OSDN Git Service
Amit Cohen [Tue, 8 Dec 2020 09:22:44 +0000 (11:22 +0200)]
mlxsw: spectrum_switchdev: Create common function for joining VxLAN to VLAN-aware bridge
The code in mlxsw_sp_bridge_8021q_vxlan_join() can be used also for
802.1ad bridge.
Move the code to function called mlxsw_sp_bridge_vlan_aware_vxlan_join()
and call it from mlxsw_sp_bridge_8021q_vxlan_join() to enable code
reuse.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Tue, 8 Dec 2020 09:22:43 +0000 (11:22 +0200)]
mlxsw: reg: Add support for tunnel port in SPVID register
Add spvid_tport field which indicates if the port is tunnel port.
When spvid_tport is true, local_port field supposed to be tunnel port
type.
It will be used to configure which Ethertype will be used when VLAN is
pushed at ingress for tunnel port.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Tue, 8 Dec 2020 09:22:42 +0000 (11:22 +0200)]
mlxsw: reg: Add Switch Port VLAN Stacking Register
SPVTR register configures the VLAN mode of the port to enable VLAN
stacking.
It will be used to configure VxLAN to push VLAN to the decapsulated packet.
Without this setting, Spectrum-2 overtakes the VLAN tag of decapsulated
packet for bridging.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Tue, 8 Dec 2020 09:22:41 +0000 (11:22 +0200)]
mlxsw: Use one enum for all registers that contain tunnel_port field
Currently SFN, TNUMT and TNPC registers use separate enums for
tunnel_port.
Create one enum with a neutral name and use it.
Remove the enums that are not currently required.
The next patches add two more registers that contain tunnel_port field,
the new enum can be used for them also.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 8 Dec 2020 23:39:01 +0000 (15:39 -0800)]
Merge tag 'mlx5-updates-2020-12-01' of git://git./linux/kernel/git/saeed/linux
mlx5-updates-2020-12-01
mlx5e port TX timestamping support and MISC updates
1) Add support for port TX timestamping, for better PTP accuracy.
Currently in mlx5 HW TX timestamping is done on CQE (TX completion)
generation, which much earlier than when the packet actually goes out to
the wire, in this series Eran implements the option to do timestamping on
the port using a special SQ (Send Queue), such Send Queue will generate 2
CQEs (TX completions), the original one and a new one when the packet
leaves the port, due to the nature of this special handling, such mechanism
is an opt-in only and it is off by default to avoid any performance
degradation on normal traffic flows.
This patchset improves TX Hardware timestamping offset to be less than
40ns at a 100Gbps line rate, compared to 600ns before.
With that, making our HW compliant with G.8273.2 class C, and allow Linux
systems to be deployed in the 5G telco edge, where this standard is a must.
2) Misc updates and trivial improvements.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 8 Dec 2020 19:58:55 +0000 (11:58 -0800)]
Merge branch 'net-hns3-updates-for-next'
Huazhong Tan says:
====================
net: hns3: updates for -next
There are some updates for the HNS3 ethernet driver.
promiscuous configuration more flexible, #2 adds ethtool
private flags to control whether enable tx unicast promisc.
previous version:
https://patchwork.kernel.org/project/netdevbpf/cover/
1606997936-22166-1-git-send-email-tanhuazhong@huawei.com/
====================
Link: https://lore.kernel.org/r/1607227575-56689-1-git-send-email-tanhuazhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guojia Liao [Sun, 6 Dec 2020 04:06:15 +0000 (12:06 +0800)]
net: hns3: refine the VLAN tag handle for port based VLAN
For DEVICE_VERSION_V2, the hardware only supports max two layer
VLAN tags, including port based tag inserted by hardware, tag in
tx buffer descriptor(get from skb->tci) and tag in packet.
For transmit packet:
If port based VLAN disabled, and vf driver gets a VLAN tag from
skb, the VLAN tag must be filled to the Outer_VLAN_TAG field
(tag near to DMAC) of tx buffer descriptor, otherwise it may
be inserted after the tag in packet.
If port based VLAN enabled, and vf driver gets a VLAN tag from
skb, the VLAN tag must be filled to the VLAN_TAG field (tag
far to DMAC) of tx buffer descriptor, otherwise it may be
conflicted with port based VLAN, and raise a hardware error.
For receive packet:
The hardware will strip the VLAN tags and fill them in the rx
buffer descriptor, no matter port based VLAN enable or not.
Because port based VLAN tag is useless for stack, so vf driver
needs to discard the port based VLAN tag get from rx buffer
descriptor when port based VLAN enabled.
So vf must know about the port based VLAN state.
For DEVICE_VERSION_V3, the hardware provides some new
configuration to improve it.
For transmit packet:
When enable tag shift mode, hardware will handle the VLAN tag
in outer_VLAN_TAG field as VLAN_TAG, so it won't conflict with
port based VLAN. And hardware also make sure the tag before
the tag in packet. So vf driver doesn't need to specify the tag
position according to the port based VLAN state anymore.
For receive packet:
When enable discard mode, hardware will strip and discard the
port based VLAN tag, so vf driver doesn't need to identify it
from rx buffer descriptor.
So modify the port based VLAN configuration, simplify the process
for vf handling the VLAN tag.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jian Shen [Sun, 6 Dec 2020 04:06:14 +0000 (12:06 +0800)]
net: hns3: add priv flags support to switch limit promisc mode
Currently, the tx unicast promisc is always enabled when promisc
mode on. If tx unicast promisc on, a function will receive all
unicast packet from other functions belong to the same port.
Add a ethtool private flag to control whether enable tx
unicast promisc. Then the function is able to filter the
unknown unicast packets from other function.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guojia Liao [Sun, 6 Dec 2020 04:06:13 +0000 (12:06 +0800)]
net: hns3: add support for extended promiscuous command
For DEVICE_VERSION_V2, the hardware supports enable tx and rx
promiscuous separately. But tx or rx promiscuous is active for
unicast, multicast and broadcast promiscuous simultaneously.
To support traffics between functions belong to the same port,
we always enable tx promiscuous for broadcast promiscuous, so
tx promiscuous for unicast and multicast promiscuous is also
enabled.
For DEVICE_VERSION_V3, the hardware decouples the above
relationship. Tx unicast promiscuous, rx unicast promiscuous,
tx multicast promiscuous, rx multicast promiscuous, tx broadcast
promiscuous and rx broadcast promiscuous can be enabled separately.
So add support for the new promiscuous command.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Maxim Mikityanskiy [Tue, 1 Dec 2020 22:42:08 +0000 (14:42 -0800)]
net/mlx5e: Fill mlx5e_create_cq_param in a function
Create a function to fill the fields of struct mlx5e_create_cq_param
based on a channel. The purpose is code reuse between normal CQs, XSK
CQs and the upcoming QoS CQs.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Aya Levin [Tue, 1 Dec 2020 22:42:07 +0000 (14:42 -0800)]
net/mlx5e: Split between RX/TX tunnel FW support indication
Use the new FW caps to advertise for ip-in-ip tunnel support separately
for RX and TX.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
YueHaibing [Tue, 1 Dec 2020 22:42:06 +0000 (14:42 -0800)]
net/mlx5: Fix passing zero to 'PTR_ERR'
Fix smatch warnings:
drivers/net/ethernet/mellanox/mlx5/core/esw/acl/egress_lgcy.c:105 esw_acl_egress_lgcy_setup() warn: passing zero to 'PTR_ERR'
drivers/net/ethernet/mellanox/mlx5/core/esw/acl/egress_ofld.c:177 esw_acl_egress_ofld_setup() warn: passing zero to 'PTR_ERR'
drivers/net/ethernet/mellanox/mlx5/core/esw/acl/ingress_lgcy.c:184 esw_acl_ingress_lgcy_setup() warn: passing zero to 'PTR_ERR'
drivers/net/ethernet/mellanox/mlx5/core/esw/acl/ingress_ofld.c:262 esw_acl_ingress_ofld_setup() warn: passing zero to 'PTR_ERR'
esw_acl_table_create() never returns NULL, so
NULL test should be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Shay Drory [Tue, 1 Dec 2020 22:42:05 +0000 (14:42 -0800)]
net/mlx5: Arm only EQs with EQEs
Currently, when more than one EQ is sharing an IRQ, and this IRQ is
being interrupted, all the EQs sharing the IRQ will be armed. This is
done regardless of whether an EQ has EQE.
When multiple EQs are sharing an IRQ, one or more EQs can have valid
EQEs.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
YueHaibing [Tue, 1 Dec 2020 22:42:04 +0000 (14:42 -0800)]
net/mlx5e: Remove duplicated include
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Zhu Yanjun [Tue, 1 Dec 2020 22:42:03 +0000 (14:42 -0800)]
net/mlx5e: remove unnecessary memset
Since kvzalloc will initialize the allocated memory, it is not
necessary to initialize it once again.
Fixes:
11b717d61526 ("net/mlx5: E-Switch, Get reg_c0 value on CQE")
Signed-off-by: Zhu Yanjun <yanjunz@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Eran Ben Elisha [Tue, 1 Dec 2020 22:42:02 +0000 (14:42 -0800)]
net/mlx5e: Add TX port timestamp support
Transmitted packet timestamping accuracy can be improved when using
timestamp from the port, instead of packet CQE creation timestamp, as
it better reflects the actual time of a packet's transmit.
TX port timestamping is supported starting from ConnectX6-DX hardware.
Although at the original completion, only CQE timestamp can be attached,
we are able to get TX port timestamping via an additional completion over
a special CQ associated with the SQ (in addition to the regular CQ).
Driver to ignore the original packet completion timestamp, and report
back the timestamp of the special CQ completion. If the absolute timestamp
diff between the two completions is greater than 1 / 128 second, ignore
the TX port timestamp as it has a jitter which is too big.
No skb will be generate out of the extra completion.
Allocate additional CQ per ptpsq, to receive the TX port timestamp.
Driver to hold an skb FIFO in order to map between transmitted skb to
the two expected completions. When using ptpsq, hold double refcount on
the skb, to gaurantee it will not get released before both completions
arrive.
Expose dedicated counters of the ptp additional CQ and connect it to the
TX health reporter.
This patch improves TX Hardware timestamping offset to be less than 40ns
at a 100Gbps line rate, compared to 600ns before.
With that, making our HW compliant with G.8273.2 class C, and allow Linux
systems to be deployed in the 5G telco edge, where this standard is a
must.
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Eran Ben Elisha [Tue, 1 Dec 2020 22:42:01 +0000 (14:42 -0800)]
net/mlx5e: Add TX PTP port object support
Add TX PTP port object support for better TX timestamping accuracy.
Currently, driver supports CQE based TX port timestamp. Device
also offers TX port timestamp, which has less jitter and better
reflects the actual time of a packet's transmit.
Define new driver layout called ptpsq, on which driver will create
SQs that will support TX port timestamp for their transmitted packets.
Driver to identify PTP TX skbs and steer them to these dedicated SQs
as part of the select queue ndo.
Driver to hold ptpsq per TC and report them at
netif_set_real_num_tx_queues().
Add support for all needed functionality in order to xmit and poll
completions received via ptpsq.
Add ptpsq to the TX reporter recover, diagnose and dump methods.
Creation of ptpsqs is disabled by default, and can be enabled via
tx_port_ts private flag.
This patch steer all timestamp related packets to a ptpsq, but it
does not open the port timestamp support for it. The support will
be added in the following patch.
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Eran Ben Elisha [Tue, 1 Dec 2020 22:42:00 +0000 (14:42 -0800)]
net/mlx5e: Move MLX5E_RX_ERR_CQE macro
MLX5E_RX_ERR_CQE Macro is used only in data-path, move it to the
appropriate header file.
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Eran Ben Elisha [Tue, 1 Dec 2020 22:41:59 +0000 (14:41 -0800)]
net/mlx5e: Split SW group counters update function
SW group counter update function aggregates sw stats out of many
mlx5e_*_stats resides in a given mlx5e_channel_stats struct.
Split the function into a few helper functions.
This will be used later in the series to calculate specific
mlx5e_*_stats which are not defined inside mlx5e_channel_stats.
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Eran Ben Elisha [Tue, 1 Dec 2020 22:41:58 +0000 (14:41 -0800)]
net/mlx5e: Change skb fifo push/pop API to be used without SQ
The skb fifo push/pop API used pre-defined attributes within the
mlx5e_txqsq.
In order to share the skb fifo API with other non-SQ use cases,
change the API input to get newly defined mlx5e_skb_fifo struct.
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Eran Ben Elisha [Tue, 1 Dec 2020 22:41:57 +0000 (14:41 -0800)]
net/mlx5e: Allow SQ outside of channel context
In order to be able to create an SQ outside of a channel context, remove
sq->channel direct pointer. This requires adding a direct pointer to:
netdevice, priv and mlx5_core in order to support SQs that are part of
mlx5e_channel. Use channel_stats from the corresponding CQ.
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Aya Levin [Tue, 1 Dec 2020 22:41:56 +0000 (14:41 -0800)]
net/mlx5e: Allow RQ outside of channel context
In order to be able to create an RQ outside of a channel context, remove
rq->channel direct pointer. This requires adding a direct pointer to:
ICOSQ and priv in order to support RQs that are part of mlx5e_channel.
Use channel_stats from the corresponding CQ.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Aya Levin [Tue, 1 Dec 2020 22:41:55 +0000 (14:41 -0800)]
net/mlx5e: Allow CQ outside of channel context
In order to be able to create a CQ outside of a channel context, remove
cq->channel direct pointer. This requires adding a direct pointer to
channel statistics, netdevice, priv and to mlx5_core in order to support
CQs that are a part of mlx5e_channel.
In addition, parameters the were previously derived from the channel
like napi, NUMA node, channel stats and index are now assembled in
struct mlx5e_create_cq_param which is given to mlx5e_open_cq() instead
of channel pointer. Generalizing mlx5e_open_cq() allows opening CQ
outside of channel context which will be used in following patches in
the patch-set.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Tariq Toukan [Tue, 1 Dec 2020 22:41:54 +0000 (14:41 -0800)]
net/mlx5e: Free drop RQ in a dedicated function
The drop RQ has very limited objects to be freed, and differs
from regular RQs in the context that it is freed from.
Add a dedicated function for it, use it where needed, and remove
the drop_rq-specific checks in the generic function.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Rasmus Villemoes [Sat, 5 Dec 2020 13:39:44 +0000 (14:39 +0100)]
net: dsa: print the MTU value that could not be set
These warnings become somewhat more informative when they include the
MTU value that could not be set and not just the errno.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20201205133944.10182-1-rasmus.villemoes@prevas.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 8 Dec 2020 02:36:21 +0000 (18:36 -0800)]
Merge branch 'mlx5-next' of git://git./linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-next auxbus support
This pull request is targeting net-next and rdma-next branches.
This series provides mlx5 support for auxiliary bus devices.
It starts with a merge commit of tag 'auxbus-5.11-rc1' from
gregkh/driver-core into mlx5-next, then the mlx5 patches that will convert
mlx5 ulp devices (netdev, rdma, vdpa) to use the proper auxbus
infrastructure instead of the internal mlx5 device and interface management
implementation, which Leon is deleting at the end of this patchset.
Link: https://lore.kernel.org/alsa-devel/20201026111849.1035786-1-leon@kernel.org/
Thanks to everyone for the joint effort !
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
RDMA/mlx5: Remove IB representors dead code
net/mlx5: Simplify eswitch mode check
net/mlx5: Delete custom device management logic
RDMA/mlx5: Convert mlx5_ib to use auxiliary bus
net/mlx5e: Connect ethernet part to auxiliary bus
vdpa/mlx5: Connect mlx5_vdpa to auxiliary bus
net/mlx5: Register mlx5 devices to auxiliary virtual bus
vdpa/mlx5: Make hardware definitions visible to all mlx5 devices
net/mlx5_core: Clean driver version and name
net/mlx5: Properly convey driver version to firmware
driver core: auxiliary bus: minor coding style tweaks
driver core: auxiliary bus: make remove function return void
driver core: auxiliary bus: move slab.h from include file
Add auxiliary bus support
====================
Link: https://lore.kernel.org/r/20201207053349.402772-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tariq Toukan [Sun, 6 Dec 2020 09:12:54 +0000 (11:12 +0200)]
net/mlx4: Remove unused #define MAX_MSIX_P_PORT
All usages of the definition MAX_MSIX_P_PORT were removed.
It's not in use anymore. Remove it.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Link: https://lore.kernel.org/r/20201206091254.12476-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jarod Wilson [Sat, 5 Dec 2020 17:40:03 +0000 (12:40 -0500)]
bonding: set xfrm feature flags more sanely
We can remove one of the ifdef blocks here, and instead of setting both
the xfrm hw_features and features flags, then unsetting the feature
flags if not in AB, wait to set the features flags if we're actually in AB
mode.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Link: https://lore.kernel.org/r/20201205174003.578267-1-jarod@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sukadev Bhattiprolu [Sat, 5 Dec 2020 02:22:35 +0000 (18:22 -0800)]
ibmvnic: add some debugs
We sometimes run into situations where a soft/hard reset of the adapter
takes a long time or fails to complete. Having additional messages that
include important adapter state info will hopefully help understand what
is happening, reduce the guess work and minimize requests to reproduce
problems with debug patches.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Link: https://lore.kernel.org/r/20201205022235.2414110-1-sukadev@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David S. Miller [Mon, 7 Dec 2020 14:55:21 +0000 (06:55 -0800)]
Merge branch 's390-qeth-next'
Julian Wiedmann says:
====================
s390/qeth: updates 2020-12-07
please apply the following patch series for qeth to netdev's net-next tree.
Some sysfs cleanups (with the prep work in ccwgroup acked by Heiko), and
a few improvements to the code that deals with async TX completion
notifications for IQD devices.
This also brings the missing patch from the previous net-next submission.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Mon, 7 Dec 2020 13:12:33 +0000 (14:12 +0100)]
s390/qeth: make qeth_qdio_handle_aob() more robust
When qeth_qdio_handle_aob() frees dangling allocations in the notified
TX buffer, there are rare tear-down cases where
qeth_drain_output_queue() would later call qeth_clear_output_buffer()
for the same buffer - and thus end up walking the buffer a second time
to check for dangling kmem_cache allocations.
Luckily current code previously scrubs such a buffer, so
qeth_clear_output_buffer() would find buf->buffer->element[i].addr as
NULL and not do anything. But this is fragile, and we can easily improve
it by consistently clearing the ->is_header flag after freeing the
allocation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Mon, 7 Dec 2020 13:12:32 +0000 (14:12 +0100)]
s390/qeth: remove QETH_QDIO_BUF_HANDLED_DELAYED state
Reuse the QETH_QDIO_BUF_EMPTY state to indicate that a TX buffer has
been completed with a QAOB notification, and may be cleaned up by
qeth_cleanup_handled_pending().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Mon, 7 Dec 2020 13:12:31 +0000 (14:12 +0100)]
s390/qeth: don't replace a fully completed async TX buffer
For TX buffers that require an additional async notification via QAOB, the
TX completion code can now manage all the necessary processing if the
notification has already occurred (or is occurring concurrently).
In such cases we can avoid replacing the metadata that is associated
with the buffer's slot on the ring, and just keep using the current one.
As qeth_clear_output_buffer() will also handle any kmem cache-allocated
memory that was mapped into the TX buffer, qeth_qdio_handle_aob()
doesn't need to worry about it.
While at it, also remove the unneeded forward declaration for
qeth_init_qdio_out_buf().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Mon, 7 Dec 2020 13:12:30 +0000 (14:12 +0100)]
s390/qeth: use dev->groups for common sysfs attributes
All qeth devices have a minimum set of sysfs attributes, and non-OSN
devices share a group of additional attributes. Depending on whether
the device is forced to use a specific discipline, the device_type then
specifies further attributes.
Shift the common attributes into dev->groups, so that the device_type
only contains the discipline-specific attributes. This avoids exposing
the common attributes to the disciplines, and nicely cleans up our
sysfs code.
While replacing the qeth_l*_*_device_attributes() helpers, switch from
sysfs_*_groups() to the more generic device_*_groups().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Mon, 7 Dec 2020 13:12:29 +0000 (14:12 +0100)]
s390/ccwgroup: use bus->dev_groups for bus-based sysfs attributes
Bus drivers have their own way of describing the sysfs attributes that
all devices on a bus should provide.
Switch ccwgroup_attr_groups over to use bus->dev_groups, and thus
free up dev->groups for usage by the ccwgroup device drivers.
While adjusting the attribute naming, use ATTRIBUTE_GROUPS() to get rid
of some boilerplate code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Mon, 7 Dec 2020 13:12:28 +0000 (14:12 +0100)]
s390/qeth: don't call INIT_LIST_HEAD() on iob's list entry
INIT_LIST_HEAD() only needs to be called on actual list heads.
While at it clarify the naming of the field.
Suggested-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 7 Dec 2020 03:22:15 +0000 (19:22 -0800)]
Merge branch 'mlxsw-Misc-updates'
Ido Schimmel says:
====================
mlxsw: Misc updates
This patchset contains miscellaneous patches we gathered in our queue.
Some of them are dependencies of larger patchsets that I will submit
later this cycle.
Patches #1-#3 perform small non-functional changes in mlxsw.
Patch #4 adds more extended ack messages in mlxsw.
Patch #5 adds devlink parameters documentation for mlxsw. To be extended
with more parameters this cycle.
Patches #6-#7 perform small changes in forwarding selftests
infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Sun, 6 Dec 2020 08:22:27 +0000 (10:22 +0200)]
mlxsw: spectrum_router: Reduce mlxsw_sp_ipip_fib_entry_op_gre4()
Turned out that mlxsw_sp_ipip_fib_entry_op_gre4() does not need to
figure out the IP address and virtual router id. Those are exactly
the same as in the fib_entry it is called for. So just use that and
reduce mlxsw_sp_ipip_fib_entry_op_gre4() function to only call
mlxsw_sp_ipip_fib_entry_op_gre4_rtdp() make the ipip decap op
code similar to nve.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 6 Dec 2020 08:22:26 +0000 (10:22 +0200)]
mlxsw: spectrum: Bump minimum FW version to xx.2008.2018
The indicated version fixes an issue whereby the MOMTE register would by
default enable mirroring of ECN-marked traffic from all traffic classes,
once the ECN mirroring was configured. This fix is necessary for offload
of RED "ecn_mark" qevent.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 6 Dec 2020 08:22:25 +0000 (10:22 +0200)]
mlxsw: core_acl: Use an array instead of a struct with a zero-length array
Suppresses the following coccinelle warning:
drivers/net/ethernet/mellanox/mlxsw/core_acl_flex_keys.c:139:3-7:
WARNING use flexible-array member instead
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 6 Dec 2020 08:22:24 +0000 (10:22 +0200)]
mlxsw: spectrum_mr: Use flexible-array member instead of zero-length array
Suppresses the following coccinelle warning:
drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:18:15-19: WARNING use flexible-array member instead
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 6 Dec 2020 08:22:23 +0000 (10:22 +0200)]
mlxsw: core: Trace EMAD events
Currently, mlxsw triggers the 'devlink:devlink_hwmsg' tracepoint
whenever a request is sent to the device and whenever a response is
received from it. However, the tracepoint is not triggered when an event
(e.g., port up / down) is received from the device.
Also trace EMAD events in order to log a more complete picture of all
the exchanged hardware messages.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 6 Dec 2020 08:22:22 +0000 (10:22 +0200)]
selftests: mlxsw: Test RIF's reference count when joining a LAG
Test that the reference count of a router interface (RIF) configured for
a LAG is incremented / decremented when ports join / leave the LAG. Use
the offload indication on routes configured on the RIF to understand if
it was created / destroyed.
The test fails without the previous patch.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 6 Dec 2020 08:22:21 +0000 (10:22 +0200)]
mlxsw: spectrum: Apply RIF configuration when joining a LAG
In case a router interface (RIF) is configured for a LAG, make sure its
configuration is applied on the new LAG member.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky [Sat, 10 Oct 2020 09:27:27 +0000 (12:27 +0300)]
RDMA/mlx5: Remove IB representors dead code
Delete dead code.
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Leon Romanovsky [Sat, 10 Oct 2020 08:57:26 +0000 (11:57 +0300)]
net/mlx5: Simplify eswitch mode check
Provide mlx5_core device instead of "priv" pointer while checking
eswith mode.
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Leon Romanovsky [Mon, 5 Oct 2020 08:13:56 +0000 (11:13 +0300)]
net/mlx5: Delete custom device management logic
After conversion to use auxiliary bus, all custom device management is
not needed anymore, delete it.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Leon Romanovsky [Sun, 4 Oct 2020 04:35:36 +0000 (07:35 +0300)]
RDMA/mlx5: Convert mlx5_ib to use auxiliary bus
The conversion to auxiliary bus solves long standing issue with
existing mlx5_ib<->mlx5_core coupling. It required to have both
modules in initramfs if one of them needed for the boot.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Leon Romanovsky [Mon, 5 Oct 2020 05:08:25 +0000 (08:08 +0300)]
net/mlx5e: Connect ethernet part to auxiliary bus
Reuse auxiliary bus to perform device management of the
ethernet part of the mlx5 driver.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Leon Romanovsky [Sun, 4 Oct 2020 12:38:20 +0000 (15:38 +0300)]
vdpa/mlx5: Connect mlx5_vdpa to auxiliary bus
Change module registration logic to use auxiliary bus instead of custom
made mlx5 register interface.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
David S. Miller [Sun, 6 Dec 2020 00:29:21 +0000 (16:29 -0800)]
Merge branch 'r8169-improve-rtl_rx-and-NUM_RX_DESC-handling'
Heiner Kallweit says:
====================
r8169: improve rtl_rx and NUM_RX_DESC handling
This series improves rtl_rx() and the handling of NUM_RX_DESC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sun, 6 Dec 2020 00:00:54 +0000 (01:00 +0100)]
r8169: make NUM_RX_DESC a signed int
After recent changes there's no need any longer to define NUM_RX_DESC
as an unsigned value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sun, 6 Dec 2020 00:00:07 +0000 (01:00 +0100)]
r8169: improve rtl_rx
There's no need to check min(budget, NUM_RX_DESC). At first budget
(NAPI_POLL_WEIGHT = 64) is less then NUM_RX_DESC (256).
And more important: Even in case of budget > NUM_RX_DESC we could
safely continue processing descriptors as long as they are owned by
the CPU. In addition replace rx_left with a normal counter variable,
this allows to simplify the code. Last but not least there's no need
any longer to pass the budget as an u32.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 4 Dec 2020 19:45:49 +0000 (19:45 +0000)]
net: fix spelling mistake "wil" -> "will" in Kconfig
There is a spelling mistake in the Kconfig help text. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201204194549.1153063-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 5 Dec 2020 23:08:05 +0000 (15:08 -0800)]
Merge tag 'batadv-next-pullrequest-
20201204' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- update include for min/max helpers, by Sven Eckelmann
- add infrastructure and netlink functions for routing algo selection,
by Sven Eckelmann (2 patches)
- drop deprecated debugfs and sysfs support and obsoleted
functionality, by Sven Eckelmann (3 patches)
- drop unused include in fragmentation.c, by Simon Wunderlich
* tag 'batadv-next-pullrequest-
20201204' of git://git.open-mesh.org/linux-merge:
batman-adv: Drop unused soft-interface.h include in fragmentation.c
batman-adv: Drop legacy code for auto deleting mesh interfaces
batman-adv: Drop deprecated debugfs support
batman-adv: Drop deprecated sysfs support
batman-adv: Allow selection of routing algorithm over rtnetlink
batman-adv: Prepare infrastructure for newlink settings
batman-adv: Add new include for min/max helpers
batman-adv: Start new development cycle
====================
Link: https://lore.kernel.org/r/20201204154631.21063-1-sw@simonwunderlich.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arnd Bergmann [Fri, 4 Dec 2020 12:08:00 +0000 (14:08 +0200)]
enetc: Fix unused var build warning for CONFIG_OF
When CONFIG_OF is disabled, there is a harmless warning about
an unused variable:
enetc_pf.c: In function 'enetc_phylink_create':
enetc_pf.c:981:17: error: unused variable 'dev' [-Werror=unused-variable]
Slightly rearrange the code to pass around the of_node as a
function argument, which avoids the problem without hurting
readability.
Fixes:
71b77a7a27a3 ("enetc: Migrate to PHYLINK and PCS_LYNX")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201204120800.17193-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonathan Lemon [Fri, 4 Dec 2020 03:51:28 +0000 (19:51 -0800)]
ptp: Add clock driver for the OpenCompute TimeCard.
The OpenCompute time card is an atomic clock along with
a GPS receiver that provides a Grandmaster clock source
for a PTP enabled network.
More information is available at http://www.timingcard.com/
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20201204035128.2219252-2-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bongsu Jeon [Wed, 2 Dec 2020 22:31:47 +0000 (07:31 +0900)]
net/nfc/nci: Support NCI 2.x initial sequence
implement the NCI 2.x initial sequence to support NCI 2.x NFCC.
Since NCI 2.0, CORE_RESET and CORE_INIT sequence have been changed.
If NFCEE supports NCI 2.x, then NCI 2.x initial sequence will work.
In NCI 1.0, Initial sequence and payloads are as below:
(DH) (NFCC)
| -- CORE_RESET_CMD --> |
| <-- CORE_RESET_RSP -- |
| -- CORE_INIT_CMD --> |
| <-- CORE_INIT_RSP -- |
CORE_RESET_RSP payloads are Status, NCI version, Configuration Status.
CORE_INIT_CMD payloads are empty.
CORE_INIT_RSP payloads are Status, NFCC Features,
Number of Supported RF Interfaces, Supported RF Interface,
Max Logical Connections, Max Routing table Size,
Max Control Packet Payload Size, Max Size for Large Parameters,
Manufacturer ID, Manufacturer Specific Information.
In NCI 2.0, Initial Sequence and Parameters are as below:
(DH) (NFCC)
| -- CORE_RESET_CMD --> |
| <-- CORE_RESET_RSP -- |
| <-- CORE_RESET_NTF -- |
| -- CORE_INIT_CMD --> |
| <-- CORE_INIT_RSP -- |
CORE_RESET_RSP payloads are Status.
CORE_RESET_NTF payloads are Reset Trigger,
Configuration Status, NCI Version, Manufacturer ID,
Manufacturer Specific Information Length,
Manufacturer Specific Information.
CORE_INIT_CMD payloads are Feature1, Feature2.
CORE_INIT_RSP payloads are Status, NFCC Features,
Max Logical Connections, Max Routing Table Size,
Max Control Packet Payload Size,
Max Data Packet Payload Size of the Static HCI Connection,
Number of Credits of the Static HCI Connection,
Max NFC-V RF Frame Size, Number of Supported RF Interfaces,
Supported RF Interfaces.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Link: https://lore.kernel.org/r/20201202223147.3472-1-bongsu.jeon@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guillaume Nault [Wed, 2 Dec 2020 14:35:43 +0000 (15:35 +0100)]
selftests: forwarding: Add MPLS L2VPN test
Connect hosts H1 and H2 using two intermediate encapsulation routers
(LER1 and LER2). These routers encapsulate traffic from the hosts,
including the original Ethernet header, into MPLS.
Use ping to test reachability between H1 and H2.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://lore.kernel.org/r/625f5c1aafa3a8085f8d3e082d680a82e16ffbaa.1606918980.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tom Rix [Wed, 2 Dec 2020 16:36:22 +0000 (08:36 -0800)]
net: bna: remove trailing semicolon in macro definition
The macro use will already have a semicolon.
Clean up escaped newlines.
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20201202163622.3733506-1-trix@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hoang Le [Thu, 3 Dec 2020 03:50:45 +0000 (10:50 +0700)]
tipc: support 128bit node identity for peer removing
We add the support to remove a specific node down with 128bit
node identifier, as an alternative to legacy 32-bit node address.
example:
$tipc peer remove identiy <
1001002|
16777777>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Link: https://lore.kernel.org/r/20201203035045.4564-1-hoang.h.le@dektech.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simon Horman [Fri, 4 Dec 2020 12:56:01 +0000 (13:56 +0100)]
nfp: Replace zero-length array with flexible-array member
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code
should always use "flexible array members"[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9/process/deprecated.html#zero-length-and-one-element-arrays
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Link: https://lore.kernel.org/r/20201204125601.24876-1-simon.horman@netronome.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bongsu Jeon [Thu, 3 Dec 2020 22:52:57 +0000 (07:52 +0900)]
nfc: s3fwrn5: skip the NFC bootloader mode
If there isn't a proper NFC firmware image, Bootloader mode will be
skipped.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201203225257.2446-1-bongsu.jeon@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 4 Dec 2020 21:40:55 +0000 (13:40 -0800)]
Merge branch 'perf-optimizations-for-tcp-recv-zerocopy'
Arjun Roy says:
====================
Perf. optimizations for TCP Recv. Zerocopy
This patchset contains several optimizations for TCP Recv. Zerocopy.
Summarized:
1. It is possible that a read payload is not exactly page aligned -
that there may exist "straggler" bytes that we cannot map into the
caller's address space cleanly. For this, we allow the caller to
provide as argument a "hybrid copy buffer", turning
getsockopt(TCP_ZEROCOPY_RECEIVE) into a "hybrid" operation that allows
the caller to avoid a subsequent recvmsg() call to read the
stragglers.
2. Similarly, for "small" read payloads that are either below the size
of a page, or small enough that remapping pages is not a performance
win - we allow the user to short-circuit the remapping operations
entirely and simply copy into the buffer provided.
Some of the patches in the middle of this set are refactors to support
this "short-circuiting" optimization.
3. We allow the user to provide a hint that performing a page zap
operation (and the accompanying TLB shootdown) may not be necessary,
for the provided region that the kernel will attempt to map pages
into. This allows us to avoid this expensive operation while holding
the socket lock, which provides a significant performance advantage.
With all of these changes combined, "medium" sized receive traffic
(multiple tens to few hundreds of KB) see significant efficiency gains
when using TCP receive zerocopy instead of regular recvmsg(). For
example, with RPC-style traffic with 32KB messages, there is a roughly
15% efficiency improvement when using zerocopy. Without these changes,
there is a roughly 60-70% efficiency reduction with such messages when
employing zerocopy.
====================
Link: https://lore.kernel.org/r/20201202225349.935284-1-arjunroy.kdev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arjun Roy [Wed, 2 Dec 2020 22:53:49 +0000 (14:53 -0800)]
net-zerocopy: Defer vm zap unless actually needed.
Zapping pages is required only if we are calling vm_insert_page into a
region where pages had previously been mapped. Receive zerocopy allows
reusing such regions, and hitherto called zap_page_range() before
calling vm_insert_page() in that range.
zap_page_range() can also be triggered from userspace with
madvise(MADV_DONTNEED). If userspace is configured to call this before
reusing a segment, or if there was nothing mapped at this virtual
address to begin with, we can avoid calling zap_page_range() under the
socket lock. That said, if userspace does not do that, then we are
still responsible for calling zap_page_range().
This patch adds a flag that the user can use to hint to the kernel
that a zap is not required. If the flag is not set, or if an older
user application does not have a flags field at all, then the kernel
calls zap_page_range as before. Also, if the flag is set but a zap is
still required, the kernel performs that zap as necessary. Thus
incorrectly indicating that a zap can be avoided does not change the
correctness of operation. It also increases the batchsize for
vm_insert_pages and prefetches the page struct for the batch since
we're about to bump the refcount.
An alternative mechanism could be to not have a flag, assume by
default a zap is not needed, and fall back to zapping if needed.
However, this would harm performance for older applications for which
a zap is necessary, and thus we implement it with an explicit flag
so newer applications can opt in.
When using RPC-style traffic with medium sized (tens of KB) RPCs, this
change yields an efficency improvement of about 30% for QPS/CPU usage.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arjun Roy [Wed, 2 Dec 2020 22:53:48 +0000 (14:53 -0800)]
net-zerocopy: Set zerocopy hint when data is copied
Set zerocopy hint, event when falling back to copy, so that the
pending data can be efficiently received using zerocopy when
possible.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arjun Roy [Wed, 2 Dec 2020 22:53:47 +0000 (14:53 -0800)]
net-zerocopy: Introduce short-circuit small reads.
Sometimes, we may call tcp receive zerocopy when inq is 0,
or inq < PAGE_SIZE, or inq is generally small enough that
it is cheaper to copy rather than remap pages.
In these cases, we may want to either return early (inq=0) or
attempt to use the provided copy buffer to simply copy
the received data.
This allows us to save both system call overhead and
the latency of acquiring mmap_sem in read mode for cases where
it would be useless to do so.
This patchset enables this behaviour by:
1. Returning quickly if inq is 0.
2. Attempting to perform a regular copy if a hybrid copybuffer is
provided and it is large enough to absorb all available bytes.
3. Return quickly if no such buffer was provided and there are less
than PAGE_SIZE bytes available.
For small RPC ping-pong workloads, normally we would have
1 getsockopt(), 1 recvmsg() and 1 sendmsg() call per RPC. With this
change, we remove the recvmsg() call entirely, reducing the syscall
overhead by about 33%. In testing with small (hundreds of bytes)
RPC traffic, this yields a syscall reduction of about 33% and
an efficiency gain of about 3-5% when defined as QPS/CPU Util.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arjun Roy [Wed, 2 Dec 2020 22:53:46 +0000 (14:53 -0800)]
net-zerocopy: Fast return if inq < PAGE_SIZE
Sometimes, we may call tcp receive zerocopy when inq is 0,
or inq < PAGE_SIZE, in which case we cannot remap pages. In this case,
simply return the appropriate hint for regular copying without taking
mmap_sem.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arjun Roy [Wed, 2 Dec 2020 22:53:45 +0000 (14:53 -0800)]
net-zerocopy: Refactor frag-is-remappable test.
Refactor frag-is-remappable test for tcp receive zerocopy. This is
part of a patch set that introduces short-circuited hybrid copies
for small receive operations, which results in roughly 33% fewer
syscalls for small RPC scenarios.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arjun Roy [Wed, 2 Dec 2020 22:53:44 +0000 (14:53 -0800)]
net-zerocopy: Refactor skb frag fast-forward op.
Refactor skb frag fast-forwarding for tcp receive zerocopy. This is
part of a patch set that introduces short-circuited hybrid copies
for small receive operations, which results in roughly 33% fewer
syscalls for small RPC scenarios.
skb_advance_to_frag(), given a skb and an offset into the skb,
iterates from the first frag for the skb until we're at the frag
specified by the offset. Assuming the offset provided refers to how
many bytes in the skb are already read, the returned frag points to
the next frag we may read from, while offset_frag is set to the number
of bytes from this frag that we have already read.
If frag is not null and offset_frag is equal to 0, then we may be able
to map this frag's page into the process address space with
vm_insert_page(). However, if offset_frag is not equal to 0, then we
cannot do so.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arjun Roy [Wed, 2 Dec 2020 22:53:43 +0000 (14:53 -0800)]
net-tcp: Introduce tcp_recvmsg_locked().
Refactor tcp_recvmsg() by splitting it into locked and unlocked
portions. Callers already holding the socket lock and not using
ERRQUEUE/cmsg/busy polling can simply call tcp_recvmsg_locked().
This is in preparation for a short-circuit copy performed by
TCP receive zerocopy for small (< PAGE_SIZE, or otherwise requested
by the user) reads.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arjun Roy [Wed, 2 Dec 2020 22:53:42 +0000 (14:53 -0800)]
net-zerocopy: Copy straggler unaligned data for TCP Rx. zerocopy.
When TCP receive zerocopy does not successfully map the entire
requested space, it outputs a 'hint' that the caller should recvmsg().
Augment zerocopy to accept a user buffer that it tries to copy this
hint into - if it is possible to copy the entire hint, it will do so.
This elides a recvmsg() call for received traffic that isn't exactly
page-aligned in size.
This was tested with RPC-style traffic of arbitrary sizes. Normally,
each received message required at least one getsockopt() call, and one
recvmsg() call for the remaining unaligned data.
With this change, almost all of the recvmsg() calls are eliminated,
leading to a savings of about 25%-50% in number of system calls
for RPC-style workloads.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 4 Dec 2020 21:30:53 +0000 (13:30 -0800)]
Merge branch 'seg6-add-support-for-srv6-end-dt4-dt6-behavior'
Andrea Mayer says:
====================
seg6: add support for SRv6 End.DT4/DT6 behavior
This patchset provides support for the SRv6 End.DT4 and End.DT6 (VRF mode)
behaviors.
The SRv6 End.DT4 behavior is used to implement multi-tenant IPv4 L3 VPNs. It
decapsulates the received packets and performs IPv4 routing lookup in the
routing table of the tenant. The SRv6 End.DT4 Linux implementation leverages a
VRF device in order to force the routing lookup into the associated routing
table.
The SRv6 End.DT4 behavior is defined in the SRv6 Network Programming [1].
The Linux kernel already offers an implementation of the SRv6 End.DT6 behavior
which allows us to set up IPv6 L3 VPNs over SRv6 networks. This new
implementation of DT6 is based on the same VRF infrastructure already exploited
for implementing the SRv6 End.DT4 behavior. The aim of the new SRv6 End.DT6 in
VRF mode consists in simplifying the construction of IPv6 L3 VPN services in
the multi-tenant environment.
Currently, the two SRv6 End.DT6 implementations (legacy and VRF mode)
coexist seamlessly and can be chosen according to the context and the user
preferences.
- Patch 1 is needed to solve a pre-existing issue with tunneled packets
when a sniffer is attached;
- Patch 2 improves the management of the seg6local attributes used by the
SRv6 behaviors;
- Patch 3 adds support for optional attributes in SRv6 behaviors;
- Patch 4 introduces two callbacks used for customizing the
creation/destruction of a SRv6 behavior;
- Patch 5 is the core patch that adds support for the SRv6 End.DT4
behavior;
- Patch 6 introduces the VRF support for SRv6 End.DT6 behavior;
- Patch 7 adds the selftest for SRv6 End.DT4 behavior;
- Patch 8 adds the selftest for SRv6 End.DT6 (VRF mode) behavior.
Regarding iproute2, the support for the new "vrftable" attribute, required by
both SRv6 End.DT4 and End.DT6 (VRF mode) behaviors, is provided in a different
patchset that will follow shortly.
I would like to thank David Ahern for his support during the development of
this patchset.
[1] https://tools.ietf.org/html/draft-ietf-spring-srv6-network-programming
====================
Link: https://lore.kernel.org/r/20201202130517.4967-1-andrea.mayer@uniroma2.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrea Mayer [Wed, 2 Dec 2020 13:05:17 +0000 (14:05 +0100)]
selftests: add selftest for the SRv6 End.DT6 (VRF) behavior
this selftest is designed for evaluating the new SRv6 End.DT6 (VRF) behavior
used, in this example, for implementing IPv6 L3 VPN use cases.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Paolo Lungaroni <paolo.lungaroni@cnit.it>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrea Mayer [Wed, 2 Dec 2020 13:05:16 +0000 (14:05 +0100)]
selftests: add selftest for the SRv6 End.DT4 behavior
this selftest is designed for evaluating the new SRv6 End.DT4 behavior
used, in this example, for implementing IPv4 L3 VPN use cases.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrea Mayer [Wed, 2 Dec 2020 13:05:15 +0000 (14:05 +0100)]
seg6: add VRF support for SRv6 End.DT6 behavior
SRv6 End.DT6 is defined in the SRv6 Network Programming [1].
The Linux kernel already offers an implementation of the SRv6
End.DT6 behavior which permits IPv6 L3 VPNs over SRv6 networks. This
implementation is not particularly suitable in contexts where we need to
deploy IPv6 L3 VPNs among different tenants which share the same network
address schemes. The underlying problem lies in the fact that the
current version of DT6 (called legacy DT6 from now on) needs a complex
configuration to be applied on routers which requires ad-hoc routes and
routing policy rules to ensure the correct isolation of tenants.
Consequently, a new implementation of DT6 has been introduced with the
aim of simplifying the construction of IPv6 L3 VPN services in the
multi-tenant environment using SRv6 networks. To accomplish this task,
we reused the same VRF infrastructure and SRv6 core components already
exploited for implementing the SRv6 End.DT4 behavior.
Currently the two End.DT6 implementations coexist seamlessly and can be
used depending on the context and the user preferences. So, in order to
support both versions of DT6 a new attribute (vrftable) has been
introduced which allows us to differentiate the implementation of the
behavior to be used.
A SRv6 End.DT6 legacy behavior is still instantiated using a command
like the following one:
$ ip -6 route add 2001:db8::1 encap seg6local action End.DT6 table 100 dev eth0
While to instantiate the SRv6 End.DT6 in VRF mode, the command is still
pretty straight forward:
$ ip -6 route add 2001:db8::1 encap seg6local action End.DT6 vrftable 100 dev eth0.
Obviously as in the case of SRv6 End.DT4, the VRF strict_mode parameter
must be set (net.vrf.strict_mode=1) and the VRF associated with table
100 must exist.
Please note that the instances of SRv6 End.DT6 legacy and End.DT6 VRF
mode can coexist in the same system/configuration without problems.
[1] https://tools.ietf.org/html/draft-ietf-spring-srv6-network-programming
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrea Mayer [Wed, 2 Dec 2020 13:05:14 +0000 (14:05 +0100)]
seg6: add support for the SRv6 End.DT4 behavior
SRv6 End.DT4 is defined in the SRv6 Network Programming [1].
The SRv6 End.DT4 is used to implement IPv4 L3VPN use-cases in
multi-tenants environments. It decapsulates the received packets and it
performs IPv4 routing lookup in the routing table of the tenant.
The SRv6 End.DT4 Linux implementation leverages a VRF device in order to
force the routing lookup into the associated routing table.
To make the End.DT4 work properly, it must be guaranteed that the routing
table used for routing lookup operations is bound to one and only one
VRF during the tunnel creation. Such constraint has to be enforced by
enabling the VRF strict_mode sysctl parameter, i.e:
$ sysctl -wq net.vrf.strict_mode=1.
At JANOG44, LINE corporation presented their multi-tenant DC architecture
using SRv6 [2]. In the slides, they reported that the Linux kernel is
missing the support of SRv6 End.DT4 behavior.
The SRv6 End.DT4 behavior can be instantiated using a command similar to
the following:
$ ip route add 2001:db8::1 encap seg6local action End.DT4 vrftable 100 dev eth0
We introduce the "vrftable" extension in iproute2 in a following patch.
[1] https://tools.ietf.org/html/draft-ietf-spring-srv6-network-programming
[2] https://speakerdeck.com/line_developers/line-data-center-networking-with-srv6
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrea Mayer [Wed, 2 Dec 2020 13:05:13 +0000 (14:05 +0100)]
seg6: add callbacks for customizing the creation/destruction of a behavior
We introduce two callbacks used for customizing the creation/destruction of
a SRv6 behavior. Such callbacks are defined in the new struct
seg6_local_lwtunnel_ops and hereafter we provide a brief description of
them:
- build_state(...): used for calling the custom constructor of the
behavior during its initialization phase and after all the attributes
have been parsed successfully;
- destroy_state(...): used for calling the custom destructor of the
behavior before it is completely destroyed.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrea Mayer [Wed, 2 Dec 2020 13:05:12 +0000 (14:05 +0100)]
seg6: add support for optional attributes in SRv6 behaviors
Before this patch, each SRv6 behavior specifies a set of required
attributes that must be provided by the userspace application when such
behavior is going to be instantiated. If at least one of the required
attributes is not provided, the creation of the behavior fails.
The SRv6 behavior framework lacks a way to manage optional attributes.
By definition, an optional attribute for a SRv6 behavior consists of an
attribute which may or may not be provided by the userspace. Therefore,
if an optional attribute is missing (and thus not supplied by the user)
the creation of the behavior goes ahead without any issue.
This patch explicitly differentiates the required attributes from the
optional attributes. In particular, each behavior can declare a set of
required attributes and a set of optional ones.
The semantic of the required attributes remains *totally* unaffected by
this patch. The introduction of the optional attributes does NOT impact
on the backward compatibility of the existing SRv6 behaviors.
It is essential to note that if an (optional or required) attribute is
supplied to a SRv6 behavior which does not expect it, the behavior
simply discards such attribute without generating any error or warning.
This operating mode remained unchanged both before and after the
introduction of the optional attributes extension.
The optional attributes are one of the key components used to implement
the SRv6 End.DT6 behavior based on the Virtual Routing and Forwarding
(VRF) framework. The optional attributes make possible the coexistence
of the already existing SRv6 End.DT6 implementation with the new SRv6
End.DT6 VRF-based implementation without breaking any backward
compatibility. Further details on the SRv6 End.DT6 behavior (VRF mode)
are reported in subsequent patches.
From the userspace point of view, the support for optional attributes DO
NOT require any changes to the userspace applications, i.e: iproute2
unless new attributes (required or optional) are needed.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrea Mayer [Wed, 2 Dec 2020 13:05:11 +0000 (14:05 +0100)]
seg6: improve management of behavior attributes
Depending on the attribute (i.e.: SEG6_LOCAL_SRH, SEG6_LOCAL_TABLE, etc),
the parse() callback performs some validity checks on the provided input
and updates the tunnel state (slwt) with the result of the parsing
operation. However, an attribute may also need to reserve some additional
resources (i.e.: memory or setting up an eBPF program) in the parse()
callback to complete the parsing operation.
The parse() callbacks are invoked by the parse_nla_action() for each
attribute belonging to a specific behavior. Given a behavior with N
attributes, if the parsing of the i-th attribute fails, the
parse_nla_action() returns immediately with an error. Nonetheless, the
resources acquired during the parsing of the i-1 attributes are not freed
by the parse_nla_action().
Attributes which acquire resources must release them *in an explicit way*
in both the seg6_local_{build/destroy}_state(). However, adding a new
attribute of this type requires changes to
seg6_local_{build/destroy}_state() to release the resources correctly.
The seg6local infrastructure still lacks a simple and structured way to
release the resources acquired in the parse() operations.
We introduced a new callback in the struct seg6_action_param named
destroy(). This callback releases any resource which may have been acquired
in the parse() counterpart. Each attribute may or may not implement the
destroy() callback depending on whether it needs to free some acquired
resources.
The destroy() callback comes with several of advantages:
1) we can have many attributes as we want for a given behavior with no
need to explicitly free the taken resources;
2) As in case of the seg6_local_build_state(), the
seg6_local_destroy_state() does not need to handle the release of
resources directly. Indeed, it calls the destroy_attrs() function which
is in charge of calling the destroy() callback for every set attribute.
We do not need to patch seg6_local_{build/destroy}_state() anymore as
we add new attributes;
3) the code is more readable and better structured. Indeed, all the
information needed to handle a given attribute are contained in only
one place;
4) it facilitates the integration with new features introduced in further
patches.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrea Mayer [Wed, 2 Dec 2020 13:05:10 +0000 (14:05 +0100)]
vrf: add mac header for tunneled packets when sniffer is attached
Before this patch, a sniffer attached to a VRF used as the receiving
interface of L3 tunneled packets detects them as malformed packets and
it complains about that (i.e.: tcpdump shows bogus packets).
The reason is that a tunneled L3 packet does not carry any L2
information and when the VRF is set as the receiving interface of a
decapsulated L3 packet, no mac header is currently set or valid.
Therefore, the purpose of this patch consists of adding a MAC header to
any packet which is directly received on the VRF interface ONLY IF:
i) a sniffer is attached on the VRF and ii) the mac header is not set.
In this case, the mac address of the VRF is copied in both the
destination and the source address of the ethernet header. The protocol
type is set either to IPv4 or IPv6, depending on which L3 packet is
received.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 4 Dec 2020 18:56:37 +0000 (10:56 -0800)]
Merge tag 'wireless-drivers-next-2020-12-03' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.11
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
* tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (180 commits)
wl1251: remove trailing semicolon in macro definition
airo: remove trailing semicolon in macro definition
wilc1000: added queue support for WMM
wilc1000: call complete() for failure in wilc_wlan_txq_add_cfg_pkt()
wilc1000: free resource in wilc_wlan_txq_add_mgmt_pkt() for failure path
wilc1000: free resource in wilc_wlan_txq_add_net_pkt() for failure path
wilc1000: added 'ndo_set_mac_address' callback support
brcmfmac: expose firmware config files through modinfo
wlcore: Switch to using the new API kobj_to_dev()
rtw88: coex: add feature to enhance HID coexistence performance
rtw88: coex: upgrade coexistence A2DP mechanism
rtw88: coex: add action for coexistence in hardware initial
rtw88: coex: add function to avoid cck lock
rtw88: coex: change the coexistence mechanism for WLAN connected
rtw88: coex: change the coexistence mechanism for HID
rtw88: coex: update AFH information while in free-run mode
rtw88: coex: update the mechanism for A2DP + PAN
rtw88: coex: add debug message
rtw88: coex: run coexistence when WLAN entering/leaving LPS
Revert "rtl8xxxu: Add Buffalo WI-U3-866D to list of supported devices"
...
====================
Link: https://lore.kernel.org/r/20201203185732.9CFA5C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Anders Roxell [Thu, 3 Dec 2020 14:43:43 +0000 (15:43 +0100)]
dpaa_eth: fix build errorr in dpaa_fq_init
When building FSL_DPAA_ETH the following build error shows up:
/tmp/drivers/net/ethernet/freescale/dpaa/dpaa_eth.c: In function ‘dpaa_fq_init’:
/tmp/drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:1135:9: error: too few arguments to function ‘xdp_rxq_info_reg’
1135 | err = xdp_rxq_info_reg(&dpaa_fq->xdp_rxq, dpaa_fq->net_dev,
| ^~~~~~~~~~~~~~~~
Commit
b02e5a0ebb17 ("xsk: Propagate napi_id to XDP socket Rx path")
added an extra argument to function xdp_rxq_info_reg and commit
d57e57d0cd04 ("dpaa_eth: add XDP_TX support") didn't know about that
extra argument.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/r/20201203144343.790719-1-anders.roxell@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 4 Dec 2020 15:48:11 +0000 (07:48 -0800)]
Merge https://git./linux/kernel/git/bpf/bpf-next
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-12-03
The main changes are:
1) Support BTF in kernel modules, from Andrii.
2) Introduce preferred busy-polling, from Björn.
3) bpf_ima_inode_hash() and bpf_bprm_opts_set() helpers, from KP Singh.
4) Memcg-based memory accounting for bpf objects, from Roman.
5) Allow bpf_{s,g}etsockopt from cgroup bind{4,6} hooks, from Stanislav.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (118 commits)
selftests/bpf: Fix invalid use of strncat in test_sockmap
libbpf: Use memcpy instead of strncpy to please GCC
selftests/bpf: Add fentry/fexit/fmod_ret selftest for kernel module
selftests/bpf: Add tp_btf CO-RE reloc test for modules
libbpf: Support attachment of BPF tracing programs to kernel modules
libbpf: Factor out low-level BPF program loading helper
bpf: Allow to specify kernel module BTFs when attaching BPF programs
bpf: Remove hard-coded btf_vmlinux assumption from BPF verifier
selftests/bpf: Add CO-RE relocs selftest relying on kernel module BTF
selftests/bpf: Add support for marking sub-tests as skipped
selftests/bpf: Add bpf_testmod kernel module for testing
libbpf: Add kernel module BTF support for CO-RE relocations
libbpf: Refactor CO-RE relocs to not assume a single BTF object
libbpf: Add internal helper to load BTF data by FD
bpf: Keep module's btf_data_size intact after load
bpf: Fix bpf_put_raw_tracepoint()'s use of __module_address()
selftests/bpf: Add Userspace tests for TCP_WINDOW_CLAMP
bpf: Adds support for setting window clamp
samples/bpf: Fix spelling mistake "recieving" -> "receiving"
bpf: Fix cold build of test_progs-no_alu32
...
====================
Link: https://lore.kernel.org/r/20201204021936.85653-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Leon Romanovsky [Thu, 8 Oct 2020 13:06:37 +0000 (16:06 +0300)]
net/mlx5: Register mlx5 devices to auxiliary virtual bus
Create auxiliary devices under new virtual bus. This will replace
the custom-made mlx5 ->add()/->remove() interfaces and next patches
will fill the missing callback and remove the old interface logic.
The attachment of auxiliary drivers to the devices is possible in
1-to-1 manner only and it requires us to create device for every protocol,
so that device (module) will be able to connect to it.
System with 2 IB and 1 RoCE cards:
[leonro@vm ~]$ lspci |grep nox
00:09.0 Ethernet controller: Mellanox Technologies MT27800 Family [ConnectX-5]
00:0a.0 Ethernet controller: Mellanox Technologies MT28908 Family [ConnectX-6]
00:0b.0 Ethernet controller: Mellanox Technologies MT2910 Family [ConnectX-7]
[leonro@vm ~]$ ls -l /sys/bus/auxiliary/devices/
mlx5_core.eth.2 -> ../../../devices/pci0000:00/0000:00:0b.0/mlx5_core.eth.2
mlx5_core.rdma.0 -> ../../../devices/pci0000:00/0000:00:09.0/mlx5_core.rdma.0
mlx5_core.rdma.1 -> ../../../devices/pci0000:00/0000:00:0a.0/mlx5_core.rdma.1
mlx5_core.rdma.2 -> ../../../devices/pci0000:00/0000:00:0b.0/mlx5_core.rdma.2
mlx5_core.vdpa.1 -> ../../../devices/pci0000:00/0000:00:0a.0/mlx5_core.vdpa.1
mlx5_core.vdpa.2 -> ../../../devices/pci0000:00/0000:00:0b.0/mlx5_core.vdpa.2
[leonro@vm ~]$ rdma dev
0: ibp0s9: node_type ca fw 4.6.9999 node_guid 5254:00c0:fe12:3455 sys_image_guid 5254:00c0:fe12:3455
1: ibp0s10: node_type ca fw 4.6.9999 node_guid 5254:00c0:fe12:3456 sys_image_guid 5254:00c0:fe12:3456
2: rdmap0s11: node_type ca fw 4.6.9999 node_guid 5254:00c0:fe12:3457 sys_image_guid 5254:00c0:fe12:3457
System with RoCE SR-IOV card with 4 VFs:
[leonro@vm ~]$ lspci |grep nox
01:00.0 Ethernet controller: Mellanox Technologies MT28908 Family [ConnectX-6]
01:00.1 Ethernet controller: Mellanox Technologies MT28908 Family [ConnectX-6 Virtual Function]
01:00.2 Ethernet controller: Mellanox Technologies MT28908 Family [ConnectX-6 Virtual Function]
01:00.3 Ethernet controller: Mellanox Technologies MT28908 Family [ConnectX-6 Virtual Function]
01:00.4 Ethernet controller: Mellanox Technologies MT28908 Family [ConnectX-6 Virtual Function]
[leonro@vm ~]$ ls -l /sys/bus/auxiliary/devices/
mlx5_core.eth.0 -> ../../../devices/pci0000:00/0000:00:09.0/0000:01:00.0/mlx5_core.eth.0
mlx5_core.eth.1 -> ../../../devices/pci0000:00/0000:00:09.0/0000:01:00.1/mlx5_core.eth.1
mlx5_core.eth.2 -> ../../../devices/pci0000:00/0000:00:09.0/0000:01:00.2/mlx5_core.eth.2
mlx5_core.eth.3 -> ../../../devices/pci0000:00/0000:00:09.0/0000:01:00.3/mlx5_core.eth.3
mlx5_core.eth.4 -> ../../../devices/pci0000:00/0000:00:09.0/0000:01:00.4/mlx5_core.eth.4
mlx5_core.rdma.0 -> ../../../devices/pci0000:00/0000:00:09.0/0000:01:00.0/mlx5_core.rdma.0
mlx5_core.rdma.1 -> ../../../devices/pci0000:00/0000:00:09.0/0000:01:00.1/mlx5_core.rdma.1
mlx5_core.rdma.2 -> ../../../devices/pci0000:00/0000:00:09.0/0000:01:00.2/mlx5_core.rdma.2
mlx5_core.rdma.3 -> ../../../devices/pci0000:00/0000:00:09.0/0000:01:00.3/mlx5_core.rdma.3
mlx5_core.rdma.4 -> ../../../devices/pci0000:00/0000:00:09.0/0000:01:00.4/mlx5_core.rdma.4
mlx5_core.vdpa.1 -> ../../../devices/pci0000:00/0000:00:09.0/0000:01:00.1/mlx5_core.vdpa.1
mlx5_core.vdpa.2 -> ../../../devices/pci0000:00/0000:00:09.0/0000:01:00.2/mlx5_core.vdpa.2
mlx5_core.vdpa.3 -> ../../../devices/pci0000:00/0000:00:09.0/0000:01:00.3/mlx5_core.vdpa.3
mlx5_core.vdpa.4 -> ../../../devices/pci0000:00/0000:00:09.0/0000:01:00.4/mlx5_core.vdpa.4
[leonro@vm ~]$ rdma dev
0: rocep1s0f0: node_type ca fw 4.6.9999 node_guid 5254:00c0:fe12:3455 sys_image_guid 5254:00c0:fe12:3455
1: rocep1s0f0v0: node_type ca fw 4.6.9999 node_guid 0000:0000:0000:0000 sys_image_guid 5254:00c0:fe12:3456
2: rocep1s0f0v1: node_type ca fw 4.6.9999 node_guid 0000:0000:0000:0000 sys_image_guid 5254:00c0:fe12:3457
3: rocep1s0f0v2: node_type ca fw 4.6.9999 node_guid 0000:0000:0000:0000 sys_image_guid 5254:00c0:fe12:3458
4: rocep1s0f0v3: node_type ca fw 4.6.9999 node_guid 0000:0000:0000:0000 sys_image_guid 5254:00c0:fe12:3459
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Leon Romanovsky [Tue, 6 Oct 2020 09:34:25 +0000 (12:34 +0300)]
vdpa/mlx5: Make hardware definitions visible to all mlx5 devices
Move mlx5_vdpa IFC header file to the general include folder, so
mlx5_core will be able to reuse it to check if VDPA is supported
prior to creating an auxiliary device.
As part of this move, update the header file name to mlx5 general
naming scheme.
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Leon Romanovsky [Sun, 4 Oct 2020 11:30:58 +0000 (14:30 +0300)]
net/mlx5_core: Clean driver version and name
Remove exposed driver version as it was done in other drivers,
so module version will work correctly by displaying the kernel
version for which it is compiled.
And move mlx5_core module name to general include, so auxiliary drivers
will be able to use it as a basis for a name in their device ID tables.
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Leon Romanovsky [Thu, 15 Oct 2020 11:52:00 +0000 (14:52 +0300)]
net/mlx5: Properly convey driver version to firmware
mlx5 firmware expects driver version in specific format X.X.X, so
make it always correct and based on real kernel version aligned with
the driver.
Fixes:
012e50e109fd ("net/mlx5: Set driver version into firmware")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Leon Romanovsky [Fri, 4 Dec 2020 12:46:02 +0000 (14:46 +0200)]
Merge tag 'auxbus-5.11-rc1' of https://git./linux/kernel/git/gregkh/driver-core into mlx5-next
Auxiliary Bus support tag for 5.11-rc1
This is a signed tag for other subsystems to be able to pull in the
auxiliary bus support into their trees for the 5.11-rc1 merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'auxbus-5.11-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: auxiliary bus: minor coding style tweaks
driver core: auxiliary bus: make remove function return void
driver core: auxiliary bus: move slab.h from include file
Add auxiliary bus support
Greg Kroah-Hartman [Fri, 4 Dec 2020 11:49:28 +0000 (12:49 +0100)]
driver core: auxiliary bus: minor coding style tweaks
For some reason, the original aux bus patch had some really long lines
in a few places, probably due to it being a very long-lived patch in
development by many different people. Fix that up so that the two files
all have the same length lines and function formatting styles.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Ertman <david.m.ertman@intel.com>
Cc: Fred Oh <fred.oh@linux.intel.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: Leon Romanovsky <leonro@nvidia.com>
Cc: Martin Habets <mhabets@solarflare.com>
Cc: Parav Pandit <parav@mellanox.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Cc: Shiraz Saleem <shiraz.saleem@intel.com>
Link: https://lore.kernel.org/r/X8oiSFTpYHw1xE/o@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Fri, 4 Dec 2020 11:44:07 +0000 (12:44 +0100)]
driver core: auxiliary bus: make remove function return void
There's an effort to move the remove() callback in the driver core to
not return an int, as nothing can be done if this function fails. To
make that effort easier, make the aux bus remove function void to start
with so that no users have to be changed sometime in the future.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Ertman <david.m.ertman@intel.com>
Cc: Fred Oh <fred.oh@linux.intel.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: Leon Romanovsky <leonro@nvidia.com>
Cc: Martin Habets <mhabets@solarflare.com>
Cc: Parav Pandit <parav@mellanox.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Cc: Shiraz Saleem <shiraz.saleem@intel.com>
Link: https://lore.kernel.org/r/X8ohB1ks1NK7kPop@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Fri, 4 Dec 2020 11:43:47 +0000 (12:43 +0100)]
driver core: auxiliary bus: move slab.h from include file
No need to include slab.h in include/linux/auxiliary_bus.h, as it is not
needed there. Move it to drivers/base/auxiliary.c instead.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Ertman <david.m.ertman@intel.com>
Cc: Fred Oh <fred.oh@linux.intel.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: Leon Romanovsky <leonro@nvidia.com>
Cc: Martin Habets <mhabets@solarflare.com>
Cc: Parav Pandit <parav@mellanox.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Cc: Shiraz Saleem <shiraz.saleem@intel.com>
Link: https://lore.kernel.org/r/X8og8xi3WkoYXet9@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Ertman [Thu, 3 Dec 2020 00:54:24 +0000 (16:54 -0800)]
Add auxiliary bus support
Add support for the Auxiliary Bus, auxiliary_device and auxiliary_driver.
It enables drivers to create an auxiliary_device and bind an
auxiliary_driver to it.
The bus supports probe/remove shutdown and suspend/resume callbacks.
Each auxiliary_device has a unique string based id; driver binds to
an auxiliary_device based on this id through the bus.
Co-developed-by: Kiran Patil <kiran.patil@intel.com>
Co-developed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Co-developed-by: Fred Oh <fred.oh@linux.intel.com>
Co-developed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Fred Oh <fred.oh@linux.intel.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Shiraz Saleem <shiraz.saleem@intel.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Martin Habets <mhabets@solarflare.com>
Link: https://lore.kernel.org/r/20201113161859.1775473-2-david.m.ertman@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/160695681289.505290.8978295443574440604.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simon Wunderlich [Fri, 4 Dec 2020 07:41:16 +0000 (08:41 +0100)]
batman-adv: Drop unused soft-interface.h include in fragmentation.c
The commit
992b03b88e36 ("batman-adv: Don't always reallocate the
fragmentation skb head") removed the last user of functions from
soft-interface.h.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Sven Eckelmann [Mon, 17 Aug 2020 12:37:13 +0000 (14:37 +0200)]
batman-adv: Drop legacy code for auto deleting mesh interfaces
The only way to automatically drop batadv mesh interfaces when all soft
interfaces were removed was dropped with the sysfs support. It is no longer
needed to have them handled by kernel anymore.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Sven Eckelmann [Mon, 17 Aug 2020 11:42:29 +0000 (13:42 +0200)]
batman-adv: Drop deprecated debugfs support
The debugfs support in batman-adv was marked as deprecated by the commit
00caf6a2b318 ("batman-adv: Mark debugfs functionality as deprecated") and
scheduled for removal in 2021.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Sven Eckelmann [Mon, 17 Aug 2020 11:42:29 +0000 (13:42 +0200)]
batman-adv: Drop deprecated sysfs support
The sysfs in batman-adv support was marked as deprecated by the commit
42cdd521487f ("batman-adv: ABI: Mark sysfs files as deprecated") and
scheduled for removal in 2021.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Sven Eckelmann [Sun, 11 Oct 2020 10:25:24 +0000 (12:25 +0200)]
batman-adv: Allow selection of routing algorithm over rtnetlink
A batadv net_device is associated to a B.A.T.M.A.N. routing algorithm. This
algorithm has to be selected before the interface is initialized and cannot
be changed after that. The only way to select this algorithm was a module
parameter which specifies the default algorithm used during the creation of
the net_device.
This module parameter is writeable over
/sys/module/batman_adv/parameters/routing_algo and thus allows switching of
the routing algorithm:
1. change routing_algo parameter
2. create new batadv net_device
But this is not race free because another process can be scheduled between
1 + 2 and in that time frame change the routing_algo parameter again.
It is much cleaner to directly provide this information inside the
rtnetlink's RTM_NEWLINK message. The two processes would be (in regards of
the creation parameter of their batadv interfaces) be isolated. This also
eases the integration of batadv devices inside tools like network-manager
or systemd-networkd which are not expecting to operate on /sys before a new
net_device is created.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Sven Eckelmann [Sun, 11 Oct 2020 10:25:23 +0000 (12:25 +0200)]
batman-adv: Prepare infrastructure for newlink settings
The batadv generic netlink family can be used to retrieve the current state
and set various configuration settings. But there are also settings which
must be set before the actual interface is created.
The rtnetlink already uses IFLA_INFO_DATA to allow net_device families to
transfer such configurations. The minimal required functionality for this
is now available for the batadv rtnl_link_ops. Also a new IFLA class of
attributes will be attached to it because rtnetlink only allows 51
different attributes but batadv_nl_attrs already contains 62 attributes.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Sven Eckelmann [Mon, 26 Oct 2020 20:01:59 +0000 (21:01 +0100)]
batman-adv: Add new include for min/max helpers
The commit
b296a6d53339 ("kernel.h: split out min()/max() et al. helpers")
moved the min/max helper functionality from kernel.h to minmax.h. Adjust
the kernel code accordingly to avoid fragile indirect includes.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>