the current
link->lpm_policy. During ata_eh_set_lpm(), DIPM enable commands are
issued after the successful completion of ap->ops->set_lpm(), which
means that the controller is already in the target state. This causes
DIPM enable commands to be processed with mismatching controller power
state and link->lpm_policy value.
In ahci, link->lpm_policy is used to ignore certain PHY events if LPM
is enabled; however, as DIPM commands are issued with stale
link->lpm_policy, they sometimes end up triggering these conditions
and get aborted leading to LPM configuration failure.
Fix it by updating link->lpm_policy before issuing DIPM enable
commands.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Thu, 9 Dec 2010 14:59:32 +0000 (15:59 +0100)]
libata: no special completion processing for EH commands
ata_qc_complete() contains special handling for certain commands. For
example, it schedules EH for device revalidation after certain
configurations are changed. These shouldn't be applied to EH
commands but they were.
In most cases, it doesn't cause an actual problem because EH doesn't
issue any command which would trigger special handling; however, ACPI
can issue such commands via _GTF which can cause weird interactions.
Restructure ata_qc_complete() such that EH commands are always passed
on to __ata_qc_complete().
stable: Please apply to -stable only after 2.6.38 is released.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Wolfram Sang [Wed, 22 Dec 2010 15:50:10 +0000 (16:50 +0100)]
pata_mpc52xx: driver needs BMDMA
Found by this build-error if BMDMA is disabled:
drivers/ata/pata_mpc52xx.c: In function 'mpc52xx_ata_init_one':
drivers/ata/pata_mpc52xx.c:662: error: 'ata_bmdma_interrupt' undeclared (first use in this function)
...
Move the Kconfig entry to the proper location as needed since
9a7780c9acb821fe1c2b6fc53f74cc2556ff5364 (libata-sff: make BMDMA optional)
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Wu Zhangjin [Fri, 24 Dec 2010 13:39:08 +0000 (21:39 +0800)]
pata_cs5536: Add support for non-X86_32 platforms
pata_cs5536 does work on the other platforms(e.g. Loongson, a MIPS
variant), so, remove the dependency of X86_32 and fix the building
errors under the other platforms via only reserving the X86_32 specific
parts for X86_32.
pata_amd also supports cs5536 IDE controller, but this one saves about
33k for the compressed kernel image(vmlinuz for MIPS).
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Chen Jie <chenj@lemote.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Fri, 3 Dec 2010 14:19:13 +0000 (15:19 +0100)]
libata-sff: fix HSM_ST_ERR handling in __ata_sff_port_intr()
While separating out BMDMA irq handler from SFF, commit
c3b28894
(libata-sff: separate out BMDMA irq handler) incorrectly made
__ata_sff_port_intr() consider an IRQ to be an idle one if the host
state was transitioned to HSM_ST_ERR by ata_bmdma_port_intr().
This makes BMDMA drivers ignore IRQs reporting host bus error which
leads to timeouts instead of triggering EH immediately. Fix it by
making __ata_sff_port_intr() consider the IRQ to be an idle one iff
the state is HSM_ST_IDLE. This is equivalent to adding HSM_ST_ERR to
the "break"ing case but less error-prone.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Antonio Toma <antonio.toma@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Linus Torvalds [Fri, 24 Dec 2010 00:36:48 +0000 (16:36 -0800)]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jlbec/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2: Fix system inodes cache overflow.
ocfs2: Hold ip_lock when set/clear flags for indexed dir.
ocfs2: Adjust masklog flag values
Ocfs2: Teach 'coherency=full' O_DIRECT writes to correctly up_read i_alloc_sem.
ocfs2/dlm: Migrate lockres with no locks if it has a reference
Linus Torvalds [Fri, 24 Dec 2010 00:25:31 +0000 (16:25 -0800)]
Merge branch 'linus-hot-fix' of git://git./linux/kernel/git/tytso/ext4
* 'linus-hot-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix on-line resizing regression
Linus Torvalds [Fri, 24 Dec 2010 00:04:32 +0000 (16:04 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix GPIO2-fixup for Sony laptops
ALSA: hda - Try to find an empty control index when it's occupied
ALSA: hda - Fix conflict of d-mic capture volume controls
ALSA: hda - Don't apply ALC269-specific initialization to ALC275
ALSA: hda - Add fix-up for Sony VAIO with ALC275 codecs
ALSA: pcm: remember to always call va_end() on stuff that we va_start()
ALSA: HDA: Add auto-mute for Thinkpad SL410/SL510
Linus Torvalds [Thu, 23 Dec 2010 23:59:23 +0000 (15:59 -0800)]
Merge branch 'v4l_for_linus' of git://git./linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (21 commits)
[media] mceusb: set a default rx timeout
[media] mceusb: fix inverted mask inversion logic
[media] mceusb: add another Fintek device ID
[media] lirc_dev: fixes in lirc_dev_fop_read()
[media] lirc_dev: stray unlock in lirc_dev_fop_poll()
[media] rc: fix sysfs entry for mceusb and streamzap
[media] streamzap: merge timeout space with trailing space
[media] mceusb: fix keybouce issue after parser simplification
[media] IR: add tv power scancode to rc6 mce keymap
[media] mceusb: buffer parsing fixups for 1st-gen device
[media] mceusb: fix up reporting of trailing space
[media] nuvoton-cir: improve buffer parsing responsiveness
[media] mceusb: add support for Conexant Hybrid TV RDU253S
[media] s5p-fimc: Fix output DMA handling in S5PV310 IP revisions
[media] s5p-fimc: Use correct fourcc code for 32-bit RGB format
[media] s5p-fimc: Convert m2m driver to unlocked_ioctl
[media] s5p-fimc: Explicitly add required header file
[media] s5p-fimc: Fix vidioc_g_crop/cropcap on camera sensor
[media] s5p-fimc: BKL lock removal - compilation fix
[media] soc-camera: fix static build of the sh_mobile_csi2.c driver
...
Linus Torvalds [Thu, 23 Dec 2010 23:39:40 +0000 (15:39 -0800)]
Merge branches 'perf-fixes-for-linus' and 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf probe: Fix to support libdwfl older than 0.148
perf tools: Fix lazy wildcard matching
perf buildid-list: Fix error return for success
perf buildid-cache: Fix symbolic link handling
perf symbols: Stop using vmlinux files with no symbols
perf probe: Fix use of kernel image path given by 'k' option
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, kexec: Limit the crashkernel address appropriately
David Howells [Wed, 22 Dec 2010 16:24:13 +0000 (16:24 +0000)]
KEYS: Don't call up_write() if __key_link_begin() returns an error
In construct_alloc_key(), up_write() is called in the error path if
__key_link_begin() fails, but this is incorrect as __key_link_begin() only
returns with the nominated keyring locked if it returns successfully.
Without this patch, you might see the following in dmesg:
=====================================
[ BUG: bad unlock balance detected! ]
-------------------------------------
mount.cifs/5769 is trying to release lock (&key->sem) at:
[<
ffffffff81201159>] request_key_and_link+0x263/0x3fc
but there are no more locks to release!
other info that might help us debug this:
3 locks held by mount.cifs/5769:
#0: (&type->s_umount_key#41/1){+.+.+.}, at: [<
ffffffff81131321>] sget+0x278/0x3e7
#1: (&ret_buf->session_mutex){+.+.+.}, at: [<
ffffffffa0258e59>] cifs_get_smb_ses+0x35a/0x443 [cifs]
#2: (root_key_user.cons_lock){+.+.+.}, at: [<
ffffffff81201000>] request_key_and_link+0x10a/0x3fc
stack backtrace:
Pid: 5769, comm: mount.cifs Not tainted 2.6.37-rc6+ #1
Call Trace:
[<
ffffffff81201159>] ? request_key_and_link+0x263/0x3fc
[<
ffffffff81081601>] print_unlock_inbalance_bug+0xca/0xd5
[<
ffffffff81083248>] lock_release_non_nested+0xc1/0x263
[<
ffffffff81201159>] ? request_key_and_link+0x263/0x3fc
[<
ffffffff81201159>] ? request_key_and_link+0x263/0x3fc
[<
ffffffff81083567>] lock_release+0x17d/0x1a4
[<
ffffffff81073f45>] up_write+0x23/0x3b
[<
ffffffff81201159>] request_key_and_link+0x263/0x3fc
[<
ffffffffa026fe9e>] ? cifs_get_spnego_key+0x61/0x21f [cifs]
[<
ffffffff812013c5>] request_key+0x41/0x74
[<
ffffffffa027003d>] cifs_get_spnego_key+0x200/0x21f [cifs]
[<
ffffffffa026e296>] CIFS_SessSetup+0x55d/0x1273 [cifs]
[<
ffffffffa02589e1>] cifs_setup_session+0x90/0x1ae [cifs]
[<
ffffffffa0258e7e>] cifs_get_smb_ses+0x37f/0x443 [cifs]
[<
ffffffffa025a9e3>] cifs_mount+0x1aa1/0x23f3 [cifs]
[<
ffffffff8111fd94>] ? alloc_debug_processing+0xdb/0x120
[<
ffffffffa027002c>] ? cifs_get_spnego_key+0x1ef/0x21f [cifs]
[<
ffffffffa024cc71>] cifs_do_mount+0x165/0x2b3 [cifs]
[<
ffffffff81130e72>] vfs_kern_mount+0xaf/0x1dc
[<
ffffffff81131007>] do_kern_mount+0x4d/0xef
[<
ffffffff811483b9>] do_mount+0x6f4/0x733
[<
ffffffff8114861f>] sys_mount+0x88/0xc2
[<
ffffffff8100ac42>] system_call_fastpath+0x16/0x1b
Reported-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andres Salomon [Tue, 21 Dec 2010 21:04:52 +0000 (13:04 -0800)]
cs5535-gpio: handle GPIO regs where higher (clear) bits are set
The default for non-READ_BACK GPIO regs is to have the clear bits set;
this means that our original errata fix was too simplistic. This
changes it to the following behavior:
- when setting GPIOs, ignore the higher order bits (they're for
clearing, we don't need to care about them).
- when clearing GPIOs, keep all the bits, but unset (via XOR) the
lower order bit that negates the clear bit that we care about. That
is, if we're clearing GPIO 26 (val = 0x04000000), we first XOR what's
currently in the register with 0x0400 (GPIO 26's SET bit), and then
OR that with the GPIO 26's CLEAR bit.
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andres Salomon [Tue, 21 Dec 2010 21:04:42 +0000 (13:04 -0800)]
cs5535-gpio: don't apply errata #36 to edge detect GPIOs
The edge detect status GPIOs function differently from the other atomic
model CS5536 GPIO registers; writing 1 to the high bits clears the GPIO,
but writing 1 to the lower bits also clears the bit.
This means that read-modify-write doesn't actually work for it, so don't
apply the errata here. If a negative edge status gets lost after
resume.. well, we tried our best!
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Theodore Ts'o [Tue, 21 Dec 2010 03:30:36 +0000 (22:30 -0500)]
ext4: fix on-line resizing regression
https://bugzilla.kernel.org/show_bug.cgi?id=25352
This regression was caused by commit
a31437b85: "ext4: use
sb_issue_zeroout in setup_new_group_blocks", by accidentally dropping
the code which reserved the block group descriptor and inode table
blocks.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Takashi Iwai [Thu, 23 Dec 2010 15:37:31 +0000 (16:37 +0100)]
Merge branch 'fix/hda' into for-linus
Takashi Iwai [Thu, 23 Dec 2010 15:35:34 +0000 (16:35 +0100)]
ALSA: hda - Fix GPIO2-fixup for Sony laptops
The fix-up entries by the commit
2785591a9760c677a7ee6f541e751c23086f5bfd
ALSA: hda - Add fix-up for Sony VAIO with ALC275 codecs
weren't applied in the right position. They had to be before the quirk
entry matching to all Sony devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Thu, 23 Dec 2010 09:28:26 +0000 (10:28 +0100)]
Merge branch 'fix/misc' into for-linus
Takashi Iwai [Thu, 23 Dec 2010 09:17:52 +0000 (10:17 +0100)]
ALSA: hda - Try to find an empty control index when it's occupied
When a mixer control element was already created with the given name,
try to find another index for avoiding conflicts, instead of breaking
with an error. This makes the driver more robust.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Thu, 23 Dec 2010 09:16:05 +0000 (10:16 +0100)]
ALSA: hda - Fix conflict of d-mic capture volume controls
When the d-mics are assigned to the same purpose of another analog mic
pins, the driver doesn't compute the index properly, resulting in an
error with "existing control". This patch fixes it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Thu, 23 Dec 2010 03:47:37 +0000 (19:47 -0800)]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Include the connector name in the output_poll_execute() debug message
drm/radeon/kms: fix bug in r600_gpu_is_lockup
drm/radeon/kms: reorder display resume to avoid problems
drm/radeon/kms/evergreen: reset the grbm blocks at resume and init
drm/radeon/kms: fix evergreen asic reset
Revert "drm: Don't try and disable an encoder that was never enabled"
drm/radeon: Add early unregister of firmware fb's
drm/radeon: use aperture size not vram size for overlap tests
drm/radeon/kms/evergreen: flush hdp cache when flushing gart tlb
drm/radeon/kms: disable the r600 cb offset checker for linear surfaces
drm/radeon/kms: disable ss fixed ref divide
drm/i915/bios: Reverse order of 100/120 Mhz SSC clocks
agp/intel: Fix missed cached memory flags setting in i965_write_entry()
drm/i915/sdvo: Only use the SDVO pin if it is in the valid range
drm/i915/ringbuffer: Handle wrapping of the autoreported HEAD
drm/i915/dp: Fix I2C/EDID handling with active DisplayPort to DVI converter
Linus Torvalds [Thu, 23 Dec 2010 03:47:04 +0000 (19:47 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sameo/mfd-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Support additional parent IDs for wm831x
mfd: Fix ab8500-core interrupt ffs bit bug
mfd: Supply IRQ base for WM832x devices
watchdog: Fix null pointer dereference while accessing rdc321x platform_data
gpio: Fix null pointer dereference while accessing rdc321x platform_data
Sebastian Andrzej Siewior [Wed, 22 Dec 2010 01:24:31 +0000 (17:24 -0800)]
drivers/spi/spi.c: don't release the spi device twice
This was fixed by David Lamparter in v2.6.36-rc5
3486008 ("spi: free
children in spi_unregister_master, not siblings") and broken again in
v2.6.37-rc1~2^2~4 during the merge of
2b9603a0 ("spi: enable
spi_board_info to be registered after spi_master").
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Lamparter <equinox@diac24.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Mahoney [Wed, 22 Dec 2010 01:24:30 +0000 (17:24 -0800)]
taskstats: pad taskstats netlink response for aligment issues on ia64
The taskstats structure is internally aligned on 8 byte boundaries but the
layout of the aggregrate reply, with two NLA headers and the pid (each 4
bytes), actually force the entire structure to be unaligned. This causes
the kernel to issue unaligned access warnings on some architectures like
ia64. Unfortunately, some software out there doesn't properly unroll the
NLA packet and assumes that the start of the taskstats structure will
always be 20 bytes from the start of the netlink payload. Aligning the
start of the taskstats structure breaks this software, which we don't
want. So, for now the alignment only happens on architectures that
require it and those users will have to update to fixed versions of those
packages. Space is reserved in the packet only when needed. This ifdef
should be removed in several years e.g. 2012 once we can be confident
that fixed versions are installed on most systems. We add the padding
before the aggregate since the aggregate is already a defined type.
Commit
85893120 ("delayacct: align to 8 byte boundary on 64-bit systems")
previously addressed the alignment issues by padding out the pid field.
This was supposed to be a compatible change but the circumstances
described above mean that it wasn't. This patch backs out that change,
since it was a hack, and introduces a new NULL attribute type to provide
the padding. Padding the response with 4 bytes avoids allocating an
aligned taskstats structure and copying it back. Since the structure
weighs in at 328 bytes, it's too big to do it on the stack.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reported-by: Brian Rogers <brian@xyzw.org>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Guillaume Chazarain <guichaz@gmail.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Will Newton [Wed, 22 Dec 2010 01:24:29 +0000 (17:24 -0800)]
include/linux/unaligned: pack the whole struct rather than just the field
The current packed struct implementation of unaligned access adds the
packed attribute only to the field within the unaligned struct rather than
to the struct as a whole. This is not sufficient to enforce proper
behaviour on architectures with a default struct alignment of more than
one byte.
For example, the current implementation of __get_unaligned_cpu16 when
compiled for arm with gcc -O1 -mstructure-size-boundary=32 assumes the
struct is on a 4 byte boundary so performs the load of the 16bit packed
field as if it were on a 4 byte boundary:
__get_unaligned_cpu16:
ldrh r0, [r0, #0]
bx lr
Moving the packed attribute to the struct rather than the field causes the
proper unaligned access code to be generated:
__get_unaligned_cpu16:
ldrb r3, [r0, #0] @ zero_extendqisi2
ldrb r0, [r0, #1] @ zero_extendqisi2
orr r0, r3, r0, asl #8
bx lr
Signed-off-by: Will Newton <will.newton@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Wed, 22 Dec 2010 01:24:28 +0000 (17:24 -0800)]
led_class: fix typo in blink API
When I added led_blink_set I had a typo: the return value of the hw
offload is a regular error code that is zero when succesful, and in that
case software emulation should not be used, rather than the other way
around.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Axel Lin [Wed, 22 Dec 2010 01:24:27 +0000 (17:24 -0800)]
backlight: cr_bllcd.c: fix a memory leak
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Thomas Hellstrom <thomas@tungstengraphics.com>
Cc: Alan Hourihane <alanh@tungstengraphics.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Nazarewicz [Wed, 22 Dec 2010 01:24:26 +0000 (17:24 -0800)]
mm/migrate.c: fix compilation error
GCC complained about update_mmu_cache() not being defined in migrate.c.
Including <asm/tlbflush.h> seems to solve the problem.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wolfram Sang [Wed, 22 Dec 2010 01:24:24 +0000 (17:24 -0800)]
rtc: rs5c372: fix buffer size
Match the buffer size to the amount of initialized values. Before, it was
one too big and thus destroyed the neighbouring register causing the clock
to run at false speeds.
Reported-by: Andre van Rooyen <a.v.rooyen@sercom.nl>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andres Salomon [Wed, 22 Dec 2010 01:24:23 +0000 (17:24 -0800)]
MAINTAINERS: update geode entry
Remove Jordan as the geode maintainer (he's not been interested in geode for
some time), and add myself as the maintainer.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Cc: Daniel Drake <dsd@laptop.org>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aaro Koskinen [Wed, 22 Dec 2010 01:24:22 +0000 (17:24 -0800)]
gpiolib: gpio_request_one(): add missing gpio_free()
If GPIO request succeeds, but configuration fails, it should be released.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wu Fengguang [Wed, 22 Dec 2010 01:24:21 +0000 (17:24 -0800)]
writeback: do uninterruptible sleep in balance_dirty_pages()
Using TASK_INTERRUPTIBLE in balance_dirty_pages() seems wrong. If it's
going to do that then it must break out if signal_pending(), otherwise
it's pretty much guaranteed to degenerate into a busywait loop. Plus we
*do* want these processes to appear in D state and to contribute to load
average.
So it should be TASK_UNINTERRUPTIBLE. -- Andrew Morton
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prasad Joshi [Wed, 22 Dec 2010 01:24:20 +0000 (17:24 -0800)]
logfs: fix "Kernel BUG at readwrite.c:1193"
This happens when __logfs_create() tries to write a new inode to the disk
which is full.
__logfs_create() associates the transaction pointer with inode. During
the logfs_write_inode() function call chain this transaction pointer is
moved from inode to page->private using function move_inode_to_page
(do_write_inode() -> inode_to_page() -> move_inode_to_page)
When the write inode fails, the transaction is aborted and iput is called
on the failed inode. During delete_inode the same transaction pointer
associated with the page is getting used. Thus causing kernel BUG.
The patch checks for error in write_inode() and restores the page->private
to NULL.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=20162
Signed-off-by: Prasad Joshi <prasadjoshi124@gmail.com>
Cc: Joern Engel <joern@logfs.org>
Cc: Florian Mickler <florian@mickler.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prasad Joshi [Wed, 22 Dec 2010 01:24:19 +0000 (17:24 -0800)]
logfs: fix deadlock in logfs_get_wblocks, hold and wait on super->s_write_mutex
do_logfs_journal_wl_pass() should use GFP_NOFS for memory allocation GC
code calls btree_insert32 with GFP_KERNEL while holding a mutex
super->s_write_mutex.
The same mutex is used in address_space_operations->writepage(), and a
call to writepage() could be triggered as a result of memory allocation
in btree_insert32, causing a deadlock.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=20342
Signed-off-by: Prasad Joshi <prasadjoshi124@gmail.com>
Cc: Joern Engel <joern@logfs.org>
Cc: Florian Mickler <florian@mickler.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Wed, 22 Dec 2010 01:24:18 +0000 (17:24 -0800)]
mm: vmscan: tracepoint: account for scanned pages similarly for both ftrace and vmstat
When correlating ftrace results with /proc/vmstat, I noticed that the
reporting scripts value for "pages scanned" differed significantly. Both
values were "right" depending on how you look at it.
The difference is due to vmstat only counting scanning of the inactive
list towards pages scanned. The analysis script for the tracepoint counts
active and inactive list yielding a far higher value than vmstat. The
resulting scanning/reclaim ratio looks much worse. The tracepoint is ok
but this patch updates the reporting script so that the report values for
scanned are similar to vmstat.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minchan Kim [Wed, 22 Dec 2010 01:24:16 +0000 (17:24 -0800)]
mm/compaction.c: avoid double mem_cgroup_del_lru()
del_page_from_lru_list() already called mem_cgroup_del_lru(). So we must
not call it again. It adds unnecessary overhead.
It was not a runtime bug because the TestClearPageCgroupAcctLRU() early in
mem_cgroup_del_lru_list() will prevent any double-deletion, etc.
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tejun Heo [Wed, 22 Dec 2010 13:19:14 +0000 (14:19 +0100)]
percpu: print out alloc information with KERN_DEBUG instead of KERN_INFO
Now that percpu allocator is mostly stable, there is no reason to
print alloc information with KERN_INFO and clutter the boot messages.
Switch it to KERN_DEBUG.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Travis <travis@sgi.com>
Mark Brown [Thu, 2 Dec 2010 16:25:43 +0000 (16:25 +0000)]
mfd: Support additional parent IDs for wm831x
Some newer device revisions add a second parent ID. Support this in
the device validity checks done at startup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mattias Wallin [Thu, 2 Dec 2010 14:06:49 +0000 (15:06 +0100)]
mfd: Fix ab8500-core interrupt ffs bit bug
We want to find the first set bit on value, not status.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Wed, 24 Nov 2010 18:01:39 +0000 (18:01 +0000)]
mfd: Supply IRQ base for WM832x devices
Without this the IRQ base will not be correctly configured for the
subdevices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Florian Fainelli [Fri, 26 Nov 2010 09:39:55 +0000 (10:39 +0100)]
watchdog: Fix null pointer dereference while accessing rdc321x platform_data
rdc321x-wdt currently fetches its driver specific data by using the
platform_device->platform_data pointer, this is wrong because the mfd
device which registers our platform_device has been added using
mfd_add_device() which sets the platform_device->driver_data pointer
instead.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Florian Fainelli [Fri, 26 Nov 2010 09:39:54 +0000 (10:39 +0100)]
gpio: Fix null pointer dereference while accessing rdc321x platform_data
rdc321x-gpio currently fetches its driver specific data by using the
platform_device->platform_data pointer, this is wrong because the mfd
device which registers our platform_device has been added using
mfd_add_device() which sets the platform_device->driver_data pointer
instead.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Tao Ma [Wed, 22 Dec 2010 09:50:30 +0000 (17:50 +0800)]
ocfs2: Fix system inodes cache overflow.
When we store system inodes cache in ocfs2_super,
we use a array for global system inodes. But unfortunately,
the range is calculated wrongly which makes it overflow and
pollute ocfs2_super->local_system_inodes.
This patch fix it by setting the range properly.
The corresponding bug is ossbug1303.
http://oss.oracle.com/bugzilla/show_bug.cgi?id=1303
Cc: stable@kernel.org
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Ingo Molnar [Wed, 22 Dec 2010 10:31:03 +0000 (11:31 +0100)]
Merge branch 'perf/urgent' of git://git./linux/kernel/git/acme/linux-2.6 into perf/urgent
Yong Zhang [Wed, 22 Dec 2010 09:27:53 +0000 (10:27 +0100)]
kthread_work: make lockdep happy
spinlock in kthread_worker and wait_queue_head in kthread_work both
should be lockdep sensible, so change the interface to make it
suiltable for CONFIG_LOCKDEP.
tj: comment update
Reported-by: Nicolas <nicolas.mailhot@laposte.net>
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Tested-by: Andy Walls <awalls@md.metrocast.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Chris Wilson [Tue, 21 Dec 2010 22:49:28 +0000 (22:49 +0000)]
drm: Include the connector name in the output_poll_execute() debug message
Always useful to know just which connector was polled and had its
status updated.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Tue, 21 Dec 2010 21:05:38 +0000 (16:05 -0500)]
drm/radeon/kms: fix bug in r600_gpu_is_lockup
We were using the lockup struct from the wrong union.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Masami Hiramatsu [Fri, 17 Dec 2010 13:12:18 +0000 (22:12 +0900)]
perf probe: Fix to support libdwfl older than 0.148
Since the libdwfl library before 0.148 fails to analyze live kernel debuginfo,
'perf probe --list' compiled with those old libdwfl sometimes crashes.
To avoid that bug, perf probe does not use libdwfl's live kernel analysis
routine when it is compiled with older libdwfl.
Side effect: perf with older libdwfl doesn't support listing probe in modules
with source code line. Those could be shown by symbol+offset.
Cc: 2nddept-manager@sdl.hitachi.co.jp
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <
20101217131218.24123.62424.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Masami Hiramatsu [Fri, 17 Dec 2010 13:12:00 +0000 (22:12 +0900)]
perf tools: Fix lazy wildcard matching
Fix lazy wildcard matching to ignore space after wild card.
Cc: 2nddept-manager@sdl.hitachi.co.jp
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <
20101217131200.24123.8202.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Linus Torvalds [Tue, 21 Dec 2010 19:26:40 +0000 (11:26 -0800)]
Linux 2.6.37-rc7
James Bottomley [Thu, 16 Dec 2010 14:22:24 +0000 (09:22 -0500)]
[SCSI] fix up documentation for change in ->queuecommand to lockless calling
The current doc still says we call it with the host lock held, which is
going to cause confusion.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kailang Yang [Tue, 21 Dec 2010 08:14:13 +0000 (09:14 +0100)]
ALSA: hda - Don't apply ALC269-specific initialization to ALC275
ALC275 doesn't require the ALC269 (and its variants) specific init
sequences. Add the check of codec id.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kailang Yang [Tue, 21 Dec 2010 08:09:53 +0000 (09:09 +0100)]
ALSA: hda - Add fix-up for Sony VAIO with ALC275 codecs
Set GPIO2 for some Sony VAIO with ALC275 to fix speaker output.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jesper Juhl [Mon, 20 Dec 2010 23:03:17 +0000 (00:03 +0100)]
ALSA: pcm: remember to always call va_end() on stuff that we va_start()
The Coverity checker spotted that we do not always remember to call
va_end() on 'args' in failure paths in snd_pcm_hw_rule_add().
Here's a patch to fix that up (compile tested only) - it also removes
some annoying trailing whitespace that caught my eye while I was in the
area..
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Tue, 21 Dec 2010 05:34:16 +0000 (21:34 -0800)]
Merge branch 'tty-linus' of git://git./linux/kernel/git/gregkh/tty-2.6
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
n_gsm: gsm_data_alloc buffer allocation could fail and it is not being checked
n_gsm: Fix message length handling when building header
Linus Torvalds [Tue, 21 Dec 2010 05:33:12 +0000 (21:33 -0800)]
Merge branch 'usb-linus' of git://git./linux/kernel/git/gregkh/usb-2.6
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
Revert "USB: gadget: Allow function access to device ID data during bind()"
USB: misc: uss720.c: add another vendor/product ID
USB: usb-storage: unusual_devs entry for the Samsung YP-CP3
USB: gadget: Remove suspended sysfs file before freeing cdev
USB: core: Add input prompt and help text for USB_OTG config
USB: ftdi_sio: Add D.O.Tec PID
xhci: Fix issue with port array setup and buggy hosts.
Linus Torvalds [Tue, 21 Dec 2010 05:32:20 +0000 (21:32 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: handle partial result from get_user_pages
ceph: mark user pages dirty on direct-io reads
ceph: fix null pointer dereference in ceph_init_dentry for nfs reexport
ceph: fix direct-io on non-page-aligned buffers
ceph: fix msgr_init error path
Linus Torvalds [Tue, 21 Dec 2010 05:21:49 +0000 (21:21 -0800)]
Fix build error in drivers/block/cciss.c
.. caused by a missing semi-colon, introduced in commit
0fc13c8995cd
("cciss: fix cciss_revalidate panic").
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Thiago Farina <tfransosi@gmail.com>
Cc: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alex Deucher [Mon, 20 Dec 2010 16:22:29 +0000 (11:22 -0500)]
drm/radeon/kms: reorder display resume to avoid problems
On resume, we were attemping to unblank the displays before the
timing and plls had be reprogrammed which led to atom timeouts
waiting for things that are not yet programmed. Re-program
the mode first, then reset the dpms state.
This fixes the infamous atombios timeouts on resume.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Mon, 20 Dec 2010 17:35:04 +0000 (12:35 -0500)]
drm/radeon/kms/evergreen: reset the grbm blocks at resume and init
This fixes module reloading and resume as the gfx block seems to
be left in a bad state in some cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Mon, 20 Dec 2010 17:35:03 +0000 (12:35 -0500)]
drm/radeon/kms: fix evergreen asic reset
Only reset the grbm blocks, srbm tends to lock the GPU
if not done properly and in most cases is not necessary.
Also, no need to call asic init after reset the grbm blocks.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Tue, 21 Dec 2010 02:47:56 +0000 (12:47 +1000)]
Revert "drm: Don't try and disable an encoder that was never enabled"
This reverts commit
541cc966915b6756e54c20eebe60ae957afdb537.
Wei Yonjun reported this caused a regression against Intel VGA hotplug
on his G33 hw.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Benjamin Herrenschmidt [Wed, 6 Oct 2010 16:39:07 +0000 (16:39 +0000)]
drm/radeon: Add early unregister of firmware fb's
Without this, we attempt the handover too late, the firmware fb
might be accessing the chip simultaneously to us re-initializing
various parts of it, which might frighten babies or cause all sort
of nasty psychologic trauma to kitten.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[danvet: add cc: stable, forward ported and compile-fixed for X86]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[airlied: move to even earlier in module load.]
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Mon, 20 Dec 2010 18:35:04 +0000 (10:35 -0800)]
Merge branch 'v4l_for_linus' of git://git./linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] gspca - sonixj: Better handling of the bridge registers 0x01 and 0x17
[media] gspca - sonixj: Add the bit definitions of the bridge reg 0x01 and 0x17
[media] gspca - sonixj: Set the flag for some devices
[media] gspca - sonixj: Add a flag in the driver_info table
[media] gspca - sonixj: Fix a bad probe exchange
[media] gspca - sonixj: Move bridge init to sd start
[media] bttv: remove unneeded locking comments
[media] bttv: fix mutex use before init (BZ#24602)
[media] Don't export format_by_forcc on two different drivers
Jing Huang [Fri, 10 Dec 2010 01:11:53 +0000 (17:11 -0800)]
[SCSI] bfa: rename log_level to bfa_log_level
Rename log_level to bfa_log_level to make the global variable more bfa
specific and avoid clashes with other drivers which was causing a
build failure.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Linus Torvalds [Mon, 20 Dec 2010 17:59:08 +0000 (09:59 -0800)]
Merge branch 'rmobile-fixes-for-linus' of git://git./linux/kernel/git/lethal/sh-2.6
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: mach-shmobile: INTC interrupt priority level demux fix
ARM: mach-shmobile: fix compile warning in mm/init.c
Linus Torvalds [Mon, 20 Dec 2010 17:53:50 +0000 (09:53 -0800)]
Merge branch 'sh-fixes-for-linus' of git://git./linux/kernel/git/lethal/sh-2.6
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
clocksource: sh_cmt: Remove nested spinlock fix
Linus Torvalds [Mon, 20 Dec 2010 17:49:54 +0000 (09:49 -0800)]
Merge branch 'fbdev-fixes-for-linus' of git://git./linux/kernel/git/lethal/fbdev-2.6
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
OMAP: OMAPFB: disable old omapfb for OMAP4 builds
OMAP: DSS: VRAM: Align start & size of vram to 2M
Linus Torvalds [Mon, 20 Dec 2010 17:46:46 +0000 (09:46 -0800)]
Merge branch 's5p-fixes-for-linus' of git://git./linux/kernel/git/kgene/linux-samsung
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S5PV210: update MAX8998 platform data to get rid of WARN()
ARM S3C24XX: Fix compilation of PM code for S3C2416
ARM: S3C24XX: Fix CONFIG_S3C_DEV_NAND Kconfig entry
Linus Torvalds [Mon, 20 Dec 2010 17:19:46 +0000 (09:19 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: fix cciss_revalidate panic
block: max hardware sectors limit wrapper
block: Deprecate QUEUE_FLAG_CLUSTER and use queue_limits instead
blk-throttle: Correct the placement of smp_rmb()
blk-throttle: Trim/adjust slice_end once a bio has been dispatched
block: check for proper length of iov entries earlier in blk_rq_map_user_iov()
drbd: fix for spin_lock_irqsave in endio callback
drbd: don't recvmsg with zero length
Al Viro [Mon, 20 Dec 2010 15:53:18 +0000 (15:53 +0000)]
Fix btrfs b0rkage
Buggered-in:
76dda93c6ae2 ("Btrfs: add snapshot/subvolume destroy
ioctl")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicolas Pitre [Mon, 20 Dec 2010 05:29:32 +0000 (00:29 -0500)]
clarify a usage constraint for cnt32_to_63()
The cnt32_to_63 algorithm relies on proper counter data evaluation
ordering to work properly. This was missing from the provided
documentation.
Let's augment the documentation with the missing usage constraint and
fix the only instance that got it wrong.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 20 Dec 2010 17:05:26 +0000 (09:05 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Remove debugging check
Jarod Wilson [Thu, 16 Dec 2010 15:40:16 +0000 (12:40 -0300)]
[media] mceusb: set a default rx timeout
Its possible for the call to read rx timeout from the hardware to fail,
in which case we end up with a bogus rx timeout value. Set a default one
when filling in the rc struct, and we'll just overwrite it later w/the
value from hardware, but if that read fails, we've at least got a sane
rx timeout value to work with (1000ms is the default value I've seen
returned on most if not all mceusb hardware).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Wed, 15 Dec 2010 22:20:55 +0000 (19:20 -0300)]
[media] mceusb: fix inverted mask inversion logic
As it turns out, somewhere along the way, we managed to invert the
meaning of the tx_mask_inverted flag. Looking back over the old lirc
driver, tx_mask_inverted was set to 0 if the device was in tx_mask_list.
Now we have a tx_mask_inverted flag set to 1 for all the devices that
were in the list, and set tx_mask_inverted to that flag value, which is
actually the opposite of what we used to set, causing set_tx_mask to use
the wrong mask setting option. Since there seem to be more devices with
inverted masks than not (using the original device as the baseline for
inverted vs. normal), lets just call the ones currently marked as
inverted normal instead, and flip the if/else actions that key off of
the inverted flag.
Note: the problem only cropped up if a call to set_tx_mask was made, if
no mask was set, the device would work just fine, which is why this
managed to slip though w/o getting noticed until now.
Tested successfully by myself and Dennis Gilmore.
Reported-by: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Thu, 16 Dec 2010 16:27:11 +0000 (13:27 -0300)]
[media] mceusb: add another Fintek device ID
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dan Carpenter [Wed, 17 Nov 2010 05:20:15 +0000 (02:20 -0300)]
[media] lirc_dev: fixes in lirc_dev_fop_read()
This makes several changes but they're in one function and sort of
related:
"buf" was leaked on error. The leak if we try to read an invalid
length is the main concern because it could be triggered over and
over.
If the copy_to_user() failed, then the original code returned the
number of bytes remaining. read() is supposed to be the opposite way,
where we return the number of bytes copied. I changed it to just return
-EFAULT on errors.
Also I changed the debug output from "-EFAULT" to just "<fail>" because
it isn't -EFAULT necessarily. And since we go though that path if the
length is invalid now, there was another debug print that I removed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dan Carpenter [Wed, 17 Nov 2010 05:12:23 +0000 (02:12 -0300)]
[media] lirc_dev: stray unlock in lirc_dev_fop_poll()
We shouldn't unlock here. I think this was a cut and paste error.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Paul Bender [Thu, 16 Dec 2010 16:23:07 +0000 (13:23 -0300)]
[media] rc: fix sysfs entry for mceusb and streamzap
When trying to create persistent device names for mceusb and streamzap
devices, I noticed that their respective drivers are not creating the rc
device as a child of the USB device. Rather it creates it as virtual
device. As a result, udev cannot use the USB device information to
create persistent device names for event and lirc devices associated
with the rc device. Not having persistent device names makes it more
difficult to make use of the devices in userspace as their names can
change.
Signed-off-by: Paul Bender <pebender@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Wed, 17 Nov 2010 15:25:45 +0000 (12:25 -0300)]
[media] streamzap: merge timeout space with trailing space
There are cases where we get an ending space, and our trailing timeout
space then gets sent right after it, which breaks repeat, at least for
lirc userspace decoding. Merge the two spaces by way of using
ir_raw_event_store_filter, set a timeout value, and we're back to good.
Successfully tested with streamzap and windows mce remotes.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Fri, 12 Nov 2010 22:49:04 +0000 (19:49 -0300)]
[media] mceusb: fix keybouce issue after parser simplification
Something I failed to notice while testing the mceusb RLE buffer
decoding simplification patches was that we were getting an extra event
from the previously pressed key.
As was pointed out to me on irc by Maxim, this is actually due to using
ir_raw_event_store_with_filter without having set up a timeout value.
The hardware has a timeout value we're now reading and storing, which
properly enables the transition to idle in the raw event storage
process, and makes IR decode behave correctly w/o keybounce.
Also remove no-longer-used ir_raw_event struct from mceusb_dev struct
and add as-yet-unused enable flags for carrier reports and learning
mode, which I'll hopefully start wiring up sooner than later. While
looking into that, found evidence that 0x9f 0x15 responses are only
non-zero when the short-range learning sensor is used, so correct the
debug spew message, and then suppress it when using the standard
long-range sensor.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Tue, 9 Nov 2010 21:42:37 +0000 (18:42 -0300)]
[media] IR: add tv power scancode to rc6 mce keymap
And clean up some stray spaces.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Tue, 9 Nov 2010 21:41:46 +0000 (18:41 -0300)]
[media] mceusb: buffer parsing fixups for 1st-gen device
If we pass in an offset, we shouldn't skip 2 bytes. And the first-gen
hardware generates a constant stream of interrupts, always with two
header bytes, and if there's been no IR, with nothing else. Bail from
ir processing without calling ir_handle_raw_event when we get such a
buffer delivered to us.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Tue, 9 Nov 2010 21:41:03 +0000 (18:41 -0300)]
[media] mceusb: fix up reporting of trailing space
We were storing a bunch of spaces at the end of each signal, rather than
a single long space. The in-kernel decoders were actually okay with
this, but lirc isn't. As suggested by David Härdeman, switch to storing
samples using ir_raw_event_store_with_filter, which auto-merges the
consecutive space samples for us. This also allows us to bypass having
to store rawir samples in our device struct, further simplifying the
buffer parsing state machine. Both in-kernel decoders and lirc are happy
again with this change.
Also included in this patch is proper parsing of 0x9f 0x01 commands, the
removal of some magic number usage and some printk spew fixups.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Tue, 9 Nov 2010 21:11:04 +0000 (18:11 -0300)]
[media] nuvoton-cir: improve buffer parsing responsiveness
Rather than waiting for trigger bits, the formula for which was slightly
messy, and apparently, not actually 100% complete for some remotes, just
call ir_raw_event_handle whenever we finish parsing a chunk of data from
the rx fifo, similar to mceusb, as well as whenever we see an 'end of
signal data' 0x80 packet.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Fri, 29 Oct 2010 03:07:39 +0000 (00:07 -0300)]
[media] mceusb: add support for Conexant Hybrid TV RDU253S
Another multi-function Conexant device. Interface 0 is IR, though on
this model, TX isn't wired up at all, so I've mixed in support for
models without TX (and verified that lircd says TX isn't supported when
trying to send w/this device).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sylwester Nawrocki [Thu, 25 Nov 2010 13:49:21 +0000 (10:49 -0300)]
[media] s5p-fimc: Fix output DMA handling in S5PV310 IP revisions
FIMC IP in S5Pv310 series has extended DMA status registers
and some bit fields are marked as reserved comparing to S5PC100/110.
Use correct registers for getting DMA write pointer in each SoC variant
supported by the driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sylwester Nawrocki [Thu, 25 Nov 2010 12:44:48 +0000 (09:44 -0300)]
[media] s5p-fimc: Use correct fourcc code for 32-bit RGB format
Replace V4L2_PIX_FMT_RGB24 code with V4L2_PIX_FMT_RGB32
since the hardware uses 24-bits for actual pixel data but pixels
are 4-byte aligned in memory.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sylwester Nawrocki [Thu, 18 Nov 2010 10:36:34 +0000 (07:36 -0300)]
[media] s5p-fimc: Convert m2m driver to unlocked_ioctl
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sylwester Nawrocki [Mon, 22 Nov 2010 17:49:06 +0000 (14:49 -0300)]
[media] s5p-fimc: Explicitly add required header file
Reported by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sylwester Nawrocki [Thu, 25 Nov 2010 14:01:51 +0000 (11:01 -0300)]
[media] s5p-fimc: Fix vidioc_g_crop/cropcap on camera sensor
Create separate vidioc_g_crop/vidioc_s_crop handlers for capture
video node and so image cropping parameters are properly queried
at FIMC input (image sensor) and not at FIMC output.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sylwester Nawrocki [Tue, 30 Nov 2010 09:23:10 +0000 (06:23 -0300)]
[media] s5p-fimc: BKL lock removal - compilation fix
Adapt to recent videobuf_queue_dma_contig_init signature change.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Guennadi Liakhovetski [Wed, 20 Oct 2010 13:14:57 +0000 (10:14 -0300)]
[media] soc-camera: fix static build of the sh_mobile_csi2.c driver
The test for driver->owner != NULL in sh_mobile_ceu_camera.c is unneeded and it
breaks the static build of sh_mobile_csi2.c. Remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Baruch Siach [Wed, 27 Oct 2010 07:03:52 +0000 (04:03 -0300)]
[media] mx2_camera: fix pixel clock polarity configuration
When SOCAM_PCLK_SAMPLE_FALLING, just leave CSICR1_REDGE unset, otherwise we get
the inverted behaviour.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
David Henningsson [Fri, 17 Dec 2010 19:43:04 +0000 (20:43 +0100)]
ALSA: HDA: Add auto-mute for Thinkpad SL410/SL510
BugLink: http://launchpad.net/bugs/580006
SKU turns off auto-mute for these machines, so ignore the SKU.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dave Airlie [Mon, 20 Dec 2010 00:54:48 +0000 (10:54 +1000)]
drm/radeon: use aperture size not vram size for overlap tests
This fixes a problem where the wrong card conflicts with vesafb in my
x2 system.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Ingo Molnar [Sun, 19 Dec 2010 22:24:27 +0000 (23:24 +0100)]
sched: Remove debugging check
Linus reported that the new warning introduced by commit
f26f9aff6aaf
"Sched: fix skip_clock_update optimization" triggers. The need_resched
flag can be set by other CPUs asynchronously so this debug check is
bogus - remove it.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <AANLkTinJ8hAG1TpyC+CSYPR47p48+1=E7fiC45hMXT_1@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Sun, 19 Dec 2010 18:44:54 +0000 (10:44 -0800)]
Merge branches 'x86-fixes-for-linus' and 'perf-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32: Make sure we can map all of lowmem if we need to
x86, vt-d: Handle previous faults after enabling fault handling
x86: Enable the intr-remap fault handling after local APIC setup
x86, vt-d: Fix the vt-d fault handling irq migration in the x2apic mode
x86, vt-d: Quirk for masking vtd spec errors to platform error handling logic
x86, xsave: Use alloc_bootmem_align() instead of alloc_bootmem()
bootmem: Add alloc_bootmem_align()
x86, gcc-4.6: Use gcc -m options when building vdso
x86: HPET: Chose a paranoid safe value for the ETIME check
x86: io_apic: Avoid unused variable warning when CONFIG_GENERIC_PENDING_IRQ=n
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix off by one in perf_swevent_init()
perf: Fix duplicate events with multiple-pmu vs software events
ftrace: Have recordmcount honor endianness in fn_ELF_R_INFO
scripts/tags.sh: Add magic for trace-events
tracing: Fix panic when lseek() called on "trace" opened for writing