OSDN Git Service
Eric Dumazet [Thu, 14 Oct 2021 17:59:18 +0000 (10:59 -0700)]
fq_codel: implement L4S style ce_threshold_ect1 marking
Add TCA_FQ_CODEL_CE_THRESHOLD_ECT1 boolean option to select Low Latency,
Low Loss, Scalable Throughput (L4S) style marking, along with ce_threshold.
If enabled, only packets with ECT(1) can be transformed to CE
if their sojourn time is above the ce_threshold.
Note that this new option does not change rules for codel law.
In particular, if TCA_FQ_CODEL_ECN is left enabled (this is
the default when fq_codel qdisc is created), ECT(0) packets can
still get CE if codel law (as governed by limit/target) decides so.
Section 4.3.b of current draft [1] states:
b. A scheduler with per-flow queues such as FQ-CoDel or FQ-PIE can
be used for L4S. For instance within each queue of an FQ-CoDel
system, as well as a CoDel AQM, there is typically also ECN
marking at an immediate (unsmoothed) shallow threshold to support
use in data centres (see Sec.5.2.7 of [RFC8290]). This can be
modified so that the shallow threshold is solely applied to
ECT(1) packets. Then if there is a flow of non-ECN or ECT(0)
packets in the per-flow-queue, the Classic AQM (e.g. CoDel) is
applied; while if there is a flow of ECT(1) packets in the queue,
the shallower (typically sub-millisecond) threshold is applied.
Tested:
tc qd replace dev eth1 root fq_codel ce_threshold_ect1 50usec
netperf ... -t TCP_STREAM -- K dctcp
tc -s -d qd sh dev eth1
qdisc fq_codel 8022: root refcnt 32 limit 10240p flows 1024 quantum 9212 target 5ms ce_threshold_ect1 49us interval 100ms memory_limit 32Mb ecn drop_batch 64
Sent
14388596616 bytes
9543449 pkt (dropped 0, overlimits 0 requeues 152013)
backlog 0b 0p requeues 152013
maxpacket 68130 drop_overlimit 0 new_flow_count 95678 ecn_mark 0 ce_mark 7639
new_flows_len 0 old_flows_len 0
[1] L4S current draft:
https://datatracker.ietf.org/doc/html/draft-ietf-tsvwg-l4s-arch
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Ingemar Johansson S <ingemar.s.johansson@ericsson.com>
Cc: Tom Henderson <tomh@tomh.org>
Cc: Bob Briscoe <in@bobbriscoe.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 14 Oct 2021 17:59:17 +0000 (10:59 -0700)]
net: add skb_get_dsfield() helper
skb_get_dsfield(skb) gets dsfield from skb, or -1
if an error was found.
This is basically a wrapper around ipv4_get_dsfield()
and ipv6_get_dsfield().
Used by following patch for fq_codel.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Ingemar Johansson S <ingemar.s.johansson@ericsson.com>
Cc: Tom Henderson <tomh@tomh.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 14 Oct 2021 13:41:26 +0000 (06:41 -0700)]
tcp: switch orphan_count to bare per-cpu counters
Use of percpu_counter structure to track count of orphaned
sockets is causing problems on modern hosts with 256 cpus
or more.
Stefan Bach reported a serious spinlock contention in real workloads,
that I was able to reproduce with a netfilter rule dropping
incoming FIN packets.
53.56% server [kernel.kallsyms] [k] queued_spin_lock_slowpath
|
---queued_spin_lock_slowpath
|
--53.51%--_raw_spin_lock_irqsave
|
--53.51%--__percpu_counter_sum
tcp_check_oom
|
|--39.03%--__tcp_close
| tcp_close
| inet_release
| inet6_release
| sock_close
| __fput
| ____fput
| task_work_run
| exit_to_usermode_loop
| do_syscall_64
| entry_SYSCALL_64_after_hwframe
| __GI___libc_close
|
--14.48%--tcp_out_of_resources
tcp_write_timeout
tcp_retransmit_timer
tcp_write_timer_handler
tcp_write_timer
call_timer_fn
expire_timers
__run_timers
run_timer_softirq
__softirqentry_text_start
As explained in commit
cf86a086a180 ("net/dst: use a smaller percpu_counter
batch for dst entries accounting"), default batch size is too big
for the default value of tcp_max_orphans (262144).
But even if we reduce batch sizes, there would still be cases
where the estimated count of orphans is beyond the limit,
and where tcp_too_many_orphans() has to call the expensive
percpu_counter_sum_positive().
One solution is to use plain per-cpu counters, and have
a timer to periodically refresh this cache.
Updating this cache every 100ms seems about right, tcp pressure
state is not radically changing over shorter periods.
percpu_counter was nice 15 years ago while hosts had less
than 16 cpus, not anymore by current standards.
v2: Fix the build issue for CONFIG_CRYPTO_DEV_CHELSIO_TLS=m,
reported by kernel test robot <lkp@intel.com>
Remove unused socket argument from tcp_too_many_orphans()
Fixes:
dd24c00191d5 ("net: Use a percpu_counter for orphan_count")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Stefan Bach <sfb@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Johnston [Thu, 14 Oct 2021 08:10:50 +0000 (16:10 +0800)]
mctp: Avoid leak of mctp_sk_key
mctp_key_alloc() returns a key already referenced.
The mctp_route_input() path receives a packet for a bind socket and
allocates a key. It passes the key to mctp_key_add() which takes a
refcount and adds the key to lists. mctp_route_input() should then
release its own refcount when setting the key pointer to NULL.
In the mctp_alloc_local_tag() path (for mctp_local_output()) we
similarly need to unref the key before returning (mctp_reserve_tag()
takes a refcount and adds the key to lists).
Fixes:
73c618456dc5 ("mctp: locking, lifetime and validity changes for sk_keys")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Oct 2021 10:06:38 +0000 (11:06 +0100)]
Merge branch 'qca8337-improvements'
Ansuel Smith says:
====================
Multiple improvement for qca8337 switch
This series is the final step of a long process of porting 80+ devices
to use the new qca8k driver instead of the hacky qca one based on never
merged swconfig platform.
Some background to justify all these additions.
QCA used a special binding to declare raw initval to set the swich. I
made a script to convert all these magic values and convert 80+ dts and
scan all the needed "unsupported regs". We find a baseline where we
manage to find the common and used regs so in theory hopefully we don't
have to add anymore things.
We discovered lots of things with this, especially about how differently
qca8327 works compared to qca8337.
In short, we found that qca8327 have some problem with suspend/resume for
their internal phy. It instead sets some dedicated regs that suspend the
phy without setting the standard bit. First 4 patch are to fix this.
There is also a patch about preferring master. This is directly from the
original driver and it seems to be needed to prevent some problem with
the pause frame.
Every ipq806x target sets the mac power sel and this specific reg
regulates the output voltage of the regulator. Without this some
instability can occur.
Some configuration (for some reason) swap mac6 with mac0. We add support
for this.
Also, we discovered that some device doesn't work at all with pll enabled
for sgmii line. In the original code this was based on the switch
revision. In later revision the pll regs were decided based on the switch
type (disabled for qca8327 and enabled for qca8337) but still some
device had that disabled in the initval regs.
Considering we found at least one qca8337 device that required pll
disabled to work (no traffic problem) we decided to introduce a binding
to enable pll and set it only with that.
Lastly, we add support for led open drain that require the power-on-sel
to set. Also, some device have only the power-on-sel set in the initval
so we add also support for that. This is needed for the correct function
of the switch leds.
Qca8327 have a special reg in the pws regs that set it to a reduced
48pin layout. This is needed or the switch doesn't work.
These are all the special configuration we find on all these devices that
are from various targets. Mostly ath79, ipq806x and bcm53xx.
Changes v7:
- Fix missing newline in yaml
- Handle error with wrong cpu port detected
- Move yaml commit as last to fix bot error
Changes v6:
- Convert Documentation to yaml
- Add extra check for cpu port and invalid phy mode
- Add co developed by tag to give credits to Matthew
Changes v5:
- Swap patch. Document first then implement.
- Fix some grammar error reported.
- Rework function. Remove phylink mac_config DT scan and move everything
to dedicated function in probe.
- Introduce new logic for delay selection where is also supported with
internal delay declared and rgmii set as phy mode
- Start working on ymal conversion. Will later post this in v6 when we
finally take final decision about mac swap.
Changes v4:
- Fix typo in SGMII falling edge about using PHY id instead of
switch id
Changes v3:
- Drop phy patches (proposed separateley)
- Drop special pwr binding. Rework to ipq806x specific
- Better describe compatible and add serial print on switch chip
- Drop mac exchange. Rework falling edge and move it to mac_config
- Add support for port 6 cpu port. Drop hardcoded cpu port to port0
- Improve port stability with sgmii. QCA source have intenal delay also
for sgmii
- Add warning with pll enabled on wrong configuration
Changes v2:
- Reword Documentation patch to dt-bindings
- Propose first 2 phy patch to net
- Better describe and add hint on how to use all the new
bindings
- Rework delay scan function and move to phylink mac_config
- Drop package48 wrong binding
- Introduce support for qca8328 switch
- Fix wrong binding name power-on-sel
- Return error on wrong config with led open drain and
ignore-power-on-sel not set
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthew Hagan [Wed, 13 Oct 2021 22:39:21 +0000 (00:39 +0200)]
dt-bindings: net: dsa: qca8k: convert to YAML schema
Convert the qca8k bindings to YAML format.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Co-developed-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Wed, 13 Oct 2021 22:39:20 +0000 (00:39 +0200)]
dt-bindings: net: ipq8064-mdio: fix warning with new qca8k switch
Fix warning now that we have qca8k switch Documentation using yaml.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Wed, 13 Oct 2021 22:39:19 +0000 (00:39 +0200)]
net: dsa: qca8k: move port config to dedicated struct
Move ports related config to dedicated struct to keep things organized.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Wed, 13 Oct 2021 22:39:18 +0000 (00:39 +0200)]
net: dsa: qca8k: set internal delay also for sgmii
QCA original code report port instability and sa that SGMII also require
to set internal delay. Generalize the rgmii delay function and apply the
advised value if they are not defined in DT.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Wed, 13 Oct 2021 22:39:17 +0000 (00:39 +0200)]
net: dsa: qca8k: add support for QCA8328
QCA8328 switch is the bigger brother of the qca8327. Same regs different
chip. Change the function to set the correct pin layout and introduce a
new match_data to differentiate the 2 switch as they have the same ID
and their internal PHY have the same ID.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Wed, 13 Oct 2021 22:39:16 +0000 (00:39 +0200)]
dt-bindings: net: dsa: qca8k: document support for qca8328
QCA8328 is the bigger brother of qca8327. Document the new compatible
binding and add some information to understand the various switch
compatible.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Wed, 13 Oct 2021 22:39:15 +0000 (00:39 +0200)]
net: dsa: qca8k: add support for pws config reg
Some qca8327 switch require to force the ignore of power on sel
strapping. Some switch require to set the led open drain mode in regs
instead of using strapping. While most of the device implements this
using the correct way using pin strapping, there are still some broken
device that require to be set using sw regs.
Introduce a new binding and support these special configuration.
As led open drain require to ignore pin strapping to work, the probe
fails with EINVAL error with incorrect configuration.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Wed, 13 Oct 2021 22:39:14 +0000 (00:39 +0200)]
dt-bindings: net: dsa: qca8k: Document qca,led-open-drain binding
Document new binding qca,ignore-power-on-sel used to ignore
power on strapping and use sw regs instead.
Document qca,led-open.drain to set led to open drain mode, the
qca,ignore-power-on-sel is mandatory with this enabled or an error will
be reported.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Wed, 13 Oct 2021 22:39:13 +0000 (00:39 +0200)]
net: dsa: qca8k: add explicit SGMII PLL enable
Support enabling PLL on the SGMII CPU port. Some device require this
special configuration or no traffic is transmitted and the switch
doesn't work at all. A dedicated binding is added to the CPU node
port to apply the correct reg on mac config.
Fail to correctly configure sgmii with qca8327 switch and warn if pll is
used on qca8337 with a revision greater than 1.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Wed, 13 Oct 2021 22:39:12 +0000 (00:39 +0200)]
dt-bindings: net: dsa: qca8k: Document qca,sgmii-enable-pll
Document qca,sgmii-enable-pll binding used in the CPU nodes to
enable SGMII PLL on MAC config.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Wed, 13 Oct 2021 22:39:11 +0000 (00:39 +0200)]
net: dsa: qca8k: rework rgmii delay logic and scan for cpu port 6
Future proof commit. This switch have 2 CPU ports and one valid
configuration is first CPU port set to sgmii and second CPU port set to
rgmii-id. The current implementation detects delay only for CPU port
zero set to rgmii and doesn't count any delay set in a secondary CPU
port. Drop the current delay scan function and move it to the sgmii
parser function to generalize and implicitly add support for secondary
CPU port set to rgmii-id. Introduce new logic where delay is enabled
also with internal delay binding declared and rgmii set as PHY mode.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Wed, 13 Oct 2021 22:39:10 +0000 (00:39 +0200)]
net: dsa: qca8k: add support for cpu port 6
Currently CPU port is always hardcoded to port 0. This switch have 2 CPU
ports. The original intention of this driver seems to be use the
mac06_exchange bit to swap MAC0 with MAC6 in the strange configuration
where device have connected only the CPU port 6. To skip the
introduction of a new binding, rework the driver to address the
secondary CPU port as primary and drop any reference of hardcoded port.
With configuration of mac06 exchange, just skip the definition of port0
and define the CPU port as a secondary. The driver will autoconfigure
the switch to use that as the primary CPU port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Wed, 13 Oct 2021 22:39:09 +0000 (00:39 +0200)]
dt-bindings: net: dsa: qca8k: Document support for CPU port 6
The switch now support CPU port to be set 6 instead of be hardcoded to
0. Document support for it and describe logic selection.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Wed, 13 Oct 2021 22:39:08 +0000 (00:39 +0200)]
net: dsa: qca8k: add support for sgmii falling edge
Add support for this in the qca8k driver. Also add support for SGMII
rx/tx clock falling edge. This is only present for pad0, pad5 and
pad6 have these bit reserved from Documentation. Add a comment that this
is hardcoded to PAD0 as qca8327/28/34/37 have an unique sgmii line and
setting falling in port0 applies to both configuration with sgmii used
for port0 or port6.
Co-developed-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Wed, 13 Oct 2021 22:39:07 +0000 (00:39 +0200)]
dt-bindings: net: dsa: qca8k: Add SGMII clock phase properties
Add names and descriptions of additional PORT0_PAD_CTRL properties.
qca,sgmii-(rx|tx)clk-falling-edge are for setting the respective clock
phase to failling edge.
Co-developed-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Wed, 13 Oct 2021 22:39:06 +0000 (00:39 +0200)]
dsa: qca8k: add mac_power_sel support
Add missing mac power sel support needed for ipq8064/5 SoC that require
1.8v for the internal regulator port instead of the default 1.5v.
If other device needs this, consider adding a dedicated binding to
support this.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Wed, 13 Oct 2021 16:51:42 +0000 (17:51 +0100)]
xen-netback: Remove redundant initialization of variable err
The variable err is being initialized with a value that is never read, it
is being updated immediately afterwards. The assignment is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Wed, 13 Oct 2021 09:19:20 +0000 (17:19 +0800)]
page_pool: disable dma mapping support for 32-bit arch with 64-bit DMA
As the 32-bit arch with 64-bit DMA seems to rare those days,
and page pool might carry a lot of code and complexity for
systems that possibly.
So disable dma mapping support for such systems, if drivers
really want to work on such systems, they have to implement
their own DMA-mapping fallback tracking outside page_pool.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 15 Oct 2021 03:01:08 +0000 (20:01 -0700)]
Merge branch 'octeontx2-af-miscellaneous-changes-for-cpt'
Srujana Challa says:
====================
octeontx2-af: Miscellaneous changes for CPT
This patchset consists of miscellaneous changes for CPT.
First patch enables the CPT HW interrupts, second patch
adds support for CPT LF teardown in non FLR path and
final patch does CPT CTX flush in FLR handler.
v2:
- Fixed a warning reported by kernel test robot.
====================
Link: https://lore.kernel.org/r/20211013055621.1812301-1-schalla@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Srujana Challa [Wed, 13 Oct 2021 05:56:21 +0000 (11:26 +0530)]
octeontx2-af: Add support to flush full CPT CTX cache
Adds support to flush or invalidate CPT CTX entries as part of FLR
and also provides a mailbox to flush CPT CTX entries in case of
graceful exit.
This patch also adds support for AF -> CPT PF uplink mailbox messages
and adds a new mbox message to submit a CPT instruction from AF.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nithin Dabilpuram [Wed, 13 Oct 2021 05:56:20 +0000 (11:26 +0530)]
octeontx2-af: Perform cpt lf teardown in non FLR path
Perform CPT LF teardown in non FLR path as well via cpt_lf_free()
Currently CPT LF teardown and reset sequence is only
done when FLR is handled with CPT LF still attached.
This patch also fixes cpt_lf_alloc() to set EXEC_LDWB in
CPT_AF_LFX_CTL2 when being completely overwritten as that is
the default value and is better for performance.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Srujana Challa [Wed, 13 Oct 2021 05:56:19 +0000 (11:26 +0530)]
octeontx2-af: Enable CPT HW interrupts
This patch enables and registers interrupt handler for CPT HW
interrupts.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Randy Dunlap [Thu, 14 Oct 2021 05:06:06 +0000 (22:06 -0700)]
net: tulip: winbond-840: fix build for UML
On i386, when builtin (not a loadable module), the winbond-840 driver
inspects boot_cpu_data to see what CPU family it is running on, and
then acts on that data. The "family" struct member (x86) does not exist
when running on UML, so prevent that test and do the default action.
Prevents this build error on UML + i386:
../drivers/net/ethernet/dec/tulip/winbond-840.c: In function ‘init_registers’:
../drivers/net/ethernet/dec/tulip/winbond-840.c:882:19: error: ‘struct cpuinfo_um’ has no member named ‘x86’
if (boot_cpu_data.x86 <= 4) {
Fixes:
68f5d3f3b654 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-um@lists.infradead.org
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Link: https://lore.kernel.org/r/20211014050606.7288-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Randy Dunlap [Thu, 14 Oct 2021 05:05:16 +0000 (22:05 -0700)]
net: intel: igc_ptp: fix build for UML
On a UML build, the igc_ptp driver uses CONFIG_X86_TSC for timestamp
conversion. The function that is used is not available on UML builds,
so have the function use the default system_counterval_t timestamp
instead for UML builds.
Prevents this build error on UML:
../drivers/net/ethernet/intel/igc/igc_ptp.c: In function ‘igc_device_tstamp_to_system’:
../drivers/net/ethernet/intel/igc/igc_ptp.c:777:9: error: implicit declaration of function ‘convert_art_ns_to_tsc’ [-Werror=implicit-function-declaration]
return convert_art_ns_to_tsc(tstamp);
../drivers/net/ethernet/intel/igc/igc_ptp.c:777:9: error: incompatible types when returning type ‘int’ but ‘struct system_counterval_t’ was expected
return convert_art_ns_to_tsc(tstamp);
Fixes:
68f5d3f3b654 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-um@lists.infradead.org
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Link: https://lore.kernel.org/r/20211014050516.6846-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Randy Dunlap [Thu, 14 Oct 2021 05:05:00 +0000 (22:05 -0700)]
net: fealnx: fix build for UML
On i386, when builtin (not a loadable module), the fealnx driver
inspects boot_cpu_data to see what CPU family it is running on, and
then acts on that data. The "family" struct member (x86) does not exist
when running on UML, so prevent that test and do the default action.
Prevents this build error on UML + i386:
../drivers/net/ethernet/fealnx.c: In function ‘netdev_open’:
../drivers/net/ethernet/fealnx.c:861:19: error: ‘struct cpuinfo_um’ has no member named ‘x86’
Fixes:
68f5d3f3b654 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-um@lists.infradead.org
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Link: https://lore.kernel.org/r/20211014050500.5620-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jiasheng Jiang [Thu, 14 Oct 2021 01:26:26 +0000 (01:26 +0000)]
hv_netvsc: Add comment of netvsc_xdp_xmit()
Adding comment to avoid the misusing of netvsc_xdp_xmit().
Otherwise the value of skb->queue_mapping could be 0 and
then the return value of skb_get_rx_queue() could be MAX_U16
cause by overflow.
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1634174786-1810351-1-git-send-email-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 15 Oct 2021 02:16:24 +0000 (19:16 -0700)]
Merge branch 'minor-managed-neighbor-follow-ups'
Daniel Borkmann says:
====================
Minor managed neighbor follow-ups
Minor follow-up series to address prior feedback from David and Jakub.
Patch 1 adds a build time assertion to prevent overflows when shifting
in extended flags, patch 2 is a cleanup to use NLA_POLICY_MASK instead
of open-coding invalid flags rejection and patch 3 rejects creating new
neighbors with NUD_PERMANENT & NTF_MANAGED. For details, see individual
patches.
====================
Link: https://lore.kernel.org/r/20211013132140.11143-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann [Wed, 13 Oct 2021 13:21:40 +0000 (15:21 +0200)]
net, neigh: Reject creating NUD_PERMANENT with NTF_MANAGED entries
The combination of NUD_PERMANENT + NTF_MANAGED is not supported and does
not make sense either given the former indicates a static/fixed neighbor
entry whereas the latter a dynamically resolved one. While it is possible
to transition from one over to the other, we should however reject such
creation attempts.
Fixes:
7482e3841d52 ("net, neigh: Add NTF_MANAGED flag for managed neighbor entries")
Suggested-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann [Wed, 13 Oct 2021 13:21:39 +0000 (15:21 +0200)]
net, neigh: Use NLA_POLICY_MASK helper for NDA_FLAGS_EXT attribute
Instead of open-coding a check for invalid bits in NTF_EXT_MASK, we can just
use the NLA_POLICY_MASK() helper instead, and simplify NDA_FLAGS_EXT sanity
check this way.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann [Wed, 13 Oct 2021 13:21:38 +0000 (15:21 +0200)]
net, neigh: Add build-time assertion to avoid neigh->flags overflow
Currently, NDA_FLAGS_EXT flags allow a maximum of 24 bits to be used for
extended neighbor flags. These are eventually fed into neigh->flags by
shifting with NTF_EXT_SHIFT as per commit
2c611ad97a82 ("net, neigh:
Extend neigh->flags to 32 bit to allow for extensions").
If really ever needed in future, the full 32 bits from NDA_FLAGS_EXT can
be used, it would only require to move neigh->flags from u32 to u64 inside
the kernel.
Add a build-time assertion such that when extending the NTF_EXT_MASK with
new bits, we'll trigger an error once we surpass the 24th bit. This assumes
that no bit holes in new NTF_EXT_* flags will slip in from UAPI, but I
think this is reasonable to assume.
Suggested-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yuval Shaia [Wed, 13 Oct 2021 06:49:21 +0000 (09:49 +0300)]
net: mvneta: Delete unused variable
The variable pp is not in use - delete it.
Signed-off-by: Yuval Shaia <yshaia@marvell.com>
Link: https://lore.kernel.org/r/20211013064921.26346-1-yshaia@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lay, Kuan Loon [Wed, 13 Oct 2021 06:59:41 +0000 (14:59 +0800)]
net: phy: dp83867: introduce critical chip default init for non-of platform
PHY driver dp83867 has rich supports for OF-platform to fine-tune the PHY
chip during phy configuration. However, for non-OF platform, certain PHY
tunable parameters such as IO impedance and RX & TX internal delays are
critical and should be initialized to its default during PHY driver probe.
Tested-by: Clement <clement@intel.com>
Signed-off-by: Lay, Kuan Loon <kuan.loon.lay@intel.com>
Co-developed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20211013065941.2124858-1-boon.leong.ong@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yuiko Oshino [Tue, 12 Oct 2021 13:49:53 +0000 (09:49 -0400)]
net: microchip: lan743x: add support for PTP pulse width (duty cycle)
If the PTP_PEROUT_DUTY_CYCLE flag is set, then check if the
request_on value in ptp_perout_request matches the pre-defined
values or a toggle option.
Return a failure if the value is not supported.
Preserve the old behaviors if the PTP_PEROUT_DUTY_CYCLE flag is not
set.
Tested with an oscilloscope on EVB-LAN7430:
e.g., to output PPS 1sec period 500mS on (high) to GPIO 2.
./testptp -L 2,2
./testptp -p
1000000000 -w
500000000
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Link: https://lore.kernel.org/r/1634046593-64312-1-git-send-email-yuiko.oshino@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthias Schiffer [Tue, 12 Oct 2021 10:34:02 +0000 (12:34 +0200)]
net: phy: micrel: make *-skew-ps check more lenient
It seems reasonable to fine-tune only some of the skew values when using
one of the rgmii-*id PHY modes, and even when all skew values are
specified, using the correct ID PHY mode makes sense for documentation
purposes. Such a configuration also appears in the binding docs in
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt, so the driver
should not warn about it.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211012103402.21438-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 14 Oct 2021 23:50:14 +0000 (16:50 -0700)]
Merge git://git./linux/kernel/git/netdev/net
tools/testing/selftests/net/ioam6.sh
7b1700e009cc ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a56 ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arnd Bergmann [Thu, 14 Oct 2021 09:00:37 +0000 (11:00 +0200)]
net: of: fix stub of_net helpers for CONFIG_NET=n
Moving the of_net code from drivers/of/ to net/core means we
no longer stub out the helpers when networking is disabled,
which leads to a randconfig build failure with at least one
ARM platform that calls this from non-networking code:
arm-linux-gnueabi-ld: arch/arm/mach-mvebu/kirkwood.o: in function `kirkwood_dt_eth_fixup':
kirkwood.c:(.init.text+0x54): undefined reference to `of_get_mac_address'
Restore the way this worked before by changing that #ifdef
check back to testing for both CONFIG_OF and CONFIG_NET.
Fixes:
e330fb14590c ("of: net: move of_net under net/")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211014090055.2058949-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 14 Oct 2021 22:21:39 +0000 (18:21 -0400)]
Merge tag 'net-5.15-rc6' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Quite calm.
The noisy DSA driver (embedded switches) changes, and adjustment to
IPv6 IOAM behavior add to diffstat's bottom line but are not scary.
Current release - regressions:
- af_unix: rename UNIX-DGRAM to UNIX to maintain backwards
compatibility
- procfs: revert "add seq_puts() statement for dev_mcast", minor
format change broke user space
Current release - new code bugs:
- dsa: fix bridge_num not getting cleared after ports leaving the
bridge, resource leak
- dsa: tag_dsa: send packets with TX fwd offload from VLAN-unaware
bridges using VID 0, prevent packet drops if pvid is removed
- dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unaware, prevent HW
getting confused about station to VLAN mapping
Previous releases - regressions:
- virtio-net: fix for skb_over_panic inside big mode
- phy: do not shutdown PHYs in READY state
- dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's, fix link
LED staying lit after ifdown
- mptcp: fix possible infinite wait on recvmsg(MSG_WAITALL)
- mqprio: Correct stats in mqprio_dump_class_stats()
- ice: fix deadlock for Tx timestamp tracking flush
- stmmac: fix feature detection on old hardware
Previous releases - always broken:
- sctp: account stream padding length for reconf chunk
- icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe()
- isdn: cpai: check ctr->cnr to avoid array index out of bound
- isdn: mISDN: fix sleeping function called from invalid context
- nfc: nci: fix potential UAF of rf_conn_info object
- dsa: microchip: prevent ksz_mib_read_work from kicking back in
after it's canceled in .remove and crashing
- dsa: mv88e6xxx: isolate the ATU databases of standalone and bridged
ports
- dsa: sja1105, ocelot: break circular dependency between switch and
tag drivers
- dsa: felix: improve timestamping in presence of packe loss
- mlxsw: thermal: fix out-of-bounds memory accesses
Misc:
- ipv6: ioam: move the check for undefined bits to improve
interoperability"
* tag 'net-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (60 commits)
icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe
MAINTAINERS: Update the devicetree documentation path of imx fec driver
sctp: account stream padding length for reconf chunk
mlxsw: thermal: Fix out-of-bounds memory accesses
ethernet: s2io: fix setting mac address during resume
NFC: digital: fix possible memory leak in digital_in_send_sdd_req()
NFC: digital: fix possible memory leak in digital_tg_listen_mdaa()
nfc: fix error handling of nfc_proto_register()
Revert "net: procfs: add seq_puts() statement for dev_mcast"
net: encx24j600: check error in devm_regmap_init_encx24j600
net: korina: select CRC32
net: arc: select CRC32
net: dsa: felix: break at first CPU port during init and teardown
net: dsa: tag_ocelot_8021q: fix inability to inject STP BPDUs into BLOCKING ports
net: dsa: felix: purge skb from TX timestamping queue if it cannot be sent
net: dsa: tag_ocelot_8021q: break circular dependency with ocelot switch lib
net: dsa: tag_ocelot: break circular dependency with ocelot switch lib driver
net: mscc: ocelot: cross-check the sequence id from the timestamp FIFO with the skb PTP header
net: mscc: ocelot: deny TX timestamping of non-PTP packets
net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skb
...
Jakub Kicinski [Wed, 13 Oct 2021 20:54:50 +0000 (13:54 -0700)]
ethernet: remove random_ether_addr()
random_ether_addr() was the original name of the helper which
was kept for backward compatibility (?) after the rename in
commit
0a4dd594982a ("etherdevice: Rename random_ether_addr
to eth_random_addr").
We have a single random_ether_addr() caller left in tree
while there are 70 callers of eth_random_addr().
Time to drop this define.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20211013205450.328092-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 14 Oct 2021 16:22:32 +0000 (09:22 -0700)]
Merge branch 'ethernet-more-netdev-dev_addr-write-removals'
Jakub Kicinski says:
====================
ethernet: more netdev->dev_addr write removals
Another series removing direct writes to netdev->dev_addr.
====================
Link: https://lore.kernel.org/r/20211013204435.322561-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 13 Oct 2021 20:44:35 +0000 (13:44 -0700)]
ethernet: replace netdev->dev_addr 16bit writes
Commit
406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
This patch takes care of drivers which cast netdev->dev_addr to
a 16bit type, often with an explicit byte order.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 13 Oct 2021 20:44:34 +0000 (13:44 -0700)]
ethernet: replace netdev->dev_addr assignment loops
A handful of drivers contains loops assigning the mac
addr byte by byte. Convert those to eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 13 Oct 2021 20:44:33 +0000 (13:44 -0700)]
ethernet: ibm/emac: use of_get_ethdev_address() to load dev_addr
A straggler I somehow missed in the automated conversion in
commit
9ca01b25dfff ("ethernet: use of_get_ethdev_address()").
Use the new helper instead of using netdev->dev_addr directly.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 13 Oct 2021 20:44:32 +0000 (13:44 -0700)]
ethernet: manually convert memcpy(dev_addr,..., sizeof(addr))
A handful of drivers use sizeof(addr) for the size of
the address, after manually confirming the size is
indeed 6 convert them to eth_hw_addr_set().
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petko Manolov <petkan@nucleusys.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 13 Oct 2021 20:44:31 +0000 (13:44 -0700)]
ethernet: make use of eth_hw_addr_random() where appropriate
Number of drivers use eth_random_addr(netdev->dev_addr)
thus writing to netdev->dev_addr directly, and not setting
the address type. Switch them to eth_hw_addr_random().
@@
expression netdev;
@@
- eth_random_addr(netdev->dev_addr);
+ eth_hw_addr_random(netdev);
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 13 Oct 2021 20:44:30 +0000 (13:44 -0700)]
ethernet: make eth_hw_addr_random() use dev_addr_set()
Commit
406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 14 Oct 2021 14:24:31 +0000 (07:24 -0700)]
ethernet: constify references to netdev->dev_addr in drivers
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit
406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 14 Oct 2021 16:03:33 +0000 (09:03 -0700)]
Merge branch '100GbE' of git://git./linux/kernel/git/tnguy/next-queue
Maciej Machnikowski says:
====================
100GbE Intel Wired LAN Driver Updates 2021-10-14
Extend the driver implementation to support PTP pins on E810-T
and derivative devices.
E810-T adapters are equipped with:
- 2 external bidirectional SMA connectors
- 1 internal TX U.FL shared with SMA1
- 1 internal RX U.FL shared with SMA2
The SMA and U.FL configuration is controlled by the external
multiplexer.
E810-T Derivatives are equipped with:
- 2 1PPS outputs on SDP20 and SDP22
- 2 1PPS inputs on SDP21 and SDP23
====================
Link: https://lore.kernel.org/r/20211014153531.2908804-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Thu, 14 Oct 2021 09:50:50 +0000 (05:50 -0400)]
icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe
In icmp_build_probe(), the icmp_ext_echo_iio parsing should be done
step by step and skb_header_pointer() return value should always be
checked, this patch fixes 3 places in there:
- On case ICMP_EXT_ECHO_CTYPE_NAME, it should only copy ident.name
from skb by skb_header_pointer(), its len is ident_len. Besides,
the return value of skb_header_pointer() should always be checked.
- On case ICMP_EXT_ECHO_CTYPE_INDEX, move ident_len check ahead of
skb_header_pointer(), and also do the return value check for
skb_header_pointer().
- On case ICMP_EXT_ECHO_CTYPE_ADDR, before accessing iio->ident.addr.
ctype3_hdr.addrlen, skb_header_pointer() should be called first,
then check its return value and ident_len.
On subcases ICMP_AFI_IP and ICMP_AFI_IP6, also do check for ident.
addr.ctype3_hdr.addrlen and skb_header_pointer()'s return value.
On subcase ICMP_AFI_IP, the len for skb_header_pointer() should be
"sizeof(iio->extobj_hdr) + sizeof(iio->ident.addr.ctype3_hdr) +
sizeof(struct in_addr)" or "ident_len".
v1->v2:
- To make it more clear, call skb_header_pointer() once only for
iio->indent's parsing as Jakub Suggested.
v2->v3:
- The extobj_hdr.length check against sizeof(_iio) should be done
before calling skb_header_pointer(), as Eric noticed.
Fixes:
d329ea5bd884 ("icmp: add response to RFC 8335 PROBE messages")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/31628dd76657ea62f5cf78bb55da6b35240831f1.1634205050.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Maciej Machnikowski [Tue, 17 Aug 2021 11:09:18 +0000 (13:09 +0200)]
ice: Implement support for SMA and U.FL on E810-T
Expose SMA and U.FL connectors as ptp_pins on E810-T based adapters and
allow controlling them.
E810-T adapters are equipped with:
- 2 external bidirectional SMA connectors
- 1 internal TX U.FL
- 1 internal RX U.FL
U.FL connectors share signal lines with the SMA connectors. The TX U.FL1
share the line with the SMA1 and the RX U.FL2 share line with the SMA2.
This dependence is controlled by the ice_verify_pin_e810t.
Additionally add support for the E810-T-based devices which don't use the
SMA/U.FL controller. If the IO expander is not detected don't expose pins
and use 2 predefined 1PPS input and output pins.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Maciej Machnikowski [Tue, 17 Aug 2021 11:09:17 +0000 (13:09 +0200)]
ice: Add support for SMA control multiplexer
E810-T adapters have two external bidirectional SMA connectors and two
internal unidirectional U.FL connectors. Multiplexing between U.FL and
SMA and SMA direction is controlled using the PCA9575 expander.
Add support for the PCA9575 detection and control of the respective pins
of the SMA/U.FL multiplexer using the GPIO AQ API.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Maciej Machnikowski [Tue, 17 Aug 2021 11:09:16 +0000 (13:09 +0200)]
ice: Implement functions for reading and setting GPIO pins
Implement ice_aq_get_gpio and ice_aq_set_gpio for reading and changing
the state of GPIO pins described in the topology.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Maciej Machnikowski [Mon, 30 Aug 2021 12:26:14 +0000 (14:26 +0200)]
ice: Refactor ice_aqc_link_topo_addr
Separate link topo parameters in struct ice_aqc_link_topo_addr into
new struct ice_aqc_link_topo_params.
This keeps input parameters for the get_link_topo command in a separate
structure and is required by future commands that operate only on link
topo params without the node handle.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Cai Huoqing [Thu, 14 Oct 2021 11:02:14 +0000 (19:02 +0800)]
MAINTAINERS: Update the devicetree documentation path of imx fec driver
Change the devicetree documentation path
to "Documentation/devicetree/bindings/net/fsl,fec.yaml"
since 'fsl-fec.txt' has been converted to 'fsl,fec.yaml' already.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211014110214.3254-1-caihuoqing@baidu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eiichi Tsukata [Wed, 13 Oct 2021 20:27:29 +0000 (17:27 -0300)]
sctp: account stream padding length for reconf chunk
sctp_make_strreset_req() makes repeated calls to sctp_addto_chunk()
which will automatically account for padding on each call. inreq and
outreq are already 4 bytes aligned, but the payload is not and doing
SCTP_PAD4(a + b) (which _sctp_make_chunk() did implicitly here) is
different from SCTP_PAD4(a) + SCTP_PAD4(b) and not enough. It led to
possible attempt to use more buffer than it was allocated and triggered
a BUG_ON.
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Fixes:
cc16f00f6529 ("sctp: add support for generating stream reconf ssn reset request chunk")
Reported-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Signed-off-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/b97c1f8b0c7ff79ac4ed206fc2c49d3612e0850c.1634156849.git.mleitner@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel [Tue, 12 Oct 2021 17:49:55 +0000 (20:49 +0300)]
mlxsw: thermal: Fix out-of-bounds memory accesses
Currently, mlxsw allows cooling states to be set above the maximum
cooling state supported by the driver:
# cat /sys/class/thermal/thermal_zone2/cdev0/type
mlxsw_fan
# cat /sys/class/thermal/thermal_zone2/cdev0/max_state
10
# echo 18 > /sys/class/thermal/thermal_zone2/cdev0/cur_state
# echo $?
0
This results in out-of-bounds memory accesses when thermal state
transition statistics are enabled (CONFIG_THERMAL_STATISTICS=y), as the
transition table is accessed with a too large index (state) [1].
According to the thermal maintainer, it is the responsibility of the
driver to reject such operations [2].
Therefore, return an error when the state to be set exceeds the maximum
cooling state supported by the driver.
To avoid dead code, as suggested by the thermal maintainer [3],
partially revert commit
a421ce088ac8 ("mlxsw: core: Extend cooling
device with cooling levels") that tried to interpret these invalid
cooling states (above the maximum) in a special way. The cooling levels
array is not removed in order to prevent the fans going below 20% PWM,
which would cause them to get stuck at 0% PWM.
[1]
BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x271/0x290
Read of size 4 at addr
ffff8881052f7bf8 by task kworker/0:0/5
CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted
5.15.0-rc3-custom-45935-gce1adf704b14 #122
Hardware name: Mellanox Technologies Ltd. "MSN2410-CB2FO"/"SA000874", BIOS 4.6.5 03/08/2016
Workqueue: events_freezable_power_ thermal_zone_device_check
Call Trace:
dump_stack_lvl+0x8b/0xb3
print_address_description.constprop.0+0x1f/0x140
kasan_report.cold+0x7f/0x11b
thermal_cooling_device_stats_update+0x271/0x290
__thermal_cdev_update+0x15e/0x4e0
thermal_cdev_update+0x9f/0xe0
step_wise_throttle+0x770/0xee0
thermal_zone_device_update+0x3f6/0xdf0
process_one_work+0xa42/0x1770
worker_thread+0x62f/0x13e0
kthread+0x3ee/0x4e0
ret_from_fork+0x1f/0x30
Allocated by task 1:
kasan_save_stack+0x1b/0x40
__kasan_kmalloc+0x7c/0x90
thermal_cooling_device_setup_sysfs+0x153/0x2c0
__thermal_cooling_device_register.part.0+0x25b/0x9c0
thermal_cooling_device_register+0xb3/0x100
mlxsw_thermal_init+0x5c5/0x7e0
__mlxsw_core_bus_device_register+0xcb3/0x19c0
mlxsw_core_bus_device_register+0x56/0xb0
mlxsw_pci_probe+0x54f/0x710
local_pci_probe+0xc6/0x170
pci_device_probe+0x2b2/0x4d0
really_probe+0x293/0xd10
__driver_probe_device+0x2af/0x440
driver_probe_device+0x51/0x1e0
__driver_attach+0x21b/0x530
bus_for_each_dev+0x14c/0x1d0
bus_add_driver+0x3ac/0x650
driver_register+0x241/0x3d0
mlxsw_sp_module_init+0xa2/0x174
do_one_initcall+0xee/0x5f0
kernel_init_freeable+0x45a/0x4de
kernel_init+0x1f/0x210
ret_from_fork+0x1f/0x30
The buggy address belongs to the object at
ffff8881052f7800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 1016 bytes inside of
1024-byte region [
ffff8881052f7800,
ffff8881052f7c00)
The buggy address belongs to the page:
page:
0000000052355272 refcount:1 mapcount:0 mapping:
0000000000000000 index:0x0 pfn:0x1052f0
head:
0000000052355272 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x200000000010200(slab|head|node=0|zone=2)
raw:
0200000000010200 ffffea0005034800 0000000300000003 ffff888100041dc0
raw:
0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881052f7a80: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc
ffff8881052f7b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>
ffff8881052f7b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff8881052f7c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881052f7c80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[2] https://lore.kernel.org/linux-pm/
9aca37cb-1629-5c67-1895-
1fdc45c0244e@linaro.org/
[3] https://lore.kernel.org/linux-pm/
af9857f2-578e-de3a-e62b-
6baff7e69fd4@linaro.org/
CC: Daniel Lezcano <daniel.lezcano@linaro.org>
Fixes:
a50c1e35650b ("mlxsw: core: Implement thermal zone")
Fixes:
a421ce088ac8 ("mlxsw: core: Extend cooling device with cooling levels")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20211012174955.472928-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arnd Bergmann [Wed, 13 Oct 2021 14:35:49 +0000 (16:35 +0200)]
ethernet: s2io: fix setting mac address during resume
After recent cleanups, gcc started warning about a suspicious
memcpy() call during the s2io_io_resume() function:
In function '__dev_addr_set',
inlined from 'eth_hw_addr_set' at include/linux/etherdevice.h:318:2,
inlined from 's2io_set_mac_addr' at drivers/net/ethernet/neterion/s2io.c:5205:2,
inlined from 's2io_io_resume' at drivers/net/ethernet/neterion/s2io.c:8569:7:
arch/x86/include/asm/string_32.h:182:25: error: '__builtin_memcpy' accessing 6 bytes at offsets 0 and 2 overlaps 4 bytes at offset 2 [-Werror=restrict]
182 | #define memcpy(t, f, n) __builtin_memcpy(t, f, n)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/netdevice.h:4648:9: note: in expansion of macro 'memcpy'
4648 | memcpy(dev->dev_addr, addr, len);
| ^~~~~~
What apparently happened is that an old cleanup changed the calling
conventions for s2io_set_mac_addr() from taking an ethernet address
as a character array to taking a struct sockaddr, but one of the
callers was not changed at the same time.
Change it to instead call the low-level do_s2io_prog_unicast() function
that still takes the old argument type.
Fixes:
2fd376884558 ("S2io: Added support set_mac_address driver entry point")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211013143613.2049096-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dinh Nguyen [Wed, 13 Oct 2021 03:40:56 +0000 (22:40 -0500)]
MAINTAINERS: Update entry for the Stratix10 firmware
Richard Gong is no longer at Intel, so update the MAINTAINER's entry for
the Stratix10 firmware drivers.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 14 Oct 2021 13:53:36 +0000 (09:53 -0400)]
Merge tag 'sound-5.15-rc6' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains quite a few device-specific fixes for usual HD- and
USB-audio in addition to a couple of ALSA core fixes (a UAF fix in
sequencer and a fix for a misplaced PCM 32bit compat ioctl).
Nothing really stands out"
* tag 'sound-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Add quirk for VF0770
ALSA: hda: avoid write to STATESTS if controller is in reset
ALSA: hda/realtek: Fix the mic type detection issue for ASUS G551JW
ALSA: pcm: Workaround for a wrong offset in SYNC_PTR compat ioctl
ALSA: hda/realtek: Fix for quirk to enable speaker output on the Lenovo 13s Gen2
ALSA: hda: intel: Allow repeatedly probing on codec configuration errors
ALSA: hda/realtek: Add quirk for TongFang PHxTxX1
ALSA: hda/realtek - ALC236 headset MIC recording issue
ALSA: usb-audio: Enable rate validation for Scarlett devices
ALSA: hda/realtek: Add quirk for Clevo X170KM-G
ALSA: hda/realtek: Complete partial device name to avoid ambiguity
ALSA: hda - Enable headphone mic on Dell Latitude laptops with ALC3254
ALSA: seq: Fix a potential UAF by wrong private_free call order
ALSA: hda/realtek: Enable 4-speaker output for Dell Precision 5560 laptop
ALSA: usb-audio: Fix a missing error check in scarlett gen2 mixer
Chen Wandun [Wed, 13 Oct 2021 09:47:02 +0000 (17:47 +0800)]
net: delete redundant function declaration
The implement of function netdev_all_upper_get_next_dev_rcu has been
removed in:
commit
f1170fd462c6 ("net: Remove all_adj_list and its references")
so delete redundant declaration in header file.
Fixes:
f1170fd462c6 ("net: Remove all_adj_list and its references")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Link: https://lore.kernel.org/r/20211013094702.3931071-1-chenwandun@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 14 Oct 2021 00:47:20 +0000 (17:47 -0700)]
Merge branch 'mlxsw-show-per-band-ecn-marked-counter-on-qdisc'
Ido Schimmel says:
====================
mlxsw: Show per-band ECN-marked counter on qdisc
The RED qdisc can expose number of packets that it has marked through
the prob_marked counter (shown in iproute2 as "marked"). This counter
currently just shows number of packets marked in the SW datapath, which
in a switch deployment likely means zero.
Spectrum-3 does support per-TC counters, and in this patchset, mlxsw
supports this RED statistic properly.
====================
Link: https://lore.kernel.org/r/20211013103748.492531-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata [Wed, 13 Oct 2021 10:37:48 +0000 (13:37 +0300)]
selftests: mlxsw: RED: Test per-TC ECN counters
Add a variant of ECN test that uses qdisc marked counter (supported on
Spectrum-3 and above) instead of the aggregate ethtool ecn_marked counter.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata [Wed, 13 Oct 2021 10:37:47 +0000 (13:37 +0300)]
mlxsw: spectrum_qdisc: Introduce per-TC ECN counters
The Qdisc code in mlxsw used to report a number of packets ECN-marked on a
port. Because reporting a per-port value as a per-TC value was misleading,
this was removed in commit
8a29581eb001 ("mlxsw: spectrum: Move the
ECN-marked packet counter to ethtool").
On Spectrum-3, a per-TC number of ECN-marked packets is available in per-TC
congestion counter group. Add a new array for the ECN counter, fetch the
values from the per-TC congestion group, and pick the value indicated by
tclass_num as appropriate.
On Spectrum-1 and Spectrum-2, this per-TC value is not available, and
zeroes will be reported, as they currently are.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata [Wed, 13 Oct 2021 10:37:46 +0000 (13:37 +0300)]
mlxsw: reg: Add ecn_marked_tc to Per-TC Congestion Counters
The PPCNT register retrieves per port performance counters. The
ecn_marked_tc field in per-TC Congestion counter group contains a count of
packets marked as ECN or potentially marked as ECN.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata [Wed, 13 Oct 2021 10:37:45 +0000 (13:37 +0300)]
mlxsw: reg: Rename MLXSW_REG_PPCNT_TC_CONG_TC to _CNT
The name does not make sense as it is. Clearly there is a typo and the
suffix should have been _CNT, like the other enumerators. Fix accordingly.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata [Wed, 13 Oct 2021 10:37:44 +0000 (13:37 +0300)]
mlxsw: reg: Fix a typo in a group heading
There is no such thing as "traffic group". The group that this is a heading
of is "per traffic class counters". Fix the heading.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 14 Oct 2021 00:44:32 +0000 (17:44 -0700)]
Merge branch 'fix-two-possible-memory-leak-problems-in-nfc-digital-module'
Ziyang Xuan says:
====================
Fix two possible memory leak problems in NFC digital module.
====================
Link: https://lore.kernel.org/r/cover.1634111083.git.william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ziyang Xuan [Wed, 13 Oct 2021 07:50:32 +0000 (15:50 +0800)]
NFC: digital: fix possible memory leak in digital_in_send_sdd_req()
'skb' is allocated in digital_in_send_sdd_req(), but not free when
digital_in_send_cmd() failed, which will cause memory leak. Fix it
by freeing 'skb' if digital_in_send_cmd() return failed.
Fixes:
2c66daecc409 ("NFC Digital: Add NFC-A technology support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ziyang Xuan [Wed, 13 Oct 2021 07:50:12 +0000 (15:50 +0800)]
NFC: digital: fix possible memory leak in digital_tg_listen_mdaa()
'params' is allocated in digital_tg_listen_mdaa(), but not free when
digital_send_cmd() failed, which will cause memory leak. Fix it by
freeing 'params' if digital_send_cmd() return failed.
Fixes:
1c7a4c24fbfd ("NFC Digital: Add target NFC-DEP support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ziyang Xuan [Wed, 13 Oct 2021 03:49:32 +0000 (11:49 +0800)]
nfc: fix error handling of nfc_proto_register()
When nfc proto id is using, nfc_proto_register() return -EBUSY error
code, but forgot to unregister proto. Fix it by adding proto_unregister()
in the error handling case.
Fixes:
c7fe3b52c128 ("NFC: add NFC socket family")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211013034932.2833737-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Wed, 13 Oct 2021 00:19:09 +0000 (03:19 +0300)]
Revert "net: procfs: add seq_puts() statement for dev_mcast"
This reverts commit
ec18e8455484370d633a718c6456ddbf6eceef21.
It turns out that there are user space programs which got broken by that
change. One example is the "ifstat" program shipped by Debian:
https://packages.debian.org/source/bullseye/ifstat
which, confusingly enough, seems to not have anything in common with the
much more familiar (at least to me) ifstat program from iproute2:
https://git.kernel.org/pub/scm/network/iproute2/iproute2.git/tree/misc/ifstat.c
root@debian:~# ifstat
ifstat: /proc/net/dev: unsupported format.
This change modified the header (first two lines of text) in
/proc/net/dev so that it looks like this:
root@debian:~# cat /proc/net/dev
Interface| Receive | Transmit
| bytes packets errs drop fifo frame compressed multicast| bytes packets errs drop fifo colls carrier compressed
lo: 97400 1204 0 0 0 0 0 0 97400 1204 0 0 0 0 0 0
bond0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sit0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eno2:
5002206 6651 0 0 0 0 0 0
105518642 1465023 0 0 0 0 0 0
swp0: 134531 2448 0 0 0 0 0 0
99599598 1464381 0 0 0 0 0 0
swp1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
swp2:
4867675 4203 0 0 0 0 0 0 58134 631 0 0 0 0 0 0
sw0p0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw0p1: 124739 2448 0 1422 0 0 0 0
93741184 1464369 0 0 0 0 0 0
sw0p2: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw2p0:
4850863 4203 0 0 0 0 0 0 54722 619 0 0 0 0 0 0
sw2p1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw2p2: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw2p3: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
br0: 10508 212 0 212 0 0 0 212
61369558 958857 0 0 0 0 0 0
whereas before it looked like this:
root@debian:~# cat /proc/net/dev
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 13160 164 0 0 0 0 0 0 13160 164 0 0 0 0 0 0
bond0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sit0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eno2: 30824 268 0 0 0 0 0 0 3332 37 0 0 0 0 0 0
swp0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
swp1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
swp2: 30824 268 0 0 0 0 0 0 2428 27 0 0 0 0 0 0
sw0p0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw0p1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw0p2: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw2p0: 29752 268 0 0 0 0 0 0 1564 17 0 0 0 0 0 0
sw2p1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw2p2: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw2p3: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
The reason why the ifstat shipped by Debian (v1.1, with a Debian patch
upgrading it to 1.1-8.1 at the time of writing) is broken is because its
"proc" driver/backend parses the header very literally:
main/drivers.c#L825
if (!data->checked && strncmp(buf, "Inter-|", 7))
goto badproc;
and there's no way in which the header can be changed such that programs
parsing like that would not get broken.
Even if we fix this ancient and very "lightly" maintained program to
parse the text output of /proc/net/dev in a more sensible way, this
story seems bound to repeat again with other programs, and modifying
them all could cause more trouble than it's worth. On the other hand,
the reverted patch had no other reason than an aesthetic one, so
reverting it is the simplest way out.
I don't know what other distributions would be affected; the fact that
Debian doesn't ship the iproute2 version of the program (a different
code base altogether, which uses netlink and not /proc/net/dev) is
surprising in itself.
Fixes:
ec18e8455484 ("net: procfs: add seq_puts() statement for dev_mcast")
Link: https://lore.kernel.org/netdev/20211009163511.vayjvtn3rrteglsu@skbuf/
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211013001909.3164185-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dan Carpenter [Wed, 13 Oct 2021 08:04:56 +0000 (11:04 +0300)]
net: enetc: fix check for allocation failure
This was supposed to be a check for if dma_alloc_coherent() failed
but it has a copy and paste bug so it will not work.
Fixes:
fb8629e2cbfc ("net: enetc: add support for software TSO")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20211013080456.GC6010@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nanyong Sun [Tue, 12 Oct 2021 12:59:01 +0000 (20:59 +0800)]
net: encx24j600: check error in devm_regmap_init_encx24j600
devm_regmap_init may return error which caused by like out of memory,
this will results in null pointer dereference later when reading
or writing register:
general protection fault in encx24j600_spi_probe
KASAN: null-ptr-deref in range [0x0000000000000090-0x0000000000000097]
CPU: 0 PID: 286 Comm: spi-encx24j600- Not tainted
5.15.0-rc2-00142-g9978db750e31-dirty #11
9c53a778c1306b1b02359f3c2bbedc0222cba652
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: 0010:regcache_cache_bypass drivers/base/regmap/regcache.c:540
Code: 54 41 89 f4 55 53 48 89 fb 48 83 ec 08 e8 26 94 a8 fe 48 8d bb a0 00 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 4a 03 00 00 4c 8d ab b0 00 00 00 48 8b ab a0 00
RSP: 0018:
ffffc900010476b8 EFLAGS:
00010207
RAX:
dffffc0000000000 RBX:
fffffffffffffff4 RCX:
0000000000000000
RDX:
0000000000000012 RSI:
ffff888002de0000 RDI:
0000000000000094
RBP:
ffff888013c9a000 R08:
0000000000000000 R09:
fffffbfff3f9cc6a
R10:
ffffc900010476e8 R11:
fffffbfff3f9cc69 R12:
0000000000000001
R13:
000000000000000a R14:
ffff888013c9af54 R15:
ffff888013c9ad08
FS:
00007ffa984ab580(0000) GS:
ffff88801fe00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
000055a6384136c8 CR3:
000000003bbe6003 CR4:
0000000000770ef0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
PKRU:
55555554
Call Trace:
encx24j600_spi_probe drivers/net/ethernet/microchip/encx24j600.c:459
spi_probe drivers/spi/spi.c:397
really_probe drivers/base/dd.c:517
__driver_probe_device drivers/base/dd.c:751
driver_probe_device drivers/base/dd.c:782
__device_attach_driver drivers/base/dd.c:899
bus_for_each_drv drivers/base/bus.c:427
__device_attach drivers/base/dd.c:971
bus_probe_device drivers/base/bus.c:487
device_add drivers/base/core.c:3364
__spi_add_device drivers/spi/spi.c:599
spi_add_device drivers/spi/spi.c:641
spi_new_device drivers/spi/spi.c:717
new_device_store+0x18c/0x1f1 [spi_stub
4e02719357f1ff33f5a43d00630982840568e85e]
dev_attr_store drivers/base/core.c:2074
sysfs_kf_write fs/sysfs/file.c:139
kernfs_fop_write_iter fs/kernfs/file.c:300
new_sync_write fs/read_write.c:508 (discriminator 4)
vfs_write fs/read_write.c:594
ksys_write fs/read_write.c:648
do_syscall_64 arch/x86/entry/common.c:50
entry_SYSCALL_64_after_hwframe arch/x86/entry/entry_64.S:113
Add error check in devm_regmap_init_encx24j600 to avoid this situation.
Fixes:
04fbfce7a222 ("net: Microchip encx24j600 driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Nanyong Sun <sunnanyong@huawei.com>
Link: https://lore.kernel.org/r/20211012125901.3623144-1-sunnanyong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 13 Oct 2021 20:39:54 +0000 (13:39 -0700)]
Merge tag 'mlx5-fixes-2021-10-12' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2021-10-12
* tag 'mlx5-fixes-2021-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Fix division by 0 in mlx5e_select_queue for representors
net/mlx5e: Mutually exclude RX-FCS and RX-port-timestamp
net/mlx5e: Switchdev representors are not vlan challenged
net/mlx5e: Fix memory leak in mlx5_core_destroy_cq() error path
net/mlx5e: Allow only complete TXQs partition in MQPRIO channel mode
net/mlx5: Fix cleanup of bridge delayed work
====================
Link: https://lore.kernel.org/r/20211012205323.20123-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Tue, 12 Oct 2021 12:37:35 +0000 (15:37 +0300)]
net: dsa: unregister cross-chip notifier after ds->ops->teardown
To be symmetric with the error unwind path of dsa_switch_setup(), call
dsa_switch_unregister_notifier() after ds->ops->teardown.
The implication is that ds->ops->teardown cannot emit cross-chip
notifiers. For example, currently the dsa_tag_8021q_unregister() call
from sja1105_teardown() does not propagate to the entire tree due to
this reason. However I cannot find an actual issue caused by this,
observed using code inspection.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211012123735.2545742-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vegard Nossum [Tue, 12 Oct 2021 15:25:09 +0000 (17:25 +0200)]
net: korina: select CRC32
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/ethernet/korina.o: in function `korina_multicast_list':
korina.c:(.text+0x1af): undefined reference to `crc32_le'
Fixes:
ef11291bcd5f9 ("Add support the Korina (IDT RC32434) Ethernet MAC")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Florian fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211012152509.21771-1-vegard.nossum@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Anders Roxell [Wed, 13 Oct 2021 13:57:43 +0000 (15:57 +0200)]
marvell: octeontx2: build error: unknown type name 'u64'
Building an allmodconfig kernel arm64 kernel, the following build error
shows up:
In file included from drivers/crypto/marvell/octeontx2/cn10k_cpt.c:4:
include/linux/soc/marvell/octeontx2/asm.h:38:15: error: unknown type name 'u64'
38 | static inline u64 otx2_atomic64_fetch_add(u64 incr, u64 *ptr)
| ^~~
Include linux/types.h in asm.h so the compiler knows what the type
'u64' are.
Fixes:
af3826db74d1 ("octeontx2-pf: Use hardware register for CQE count")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Link: https://lore.kernel.org/r/20211013135743.3826594-1-anders.roxell@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 12 Oct 2021 14:27:57 +0000 (07:27 -0700)]
net: remove single-byte netdev->dev_addr writes
Make the drivers which use single-byte netdev addresses
(netdev->addr_len == 1) use the appropriate address setting
helpers.
arcnet copies from int variables and io reads a lot, so
add a helper for arcnet drivers to use.
Similar helper could be reused for phonet and appletalk
but there isn't any good central location where we could
put it, and netdevice.h is already very crowded.
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for HSI
Link: https://lore.kernel.org/r/20211012142757.4124842-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 13 Oct 2021 16:41:39 +0000 (09:41 -0700)]
Merge branch 'net-use-dev_addr_set-in-hamradio-and-ip-tunnels'
Jakub Kicinski says:
====================
net: use dev_addr_set() in hamradio and ip tunnels
Commit
406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
====================
Link: https://lore.kernel.org/r/20211012160634.4152690-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 12 Oct 2021 16:06:34 +0000 (09:06 -0700)]
ip: use dev_addr_set() in tunnels
Use dev_addr_set() instead of writing to netdev->dev_addr
directly in ip tunnels drivers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 12 Oct 2021 16:06:33 +0000 (09:06 -0700)]
hamradio: use dev_addr_set() for setting device address
Use dev_addr_set() instead of writing to netdev->dev_addr
directly in hamradio drivers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 12 Oct 2021 16:06:32 +0000 (09:06 -0700)]
netdevice: demote the type of some dev_addr_set() helpers
__dev_addr_set() and dev_addr_mod() and pretty low level,
let the arguments be void, there's no chance for confusion
in callers converted to use them. Keep u8 in dev_addr_set()
because some of the callers are converted from a loop
and we want to make sure assignments are not from an array
of a different type.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 13 Oct 2021 16:40:49 +0000 (09:40 -0700)]
Merge branch 'net-constify-dev_addr-passing-for-protocols'
Jakub Kicinski says:
====================
net: constify dev_addr passing for protocols
Commit
406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
netdev->dev_addr will be made const to prevent direct writes.
This set sprinkles const across variables and arguments in protocol
code which are used to hold references to netdev->dev_addr.
====================
Link: https://lore.kernel.org/r/20211012155840.4151590-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 12 Oct 2021 15:58:40 +0000 (08:58 -0700)]
decnet: constify dev_addr passing
In preparation for netdev->dev_addr being constant
make all relevant arguments in decnet constant.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 12 Oct 2021 15:58:39 +0000 (08:58 -0700)]
tipc: constify dev_addr passing
In preparation for netdev->dev_addr being constant
make all relevant arguments in tipc constant.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 12 Oct 2021 15:58:38 +0000 (08:58 -0700)]
ipv6: constify dev_addr passing
In preparation for netdev->dev_addr being constant
make all relevant arguments in ndisc constant.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 12 Oct 2021 15:58:37 +0000 (08:58 -0700)]
llc/snap: constify dev_addr passing
In preparation for netdev->dev_addr being constant
make all relevant arguments in LLC and SNAP constant.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 12 Oct 2021 15:58:36 +0000 (08:58 -0700)]
rose: constify dev_addr passing
In preparation for netdev->dev_addr being constant
make all relevant arguments in rose constant.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 12 Oct 2021 15:58:35 +0000 (08:58 -0700)]
ax25: constify dev_addr passing
In preparation for netdev->dev_addr being constant
make all relevant arguments in AX25 constant.
Modify callers as well (netrom, rose).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 13 Oct 2021 16:08:59 +0000 (09:08 -0700)]
Merge branch 'add-functional-support-for-gigabit-ethernet-driver'
Biju Das says:
====================
Add functional support for Gigabit Ethernet driver
The DMAC and EMAC blocks of Gigabit Ethernet IP found on RZ/G2L SoC are
similar to the R-Car Ethernet AVB IP.
The Gigabit Ethernet IP consists of Ethernet controller (E-MAC), Internal
TCP/IP Offload Engine (TOE) and Dedicated Direct memory access controller
(DMAC).
With a few changes in the driver we can support both IPs.
This patch series is aims to add functional support for Gigabit Ethernet
driver by filling all the stubs except set_features.
set_feature patch will send as separate RFC patch along with rx_checksum
patch, as it needs further discussion related to HW checksum.
With this series, we can do boot kernel with rootFS mounted on NFS on
RZ/G2L platforms.
====================
Link: https://lore.kernel.org/r/20211012163613.30030-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Biju Das [Tue, 12 Oct 2021 16:36:13 +0000 (17:36 +0100)]
ravb: Fix typo AVB->DMAC
Fix the typo AVB->DMAC in comment, as the code following the comment
is for DMAC on Gigabit Ethernet IP.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Biju Das [Tue, 12 Oct 2021 16:36:12 +0000 (17:36 +0100)]
ravb: Update ravb_emac_init_gbeth()
This patch enables Receive/Transmit port of TOE and removes
the setting of promiscuous bit from EMAC configuration mode register.
This patch also update EMAC configuration mode comment from
"PAUSE prohibition" to "EMAC Mode: PAUSE prohibition; Duplex; TX;
RX; CRC Pass Through".
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Biju Das [Tue, 12 Oct 2021 16:36:11 +0000 (17:36 +0100)]
ravb: Document PFRI register bit
Document PFRI register bit, as it is documented on R-Car Gen3 and
RZ/G2L hardware manuals.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Biju Das [Tue, 12 Oct 2021 16:36:10 +0000 (17:36 +0100)]
ravb: Rename "nc_queue" feature bit
Rename the feature bit "nc_queue" with "nc_queues" as AVB DMAC has
RX and TX NC queues.
There is no functional change.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Biju Das [Tue, 12 Oct 2021 16:36:09 +0000 (17:36 +0100)]
ravb: Optimize ravb_emac_init_gbeth function
Optimize CXR31 register initialization on ravb_emac_init_gbeth
function.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Biju Das [Tue, 12 Oct 2021 16:36:08 +0000 (17:36 +0100)]
ravb: Rename "tsrq" variable
Rename the variable "tsrq" with "tccr_mask" as we are passing
TCCR mask to the ravb_wait() function.
There is no functional change.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
OSDN Git Service
