OSDN Git Service
Laurent Pinchart [Sun, 6 Dec 2020 23:03:09 +0000 (00:03 +0100)]
media: doc: pixfmt-yuv: Document subsampling in more details
Document YUV subsampling, including chroma spatial siting, and replace
the siting examples in individual formats by references to the common
documentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Laurent Pinchart [Sun, 6 Dec 2020 23:03:08 +0000 (00:03 +0100)]
media: doc: pixfmt-rgb: Replace '-' with 'X' to denote padding
Using '-' to represent padding bits and bytes make text and tables more
difficult to read. Use 'x' and 'X' instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Laurent Pinchart [Sun, 6 Dec 2020 23:03:07 +0000 (00:03 +0100)]
media: doc: pixfmt-rgb: Make 8 bits per component table more compact
All formats using 8 bits per component can be described with a byte
granularity instead of a bit granularity without loss of precision. This
makes the corresponding table more compact and easier to read.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Laurent Pinchart [Sun, 6 Dec 2020 23:03:06 +0000 (00:03 +0100)]
media: doc: pixfmt-rgb: Clarify naming scheme for RGB formats
The naming scheme for the RGB pixel formats has been developed
organically, and isn't consistent between formats using less than 8 bits
per pixels (mostly stored in 1 or 2 bytes per pixel, except for RGB666
that uses 4 bytes per pixel) and formats with 8 bits per pixel (stored
in 3 or 4 bytes). For the latter category, the names use a components
order convention that is the opposite of the first category, and the
opposite of DRM pixel formats. This has led to lots of confusion in the
past, and would really benefit from being explained more precisely. Do
so, which also prepares for the addition of additional RGB pixels
formats.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Laurent Pinchart [Sun, 6 Dec 2020 23:03:05 +0000 (00:03 +0100)]
media: doc: pixfmt-rgb: Add title for deprecated formats
Improve readability of the documentation by adding a section title for
the deprecated formats.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Laurent Pinchart [Sun, 6 Dec 2020 23:03:04 +0000 (00:03 +0100)]
media: doc: pixfmt-rgb: Remove layout table for packed RGB formats
The packed RGB formats documentation includes a layout table without any
context. This doesn't bring much useful information, and is confusing at
best. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Laurent Pinchart [Sun, 6 Dec 2020 23:03:03 +0000 (00:03 +0100)]
media: videodev2.h: Move HM12 format to YUV semi-planar section
V4L2_PIX_FMT_HM12 is a YUV semi-planar macro-block format. Move it from
the packed YUV formats section where it was misplaced to the YUV
semi-planar formats section.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Laurent Pinchart [Sun, 6 Dec 2020 23:03:02 +0000 (00:03 +0100)]
media: videodev2.h: Move HI240 format to vendor-specific section
V4L2_PIX_FMT_HI240 is a 8-bit dithered RGB format specific to BTTV. Move
it from the packed YUV formats section where it was misplaced to the
vendor-specific formats section.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Laurent Pinchart [Sun, 6 Dec 2020 23:03:01 +0000 (00:03 +0100)]
media: videodev2.h: Remove unneeded comment about 4CC value
The V4L2_PIX_FMT_BGRA444 format has a comment that explains why its 4CC
value is GA12. This explains the development history and isn't of much
interest to readers, it should have been part of a commit message
instead. Drop the comment, anyone interested in history can turn to git.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Fri, 4 Dec 2020 11:46:56 +0000 (12:46 +0100)]
media: ccs: Fix return value from probe
rval wasn't set, resulting in probe returning zero instead of an error.
Fixes:
de10c1619c48 ("[media] smiapp: Get clock rate if it's not available through DT")
Reported-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Arnd Bergmann [Thu, 3 Dec 2020 22:28:16 +0000 (23:28 +0100)]
media: ccs: avoid printing an uninitialized variable
There is no intialization for the 'reg' variable, so printing
it produces undefined behavior as well as a compile-time warning:
drivers/media/i2c/ccs/ccs-core.c:314:49: error: variable 'reg' is uninitialized when used here [-Werror,-Wuninitialized]
"0x%8.8x %s pixels: %d %s (pixelcode %u)\n", reg,
Remove the variable and stop printing it.
Fixes:
fd9065812c7b ("media: smiapp: Obtain frame descriptor from CCS limits")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Arnd Bergmann [Fri, 4 Dec 2020 08:20:14 +0000 (09:20 +0100)]
media: i2c: fix an uninitialized error code
Clang points out that the error handling in ov02a10_s_stream() is
broken, and just returns a random error code:
drivers/media/i2c/ov02a10.c:537:6: warning: variable 'ret' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (ov02a10->streaming == on)
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/i2c/ov02a10.c:568:9: note: uninitialized use occurs here
return ret;
^~~
drivers/media/i2c/ov02a10.c:537:2: note: remove the 'if' if its condition is always false
if (ov02a10->streaming == on)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
If streaming is already on, leave it that way and return success.
Suggested-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Fixes:
91807efbe8ec ("media: i2c: add OV02A10 image sensor driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Wed, 2 Dec 2020 18:09:54 +0000 (19:09 +0100)]
media: Revert "media: dt-bindings: media: Use OF graph schema"
This reverts commit
f61eb7bc9256aeb173d2d730f59cdd569d261c52.
While aligning with the OF graph schema will be done for the media DT
bindings, this patch got merged a little too hastily. Revert it for now.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Jonas Karlman [Fri, 27 Nov 2020 04:56:27 +0000 (05:56 +0100)]
media: rc: add keymap for pine64 remote
Add a keymap for the pine64 IR remote [0]. The mouse key has been mapped to
KEY_EPG to provide a more useful remote.
[0] http://files.pine64.org/doc/Pine%20A64%20Schematic/remote-wit-logo.jpg
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Thu, 3 Dec 2020 12:50:33 +0000 (13:50 +0100)]
media: pixfmt-meta-rkisp1.rst: fix two build warnings
With Sphinx 2.x: those two warnings are produced:
/devel/v4l/docs/sphinx2/Documentation/output/videodev2.h.rst:6: WARNING: undefined label: v4l2-meta-fmt-rk-isp1-params (if the link has no caption the label must precede a section header)
/devel/v4l/docs/sphinx2/Documentation/output/videodev2.h.rst:6: WARNING: undefined label: v4l2-meta-fmt-rk-isp1-stat-3a (if the link has no caption the label must precede a section header)
The reason is that there's no blank line between the two
identifiers.
Fixes:
3f46cac6787f ("media: admin-guide/pixfmt-meta-rkisp1.rst: pixfmt reference conforming with macro")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hans Verkuil [Thu, 26 Nov 2020 13:27:17 +0000 (14:27 +0100)]
media: userspace-api/media: finalize stateless FWHT codec docs
Document V4L2_CTRL_TYPE_FWHT_PARAMS and p_fwht_params. Also
improve the V4L2_PIX_FMT_FWHT_STATELESS description.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hans Verkuil [Thu, 26 Nov 2020 13:27:16 +0000 (14:27 +0100)]
media: vidioc-g-ext-ctrls.rst: add missing 'struct' before the types
Add 'struct' to clarify that these are pointers to structs.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hans Verkuil [Thu, 26 Nov 2020 13:12:03 +0000 (14:12 +0100)]
media: pixfmt-compressed.rst: fix 'bullet' formatting
Drop the 'bullets' for the HEVC stateless codec documentation.
It doesn't work, and they just show up as asterisks.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hans Verkuil [Thu, 26 Nov 2020 13:08:36 +0000 (14:08 +0100)]
media: ext-ctrls-codec.rst: move FWHT docs to ext-ctrls-codec-stateless.rst
Move the documentation for the stateless FWHT codec to
ext-ctrls-codec-stateless.rst since that is the proper place
for the stable stateless API documentation.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hans Verkuil [Thu, 26 Nov 2020 13:02:18 +0000 (14:02 +0100)]
media: vicodec: mark the stateless FWHT API as stable
The FWHT stateless 'uAPI' was staging and marked explicitly in the
V4L2 specification that it will change and is unstable.
Note that these control IDs were never exported as a public API,
they were only defined in kernel-local headers (fwht-ctrls.h).
Now, the FWHT stateless controls is ready to be part
of the stable uAPI.
While not too late:
- Rename V4L2_CID_MPEG_VIDEO_FWHT_PARAMS to V4L2_CID_STATELESS_FWHT_PARAMS.
- Move the contents of fwht-ctrls.h to v4l2-controls.h.
- Move the public parts of drivers/media/test-drivers/vicodec/codec-fwht.h
to v4l2-controls.h.
- Add V4L2_CTRL_TYPE_FWHT_PARAMS control initialization and validation.
- Add p_fwht_params to struct v4l2_ext_control.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hans Verkuil [Thu, 26 Nov 2020 12:58:20 +0000 (13:58 +0100)]
media: vicodec: add V4L2_ prefix before FWHT_VERSION and FWHT_FL_*
The FWHT stateless 'uAPI' was staging and marked explicitly in the
V4L2 specification that it will change and is unstable.
Note that these control IDs were never exported as a public API,
they were only defined at the driver's code.
While not too late, let's rename them is preparation for promoting
the stateless FWHT codec API as a public API.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hans Verkuil [Wed, 25 Nov 2020 10:19:06 +0000 (11:19 +0100)]
media: ext-ctrls-image-source.rst: document v4l2_area
The v4l2_area struct was not documented in the media documentation,
which meant that references to that struct elsewhere in the documentation
never linked to anything.
[mchehab: remove .. cssclass:: longtable]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Helen Koike [Wed, 18 Nov 2020 14:24:00 +0000 (15:24 +0100)]
media: admin-guide/pixfmt-meta-rkisp1.rst: pixfmt reference conforming with macro
Fix warnings from make htmlddocs:
Documentation/output/videodev2.h.rst:6: WARNING: undefined label: v4l2-meta-fmt-rk-isp1-params (if the link has no caption the label must precede a section header)
Documentation/output/videodev2.h.rst:6: WARNING: undefined label: v4l2-meta-fmt-rk-isp1-stat-3a (if the link has no caption the label must precede a section header)
Fixes:
df22026aebd8 ("media: videodev2.h, v4l2-ioctl: add rkisp1 meta buffer format")
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Thu, 26 Nov 2020 09:36:18 +0000 (10:36 +0100)]
media: docs: Move the H264 stateless codec uAPI
Now that we've destaged the H264 stateless codec controls,
and with all the pieces in place, update the documentation
and move it to its own section.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Thu, 26 Nov 2020 09:36:17 +0000 (10:36 +0100)]
media: uapi: move H264 stateless controls out of staging
The H.264 stateless 'uAPI' was staging and marked explicitly in the
V4L2 specification that it will change and is unstable.
Note that these control IDs were never exported as a public API,
they were only defined in kernel-local headers (h264-ctrls.h).
Now, the H264 stateless controls is ready to be part
of the stable uAPI.
While not too late, let's rename them and re-number their
control IDs, moving them to the newly created stateless
control class, and updating all the drivers accordingly.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Thu, 26 Nov 2020 09:36:16 +0000 (10:36 +0100)]
media: controls: Log H264 stateless controls in .std_log
For now, only print the type of the control. In the future,
we might want to be able to print the values of all
the stateless codec controls currently set in the control handler,
which should be useful for debugging reasons.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Thu, 26 Nov 2020 09:36:15 +0000 (10:36 +0100)]
media: uapi: Move the H264 stateless control types out of staging
Move the H264 stateless control types out of staging,
and re-number them to avoid any confusion.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Thu, 26 Nov 2020 09:36:14 +0000 (10:36 +0100)]
media: doc: Replace symbol for V4L2_CTRL_TYPE_H264_PRED_WEIGHTS
When V4L2_CTRL_TYPE_H264_PRED_WEIGHTS was added, adding a replace
symbol directive in videodev2.h.rst.exceptions was missed.
Now that the control type is destaged, it's important to fix this.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Thu, 26 Nov 2020 09:36:13 +0000 (10:36 +0100)]
media: uapi: Move parsed H264 pixel format out of staging
Since we are ready to stabilize the H264 stateless API,
start by first moving the parsed H264 pixel format.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Thu, 26 Nov 2020 09:36:12 +0000 (10:36 +0100)]
media: controls: Add the stateless codec control class
Add a new control class to hold the stateless codecs controls
that are ready to be moved out of staging.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Thu, 26 Nov 2020 09:36:11 +0000 (10:36 +0100)]
media: controls: Validate H264 stateless controls
Check that all the fields that correspond or are related
to a H264 specification syntax element have legal values.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Thu, 26 Nov 2020 09:36:10 +0000 (10:36 +0100)]
media: Clean stateless control includes
Avoid including h264-ctrls.h, vp8-ctrls.h, etc,
and instead just include v4l2-ctrls.h which does the right
thing.
This is in preparation for moving the stateless controls
out of staging, which will mean removing some of these headers.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Thu, 26 Nov 2020 09:36:09 +0000 (10:36 +0100)]
media: Rename stateful codec control macros
For historical reasons, stateful codec controls are named
as {}_MPEG_{}. While we can't at this point sanely
change all control IDs (such as V4L2_CID_MPEG_VIDEO_VP8_FRAME_HEADER),
we can least change the more meaningful macros such as classes
macros.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Thu, 26 Nov 2020 09:36:08 +0000 (10:36 +0100)]
media: cedrus: h264: Support profile controls
Cedrus supports H.264 profiles from Baseline to High,
except for the Extended profile
Expose the V4L2_CID_MPEG_VIDEO_H264_PROFILE so that
userspace can query the driver for the supported
profiles and levels.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Jonas Karlman [Thu, 26 Nov 2020 09:36:07 +0000 (10:36 +0100)]
media: rkvdec: h264: Support profile and level controls
The Rockchip Video Decoder used in RK3399 supports H.264 profiles from
Baseline to High 4:2:2 up to Level 5.1, except for the Extended profile.
Expose the V4L2_CID_MPEG_VIDEO_H264_PROFILE and the
V4L2_CID_MPEG_VIDEO_H264_LEVEL control, so that userspace can query the
driver for the list of supported profiles and level.
For now, we don't expose 4:2:2 since the driver doesn't
implement the required support.
[Ezequiel: Don't expose 4:2:2 profile for now]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Thu, 26 Nov 2020 09:36:06 +0000 (10:36 +0100)]
media: controls: Add validate failure debug message
Add a debug message for control validation (validate_new)
failures. This is useful to debug issues with ioctls such
as VIDIOC_TRY_EXT_CTRLS and VIDIOC_S_EXT_CTRLS.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hans Verkuil [Thu, 26 Nov 2020 09:36:05 +0000 (10:36 +0100)]
media: vidioc-g-ext-ctrls.rst: document V4L2_CTRL_CLASS_DETECT
V4L2_CTRL_CLASS_DETECT was never documented here, add it.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Mon, 23 Nov 2020 15:00:19 +0000 (16:00 +0100)]
media: controls: Add VP8 stateless type initialization
The VP8_FRAME_HEADER control type is validated, so it
needs a corresponding initialization to produce default
legal values.
For now, only add the minimum required initialization
to satisfy current validation.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Tue, 6 Oct 2020 13:05:25 +0000 (15:05 +0200)]
media: ccs: Use all regulators
Use regulators vio and vcore besides vana. The regulators were always
there but on many boards they've been hard wired. Control them explicitly
now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Mon, 5 Oct 2020 21:36:52 +0000 (23:36 +0200)]
media: dt-bindings: mipi,ccs: Add vcore and vio supplies
Vcore and vio supplies are also part of the spec and used by many sensors.
Do not specify the voltages as they are generally sensor dependent.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Mon, 5 Oct 2020 21:36:00 +0000 (23:36 +0200)]
media: dt-bindings: mipi,ccs: Don't mention vana voltage
It was mentioned vana voltage is typically 2,8 volts. This is truly sensor
dependent, and nowadays 2,8 volts is a lot.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Mon, 5 Oct 2020 21:17:12 +0000 (23:17 +0200)]
media: ccs: Remove unnecessary delays from power-up sequence
SMIA nor CCS need these delays; remove them.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Mon, 21 Sep 2020 16:08:20 +0000 (18:08 +0200)]
media: ccs: Use longer pre-I²C sleep for CCS compliant devices
Longer idle period is required on I²C bus before the first transaction
after lifting xshutdown.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Fri, 18 Sep 2020 09:36:38 +0000 (11:36 +0200)]
media: ccs: Wrap long lines, unwrap short ones
Over the years (and renaming) some lines that may well be wrapped ended up
being over 80 characters, likewise there are shorter lines that can be
merged. Do that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Fri, 18 Sep 2020 09:23:39 +0000 (11:23 +0200)]
media: ccs: Clean up runtime PM usage
If pm_runtime_get_sync() fails, there's no need to set the device active
again. Also, in the same case to return the usage_count to zero,
pm_runtime_put_noidle() is enough.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Thu, 3 Sep 2020 19:52:29 +0000 (21:52 +0200)]
media: ccs: Use static data read-only registers
Access read-only registers from CCS static data.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Thu, 3 Sep 2020 09:32:56 +0000 (11:32 +0200)]
media: ccs: Add support for manufacturer regs from sensor and module files
Write manufacturer specific registers (MSRs) from file to the sensor on
sensor power-on.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Fri, 13 Nov 2020 15:07:28 +0000 (16:07 +0100)]
media: ccs: Allow range in between I²C retries
Make the delay between I²C access retries a range between 1 and 2 ms. Also
make the number of retries 10 instead of 5, in order not to reduce the
total amount of time.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Wed, 24 Jun 2020 21:57:46 +0000 (23:57 +0200)]
media: ccs: Change my e-mail address
Use my @linux.intel.com e-mail address in the CCS driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Fri, 2 Oct 2020 11:36:14 +0000 (13:36 +0200)]
media: ccs-pll: Fix MODULE_LICENSE
Change MODULE_LICENSE to "GPL v2" as indicated by the SPDX tag.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Wed, 27 May 2020 21:59:40 +0000 (23:59 +0200)]
media: smiapp-pll: Rename as ccs-pll
MIPI CCS replaces SMIA and SMIA++ as the current standard. CCS brings new
features while existing functionality will be supported. Rename the
smiapp-pll as ccs-pll accordingly.
Also add Intel copyright to the files.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Wed, 24 Jun 2020 13:39:05 +0000 (15:39 +0200)]
media: ccs: Read ireal numbers correctly
Some limit values are available in q16.q16 format, referred to as 32-bit
unsigned ireal in CCS. Read these correctly.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Wed, 2 Sep 2020 10:46:59 +0000 (12:46 +0200)]
media: ccs: Move limit value real to integer conversion from read to access time
Instead of converting the limit values at register read time, do that at
access time instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Wed, 2 Sep 2020 10:23:40 +0000 (12:23 +0200)]
media: ccs: Make real to integer number conversion optional
The limit values will be raw soon, and the conversion takes place later
on. Prepare for that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Wed, 2 Sep 2020 10:09:03 +0000 (12:09 +0200)]
media: ccs: Refactor register reading a little
Rework quirk and 8-bit only access functions with a single function that
takes arguments. This is later extensible to support yet more flags.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Wed, 27 May 2020 23:00:29 +0000 (01:00 +0200)]
media: ccs: Replace somewhat harsh internal checks based on BUG with WARN_ON
If an internal driver error was encountered, BUG was issued. Instead, do
less harsh WARN_ON_ONCE and try to manage with the consequences.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Wed, 27 May 2020 23:02:07 +0000 (01:02 +0200)]
media: ccs: The functions to get compose or crop rectangle never return NULL
The NULL check is not needed as the functions do not return NULL. Remove
the check (and BUG).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Wed, 27 May 2020 08:35:01 +0000 (10:35 +0200)]
media: ccs: Stop reading arrays after the first zero
The register arrays have a certain size but not all the entries will be
relevant. In practice reading can be stopped after encountering a zero
value in the array. Do that to avoid extra reads.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Fri, 14 Feb 2020 13:49:42 +0000 (14:49 +0100)]
media: ccs: Read CCS static data from firmware binaries
Read the CCS static data for sensors and modules. The files are expected
to be found in "ccs" directory.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Fri, 14 Feb 2020 13:14:18 +0000 (14:14 +0100)]
media: ccs: Combine revision number major and minor into one
The module revision number major and minor are both 8 bits while the
sensor revision number is 16 bits. Combine the module revision into one
number.
This also adds printing the lowest 8 bits of the module version through
the sysfs attribute.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Fri, 14 Feb 2020 09:00:35 +0000 (10:00 +0100)]
media: ccs: Add CCS static data parser library
Add a parser library for parsing the CCS static data format.
The library may be also compiled in user space as the format has uses also
in the user space. Therefore it is dual licensed under the 3-clause BSD
license as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Wed, 30 Sep 2020 16:20:42 +0000 (18:20 +0200)]
media: ccs: Fix obtaining bus information from firmware
Let v4l2_fwnode_endpoint_alloc_parse to figure out the type of the data
bus. As the old bindings did not require the "bus-type" property, we need
to rely on guessing between CSI-2 D-PHY and CCP2. Setting the type to
CSI-2 D-PHY will parse just that and succeed even if no data-lanes are
set.
Also add a comment on the matter to the driver to avoid breaking this in
the future.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Tue, 11 Feb 2020 21:41:39 +0000 (22:41 +0100)]
media: ccs: Make hwcfg part of the device specific struct
There's no need to allocate the hardware configuration struct separately.
Put it in struct ccs_sensor.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Tue, 11 Feb 2020 21:35:40 +0000 (22:35 +0100)]
media: ccs: Remove remaining support for platform data
No need to support platform data; remove support for conveying hardware
configuration that way.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Tue, 11 Feb 2020 21:32:36 +0000 (22:32 +0100)]
media: ccs: Remove the I²C ID table
The I²C ID table is no longer needed; remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Mon, 3 Feb 2020 11:44:35 +0000 (12:44 +0100)]
media: ccs: Add CCS ACPI device ID
The CCS compliant sensors use device ID "MIPI0200". Use this id for ACPI
device matching.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Mon, 21 Sep 2020 16:04:47 +0000 (18:04 +0200)]
media: ccs: Add device compatible identifiers for telling SMIA and CCS apart
Add device data specific to DT compatible ID to tell SMIA and CCS devices
apart already in power-up.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Tue, 11 Feb 2020 21:31:51 +0000 (22:31 +0100)]
media: ccs: Add MIPI CCS compatible strings
Add "mipi-ccs-1.0" and "mipi-ccs-1.1" compatible strings to the CCS
driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Wed, 2 Dec 2020 14:18:19 +0000 (15:18 +0100)]
media: Documentation: ccs: Reorder SPDX and copyright notice lines
Move the SPDX tag to the top, placing the copyright notice after that.
This aligns the file with existing practices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Wed, 2 Dec 2020 14:16:57 +0000 (15:16 +0100)]
media: Documentation: ccs: Rename ccs-regs.txt as ccs-regs.asc
As documentation used to be in .txt files before converting to ReST,
rename ccs-regs.txt to avoid it being taken as documentation that
pre-dates ReST conversion and so target for further conversion to ReST.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Dan Carpenter [Tue, 1 Dec 2020 14:30:58 +0000 (15:30 +0100)]
media: rockchip: rkisp1: remove useless debugfs checks
The debugfs_create_dir() function never returns NULLs so this code will
never be executed. It's not intended that callers will check for
debugfs errors in the normal case and it's not necessary in this driver,
so we can just delete this code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Jonathan Corbet [Mon, 30 Nov 2020 22:52:21 +0000 (23:52 +0100)]
media: stop pretending to maintain cafe and ov7670
It's been a long time since I could credibly claim to be maintaining these
drivers; I'm not even sure my hardware works anymore. Mark them orphan.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Christophe JAILLET [Sun, 29 Nov 2020 12:30:11 +0000 (13:30 +0100)]
media: saa7146: switch from 'pci_' to 'dma_' API
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.
When memory is allocated in 'saa7146_pgtable_alloc()' GFP_KERNEL can be
used because the callers are either .buf_prepare functions or function that
already use GFP_KERNEL (hidden in a 'vmalloc_32()' call).
When memory is allocated in 'saa7146_init_one()' GFP_KERNEL can be used
because it is probe function and no lock is taken in the between.
When memory is allocated in 'saa7146_vv_init()' GFP_KERNEL can be used
because this function already uses GFP_KERNEL and no lock is taken in the
between.
When memory is allocated in 'vbi_workaround()' GFP_KERNEL can be used
because it is only called from a .open function.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Christophe JAILLET [Fri, 27 Nov 2020 20:58:01 +0000 (21:58 +0100)]
media: ttpci: switch from 'pci_' to 'dma_' API
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.
When memory is allocated in 'av7110_attach()' GFP_KERNEL can be used
because this flag is already used above in the same function and no lock is
taken in the between.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Christophe JAILLET [Fri, 27 Nov 2020 20:34:40 +0000 (21:34 +0100)]
media: solo6x10: switch from 'pci_' to 'dma_' API
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.
When memory is allocated in 'snd_solo_pcm_open()' (solo6x10-g723.c)
GFP_KERNEL can be used because this flag is already used jew a few lines
above.
When memory is allocated in 'solo_enc_alloc()' (solo6x10-v4l2-enc.c)
GFP_KERNEL can be used because this flag is already used jew a few lines
above.
When memory is allocated in 'solo_enc_v4l2_init()' (solo6x10-v4l2-enc.c)
GFP_KERNEL can be used because calls 'solo_enc_alloc()' which already uses
this flag.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Tom Rix [Fri, 27 Nov 2020 16:44:08 +0000 (17:44 +0100)]
media: si4713: remove trailing semicolon in macro definition
The macro use will already have a semicolon.
[hverkuil: also add () around p in the macro]
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fabio Estevam [Fri, 27 Nov 2020 16:09:45 +0000 (17:09 +0100)]
media: staging/imx: Increase IMX_MEDIA_EOF_TIMEOUT
When trying to capture video on a imx6dl-based board with an ADV7280,
the following timeout error is observed:
v4l2-ctl --stream-mmap -d /dev/video2
[ 22.792049] ipu1_csi1: EOF timeout
VIDIOC_DQBUF: failed: Input/output error
Increase the IMX_MEDIA_EOF_TIMEOUT to avoid such problem.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Andrey Konovalov [Thu, 26 Nov 2020 15:01:57 +0000 (16:01 +0100)]
media: camss: Make use of V4L2_CAP_IO_MC
Implement mbus_code filtering for format enumeration.
Without this patch libcamera errors out with:
"ERROR V4L2 v4l2_videodevice.cpp:982 /dev/video0[cap]: Media bus code
filtering not supported by the device"
This is the second version of this change which handles the case of
several pixel formats corresponding to one media bus format correctly.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Andrey Konovalov [Thu, 26 Nov 2020 15:01:56 +0000 (16:01 +0100)]
media: Revert "media: camss: Make use of V4L2_CAP_IO_MC"
This reverts commit
c90f1178dcac30dee5ddd29ec0513e7589aa866e.
The assumption of "Each entry in formats[] table has unique mbus_code"
is valid for the RDI entities, but not for the PIX ones.
Reverting this patch and creating a new one which handles the PIX entities
correctly results in smaller and more straightforward patch than doing the
changes on top of the current version.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Peilin Ye [Thu, 26 Nov 2020 12:21:48 +0000 (13:21 +0100)]
media: rockchip: rkisp1: Fix typos in comments and macro definitions
Fix 4 typos under drivers/media/platform/rockchip/rkisp1/ found by
checkpatch, including the RKISP1_CIF_MI_{M,S}P_PINGPONG_ENABLE macro
definitions.
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Jacopo Mondi [Thu, 26 Nov 2020 07:47:56 +0000 (08:47 +0100)]
media: rcar-vin: Remove unused macro
The VNCSI_IFMD_CSI_CHSEL_MASK is not used: remove it.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fabio Estevam [Wed, 25 Nov 2020 12:04:47 +0000 (13:04 +0100)]
media: fsl-viu: Use the ioread/write32be() accessors
Since commit
29d750686331 ("media: fsl-viu: allow building it with
COMPILE_TEST") there were several attempts to fix build failures on
PPC, MICROBLAZE and M68K.
However, such errors are still present as reported by kbuild robot.
Fix the problem by using the ioread/write32be() accessors, which build
fine on all platforms.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Marek Szyprowski [Tue, 24 Nov 2020 08:41:28 +0000 (09:41 +0100)]
media: platform: exynos4-is: remove all references to physical addresses
This driver always operates on the DMA/IOVA addresses, so calling them
physical addresses is misleading, although when no IOMMU is used they
equal each other. Fix this by renaming all such entries to 'addr' and
adjusting comments.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Niklas Söderlund [Sun, 22 Nov 2020 16:36:37 +0000 (17:36 +0100)]
media: adv748x: Configure device when resuming from sleep
If the device is powered off (for example during system suspend to ram)
the devices loses its configuration, especially the slave i2c mappings
and other configuration set at probe time. This renders the device
unusable and the only way to recover is to unbind and rebind the device
to the driver to run the probe setup again.
Add an early resume callback that reinitializes the device and setup the
slave i2c address mappings and other probe time configuration.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Niklas Söderlund [Sun, 22 Nov 2020 16:36:36 +0000 (17:36 +0100)]
media: adv748x: csi2: Set virtual channel when device is reset
It's not enough to set the CSI-2 virtual channel for TXA and TXB during
probe: it also needs to be set when the device is reset. Move the virtual
channel selection to adv748x_reset() that is called during probe and
when the device needs to be reset.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Niklas Söderlund [Sun, 22 Nov 2020 16:36:35 +0000 (17:36 +0100)]
media: adv748x: afe: Select input port when device is reset
It's not enough to select the AFE input port during probe: it also needs
to be set when the device is reset. Move the port selection to
adv748x_reset() that is called during probe and when the device needs to
be reset.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Niklas Söderlund [Sun, 22 Nov 2020 16:30:48 +0000 (17:30 +0100)]
media: adv748x: Only set i2c addresses once during probe
During probe the i2c slave addresses are set two times in a row, once in
adv748x_initialise_clients() and once directly after in adv748x_reset().
Remove the call to adv748x_set_slave_addresses() in
adv748x_initialise_clients() as it's only called during probe while
adv748x_reset() is called during probe and normal operation.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Dan Carpenter [Tue, 17 Nov 2020 07:23:40 +0000 (08:23 +0100)]
media: saa7146: fix array overflow in vidioc_s_audio()
The "a->index" value comes from the user via the ioctl. The problem is
that the shift can wrap resulting in setting "mxb->cur_audinput" to an
invalid value, which later results in an array overflow.
Fixes:
6680427791c9 ("[media] mxb: fix audio handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Christian Hewitt [Mon, 16 Nov 2020 04:30:55 +0000 (05:30 +0100)]
media: meson: vdec: add G12/SM1 to module description
The meson vdec driver also supports Amlogic G12/SM1 hardware.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Baskov Evgeniy [Fri, 13 Nov 2020 16:06:25 +0000 (17:06 +0100)]
media: s5p-jpeg: handle error condition in s5p_jpeg_probe
If an error happens in jpeg_get_drv_data(), i.e. match fails,
jpeg->variant field is NULL, so we cannot access it.
Consider device probe failed if jpeg->variant is NULL.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Baskov Evgeniy <baskov@ispras.ru>
Acked-by: Andrzej Pietrasiewicz <andrzejtp2010@gmail.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Jernej Skrabec [Tue, 10 Nov 2020 22:35:40 +0000 (23:35 +0100)]
media: cedrus: Add support for VP8 decoding
VP8 in Cedrus shares same engine as H264.
Note that it seems necessary to call bitstream parsing functions,
to parse frame header, otherwise decoded image is garbage. This is
contrary to what is driver supposed to do. However, values are not
really used, so this might be acceptable. It's possible that bitstream
parsing functions set some internal VPU state, which is later necessary
for proper decoding. Biggest suspect is "VP8 probs update" trigger.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Emmanuel Gil Peyrot [Mon, 9 Nov 2020 16:22:44 +0000 (17:22 +0100)]
media: hantro: Use VP8 lengths defined in uapi
Use the new defines instead of hardcoding the VP8 lengths.
[hverkuil: add commit log]
Signed-off-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Emmanuel Gil Peyrot [Mon, 9 Nov 2020 16:22:43 +0000 (17:22 +0100)]
media: uapi: Expose VP8 probability lengths as defines
These values will be used by various drivers implementing the VP8
stateless API.
This had been suggested by Ezequiel Garcia for the Cedrus VP8 driver.
Signed-off-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Irui Wang [Thu, 29 Oct 2020 01:17:21 +0000 (02:17 +0100)]
media: mtk-vpu: dump VPU status when IPI times out
when IPI time out, dump VPU status to get more debug information
Signed-off-by: Irui Wang <irui.wang@mediatek.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Irui Wang [Thu, 29 Oct 2020 01:17:20 +0000 (02:17 +0100)]
media: mtk-vpu: VPU should be in idle state before system is suspended
VPU should be in idle state before system is suspended
or it will work abnormally like VPU program counter not
in a correct address or VPU reset
Signed-off-by: Irui Wang <irui.wang@mediatek.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fabio Estevam [Wed, 2 Dec 2020 14:13:26 +0000 (15:13 +0100)]
media: coda: Convert the driver to DT-only
Since 5.10-rc1 i.MX is a devicetree-only platform, so simplify the code
by removing the unused non-DT support.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Zhang Xiaoxu [Mon, 16 Nov 2020 14:18:01 +0000 (15:18 +0100)]
media: tvp5150: Fix wrong return value of tvp5150_parse_dt()
If of_graph_get_endpoint_by_regs() return NULL, it will return 0 rather
than an errno, because we doesn't initialize the return value.
Fixes:
0556f1d580d4 ("media: tvp5150: add input source selection of_graph support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Xu Wang [Fri, 13 Nov 2020 07:21:11 +0000 (08:21 +0100)]
media: cx88: use ARRAY_SIZE
Use ARRAY_SIZE instead of dividing sizeof array with sizeof an element
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Martin Cerveny [Mon, 16 Nov 2020 12:56:15 +0000 (13:56 +0100)]
media: cedrus: Add support for V3s
V3s video engine runs at lower speed and support video decoder
for H.264 and JPEG/MJPEG only.
Signed-off-by: Martin Cerveny <m.cerveny@computer.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Martin Cerveny [Mon, 16 Nov 2020 12:56:16 +0000 (13:56 +0100)]
media: dt-bindings: media: cedrus: Add V3s compatible
Allwinner V3s SoC contains video engine. Add compatible for it.
Signed-off-by: Martin Cerveny <m.cerveny@computer.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>